Eme

EME 2066 Measurement and Instrumentation, Trim.
3, 2014-2015
Tutorial 5
* Q1-5 to discuss in the class. Q6-10, take home and submit one week later.
1) A resistance-temperature detector (RTD) has (20C) = 0.004/C satisfying the equation:
R(T) = R(To)[1 + (T To)]
i. If the RTD has a resistance of 106 at 20C, find its resistance at 25C. [108.12]
ii. Assume the RTD has a dissipation constant of 25mW/C and is used in a circuit that puts
8mA through the sensor. If the RTD is placed in a bath at 100C,
a. what resistance will the RTD have?
[139.92]
b. what then is the indicated temperature?
[100.36C]
2) For a certain thermistor = 3420K and the resistance at 200F is known to be 1010. The
thermistor is used for a temperature measurement and the resistance is measured as 2315.
Calculate the temperature.
[146.14oF]
3) A radiant energy measurement is made to determine the temperature of a hot block of metal.
The emitted energy from the surface of the metal is measured as 28 kW/m 2 and the surface
emissivity is estimated as = 0.9. Calculate the surface temperature of the metal. What is the
emissive power of a blackbody at the same temperature? Find the error in the temperature if
an apparent blackbody temperature is taken as the measured value.
[860.7K, 31.11 kW/m2, 2.6%]
4) A thermometer having an emissivity of 0.9 is placed in a large room and indicates a
temperature of 25C. The walls of the room are at 35C and the convection heat transfer
coefficient is 5.0 W/m2.C. Calculate the true temperature of the air.
[13.63C]
5)
A
Known
Unknown
Insulation
Thermocouples
Heat Source
An apparatus shown in Fig. 1 is to be used to measure the

thermal conductivity of a sample B having an approximate
value of k = 15 W/m.C. The standard metal A used for
comparison has k = 69 W/m.C. If sample and standard both
have nominal lengths of 10cm, calculate the heat flux for an
overall temperature difference of 25C. If another sample is
connected in between, what is the thermal conductivity k of
the sample if the heat flux reduces by 20%.
[3080W/m2, 49.26 W/m.C]

Heat Sink
Fig. 1
6) A copper sphere 2.5cm in diameter is used as a slug type heat flux meter. A thermocouple is
attached to the indicator and the transient temperature recorded when the sphere is suddenly
exposed to a convection environment with h = 570 W/m2.C. Assume the sphere is initially at
95C and the environment temperature remains constant at 35C. What is the time constant
EME 2066 Measurement and Instrumentation, Trim.3, 2014-2015
of this system? Find the temperature after 15s. (copper = 8890 kg/m3, specific heat = 398
J/kg.C)
[25.86s, 68.59oC]
7) The thermal conductivity of an insulating material is to be determined using a guarded hot
plate apparatus. A 30 30 cm sample is used and a differential-thermocouple arrangement is
used to measure the temperature drop across the sample. A heat input of 5kW is supplied,
with a resulting temperature drop of 55C. If the sample thickness is 2.0mm, what is the
thermal conductivity? Assume no heat losses.
[2.02 W/m.C]
8) A capillary tube apparatus is to be used for measuring viscosities of oils with =0.001 kg/m.s
and =890 kg/m3. The design Reynolds number is 500. Calculate the length of a 1 mm
diameter tube that produces a pressure drop of 40kPa.
[2.22m]
9) A Saybolt viscometer is used to measure the viscosity of certain oil. The time for drainage of
the standard 60 ml sample is 1001 s. Calculate the kinematic and dynamic viscosities of oil
if the density is 880 kg/m3. Find the % uncertainties of the viscosities.
[ 2.022 105 m2 / s , 1.18%, 0.018 kg/m.s, 1.16% ]
10) A slug type heat-flux sensor has U = 0.1 W/m2.C. The slug is a copper cube 5 mm on a side
embedded in a wall. What heat flux would be necessary to produce a rise in temperature of
the sensor of 100C in a time of 30s? Given copper = 8890 kg/m3 and ccopper = 398 J/kg.C.
[58965.3 W/m2]
Review questions?
1.
What is temperature? Conversion between different temperature scales.
2.
What are the heat transfer modes?
3.
What are the possible ways of measuring temperature?
4.
What is temperature measurement by mechanical effect? Name a few.
5.
What is temperature measurement by electrical effect? Name a few.
6.
What is temperature measurement by radiation effect? Name a few.
7.
What are the differences between thermocouples, thermistors and RTDs?
8.
What is thermal radiation? What is a black body? Calculation of emissive power, total thermal radiation of a
blackbody and emissivity.
9.
States the equations for conduction, convection and radiation heat transfers.
10. What is thermal conductivity and how does one measure thermal conductivity in metals and fluids?
11. What is dynamic viscosity? What is kinematic viscosity? How is it measured?
12. What is gas diffusion?
13. What is calorimetry and calorimeter?
14. What are free- and forced- convection? Calculation of free convection and forced convection.
15. What is heat flux and how do we measure it?
16. What is pH measurement?

Eme

Uploaded by

Copyright:

Available Formats

Eme

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Eme

Uploaded by

Copyright:

Available Formats

EME 2066 Measurement and Instrumentation, Trim.

An apparatus shown in Fig. 1 is to be used to measure the

[3080W/m2, 49.26 W/m.C]

EME 2066 Measurement and Instrumentation, Trim.3, 2014-2015

What is temperature? Conversion between different temperature scales.

What are the heat transfer modes?

What are the possible ways of measuring temperature?

What is temperature measurement by mechanical effect? Name a few.

What is temperature measurement by electrical effect? Name a few.

What is temperature measurement by radiation effect? Name a few.

What are the differences between thermocouples, thermistors and RTDs?

You might also like