0% found this document useful (0 votes)
138 views3 pages

λ-based Design Rules PDF

This document discusses λ-based design rules for integrated circuit fabrication. λ-based rules specify all dimensions as integer multiples of λ, where λ is the minimum feature size. Key guidelines include minimum line widths of 2λ for poly and diffusion, a minimum distance of 3λ between diffusion layers, a contact window size of 2λ by 2λ, and a metal wire spacing of 3λ. Well spacing depends on their potentials, with a minimum of 6λ if at different potentials and 8λ if at the same high potential. The active region length is distributed over source, drain, channel, and encroachment areas totaling 10λ.

Uploaded by

vinosuja
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
138 views3 pages

λ-based Design Rules PDF

This document discusses λ-based design rules for integrated circuit fabrication. λ-based rules specify all dimensions as integer multiples of λ, where λ is the minimum feature size. Key guidelines include minimum line widths of 2λ for poly and diffusion, a minimum distance of 3λ between diffusion layers, a contact window size of 2λ by 2λ, and a metal wire spacing of 3λ. Well spacing depends on their potentials, with a minimum of 6λ if at different potentials and 8λ if at the same high potential. The active region length is distributed over source, drain, channel, and encroachment areas totaling 10λ.

Uploaded by

vinosuja
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Module 3 : Fabrication Process and Layout Design Rules

Lecture 14 : -based Design Rules


Objectives
In this course you will learn the following
Background
-based Design Rules
14.1 Background
As we studied in the last lecture, Layout rules are used to prepare the photo mask used
in the fabrication of integrated circuits. The rules provide the necessary communication
link between the circuit designer and process engineer. Design rules represent the best
possible compromise between performance and yield.
The design rules primarily address two issues 1. The geometrical reproductions of features that can be reproduced by mask making
and lithographical processes.
2. Interaction between different layers
Design rules can be specified by different approaches
1. -based design rules
2. -based design rules
As -based layout design rules were originally devised to simplify the industry- standard
-based design rules and to allow scaling capability for various processes. It must be
emphasized, however, that most of the submicron CMOS process design rules do not
lend themselves to straightforward linear scaling. The use of -based design rules must
therefore be handled with caution in sub-micron geometries.
In further sections of this lecture, we will present a detailed study about -based design
rules.
14.2 -based Design Rules
Features of -based Design Rules: -based Design Rules have the following features is the size of a minimum feature
All the dimensions are specified in integer multiple of .
Specifying particularizes the scalable rules.
Parasitic are generally not specified in units
These rules specify geometry of masks, which will provide reasonable yields

Guidelines for using -based Design Rules:

As, Minimum line width of poly is 2 & Minimum line width of diffusion is 2

As Minimum distance between two diffusion layers 3

As It is necessary for the poly to completely cross active, other wise the transistor that
has been created crossing of diffusion and poly, will be shorted by diffused path of
source and drain.
Contact cut on metal

Contact window will be of 2 by 2 that is minimum feature size while metal deposition
is of 4 by 4 for reliable contacts.
In Metal

Two metal wires have 3 distance between them to overcome capacitance coupling and
high frequency coupling. Metal wires width can be as large as possible to decrease
resistance.
Buttering contact

Buttering contact is used to make poly and silicon contact. Window's original width is 4,
but on overlapping width is 2.
So actual contact area is 6 by 4.
The distance between two wells depends on the well potentials as shown above. The
reason for 8l is that if both wells are at same high potential then the depletion region
between them may touch each other causing punch-through. The reason for 6l is that if
both wells are at different potentials then depletion region of one well will be smaller, so
both depletion region will not touch each other so 6l will be good enough.

The active region has length 10 which is distributed over the followings 2 for source diffusion
2 for drain diffusion
2 for channel length
2 for source side encroachment
2 for drain side encroachment
Recap
In this lecture you have learnt the following
Background
-based Design Rules
Congratulations, you have finished Lecture 14.

You might also like