CATV Lodget Hotel

LODGENET HOTEL INSTALLATION
OVERVIEW
TPD-5201-G
Rev. Date: 05-13-11
Copyright 2011 LodgeNet Interactive Corporation. All Rights Reserved.
TABLE OF CONTENTS
LODGENET HOTEL INSTALLATION OVERVIEW ____________________________________ 3
DISCLAIMER OF WARRANTIES ______________________________________________________________________ 3
DOCUMENT PURPOSE & DEFINITION _________________________________________________________________ 3
SECTION 1: LODGENET GUEST PAY AND FREE-TO-GUEST REQUIREMENTS _________ 4

GUEST PAY (GP) HARDWARE COMPONENTS __________________________________________________________ 4
FTG HARDWARE COMPONENTS _____________________________________________________________________ 4
RACK ROOM REQUIREMENTS _______________________________________________________________________ 5
RACK ROOM CABLING REQUIREMENTS ______________________________________________________________ 7
SATELLITE DISH REQUIREMENTS ___________________________________________________________________ 8
CIRCUIT/TELECOM REQUIREMENTS _________________________________________________________________ 9
GUEST ROOM REQUIREMENTS _____________________________________________________________________ 10
SECTION 2: CATV/MATV DISTRIBUTION REQUIREMENTS _________________________ 11

SIGNAL SPECIFICATIONS __________________________________________________________________________ 11
DISTRIBUTION CLOSET REQUIREMENTS ____________________________________________________________ 11
AMPLIFIER REQUIREMENTS _______________________________________________________________________ 11
DE-RATED AMPLIFIER INPUT/OUTPUT SPECIFICATIONS ______________________________________________ 12
PASSIVE DEVICE REQUIREMENTS __________________________________________________________________ 12
CABLE REQUIREMENTS ___________________________________________________________________________ 12
FIBER OPTICS TERMINOLOGY ______________________________________________________________________ 14
FIBER OPTICS CABLE REQUIREMENTS ______________________________________________________________ 14
CONDUIT REQUIREMENTS _________________________________________________________________________ 17
CONDUIT DIAGRAM _______________________________________________________________________________ 17
MATV CABLING OVERVIEW _______________________________________________________________________ 18
ADDITIONAL MATV INFORMATION _________________________________________________________________ 20
SECTION 3: DOCUMENTATION OF SYSTEM DESIGN AND PERFORMANCE __________ 21

AS-BUILT DIAGRAMS _____________________________________________________________________________ 21
IN ROOM DOCUMENTATION AND READINGS ________________________________________________________ 24
ADDITIONAL INFORMATION _______________________________________________________________________ 25
LodgeNet Hotel Installation Overview

TPD-5201-G 05-13-11
Page 2
LodgeNet Confidential - Use and Distribution

Subject to Confidentiality Obligation
LODGENET HOTEL INSTALLATION OVERVIEW

DISCLAIMER OF WARRANTIES
DISCLAIMER OF WARRANTIES: This document is intended for professional installers with MATV /
CATV design experience. The information contained in this document is provided "AS IS." You and your
construction advisors must independently determine the appropriateness of the information contained in
this document. LodgeNet expressly disclaims all warranties of any kind with respect to this document and
the information it contains, whether expressed or implied, including but not limited to the warranties of
merchantability and fitness for a particular purpose.
If you have questions or require additional assistance, please contact LodgeNets Professional Solutions
Group at 1-888-LODGENET or at professionalsolutions@lodgenet.com.
DOCUMENT PURPOSE & DEFINITION

This document provides guidance for the design and installation of an MATV/CATV distribution network
to support a LodgeNet system in a new hotel construction environment. A system properly designed and
built during the construction period will not only serve your immediate needs, but will also provide for
expandability, reliability, and serviceability in the future.
The LodgeNet system may be comprised of several solutions, including Guest Pay (GP) and Free-ToGuest (FTG) services. Each hotel may have any combination of these solutions installed. Each solution
has a specific set of requirements for installation and operation.
This document is comprised of three sections:
Section 1 - Provides specifications and guidance in the planning and installation of LodgeNets Guest
Pay platforms such as LodgeNet SD, LodgeNet HD, LodgeNet HD-Ready, Envision, and
LodgeNets Free-To-Guest (FTG) platforms (with a supplemental off-air system, if required).
Section 2 - Provides specifications and guidance in the planning and installation of a MATV/CATV
distribution system.
Section 3 - Provides examples and guidance for documenting the system design and performance.
The required documentation will include As-Built diagrams, a TV Type matrix showing hardware
combinations, and RF readings from the room.
Information found in this document can be freely duplicated and distributed to contractors and others
involved in the planning and construction of new hotels. LodgeNet is committed to providing interactive
products and services of the highest quality to the Lodging industry. If you have any questions about the
specifications found in this document, feel free to call us at 1-888-LODGENET.

TPD-5201-G 05-13-11
Page 3

SECTION 1: LODGENET GUEST PAY AND FREE-TO-GUEST

REQUIREMENTS
GUEST PAY (GP) HARDWARE COMPONENTS
LodgeNets Guest Pay platforms provide a powerful, customizable, interactive and informative
entertainment delivery system designed for guests. The hardware components within these platforms
include:
System Rack - Contains proprietary host computers, video file servers, and interactive TV enabling
equipment. The system rack may also include game equipment (Nintendo GameCube) and
Internet browser modules, depending on the requested or contracted services. Additionally, the rack
contains television processing and networking components.
LodgeNet Applications Wizard Administrative Menu Console - Functions as an administrative
terminal, allowing access to system management tools for system administration and diagnosis. The
Applications Wizard includes a small footprint computer console, a flat panel monitor, a keyboard, a
mouse, and two power supplies.
Network Printer - Used in conjunction with the Applications Wizard console and allows users to print
system information and reports.
TV Signal Insertion Point - Comprised of required splitters, combiners, and television distribution
amplifiers sufficient to introduce signals originating at the system racks with the existing TV cabling
network.
1, 1.2 or 1.8 Meter Satellite Dish - The Ku band satellite dish is used to receive schedule updates and
selected content downloads.
Guest Room Terminal - Connects to the existing compatible TV receiver, enabling it to function as an
interactive device.
Nintendo GameCube Hardware (Optional)
o Used only in sites contracted for the Nintendo service.
o The GameCube game controller controls GameCube game play on the TV through the guest
room terminal.
Guest Room Remote Control - Controls the functions of the TV and/or guest room terminal.
FTG HARDWARE COMPONENTS

The Free-To-Guest (FTG) TV programming service may provide a predetermined number of basic cable,
local, premium, DTV/HDTV local, and DTV/HDTV premium channels. The following hardware
components are included in LodgeNets Free-To-Guest TV programming service:
FTG Receiver Rack(s) - Contains digital satellite receiving equipment, as well as commercial
television processing and networking components.
TV Signal Insertion Point - Comprised of splitters, combiners, and TV distribution amplifiers
sufficient to introduce signals originating at the system racks with the existing TV cabling network.
1, 1.2 or 1.8 Meter Satellite Dish(es) - Ku and Ka band satellite dish(es) used to receive content.
Off-Air Antennas - Used to receive (local analog and local DTV/HDTV) broadcast channels not
available via satellite transmission.

TPD-5201-G 05-13-11
Page 4

RACK ROOM REQUIREMENTS

Security Requirements
The LodgeNet equipment room must be a secure, limited access area.
Preferred equipment locations include environmentally controlled telephone or computer rooms.
Backboard Requirements
A backboard of 3/4 plywood with a total area of 4 x 8 (split into two 4 x 4 boards is acceptable)
must be installed on a wall near the system rack(s) for mounting the mix point devices, distribution
amplifiers, and other related equipment.
Backboards must meet local fire-rating codes.
Space Requirements
Rack room entrance or door must be at least 32 (w) and 80 (h).
LodgeNet System Rack Dimensions: 79 (h), 22 9/16 (w), and 31 (d).
LodgeNet System Racks require a minimum of 5(w) x 8(d) of unobstructed floor space, with 8 of
head room for the first rack (includes walk around).
An additional 2(w) x 8(d) of unobstructed floor space is required for each additional rack.
Depending on the services being installed, you will need at least one GP rack and up to 3 FTG
racks. To determine the number of racks required, please contact LodgeNet for further
information.
Applications Wizard Dimensions (Can be located outside the rack room):

o Computer Console: 2.5 (h), 11.5 (w), 11 (d).
o Flat Panel Monitor: 14 (h), 17.5 (w), 7 (d).
o Keyboard: 1 (h), 15.7 (w), 9.25 (d).
Network Printer Dimensions (Can be located outside the rack room):

o 8.3 (h), 14.3 (w), 14.5 (d).

TPD-5201-G 05-13-11
Page 5

Electrical Circuit Requirements

Guest Pay:
o Hotels containing 630 rooms or less will require one 30A-110VAC circuit.
o Hotels containing more than 630 rooms must contact LodgeNet for specific electrical
requirements.
o Applications Wizard - Two outlets. (One 15 amp circuit / may be behind the front desk.)
o Printer - One outlet. (One 15 amp circuit may be behind the front desk.)
Free-To-Guest:
o Each FTG Rack - One 15A circuit with two standard 15A outlets.
General:
o Insertion Point Launch Amp - One outlet (typical).
Conduit Requirements
Guest Pay:
o One 3 diameter conduit for LodgeNets exclusive use must be provided from the GP rack
location to the satellite dish location (400-foot maximum distance if using coaxial cables. Longer
distances are acceptable with fiber optics cabling).
At the dish location, conduits must terminate into a 12 x 12 x 6 weatherproof box.
Free-To-Guest:
o One 3 diameter conduit for LodgeNets exclusive use must be provided from the FTG rack
location to the satellite dish location (250-foot maximum distance if using coaxial cables. Longer
distances are acceptable with fiber optics cabling).
o One 3 diameter conduit for LodgeNets exclusive use must be provided from the FTG rack
location to the antenna location on the roof (if signals are received via antenna).
General:
o One 2 diameter conduit for LodgeNets exclusive use must be provided from each of the rack
locations to the hotels main distribution point location (if GP, FTG, and the main distribution
point are not located in the same room).
o One 2 diameter conduit for LodgeNets exclusive use must be provided from the headend rack
location to the front desk area. (Distance limitations may apply.)
location to the hotels Property Management System (PMS) location. (Distance limitations may
apply.)
location to each additional remote system interface (Applications Wizard) location. (Distance
limitations may apply.)
HVAC Requirements
General:
o The LodgeNet rack temperature must be maintained between 50F75F.
Guest Pay:
o Refer to the following table to determine the heat loading by the number of rooms:
Room Count
Rack Count
Power (Watts)
Heat (BTU)*
50 - 150
1
665
2270
SYSTEM HVAC REQUIREMENTS

151 - 270 271 - 390 391 - 510 511 - 630
1
1
1
1
1246
1272
1307
1336
4250
4340
4460
4560
Over 630
Contact LodgeNet
*To calculate the total amount of heat generated, add the heat generated by the Free-To-Guest equipment
installed in the same location as the Guest Pay equipment to the heat figures in the table above.
TPD-5201-G 05-13-11
Page 6

Free-To-Guest:
o Refer to the following table to determine the heat loading by type of FTG channel:
FTG HVAC REQUIREMENTS

Type and # of Channels
BTUs
Up to 40 DIRECTV SD (Analog) Satellite Channels
4843
Up to 12 DIRECTV HD Satellite Channels
5064
Up to 12 Digital HD Off-Air (Local) Channels
1284
For More Channels

Contact LodgeNet
Note: To calculate the total amount of heat generated in the rack room, add the heat generated by the
Guest Pay equipment installed in the same location as the Free-To-Guest equipment to the total heat
figures in the table above.
RACK ROOM CABLING REQUIREMENTS

The following guidelines and diagrams detail the cable run specifications from the system rack location:
CAT5 Cabling Requirements
One CAT5 cable required for the Applications Wizard.
One CAT5 cable required for the network printer.
One CAT5 cable required as a spare for the front office equipment.
One CAT5 cable required for the broadband Internet connection.
One CAT5 cable required for Networked PC Access (if applicable).
If FTG is installed, an additional CAT5 cable must be installed between the GP and FTG racks.
CAT5 cable runs greater than 328 feet will require the use of an Ethernet hub or a pair of Ethernet
extenders between the system rack and the connected device. Note: AC power is required at the hub
or Ethernet extender location.
RS-232 Cabling Requirements
One RS-232 cable required for the connection to the hotels Property Management System.
One RS-232 cable required as a spare for the hotels Property Management System.
If FTG is installed, a data cable is required between the GP and FTG racks.
o CAT5 cable may be used if the GP and FTG racks are in separate locations.
Coaxial Cable
RG-11 coaxial cable is required for the satellite dish.
RG-11 coaxial cable is required to the MATV distribution point.
o Swept from 5 MHz1 GHz.

TPD-5201-G 05-13-11
Page 7

Guest Pay System Cabling Diagram
SATELLITE DISH REQUIREMENTS

Satellite Dishes
Guest Pay:
o One 1-meter satellite dish is required for the LodgeNet system.
A 1.2 or 1.8 meter satellite dish may be needed in select areas.
If HD VOD is being installed with an On Command headend system, an additional 1-meter
satellite dish is required. (A 1.2 meter satellite dish may be needed in select areas.)
o The satellite dish location requires an unobstructed view of the sky facing 103 degrees west.
o It is important that the satellite dish location be no more than 400 feet from the LodgeNet system
racks if using coaxial cable. For longer distances, fiber optics cabling is required. (Because of this
limitation, a roof location may not always be acceptable.)
Free-To-Guest:
o Up to 6 satellite dishes (1 or 1.2 meter depending on location) may be required for digital satellite
programming services.
o The satellite dish location requires an unobstructed view of the sky from 72.5 degrees west to 119
degrees west.
o It is important that the satellite dish location be no more than 250 feet from the LodgeNet system
racks if using coaxial cable. For longer distances, fiber optics cabling is required. (Because of this
limitation, a roof location may not always be acceptable.)
General:
o Contact LodgeNet for assistance when determining the number and diameter of antenna or
satellite masts required for the installation.
o All masts must be properly grounded. (Refer to NEC code, Article 810, Section 810-21.)
o If the satellite dish will be installed on the roof without a permanent mast, a non-penetrating
ballasted roof mount must be used. Therefore, the roof must be able to withstand continuous roof
loading of 45 lbs. per sq. ft.
o Satellite dishes must be in an accessible location for service.

TPD-5201-G 05-13-11
Page 8

Antennas
Off-air antennas must be on the exterior roof of the building and in a location that provides a clear
line of sight to the surrounding area.
Three 6 antenna masts spaced 5 apart and properly secured during construction may reduce cost.
Space Requirements
1 meter satellite dish mount: Baird B3 34 x 40 Mount
o Typical mast dimensions: 30 (h) x 35 (w) x 40 (d)
1.2 meter satellite dish mount: Baird B4 6 x 6 Mount
o Typical mast dimensions: 36 (h) x 75 (w) x 72 (d)
1.8 meter satellite dish mount: Baird B6-11 11 x 11 Mount
o Typical mast dimensions: 36 (h) x 130.75 (w) x 130.75 (d)
Ballast
In applications where a non-penetrating roof mount is deployed, ballast in the form of sandbags or
concrete blocks must be used.
The amount of ballast required will vary, based on local conditions such as the surface area of the
dish, height of the building, and the typical area wind speeds.
Cables
All weather-exposed cables must be placed in conduit and terminated with a weather head.
o Exposed cable for service loops should be limited to no more than 5 feet and should be
adequately dressed (not laying on roof).
Connectors should be of the weatherproof type or sealed with weatherproof compound.
Electrical Outlet Requirements
Power is provided from the system rack via RG-11 coaxial cable. No additional electrical outlets are
required at the satellite dish location.
CIRCUIT/TELECOM REQUIREMENTS
The LodgeNet system must have a dedicated Internet circuit or be on a shared circuit with bandwidth
management allowing a portion of the circuit to be dedicated to LodgeNet services. Please reference your
specific agreement for details.
Supported Interfaces
Supported interface types: 10Base-T (Ethernet), or 100Base-T (Fast-Ethernet).
Public Routable IP Address
IP addresses must be assigned from the Internet Service Provider (ISP) before the system is installed.
This IP address may also be referred to as the host IP or customer IP.
The LodgeNet system requires (1) public routable IP address. This may also be referred to as a static
IP address.
The address must be static - It must not be Dynamic Host Configuration Protocol (DHCP) assigned or
be a DHCP sticky IP address.
The IP address must not be Network Address Translated (NAT), must not be shared with another
system, and must not be firewalled or filtered.

TPD-5201-G 05-13-11
Page 9

The IP address must not be an RFC-1918 private, unroutable IP address that is masqueraded, spoofed,
or translated. The following IP addresses are not supported (RFC-1918):
o Addresses that begin with 10
o Addresses that begin with 192.168
o Addresses that begin with 172.16-31
Subnet Mask
The subnet mask is assigned from the ISP in conjunction with the host IP address.
Examples: IP: 12.100.100.100 subnet mask: 255.255.255.248
IP: 12.100.100.100/29 (The /29 is the subnet mask)
Gateway IP Address
The Gateway IP address is also assigned from the ISP in conjunction with the host IP address. This
will be denoted as Gateway Address, Gateway IP, or Default Gateway.
GUEST ROOM REQUIREMENTS

Guest Room Hardware Components
In-Room terminal.
Remote control.
GameCube hardware (Optional) - Used only in systems with Nintendo games.
o GameCube Game Controller - 2 (h) x 5.5 (w) x 4 (d).
o The controller must be placed near the TV.
LodgeNet LaunchPad or guestLINK PowerWave (Optional) Both solutions connect your inroom TV and audio to your guests personal devices including laptops, MP3 players, personal
gaming stations, DVD players, digital cameras, smartphones, digital video cameras, and more.
Electrical Outlet Requirements
Non-integrated terminals only - The existing TV power cord must plug into the convenience outlet
provided on the power supply. The guest room terminal power supply plugs into a vacated nonswitched outlet. No additional outlet is required.
Security Requirements
Metal, tamper-resistant sleeves for coaxial cable ends (provided).
Television Receivers
The LodgeNet system is designed to work with a wide variety of TV models.
Please consult your LodgeNet representative to ensure compatibility of TVs before purchasing new
TVs.

TPD-5201-G 05-13-11
Page 10

SECTION 2: CATV/MATV DISTRIBUTION REQUIREMENTS

SIGNAL SPECIFICATIONS
The recommended MATV/CATV distribution systems forward frequency response must be at 49

MHz860 MHz with +3 to +10 dBmV on every channel at each TV outlet. The return response must
be 5 MHz35 MHz.
The system must be able to deliver 6 to 10 dBmV return level at 5 MHz35 MHz to the headend, with
a 36 dBmV reference from a typical room location.
The system must maintain a room-to-room isolation of 23 dB or greater.
DISTRIBUTION CLOSET REQUIREMENTS
Must be a secure, limited access area.

A backboard of 3/4 plywood with a total area of 4 x 4 must be installed on the wall in each
distribution closet. Each backboard must meet local fire-rating codes.
If the distribution closets require amplifiers, a non-switched 10A 120VAC circuit must be provided at
the backboard.
A 2 conduit must be provided from each distribution closet to the headend.
AMPLIFIER REQUIREMENTS
Amplifiers must be bi-directional with a forward frequency pass range of at least 49 MHz to 860
MHz. The return rating should be between 5 MHz and 35 MHz.
The amplifiers output must not exceed 44 dBmV at 860 MHz. Frequencies between 225 MHz and
400 MHz should not exceed 38.75 dBmV.
Amplifiers must be mounted on spacers that are a minimum of 1/2 from the plywood backboard to
allow for adequate cooling.
Amplifiers should be located in, or as close to the distribution closets as possible.
The following amplifier input specifications denote levels after all internal pads and equalizers are
installed:
Make
BT
BT
BT
BT
Drake
Drake
Drake
Drake
Model
BIDA 75A-30P
BIDA 75A-43P
BIDA 86A-30P
BIDA 86A-43P
DA7533-750P-33
DA7543-750P-43
DA8632-860P-32
DA8642-860P-42
Max Input
14
5
14
5
14
5
14
5
Min Input
8
2
8
2
8
2
8
2
Max Output @ Max Input

44
44
44
44
44
44
44
44
Amplifier cascading (multiple amplifiers in the same signal path) should be kept to a minimum.
Cascading high gain amps (over 35 dBmV gain) is not recommended.
Every time amplifiers are cascaded, the inputs and max outputs must be systematically reduced as
listed in the De-Rated Amplifiers Input/Output Specifications section below.

TPD-5201-G 05-13-11
Page 11

DE-RATED AMPLIFIER INPUT/OUTPUT SPECIFICATIONS

Refer to the following tables for the input and output specifications for 30 dBmV and 43 dBmV cascaded
amplifiers:
30 dBmV Gain Cascaded Amplifier Input/Output Specifications
44 dBmV
43 dBmV
42 dBmV
41 dBmV
Cascade
Max
Max
Max
Max
Max
Max
Max
Max
Number
Input
Output
Input
Output Input
Output
Input
Output
1
14
44
14
43
14
42
14
41
2
11
41
11
41
11
41
11
39
3
9
39
9
39
9
39
9
37
4
8
38
8
38
8
38
8
36
Cascade
Number
1
2
3
4
High Gain (43 dBmV) Cascaded Amplifier Input/Output Specifications

44 dBmV
43 dBmV
42 dBmV
41 dBmV
Max
Max
Max
Max
Max
Max
Max
Max
Input
Output
Input
Output Input
Output
Input
Output
5
44
5
43
5
42
5
41
4
41
4
41
4
41
4
41
3
39
3
39
3
39
3
39
2
38
2
38
2
38
2
38
PASSIVE DEVICE REQUIREMENTS
Passive devices (taps, splitters, etc.) must have a frequency rating of 5 MHz1 GHz and a shielding
rating of 100 dB RFI or greater.
All passive devices must be located in an accessible location. Passive devices installed in ceilings or
walls must have access panels provided.
Devices must have a minimum port-to-port isolation of 23 dB or greater.
CABLE REQUIREMENTS
Main trunk cables should be CATVR rated RG-11 cable, swept from 5 MHz1 GHz. (See the Cable
Specification Chart for minimum cable requirements and the Maximum Cable Attenuation Chart for
sweep specifications.) Hardline cable .500 or larger is also acceptable.
Underground cable runs that connect separate buildings must use flooded type cable and be in
conduit. RG-11 or hardline cable should be used for runs up to 500 feet.
Hardline cable or fiber cable should be considered for runs of 500 or more. Hardline attenuation
losses must be considered when hardline is used.
Riser cabling should be CATVR cable, swept from 5 MHz1 GHz.
Cable runs should not contain splices.
Always use plenum-grade CATVP cable where required by local code or when installing cable in
plenum ceilings without conduit.
RG-59 type cable is not recommended.
Compression or radial type fittings should be used for RG-6 coaxial cable connectors. RG-11 coaxial
cable can use compression-type or hex-crimp connectors with a crimped center conductor pin.
All cable pulls prior to termination must leave a 3-foot service loop.
Coaxial cable type and installation must meet NEC codes for fire safety.
All weather-exposed cables must be the flooded type.

TPD-5201-G 05-13-11
Page 12

Cable Type
Riser Rated
RG-6
Plenum Rated
RG-6
Riser Rated
RG-11
Plenum Rated
RG-11
Cable Type
Conductor Size,
Construction and
Diameter
Cable Specification Chart
18 AWG Copper-Clad Steel.

Nom. 0.0403
Nom 0.0403
Nom. 0.0641
Nom. 0.0641
Riser Rated RG-6

Plenum Rated RG-6
Riser Rated RG-11
Plenum Rated RG-11
1 MHz
0.37 dB
0.38 dB
0.17 dB
0.15 dB
Dielectric Type
and Diameter
Shielding Type and Coverage

(Minimum)
Jacket Type and Thickness
Overall
Diameter
Foam Polyethylene.
Nom. OD 0.180
Foam FEP Nom.
OD 0.170
Foam Polyethylene.
Nom. OD 0.280
Foam FEP Nom.
OD 0.280
Foil: Aluminum/Poly tap 100% coverage

Braid: 34 AWG Aluminum 60% coverage
Flame Retardant PVC. Nom.

0.030
Plenum PVC or Kynar (PVDF)
Nom. 0.015
Flame Retardant PVC. Nom.
0.045
Plenum PVC or Kynar (PVDF)
Nom. 0.020
Nom. 0.272
(+/- 0.004)
Nom. 0.239
(+/- 0.006)
Nom. 0.405
(+/- 0.010)
Nom. 0.351
(+/- 0.006)
10 MHz
Maximum Cable Attenuation Chart (dB/100 ft.)

50 MHz
100 MHz
200 MHz
400 MHz
700 MHz
900 MHz
1000 MHz
Maximum Cable Attenuation Chart (dB/100 ft.)

250 MHz
350 MHz
450 MHz
550 MHz
750 MHz
865 MHz
1000 MHz
2.16 dB
1.48 dB
2.34 dB
1.61 dB
2.52 dB
1.74 dB
0.66 dB
0.70 dB
0.45 dB
0.45 dB
Cable Type
5 MHz
55 MHz
.500 Hardline
.750 Hardline
0.16 dB
.11 dB
0.54 dB
0.37 dB
1.41 dB
1.48 dB
0.89 dB
0.90 dB

TPD-5201-G 05-13-11
1.2 dB
0.81 dB
1.92 dB
2.01 dB
1.21 dB
1.28 dB
1.43 dB
0.97 dB
Page 13
2.64 dB
2.86 dB
1.68 dB
1.85 dB
1.63 dB
1.12 dB
3.73 dB
4.23 dB
2.37 dB
2.75 dB
1.82 dB
1.24 dB
5.05 dB
5.96 dB
3.27 dB
3.92 dB
5.79 dB
6.96 dB
3.77 dB
4.72 dB

6.11 dB
7.45 dB
3.95 dB
5.04 dB
FIBER OPTICS TERMINOLOGY
FFT Forward Fiber Transmitter.

FFR Forward Fiber Receiver.
RFT Return Fiber Transmitter.
RFR Return Fiber Receiver.
WDM Wavelength Division Multiplexing. This is used when forward and return signals share a
single strand of fiber.
SC/APC This is a type of fiber polish/termination that allows for the transfer of light with low
optical loss. SC is a push/pull connector style with a positive locking mechanism. APC stands for
Angle Physical Contact.
FIBER OPTICS CABLE REQUIREMENTS

General Requirements
Fiber optics cables are acceptable for trunk line runs and should be considered for runs over 1000
feet.
All fiber optics cables for RF and L-band transmissions must be single mode 9/125m.
The light source can be either 1310nm or 1550nm. Some manufacturers use 1310nm for forward
signals and 1550nm for return signals.
If non-armored cable is used, conduit should be considered (reference local codes for requirements).
LodgeNet recommends a minimum of two fiber strands to all locations.
o Additional spares are recommended if forward and return signals are to be run on separate cables.
o If fiber is being used for runs from dish locations, please contact LodgeNet for assistance.
All cable splices must be fusion splices. Mechanical splices are not acceptable.
Minimum cable bend ratio should not be less then 10x the diameter of the cable (~ 2 minimum).
The use of cable trays and Velcro cable management devices are preferred, as these prevent kinks in
the cable.
All cables must be adequately supported and secured to prevent damage during normal operation.
All fiber optics cable runs must be terminated and tested by the fiber installation contractor.
Cables should be terminated with SC/APC terminations.
LodgeNet does not currently support fiber to the room.
If fiber optics cabling is being used for runs from dish locations to the headend or in conjunction with
On Command head end equipment, please contact LodgeNet for assistance.
The hotel must either provide or pay for fiber optical link equipment for both forward and return
signals (transmitters and receivers).
RF Application Requirements
The forward path FFT (Forward Fiber Transmitter) and FFR (Forward Fiber Receiver) must support a
forward frequency of at least 49 MHz to 860 MHz.
The return path RFR (Return Fiber Receiver) and RFT (Return Fiber Transmitter) must support a
return frequency of at least 5 MHz 35 MHz. The return path must be capable of producing 6-10
dBmV from a typical room (middle room/middle riser) back to the headend location with a 36 dBmV
reference.
Either separate fiber strands or a single fiber strand with WDM can be used for transmitting forward
and return signals.
Diplexers must be installed on both ends of the fiber optics strands if separate fiber strands are used
for forward and return signals.
TPD-5201-G 05-13-11
Page 14

Diplexers must be incorporated into the WDM equipment if WDM is deployed.

The FFR and RFR must meet a minimum output of 8 dBmV to work with the current LodgeNet
BIDA amplifiers.
The RF input requirements for the FFT and RFT must be set up according to the equipments
specifications.
The optical transmitters should be sized so that the signal reaches the receiver at -1 dBmV (+/- 3
dBmV) after accounting for optical loss.
L-Band Application Requirements

Fiber optics cabling can be used to transmit L-band signals from the LodgeNet satellite dish to the
headend location.
Fiber optics cables are recommended for distances over 400 feet.
The fiber optics path is single direction when used to transmit L-band signals from the dish to the
headend. No return path is required.
The FFT and FFR equipment must support the standard L-band frequency range (minimum of 250
MHz 2150 MHz).
DIRECTV Application Requirements
Fiber optics cabling can be used to transmit L-band signals from the FTG satellite dish(es) to the
LodgeNet headend location.
Fiber optics cables are recommended for distances over 250 feet.
The fiber optics path is single direction when used to transmit DIRECTV signals from the dish to the
headend. No return path is required.
The FFT and FFR equipment must support the standard L-band frequency range (minimum of 250
MHz 2150 MHz).
A minimum of four fiber optics strands must be run from the satellite dish location to the headend
with additional strands to serve as spares.
Data/IPTV Application Requirements
This document does not cover the use of fiber optics for data or IPTV applications.

TPD-5201-G 05-13-11
Page 15

Example 1: Fiber Optics Trunk
Example 2: Fiber Optics Trunk

TPD-5201-G 05-13-11
Page 16

CONDUIT REQUIREMENTS
The use of conduit for all MATV/CATV wiring, including room drops, is highly recommended.
Underground cable runs that connect separate buildings must use flooded type cable and be in
conduit. RG-11 or hardline cable should be used for runs up to 500 feet. Hardline cable is required for
runs of 500 feet or more.
All conduits must contain a pull string.
CONDUIT DIAGRAM
The following diagram indicates the type(s) of conduit to be used according to the aforementioned
guidelines within this document. Therefore, this diagram should only be used as a reference or aid in
conjunction with those guidelines.

TPD-5201-G 05-13-11
Page 17

MATV CABLING OVERVIEW

A properly designed and maintained MATV distribution system is critical to the delivery of quality
television entertainment and information services. Two methods are recommended for the design and
layout of MATV/CATV distribution systems:
Method #1: RG-6 homeruns to each room from distribution closets or the system rack.
Method #2: Horizontal RG-11 trunks feeding 4-port and 2-port drop taps. Drop tap legs feed individual
rooms with RG-6.
Meeting rooms and public area wiring must be on a separate trunk or riser from the guest rooms.
Loop-through riser configurations are not recommended.
For best results, Method #1 should always be employed in new construction.
Method #1: Homerun Installation Guidelines
All rooms terminate with pass-through F-81 connectors at the wall plate.
Use RG-11 or .500 hardline for all trunk lines from the system rack to the distribution closets.
Values of splitters or directional couplers should be chosen to allow more signal to be fed to distant
rooms. This helps compensate for increased signal loss over long distances.
Splitters and directional couplers are used in the system rack room or distribution closets to distribute
signals to the rooms.
Diagram A: Method #1 Homerun Installation

TPD-5201-G 05-13-11
Page 18

Diagram B: Method #1 Homerun Installation
Method #2: Semi-Homerun Installation Guidelines

Trunks must be designed to ensure that drop taps decrease in value the further from the beginning of
the trunk to provide signal levels from +3 dBmV to +10 dBmV to each outlet.
2-port drop taps can be used whenever less than 3 rooms need to be fed. Note: Feeding end rooms
from the tap throughput is not acceptable.
Trunk lines can be home run from the system rack or fed from distribution closets.

TPD-5201-G 05-13-11
Page 19

Diagram C: Method #2 4-Way Drops
Diagram D: Method #2 Descending 4-Way Drop Tap Installation
ADDITIONAL MATV INFORMATION

For additional MATV information, questions, or MATV design, please contact LodgeNets Professional
Solutions Group at 1-888-LODGENET or at professionalsolutions@lodgenet.com.

TPD-5201-G 05-13-11
Page 20

SECTION 3: DOCUMENTATION OF SYSTEM DESIGN AND

PERFORMANCE
AS-BUILT DIAGRAMS
The layout or design of the system must be thoroughly documented in an As-Built diagram. Refer to the
following examples of acceptable As-Built symbols and As-Built diagram samples:
As-Built Diagram Symbols

TPD-5201-G 05-13-11
Page 21

As-Built Diagram Example

TPD-5201-G 05-13-11
Page 22


TPD-5201-G 05-13-11
Page 23

IN ROOM DOCUMENTATION AND READINGS

Documenting TV Types
To ensure that the LodgeNet or On Command system can be properly installed and or configured, all of
the different TV hardware combinations must be documented. Refer to the following sample TV Type
Legend:
Type #
1
2
3
4
Make
Model #
TV Type Legend
Terminal / Commander
Remote Control
Additional TV types Type # rows can be added if needed to document all of the different hardware
combinations being installed.
TVs should be listed by both manufacturer and model number.
If a LodgeNet terminal or Commander is installed with the TV, the terminal or Commander model
number should be documented in the matrix.
If a LodgeNet or On Command remote control is installed with the TV, the remote control model
number should be documented in the matrix.
Documenting RF Room Readings

RF readings must be taken at each TV location to ensure the MATV system has been installed correctly
and will adequately support a LodgeNet Guest Pay or Free-To-Guest system. Refer to the following
sample Room Reading matrix:
Room #
TV
Type
Notes
Tap
Value
50.5
Highest
Rack Ch.#
Highest Ch. =
Inserted
Channel #
Ch. 78 (550 MHz) /

Ch. 116 (750 MHz) /
Ch. 135 (860 MHz)
Return
The Room # column should be used to document the room that the readings were taken from.
If more than one TV will be installed in a room or suite, readings should be taken at each TV
location. The room number should then include some designation to identify the location within the
room. Example = 100LR for room 100 Living Room or 100BR for room 100 Bed Room.
The TV Type column should be used to document the TV configuration installed at each TV location.
The TV Types should correspond to the TV types documented in the TV Type matrix.
The Notes column should be used to document anything of special interest at that particular TV
location.
The Tap Value column should be used to document the wall tap value at each TV location. If a
particular TV location is a home run, document it as a home run.

TPD-5201-G 05-13-11
Page 24

The 50.5 column should be used to document the RF readings taken at 50.5 MHz for each of the TV
locations. Please note that a modulator will need to be inserted and balanced at this frequency to take
the readings.
At the top of the Highest Rack Channel column, the person taking the readings should indicate the
highest channel that will be used on the MATV system at the time of installation. If this information
is not known, it can be obtained by contacting LodgeNet. This column will then be used to document
the RF readings taken at the Highest Rack Channel for each of the TV locations. Please note that a
modulator will need to be inserted and balanced at this frequency to take the readings.
At the top of the Inserted Channel # column, the person taking the RF readings should indicate the
highest channel supported by the MATV system (this can be indicated by circle the highest channel).
This column will then be used to document the RF readings taken at the Inserted Channel # for each
of the TV locations. Please note that a modulator will need to be inserted and balanced at this
frequency to take the readings.
The Return column should be used to document the RF level of the return signals from the TV
location back to the headend location. The return signals should be 5 MHz35 MHz at 36 dBmV
reference. These readings only need to be documented from a few rooms fed from each distribution
amplifier (middle room / middle riser).
All room readings must meet the requirements outlined in the Signal Specifications section of this
document.
ADDITIONAL INFORMATION
For additional MATV information, questions, or MATV design, please contact the LodgeNet Professional
Solutions Group at 1-888-LODGENET or at professionalsolutions@lodgenet.com.

TPD-5201-G 05-13-11
Page 25


CATV Lodget Hotel

Uploaded by

Document Informationclick to expand document informationManual de consejos y datos tecnicos para instalaciones de cctv en hoteles

Document Informationclick to expand document information

Copyright:

Available Formats

CATV Lodget Hotel

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CATV Lodget Hotel

Uploaded by

Copyright:

Available Formats

LODGENET HOTEL INSTALLATION

Copyright 2011 LodgeNet Interactive Corporation. All Rights Reserved.

SECTION 1: LODGENET GUEST PAY AND FREE-TO-GUEST REQUIREMENTS _________ 4

SECTION 2: CATV/MATV DISTRIBUTION REQUIREMENTS _________________________ 11

SECTION 3: DOCUMENTATION OF SYSTEM DESIGN AND PERFORMANCE __________ 21

LodgeNet Hotel Installation Overview

LodgeNet Confidential - Use and Distribution

LODGENET HOTEL INSTALLATION OVERVIEW

DOCUMENT PURPOSE & DEFINITION

LodgeNet Hotel Installation Overview

LodgeNet Confidential - Use and Distribution

SECTION 1: LODGENET GUEST PAY AND FREE-TO-GUEST

FTG HARDWARE COMPONENTS

LodgeNet Hotel Installation Overview

LodgeNet Confidential - Use and Distribution

RACK ROOM REQUIREMENTS

Applications Wizard Dimensions (Can be located outside the rack room):

Network Printer Dimensions (Can be located outside the rack room):

LodgeNet Hotel Installation Overview

LodgeNet Confidential - Use and Distribution

Electrical Circuit Requirements

SYSTEM HVAC REQUIREMENTS

LodgeNet Confidential - Use and Distribution

FTG HVAC REQUIREMENTS

For More Channels

RACK ROOM CABLING REQUIREMENTS

LodgeNet Hotel Installation Overview

LodgeNet Confidential - Use and Distribution

Guest Pay System Cabling Diagram

SATELLITE DISH REQUIREMENTS

LodgeNet Hotel Installation Overview

LodgeNet Confidential - Use and Distribution

LodgeNet Hotel Installation Overview

LodgeNet Confidential - Use and Distribution

GUEST ROOM REQUIREMENTS

LodgeNet Hotel Installation Overview

LodgeNet Confidential - Use and Distribution

SECTION 2: CATV/MATV DISTRIBUTION REQUIREMENTS

The recommended MATV/CATV distribution systems forward frequency response must be at 49

DISTRIBUTION CLOSET REQUIREMENTS

Must be a secure, limited access area.

Max Output @ Max Input

LodgeNet Hotel Installation Overview

LodgeNet Confidential - Use and Distribution

DE-RATED AMPLIFIER INPUT/OUTPUT SPECIFICATIONS

High Gain (43 dBmV) Cascaded Amplifier Input/Output Specifications

PASSIVE DEVICE REQUIREMENTS

LodgeNet Hotel Installation Overview

LodgeNet Confidential - Use and Distribution

Cable Specification Chart

18 AWG Copper-Clad Steel.

Riser Rated RG-6

Shielding Type and Coverage

Jacket Type and Thickness

Foil: Aluminum/Poly tap 100% coverage

Flame Retardant PVC. Nom.

Maximum Cable Attenuation Chart (dB/100 ft.)

Maximum Cable Attenuation Chart (dB/100 ft.)