Infra Design

CIVIL WORK DESIGN
INFRA-STRUCTURE Design
Consultant:
Perunding RekaCeKap Sdn Bhd
11A-3 (2nd floor), Jalan USJ 21/7
47630 UEP Subang Jaya
Selangor Darul Ehsan
1.0 BASIC SCOPE OF CIVIL WORKS
Road & Drainages
Earthworks
1.0 BASIC SCOPE OF CIVIL WORKS
Water Supply
Sewerage
1.0 OTHER SCOPE OF CIVIL WORKS
Highway & Bridges

Waste Water Treatment
1.0 OTHER SCOPE OF CIVIL WORKS
Irrigation
Water Resources
EARTHWORK
Scope of earthwork involves:
Site clearance
Construction of temporary site access
General earthwork (cut & fill)
Construction of wash trough
Construct of silt trap & earth drain
Construction of slope/retaining system
Erosion and sedimentation control
EARTHWORK scope
Site clearance
Cut/Fill
Temporary Access
Basement Excavation
EARTHWORK - scope
berm drains
retaining system
EARTHWORK scope
Sedimentation control
Check dam
Silt Fence
EARTHWORK Design info

Topographical map / survey plan
Soil investigation rock profile/soil type
Existing services survey
Development layout
SITE VISIT
EARTHWORK Design Considerations

Topographical of the site and surrounding
boundaries
Existing road levels
Existing stream/drainage discharge inverts
Existing sewerage connection inverts
AVOID / minimize ROCK blasting
Platform to suit type of development
Slope whenever possible avoid retaining walls
Silt control (ESCP)
EARTHWORK Design Compliances

To match surrounding levels
To allow future connectivity of road system
To ensure NO siltation on surrounding
neighboring lands
To ensure FOS of slope stability
To ensure soil settlement within limit
To ensure soil movement do not damage
adjacent properties
EARTHWORK - Design
Platform/level design
Volume calculations BALANCE design
Slope/retaining system analysis & design
Erosion and sedimentation control plan
(ESCP)
EARTHWORK Platform Design

To suit existing contour
To suit type of development
To minimize earthwork cut & fill
To avoid retaining system
Design above flood level
To ensure gravity flow of infra services,
such as sewer & storm water
Slope gradient to avoid strengthening
work
Limit maximum road gradient
EARTHWORK Volume Calculation
Methods to calculate earthwork cut & fill:

Trapezoid Volume Method
Cut sections
Computer software
EARTHWORK Slope Design

General design requirements:
Earth cut slope is 1V: 1.5H (maximum 6m)
Earth fill slope is 1V: 2H (maximum 4.5m)
Berm width 1.5~2m
Minimum factor of safety for slope is 1.25
(or to local authorities requirements)
Analysis using software
EARTHWORK Retaining system

Type of retaining system:
Gabion Wall
Crib Wall
RC Wall
RE Wall
EARTHWORK Retaining wall Design

General design requirements:
Overturning
Sliding
Soil pressure
Strength (for RC wall)
Analysis using software
EARTHWORK ESC Design

Design Comply to MSMA guidelines
The design criteria adopted for sediment are as follow:
Basin Type
: Dry
Soil Type
: Fine-grained loam, clay: more than 33%
< 0.02mm
Design Storm
: 3 months ARI
Location of Fitted Coefficient for IDF Curves : Selangor
Runoff Coefficient C : Type 5 (Bare Loam, suburban
residential with Garden)
SIZE the SILT TRAP (Volume)
EARTHWORK ESC Design

Design Comply to MSMA guidelines
(Non-numerical design)
Determine the flow direction provide earth drains to
divert runoff to the silt trap
Determine locations for check dam to slow down the
flow
Determine locations of silt fence to avoid spill over of
muddy water into existing road & drainage system
EARTHWORK PLAN:
SILT TRAP
SILT TRAP
EARTHWORK SECTIONS:
DESIGN PLANFORM IMAGES

VIEW A
VIEW A
VIEW B
VIEW B
ROAD AND DRAINAGE

SCOPE OF ROAD AND DRAINAGE WORKS
INVOLVES:
Construct road system serving the development
Junction design
Storm water detaining system
Drainage system for the development
ROAD WORK Design Compliances

To match surrounding levels
To allow future connectivity of road system
To meet local authorities / JKR requirements
ROAD WORK Design

TYPICAL LOCAL ROADS
6m Full 6m premix
12m 7.32m premix
15m 9.0m premix
20m- 9m or 4-lane 7.2m premix
ROAD - Design
Road structure
follow local authorities
or JKR standard
ROAD - Design
Road Junction
-
Minimum radius to comply

Minimum acceleration and deceleration distance (depends on design speed)
ROAD - Design
Road Alignment & super elevation

for truck road or highway design
ROAD - Design
Road Signage
follow local authorities
or JKR standard
DRAINAGE
Urban Stormwater Management Manual for Malaysia,
published by Department of Irrigation and Drainage.
TWO MAJOR Design Objectives:

Storm water management
+ Ensure post-development run-off are contain
within the development
Hydraulic Design
+ ensure hydraulic structures have adequate
capacity to channel run-off
DRAINAGE storm water management

STORM WATER MANAGEMENT:MANAGEMENT
POST DEVELOPMENT DISCHARGE <

PRE-DEVELOPMENT DISCHARGE

Methods to control postdevelopment run-off.
Landscape/open space
Underground system
Landscape/park

Design of detention system
Establish type of detention system
Define Average Recurrent interval (ARI)
Define the catchment area
Determine the Permissible Site Discharge (PSD)
Determine the Site Storage Requirement (SSR)
Determine the outlet & emergency spillway sizes
Size the retention system
Computer-aided programs

Channel rain water
to OSD system
Overflow outlet
Volume size the

OSD (SSR)
OUTLET limit the discharge
(PSD)
DRAINAGE OSD using underground system
UNDERGORUND OSD
DRAINAGE OSD using open space
Open Space
OSD
IN
OU
T
DRAINAGE hydraulic design

Design consideration
Define Average Recurrent interval (ARI) for varies
type of drainage system (minor / major)
Define the catchment area
Determine the type of drains
Type of hydraulic structures

Drains open, closed, covered
Culvert round, rectangular
Open channel main drain, lined/unlined

Design
Manning equation
Minimum & Maximum velocity, 0.8m/s and 4.0 m/s
Sample Drainage design sheet

Open drain
Culvert (Box)
Covered drain

Lined Main Drain
Main drain
Unlined Drain/river
SEWERAGE
SCOPE OF SEWERAGE RETICULATION
WORKS INVOLVES
INVOLVES::
Design external sewerage reticulation serving the
development
Connect to existing sewer reticulation OR propose
NEW sewage treatment plant (STP) or sewage pumping
station (NPS)
SEWERAGE
Sewerage Network
Sewage Treatment Plant
SEWERAGE
Design compliance (3)
Guidelines for Developers on the Design and
Installation of Sewerage System.
M.S. 1228 : 1991 Code of Practice for Design
and Installation of Sewerage System.
Population Equivalent (PE) refer to SPANs
Table
SEWERAGE
Basic PE table base on type of premises
PE Tabulations
SEWERAGE
Sewerage Planning Proposal (PDC/1)
1. Connect to existing sewer main
2. Construct own STP (Advice on reserve &
set back compliance)
3. Construct New Pump Station (NPS)
advise on land reserve & set back
compliance
SEWERAGE
Buffer Zone Requirement
- Open plant > 30m
- Enclosed plant >10m
- Pump station > 20m
Land Area Requirement

-
Depend on the TOTAL PE of the development
SEWERAGE PLAN:
STP Reserve &

buffer zone
IN
OU
T
SEWERAGE RETICULATION - design

Sewerage Reticulation Design (PDC/2)
1.
2.
3.
4.
5.
6.
7.
8.
Maximum manhole spacing <90m

Manholes to be located at ALL the junctions
Minimum flow velocity > 0.8 m/s
Maximum flow velocity < 4.0 m/s
VCP, HDPE, Concrete or Cast Iron pipes
Sewer discharge = 50 gal/person/day
Peak Factor = 4.7x(PE/1000)-0.11
Hazen-Williams Equation as stated below:
V = 0.849 CR0.63S0.54
Q = AV
V = velocity in meters per second
C = Hazen-Williams coefficient
R = A/P = 0.25D
D = diameter in millimeter
S = pipe gradient
SEWERAGE RETICULATION - Design
Sewerage Reticulation Design Sheet
SEWERAGE RETICULATION
HDPE Pipe
VCP Pipe
Laying of sewer pipe & Manhole
Concrete Pipe
SEWERAGE TREATMENT PLANT

Compact STP
Sewage Treatment Plant (STP)

Design Effluent Discharge
1. Biochemical Oxygen Demand
BOD5 <20mg/l
2. Suspended Solids (SS) < 50mg/l
SEWERAGE TREATMENT PLANT
Mechanical STP
extended aeration plant
Aerated Lagoon Plant
WATER SUPPLY
Scope of external water reticulation works involves:
Design external
development
water
reticulation
serving
the
Connect to existing water main (incoming main)

Design of suction tank, pumping station and reservoir
(if so required)
WATER SUPPLY
Water Resources &

water treatment
Domestic water supply
WATER SUPPLY - Scope
Incoming main
From Water Main Apply to local water authority
Distribution net work
Suction, pumping
or reservoir, if
required
WATER SUPPLY
Design Guidelines
SPANs Guidelines UNIFORM TECHNICAL GUIDELINES
WATER RETICULATION AND PLUMBING
Water Demand calculations refer to SPANs Table
Determine Highest Supply Level (HSL)
WATER SUPPLY
Design compliance
1.
2.
3.
4.
5.
6.
7.
8.
9.
Maximum head losses gradient <2:1000 for Peak flow analysis

The C value used in Hazen-William = 100.
The Peak Flow factor = 1.2 for supply to service reservoir and 2.5 for the
reticulation main.
Minimum residual head above the highest supply level (HSL) > 7.5m
Minimum residual pressure above the highest supply level shall (HSL) >
4.5m where supply is directly from elevated storage tank.
Minimum residual pressure > 7.5m from platform level based on average
flow plus fire flow analysis.
Maximum residual pressure at any node < 30.0m for both peak flow and
fire flow analysis.
For average flow plus fire flow analysis, draw-off at 300 gpm (22.73 lps) is
used for one hydrant.
Minimum pipe size of reticulation main shall be 150mm diameter.
WATER SUPPLY
Design HARDY CROSS Method
The network analysis for water distribution system is using
Hardy Cross method and Hazen-Williams equation:
Hf = 10.7 Q1.85
C1.85 D4.87
whereHf = frictional head loss (m)
C = pipe roughness coefficient, 100
Q = flow in pipe (m3/s)
D = internal diameter of pipe (m)
WATER SUPPLY
Design result table
Ensure the residual

head is MORE than
7.6m
EXTERNAL WATER PLAN:
WATER SUPPLY
SUCTION TANK, PUMPING STATION & RESERVOIR
The need depends on the location, water demand of the
development.
Elevated reservoir =
2/3 Storage
Pump house
Suction Tank =
1/3 Storage
WATER SUPPLY
SUCTION TANK, PUMPING STATION & RESERVOIR
Determine BWL for reticulation
Residual head > 4.5m
Incoming MUST able to reach

Suction Tank Inlet
CIVIL WORK DESIGN
THE END
THANK YOU
PREPARED BY:

Infra Design

Uploaded by

Copyright:

Available Formats

Infra Design

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Infra Design

Uploaded by

Copyright:

Available Formats

CIVIL WORK DESIGN

1.0 BASIC SCOPE OF CIVIL WORKS

Road & Drainages

1.0 BASIC SCOPE OF CIVIL WORKS

1.0 OTHER SCOPE OF CIVIL WORKS

Highway & Bridges

1.0 OTHER SCOPE OF CIVIL WORKS

EARTHWORK Design info

EARTHWORK Design Considerations

EARTHWORK Design Compliances

EARTHWORK Platform Design

EARTHWORK Volume Calculation

Methods to calculate earthwork cut & fill:

EARTHWORK Slope Design

EARTHWORK Retaining system

EARTHWORK Retaining wall Design

EARTHWORK ESC Design

SIZE the SILT TRAP (Volume)

EARTHWORK ESC Design

DESIGN PLANFORM IMAGES

ROAD AND DRAINAGE

ROAD WORK Design Compliances

ROAD WORK Design

Minimum radius to comply

Road Alignment & super elevation

TWO MAJOR Design Objectives:

DRAINAGE storm water management

POST DEVELOPMENT DISCHARGE <

DRAINAGE storm water management

DRAINAGE storm water management

DRAINAGE storm water management

Volume size the

DRAINAGE OSD using underground system

DRAINAGE OSD using open space

DRAINAGE hydraulic design

Type of hydraulic structures

DRAINAGE hydraulic design

DRAINAGE hydraulic design

Sample Drainage design sheet

DRAINAGE hydraulic design

DRAINAGE hydraulic design

Sewage Treatment Plant

Land Area Requirement

Depend on the TOTAL PE of the development

STP Reserve &

SEWERAGE RETICULATION - design

Maximum manhole spacing <90m

SEWERAGE RETICULATION - Design

Sewerage Reticulation Design Sheet

Laying of sewer pipe & Manhole

SEWERAGE TREATMENT PLANT

Sewage Treatment Plant (STP)

SEWERAGE TREATMENT PLANT

Aerated Lagoon Plant

Connect to existing water main (incoming main)

Water Resources &

Domestic water supply

WATER SUPPLY - Scope

From Water Main Apply to local water authority