Scribd
Upload
1K views2 pages

How To Configure RIP v2 Step by Step

RIP version 2 is configured on three routers by entering global configuration mode, enabling RIP, setting the version to 2, and advertising the connected networks. The routing tables are checked before and after configuration using the show ip route command.

Uploaded by

madham1985
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
1K views2 pages

How To Configure RIP v2 Step by Step

RIP version 2 is configured on three routers by entering global configuration mode, enabling RIP, setting the version to 2, and advertising the connected networks. The routing tables are checked before and after configuration using the show ip route command.

Uploaded by

madham1985
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 2

How to configure RIP v2 step by step?

RIP short for "Routing Information Protocol" is a routing protocol used to select the suitable route
for packets with in network. RIP basically an open standard dynamic routing protocol and not relate
to any particular vendor.

The latest version of RIP is RIP version 2 with some new features, for example RIP v2 is class less
protocol that sends subnet mask information with routing updates and support VLSM (variable
length subnet masking also).

 From the global configuration mode, configure the hostname then configure the console and enable
passwords on each router.

To configure RIP v2, first enter global configuration mode to run the following commands. 

Configure the routing protocol on Router A. 

First run the command show ip route to view the IP routing table for router A before RIP v2. 

RouterA(config)#configure terminal                (enter in global configuration mode) 

RouterA(config)#router rip                              (enable RIP)

RouterA(config-router)#version 2                                (enable RIP v2) 

RouterA(config-router)#network 10.0.0.0       (advertise the network 10.0.0.0)

RouterA(config-router)#network 20.0.0.0       (advertise the network 20.0.0.0)

RouterA(config-router)#network 193.168.1.0 (advertise the network 193.168.1.0)

RouterA(config-router)#exit

RouterA(config)#

  
Configure the routing protocol on Router B. 

First run the command show ip route to view the IP routing table for router B before RIP v2. 

RouterB(config)#configure terminal                (enter in global configuration mode) 

RouterB(config)#router rip                              (enable RIP)

RouterB(config-router)#version 2                                (enable RIP v2) 

RouterB(config-router)#network 10.0.0.0       (advertise the network 10.0.0.0)

RouterB(config-router)#network 15.0.0.0       (advertise the network 15.0.0.0)

RouterB(config-router)#network 193.168.2.0 (advertise the network 193.168.2.0)

RouterB(config-router)#exit

RouterB(config)#

   

Configure the routing protocol on Router C. 

First run the command show ip route to view the IP routing table for router C before RIP v2. 

RouterC(config)#configure terminal                (enter in global configuration mode) 

RouterC(config)#router rip                              (enable RIP)

RouterC(config-router)#version 2                                (enable RIP v2) 

RouterC(config-router)#network 20.0.0.0       (advertise the network 20.0.0.0)

RouterC(config-router)#network 15.0.0.0       (advertise the network 15.0.0.0)

RouterC(config-router)#network 193.168.3.0 (advertise the network 193.168.3.0)

RouterC(config-router)#exit

RouterC(config)#

From the enable mode, examine the routing table entries using the show ip route command on each
router.

You might also like