Scribd
Upload
2K views

Experiment With Optical Pyrometer

The document describes an experiment using an optical pyrometer to measure the temperature of a hot body. It discusses the Planck radiation law that optical pyrometers are based on and how they work by comparing the radiation of an unknown source to that of a calibrated tungsten lamp. The experiment varied the voltage applied to a hot wire and measured its temperature using the optical pyrometer both with and without a red filter or smoke glass. The results showed the temperature increasing with voltage and differences between readings taken with the various filters. Sources of error from the object's unknown emissivity are also discussed.

Uploaded by

sanatb_88
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
2K views

Experiment With Optical Pyrometer

The document describes an experiment using an optical pyrometer to measure the temperature of a hot body. It discusses the Planck radiation law that optical pyrometers are based on and how they work by comparing the radiation of an unknown source to that of a calibrated tungsten lamp. The experiment varied the voltage applied to a hot wire and measured its temperature using the optical pyrometer both with and without a red filter or smoke glass. The results showed the temperature increasing with voltage and differences between readings taken with the various filters. Sources of error from the object's unknown emissivity are also discussed.

Uploaded by

sanatb_88
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Experiment with Optical Pyrometer

Objective:
To measure the temperature of a hot body using optical
pyrometer.

Theory:
The optical pyrometer principle is based on Planck’s Radiation
Law. The law is given below:

• The primary law governing blackbody radiation is the Planck


Radiation Law.
• This law governs the intensity of radiation Ib(λ,T) emitted by
unit surface area into a fixed direction (solid angle) from the
blackbody as a function of wavelength for a fixed
temperature.
• The Planck Law can be expressed through the following
equation.

2hc2 1
Ib ( λ,T ) = 5 Wm −2 sr −1 µm −1
λ hc
e λkT
−1
h = 6.625 X 10-27 erg-sec (Planck Constant)
K = 1.38 X 10-16 erg/K (Boltzmann Constant)
C = Speed of light in vacuum
λ = Wavelength of the emission
T = Absolute temperature of the body.

Optical pyrometers are narrow-band or two-color radiation


pyrometers that operate in the visible spectrum around the 0.65-
μm point. The human eye, acting as the detector in the manually
balanced type, compares a source of known radiant energy
generated within the instrument by a calibrated tungsten lamp to
the incoming unknown source. A filter interposed between the
eye and both sources of energy cuts out the shorter wavelengths.
This serves a dual purpose: (1) it minimizes the difference
between eyes, permitting an easier color match, and (2) it
permits an extension of the temperature range beyond the point
where the eye could no longer tolerate the amount of energy if
viewed directly (Figure 4.9k). The instrument is shaped to be held
in the hand and up to the eye so that it may be sighted on the
target. An adjustable focus permits the operator to focus an
image of the source whose temperature is to be determined. The
filament of the standard source is placed on the same plane as
this image so that the two appear superimposed on one another
when viewed through the eyepiece. A null type of balance is
usually used where a rheostat, moving against a calibrated dial, is
manually rotated to vary the current through the standard source
until it just disappears into the field of the unknown. A slight
modification of this principle maintains the standard source
constant and varies the amount of interposing absorbing gate
opening in the optical path. The range of the manual optical
pyrometer is limited on the low end to a minimum of 1400°F
(760°C), since there is insufficient emission of visible light for an
accurate comparison below this figure. At 2400°F (1316°C), the
image would become too bright to look at directly, but filters are
usually interposed to permit readings as high as 6300°F (3500°C).
The use of the human eye as the detector restricts accuracy
somewhat. This is because the eye responds to both color and
brightness rather than directly to energy and no two eyes are
alike. However, it is possible to detect both a color and a
brightness match by adjusting to the minimum difference
between known and unknown. The schematic diagram of an
optical pyrometer is given below:
Red Lens
Eye

Slide
Calibrated
Targ
tungsten
lamp

Ammeter
calibrated in
temperature
scale

A bridge circuit can be used to detect the temperature. As,


changing the slide wire the current through tungsten wire is
controlled, the temperature of the wire is directly proportional to
the slide wire resistance. Using Wheatstone bridge arrangement
we can detect the resistance change and thereby the
temperature. In this case the null detecting voltmeter must be
calibrated in temperature scale as its deflection is the measure of
temperature.

Experimental results:
Variac Temperatur Temperatur Temperatur Temperatur
voltage (V) e reading e reading e reading e reading
(C) (C) (C) (C)
Increasing Increasing Decreasing Decreasing
temp. (with temp. (with temp. (with temp. (with
red filter) smoke red filter) smoke
glass) glass)
40 990 - 870 -
50 1030 - 970 -
60 1100 - 1100 -
70 1180 - 1200 -
80 1220 1370 1270 -
90 1290 1480 1270 1380
100 - 1510 1300 1430
110 - 1540 - 1470
120 - 1640 - 1520
130 - 1680 - 1580
140 - 1760 - 1620
150 - 1860 - 1800
160 - 1920 - 1920

Discussions:
1. Emissivity error:
The emissivity of the radiating body is unknown in this
method of temperature measurement. This introduces
measurement error as we are applying Planck’s Law
assuming the body is perfect black body. For the materials
other than black body the equation will be:
I(λ,T)=c1ελec2λT-1
Where ελ= emissivity of the radiating body.
When the filament disappears in the image of radiating
body, equating their intensity I(λ,T) we can measure the
error due to emissivity.

The equation is:


λclnελ+1T1=1T

Where T1 is the actual temperature and T is the measured


temperature.

2. Industrial application:
Optical pyrometer is extensively used in industries for high
temperature measurement. It is a noncontact type
measurement so, the temperature in hazardous area can be
measured easily. This instrument is used to measure furnace
and kiln temperature.

You might also like