Intensification Ratio

SM
Solutions
Intensification Ratio (Ri)

What is it?
And How to Calculate
By John Bozzelli
In all hydraulic injection-molding machines, hydraulic power is converted, multiplied or intensified, into
plastic pressure (melt pressure in the nozzle). The law of physics involved is F = P x A. That is force (F)
is equal to pressure (P) times area (A). The large hydraulic piston pushes the screw where the non-return
valve or check valve acts as a plunger pushing plastic through the nozzle into the mold. The hydraulic
piston has a large surface area, for example 100 cm2. The non-return valve during injection forward acts
like a smaller area piston, for example 10 cm2. This large to small ratio of ram areas causes the hydraulic
pressure to be intensified to plastic pressure in the nozzle of the injection barrel. In this specific case
hydraulic pressure is intensified or multiplied by a factor of 10. This is the machine's intensification
ratio and explains how hydraulic pressure can provide tens of thousands of psi plastic-pressure inside the
nozzle. That is, 800 psi of hydraulic pressure provides ~8,000 psi of melt pressure inside the nozzle.
Today you can buy machines with intensification ratios ranging from 6:1 to 43:1. Custom machines can
be even larger. Most machines are NOT 10:1. It is plastic pressure that pushes plastic into the sprue,
runner, gate and mold cavity, NOT hydraulic pressure. This plastic pressure must be duplicated as you
go from to machine to machine with the same mold. If your plant has different size or makes of
machines, most likely they have different intensification ratios. That is 800-psi pack and hold pressure on
one machine with an intensification of 10:1 develops 8,000-psi plastic pressure in the nozzle, but on
another machine with a different intensification ratio of 12.75:1; 800-psi hydraulic pressure develops
10,200-psi plastic packing pressure in the nozzle. You will not make the same part. To make the same
part you must pack out the cavity with the same cavity pressure. See Figure 1 for an illustration.
How to Calculate:
Ideally, you should find the screw diameter and the functional hydraulic ram diameter to calculate the
ratio of areas. Unfortunately, you would spend hours looking for the hydraulic ram area and in some
cases, it cannot be found in the machine manuals. While this is the best way, it is not practical. An easier
method is to find the machine specifications, identify which diameter screw you have in the machine and
from the machine specifications find the maximum plastic or melt pressure the machine can develop.
Then go to the machine and find what the maximum hydraulic pressure you are allowed to set for
injection or first stage. Once you have these two numbers you can calculate the machines intensification
number with the following equation
Ri = Maximum injection (plastic) pressure/maximum hydraulic pressure for the injection unit.
Injection Molding Solutions 1019 Balfour St. Midland, MI 48640 Ph: 989.832.2424 Fax: 989.832.8743
Email: [email protected]; Web site: www.ScientificMolding.com
SM
Solutions
Example:
From machine specifications, we find that for the maximum injection or plastic pressure possible is
26,500 psi. From the machine controller we find that the maximum hydraulic pressure we can set the
injection cylinder to is 2,250 psi
Ri = 26,500 psi/2,250 psi = 11.78:1.

To calculate the plastic pressure for backpressure during screw run with a machine setting of 75 psi
hydraulic, multiply the hydraulic pressure times the intensification ratio. In this case:
Ri = 75 psi x 11.78 = 883 psi

If you transferred this process to an electric machine, you would have to set 883 psi on input for
backpressure.
Figure 1: Intensification Ratio Diagram:
Hydraulic vs Plastic Pressure

Area of Non-Return
Valve is 1 in2
Area of ram
is 10 in2
Intensification Ratio is 10:1

Pump
Injection Molding Solutions 1019 Balfour St. Midland, MI 48640 Ph: 989.832.2424 Fax: 989.832.8743
Email: [email protected]; Web site: www.ScientificMolding.com

Intensification Ratio

Uploaded by

Copyright:

Available Formats

Intensification Ratio

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Intensification Ratio

Uploaded by

Copyright:

Available Formats

SM

Intensification Ratio (Ri)

Ri = 26,500 psi/2,250 psi = 11.78:1.

Ri = 75 psi x 11.78 = 883 psi

Figure 1: Intensification Ratio Diagram:

Hydraulic vs Plastic Pressure

Intensification Ratio is 10:1

You might also like