Water Rocket Manual

Everything You Ever Wanted to Know About Water Rockets and Launchers
Home

Why Water Rockets

How They Work
Bottle Profiles for Fins
Blog
Privacy Policy
Safety
Contact

Free Water
Rocket and
Launcher Plans
Get your free detail plans
for a water rocket with fin
templates, and a launch
tube type launcher with a
Clark cable tie release
complete with parts list,
and detailed step-by-step
instructions anyone can
follow. Instructions for
downloading will be
emailed immediately after
submitting the form below.
*Email

* First Name
open in browser PRO version

Gallery

How Bottle Rockets Work

The intricate details of the math and science of water rockets is reserved for a
chapter in volume 2 of The Complete Water Rocket Manual but a brief
explanation is in order before we get into building your first water rocket and
launcher.
A water rocket uses the same physics as a model rocket or the Shuttle launch
vehicle. Very simply, a rocket engine uses high pressure to force a fluid through a
restricted opening at a high velocity and this creates a force that propels the
launch vehicle in the opposite direction from the exhausting fluid.
Technically, a fluid is either a gas or a liquid. In chemical rockets, the fluid is a
superheated gas generated from a burning fuel. In a water rocket, the
temperatures are normally near outside temperatures and the fluid is a
combination of gas and liquid, the gas being normally air (although carbon dioxide,
or nitrogen are also sometimes used and a hydrogen-oxygen mix is used for a
hydrogen rocket) and the liquid being water (though it could be mixed with salt or
bubble bath or other ingredients).

Are you a developer? Try out the HTML to PDF API

pdfcrowd.com

* First Name

It is Newtons laws at work and especially his third law of motion simply stated as
Every action has an equal and opposite reaction.

*Last Name

Five Phases of Flight

A bottle rocket has four or five phases of flight as opposed to three for chemical
rockets.

= Required Field
Submit

1. Acceleration due to pressure acting against the launch tube. (This is not
A fter submitting your nam e
and e m ail addre ss, you will
re ce ive a confirm ation e m ail.
You m ust re spond to the
e m ail to ve rify that the e m ail
is corre ct and valid and to
confirm that it is you
re que sting the inform ation.
Afte r confirm ing your e m ail,
you will re ce ive a se cond e m ail
with download instructions for
the inform ation you are
re que sting. W e will only k e e p
your e m ail addre ss to le t you
k now whe n the com ple te
m anual is available an rare ly
if e ve r any othe r e m ails from
us.

Privacy Policy
Your information is never
shared with anyone
else...ever!
Once you have
downloaded and looked
over the free instructions,
why not visit my blog and

open in browser PRO version

2.
3.
4.

5.

present if a launch tube is not used)

Acceleration due to the reaction force of the water being ejected.
Acceleration due to the reaction force of the air being ejected.
Coast phase (ending at apogee, the highest altitude reached), which is the
longest part of the upward flight. The acceleration phases using just the
open neck of the bottle as the nozzle are in milliseconds.
The recovery phase where the rocket returns to earth after reaching
apogee.

Optimum Amount of Water to Use.

"How much water should I put in mhy water rocket?" That is a frequently asked
question. The amount of water used in the rocket makes a huge difference in the
altitude reached. Actually, using no water at all but simply using the compressed
air for thrust can propel an aerodynamically efficient water rocket to surprising
altitudes.
If you put too much water in, then the thrust available must loft more weight,
which reduces the maximum altitude. An air only rocket can fly higher than one
with too much water.
If too little water is used, then there isnt enough reaction mass to propel the
rocket most efficiently. The exact most efficient amount of water varies

Are you a developer? Try out the HTML to PDF API

pdfcrowd.com

why not visit my blog and

let me know what you
think...
Click here to go to my blog.
Also, if you haven't
already, visit my amateur
rocketry website here
where you can learn how
to build your own rocket
motor from PVC pipe with
sugar and potassium
nitrate KNO3) propellant
called caramel candy
propellant or rcandy (for
rocket candy).

open in browser PRO version

depending on the overall empty weight of the rocket and whether or not a launch
tube is used. The graph below shows a 2 liter bottle rocket weighing 150 grams
and 250 grams, using a launch tube and not, and with a fairly large drag
coefficient for an example. For this rocket, the optimal amount of water with a
launch tube is 22% for 150-gram rocket weight, 30% for a 250-gram, and without
a launch tube is 29% for 150-gram one, and 37% for a 250-gram rocket.
So you can see that the more the rocket weighs, the more water it needs to
reach the maximum altitude and the longer the launch rod, the less water it
needs. Also notice that with a launch tube, actually the heavier rocket reaches a
higher altitude. That is because by using the pressure working against the launch
tube, the launch tube can impart a greater momentum so the inertia will carry it
farther. It combines the affect of a bullet in a gun and a rocket motor. You can
find more details on this in the Science and Math chapter.

Are you a developer? Try out the HTML to PDF API

pdfcrowd.com

There are other factors involved any reasons why you may want more than
the optimum amount of water. This and many other topics are covered in

The Complete Water Rocket Manual

volumes 1 & 2
open in browser PRO version

Are you a developer? Try out the HTML to PDF API

pdfcrowd.com

...coming very soon. Order your free sample by filling in the form at the top
of this page on the left or send an email to
[email protected]

Ho w a L a u n c h e r Wo rk s
The Basics
The minimum requirements for a launcher are:
A way to pressurize the bottle
A seal to hold the water and pressure in the bottle until it is launched
A way to keep the rocket from launching until there is enough pressure
As stated before, there are as many designs for launchers as people using them.
However, if we just consider the most common and popular launcher types, we
can divide them into these categories:

Hand Held
Friction Plugs
Latched
Launch Tubes

Hand Held
A hand held launcher is sealed some way, usually an o-ring, and is held on the
launcher by hand as pressure is increased by an air pump. To launch, the person
holding the bottle on the launcher merely lets go.
open in browser PRO version

Are you a developer? Try out the HTML to PDF API

pdfcrowd.com

Friction Plugs
These are the simplest form of launcher and are comprised simply of a cork or
rubber stopper with a tube through it or a tire valve plugging the nozzle throat
whether it is just the bottle neck or a hole in a cap. A tire pump or pressurized
gas supply is attached directly to the tube or tire valve or indirectly with a longer
hose. The bottle is then pressurized and at some point where the pressure in the
bottle overcomes the friction fit, the plug is blown out of the bottle and the
bottle is launched.
Although this is the simplest method, the pressure at which the plug is blown out
is very unpredictable. It could happen at 30 psi or 200 psi (which is likely to burst
the bottle).
A rocket that is sitting flat on the ground on its fins may launch straight but may
not. Any irregularities in thrust, off centered center of gravity, or nonsymmetrical features on the outside of the rocket such as non-identical fins or
adhesive can affect the initial direction the rocket will fly. For consistency an
external guide rod will be required to insure a straight flight. A guide rod guides
the rocket straight in the first few feet of its flight until the air flow over the fins
is sufficient for them to take over that job.

Latched
The latched type of launcher overcomes the unpredictability of the friction plug
type by holding the bottle securely until it is ready to launch. When the desired
pressure is reached (assuming a pressure gage is in the system), the bottle is
unlatched and launches. As with the friction plug, this kind of launcher still needs
an external guide rod for a stable flight.

Launch Tube
open in browser PRO version

Are you a developer? Try out the HTML to PDF API

pdfcrowd.com

The launch tube fits through the neck of the bottle almost to the top of the
bottle on the inside. The launch tube system in its simplest form can be made
without a latch but it has to have a seal, usually an o-ring. The more common
launch tube launchers also have a latch that is remotely tripped. Either way, it
overcomes both problems. It is launched when desired rather than at a random
point and the launch tube, which runs up inside the bottle, guides the rocket
straight eliminated the need for an external guide. It also adds considerable
additional velocity and so higher maximum altitude.
The Simplest Launch Tube Launcher Hand Held
The simplest launch tube launcher without a latch actually does have a latch
you. One person can pump while another holds the rocket on the launch tube.
For one person use, a foot pump, electric compressor or gas cylinder could be
used. A compressor would have to be protected from the water.
When ready to launch, the person holding on to the rocket simply lets go. This
should only be used at lower pressures far below the burst pressure of the bottle,
40 to 50 psi max. This launcher should also be tall enough so that the bottle is
overhead just in case the bottle does burst, the person holding it is out of the
way of the blast. In the case of children, different heights of launch tubes
would have to be made for the different heights of the kids.
Kids especially may enjoy this because the person holding the bottle DEFINITELY
GET WET! This can be a big source of fun and laughter besides being a very
simple launcher to build.
C opyright: 2 0 1 2 J ac obs O nline, L L C

open in browser PRO version

Are you a developer? Try out the HTML to PDF API

pdfcrowd.com