PN Test Readme V10 Feb15

Readme for
PROFINET
Device Tests
Version 1.0 Date February 2015
Readme for PROFINET Device Tests
V 1.0

As a member of PI you will have free access to the PROFINET test bundle. The goal of this test
bundle is to have all the necessary documents as well as the test systems for RT and IRT and
Security Level 1 (Net Load) combined in one bundle with all the electronic test cases to be performed
during a certification test:
http://www.profibus.com/nc/download/software-and-tools/downloads/profinet-io-test-bundle/display/
As a nonmember of PI you will find here a list of useful documents and tools to guide you through
your development of a PROFINET device. Some of the documents are with costs. Access to the
software is only granted for members.
To buy documents from PI please use the literature list and order form:
http://www.profibus.com/nc/download/general-pi-documents/downloads/literature-list-order-form1/display/
Important Hint:
For preparation of a certification test please read the document How to get a certificate for a
PROFINET device. In this document the necessary conformance declarations to be handed
over to the test lab are mentioned.
http://www.profibus.com/nc/download/test-and-certification/downloads/how-to-get-a-certificate-for-aprofinet-device/display/
Overview test strategy
This bundle is intended to be used for development support. It does not

substitute a certification test and a certificate!
Copyright PNO 2015 - All Rights Reserved
Page 2 of 7 pages
V 1.0
The bundle includes:

Table 1 Content of the ZIP file
Number
Document / Software
Version
Overview document
1
PNIOD_Versions_for_certifications
Feb. 01st, 2015
How to get a certificate
March 2014
Important hints for development and test
May 1st, 2014
---
Disclaimer PN Test Bundle.pdf
---
---
Readme.pdf
---
Test setup V2_3 tests.pdf
Sept. 2014
General Station Description

4
GSDML Specification
V2.31
PROFINET GSD_Checker
V2.31 2014-05-12
PROFINET device test

7
PN-Tester
2.3.5.23.4427
SPIRTA extension for additional Conformance Class C tests
2.3.5.23.313
Test Specification PROFINET devices
V2.3.5.25
Net Load test / Security Level 1 test

10
Security Level 1 Tester (Net Load)
V1.3.7
11
How to install and to run the security level 1 tester.pdf
V1.3.7
12
Test Specification Security Level 1
V1.1.3
13
PI Guideline: PN IO Net Load
V1.1
Guidelines
18
PNIO-Diagnosis Guideline
V1.0
19
PNIO-Topology Guideline
V1.0
20
PNIO-IRT-Engineering-Guideline
V1.3
21
PNIO-Configure-in-run-Guideline
V1.04
22
PNIO-System-Redundancy-Guideline
V1.08
23
Profile-Guideline I&M
V2.0
24
Profile-Guideline PROFIenergy
V1.1Ed.2
25
Profile-Guideline PROFIsafe
V2.6.1
PN-Specification
14
Overview and guidance for PROFINET specifications
V2.3
15
PROFINET Application layer Service specification
V2.3Ed.2MU2
16
PROFINET Application layer Protocol specification
V2.3Ed.2MU2
17
PROFINET Profile specification
V2.3Ed.2MU2
Test Case Specification

26
TCS_V2.32_00000001_DiffAccessWays_V_01.00
V01.00
Page 3 of 7 pages
V 1.0
Number
Document / Software
Version
27
TCS_V2.32_00000002_Pdev_Read_V_01.00
V01.00
28
TCS_V2.32_00000003_Pdev_Check_V_01.00
V01.00
29
TCS_V2.32_00000004_Pdev_Adjust_V_01.00
V01.00
Table 1 number 1:
This document shall give you an overview about the current test possibilities. Please read first!
Table 1 number 2:
This document shall give you an overview about the certification.
Table 1 number 3:
Important document with hints for development and test of a PROFINET device.
Table 1 number 4:
In this area you can find a description how to write the GSDML file for your device. Here also are
attached examples and style sheets.
Table 1 number 5:
With the help of this software you can check the correctness of GSDML files.
Table 1 number 6:
These slides describe in an overview the requirements, setup and configurations for PN tests.
Table 1 number 7:
For the requirements please see the manual and the Test Specification PN IO devices V2.3.5.24.
The test setup is described in the document Test Specification PN IO devices V2.3.5.24.
The test case TOPO-TED may fail in the first run, then this test case a second time is run and
checked then. For checking Topology see also: http://ted-check.profibus.cz/
Table 1 number 8:
For the requirements please see the manual and the Test Specification PN IO devices V2.3.5.24.
The test setup is described in the document Test Specification PN IO devices V2.3.5.24.
The test case ReductionRatio may fail with the information that Too few Ping responses received.
In that case this test case shall be checked in a suitable way.
Table 1 number 9:
This document describes which tests have to be done in an authorized PROFINET test laboratory to
get a PROFINET certificate for a new developed PROFINET device.
Table 1 number 10:
PROFINET Security Level 1 Tester
For the simple execution of the security tests level 1 according the guidelines the PNO offers a test
environment. It can be used as a means for preparation of the optional certification for PROFINET
devices.
For the Minimum System Requirements please read the Test Specification Security Level 1 V1.1.3
document.
Table 1 number 11:
This document describes the installing and test preparation of the software for the Security Level 1
(Net Load) tester.
Page 4 of 7 pages
V 1.0
Table 1 number 12:

In this document the test, requirements and the test setup for Security Level 1 (Net Load) is described.
Table 1 number 13:
The goals of this paper are:
Definition of a uniform behavior for devices under different network loads.
Definition of network load limits.
Definition of appropriate reactions regarding the related network load limits.
Table 1 number 14 to 17:
These are the actual valid PROFINET specifications (V2.3 Ed.2 MU2).
Table 1 number 18:
This PI Guideline describes the handling and usage of diagnosis.
Table 1 number 19:
This PI Guideline describes the handling, requirements and usage of Topology discovery.
Table 1 number 20:
This PI Guideline describes the handling, requirements and usage of IRT engineering.
Table 1 number 21:
This PI Guideline describes the handling, requirements and usage for dynamic reconfiguration.
Table 1 number 22:
This PI Guideline describes the handling, requirements and usage of system redundancy.
Table 1 number 23:
This PI Guideline describes the handling, requirements and usage of I&M.
Table 1 number 24:
This PI Guideline describes the handling, requirements and usage of profile PROFIenergy.
Table 1 number 25:
This PI Guideline describes the handling, requirements and usage of profile PROFIsafe.
Table 1 number 26 to 29:
These are the actual valid Test Case specifications that extend the file Test Specification PROFINET
devices.
Helpful Tools:
PRONETA you can download at: http://support.automation.siemens.com/WW/view/en/67460624
Topology checking tool available at: http://ted-check.profibus.cz/
If you have any questions please contact the test lab where you intend to perform the
certification test.
Please read the test specification for applying a certification test. The specification is part of the PN
http://www.profibus.com/nc/download/software-and-tools/downloads/profinet-io-testTest
Bundle
bundle/display/.
To obtain an application contract please contact the test lab. The actual list of testlabs with the internet
addresses is available on http://www.profibus.com/pi-organization/institutions-support/test-labs/
Page 5 of 7 pages
V 1.0
Issuing the certificate

After passing the certification test successfully you will get a test report. Send this test report together
with an application form to PI certification office to apply for a certificate. You will find the form here:
http://www.profibus.com/nc/download/device-application-forms/downloads/application-form-for-acertificate/display/
Do not sell your PROFINET device without a valid certificate!

Certification is mandatory for PROFINET devices!
Beware of patents
The
patents
from
this
list:
http://www.profibus.com/nc/download/general-technologydocuments/downloads/list-of-patents-to-profibus-profisafe-profidrive-and-or-profinettechnology/display/?submit_logout=Log+out&logintype=logout&pid=7&redirect_url=http%3A%2F%2F
www.profibus.com%2F are granted to all members of PI for products being equiped with a
PROFNET interface.
Nonmembers of PI are responsible for protecting themselves against liability for
infringement of patents.
The PROFINET logo is registered trade mark. The use is restricted to members of PI.
Use of the PROFINET trademark, test and certification
PNO is entitled to grant licenses in respect of the trademark "PROFINET" (word formation trademark)
applied for in the Federal Republic of Germany and in respect of all corresponding applications and/or
registrations outside Germany (referred to hereinafter collectively as "TRADEMARK").
The Member is entitled, following certification of its equipment by PNO, to use the TRADEMARK on
such certified equipment, relevant documentation, promotional material etc.
In order to obtain such a certificate the applicant shall have passed a certification test at a test
laboratory accredited by PNO successfully.
Once the certification test has been successfully, PNO shall issue a certificate to the Member.
The Member shall not in any country initiate any applications in respect of the TRADEMARK or any
other trademarks that might be mistaken for it.
If the Member is intending to sell his certified products in countries in which PNO has no trademark
application or registration, the parties shall agree upon which party shall bear the costs arising from
such applications.
It is understood that this agreement does not provide the Member with any right in respect of the
Trademark other than that of using the TRADEMARK in accordance with the provisions of this
agreement, and that the Member shall not, out of use of the TRADEMARK, derive any claims against
PNO.
Page 6 of 7 pages
V 1.0
Copyright by
PROFIBUS Nutzerorganisation e. V. (PNO)

PROFIBUS & PROFINET International (PI)
Haid-und-Neu-Str. 7 76131 Karlsruhe Germany
Phone +49 721 96 58 590 Fax +49 721 96 58 589
E-mail [email protected]
www.profibus.com www.profinet.com
Page 7 of 7 pages

PN Test Readme V10 Feb15

Uploaded by

Copyright:

Available Formats

PN Test Readme V10 Feb15

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PN Test Readme V10 Feb15

Uploaded by

Copyright:

Available Formats

Readme for

Version 1.0 Date February 2015

Readme for PROFINET Device Tests

Readme for PROFINET Device Tests

Overview test strategy

This bundle is intended to be used for development support. It does not

Readme for PROFINET Device Tests

The bundle includes:

Feb. 01st, 2015

How to get a certificate

Important hints for development and test

May 1st, 2014

Disclaimer PN Test Bundle.pdf

Test setup V2_3 tests.pdf

General Station Description

PROFINET device test

SPIRTA extension for additional Conformance Class C tests

Test Specification PROFINET devices

Net Load test / Security Level 1 test

Security Level 1 Tester (Net Load)

How to install and to run the security level 1 tester.pdf

Test Specification Security Level 1

PI Guideline: PN IO Net Load

Overview and guidance for PROFINET specifications

PROFINET Application layer Service specification

PROFINET Application layer Protocol specification

PROFINET Profile specification

Test Case Specification

Copyright PNO 2015 - All Rights Reserved

Readme for PROFINET Device Tests

Copyright PNO 2015 - All Rights Reserved

Readme for PROFINET Device Tests

Table 1 number 12:

Copyright PNO 2015 - All Rights Reserved

Readme for PROFINET Device Tests

Issuing the certificate

Do not sell your PROFINET device without a valid certificate!

Copyright PNO 2015 - All Rights Reserved

Readme for PROFINET Device Tests

PROFIBUS Nutzerorganisation e. V. (PNO)

Copyright PNO 2015 - All Rights Reserved

You might also like