Pump Handbook Complete

GRUNDFOS INDUSTRY
PUMP HANDBOOK
Being responsible is our foundation

Thinking ahead makes it possible
Innovation is the essence
Poul Due Jensens Vej 7

DK-8850 Bjerringbro
Tel: +45 87 50 14 00
www.grundfos.com
96563258 1104
GRUNDFOS Management A/S
PUMP HANDBOOK
Copyright 2004 GRUNDFOS Management A/S. All rights reserved.

Copyright law and international treaties protect this material. No part of this material
may be reproduced in any form or by any means without prior written permission from
GRUNDFOS Management A/S.
Disclaimer
All reasonable care has been taken to ensure the accuracy of the contents of this material,
however GRUNDFOS Management A/S shall not be reliable for any loss whether direct,
indirect, incidental or consequential arising out of the use of or reliance upon any of the
content of the material.
Foreword
The manufacturing industry places heavy demand on pumps, when it comes to
optimum operation, high reliability and low energy consumption. Therefore,
Grundfos has developed the Pump handbook, which in a simple manner deals
with various considerations when dimensioning pumps and pump systems.
We have elaborated a handbook for engineers and technicians who work with
design and installation of pumps and pump systems, containing answers to a
wide range of technical pump specic questions. The Pump handbook can either
be read from one end to the other or partly on specic topics.
The handbook is divided into 5 chapters which deal with different phases when
designing pump systems.
Throughout chapter 1 we make a general presentation of different pump types
and components. Here we also describe which precautions to adopt when dealing
with viscous liquids. Further, the most used materials as well as different types of
corrosion are presented here. The most important terminologies in connection
with reading the pump performance are presented in chapter 2. Chapter 3 deals
with system hydraulics and some of the most important factors to consider to obtain
optimum operation of the pump system. As it is often necessary to adjust the pump
performance by means of different adjustment methods, these are dealt with in
chapter 4. Chapter 5 describes the life cycle costs as energy consumption plays an
important role in todays pumps and pump systems.
We sincerely hope that you will make use of The pump handbook and nd it useful in
your daily work.
Segment Director
Business Development Manager
Allan Skovgaard
Claus Brnholdt Nielsen
Table of Contents
Chapter 1 Design of pumps and motors ......................7
Section 1.1 Pump construction ............................................................ 8

1.1.1 The centrifugal pump .................................................................. 8
1.1.2 Pump curves................................................................................................9
1.1.3 Characteristics of the centrifugal pump ......................... 11
1.1.4 Most common end-suction and
in-line pump types .............................................................................. 12
1.1.5 Impeller types (axial forces) .......................................................14
1.1.6 Casing types (radial forces) ......................................................... 15
1.1.7 Single-stage pumps ........................................................................... 15
1.1.8 Multistage pumps ...............................................................................16
1.1.9 Long-coupled and close-coupled pumps ........................16
Section 1.2 Types of pumps ...................................................................17
1.2.1 Standard pumps .................................................................................... 17
1.2.2 Split-case pumps .................................................................................. 17
1.2.3 Hermetically sealed pumps ........................................................18
1.2.4 Sanitary pumps ..................................................................................... 20
1.2.5 Wastewater pumps............................................................................ 21
1.2.6 Immersible pumps ..............................................................................22
1.2.7 Borehole pumps ....................................................................................23
1.2.8 Positive displacement pumps ...................................................24
Section 1.3 Mechanical shaft seals ..................................................27
1.3.1 The mechanical shaft seals
components and function............................................................29
1.3.2 Balanced and unbalanced shaft seals .............................. 30
1.3.3 Types of mechanical shaft seals ............................................. 31
1.3.4 Seal face material combinations ...........................................34
1.3.5 Factors affecting the seal performance ...........................36
Section 1.4 Motors .................................................................................... 39
1.4.1 Standards.................................................................................................... 40
1.4.2 Motor start-up ....................................................................................... 46
1.4.3 Voltage supply ........................................................................................47
1.4.4 Frequency converter ..........................................................................47
1.4.5 Motor protection ................................................................................. 49
Section 1.5 Liquids .......................................................................................53

1.5.1 Viscous liquids ........................................................................................54
1.5.2 Non-Newtonian liquids .................................................................. 55
1.5.3 The impact of viscous liquids on the
performance of a centrifugal pump.................................... 55
1.5.4 Selecting the right pump for a liquid
with antifreeze .......................................................................................56
1.5.5 Calculation example..........................................................................58
1.5.6 Computer aided pump selection for dense and
viscous liquids .........................................................................................58
Section 1.6 Materials................................................................................ 59
1.6.1 What is corrosion?.............................................................................. 60
1.6.2 Types of corrosion................................................................................61
1.6.3 Metal and metal alloys ...................................................................65
1.6.4 Ceramics ....................................................................................................... 71
1.6.5 Plastics............................................................................................................ 71
1.6.6 Rubber ............................................................................................................ 72
1.6.7 Coatings ........................................................................................................ 73
Chapter 2 Installation and performance

reading.............................................................................................................75
Section 2.1 Pump installation ............................................................ 76
2.1.1 New installation ....................................................................................76
2.1.2 Existing installation-replacement ........................................76
2.1.3 Pipe ow for single-pump installation ............................. 77
2.1.4 Limitation of noise and vibrations .......................................78
2.1.5 Sound level (L) .........................................................................................81
Section 2.2 Pump performance ........................................................ 83
2.2.1 Hydraulic terms .....................................................................................83
2.2.2 Electrical terms ...................................................................................... 90
2.2.3 Liquid properties ...................................................................................93
Chapter 3 System hydraulic .................................................... 95
Chapter 5 Life cycle costs calculation
Section 3.1 System characteristics .................................................96

3.1.1 Single resistances .................................................................................97
3.1.2 Closed and open systems ............................................................ 98
Section 5.1 Life cycle costs equation ............................................ 128

5.1.1 Initial costs, purchase price (Cic) ........................................... 129
5.1.2 Installation and commissioning costs (Cin) ................ 129
5.1.3 Energy costs (Ce) ................................................................................. 130
5.1.4 Operating costs (Co) ......................................................................... 130
5.1.5 Environmental costs (Cenv) ......................................................... 130
5.1.6 Maintenance and repair costs (Cm)..................................... 131
5.1.7 Downtime costs, loss of production (Cs) ....................... 131
5.1.8 Decommissioning and disposal costs (Co) ................... 131
Section 3.2 Pumps connected in series and parallel...................101

3.2.1 Pumps in parallel ................................................................................101
3.2.2 Pumps connected in series ....................................................... 103
Chapter 4 Performance adjustment

of pumps..................................................................................................... 105
Section 4.1 Adjusting pump performance ..............................106
4.1.1 Throttle control ....................................................................................107
4.1.2 Bypass control .......................................................................................107
4.1.3 Modifying impeller diameter ................................................. 108
4.1.4 Speed control ........................................................................................ 108
4.1.5 Comparison of adjustment methods...............................110
4.1.6 Overall efciency of the pump system ........................... 111
4.1.7 Example: Relative power consumption
when the ow is reduced by 20%........................................ 111
Section 4.2 Speed-controlled pump solutions .................... 114
4.2.1 Constant pressure control..........................................................114
4.2.2 Constant temperature control ............................................... 115
4.2.3 Constant differential pressure in a
circulating system ............................................................................. 115
4.2.4 Flow-compensated differential
pressure control ...................................................................................116
Section 4.3 Advantages of speed control .................................117
Section 4.4 Advantages of pumps with integrated
frequency converter............................................................................... 118
4.4.1 Performance curves of speed-controlled
pumps ...........................................................................................................119
4.4.2 Speed-controlled pumps in different systems ........119
Section 4.5 Frequency converter .................................................... 122
4.5.1 Basic function and characteristics ......................................122
4.5.2 Components of the frequency converter .....................122
4.5.3 Special conditions regarding frequency
converters ................................................................................................124
....................... 127
Section 5.2 Life cycle costs calculation

an example ................................................................................................132
Appendix .........................................................................................................133
A)
Notations and units .........................................................................134
B)
Unit conversion tables...................................................................135
C)
SI-prexes and Greek alphabet ............................................ 136
D)
Vapour pressure and density of water at
different temperatures .................................................................137
E)
Orice ..........................................................................................................138
F)
Change in static pressure due to change
in pipe diameter ................................................................................. 139
G)
Nozzles ........................................................................................................ 140
H)
Nomogram for head losses in
bends, valves, etc. ..............................................................................141
I)
Pipe loss nomogram for clean water 20C ..................142
J)
Periodical system................................................................................143
K)
Pump standards ................................................................................. 144
L)
Viscosity for different liquids as a function
of liquid temperature....................................................................145
Index ..................................................................................................................151
Index
A
Absolute pressure
Adjusting pump performance
Aluminium
Asynchronous motor
ATEX (ATmosphre EXplosible)
Austenitic (non-magnetic)
Autotransformer starting
Axial ow pumps
Axial forces
85
106
70
40
41
68
46
8
14
B
Balanced shaft seal
Basic coupling
Bearing
Insulated bearing
Bellows seal
Borehole pump
Bypass control
30
16
51
48
31
23
106
Speed control
Constant differential pressure control
Constant pressure control
Constant temperature control
Copper alloys
Corrosion
Cavitation corrosion
Corrosion fatigue
Crevice corrosion
Erosion corrosion
Galvanic corrosion
Intergranular corrosion
Pitting corrosion
Selective corrosion
Stress corrosion cracking (SCC)
Uniform corrosion
Corrosion fatigue
Coupling
Basic coupling
Flexible coupling
Spacer coupling
Crevice corrosion
108
115
114
115
69
60
63
64
62
63
64
62
61
62
63
61
64
16
16
16
16
62
C
Canned motor pump
Cartridge seal
Casing
Double-volute
Single-volute
Return channel
Cast iron
Cavitation
Centrifugal pump
Ceramics
Close-coupled pump
Closed system
Coatings
Metallic coatings
Non-metallic coatings
Organic coatings
Computer aided pump selection
Control
Throttle control
Bypass control
18
32
15
15
15
15
66
10, 89
63
8
71
12, 13, 16
96, 98
73
73
74
74
58
106
107
107
D
Decommissioning and disposal costs
131
Deep well pump
23
Density
10, 93
Unit
Appendix A
Water
Appendix D
Brine
Appendix L
Diaphragm pump
25
Differential pressure
88
Differential pressure control
116
Dilatant liquid
55
Direct-on-line starting (DOL)
46
Dosing pump
25
Double mechanical shaft seal
33
Double seal in tandem
33
Double seal in back-to-back
34
Double-channel impeller
21
Double-inlet
17
Double-suction impeller
11, 17
Double-volute casing
15
Downtime costs
131
Index
Dust ignition proof (DIP)

Duty point
Dynamic pressure
Dynamic viscosity
Index
42
96
84
54
E
Earth-leakage circuit breaker (ELCB)
Efciency
Efciency at reduced speed
Efciency curve
Electric motor
Flameproof motor
Increased safety motor
Non-sparking motor
EMC directive
EMC lter
Enclosure class (IP), motor
End-suction pump
Energy costs
Energy savings
Environmental costs
Erosion corrosion
Ethylene propylene rubber (EPDM)
Expansion joints
125
10
109
10
40
41
41
42
123
123
43
12
130
111, 114, 117
130
63
72
80
F
Ferritic (magnetic)
68
Ferritic-austenitic or duplex (magnetic)
68
Ferrous alloys
65
Flameproof motor
41
Flexible coupling
16
Floating plinth
79
Flow
83
Mass ow
83
Volume ow
83
Units
Appendix B
Fluoroelastomers (FKM)
72
Flushing
32
Foundation
78
Floating plinth
79
Floor
79
Plinth
79
Vibration dampeners
79
Frame size
Frequency converter
44
47, 108, 118
G
Galvanic corrosion
Gauge pressure
Geodetic head
Geodetic lift
Grey iron
64
85
99
99
66
H
Head
Heat capacity
Hermetically sealed pump
Horizontal pump
Hydraulic power
9, 85
93
18
12, 13
10, 91
I
IEC, motor
Immersible pump
Impeller
Double-channel
Single-channel
Vortex impeller
Increased safety motor
Initial costs
In-line pump
Installation and commissioning costs
Insulation class
40
22
14, 21
21
21
21
41
129
12, 13
129
44
62
K
Kinematic viscosity
54, Appendix L
L
Life cycle costs
Example
Liquid
Dilatant
Newtonian
Non-Newtonian
Plastic uid
Thixotrophic
Viscous
Long-coupled pump
Loss of production costs
N
117, 128
132
54
55
55
55
55
55
54
12, 13, 16
131
40
55
69
72
66
78
74
55
124
42
10, 89
M
Magnetic drive
Maintenance and repair costs
Martensitic (magnetic)
Mass ow
Measuring pressure
Mechanical shaft seal
Bellows seal
Cartridge seal
Metal bellows seal
Rubber bellows seal
Function
Flushing
Metal alloys
Ferrous alloys
Metal bellows seal
Metallic coatings
Mixed ow pumps
Modifying impeller diameter
Motors
Motor efciency
Motor insulation
Motor protection
Motor start-up
Star/delta starting
Frequency converter
Soft starter
Mounting of motor (IM)
Multistage pump
NEMA, motor standard

Newtonian uid
Nickel alloys
Nitrile rubber
Nodular iron
Noise (vibration)
Non-Newtonian liquid
Non-sinusoidal current
Non-sparking motor
NPSH (Net Positive Suction Head)
19
131
68
83
85
18, 28
31
32
32
31
29
32
65
65
32
73
8
108, 110
40
49
48
49
46
46
46
46
46, 47
46
43
11, 12, 13, 16
Open system
Operating costs
Organic coatings
O-ring seal
Oversized pumps
96, 99
106, 130
74
31
106
P
Paints
Peruoroelastomers (FFKM)
Phase insulation
PI-controller
Pitting corrosion
Plastic uid
Plastics
Plinth
Positive displacement pump
Power consumption
Hydraulic power
Shaft power
Pressure
Absolute pressure
Differential pressure
Dynamic pressure
Gauge pressure
Measuring pressure
Static pressure
System pressure
Units
Vapour pressure
74
72
48
114
61
55
71
79
24
10, 91
10, 91
91
84
85
88
84
85
85
84
88
85, Appendix A
90, Appendix D
Index
Pressure control
Constant differential pressure control
115
Constant pressure
114
Constant pressure control
119
Constant supply pressure
114
Pressure transmitter (PT)
114
Proportional pressure control
120
PTC thermistors
50
Pulse Width Modulation (PWM)
123
Pump
Axial ow pump
8
Borehole pump
23
Canned motor pump
18
Centrifugal pump
8
Close-coupled pump
12, 13, 16
Diaphragm pump
25
Dosing pump
25
Hermetically sealed pump
18
Horizontal pump
12, 13
Immersible pump
22
Long-coupled pump
12, 13, 16
Magnetic-driven pump
19
Mixed ow pump
8
Multistage pump
11, 12, 13, 16
Positive displacement pump
24
Radial ow pump
8
Sanitary pump
20
Single-stage pump
15
Split-case pump
12, 13, 17
Standard pump
17
Vertical pump
12, 13
Wastewater pump
21
Pump casing
15
Pump characteristic
9, 96
Pump curve
9
Pump installation
77
Pump performance curve
9, 96
Pumps connected in series
103
Pumps in parallel
101
Pumps with integrated frequency converter 118
Purchase costs
129
PWM (Pulse Width Modulation)
123
Index
Q
QH-curve
R
Radial ow pump
Radial forces
Reinforced insulation
Resistances connected in parallel
Resistances connected in series
Return channel casing
Rubber
Ethylene propylene rubber (EPDM)
Nitrile rubber (NBK)
Peruoroelastomers (FFKM)
Silicone rubber (Q)
Rubber bellows seal
8
15
48
98
97
11, 15
72
72
72
72
72
72
31
S
Sanitary pump
Seal face
Seal gab
Selective corrosion
Setpoint
Shaft
Shaft power
Shaft seal
Balanced shaft seal
Unbalanced shaft seal
Silicone rubber (Q)
Single resistances
Single-channel impeller
Single-stage pump
Single-suction impeller
Single-volute casing
Soft starter
Sound level
Sound pressure level
Spacer coupling
20
28
29
62
114
11
91
28
30
30
72
97
97
21
11, 12, 13, 15
11
15
46
81
82
16
Speed control
106, 108, 110
Variable speed control
108
Speed-controlled pumps in parallel
102
Split-case pump
12, 13, 17
Stainless steel
66
Standard pump
17
Standards
40
IEC, motor
40
NEMA, motor
40
Sanitary standards
20
Standstill heating of motor
51
Star/delta starting
46
Static pressure
84
Steel
65
63
Stufng box
28
Submersible pump
23
System characteristic
96
Closed system
96, 98
Open system
96, 99
System costs
117
System pressure
88
T
Temperature
Units
Thermoplastics
Thermosets
Thixotrophic liquid
Throttle control
Throttle valve
Titanium
Twin pump
93
Appendix B
71
71
55
106, 110-113
107
70
11
U
Uniform corrosion
30
61
V
Vapour pressure
Variable speed control
Vertical pump
Vibration dampeners
Vibrations
Viscosity
Dynamic viscosity
Viscous liquid
Viscous liquid pump curve
Voltage supply
Volume ow
Units
Volute casing
Vortex impeller
Wastewater pump
90, Appendix D
108
12, 13
79
78
54, Appendix L
54
54
55
47
83
Appendix A
11
21
21
Chapter 1. Design of pumps and motors
Section 1.1: Pump construction

1.1.1
1.1.2
1.1.3
1.1.4
1.1.5
1.1.6
1.1.7
1.1.8
1.1.9
The centrifugal pump

Pump curves
Characteristics of the centrifugal pump
Most common end-suction and in-line
pump types
Impeller types (axial forces)
Casing types (radial forces)
Single-stage pumps
Multistage pumps
Long-coupled and close-coupled pumps
Section 1.2: Types of pumps

1.2.1
1.2.2
1.2.3
1.2.4
1.2.5
1.2.6
1.2.7
1.2.8
Standard pumps
Split-case pumps
Hermetically sealed pumps
Sanitary pumps
Wastewater pumps
Immersible pumps
Borehole pumps
Positive displacement pumps
Section 1.1
Pump construction
1.1.1 The centrifugal pump

In 1689 the physicist Denis Papin invented the centrifugal
pump and today this kind of pump is the most used around
the world. The centrifugal pump is built on a simple
principle: Liquid is led to the impeller hub and by means
of the centrifugal force it is flung towards the periphery of
the impellers.
The construction is fairly inexpensive, robust and simple
and its high speed makes it possible to connect the pump
directly to an asynchronous motor. The centrifugal pump
provides a steady liquid flow, and it can easily be throttled
without causing any damage to the pump.
Now let us have a look at figure 1.1.1, which shows the
liquids flow through the pump. The inlet of the pump
leads the liquid to the centre of the rotating impeller from
where it is flung towards the periphery. This construction
gives a high efficiency, and is suitable for handling pure
liquids. Pumps, which have to handle impure liquids, such
as wastewater pumps, are fitted with an impeller that is
constructed especially to avoid that objects get stocked
inside the pump, see section 1.2.5.
Fig. 1.1.1: The liquids flow through the pump
Radial flow pump
Mixed flow pump
Axial flow pump
Fig. 1.1.2: Different kinds of centrifugal pumps
If a pressure difference occurs in the system while the

centrifugal pump is not running, liquid can still pass
through it due to its open design.
As you can tell from figure 1.1.2, the centrifugal pump can
be categorised in different groups: Radial flow pumps,
mixed flow pumps and axial flow pumps. Radial flow
pumps and mixed flow pumps are the most common
types used. Therefore, we will only concentrate on these
types of pumps on the following pages.
H
[m]
104
6
4
2
Multistage radial
flow pumps
103
6
4
2
102
However, we will briefly present the positive displacement

pump in section 1.2.8.
Single-stage radial
flow pumps
6
4
2
101
The different demands on the centrifugal pumps

performance, especially with regards to head, flow, and
installation, together with the demands for economical
operation, are only a few of the reasons why so many types
of pump exist. Figure 1.1.3 shows the different pump types
with regard to flow and pressure.
Mixed flow pumps
6
4
2
Axial flow pumps
4 6 101 2
4 6 10
4 6 103 2
4 6 104 2
4 6 10
Q [m3/s]
Fig. 1.1.3: Flow and head for different types of centrifugal pumps
1.1.2 Pump curves

Before we dig any further into the world of pump
construction and pump types, we will present the
basic characteristics of pump performance curves. The
performance of a centrifugal pump is shown by a set
of performance curves. The performance curves for a
centrifugal pump are shown in figure 1.1.4. Head, power
consumption, efficiency and NPSH are shown as a function
of the flow.
[%]
H
[m]
50
40
70
30
Efficiency
50
20
40
10
20
30
10
0
P2
[kW]
10
20
30
40
50
60
70
Q [m /h]
3
NPSH
(m)
12
Power consumption
10
Normally, pump curves in data booklets only cover the

pump part. Therefore, the power consumption, the P2value, which is listed in the data booklets as well, only
covers the power going into the pump see figure 1.1.4.
The same goes for the efficiency value, which only covers
the pump part ( = P).
60
10
8
6
4
NPSH
Fig. 1.1.4: Typical performance curves for a centrifugal

pump. Head, power consumption, efciency and NPSH
are shown as a function of the ow
Q
In some pump types with integrated motor and possibly
integrated frequency converter, e.g. canned motor pumps
(see section 1.2.3), the power consumption curve and the
-curve cover both the motor and the pump. In this case it
is the P1-value that has to be taken into account.
In general, pump curves are designed according to ISO
9906 Annex A, which specifies the tolerances of the
curves:
Q +/- 9%,
H +/-7%,
P +9%
-7%.
What follows is a brief presentation of the different pump

performance curves.
P1
M
3~
P2
Fig. 1.1.5: The curves for power consumption and efciency will
normally only cover the pump part of the unit i.e. P2 and P
H
[m]
60
50
40
30
Head, the QH-curve
20
10
The QH-curve shows the head, which the pump is able

to perform at a given flow. Head is measured in meter
liquid column [mLC]; normally the unit meter [m] is
applied. The advantage of using the unit [m] as the unit
of measurement for a pumps head is that the QH-curve is
not affected by the type of liquid the pump has to handle,
see section 2.2 for more information.
10
20
30
40
50
60
70
80 Q [m3/h]
Fig. 1.1.6: A typical QH-curve for a centrifugal pump;

low ow results in high head and high ow results
in low head
Section 1.1
Pump construction
Efficiency, the -curve

The efficiency is the relation between the supplied power
and the utilised amount of power. In the world of pumps,
the efficiency P is the relation between the power, which
the pump delivers to the water (PH) and the power input
to the shaft (P2 ):
p =
PH
.g.Q.H
=
P2
P2
where:
is the density of the liquid in kg/m3,
g is the acceleration of gravity in m/s2,
Q is the flow in m3/s and H is the head in m.
[%]
80
70
60
50
40
30
20
For water at 20oC and with Q measured in m3/h and H in m,

the hydraulic power can be calculated as :
PH = 2.72 . Q . H [W]
10
0
0
10
20
30
40
50
60
70
Q [m3/h]
Fig. 1.1.7: The efciency curve of a typical centrifugal pump
As it appears from the efficiency curve, the efficiency depends

on the duty point of the pump. Therefore, it is important to
select a pump, which fits the flow requirements and ensures
that the pump is working in the most efficient flow area.
P2
[kW]
Power consumption, the P2-curve
10
8
6
4
The relation between the power consumption of the pump

and the flow is shown in figure 1.1.8. The P2-curve of most
centrifugal pumps is similar to the one in figure 1.1.8 where
the P2 value increases when the flow increases.
NPSH-curve (Net Positive Suction Head)

The NPSH-value of a pump is the minimum absolute
pressure (see section 2.2.1) that has to be present at the
suction side of the pump to avoid cavitation.
The NPSH-value is measured in [m] and depends on the
flow; when the flow increases, the NPSH-value increases
as well; figure 1.1.9. For more information concerning
cavitation and NPSH, go to section 2.2.1.
10
2
0
0
10
20
30
40
50
60
70
Q [m3/h]
Fig. 1.1.8: The power consumption curve of a typical

centrifugal pump
NPSH
[m]
10
8
6
4
2
0
0
10
20
30
40
50
60
70
Q [m3/h]
Fig. 1.1.9: The NPSH-curve of a typical centrifugal pump
1.1.3 Characteristics of the

centrifugal pump
The centrifugal pump has several characteristics and in
this section, we will present the most important ones.
Later on in this chapter we will give a more thorough
description of the different pump types.
The number of stages

Depending on the number of impellers in the pump, a
centrifugal pump can be either a single-stage pump or a
multistage pump.
The position of the pump shaft

Single-stage and multistage pumps come with horizontal
or vertical pump shafts. These pumps are normally
designated horizontal or vertical pumps. For more
information, go to section 1.1.4.
Single-suction or double-suction impellers

Depending on the construction of the impeller, a pump can
be fitted with either a single-suction impeller or a doublesuction impeller. For more information, go to section 1.1.5.
Coupling of stages
The pump stages can be arranged in two different ways: in
series and in parallel, see figure 1.1.10.
Construction of the pump casing

We distinguish between two types of pump casing: Volute
casing and return channel casing with guide vanes. For
more information, go to section 1.1.6.
Fig 1.1.10: Twin pump with parallel-coupled impellers
11
Section 1.1
Pump construction
1.1.4 Most common end-suction and in-line pump types
End-suction
Horizontal
Single-stage
Long-coupled
12
Multistage
Close-coupled
Close-coupled
End-suction pump
The liquid runs directly into the impeller. Inlet and outlet have a
90 angle. See section 1.1.9
In-line pump
The liquid runs directly through the pump in-line. The suction pipe and the discharge
pipe are placed opposite one another and can be mounted directly in the piping system
Split-case pump
Pump with an axially divided pump housing. See section 1.2.2
Horizontal pump
Pump with a horizontal pump shaft
Vertical pump
Pump with a vertical pump shaft
Single-stage pump
Pump with a single impeller. See section 1.1.7
Multistage pump
Pump with several series-coupled stages. See section 1.1.8
Long-coupled pump
Pump connected to the motor by means of a flexible coupling. The motor and
the pump have separate bearing constructions. See section 1.1.9
Close-coupled pump
A pump connected to the motor by means of a rigid coupling. See section 1.1.9
In-line
Horizontal
Horizontal / Vertical
Split-case
Single-stage
Multistage
Single-stage
Long-coupled
Long-coupled
Close-coupled
Close-coupled
13
Section 1.1
Pump construction
1.1.5 Impeller types (axial forces)

A centrifugal pump generates pressure that exerts forces
on both stationary and rotating parts of the pump.
Pump parts are made to withstand these forces.
If axial and radial forces are not counterbalanced in the
pump, the forces have to be taken into consideration when
selecting the driving system for the pump (angular contact
bearings in the motor). In pumps fitted with single-suction
impeller, large axial forces may occur, figures 1.1.11 and
1.1.12. These forces are balanced in one of the following
ways:
Axial forces
Fig. 1.1.11: Single-suction

impeller
Fig. 1.1.12: Standard pump with

single-suction impeller
Mechanically by means of thrust bearings. These types

of bearings are specially designed to absorb the axial
forces from the impellers
By means of balancing holes on the impeller,
see figure 1.1.13
Fig. 1.1.13: Balancing the axial forces

in a single-stage centrifugal pump
with balancing holes only
By means of throttle regulation from a seal ring

mounted on the back of the impellers, see figure 1.1.14
Dynamic impact from the back of the impeller, see
figure 1.1.15
Fig. 1.1.14: Balancing the axial forces

in a single-stage centrifugal pump
with sealing gap at discharge side and
balancing holes
The axial impact on the pump can be avoided by either

using double-suction impellers (see figure 1.1.16).
Fig. 1.1.15: Balancing the axial forces in
a single-stage centrifugal pump with
blades on the back of the impellers
Fig. 1.1.16: Balancing the axial

forces in a double-suction
impeller arrangement
14
1.1.6 Casing types (radial forces)
Fig. 1.1.17: Single-suction

impeller
Radial forces
Radial forces are a result of the static pressure in the

casing. Therefore, axial deflections may occur and lead
to interference between the impeller and the casing. The
magnitude and the direction of the radial force depend on
the flow rate and the head.
Fig. 1.1.18: Single-volute casing
Double-volute casing
Radial force
When designing the casing for the pump, it is possible

to control the hydraulic radial forces. Two casing types
are worth mentioning: the single-volute casing and the
double-volute casing. As you can tell from figure 1.1.18,
both casings are shaped as a volute. The difference between
them is, that the double-volute has an guide vane.
The single-volute pump is characterised by a symmetric
pressure in the volute at the optimum efficiency point,
which leads to zero radial load. At all other points,
the pressure around the impeller is not regular and
consequently a radial force is present.
As you can tell from figure 1.1.19, the double-volute casing
develops a constant low radial reaction force at any capacity.
Return channels (figure 1.1.20) are used in multistage pumps
and have the same basic function as volute casings. The
liquid is led from one impeller to the next and at the same
time, the rotation of water is reduced and the dynamic
pressure is transformed into static pessure. Because of the
return channel casings circular design, no radial forces are
present.
Volute casing
Double-volute
casing
1.0
Q/Qopt
Fig. 1.1.19: Radial force for single- and double-volute casing
Fig. 1.1.20: Vertical multistage

in-line pump with return
channel casing
Return channel
1.1.7 Single-stage pumps

Generally, single-stage pumps are used in applications,
which do not require a total head of more than 150 m.
Normally, single-stage pumps operate in the interval of
2-100 m.
Single-stage pumps are characterised by providing a low
head relative to the flow, see figure 1.1.3. The single-stage
pump comes in both a vertical and a horizontal design, see
figures 1.1.21 and 1.1.22.
Fig. 1.1.21: Horizontal single-stage

end-suction close-coupled pump
Fig. 1.1.22: Vertical single-stage

in-line close-coupled pump
15
Section 1.1
Pump construction
1.1.8 Multistage pumps

Multistage pumps are used in installations where a high
head is needed. Several stages are connected in series and
the flow is guided from the outlet of one stage to the inlet
of the next. The final head that a multistage pump can
deliver is equal to the sum of pressure each of the stages
can provide.
The advantage of multistage pumps is that they provide
high head relative to the flow. Like the single-stage pump,
the multistage pump is available in both a vertical and a
horizontal version, see figures 1.1.23 and 1.1.24.
Fig. 1.1.23: Vertical

multistage in-line pump
Fig. 1.1.24: Horizontal multistage

end-suction pump
Fig. 1.1.25: Long-coupled pump

with basic coupling
Fig. 1.1.26: Long-coupled pump with spacer coupling
1.1.9 Long-coupled and close-coupled

pumps
Long-coupled pumps
Long-coupled pumps are pumps with a flexible coupling
that connects the pump and the motor. This kind of
coupling is available either as a basic coupling or as a
spacer coupling.
If the pump is connected to the motor by a basic coupling,
it is necessary to dismount the motor when the pump
needs service. Therefore, it is necessary to align the pump
upon mounting, see figure 1.1.25.
On the other hand, if the pump is fitted with a spacer
coupling, it is possible to service the pump without
dismounting the motor. Alignment is thus not an issue,
see figure 1.1.26.
Close-coupled pumps
Close-coupled pumps can be constructed in the following
two ways: Either the pump has the impeller mounted
directly on the extended motor shaft or the pump has a
standard motor and a rigid or a spacer coupling, see figures
1.1.27 and 1.1.28.
16
Fig. 1.1.27: Close-coupled pump with

rigid coupling
Fig. 1.1.28: Different coupling types
Basic coupling
type
Long-coupled
pump with
flexible coupling
Close-coupled
pump with
rigid coupling
Spacer coupling
(option)
Section 1.2
Types of pumps
1.2.1 Standard pumps

Few international standards deal with centrifugal pumps.
In fact, many countries have their own standards, which
more or less overlap one another. A standard pump is
a pump that complies with official regulations as to for
example the pumps duty point. What follows, are a couple
of examples of international standards for pumps:
Fig. 1.2.1: Long-coupled standard pump
EN 733 (DIN 24255) applies to end-suction centrifugal

pumps, also known as standard water pumps with a
rated pressure (PN) of 10 bar.
EN 22858 (ISO 2858) applies to centrifugal pumps, also
known as standard chemical pumps with a rated
pressure (PN) of 16 bar, see appendix K.
The standards mentioned above cover the installation
dimensions and the duty points of the different pump
types. As to the hydraulic parts of these pump types, they
vary according to the manufacturer thus, no international
standards are set for these parts.
Fig. 1.2.2: Bare shaft standard pump
Pumps, which are designed according to standards, provide

the end-user with advantages with regard to service, spare
parts and maintenance.
1.2.2 Split-case pumps

A split-case pump is a pump with the pump housing
divided axially into two parts. Figure 1.2.4 shows a singlestage split-case pump with a double-suction impeller.
The double-inlet construction eliminates the axial
forces and ensures a longer life span of the bearings.
Usually, split-case pumps have a rather high efficiency,
are easy to service and have a wide performance range.
Fig. 1.2.3: Long-coupled split-case pump
Fig. 1.2.4: Split-case pump

with double-suction impeller
17
Section 1.2
Types of pumps
Liquid
1.2.3 Hermetically sealed pumps
Seal
Atmosphere
It comes as no surprise that a pumps shaft lead-in has to be

sealed. Usually, this is done by means of a mechanical shaft
seal, see figure 1.2.5. The disadvantage of the mechanical
shaft seal is its poor properties when it comes to handling
of toxic and aggressive liquids, which consequently leads
to leakage. These problems can to some extent be solved
by using a double mechanical shaft seal. Another solution
to these problems is to use a hermetically sealed pump.
We distinguish between two types of hermetically sealed
pumps: Canned motor pumps and magnetic-driven pumps.
In the following two sections, you can find additional
information about these pumps.
Fig. 1.2.5: Example of a standard pump with mechanical shaft seal
Canned motor pumps

A canned motor pump is a hermetically sealed pump with
the motor and pump integrated in one unit without a seal,
see figures 1.2.6 and 1.2.7. The pumped liquid is allowed to
enter the rotor chamber that is separated from the stator
by a thin rotor can. The rotor can serves as a hermetically
sealed barrier between the liquid and the motor. Chemical
pumps are made of materials, e.g. plastics or stainless
steel that can withstand aggressive liquids.
Motor can
Fig. 1.2.6: Chemical pump with canned motor
The most common canned motor pump type is the

circulator pump. This type of pump is typically used in
heating circuits because the construction provides low
noise and maintenance-free operation.
Motor can
Fig. 1.2.7: Circulator pump

with canned motor
18
Magnetic-driven pumps
In recent years, magnetic-driven pumps have become
increasingly popular for transferring aggressive and toxic
liquids.
Outer magnets
Inner magnets
Can
As shown in figure 1.2.8, the magnetic-driven pump is

made of two groups of magnets; an inner magnet and
an outer magnet. A non-magnetizable can separate these
two groups. The can serves as a hermetically sealed barrier
between the liquid and the atmosphere. As it appears
from figure 1.2.9, the outer magnet is connected to the
pump drive and the inner magnet is connected to the
pump shaft. Hereby the torque from the pump drive is
transmitted to the pump shaft. The pumped liquid serves
as lubricant for the bearings in the pump. Therefore,
sufficient venting is crucial for the bearings.
Fig. 1.2.8: Construction of magnetic drive
Inner magnets
Outer magnets
Can
Fig. 1.2.9: Magnetic-driven multistage pump
19
Section 1.2
Types of pumps
1.2.4 Sanitary pumps

Sanitary pumps are mainly used in the food, beverage,
pharmaceutical and bio-technological industries where it
is important that the pumped liquid is handled in a gentle
manner and that the pumps are easy to clean.
In order to meet process requirements in these industries,
the pumps have to have a surface roughness between
3.2 and 0.4 m Ra. This can be best achieved by using
forged or deep-drawn rolled stainless steel as materials
of construction, see figure 1.2.12. These materials have a
compact pore-free surface finish that can be easily worked
up to meet the various surface finish requirements.
Fig. 1.2.10: Sanitary pump
The main features of a sanitary pump are ease of cleaning

and ease of maintenance.
The leading manufacturers of sanitary pumps have
designed their products to meet the following standards:
EHEDG European Hygienic Equipment Design Group

QHD
Qualified Hygienic Design
3-A
Sanitary Standards:
3A0/3A1: Industrial/Hygienic Standard
Ra 3.2 m
3A2: Sterile Standard
Ra 0.8 m
3A3: Sterile Standard
Ra 0.4 m
Fig.1.2.11: Sanitary self-priming side-channel pump
Sand casting
Precision casting
Rolled steel
Fig.1.2.12: Roughness of material surfaces
20
1.2.5 Wastewater pumps

A wastewater pump is an enclosed unit with a pump
and a motor. Due to this construction the wastewater
pump is suitable for submersible installation in pits.
In submersible installations with auto-coupling systems
double rails are normally used. The auto-coupling system
facilitates maintenance, repair and replacement of the
pump. Because of the construction of the pump, it is
not necessary to enter the pit to carry out service. In
fact, it is possible to connect and disconnect the pump
automatically from the outside of the pit. Wastewater
pumps can also be installed dry like conventional pumps
in vertical or horizontal installations. Likewise this type of
installation provides easy maintenance and repair like it
provides uninterrupted operation of the pump in case of
flooding of the dry pit, see figure 1.2.14.
Fig.1.2.13: Detail of a sewage pump

for wet installations
Normally, wastewater pumps have to be able to handle large

particles. Therefore they are fitted with special impellers that
make it possible to avoid blockage and clogging. Different
types of impellers exist; single-channel impellers, doublechannel impellers three and four-channel impellers and
vortex impellers. Figure 1.2.15 shows the different designs of
these impellers.
Wastewater pumps usually come with a dry motor, which
is IP68 protected (for more information on IP-classes,
go to section 1.4.1). Motor and pump have a common
extended shaft with a double mechanical shaft seal system
in an intermediate oil chamber, see figure 1.2.13.
Wastewater pumps are able to operate either intermittently
or continuously depending on the installation in question.
Fig. 1.2.14: Wastewater pump for dry installations
Vortex
impeller
Single-channel
impeller
Double-channel
impeller
Fig. 1.2.15: Impeller types for wastewater
21
Section 1.2
Types of pumps
1.2.6 Immersible pumps

An immersible pump is a pump type where the pump part
is immersed in the pumped liquid and the motor is kept
dry. Normally, immersible pumps are mounted on top of
or in the wall of tanks or containers. Immersible pumps
are for example used in the machine tool industry for
example in spark machine tools, grinding machines,
machining centres and cooling units or in other industrial
applications involving tanks or containers, such as
industrial washing and filtering systems.
Pumps for machine tools can be divided in two groups:
Pumps for the clean side of the filter and pumps for the
dirty side of the filter. Pumps with closed impellers are
normally used for the clean side of the filter, because they
provide a high efficiency and a high pressure if necessary.
Pumps with open or semi-open impellers are normally
used for the dirty side of the filter, because they can
handle metal chips and particles.
Fig. 1.2.16: Immersible pump
22
1.2.7 Borehole pumps

Two types of borehole pumps exist: The submerged
borehole pump type with a submersible motor, and the
deep well pump with a dry motor, which is connected
to the pump by a long shaft. These pumps are normally
used in connection with water supply and irrigation. Both
pump types are made to be installed in deep and narrow
boreholes and have thus a reduced diameter, which makes
them longer than other pump types, see figure 1.2.17.
The borehole pumps are specially designed to be
submerged in a liquid and are thus fitted with a
submersible motor, which is IP68 protected. The pump
comes in both a single-stage and a multistage version (the
multistage version being the most common one), and is
fitted with a non-return valve in the pump head.
Today, the deep well pump has been more or less replaced
by the submerged pump type. The long shaft of the deep
well pump is a drawback, which makes it difficult to
install and carry out service. Because the deep well pump
motor is air-cooled, the pump is often used in industrial
applications to pump hot water from open tanks. The
submersible pump cannot handle as high temperatures
because the motor is submerged in the liquid, which has
to cool it.
Fig. 1.2.17: Submersible pump
23
Section 1.2
Types of pumps
1.2.8 Positive displacement pumps
Fig. 1.2.18: Typical relation between

flow and head for 3 different pump types:
1) Centrifugal pumps
2) Rotary pumps
3) Reciprocating pumps
The positive displacement pump provides an approximate

constant flow at fixed speed, despite changes in the
counterpressure. Two main types of positive displacement
pumps exist:
1
H
Rotary pumps
Reciprocating pumps
The difference in performance between a centrifugal
pump, a rotary pump and a reciprocating is illustrated
to the right, figure 1.2.18. Depending on which of these
pumps you are dealing with, a small change in the pumps
counterpressure results in differences in the flow.
The flow of a centrifugal pump will change considerably,
the flow of a rotary pump will change a little, while the
flow of a reciprocating pump will hardly change at all.
But, why is there a difference between the pump curves
for reciprocating pumps and rotary pumps? The actual
seal face surface is larger for rotary pumps than for
reciprocating pumps. So, even though the two pumps are
designed with the same tolerances, the gap loss of the
rotary pump is larger.
The pumps are typically designed with the finest tolerances

possible to obtain the highest possible efficiency and
suction capability. However, in some cases, it is necessary
to increase the tolerances, for example when the pumps
have to handle highly viscous liquids, liquids containing
particles and liquids of high temperature.
Positive displacement pumps are pulsate, meaning that
their volume flow within a cycle is not constant.
The variation in flow and speed leads to pressure fluctuations
due to resistance in the pipe system and in valves.
Diaphragm
Steam
Plunger
Power
Double-acting
Double-acting
Duplex
Flexible member
Screw
Gear
Multiple rotor
Lobe
Circumferential piston
Fig. 1.2.19: Classification of positive displacement pumps
24
Duplex
Simplex
Piston
Rotary
Simplex
Single-acting
Vane
Single rotor
Reciprocating
Positive
displacement
pumps
Screw
Triplex
Multiplex
Dosing pumps
The dosing pump belongs to the positive displacement
pump family and is typically of the diaphragm type. Diaphragm
pumps are leakage-free, because the diaphragm forms
a seal between the liquid and the surroundings.
The diaphragm pump is fitted with two non-return valves
one on the suction side and one on the discharge side
of the pump. In connection with smaller diaphragm pumps,
the diaphragm is activated by the connecting rod, which is
connected to an electromagnet. Thereby the coil receives
the exact amount of strokes needed, see figure 1.2.21.
In connection with larger diaphragm pumps the
diaphragm is typically mounted on the connecting rod,
which is activated by a camshaft. The camshaft is turned by
means of a standard asynchronous motor, see figure 1.2.22.
The flow of a diaphragm pump is adjusted by either
changing the stroke length and/or the frequency of the
strokes. If it is necessary to enlarge the operating area,
frequency converters can be connected to the larger
diaphragm pumps, see figure 1.2.22.
Fig.1.2.21: Solenoid spring return
Yet, another kind of diaphragm pump exists. In this case,

the diaphragm is activated by means of an excentrically
driven connecting rod powered by a stepper motor or a
synchronous motor, figures 1.2.20 and 1.2.23. By using a
stepper motor drive the pumps dynamic area is increased
and its accuracy is improved considerably. With this
construction it is no longer necessary to adjust the pumps
stroke length because the connection rod is mounted
directly on the diaphragm. The result is optimised suction
conditions and excellent operation features.
Fig. 1.2.20: Dosing pump
1.2.22: Cam-drive spring return
So therefore, it is simple to control both the suction

side and the discharge side of the pump. Compared to
traditional electromagnetic-driven diaphragm pumps
which provide powerful pulsations, stepper motor-driven
diaphragm pumps make it possible to get a much more
steady dosage of additive.
1.2.23: Crank drive
25
Section 1.3: Mechanical shaft seals

1.3.1 The mechanical shaft seals components
and function
1.3.2 Balanced and unbalanced shaft seals
1.3.3 Types of mechanical shaft seals
1.3.4 Seal face material combinations
1.3.5 Factors affecting the seal performance
Section 1.3
Mechanical shaft seals
From the middle of the 1950s mechanical shaft seals

gained ground in favour of the traditional sealing method
- the stuffing box. Compared to stuffing boxes, mechanical shaft seals provide the following advantages:
They keep tight at smaller displacements and vibrations

in the shaft
They do not require any adjustment

Seal faces provide a small amount of friction and thus,
minimise the power loss
The shaft does not slide against any of the seals

components and thus, is not damaged because of
wear (reduced repair costs).
The mechanical shaft seal is the part of a pump that
separates the liquid from the atmosphere. In figure 1.3.1
you can see a couple of examples where the mechanical
shaft seal is mounted in different types of pumps.
The majority of mechanical shaft seals are made
according to the European standard EN 12756.
Before choosing a shaft seal, there are certain things
you need to know about the liquid and thus the
seals resistance to the liquid:
Determine the type of liquid

Determine the pressure that the shaft seal is exposed to
Determine the speed that the shaft seal is exposed to
Determine the built-in dimensions
On the following pages we will present how a mechanical shaft
seal works, the different types of seal, which kind of materials
mechanical shaft seals are made of and which factors that
affect the mechanical shaft seals performance.
28
Fig. 1.3.1: Pumps with mechanical shaft seals
1.3.1 The mechanical shaft seals

components and function
The mechanical shaft seal is made of two main components:
a rotating part and a stationary part; and consists of the parts
listed in figure 1.3.2. Figure 1.3.3 shows where the different
parts are placed in the seal.
The stationary part of the seal is fixed in the pump
Designation
Rotating part
Secondary seal
Spring
Seal face (primary seal)
Spring retainer (torque transmission)

Stationary part
Seat (seal faces, primary seal)

Static seal (secondary seal)
Fig. 1.3.2: The mechanical shaft seals components
housing. The rotating part of the seal is fixed on the

pump shaft and rotates when the pump operates.
The two primary seal faces are pushed against each other
by the spring and the liquid pressure. During operation
a liquid film is produced in the narrow gap between the
two seal faces. This film evaporates before it enters the
atmosphere, making the mechanical shaft seal liquid tight,
see figure 1.3.4.
Spring
Secondary seal
Primary seal
Stationary part
Rotating part
Spring retainer
Shaft
Secondary seals prevent leakage from occurring

between the assembly and the shaft.
The spring presses the seal faces together mechanically.
Secondary seal
Fig. 1.3.3: Main components of the

mechanical shaft seal
The spring retainer transmits torque from the shaft to
Vapour
the seal. In connection with mechanical bellows shaft

seals, torque is transferred directly through the bellows.
Primary seal
Evaporation
begins
Lubrication film
Liquid force
Spring force
Seal gap
During operation the liquid forms a lubricating film
between the seal faces. This lubricating film consists of a
hydrostatic and a hydrodynamic film.
Fig. 1.3.4: Mechanical shaft seal in operation
The hydrostatic element is generated by the pumped

liquid which is forced into the gap between the seal faces.
The hydrodynamic lubricating film is created by

pressure generated by the shafts rotation.
29
Section 1.3
Start of
evaporation
1 atm
Exit into
atmosphere
1.3.2 Balanced and unbalanced shaft seals

To obtain an acceptable face pressure between the
primary seal faces, two kind of seal types exist: a balanced
shaft seal and an unbalanced shaft seal.
Stationary
seal face
Rotating
seal face
Pump pressure
Entrance
in seal
Pressure
Liquid
Vapour
Atmosphere
Fig. 1.3.5: Optimum ratio between fine lubrication

properties and limited leakage
Balanced shaft seal

Figure 1.3.6 shows a balanced shaft seal indicating where
the forces interact on the seal.

The thickness of the lubricating film depends on the pump
speed, the liquid temperature, the viscosity of the liquid
and the axial forces of the mechanical shaft seal. The
liquid is continuously changed in the seal gap because of
evaporation of the liquid to the atmosphere
Figure 1.3.7 shows an unbalanced shaft seal indicating

where the forces interact on the seal.
Contact area of seal faces
Contact area of seal faces

Spring forces
Hydraulic forces
Hydraulic forces
the liquids circular movement

A
Figure 1.3.5 shows the optimum ratio between fine

lubrication properties and limited leakage. As you can tell,
the optimum ratio is when the lubricating film covers the
entire seal gap, except for a very narrow evaporation zone
close to the atmospheric side of the mechanical shaft seal.
Leakage due to deposits on the seal faces is often observed.
When using coolant agents, deposits are built up quickly by
the evaporation at the atmosphere side of the seal. When
the liquid evaporates in the evaporation zone, microscopic
solids in the liquid remain in the seal gap as deposits
creating wear.
These deposits are seen in connection with most types
of liquid. But when the pumped liquid has a tendency
to crystallise, it can become a problem. The best way to
prevent wear is to select seal faces made of hard material,
such as tungsten carbide (WC) or silicon carbide (SiC).
The narrow seal gap between these materials (app. 0.3 m
Ra) minimises the risk of solids entering the seal gap and
thereby minimises the amount of deposits building up.
30
Fig. 1.3.6: Interaction of

forces on the balanced
shaft seal
Fig. 1.3.7: Interaction of

forces on the unbalanced
shaft seal
Several different forces have an axial impact on the seal

faces. The spring force and the hydraulic force from the
pumped liquid press the seal together while the force from
the lubricating film in the seal gap counteracts this. In
connection with high liquid pressure, the hydraulic forces
can be so powerful that the lubricant in the seal gap cannot
counteract the contact between the seal faces. Because the
hydraulic force is proportionate to the area that the liquid
pressure affects, the axial impact can only be reduced by
obtaining a reduction of the pressure-loaded area.
Wear rate comparative
20
40
60
The balancing ratio (K) of a mechanical shaft seal is defined

as the ratio between the area A and the area (B) : K=A/B
80
100
120
140
Wear rate
comparative
o
Temperature ( C)
K = 1.15
K = 1.00
K = 0.85
K = Balancing ratio
A = Area exposed to hydraulic pressure
B = Contact area of seal faces
For balanced shaft seals the balancing ratio is usually
around K=0.8 and for unbalanced shaft seals the balancing
ratio is normally around K=1.2.
0
20
40
60
80
100
Fig. 1.3.8: Wear rate for different balancing ratios
120
140
Temperature (oC)
K = 1.15
1.3.3 Types of mechanical shaft seals
K = 1.00
K = 0.85
What follows is a brief outline of the main types of

mechanical shaft seals: O-ring seal, bellows seal, and the
one-unit seal - the cartridge seal.
Fig. 1.3.9: O-ring seal

Advantages and
disadvantages of
O-ring seal
O-ring seals
In an O-ring seal, sealing between the rotating shaft and
the rotating seal face is effected by an O-ring (figure 1.3.9).
The O-ring must be able to slide freely in the axial direction
to absorb axial displacements as a result of changes
in temperatures and wear. Incorrect positioning of the
stationary seat may result in rubbing and thus unnecessary
wear on the O-ring and on the shaft. O-rings are made of
different types of rubber material, such as NBR, EPDM and
FKM, depending on the operating conditions.
Bellows seals
A common feature of bellows seals is a rubber or metal
bellows which functions as dynamic sealing element
between the rotating ring and the shaft.
Rubber bellows seals

The bellows of a rubber bellows seal (see figure 1.3.10) can
be made of different types of rubber material, such as NBR,
EPDM and FKM, depending on the operating conditions.
Two different geometric principles are used for the
design of rubber bellows:
Folding bellows
Rolling bellows.
Advantages:
Suitable in hot liquid and
high pressure applications
Disadvantages:
Deposits on the shaft,
such as rust, may prevent
the O-ring shaft
seal from moving axially
Rubber bellows seal with folding

bellows geometry
Fig. 1.3.10: Rubber bellows seal

Advantages and
disadvantages of
rubber bellows seal
Advantages:
Not sensitive to deposits,
such as rust, on the shaft
Suitable for pumping
solid-containing liquids
Disadvantages:
Not suitable in hot liquid and
high pressure applications
31
Section 1.3
Advantages and
disadvantages of cartridge
metal bellows seal
Metal bellows seals

In an ordinary mechanical shaft seal, the spring produces
the closing force required to close the seal faces. In a
metal bellows seal (figure 1.3.11) the spring has been
replaced by a metal bellows with a similar force.
Metal bellows act both as a dynamic seal between the
rotating ring and the shaft and as a spring. The bellows
have a number of corrugations to give them the desired
spring force.
Advantages:
Not sensitive to deposits,
such as rust and lime on
the shaft
Suitable in hot liquid and
high-pressure applications
Low balancing ratio leads
to low wear rate and
consequently longer life
Fig. 1.3.11: Cartridge metal
bellows seal
Disadvantages:
Fatique failure of the
mechanical shaft seal may
occur when the pump is not
aligned correctly
Fatique may occur as a
result of excessive
temperatures or pressures
Cartridge seals
Advantages of the
cartridge seal:
In a cartridge mechanical shaft seal, all parts form a compact

unit on a shaft sleeve, ready to be installed. A cartridge seal
offers many benefits compared to conventional mechanical
shaft seals, figure 1.3.12.
Easy and fast service

The design protects the
seal faces
Preloaded spring
Safe handling
Flushing
In certain applications it is possible to extend the
performance of the mechanical shaft seal by installing
flushing, see figure 1.3.13. Flushing can lower the
temperature of the mechanical shaft seal and prevent
deposits from occurring. Flushing can be installed either
internally or externally. Internal flushing is done when a
small flow from the pumps discharge side is bypassed
to the seal area. Internal flushing is primarily used to
prevent further heat generation from the seal in heating
applications. External flushing is done by a flushing liquid
and is used to ensure trouble-free operation when handling
liquids that are abrasive or contain clogging solids.
32
Fig. 1.3.12: Cartridge seal
Fig 1.3.13: Flushing device of a

single mechanical shaft seal
Double mechanical shaft seals

Double mechanical shaft seals are used when the life
span of single mechanical shaft seals is insufficient due
to wear caused by solids or too high/low pressure and
temperature. Further, double mechanical shaft seals are
used in connection with toxic, aggressive and explosive liquids
to protect the surroundings. Two types of double mechanical
shaft seals exist: The double seal in a tandem arrangement
and the double seal in a back-to-back arrangement.
Quench liquid
Quench liquid
Quench liquid
Pumped liquid
Double seal in tandem

This type of double seal consists of two mechanical shaft
seals mounted in tandem, that is one behind the other,
placed in a separate seal chamber, see figure 1.3.14.
Pumped liquid
Pumped Tandem
liquid
Fig. 1.3.14:
seal arrangement with quench liquid
circulation
The seal type is used when a pressurised double mechanical

shaft seal mounted in a back-to-back arrangement is not
necessary.
The tandem seal arrangement has to be fitted with a
quenching liquid system which
Quench liquid
Quench liquid
absorbs leakage
monitors the leakage rate
lubricates and cools the outboard seal to prevent icing
protects against dry-running
stabilises the lubricating film
prevents air from entering the pump in case of vacuum
The pressure of the quenching liquid must always be lower

than the pumped liquid pressure.
Quench liquid
Pumped liquid
Pumped liquid
Pumped liquid
Fig. 1.3.15: Tandem seal arrangement with quench liquid dead

end
Tandem - circulation
Circulation of quenching liquid via a pressureless tank, see
figure 1.3.14. Quenching liquid from the elevated tank is
circulated by thermosiphon action and/or by pumping action
in the seal.
Tandem - dead end

Quenching liquid from an elevated tank, see figure 1.3.15. No
heat is dissipated from the system.
Pumped
liquid
Pumped
liquid
Pumped
liquid
Tandem - drain
The quenching liquid runs directly through the seal chamber
to be collected for reuse, or directed to drain, see figure 1.3.16.
Fig. 1.3.16: Tandem seal arrangement with quench liquid to drain
33
Section 1.3
Barrier pressure liquid
Seal chamber with

barrier pressure liquid
1.3.4 Seal face material combinations

What follows is a description of the most important
material pairings used in mechanical shaft seals for
industrial applications: Tungsten carbide/tungsten
carbide, silicon carbide/silicon carbide and carbon/
tungsten carbide or carbon/silicon carbide.
Pumped liquid
Tungsten carbide/tungsten carbide

(WC/WC)
Fig. 1.3.17:
Back-to-back seal arrangement
Double seal in back-to-back

This type of seal is the optimum solution for handling
abrasive, aggressive, explosive or sticky liquids, which
would either wear out, damage or block a mechanical
shaft seal.
The back-to-back double seal consists of two shaft
seals mounted back-to-back in a separate seal chamber,
see figure 1.3.17. The back-to-back double seal protects
the surrounding environment and the people working
with the pump.
The pressure in the seal chamber must be 1-2 bar higher
than the pump pressure. The pressure can be generated
by:
An existing, separate pressure source. Many

applications incorporate pressurised systems.
A separate pump, e.g. a dosing pump.
34
Cemented tungsten carbide covers the type of hard metals

that are based on a hard tungsten carbide (WC) phase and
usually a softer metallic binder phase. The correct technical
term is cemented tungsten carbide, however, the abbreviated
term tungsten carbide (WC) is used for convenience.
Cobalt-bonded (Co) WC is only corrosion resistant in water if
the pump incorporates base metal, such as cast iron.
Chromium-nickel-molybdenum-bounded WC has a
corrosion resistance equal to EN 14401.
Sintered binderless WC has the highest corrosion
resistance. However, its resistance to corrosion in liquids,
such as hypochlorite, is not as high. The material pairing
WC/WC has the following features:
Extremely wear resistant

Very robust, resists rough handling
Poor dry-running properties. In case of dry-running, the
temperature increases to several hundred degrees Celsius
in very few minutes and consequently damages the O-rings.
If a certain pressure and a certain temperature are
exceeded, the seal may generate noise. Noise is an
indication of poor seal operating conditions that in the
long term may cause wear of the seal. The limits of use
depend on seal face diameter and design.
To a WC/WC seal face pairing, the running-in wear period
where noise is to be expected may last 3-4 weeks, although
typically, no noise occurs during the first 3-4 days.
Silicon carbide/silicon carbide

(SiC/SiC)
Silicon carbide/silicon carbide (SiC/SiC) is an alternative to
WC/WC and is used where higher corrosion resistance is
required .
The SiC/SiC material pairing has the following features:
Very brittle material requiring careful handling
Consequently, in warm water, the Q 1P / Q 1P face material

pairing generates less noise than the WC/WC pairing.
However, noise from porous SiC seals must be expected
during the running-in wear period of 3-4 days.
Q 1G self-lubricating, sintered SiC
Several variants of SiC materials containing dry lubricants
are available on the market. The designation Q1G applies
to a SiC material, which is suitable for use in distilled or
demineralised water, as opposed to the above materials.
Extremely wear resistant

Extremely good corrosion resistance. SiC (Q , Q and
s
1
P
1
Q 1G ) hardly corrodes, irrespective of the pumped liquid

type. However, an exception is water with very poor
conductivity, such as demineralised water, which attacks
the SiC variants Q 1s and Q 1P, whereas Q 1G is corrosionresistant also in this liquid
In general, these material pairings have poor dry-running

properties however, the Q 1G / Q 1G material withstands a
limited period of dry-running on account of the
graphite content of the material
For different purposes, various SiC/SiC variants exist:
Q 1s, dense-sintered, fine-grained SiC
A direct-sintered, fine-grained SiC with a small amount of
tiny pores.
For a number of years, this SiC variant was used as a
standard mechanical shaft seal material. Pressure and
temperature limits are slightly below those of WC/WC.
P
1
Q , porous, sintered, fine-grained SiC

A variant of the dense-sintered SiC. This SiC variant has
large circular closed pores. The degree of porosity is 5-15%
and the size of the pores 10-50 m Ra.
The pressure and temperature limits exceed those of WC/WC.
Pressure and temperature limits of Q 1G / Q 1G are similar to

those of Q 1P / Q 1P.
The dry lubricants, i.e. graphite, reduce the friction in case
of dry-running, which is of decisive importance to the
durability of a seal during dry-running.
Carbon/tungsten carbide or carbon/

silicon carbide features
Seals with one carbon seal face have the following
features:
Brittle material requiring careful handling

Worn by liquids containing solid particles
Good corrosion resistance
Good dry-running properties (temporary dry-running)
The self-lubricating properties of carbon make the
seal suitable for use even with poor lubricating
conditions (high temperature) without generating
noise. However, such conditions will cause wear of
the carbon seal face leading to reduced seal life. The
wear depends on the pressure, temperature, liquid
diameter and seal design.
Low speeds reduce the lubrication between the seal
faces; as a result, increased wear might have been
expected. However, this is normally not the case because
the distance that the seal faces have to move is reduced.
35
Section 1.3
Metal-impregnated carbon (A) offers limited corro-
The centrifugal pumping action of the rotating parts.
sion resistance, but improved mechanical strength,

heat conductivity and thus reduced wear
The power consumption increases dramatically with

the speed of rotation (to the third power).
With reduced mechanical strength, but higher
The seal face friction.
corrosion resistance, synthetic resin-impregnated

carbon (B) covers a wide application field. Synthetic
resin-impregnated carbon is approved for drinking
water
The use of carbon/SiC for hot water applications may

cause heavy wear of the SiC, depending on the
quality of the carbon and water. This type of wear
primarily applies to Q1 S/carbon. The use of Q1 P,
Q 1G or a carbon/WC pairing causes far less wear. Thus,
carbon/WC, carbon/Q1P or carbon/Q1G are recommended
for hot water systems
Friction between the two seal faces consists of

friction in the thin liquid film and
friction due to points of contact between the
seal faces.
The level of power consumption depends on seal design,
lubricating conditions and seal face materials.
250
Power loss (W)

250
200
150
1.3.5 Factors affecting the seal

performance
Power loss (W)
200
150
100
100
50
50
3600
3600
0
0
0 2000
2000 4000 4000
6000 6000
8000
8000
10000
10000
12000
12000
Speed (rpm)
Speed (rpm)
As mentioned previously, no seal is completely tight. On

the next pages, we will present the following factors,
which have an impact on the seal performance: Energy
consumption, noise and leakage. These factors will be
presented individually. However, it is important to stress
that they are closely interrelated, and thus must be
considered as a whole.
Energy consumption
It comes as no surprise that power is needed to make the
seal rotate. The following factors contribute to the power
consumption, that is the power loss of a mechanical shaft
seal:
36
Fig. 1.3.18: Power consumption of a 12 mm

mechanical shaft seal
Pumping
Pumping
action
action
Friction
Friction
Figure 1.3.18 is a typical example of the power consumption

of a mechanical shaft seal. The figure shows that up to 3600
rpm friction is the major reason for the mechanical shaft
seals energy consumption.
Energy consumption is, especially in connection with

stuffing boxes, an important issue. As you can tell from
the example, replacing a stuffing box by a mechanical
shaft seal leads to considerable energy savings, see
figure 1.3.19.
Standard pump 50 mLC; 50 mm shaft and 2900 rpm
Noise
2.0 kWh
0.3 kWh
Leakage
Stuffing box
3.0 l/h (when mounted correctly)

0.8 ml/h
Fig. 1.3.19: Stuffing box versus mechanical shaft seal
Bar
The choice of seal face materials is decisive

for the
25
function and the life of the mechanical shaft seal. Noise
20
is generated as a result of the poor lubricating
conditions
Duty range
in seals handling low viscosity liquids. The viscosity
15
of water decreases with increasing temperature. This
10
means that the lubricating conditions decrease
as the
temperature rises. If the pumped liquid reaches or
5
exceeds boiling temperature, the liquid on part of the
seal face evaporates, which results in a further
decrease
0
10
20
30
in the lubricating conditions. A speed reduction has the
same effect, see figure 1.3.20.
Energy consumption
Stuffing box
Noise
Bar
25
Noise
20
Duty range
15
40
50
60
70
80
10
90
100
110
Speed at 3000 rpm

Speed at 1800 rpm
Speed at 1200 rpm
Speed at 600 rpm
Leakage
The pumped liquid lubricates the seal face of a
mechanical shaft seal. Thus, better lubrication means
less friction and increased leakage. Conversely, less
leakage means worse lubricating conditions and
increased friction. In practice, the amount of leakage
and power loss that occur in mechanical shaft seals can
vary. The reason is that leakage depends on factors which
are impossible to quantify theoretically because of type
of seal faces, type of liquid, spring load, etc. Therefore,
figure 1.3.21 should be perceived as a guideline.
10
20
30
40
50
60
70
80
90
100
110
Fig. 1.3.20: Relation between duty range and speed

Speed at 3000 rpm
Speed at 1800 rpm

Speed at 1200 rpm
1
10
100
Differential
pressure
be sealed
Speed
at to600
rpm p (bar)
00 800
1
Dw (mm) 100 B
B = balanced
U = unbalanced
100 U
15
80 B
n
00 00
30 1 ) 36
n
i
(m
80 U
60 B
60 U
40 B
40 U
30 B
30 U
20 B
To read the leakage rate curve correctly (figure 1.3.21),

you have to go through four steps:
20 U
Step 1: Read the pressure - in this case 5 bar

Step 2: 30 mm unbalanced shaft seal
Step 3: Speed 3000 rpm
0.001
0.01
0.06 0.1
Leakage Q (ml/h)
Fig. 1.3.21: Leakage rates
Step 4: Leakage rate 0.06 ml/h
37
Section 1.4: Motors

1.4.1
1.4.2
1.4.3
1.4.4
1.4.5
Standards
Motor start-up
Voltage supply
Frequency converter
Motor protection
Section 1.4
Motors
Motors are used in many applications all over the world.

The purpose of the electric motor is to create rotation, that is
to convert electric energy into mechanical energy. Pumps are
operated by means of mechanical energy, which is provided
by electric motors.
Fig. 1.4.1: Electric motor
1.4.1 Standards
Fig. 1.4.2: NEMA and IEC standards
40
NEMA
IEC
The National Electrical Manufacturers Association (NEMA)

sets standards for a wide range of electric products, including
motors. NEMA is primarily associated with motors used in
North America. The standards represent general industry
practices and are supported by the manufacturers of electric
equipment. The standards can be found in NEMA Standard
Publication No. MG1. Some large motors may not fall under
NEMA standards.
The International Electrotechnical Commission (IEC) sets

standards for motors used in many countries around the
world. The IEC 60034 standard contains recommended
electrical practices that have been developed by the
participating IEC countries.
ATEX (ATmosphre EXplosible) refers to two EU directives

about danger of explosion within different areas. The ATEX
directive concerns electrical, mechanical, hydraulic and
pneumatic equipment. As to the mechanical equipment,
the safety requirements in the ATEX directive ensure that
pump components, such as shaft seals and bearings do not
heat up and ignite gas and dust. The rst ATEX directive
(94/9/EC) deals with requirements put on equipment for
use in areas with danger of explosion. The manufacturer
has to full the requirements and mark his products with
categories. The second ATEX directive (99/92/EC) deals
with the minimum safety and health requirements that
the user has to full, when working in areas with danger of
explosion. Different techniques are used to prevent electric
equipment from becoming a source of ignition. In the
case of electric motors, protection types d (flameproof), e
(increased safety) and nA (non-sparking) are applied
in connection with gas, and DIP (dust ignition proof) is
applied in connection with dust.
Manufacturer
User
Directives and methods of protection

Ex-motors
Category 3
equipment
(3G/3D)
Zone:
2 or 22
Constant
danger
Potentiel
Fig 1.4.3: The link
danger
between zones and
equipment categories is Minor
a minimum requirement. danger
If the national rules are
more strict, they are the
ones to follow.
Zone:
1 or 21
Category 2
equipment
(2G/2D)
Zone:
0 or 20
Zone:
1 or 21
Category 1
equipment
(1G/1D)
Zone:
2 or 22
Zones:
Gas (G): 0, 1 and 2
Dust (D): 20, 21 and 22
Fig 1.4.4: The explosion occurs

inside the motor and is lead
out of the motor through the
flame paths. The temperature
classification for flameproof
EExd motors is valid for
external surfaces.
Flameproof motors - protection type EExd (de)

First of all, flameproof EExd (type de) motors are category
2G equipment for use in zone 1. The stator housing and
the flanges enclose the flameproof motor parts that
can ignite a potentially explosive atmosphere. Because
of the enclosure, the motor can withstand the pressure
that goes along with the explosion of an explosive
mixture inside the motor. Propagation of the explosion
to the atmosphere that surrounds the enclosure is hereby
avoided because the explosion is cooled down by means
of flame paths. The size of the flame paths is defined in
the EN 50018 standard. The surface temperature of the
flameproof enclosure should always be in accordance with
the temperature classes.
Fig 1.4.5: For increased safety

motors EExe, no sparks may
occur. The temperature
classification covers both
internal and external surfaces.
Increased safety motors - protection type EEx (e)

Increased safety motors (type e) are category 2G equipment
for use in zone 1. These motors are not flameproof and not
built to withstand an internal explosion. The construction
of such a motor is based on increased security against
Fig 1.4.6: With non-sparking

motors ExnA, no ignition is
likely to occur.
41
5
Section 1.4
Motors
possible excessive temperatures and occurrence of sparks

and arcs during normal operation and when a predictable
error occurs. The temperature classification for increased
safety motors is valid for both internal and external
surfaces, and therefore, it is important to observe the
stator winding temperature.
2D/category 2 equipment
Non-sparking motors (type nA) are category 3G equipment

for use in zone 2. These motors cannot by any means ignite
a potential explosive atmosphere under normal operation,
see figure 1.4.6.
In order to avoid static electricity to cause ignition, the

cooling fan on a category 2 DIP motor for use in zone 21
(area with potential danger of explosion) is made of metal.
Likewise, to minimise the risk of ignition, the external
ground terminal is subject to more severe demands of
construction. The external surface temperature of the
enclosure, which is indicated on the motor nameplate and
corresponds to the running performance during the worst
conditions allowed for the motor. Motors for use in zone 21
(areas with potential danger of explosion) have to be IP65
protected, that is completely protected against dust.
Dust Ignition Proof (DIP)
3D/category 3 equipment
Non-sparking motors - protection type Ex (nA)
Two types of Dust Ignition Proof motors exist: 2D/category

2 equipment and 3D/category 3 equipment.
Type of
protection
Standar ds
Code CENELEC
IEC
EN
60079
Use in A TEX
category/
Zone
The temperature indicated on a category 3 DIP motor for

use in zone 22 (areas with minor danger of explosion)
Principle
Application
General
requirements
50014
-0
Basic electrical requirements
All equipment
Oil immersion
50015
-6
Category 2
Zone 1
Electrical components immersed in oil

excluding explosive atmosphere from
igniting
Transformers
Pressurised
50016
-2
Category 2
Zone 1
Enclosure housing equipment is purged to

remove explosive atmosphere and pressurised to prevent ingress of
surrounding atmosphere
Switching and
control cabinets,
large motors
Powder filled
50017
-5
Category 2
Zone 1
Electrical parts are surrounded with

power, e.g. quartz to prevent contact with
an explosive atmosphere
Electronic devices,
e.g. capacitors, fuses
Flameproof
50018
-1
Category 2
Zone 1
Enclosure housing electrical equipment

which, if there is an internal explosion,
will not ignite surrounding atmosphere
AC motors,
control panels,
light fittings
Increased
safety
50019
-7
Category 2
Zone 1
Additional methods are used to

eliminate arcs, sparks and hot surface
capable of igniting flammable
atmosphere
AC motors, terminal
and connection boxes,
light fittings, squirrel
cage motors
ia
50020
- 11
Category 1
Zone 0
ib
50020
- 11
Category 2
Zone 1
Electrical energy in equipment is limited

so that circuits cannot ignite an
atmosphere by sparking or heating
Measurement and
control equipment,
e.g. sensors,
instrumentation
Encapsulation
50028
- 18
Category 2
Zone 1
Electrical components embedded in

approved material to prevent contact
with explosive atmosphere
Measurement and
control devices,
solenoid valves
Type of
protection n
nA
50021
- 15
Category 3
Zone 2
Non-arcing and non-sparking
AC motors, terminal
boxes, light fittings
Intrinsic safety
Note: Group II Dust atmospher es ar e covered by CENELEC EN 50281-1-1 and EN50281-1-2
Fig 1.4.7: Standards and methods of protection
42
corresponds to the running performance under the worst

conditions allowed for that specific motor. A motor for
use in zone 22 has to be IP55 protected, that is protected
against dust. The IP protection is the only difference
between 2D/category 2 equipment and 3D/category 3
equipment.
Mounting (International Mounting - IM)
Foot-mounted
motor
Flange-mounted
motor with
free-hole flange
IM B3
IM B5
IM B14
IM 1001
IM 3001
IM 3601
IM B35
IM V1
IM 3011
IM V18
IM 3611
IM 2001
Three different ways of mounting the motor exist: Footmounted motor, ange-mounted motor with free-hole
ange (FF) and ange-mounted motor with tapped-hole
ange (FT). Figure 1.4.8 shows the different ways of
mounting a motor and the standards that apply for the
mountings. The mounting of motors is stated according to
the following standards:
IEC 60034-7, Code I,

i.e. designation IM followed by the previously
used DIN 42590 code
IEC 60034-7, Code II
Enclosure class
(Ingress Protection - IP)
The enclosure class states the degrees of protection of
the motor against ingress of solid objects and water.
The enclosure class is stated by means of two letters IP
followed by two digits, for example IP55. The first digit
stands for protection against contact and ingress of solid
objects and the second digit stands for protection against
ingress of water, see figure 1.4.9.
Drain holes enable the escape of water which has entered
the stator housing for instance through condensation.
When the motor is installed in a damp environment, the
bottom drain hole should be opened. Opening the drain
hole changes the motors enclosure class from IP55 to
IP44.
Flange-mounted
motor with
tapped-hole flange
Fig 1.4.8: Different mounting methods
First digit
Second digit
Protection against contact and

ingress of solid objects
Protection against
ingress of water
0 No special protection
0 No special protection
1 The motor is protected against

solid objects bigger than
55 mm, e.g. a hand

vertically falling drops of water,
such as condensed water

objects bigger than 12 mm, e.g.
a finger

vertically falling drops of water,
even if the motor is tilted at an
angle of 15

solid objects bigger than 25 mm,
i.e. wires, tools, etc.
solid objects bigger than 1 mm,
e.g. wires
the ingress of dust
6 The motor is completely
dust-proof

water spray falling at an angle
of 60 from vertical
water splashing from any
direction
water being projected from a
nozzle from any direction
heavy seas or high-pressure
water jets from any direction
7 The motor is protected when
submerged from 15 cm to 1 m in
water for a period specified by
the manufacturer
continuous submersion in water
under conditions specified by
the manufacturer
Fig 1.4.9: The enclosure class is stated by means of two digits IP

followed by two letters; for example IP55
43
Section 1.4
Motors
Frame size
Flanges and shaft end comply with EN 50347 and

IEC 60072-1. Some pumps have a coupling, which requires
a smooth motor shaft end or a special shaft extension
which is not defined in the standards.
100mm
Figure 1.4.11 gives an overview of the relation between

frame size, shaft end, motor power and flange type and
size. For motors in frame sizes 63 up to and including 315M,
the relationship is specified in EN 50347. For motors with
frame size 315L and larger, no standard covers this relation.
The figure shows where on the motor the different values
that make up the frame size are measured.
B3
IEC 100L (In this case L = 140mm)
Distance between
holes
Fig 1.4.10: Frame size
Insulation class
The insulation class is defined in the IEC 60085 standard
and tells something about how robust the insulation
system is to temperatures. The life of an insulation
material is highly dependent on the temperature to which
it is exposed. The various insulation materials and systems
are classified into insulation classes depending on their
ability to resist high temperatures.
140mm
Hot-spot overtemperature
[C] 180
15
155
10
130
120
10
Maximum temperature increase
80
105
125
Maximum ambient temperature
40
40
40
40
Class
Maximum ambient
temperature
(C)
Maximum
temperature increase
(K)
Hot-spot
overtemperature
(K)
Maximum
winding temperature
(Tmax) (C)
40
80
10
130
40
105
10
155
40
125
15
180
Fig 1.4.12: Different insulation classes and their temperature increase at

nominal voltage and load
44
Fig 1.4.11: The relation between frame size and power input
1
Frame size
2
Shaft end diameter
3
Rated power
4
Flange size
2-pole
4-, 6-, 8-pole
2-pole
4-pole
6-pole
8-pole
Free-hole
flange
Tapped-hole
flange
[mm]
[mm]
[kW]
[kW]
[kW]
[kW]
(FF)
(FT)
56
0.09; 0.12
0.06;0.09
FF100
FT65
63
11
11
0.18; 0.25
0.12 ; 0.18
FF115
FT75
71
14
14
0.37; 0.55
0.25; 0.37
FF130
FT85
80
19
19
0.75; 1.1
0.55; 0.75
0.37; 0.55
90S
24
24
1.5
1.1
0.75
FF165
FT100
0.37
FF165
FT115
90L
24
24
2.2
1.5
1.1
0.55
FF165
FT115
100L
28
28
2.2; 3
1.5
0.75; 1.1
FF215
FT130
112M
28
28
2.2
1.5
FF215
FT130
132S
38
38
5.5; 7.5
5.5
2.2
FF265
FT165
132M
38
38
7.5
4; 5.5
FF265
FT165
160M
42
42
11; 15
11
7.5
4; 5.5
FF300
FT215
FT215
160L
42
42
18.5
15
11
7.5
FF300
180M
48
48
22
18.5
FF300
180L
48
48
22
15
11
FF300
200L
55
55
30; 37
30
18.5; 22
15
FF350
225S
55
60
37
30
18.5
FF400
225M
55
60
45
45
22
FF400
250M
60
65
55
55
37
30
FF500
280S
65
75
75
75
45
37
FF500
280M
65
75
90
90
55
45
FF500
315S
65
80
110
110
75
55
FF600
315M
65
80
132
132
90
75
FF600
315L
65
80
160; 200; 250
355
75
100
315; 355; 400; 450; 500
400
80
100
560; 630; 710
560; 630; 710
FF840
450
90
120
800; 900; 1000
800; 900; 1000
FF940
FF600
315; 355; 400; 450; 500
FF740
45
Section 1.4
Motors
1.4.2 Motor start-up

We distinguish between different ways of starting up
the motor: Direct-on-line starting, star/delta starting,
autotransformer starting, soft starter and frequency
converter starting. Each of these methods have their pros
and cons, see figure 1.4.13.
Fig 1.4.13: Starting method
Starting method
Pros
Cons
Simple and cost-efficient.

Safe starting.
High locked-rotor current.
Star/delta starting (SD)

(Y/)
Reduction of starting current by factor 3.
Current pulses when switching over from star to delta.

Not suitable if the load has a low inertia.
Reduced locked-rotor torque.
Reduction of locked-rotor current and torque.
Current pulses when switching from reduced to full voltage.

Soft starter
"Soft" starting. No current pulses.

Less water hammer when starting a pump.
Reduction of locked-rotor current as required,
typically 2-3 times.
Frequency converter starting
No current pulses.
Less water hammer when starting a pump.
Reduction of locked-rotor current as required,
typically 2 to 3 times.
Can be used for continuous feeding of the motor.

Expensive
As the name suggests, direct-on-line starting means that

the motor is started by connecting it directly to the supply
at rated voltage. Direct-on-line starting is suitable for stable
supplies and mechanically stiff and well-dimensioned
shaft systems, for example pumps. Whenever applying
the direct-on-line starting method, it is important to consult
local authorities.
As the name states, autotransformer starting makes use

of an autotransformer. The autotransformer is placed in
series with the motor during start and varies the voltage
up to nominal voltage in two to four steps.
Star/delta starting
A soft starter is, as you would expect, a device which

ensures a soft start of a motor. This is done by raising the
voltage to a preset voltage raise time.
The objective of this starting method, which is used with

three-phase induction motors, is to reduce the starting
current. In one position, current supply to the stator
windings is connected in star (Y) for starting. In other
positions, current supply is reconnected to the windings in
delta () once the motor has gained speed.
46
Soft starter
Frequency converter starting

Frequency converters are designed for continuous feeding
of motors, but they can also be used for soft starting.
1.4.3 Voltage supply

The motors rated voltage lies within a certain voltage
range. Figure 1.4.14 shows typical voltage examples for 50
Hz and 60 Hz motors.
According to the international standard IEC 60038, the
motor has to be able to operate with a main voltage
tolerance of 10%.
For motors that are designed according to the IEC 600341 standard with a wide voltage range, e.g. 380-415 V, the
main voltage may have a tolerance of 5%.
The permissible maximum temperature for the actual
insulation class is not exceeded when the motor is
operated within the rated voltage range. For conditions
at the extreme boundaries the temperature typically rises
approx. 10 Kelvin.
1.4.4 Frequency converter

Frequency converters are often used for speed controlling
pumps, see chapter 4. The frequency converter converts
the mains voltage into a new voltage and frequency,
causing the motor to run at a different speed. This way of
regulating the frequency might result in some problems:
Typical voltage examples

50 Hz
50 Hz motors come with the following voltages:
3 x 220 240 / 380 415 Y
3 x 200 220 / 346 380 Y
3 x 200 / 346 Y
3 x 380 415
1 x 220 230 / 240
60 Hz
60 Hz motors come with the following voltages:
3 x 200 230 / 346 400 Y
3 x 220 255 / 380 440 Y
3 x 220 277 / 380 480 Y
3 x 200 230 / 346 400 Y
3 x 380 480
Fig 1.4.14: Typical voltages
Mains voltage according to IEC 60038

50 Hz
+ 10%
230 V _
60 Hz
-
+ 10%
400 V _
+ 10%
690 V _
-
+ 10%
460 V _
Fig 1.4.15: Mains voltage according to IEC 60038
Acoustic noise from the motor, which is sometimes

transmitted to the system as disturbing noise
High voltage peaks on the output from the frequency

converter to the motor
47
Section 1.4
Motors
Insulation for motors with frequency

converter
Phase insulation also referred

to as phase paper
In connection with motors with frequency converters we

distinguish between different kinds of motors, with different
kinds of insulation.
Motors without phase insulation

For motors constructed without the use of phase
insulation, continuous voltages (RMS) above 460 V
can increase the risk of disruptive discharges in the
windings and thus destruction of the motor. This applies
to all motors constructed according to these principles.
Continuous operation with voltage peaks above 650 V can
cause damage to the motor.
Motors with phase insulation

In three-phase motors, phase insulation is normally
used and consequently, specific precautions are not
necessary if the voltage supply is smaller than 500 V.
Motors with reinforced insulation

In connection with supply voltages between 500 and
690 V, the motor has to have reinforced insulation or be
protected with delta U /delta t filters. For supply voltages
of 690 V and higher the motor has to be fitted with both
reinforced insulation and delta U /delta t filters.
Motors with insulated bearings

In order to avoid harmful current flows through the
bearings, the motor bearings have to be electrically insulated.
This applies for motors from frame size 280 and up.
48
Fig 1.4.16: Stator with phase insulation
Motor efficiency
Generally speaking, electric motors are quite efficient.
Some motors have electricity-to-shaft power efficiencies
of 80-93% depending on the motor size and sometimes
even higher for bigger motors. Two types of energy losses
in electric motors exist: Load dependent losses and load
independent losses.
Load dependent losses vary with the square of the current
and cover:
Stator winding losses (copper losses)

Rotor losses (slip losses)
Stray losses (in different parts of the motor)
Motors can fail because of overload for a longer period of

time and therefore most motors are intentionally oversized
and only operate at 75% to 80% of their full load capacity.
At this level of loading, motor efficiency and power factor
remain relatively high. But when the motor load is less
than 25%, the efficiency and the power factor decrease.
The motor efficiency drops quickly below a certain
percentage of the rated load. Therefore, it is important to
size the motor so that the losses associated with running
the motor too far below its rated capacity are minimised.
It is common to choose a pump motor that meets the
power requirements of the pump.
1.4.5 Motor protection
Load independent losses in the motor refer to:
Iron losses (core losses)

Mechanical losses (friction)
100
0.8
80
0.6
60
0.4
Percent
The type of thermal protection varies with the motor type.

The construction of the motor together with the power
consumption must be taken into consideration when choosing
thermal protection. Generally speaking, motors have to be
protected against the following conditions:
40
0.2
20
Fig 1.4.17: Efficiency vs. load

power factor vs. load
(schematic drawing)
Efficiency
Power factor
0
25
50
75
100
125
Percent of rated load
100
150
75 kW
90
7.5 kW
80
0.75 kW
70
60
Efficiency %
Cos
Different motor classifications categorise motors according

to efficiency. The most important are CEMEP in the EU (EFF1,
EFF2 and EFF3) and EPAct in the US.
Motors are nearly always protected against reaching temperatures,

which can damage the insulation system. Depending on
the construction of the motor and the application, thermal
protection can also have other functions, e.g. prevent damaging
temperatures in the frequency converter if it is mounted on
the motor.
Errors causing slow temperature increases in

the windings:
Slow overload
Long start-up periods
Reduced cooling / lack of cooling
Increased ambient temperature
Frequent starts and stops
Frequency fluctuation
Voltage fluctuation
50
Fig 1.4.18: The relation

between efficiency and
rated load of different
sized motors (schematic
drawing)
40
30
20
10
0
25
50
100 125
75
Percent of rated load
150
Errors causing fast temperature increases in

the windings:
Blocked rotor
Phase failure
175
49
Thermal protection (TP)
Thermal switch and thermostats
According to the IEC 60034-11 standard, the thermal

protection of the motor has to be indicated on the
nameplate with a TP designation. Figure 1.4.19 shows an
overview of the TP designations.
Symbol
TP 111
TP 112
TP 121
TP 122
TP 211
TP 212
TP 221
TP 222
TP 311
TP 312
Technical overload with

variation (1 digit)
Only slow
(i.e. constant
overload)
Slow and fast
(i.e. constant overload
and blocked condition )
Only fast
(i.e. blocked condition)
Number af levels and

function area (2 digits)
Category 1
(3 digits)
1 level at cutoff
1
2
1
2
2 levels at emergency
signal and cutoff
1 level at cutoff
2 levels at emergency
signal and cutoff
1 level at cutoff
1
2
1
2
1
2
Indication of the permissible temperature level when the motor is exposed to thermal
overload. Category 2 allows higher temperatures than category 1 does.
Fig 1.4.19: TP designations
PTC thermistors
PTC thermistors (Positive Temperature Coefficient
Thermistors) can be tted into the windings of a motor
during production or retrotted afterwards. Usually 3
PTCs are tted in series; 1 in each phase of the winding.
They can be purchased with trip temperatures ranging
from 90C to 180C in 5 degrees steps. PTCs have to be
connected to a thermistor relay, which detects the rapid
increase in resistance of the thermistor when it reaches its
trip temperature. These devices are non-linear. At ambient
temperatures the resistance of a set of 3 will be about 200300 ohms and this will increase rapidly when the thermistor
reaches its trip temperature. If the temperature increases
any further, the PTC thermistor can reach several thousand
ohms. The thermistor relays are usually set to trip at 3000
ohms or are preset to trip according to what the DIN 44082
standard prescribes. The TP designation for PTCs for motors
smaller than 11kW is TP211 if the PTCs are tted into the
windings. If the PTCs are retrotted the TP designation is
TP111. The TP designation for PTCs for motors larger than
11kW is normally TP111.
50
Thermal switches are small bi-metallic switches that switch

due to the temperature. They are available with a wide range
of trip temperatures; normally open and closed types. The
most common type is the closed one. One or two, in series,
are usually tted in the windings like thermistors and can be
connected directly to the circuit of the main contactor coil.
In that way no relay is necessary. This type of protection is
cheaper than thermistors, but on the other hand, it is less
sensitive and is not able to detect a locked rotor failure.
Thermal switches are also referred to as Thermik, Klixon
switches and PTO (Protection Thermique Ouverture).
Thermal switches always carry a TP111 designation.
Single-phase motors
Single-phase motors normally come with incorporated
thermal protection. Thermal protection usually has an
automatic reclosing. This implies that the motor has to
be connected to the mains in a way that ensures that
accidents caused by the automatic reclosing are avoided.
Three-phase motors
Three-phase motors have to be protected according to local
regulations. This kind of motor has usually incorporated
contacts for resetting in the external control circuit.
Standstill heating
A heating element ensures the standstill heating of
the motor. The heating element is especially used in
connection with applications that struggle with humidity
and condensation. By using the standstill heating, the
motor is warmer than the surroundings and thereby the
relative air humidity inside the motor is always lower than
100%.
The fixed bearing in the drive end can be either a deepgroove ball bearing or an angular contact bearing.
Bearing clearances and tolerances are stated according
to ISO 15 and ISO 492. Because bearing manufacturers
have to fulfil these standards, bearings are internationally
interchangeable.
In order to rotate freely, a ball bearing must have a certain
internal clearance between the raceway and the balls.
Without this internal clearance, the bearings can either
be difficult to rotate or it may even seize up and be unable
to rotate. On the other hand, too much internal clearance
will result in an unstable bearing that may generate
excessive noise or allow the shaft to wobble.
Depending on which pump type the motor is fitted, the
deep-groove ball bearing in the drive end must have C3
or C4 clearance. Bearings with C4 clearance are less heat
sensitive and have increased axial load-carrying capacity.
1.4.20: Stator with heating element
Maintenance
The motor should be checked at regular intervals. It is
important to keep the motor clean in order to ensure
adequate ventilation. If the pump is installed in a dusty
environment, the pump must be cleaned and checked
regularly.
The bearing carrying the axial forces of the pump can have
C3 clearance if:
the pump has complete or partial hydraulic relief

the pump has many brief periods of operation
the pump has long idle periods
C4 bearings are used for pumps with fluctuating high axial
forces. Angular contact bearings are used if the pump exerts
strong one-way axial forces.
Drive end
Non-drive end
Bearings
Normally, motors have a locked bearing in the drive end and
a bearing with axial play in the non-drive end. Axial play is
required due to production tolerances, thermal expansion
during operation, etc. The motor bearings are held in place
by wave spring washers in the non-drive end, see figure
1.4.21.
Spring washer
Non-drive end bearing
Drive end bearing
Fig 1.4.21: Cross-sectional drawing of motor
51
Section 1.4
Motors
Axial forces
Bearing types and recommended clearance

Drive-end
Non-drive-end
Moderate to strong forces.

Primarily outward pull on
the shaft end
Fixed deep-groove ball bearing (C4)
Deep-groove ball bearing (C3)
Strong outward pull

on the shaft end
Fixed angular contact bearing
Small forces
(flexible coupling)
Strong inward
pressure
Fixed angular contact bearing
Moderate forces.
Primarily outward pull on
the shaft end (partly
hydraulically relieved in
the pump)
Fig:1.4.22: Typical types of bearings in pump motors
Motors with permanently lubricated bearings

For closed permanently lubricated bearings, use one of the
following high temperature resistant types of grease:
Lithium-based grease
Polyurea-based grease
The technical specifications must correspond to the
standard DIN - 51825 K2 or better. The basic oil viscosity
must be higher than:
50 cSt (10-6m2/sec) at 40C and

8 cSt (mm2/sec) at 100C
For example Klberquiet BQH 72-102 with a grease
filling ratio of: 30 - 40%.
Motors with lubrication system

Normally, frame size 160 motors and upwards have
lubricating nipples for the bearings both in the drive end
and the non-drive end.
52
The lubricating nipples are visible and easily accessible.

The motor is designed in such a way that:
there is a flow of grease around the bearing

new grease enters the bearing
old grease is removed from the bearing
Motors with lubricating systems are supplied with a
lubricating instruction, for instance as a label on the
fan cover. Apart from that, instructions are given in the
installation and operating instructions.
The lubricant is often lithium-based, high temperature
grease, for instance EXXON UNIREX N3 or Shell Alvania
Grease G3. The basic oil viscosity must be
higher than 50 cSt (10-6m2/sec) at 40C and
8 cSt (mm2/sec) at 100C
Section 1.5: Liquids

1.5.1 Viscous liquids
1.5.2 Non-Newtonian liquids
performance of a centrifugal pump
1.5.4 Selecting the right pump for a liquid
with antifreeze
1.5.5 Calculation example
1.5.6 Computer aided pump selection for
dense and viscous liquids
Section 1.5
Liquids
1.5.1 Viscous liquids

There is no doubt about it; water is the most common
liquid that pumps handle. However, in a number of
applications, pumps have to handle other types of liquids,
e.g. oil, propylene glycol, gasoline. Compared to water,
these types of liquids have different density and viscosity.
Viscosity is a measure of the thickness of the liquid.
The higher the viscosity, the thicker the liquid. Propylene
glycol and motor oil are examples of thick or high viscous
liquids. Gasoline and water are examples of thin, low
viscous liquids.
Two kinds of viscosity exist:
The dynamic viscosity (), which is normally measured
in Pas or Poise. (1 Poise = 0.1 Pas)
The kinematic viscosity (), which is normally measured

in centiStokes or m2/s (1 cSt = 10-6 m2/s)
= density of liquid
The relation between the dynamic viscosity () and the

kinematic viscosity () is shown in the formula on your
right hand side.
On the following pages, we will only focus on kinematic
viscosity ().
The viscosity of a liquid changes considerably with the
change in temperature; hot oil is thinner than cold oil. As
you can tell from figure 1.5.1, a 50% propylene glycol liquid
increases its viscosity 10 times when the temperature
changes from +20 to 20 oC.
For more information concerning liquid viscosity, go to
appendix L.
54
Liquid
Liquid
Density
temperature [kg/m3]
t [C]
Kinematic
viscosity
[cSt]
998
1.004
20
733
0.75
20
900
93
Water
20
Gasoline
Olive oil
50% Propylene glycol
20
1043
6.4
50% Propylene glycol
-20
1061
68.7
Fig. 1.5.1: Comparison of viscosity values for water and a few other liquids.
Density values and temperatures are also shown
1.5.2 Non-Newtonian liquids

The liquids discussed so far are referred to as Newtonian
fluids. The viscosity of Newtonian liquids is not affected by
the magnitude and the motion that they are exposed to.
Mineral oil and water are typical examples of this type of
liquid. On the other hand, the viscosity of non-Newtonian
liquids does change when agitated.
This calls for a few examples:
Dilatant liquids like cream the viscosity increases
when agitated
Plastic fluids like catsup have a yield value, which has
to be exceeded before flow starts. From that point on,
the viscosity decreases with an increase in agitation
Thixotrophic liquids like non-drip paint - exhibit a
decreasing viscosity with an increase in agitation
Lower freezing point, tf [C]

Lower specific heat, cp [kJ/kg.K]
Lower thermal conductivity, [W/m.K]
Higher boiling point, tb [C]
Higher coefficient of expansion, [m/C]
Higher density, [kg/m3]
Higher kinematic viscosity, [cSt]
These properties have to be kept in mind when designing

a system and selecting pumps. As mentioned earlier,
the higher density requires increased motor power and
the higher viscosity reduces pump head, flow rate and
efficiency resulting in a need for increased motor power,
see figure 1.5.2.
H, P,
The non-Newtonian liquids are not covered by the viscosity

formula described earlier in this section.

performance of a centrifugal pump
Viscous liquids, that is liquids with higher viscosity and/

or higher density than water, affect the performance of
centrifugal pumps in different ways:
Power consumption increases, i.e. a larger motor may
be required to perform the same task
Q
Fig. 1.5.2: Changed head, efficiency and power input for
liquid with higher viscosity
Head, flow rate and pump efficiency are reduced

Let us have a look at an example. A pump is used for
pumping a liquid in a cooling system with a liquid
temperature below 0oC. To avoid that the liquid freezes,
an antifreeze agent like propylene glycol is added to
the water. When glycol or a similar antifreeze agent is
added to the pumped liquid, the liquid obtains properties,
different from those of water. The liquid will have:
55
Section 1.5
Liquids
1.5.4 Selecting the right pump for a

liquid with antifreeze
KH
1.35
1.30
cSt
100
1.25
40
1.15
cSt
1.20
60
Pump characteristics are usually based on water at around

20C, i.e. a kinematic viscosity of approximately 1 cSt and
a density of approximately 1,000 kg/m.
When pumps are used for liquids containing antifreeze
below 0C, it is necessary to examine whether the pump
can supply the required performance or whether a
larger motor is required. The following section presents
a simplified method used to determine pump curve
corrections for pumps in systems that have to handle a
viscosity between 5 - 100 cSt and a density of maximum
1,300 kg/m. Please notice that this method is not as
precise as the computer aided method described later in
this section.
cS
1.10
1.05
20
cS
t
10
cSt
5 cS
t
1.00
KP2
Pump curve corrections for pumps handling high

viscous liquid
Based on knowledge about required duty point, QS, HS, and
kinematic viscosity of the pumped liquid, the correction
factors of H and P2 can be found, see figure 1.5.3.
1.9
1.8
1.7
10
1.6
1.5
cS
60
c
St
1.4
40
cSt
20 c
St
10 c
St
1.3
1.2
1.1
5 cSt
1.0
0.9
Q [m3/h]
140
130
0m
100
=2
H=
10
120
110
90
80
=4
H=
70
m
m
60
60
50
40
30
20
10
=6
Fig. 1.5.3: It is possible to determine the correction factor for head and
power consumption at different flow, head and viscosity values
56
Figure 1.5.3 is read in the following way:

H
When kH and kP2 are found in the figure, the equivalent

head for clean water HW and the corrected actual shaft
power P2S can be calculated by the following formula
Hw = kH . HS
HW = kH . HS
Hw
Hs
s
w
( )
P2S = kP2 . P2w .
HS : is the desired head of the pumped liquid

(with agents)
1
Mixture
Qs
where
HW : is the equivalent head of the pump if the pumped
liquid is clean water
P2W : is the shaft power at the duty point (QS,HW) when
the pumped liquid is water
Water
Q
3
P
P2s
P2S = KP2 . P2w .
( ws )
P2w
5
4
Mixture
Water
P2S : is the shaft power at the duty point (Qs,Hs) when

the pumped liquid is water (with agents)
s : is the density of the pumped liquid
Q
Fig. 1.5.4: Pump curve correction when choosing the right pump for
the system
w : is the density of water = 998 kg/m3
The pump and motor selecting procedure contains the

following steps:
The pump selection is based on the normal data sheets/

curves applying to water. The pump should cover the duty
point Q,H = QS,HW, and the motor should be powerful
enough to handle P2S on the shaft.
Calculate the corrected head Hw

(based on HS and kH), see figure 1.5.4 1-2
Figure 1.5.4 shows how to proceed when selecting a pump

and testing whether the motor is within the power range
allowed.
Choose a pump capable of providing performance

according to the corrected duty point (QS, HW)
Read the power input P2W in the duty point (QS,Hw),
see figure 1.5.4 3-4
Based on P2W , kP2 , W , and S calculate the
corrected required shaft power P2S , see figure 1.5.4 4-5
Check if P2S < P2 MAX of the motor. If that is the case
the motor can be used. Otherwise select a more
powerful motor
57
Section 1.5
Liquids
1.5.5 Calculation example

A circulator pump in a refrigeration system is to pump a
40% (weight) propylene glycol liquid at 10C. The desired
flow is QS = 60 m3/h, and the desired head is HS = 12 m.
Knowing the required duty point, it is possible to find the QHcharacteristic for water and choose a pump, which is able to
cover the duty point. Once we have determined the needed
pump type and size we can check if the pump is fitted with a
motor, which can handle the specific pump load.
The liquid has kinematic viscosity of 20 cSt and a density
of 1049 kg/m3. With QS = 60 m3/h, HS = 12 m and = 20 cSt,
the correction factors can be found in figure 1.5.3.
1.5.6 Computer aided pump selection for

dense and viscous liquids
Some computer aided pump selection tools include a
feature that compensates for the pump performance
curves based on input of the liquid density and viscosity.
Figure 1.5.5 shows the pump performance curves from the
example we just went through.
The figure shows both the performance curves for the
pump when it handles viscous liquid (the full lines) and
the performance curves when it handles water (the broken
lines). As indicated head, flow and efficiency are reduced,
resulting in an increase in power consumption.
The value of P2 is 3.4 kW, which corresponds to the result
we got in the calculation example in section 1.5.4.
kH = 1.03
kP2 = 1.15
HW = kH HS = 1.03 12 = 12.4 m
QS = 60 m3/h
H
[m]
[%]
14
12
10
The pump has to be able to cover a duty point equivalent

to Q,H = 60 m3/h, 12.4m. Once the necessary pump size is
determined, the P2 value for the duty point is found, which
in this case is P2W = 2.9 kW. Now it is possible to calculate
the required motor power for propylene glycol mixture:
8
70
6
4
2
0
0
P2
[kW]
P2S = kP2 . P2w .
S
w
10
20
30
40
50
60
70
80 Q [m3/h]
4
3
2
1
0
1049
P2S = 1.15 . 2.9 .
998
Q [m3/h]
= 3.5 kW
The calculation shows, that the pump has to be fitted with

a 4 kW motor, which is the smallest motor size able to
cover the calculated P2S = 3.5 kW.
58
Fig. 1.5.5: Pump performance curves
60
50
40
30
20
10
0
Section 1.6: Materials

1.6.1
1.6.2
1.6.3
1.6.4
1.6.5
1.6.6
1.6.7
What is corrosion?
Types of corrosion
Metal and metal alloys
Ceramics
Plastics
Rubber
Coatings
Section 1.6
Materials
In this section you can read about different materials that

are used for pump construction. Our main focus will be
on the features that every single metal and metal alloy
have to offer. But before we dig any further into the
world of materials, we will have a closer look at corrosion.
Besides explaining what corrosion is, we will examine the
different types of corrosion and what can be done to
prevent corrosion from occurring.
1.6.1 What is corrosion?

Corrosion is usually referred to as the degradation of the
metal by chemical or electrochemical reaction with its
environment, see figure 1.6.1. When considered broadly,
corrosion may be looked upon as the tendency of the
metal to revert to its natural state similar to the oxide
from which it was originally melted. Only precious metals,
such as gold and platinum are found in nature in their
metallic state.
Environmental variables that affect the

corrosion resistance of metals and alloys
pH (acidity)
Oxidizing agents (such as oxygen)
Temperature
Concentration of solution constituents
(such as chlorides)
Biological activity
Some metals produce a tight protective oxide layer on the

surface, which hinders further corrosion. If the surface
layer is broken it is self-healing. These metals are passivated.
Under atmospheric conditions the corrosion products
of zinc and aluminium form a fairly tight layer and
further corrosion is prevented.
Likewise, on the surface of stainless steel a tight layer of
iron and chromium oxide is formed and on the surface of
titanium a layer of titanium oxide is formed. The protective
layer of these metals explains their good corrosion
resistance. Rust, on the other hand, is a non-protective
corrosion product on steel.
Rust is porous, not firmly adherent and does not prevent
continued corrosion, see figure 1.6.2.
Operating conditions
(such as velocity, cleaning procedures and shutdowns)
Fig. 1.6.1: Environmental variables that affect the corrosion
resistance of metals and alloys
Rust on steel
Non-protective corrosion product

Oxide layer on stainless steel
Protective corrosion product

Fig. 1.6.2: Examples of corrosion products
60
1.6.2 Types of corrosion

Generally, metallic corrosion involves the loss of metal at
a spot on an exposed surface. Corrosion occurs in various
forms ranging from uniform attacks over the entire surface
to severe local attacks.
The environments chemical and physical conditions
determine both the type and the rate of corrosion attacks. The
conditions also determine the type of corrosion products that
are formed and the control measures that need to be taken. In
many cases, it is impossible or rather expensive to completely
stop the corrosion process; however, it is usually possible to
control the process to acceptable levels.
On the following pages we will go through the different
forms of corrosion in order to give you an idea of their
characteristics.
Uniform corrosion
Uniform or general corrosion is characterised by corrosive
attacks proceeding evenly over the entire surface, or on a
large part of the total area. General thinning continues until
the metal is broken down. Uniform corrosion is the type of
corrosion where the largest amount of metal is wasted.
Examples of metals, which are subject to uniform
corrosion:
Steel in aerated water
Stainless steel in reducing acids (such as EN 1.4301
(AISI 304) in sulfuric acid)
Fig. 1.6.3: Uniform corrosion
Pitting corrosion
Pitting corrosion is a localised form of corrosive attacks.
Pitting corrosion forms holes or pits on the metal surface.
It perforates the metal while the total corrosion, measured
by weight loss, might be rather minimal. The rate of
penetration may be 10 to 100 times that of general
corrosion depending on the aggressiveness of the liquid.
Pitting occurs more easily in a stagnant environment.
Fig. 1.6.4: Pitting corrosion
Example of metal that is subject to pitting corrosion:

Stainless steel in seawater
61
1. Design
Section
1.6
of pumps and motors
Materials
1.1 Pump construction, (10)
Crevice corrosion
Crevice corrosion - like pitting corrosion - is a localised
form of corrosion attack. However, crevice corrosion starts
more easily than pitting. Crevice corrosion occurs at narrow
openings or spaces between two metal surfaces or between
metals and non-metal surfaces and is usually associated
with a stagnate condition in the crevice. Crevices, such as
those found at flange joints or at threaded connections,
are thus often the most critical spots for corrosion.
Example of metal that is subject to crevice corrosion:
Stainless steel in seawater
Fig. 1.6.5: Crevice corrosion
As the name implies, intergranular corrosion occurs at
grain boundaries. Intergranular corrosion is also called
intercrystalline corrosion. Typically, this type of corrosion
occurs when chromium carbide precipitates at the grain
boundaries during the welding process or in connection
with insufficient heat treatment. A narrow region around
the grain boundary may therefore deplete in chromium
and become less corrosion resistant than the rest of the
material. This is unfortunate because chromium plays an
important role in corrosion resistance.
Examples of metals that are subject to intergranular corrosion:
Stainless steel - which is insufficiently welded or
heat-treated
Stainless steel EN 1.4401 (AISI 316) in concentrated
nitric acid
Fig. 1.6.6: Intergranular corrosion
Selective corrosion
Selective corrosion is a type of corrosion which attacks
one single element of an alloy and dissolves the element
in the alloy structure. Consequently, the alloys structure
is weakened.
Examples of selective corrosion:
The dezincification of unstabilised brass, whereby a
weakened, porous copper structure is produced
Graphitisation of gray cast iron, whereby a brittle
graphite skeleton is left because of the dissolution
of iron
62
Brass
Zinc corrosion products
Copper
Fig. 1.6.7: Selective corrosion
Erosion corrosion
Erosion corrosion is a process that involves corrosion
and erosion. The rate of corrosion attack is accelerated
by the relative motion of a corrosive liquid and a
metal surface. The attack is localised in areas with
high velocity or turbulent flow. Erosion corrosion
attacks are characterised by grooves with directional
pattern.
Examples of metals which are subject to erosion corrosion:
Bronze in seawater
Copper in water
Flow
Fig. 1.6.8: Erosion corrosion
A pumped liquid with high velocity reduces the pressure.
When the pressure drops below the liquid vapour
pressure, vapour bubbles form (the liquid boils).
In the areas where the vapour bubbles form, the
liquid is boiling. When the pressure raises again, the
vapour bubbles collapse and produce intensive
shockwaves. Consequently, the collapse of the vapour
bubbles remove metal or oxide from the surface.
Examples of metals that are subject to cavitation:
Cast iron in water at high temperature
Bronze in seawater
Fig. 1.6.9: Cavitation corrosion

Stress corrosion cracking (SCC) refers to the combined
influence of tensile stress (applied or internal) and
corrosive environment. The material can crack without
any significant deformation or obvious deterioration of
the material. Often, pitting corrosion is associated with
the stress corrosion cracking phenomena.
Examples of metals that are subject to stress corrosion
cracking:
Stainless steel EN 1.4401 (AISI 316) in chlorides
Brass in ammonia
Fig. 1.6.10: Stress corrosion cracking
63
1.
Design
Section
1.6 of pumps and motors
<
Materials
Corrosion fatigue
Pure mechanical fatigue is when a material subjected
to a cyclic load far below the ultimate tensile strength
can fail. If the metal is simultaneously exposed to a
corrosive environment, the failure can take place at an
even lower stress and after a shorter time. Contrary to
a pure mechanical fatigue, there is no fatigue limit in
corrosion-assisted fatigue.
Fig. 1.6.11: Corrosion fatigue
Example of metals that are subject to corrosion fatigue:

Aluminium structures in corrosive atmosphere
Galvanic corrosion
When a corrosive electrolyte and two metallic materials
are in contact (galvanic cell), corrosion increases on the
least noble material (the anode) and decreases on the
noblest (the cathode). The increase in corrosion is called
galvanic corrosion. The tendency of a metal or an alloy
to corrode in a galvanic cell is determined by its position
in the galvanic series. The galvanic series indicates the
relative nobility of different metals and alloys in a given
environment (e.g. seawater, see figure 1.6.12).
The farther apart the metals are in the galvanic series,
the greater the galvanic corrosion effect will be. Metals or
alloys at the upper end are noble, while those at the lower
end are least noble.
Aluminium - less noble
Copper - most noble
Fig. 1.6.12: Galvanic corrosion
Examples of metal that are subject to galvanic corrosion:

Steel in contact with 1.4401
Aluminium in contact with copper
The principles of galvanic corrosion are used in cathodic
protection. Cathodic protection is a means of reducing
or preventing the corrosion of a metal surface by the
use of sacrificial anodes (zinc or aluminum) or impressed
currents.
Fig. 1.6.13: Galvanic series for metals and alloys in seawater
64
1.6.3 Metal and metal alloys

On the following pages, you can read about the features
of different metals and metal alloys, used for construction
of pumps.
Cavitation corrosion of bronze impeller
Ferrous alloys
Ferrous alloys are alloys where iron is the prime constituent.
Ferrous alloys are the most common of all materials
because of their availability, low cost, and versatility.
Steel
Erosion corrosion of cast iron impeller
Steel is a widely used material primarily composed of iron

alloyed with carbon. The amount of carbon in steel varies
in the range from 0.003% to 1.5% by weight. The content of
carbon has an important impact on the materials strength,
weldability, machinability, ductility, and hardness. As a
rule-of-thumb, an increase in carbon content will lead to
an increase in strength and hardness but to a decrease in
ductility and weldability. The most common type of steel is
carbon steel. Carbon steel is grouped into four categories,
see figure 1.6.14.
Pitting corrosion of EN 1.4401 (AISI 316)
1 mm
Type of steel
Content of carbon
Low carbon or mild steel
0.003% to 0.30% of carbon
Medium carbon steel
High carbon steel
Very high carbon steel
Fig 1.6.14: Four types of carbon steel
Intergranular corrosion of
stainless steel
Crevice corrosion of
EN 1.4462 (SAF 2205)
Steel is available in wrought as well as in cast condition.

The general characteristics of steel castings are closely
comparable to those of wrought steels. The most obvious
advantage of steel is that it is relatively inexpensive to make,
form and process. On the other hand, the disadvantage
of steel is that its corrosion resistance is low compared to
alternative materials, such as stainless steel.
65
1.
Design
Section
Materials
Cast iron
Cast iron can be considered an alloy of iron, silicon
and carbon. Typically, the concentration of carbon is
between 3-4% by weight, most of which is present
in insoluble form (e.g. graphite flakes or nodules).
The two main types are grey cast iron and nodular
(ductile) cast iron. The corrosion resistance of cast iron is
comparable to the one for steel; and sometimes even better.
Cast iron can be alloyed with 13-16% by weight silicon or
15-35% by weight nickel (Ni-resist) respectively in order to
improve corrosion resistance. Various types of cast irons are
widely used in industry, especially for valves, pumps, pipes
and automotive parts. Cast iron has good corrosion resistance
to neutral and alkaline liquids (high pH) . But its resistance to
acids (low pH) is poor.
Grey iron
Fig 1.6.15: Comparison and designations of grey iron
In grey iron, the graphite is dispersed throughout a ferrite

or pearlite matrix in the form of flakes. Fracture surfaces
take on a grey appearance (hence the name!). The graphite
flakes act as stress concentrators under tensile loads,
making it weak and brittle in tension, but strong
and ductile in compression. Grey iron is used for the
construction of motor blocks because of its high vibration
damping ability. Grey iron is an inexpensive material and
is relatively easy to cast with a minimal risk of shrinkage.
That is why grey iron is often used for pump parts with
moderate strength requirements.
66
Nodular (ductile) iron
Fig 1.6.16: Comparison and designations of nodular iron
Nodular iron contains around 0.03-0.05% by weight of

magnesium. Magnesium causes the flakes to become
globular so the graphite is dispersed throughout a ferrite
or pearlite matrix in the form of spheres or nodules. The
graphite nodules have no sharp features. The round shape
of nodular graphite reduces the stress concentration and
consequently, the material is much more ductile than grey
iron. Figure 1.6.16 clearly shows that the tensile strength is
higher for nodular iron than is the case for grey iron. Nodular
iron is normally used for pump parts with high strength
requirements (high pressure or high temperature
applications).
Stainless steel
Stainless steel is chromium containing steel alloys. The
minimum chromium content in standardised stainless
steel is 10.5%. Chromium improves the corrosion resistance
of stainless steel. The higher corrosion resistance is due
to a chromium oxide film that is formed on the metal
surface. This extremely thin layer is self-repairing under
the right conditions.
Molybdenum, nickel and nitrogen are other examples of
typical alloying elements. Alloying with these elements
brings out different crystal structures, which enable
different properties in connection with machining, forming,
welding, corrosion resistance, etc. In general, stainless
steel has a higher resistance to chemicals (i.e. acids) than
steel and cast iron have.
In environments containing chlorides, stainless steel can

be attacked by localised corrosion, e.g. pitting corrosion
and crevice corrosion. The resistance of stainless steel to
these types of corrosion is highly dependent on its
chemical composition. It has become rather common to
use the so-called PRE (Pitting Resistance Equivalent)
values as a measure of pitting resistance for stainless
steel. PRE values are calculated by formulas in which the
relative influence of a few alloying elements (chromium,
molybdenum and nitrogen) on the pitting resistance is

taken into consideration. The higher the PRE, the higher
the resistance to localised corrosion. Be aware that the PRE
value is a very rough estimate of the pitting resistance of
a stainless steel and should only be used for comparison/
classification of different types of stainless steel.
In the following, we will present the four major types of
stainless steel: ferritic, martensitic, austenitic and duplex.
Fig 1.6.17: Chemical composition of stainless steel
Chemical composition of stainless steel [w%]

Microstructure
1)
5)
Designation
EN/AISI/UNS
%
Carbon max.
%
Chromium
%
Nickel
%
Molybdenum
%
Other
PRE 5)
Ferritic
1.4016/430/ S43000
0.08
16-18
Martensitic
1.4057/431/ S43100
0.12-0.22
15-17
1.5-2.5
Austenitic
1.4305/303/ S30300
0.1
17-19
8-10
Austenitic
1.4301/304/ S30400
0.07
17-19.5
8-10.5
18
Austenitic
1.4306/304L/ S30403
0.03
18-20
10-12
18
Austenitic
1.4401/316/ S31600
0.07
16.5-18.5
10-13
2-2.5
24
Austenitic
1.4404/316L/ S31603
0.03
16.5-18.5
10-13
2-2.5
24
Austenitic
1.4571/316Ti/
S31635
0.08
16.5-18.5
10.5-13.5
2-2.5
Ti > 5 x carbon
Ti < 0.70
24
Austenitic
1.4539/904L/ N08904
0.02
19-21
24-26
4-5
Cu 1.2-2
34
Austenitic
1.4547/none /
S 31254 3)
0.02
20
18
6.1
N 0.18-0.22
Cu 0.5-1
43
Ferritic/
austenitic
1.4462/ none/
S32205 2)
0.03
21-23
4.5-6.5
2.5-3.5
N 0.10-0.22
34
Ferritic/
austenitic
1.4410/none/
S 32750 4)
0.03
25
N 0.24-0.32
43
Microstructure
Designation
EN/ASTM/UNS
%
Carbon max.
%
Chromium
%
Nickel
%
Molybdenum
%
Other
PRE
Austenitic 1)
1.4308/CF8/ J92600
0.07
18-20
8-11
Austenitic 1)
1.4408/CF8M/ J92900
0.07
18-20
9-12
2-2.5
Austenitic 1)
1.4409/CF3M/ J92800
0.03
18-20
9-12
2-2.5
N max. 0.2
26
35
17
16
S 0.15-0.35
18
19
26
Austenitic
1.4584/none/ none
0.025
19-21
24-26
4-5
N max. 0.2
Cu 1-3
Ferritic/
Austenitic
1.4470/CD3MN/ J92205
0.03
21-23
4.5-6.5
2.5-3.5
N 0.12-0.2
35
Ferritic/
Austenitic
1.4517/CD4MCuN/
J93372
0.03
24.5-26.5
2.5-3.5
2.5-3.5
N 0.12-0.22
Cu 2.75-3.5
38
Contains some ferrite 2) Also known as SAF 2205, 3) Also known as 254 SMO,
Pitting Resistance Equivalent (PRE): Cr% + 3.3xMo% + 16xN%.
4)
Also known as SAF 2507
67
1.
Design
Section
Materials
Ferritic (magnetic)
Ferritic stainless steel is characterised by quite good
corrosion properties, very good resistance to stress
corrosion cracking and moderate toughness. Low alloyed
ferritic stainless steel is used in mild environments
(teaspoons, kitchen sinks, washing machine drums,
etc.) where it is a requirement that the component is
maintenance-free and non-rusting.
Martensitic (magnetic)
Martensitic stainless steel is characterised by high strength
and limited corrosion resistance. Martensitic steels are
used for springs, shafts, surgical instruments and for
sharp-edged tools, such as knives and scissors.
Austenitic (non-magnetic)
Austenitic stainless steel is the most common type
of stainless steel and is characterised by a high
corrosion resistance, very good formability, toughness
and weldability. Austenitic stainless steel, especially
the EN 1.4301 and EN 1.4401 are used for almost any
type of pump components in the industry. This kind of
stainless steel can be either wrought or cast.
EN 1.4305 is one of the most popular stainless steel types
of all the free machining stainless steel types. Due to its
high sulphur content (0.15-0.35 w%), the machinability has
improved considerably but unfortunately at the expense
of its corrosion resistance and its weldability. However,
over the years free machining grades with a low sulphur
content and thus a higher corrosion resistance have been
developed.
If stainless steel is heated up to 500C - 800C for a
longer period of time during welding, the chromium
might form chromium carbides with the carbon present in
the steel. This reduces chromiums capability to maintain
the passive film and might lead to intergranular corrosion
also referred to as sensitisation (see section 1.6.2).
If low carbon grades of stainless steel are used the risk of
sensitisation is reduced. Stainless steel with a low content
68
of carbon is referred to as EN 1.4306 (AISI 304L) or EN

1.4404 (AISI 316L). Both grades contain 0.03% of carbon
compared to 0.07% in the regular type of stainless steel
EN 1.4301 (AISI 304) and EN 1.4401 (AISI 316), see
illustration 1.6.17.
The stabilised grades EN 1.4571 (AISI 316Ti) contain a small
amount of titanium. Because titanium has a higher affinity
for carbon than chromium, the formation of chromium
carbides is minimised. The content of carbon is generally
low in modern stainless steel, and with the easy availability
of L grades the use of stabilised grades has declined
markedly.
Ferritic-austenitic or duplex (magnetic)

Ferritic-austenitic (duplex) stainless steel is characterised
by high strength, good toughness, high corrosion resistance
and excellent resistance to stress corrosion cracking and
corrosion fatigue in particular.
Ferritic-austenitic stainless steel is typically used in
applications that require high strength, high corrosion
resistance and low susceptibility to stress corrosion cracking
or a combination of these properties. Stainless steel
EN 1.4462 is widely used for making pump shafts and pump
housings.
Nickel alloys
Copper alloys
Nickel base alloys are defined as alloys in which nickel

is present in greater proportion than any other alloying
element. The most important alloying constituents are
iron, chromium, copper, and molybdenum. The alloying
constituents make it possible to form a wide range of
alloy classes. Nickel and nickel alloys have the ability to
withstand a wide variety of severe operating conditions,
for instance corrosive environments, high temperatures,
high stresses or a combination of these factors.
Pure copper has excellent thermal and electrical properties,

but is a very soft and ductile material.
Alloying additions result in different cast and wrought
materials, which are suitable for use in the production of
pumps, pipelines, fittings, pressure vessels and for many
marine, electrical and general engineering applications.
HastelloysTM alloys are a line of commercial alloys containing

Ni, Mo, Cr, and Fe. Nickel base alloys, such as InconelTM
Alloy 625, HastelloysTM C-276 and C-22 are highly corrosion
resistant and not subject to pitting or crevice corrosion in
low velocity seawater, and do not suffer from erosion at
high velocity.
The price of nickel base alloy limits its use in certain
applications. Nickel alloys are available in both wrought
and cast grades. However, nickel alloys are more difficult
to cast than the common carbon steels and stainless steel
alloys. Nickel alloys are especially used for pump parts in
the chemical process industry.
1) Lead can be added as an alloying element to improve

the machinability.
2) Bronze can be alloyed with aluminium to increase strength.
Fig 1.6.18: Common types of copper alloys
Brasses are the most widely used of the copper alloys

because of their low cost, their easy or inexpensive
fabrication and machining. However, they are inferior in
strength to bronzes and must not be used in environments
that cause dezincification (see selective corrosion).
Red brass, bronze and copper nickels in particular have,
compared to cast iron a high resistance to chlorides in
aggressive liquids, such as seawater. In such environments,
brass is unsuitable because of its tendency to dezincificate.
All copper alloys have poor resistance to alkaline liquids
(high pH), ammonia and sulfides and are sensitive to
erosion. Brass, red brass and bronze are widely used for
making bearings, impellers and pump housings.
69
1.
Design
Section
Materials
Aluminium
Designation
Major alloying element
1000-series
Unalloyed (pure) >99% Al
2000-series
Copper is the principal alloying element, though other

elements (magnesium) may be specified
3000-series
Manganese is the principal alloying element
4000-series
Silicon is the principal alloying element
5000-series
Magnesium is the principal alloying element
6000-series
Magnesium and silicon are principal alloying elements
7000-series
Zinc is the principal alloying element, but other elements,

such as copper, magnesium, chromium, and zirconium
may be specified
8000-series
Other elements (including tin and some lithium

compositions)
Titanium
CP: commercial pure (titanium content above 99.5%)
Fig 1.6.20: Titanium grades and alloy characteristics
Fig 1.6.19: Major alloying elements of aluminium
Pure aluminium is a light and soft metal with a density

of about a third of that of steel. Pure aluminium has a
high electrical and thermal conductivity. The most common
alloying elements are silicon (silumin), magnesium, iron and
copper. Silicon increases the materials castability, copper
increases its machinability and magnesium increases its
corrosion resistance and strength.
The obvious advantages of aluminium are that the material
naturally generates a protective oxide film and is highly
corrosion resistant if it is exposed to the atmosphere.
Treatment, such as anodising, can further improve this
property. Aluminium alloys are widely used in structures
where a high strength to weight ratio is important, such
as in the transportation industry. For example, the use of
aluminium in vehicles and aircrafts reduces weight and
energy consumption.
On the other hand, the disadvantage of aluminium is that
it is not stable at low or high pH and in chloride-containing
environments. This property makes aluminium unsuitable for
exposure to aqueous solutions especially under conditions
with high flow. This is further emphasised by the fact that
aluminium is a reactive metal, i.e. has a low position in the
galvanic series (see galvanic corrosion) and may easily suffer
from galvanic corrosion if coupled to nobler metals and
alloys.
70
Pure titanium has a low density, is quite ductile and has a

relatively low strength. However, when a limited amount
of oxygen is added it will strengthen titanium and produce
the so-called commercial-pure grades. Additions of various
alloying elements, such as aluminium and vanadium
increase its strength significantly, at the expense of
ductility. The aluminium and vanadium alloyed titanium
(Ti-6Al-4V) is the workhorse alloy of the titanium
industry. It is used in many aerospace engine and airframe
components. Because titanium is a high-price material, it
is not yet a material which is often used for making pump
components.
Titanium is a very reactive material. As it is the case for
stainless steel, titaniums corrosion resistance depends on
the formation of an oxide film. However, the oxide film
is more protective than that on stainless steel. Therefore,
titanium performs much better than stainless steel in
aggressive liquids, such as seawater, wet chlorine or
organic chlorides, that cause pitting and crevice corrosion.
1.6.4 Ceramics
Thermoplastics
Ceramic materials are defined as inorganic, non-metallic

materials, which are typically crystalline in nature. They
are composed of metallic and non-metallic elements.
Common technical ceramics are aluminium oxide (alumina
- Al2O3), silicon carbide (SiC), tungsten carbide (WC), and
silicon nitride (Si3N4).
Thermoplastic polymers consist of long polymer molecules

that are not linked to each other, i.e. have no cross-links.
They are often supplied as granules and heated to permit
fabrication by methods, such as moulding or extrusion.
A wide range is available, from low-cost commodity plastics
(e.g. PE, PP, PVC) to high cost engineering thermoplastics
(e.g. PEEK) and chemical resistant fluoropolymers (e.g.
PTFE, PVDF). PTFE is one of the few thermoplastics, which
is not melt-processable. Thermoplastics are widely used
for making pump housings or for lining of pipes and pump
housings.
Ceramics are suitable for applications which require high

thermal stability, high strength, high wear resistance, and
high corrosion resistance. The disadvantage of ceramics is
the low ductility and high tendency for brittle fractures.
Ceramics are mainly used for making bearings and seal
faces for shaft seals.
1.6.5 Plastics
Abbreviation
Polymer name
PP
PE
PVC
PEEK
PVDF
PTFE*
Polypropylene
Polyethylene
Polyvinylchloride
Polyetheretherketone
Polyvinylidene fluoride
Polytetrafluoroethylene
*Trade name: Teflon
Thermosets
Thermosets harden permanently when heated, as crosslinking hinders bending and rotations. Cross-linking is
achieved during fabrication using chemicals, heat, or
radiation; this process is called curing or vulcanization.
Thermosets are harder, more dimensionally stable, and
more brittle than thermoplastics and cannot be remelted.
Important thermosets include epoxies, polyesters,
and polyurethanes. Thermosets are among other things
used for surface coatings.
Fig 1.6.21: Overview of polymer names
Some plastics are derived from natural substances, such as

plants, but most types are man-made. These are known as
synthetic plastics. Most synthetic plastics come from crude
oil, but coal and natural gas are also used.
There are two main types of plastics: Thermoplastics and
thermosets (thermosetting plastics). The thermoplastics
are the most common kind of plastic used worldwide.
Plastics often contain additives, which transfer certain
additional properties to the material. Furthermore,
plastics can be reinforced with fiberglass or other fibres.
These plastics together with additives and bres are also
referred to as composites.
Examples of additives found in plastics
Inorganic fillers for mechanical reinforcement
Chemical stabilisers, e.g. antioxidants
Plasticisers
Flame retardants
Linear polymer chains
Thermoplastics
Branched polymer chains
Elastomers
Weakly cross-linked polymer chains
Thermosets
Strongly cross-linked polymer chains
Fig 1.6.22: Different types of polymers
71
1. Design
Section
1.6
of pumps and motors
Materials
1.6.6 Rubber
of
Abbreviation Common types
Common
ofname
copper alloys Examples
trade name
NBR
Nitrile rubber
Buna-NR
EPDM, EPM
Ethylene propylene rubber
NordelR
FKM
Fluoroelastomers
VitonR
MQ, VMQ, PMQ, FMQ
Silicone rubber
SilopreneR
FFKM
Perfluoroelastomers
ChemrazR
KalrezR
Fig 1.6.23: Rubber types
The term rubber includes both natural rubber and

synthetic rubber. Rubbers (or elastomers) are flexible longchain polymers that can be stretched easily to several times
their unstretched length and which rapidly return to their
original dimensions when the applied stress is released.
Rubbers are cross-linked (vulcanized), but have a low crosslink density, see figure 1.6.22. The cross-link is the key to
the elastic, or rubbery, properties of these materials. The
elasticity provides resiliency in sealing applications. Different
components in a pump are made of rubber, e.g. gaskets
and O-rings (see section 1.3 on shaft seals). In this section we
will present the different kinds of rubber qualities and their
main properties as regards temperature and resistance to
different kinds of liquid groups.
At temperatures up to about 100C nitrile rubber is an

inexpensive material that has a high resistance to oil and
fuel. Different grades exist - the higher the acrylonitrile
(ACN) content, the higher the oil resistance, but the poorer
is the low temperature flexibility. Nitrile rubbers have high
resilience and high wear resistance but only moderate
strength. Further, the rubber has limited weathering
resistance and poor solvent resistance. It can generally be
used down to about -30C, but certain grades can operate
at lower temperatures.
72
Ethylene propylene has excellent water resistance which

is maintained to high temperatures approximately 120140C. The rubber type has good resistance to acids, strong
alkalis and highly polar fluids, such as methanol and
acetone. However, it has very poor resistance to mineral
oil and fuel.
Fluoroelastomers cover a whole family of rubbers designed
to withstand oil, fuel and a wide range of chemicals
including non-polar solvents.
offers excellent
resistance to high temperature operation (up to 200C
depending on the grade) in air and different types of oil.
rubbers have limited resistance to steam, hot water,
methanol, and other highly polar fluids. Further, this type
of rubber has poor resistance to amines, strong alkalis
and many freons. There are standard and special grades
- the latter have special properties, such as improved lowtemperature or chemical resistance.
Silicone rubbers have outstanding properties, such as low

compression set in a wide range of temperatures (from
-60C to 200C in air), excellent electrical insulation and
are non-toxic. Silicone rubbers are resistant to water,
some acids and oxidizing chemicals. Concentrated acids,
alkalines, and solvents should not be used with silicone
rubbers. In general, these types of rubber have poor
resistance to oil and fuel. However, the resistance of FMQ
silicone rubber to oil and fuel is better than that of the
silicone rubber types MQ, VMQ, and PMQ.
Perfluoroelastomers have very high chemical resistance,

almost comparable to that of PTFE (polytetrafluorethylene,
e.g. TeflonR). They can be used up to high temperatures,
but their disadvantages are difficult processing, very high
cost and limited use at low temperatures.
1.6.7 Coatings
Protective coating metallic, non-metallic (inorganic)
or organic is a common method of corrosion control. The
main function of coatings is (aside from galvanic coatings,
such as zinc) to provide an effective barrier between the
metal (substrate) and its environment. They allow the use
of normal steel or aluminium instead of more expensive
materials. In the following section we will examine
the possibilities of preventing corrosion by means of
different coatings:
Metallic and non-metallic (inorganic) coatings and organic
coatings.
To protect the base steel,

zinc coating sacrifices itself
slowly by galvanic action.
Steel coated with a more noble

metal, such as nickel, corrodes
more rapidly if the coating
is damaged.
Fig 1.6.24: Galvanic vs. barrier corrosion protection
Metallic coatings
Metallic coatings less noble than the substrate
Zinc coatings are commonly used for the protection of
steel structures against atmospheric corrosion. Zinc has
two functions: it acts as a barrier coating and it provides
galvanic protection. Should an exposed area of steel
occur, the zinc surface preferentially corrodes at a slow
rate and protects the steel. The preferential protection
is referred to as cathodic protection. When damage is
small, the protective corrosion products of zinc will fill the
exposed area and stop the attack.
Metallic coatings nobler than the substrate

Electroplating of nickel and chromium coatings on steel
are examples of metallic coatings that are nobler than
the substrate. Unlike galvanic coatings where the coating
corrodes near areas where the base metal is exposed,
any void or damage in a barrier coating can lead to an
immediate base metal attack.
73
1.
Design
Section
<
Materials
(inorganic coatings)
Conversion coatings are an important category of nonmetallic coatings (inorganic).
Conversion coatings
Conversion coatings are formed by a controlled corrosion
reaction of the substrate in an oxidised solution.
Well-known examples of conversion coatings are anodising
or chromating of aluminium, and phosphate treatment of
steel. Anodising is mainly used for surface protection of
aluminium, while chromating and phosphating are usually
used for pre-treatment in connection with painting.
Besides improving paint adhesion, it helps to prevent the
spreading of rust under layers of paint.
Paints
As mentioned above, paints are an important class of
organic coating. Figure 1.6.25 shows several types of
organic coatings. A typical paint formulation contains
polymeric binders, solvents, pigments and additives. For
environmental reasons, organic solvents are increasingly
being replaced by water or simply eliminated, e.g powder
coating. Painted metal structures usually involve two or
more layers of coating applied on a primary coating, which
is in direct contact with the metal.
Organic coatings
Organic coatings contain organic compounds and are
available in a wide range of different types. Organic coatings
are applied to the metal by methods of spraying, dipping,
brushing, lining or electro-coating (paint applied by means
of electric current) and they may or may not require
heat-curing. Both thermoplastic coatings, such as
polyamide, polypropylene, polyethylene, PVDF and PTFE and
elastomer coatings are applied to metal substrates to
combine the mechanical properties of metal with the
chemical resistance of plastics but paints are by far the
most widely used organic coating.
74
Physical states of common organic coatings

Resin
type
Acrylic
Alkyd
Epoxy
Polyester
Polyurethane
Vinyl
Solvent- Water- Powder

based
based coating
X
X
X
X
X
X
X
X
X
X
X
Two comp.
liquid
X
X
X
X
X
Fig 1.6.25: Physical states of common organic coatings
X
X
X
Chapter 2. Installation and performance reading
Section 2.1: Pump installation

2.1.1
2.1.2
2.1.3
2.1.4
2.1.5
New installation
Existing installation
Pipe ow for single-pump installation
Limitation of noise and vibrations
Sound level (L)
Section 2.2: Pump performance

2.2.1 Hydraulic terms
2.2.2 Electrical terms
2.2.3 Liquid properties
Section 2.1
Pump installation
Correct advice and selection of pump type for an installation

has larger implication than what meets the eye. The
larger the pumps, the greater the costs with respect
to investment, installation, commissioning, running
and maintenance basically the life cycle cost (LCC). An
extensive product portfolio combined with competent
advice and after-sales service is the foundation of a correct
selection. The following analysis, recommendations and
hints are general for any installation, but to a greater
extent relevant for medium-sized and large installations.
We will present our recommendations for two types of
installation: New and existing installations.
2.1.2 Existing installation replacement

The following five steps will help you make an optimum
pump selection for an existing installation:
Pre-investigation of the installation should include

the following considerations:
Basic pipe flow pipes in and out of the building, e.g.
from ground, along floor or from ceiling
Specific pipework at the point of installation, e.g.

in-line or end-suction, dimensions, manifolds
Space available width, depth and height

Accessibility in connection with installation and
2.1.1 New installation

If the pipework has not been planned yet, you can base
the selection of pump type on other primary selection
criteria, e.g. efficiency, investment costs or life cycle
costs (LCC). This will not be covered in this
section. However, the general guidelines, which are
presented, also apply for pipework that has not yet
been planned.
If the pipework has already been planned, the selection

of pump is equivalent to replacing a pump in an existing
installation.
maintenance, for instance doorways

Availability of lifting equipment or alternatively
accessibility of such equipment
Floor type, e.g. solid or suspended floor with basement
Existing foundation
Existing electric installation
Previous pump installation

Pump make, type, specifications including old duty
point, shaft seal, materials, gaskets, controlling
History, e.g. lifetime, maintenance
Future requirements
Desired improvements and benefits
New selection criteria including duty points and
operating times, temperature, pressure, liquid
specifications
Supplier criteria, e.g. availability of spare parts
Advisory
Major changes might be beneficial in a long or short
term or both and must be documented, e.g. installation
savings, life cycle costs (LCC), reduction on environmental
impact like noise and vibrations and accessibility in
connection with maintenance
Selection
Must be based on a customer-agreed list of priorities
For the selection of the correct pump type and advice on
installation, two main areas are important: Pipe flow and
limitation of noise and vibrations. These two areas will
be dealt with on the following pages.
76
2.1.3 Pipe flow for single-pump installation

Figure 2.1.1 is based on single-pump installation. In parallel installations accessibility plays a
major role for how good a pump choice is.
The evaluation criterion is as simple pipework as possible, hence as few bends as possible.
Scores:
Best choice
Good choice
Least good choice
Not applicable
Pump type
Pipework
To the pump:
Along floor
From ground
From ceiling
Wallmounted
A. In-line close-coupled
(horizontal or vertical
mounting)
B. End-suction close- coupled

(horizontal or vertical
mounting)
C. End-suction long-coupled
(only horizontal mounting)
From the pump:

Along floor
Best choice
Good choice
Good choice
To ground
Best choice
Good choice
Good choice
To ceiling
Good choice
Best choice
Best choice
Along floor
Good choice
Best choice
Least good choice
To ground
Good choice
Best choice
Least good choice
To ceiling
Good choice
Best choice
Best choice
Along floor
Best choice
Least good choice
Least good choice
To ground
Best choice
Good choice
Good choice
To ceiling
Good choice
Best choice
Best choice
Wallmounted
Best choice
Good choice
Not applicable
Fig. 2.1.1 Pipework and pump type
77
Section 2.1
Pump installation
Accessibility plays a major role in how well a specific pump

choice is in connection with installation of several pumps
in parallel. The accessibility is not always easy for in-line
pumps installed in parallel because of the pipework, see
figure 2.1.2. As it appears from figure 2.1.3, end-suction
pumps installed in parallel provide easier accessibility.
2.1.4 Limitation of noise and vibrations
Fig. 2.1.2:
3 in-line pumps in parallel; limited maintenance
access because of pipework
To achieve optimum operation and minimise noise and

vibration, it may be necessary to consider vibration
dampening of the pump in certain cases. Generally, this
should always be considered in the case of pumps with
motors above 7.5 kW. Smaller motor sizes, however, may
also cause undesirable noise and vibration. Noise and
vibration are generated by the rotation in motor and
pump and by the flow in pipes and fittings. The effect
on the environment depends on correct installation and
the state of the entire system. Below we will present 3
different ways of limiting noise and vibration in a pump
installation: Foundation, dampeners and expansion joint.
Fig. 2.1.3:
3 end-suction pumps in parallel; easier maintenace access
because of pipework
Floor
Solid ground
Foundation
Floor constructions can be divided into two types: Solid
floor and suspended floor.
Fig. 2.1.4: Solid floor construction
Solid minimum risk of noise due to bad

transmission of vibrations, see figure 2.1.4.
Suspended risk of floor amplifying the noise.
Basement can act as a resonance box,
see figure 2.1.5.
Ground oor
Wall
The pump should be installed on a plane and rigid surface.

Four basic ways of installation exist for the two types
of floor construction: Floor, plinth, floating plinth and
foundation suspended on vibration dampeners.
Basement
Floor
Solid ground
Fig. 2.1.5: Suspended floor construction
78
Floor
Fig. 2.1.6: Floor
Floor
Direct mounting on floor, hence direct vibration
transmission, see figure 2.1.6.
Floor
Plinth
Poured directly on concrete floor, hence as floor, see
figure 2.1.7.
Fig. 2.1.7: Plinth
Floor
Floating plinth
Resting on a dead material, e.g. sand, hence
reduced risk of vibration transmission, see figure 2.1.8.
Base plate Pump unit
Plinth Base plate Pump unit
Fig. 2.1.8:
Floating plinth
Floor Sand Plinth Base plate Pump unit
Foundation suspended on vibration dampeners

Optimum solution with controlled vibration
transmission, see figure 2.1.9.
Fig. 2.1.9: Foundation

suspended on
vibration dampeners
As a rule of thumb, the weight of a concrete foundation

should be 1.5 x the pump weight. This weight is needed to
get the dampeners to work efficiently at low pump speed.
Floor
Vibration dampeners Foundation Base plate Pump unit
Pump unit
Fig. 2.1.10: The same
foundation rules go
for vertical in-line
pumps
Foundation
Vibration
dampeners
Floor
79
Section 2.1
Pump installation
Dampeners
The selection of the right vibration dampener requires
the following data:
Forces acting on the dampener

Motor speed considering speed control, if any
Required dampening in % (suggested value is 70%)
The determination of the right dampener varies from
installation to installation but a wrong selection of
dampener may increase the vibration level in certain cases.
The supplier should therefore size vibration dampeners.
Pumps installed with vibration dampeners must always
have expansion joints fitted at both the suction and the
discharge side. This is important in order to avoid that the
pump hangs in the flanges.
Expansion
joint
Foundation
Pump unit
Base plate
Vibration
dampeners
Floor
Fig. 2.1.11: Installation with expansion joints, vibration dampeners and

fixed pipework
Expansion joints
Expansion joints are installed to:
absorb expansions/contractions in the pipework

caused by changing liquid temperature
reduce mechanical strains in connection with pressure

waves in the pipework
isolate mechanical noise in the pipework (not for metal

bellows expansion joints)
Expansion joints must not be installed to compensate for
inaccuracies in the pipework, such as centre displacement
or misalignment of flanges.
Expansion joints are fitted at a distance of minimum 1 to
1.5 . DN diameter from the pump on the suction side as well
as on the discharge side. This prevents the development of
turbulence in the expansion joints, resulting in better suction
conditions and a minimum pressure loss on the pressure
side. At high water velocities (>5 m/s) it is best to install
larger expansion joints corresponding to the pipework.
80
Figures 2.1.12-2.1.14 show examples of rubber bellows

expansion joints with or without tie bars.
Fig. 2.1.12: Rubber bellows

expansion joints with tie bars
Expansion joints with tie bars can be used to minimise the

forces caused by the expansion joints. Expansion joints
with tie bars are recommended for sizes larger than DN 100.
An expansion joint without tie bars will exert force on
the pump flanges. These forces affect the pump and the
pipework.
Fig. 2.1.13: Rubber

bellows expansion
joints without tie
bars
The pipes must be fixed so that they do not stress the

expansion joints and the pump, see figure 2.1.11. The fix
points should always be placed as close to the expansion
joints as possible. Follow the expansion joint suppliers
instructions.
Fig. 2.1.14: Metal

bellows expansion
joints with tie bars
At temperatures above 100C combined with a high pressure,

metal bellows expansion joints are often preferred due to
the risk of rupture.
2.1.5 Sound level (L)

The sound level in a system is measured in decibel (dB).
Noise is unwanted sound. The level of noise can be
measured in the following three ways:
1. Pressure Lp : The pressure of the air waves
2. Power LW : The power of the sound
3. Intensity - LI: The power per m2 (will not be
covered in this book)
It is not possible to compare the three values directly, but it
is possible to calculate between them based on standards.
The rule of thumb is:
Lp (dB)
120
100
Pain threshold
Threshold of hearing
Music
80
60
Speech
40
20
0
20
50 100 200 500Hz 1
Fig. 2.1.15: Threshold of hearing vs. frequency
10 20kHz
Frequency
kHz
Smaller pumps, e.g. 1.5 kW: Lw = LP + 11 dB

Larger pumps, e.g. 110 kW: Lw = LP + 16 dB
81
Section 2.1
Pump installation
The EU Machine Directive prescribes that sound levels

have to be indicated as pressure when they are below 85
dB(A) and as power when they exceed 85 dB(A).
Noise is subjective and depends on a persons ability
to hear, e.g. young vs. old person. Therefore, the abovementioned measurements get weight according to
the sensibility of a standard ear, see figure 2.1.15. The
weighting is known as A-weighting (dB(A)), expressed as
e.g: LpA, and the measurements are adjusted depending on
frequency. In some cases it increases and in other cases it
decreases, see figure 2.1.16. Other weightings are known
as B and C but they are used for other purposes, which we
do not cover in this book.
dB (A)
10
0
-10
-20
-30
-40
-50
-60
-70
-80
100
10
10000 Hz
1000
Fig. 2.1.16 A-weighting curve
15
In case of two or more pumps in operation, the sound level

can be calculated. If it is pumps with the same sound level
the total sound level can be calculated adding the value
from figure 2.1.17, e.g. 2 . pumps is Lp + 3 dB, 3 . pumps is
Lp + 5 dB. If the pumps have different sound level, values
from figure 2.1.18 can be added.
Indications of sound level should normally be stated as
free field conditions over reflecting surface, meaning the
sound level on a hard floor with no walls. Guaranteeing
values in a specific room in a specific pipe system is
difficult because these values are beyond the reach of the
manufacturer. Certain conditions could have a negative
impact (increasing sound level) or a positive impact
on the sound level. Recommendations to installation
and foundation can be given to eliminate or reduce the
negative impact.
10
12
16
20
24
Fig. 2.1.17 Increase of the total sound pressure level with

equal sources
3
2.5
2
Experience values:
Rise of
+ 3dB
+ 5dB
+10dB
Perceived as:
Just noticeable
Clearly noticeable
Twice as loud
1.5
1
0.5
10
Fig. 2.1.18 Increase of the total sound pressure level with

different sources
82
Chapter 3. System hydraulic
Section 3.1: System characteristics

3.1.1 Single resistances
3.1.2 Closed and open systems
Section 3.2: Pumps connected in series and parallel

3.2.1 Pumps in parallel
3.2.2 Pumps connected in series
Section 3.1
System characteristics
Previously, in section 1.1.2 we discussed the basic

characteristics of pump performance curves. In this
chapter we will examine the pump performance curve at
different operating conditions as well as a typical system
characteristic. Finally, we will focus on the interaction
between a pump and a system.
A systems characteristic describes the relation between the
flow Q and head H in the system. The system characteristic
depends on the type of system in question. We distinguish
between two types: Closed and open systems.
Closed systems
are circulating systems like heating or air-conditioning
systems, where the pump has to overcome the friction
losses in the pipes, fittings, valves, etc. in the system.
Open systems
are liquid transport systems like water supply systems. In
such systems the pump has to deal with both the static
head and overcome the friction losses in the pipes and
components.
When the system characteristic is drawn in the same
system of co-ordinates as the pump curve, the duty point
of the pump can be determined as the point of intersection
of the two curves, see figure.3.1.1.
Open and closed systems consist of resistances (valves,
pipes, heat exchanger, etc.) connected in series or
parallel, which altogether affect the system characteristic.
Therefore, before we continue our discussion on open
and closed systems, we will briefly describe how these
resistances affect the system characteristic.
96
Fig. 3.1.1: The point of intersection between the pump curve and the system
characteristic is the duty point of the pump
3.1.1 Single resistances

Every component in a system constitutes a resistance
against the liquid flow which leads to a head loss across
every single component in the system. The following
formula is used to calculate the head loss H:
H = k . Q2
k is a constant, which depends on the component in
question and Q is the flow through the component. As it
appears from the formula, the head loss is proportional to
the flow in second power. So, if it is possible to lower the
flow in a system, a substantial reduction in the pressure
loss occurs.

The total head loss in a system consisting of several
components connected in series is the sum of head losses
that each component represents. Figure 3.1.2 shows a
system consisting of a valve and a heat exchanger. If we
do not consider the head loss in the piping between the
two components, the total head loss Htot is calculated by
adding the two head losses:
Htot = H1 + H2
Furthermore, figure 3.1.2 shows how the resulting curve
will look and what the duty point will be if the system
is a closed system with only these two components. As
it appears from the figure, the resulting characteristic
is found by adding the individual head losses H at a
given flow Q. Likewise, the figure shows that the more
resistance in the system, the steeper the resulting system
curve will be.
Fig. 3.1.2: The head loss for two components connected in series
is the sum of the two individual head losses
97
Section 3.1
Resistances connected in parallel

Contrary to connecting components in series, connecting
components in parallel result in a more flat system
characteristic. The reason is that components installed
in parallel reduce the total resistance in the system and
thereby the head loss.
The differential pressure across the components connected
in parallel is always the same. The resulting system
characteristic is defined by adding all the components
individual flow rate for a specific H. Figure 3.1.3 shows
a system with a valve and a heat exchanger connected in
parallel.
The resulting flow can be calculated by the following
formula for a head loss equivalent to H
Q tot = Q 1 + Q2
Fig. 3.1.3: Components connected in parallel reduce the resistance in
the system and result in a more flat system characteristic
3.1.2 Closed and open systems

As mentioned previously, pump systems are split into two
types of basic systems: Closed and open systems. In this
section, we will examine the basic characteristics of these
systems.
Closed systems
Typically, closed systems are systems, which transport
heat energy in heating systems, air-conditioning systems,
process cooling systems, etc. A common feature of these
types of closed systems is that the liquid is circulated and
is the carrier of heat energy. Heat energy is in fact what the
system has to transport.
Closed systems are characterised as systems with pumps
that only have to overcome the sum of friction losses,
which are generated by all the components. Figure 3.1.4
shows a schematic drawing of a closed system where
a pump has to circulate water from a heater through a
control valve to a heat exchanger.
98
Fig. 3.1.4: Schematic drawing of a closed system
All these components together with the pipes and fittings

result in a system characteristic as the one shown in figure
3.1.5. The required pressure in a closed system (which the
system curve illustrates) is a parabola starting in the point
(Q,H) = (0,0) and is calculated by the following formula:
H = k . Q2
As the formula and curve indicate, the pressure loss is
approaching zero when the flow drops.
Open systems
Fig. 3.1.5: The system characteristic for a closed system is a

parabola starting in point (0,0)
Open systems are systems, where the pump is used to

transport liquid from one point to another, e.g. water
supply systems, irrigation systems, industrial process
systems. In such systems the pump has to deal with
both the geodetic head of the liquid and to overcome the
friction losses in the pipes and the system components.
We distinguish between two types of open system:
Open systems where the total required geodetic lift
is positive.
Open systems where the total required geodetic lift
is negative.
Fig. 3.1.6: Open system with positive geodetic lift
Open system with positive geodetic head Figure

3.1.6 shows a typical open system with positive geodetic
lift. A pump has to transport water from a break tank at
ground level up to a roof tank on the top of a building.
First of all, the pump has to provide a head higher than
the geodetic head of the water (h). Secondly, the pump
has to provide the necessary head to overcome the total
friction loss between the two tanks in piping, fittings,
valves, etc. (Hf). The pressure loss depends on the amount
of flow, see figure 3.1.7.
Q1
Q1
Fig. 3.1.7: System characteristic together with the pump performance

curve for the open system in figure 3.1.6
99
Section 3.1
The figure shows that in an open system no water flows

if the maximum head (Hmax) of the pump is lower than
the geodetic head (h). Only when H > h, water will start
to flow from the break tank to the roof tank. The system
curve also shows that the lower the flow rate, the lower
the friction loss (Hf) and consequently the lower the power
consumption of the pump.
So, the flow (Q1) and the pump size have to match the
need for the specific system. This is in fact a rule-ofthumb for liquid transport systems: A larger flow leads
to a higher pressure loss, whereas a smaller flow leads to
a smaller pressure loss and consequently a lower energy
consumption.
Fig. 3.1.8: Open system with negative geodetic lift
Open system with negative geodetic lift

A typical example of an open system with negative
required head is a pressure booster system, e.g. in a water
supply system. The geodetic head (h) from the water tank
brings water to the consumer - the water flows, although
the pump is not running. The difference in height between
the liquid level in the tank and the altitude of the water
outlet (h) results in a flow equivalent to Qo. However, the
head is insufficient to ensure the required flow (Q1) to the
consumer. Therefore, the pump has to boost the head to
the level (H1) in order to compensate for the friction loss
(Hf) in the system. The system is shown in figure 3.1.8
and the system characteristic together with the pump
performance curve are shown in figure 3.1.9.
The resulting system characteristic is a parabolic curve
starting at the H-axes in the point (0,-h).
The flow in the system depends on the liquid level in the
tank. If we reduce the water level in the tank the height (h)
is reduced. This results in a modified system characteristic
and a reduced flow in the system, see figure 3.1.9.
100
Fig. 3.1.9: System characteristic together with the pump

performance curve for the open system in gure 3.1.8
Section 3.2
Pumps connected in series and parallel
To extend the total pump performance in a system, pumps

are often connected in series or parallel. In this section we
will concentrate on these two ways of connecting pumps.
3.2.1 Pumps in parallel

Pumps connected in parallel are often used when
the required flow is higher than what one single pump
can supply
the system has variable flow requirements and when
these requirements are met by switching the parallelconnected pumps on and off.
Normally, pumps connected in parallel are of similar type
and size. However, the pumps can be of different size, or
one or several pumps can be speed-controlled and thereby
have different performance curves.
To avoid bypass circulation in pumps, which are not
running, a non-return valve is connected in series with
each of the pumps. The resulting performance curve
for a system consisting of several pumps in parallel is
determined by adding the flow, which the pumps deliver
at a specific head.
Fig. 3.2.1: Two pumps connected in parallel with similar

performance curves
Figure 3.2.1 shows a system with two identical pumps

connected in parallel. The systems total performance
curve is determined by adding Q1 and Q2 for every value of
head which is the same for both pumps, H1=H2 .
Because the pumps are identical the resulting pump curve
has the same maximum head Hmax but the maximum flow
Qmax is twice as big. For each value of head the flow is the
double as for a single pump in operation:
Q = Q1 + Q2 = 2 Q1 = 2 Q2
101
Section 3.2
Pumps connected in series and parallel
Figure 3.2.2 shows two different sized pumps connected in

parallel. When adding Q1 and Q2 for a given head H1=H2, the
resulting performance curve is defined. The hatched area
in figure 3.2.2 shows that P1 is the only pump to supply in
that specific area, because it has a higher maximum head
than P2.
Speed-controlled pumps connected in parallel

The combination of pumps connected in parallel and
speed-controlled pumps is a very useful way to achieve
efficient pump performance when the flow demand varies.
The method is common in connection with water supply /
pressure boosting systems. Later in chapter 4, we will
discuss speed-controlled pumps in detail.
Fig 3.2.2: Two pumps connected in parallel with unequal

performance curves
A pumping system consisting of two speed-controlled

pumps with the same performance curve covers a wide
performance range, see figure 3.2.3.
One single pump is able to cover the required pump
performance up until Q1. Above Q1 both pumps have to
operate to meet the performance needed. If both pumps
are running at the same speed the resulting pump curves
look like the orange curves shown in figure 3.2.3.
Please note that the duty point indicated at Q1 is obtained
with one pump running at full speed. However, the
duty point can also be achieved when two pumps are
running at reduced speed. This situation is shown in figure
3.2.4 (orange curves). The figure also compares the two
situations with regard to efficiency. The duty point for
one single pump running at full speed results in a bad
pump efficiency mainly because the duty point is located
far out on the pump curve. The total efficiency is much
higher when two pumps run at reduced speed, although
the maximum efficiency of the pumps decreases slightly
at reduced speed.
Even though one single pump is able to maintain the
required flow and head, it is sometimes necessary due
to efficiency and thus energy consumption to use both
pumps at the same time. Whether to run one or two
pumps depend on the actual system characteristic and the
pump type in question.
102
Fig. 3.2.3: Two speed-controlled pumps connected in parallel (same size).

The orange curve shows the performance at reduced speed
Fig. 3.2.4: One pump at full speed compared to two pumps at reduced
speed. In this case the two pumps have the highest total efficiency
3.2.2. Pumps connected in series

Normally, pumps connected in series are used in
systems where a high pressure is required. This is also
the case for multistage pumps which are based on the
series principle, i.e. one stage equals one pump. Figure
3.2.5 shows the performance curve of two identical
pumps connected in series. The resulting performance
curve is made by marking the double head for each
flow value in the system of co-ordinates. This results
in a curve with the double maximum head (2Hmax) and
the same maximum flow (Qmax) as each of the single
pumps.
Fig. 3.2.5: Two equal sized pumps connected in series
Figure 3.2.6 shows two different sized pumps connected

in series. The resulting performance curve is found by
adding H1 and H2 at a given common flow Q1=Q2.
The hatched area in figure 3.2.6 shows that P2 is the
only pump to supply in that specific area because it has
a higher maximum flow than P1.
As discussed in section 3.2.1, unequal pumps can be
a combination of different sized pumps or of one or
several speed-controlled pumps. The combination of
a fixed speed pump and a speed-controlled pump
connected in series is often used in systems where a
high and constant pressure is required. The fixed speed
pump supplies the liquid to the speed-controlled pump,
whose output is controlled by a pressure transmitter
PT, see figure 3.2.7.
Q
Fig. 3.2.6: Two different sized pumps connected in series
Fig. 3.2.7: Equal sized fixed speed pump and speed-controlled pump
connected in series. A pressure transmitter PT together with a speed
controller is making sure that the pressure is constant at the outlet of P2.
103
Chapter 4. Performance adjustment of pumps
Section 4.1: Adjusting pump performance

4.1.1 Throttle control
4.1.2 Bypass control
4.1.3 Modifying impeller diameter
4.1.4 Speed control
4.1.5 Comparison of adjustment methods
4.1.6 Overall efciency of the pump system
4.1.7 Example: Relative power consumption when the ow
is reduced by 20%
Section 4.2: Speed-controlled pump solutions

4.2.1 Constant pressure control
4.2.2 Constant temperature control
4.2.3 Constant differential pressure in a circulating system
4.2.4 Flow-compensated differential pressure control
Section 4.3: Advantages of speed control
Section 4.4: Advantages of pumps with integrated

frequency converter
4.4.1 Performance curves of speed-controlled pumps
4.4.2 Speed-controlled pumps in different systems
Section 4.5: Frequency converter

4.5.1 Basic function and characteristics
4.5.2 Components of the frequency converter
4.5.3 Special conditions regarding frequency converters
Section 4.1
When selecting a pump for a given application it is

important to choose one where the duty point is in the
high-efficiency area of the pump. Otherwise, the power
consumption of the pump is unnecessarily high see figure
4.1.1.
H
[m]
50
40
70
60
50
30
However, sometimes it is not possible to select a pump that

fits the optimum duty point because the requirements of
the system change or the system curve changes over time.
20
10
0
Therefore, it can be necessary to adjust the pump

performance so that it meets the changed requirements.
The most common methods of changing pump
performance are:
Throttle control
Bypass control
Speed control
Choosing a method of adjusting the pump performance is

based on an evaluation of the initial investment together
with the operating costs of the pump. All methods can be
carried out continuously during operation apart from the
modifying impeller diametermethod. Often, oversized
pumps are selected for the system and therefore it is
necessary to limit the performance first of all, the flow
rate and in some applications the maximum head.
On the following pages you can read about the four
adjusting methods.
106
10
20
30
40
50
60
70
40
30
20
10
0
80 Q [m3/h]
Fig.: 4.1.1: When selecting a pump it is important to choose a pump

where the duty point is within the high efciency area.
4.1.1 Throttle control

Hp
A throttle valve is placed in series with the pump making it

possible to adjust the duty point. The throttling results in a
reduction of flow, see figure 4.1.2. The throttle valve adds
resistance to the system and raises the system curve to a
higher position. Without the throttle valve, the flow is Q2.
With the throttle valve connected in series with the pump,
the flow is reduced to Q1.
Throttle valve
System
Hv
Hs
H
Pump
Throttle valves can be used to limit the maximum flow. By

adding the valve, the maximum possible flow in the system
is limited. In the example, the flow will never be higher than
Q3, even if the system curve is completely flat meaning no
resistance at all in the system. When the pump performance
is adjusted by the throttling method, the pump will deliver a
higher head than necessary for that particular system.
Resulting characteristic
Smaller pump
System
Hv
Throttle valve
Hs
Q1
Q2
Q3
Fig.: 4.1.2: The throttle valve increases the resistance in the system
and consequently reduces the ow.
If the pump and the throttle valve are replaced by a smaller

pump, the pump will be able to meet the wanted flow Q1,
but at a lower pump head and consequently a lower power
consumption, see gure 4.1.2.
4.1.2 Bypass control
Bypass valve
QBP
Instead of connecting a valve in series with the pump, a

bypass valve across the pump can be used to adjust the
pump performance, see figure 4.1.3.
Compared to the throttle valve, installing a bypass valve
will result in a certain minimum flow QBP in the pump,
independent on the system characteristics. The flow QP is
the sum of the flow in the system QS and the flow in the
bypass valve QBP.
QP
QS
System
HP
H
Bypass valve
Hmax
Smaller
pump
System
Qs
QBP Resulting characteristic
HP
The bypass valve will introduce a maximum limit of head

supplied to the system Hmax , see figure 4.1.3. Even when
the required flow in the system is zero, the pump will never
run against a closed valve. Like it was in the case with
the throttling valve, the required flow QS can be met by a
smaller pump and no bypass valve; the result being a lower
flow and consequently a lower energy consumption.
xx
Pump
QBP
QS
QP
Fig.: 4.1.3: The bypass valve bypasses part of the ow from the pump
and thereby reduces the ow in the system
107
5
Section 4.1
4.1.3 Modifying impeller diameter

Another way of adjusting the performance of a centrifugal
pump is by modifying the impeller diameter in the pump
meaning, reducing the diameter and consequently
reducing the pump performance.
Obviously, reducing the impeller diameter cannot be
done while the pump is operating. Compared to the
throttling and bypass methods, which can be carried out
during operation, modifying the impeller diameter has
to be done in advance before the pump is installed or in
connection with service. The following formulas show the
relation between the impeller diameter and the pump
performance:
Please note that the formulas are an expression of an

ideal pump. In practice, the pump efficiency decreases
when the impeller diameter is reduced. For minor changes
of the impeller diameter Dx > 0.8 . Dn, the efficiency is
only reduced by a few %-points. The degree of efficiency
reduction depends on pump type and duty point (check
specific pump curves for details).
As it appears from the formulas, the flow and the head
change with the same ratio that is the ratio change
of the impeller diameter in second power. The duty
points following the formulas are placed on a straight
line starting in (0,0). The change in power consumption
is following the diameter change in fourth power.
4.1.4 Speed control

The last method of controlling the pump performance
that we will cover in this section is the variable speed
control method. Speed control by means of a frequency
converter is without no doubt the most efficient way of
adjusting pump performance exposed to variable flow
requirements.
108
xx
Hn
Hx
Dn
Dx
Qx
Qn
Fig. 4.1.4: Change in pump performance when the impeller

diameter is reduced
The following equations apply with close approximation to

how the change of speed of centrifugal pumps influences
the performance of the pump:
The affinity laws apply on condition that the system

characteristic remains unchanged for nn and nx and forms
a parabola through (0,0) see section 3.1.1. The power
equation furthermore implies that the pump efficiency is
unchanged at the two speeds.
The formulas in figure 4.1.5 show that the pump flow (Q)
is proportional to the pump speed (n). The head (H) is
proportional to the second power of the speed (n) whereas
the power (P) is proportional to the third power of the
speed. In practice, a reduction of the speed will result in a
slight fall in efficiency. The efficiency at reduced speed (nx)
can be estimated by the following formula, which is valid
for speed reduction down to 50% of the maximum speed:
Finally, if you need to know precisely how much power you

can save by reducing the pump speed, you have to take the
efficiency of the frequency converter and the motor into
account.
Fig. 4.1.5: System characteristics for different affinity equations
109
Section 4.1
4.1.5 Comparison of adjustment methods
Now that we have described the four different ways of

changing the performance of a centrifugal pump, we will
have a look at how they differ from one another.
When we consider the pump and its performance-changing
power QHsulting performance
efficiency
device as one unit,Overall
we can
observe Relative
the resulting
consumption
will havecharacteristic of thisofdevice
the pump
and compare the result by
of 20%
the
reduction
in
flow
system
Relative
power
sulting performance
Overall
efficiency
different systems.
powerby 20%
sulting
performance
Overall
efficiency Relative
consumption
will have
of the pump
ced
Q
Considerably
consumption
by 20%
will
have
94%
of
the
pump
reduction
in flow
system efficiency Relative power
sulting performance
Overall
Throttle
control
reduced
reduction
in
flow
system
consumption by 20%
will have
of the pump
implies a valve connected
series
ced Q The throttling method
Considerably
94%
reduction
ininflow
system
ced Q with a pump, see Considerably
94%
reduced
figure 4.1.6a. This connection acts as
reduced
ced Q a new pump at unchanged
Considerably
94%reduced
maximum head but
reduced
flow performance. The pump curve Hn, the valve curve and
the curve covering the complete system - Hx, see figure
e
4.1.6b.
110%
Considerably
ced
H and changed
e
reduced
e
Bypass control
110%
Considerably
ced
H and changed
e
When a valve is connected
across the pump, see figure
4.1.7a,
110%
Considerably
ced H and changed
reduced
this connection actsreduced
as a new pump at reduced maximum
110%
Considerably
ced H and changed
head and a QH-curve
with a changed characteristic. The
reduced
curve will tend to be more linear than quadratic, see figure
e
4.1.7b
ed
e Q and H
Slightly reduced
67%
The impeller reducing

method
does not imply67%
any extra
Slightly
reduced
ed
e Q and H
67%
FigureSlightly
4.1.8 shows
the reduced QH-curve
(Hx)
reduced
ed Q andcomponents.
H
and
the
original
curve
characteristics
(H
).
67%
Slightly reduced
ed Q and H
n
Speed control
The speed control method (figure 1.4.9) results in a

new QH-curve at reduced head and flow. The characteristics
65%
ed Q and H
Slightly reduced
of the curves remain the same. However, when speed
become
more flat, as the
65%head is
ed Q andisHreduced the curves
Slightly
reduced
65%
ed Q andreduced
H
to a higherSlightly
degree reduced
than the flow.
65%
ed Q and H
Slightly reduced
Compared to the other methods the speed control
method also makes it possible to extend the performance
range of the pump above the nominal QH-curve, simply
by increasing the speed above nominal speed level of
the pump, see the Hy-curve in figure 4.1.9. If this oversynchronous operation is used, the size of the motor has
to be take into account.
110
b
Throttle valve
Throttle valve
Throttle valve
Throttle valve
Hn
Hx
Valve
Fig. 4.1.6: Throttle valve connected in series with a pump
Bypass valve
Hn
Hn
Hx
Hx
Valve
Valve
Hn
Hx
Valve
Hn
Hx
Valve
Hx
Hx
Valve
Valve
Hn
Hx
Valve
Hn
Hx
Hn
Hn
Hx
Hx
Hn
Hx
Hn
Hx
Hy
Hn
Hn
Hx
Hx
Hy
Hy
Hn
Hx
Hy
Bypass valve
Bypass valve
Bypass valve
Hn
Fig. 4.1.7: Bypass valve connected across the H
pump
n
D
D
D
D
Speed controller
Fig. 4.1.8: Impeller diameter adjustment
Speed controller
Speed controller
Speed controller
Fig. 4.1.9: Speed controller connected to a pump
4.1.6 Overall efficiency of the pump system

Both the throttling and the bypass method introduce some
hydraulic power losses in the valves (Ploss = k Q H). Therefore,
the resulting efficiency of the pumping system is reduced.
Reducing the impeller size in the range of Dx/Dn>0.8
does not have a significant impact on the pump
efficiency. Therefore, this method does not have a
negative influence on the overall efficiency of the system.
The efficiency of speed-controlled pumps is only affected
to a limited extent, as long as the speed reduction does
not drop below 50% of the nominal speed. Later on, we
will discover that the efficiency has only reduced a few %points, and that it does not have an impact on the overall
running economy of speed-controlled solutions.
4.1.7 Example: Relative power consumption

when the flow is reduced by 20%
In an given installation the flow has to be reduced from
Q = 60 m3/h to 50 m3/h. In the original starting point
(Q = 60 m3/h and H = 70 m), the power input to the
pump is set relatively to 100%. Depending on the method
of performance adjustment, the power consumption
reduction will vary. Now, let us have a look at how
the power consumption affects each of the performance
adjustment methods.
111
Section 4.1
Throttle control
The power consumption is reduced to about 94% when
the flow drops. The throttling results in an increased head,
see figure 4.1.10. The maximum power consumption is for
some pumps at a lower flow than the maximum flow. If
this is the case, the power consumption increases because
of the throttle.
H
H [m]
[m]
H
[m]
H [m]
= Modified duty point

= Original duty point
76
76
76
70
76
70
70
55
70
55
55
55
Q
Q
Q
Q
P
P222
P
100%
P2
100%
100%
94%
100%
94%
94%
94%
Bypass control
To reduce the flow in the system, the valve has to reduce
the head of the pump to 55 m. This can only be done by
increasing the flow in the pump. As it appears from figure
4.1.11, the flow is consequently increased to 81 m3/h, which
results in an increased power consumption of up to 10%
above the original consumption. The degree of increase
depends on the pump type and the duty point. Therefore,
in some cases, the increase in P2 is equal to zero and in a
few rare cases P2 might even decrease a little.
50
50
50
3
Q
Q [m
[m33/h]
/h]
Q
[m
/h]
Q [m3/h]
60
60
60
50
60
Fig. 4.1.10: Relative power consumption
- throttle control
H
H [m]
[m]
H
[m]
H [m]

70
70
70
70
55
55
55
55
P
P
P222
P
100%
100%2
100%
100%
Q
Q
Q
Q
110%
110%
110%
110%

When the impeller diameter is reduced, both the flow and
the head of the pump drop. By a flow reduction of 20%,
the power consumption is reduced to around 67% of its
original consumption, see figure 4.1.12.
50
50
50
50
When it comes to obtaining the best possible efficiency, the

impeller diameter adjustment method or the speed control
method of the pump are the best suited for reducing the
flow in the installation. When the pump has to operate
in a fixed, modified duty point, the impeller diameter
adjustment method is the best solution. However, when
we deal with an installation, where the flow demand
varies, the speed-controlled pump is the best solution.
81
81
81
81
Q [m
[m3/h]
/h]
Q
Q
[m33/h]
Q [m3/h]
Fig. 4.1.11: Relative power consumption - bypass control

H [m]
[m]
H
H [m]
H [m]

70
70
70
70
55
55
55
55
Speed control
When the speed of the pump is controlled, both the flow
and the head are reduced, see figure 4.1.13. Consequently,
the power consumption has reduced to around 65% of the
original consumption.
60
60
60
60
Q
Q
Q
Q
P
P222
P
P
100%
100%2
100%
100%
67%
67%
67%
67%
50
50
50
50
60
60
60
60
Q [m
[m3/h]
Q
Q [m33/h]
/h]
Q [m3/h]
Fig. 4.1.12: Relative power consumption - modifying impeller diameter

H [m]
[m]
H
H [m]
H [m]

70
70
70
70
55
55
55
55
Q
Q
Q
Q
Q
Q
Q
Q
P
P
P222
P2
100%
100%
100%
100%
65%
65%
65%
65%
50
50
50
50
60
60
60
60
3
Q
Q [m
[m33/h]
/h]
Q
[m
/h]
Q [m3/h]
Fig. 4.1.13: Relative power consumption - speed control
112
Summary
Figure 4.1.14 gives an overview of the different adjustment
methods that we have presented in the previous section.
Each method has its pros and cons which have to be taken
into account when choosing an adjustment method for a
system.
Continuous
adjustment
possible?
Method
Throttle control
Yes
The resulting performance

curve will have
Reduced Q
Overall efficiency
of the pump
system
Considerably
reduced
Relative power
consumption by 20%
reduction in flow
94%
Throttle valve
Throttle valve
Hn
Hx
Valve
Yes
Bypass control
Reduced H and changed

curve
Considerably
reduced
110%
Slightly reduced
67%
Bypass valve
Bypass valve
Hn
Hx
Valve
Modifying impeller
diameter
No
Reduced Q and H
Hn
Hx
Speed control
Yes
Reduced Q and H
Slightly reduced
65%
Speed controller
Speed controller
Hn
Hx
Hy
Fig. 4.1.14: Characteristics of adjustment methods.
113
Section 4.2
Speed-controlled pump solutions
As discussed in the previous section, speed control of pumps

is an efficient way of adjusting pump performance to the
system. In this section we will discuss the possibilities of
combining speed-controlled pumps with PI-controllers
and sensors measuring system parameters, such as
pressure, differential pressure and temperature. On the
following pages, the different options will be presented
by examples.
4.2.1 Constant pressure control

A pump has to supply tap water from a break tank to
different taps in a building.
The demand for tap water is varying, so therefore the
system characteristic varies according to the required
flow. Due to comfort and energy savings a constant supply
pressure is recommended.
Setpoint pset
As it appears from figure 4.2.1, the solution is a speedcontrolled pump with a PI-controller. The PI-controller
compares the needed pressure pset with the actual supply
pressure p1, measured by a pressure transmitter PT.
If the actual pressure is higher than the setpoint, the
PI-controller reduces the speed and consequently the
performance of the pump, until p1 = pset. Figure 4.2.1 shows
what happens when the flow is reduced from Qmax to Q1 .
Setpoint pset
Actual value p1
PIThe controller sees to it that the speed of the
pump
is
controller
reduced from nn to nx in order to ensure that the required Pressure
discharge pressure is p1 = pset. Break
The pump installation transmitter
Speed
ensures that the supply pressure tank
is constant controller
in the flow
range of 0 - Qmax. The supply pressure is independent
PT
on the level (h) in the breakh tank. If h changes, the PI1
controller adjusts the speed of the pump so Q
that
p1 alwaysp1
H1
corresponds to the setpoint.
PIcontroller
Break
tank
Actual value p1
Pressure
transmitter
Speed
controller
PT
pset
Taps
p1
Q1
H1
H
nn
nx
pset
Taps
Q1
Qmax
Fig. 4.2.1: Water supply system with speed-controlled pump delivering

constant pressure to the system
114
4.2.2 Constant temperature control

Performance adjustment by means of speed control is
suitable for a number of industrial applications. Figure 4.2.2
shows a system with an injection moulding machine which
has to be water-cooled to ensure high quality production.
The machine is cooled with water at 15oC from a cooling
plant. To ensure that the moulding machine runs properly
and is cooled sufficiently, the return pipe temperature has
to be kept at a constant level; tr = 20oC. The solution is a
speed-controlled pump, controlled by a PI-controller. The
PI-controller compares the needed temperature tset with
the actual return pipe temperature tr, which is measured
by a temperature transmitter TT. This system has a fixed
system characteristic and therefore the duty point of the
pump is located on the curve between Qmin and Qmax. The
higher the heat loss in the machine, the higher the flow
of cooling water needed to ensure that the return pipe
temperature is kept at a constant level of 20 oC.
Fig. 4.2.2: System with injection moulding machine and temperaturecontrolled circulator pump ensuring a constant return pipe temperature
4.2.3 Constant differential pressure in a

circulating system
Circulating systems (closed systems), see chapter 3, are
well-suited for speed-controlled pump solutions. It is an
advantage that circulating systems with variable system
characteristic are fitted with a differential pressurecontrolled circulator pump, see figure 4.2.3.
The figure shows a heating system consisting of a heat
exchanger where the circulated water is heated up and
delivered to three consumers, e.g. radiators, by a speedcontrolled pump. A control valve is connected in series at
each consumer to control the flow according to the heat
requirement.
The pump is controlled according to a constant differential
pressure, measured across the pump. This means that
the pump system offers constant differential pressure in
the Q-range of 0 Qmax, depicted as the horizontal line in
figure 4.2.3.
Fig. 4.2.3: Heating system with speed-controlled circulator pump delivering

constant differential pressure to the system
115
Section 4.2
Speed-controlled pump solutions
4.2.4 Flow-compensated differential

pressure control
Setpoint Hset
The main function of the pumping system in figure 4.2.4

is to maintain a constant differential pressure across the
control valves at the consumers, e.g. radiators. In order to
do so, the pump has to be able to overcome friction losses
in pipes, heat exchangers, fittings, etc.
Such a pumping system can be designed in two different

ways:
Actual value H1
Speed
controller
Q1
Hset
DPT1
As we discussed in chapter 3, the pressure loss in a system

Setpoint Hset
Actual value H1
PIis proportional to the flow in secondcontroller
power. The best way
to control a circulator pump in a system like the one shown
in the figure on your right, is to allow the pump to deliver a
Speed
pressure, which increases when the controller
flow
increases.
When the demand of flow is low,Qthe
pressure losses in the
1
pipes, heat exchangers, fittings, etc. are low as well, and
the pump only supplies a pressure equivalent
to what the
DPT1
control valve requires, Hset-Hf. When the demand of flow DPT
2
increases, the pressure losses increase in second power
and therefore the pump has to increase the delivered
pressure; depicted as the blue curve in figure 4.2.4.
PIcontroller
Hf
DPT2
nn
nx
Hset
Hf
H1
Q1
Qmax
Fig. 4.2.4: Heating system with speed-controlled circulator pump

delivering flow-compensated differential pressure to the system
The differential pressure transmitter is placed across the

pump and the system is running with flow-compensated
differential pressure control DPT1, see figure 4.2.4.
The differential pressure transmitter is placed close to

the consumers and the system is running with
differential pressure control DPT2 in fig. 4.2.4.
The advantage of the first solution is that the pump, the
PI-controller, the speed control and the transmitter are
placed close to one another, making the installation easy.
This installation makes it possible to get the entire system
as one single unit, see section 4.4. In order to get the
system up and running, pump curve data have to be stored
in the controller. These data are used to calculate the flow
and likewise to calculate how much the setpoint Hset has
116
to be reduced at a given flow to ensure that the pump

performance meets the required blue curve in figure 4.2.4.
The second solution with the transmitter placed in the
installation requires more installation costs because the
transmitter has to be installed at the installation site and
the necessary cabling has to be carried out as well. The
performance of this system is more or less similar to the
first system. The transmitter measures the differential
pressure at the consumer and compensates automatically
for the increase in required pressure in order to overcome
the increase in pressure losses in the supply pipes, etc.
Section 4.3
Advantages of speed control
A large number of pump applications do not require full

pump performance 24 hours a day. Therefore, it is an
advantage to be able to adjust the pumps performance
in the system automatically. As we saw in section 4.1,
the best possible way of adapting the performance of
a centrifugal pump is by means of speed control of the
pump. Speed control of pumps is normally made by a
frequency converter unit.
On the following pages we will have a look at speedcontrolled pumps in closed and open systems. But before
we dig any further into the world of speed control, we will
present the advantages that speed control provides and
the benefits that speed-controlled pumps with frequency
converter offer.
Reduced energy consumption

Speed-controlled pumps only use the amount of energy
needed to solve a specific pump job. Compared to other
control methods, frequency-controlled speed control
offers the highest efficiency and thus the most efficient
utilization of the energy, see section 4.1.
Low life cycle costs

As we will see in chapter 5, the energy consumption of a
pump is a very important factor considering a pumps life
cycle costs. Therefore, it is important to keep the operating
costs of a pumping system at the lowest possible level.
Efficient operation leads to lower energy consumption and
thus to lower operating costs. Compared to fixed speed
pumps, it is possible to reduce the energy consumption by
up to 50% with a speed-controlled pump.
Protection of the environment

Energy efficient pumps polute less and thus do not harm
the environment.
Increased comfort
Speed control in different pumping systems provides
increased comfort: In water supply systems, automatic
pressure control and soft-start of pumps reduce water
hammer and noise generated by too high pressure in the
system. In circulating systems, speed-controlled pumps
ensure that the differential pressure is kept at a level so
that noise in the system is minimised.
Reduced system costs

Speed-controlled pumps can reduce the need for
commissioning and control valves in the system.
Therefore, the total system costs can be reduced.
Kapitel 1
117
5
Section 4.4
Advantages of pumps with integrated
frequency converter
In many applications, pumps with integrated frequency

converter is the optimum solution. The reason is that these
pumps combine the benefits of a speed-controlled pump
solution with the benefits gained from combining a pump,
a frequency converter, a PI-controller and sometimes
also a sensor/pressure transmitter in one single unit
see figure 4.4.1.
A pump with integrated frequency converter is not just
a pump, but a system which is able to solve application
problems or save energy in a variety of pump installations.
As regards replacement, pumps with integrated frequency
converters are ideal as they can be installed instead of
xed speed pumps at no extra installation cost. All that
is required is a power supply connection and a fitting of
the pump with integrated frequency converter in the pipe
system, and then the pump is ready for operation. All
the installer has to do is to adjust the required setpoint
(pressure) after which the system is operational.
Setpoint
PIcontroller
Frequency
converter
What follows is a brief description of the advantages that

pumps with integrated frequency converter have to offer.
PT
Easy to install
Pumps with integrated frequency converter are just as
easy to install as fixed speed pumps. All you have to do is
to connect the motor to the electrical power supply and
the pump is in operation. The manufacturer has made all
internal connections and adjustments.
Optimal energy savings

Because the pump, the motor and the frequency converter
are designed for compatibility, operation of the pump
system reduces power consumption.
One supplier
One supplier can provide pump, frequency converter
and sensor which naturally facilitate the dimensioning,
selection, ordering procedures, as well as maintenance
and service procedures.
118
Fig. 4.4.1: Pump unit with integrated

frequency converter and pressure transmitter
Wide performance range

Pumps with integrated frequency converter have a
very broad performance range, which enables them to
perform efficiently under widely varied conditions and to
meet a wide range of requirements. Thus, fewer pumps
can replace many fixed speed pump types with narrow
performance capabilities.
H
[m] 100%
4.4.1. Performance curves of speedcontrolled pumps

Now, let us have a closer look at how you can read a
speed-controlled pumps performance curve.
Figure 4.4.2 shows an example of the performance curves
of a speed-controlled pump. The rst curve shows the QHcurve and the second curve shows the corresponding power
consumption curve.
As you can tell, the performance curves are given for every
10% decrease in speed from 100% down to 50%. Likewise,
the minimum curve represented by 25% of the maximum
speed is also shown. As we have indicated in the diagram,
you can point out a specific duty point QH and nd out at
which speed the duty point can be reached and what the
power consumption P1 is.
4.4.2 Speed-controlled pumps in different

systems
Speed-controlled pumps are used in a wide range of systems.
The change in pump performance and consequently the
potential energy saving depend on the system in question.
As we discussed in chapter 3, the characteristic of a system
is an indication of the required head a pump has to deliver,
in order to transport a certain quantity of liquid through
the system. Figure 4.4.3 shows the performance curve and
the system characteristic of a closed and an open system.
70
90%
60 86%
50 80%
40
70%
30 60%
20
10
50%
25%
10
15
20
25
35
30
Q [m3/h]
P
[kW]
6
4
2
0
Q [m3/h]
Fig 4.4.2: Performance curve for a speed-controlled pump
Pump curve
Pump curve
System
characteristic HO HO
Closed system
System
characteristic
Open system
Fig 4.4.3: System characteristic point of a closed and an open

system
119
Section 4.4
Advantages of pumps with integrated frequency converter
Speed-controlled pumps in closed systems

2
Q = 15 m /h
In closed systems, like heating and air-conditioning systems,

the pump has only to overcome the friction losses in the pipes,
valves, heat exchangers, etc. In this section, we will present
an example with a speed-controlled pump in a closed
system. The total friction loss by a full flow of 15 m3/h is 16 m,
see figure 4.4.4.
The system characteristic starts in the point (0,0), the red
line in figure 4.4.5. The control valves in the system always
need a certain operating pressure, so therefore the pump
cannot work according to the system characteristic. That is
why some speed-controlled pumps offer the proportional
pressure control function, which ensures that the pump
will operate according to the orange line shown in the
figure. As you can tell from the figure 4.4.5, the minimum
performance is around 57% of the full speed. In a circulating
system operation at the minimum curve (25% of the full
speed) can be relevant in some situations, for example
when we deal with night-time duty in heating systems.
Boiler
or like
Consumers
Fig. 4.4.4: Closed system
H
[m] 100%
24
99%
90%
20
80%
16
70%
12
60%
8
50%
25%
0
10
12
14
16
Q [m3/h]
P1
[kW]
1.2
0.8
0.4
0
Fig. 4.4.5: A speed-controlled pump in a closed system
120
Q [m3/h]
Speed-controlled pumps in open systems

The system characteristic as well as the operating range of
the pump depend on the type of system in question.
Figure 4.4.6 shows a pump in a pressure boosting / water
supply system. The pump has to supply Q = 6.5 m3/h to the
tap, which is placed h = 20 m above the pump. The inlet
pressure to the pump ps is 1 bar, the pressure at the tap pt
has to be 2 bar and the total friction loss in the system by
full flow pf is 1.3 bar.
Fig. 4.4.6: Pump in a

water supply system
Figure 4.4.7 shows the QH-curve of a pump, which is

able to meet the requirements described before. You can
calculate the required head at zero flow (Ho) by using the
equation on your right.
Q = 6.5 m3/h
pt = 2 bar
h = 20 m
pf = 1.3 bar
ps = 1 bar
pt - Pressure at tapping point

ps - Suction pressure
pf
pf - Friction loss
If you need to calculate the maximum head at a flow (Q) of

6.5 m3/h, this is the equation to use:
Hmax = Ho +
.g
Q - Flow rate
h
pf
1.3 . 10
= 30.2 +
= 43.5 m
.g
998 . 9.81
5
Hmax = Ho +
5
. 10
To cover this
from
zero
flow
to maximum flow
pt application
(2-1)
- ps
H
=
h
+
=
20
+
=
30.2
m speed
3
o
Q = 6.5 m /h
a relative
narrow
.the
g pump operates
998 .in9.81
band, that is from about 65% of the full speed and up to
99% of the full speed. In systems with less friction loss
the variation in speed will be even smaller. If no friction
loss, the minimum speed in the above case is about 79%
speed.
As you can tell from the previous two examples, the

possible variation in speed and consequently in power
consumption is highest in closed systems. Therefore, the
closed systems account for the highest energy saving
potential.
= 30.2 +
1.3 . 105
= 43.5 m
998 . 9.81
- Static lift
(2-1) . 105
p -p
Ho = h + t. s = 20 +
= 30.2 m
g
998 . 9.81
H
[m] 100%
60
50
40
HO
20
10
0
P1
[kW]
90%
80%
70%
60%
50%
25%
8 Q [m3/h]
1.2
0.8
0.4
0
Q [m3/h]
Fig. 4.4.7: A speed-controlled pump in an open system
121
Section 4.5
Frequency converter
As mentioned earlier, speed control of pumps involves a

frequency converter. Therefore, it will be relevant to have
a closer look at a frequency converter, how it operates and
finally to discuss related precautions by using this device.
4.5.1 Basic function and characteristics

It is a well-known fact that the speed of an asynchronous
motor depends primarily on the pole number of the motor
and the frequency of the voltage supplied. The amplitude
of the voltage supplied and the load on the motor shaft
also influence the motor speed, however, not to the same
degree. Consequently, changing the frequency of the
supply voltage is an ideal method for asynchronous motor
speed control. In order to ensure a correct motor magnetisation
it is also necessary to change the amplitude of the voltage.
f2
f1 > f2
f1
4.5.2. Components of the frequency

converter
In principle, all frequency converters consist of the same
functional blocks. The basic function is as mentioned
previously, to convert the mains voltage supply into a new
AC voltage with another frequency and amplitude.
The frequency converter first of all rectifies the incoming
mains voltage and then stores the energy in an intermediate
circuit consisting of a capacitor. The DC voltage is then
converted into a new AC voltage with another frequency
and amplitude.
Because of the intermediate circuit in the frequency
converter the frequency of the mains voltage has no direct
influence on the output frequency and thus to the motor
speed. It does not matter if the frequency is 50Hz or 60Hz
as the rectifier can handle both situations. Additionally, the
incoming frequency will not influence the output frequency,
as this is defined by the voltage/frequency pattern, which
is defined in the inverter. Keeping the above-mentioned
facts in mind, using a frequency converter in connection
with asynchronous motors provides the following benefits:
The system can be used in both 50 and 60 cycle

n
Fig. 4.5.1: Displacement of motor torque characteristic
A frequency/voltage control results in a displacement of the

torque characteristic whereby the speed is changed. Figure
4.5.1 shows the motor torque characteristic (T) as a function
of the speed (n) at two different frequencies/voltages. In
the same diagram is also drawn the load characteristic
of the pump. As it appears from the figure, the speed is
changed by changing frequency/voltage of the motor.
The frequency converter changes frequency and voltage,
so therefore we can conclude that the basic task of a
frequency converter is to change the fixed supply voltage/
frequency, e.g. 3x400 V/ 50Hz, into a variable voltage/
frequency.
areas without any modifications
The output frequency of the frequency converter is

independent on the incoming frequency
The frequency converter can supply output frequencies

higher than mains supply frequency makes
oversynchronous operation possible.
As you can tell from figure 4.5.2, the frequency converter
consists of three other components as well: An EMC filter,
a control circuit and an inverter.
Mains supply AC
EMC
lter
Rectier
Intermediate
circuit DC
Inverter
Control circuit
Fig. 4.5.2: Functional blocks of the frequency converter
122
The EMC filter

This block is not part of the primary function of the
frequency converter and therefore, in principle, could be left
out of the frequency converter. However, in order to meet
the requirements of the EMC directive of the European
Union or other local requirements, the filter is necessary.
The EMC filter ensures that the frequency converter does
not send unacceptably high noise signal back to the mains
thus disturbing other electronic equipment connected to
the mains. At the same time the filter ensures that noise
signals in the mains generated by other equipment do not
enter the electronic devices of the frequency converter
causing damage or disturbances.
The control circuit

The control circuit block has two functions: It controls the
frequency converter and at the same time it takes care of
the entire communication between the product and the
surroundings.
Umotor
Mean value of voltage
The inverter
The output voltage from a frequency converter is

not sinusoidal like the normal mains voltage is. The
voltage supplied to the motor consists of a number of
square-wave pulses, see figure 4.5.3. The mean value of
these pulses forms a sinusoidal voltage of the desired
frequency and amplitude. The switching frequency can
be from a few kHz up to 20 kHz, depending on the
brand. To avoid noise generation in the motor windings, a
frequency converter with a switching frequency
above the range of audibility (~16 kHz) is preferable.
This principle of inverter operation is called PWM (Pulse
Width Modulation) control and it is the control principle
which is used most often in frequency converters today.
The motor current itself is almost sinusoidal. This is shown
in figure 4.5.4 (a) indicating motor current (top) and motor
voltage. In figure 4.5.4 (b) a section of the motor voltage
is shown. This indicates how the pulse/pause ratio of the
voltage changes.
0
t
T = 1/fm
Fig 4.5.3: AC voltage with variable frequency (fm) and
variable voltage (Umotor)
0
0
* Detail
Fig 4.5.4: a) Motor current (top) and motor voltage at PWM (Pulse Width
Modulation) control. b) Section of motor voltage
123
Section 4.5
Frequency converter
4.5.3 Special conditions regarding

frequency converters
a
By installing and using frequency converters or pumps

with integrated frequency converters, there are some
conditions, which the installer and user have to be aware
of. A frequency converter will behave differently at the
mains supply side than a standard asynchronous motor.
This is described in detail below.
Non-sinusoidal power input, three-phase supplied

frequency converters
A frequency converter designed as the one described above
will not receive sinusoidal current from the mains. Among
other things this influences the dimensioning of mains
supply cable, mains switch, etc. Figure 4.5.5 shows how
mains current and voltage appear for a:
a) three-phase, two-pole standard asynchronous motor
b) three-phase, two-pole standard asynchronous motor
with frequency converter.
In both cases the motor supplies 3 kW to the shaft.
A comparison of the current in the two cases shows the

following differences, see gure 4.5.6:
The current for the system with frequency converter

is not sinusoidal
The peak current is much higher (approx. 52%

higher) for the frequency converter solution
This is due to the design of the frequency converter
connecting the mains to a rectifier followed by a capacitor.
The charging of the capacitor happens during short time
periods in which the rectified voltage is higher than the
voltage in the capacitor at that moment.
As mentioned above, the non-sinusoidal current results in
other conditions at the mains supply side of the motor. For a
standard motor without a frequency converter the relation
between voltage (U), current (I) and power (P) is shown
in the box on your right hand side. The same formula
cannot be used for the calculation of the power input in
connection with motors with frequency converters.
124
Fig 4.5.5 a): Three-phase, two-pole Fig 4.5.5 b): Three-phase, two-pole
standard asynchronous motor
standard asynchronous motor with
frequency converter
Standard motor
Mains voltage
400 V
Motor with frequency

converter
400 V
Mains current RMS
6.4 A
6.36 A
Mains current, peak
9.1 A
13.8 A
3.68 kW
3.69 kW
cos = 0.83
PF = 0.86
Power input, P1
cos ,
power factor (PF)
Fig. 4.5.6: Comparison of current of a standard motor and a frequency

converter
In fact, in this case, there is no safeway of calculating

the power input based on simple current and voltage
measurements, as these are not sinusoidal. Instead, the
power must be calculated by means of instruments and
on the basis of instantaneous measurements of current
and voltage.
If the power (P) is known as well as the RMS value of
current and voltage, the so-called power factor (PF) can be
calculated by the formula on your right hand side.
Unlike what is the case when current and voltage are
sinusoidal, the power factor has no direct connection
with the way in which current and voltage are displaced
in time.
When measuring the input current in connection with
installation and service of a system with frequency
converter it is necessary to use an instrument that is capable
of measuring non-sinusoidal currents. In general, current
measuring instruments for frequency converters must be
of a type measuring True RMS.
Frequency converters and earth-leakage circuit

breakers (ELCB)
Earth-leakage circuit breakers are used increasingly as
extra protection in electrical installations. If a frequency
converter is to be connected to such an installation it
must be ensured that the ELCB installed is of a type
which will surely brake - also if failure occurs on the
DC side of the frequency converter. In order to be sure
that the ELCB always will brake in case of earth-leakage
current the ELCBs to be used in connection with frequency
converter must be labelled with the signs shown in
figures 4.5.7 and 4.5.8
Fig 4.5.7: Labelling of the ELCB for single-phase frequency converters
Fig 4.5.8: Labelling of the ELCB for three-phase frequency converters
Both types of earth-leakage circuit breaker are available in

the market today.
125
Chapter 5. Life cycle costs calculation
Section 5.1: Life cycle costs equation

5.1.1 Initial costs, purchase price (Cic)
5.1.2 Installation and commissioning costs (Cin)
5.1.3 Energy costs (Ce)
5.1.4 Operating costs (Co)
5.1.5 Environmental costs (Cenv)
5.1.6 Maintenance and repair costs (Cm)
5.1.7 Downtime costs (loss of production) (Cs)
5.1.8 Decommissioning and disposal costs (Co)
Section 5.2: Life cycle costs calculation an example
Energy costs 90%
Maintenance costs 2-5%

Initial costs 5-8%
Section 5.1
Life cycle costs equation
In this section we will focus on the elements that make up

a pumps life cycle costs (LCC) in order to understand what
LCC is, which factors to consider when we calculate it and
how to calculate it. Finally, we will illustrate the notion life
cycle costs by an example. But before we dig any further
into life cycle costs, we need to understand what the notion
covers.
The life cycle costs of a pump is an expression of how
much it costs to purchase, install, operate, maintain
and dispose of a pump during its lifetime.
Fig. 5.1.1: A guide to life cycle costs analysis for pumping systems
The Hydraulic Institute, Europump and the US Department

of Energy have elaborated a tool called the Pump Life cycle
costs (LCC), see figure 5.1.1. The tool is designed to help
companies minimise the waste and maximise the energy
efficiency in different systems including pumping systems.
Life cycle cost calculations are a decision-making tool that
can be used in connection with design of new installations
or repair of existing installations.
Typical life cycle costs
Initial costs
Maintenance costs
Energy costs
The life cycle costs (LCC) consist of the following elements:

Cic
Cin
Ce
Co
Cemv
Cm
Cs
Cd
Initial costs, purchase price

Installation and commissioning costs
Energy costs
Operating costs (labour costs)
Environmental costs
Maintenance and repair costs
Downtime costs (loss of production)
Decommissioning/disposal costs
In the following paragraphs, each of these elements is

described. As it appears from figure 5.1.2, the energy costs,
initial costs and maintenance costs are the most important.
128
Fig. 5.1.2: Typical life cycle costs of a circulating

system in the industry
LCC is calculated by the following formula:

LCC = Cic + Cin + Ce + Co + Cm + Cs + Cemv + Cd
5.1.1 Initial costs, purchase price (Cic)

The initial costs (Cic) of a pump system includes all
equipment and accessories necessary to operate the
system, e.g pumps, frequency converters, control panels
and transmitters, see figure 5.1.3.
Initial costs
Often, there is a trade-off between the initial costs and

the energy and maintenance costs. Thus, in many cases
expensive components have a longer lifetime or a lower
energy consumption than inexpensive components have.
5.1.2 Installation and commissioning costs

(Cin)
Control
panels
Pump
Frequency
converter
Transmitter
Fig. 5.1.3: Equipment that makes up a pumping system
8000
7000
The installation and commissioning costs include the

following costs:
6000
5000
4000
3000
Installation of the pumps

Foundation
Connection of electrical wiring and instrumentation
Installation, connection and set-up of transmitters,
frequency converters, etc.
Commissioning evaluation at start-up
2000
1000
0
Initial costs
System 1
5200
System 2
7300
Fig. 5.1.4: Initial costs of a constant speed pump system

(system 1) and a controlled pump system (system 2)
As was the case for the initial costs, it is important to check the
trade-off options. In connection with pumps with integrated
frequency converter, many of the components are already
integrated in the product. Therefore, this kind of pump is
often subject to higher initial costs and lower installation and
commissioning costs.
129
Section 5.1
Life cycle costs equation
5.1.3 Energy costs (Ce )

In the majority of cases, energy consumption is the largest
cost in the life cycle costs of a pump system, where pumps
often run more than 2000 hours per year. Actually, around
20% of the worlds electrical energy consumption is used
for pump systems, see figure 5.1.5.
What follows is a list of some of the factors influencing the
energy consumption of a pump system:
Load profile
Pump efficiency (calculation of the duty point), see
figure 5.1.6
Motor efficiency (the motor efficiency at partial load
can vary significantly between high efficiency motors
and normal efficiency motors)
Pump sizing (often margins and round ups tend to
suggest oversized pumps)
Other system components, such as pipes and valves
Use of speed-controlled solutions. By using speedcontrolled pumps in the industry, it is possible to reduce
the energy consumption by up to 50%
5.1.4 Operating costs (Co )

Operating costs cover labour costs related to the operation
of a pumping system. In most cases the labour costs
related to the pumps are modest. Today different types
of surveillance equipment make it possible to connect
the pump system to a computer network, making the
operating costs low.
5.1.5 Environmental costs(Cenv)

The environmental costs cover the disposal of parts and
contamination from the pumped liquid. The environmental
factors contribution to the life cycle costs of a pumping
system in the industry is modest.
130
Other use
80%
Pump systems
20%
Fig. 5.1.5: Energy consumption worldwide
[%]
80
New
Existing
60
40
20
0
10
15
20
25
30
35
40
45
50
55
Q [M3/h]
Fig. 5.1.6: Comparison of the efficiency of a new and an existing

pump
5.1.6 Maintenance and repair costs (Cm)

Maintenance and repair costs cover as the name implies
all costs related to maintenance and repair of the
pump system, for example: Labour costs, spare parts,
transportation and cleaning.
The best way to obtain the optimum working life of a
pump and to prevent breakdowns is to carry out preventive
maintenance.
5.1.7 Downtime costs, loss of production

costs (Cs)
Downtime costs are extremely important when it comes
to pump systems used in production processes. The reason
is simple; it costs a lot of money to stop a production, even
for a shorter period of time. Even though one pump is
enough for the required pump performance, it is always
a good idea to install a standby pump that can take over
and make sure that the production continues even if an
unexpected failure in the pump system should occur, see
gure 5.1.7.
Fig. 5.1.7: Standby pump makes sure that production continues in
case of pump break-down
5.1.8 Decommissioning and disposal

costs (Cd )
Depending on the pump manufacturer, decommissioning
and disposal costs of a pump system are subject to minor
variations. Therefore, this cost is seldom taken into
consideration.
Calculating the life cycle costs

The life cycle costs of a pump system is made up of the
summation of all the above-mentioned components over
the systems lifetime. Typically, the lifetime is said to be in
the range of 10 to 20 years. In the pump business, the life
cycle costs are normally calculated by a more simplified
formula with fewer elements to consider. This formula is
shown on your right.
LCC = Cic + Ce + Cm
131
Section 5.2
Life cycle costs calculation an example
Life cycle costs calculations will help determine which

pump to install in the system. The application has the
following characteristics:
12 operating hours per day
220 operating hours per year
Lifetime of 10 years (calculation period)
Based on these data, it is possible to calculate the life cycle
costs of the two solutions.
Even though the initial costs of a variable speed pump are
twice as high compared to a fixed speed pump, the total
costs of the first-mentioned solution are 25% lower than
the fixed speed pump solution after 10 years.
Besides the lower life cycle costs, the variable speed pump
provides, as discussed in chapter 4, some operational
benefits, e.g. constant pressure in the system.
kW
18.76
11.31
Operating hours per day

Working days per year
hours
days
12
220
12
220
Calculation period
years
10
10
Total energy consumption
kWh
495,264
298,584
Electrical power price

Pump types
Pump price
Maintenance
costs
Average power
consumption
Energy costs
Operating hours per day
Total
costs
Working
days per year
Euro/kWh
Euro
Euro
kW
Euro
hours
Euro
days
Calculation period
years
Total energy
45,000consumption
kWh
495,264
Pump price
Euro/kWh 0.07
Maintenance costs
Euro
3,602
Energy costs
Euro
1,417
Euro
33,284
298,584
40,000
Electrical power price
Pump 35,000
price
30,000
Maintenance costs
Energy25,000
costs
Total costs
20,000
Euro
28,688
0.07
Fixed
3,602
speed
1,417
18.76
33,284
12
38,303
220
0.07
Variable
7,204
speed
1,417
11.31
20,066
12
28,688
220
10
10
0.07
7,204
1,417
20,066
38,303
15,000
10,000
45,000
Pump price
40,000
5,000
Maintenance costs
0
35,000
Energy
costs speed
Variable
30,000
Fig. 5.1.8: Life cycle costs of a fixed and a variable speed pump
25,000
45,000
20,000
40,000
15,000
35,000
10,000
30,000
5,000
25,000
0
20,000
Fixed speed
Variable speed
15,000
Fixed speed
10,000
45,000
Fixed speed
Variable speed
40,000
5,000
0
35,000
30,000 0
Euro
The payback time of the variable speed pump solution is a

bit longer because the pump is more expensive. As you can
tell from figure 5.1.9, the payback time is around 2 years,
and in general industrial applications, this is considered to
be a good investment.
Variable
speed
Average power consumption
Euro
Calculations show that compared to the fixed speed pump,

the variable speed pump consumes 40% less energy.
However, the initial costs (Cic) of the variable speed pump
is twice as high as that of the fixed speed pump.
Fixed
speed
Euro
A fixed speed multistage centrifugal pump

A variable speed multistage centrifugal pump
Pump types
Euro
Let us have a look at an example using the simplified

formula mentioned previously: An industry needs a new
water supply pump and two solutions are taken into
consideration:
Years
10
25,000
20,000
15,000
Fixed speed
10,000
Variable speed
5,000
0
0
Years
Fig. 5.1.9: Payback time for a fixed and a variable speed pump
132
10
Appendix I
Appendix H
Appendix
A) Notations and units
B) Unit conversion tables
C) SI-prexes and Greek alphabet
D) Vapour pressure and density of water at different temperatures
E) Orice
F) Change in static pressure due to change in pipe diameter
G) Nozzles
H) Nomogram for head losses in bends, valves, etc.
I)
Pipe loss nomogram for clean water 20C
J) Periodical system
K) Pump standards
L) Viscosity for different liquids as a function of liquid temperature
Appendix A
Notations and units

The table below provides an overview of the most
commonly used notations and units in connection with
pumps and pump systems.
134
grees
lsius
Appendix B
Unit conversion tables

The conversion tables for pressure and ow show the
most commonly used units in connection with pumping
systems
Pressure
Pascal
(=Newton per
square metre)
bar
kilopond
per square
metre
meter
Water
Column
Technical
atmosphere
Physical
atmosphere
pound per
square inch
Pa, (N/m2)
bar
kp/m2
1
105
9.8067
9806.7
98067
101325
6895
10-5
1
9.807 . 105
0.1020
10197
1
103
104
10333
703.1
mWC
1.020 . 10-4
at (kp/cm2)
1.020 . 10-5
atm
9.869 . 10-4
psi (lb/in2)
1.450 . 10-4
10.20
10-3
1
10
10.33
0.7031
1.020
10-4
0.1
1
1.033
0.07031
0.9869
0.9678 . 10-4
0.09678
0.9678
1
0.06804
14.50
1.422 . 10-3
1.422
14.22
14.70
1
1 Pa
1 bar
1 kp/m2
1 mWC
1 at
1 atm
1 psi
0.09807
0.9807
1.013
0.06895
1 Pa
1 bar
1 kp/m2
1 mWC
1 at
1 atm
1 psi
Flow (volume)
1 m /s
1 m3/h
1 l/s
1 UK GPM
1 US GPM
Cubic metre
per second
Cubic metre
per hour
Litre
per second
Gallon (UK)
per minute
Gallon (US)
per minute
m3/s
m3/h
1 l/s
UK GPM
UK GPM
1
2.778 . 10-4
3600
1
3.6
0.02728
0.02271
1000
0.2778
1
0.07577
0.06309
1320
3.667
13.21
1
0.8327
15651
4.403
15.85
1.201
1
10-3
7.577 . 10-5
6.309 . 10-5
1 m3/s
1 m3/h
1 l/s
1 UK GPM
1 US GPM
Temperature
The formulas listed below show how to convert the most commonly used units for temperature.
From degrees Celsius to Kelvin:
T [K] = 273.15 + t [oC]
From degrees Celsius to degrees Fahrenheit: t [oF] = 32 + 1.8 t [oC]
Degrees
Kelvin
Celsius
Degrees
Kelvin
Fahrenheit
Degrees
Fahrenheit
CK
K
F
T, t
0
00
17.8
273.15
0
373.15
100
-255.35
17.8
273.15
32
373.15
212
255.35
0
32
212
0
1 C =
1K=
1 F =
t
t
t
t
CT, t
CK
K
F
11
11
9/5
9/5
5/9
1
5/9
1
9/5
1
5/9
5/9
1
11 C =
11 K =
9/5
1 F =
135
Appendix C
SI-prexes and Greek alphabet
Factor
109
106
103
102
10
10-1
10-2
10-3
10-6
10-9
1,000,000,000
1,000,000
1,000
100
10
0.1
0.01
0.001
0.000.001
0.000.000.001
Prefix
Symbol
giga
mega
kilo
hekto
deka
deci
centi
milli
mikro
nano
G
M
k
h
da
d
c
m
Greek alphabet
136
Alfa
Beta
Gamma
Delta
Epsilon
Zeta
Eta
Theta
Jota
Kappa
Lambda
My
Ny
Ksi
Omikron
Pi
Rho
Sigma
Tau
Ypsilon
Fi
Khi
Psi
Omega
Appendix D
Vapour pressure and density of water at different temperatures

This table shows the
vapour pressure p [bar]
and the density [kg/m3]
of water at different
temperatures t [oC].
Likewise, the table shows
the corresponding
absolute temperature T [K].
Vapour pressure p and density of water at different temperatures

T[K]
P[bar]
[kg/m3]
t[C]
T[K]
P[bar]
[kg/m3]
0
1
2
3
4
5
6
7
8
9
10
273.15
274.15
275.15
276.15
277.15
278.15
279.15
280.15
281.15
282.15
283.15
0.00611
0.00657
0.00706
0.00758
0.00813
0.00872
0.00935
0.01001
0.01072
0.01147
0.01227
0999.8
0999.9
0999.9
0999.9
1000.0
1000.0
1000.0
999.9
999.9
999.8
999.7
61
62
63
64
65
66
67
68
69
70
334.15
335.15
336.15
337.15
338.15
339.15
340.15
341.15
342.15
343.15
0.2086
0.2184
0.2286
0.2391
0.2501
0.2615
0.2733
0.2856
0.2984
0.3116
982.6
982.1
981.6
981.1
980.5
979.9
979.3
978.8
978.2
977.7
11
12
13
14
15
16
17
18
19
20
284.15
285.15
286.15
287.15
288.15
289.15
290.15
291.15
292.15
293.15
0.01312
0.01401
0.01497
0.01597
0.01704
0.01817
0.01936
0.02062
0.02196
0.02337
999.7
999.6
999.4
999.3
999.2
999.0
998.8
998.7
998.5
998.3
71
72
73
74
75
76
77
78
79
80
344.15
345.15
346.15
347.15
348.15
349.15
350.15
351.15
352.15
353.15
0.3253
0.3396
0.3543
0.3696
0.3855
0.4019
0.4189
0.4365
0.4547
0.4736
977.0
976.5
976.0
975.3
974.8
974.1
973.5
972.9
972.3
971.6
21
22
23
24
25
26
27
28
29
30
294.15
295.15
296.15
297.15
298.15
299.15
300.15
301.15
302.15
303.15
0.02485
0.02642
0.02808
0.02982
0.03166
0.03360
0.03564
0.03778
0.04004
0.04241
998.1
997.8
997.6
997.4
997.1
996.8
996.6
996.3
996.0
995.7
81
82
83
84
85
86
87
88
89
90
354.15
355.15
356.15
357.15
358.15
359.15
360.15
361.15
362.15
363.15
0.4931
0.5133
0.5342
0.5557
0.5780
0.6011
0.6249
0.6495
0.6749
0.7011
971.0
970.4
969.7
969.1
968.4
967.8
967.1
966.5
965.8
965.2
31
32
33
34
35
36
37
38
39
40
304.15
305.15
306.15
307.15
308.15
309.15
310.15
311.15
312.15
313.15
0.04491
0.04753
0.05029
0.05318
0.05622
0.05940
0.06274
0.06624
0.06991
0.07375
995.4
995.1
994.7
994.4
994.0
993.7
993.3
993.0
992.7
992.3
91
92
93
94
95
96
97
98
99
100
364.15
365.15
366.15
367.15
368.15
369.15
370.15
371.15
372.15
373.15
0.7281
0.7561
0.7849
0.8146
0.8453
0.8769
0.9094
0.9430
0.9776
1.0133
964.4
963.8
963.0
962.4
961.6
961.0
960.2
959.6
958.6
958.1
41
42
43
44
45
46
47
48
49
50
314.15
315.15
316.15
317.15
318.15
319.15
320.15
321.15
322.15
323.15
0.07777
0.08198
0.08639
0.09100
0.09582
0.10086
0.10612
0.11162
0.11736
0.12335
991.9
991.5
991.1
990.7
990.2
989.8
989.4
988.9
988.4
988.0
102
104
106
108
110
375.15
377.15
379.15
381.15
383.15
1.0878
1.1668
1.2504
1.3390
1.4327
956.7
955.2
953.7
952.2
950.7
112
114
116
118
120
385.15
387.15
389.15
391.15
393.15
1.5316
1.6362
1.7465
1.8628
1.9854
949.1
947.6
946.0
944.5
942.9
51
52
53
54
55
56
57
58
59
60
324.15
325.15
326.15
327.15
328.15
329.15
330.15
331.15
332.15
333.15
0.12961
0.13613
0.14293
0.15002
0.15741
0.16511
0.17313
0.18147
0.19016
0.19920
987.6
987.1
986.6
986.2
985.7
985.2
984.6
984.2
983.7
983.2
122
124
126
128
130
395.15
397.15
399.15
401.15
403.15
2.1145
2.2504
2.3933
2.5435
2.7013
941.2
939.6
937.9
936.2
934.6
132
134
136
405.15
407.15
409.15
2.8670
3.041
3.223
932.8
931.1
929.4
t[C]
T[K]
P[bar]
[kg/m3]
138
140
145
150
411.15
413.15
418.15
423.15
3.414
3.614
4.155
4.760
927.6
925.8
921.4
916.8
155
160
165
170
175
428.15
433.15
438.15
443.15
448.15
5.433
6.181
7.008
7.920
8.924
912.1
907.3
902.4
897.3
892.1
180
185
190
195
200
453.15
458.15
463.15
468.15
473.15
10.027
11.233
12.551
13.987
15.50
886.9
881.5
876.0
870.4
864.7
205
210
215
220
225
478.15
483.15
488.15
493.15
498.15
17.243
19.077
21.060
23.198
25.501
858.8
852.8
846.7
840.3
833.9
230
235
240
245
250
255
503.15
508.15
513.15
518.15
523.15
528.15
27.976
30.632
33.478
36.523
39.776
43.246
827.3
820.5
813.6
806.5
799.2
791.6
260
265
270
275
280
533.15
538.15
543.15
548.15
553.15
46.943
50.877
55.058
59.496
64.202
783.9
775.9
767.8
759.3
750.5
285
290
295
300
305
310
558.15
563.15
568.15
573.15
578.15
583.15
69.186
74.461
80.037
85.927
92.144
98.700
741.5
732.1
722.3
712.2
701.7
690.6
315
320
325
330
340
588.15
593.15
598.15
603.15
613.15
105.61
112.89
120.56
128.63
146.05
679.1
666.9
654.1
640.4
610.2
350
360
623.15
633.15
165.35
186.75
574.3
527.5
370
374.15
643.15
647.30
210.54
221.2
451.8
315.4
t[C]
137
Appendix E
Orifice
Orifice
As discussed in chapter 3, the duty point of a pump is
adjusted by adding a resistance in connected series with
the pump. In practice, this is normally done by placing an
orifice in the outlet flange of the pump.
The following graph provides the orifice diameter d [mm]

based on the pipe/port dimension DN [mm], the flow Q
[m3/h] and the required head loss H [m].
1000
63 =25 =10 =4
H
H
H
5
3
6
0
0
10 H=4 H=1 H=6. H=2.
=
H
H=
Q [m3/h]
100
10
1
1000
100
Dn=300 Dn=250
Dn=200
Dn=150
Dn=125
Dn=100
Dn=80
Dn=65
Orifice [mm]
Dn=50
Dn=40
Dn=32
10
Example:
The head of a pump, with an outlet flange of 125 mm,
has to be reduced by 25 m at a flow of 150 m3/h.
DN = 125 mm, H = 25 m, Q = 150 m3/h
It is necessary to install an orifice with a diameter of 59 mm.
138
DN
Appendix F
H has to be added to the measured head of the pump:
Change in static pressure due to change

in pipe diameter
H =
As described in chapter 2.2, a change in pipe dimension

results in a change in liquid velocity and consequently, a
change in dynamic and static pressure.
When the head has to be determined (see page 86), the
difference in the two port dimensions requires a correction
of the measured head.
D2 = 150 mm
2.g
8 . Q2
g . 2
[ D1
4
2
_ 1
D14
where :
v1 is the liquid velocity in the inlet port in [m/s]
v2 is the liquid velocity in the outlet port in [m/s]
Q is the flow rate in [m3/s]
g is the acceleration of gravity in [m/s2]
D1 is the diameter of the inlet port in [m]
D2 is the diameter of the outlet port in [m]
The graph shows the H value for typical sets of port
dimensions D1/D2 as a function of the flow Q. In this
case flow Q is measured in [m3/h] and the H is
measured in [m].
Example:
A pump with an inlet port of 250 mm and an outlet
port of 150 mm is pumping 300 m3/h. How much
does the difference in port dimension affect the
measured head?
D1 = 250 mm
22 - 12
Q = 300 m3/h
As it appears from the graph, the difference in

head is H = 1 m.
00
0/ 4
40 00
0 /3
50
0
25
0/
3
50
35
30
0/
00
0/
2
25
50 150
/
15 125
0/
20
0
0/
1
25
80
5/ 150
10 /1
0 00
12
80 125/
0/
10
1
/6 00/
5
65
80
40
/5 8
0 0/
50
65
/
50
/
65
H [m]
D1 /D2 =
32
10
0.10
0.01
10
100
1,000
10,000
Flow [m /h]
3
139
Appendix G
Nozzles
The relation between the nozzle diameter d [mm], the
needed flow Q [m3/h] and the required pressure before
the nozzle p [bar] is found by the nomogram below. We
assume that the nozzle has a quadratic behaviour:
Q1
Q2 =
( )
p1
p2
where n = 0.5. Some nozzles have a lower n value (check

with the supplier).
Pressure
p [bar]
Nozzle diameter
d [mm]
Flow
Q [m3/h]
Example:
A nozzle of 3.5 mm has to supply 1 m3/h. What
is the required pressure in front of the nozzle?
100.00
p [bar]
Q = 1 m3/h, d = 3.5 mm
p = 4.8 bar
10.00
9.0
8.0
7.0
6.0
5.0
4.0
3.5
2.5
2.0
1.5
d=
1.0
1.00
0.10
0.01
140
0.1
Q [m3/h]
10
Appendix H
141
Appendix I
142
Appendix J
Periodical system
1
H
2
He
Hydrogen
Helium
3
Li
4
Be
5
B
6
C
7
N
8
O
9
F
10
Ne
Lithium
Beryllium
Boron
Carbon
Nitrogen
Oxygen
Fluorine
Neon
11
Na
12
Mg
13
Al
14
Si
15
P
16
S
17
Cl
18
Ar
Sodium
Magnesium
Aluminium
Silicon
Phosphorus
Sulphur
Chlorine
Argon
19
K
20
Ca
21
Sc
22
Ti
23
V
24
Cr
25
Mn
26
Fe
27
Co
28
Ni
29
Cu
30
Zn
31
Ga
32
Ge
33
As
34
Se
35
Br
36
Kr
Potassium
Calcium
Scandium
Titanium
Vanadium
Chromium
Manganese
Iron
Cobalt
Nickel
Copper
Zinc
Gallium
Germanium
Arsenic
Selenium
Bromine
Krypton
37
Rb
Rubidium
38
Sr
39
Y
40
Zr
41
Nb
42
Mo
43
Tc
44
Ru
45
Rh
46
Pd
47
Ag
48
Cd
49
In
50
Sn
51
Sb
52
Te
53
I
54
Xe
Strontium
Yttrium
Zirconium
Niobium
Ruthenium
Rhodium
Palladium
Silver
Cadmium
Indium
Tin
Antimony
Tellurium
Iodine
Xenon
55
Cs
56
Ba
57
La
72
Hf
73
Ta
74
W
75
Re
76
Os
77
Ir
78
Pt
79
Au
80
Hg
81
Tl
82
Pb
83
Bi
84
Po
85
At
86
Rn
Caesium
Barium
Lutetium
Hafnium
Tantalum
Tungsten
Rhenium
Osmium
Iridium
Platinum
Gold
Mercury
Thallium
Lead
Bismuth
Polonium
Astatine
Radon
87
Fr
88
Ra
89
Ac
104
Rf
105
Db
106
Sg
107
Bh
108
Hs
109
Mt
110
Ds
111
Rg
113
Uut
114
UUq
Francium
Radium
Actinium
Rutherfordium
Dubnium
Seaborgium
Bohrium
Hassium
58
Ce
59
Pr
60
Nd
61
Pm
62
Sm
63
Eu
64
Gd
65
Tb
66
Dy
67
Ho
68
Er
69
Tm
70
Yb
71
Lu
Promethium
Samarium
Europium
Gadolinium
Terbium
Dysprosium
Holmium
Erbium
Thulium
Ytterbium
Lutetium
Cerium
Molybdenum Technetium
Praseodymium Neodymium
112
Uub
Meitnerium Damstadtium Roentgenium Ununbium
Ununtrium Ununquadium
90
Th
91
Pa
92
U
93
Np
94
Pu
95
Am
96
Cm
97
Bk
98
Cf
99
Es
100
Fm
101
Md
102
No
103
Lr
Thorium
Protactinium
Uranium
Neptunium
Plutonium
Americium
Curium
Berkelium
Californium
Einsteinium
Fernium
Mendelevium
Nobelium
Lawrencium
143
Appendix K
Pump standards
Pump standards:
EN 733
EN 22858
End-suction centrifugal pumps, rating with 10 bar with bearing bracket

End-suction centrifugal pumps (rating 16 bar) - Designation, nominal
duty point and dimensions
Pump related standards:

ISO 3661
EN 12756
EN 1092
ISO 7005
DIN 24296
End-suction centrifugal pumps - Base plate and installation dimensions

Mechanical seals - Principal dimensions, designation and material codes
Flanges and their joints - Circular flanges for pipes, valves, fittings and
accessories, PN-designated
Metallic flanges
Pumps, and pump units for liquids: Spare parts
Specifications etc:
ISO 9905
ISO 5199
ISO 9908
ISO 9906
EN 10204
ISO/FDIS 10816
Technical specifications for centrifugal pumps - Class 1

Rotodynamic pumps - Hydraulic performance tests -Grades 1 and 2
Metallic products - Types of inspection documents
Mechanical vibration - Evaluation of machine vibration by
measurements on non-rotating parts
Motor standards:
EN 60034/IEC 34 Rotating electrical machines
144
Appendix L
Viscosity of typical liquids as a function

of liquid temperature
Viscosity
Kinematic viscosity is measured in centiStoke [cSt]
(1 cSt = 10-6 m2/s). The unit [SSU] Saybolt Universal is also
used in connection with kinematic viscosity. The graph
below shows the relation between kinematic viscosity
in [cSt] and viscosity in [SSU]. The SAE-number is also
indicated in the graph.
The graph shows the viscosity of different liquids at

different temperatures. As it appears from the graph, the
viscosity decreases when the temperature increases.
For kinematic viscosity above 60 cSt, the Saybolt Universal

viscosity is calculated by the following formula:
[SSU] = 4.62 . [cSt]
Kinematic viscosity
centiStokes cSt
cSt
10000
8
6
Sekunder Saybolt
Universal SSU
The densities shown in

the graph are for 20 C
Glycerol
: 1260
2
3
4
5
32
35
40
50
1000
10
8
6
20
Silicone oil
Fuel oil
2
100
8
6
40
50
Olive oil
: 900
100
30
200
300
Cottonseed oil
: 900
Fruit juice
: 1000
100
400
500
SAE 10
Heavy
: 980
200
1000
300
10
8
Mean
: 955
Spindle oil
: 850
400
500
Light
: 930
Silicone oil : 1000

Milk : 1030
Petroleum
: 800
1000
2000
Aniline : 1030
SAE 30
4000
5000
SAE 40
10000
SAE 60
3000
SAE 20
2000
3000
Gas and
diesel oil
: 880
SAE no.
( at 20o C)
SAE 50
SAE 70
4000
5000
20000
10000
40000
50000
20000
100000
30000
Ethyl Alkohol : 770
1.0
8
Silicone oil
Petrol : 750
Water : 1000
Acetone : 790
Ether : 700
Acetic acid
: 1050
Mercury : 13570
0.1
- 10
10
20
30
40
50
60
30000
40000
50000
70
80
90
100C
200000
100000
145
Appendix L
Ethylene glycol
Concentration
wt % =
Temperature
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
10%
15%
20%
25%
30%
35%
40%
45%
50%
55%
-50
1107
-45
1106
173.7
118.6
-40
-35
-30
-15
-10
-5
1081
32.3
1098
101.2
1105
259.7
1089
57.3
1097
68.9
1104
82.7
1089
40.0
1096
48.1
1103
58.8
1080
23.5
1088
28.7
1095
34.4
1102
42.6
1072
14.1
1079
17.4
1086
21.1
1094
25.2
1101
31.5
-25
-20
146
60%
1055
7.2
1063
8.8
1070
10.9
1078
13.2
1085
15.8
1092
18.8
1099
23.6
1046
4.9
1054
5.8
1062
7.0
1069
8.5
1077
10.2
1084
12.1
1091
14.3
1098
18.0
1028
2.9
1036
3.4
1045
4.0
1053
4.7
1060
5.7
1068
6.8
1075
8.1
1082
9.4
1089
11.1
1096
14.0
1018
2.0
1027
2.5
1035
2.9
1043
3.3
1051
3.9
1059
4.7
1066
5.5
1074
6.5
1081
7.5
1088
8.8
1094
11.0
1017
1.7
1026
2.1
1034
2.4
1042
2.8
1050
3.3
1057
3.9
1065
4.5
1072
5.3
1079
6.1
1086
7.1
1092
8.8
10
1016
1.5
1024
1.8
1032
2.1
1041
2.4
1048
2.8
1056
3.2
1063
3.8
1070
4.4
1077
5.0
1084
5.8
1090
7.1
15
1014
1.3
1023
1.6
1031
1.8
1039
2.1
1047
2.4
1054
2.8
1061
3.2
1068
3.7
1075
4.2
1082
4.8
1088
5.9
20
1013
1.1
1021
1.4
1029
1.6
1037
1.8
1045
2.0
1052
2.4
1059
2.7
1066
3.1
1073
3.5
1079
4.0
1086
4.9
25
1011
1.0
1019
1.2
1027
1.4
1035
1.6
1043
1.8
1050
2.1
1057
2.4
1064
2.7
1071
3.0
1077
3.4
1083
4.1
30
1009
0.9
1018
1.1
1026
1.2
1033
1.4
1041
1.6
1048
1.8
1055
2.1
1062
2.3
1068
2.6
1075
3.0
1081
3.5
35
1008
0.8
1016
1.0
1024
1.1
1031
1.2
1039
1.4
1046
1.6
1053
1.8
1059
2.1
1066
2.3
1072
2.6
1078
3.0
40
1006
0.7
1014
0.9
1021
1.0
1029
1.1
1036
1.2
1043
1.4
1050
1.6
1057
1.8
1063
2.0
1069
2.3
1076
2.6
45
1003
0.7
1011
0.8
1019
0.9
1027
1.0
1034
1.1
1041
1.3
1048
1.4
1054
1.6
1060
1.8
1067
2.0
1073
2.2
50
1001
0.6
1009
0.7
1017
0.8
1024
0.9
1031
1.0
1038
1.1
1045
1.3
1051
1.5
1058
1.6
1064
1.8
1070
2.0
55
999
0.6
1007
0.7
1014
0.7
1022
0.8
1029
0.9
1036
1.0
1042
1.2
1048
1.3
1055
1.5
1061
1.6
1066
1.7
60
996
0.5
1004
0.6
1012
0.7
1019
0.7
1026
0.8
1033
0.9
1039
1.1
1045
1.2
1052
1.3
1058
1.4
1063
1.5
65
994
0.5
1001
0.6
1009
0.6
1016
0.7
1023
0.8
1030
0.9
1036
1.0
1042
1.1
1048
1.2
1054
1.3
1060
1.4
1.2
70
991
0.5
998
0.5
1006
0.6
1013
0.6
1020
0.7
1027
0.8
1033
0.9
1039
1.0
1045
1.1
1051
1.2
1056
75
988
0.4
996
0.5
1003
0.5
1010
0.6
1017
0.6
1023
0.7
1030
0.8
1036
0.9
1042
1.0
1047
1.1
1053
1.1
80
985
0.4
992
0.5
1000
0.5
1007
0.5
1014
0.6
1020
0.7
1026
0.8
1032
0.8
1038
0.9
1044
1.0
1049
1.0
0.9
85
982
0.4
989
0.4
997
0.5
1003
0.5
1010
0.5
1017
0.6
1023
0.7
1029
0.8
1034
0.8
1040
0.9
1045
90
979
0.3
986
0.4
993
0.4
1000
0.5
1007
0.5
1013
0.6
1019
0.6
1025
0.7
1031
0.8
1036
0.8
1041
0.8
95
975
0.3
983
0.4
990
0.4
996
0.4
1003
0.5
1009
0.5
1015
0.6
1021
0.6
1027
0.7
1032
0.7
1037
0.8
100
972
0.3
979
0.4
986
0.4
993
0.4
999
0.4
1005
0.5
1011
0.5
1017
0.6
1023
0.6
1028
0.6
1033
0.7
Appendix L
Propylene glycol
Concentration
wt % =
Temperature
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
10%
15%
20%
25%
30%
35%
40%
45%
50%
55%
60%
-50
1077
2433.5
-45
1075
1390.3
-40
-35
1057
1045
817.6
494.4
1069
291.8
1072
157.1
1067
186.7
1071
307.2
87.1
1062
102.5
1066
122.6
1069
196.0
1051
44.9
1056
58.1
1060
68.6
1064
82.6
1067
128.2
1050
31.1
1054
39.8
1058
47.1
1062
56.9
1065
85.9
58.9
1039
11.4
1044
16.2
1048
22.1
1053
27.9
1056
33.2
1060
40.2
1063
1021
3.8
1027
4.8
1032
6.3
1037
8.7
1042
12.0
1047
16.0
1051
20.1
1054
23.9
1058
29.0
1061
41.4
5.1
1036
6.8
1040
9.1
1045
11.9
1049
14.7
1052
17.6
1056
21.4
1059
29.7
-10
-5
1074
22.2
-20
-15
468.8
1063
-30
-25
1070
1013
2.6
1020
3.1
1025
3.9
1031
1012
2.2
1018
2.6
1024
3.2
1029
4.1
1034
5.4
1038
7.0
1043
9.0
1046
11.1
1050
13.2
1053
16.1
1056
21.7
10
1011
1.8
1017
2.2
1022
2.7
1027
3.4
1032
4.3
1036
5.5
1040
6.9
1044
8.5
1048
10.1
1051
12.3
1053
16.2
15
1009
1.6
1015
1.9
1020
2.3
1025
2.8
1030
3.5
1034
4.4
1038
5.5
1042
6.6
1045
7.9
1048
9.6
1051
12.3
20
1008
1.4
1013
1.6
1019
1.9
1023
2.4
1028
2.9
1032
3.6
1036
4.4
1039
5.3
1042
6.3
1045
7.6
1048
9.6
25
1006
1.2
1011
1.4
1017
1.7
1021
2.0
1026
2.5
1030
3.0
1033
3.6
1037
4.3
1040
5.1
1042
6.1
1045
7.5
30
1004
1.1
1009
1.2
1014
1.4
1019
1.7
1023
2.1
1027
2.5
1031
2.9
1034
3.5
1037
4.2
1039
5.0
1042
6.0
35
1002
0.9
1007
1.1
1012
1.3
1017
1.5
1021
1.8
1024
2.1
1028
2.5
1031
2.9
1034
3.5
1036
4.2
1038
4.9
40
1000
0.8
1005
1.0
1010
1.1
1014
1.3
1018
1.5
1022
1.8
1025
2.1
1028
2.5
1031
2.9
1033
3.5
1035
4.0
45
998
0.8
1003
0.9
1007
1.0
1011
1.2
1015
1.4
1019
1.6
1022
1.8
1025
2.1
1027
2.5
1030
3.0
1032
3.4
50
995
0.7
1000
0.8
1005
0.9
1009
1.0
1012
1.2
1016
1.4
1019
1.6
1021
1.8
1024
2.2
1026
2.6
1028
2.9
998
0.7
1002
0.8
1006
0.9
1009
1.1
1012
1.2
1015
1.4
1018
1.6
1020
1.9
1022
2.2
1024
2.4
55
993
0.6
60
990
0.6
995
0.6
999
0.7
1003
0.8
1006
1.0
1009
1.1
1012
1.2
1014
1.4
1017
1.7
1019
1.9
1020
2.1
65
988
0.5
992
0.6
996
0.7
999
0.8
1003
0.9
1006
1.0
1008
1.1
1011
1.3
1013
1.5
1015
1.7
1016
1.9
70
985
0.5
989
0.5
993
0.6
996
0.7
999
0.8
1002
0.9
1005
1.0
1007
1.1
1009
1.3
1011
1.5
1012
1.6
75
982
0.5
986
0.5
989
0.6
993
0.6
996
0.7
998
0.8
1001
0.9
1003
1.0
1005
1.2
1006
1.4
1008
1.5
80
979
0.4
983
0.5
986
0.5
989
0.6
992
0.7
995
0.7
997
0.8
999
10.0
1001
1.1
1002
1.2
1003
1.3
85
976
0.4
979
0.4
982
0.5
985
0.5
988
0.6
991
0.7
993
0.8
995
0.9
996
1.0
998
1.1
999
1.2
90
972
0.4
976
0.4
979
0.4
982
0.5
984
0.6
986
0.6
988
0.7
990
0.8
992
0.9
993
1.0
994
1.1
95
969
0.3
972
0.4
975
0.4
978
0.5
980
0.5
982
0.6
984
0.7
986
0.7
987
0.8
988
0.9
989
1.0
100
965
0.3
968
0.3
971
0.4
974
0.4
976
0.5
978
0.6
980
0.6
981
0.7
983
0.7
984
0.8
984
0.9
147
Appendix L
Sodium hydroxide
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
Concentration
wt % =
Temperature
5%
10%
15%
20%
25%
30%
35%
40%
45%
50%
55%
1060
1117
1174
1230
1285
1334
1384
1435
1483
1530
1559
1058
1115
1172
1227
1283
1332
1381
1429
1480
1528
1556
10
1057
1113
1170
1224
1280
1330
1377
1423
1478
1525
1553
15
1056
1111
1167
1222
1277
1326
1372
1420
1471
1518
1546
20
1054
1.3
1109
1.7
1164
2.5
1219
3.6
1274
6.2
1322
10.1
1367
16.8
1416
25.4
1464
38.2
1511
51.8
25
1052
1.1
1107
1.5
1162
2.1
1217
3.1
1271
5.1
1319
8.3
1364
13.3
1413
19.9
1461
29.0
1508
39.0
30
1050
1.0
1104
1.3
1159
1.8
1214
2.7
1268
4.0
1315
6.5
1360
9.9
1410
14.4
1457
19.9
1504
26.2
35
1048
0.9
1102
1.2
1157
1.6
1211
2.3
1265
3.4
1312
5.5
1357
8.2
1407
11.6
1454
15.9
1501
20.5
40
1046
0.8
1100
2.0
1262
2.8
1309
4.5
8.9
1450
12.0
1497
14.7
1.1
1.4
1154
1208
1353
6.6
1403
45
1044
0.7
1097
1.0
1151
1.3
1205
1.8
1259
2.6
1306
3.9
1347
5.6
1396
7.5
1443
9.9
1490
12.1
50
1042
0.7
1094
0.9
1148
1.2
1202
1.6
1256
2.3
1302
3.3
1340
4.6
1389
6.0
1436
7.8
1483
9.4
55
1039
0.6
1092
0.8
1145
1.0
1199
1.5
1253
2.0
1299
2.9
60
0.7
1143
0.9
1196
1.3
1250
1.8
1295
2.4
25
30
40
45
1036
0.6
1089
65
1033
0.5
1086
0.7
1140
0.9
1193
1.2
1246
1.6
70
1030
0.5
1083
0.6
1137
0.8
1190
1.1
1243
1.5
75
1027
1080
1134
1186
1240
80
1025
1077
1131
1183
1237
1540
cSt
kg/m3
100
1600
55%
50%
1500
50%
45%
40%
45%
35%
40%
10
1400
30%
35%
25%
30%
1300
20%
15%
10%
5%
25%
20%
1200
15%
10%
1100
5%
0
20
1000
0
148
10
20
30
40
50
60
70
80
35
50
55
60
65
70
Appendix L
Calcium chloride
Concentration
wt % =
Temperature
Natrium chloride
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
[kg/m3]
[cSt]
10%
15%
20%
Concentration
wt % =
Temperature
25%
-25
1245
7.7
-15
-20
1244
6.3
-10
-15
-10
1138
3.0
5%
10%
15%
20%
1162
4.0
1120
2.9
1160
3.2
1189
4.3
1242
5.2
-5
1082
2.2
1118
2.4
1158
2.7
1188
3.6
1241
4.4
1043
1.8
1080
1.8
1116
2.0
1155
2.3
-5
1090
2.3
1137
2.6
1187
3.1
1239
3.8
1042
1.5
1079
1.6
1114
1.7
1153
1.9
1088
2.0
1135
2.2
1186
2.6
1237
3.3
10
1041
1.3
1077
1.4
1112
1.5
1151
1.7
1086
1.7
1134
1.9
1184
2.3
1235
2.9
15
1040
1.1
1075
1.2
1110
1.3
1148
1.5
10
1085
1.5
1132
1.7
1182
2.0
1233
2.5
20
1039
1.0
1074
1.1
1108
1.2
1146
1.3
1037
0.9
1072
0.9
1106
1.0
1144
1.2
1036
0.8
1070
0.9
1103
0.9
1141
1.1
15
1083
1.3
1131
1.5
1180
1.8
1230
2.2
25
20
1082
1.1
1129
1.3
1178
1.6
1228
2.0
30
25
1082
1.0
1127
1.2
1176
1.4
1226
1.8
30
1081
0.9
1125
1.0
1173
1.3
1223
1.6
149

Pump Handbook Complete

Uploaded by

Copyright:

Available Formats

Pump Handbook Complete

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pump Handbook Complete

Uploaded by

Copyright:

Available Formats

What is the purpose of the pump handbook?

What is the purpose of the pump handbook?

What topics are covered in Chapter 1?

What topics are covered in Chapter 1?

GRUNDFOS INDUSTRY

Being responsible is our foundation

Poul Due Jensens Vej 7

GRUNDFOS Management A/S

Copyright 2004 GRUNDFOS Management A/S. All rights reserved.

Business Development Manager

Claus Brnholdt Nielsen

Chapter 1 Design of pumps and motors ......................7

Section 1.1 Pump construction ............................................................ 8

Section 1.5 Liquids .......................................................................................53

Chapter 2 Installation and performance

Chapter 3 System hydraulic .................................................... 95

Chapter 5 Life cycle costs calculation

Section 3.1 System characteristics .................................................96

Section 5.1 Life cycle costs equation ............................................ 128

Section 3.2 Pumps connected in series and parallel...................101

Chapter 4 Performance adjustment

Section 5.2 Life cycle costs calculation

Dust ignition proof (DIP)

NEMA, motor standard

Chapter 1. Design of pumps and motors

Section 1.1: Pump construction

The centrifugal pump

Section 1.2: Types of pumps

1.1.1 The centrifugal pump

Fig. 1.1.1: The liquids flow through the pump

Radial flow pump

Mixed flow pump

Axial flow pump

Fig. 1.1.2: Different kinds of centrifugal pumps

If a pressure difference occurs in the system while the

However, we will briefly present the positive displacement

The different demands on the centrifugal pumps

Mixed flow pumps

Axial flow pumps

1.1.2 Pump curves

Normally, pump curves in data booklets only cover the

Fig. 1.1.4: Typical performance curves for a centrifugal

What follows is a brief presentation of the different pump

Head, the QH-curve

The QH-curve shows the head, which the pump is able

Fig. 1.1.6: A typical QH-curve for a centrifugal pump;

Efficiency, the -curve

For water at 20oC and with Q measured in m3/h and H in m,

Fig. 1.1.7: The efciency curve of a typical centrifugal pump

As it appears from the efficiency curve, the efficiency depends

Power consumption, the P2-curve

The relation between the power consumption of the pump

NPSH-curve (Net Positive Suction Head)

Fig. 1.1.8: The power consumption curve of a typical

Fig. 1.1.9: The NPSH-curve of a typical centrifugal pump

1.1.3 Characteristics of the

The number of stages

The position of the pump shaft

Single-suction or double-suction impellers

Construction of the pump casing