Scribd
Upload
83 views2 pages

Enetwork Basic Configuration PT Practice Sba: Step 1: Determine The Ip Addressing Scheme

The document provides instructions for configuring basic network connectivity between two PCs via a router and switch. It includes an addressing table to be filled in determining the IP addressing scheme for devices on subnet 172.16.1.0/24. The tasks involve configuring Router1 and Switch1 interfaces, IP addresses for devices, and verifying end-to-end connectivity between PC1 and PC2 by pinging between them. Any errors are to be troubleshot if the ping fails.

Uploaded by

Madalina Georgiana Hahue
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
83 views2 pages

Enetwork Basic Configuration PT Practice Sba: Step 1: Determine The Ip Addressing Scheme

The document provides instructions for configuring basic network connectivity between two PCs via a router and switch. It includes an addressing table to be filled in determining the IP addressing scheme for devices on subnet 172.16.1.0/24. The tasks involve configuring Router1 and Switch1 interfaces, IP addresses for devices, and verifying end-to-end connectivity between PC1 and PC2 by pinging between them. Any errors are to be troubleshot if the ping fails.

Uploaded by

Madalina Georgiana Hahue
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

ENetwork Basic Configuration PT Practice SBA

A few things to keep in mind while completing this activity:


1. Do not use the browser Back button or close or reload any exam windows during the exam.
2. Do not close Packet Tracer when you are done. It will close automatically.
3. Click the Submit Assessment button to submit your work.

Introduction
In this practice Packet Tracer Skills Exam, you will:

design and implement an addressing scheme to meet stated requirements

configure, verify, and troubleshoot connectivity between all devices in the network

Addressing Table
Device

Interface

Address

Subnet Mask

Default Gateway

Fa0/0

Router1

Fa0/1

Switch1

VLAN1

PC1

NIC

PC2

NIC

n/a
172.16.1.33

255.255.255.240

n/a

Preconfigured

Preconfigured

Preconfigured

NOTE: The initial network has some errors. To aid in configuring and verifying the devices, as well as
in troubleshooting the existing errors, use a printed version of these instructions to fill in the missing
address information in the table during Step 1.

Step 1: Determine the IP Addressing Scheme.


Design an addressing scheme and fill in the Addressing Table based on the following requirements:
a. Subnet the address space 172.16.1.0/24 to provide 30 host addresses for LAN 1 while
wasting the least amount of address space.
b. Assign the first available subnet to LAN 1.
c. Assign the lowest (first) host address in this subnet to the Fa0/0 interface on Router1.
d. Assign the second address in this subnet to the VLAN 1 interface on Switch1.
e. Assign the highest (last) host IP address in this subnet to PC1.

Step 2: Configure Router1.


a. Configure Router1 with these basic parameters:

Use Router1 as the router name.

Use class as the encrypted password for privileged EXEC mode.

Require password-protected logins for the console line. Use cisco as the password.

Require password-protected logins for the vty lines. Use cisco as the password.

Configure the banner message-of-the-day as Authorized access only!

b. Configure the two Fast Ethernet interfaces.

Configure the router interfaces according to your completed addressing table.

Configure each interface with a description.

c. Close the terminal window after completing the router configuration.

Step 3: Configure Switch1 and Verify Connectivity.


a. Remove the console connection between PC1 and Router1.
b. Connect PC1 to the Switch1 console port.
c. Configure Switch1 with these basic parameters:

Use Switch1 for the switch name.

Use class as the encrypted password for privileged EXEC mode.

Require password-protected logins for the console line. Use cisco as the password.

Require password-protected logins for the vty lines. Use cisco as the password.

Configure the banner message-of-the-day as Authorized access only!

d. Configure interface VLAN 1.


e. Configure the default gateway.
f. Test that Switch1 is able to ping the default gateway.

Step 4: Configure and Verify PC1 Addressing.


a. Use the IP addressing you determined in Step 1 and configure PC1 with the correct
addressing.
b. Test that PC1 is able to ping the default gateway.

Step 5: Verify and Troubleshoot End-to-End Connectivity.


Verify that PC1 is able to ping PC2. If the ping fails, locate and correct any errors. For example, make
sure PC2 is configured correctly with appropriate addressing for the subnet it belongs to.

You might also like