INSTALLATION INSTRUCTIONS SDC Key Switch Assemblies are compatible with U.S. standard, 1.125" and 1.25" mortise key cylinders and interchangeable core cylinders (not included). Compatibility with a new or existing facility mechanical key system is maintained. Standard switch assemblies are Single Gang box mounted. Assemblies equipped with narrow faceplates are mounted directly to the door frame. KEY SWITCH ASSEMBLY PROCEDURE 1. Check the key cylinder for the proper tailpiece (see below). For Single Switch assemblies, use the cloverleaf type cam. For Dual Switch assemblies, a straight cam or cloverleaf type cam may be used. If you are using an SDC supplied cylinder, both cams will be supplied. If you are using another manufacturers key cylinder, use the manufacturers equivalent.
ASSEMBLY DETAIL Switch Mounting Bracket
2. Insert the key cylinder through the front of the faceplate. Make sure the key cylinder is oriented correctly and the tailpiece is in the upright position.
Depth: 1.625" (41.28mm) All assemblies Key Cylinder SDC Part# CYL-KD
Faceplate
Locknut Adjustable Switch Assembly
3. While holding the key cylinder in place, slide the switch mounting bracket onto the back of the cylinder. Align the triangular tabs on the mounting bracket with the corresponding notches on the barrel of the key cylinder. On the 700/700N/700T/800/800T/800AL Series, the bracket mounting holes will align with the faceplate mounting holes. On the 800N/800ALN Series, the mounting bracket will screw directly to the back of the faceplate. 4. Secure the key cylinder by screwing the supplied Locknut to the back of the cylinder. Tighten firmly. Insert key into the cylinder and verify the activation of the switch(es) by turning the key. If necessary, adjust the switch position to ensure that the cam makes contact with the center of the switch plunger. The switch height should be adjusted so that the cam does not apply excessive downward pressure to the switch.
5. Once the electrical connections are completed, mount the key switch assembly: For the 700/800/800AL Series, attach to a single gang mortise or surface mounted box. For the 700T/800T Series, attach to a double gang mortise or surface mounted box. For the 700N/800N/800ALN Series, See the frame preparation illustrations on Page 2.
Use tailpiece supplied with SDC Part# CYL-KD, or key cylinder manufacturers equivalent. TAILPIECE Compatible with all dual switch assemblies. Models x07 x13
ACTUAL SIZE
STANDARD FEATURES Compatible with 1-1/8 and 1-1/4 standard and interchangeable core mortise key cylinders (supplied by others). Key cylinder recessed for tamper resistance. (all except 700N Series) Tamper resistant spanner screws. Anti-tamper plugs (800 Series) Contact Rating: 6 amps @ 30VDC. Wire Leads: 7", 22 gauge. Large actuator assembly for positive & consistent circuit activation.
REV D
FACEPLATE DIMENSIONS 700: 4.5"H x 2.875"W x 20 Ga. 700N: 4.5"H x 1.75"W x 20 Ga. 700T: 4.5"H x 4.5"W x 20 Ga. 800/800AL: 5"H x 3.25" W x 0.25"D 800N/800ALN: 5.5"H x 1.75" W x 0.25"D 800T: 5"H x 5" W x 0.25"D
ASSEMBLY TOOLS: For convenience, a small spanner tool is provided with the assembly for fastening of spanner security screws SS-632 Standard Spanner Screw Drivers are available
OPTIONAL KEY CYLINDER
CYL-KD 1.25" Mortise Key Cylinder and (2) Keys. Two different tailpieces included P:\INSTALLATION INST\Exit Switches\INST-Mortise Cylinder.vsd
TAILPIECE Compatible with all SDC Key Switches.
03-13
Page 1
FRAME PREPARATION FOR NARROW KEY SWITCHES
Key switches fit a 1-3/4 frame. For jamb preparation make cut out as shown in Figure A OR Figure B. Using the faceplate as a template, drill and then tap for #6-32 screws. NOTE: FIGURES NOT TO SCALE
700N SERIES FRAME PREPARATION
800N/800ALN SERIES FRAME PREPARATION 4X Drill for #6-32
2X Drill for #6-32
1-1/2 [38.1]
1-1/2 [38.1] 3-1/4 [82.55]
2-3/4 [69.85]
4-5/8 [117.48]
3-3/4 [95.25]
CL
1/4 [6.35]
CL 7/16 [11.11]
FIGURE A
7/8 [22.23]
FIGURE B
KEYSWITCH WIRING INSTRUCTIONS
FOR 700/700N/700T/800/800N/800T/800AL SERIES & OPTIONS: SINGLE SPDT SWITCH WIRING
DUAL SPDT SWITCH
WIRING
Single Color LED Wiring (L1G, L1R, or L2 Option)
WHT
BLK
24VDC .02A max
Tri-Color LED Wiring (LT Option)
RED BLK GRN
ORG WHT YEL
ORG WHT YEL
NC COM NO
NC COM NO
ORG NC WHT COM NO YEL MODELS: x07 x13
MODELS: x01 x06
24VDC .02A max
- Apply +VDC to RED wire to illuminate RED
- Apply +VDC to GRN wire to illuminate GRN - Apply +VDC to both GRN & RED wire to illuminate AMBER Anti-Tamper Switch (ATS) Option Wiring
SPDT CONTACT 0.25A max
WHT ORG
COM NC
YEL
NO
NC COM NO
FOR TIMED MODELS x04 & x10 ONLY, CONNECT THE MOMENTARY CONTACT TO THE 10TD MINI TIMER AS SHOWN: WHT
