Applications

Mechanical Seals

Sealing Systems
according to API 682, 3rd Edition
and ISO 21049, 1st Edition.
Classification and Seal Selection.

58 E

Your partner for sealing technology worldwide

Table of Contents
Foreword

Classification of Sealing Systems

Classification of sealing systems - general notes
Categories, arrangements and seal types - overview chart
Seal configurations and flush plans

4
5 *)
6

Seal Selection
How to select the correct EagleBurgmann sealing system
Seal selection by seal features
Seal selection by media groups

10
11 *)
12

Pusher seals (Type A)

Metal bellows seals (Type B and C)
Gas seals (Type A)
Containment seals (Type A)

13
14
15
16

API plans - overview

Basic API plans
Flush systems
Quench and buffer systems
Barrier systems
Leakage alarm and collection systems

17
18
20
21
22
24

Appendix
EagleBurgmann API 682 tools
Selection of buffer and barrier fluids
Seal coding system
Objectives and category details

26
27
27
28 *)

EagleBurgmann in profile

29
EagleBurgmann
SHV-D

*) Fold-out pages

EagleBurgmann
HRGS

Burgmann is a Trade Mark of EagleBurgmann

Photo at front page: Statoil

Gas oil pump (Ruhrpumpen) with

EagleBurgmann mechanical seal
type MFLWT80/95-TA3 and supply
system SPA 3020. Temperature
285 C ... 310 C, pressure 5 bar.

Foreword
This brochure provides basic information about ISO 21049 and API 682. It contains
a set of checklists and summaries which give a brief overview that will help to
select suitable EagleBurgmann sealing systems. ISO 21049 is an international
standard which is based on API 682 (a standard of the American Petroleum Institute). The content of these two standards is generally identical.
Both standards specify requirements and recommendations for the selection and
operation of shaft sealing systems in new or retrofitted centrifugal and rotary
pumps. They refer to pumps which are mainly used for hazardous, flammable and/
or toxic applications in the petroleum, natural gas and chemical industries.
The improvement of equipment reliability and the reduction of emissions and lifecycle costs are the major targets of these standards.
The following table summarizes the history of API 682/ ISO 21049 and the pump
standards API 610/ ISO 13709:

Year

Pump specification

Mechanical seal specification

Note

2004

API 610, 10th edition

API 682, 3rd edition

Same wording and structure as in the ISO documents

ISO 21049

Enhancements to API 682, 2nd edition

2003

ISO 13709

Enhancements to API 610, 9th edition

2002

API 610, 9th edition

API 682, 2nd edition

Seal chambers in API 610, new seal coding system in API 682

1996

API 610, 8th edition

References API 682 1st edition

1995

API 682, 1st edition

1990

API 610, 7th edition

First stand alone API seal standard

Revised seal coding system
The API 682 task force of the American Petroleum Institute is the author of
- 682. ISO 21049 has been created
Contains
sealcommittees
specificationISO/TC 115,
API
by the basic
technical
Defines seal coding system
SC3 and ISO/TC 67, SC6.
The checklists, summaries and API plans are based on both standards. For further
and more detailed information please refer to the commercially available documents of API 682 3rd edition and ISO 21049.

EagleBurgmann
CGSH

Classification of Sealing Systems

API 682 and ISO 21049 specify a range of different sealing systems. Parameters such as category, arrangement, configuration, type and API plans are to be
considered.
The chart overleaf is a quick overview about the basic features of the different
categories, arrangements and seal types. It also shows the links between these
parameters and marks default and optional selections.
Step I: The category determines the applicable seal chamber, basic seal design
features, maximum operating conditions, testing and data requirements. Each
category has special demands regarding the seal arrangement, configuration and
type. There are three different categories.
Step II: Determines the arrangement of the mechanical seal cartridges and their
possible configurations.
The configuration determines the sealing method, orientation of the mechanical
seal components, the use of containment seals and the required API plans. API 682
and ISO 21049 specify six default configurations and five optional configurations.
Each of these configurations can be realized with different seal types.

EagleBurgmann MFLWT80.
The universal primary
seal for both hot
and cold
applications
in refineries.

Step Ill: Definition of the seal type, the design and material of the spring element
and the secondary seals.
It defines the appropriate operating limits. API 682 and ISO 21049 specify three
basic seal types, a fourth option is a totally engineered sealing system (ES).
Step IV: Completes the sealing system classification by selecting the required
API plan.
API 682 and ISO 21049 introduce a seal code which contains
information about the category, arrangement, type and API plan.
For further details please refer to page 27.

EagleBurgmann mechanical seal type

MFLWT80S3/90-TA1 and supply system SPA
3020/A22 according to API plan 54 + 02 in
residue pumps (Byron Jackson).
Temperature 332 C, pressure 8.5 bar.

Residue pumps (Ruhrpumpen) with

EagleBurgmann MFLW80-D1/70 and
SPA3020/A22. Operation according
to API plan 54 + 02. Temperature
375 C, pressure 3 bar.

Categories, Arrangements and Seal Types

Step I Category (see page 28)
Category 1

Category 2

Category 3

ISO 3069 type C, ASME B73.1, ASME B73.2

ISO 13709 / API 610 10th edition

-40 C 260 C, 21 bar g (-40 F 500 F, 300 PSI)

-40 C 400 C, 41 bar g (-40 F 750 F, 600 PSI)

Minimal data requirements

Rigorous data requirements

Step II Arrangement and configuration

Step III Type and spring position

Arrangement 1

1CW-FX

Type A

Rotary springs

Single seal cartridge

Contacting Wet - FiXed throttle bushing

Category 1: carbon throttle bushing
Category 2: non-sparking metal throttle
bushing
Category 3: not applicable

Pusher seal
Temperature: -40 to 176 C (-40 to 350 F)
Pressure:
41 bar g (600 PSI)
Multiple springs: Alloy C-276
Single spring: SS 316
O-rings:
FKM or FFKM

NBR, HNBR, EPM, EPDM, TFE

Seal face surface

speed < 23 m/s

Type B

Rotary bellows

1CW-FL
Contacting Wet - FLoating throttle bushing
Category 3: carbon throttle bushing
Category 1 and 2: carbon throttle bushing
Arrangement 2

2CW-CW

Dual seal cartridge

- pressure between seals
less than seal chamber
pressure
- internal reverse balance
feature
- fixed carbon throttle
bushing

Contacting Wet - Contacting Wet

2CW-CS
Contacting Wet - Containment Seal
(non-contacting or contacting CS)

Type C

Stationary springs
Seal face surface
speed > 23 m/s

Stationary bellows

Rotary bellows

Arrangement 3

3CW-FB

Metal bellows seal with flexible graphite

Temperature: -40 to 400 C (-40 to 750 F)
Pressure:
21 bar g (300 PSI)
Metal bellows: Alloy 718
Sealing element: flexible graphite

Dual seal cartridge

- pressure between seals
higher than seal
chamber pressure
- internal reverse balance
feature
- fixed carbon throttle
bushing

Contacting Wet - Face-to-Back

Totally Engineered Sealing system (ES)

3CW-BB

For service conditions outside the operating limits of type A, B and C

Temperature: < -40 or > 260 C (< -40 or > 500 F) category 1

< -40 or > 400 C (< -40 or > 750 F) category 2 and 3
Pressure:
> 21 bar g (300 PSI) category 1

> 41 bar g (600 PSI) category 2 and 3
Surface speed: > 23 m/s (75 ft/s)
Shaft diameter: below 20 mm (0.75 inch) or above 110 mm (4.3 inch)
Medium:
highly corrosive fluids for which the specified materials in
API 682/ISO 21049 are not suitable, fluids with absolute
vapour pressures > 34 bar a (493 PSI), unstable liquid
properties (e.g. multiphase, non-Newtonian), high viscosity
or pour point above or within 20C (68 F) of the minimum ambient temperature.

2NC-CS
Non-Contacting - Containment Seal
(non-contacting or contacting CS)

Contacting Wet - Back-to-Back

3CW-FF
Contacting Wet - Face-to-Face
3NC-BB
Non-Contacting - Back-to-Back
3NC-FF
Non-Contacting - Face-to-Face
3NC-FB
Non-Contacting - Face-to-Back

Default configurations
Optional configurations
Optional design feature

Metal bellows seal with O-rings

Temperature: -40 to 176 C (-40 to 350 F)
Pressure:
21 bar g (300 PSI)
Metal bellows: Alloy C-276
O-rings:
FKM or FFKM

NBR, HNBR, EPM, EPDM, TFE

Flexible element

Stationary bellows

Arrangement 1 Single Seal Configurations and API Plans

Process side

Atmospheric side

1cw-fx MFL85N

1CW-FX

Plan 11
Recirculation from
discharge to seal
chamber

Contacting Wet - FiXed throttle bushing

Example: MFL85N (type B)

F

Plan 61
Plugged connections

plugged

1cw-fl H75VN
Plan 13
Recirculation from seal
chamber to suction

Werb-Nr. 2841

1CW-FL

Plan 62
External quench

Quench

Contacting Wet - FLoating throttle bushing

F

D Q

drain

Plan 23
Internal recirculation
through a cooler

TI

Each configuration is available for seal types A, B and C

Plan 65
Leakage control by float
type level switch

Werb-Nr. 2787

Plan 31
Recirculation from
discharge through a
cyclone separator to
seal chamber

LSH

EagleBurgmann
H75
Plan 32
External flush
into the seal
chamber

Option

EB

drain

Client
FI

PI
TI

Default configurations
Optional configurations

Arrangement 2 Dual Seal Configurations and API Plans

Pressure between seals less than seal chamber pressure
2cw-cw H75VK-PTA

Process side

Between seals
2CW-CW

Plan 11
Recirculation from
discharge to seal
chamber

Contacting Wet Contacting Wet

Example: H75VK-H75P (type A)
LBO

are

Plan 52
Unpressurized
buffer fluid system

PI

LBI

lling

PSH

LSH
LI

if specied

LSL

2cw-cs H75VK+CGSH
Plan 13
Recirculation from seal
chamber to suction

Werb-Nr. 2790

2CW-CS

Contacting Wet Containment Seal

EB

Client

Example: H75VK-CGSH (type A)

if specied
FE

FSH

PSL

PI

Plan 32
External flush
into the
seal chamber

Option

EB

PCV

F
I
L

Client
FI

Plan 72
Buffer gas system

PI
TI

Each configuration is available for seal types A, B and C

Plan 75
Condensate recovery for
condensing leakage

Werb-Nr. 2789
2nc-cs CGSH-CGSH

are
PI
PSH

LI

LSH
if specied

Plan 14
Recirculation from seal chamber
to suction and circulation from
discharge to seal chamber

2NC-CS

Non-Contacting Containment Seal

Example: CGSH-CGSH (type A)

drain

Plan 76
Vapour recovery system for noncondensing leakage

are

PSH

PI

drain

Werb-Nr. 2791

Default configurations
Optional configurations

Arrangement 3 Dual Seal Configurations and API Plans

Barrier fluid pressure higher than seal chamber pressure
3cw-fb H75VK-PTA

Process side

Between seals
3CW-FB

Plan 02
Dead end (plugged connections)

Contacting Wet Face-to-Back

Example: H75VK-H75P (type A)

N2

Plan 53A
Barrier fluid reservoir

PSL

PI
lling

LSH
LI

if specied

LSL

3cw-bb H75VKP-D
WS\NNLK

Plan 11
Recirculation from
discharge to seal
chamber

3CW-BB

Contacting Wet Back-to-Back

Example: H75VKP-D (type A)

Werb-Nr. 2793

Plan 53B
Barrier fluid bladder
accumulator system

vent
PI

PSL

lling

3cw-ff SH

TI
if specied

Plan 13
Recirculation from seal
chamber to suction

3CW-FF

Contacting Wet Face-to-Face

Example: SHVP-D (type A or engineered seal ES)

Werb-Nr. 2792

Plan 53C
Barrier fluid piston
accumulator system

79=
]LU[
70

30

7:3

3:3
MPSSPUN

;0
PMZWLJPMPLK

Plan 14
Recirculation from seal chamber
to suction and circulation from
discharge to seal chamber

EagleBurgmann
SHV-D

Werb-Nr. 2794

Plan 54
External barrier fluid
system

L_[LYUHS
ZV\YJL

Each configuration is available for seal

types A, B and C

Default configurations
Optional configurations

Arrangement 3 Dual Seal Configurations and API Plans

Barrier gas pressure higher than seal chamber pressure
3nc-bb CGSH-KD

Process side

Between seals
3NC-BB

Plan 02
Dead end (plugged connections)

Non-Contacting Back-to-Back

Example: CGSH-KD (type A)

Plan 74
Pressurized barrier gas

EB

3nc-ff RGS-D

if specied
FE

FSH
PSL

WS\NNLK

Client

PCV

F
I
L

PI

3NC-FF

Non-Contacting Face-to-Face

Example: RGS-D (type A)

Werb-Nr. 2795

3nc-fb HRGS-DD

3NC-FB

Non-Contacting Face-to-Back
Werb-Nr. 2797

Example: HRGS-DD (type A)

Werb-Nr. 2796

EagleBurgmann CGSH
seal face

Default configurations
Optional configurations

How to select the correct EagleBurgmann Sealing System

This chapter is dedicated to find the correct EagleBurgmann Sealing System
according to API 682 / ISO 21049 standard.
Before beginning with the seal selection, some general information:
) and options (
) for several
API 682 and ISO 21049 specify defaults (
design details and the selection of the seal materials. The options are only
permitted with the approval of the customer. Therefore typical seal codes always
assume all standard defaults.
The standards do not intend to prevent a vendor from offering or the customer from
requesting alternative equipment or engineered products for special applications.
This may be particulary appropriate where there are options, innovative or developing
designs or materials. Further information shall be provided by the vendor if an option
or any variations to this standard are offered.
How to select the EagleBurgmann sealing system
The tables on page 11 and 12 describe two different ways to select the
EagleBurgmann seal needed for a specific API-application.

EagleBurgmann mechanical
seal MFLW85S20/75-TA1
used in pumps
(Ruhrpumpen) to seal gas oil
with sulphur. Temperature
217C, pressure 2.3 bar.

Seal selection by seal features

The table on page 11 is used after the arrangement, configuration and seal type is
defined. The table is structured in the same way as the APIscheme on page 5.
Going from left to right, the same three steps have to be made as described on
page 4: by choosing the arrangement, configuration and type required. In the
column Flexible Element you can see if rotary or stationary is the default
or option. The Mechanical Seal column on the right lists the recommended
EagleBurgmann seal type. Further down the page tables for some optional
configurations, recommended API plans and a range of EagleBurgmann Supply
Systems can be found.
Seal selection by media groups
API 682 and ISO 21049 define different media groups and typical service
conditions. The tables on page 12 list EagleBurgmann recommendations for
suitable sealing systems. Some of them include optional configurations. Specific
applications may allow or require other seal arrangements and different API plans.
Please contact us for further information.
In the upper table the seal selection for standard seal types can be found. The table
below is dedicated to optional seals.

10

Sealing systems selection by seal features

Arrangement

Default configuration

1CW-FX
1

Single seal
cartridge
1CW-FL

Dual seal
cartridge
2

Operated with
unpressurized buffer
medium
2CW-CS
(tandem)

Dual seal
cartridge
3

2CW-CW
(tandem)

Operated with
pressurized barrier
medium

3CW-FB
(tandem)

3NC-BB

Type Flexible element

Contacting Wet seal

with a FiXed throttle bushing
applicable API plans (process side):
01, 02, 11, 12, 13, 14, 21, 23, 31, 32, 41
applicable API plans (atmospheric side):
51 / 61, 62, 65
Contacting Wet seal
with a FLoating throttle bushing
applicable API plans (process side):
01, 02, 11, 12, 13, 14, 21, 23, 31, 32, 41
applicable API plans (atmospheric side):
51 / 61, 62, 65
Contacting Wet seals
applicable API plans (process side):
01, 02, 11, 12, 13, 14, 21, 23, 31, 32, 41
applicable API plans (between seals):
51, 52
Contacting Wet inner seal
with a Containment Seal
applicable API plans (process side):
01, 02, 11, 12, 13, 14, 21, 23, 31, 32, 41
applicable API plans (between seals):
71, 72, 75, 76
Contacting Wet seals
in Face-to-Back arrangement
applicable API plans (process side):
01, 02, 11, 12, 13, 14, 32
applicable API plans (between seals):
53A, 53B, 53C, 54
Non-Contacting seals
in Back-to-Back arrangement
applicable API plans (process side):
01, 02, 11, 12, 13, 14, 32
applicable API plans (between seals): 74

A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C

Example: Seal selection by seal features: see table above, Arrangement 1 4 1CW-FL 4 Type A 4
Arrangement

Most common optional configurations

See above

See above

2NC-CS (tandem) Non-Contacting inner seal with a Containment Seal A

3CW-BB
Contacting Wet seals in Back-to-Back arrangement A
3NC-FB (tandem) Non-Contacting seals in Face-to-Back arrangement A

EagleBurgmann
mechanical seals
H75VN
SH
MFL85N

MFLWT80
MFL65
H75VN
SH
MFL85N

MFLWT80
MFL65
H75VK / H75P
SH / SHP
MFL85 / MFL85P

MFLWT80 / MFL85P
MFL65 / MFL85P
H75VK / CGSH (EagleEM300)
SH / CGSH (EagleEM300)
MFL85 / CGSH (EagleEM300)

MFLWT80 / CGSH (EagleEM300)

MFL65 / CGSH (EagleEM300)
H75VK / H75P
SH / SHP
MFL90 / MFL85P

MFLWT90 / MFL85P
MFL65 / MFL85P
CGSH-KD
HRGS-DC

Rotary springs
Stationary springs
Rotary bellows
Stationary bellows
Rotary bellows
Stationary bellows
Rotary springs
Stationary springs
Rotary bellows
Stationary bellows
Rotary bellows
Stationary bellows
Rotary springs
Stationary springs
Rotary bellows
Stationary bellows
Rotary bellows
Stationary bellows
Rotary springs
Stationary springs
Rotary bellows
Stationary bellows
Rotary bellows
Stationary bellows
Rotary springs
Stationary springs
Rotary bellows
Stationary bellows
Rotary bellows
Stationary bellows
Rotary springs
Stationary springs
Rotary bellows
Stationary bellows
On request
Rotary bellows
Stationary bellows
Rotary springs 4 H75VN

Type Flexible element

Rotary springs
Rotary springs
Stationary springs

EagleBurgmann
mechanical seals
CGSH / CGSH
H75VKP-D
HRGS-DD

Default configurations
Optional configurations

11

Operation mode API plan

21/22
23
Primary flush
31 (41)
32
51
52
Quench/buffer
systems
62
72
53A
53B
Barrier systems
53C
54
74
65
Leakage
75
collection/alarm
76

Description
Circulation from pump discharge through cooler to seal
Circulation of liquid from seal chamber through cooler to seal
Circulation from discharge through cyclone separator to seal
Injection of clean liquid into seal chamber
External reservoir provides static liquid quench
External reservoir provides circulation buffer liquid
External source provides flowing quench liquid
Gas buffer system
Barrier liquid system with reservoir
Barrier liquid system with bladder accumulator
Barrier liquid system with fluid piston accumulator
Barrier liquid system from external source
Barrier gas system
Recovery system with level control for liquid leakage
Recovery system for condensing leakage
Recovery system for non-condensing leakage

EagleBurgman supply system

WE, WEL
WE, WEL
ZY, (ZY + WE / WEL)
SP24
QFT
TS
SP24
GSS
TS
SPO
SPO
SPA
GSS
LS
LS
SP23

Seal Selection by Media Groups

Standard seal type

< 80 (180)
> 80 (180)

Sour water
Caustic, amines, crystallize

Non-flashing hydrocarbons

H2SO4 (max. 20% at 25C)

H3P04 (max. 20% at 80C)
All other acids

Absolute vapour pressure

less than 1 bar
at pumping temperature

Flashing hydrocarbons

Non-hydrocarbons

Water

Temperature C Pressure
(F)
bar g (PSI)

Absolute vapour pressure

above 1 bar
at pumping temperature

< 80 (180)

< 21 (300)
21 41 (300 600)
< 41 (600)
< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)

Mechanical seal
Type

< 21 (300)
-40 -5
(-40 20)
-5 176
(20 350)
176 260
(350 500)
260 400
(500 750)
-40 -5
(-40 20)
-5 176
(20 350)
176 260
(350 500)
260 400
(500 750)

< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)

ES

Arr.1)

EagleBurgmann
recommendation1)

API plan2)

EagleBurgmann
recommendation2)

H75VN

11

H75VP

23

WE

H75VK / H75P

52

TS

H75VN

62

SP24

H75VK / H75P

53A

TS

Engineered seal

note 3)
53A
53B or C
53A
53B or C
02+53A
02+53C
02+53A
02+53C
53A
53B or C
53A
53B or C
02+53A
02+53C
02+53A
02+53C

TS
SPO
TS
SPO
TS
SPO
TS
SPO
TS
SPO
TS
SPO
TS
SPO
TS
SPO

A
C
ES
C
ES

H75VK / H75P
3

A
C
ES
C
ES

Supply system

MFLWT90 / MFL85P
MFLWT90 / H75P
MFLWT90 / MFL85P
MFLWT90 / H75P
H75VK / H75P

MFLWT90 / MFL85P
MFLWT90 / H75P
MFLWT90 / MFL85P
MFLWT90 / H75P

Example: Seal selection by medium: see table above Non-hydrocarbon 4 Water 4 < 80 C 4 21 bar (g) 4 Type A 4 Arrangement 1 4 H75VN Plan
11
Optional seal type
when specified

Flashing hydrocarbons

Non-flashing hydrocarbons

Non-hydrocarbons

Water

12

Temperature C Pressure
(F)
bar g (PSI)
< 80 (180)
> 80 (180)

Sour water
Caustic, amines, crystallize
H2SO4 (max. 20% at 25 C)
H3P04 (max. 20% at 80 C)
All other acids

< 80 (180)

-40 -5
(-40 20)
Absolute vapour pressure
less than 1 bar
at pumping temperature

Absolute vapour pressure

above 1 bar
at pumping temperature

-5 176
(20 350)
176 260
(350 500)
260 400
(500 750)
-40 -5
(-40 20)
-5 176
(20 350)
176 260
(350 500)
260 400
(500 750)

Mechanical seal

Supply system

Type

API plan2)

EagleBurgmann
recommendation2)

11

Arr.1)

B or C

EagleBurgmann
recommendation1)
MFL85N or MFL65

ES

SHV

B or C
ES
B or C
ES

1
1
1
1

< 21 (300)

B or C

< 21 (300)

ES

B or C

MFL85N or MFL65
SHV
MFL85N or MFL65
SHV
MFL90 / MFL85P
or MFL65 / MFL85P
Engineered seal
MFL90 / MFL85P or
MFL65 / MFL85P
SHPV-D
MFL90 / MFL85P
or MFL65 / MFL85P
SHPV-D

< 21 (300)
21 41 (300 600)
< 41 (600)
< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)

21 41 (300 600)
< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)
< 21 (300)
21 41 (300 600)

1) A specific application may allow another seal arrangement. Please contact EagleBurgmann for further information.
2) A specific application may allow additional or different API plans. Please contact EagleBurgmann for further information.
3) The EagleBurgmann seal type and the API plan(s) are dependant on the specific operation conditions.

ES

B or C

ES
ES

ES

3
3

Engineered seal

SHPV-D
ES

MFL65 / MFL85P
MFL65 / SHPV
MFL65 / MFL85P
MFL65 / SHPV

32
62
53A

SP24
TS

note 3)
53A

TS

53B

SPO

02+53A

TS

53B

SPO

note 3)
53A
53C
02+53A
02+53C
02+53A
02+53C
02+53A
02+53C

TS
SPO
TS
SPO
TS
SPO
TS
SPO

H75VN

Pusher Seals Type A

Operating limits
p1(max) = 41 bar g (600 PSI)
t1 = -40176 C (-40 350 F)
vg(max) = 23 m/s (75 ft/s)

H75VN

H75VP
Materials*)

Face: Carbon (A), SiC (Q1, Q2)

Seat: SiC (Q1, Q2)
O-rings: FKM, FFKM, EPDM, NBR, HNBR
Springs: Alloy C-276**)
Other parts: SS316 (1.4571)
With pumping ring.

H75VP

H75VK

Operating limits and materials*)

see H75VN

Werb-Nr. 2801

With reverse pressure feature.

H75VK

Operating limits and materials*)

see H75VN

Werb-Nr. 2802
SH

With reverse pressure feature, stationary springs.

SHV

Werb-Nr.

Operating limits
p1 (max) = 41150 bar g (6002,115 PSI)
t1 = -40176 C (-40350 F)
vg(max) = 5060 m/s (164229 ft/s)
2800

Materials*)
Face: Carbon (A), SiC (Q1, Q2), Seat: SiC (Q1, Q2)
O-rings: FKM, FFKM, EPDM, NBR, HNBR
Springs: Alloy C-276**)
Other parts: SS316 (1.4571)
Operating limits refer to default seal face combination Carbon/SIC
*) Default

and optional materials available.

Werb-Nr. 2809
**) in C-4 available, EagleBurgmann recommendation.

EagleBurgmann
H75

13

MFL85N

Metal Bellows Seals Type B and C

MFL85N for arrangement 1 and 2 (external pressurization)
MFL90N for arrangement 3 (internal pressurization)

MFL85N/90N

Operating limits
p1 (max) = 25 bar g / 23 bar g (363 PSI / 334 PSI)
t1 = -40176 C (-40350 F)
MFL85P
vg(max) = 23 m/s (75 ft/s)
Materials*)
Face: Carbon (A), SiC (Q1, Q2), Seat: SiC (Q1, Q2)
O-rings: FKM, FFKM, EPDM, NBR, HNBR, Other parts: SS316 (1.4571)
Bellows: Alloy C-276 (in Alloy 718 available, EagleBurgmann recommendation)
MFL85P

With pumping ring.

Operating limits and materials*)
see MFL85/90N
MFL65

Werb-Nr. 2806

With stationary bellows.

MFL65

Operating limits
p1 (max) = 25 bar g (363 PSI)
t1 = -40400 C (-40750 F)
vg(max) = 50 m/s (164 ft/s)

MFLWT80

Materials*)
Werb-Nr. 2807

Face: Carbon (A), SiC (Q1, Q2), Seat: SiC (Q1, Q2)
O-rings: Flexible graphite
Bellows: Alloy 718
Other parts: SS316 (1.4571), Ni42 (1.3917)
With rotary bellows. MFLWT80 for arr. 1 and 2 (ext. press.),
MFLWT90 for arr. 3 (internal pressurization).

MFLWT80/90

Werb-Nr.

Operating limits
p1(max) = 25 bar g / 23 bar g (363 PSI / 334 PSI)
2805
t1 = -20400 C (-4750 F)
For temperatures below -20 C (-4 F) MFLCT 80/92
vg(max) = 23 m/s (75 ft/s)
Materials*)
Face: Carbon (A), SiC (Q1, Q2), Seat: SiC (Q1, Q2)
O-rings: Flexible graphite, Bellows: Alloy 718
Other parts: SS316 (1.4571), Ni42 (1.3917)
Operating limits refer to default seal face combination
Carbon/SIC.
*) Default

Werb-Nr. 2808

14

and optional materials available.

EagleBurgmann
MFL 85

Gas Seals Type A

EagleBurgmann
mechanical seal type
MFL65S2/125-TA1 in
Byron Jackson pump
to seal vacuum gas oil.
Temperature: 260 C,
pressure 12 bar.

Quench oil pump (Ruhrpumpen) with

EagleBurgmann gas-lubricated RGS-D1/143
and GSS buffer gas supply system.
p1 = 1 bar; t1 = +191 C ... 215 C;
n = 1,500 min1; medium: quenching oil
with 3 % solid content.

CGSH-KD

3NC-BB

CGSH-D

Operating limits
p1(max) = 25 bar g (363 PSI)
t1 = -20 176 C (-4 350 F)
vg(max) = 23 m/s (75 ft/s)
Materials*)

HRGS-DC
Face: Carbon (A), SiC (Q1, Q2)

Seat: SiC (Q1, Q2)

O-rings: FKM, FFKM, EPDM, NBR, HNBR
Springs: Alloy C-276**)
Other parts: SS316 (1.4571)

HRGS-DC

3NC-BB

Operating limits
p1(max) = 25 bar g (363 PSI)
t1 = -20 176 C (-4 350 F)
vg(max) = 23 m/s (75 ft/s)

Werb-Nr.
2799
Materials*)
HRGS-DD

EagleBurgmann CGSH

Face: Carbon (A), SiC (Q1, Q2)

Seat: SiC (Q1, Q2)
O-rings: FKM, FFKM, EPDM, NBR, HNBR
Springs: Alloy C-276**)
Other parts: SS316 (1.4571)

HRGS-DD

3NC-FB

Operating limits
p1(max) = 41 bar g (600 PSI)
t1 = -20 176 C (-4 350 F)
vg(max) = 23 m/s (75 ft/s)
Materials*)

Werb-Nr.Face:
2803
Carbon (A), SiC (Q1, Q2)

Seat: SiC (Q1, Q2)

O-rings: FKM, FFKM, EPDM, NBR, HNBR
Springs: Alloy C-276**)
Other parts: SS316 (1.4571)
Operating limits refer to default seal face combination
Carbon/SIC.
*)

Default and optional materials available.

C-4 available, EagleBurgmann recommendation.

**) in

Werb-Nr. 2804

15

Containment Seals Type A

A containment seal is a safety seal. In case of primary seal failure it shall operate
for a minimum of 8 hours at seal chamber conditions. It can be found in the
default configuration 2CW-CS and the optional configuration 2NC-CS

CGSH

Containment seals can be of non-contacting or contacting kind.

Non-contacting containment seals feature aerodynamic grooves which provide
a reliable lift-off of the seal faces even at low velocities.
Contacting containment seals are used in connection with liquid buffer systems
but may also be used as dry running seal in connection with a Nitrogen purge.

CGSH

CS

Non-contacting containment seal

Operating limits
p1(max) = 25 bar g (363 PSI)
t1 = -20 176 C (-4 350 F)
= 23 m/s (75 ft/s)
vg(max)EM300
Materials
Face: Carbon (A), SiC (Q1, Q2)
Seat: SiC (Q1, Q2)
O-rings: FKM, FFKM, EPDM, NBR, HNBR
Springs: Alloy C-276**)
Other parts: SS316 (1.4571)

EagleEM300

CS

Contacting containment seal

Operating limits
p1(max) = 2 bar g (29 PSI), dry operation
t1 = -40 176 C (-40 350 F)
vg(max) = 23 m/s (75 ft/s)
In the event of primary seal failure the EM300 will work as a
conventional wet lubricated seal in pressures up to 60 bar g
Werb-Nr.
2798
(870 PSI) for at least 8 hours.
Materials
Face: Special carbon
Seat: Pressureless sintered SiC
O-rings: FKM, FFKM, EPDM, FVMQ
Springs: Alloy C-276
Other parts: SS316
**) in

C-4 available, EagleBurgmann recommendation.

Werb.Nr. 2827

16

API Plans Overview

Statoil

An API plan determines the piping or auxiliary system which is connected to the
seal chamber or/and the mechanical seal cartridge. Certain seal configurations
only work in combination with appropriate API plans. Other API plans can also
be applied to improve the performance of a mechanical seal. The combination of
external control and supply units which are used to realize a certain API plan is
usually called a Supply System.

EagleBurgmann
MFL 65

Gas oil charge feed

pump sealed with
EagleBurgmann MFL65
and HSHF1 in tandem
arrangement.
Temperature 280 C,
pressure 3.5 to 15 bar.

17

API Plans Process Side

For general
applications. Product
pumped is clean,
good lubrication
properties and heat
removal from the
mechanical seal.
Internal circulation
from the pump
discharge to the seal.

Seal chamber
cooling and neck
bush are necessary,
unless otherwise
specified. Dead
end seal chamber
with no circulation.
Plugged connections
for possible future
circulation and
quench.

Used when the

product being
pumped has
occasional particles
only. Recirculation
from pump discharge
through a strainer and
flow control orifice to
the seal.

Used where the seal

chamber pressure is
at discharge pressure
(mainly vertical
pumps). Recirculation
from seal chamber
through a flow control
orifice and back to
pump suction

18

Plan 01

Plan 02

Plan 11 (12)

Plan 12: With strainer St

St

Plan 13

API Plans Process Side

Used where cooling

flow is supplied to
seal while providing
venting of seal
chamber (generally
used for vertical
pumps). Recirculation
from pump discharge
through a flow control
orifice to the seal and
simultaneously from
the seal chamber
through a control
orifice to pump suction.

Used for hot

applications or where
the temperature
and pressure in the
seal chamber is
close to the vapour
curve of the product.
Recirculation from
pump discharge
through a flow control
orifice and cooler into
the seal chamber.

Used for hot liquid

applications or where
the temperature
and pressure in the
seal chamber is
close to the vapour
curve of the product.
Recirculation by
means of a pumping
ring in seal chamber
through a cooler and
back to seal chamber.

Used in applications
with suspended
solids where the SG
of the particles is
2x that of the liquid.
Recirculation from
pump discharge
through a cyclone
separator, clean fluid
to seal chamber, dirty
fluid to suction.

Plan 14

Plan 22 (21)

Plan 21: Without strainer St

St

Plan 23

EagleBurgmann reference (Plan 12 / 21 / 22 / 23 / 31 / 41)

Water cooler
WE6045/M014-D0 (SS316L, 45/16 bar, 125 C, BW 1/2 600 lbs)
WE6045/M015-D0 (SS316L, 45/16 bar, 125 C, BW 3/4 600 lbs)
WE6045/M016-D0 (SS316L, 45/16 bar, 125 C, 1/2 NPTF)
WE6045/M017-D0 (SS316L, 45/16 bar, 125 C, 3/4 NPTF)
WE6045/A001 (316 L, 45/16 bar, 125 C, SW 3/4 600 lbs)
alternative
WE6045/A002 (316 L, 45/16 bar, 125 C, SW 1/2 600 lbs
Air fin cooler
WEL1000/A067 (3/4 NPTF, 110 bar, 200 C, SS316, 2 tubes)
WEL1000/A068 (3/4 NPTF, 110 bar, 200 C, SS316, 4 tubes)
WEL1000/A069 (3/4 NPTF, 110 bar, 200 C, SS316, 6 tubes)
WEL1000/A070 (flange 3/4 600 lbs, 50 bar, 200 C, SS316, 2 tubes)
WEL1000/A070 (flange 3/4 600 lbs, 50 bar, 200 C, SS316, 4 tubes)
WEL1000/A070 (flange 3/4 600 lbs, 50 bar, 200 C, SS316, 6 tubes)
Temperature measuring unit
SP23-294-D0 (3/4 NPT, dia. 100, 0 ... 120 C, threaded thermowell)
SP23-295-D0 (flange 3/4, 600 lbs RF, dia. 100, 0 ... 120 C, threaded thermowell)
SP23-299-D0 (flange 3/4, 600 lbs RF, dia. 100, 0 ... 120 C, flanged thermowell)

Plan 31

Orifice
SP24-047-D0 (3/4 NPT, bore dia. 3 mm)
SP24-048-D0 (flange 3/4, 600 lbs, RF, bore dia. 3 mm)
Strainer
SP18-023-D0 (3/4 NPT)
SP18-024-D0 (flange 3/4)
Cyclone separator
ZY62/1/2NPT-00 (SS316, 64 bar, 125 C, 1/2 NPT)
ZY62S2/NW21-D0 (SS316, 64 bar, 125 C, WN 1/2 600 lbs)
ZY203/3/4NPT-00 (SS316, 200 bar, 3/4 NPT)
ZY203/NW20-D0 (SS316, 80 bar, 150 C, WN 3/4 1500 lbs)

19

API Plans Process Side

Used when the

product being
pumped does not
have good lubrication
properties, contains
suspended solids or
is hazardous. Flush
injecton of clean fluid
into the seal chamber
from an external
source.

Used in applications
with suspended
solids where the SG
of the particles is
2x that of the liquid.
Temperature and
pressure in the seal
chamber is close to
the vapour pressure
of the product.
Recirculation from
pump discharge
through a cyclone
separator, delivering
clean fluid to a cooler
and then to the seal
chamber.

Plan 32

EagleBurgmann reference (Plan 32)

Flush unit
SP24-043-D0 (16 bar, 220 l/min water, SS 316)

Plan 41

EagleBurgmann ZY203
cyclone separator

20

API Plans Between seals

EagleBurgmann GSS
buffer gas panel

Used where the

pumped product is
harmful / hazardous
and / or buffer fluid
may not contaminate
the product. External
reservoir at pressure
below seal chamber
pressure. Pumping
device providing
buffer liquid forced
circulation.

Plan 51

Plan 52

EagleBurgmann reference (Plan 51)

Quench fluid tank
QFT6000/M001-DO (3 liter, 80 C, SS 316)

EagleBurgmann reference (Plan 52)

< 60 mm
Thermosiphon system for shaft diameter =
TS6000/M052-D0 (12 liter, ASME, NPT-connection)
TS6001/M052-D0 (12 liter, PED, NPT-connection)
TS6000/M001-D0 (12 liter, ASME, Flange-connection)
TS6001/M001-D0 (12 liter, PED, Flange-connection)

Thermosiphon system for shaft diameter = 60 mm

TS6002/M052-D0 (20 liter, ASME, NPT-connection)
TS6003/M052-D0 (20 liter, PED, NPT-connection)
TS6002/M004-D0 (20 liter, ASME, Flange-connection)
TS6003/M003-D0 (20 liter, PED, Flange-connection)
<

Used with products

that usually solidify
when coming into
contact with air /
ambient temperature.
External reservoir
providing a deadended blanket for
fluid to the quench
connection of the
gland.

21

API Plans Between seals

Used for hot
applications or
where products
have low pressure
and are harmful/
hazardous. External
reservoir pressurized
above seal chamber
pressure providing
barrier fluid to
mechanical seals.
Pumpng device
providing forced
circulation.

Plan 53A

EagleBurgmann reference (Plan 53A)

< 60 mm
Thermosiphon system for shaft dia. =
TS6000/M053-D0 (12 liter, ASME, NPT-connection)
TS6001/M053-D0 (12 liter, PED, NPT-connection)
TS6000/M002-D0 (12 liter, ASME, Flange-connection)
TS6001/M002-D0 (12 liter, PED, Flange-connection)

Thermosiphon system for shaft dia. = 60 mm

TS6002/M053-D0 (20 liter, ASME, NPT-connection)
TS6003/M053-D0 (20 liter, PED, NPT-connection)
TS6002/M005-D0 (20 liter, ASME, Flange-connection)
TS6003/M004-D0 (20 liter, PED, Flange-connection)
<

Used for applications

where products have
high pressure and are
harmful/hazardous.
Pre-pressurized
bladder accumulator
provides pressure to
circulation system.
Heat removed by air/
water heat exchanger.
Pumping device
providing forced
circulation.

Plan 53B

EagleBurgmann reference (Plan 53B)

Bladder accumulator system with air fin cooler
SPO9050/M001-D0 (20 liter, PED, NPT-connection, 50 bar)
SPO9050/M031-D0 (20 liter, PED, Flange-connection, 50 bar)
SPO9050/M032-D0 (20 liter, ASME, Flange-connection, 50 bar)
SPO9050/M036-D0 (20 liter, ASME, NPT-connection, 50 bar)
Alternative with water cooler
WE 6045/M...

Used for applications

where products have
high pressure and are
harmful/hazardous.
Pressurization by
reference line from
seal chamber to a
piston accumulator
provides pressurized
barrier fluid. Pumping
device providing
forced circulation.

Plan 53C

EagleBurgmann reference (Plan 53C)

Piston accumulator system with air fin cooler
SPO9050/M002-D0 (50 bar, 2 liter, NPT-connection, PED)
SPO9050/M033-D0 (50 bar, 2 liter, NPT-connection, ASME)
SPO9050/M034-D0 (50 bar, 2 liter, Flange-connection, ASME)
SPO9050/M035-D0 (50 bar, 2 liter, Flange-connection, PED)
Alternative with water cooler
WE 6045/M...

A N2

Used in harmful/
hazardous
applications.
Pressurized clean
barrier fluid from
an external system.
Fluid circulation by
an external pump or
pressure system.

Plan 54

EagleBurgmann reference
(Plan 54)
Barrier liquid
SPA

EagleBurgmann
TS 6000
thermosiphon system

22

API Plans Between seals

Applicable with
hydrocarbons
normally used in
conjunction with
plan 75 or plan 76.
Externally supplied
gas buffer (pressure
lower than seal
chamber pressure).
Buffer gas may be
used to dilute seal
leakage.

Plan 72 (71)
Plan 71: Plugged connections

EagleBurgmann reference (Plan 72)

A

Buffer gas panel

GSS4000/A001-D0 (EExd, 16 bar, 0.6 6 Nl/min N2)
(built into box)
GSS4000/A002-D0 (EExd, 16 bar, 0.6 6 Nl/min N2)

A
B
C
D

connect to plan 75
connect to plan 76
N2
quench connection to be located downwards

Used in applications
where the product is
harmful/hazardous.
Externally supplied
barrier gas used to
positively prevent
process fluid
from leaking to
atmosphere.
Pressure of barrier
gas higher than seal
chamber pressure.

EagleBurgmann Reference
(Plan 74)

Plan 74

Barrier gas panel

GSS4016/A324-D0
(EExi, 16 bar, 50 C, 0.66 Nl/min N2)
GSS4016/A326-D0
(EExd, 16 bar, 50 C, 0.66 Nl/min N2)

A N2

Application
when pump fluid
condenses at ambient
temperatures.
Containment seal
chamber drain for
condensing leakage.

EagleBurgmann reference (Plan 75)

Plan 75
A

Leakage collecting system

LS050/M001-D0 (50 bar, 120 C, 14 liter, ASME, NPT-connection)

Application where
pump fluid does
not condense at
ambient temperature.
Containment seal
chamber vent for noncondensing leakage.

Plan 76

EagleBurgmann reference (Plan 76)

Vapour recovery system
SP23-228-D0 (50 bar, 80C, Pl dia. 100 mm, Pressure switch EExi)

A Device to be located below pump shaft

B To drain
C To flare

23

API Plans Atmospheric side

Used to keep
atmospheric side of
seal clean. External
source providing a
flow-through quench
at atmospheric side.

Plan 62 (61)

EagleBurgmann reference (Plan 62)

Plan 61: Plugged Quench connection

External water quench system

SP24-043-D0 (16 bar, 220l/min water, SS 316)
Steam quench
Atmosheric side

Used for
leakage detection
on single seal.
Atmospheric side
leakage collection
and monitoring
(alarm high) in
external vessel.

EagleBurgmann reference (Plan 65)

Plan 65

Leakage detection system

LS050/M002-D0 (EExi, NPT-connection)

53B SPO bladder

accumulator system

24

Appendix
The following tables give a quick overview about the requirements of the
different categories, the selection of suitable buffer or barrier fluids and the seal
coding system according to API 682 / ISO 21049 and the EagleBurgmann seal
code.

EagleBurgmann
mechanical seal
MFLW85S20 in pump
(Thyssen Ruhrpumpen)
to seal gas oil with
sulphur. Temperature
217 C,
pressure 2.3 bar.

25

EagleBurgmann API 682 tools

Seal Selection Program
according to API 682 3rd edition and ISO 21049

A valuable aid for selecting mechanical seals acc. to API 682 3rd edition.
The software on this CD-ROM provides a step-by-step guide
to selecting the appropriate sealing system for any API related application.
While doing so, it follows the seal selection procedure as it is intended by
the API 682 3rd edition.
Available upon request at your nearest EagleBurgmann location or via e-mail:
[email protected]

API 682 Poster:

API 682 at a glance: Double sided printing shows the most common API plans on
one side and overleaf illustrates the seal classification system acc. to API 682
Size: DIN A 1 (594 x 841 mm).

API 682 Short guide:

This handy booklet provides valuable hands-on operational information, API plan
descriptions, start-up and shut-down procedures, recommendations for regular
inspection and troubleshooting for the most common API plans.

26

Selection of Buffer and Barrier Mediums

Seal Coding System
Sealed fluid
Above 10 C
Below 10 C

Aqueous streams

Hydrocarbon streams

Barrier/buffer fluid

Special notes
100 mm2/s at 38 C and
1 mm2/s to 10 mm2/s at 100 C
5 mm2/s to 40 mm2/s at 38 C and
1 mm2/s to 10 mm2/s at 100 C
Ethylene glycol may be considered as
hazardous material and/or waste

Hydrocarbon fluid

Mixture of water and

ethylene glycol

Dont use commercially available automotive

antifreeze (plating of additives at seal parts)

Mixture of water and

propylene glycol
Paraffin-based high purity oils
Synthetic-based oils

With little or no additive for wear/oxidation

resistance (plating of additives at seal parts)

ISO 21049
API 682

Seal category
Step I

Seal arrangement
Step II

Seal type
Step III

Letters and numbers

C1, C2, C3

A1, A2, A3

A, B, C

Note

Example
EagleBurgmann
Letters and numbers
Note
Example 1
Example 2
Example 3

General demands
Three years continuous operation without adverse
deterioration.
Uncritical normal buffer/barrier fluid leakage.
Compatibility with the sealed medium.
Compatibility with the materials of the sealing system
initial boiling point min. 28 C above exposed temperature.
Flash point > service temperature (if O2 is present).
Compatibility with max./ min. process temperature.
Freezing temperature < ambient temperature at site.
Viscosity < 500 mm2/s at minimum temperature.
Viscosity over the entire operating-temperature range.
Consider gas solubility in viscous barrier fluids (> 10 bar).

API plans
Step IV
01, 02, 11, 12, 13, 14, 21, 22, 23, 31, 32, 41, 51, 52, 53A, 53B, 53C,
54, 61, 62, 65, 71, 72, 74, 75, 76

Arrangement 1 can be a 1CW-FX or 1CW-FL

Arrangement 2 can be a 2CW-CW, 2CW-CS or 2NC-CS
Arrangement 3 can be a 3CW-FB, 3CW-FF, 3CW-BB, 3NC-FB, 3NC-FF or 3NC-BB
Seal materials are not part of this code (default materials assumed)
A code for engineered mechanical seals (ES) is not specified
Features: category 2, arrangement 2, type A, flush plan 11 and flush plan 52
Code: C2A2A1152
Seal family

Design details
Materials process side seal atmospheric side seal
-E ... (single seal)
H75VN, MFL85 / 90
/mm
-PTA ... (tandem seal)
according to EN 12756
MFL65, MFLWT80 / 90
/inch
-D ... (back-to-back) e.g. Q2Q2VMG-AQ2VMG
CGSH, ...

(face-to-face)
Coding: EagleBurgmann seal code, material code (ISO 21049 seal code, configuration code)
Features: Rotating metal bellows seal, seal diameter 70 mm, single seal, materials
Code: MFL85N/70-EX, AQ2VM5G, (C2A1B1162, 1CW-FL)
Features: Pusher type seal, inboard seal diameter 50 mm, tandem arrangement, materials
Code: H75VK/50-PTAX, Q2Q2VMG-AQ2VMG, (C2A2A1152, 2CW-CW)
Features: Engineered mechanical seal (ES), seal diameter 210 mm, single seal, materials
Code: SHV/210-EX, AQ2VMG, (C2A1ES1161, 1CW-FX)

Return pump (KSB) with EagleBurgmann

tandem seal type H75S2/60-H75F2/55
according to API 682 Plan 52 for sealing C
hydrocarbon. Buffer medium: methanol.

Seal diameter

EagleBurgmann
mechanical seal
type MFLWT80/
S1-FD/58-E3 with
thermosiphon system
TS2000/M073-A1
to seal ethylene oxide
(Sulzer pumps).

27

Objectives and Category Details

API 682 and ISO 21049**)

Category 1***)

Objective 1*): seal operation

Continuously for 25,000 h without need for replacement

Objective 2*): containment seal operation

Objective 3*): emissions
Basic design features (4.1.3 / 6.1)
Throttle bushing requirement for
arrangement 2 and 3 seals (7.2.3 /
7.3.3.1)
Flush connection to the process side
for arrangement 3 seals (7.3.3.2)
Shaft diameter (1)
Seal chamber size (4.1.2)
Cartridge seal sleeve size increments
required
Temperature range (4.1.2)
Pressure range, absolute (4.1.2)
Face materials (6.1.6.2)
Gland plate metal-to-metal contact
requirement
Tangential buffer/barrier fluid outlet for
arr. 2 and 3 seals (7.2.4.2 / 7.3.4.3)
Throttle bushing design requirement for
arrangement 1 seals (7.1.2.1)
Scope of vendor qualification test

Category 2

Category 3

At least 25.000 h without need for replacement at any containment seal chamber pressure equal to or less than the seal
leakage pressure switch setting (< 0,7 bar g (10 PSI)) and for at least 8 h at the seal chamber conditions.
Complying with local emissions regulations or exhibiting a maximum screening value of 1,000 ml/m3 (1,000 ppm vol.) as
measured by the EPA Method 21, whichever is more stringent.
Balanced mechanical seal, inside-mounted, cartridge design, type SS316 (1.4571) or better for sleeve and housing
Fixed carbon, if specified
If specified
20 mm (0.75 inch) to 110 mm (4.3 inch)
ISO 3069 type C,
ISO 13709 / API 610 10th edition
ASME B73.1 and ASME B73.2
None

10 mm increments (6.2.2.3.1)

-40 to 260 C (-40 to 500 F)

22 bar a (315 PSI)
Premium blister-resistant carbon (A) vs.
self-sintered silicon carbide (Q1)

-40 to 400 C (-40 to 750 F)

42 bar a (615 PSI)
Premium blister-resistant carbon (A)
vs. reaction-bonded silicon carbide (Q2)

Required (6.2.1.2.2)

Required inside and outside the stud circle diameter (6.2.2.2.2)

If specified
Fixed carbon
Fixed, non-sparking metal
Floating carbon option (7.1.2.2)
Test as category 1
Test as category 2
Unless faces interchangeable with category 3 (10.3.1.2.3)

Distributed inlet flush requirements

When required or if specified (6.1.2.14 / 6.2.1.2.1)
arr. 1 and 2 with rotating flexible element
Seal circulation device head flow curve
If specified
provided (8.6.2.2)
Proposal data requirements (11.2.1)
Minimal
Contract data requirements (11.3.1)

Required
Floating carbon
Test as category 3, entire seal
assembly as a unit (10.3.1.2.2)
Required (6.2.3.2)
Required
Rigorous

*) All technical specifications are based on extensive tests

and our many years of experience. The diversity of possible
applications means, however, that they can serve only as
guide values. We must be notified of the exact conditions
of application before we can provide any guarantee for a
specific case. Subject to change.
**) API / ISO paragraphs in brackets
***) Please also ask for EagleBurgmann Apitex mechanical
seals

Pump (Ruhrpumpen)
with EagleBurgmann
seal H75S2/70-FTA1
according to
API 682, plan 52.
Medium: C -fraction;
barrier fluid: methanol
3

Recycle oil pump (BW/IP) with tandem seal

H75S2/85-FTA5 according to API 682
plan 52 to seal hydrocarbons.
Temperature -13 C, Barrier fluid: methanol.

28

EagleBurgmann in Profile
Certifications
BURGMANN
ISO 9001:2000
EN 9100
ISO 14001
OHSAS 18001

Burgmann Headquarters Wolfratshausen (D)

EagleBurgmann Niigata (J)

Plant Eurasburg (D)

Plant Judenburg (A)

ATEX 94/9/EG
QHD
Qualified Hygienic
Design VDMA
DIN/EN 729-2
HPO certified
KTA 1401
Certified for
Nuclear
Power Plants
ISO TS 16949
WHG
Fachbetrieb ( 19)
Germanischer Lloyd
Approvals
IHK
Prfungsbetrieb
Umweltpakt
Bayern
__________
All current
certificates:
www.burgmann.com/
QM

An alliance with a great deal to offer our customers and partners

Burgmann and the leading Japanese mechanical seal manufacturer Eagle Industry
have laid the foundation for a global cooperation: an alliance with a pronounced
understanding for quality and service as well as customer orientation.
The basis of this arrangement is an intensive and trust-based cooperation that
notably strengthens the global competitiveness of both partners and makes them
one of the top suppliers of sealing technology on the world market. A worldwide
presence, market-orientated products and high-quality services are further key
factors of success. All this, together with the know-how and dedication of our
employees, means that we have considerable potential to offer our customers.
We are there when you need us
Customers want proximity, speed and solutions to their problems. Thanks to
our worldwide presence, flexibility and specialist know-how we can face these
challenges with quiet confidence. All over the world we offer our in-depth package
of services from the simple stuffing box packing to the complex high-tech seal,
plus the backing of our TotalSealCareTM modular support offering, which allows
each customer to put together exactly the right service package based on individual
needs and requirements. Numerous service contracts and international agreements
attest to the trust which top-name companies place in our expertise and confirm
the quality of our services.
Making our customers more successful
Our customers expect their machines to operate without problems. With this
objective in mind, we are working to produce innovative, economically rational
and easy-to-use seal solutions that help to fulfill the highest requirements in terms
of environmental protection and safety. In doing so, it is our intention to increase
our customers efficiency and productivity and to put across our global profile as
a reliable, competent partner for high quality and technological leadership. The
technical knowledge, creativity, motivation and performance of our workforce makes
a major contribution to achieving these objectives and making our customers more
successful.

29

EagleBurgmann in your vicinity

Chilicote S.A.
Avda. Julio A. Roca 546
C1067 ABN Buenos Aires,
Argentina
Phone +54 / 11 / 43 43 84 69
Telefax +54 / 11 / 43 31 42 78
Australia
EagleBurgmann Australia Pty. Ltd.
16 Stennett Road,
Ingleburn, NSW 2565
Phone +61/ 2 / 96 05 64 44
Telefax +61/ 2 / 98 29 69 58
Austria
EagleBurgmann Austria GmbH
Vogelweiderstrae 44 a
A-5020 Salzburg
Phone +43 / 662 / 82 57 01
Telefax +43 / 662 / 82 57 03
Belarus
Filter CJSV
Logoisky tract and MCAD crossing
Administrative building
Expobel - Office 501
223053 Minsky district
Phone +375 17 237 9365
Telefax +375 17 237 9363
Belgium
EagleBurgmann Belgium B.V.B.A.
Zagerijstraat 11
B-2960 Sint-Job-in't-Goor
Phone +32 / 3 / 6 33 99 44
Telefax +32 / 3 / 6 33 99 49
Brazil
EagleBurgmann do Brasil
Vedaoes Industriais Ltda.
Av. Sta. Izabel, 1721
CEP - 13084-643 Barao Geraldo
Caixa Postal 65 60
Campinas - Sao Paulo
Phone +55 /19 / 37 49 97 40
Telefax +55 /19 / 37 49 97 42
Canada
EagleBurgmann Canada Inc.
8699 Escarpment Way,
Units #9 & #10
Milton, Ontario / Canada L9T 0J5
Phone +1/ 905 / 693 87 82
Telefax +1/ 905 / 693 05 35
Nova Magnetics-Burgmann Ltd.
One Research Drive
Dartmouth, Nova Scotia
Canada B2Y 4M9
Phone +1/ 902 / 465 66 25
Telefax +1 / 902 / 465 66 29
Chile
SelloTecno Ltda.
Luis Thayer Ojeda No. 0130
OF 806 Providencia Santiago
Chile
Phone +56 / 2 / 333 33 03
Telefax +56 / 2 / 333 25 19
China
Burgmann Shanghai Ltd.
No. 127-8 Wenjing Road
Minhang, Shanghai
People's Republic of China
Phone +86 / 21/ 64 62 05 50
Telefax +86 / 21/ 64 30 02 19
Burgmann Dalian Ltd.
No. 86 Liaohe East Road, DD Port
116620 Dalian
People's Republic of China
Phone +86 / 411 8758 1000
Telefax +86 / 411 8758 1418
EBI (Shanghai)
Investment Management Co. Ltd.
Room 205 B Cimic Tower
No. 1090 Century Ave. Pudong
201120 Shanghai
People's Republic of China
Phone +86 21 58 36 15 99
Telefax +86 21 58 35 48 38
Colombia
William Tobon & Cia.
Cr. 7 - 64 - 50 - Ext. 301
Santaf de Bogota
Phone +57 / 1 / 211 76 75
Telefax +57 / 1 / 211 76 75
Cyprus & Lebanon
TRCI Ltd.
122, Limassol Ave. PO Box 24371
1703 Nicosia, Cyprus
Phone+357 22 42 79 80
Telefax +357 22 42 30 21
Czech Republic
EagleBurgmann Czech s.r.o.
Na Drahach 1364
CZ-15600 Praha 5 Zbraslav
Phone +420 / 2 / 57 92 05 05
Telefax +420 / 2 / 57 92 05 08
KE-Burgmann Czech s.r.o.
V Lznich 395
CZ-254 01 Jilove u Prahy
Phone +420 / 2 / 41 02 18 11
Telefax +420 / 2 / 41 02 18 30

Denmark
KE-Burgmann A/S
Expansion Joints Division
Park All 34,
DK-6600 Vejen
Phone +45 / 75 36 18 11
Telefax +45 / 75 36 15 32
KE-Burgmann A/S
Seals Division
Industrisvinget 1,
DK-6600 Vejen
Phone +45 / 75 36 49 88
Telefax +45 / 75 36 39 88
KE-Burgmann Bredan A/S
Odinsvej 1, Box 129
DK-6950 Ringkobing
Phone +45 / 96 74 28 00
Telefax +45 / 97 32 36 31
Ecuador
Petroconsultant S.A.
Fco. de Goya 262
Urb. Los Cipresses II
El Condado
P.O. Box 17-17-1254, Quito
Phone +593 / 2 / 49 17 52
Telefax +593 / 2 / 49 35 09
Egypt
Alimex Alexandria
Import Export
258 Abdel Salam Aref Str.
Louran - El Saray
Alexandria POB 313
Phone +20 / 3 / 5 81 00 60
Telefax+20 / 3 / 5 81 00 65
Estonia
Filter AS
Like tee 9, Peetri Kla, Rae vald,
EE-75312 Harjumaa
Phone +00372 742 24 29
Telefax +00372 512 012 0
Finland
KE-Burgmann Finland Oy
Expansion Joints
P.O. Box 139, Ensimminen Savu
SF-01510 Vantaa
Phone +358 / 9 / 82 55 01
Telefax +358 / 9 / 82 55 02 00
Tiivistetekniikka Oy
Mkituvantie 5,
SF-01510 Vantaa
Phone +358 / 207 65 171
Telefax +359 / 207 65 20 07
France
EagleBurgmann France SAS
Zone dActivit les Perriers
106/108 Route de Cormeilles
BP 96,
F-78505 Sartrouville
Phone +33 / 1/ 30 86 50 20
Telefax +33 /1/ 39 15 16 07
Great Britain
EagleBurgmann Industries
UK LP
12, Welton Road
Wedgnock Industrial Estate
GB-Warwick CV 34 5PZ
Phone +44 /1926 / 41 76 00
Telefax +44 /1926 / 41 76 17
KE-Burgmann U.K.
Eaton Bank, Congleton
GB-Cheshire SW12 1NZ
Phone + 44 / 1260 / 29 12 89
Telefax + 44 / 1260 / 29 13 03
Greece
A.G. Stambolidis & Co.
Mitrodorou 22
GR-10441 Athen
Phone +30 /21/ 05 15 06 65
Telefax +30 /21/ 05 15 08 10
Hungary
EagleBurgmann Hungaria Kft.
Lejt utca 6
H-1124 Budapest
Phone +36 /1/ 3 19 81 31
Telefax +36 /1/ 3 19 81 25
India
Burgmann India PVT. LTD.
A.K. Industrial Estate
Madina Manzil Compound
S.V. Road, Goregaon (West)
Bombay 400 062
Phone +91/ 22 / 28 74 15 34
Telefax +91/ 22 / 28 74 88 10
Eagle Seals & Systems India Ltd.
212/2, Hadapsar
Off. Soli Poonawalla Road
Pune 411 028 India
Phone +91 / 20 / 2699 3900
Telefax +91 / 20 / 2699 3921

Irak
WTE
Ukba Sq., Mahala 929
Zuhak 2, House No. 5
P.O. Box No. 2421
Al Jadria, Baghdad
Phone +964 171 99033
Telefax +964 171 93034
Iran
Burgmann Pars
Sealing Systems Co.
No. 1, Kokab Alley,
Pasdaran Ave.
Teheran
Phone +98 / 21/ 2 86 28 19
Telefax +98 / 21/ 2 85 44 81
Israel
ETA Engineering Ltd.
P.O. Box 890
Ramat-Gan 52108
18 Tushia St.
Phone +972 / 3 / 6 24 19 45
Telefax +972 / 3 / 5 62 84 75
Italy
EagleBurgmann Italia s.r.l.
Viale Martiri della Liberazione, 12
I-23875 Osnago (LC)
Phone +39 / 039 / 95 22 501
Telefax +39 / 039 / 928 94 83
BT-Burgmann S.P.A.
Via Meucci, 58
I-36057 Arcugnano (Vi)
Phone +39 / 0444 / 28 89 77
Telefax +39 / 0444 / 28 86 93
Japan
Eagle Industry Co., Ltd.
General Industry Overseas
Sales Dept.
Marketing & Sales Division
1-12-15, Shiba-Daimon, Minato-ku
Tokyo, 105-8587
Phone +81/ 3 / 3432-4771
Telefax +81/ 3 / 3438-2370
Jordan
Eman Essa Trading Est.
P.O. Box 840067
Amman 11180
Phone +96 / 279 / 5 57 66 92
Telefax +96 / 265 / 66 55 96
Kazachstan
Globe Interstar
Furmanova Street 240, Office 18
050059 Almaty
Phone +7 / 327 / 264 34 86
Telefax +7 / 327 / 264 33 82
Korea
EagleBurgmann Korea Co. Ltd.
541, Suwolam-Ri, Seotan-Myon
Pyongtaek-Si, Kyongki-Do,
-451-850-,
Pyongtaek Yosu Busan Daegu
Phone +82 / 31/ 664-40 95
Telefax +82 / 31/ 664-40 94
Branch Offices: Ulsan
Kuwait
Dan Trading & Contracting
Co. W.L.L.
P.O. Box 5092
13051 Safat, Kuwait
Phone +965 / 2 43 25 53
Telefax +965 / 2 43 78 33
Latvia
Filter SIA
Aizkraukles 21
10069 Riga
Phone +00371 7801 921
Telefax +00371 7550 224
Libya
United Technical & Engineering
Miseran St.
P.O. Box 81276
Tripoli G.S.P.L.A.J.
Phone +218 21 4442 641
Telefax +218 21 4776 152
Lithuania
Dmitri Melnikow
Balandziu 5 - 2
LT-91188 Klaipeda
Phone / Fax +370 46 31 29 49
Mobile +370 69 82 14 27
Malaysia
EagleBurgmann (Malaysia)
Sdn. Bhd.
No. 7, Lorong SS13, 6 B
Off Jalan SS13/6
Subang Jaya Industrial Estate
47500 Petaling Jaya
Phone +60 / 3 / 56 34 86 24
Telefax +60 / 3 / 56 34 97 42

KE-Burgmann
Flexibles India Pvt. Ltd.
Survey No. 1426
Nagappa Industrial Estate,194
G.N.T. Road, Puzhal
Chennai 600 066 , India
Phone +91 / 44 / 6 59 06 32
Telefax +91 / 44 / 6 59 09 17

Mexico
EagleBurgmann Mexico
S.A. de C.V.
Calzada de Guadalupe
Num. 350-6, Col. El Cerrito
C.P. 54720, Cuautitln Izcalli,
Estado de Mxico, Mexico City
Phone +52 / 55 / 58 72 53 93
Telefax +52 / 55 / 58 72 64 93

Indonesia
PT EagleBurgmann Indonesia
Jl. Jababeka Blok J6-E
Kawasan Industri Cikarang
Bekasi 17550 - Jawa Barat
Phone +62 / 21/ 8 93 53 13
Telefax +62 / 21/ 8 93 53 15

Morocco
Petro-Mat
Angle Rue Michel de l'Hpital
et Rue Jules Cesar
Casablanca 05
Phone +212 / 240 / 87 99
Telefax +212 / 240 /19 39

Netherlands
EagleBurgmann Netherlands B.V.
Koningsschot 9
NL-3905 PP Veenendaal
Phone +31/ 318 / 54 20 00
Telefax +31/ 318 / 54 15 35
New Zealand
EagleBurgmann New Zealand Ltd.
P.O. Box 34285, Birkenhead,
3 Parity Place, Glenfield, Auckland
Phone +64 / 9 / 4 43 57 72
Telefax +64 / 9 / 4 41 27 66
Nigeria
Sealing Engineering Services Ltd.
82 St. Finbarr's College Road
Akoka / Yaba, Lagos
Phone +234 /1/ 82 59 09
Telefax +234 /1/ 82 59 09
Norway
EagleBurgmann Norway AS
P.O. Box 143
Industriveien 25 D
N-2021 Skedsmokorset
Phone +47 / 64 / 83 75 50
Telefax +47 / 64 / 83 75 75
Oman
Overseas Petroleum
Equipment Co. L.L.C.
P.O. Box 261, Hamriya
Postal Code 131, Sultanate
of Oman
Phone +968 / 60 21 82
Telefax +968 / 60 20 84
Pakistan
Azif Asim Associates
Suit #02, 1st Floor,
Sameer plaza Civic Center, 3-C1
Faisal Town
54660 Lahore, Pakistan
Phone +92 / 42 / 111 585
Telefax +92 / 42 / 516 83 44
Techno-Mech Pakistan
51-A/1, Rehmanpura,
Ferozpur Road
54660 Lahore, Pakistan
Phone +92 / 42 / 757 5671
Telefax +92 / 42 / 759 7373
Peru
Corporacin Gamma S.A.C.
Av. La Marina 1321, San Miguel
Lima - Peru
Phone +51/12 / 63 76 70
Telefax +51/12 / 63 02 86
Philippines
Burgmann (Philippines) Inc.
No. 9769 National Road, Maduya
Carmona, Cavite
Phone +63 / 49 / 8 39 06 55
Telefax +63 / 49 / 8 39 06 54
Poland
KE-Burgmann Polska
Splka z.o.o.
Al. Jerozolimskie 200
PL-02-486 Warszawa
Phone +48 22 535 16 00
Telefax +48 22 535 16 48
Portugal
EagleBurgmann Ibrica S.A.
Avda. de Quitapesares, 40
E-28670 Villaviciosa de Odn,
Madrid
Phone +34-91-616 66 01
Telefax +34-91-616 66 81
Qatar
Jaidah Motors and Trading Co.
P.O.Box 150
Doha / Qatar / Arabian Gulf
Phone +974 / 68 21 82
Telefax +974 / 41 41 00

Singapore
EagleBurgmann Singapore Pte. Ltd.
52 Serangoon North Avenue 4,
#03-02 Ever Tech Building
555853 Singapore
Phone +65 / 64 81 34 39
Telefax +65 / 64 81 39 34
EBI Asia Pacific Pte. Ltd.
29 International Business Park,
Acer Blg, Tower B, #03-03
609923 Singapore
Phone+65 / 65 65 66 23
Telefax +65 / 65 65 96 63
KE-Burgmann Singapore Pte. Ltd.
Expansion Joints
Blk 7 Pioneer Road North
No. 01-51, Singapore 628459
Phone +65 / 62 61 85 81
Telefax +65 / 62 61 85 89
Slovenia (CRO, BIH, MAC, YU)
Branch Office Slovenia
Malci Beliceve 37
SLO-1000 Ljubljana
Phone +386 / 1/ 4 23 15 57
Telefax +386 / 1 / 2 57 40 57
Mobile +386 / 41 / 66 13 15
Slowakian Republic
EagleBurgmann Czech s.r.o.
Na Drahach 1364
CZ-15600 Praha 5 Zbraslav
Phone +420 / 2 / 57 92 05 05
Telefax +420 / 2 / 57 92 05 08
Technosam s.r.o.
Galvaniho 2/A
SK-82104 Bratislava
Phone +421 / 2 / 43 41 35 85
Telefax +421 / 2 / 43 41 36 03
South Africa
EagleBurgmann Seals
South Africa (PTY.) LTD.
1 Brunton Circle
Founders View South,
Modderfontein
Johannesburg 2065, Gauteng,
R.S.A.
Phone +27 /11/ 4 57 90 00
Telefax +27 /11/ 6 09 16 06
Postal adress: P.O. Box 1210,
Edenvale 1610, R.S.A.
Also responsible for: Namibia,
Botswana, Swaziland, Zambia,
Zimbabwe, Mozambique,
Mauritius, Congo, Ethiopia,
Uganda, Tanzania
Spain
EagleBurgmann Ibrica S.A.
Avda. de Quitapesares, 40
E-28670 Villaviciosa de Odn,
Madrid
Phone +34-91-616 66 01
Telefax +34-91-616 66 81
Sweden
EagleBurgmann Sweden AB
Svrmaregatan 3
S-60361 Norrkping
Phone +46 /11 /14 00 05
Telefax +46 /11 /14 00 15
EagleBurgmann Sweden AB
Gteborg Office
Askims Verkstadsvg 4
S-436 34 Askim, Gteborg
Phone +46 / 31 / 58 68 50
Telefax +46 / 31 / 58 14 66
Postal adress:
Box 9101, 40093 Gteborg

Taiwan
EagleBurgmann Taiwan Co. Ltd.
1F No. 7, Lane 144 Chi Lin Rd.
Taipei
Taiwan, R.O.C.
Phone +886 -2- 2581 0040
Telefax +886 -2- 2523 2793

Russia
EagleBurgmann OOO
ul. Zheleznodorozhnaya, 1, str. 45
606524 Zavolzhye
Gorodetsky district,
Nizhny Novgorod region
Phone +7 / 831/ 6 93 05 58
Telefax +7 / 831/ 6 93 05 59

Thailand
EagleBurgmann (Thailand) Co. Ltd.
Banga Tower C, Floor 18th
40/14 Moo 12 Banga-Trad Rd.
Km. 6.5 Bangkaew, Bangplee
Samutprakarn 10540
Phone +66 / 2 / 7 51 96 21
Telefax +66 / 2 / 7 51 96 28

Moscow Representation
Ul. Novotcheremuschkinskaja 61
RF-117418 Moskau
Phone +7 / 095 / 7 97 20 14
Telefax +7 / 095 / 7 97 20 78

Trinidad
Eswil Equipment & Supply
(W.I.) Ltd
10 - 16 Lady Hailes Avenue
San Fernando, Trinidad, W. I.
P.O. Box 3585, La Romaine
Trinidad, W. I.
Phone +1/ 868 / 6 57 88 38
Telefax +1/ 868 / 6 52 90 02

Gas Arabian Services Est

P.O.Box 3422
Dammam 31471, King Saud Street
Kingdom of Saudi Arabia
Phone +96 / 63 / 8 35 15 00
Telefax +96 / 63 / 8 32 28 22

Turkmenistan
Globe Interstar
Andaliba Street 82
74011 Ashgabat
Phone +993 / 12 / 47 73 24
Telefax +993 / 12 / 47 73 25
Ukraine
IRT-Technogerm
Ul. Komsomolskaja, 130
40009 Sumy
Phone +380 542 610 324
Telefax +380 542 610 326
United Arab Emirates
EagleBurgmann Middle East FZE
P.O. Box 61310
Jebel Ali Free Zone
Dubai
Phone +971/ 4 / 8 83 88 41
Telefax +971/ 4 / 8 83 88 43
Uruguay
Bilpa S.A.
Casilla Correo 889
Cdigo Postal 11800
Santa F, 1.131 - Montevido- UY
Phone +598 / 2 / 29 33 43
Telefax +598 / 2 / 29 06 87
USA
EagleBurgmann Industries LP
10035 Brookriver Dr.
Houston, Texas 77040
Phone +1/ 713 / 9 39 95 15
Telefax +1/ 713 / 9 39 90 91
KE-Burgmann USA Inc.
2100 Conner Road
Hebron, Kentucky 41018
Phone +1 / 859 / 746 0091
Telefax +1 / 859 / 746 0094
Uzbekistan
Globe Interstar
Nukus Str. 13 / 2
100015 Tashkent
Phone +998 / 71 / 133 39 58
Telefax +998 / 71 / 133 49 74
Venezuela
EagleBurgmann Venezuela, C.A.
Calle 6 con Calle 9,
Edif. Fant Piso 2
Zona Industrial La Urbina
1070 Caracas
Phone +58 / 212 / 2 42 15 48
Telefax +58 / 212 / 2 42 45 44
Vietnam
Bavico Ltd.
97A Ly Tu Trong Street, District 1
Ho Chi Minh City, Vietnam
Phone +84 / 8 / 8 24 30 46
Telefax +84 / 8 / 8 22 35 82

Switzerland
EagleBurgmann (Switzerland) AG
Hofstrasse 21, CH-8181 Hri
Phone +41 / 44 / 8 60 88 00
Telefax +41/ 44 / 8 61 01 35

Romania
EagleBurgmann RO S.R.L.
Bdul. Iuliu Maniu, Nr. 7
Cladirea E, Parter, Hala 3, Sector
RO-061072 Bucuresti
Tel. +40 / 314 25 09 09
Telefax +40 / 314 25 09 10

Saudi Arabia
Burgmann
Saudi Arabia Limited
PO box No. 3422,
Dammam Port Road
Dammam, Saudi Arabia
Phone +96 / 63 / 8 59 91 19
Telefax +96 / 63 / 8 59 92 29

Turkey
EagleBurgmann
Endstryiel Szdrmazlk
San. Ve Tic. Ltd. Sti.
S.S. stanbul Kimya Sanayiciler
Toplu yeri Yap Kooperatifi
E Blok No. 4
TR-81720 Teperen-Tuzla/Istanbul
Phone +90 / 216 / 5 93 02 93
Telefax +90 / 216 / 5 93 02 98

Tunisia
Indus Serv S.A.R.L
69 Rue Houcine Bouzaiene
Apt. N4, 2 me Etage
1001 Tunis
Phone +216 / 71/ 337 215
Telefax +216 / 71/ 337 214

Burgmann Industries
GmbH & Co. KG
uere Sauerlacher Str. 610
D-82515 Wolfratshausen
Germany
Phone +49(0)8171/23-0
Telefax +49(0)8171/23-1214
www.eagleburgmann.com
All technical specifications are based on extensive tests and our many years of
experience. The diversity of possible applications means, however, that they can
serve only as guide values. We must be notified of the exact conditions of application
before we can provide any guarantee for a specific case. Subject to change.

58E / E5 / 3.000 / 08.08 / 9.2.1 EagleBurgmann Marketing Communications Germany

Argentina
EagleBurgmann Argentina
Catalina M. de Boyle, 3117 (Calle 28)
San Martin - Buenos Aires
Phone +54 11 47 54 63 50
Fax +54 11 47 54 63 73