1824 08 PDF

HB envirochap8.
qxd
3/2/2006
9:06 AM
Page 239
Environmental
Measurement
U.S. Environmental Protection Agency (EPA) . . . . . . . . . . . . . . . . . 241
National Ambient Air Quality Standards (NAAQS) . . . . . . . . . . . . 241
Air Quality Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Airborne Contaminants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Liquids, Vapors, Aerosols, Sea Salt Mist
Table Classifying Chemically Active Contaminants: Liquid
Aerosols
Solid Contaminants
Table Classifying Airborne Particulates
Gas Contaminants
Table Classifying Reactive Environments & Terminology
HB envirochap8.qxd
3/2/2006
9:06 AM
Page 241
Chapter 8/Environmental Measurement 241
U.S. Environmental Protection Agency

The U.S. Environmental Protection Agency is perhaps the single best
source of information regarding environmental rules, regulations and
topics. EPAs mission is to protect human health and the environment.
Readers seeking EPA-related information are encouraged to go to EPAs
web site:
http://www.epa.gov
All topics covered by EPA are listed alphabetically with links to locate
detailed information at:
http://www.epa.gov/ebtpages/alphabet.html
U.S. National Ambient Air Quality Standards
The U.S. Clean Air Act, last amended in 1990, requires the U.S. Environmental Protection Agency (EPA) to set National Ambient Air Quality
Standards (NAAQS) for pollutants considered harmful to public health
and the environment. The Clean Air Act established two types of
national air quality standards. Primary standards set limits to protect
public health, including the health of sensitive populations such as
asthmatics, children, and the elderly. Secondary standards set limits to
protect public welfare, including protection against decreased visibility,
damage to animals, crops, vegetation, and buildings. The EPA Office of
Air Quality Planning and Standards (OAQPS) established National
Ambient Air Quality Standards for seven principal pollutants, called
criteria pollutants. They are listed in the following table. Units of
measure for the standards are parts per million (ppm) by volume, milligrams per cubic meter of air (mg/m3), and micrograms per cubic
meter of air (g/m3).
HB envirochap8.qxd
242
3/2/2006
9:06 AM
Page 242
ISA Handbook of Measurement Equations and Tables
National Ambient Air Quality Standards

Pollutant
Primary
Standards
Averaging
Times
Secondary
Standards
Carbon
Monoxide
9 ppm (10 mg/m3)
8-hour1
None
35 ppm (40 mg/m3)
1-hour1
None
Lead
1.5 g/m3
Quarterly
Average
Same as Primary
Nitrogen
Dioxide
0.053 ppm
(100 g/m3)
Annual
Same as Primary
(Arithmetic Mean)
Particulate
Matter (PM10)
50 g/m3
Annual2
(Arith. Mean)
150 ug/m3
24-hour1
15.0 g/m3
Annual3
(Arith. Mean)
65 g/m3
24-hour4
0.08 ppm
8-hour5
Same as Primary
0.12 ppm
1-hour6
Same as Primary
0.03 ppm
Annual
(Arith. Mean)
0.14 ppm
24-hour1
Particulate
Matter (PM2.5)
Ozone
Sulfur Oxides
3-hour1
Same as Primary
Same as Primary
0.5 ppm
(1300 g/m3)
1 Not to be exceeded more than once per year.

2 To attain this standard, the expected annual arithmetic mean PM concentration at each monitor
10
within an area must not exceed 50 g/m3.
3 To attain this standard, the 3-year average of the annual arithmetic mean PM
2.5 concentrations from
3
single or multiple community-oriented monitors must not exceed 15.0 ug/m .
4 To attain this standard, the 3-year average of the 98th percentile of 24-hour concentrations at each population-oriented monitor within an area must not exceed 65 g/m3.
5 To attain this standard, the 3-year average of the fourth-highest daily maximum 8-hour average ozone
concentrations measured at each monitor within an area over each year must not exceed 0.08 ppm.
6 (a) The standard is attained when the expected number of days per calendar year with maximum
hourly average concentrations above 0.12 ppm is <= 1.

(b) The 1-hour NAAQS will no longer apply to an area one year after the effective date of the designation of that area for the 8-hour ozone NAAQS. The effective designation date for most areas is June 15,
2004. (40 CFR 50.9; see Federal Register of April 30, 2004 [69 FR 23996].
HB envirochap8.qxd
3/2/2006
9:06 AM
Page 243
Air Quality Index

The Air Quality Index (AQI) is an index for reporting daily air quality. It
tells how clean or polluted the air is, and what associated health effects
might be a concern. The AQI focuses on why health effects might be
experienced within a few hours or days after breathing polluted air. EPA
calculates the AQI for five major air pollutants regulated by the Clean
Air Act: ground-level ozone, particle pollution (also known as particulate
matter), carbon monoxide, sulfur dioxide, and nitrogen dioxide. An AQI
value of 100 generally corresponds to the national air quality standard
for the pollutant, which is the level EPA has set to protect public health.
AQI values below 100 are generally thought of as satisfactory. When
AQI values are above 100, air quality is considered to be unhealthy at
first for certain sensitive groups of people, then for everyone as AQI values get higher. To make it easier to understand, the AQI is divided into
six categories:
Air Quality Index
(AQI) Values
Levels of Health
Concern
Colors
When the AQI

is in this range:
...air quality
conditions are:
...as symbolized
by this color:
0 to 50
Good
Green
51 to 100
Moderate
Yellow
101 to 150
Unhealthy for
Sensitive Groups
Orange
151 to 200
Unhealthy
Red
201 to 300
Very Unhealthy
Purple
301 to 500
Hazardous
Maroon
Each category corresponds to a different level of health concern. The

six levels of health concern and what they mean are:
Good The AQI value for your community is between 0 and 50. Air
quality is considered satisfactory, and air pollution poses little or no
risk.
Moderate The AQI for your community is between 51 and 100.
Air quality is acceptable; however, for some pollutants there may be
a moderate health concern for a very small number of people. For
example, people who are unusually sensitive to ozone may experience respiratory symptoms.
HB envirochap8.qxd
244
3/2/2006
9:06 AM
Page 244
Unhealthy for Sensitive Groups When AQI values are between

101 and 150, members of sensitive groups may experience health
effects. This means they are likely to be affected at lower levels than
the general public. For example, people with lung disease are at
greater risk from exposure to ozone, while people with either lung
disease or heart disease are at greater risk from exposure to particle
pollution. The general public is not likely to be affected when the AQI
is in this range.
Unhealthy Everyone may begin to experience health effects
when AQI values are between 151 and 200. Members of sensitive
groups may experience more serious health effects.
Very Unhealthy AQI values between 201 and 300 trigger a health
alert, meaning everyone may experience more serious health effects.
Hazardous AQI values over 300 trigger health warnings of emergency conditions. The entire population is more likely to be affected.
HB envirochap8.qxd
3/2/2006
9:06 AM
Page 245
Airborne Contaminants
An ISA standard, ISA-71.04-1985, Environmental Conditions for Process
Measurement and Control Systems: Airborne Contaminants, classifies
airborne contaminants that may affect process measurement and control instruments. The standard establishes airborne contaminant
classes for fixed (non-mobile) installations during normal operation
(non-emergency conditions) or during transportation and storage. The
classification consists of a class contaminant letter followed by a severity identification numeral.
Airborne Contaminants Liquids, Vapors, Aerosols, Sea Salt Mist

Liquids This refers to liquids that will corrode unprotected equipment and are typically transported to the equipment by condensation,
rain, splashing liquids, or cleaning fluids sprayed from hoses. The
majority of these are not classified, but should be specified to the manufacturers of equipment by special classification LX.
Vapors Solvents sometimes occur as vapors which may condense
and form puddles that become corrosive to instruments and controls.
Aerosols Aerosols are liquids carried in gas or air in the form of
small droplets generating mists. Aerosols can vary in composition and
are a major source of chemical contamination to equipment.
Sea Salt Mist Class LC1: Inland more than 0.5 km from shore;
Class LC2: Inland less than 0.5 km from shore; Class LC3: Offshore
installations (oil rigs, etc.)
HB envirochap8.qxd
246
3/2/2006
9:06 AM
Page 246
Classification of Chemically Active Contaminants:

Liquid Aerosols (Measured in g/kg except as specified)
Severity
Level 1
Severity
Level 2
Severity
Level 3
Severity
Level X
(special)
Contaminant
Class
Value
Value
Value
Value
Vapors*
LA
< 1.0
< 5.0
< 20.0
20.0
Oils
LB
< 5.0
< 50.0
< 100.0
100.0
Sea salt mist
LC
More than
0.5 km
inland
Within 0.5
km inland
Offshore
installation
T.B.S.
Special T.B.S.
LX
T.B.S.
T.B.S.
T.B.S.
T.B.S.
*For example, trichloroethylene (CHClCCl2)

NOTES:
1.0 g/kg = 1.0 part per billion (p/109)
T.B.S. = To Be Specified
< is defined as less than
> is defined as more than
is defined as greater than or equal to
HB envirochap8.qxd
3/2/2006
9:06 AM
Page 247
Airborne Contaminants Solids

Dust is a universal contaminant and is a cause of environmentally
induced equipment failures. Failure modes may be mechanical, chemical, electrical, thermal, or magnetic. To maximize equipment reliability
and life, every effort should be made to minimize exposure to airborne
particulates. The sensitivity of control equipment to different types of
particulates varies widely. In the table below, solid particulates are
classified by size. The environment should be described in terms of
concentration severity level for each class, Classes SA through SD.
Classification of Airborne Particulates
Severity Level (concentration
measured in g/m3
Particle
Size
Class
> 1 mm
SA
< 1000
< 5000
< 10,000
10,000
100 m to
1000 m
SB
< 500
< 3000
< 5000
5000
1 m to
100 m
SC
< 70
< 200
< 350
350
< 1 m
SD
< 70
< 200
< 350
350
Notes:
m = micrometer = 0.001 millimeter
g/m3 = micrograms per cubic meter
HB envirochap8.qxd
248
3/2/2006
9:06 AM
Page 248
Airborne Contaminants Gases

Two methods have been used for environmental characterization. One is
a direct measure of selected gaseous air pollutants. The other, which can
be termed reactivity monitoring, provides a quantitative measure of the
overall corrosion potential of an environment. High values will confirm
that a severe environment exists. The reverse, however, is not necessarily
true. Industrial environments may contain a complex mixture of contaminants that interact to greatly accelerate (or retard) the corrosive action of
individual gas species. To avoid these practical difficulties, the nature of
industrial environments is defined in terms of the rate at which they react
with copper. Copper has been selected as the coupon material because
data exists which correlates copper film formation with reactive (corrosive) environments. Four levels of corrosion severity are established in
Table 3. Concentration levels of some gases that contribute to these reactivity rates are also cited:
Severity level G1: Mild An environment sufficiently well-controlled
such that corrosion is not a factor in determining equipment reliability.
Severity level G2: Moderate An environment in which the effects
of corrosion are measurable and may be a factor in determining equipment reliability.
Severity level G3: Harsh An environment in which there is a high
probability that corrosive attack will occur. These harsh levels should
prompt further evaluation resulting in environmental controls or specially designed and packaged equipment.
Severity level GX: Severe An environment in which only specially
designed and packaged equipment would be expected to survive.
Specifications for equipment in this class are a matter of negotiation
between user and supplier.
HB envirochap8.qxd
3/2/2006
9:06 AM
Page 249
Classification of Reactive Environments & Terminology

Severity Level
G1
Mild
G2
Moderate
G3
Harsh
G4
Severe
Copper
Reactivity Level
(in angstroms)*
< 300
< 1000
< 2000
2000
The gas concentration levels shown below are provided for reference purposes. They are believed to approximate the Copper Reactivity Levels stated
above, providing the relative humidity is less than 50%. For a given gas concentration, the Severity Level (and Copper Reactivity Level) can be expected
to be increased by one level for each 10% increase in relative humidity above
50% or for a relative humidity rate of change greater than 6% per hour.
Contaminant
Gas
Group A
H2S
<3
< 10
< 50
50
SO2,
SO3
<10
< 100
< 300
300
Cl2
<1
<2
< 10
10
NOx
< 50
< 125
< 1250
1250
HF
<1
<2
< 10
10
NH3
< 500
O3
<2
Reactive
Species,
Group B
Concentration
< 10,000 < 25,000

< 25
< 100
25,000
100
* Measured in angstroms after one months exposure.

mm3/m3 (cubic millimeters per cubic meter) parts per billion average for test period for the gases in Groups A and B.
The Group A contaminants often occur together and the reactivity levels include the synergistic effects of these contaminants.
The synergistic effects of Group B contaminants are not known at
this time.

1824 08 PDF

Uploaded by

Copyright:

Available Formats

1824 08 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1824 08 PDF

Uploaded by

Copyright:

Available Formats

HB envirochap8.

Chapter 8/Environmental Measurement 241

U.S. Environmental Protection Agency

ISA Handbook of Measurement Equations and Tables

National Ambient Air Quality Standards

9 ppm (10 mg/m3)

35 ppm (40 mg/m3)

1 Not to be exceeded more than once per year.

single or multiple community-oriented monitors must not exceed 15.0 ug/m .

hourly average concentrations above 0.12 ppm is <= 1.

Chapter 8/Environmental Measurement 243

Air Quality Index

When the AQI

Each category corresponds to a different level of health concern. The

ISA Handbook of Measurement Equations and Tables

Unhealthy for Sensitive Groups When AQI values are between

Chapter 8/Environmental Measurement 245

Airborne Contaminants Liquids, Vapors, Aerosols, Sea Salt Mist

ISA Handbook of Measurement Equations and Tables

Classification of Chemically Active Contaminants:

Sea salt mist

*For example, trichloroethylene (CHClCCl2)

Chapter 8/Environmental Measurement 247

Airborne Contaminants Solids

ISA Handbook of Measurement Equations and Tables

Airborne Contaminants Gases

Chapter 8/Environmental Measurement 249

Classification of Reactive Environments & Terminology

< 10,000 < 25,000

* Measured in angstroms after one months exposure.

You might also like