TJA1027

LIN 2.2A/SAE J2602 transceiver

Rev. 2 24 April 2013

Product data sheet

1. General description
The TJA1027 is the interface between the Local Interconnect Network (LIN) master/slave
protocol controller and the physical bus in a LIN network. It is primarily intended for
in-vehicle sub-networks using baud rates up to 20 kBd and is compliant with LIN 2.0,
LIN 2.1, LIN 2.2, LIN 2.2A and SAE J2602. The TJA1027 is pin-compatible with the
TJA1020 and the TJA1021.
The transmit data stream generated by the protocol controller is converted by the
TJA1027 into an optimized bus signal shaped to minimize ElectroMagnetic Emissions
(EME). The LIN bus output pin is pulled HIGH via an internal termination resistor. For a
master application, an external resistor in series with a diode should be connected
between pin VBAT and pin LIN. The receiver detects a receive data stream on the LIN bus
input pin and transfers it via pin RXD to the microcontroller.
Power consumption is very low in Sleep mode. However, the TJA1027 can still be woken
up via pins LIN and SLP_N.

2. Features and benefits

2.1 General

Compliant with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A and SAE J2602
Baud rate up to 20 kBd
Very low ElectroMagnetic Emissions (EME)
Very low current consumption in Sleep mode with remote LIN wake-up
Input levels compatible with 3.3 V and 5 V devices
Integrated termination resistor for LIN slave applications
Passive behavior in unpowered state
Operational during cranking pulse: full operation from 5 V upwards
Undervoltage detection
K-line compatible
Available in SO8 and HVSON8 packages
Leadless HVSON8 package (3.0 mm 3.0 mm) with improved Automated Optical
Inspection (AOI) capability
Dark green product (halogen free and Restriction of Hazardous Substances (RoHS)
compliant)
Pin-compatible subset of the TJA1020 and TJA1021

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

2.2 Protection
Very high ElectoMagnetic Immunity (EMI)
Very high ESD robustness: 8 kV according to IEC 61000-4-2 for pins LIN and VBAT
Bus terminal and battery pin protected against transients in the automotive
environment (ISO 7637)
Bus terminal short-circuit proof to battery and ground
Thermally protected
Initial transmit data (TXD) dominant check

3. Quick reference data

Table 1.

Quick reference data

Symbol Parameter
VBAT

battery supply voltage

IBAT

battery supply current

Conditions

Min

Typ

Max

Unit

limiting values

0.3

+42

operating range

18

Sleep mode; VLIN = VBAT; VSLP_N = 0 V

2.5

10

Standby mode; VLIN = VBAT; VSLP_N = 0 V

2.5

10

Normal mode; VLIN = VBAT; VSLP_N = 5 V;

VTXD = 5 V

200

800

1600

VLIN

voltage on pin LIN

limiting value; with respect to GND and

VBAT

42

+42

VESD

electrostatic discharge voltage

on pin LIN; according to IEC 61000-4-2

+8

kV

Tvj

virtual junction temperature

40

+150

4. Ordering information
Table 2.

Ordering information

Type number

Package
Name

Description

Version

TJA1027T/20

SO8

plastic small outline package; 8 leads; body width 3.9 mm

SOT96-1

TJA1027TK/20

HVSON8

plastic thermal enhanced very thin small outline package; no leads;

8 terminals; body 3 3 0.85 mm

SOT782-1

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

2 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

5. Block diagram

TJA1027
POWER-ON RESET &
UNDERVOLTAGE DETECTION
RXD

VBAT

1
BUS
TIMER
6

SLP_N

LIN

CONTROL

TXD

5
TEMPERATURE
PROTECTION

GND

015aaa212

Fig 1.

TJA1027

Product data sheet

Block diagram

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

3 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

6. Pinning information
6.1 Pinning
TJA1027T

TJA1027TK

terminal 1
index area

RXD

n.c.

SLP_N

VBAT

n.c.

LIN

TXD

GND

RXD

n.c.

SLP_N

VBAT

n.c.

LIN

TXD

GND

015aaa214

Transparent top view

015aaa213

a. TJA1027T/20: SO8 package

Fig 2.

b. TJA1027TK/20: HVSON8 package

Pin configuration diagrams

6.2 Pin description

Table 3.
Symbol

Pin

Description

RXD

receive data output (open-drain); active LOW after a wake-up

event

SLP_N

sleep control input (active LOW); resets wake-up request on RXD

n.c.

not connected

TXD

transmit data input

GND

5[1]

ground

LIN

LIN bus line input/output

VBAT

battery supply

n.c.

not connected

[1]

TJA1027

Product data sheet

Pin description

For enhanced thermal and electrical performance, the exposed center pad of the HVSON8 package should
be soldered to board ground (and not to any other voltage level).

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

4 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

7. Functional description
The TJA1027 is the interface between the LIN master/slave protocol controller and the
physical bus in a LIN network. According to the Open System Interconnect (OSI) model,
this is the LIN physical layer.
The LIN transceiver is optimized for, but not limited to, automotive applications with
excellent ElectroMagnetic Compatibility (EMC) performance.

7.1 LIN 2.x/SAE J2602 compliant

The TJA1027 is fully LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A and SAE J2602 compliant. The
LIN physical layer is independent of higher OSI model layers (e.g. the LIN protocol).
Consequently, nodes containing a LIN 2.2A-compliant physical layer can be combined,
without restriction, with LIN physical layer nodes that comply with earlier revisions
(LIN 1.0, LIN 1.1, LIN 1.2, LIN 1.3, LIN 2.0, LIN 2.1 and LIN 2.2).

7.2 Operating modes

The TJA1027 supports modes for normal operation (Normal mode) and very-low-power
operation (Sleep mode). An intermediate wake-up mode between Sleep and Normal
modes is also supported (Standby mode). The state diagram is shown in Figure 3.

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

5 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

falling VBAT < Vth(POR)L

Reset
RXD: floating
Transmitter: off

Normal
RXD: data output
Transmitter: on(1)

rising VBAT > Vth(POR)H

t(SLP_N = 1) > tgotonorm

t(SLP_N = 1) > tgotonorm

t(SLP_N = 0) > tgotosleep

Sleep

Standby

RXD: floating
Transmitter: off

RXD: low
Transmitter: off
t(LIN = 01; after LIN = 0) > twake(dom)LIN
015aaa215

(1) A positive edge on SLP_N triggers a transition to Normal mode; the transmitter is enabled once
TXD goes HIGH; in the event of thermal shut down, the transmitter is disabled.

Fig 3.
Table 4.

SLP_N

RXD

Transmitter

Description

Reset

floating

off

all inputs ignored; all outputs

drivers off

Sleep[1]

floating

off

no wake-up request detected

Standby[2]

LOW[3]

off

[1]

Product data sheet

Operating modes

Mode

Normal

TJA1027

State diagram

HIGH: recessive state Normal

LOW: dominant state

wake-up request detected

mode[4]

bus signal shaping enabled

The TJA1027 enters Sleep mode after a power-on reset (e.g. after switching on VBAT).

[2]

The TJA1027 will switch automatically to Standby mode if a LIN wake-up event occurs during Sleep mode.

[3]

The wake-up interrupt (on pin RXD) is released after a positive edge on pin SLP_N.

[4]

A positive edge on SLP_N will trigger a transition to Normal mode The transmitter will be off if TXD is LOW
and will be enabled as soon as TXD goes HIGH.

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

6 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

7.2.1 Reset mode

When the TJA1027 is in Reset mode, it ignores all input signals and all output drivers are
off. The TJA1027 switches to Reset mode when the voltage on VBAT drops below the
LOW-level power-on reset threshold, Vth(POR)L. When the voltage on VBAT rises above the
HIGH-level power-on reset threshold, Vth(POR)H, the TJA1027 switches to Sleep mode.

7.2.2 Sleep mode

The TJA1027 consumes significantly less power in Sleep mode than in any other mode.
Even though current consumption is extremely low in Sleep mode, the TJA1027 can still
be woken up remotely via pin LIN or activated directly via pin SLP_N. Filters on the
receiver input (LIN) and on pin SLP_N prevent unwanted wake-up events occurring due to
automotive transients or radio frequency interference. All wake-up events must be
maintained for a specific period of time (twake(dom)LIN or tgotonorm).
Sleep mode is initiated by a falling edge on pin SLP_N in Normal mode. The LIN transmit
path is immediately disabled when pin SLP_N goes LOW. In order to ensure the TJA1027
switches successfully to Sleep mode, the sleep command (pin SLP_N = LOW) must be
maintained for at least tgotosleep.
Sleep mode activation is independent of the levels on pins LIN or TXD. So the lowest
possible power consumption can be guaranteed, even when there is a continuous
dominant level on pins LIN and TXD.

7.2.3 Standby mode

Standby mode is activated automatically when a local or remote wake-up event occurs
while the TJA1027 is in Sleep mode. In Standby mode, pin RXD is held LOW to provide
an interrupt flag for the microcontroller.

7.2.4 Normal mode

In Normal mode, the TJA1027 can transmit and receive data via the LIN bus.
The receiver detects the data stream on the LIN bus input pin and transfers it via pin RXD
to the microcontroller (see Figure 6): HIGH for a recessive level and LOW for a dominant
level on the bus. The receiver has a supply-voltage related threshold with hysteresis and
an integrated filter to suppress bus line noise.
The transmit data stream from the protocol controller is detected on pin TXD and is
converted by the transmitter into an optimized bus signal shaped to minimize EME. The
LIN bus output pin is pulled HIGH via an internal slave termination resistor. For a master
application, an external resistor in series with a diode should be connected between pin
VBAT and pin LIN (see Figure 6).
If pin SLP_N is pulled HIGH while the TJA1027 is in Sleep or Standby mode, the LIN
transceiver switches to Normal mode after tgotonorm.

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

7 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

7.3 Transceiver wake-up

7.3.1 Remote wake-up via the LIN bus
A falling edge on pin LIN followed by a LOW level maintained for twake(dom)LIN followed by
a rising edge on pin LIN triggers a remote wake-up (see Figure 4). It should be noted that
the time period twake(dom)LIN is measured either in Normal mode while TXD is HIGH, or in
Sleep mode irrespective of the status of pin TXD.

LIN recessive

VBUSrec
VBUSdom

VLIN

twake(dom)LIN

LIN dominant
ground
sleep mode

standby mode
015aaa241

Fig 4.

Remote wake-up behavior

7.3.2 Wake-up via pin SLP_N

If SLP_N is held HIGH for tgotonorm, the TJA1027 will switch from Sleep mode to Normal
mode.

7.4 Operation during automotive cranking pulses

TJA1027 remains fully operational during automotive cranking pulses because the LIN
transceiver is fully specified down to VBAT = 5 V.

7.5 Operation when supply voltage is outside specified operating range

If VBAT > 18 V or VBAT < 5 V, the TJA1027 may remain operational, but parameter values
cannot be guaranteed to remain within the operation ranges specified in Table 7 and
Table 8.
In Normal mode:

If the input level on pin TXD is HIGH, the LIN transmitter output on pin LIN will be
recessive.

If the input level on pin LIN is recessive, the receiver output on pin RXD will be HIGH.
If the voltage on pin VBAT rises to 27 V (e.g. during an automotive jump start), the total
LIN network pull-up resistance should be greater than 680 and the total LIN network
capacitance should be less than 6.8 nF to ensure reliable LIN data transfer.

If the voltage on pin VBAT drops below the LOW-level VBAT LOW threshold, Vth(VBATL)L,
the LIN transmit path is interrupted and the LIN output remains recessive. The LIN
transmit path is switched on again when VBAT rises above Vth(VBATL)H and the input to
pin TXD is recessive.

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

8 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

If the voltage on pin VBAT drops below the LOW-level power-on reset threshold, Vth(POR)L,
the TJA1027 switches to Reset mode (i.e. all output drivers are disabled and all inputs are
ignored). The TJA1027 switches to Sleep mode if VBAT > Vth(POR)H.

7.6 Fail-safe features

Pin TXD provides a pull-down to GND in order to force a predefined level on the transmit
data input if the pin is disconnected.
Pin SLP_N provides a pull-down to GND in order to force the transceiver into Sleep mode
if pin SLP_N is disconnected.
Pin RXD is set floating if VBAT is disconnected.
The current in the transmitter output stage is limited in order to protect the transmitter
against short circuits to pins VBAT or GND.
A loss of power (pins VBAT and GND) has no impact on the bus line or on the
microcontroller. No reverse currents flow from the bus into pin LIN. The current path from
VBAT to LIN via the integrated LIN slave termination resistor remains. The LIN transceiver
can be disconnected from the power supply without influencing the LIN bus.
The output driver on pin LIN is protected against overtemperature conditions. If the
junction temperature exceeds the shutdown junction temperature, Tj(sd), the thermal
protection circuit disables the output driver. The driver is enabled again when the junction
temperature falls below Tj(sd) and pin TXD is recessive.
The initial TXD dominant check prevents the bus line from being driven to a permanent
dominant state (blocking all network communications) if pin TXD is forced permanently
LOW by a hardware and/or software application failure. The TXD input level is checked
after a transition to Normal mode. If TXD is LOW, the transmit path will remain disabled
and will only be enabled when TXD goes HIGH.

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

9 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

8. Limiting values
Table 5.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages are referenced to pin GND, unless
otherwise specified. Positive currents flow into the IC.
Symbol

Parameter

VBAT
VTXD

Conditions

Min

Max

Unit

battery supply voltage

0.3

+42

voltage on pin TXD

0.3

+7

VRXD

voltage on pin RXD

0.3

+7

VSLP_N

voltage on pin SLP_N

0.3

+7

VLIN

voltage on pin LIN

42

+42

VESD

electrostatic discharge voltage

with respect to GND and VBAT

according to IEC 61000-4-2

human body model
charge device model
machine model
Tvj

virtual junction temperature

Tstg

storage temperature

on pins LIN and VBAT

[1]

+8

kV

on pins LIN and VBAT

[2]

+8

kV

on pins TXD, RXD and SLP_N

[2]

+2

kV

750

+750

[3]

200

+200

[4]

40

+150

55

+150

all pins
all pins

[1]

Equivalent to discharging a 150 pF capacitor through a 330 resistor.

[2]

Equivalent to discharging a 100 pF capacitor through a 1.5 k resistor.

[3]

Equivalent to discharging a 200 pF capacitor through a 10 resistor and a 0.75 H coil.

[4]

Junction temperature in accordance with IEC 60747-1. An alternative definition is: Tj = Tamb + P Rth(j-a), where Rth(j-a) is a fixed value.
The rating for Tvj limits the allowable combinations of power dissipation (P) and ambient temperature (Tamb).

9. Thermal characteristics
Table 6.
Thermal characteristics
According to IEC 60747-1.
Symbol

Parameter

Conditions

Typ

Unit

Rth(j-a)

thermal resistance from junction to ambient

SO8 package; in free air

145

K/W

HVSON8 package; in free air

50

K/W

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

10 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

10. Static characteristics

Table 7.
Static characteristics
VBAT = 5 V to 18 V; Tvj = 40 C to +150 C; RL(LIN-VBAT) = 500 ; all voltages are referenced to pin GND; positive currents
flow into the IC; typical values are given at VBAT = 12 V; unless otherwise specified.[1]
Symbol

Parameter

Conditions

Min

Typ

Max

Unit

18

Sleep mode; bus recessive;

VLIN = VBAT; VSLP_N = 0 V

2.5

10

Sleep mode; bus dominant;

VLIN = 0 V; VBAT = 12 V;
VSLP_N = 0 V

150

400

1200

Standby mode; bus recessive;

VLIN = VBAT; VSLP_N = 0 V

2.5

10

100

300

1000

Normal mode; bus recessive;

VLIN = VBAT; VSLP_N = 5 V;
VTXD = 5 V

200

800

1600

Normal mode; bus dominant;

VTXD = 0 V; VSLP_N = 5 V;
VBAT = 12 V

mA

Supply
VBAT

battery supply voltage

IBAT

battery supply current

Standby mode; bus dominant;

VLIN = 0 V; VBAT = 12 V;
VSLP_N = 0 V

[2]

Undervoltage reset
Vth(POR)L

LOW-level power-on reset power-on reset

threshold voltage

1.6

3.1

3.9

Vth(POR)H

HIGH-level power-on reset

threshold voltage

2.3

3.4

4.3

Vhys(POR)

power-on reset hysteresis

voltage

0.05

0.3

Vth(VBATL)L

LOW-level VBAT LOW

threshold voltage

3.9

4.4

4.7

Vth(VBATL)H

HIGH-level VBAT LOW

threshold voltage

4.2

4.7

4.9

Vhys(VBATL)

VBAT LOW hysteresis

voltage

0.15

0.3

0.6

[2]

[2]

Pins TXD and SLP_N

VIH

HIGH-level input voltage

VIL

LOW-level input voltage

0.3

+0.8

50

200

400

mV

on TXD

50

125

325

on SLP_N

100

250

650

mA

+5

Vhys

hysteresis voltage

Rpd

pull-down resistance

[2]

Pin RXD (open-drain)

IOL
ILH

LOW-level output current

VRXD = 0.4 V
[2]

HIGH-level leakage
current

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

11 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

Table 7.
Static characteristics continued
VBAT = 5 V to 18 V; Tvj = 40 C to +150 C; RL(LIN-VBAT) = 500 ; all voltages are referenced to pin GND; positive currents
flow into the IC; typical values are given at VBAT = 12 V; unless otherwise specified.[1]
Symbol

Parameter

Conditions

Min

Typ

Max

Unit

40

100

mA

Pin LIN
IBUS_LIM

current limitation for driver VBAT = 18 V; VLIN = 18 V;

dominant state
VTXD = 0 V

IBUS_PAS_dom

receiver dominant input

leakage current including
pull-up resistor

VBAT = 12 V; VLIN = 0 V;
VTXD = 5 V

[2]

600

IBUS_PAS_rec

receiver recessive input

leakage current

VBAT = 5 V; VLIN = 18 V;
VTXD = 5 V

[2]

IBUS_NO_GND

loss-of-ground bus current VBAT = 18 V; VLIN = 0 V

[2]

750

+10

IBUS_NO_BAT

loss-of-battery bus current VBAT = 0 V; VLIN = 18 V

[2]

VBUSdom

receiver dominant state

[2]

0.4VBAT

VBUSrec

receiver recessive state

[2]

0.6VBAT

VBUS_CNT

receiver center voltage

VHYS

receiver hysteresis voltage VHYS = VBUSrec VBUSdom

VSerDiode

voltage drop at the serial

diode

VO(dom)

dominant output voltage

Rslave

slave resistance

CLIN

capacitance on pin LIN

0.475VBAT 0.5VBAT

0.525VBAT V

[2]

0.175VBAT V

in pull-up path with Rslave;

ISerDiode = 0.9 mA

[2]

0.4

1.0

Normal mode; VTXD = 0 V;

VBAT = 7.0 V

[2]

1.4

Normal mode; VTXD = 0 V;

VBAT = 18 V

[2]

2.0

20

30

60

with respect to GND

[2]

20

pF

[2]

150

200

VBUS_CNT =
(VBUSdom + VBUSrec) / 2

Thermal shutdown
Tj(sd)

shutdown junction
temperature

[1]

All parameters are guaranteed over the virtual junction temperature range by design. Factory testing uses correlated test conditions to
cover the specified temperature and power supply voltage range.

[2]

Not tested in production; guaranteed by design.

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

12 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

11. Dynamic characteristics

Table 8.
Dynamic characteristics
VBAT = 5 V to 18 V; Tvj = 40 C to +150 C; RL(LIN-VBAT) = 500 ; all voltages are referenced to pin GND; positive currents
flow into the IC; typical values are given at VBAT = 12 V, unless otherwise specified.[1]
Symbol

Parameter

Conditions

Min

Typ

Max

duty cycle 1

Vth(rec)(max) = 0.744 VBAT;

Vth(dom)(max) = 0.581 VBAT;
tbit = 50 s; VBAT = 7 V to 18 V

[2][4][5]

0.396 -

Vth(rec)(max) = 0.768 VBAT;

Vth(dom)(max) = 0.6 VBAT;
tbit = 50 s; VBAT = 5 V to 7 V

[2][4][5]

0.396 -

Vth(rec)(min) = 0.422 VBAT;

Vth(dom)(min) = 0.284 VBAT;
tbit = 50 s; VBAT = 7.6 V to 18 V

[3][4][5]

0.581

Vth(rec)(min) = 0.405 VBAT;

Vth(dom)(min) = 0.271 VBAT;
tbit = 50 s; VBAT = 5.6 V to 7.6 V

[3][4][5]

0.581

Vth(rec)(max) = 0.778 VBAT;

Vth(dom)(max) = 0.616 VBAT;
tbit = 96 s; VBAT = 7 V to 18 V

[2][4][5]

0.417 -

Vth(rec)(max) = 0.805 VBAT;

Vth(dom)(max) = 0.637 VBAT;
tbit = 96 s; VBAT = 5 V to 7 V

[2][4][5]

0.417 -

Vth(rec)(min) = 0.389 VBAT;

Vth(dom)(min) = 0.251 VBAT;
tbit = 96 s; VBAT = 7.6 V to 18 V

[3][4][5]

0.590

Vth(rec)(min) = 0.372 VBAT

Vth(dom)(min) = 0.238 VBAT
tbit = 96 s; VBAT = 5.6 V to 7.6 V

[3][4][5]

0.590

Unit

Duty cycles
1

duty cycle 2

duty cycle 3

duty cycle 4

Timing characteristics
trx_pd

receiver propagation
delay

rising and falling;

CRXD = 20 pF; RRXD = 2.4 k

[5]

trx_sym

receiver propagation
delay symmetry

CRXD = 20 pF; RRXD = 2.4 k;

rising edge with respect to falling edge

[5]

+2

twake(dom)LIN

LIN dominant wake-up

time

Sleep mode

30

80

150

tgotonorm

go to normal time

time period for mode change from

Sleep or Standby mode to Normal
mode

10

tinit(norm)

normal mode
initialization time

20

tgotosleep

go to sleep time

10

[1]

[2]

time period for mode change from

Normal to Sleep mode

All parameters are guaranteed over the virtual junction temperature range by design. Factory testing uses correlated test conditions to
cover the specified temperature and power supply voltage ranges.

t bus rec min

1 3 = ------------------------------- . Variable tbus(rec)(min) is illustrated in the LIN timing diagram in Figure 5.
2 t bit

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

13 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

[3]

t bus rec max

2 4 = -------------------------------- . Variable tbus(rec)(max) is illustrated in the LIN timing diagram in Figure 5.
2 t bit

[4]

Bus load conditions: CBUS = 1 nF and RBUS = 1 k; CBUS = 6.8 nF and RBUS = 660 ; CBUS = 10 nF and RBUS = 500 .

[5]

See timing diagram in Figure 5.

tbit

tbit
VTXD

tbus(rec)(min)

tbus(dom)(max)

Vth(rec)(max)

Vth(dom)(max)
VBAT

LIN BUS
signal

thresholds of
receiving node 1

tbus(rec)(max)

tbus(dom)(min)

Vth(rec)(min)

Vth(dom)(min)

trx_pdr

trx_pdf

thresholds of
receiving node 2

trx_pdf

VRXD
receiving
node 1
trx_pdf
receiving
node 2

trx_pdr

trx_pdf

VRXD
015aaa237

Fig 5.

Timing diagram of LIN transceiver duty cycle

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

14 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

12. Application information

12.1 Application diagram
VECU

LIN BUS
LINE

BATTERY

+3 V/
+5 V
only for
master node

VBAT
VDD

RX0

MICROTX0
CONTROLLER
Px.x

GND

RXD

TXD

SLP_N

1 k

TJA1027

LIN
(1)
015aaa238

(1) Master: C = 1 nF; slave: C = 220 pF

Fig 6.

Application diagram

12.2 ESD robustness according to LIN EMC test specification

ESD robustness (IEC 61000-4-2) has been tested by an external test house according to
the LIN EMC test specification (part of Conformance Test Specification Package for
LIN 2.1, October 10th, 2008). The test report is available on request.
Table 9.

ESD robustness (IEC 61000-4-2) according to LIN EMC test specification

Pin

Test configuration

Value

Unit

LIN

no capacitor connected to LIN pin

13

kV

220 pF capacitor connected to LIN pin

12

kV

100 nF capacitor connected to VBAT pin

> 15

kV

VBAT

12.3 Hardware requirements for LIN interfaces in automotive applications

The TJA1027 satisfies the "Hardware Requirements for LIN, CAN and FlexRay Interfaces
in Automotive Applications", Version 1.1, December 2009.

13. Test information

13.1 Quality information
This product has been qualified in accordance with the Automotive Electronics Council
(AEC) standard Q100 Rev-G - Failure mechanism based stress test qualification for
integrated circuits, and is suitable for use in automotive applications.

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

15 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

14. Package outline

SO8: plastic small outline package; 8 leads; body width 3.9 mm

SOT96-1

A
X

c
y

HE

v M A

Z
5

Q
A2

(A 3)

A1
pin 1 index

Lp
1

detail X

w M

bp

2.5

5 mm

scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT

A
max.

A1

A2

A3

bp

D (1)

E (2)

HE

Lp

Z (1)

mm

1.75

0.25
0.10

1.45
1.25

0.25

0.49
0.36

0.25
0.19

5.0
4.8

4.0
3.8

1.27

6.2
5.8

1.05

1.0
0.4

0.7
0.6

0.25

0.25

0.1

0.7
0.3

inches

0.069

0.010 0.057
0.004 0.049

0.01

0.019 0.0100
0.014 0.0075

0.20
0.19

0.16
0.15

0.05

0.01

0.01

0.004

0.028
0.012

0.244
0.039 0.028
0.041
0.228
0.016 0.024

8o
o
0

Notes
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
2. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.

Fig 7.

REFERENCES

OUTLINE
VERSION

IEC

JEDEC

SOT96-1

076E03

MS-012

JEITA

EUROPEAN
PROJECTION

ISSUE DATE
99-12-27
03-02-18

Package outline SOT96-1 (SO8)

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

16 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

HVSON8: plastic thermal enhanced very thin small outline package; no leads;
8 terminals; body 3 x 3 x 0.85 mm

SOT782-1

A1
c

detail X
terminal 1
index area
e1

terminal 1
index area

e
1

C A B
C

v
w

y1 C

L
K

Eh

5
Dh
0

1
scale

Dimensions
Unit(1)
mm

2 mm

A1

max 1.00 0.05 0.35

nom 0.85 0.03 0.30
min 0.80 0.00 0.25

c
0.2

Dh

Eh

e1

3.10 2.45 3.10 1.65

0.35 0.45
3.00 2.40 3.00 1.60 0.65 1.95 0.30 0.40
2.90 2.35 2.90 1.55
0.25 0.35

v
0.1

0.05 0.05

y1
0.1

Note
1. Plastic or metal protrusions of 0.075 maximum per side are not included.

Fig 8.

References

Outline
version

IEC

JEDEC

JEITA

SOT782-1

---

MO-229

---

sot782-1_po

European
projection

Issue date
09-08-25
09-08-28

Package outline SOT782-1 (HVSON8)

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

17 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

15. Handling information

All input and output pins are protected against ElectroStatic Discharge (ESD) under
normal handling. When handling ensure that the appropriate precautions are taken as
described in JESD625-A or equivalent standards.

16. Soldering of SMD packages

This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 Surface mount reflow
soldering description.

16.1 Introduction to soldering

Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.

16.2 Wave and reflow soldering

Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:

Through-hole components
Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:

Board specifications, including the board finish, solder masks and vias
Package footprints, including solder thieves and orientation
The moisture sensitivity level of the packages
Package placement
Inspection and repair
Lead-free soldering versus SnPb soldering

16.3 Wave soldering

Key characteristics in wave soldering are:
TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

18 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave

Solder bath specifications, including temperature and impurities

16.4 Reflow soldering
Key characteristics in reflow soldering are:

Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 9) than a SnPb process, thus
reducing the process window

Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board

Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 10 and 11
Table 10.

SnPb eutectic process (from J-STD-020D)

Package thickness (mm)

Package reflow temperature (C)

Volume (mm3)
< 350

350

< 2.5

235

220

2.5

220

220

Table 11.

Lead-free process (from J-STD-020D)

Package thickness (mm)

Package reflow temperature (C)

Volume (mm3)
< 350

350 to 2000

> 2000

< 1.6

260

260

260

1.6 to 2.5

260

250

245

> 2.5

250

245

245

Moisture sensitivity precautions, as indicated on the packing, must be respected at all

times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 9.

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

19 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

maximum peak temperature

= MSL limit, damage level

temperature

minimum peak temperature

= minimum soldering temperature

peak
temperature

time
001aac844

MSL: Moisture Sensitivity Level

Fig 9.

Temperature profiles for large and small components

For further information on temperature profiles, refer to Application Note AN10365

Surface mount reflow soldering description.

17. Soldering of HVSON packages

Section 16 contains a brief introduction to the techniques most commonly used to solder
Surface Mounted Devices (SMD). A more detailed discussion on soldering HVSON
leadless package ICs can found in the following application notes:

AN10365 Surface mount reflow soldering description

AN10366 HVQFN application information

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

20 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

18. Revision history

Table 12.

Revision history

Document ID

Release date

Data sheet status

Change notice

Supersedes

TJA1027 v.2

20130424

Product data sheet

TJA1027 v.1

Modifications:

TJA1027 v.1

TJA1027

Product data sheet

text in Title, Section 1, Section 2.1, Section 7.1 revised to include LIN 2.2A compliance
text in Section 7.1 revised to be consistent with TJA1029
Figure 2: revised/resized
Table 3, Table note 1: revised
Figure 4: revised
Table 7: revised measurement conditions for parameter IBUS_NO_BAT
Section 13.1: text revised
20111020

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

21 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

19. Legal information

19.1 Data sheet status
Document status[1][2]

Product status[3]

Definition

Objective [short] data sheet

Development

This document contains data from the objective specification for product development.

Preliminary [short] data sheet

Qualification

This document contains data from the preliminary specification.

Product [short] data sheet

Production

This document contains the product specification.

[1]

Please consult the most recently issued document before initiating or completing a design.

[2]

The term short data sheet is explained in section Definitions.

[3]

The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.

19.2 Definitions
Draft The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.

19.3 Disclaimers
Limited warranty and liability Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.

TJA1027

Product data sheet

Suitability for use in automotive applications This NXP

Semiconductors product has been qualified for use in automotive
applications. Unless otherwise agreed in writing, the product is not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer's own
risk.
Applications Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customers sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customers applications and
products planned, as well as for the planned application and use of
customers third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customers applications or products, or the application or use by customers
third party customer(s). Customer is responsible for doing all necessary
testing for the customers applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customers third party
customer(s). NXP does not accept any liability in this respect.
Limiting values Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customers general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

22 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

No offer to sell or license Nothing in this document may be interpreted or

construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.

Quick reference data The Quick reference data is an extract of the

product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.

Export control This document as well as the item(s) described herein

may be subject to export control regulations. Export might require a prior
authorization from competent authorities.

19.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.

20. Contact information

For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]

TJA1027

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 2 24 April 2013

NXP B.V. 2013. All rights reserved.

23 of 24

TJA1027

NXP Semiconductors

LIN 2.2A/SAE J2602 transceiver

21. Contents
1
2
2.1
2.2
3
4
5
6
6.1
6.2
7
7.1
7.2
7.2.1
7.2.2
7.2.3
7.2.4
7.3
7.3.1
7.3.2
7.4
7.5
7.6
8
9
10
11
12
12.1
12.2
12.3
13
13.1
14
15
16
16.1
16.2
16.3
16.4
17

General description . . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Quick reference data . . . . . . . . . . . . . . . . . . . . . 2
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pinning information . . . . . . . . . . . . . . . . . . . . . . 4
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
Functional description . . . . . . . . . . . . . . . . . . . 5
LIN 2.x/SAE J2602 compliant . . . . . . . . . . . . . . 5
Operating modes . . . . . . . . . . . . . . . . . . . . . . . 5
Reset mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Standby mode. . . . . . . . . . . . . . . . . . . . . . . . . . 7
Normal mode . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Transceiver wake-up . . . . . . . . . . . . . . . . . . . . 8
Remote wake-up via the LIN bus . . . . . . . . . . . 8
Wake-up via pin SLP_N . . . . . . . . . . . . . . . . . . 8
Operation during automotive cranking pulses . 8
Operation when supply voltage is outside
specified operating range . . . . . . . . . . . . . . . . . 8
Fail-safe features . . . . . . . . . . . . . . . . . . . . . . . 9
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 10
Thermal characteristics . . . . . . . . . . . . . . . . . 10
Static characteristics. . . . . . . . . . . . . . . . . . . . 11
Dynamic characteristics . . . . . . . . . . . . . . . . . 13
Application information. . . . . . . . . . . . . . . . . . 15
Application diagram . . . . . . . . . . . . . . . . . . . . 15
ESD robustness according to LIN EMC test
specification . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Hardware requirements for LIN interfaces in
automotive applications . . . . . . . . . . . . . . . . . 15
Test information . . . . . . . . . . . . . . . . . . . . . . . . 15
Quality information . . . . . . . . . . . . . . . . . . . . . 15
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 16
Handling information. . . . . . . . . . . . . . . . . . . . 18
Soldering of SMD packages . . . . . . . . . . . . . . 18
Introduction to soldering . . . . . . . . . . . . . . . . . 18
Wave and reflow soldering . . . . . . . . . . . . . . . 18
Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 18
Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 19
Soldering of HVSON packages. . . . . . . . . . . . 20

18
19
19.1
19.2
19.3
19.4
20
21

Revision history . . . . . . . . . . . . . . . . . . . . . . .
Legal information . . . . . . . . . . . . . . . . . . . . . .
Data sheet status . . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact information . . . . . . . . . . . . . . . . . . . .
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21
22
22
22
22
23
23
24

Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section Legal information.

NXP B.V. 2013.

All rights reserved.

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: [email protected]
Date of release: 24 April 2013
Document identifier: TJA1027