Footwear - Stocking Frames

18th Century Material Culture
Stocking Frames
Stocking
Production
History of the Hand Knitting Frame

(German Hosiery Museum)
Mechanical hosiery knitting began in the 16th century and the method carried
on into the 19th century almost unchanged.
William Lee, a theology student from Woodborough near Nottingham, built a
mechanical hand knitting frame in 1598, which was the first attempt at
mechanizing hosiery knitting. From this time on, it was possible to hand-knit
stockings with mechanical help.
Lee's knitting frame, fully constructed using iron, was an upright chair fitted
with a bench for the knitter. Lee's first knitting frame could form 600 stitches
per minute, as opposed to a practiced hand-knitter, who could only form about
100 stitches.

Queen Elizabeth I. prohibited the patent which would have been necessary to
produce mechanically-knit stockings and allow Lee to distribute his knitting
frame throughout England. Her explanation was that the knitting frame could
only produce coarse woolen goods which could not compete with fine handknit silk stockings. The real reason, though, was probably the fear that
hundreds of hand-knitters would be unemployed if Lee's knitting frame were
launched.
Lee attempted to establish his now improved "machine" in London in 1609.
His knitting frame could meanwhile produce silk stockings with 1500 stitches
per minute. Again, his patent application was rejected.

With the help of the Duke of Sully, minister of King Henry IV. of France, Lee
established his knitting frame in Rouen in 1612. Lee agreed to deliver 8
machines to Rouen, and send 6 English knitters to teach the French how to
produce hosiery mechanically. Lee was apparently working in Rouen with
another two Englishmen in 1615, but this was the last mention of him - he
probably died in France. After William Lee's death, his brother James brought
seven of the knitting frames and most of the English knitters back to England,
where the knitting frame was improved in the 1620's. Instead of the original
fineness of 12 gauge (12gg - this means 12 needles per 1.5 inches, or 3,81 cm),
stockings with 24 gauge fineness could be produced. Other improvements
most likely led to the fact that now only one knitter could operate the knitting
frame, as opposed to two knitters for the original knitting frame.

n 1641, there were two stocking knitting master craftsmen in Nottingham, who
produced stockings on an unknown number of knitting frames. Most of
England's knitting frames, though, could be found in London near the King's
Court - the largest consumer of hosiery. In 1660, there were 650 knitting frames
in England, 400 of them in London. By 1695, the number of knitting frames in
London increased to 1500, and between 1670 and 1695, an additional 400
knitting frames were exported to France, Italy and Spain. This happened
although King Charles II. ordered an export embargo for all knitting frames
with which silk stockings could be produced in 1663.

The knitting frame continued to be improved. At the end of the 17th century,
the knitting method and thus the mesh structure became smoother. This made
England the leading producer of knit stockings, which were in demand all over
Europe. Knit stockings were one of England's most important exports during
this time.

James Lee brought 7 of the 8 knitting frames in Rouen back to England - the
8th knitting frame ended up in Venice with its English knitter. There it was
copied and distributed to various European cities. Around 1700, one of the
knitting frames could be found in Dresden, where it was used by a Frenchman.
Johann Esche, who's father operated a dyeing mill in Limbach near Chemnitz,
had the opportunity to see a knitting frame while purchasing stockings. After
several visits and in-depth studies of its construction, Esche was able to
reproduce the knitting frame in wood. Esche opened a hosiery mill, and with
his reproduction of knitting frame, a flourishing hosiery industry was founded
in the Erz Mountains.
1589
William Lee from Woodborough, Nottingham, invents the first Hand
Knitting Machine or Frame. With his invention, smooth, unpatterned,
stockings could be produced with 600 stitches per minute and a fineness of 12
gauge (12 needles per 1.5 inches/3.81 cm).
1609
Lee's knitting frame is improved to 1500 stitches per minute and a fineness of
24 gauge.

1658
Industrial spy, Jean Hindret, smuggles design drawings of William Lee's
knitting frame to France. These drawings would eventually be published a
century later in Denis Diderots Encyclopedia.
In 1667, Hindret opens the first Royal silk hosiery mill in France. Originally
located in the Chteau de Madrid in Bois de Boulogne near Paris, it would
later spawn other mills throughout the French countryside. To control this,
the French Government issues a royal decree in 1700 which limits the
production of silk hosiery to Paris, Dourdan, Rouen, Cannes, Nantes, Olron,
Aix-en-Provence, Toulouse, Uzes, Romans, Lyon, Metz, Bourges, Poitiers,
Orleans, Amiens, Reims and Nmes.

During the beginning of the 18th century - when the hand knitting frame
became known throughout France and Germany - the knitting frames, which
were originally made from steel, were reproduced in wood in Wrttemberg
and the Erz Mountains and renamed roller chairs. Many of the parts of Lee's
knitting frame, which were originally made from steel, were fabricated from
wood in Germany due to the shortage of steel workers and of steel itself. The
steel hand knitting frame was not introduced in Germany until 1770.
In 1740, due to the introduction of the pressing machine, the production of
stockings with colored pressed patterns became possible.
1758
English Hosier Jedediah Strutt from Derby, and his brother-in-law, William
Woollatt, receives a patent by adapting Lees Stocking Frame with an
attachment to produce commercially available, mass-produced, Ribbed
Stockings.
Called Ribbed Goods or Derby-Ribs in England, this double-faced fabric
(which were arguably more form fitting or elastic than plain knit stockings)
becomes a major competitor to those goods made possible only by handknitting.
Hosier Jedediah Strutt

by Joseph Wright of Derby c. 1787
(Derby Museums & Art Gallery)

1763
English Hosier, John Morris, patents a frame that allows the production of
eyelet hole mesh.
Used extensively for border lace, mitts and gloves,
handkerchiefs, and hoods and caps, it also enabled ornamental pierced
patterns to be placed in the clocks of stockings. This Point net Machine gave
birth to the Nottingham Lace Industry.
Lace Made on a Stocking Frame

(Nottingham City Museums)
1776
English workman, William Brockey of Nottingham, creates a frame to
produce Twilled or Plated goods (diagonal parallel raised ribs). Now, the
outside of a knitted article could be composed of a dierent yarn than that on
the inside. This gave birth to the production of silk stockings with an inner
lining of cotton.

TWILL
Twill is a type of textile weave with a pattern of diagonal parallel ribs (in
contrast with a satin and plain weave). This is done by passing the weft thread
over one or more warp threads and then under two or more warp threads and
so on, with a "step" or oset between rows to create the characteristic diagonal
pattern. Because of this structure, twills generally drape well. (Wikipedia)
History of the
Mechanical Flat Knitting Frame
As opposed to hand-knitting, where stitches are formed one-by-one with
moving latch needles, machine-knitting produces a row of stitches with the
help of bearded needles and hooks. (Machine-knitting procedure).
The construction of mechanical knitting frames can be retraced into the 18th
century - the hand knitting frame was the basis. At first, the hand knitting
frame was furnished with a revolving shaft and fitted with levers and cams - the
whole contraption was then built into the base of the knitting frame. The
machine was powered using a crankshaft, which was operated either by hand
or through transmittal of elemental power. With the availability of water and
steam power, the factory production of warp-knit and later knit stockings
began.
History of the
At first, only products with uniform widths could be produced using

mechanical knitting frames. Single pieces of the basic commodity had to be cut
out from the produced piece goods and then sewn together. Stockings
produced by this method were cheaper, but the fit was not optimal. Therefore,
stockings produced with the hand knitting frame - where stockings were
narrowed according to the leg shape - were considered the better product in
comparison to machine-knit stockings for a long time.
History of the
1769
Englishman Samuel Wise patents rotary-driven frame to allow for the
production of stockings with narrower stitching. His flat bed invention utilized
a revolving shaft built into the base frame which was set into motion by an
elemental power source. It would become the predecessor of the mechanical
rotary frame machine put into use until the end of the 19th century.
German Hosiery Production

1698
The Art of Stocking-Frame-Work-Knitting, engraved for the 'Universal Magazine'

by English School 1750
(The British Museum)
The Stocking Frame and other Apparatus used in the Manufactory

A NEW AND COMPLETE DICTIONARY OF ARTS AND SCIENCES... by A SOCIETY OF GENTLEMEN 1763
(Getty Research Institute)



French Stocking Knitters

Diderot's Encyclopdie 1751
Stocking Loom
The Encyclopedia of Diderot & d'Alembert 1763
(University of Michigan)
Stocking Loom
Stocking Loom
Stocking Loom
Stocking Loom
Stocking Loom
Stocking Loom
Stocking Loom
Stocking Loom
Production of Loom - Made Stockings




English Stocking Frame

by J. Clee after Thomas Sandby 1751
English Stocking Frame

by J. Clee after Thomas Sandby 1751
Wooden Hand-Knitting frame, Based on Lee's System, 17th Century

In Germany, the Machine was widely distributed under the name "Rsschen-Stuhl". ("Little Horse Knitting Frame")
Hand Knitting Frame Copper Etching

18th century
English Stocking Frame or Knitting Machine

c. 1740
(Leicestershire County Council)

c. 1740
(Leicestershire County Council)

c. 1775 - 1820
(Colonial Williamsburg)
Wooden "Rsschen-Stuhl" ("Little Horse Knitting Frame")

18th century
Stocking Frame
c. 1770
(Science Museum / Science & Society)
Improved Hand Knitting Frame

18th century
Hand Knitting Frame

Brought Hawick by John Hardie in 1771 - 1798
(Tower Mill, Hawick)
Coat of Arms of the first English Hosiery Knitter Cooperative

William Lee, His Wife, & His Hand Knitting Machine
A Stocking Maker
by Samuel Okey after Bartolome Estevan Murillo c. 1760
Acknowledgements
The Narration on Stocking Frames was taken word for word from the website
put out by the German Hosiery Museum (http://www.german-hosierymuseum.de/hosiery-museum.htm)
Acknowledgements
The material contained within these slideshows is presented for educational purposes only. The
18th Century Material Culture Resource Center does not personally own any of the items
depicted herein and is indebted to the countless museums, libraries, and private collectors who
willingly share their collections with the public through the internet. Every attempt has been
made to credit these organizations and individuals for their contributions as best as possible.
If there is a question you have regarding a particular item featured within a presentation, please
contact the 18th Century Material Culture Resource Center and we will try to answer your
inquiry as best as possible. If for any reason you feel there is any item that should not be
presented here, or if there is an error in any listing, or if you know the source for any item whose
credit is unknown, please inform us and we will make sure your concern is addressed as soon as
possible.
Thank you!
- The 18th Century Material Culture Resource Center

Footwear - Stocking Frames

Uploaded by

Copyright:

Available Formats

Footwear - Stocking Frames

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Footwear - Stocking Frames

Uploaded by

Copyright:

Available Formats

18th Century Material Culture

History of the Hand Knitting Frame

History of the Hand Knitting Frame

History of the Hand Knitting Frame

History of the Hand Knitting Frame

History of the Hand Knitting Frame

History of the Hand Knitting Frame

History of the Hand Knitting Frame

History of the Hand Knitting Frame

History of the Hand Knitting Frame

History of the Hand Knitting Frame

Hosier Jedediah Strutt

History of the Hand Knitting Frame

Lace Made on a Stocking Frame

History of the Hand Knitting Frame

History of the Hand Knitting Frame

At first, only products with uniform widths could be produced using

German Hosiery Production

The Art of Stocking-Frame-Work-Knitting, engraved for the 'Universal Magazine'

The Stocking Frame and other Apparatus used in the Manufactory

The Stocking Frame and other Apparatus used in the Manufactory

The Stocking Frame and other Apparatus used in the Manufactory

The Stocking Frame and other Apparatus used in the Manufactory

French Stocking Knitters

Production of Loom - Made Stockings

Production of Loom - Made Stockings

Production of Loom - Made Stockings

Production of Loom - Made Stockings

English Stocking Frame

English Stocking Frame

Wooden Hand-Knitting frame, Based on Lee's System, 17th Century

Hand Knitting Frame Copper Etching

English Stocking Frame or Knitting Machine

English Stocking Frame or Knitting Machine

English Stocking Frame or Knitting Machine

Wooden "Rsschen-Stuhl" ("Little Horse Knitting Frame")

Improved Hand Knitting Frame

Hand Knitting Frame

Coat of Arms of the first English Hosiery Knitter Cooperative

You might also like