Nitoflor Eu50

Nitoflor EU50*
High strength epoxy underlay

Uses
Instructions for use
Provides an economical method of levelling floors prior to

laying epoxy screeds or toppings such as Nitoflor TF5000*,
Nitoflor SL2000* and Nitoflor SL4000*.
Surface Preparation
n Cost effective
It is essential that Nitoflor EU50 is applied to sound, clean

and dry surfaces in order that maximum bond strength is
achieved between the substrate and the flooring system. All
dust and debris should be removed prior to application of the
product or its primer.
n Quick and easy to lay
New concrete floors
n Seamless
Should be at least 21 days old (at 20C) with maximum

moisture content not exceeding 5%. Laitance deposits on
new concrete floors are best removed by light grit blasting,
mechanical scabbling or grinding.
Advantages
n Durable
Description
Nitoflor EU50 consists of specially graded aggregates bound

together with an epoxy resin and formulated to withstand
chemical attack and impact shock. The product is supplied
as a 3 component system comprising resin base, resin
hardener and aggregates. When correctly laid, Nitoflor EU50
will provide a surface with a slight texture ready to receive
applications of other Fosroc flooring systems.
Nitoflor EU50 is designed for application in the range of

10mm - 50mm: greater thickness can be achieved by the
application of subsequent layers.
Substrates should be dry and not suffer, or be likely to suffer,
from rising dampness. If necessary, suitable damp-proof
membranes should be installed to prevent this. Substrates
should not have a relative humidity greater than 80% at any
time during the installation.
Properties
The values given below are typical figures achieved in

laboratory tests. Actual values obtained on-site may show
minor variations from those quoted.
Physical properties
:
40 N/mm2 @ 7 days
:
:
:
70 minutes
10 hours
7 days
Nitoflor EU50
Curing characteristics @ 35C

Pot life
Initial hardness
Full cure
Mechanical cleaning methods are strongly recommended on

old concrete floors particularly where heavy contamination
by oil and grease has occurred or existing coatings are present.
These may well have been absorbed several millimetres into
the concrete. To ensure adhesion, all contamination should
be removed by the use of a proprietary chemical degreaser.
Priming
Design Criteria
Compressive strength
(BS 6319) part 2, 1983
Old concrete floors
All surfaces treated with Nitoflor EU50 should be primed with

a Nitocote Primer Sealer, an epoxy resin primer designed for
maximum absorption and adhesion to concrete substrates.
Add the entire contents of the smaller hardener tin to the base
tin and mix thoroughly. Once mixed, immediately apply the
primer in a thin continuous film to the clean prepared surfaces.
Work the primer into the surface and avoid over application
and ponding. On porous floors, Fosroc Primer Sealer will be
absorbed very quickly leaving characteristic light coloured
dry patches. It is recommended that a second priming coat is
applied in such cases.
While still wet, dress the surface with kg/m of antislip grain
no. 3 to provide a key for the application of Nitoflor EU50.
Ensure that the primer is touch dry prior to commencing
application
Mixing
Expansion joints
It is important that Nitoflor EU50 is mixed correctly.
Expansion joints in the existing substrate should be continued

through the Nitoflor EU50 and any subsequent topping, and
filled to the required level with a suitable sealantfrom the Fosroc
range - contact the local Fosroc office for further details
Suitable mixing equipment must be used, such equipment

being defined as either a drill and Fosroc Mixing Paddle (MR4),
or forced action mixers such as Creteangle, Mixall or similar
machines. Where large volumes of product are required a
small free fall concrete mixer may be used, however mix trials
should be conducted to assess machine suitability.
Immediately prior to mixing the first batch of Nitoflor EU50
the internal surfaces of the mixer and any mixing blades should
be wetted out with Fosroc Solvent 102*. Only sufficient
solvent should be added to the mixer to ensure complete
wetting of the surfaces with any excess being discarded prior
to the addition of the Nitoflor EU50.
Whilst the internal surfaces of the mixer are still wet with
solvent empty the complete aggregate bag from the
Nitoflor EU50 pack into the mixer. The aggregates should be
blended dry for one minute prior to the addition of the resin
from the Nitoflor EU50 pack. Empty the entire contents of
the resin hardener component into the can containing the
resin base component and mix until homogeneous. When
mixed, the resin components are to be added to the aggregate
in the mixer. Mixing of all components shall continue for a
further 3-5 minutes, until such time as the resin has evenly
coated all the aggregate.
Application
The mixed Nitoflor EU50 should be spread to uniform
thickness on the primed surface using either a garden rake or
the edge of a plastic trowel. The material should be thoroughly
tamped to ensure complete compaction and finally finished
to an open even texture using a wooden trowel. Screeding
rods are useful to maintain a minimum compacted thickness
of 10mm.
Cleaning
All tools and equipment should be cleaned immediately after
use with Fosroc Solvent 102
Technical Support
Fosroc offers a comprehensive range of high performance,

high quality flooring, jointing and repair products for both
new and existing floor surfaces. In addition, the company
offers a technical support package to specifiers, end-users
and contractors, as well as on-site technical assistance in
locations all over the world.
Limitations
Nitoflor EU50 must not be used in external conditions.
Estimating
Supply
Nitocote Primer Sealer
Nitoflor EU50
Antislip grains No 3
Fosroc Solvent 102
:
:
:
:
1 & 4 litre packs

12 litre packs
20 kg packs
5 litre packs
:
:
4-5 m2 per litre

1.2 m2/ pack @
10mm thickness
Coverage
Nitocote Primer Sealer
Nitoflor EU50
Note :
The material must be applied within the pot life after mixing
(see Properties). After this time unused material should be
discarded.
Overcoating
Overcoating of the Nitoflor EU50 with any other Fosroc floor
system should not start until the Nitoflor EU50 is at least 24
hours old. The primers advocated by the flooring systems are
to be employed prior to overcoating. It is very important that
the application of Nitoflor EU50 be sealed with Nitoflor EU5*
or Nitoflor EU10* prior to application of the primer.
Nitoflor EU50 - Page 2 of 4
The above coverage rates are given for guidance

only as actual quantities used will vary on nature of
substrate and conditions on site.
Precautions
Health and safety

Nitoflor EU50, Nitocote Primer Sealer, Fosroc Solvent 102,
should not come in contact with skin and eyes or be swallowed.
Avoid prolonged inhalation of solvent vapours.
Some people are sensitive to epoxy resins, hardeners and
solvents. Gloves, goggles and a barrier cream such as Kerodex
Antisolvent or Rozalex Antipaint should be used. Ensure
adequate ventilation and if working in enclosed areas use
suitable breathing apparatus.
If mixed resin comes into contact with the skin, it must be
removed before it hardens with a resin removing cream such
as Kerocleanse Standard Grade Skin Cleanser or Rozaklens
Industrial Skin Cleanser, followed by washing with soap and
water. Do not use solvent.
Fosroc Solvent 102 should be washed from the skin
immediately with soap and water.
Should accidental eye contamination occur with any of the
above products, wash well with plenty of clean water and seek
medical advice. If swallowed, seek medical attention
immediately. Do not induce vomiting.
Fire
Fosroc Solvent 102, is flammable. Do not expose to naked
flames or other sources of ignition. No smoking during use.
Containers should be tightly sealed when not in use. In the
event of a fire, extinguish with a CO2 or foam type extinguisher.
Flash points
Fosroc Solvent 102
33C
Also refer to the Material Safety Data Sheet.

Storage
Nitocote Primer Sealer and Nitoflor EU50 have a shelf life of

12 months when stored in a dry place below 35C in their
original, unopened packs.
Nitoflor EU50 - Page 3 of 4
Additional Information
Fosroc manufactures a wide range of complementary products

which include :
n waterproofing membranes & waterstops
n joint sealants & filler boards
n cementitious & epoxy grouts
n specialised flooring materials
Fosroc additionally offers a comprehensive package of
products specifically designed for the repair and refurbishment
of damaged concrete. Fosrocs Systematic Approach to
concrete repair features the following :
n hand-placed repair mortars
n spray grade repair mortars
n fluid micro-concretes
n chemically resistant epoxy mortars
n anti-carbonation/anti-chloride protective coatings
n chemical and abrasion resistant coatings
For further information on any of the above, please consult
your local Fosroc office - as below.
* Denotes the trademark of Fosroc International Limited
REGIONAL SALES OFFICES IN :
Al Gurg Fosroc LLC

P. O. Box 657
Dubai
United Arab Emirates
TEL : (04) 285 8606
FAX : (04) 285 9649
See separate data sheet
DUBAI
ABU DHABI
BAHRAIN
KUWAIT
OMAN
QATAR
Al Gurg Fosroc
Al Gurg Fosroc
YBA Kanoo
Boodai
GETCO
Tadmur
TEL : 285 8787
TEL : 673 1779
TEL : 738200
TEL : 481 7618
TEL : 771 5080
TEL : 441 3628
FAX : 285 2023
FAX : 673 1449
FAX : 732828
FAX : 483 2124
FAX : 771 7554
FAX : 444 0812
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard terms and conditions of sale, copies of which
may be obtained on request. Whilst Fosroc endeavours to ensure that the technical information on this data sheet is correct at the time of printing, it is the
customers responsibility to satisfy himself, by checking with the company that this information is still current at the time of use, that the product is suitable for
the intended application, and that the actual conditions of use are in accordance with those recommended. Because Fosroc has no control over the conditions of
use of its products, all recommendations or suggestions regarding the use of these products are made without guarantee.
www.fosrocgulf.com
UAE/0330/01/C

Nitoflor Eu50

Uploaded by

Copyright:

Available Formats

Nitoflor Eu50

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Nitoflor Eu50

Uploaded by

Copyright:

Available Formats

Nitoflor EU50*

High strength epoxy underlay

Instructions for use

Provides an economical method of levelling floors prior to

It is essential that Nitoflor EU50 is applied to sound, clean

n Quick and easy to lay

New concrete floors

Should be at least 21 days old (at 20C) with maximum

Nitoflor EU50 consists of specially graded aggregates bound

Nitoflor EU50 is designed for application in the range of

The values given below are typical figures achieved in

Curing characteristics @ 35C

Mechanical cleaning methods are strongly recommended on

Old concrete floors

All surfaces treated with Nitoflor EU50 should be primed with

It is important that Nitoflor EU50 is mixed correctly.

Expansion joints in the existing substrate should be continued

Suitable mixing equipment must be used, such equipment

Fosroc offers a comprehensive range of high performance,

Nitoflor EU50 must not be used in external conditions.

1 & 4 litre packs

4-5 m2 per litre

Nitoflor EU50 - Page 2 of 4

The above coverage rates are given for guidance

Health and safety

Also refer to the Material Safety Data Sheet.

Nitocote Primer Sealer and Nitoflor EU50 have a shelf life of

Nitoflor EU50 - Page 3 of 4

Fosroc manufactures a wide range of complementary products

* Denotes the trademark of Fosroc International Limited

REGIONAL SALES OFFICES IN :

Al Gurg Fosroc LLC

See separate data sheet

TEL : 285 8787

TEL : 673 1779

TEL : 481 7618

TEL : 771 5080

TEL : 441 3628

FAX : 285 2023

FAX : 673 1449

FAX : 483 2124

FAX : 771 7554

FAX : 444 0812

You might also like