Scribd
Upload
417 views7 pages

LTE Command Sample

Uploaded by

Asep MAkmur
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
417 views7 pages

LTE Command Sample

Uploaded by

Asep MAkmur
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

eNodeBFunction High-Risk Command List

This section describes eNodeBFunction high-risk MML commands. The services will be interrupted after
the commands are executed. Therefore, exercise caution when executing the commands.

MML Command List


MOD ENODEBFUNCTION
MOD ENODEBSHARINGMODE
MOD CNOPERATOR
MOD CNOPERATORTA
MOD S1INTERFACE
BLK S1INTERFACE
RST S1INTERFACE
RMV S1INTERFACE
RMV S1
MOD S1
MOD M1
RMV M1
MOD M2
RMV M2
MOD CNOPSHARINGGROUP
BLK ENODEBFDDBBRES
BLK ENODEBTDDBBRES
ADD ABLMSG
MOD CQIADAPTIVECFG
MOD GLOBALPROCSWITCH
RST NBRENODEB
MOD CNOPERATORHOCFG
ADD EUSECTOREQMGROUP
RMV EUSECTOREQMGROUP
ADD EUSECTOREQMID2GROUP
RMV EUSECTOREQMID2GROUP
BLK CELL
DEA CELL
RMV CELL
ADD CELLOP
RMV CELLOP
MOD CELLDLPCPDSCHPA
ADD EUCELLPRIBBEQM

MOD EUCELLPRIBBEQM
ADD SFNAUXRESBIND
RMV SFNAUXRESBIND
STR PRIBBPADJUST
ADD SFNCELLBIND
RMV SFNCELLBIND
STR CELLRFLOOPBACK
RMV CDMA2000HRPDNCELL
RMV CDMA2000HRPDREFCELL
RMV EUTRANEXTERNALCELLPLMN
RMV GERANEXTERNALCELLPLMN
RMV UTRANEXTERNALCELLPLMN
RMV CDMA2000HRPDEXTCELL
RMV CDMA20001XRTTEXTCELL
RMV CDMA20001XRTTNCELL
RMV GERANEXTERNALCELL
RMV GERANNCELL
RMV EUTRANINTRAFREQNCELL
RMV EUTRANINTERFREQNCELL
RMV EUTRANEXTERNALCELL
RMV UTRANNCELL
RMV UTRANEXTERNALCELL
ADD EUCELLSECTOREQM
RMV EUCELLSECTOREQM
MOD CELLCHPWRCFG
MOD CELLDLPCPDCCH
MOD CELLDLPCPHICH
MOD EUCELLSECTOREQM
MOD EUSECTOREQMGROUP
MOD CELLOP
MOD CELL
MOD SFNAUXRESGRPBIND
MOD SFNAUXRESBIND
MOD CELLDSS
MOD BCCHCFG
MOD CELLRICALGO
MOD CELLULSCHALGO

MOD CELLALGOSWITCH
MOD CELLDLSCHALGO
MOD CELLNOACCESSALMPARA
MOD PDSCHCFG
MOD RACHCFG
MOD SRSCFG
MOD PCCHCFG
MOD PUSCHCFG
MOD PUCCHCFG
MOD ENODEBALGOSWITCH
MOD TDDRESMODESW
MOD CELLCSIRSPARACFG
MOD FDDRESMODE
MOD CELLPUCCHALGO
ADD CELLFRAMEOFFSET
RMV CELLFRAMEOFFSET
MOD CELLFRAMEOFFSET
MOD ENODEBFRAMEOFFSET
MOD BBPCOLLABORATEGRP
MOD SUPERCOMBCELL
MOD UTRANNCELL
MOD UTRANNFREQ
RMV BBPCOLLABORATEGRP
MOD ENODEBAUTOPOWEROFF
RMV CELLNRT
BLK BBPCOLLABORATEGRP
ADD EUTRANINTERFREQNCELL
MOD EUTRANINTERFREQNCELL
ADD EUTRANINTRAFREQNCELL
MOD EUTRANINTRAFREQNCELL
ADD GERANNCELL
MOD GERANNCELL
ADD CDMA2000HRPDNCELL
MOD CDMA2000HRPDNCELL
ADD CDMA20001XRTTNCELL
MOD CDMA20001XRTTNCELL
ADD UTRANNCELL

ADD INTERRATPOLICYCFGGROUP
MOD INTERRATPOLICYCFGGROUP

Modify eNodeB Function Configuration (MOD ENODEBFUNCTION)


Function
Use this command to modify an eNodeB function.

Note
This is a high-risk MML command, and therefore exercise caution when executing this command.
Running this command may cause the following major impacts:

After the eNodeB ID is changed, reset the application referenced by the eNodeBFunction MO by
running the RST APP command. If the application referenced by the eNodeBFunction MO is not
reset within 10 minutes after the eNodeB ID is changed by running this command, ALM-26245
Configuration Data Inconsistency will be reported.

If the Update eNB Configuration Via X2 Switch parameter is set to ON(On) for a neighboring
eNodeB, after the eNodeB ID is changed, the eNodeB notifies the neighboring eNodeB the changes
of active cells of the eNodeB through the X2 interfaces. The neighboring eNodeB then updates the
neighbor relationship configurations. The update takes a certain amount of time. If no active cells
exist under the eNodeB, the eNodeB will not inform the neighboring eNodeB the changes. If the
eNodeB ID is repeatedly changed within a short period, the neighboring eNodeB cannot completely
update the neighboring cell configurations. In this case, the configurations must be updated
manually or by ANR. It is recommended that the interval between two changes of the eNodeB ID be
longer than 60 seconds.

Before changing the ID of an eNodeB under which there are intra-eNodeB neighbor relationships,
you need to manually remove all neighbor relationships with cells under this eNodeB.

eNodeB Function Name will be synchronized from U2000 to the eNodeB automatically.

Parameters

ID

Name

Description

eNodeBFunctionName

eNodeB Function Name

Meaning: Indicates the name of an eNodeB function, w


GUI Value Range: 1~64 characters
Unit: None
Actual Value Range: 1~64 characters
MML Default Value: None
Recommended Value: None
Parameter Relationship: The value of eNodeBFunction
be null characters or contain any of the following chara
brackets (>), left angle brackets (<), stars (*), slashes (/
("), commas (,), semicolons (;), equal signs (=), single q

signs (+), two or more consecutive spaces, and two or m


Due to the limitations defined in 3GPP TS 36.413 for th
eNodeBFunctionName can contain only the following
Code for Information Interchange (ASCII): upper-case
(0 to 9), single blank ( ), left brackets ((), right brackets
(.).Messages that an eNodeB sends to an MME contain
of eNodeBFunctionName to fill the IE. All invalid char
replaced with hyphens (-) when an eNodeB sends mess
Service Interrupted After Modification: No (And no im
Impact on Radio Network Performance: None
Applicable Mode: L
eNodeBId

eNodeB ID

Meaning: Indicates the eNodeB ID defined in the servi


eNodeB within a PLMN. For details, see 3GPP TS 36.3
GUI Value Range: 0~1048575
Unit: None
Actual Value Range: 0~1048575
MML Default Value: None
Recommended Value: None
Parameter Relationship: None
Service Interrupted After Modification: Yes
Impact on Radio Network Performance: None
Applicable Mode: L

UserLabel

User Label

Meaning: Indicates user-defined remarks.


GUI Value Range: 0~256 characters
Unit: None
Actual Value Range: 0~256 characters
MML Default Value: None
Recommended Value: None
Parameter Relationship: None
Service Interrupted After Modification: No (And no im
Impact on Radio Network Performance: None
Applicable Mode: L

Example
To modify an eNodeB function with the parameters as follows: ENodeBId: 38602,
UserLabel: lte-1, run the following command:
MOD ENODEBFUNCTION: eNodeBId=38602, UserLabel="lte-1";
Parent topic: eNodeBFunction MML Commands

Huawei Proprietary and Confidential


Copyright Huawei Technologies Co., Ltd.

Modify eNodeB Sharing Mode (MOD ENODEBSHARINGMODE)


Function
Use this command to change the eNodeB sharing mode.

Note
This is a high-risk MML command, and therefore exercise caution when executing this command.
Running this command may cause the following major impacts:

After this command is executed, run RST APP to reset the application referenced by the
eNodeBFunction MO for the application to take effect. You can run LST ENODEBFUNCTION to
view the application referenced by the eNodeBFunction MO. If the application referenced by the
eNodeBFunction MO is not reset within 10 minutes after the eNodeB sharing mode is changed by
running this command, ALM-26245 Configuration Data Inconsistency will be reported.

If the eNodeB works in independent mode, only one operator can be added to the eNodeB. This
operator must be the primary operator.

When the ENodeBSharingMode parameter is changed to HYBRID_SHARED, the


CnOpSharingGroupId parameter in the associated S1Interface, X2Interface, S1, X2, Cell MOs must
be set to a valid value. In different RAN sharing modes, the maximum number of operators that can
be added and the restrictions for the relationship between the configurations of these MOs and
operators are different. When the eNodeB sharing mode is changed to hybrid RAN sharing from
others, the configurations of multiple MOs need to be modified at the same time. You are advised to
use CME to perform the configuration modification in batches. When using the MML command to
change the eNodeB sharing mode to hybrid RAN sharing, you are advised to remove these MOs
and then set the ENodeBSharingMode to HYBRID_SHARED. After this, re-add the MOs as
required.

Parameters

ID

Name

Description

ENodeBSharingMode

eNodeB sharing mode

Meaning: Indicates the eNodeB sharing mode, which c


common carriers, RAN sharing with dedicated carriers,
GUI Value Range: INDEPENDENT(Independent Oper
Sharing Mode), SEPARATED_FREQ(Separate Freque
RAN Sharing)
Unit: None
Actual Value Range: INDEPENDENT, SHARED_FRE
MML Default Value: None
Recommended Value: None
Parameter Relationship: None
Service Interrupted After Modification: Yes
Impact on Radio Network Performance: None

Applicable Mode: L
Example
To change the value of eNodeB sharing mode to INDEPENDENT, run the following
command:
MOD ENODEBSHARINGMODE: ENodeBSharingMode=INDEPENDENT;
Parent topic: eNodeBFunction MML Commands
Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.

You might also like