Scribd
Upload
62 views

Department of Mechanical and Industrial Engineering Northeastern University

In this tutorial you learn 3D Part Modeling and sketch control. We create three parts: pin, rectangular plate, and base plate. Dimensions of the pin are shown in the image below.

Uploaded by

IvanZavaleta
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
62 views

Department of Mechanical and Industrial Engineering Northeastern University

In this tutorial you learn 3D Part Modeling and sketch control. We create three parts: pin, rectangular plate, and base plate. Dimensions of the pin are shown in the image below.

Uploaded by

IvanZavaleta
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 46

DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING

NORTHEASTERN UNIVERSITY
CAPSULE PROGRAM
Funded by NSF grant #0833636

Tutorial 02
3D Part Modeling

SolidWorks 2010
Copyright 2010 Prof. Zeid

3D Part Modeling
In this tutorial you learn 3D part modeling and sketch control. We create three parts: pin,
rectangular plate, and base plate
Pin
Step 0: General Planning Strategy:
We shall create the part shown in the image below. Listed below the figure are the steps
in brief that we must perform to create the part.

1. Create and revolve the profile.

Creating the Pin


Step 1
File New Part

Step 2
Select Front Plane from the feature manager

Step 3
Select Front View from view orientation icon

Step 4
Go to Tools Options

Step 5
Go to Document properties Units IPS

The IPS unit is selected for the drawing. The drawing will now have inches as its unit.

Step 6
Select Sketch Tab
Then select Line Icon

2) Select Line Icon

1) Select Sketch Tab

Step 7
Draw the drawing as per required dimensions

Once you finish drawing select


OK
When you select line icon a red
axis point will appear. Start the
drawing from the red point.

10

Step 8
Go to Features Tab Reference Geometries Axis

11

Step 9

4) After drawing axis


select ok

3) Click mouse here (end


point)

1) One line/edge/axis

2) Click mouse here (start


point)

12

Step 10
Now we are ready to perform the revolve operation.

13

Step 11
Go to Feature Manager and select Sketch
Then select Revolved Boss/Base icon

2) Select Revolved Boss/Base


icon

1) Select Sketch

14

Step 12

1) Select the blue box

2) Select the axis

15

Step 13
The rotated entity preview will be shown as in the image below

1) Select Ok

16

The rotated entity preview will be shown as in the image below

17

The rotated entity preview will be shown as in the image below

18

The dimensions of the pin are shown in the image below.

19

Rectangular Plate
General Planning Strategy
We shall create the part shown in the image below. Listed below the figure are the steps
in brief that we must perform to create the part.

2. Create the profile and extrude it to create the plate.


3. Create the hole.

20

Step 1
Create the part file and draw the rectangle according to required dimensions. For creating
part file and drawing refer to the pin tutorial.

21

Step2
After completing the drawing change the view to isometric and select OK.

1) Select Isometric view


2) Select Ok

22

Step 3
Select sketch from the Feature Manager.

23

Step 4
Select Extruded Boss/Base from Features Tab. Enter the dimension as 3 inches.

3) Select OK
1) Select Extruded
Boss/base

2) Enter dimension as 3
inches

24

Preview of the rectangular plate.

25

Step 5
Select the top plane of the rectangular plate.

26

Step 6
Go to View Icon and select Normal To option

27

Step 7
Select Circle Icon.

28

Step 8
Draw a circle of diameter 1 inch. Adjust the placement of the circle using smart
dimension option. Tutorial 1 has the steps on how to use the smart dimension option.

1) After drawing the circle


select OK

29

Preview of the Rectangular plate.

30

Step 9
Select sketch from the Feature Manager.

31

Step 10
Go to Features TabExtruded Boss/base. Select the option Through All.

1) Select the option


Through all

32

Preview of the completed Rectangular Plate.

33

This completes the model. Shown below is the dimensioned drawing view of the model
that we just created.

34

Base Plate
General Planning Strategy
We shall create the part shown in the image below. Listed below the figure are the steps
in brief that we must perform to create the part.

4. Create the profile and extrude it to create the plate.


5. Create the hole.

35

Step 1
Create the part file and draw the figure according to required dimensions. For creating
part file and drawing refer to the pin tutorial.

36

Step 2
View the drawing in Isometric View. Select sketch from the Feature Manager.

37

Step 3
Go to Features Tab Extruded Boss/base and extrude the figure to a length of 3 inches.
Select Ok (green tick mark on top right corner) to complete extrusion.

38

Preview of the extruded part.

39

Step 4
Select the plane as shown in the figure below.

40

Step 5
Select Normal To option from the View Icon.

41

Step 6
Draw a circle of diameter 1 inch. Position the circle using smart dimension option.
Follow the steps given in the tutorial for rectangular plate on how to use the smart
dimension option. Select OK to complete the process.

42

Step 7
Select the circle sketch from the Feature Manager Window.

43

Step 8
Go to Features Tab Extruded Boss/base and use the option Through All. Select OK
to complete the extrusion.

44

Preview of the completed model.

45

This completes the model. Shown below is the dimensioned drawing view of the model
that we just created.

Save the models with the name pin, rectangular plate and base plate.

46

You might also like