Voltage Reg Apps

Linear & Switching Voltage Regulator
Applications Information
In Brief . . .
In most electronic systems, voltage regulation is required
for various functions. Todays complex electronic systems are
requiring greater regulating performance, higher efficiency
and lower parts count. Present integrated circuit and power
package technology has produced IC voltage regulators
which can ease the task of regulated power supply design,
provide the performance required and remain cost effective.
Available in a growing variety, Motorola offers a wide range of
regulator products from fixed and adjustable voltage types to
specialfunction and switching regulator control ICs.
This handbook describes Motorolas voltage regulator
products and provides information on applying these
products. Basic Linear regulator theory and switching
regulator topologies have been included along with practical
design examples. Other relevant topics include tradeoffs of
Linear versus switching regulators, series pass elements for
Linear regulators, switching regulator component design
considerations, heatsinking, construction and layout, power
supply supervision and protection, and reliability.
Page
Basic Linear Regulator Theory . . . . . . . . . . . . . . . . . . . 3820
Selecting a Linear IC Voltage Regulator . . . . . . . . . . . 3829
Linear Regulator Circuit Configuration
and Design Considerations . . . . . . . . . . . . . . . . . . . . 3832
Series Pass Element Considerations
for Linear Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . 3843
Linear Regulator Construction and Layout . . . . . . . . . 3851
Linear Regulator Design Example . . . . . . . . . . . . . . . . 3873
Linear Regulator Circuit Troubleshooting
Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3876
Designing the Input Supply . . . . . . . . . . . . . . . . . . . . . . 3877
An Introduction to Switching
Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3883
Switching Regulator Topologies . . . . . . . . . . . . . . . . . . 3888
Switching Regulator Component
Design Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3896
Basic Switching Power Supply
Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3900
Switching Regulator Design Examples . . . . . . . . . . . . 3908
Power Supply Supervisory and
Protection Considerations . . . . . . . . . . . . . . . . . . . . . 3909
Heatsinking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3917
MOTOROLA ANALOG IC DEVICE DATA
3817
TABLE OF CONTENTS
Section 1.
Basic Linear Regulator Theory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

IC Voltage Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Error Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Regulator within a Regulator Approach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page
3820
3820
3820
3824
3827
Section 2.
Selecting a Linear IC Voltage Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Selecting the Type of Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Positive versus Negative Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ThreeTerminal, Fixed Output Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ThreeTerminal, Adjustable Output Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting an IC Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3829
3829
3829
3829
3831
3831
Section 3.
Linear Regulator Circuit Configuration and Design Considerations . . . . . . . . . . . . . . . . . . . . . . .

Positive, Adjustable Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Negative, Adjustable Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Positive, Fixed Output Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Negative, Fixed Output Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Design Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3832
3832
3836
3836
3839
3841
Section 4.
Series Pass Element Considerations for Linear Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Series Pass Element Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Series Pass Element Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current Limiting Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Constant Current Limiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Foldback Current Limiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Paralleling Series Pass Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3843
3843
3844
3845
3845
3848
3850
Section 5.
Linear Regulator Construction and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General Layout and Component Placement Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ground Loops and Remote Voltage Sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting Considerations for Power Semiconductors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insulation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fastener and Hardware Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal System Evaluation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix A: Thermal Resistance Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix B: Measurement of Interface Thermal Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3851
3851
3851
3853
3857
3861
3869
3870
3871
Section 6.
Linear Regulator Design Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

IC Regulator Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Determination of Component Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Determination of Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selection of Series Pass Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q1 Heatsink Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clamp Diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Construction Input Supply Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3873
3873
3873
3873
3874
3874
3875
3875
3875
Section 7.
Linear Regulator Circuit Troubleshooting Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3876
3818
TABLE OF CONTENTS (Continued)

Page
Section 8.
Designing the Input Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Design of CapacitorInput Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Surge Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Design Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Design Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3877
3878
3880
3881
3882
Section 9.
An Introduction to Switching Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Comparison with Linear Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Future . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3883
3883
3884
3886
Section 10.
Switching Regulator Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

FET and Bipolar Drive Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overvoltage Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Surge Current Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transformer Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filter Capacitor Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3888
3888
3890
3891
3892
3892
3894
Section 11.
Switching Regulator Component Design Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Transistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Zener and Mosorb Transient Suppressors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rectifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3896
3896
3898
3898
Section 12.
Basic Switching Power Supply Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Flyback and Forward Converters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PushPull and Bridge Converters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Half and Full Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3900
3900
3903
3906
Section 13.
Switching Regulator Design Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3908
Section 14.
Power Supply Supervisory and Protection Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The Crowbar Technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCR Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Sense and Drive Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MC3425 Power Supply Supervisory Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MC34064 and MC34164 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3909
3909
3910
3911
3914
3916
Section 15.
Heatsinking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Thermal Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a Heatsink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Commercial Heatsinks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Custom Heatsink Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heatsink Design Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SOIC Miniature IC Plastic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal Characteristics of SOIC Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SOP8 and SOP16L Packaged Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal Characteristics of DPAK and D2PAK Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3917
3917
3918
3918
3920
3923
3923
3924
3924
3925
3819
SECTION 1
BASIC LINEAR REGULATOR THEORY
A. IC Voltage Regulator
The basic functional block diagram of an integrated circuit voltage regulator is shown in Figure 11.
It consists of a stable reference, whose output voltage is Vref, and a high gain error amplifier. The output
voltage (VO), is equal to or a multiple of Vref. The regulator will tend to keep VO constant by sensing any
changes in VO and trying to return it to its original value. Therefore, the ideal voltage regulator could be
considered a voltage source with a constant output voltage. However, in practice the IC regulator is better
represented by the model shown in Figure 12.
In this figure, the regulator is modeled as a voltage source with a positive output impedance (ZO). The
value of the voltage source (V) is not constant; instead it varies with changes in supply voltage (VCC) and
with changes in IC junction temperature (TJ) induced by changes in ambient temperature and power
dissipation. Also, the regulator output voltage (VO) is affected by the voltage drop across ZO, caused by
the output current (IO). In the following text, the reference and amplifier sections will be described, and their
contributions to the changes in the output voltage analyzed.
B. Voltage Reference
Naturally, the major requirement for the reference is that it be stable; variations in supply voltage or
junction temperature should have little or no effect on the value of the reference voltage (Vref).
1. Zener Diode Reference

The simplest form of a voltage reference is shown in Figure 13a. It consists of a resistor and a zener
diode. The zener voltage (VZ) is used as the reference voltage. In order to determine VZ, consider Figure
13b. The zener diode (VR1) of Figure 13a has been replaced with its equivalent circuit model and the
value of VZ is therefore given by (at a constant junction temperature):
VZ = VBZ + IZZZ = VBZ +
VCC VBZ
R + Zz
ZZ
(1)
where: VBZ = zener breakdown voltage

IZ = zener current
ZZ = zener impedance at IZ.
Note that changes in the supply voltage give rise to changes in the zener current, thereby changing the
value of the reference voltage (VZ).
3820
Figure 11. Voltage Regulator Functional Block Diagram

VCC
Reference
Error
Amplifier
Vref
VO
Figure 12. Voltage Regulator Equivalent Circuit Model

VCC
ZO
IO
VO
V = f (VCC, Tj)
Figure 13. Zener Diode Reference

VCC
VCC
R
IZ
R
VZ
VR1
(a)
VZ
ZZ
VBZ
(b)
3821
2. Constant Current Zener Reference

The effect of zener impedance can be minimized by driving the zener diode with a constant current as
shown in Figure 14. The value of the zener current is largely independent of VCC and is given by:
IZ =
VBEQ1
RSC
(2)
where: VBEQ1 = baseemitter voltage of Q1.

This gives a reference voltage of:
Vref = VZ + VBEQ1 = VBZ + IZZZ + VBEQ1
(3)
where IZ is constant and given by Equation 2.

The reference voltage (about 7.0 V) of this configuration is therefore largely independent of supply voltage
variations. This configuration has the additional benefit of better temperature stability than that of a simple
resistorzener reference.
Referring back to Figure 13a, it can be seen that the reference voltage temperature stability is equal
to that of the zener diode, VR1. The stability of zener diodes used in most integrated circuitry is about
+ 2.2 mV/C or
0.04%/C (for a 6.2 V zener). If the junction temperature varies 100C, the zener or
reference voltage would vary 4%. A variation this large is usually unacceptable.
However, the circuit of Figure 14 does not have this drawback. Here the positive 2.2 mV/C
temperature coefficient (TC) of the zener diode is offset by the negative 2.2 mV/C TC of the VBE of Q1.
This results in a reference voltage with very stable temperature characteristics.
Figure 14. Constant Current (Zener Reference)

VCC
R
Q2
Vref
VZ
VR1
IZ
Q1
VBEQ1
3822
RSC
3. Bandgap Reference
Although very stable, the circuit of Figure 14 does have a disadvantage in that it requires a supply
voltage of 9.0 V or more. Another type of stable reference which requires only a few volts to operate was
described by Widlar(1) and is shown in Figure 15. In this circuit Vref is given by:
Vref = VBEQ3 + I2R2
where:
I2 =
VBEQ1 VBEQ2
R1
(4)
(neglecting base currents)
The change in Vref with junction temperature is given by:

Vref = VBE3 +
VBEQ1 VBEQ2
R2
R1
(5)
It can be shown that,

VBEQ1 = TJK ln I1
(6)
and, VBEQ2 = TJK ln I2
(7)
where:
K = a constant
TJ = change in junction temperature
and,
I1 > I2
Combining (5), (6), and (7)

Vref = VBEQ3 + TJK
R2
R1
ln
I1
I2
(8)
Since VBEQ3 is negative, and with I1 > I2, ln I1/I2 is positive, the net change in Vref with temperature
variations can be made to equal zero by appropriately selecting the values of I1, R1, and R2.
Figure 15. Bandgap Reference
VCC
Vref
I1
R3
R2
I2
Q3
Q1
VBEQ1
VBEQ3
Q2
VBEQ2
R1
3823
C. The Error Amplifier

Given a stable reference, the error amplifier becomes the determining factor in integrated circuit
voltage regulator performance. Figure 16 shows a typical differential error amplifier in a voltage regulator
configuration. With a constant supply voltage (VCC) and junction temperature, the output voltage is
given by:
VO= AVOL i ZOL IO = AVOL {(Vref VIO) VO } ZOL IO
where:
(9)
AVOL = amplifier open loop gain

VIO = input offset voltage
ZOL = open loop output impedance
R1
=
= feedback ratio ( is always 1)
R1 + R2
IO = output current
i= true differential input voltage

Manipulating Equation 9:
Z
(Vref VIO) OL IO
AVOL
VO =
1
+
AVOL
(10)
Note that if the amplifier open loop gain is infinite, this expression reduces to:
1
VO =
(Vref VIO) = (Vref VIO) 1
R2
R1
(11)
The output voltage can thus be set any value equal to or greater than (Vref VIO). Note also that if AVOL is not
infinite, with constant output current (a nonvarying output load), the output voltage can still be
tweakedin by varying R1 and R2, even though VO will not exactly equal that given by Equation 11.
Assuming a stable reference and a finite value of AVOL, inaccuracy of the output voltage can be traced
to the following amplifier characteristics:
1. Amplifier Input Offset Voltage Drift

The input transistors of integrated circuit amplifiers are usually not perfectly matched. As in operational
amplifiers, this is expressed in terms of an input offset voltage (VIO). At a given temperature, this effect can
be nulled out of the desired output voltage by adjusting Vref or 1/. However, VIO drifts with temperature,
typically 5.0 V/C to +15 V/C, causing a proportional change in the output voltage. Closer matching of
the internal amplifier input transistors minimizes this effect, as does selecting a feedback ratio () to be
close to unity.
2. Amplifier Power Supply Sensitivity

Changes in regulator output voltage due to power supply voltage variations can be attributed to two
amplifier performance parameters: power supply rejection ratio (PSRR) and common mode rejection ratio
(CMRR). In modern integrated circuit regulator amplifiers, the utilization of constant current sources gives
such large values of PSRR that this effect on VO can usually be neglected. However, supply voltage
changes can affect the output voltage since these changes appear as common mode voltage changes, and
they are best measured by the CMRR.
3824
Figure 16. Typical Voltage Regulator Configuration

VCC
(+)
+VIO
Vref
IO
ZOL
VO
AVOLi
()
R2
R1
))
The definition of common mode voltage (VCM), illustrated by Figure 17a, is:
VCM
where:
V1
) V2
2
(V )
(V)
(12)
V1 = voltage on amplifier noninverting input

V2 = voltage on amplifier inverting input
V+ = positive supply voltage
V = negative supply voltage
Figure 17. Definition of Common Mode Voltage Error

V+
V+
V1
V1
+
VCM
CMRR
+
VO
V2
AVOLi
V2
VO
(a)
(b)
3825
Figure 18. Common Mode Regulator Effects

VCC
(+)
VCM
CMRR
Vref
VO
AVOLi
()
R2
R1
In an ideal amplifier, only the differential input voltage (V1 V2) has any effect on the output voltage; the
value of VCM would not effect the output. In fact, VCM does influence the amplifier output voltage. This effect
can be modeled as an additional voltage offset at the amplifier input equal to VCM/CMRR as shown in
Figures 17b and 18. The latter figure is the same configuration as Figure 16, with amplifier input offset
voltage and output impedance deleted for clarity and common mode voltage effects added. The output
voltage of this configuration is given by:
VCM
VO= AVOL i = AVOL Vref
bVO
CMRR
Manipulating,
VO =
where:
and,
VCM
CMRR
+ 1
AVOL
Vref
VCC
VCM = Vref
2
(13)
(14)
(15)
CMRR = common mode rejection ratio
It can be seen from Equations (14) and (15) that the output can vary when VCC varies. This can be reduced
by designing the amplifier to have a high AVOL, a high CMRR, and by choosing the feedback ratio () to
be unity.
3826
3. Amplifier Output Impedance

Referring back to Equation (9), it can be seen that the equivalent regulator output impedance (ZO) is
given by:
ZO =
VO
IO
ZOL
AVOL
(16)
This impedance must be as low as possible, in order to minimize load current effects on the output voltage.
This can be accomplished by lowering ZOL, choosing an amplifier with high AVOL, and by selecting the
feedback ratio () to be unity.
A simple way of lowering the effective value of ZOL is to make an impedance transformation with an
emitter follower, as shown in Figure 19. Given a change in output current (IO) the amplifier will see a
change of only IO/hFEQ1 in its output current (IO ). Therefore, (ZOL) in Equation (16) has been effectively
reduced to ZOL/hFEQ1, reducing the overall regulator output impedance (ZO).
D. The Regulator within a Regulator Approach

In the preceding text, we have analyzed the sections of an integrated circuit voltage regulator and
determined how they contribute to its nonideal performance characteristics. These are shown in Table
11 along with procedures which minimize their effects.
It can be seen that in all cases regulator performance can be improved by selecting AVOL as high as
possible and = 1. Since a limit is soon approached in how much AVOL can be practically obtained in an
integrated circuit amplifier, selecting a feedback ratio () equal to unity is the only viable way of improving
total regulator performance, especially in reducing regulator output impedance. However, this method
presents a basic problem to the regulator designer. If the configuration of Figure 16 is used, the output
voltage cannot be adjusted to a value other than Vref. The solution is to utilize a different regulator
configuration known as the regulator within a regulator approach.(2) Its greatest benefit is in reducing total
regulator output impedance.
Figure 19. Emitter Follower Output
VCC
(+)
Vref
ZOL
IO
Q1
IO
VO
()
R2
R1
3827
Table 11
VO Changes
Section
Effect Can Be
Induced By:
Minimized By Selecting:
VCC
Constant currentzener method

Bandgap reference
TJ
Bandgap reference
TC compensated zener method
Reference
Amplifier
VCC
High CMRR amplifier

High AVOL amplifier
=1
TJ
Low VIO drift amplifier

High AVOL amplifier
=1
IO
Low ZOL amplifier

High AVOL amplifier
Additional emitter follower output
=1
)
] )
As shown in Figure 110, amplifier A1 sets up a voltage (V1) given by:

V1
] Vref
R2
R1
(17)
V1 now serves as the reference voltage for amplifier A2, whose output voltage (VO) is given by:
VO
] V1
Vref
R2
R1
(18)
Note that the output impedance of A2, and therefore the regulator output impedance, has been minimized
by selecting A2s feedback factor to be unity; and that output voltage can still be set at voltages greater than
Vref by adjusting R1 and R2.
Figure 110. The Regulator within a Regulator Configuration
ZOL
A2
+
Vref
VO
V1
A1
R2
R1
(1)Widlar, R. J., New Developments in IC Voltage Regulators, IEEE Journal of Solid State Circuits, Feb.1971, Vol. SC6, pgs. 27.
(2)Tom Fredericksen, IEEE Journal of Solid State Circuits, Vol. SC3, Number 4, Dec. 1968, A Monolithic High Power Series Voltage Regulator.
3828
SECTION 2
SELECTING A LINEAR IC VOLTAGE REGULATOR
A. Selecting the Type of Regulator
There are five basic linear regulator types; positive, negative, fixed output, tracking and floating
regulators. Each has its own particular characteristics and best uses, and selection depends on the
designers needs and tradeoffs in performance and cost.
1. Positive Versus Negative Regulators

In most cases, a positive regulator is used to regulate positive voltages and a negative regulator
negative voltages. However, depending on the systems grounding requirements, each regulator type may
be used to regulate the opposite voltage.
Figures 21a and 21b show the regulators used in the conventional and obvious mode. Note that the
ground reference for each (indicated by the heavy line) is continuous. Several positive regulators could
be used with the same input supply to deliver several voltages with common grounds; negative regulators
may be utilized in a similar manner.
If no other common supplies or system components operate off the input supply to the regulator, the
circuits of Figures 21c and 21d may be used to regulate positive voltages with a negative regulator and
vice versa. In these configurations, the input supply is essentially floated, i.e., neither side of the input is
tied to the system ground.
There are methods of utilizing positive regulators to obtain negative output voltages without sacrificing
ground bus continuity. However, these methods are only possible at the expense of increased circuit
complexity and cost. An example of this technique is shown in Section 3.
2. ThreeTerminal, Fixed Output Regulators

These regulators offer the designer a simple, inexpensive way to obtain a source of regulated voltage.
They are available in a variety of positive or negative output voltages and current ranges.
The advantages of these regulators are:
a) Easy to use.
b) Internal overcurrent and thermal protection.
c) No circuit adjustments necessary.
d) Low cost.
Their disadvantages are:
a) Output voltage cannot be precisely adjusted. (Methods for obtaining adjustable outputs are shown
in Section 3).
b) Available only in certain output voltages and currents.
c) Obtaining greater current capability is more difficult than with other regulators. (Methods for
obtaining greater output currents are shown in Section 3.)
3829
Figure 21. Regulator Configurations
+
Input
Supply
Positive
Regulator
Vin
VO
(a) Positive Output Using Positive Regulator
Input
Supply
Vin
VO
Negative
Regulator
(b) Negative Output Using Negative Regulator
Input
Supply
Vin
VO
Negative
Regulator
(c) Positive Output Using Negative Regulator
+
Input
Supply
Positive
Regulator
Vin
VO
(d) Negative Output Using Positive Regulator
3830
3. ThreeTerminal, Adjustable Output Regulators

Like the threeterminal fixed regulators, the threeterminal adjustable regulators are easy and
inexpensive to use. These devices provide added flexibility with output voltage adjustable over a wide
range, from 1.2 V to nearly 40 V, by means of an external, tworesistor voltage divider. A variety of current
ranges from 100 mA to 3.0 A are available.
B. Selecting an IC Regulator
Once the type of regulator is decided upon, the next step is to choose a specific device. To provide
higher currents than are available from monolithic technologies, an IC regulator will often be used as a
driver to a boost transistor. This complicates the selection and design task, as there are now several
overlapping solutions to many of the design problems.
Unfortunately, there is no exact stepbystep procedure that can be followed which will lead to the
ideal regulator and circuit configuration for a specific application. The regulating circuit that is finally
accepted will be a compromise between such factors as performance, cost, size and complexity. Because
of this, the following general design procedure is suggested:
1. Select the regulators which meet or exceed the requirements for line regulation, load regulation, TC of
the output voltage and operating ambient temperature range. At this point, do not be overly concerned with
the regulator capabilities in terms of output voltage, output current, SOA and special features.
2. Next, select application circuits from Section 3 which meet the requirements for output current, output
voltage, special features, etc. Preliminary designs using the chosen regulators and circuit configurations
are then possible. From these designs a judgement can be made by the designer as to which regulator
circuit configuration combination best meets his or her requirements in terms of cost, size and complexity.
3831
SECTION 3
LINEAR REGULATOR CIRCUIT CONFIGURATION
AND DESIGN CONSIDERATIONS
Once the IC regulators, which meet the designers performance requirements, have been selected,
the next step is to determine suitable circuit configurations. Initial designs are devised and compared to
determine the IC regulator/circuit configuration that best meets the designers requirements. In this
section, several circuit configurations and design equations are given for the various regulator ICs.
Additional circuit configurations can be found on the device data sheets. Organization is first by regulator
type and then by variants, such as current boost. Each circuit diagram has component values for a
particular voltage and current regulator design.
A. Positive, Adjustable
B. Negative, Adjustable
C. Positive, Fixed
D. Negative, Fixed
E. Tracking
F. Special
1. Obtaining Extended Output Voltage Range
2. Electronic Shutdown
G. General Design Considerations
It should be noted that all circuit configurations shown have constant current limiting. If foldback limiting
is desired, see Section 4C for techniques and design equations.
A. Positive, Adjustable Output IC Regulator Configurations

1. Basic Regulator Configurations
Positive ThreeTerminal Adjustables
These adjustables, comprised of the LM317L, LM317, and LM350 series devices range in output
currents of 100 mA, 500 mA, 1.5 A, and 3.0 A respectively. All of these devices utilize the same basic circuit
configuration as shown in Figure 31A.
MC1723C
The basic circuit configurations for the MC1723C regulator are shown in Figures 32A and 33A. For
output voltages from 7.0 V to 37 V the configuration of Figure 32A can be used, while Figure 33A can
be used to obtain output voltages from 2.0 V to
7.0 V.
2. Output Current Boosting

If output currents greater than those available from the basic circuit configurations are desired, the
current boost circuits shown in this section can be used. The output currents which can be obtained with
this configurations are limited only by capabilities of the external pass element(s).
3832
Figure 31A. Basic Configuration for Positive, Adjustable Output

ThreeTerminal Regulators
Vin
+ VO
Vout
LM317L
LM317
LM350
R1
240
IAdj
Adjust
Cin
0.1F
CO
1.0F
CAdj
10F
R2
Cin: required if regulator is located an appreciable distance from power supply filter.
CO: improves transient response.
CAdj: improves Ripple Rejection.
R2
+ IAdj R2
Vout = 1.25 V 1 +
R1
Since IAdj is controlled to less than 100 A, the error
associated with this term is negligible in most applications.
Figure 32A. MC1723C Basic Circuit Configuration for Vref VO 37 V

Vin
+ 20V
12
10
11
RSC
VO
22
+ 15V
ISC = 30 mA
MC1723C
R3
5.1k
5
13
0.01F
12k
R1
10k
R2
4
100pF
Cref
7
RSC
0.66 V
; 10 k < R1 + R2 < 100 k
ISC
R3 R1 || R2 ; 0 Cref 0.1 F
R2 =
Vref
7.0 V
(R1 + R2)
(R1 + R2)
VO
VO
Values shown are for a 15 V, 30 mA regulator

using an MC1723CP for a TA(max) = 25C.
3833
Figure 33A. MC1723C Basic Circuit Configuration for 2.0 V VO Vref

Vin
+ 20V
12
10
11
RSC
VO
22
+ 5.0V
ISC = 30 mA
3
MC1723C
5.1k
5
R1
3.6k
R3
4
13
Cref
0.01F
R2
13k
1.0nF
7
RSC
0.66V
; 10 k < R1 + R2 < 100 k
ISC
VO
VO
(R1 + R2)
(R1 + R2)
Vref
7.0 V
R3 = R1 || R2; 0 Cref 0.1 F
R2 =
Values shown are for a 5.0 V, 30 mA regulator using

an MC1723CP for a TA(max) = 70C.
To obtain greater output currents with the MC1723C the configurations shown in Figures 34A and
35A can be used. Figure 34A uses an NPN external pass element, while a PNP is used in Figure 35A.
Figure 34A. MC1723C NPN Boost Configuration
Q1
2N3055
or Equiv
+ Vin
+ 20V
12
10
11
RSC
VO
1.3
1/2W
+ 15V
ISC = 0.5A
3
MC1723C
R3
5.1k
0.1F
13
R1
12k
R2
10k
100pF
Cref
7
0.66 V
; 10 k < R1 + R2 < 100 k
ISC
Vref
7.0 V
R2 =
(R1 + R2)
(R1 + R2)
VO
VO
RSC
0 Cref 0.1 F ; R3 R1 || R2
Selection of Q1 based on considerations of Section 4.
Values shown are for a 15 V, 500 mA regulator using an unheatsinked
MC1723CP and a 2N3055 on a 6C/W heatsink for TA up to + 70C.
3834
Figure 35A. MC1723C PNP Boost Configuration

2N3791
or Equiv
Vin
Q1
+ 18V
R4
100
11
10
12
RSC
VO
0.91
1/2W
+ 12V
ISC = 0.75 A
3
MC1723C
R3
5.1k
0.1F
13
R1
10k
100pF
Cref
R2
13k
7
0.66 V
; 10 k < R1 + R2 < 100 k ; 0 Cref 0.1 F
ISC
Vref
7.0 V
R2 =
(R1 + R2)
(R1 + R2)
VO
VO
RSC
R3 = R1 || R2
0 < R4 VBE
on (Q1)
/ 5.0 mA

Values shown are for a 12 V, 750 mA regulator using an unheatsinked
3. High Efficiency Regulator Configurations

When large output currents at voltages under approximately 9.0 V are desired, the configuration of
Figure 36A can be utilized to obtain increased operating efficiency. This is accomplished by providing a
separate low voltage input supply for the pass element. This method, however, usually necessitates that
separate short circuit protection be provided for the IC regulator and external pass element. Figure 36A
shows a high efficiency regulator configuration for the MC1723C.
Figure 36A. MC1723C High Efficiency Regulator Configuration
2N3055
Q1
Vin1
RSC
+ 6.5V
0.62
1.0W
Vin2
10
+ 10V
R = 15
IB
Cref
R1
2.0k
3
R2
5.1k
MC1723C
VO
+5.0V
ISC = 1.0 A
MPS6512 or
Equivalent
3
4
1.3k
13
R3
0.6 V
RSC
ISC
R
0.1F
1.0nF
See Section 3F for general design considerations.

0.66 V
; 10 k <R1 + R2 < 100 k
Ib(max)
VO
R2 =
Vref
VO
(R1 + R2)
(R1 + R2)
7.0 V
0 Cref 0.1 F
R3 R1 || R2
Values shown for a 5.0 V, 1.0 A regulator using an unheatsinked

3835
B. Negative, Adjustable Output IC Regulator Configurations

1. Basic Regulator Configurations (MC1723C)
Although a positive regulator, the MC1723C can be used in a negative regulator circuit configuration.
This is done by using an external pass element and a zener level shifter as shown in Figure 31B. It should
be noted that for proper operation, the input supply must not vary over a wide range, since the correct value
for VZ depends directly on this voltage. In addition, it should be noted that this circuit will not operate with
a shorted output.
Figure 31B. MC1723C Negative Regulator Configuration
10
12
11
R1
12k
4
MC1723C
6
+
100pF
10mF
13
R2
10k
7
VZ = 14 V
Vin = 20 V to 23 V
Q1
VO = 15 V
2N3055
or Equiv
VO 10 V; 10 k R1 + R2 100 k
Vref
7.0 V
R2 =
(R1 + R2)
(R1 + R2)
VO
VO
VZ Vin VBE(Q1) 3.0 V; VZ Vin VO VBE(Q1) + 6.0 V
Values shown are for a 15 V, 750 mA regulator using the MC1723CP with Q1
mounted on a 20C/W heatsink at TA up to +70C. Do not short circuit output.
C. Positive, Fixed Output IC Regulator Configurations

1. Basic Regulator Configuration
The basic current configuration for the positive threeterminal regulators is shown in Figure 31C.
Depending on which regulator type is used, this configuration can provide output currents in excess
of 3.0 A.
2. Output Current Boosting

Figure 32C illustrates a method for obtaining greater output currents with the threeterminal positive
regulators. Although any of these regulators may be used, usually it is most economical to use the 1.0 A
MC7800C in this configuration.
3836
Figure 31C. Basic Circuit Configuration for Positive, Fixed Output, ThreeTerminal Regulators
1
Vin
Cin
0.33F
IO
1.0 A
0.1 A
0.5 A
3.0 A
Device
MC78XX
MC78LXX
MC78MXX
MC78TXX
VO
CO
Cin: required if regulator is located more than a few (2 to 4) inches away

Cin: from input supply capacitor; for long input leads to regulator, up to 1.0 F
Cin: may be needed for Cin. (Cin should be a high frequency type capacitor.)
CO: improves transient response.
XX: two digits of type number indicating nominal output voltage.
See Section 15 for heatsinking.
Figure 32C. Current Boost Configuration for Positive ThreeTerminal Regulators

0.12
5.0W
Vin
10V
MJ2955
or Equiv
RSC
Q1
ISC(Q1)
2N6049
or Equiv
R
IC1
1
MC78XXC
ISCTOT
VO
5.0V
50
1.0F
ISC(IC1)

R: used to divert IC regulator bias current and determines at
what output current level Q1 begins conducting.
0<R
VBE on(Q1)
0.6 V
; RSC
; I
=I
+I
ISC(Q1) SCTOT SC(Q1) SC(IC1)
IBias (IC1)
Values shown are for a 5.0 V, 5.0 A regulator using an MC7805CT on

a 2.5C/W heatsink and Q1 on a 1C/W heatsink for TA up to 70C.
3. Obtaining an Adjustable Output Voltage

With the addition of an op amp, an adjustable output voltage supply can be obtained with the MC7805C.
Regulation characteristics of the threeterminal regulators are retained in this configuration, shown in
Figure 33C. If lower output currents are required, then an MC78M05C (0.5 A) could be used in place of
the MC7805C.
4. Current Regulator
In addition to providing voltage regulation, the threeterminal positive regulators can also be used as
current regulators to provide a constant current source. Figure 34C shows this configuration. The output
current can be adjusted to any value from 8.0 mA (IQ, the regulator bias current) up to the available output
current of the regulator. Fivevolt regulators should be used to obtain the greatest output voltage
compliance range for a given input voltage.
3837
Figure 33C. Adjustable Output Voltage Configuration

Using a ThreeTerminal Positive Regulator
Vin
VO
MC7805C
Figure 34C. Current Regulator Configuration
MC7805C
MC78MO5C
MC78L05A, C
Vin
0.33F
2
VO
Constant Current
VO
to Grounded Load
3
7
6
0.33F
IIB
2
0.1F
MC1741CP1
3
1.0k
IO =
10k
IO
VO
+ IIB
R
Current Reg IO =
VO
+ IIB
R
VO + VO + 2.0 V Vin 35 V
VO = 7.0 V to 33 V
Vin VO 2.0 V
Vin 35 V
5. High Input Voltage

Occasionally, it may be necessary to power a threeterminal regulator from a supply voltage greater
than Vin(max), 35 V or 40 V. In these cases a preregulator circuit, as shown in Figure 35C, may be used.
Figure 35C. Preregulator for Input Voltages Above Vin(max)
60V
R1
IC1
2N6569
Vin
1
Q1
750
2.0W
0.33F
MC78XXC
VO
IN5363
30V, 5.0W
Vin 30
) hfe(Q1)
1.5
VCEO(Q1) Vin
R1 = (

Values shown for Vin = 60 V
Q1 should be mounted on a 2C/W heatsink for operation at TA up to
+70C. IC1 should be appropriately heatsinked for the package type used.
6. High Output Voltage

If output voltages above 24 V are desired, the circuit configuration of Figure 36C may be used. Zener
diode (Z1) sets the output voltage, while Q1, Z2, and D1 assure that the MC7824C does not have more
than 30 V across it during short circuit conditions.
3838
Figure 36C. High Output Voltage Configuration for ThreeTerminal Positive Regulators
IC1
2N6576
Vin
60V
R1
VO
2
MC7824CT
48V
5.6k
1/2W
Q1
IN4751
30V,
1.0W
Z2
0.33F
10F
50V
IN4001
D1
IN4749
24V, 1.0W
Z1
VO = VZ1 + 24; R1 = (
Vin (VZ1 + VZ2)

) hfe(Q2)
1.5
Values shown are for a 48 V, 1.0 A regulator

Q1 mounted on a 10C/W heatsink
and IC1 mounted on a 2C/W heatsink for TA up to +70C.
D. Negative, Fixed Output IC Regulator Configurations

1. Basic Regulator Configurations
Figure 31D gives the basic circuit configuration for the MC79XX and MC79LXX threeterminal
negative regulators.
Figure 31D. Basic Circuit Configuration for Negative ThreeTerminal Regulators
Vin
Cin
Cin:
Cin:
Cin:
CO:
XX:
3 or
Case
IO
1.0 A
0.1 A
Device
MC79XX
MC79LXX
0.33F
2
VO
0.1F
CO
required if regulator is located more than a few ( 2 to 4) inches away from input supply
capacitor; for long input leads to regulator, up to 1.0 F may be required. Cin should be a high frequency type
capacitor.
improves stability and transient response.
two digits of type number indicating nominal output voltage.
See Section 15 for heatsinking.
3839
Output Current Boosting

In order to obtain increased output current capability from the negative threeterminal regulators, the
current boost configuration of Figure 32D may be used. Currents which can be obtained with this
configuration are limited only by the capabilities of the external pass transistor(s).
Figure 32D. Output Current Boost Configuration for ThreeTerminal Negative Regulators
ISC(Q1)
0.56, 1W
10V
Vin
0.56, 1W
RSC
Q1
0.56, 1W
ISCTOT
VO
2N3055
or Equiv
ISC(IC1)
IC1
MJE200
or Equiv
MC79XXC
R
5.6
1.0F
1.0F
Gnd
Gnd
XX: two digits of type number indicating output voltage. See Section 2 for available voltages.
R: used to divert regulator bias current and determine at what output current level Q1
R: begins conducting.
O<R
VBE on(Q1)
IBias(IC1)
ISCTOT = ISC(Q1) + ISC(IC1)

RSC
0.6 V
ISC(Q1)
Values shown are for a 5.0 V, +4.0 A regulator; using an MC7905CT on a 1.5C/W heatsink
with Q1 mounted on a 1C/W heatsink for TA up to +70C.
2. Current Regulator
The threeterminal negative regulators may also be used to provide a constant current sink, as shown
in Figure 33D. In order to obtain the greatest output voltage compliance range at a given input voltage,
the MC7905C or MC79L05C should be used in this configuration.
Figure 33D. Current Regulator Configuration for the ThreeTerminal Negative Regulators
Constant Current
from Grounded
VO Load
IO
Vin
MC7905C
or
MC79L05A,C
1.0F
VO
1.0F
IIB
Vin 35 V for MC7905C
Vin 30 V for MC79L05C
Vin VO + VO 2.0 V
IO =
VO
+ IIB
R
Current regulation: IO =
3840
VO
+ IIB
R
F. General Design Considerations

In addition to the design equations given in the regulator circuit configuration panels of Sections 3AE,
there are a few general design considerations which apply to all regulator circuits. These considerations
are given below.
1. Regulator Voltages
For any circuit configuration, the worsecase voltages present on each pin of the IC regulator must be
within the maximum and/or minimum limits specified on the device data sheets. These limits are
instantaneous values, not averages.
They include: a. Vin(min)
b. Vin(max)
c. (Vin Vout) min
d. Vout(min)
e. Vout(max)
For example, the voltage between Pins 12 and 7 (Vin) of an MC1723CP must never fall below 9.5 V,
even instantaneously, or the regulator will not function properly, (see Figure 31B).
2. Regulator Power Dissipation, Junction Temperature and Safe Operating Area

The junction temperature, power dissipation output current or safe operating area limits of the IC
regulator must never be exceeded.
3. Operation with a Load Common to a Voltage of Opposite Polarity

In many cases, a regulator powers a load which is not connected to ground but instead is connected
to a voltage source of opposite polarity (e.g. op amps, level shifting circuits, etc.). In these cases, a clamp
diode should be connected to the regulator output as shown in Figure 31F. This protects the regulator,
during startup and short circuit operation, from output polarity reversals.
Figure 31F. Output Polarity Reversal Protection
+ Vin
+ VO
Positive
Regulator
1N4001
or Equiv
Load
1N4001
or Equiv
Vin
Negative
Regulator
VO
3841
4. Reverse Bias Protection

Occasionally, there exists the possibility that the input voltage to the regulator can collapse faster than
the output voltage. This could occur, for example, if the input supply is crowbarred during an output
overvoltage condition. If the output voltage is greater 7.0 V, the emitterbase junction of the series pass
element (internal or external) could break down and be damaged. To prevent this, a diode shunt can be
employed, as shown in Figure 32F.
Figure 33F shows a threeterminal positiveadjustable regulator with the recommended protection
diodes for output voltages in excess of 25 V, or high output capacitance values (CO > 25 F, CAdj >10 F).
Diode D1 prevents CO from discharging through the regulator during an input short circuit. Diode D2
protects against capacitor CAdj from discharging through the regulator during an output short circuit. The
combination of diodes D1 and D2 prevents CAdj from discharging through the regulator during an input
short circuit.
Figure 32F. Reverse Bias Protection
Figure 33F. Reverse Bias Protection for

ThreeTerminal Adjustable Regulators
D1
Vin
Positive
Regulator
+ VO
1N4002
Vin
Positive
Adjustable
Regulator
Vout
R1
Cin
+ VO
D2
+
1N4002
CO
Adjust
R2
CAdj
+ VO
3842
SECTION 4
SERIES PASS ELEMENT CONSIDERATIONS
FOR LINEAR REGULATORS
Presently, most monolithic IC voltage regulators that are available have output current capabilities from
100 mA to 3.0 A. If greater current capability is required, or if the IC regulator does not possess sufficient
safeoperatingarea (SOA), the addition of an external series pass element is necessary.
In this section, configurations, specifications and current limit techniques for external series pass
elements will be considered. For illustrative purposes, pass elements for only positive regulator types will
be discussed. However, the same considerations apply for pass elements used with negative regulators.
A. Series Pass Element Configurations

Using an NPN Type Transistor
If the IC regulator has an external sense lead, an NPN type series pass element may be used, as shown
in Figure 41 A. This pass element could be a single transistor or multiple transistors arranged in
Darlington and/or paralleled configurations.
In this configuration, the IC regulator supplies the base current (IB) to the pass element (Q2) which
acts as a current amplifier and provides the increased output current (IO) capability.
Figure 41A. NPN Type Series Pass Element Configuration
External
Serial Pass Element
VCE(Q2)
IC(Q2)
C
Vin1*
IO
E
Q2
VO
IB(Q2)
IC Regulator (simplified)
Vin2
Q1
VO
IBias
VS
Sense Lead
*Vin1 may or may not equal Vin2, depending on the application.
3843
Using a PNP Type Transistor

If the IC regulator does not have an external sense lead, as in the case of the threeterminal fixed output
regulators, the configuration of Figure 41B can be used. (Regulators which possess an external sense
lead may also be used with this configuration.) As before, the PNP type pass element can be a single
transistor or multiple transistors.
Figure 41B. PNP Type Series Pass Element Configuration
External
Series Pass Element
VCE(Q2)
E
Vin1
Q2
IC(Q2)
B
IB(Q2)
IC Regulator (simplified)
IO
Q1
VO
Vin1
IBias
This configuration functions in a similar manner to that of Figure 41A, in that the regulator supplies
base current to pass element. The resistor (R) serves to route the IC regulator bias current (IBias) away
from the base of Q2. If not included, regulation would be lost at low output currents. The value of R is low
enough to prevent Q2 from turning on when IBias flows through this resistor, and is given by:
VBEon(Q2 )
(4.0)
0<R
IBias
B. Series Pass Element Specifications

Independent of which configuration is utilized, the transistor or transistors that compose the pass
element must have adequate ratings for IC(max), VCEO, hfe, power dissipation, and safe operating area.
1. IC(max) for the pass element of Figure 41A, IC(max) is given by:
IC(max)(Q2) IO(max) IB(max)(Q2) = IO(max)
IO(max)
IC(max)(Q2)
hfe(Q2)
(4.1)
(4.2)
For the configuration of Figure 41B:
3844
IC(max)(Q2) IO(max) + IB(max)(Q2)
(4.3)
IO(max)
(4.4)
2. VCEO since VCE(Q2) is equal to Vin1(max) when the output is shorted or during start up:
VCEO(Q2) Vin1(max)
(4.5)
3. hfe the minimum DC current gain for Q2 in Figures 41A and 41B is given by:
hfe(min)(Q2)
IC(max)(Q2)
IB(max)(Q2)
@ VCE = (Vin1(min) VO)
(4.6)
4. Maximum Power Dissipation PD(max), and Safe Operating Area (SOA)

For any transistor there are certain combinations of IC and VCE at which it may safely be operated.
When plotted on a graph, whose axes are VCE and IC, a safeoperating region is formed.
As an example, the safeoperatingarea (SOA) curve for the well known 2N3055 NPN silicon power
transistor is shown in Figure 42. The boundaries of the SOA curve are formed by IC(max), power
dissipation, second breakdown and VCEO ratings of the transistor. Notice that the power dissipation
and second breakdown ratings are given for a case temperature of +25C and must be derated at higher
case temperatures. (Derating factors may be found in the transistors data sheets.) These boundaries
must never be exceeded during operation, or destruction of the transistor(s) which constitute the pass
element may result. (In addition, the maximum operating junction temperature must not be exceeded, see
Section 15.)
C. Current Limiting Techniques

In order to select a transistor or transistors with adequate SOA, the locus of pass element IC and VCE
operating points must be known. This locus of points is determined by the input voltage (Vin1, output voltage
(VO), output current (IO) and the type of output current limiting technique employed.
In most cases, Vin1, VO, and the required output current are already known. All that is left to determine
is how the chosen current limit scheme affects required pass element SOA.
Note, since the external pass element is merely an extension of the IC regulator, the following
discussions apply equally well to IC regulators not using an external pass element.
1. Constant Current Limiting

This method is the simplest to implement and is extensively used, especially at the lower output current
levels. The basic circuit configuration is shown in Figure 43A, and operates in the following manner.
As the output current increases, the voltage drop across RSC increases, proportionately. When the
output current has increased to the point that the voltage drop across RSC is equal to the baseemitter ON
voltage of Q3 (VBEon(Q3)), Q3 conducts. This diverts base current (IDrive) away from Q1, the IC regulators
internal series pass element. Base drive (IB(Q2)) of Q2 is therefore reduced and its collectoremitter
voltage increases, thereby reducing the output voltage below its regulated value, Vout. The resulting output
voltagecurrent characteristic is shown in Figure 43B.
The value of ISC is given by:
ISC =
VBEon(Q3)
RSC
(4.7)
3845
Figure 42. 2N3055 Safe Operating Area (SOA)

20
IC(max)
10
PD(max) @ TC = 25C
7.0
5.0
2N3055
SafeOperatingArea
I C , COLLECTOR CURRENT, (A)
3.0
2.0
1.0
Second Breakdown @ TC = 25C
0.7
0.5
0.3
0.2
VCEO
0.1
3.0
4.0
5.0
7.0
10
20
40
60
VCE, COLLECTORTOEMITTER VOLTAGE, (V)
3846
Figure 43. Constant Current Limiting
(a)
(b)
External
Pass Element
VCE(Q2)
Vin1
Q2
Q1
Vout
IO
RSC
Ib(Q2)
VO, OUTPUT VOLTAGE
IC(Q2)
VO
VBE(Q3)
IDrive
Q3
IO, OUTPUT CURRENT
ISC
IC Regulator
By using the base of Q1 in the IC regulator as a control point, this configuration has the added benefit
of limiting the IC regulator output current (IB(Q2)) to Isc/hfe(Q2), as well as limiting the collector current of
Q2 to ISC. Of course, access to this point is necessary. Fortunately, it is usually available in the form of
a separate pin or as the regulators compensation terminal.(1)
The required safeoperatingarea for Q2 can be obtained by plotting the VCE and IC of Q2 given by:
VCE(Q2) = Vin1 VO IORSC
IC(Q2)
] IO
] Vin1 VO
(4.8)
(4.9)
where, VO = Vout for 0 IO ISC
(4.10)
and, IO = ISC for 0 VO Vout
(4.11)
The resulting plot is shown in Figure 44. The transistor chosen for Q2 must have an SOA which encloses
this plot, see Figure 44. Note that the greatest demand on the transistors SOA capability occurs when the
output of the regulator is short circuited and the pass element must support the full input voltage and short
circuit current simultaneously.
Figure 44. Constant Current Limit SOA Requirements
(See Section 3 for Circuit Techniques)
IC(max)
IC(Q2) , COLLECTOR CURRENT LOG
Pass Element SOA
ISC
Vin1 Vout
Vin1 VCEO
VCE(Q2), COLLECTOREMITTER VOLTAGE LOG
(1) The threeterminal regulators have internal current limiting and therefore do not provide
access to this point. If an external pass element is used with these regulators, constant
current limiting can still be accomplished by diverting pass element drive.
3847
2. Foldback Current Limiting

A disadvantage of the constant current limit technique is that in order to obtain sufficient SOA the pass
element must have a much greater collector current capability than is actually needed. If the short circuit
current could be reduced, while still allowing full output current to be obtained during normal regulator
operation, more efficient utilization of the pass elements SOA capability would result. This can be done
by using a foldback current limiting technique instead of constant current limiting.
The basic circuit configuration for this method is shown in Figure 45(A). The circuit operates in a
manner similar to that of the constant current limiting circuit, in that output current control is obtained by
diverting base drive away from Q1 with Q3.
At low output currents, VA approximately equals VO and VR2 is less than than VO. Q3 is therefore
nonconducting and the output voltage remains constant. As the output current increases, the voltage drop
across RSC increases until VA and VR2 are great enough to bias Q3 on. The output current at which this
occurs is IK, the knee current.
Figure 45. Foldback Current Limiting
(a)
(b)
External Pass Element

VCE(Q2)
VA
Q2
Vin1
IO
RSC
Ib(Q2)
Q1
VO, OUTPUT VOLTAGE
IC(Q2)
VO
R1
Vout
ISC
IDrive
IO, OUTPUT CURRENT
IK
Q3
IC Regulator
VBE(Q3)
R2
VR2
Figure 46. Foldback Current Limit SOA Requirements
I C(Q2), COLLECTOR CURRENT LOG
IC(max)
Pass Element
IK
Constant Current
Limiting
Foldback Current
Limiting
ISC
Vin1Vout
Vin1VCEO
VCE(Q2), COLLECTOREMITTER VOLTAGE LOG
3848
The output voltage will now decrease. Less output current is now required to keep VA and VR2 at a
level sufficient to bias Q3 on since the voltage at its emitter has the tendency to decrease faster than that
at its base. The output current will continue to foldback as the output voltage decreases, until an output
short circuit current level (ISC) is reached when the output voltage is zero. The resulting output
currentvoltage characteristic is shown in Figure 45B. The values for R1, R2, and RSC (neglecting base
current of Q3) are given by:
RSC =
)
1
Vout/ISC
I
Vout
K
ISC
VBEon(Q3)
(4.12)
R2
VBEon(Q3)
=
ISC RSC
R1 + R2
(4.13)
Vout
IDrive
(4.14)
and, R1 + R2
where: Vout = normal regulator output voltage

IK = knee current
ISC = short circuit current
IDrive = base drive to regulators internal pass element(s)
A plot of Q2 operating points, which result when using this technique, is shown in Figure 46. Note
that the pass element is required to operate with a collector current of only ISC during short circuit
conditions, not the full output current, IK. This results in a more efficient utilization of the SOA of Q2 allowing
the use of a smaller transistor than if constant current limiting were used. Although foldback current limiting
allows use of smaller pass element transistors for a given regulator output current than does constant
current limiting, it does have a few disadvantages.
Referring to Equation (4.12), as the foldback ratio (IK/ISC) is increased, the required value of RSC
increases. This results in a greater input voltage at higher foldback ratios. In addition, it can be seen for
Equation (4.12) that there exists an absolute limit to the foldback ratio equal to:
+
IK
ISC(max)
Vout
) VBEon(Q3)
for RSC
+R
(4.15)
For these reasons, foldback ratios greater than 2:1 or 3:1 are not usually practical for the lower output
voltage regulators.
3849
D. Paralleling Pass Element Transistors

Occasionally, it will not be possible to obtain a transistor with sufficient safeoperatingarea. In these
cases it is necessary to parallel two or more transistors. Even if a single transistor with sufficient capability
is available, it is possible that paralleling two smaller transistors is more economical.
In order to insure that the collector currents of the paralleled transistors are approximately equal, the
configuration of Figure 47 can be used. Emitterballasting resistors are used to force collectorcurrent
sharing between Q1 and Q2. The collectorcurrent mismatch can be determined by considering the
following, from Figure 47,
(4.16)
VBE1 + V1 = VBE2 + V2
and, VBE = V
(4.17)
where: VBE = VBE1 VBE2 and, V = V2 V1

Assuming IE1
] IC1 and IE2 ] OC2, the collectorcurrent mismatch is given by,

V1
V2
RE
RE
V2
RE
IC2 IC1
=
IC2
and, percent collectorcurrent mismatch =
V2 V1
VBE
V
=
=
V2
V2
V2
(4.18)
(4.19)
VBE
100%
V2
(4.20)
From Equation (4.20), the collectorcurrent mismatch is dependent on VBE and V2. Since VBE is
usually acceptable, V2 should be 1.0 V to 0.5 V, respectively. RE is therefore given by:
RE =
0.5 V to 1.0 V
0.5 V to 1.0 V
0.5 V to 1.0 V
=
=
IC1
IC2
IC/2
(4.21)
Figure 47. Paralleling Pass Element Transistors

IC
IC1
IC2
IB
Q1
Q2
VBEI
IE1
V1
3850
RE
QN
VBE2
V2
IE2
RE
SECTION 5
LINEAR REGULATOR CONSTRUCTION
AND LAYOUT
An important, and often neglected, aspect of the total regulator circuit design is the actual layout and
component placement of the circuit. In order to obtain excellent transient response performance, high
frequency transistors are used in modern integrated circuit voltage regulators. Proper attention to circuit
layout is therefore necessary to prevent regulator instability or oscillations, or degraded performance.
In this section, guidelines will be given on proper regulator layout and placement of circuit components.
In addition, topics such as remote voltage sensing, semiconductor mounting techniques, and thermal
system evaluations will also be discussed.
1. General Layout and Component Placement Considerations

As mentioned previously, modern integrated circuit regulators are necessarily high bandwidth devices
in order to obtain good transient response characteristics. To insure stable closedloop operation, all these
devices are frequency compensated, either internally or externally. This compensation can easily be upset
by unwanted stray circuit capacitances and lead inductances, resulting in spurious oscillations. Therefore,
it is important that the circuit lead lengths be short and the layout as tight as possible. Particular attention
should be paid to locating the compensation and bypass capacitors as close to the IC as possible. Lead
lengths associated with the external pass element(s), if used, should also be minimized.
Often overlooked is the stray inductance associated with the input leads to the regulator circuit. If the
lead length from the input supply filter capacitor to the regulator input is more than a couple of inches, a
0.01 F to 1.0 F high frequency type capacitor (tantalum, ceramic, etc.) should be used to bypass the
supply leads close to the regulator input pins.
2. Ground Loops and Remote Voltage Sensing

Ground Loops Regulator performance can also suffer if ground loops in the circuit wiring are not
avoided. The most common ground loop problem occurs when the return lead of the input supply filter
capacitor is improperly located, as shown in Figure 51. If this return lead is physically connected between
the load return and the regulator circuit ground point (B), a ripple voltage component (60 Hz or 120 Hz)
can be induced on the load voltage (VL). This is due to the high peaks of the filter capacitor ripple current
(Iripple) flowing through the lead resistance between the load and regulator. These peaks can be 5 to 15
times the value of load current. Since the regulator will only keep constant the voltage between its sense
lead and ground point, points A and B in Figure 51, this additional ripple voltage (Vlead), will appear at
the load.
This problem can be avoided by proper placement and connection of the filter capacitor return load as
shown in Figure 52.
Remote Voltage Sensing Closely related to the above ground loop problem is resistance in the current
carrying leads to the load. This can cause poorer than expected load regulation in cases where the load
currents are large or where the load is located some distance from the regulator. This is illustrated in Figure
53. As stated previously, the regulator circuit will keep the voltage present between its sense and ground
pins constant. From Figure 53 we can see that any lead resistance between these points and the load will
cause the load voltage (VL) to vary with varying load current, IL. This effectively lowers the load regulation of
the circuit.
3851
Figure 51. Filter Capacitor Ground Loop WRONG!

A
Regulator
Circuit
+
C
to
XFMR
VL
Vout
RL
RLead
Iripple
VLead
Figure 52. Filter Capacitor Ground Loop RIGHT!

A
Regulator
Circuit
+
C
Vout
VL
RL
to
XFMR
Iripple
This problem can be avoided by the use of remote Sense leads, as shown in Figure 54. The voltage
drops in the high current carrying leads now have no effect on the load voltage (VL). However, since the
Sense and Ground leads are usually rather long, care must be exercised that their associated lead
inductance is minimized, or loop instability may result. The Ground and Sense leads should be formed into
a twisted pair lead to minimize their lead inductance and noise pickup.
Figure 53. Effects of Resistance In Output Leads
Output
Vin
RLead
Regulator
Circuit
Sense
Gnd
Load
VL
IL
RLead
Figure 54. Remote Voltage Sensing

Output
Vin
RLead
Regulator
Circuit
Sense
+
Gnd
VL
RLead
3852
RL
IL
3. Mounting Considerations for Power Semiconductors

Current and power ratings of semiconductors are inseparably linked to their thermal environment.
Except for leadmounted parts used at low currents, a heat exchanger is required to prevent the junction
temperature from exceeding its rated limit, thereby running the risk of a high failure rate. Furthermore, the
semiconductor industrys field history indicated that the failure rate of most silicon semiconductors
decreases approximately by onehalf for a decrease in junction temperature from 160 to 135C.(1)
Guidelines for designers of military power supplies impose a 110C limit upon junction temperature.(2)
Proper mounting minimizes the temperature gradient between the semiconductor case and the
heat exchanger.
Most early life field failures of power semiconductors can be traced to faulty mounting procedures. With
metal packaged devices, faulty mounting generally causes unnecessarily high junction temperature,
resulting in reduced component lifetime, although mechanical damage has occurred on occasion from
improperly mounting to a warped surface. With the widespread use of various plastic packaged
semiconductors, the prospect of mechanical damage is very significant. Mechanical damage can impair
the case moisture resistance or crack the semiconductor die.
Figure 55 shows an example of doing nearly everything wrong. A tab mount TO220 package is
shown being used as a replacement for a TO213AA (TO66) part which was socket mounted. To use the
socket, the leads are bent an operation which, if not properly done, can crack the package, break the
internal bonding wires, or crack the die. The package is fastened with a sheet metal screw through a 1/4
hole containing a fiberinsulating sleeve. The force used to tighten the screw tends to pull the package into
the hole, possibly causing enough distortion to crack the die. In addition the contact area is small because
of the area consumed by the large hole and the bowing of the package, the result is a much higher junction
temperature than expected. If a rough heatsink surface and/or burrs around the hole were displayed in the
illustration, most but not all poor mounting practices would be covered.
Figure 55. Extreme Case of Improperly Mounting
a Semiconductor (Distortion Exaggerated)
Plastic Body
Leads
Package Heatsink
Mica Washer
Equipment
Heatsink
Socket for
TO213AA Package
Speed Nut
(Part of Socket)
Sheet Metal Screw
_________________________________
(1) MILHANDBOOK 2178, SECTION 2.2.
(2) Navy Power Supply Reliability Design and Manufacturing Guidelines NAVMAT P48551,
Dec. 1982 NAVPUBFORCEN,
5801 Tabor Ave., Philadelphia, PA 19120.
ChoTherm is a registered trademark of Chromerics, Inc.
Grafoil is a registered trademark of Union Carbide
Kapton is a registered trademark of E.I. Dupont
RubberDuc is a trademark of AAVID Engineering
Sil Pad is a trademark of Berquist
SyncNut is a trademark of ITW Shakeproof
Thermasil is a registered trademark and Thermafilm is a trademark of Thermalloy, Inc.
ICePAK, Full Pak, POWERTAP and Thermopad are trademarks of Motorola, Inc.
3853
In many situations the case of the semiconductor must be electrically isolated from its mounting
surface. The isolation material is, to some extent, a thermal isolator as well, which raises junction operating
temperatures. In addition, the possibility of arcover problems is introduced if high voltages are present.
Various regulating agencies also impose creepage distance specifications which further complicates
design. Electrical isolation thus places additional demands upon the mounting procedure.
Proper mounting procedures usually necessitate orderly attention to the following:
1. Preparing the mounting surface
2. Applying a thermal grease (if required)
3. Installing the insulator (if electrical isolation is desired)
4. Fastening the assembly
5. Connecting the terminals to the circuit
In this note, mounting procedures are discussed in general terms for several generic classes of
packages. As newer packages are developed, it is probable that they will fit into the generic classes
discussed in this note. Unique requirements are given on data sheets pertaining to the particular package.
The following classes are defined:
Flange Mount
Tab Mount
Plastic Body Mount
Surface Mount
Appendix A contains a brief review of thermal resistance concepts.
Appendix B discusses measurement difficulties with interface thermal resistance tests.
Mounting Surface Preparation
In general, the heatsink mounting surface should have a flatness and finish comparable to that of the
semiconductor package. In lower power applications, the heatsink surface is satisfactory if it appears flat
against a straight edge and is free from deep scratches. In high power applications, a more detailed
examination of the surface is required. Mounting holes and surface treatment must also be considered.
Surface Flatness
Surface flatness is determined by comparing the variance in height (h) of the test specimen to that
of a reference standard as indicated in Figure 56. Flatness is normally specified as a fraction of the Total
Indicator Reading (TIR). The mounting surface flatness (i.e, h/TIR) if less than 4 mils per inch, normal
for extruded aluminum, is satisfactory in most cases.
Figure 56. Surface Flatness Measurement

TIR = Total Indicator Reading
Sample
Piece
TIR
Reference
Piece
3854
Device Mounting Area
Surface Finish
Surface finish is the average of the deviations both above and below the mean value of surface height.
For minimum interface resistance, a finish in the range of 50 in. to 60 in. is satisfactory. A finer finish
is costly to achieve and does not significantly lower contact resistance. Tests conducted by Thermalloy
using a copper TO204 (TO3) package with a typical 32 in. finish, showed that heatsink finishes between
16 in. and 64 in. caused less than 2.5% difference in interface thermal resistance when the voids and
scratches were filled with a thermal joint compound.(3) Most commercially available cast or extruded
heatsinks will require spotfacing when used in high power applications. In general, milled or machined
surfaces are satisfactory if prepared with tools in good working condition.
Mounting Holes
Mounting holes generally should only be large enough to allow clearance of the fastener. The larger
thick flange type packages having mounting holes removed from the semiconductor die location, such as
the TO204AA, may successfully be used with larger holes to accommodate an insulating bushing, but
many plastic encapsulated packages are intolerant of this condition. For these packages, a smaller screw
size must be used such that the hole for the bushing does not exceed the hole in the package.
Punched mounting holes have been a source of trouble because if not properly done, the area around
a punched hole is depressed in the process. This crater in the heatsink around the mounting hole can
cause two problems. The device can be damaged by distortion of the package as the mounting pressure
attempts to conform it to the shape of the heatsink indentation, or the device may only bridge the crater
and leave a significant percentage of its heatdissipating surface out of contact with the heatsink. The first
effect may often be detected immediately by visual cracks in the package (if plastic), but usually an
unnatural stress is imposed, which results in an earlylife failure. The second effect results in hotter
operation and is not manifested until much later.
Although punched holes are seldom acceptable in the relatively thick material used for extruded
aluminum heatsinks, several manufacturers are capable of properly utilizing the capabilities inherent in
both fineedge blanking or shearedthrough holes when applied to sheet metal as commonly used for
stamped heatsinks. The holes are pierced using Class A progressive dies mounted on fourpost die sets
equipped with proper pressure pads and holding fixtures.
When mounting holes are drilled, a general practice with extruded aluminum, surface cleanup is
important. Chamfers must be avoided because they reduce heat transfer surface and increase mounting
stress. However, the edges must be broken to remove burrs which cause poor contact between device and
heatsink and may puncture isolation material.
Surface Treatment
Many aluminum heatsinks are blackanodized to improve radiation ability and prevent corrosion.
Anodizing results in significant electrical but negligible thermal insulation. It need only be removed from
the mounting area when electrical contact is required. Heatsinks are also available which have a nickel
plated copper insert under the semiconductor mounting area. No treatment of this surface is necessary.
Another treated aluminum finish is iridite, or chromateacid dip, which offers low resistance because
of its thin surface, yet has good electrical properties because it resists oxidation. It need only be cleaned
of the oils and films that collect in the manufacture and storage of the sinks, a practice which should be
applied to all heatsinks.
For economy, paint is sometimes used for sinks; removal of the paint where the semiconductor is
attached is usually required because of the paints high thermal resistance. However, when it is necessary
to insulate the semiconductor package from the heatsink, hard anodized or painted surfaces allow an easy
installation for low voltage applications. Some manufacturers will provide anodized or painted surfaces
meeting specific insulation voltage requirements, usually up to 400 V.
It is also necessary that the surface be free from all foreign material, film, and oxide (freshly bared
aluminum forms an oxide layer in a few seconds). Immediately prior to assembly, it is a good practice to
polish the mounting area with No. 000 steel wool, followed by an acetone or alcohol rinse.
________________________________
(3) Catalog #87HS9 (1987), page 8, Thermalloy, Inc., P.O. Box 810839, Dallas, Texas 753810839.
3855
Interface Decisions
When any significant amount of power is being dissipated, something must be done to fill the air voids
between mating surfaces in the thermal path. Otherwise, the interface thermal resistance will be
unnecessarily high and quite dependent upon the surface finishes.
For several years, thermal joint compounds, often called grease, have been used in the interface. They
have a resistivity of approximately 60C/W/in whereas air has 1200C/W/in. Since surfaces are highly
pockmarked with minute voids, use of a compound makes a significant reduction in the interface thermal
resistance of the joint. However, the grease causes a number of problems, as discussed in the following
section. To avoid using grease, manufacturers have developed dry conductive and insulating pads to
replace the more traditional materials. These pads are conformal and therefore partially fill voids when
under pressure.
Thermal Compounds (Grease)
Joint compounds are a formulation of fine zinc or other conductive particles in a silicone oil or other
synthetic base fluid which maintains a greaselike consistency with time and temperature. Since some of
these compounds do not spread well, they should be evenly applied in a very thin layer using a spatula
or lintless brush, and wiped lightly to remove excess material. Some cyclic rotation of the package will help
the compound spread evenly over the entire contact area. Some experimentation is necessary to
determine the correct quantity; too little will not fill all the voids, while too much may permit some compound
to remain between well mated metal surfaces where it will substantially increase the thermal resistance
of the joint.
To determine the correct amount, several semiconductor samples and heatsinks should be assembled
with different amounts of grease applied evenly to one side of each mating surface. When the amount is
correct, a very small amount of grease should appear around the perimeter of each mating surface as the
assembly is slowly torqued to the recommended value. Examination of a dismantled assembly should
reveal even wetting across each mating surface. In production, assemblers should be trained to slowly
apply the specified torque even though an excessive amount of grease appears at the edges of mating
surfaces. Insufficient torque causes a significant increase in the thermal resistance of the interface.
To prevent accumulation of airborne particulate matter, excess compound should be wiped away using
a cloth moistened with acetone or alcohol. These solvents should not contact plasticencapsulated
devices, as they may enter the package and cause a leakage path or carry in substances which might
attack the semiconductor chip.
Data showing the effect of compounds on several package types under different mounting conditions
is shown in Table 51. The rougher the surface, the more valuable the grease becomes in lowering contact
resistance; therefore, when mica insulating washers are used, use of grease is generally mandatory. The
joint compound also improves the breakdown rating of the insulator.
Table 51. Approximate Values for Interface Thermal Resistance Data
from Measurements Performed In Motorola Applications Engineering Laboratory
Dry interface values are subject to wide variation because of extreme dependence upon surface conditions. Unless otherwise
noted the case temperature is monitored by a thermocouple located directly under the die reached through a hole in the heatsink.
(See Appendix B for a discussion of Interface Thermal Resistance Measurements.)
Package Type and Data
JEDEC
Outlines
Description
Interface Thermal Resistance (C/W)

Test
Torque
Torq
e
InLb
Dry
Lubed
Dry
Lubed
Type
See
Note
MetaltoMetal
With Insulator
TO204AA (TO3)
Diamond Flange
0.5
0.1
1.3
0.36
3 mil Mica
TO220AB
Thermowatt
1.2
1.0
3.4
1.6
2 mil Mica
1, 2
NOTES: 1. See Figures 57 and 58 for additional data on TO204AA and TO220 packages.
2. Screw not insulated (see Figure 512).
3856
Conductive Pads
Because of the difficulty of assembly using grease and the evaporation problem, some equipment
manufacturers will not, or cannot, use grease. To minimize the need for grease, several vendors offer dry
conductive pads which approximate performance obtained with grease. Data for a greased bare joint and
a joint using Grafoil, a dry graphite compound, is shown in the data of Figure 57. Grafoil is claimed to be
a replacement for grease when no electrical isolation is required; the data indicates it does indeed perform
as well as grease. Another conductive pad available from AAVID is called KONDUX. It is made with a
unique, grain oriented, flakelike structure (patent pending). Highly compressible, it becomes formed to
the surface roughness of both the heatsink and semiconductor. Manufacturers data shows it to provide
an interface thermal resistance better than a metal interface with filled silicone grease. Similar dry
conductive pads are available from other manufacturers. They are a fairly recent development; long term
problems, if they exist, have not yet become evident.
Insulation Considerations
Since most power semiconductors use are vertical device construction it is common to manufacture
power semiconductors with the output electrode (anode, collector or drain) electrically common to the
case; the problem of isolating this terminal from ground is a common one. For lowest overall thermal
resistance, which is quite important when high power must be dissipated, it is best to isolate the entire
heatsink/semiconductor structure from ground, rather than to use an insulator between the semiconductor
and the heatsink. Heatsink isolation is not always possible, however, because of EMI requirements, safety
reasons, instances where a chassis serves as a heatsink or where a heatsink is common to several
nonisolated packages. In these situations insulators are used to isolate the individual components from
the heatsink. Newer packages, such as the Motorola Full Pak and EMS modules, contain the electrical
isolation material within, thereby saving the equipment manufacturer the burden of addressing the
isolation problem.
Insulator Thermal Resistance
When an insulator is used, thermal grease is of greater importance than with a metaltometal contact,
because two interfaces exist instead of one and some materials, such as mica, have a hard, markedly
uneven surface. With many isolation materials reduction of interface thermal resistance of between 2 to
1 and 3 to 1 are typical when grease is used.
Data obtained by Thermalloy, showing interface resistance for different insulators and torques applied
to TO204 (TO3) and TO220 packages, is shown in Figure 57, for bare and greased surfaces. Similar
materials to those shown are available from several manufacturers. It is obvious that with some
arrangements, the interface thermal resistance exceeds that of the semiconductor (junctiontocase).
Referring to Figure 57, one may conclude that when high power is handled, beryllium oxide is
unquestionably the best. However, it is an expensive choice. (It should not be cut or abraided, as the dust
is highly toxic.) Thermafilm is a filled polyimide material which is used for isolation (variation of Kapton).
It is a popular material for low power applications because of its low cost ability to withstand high
temperatures, and ease of handling in contrast to mica which chips and flakes easily.
A number of other insulating materials are also shown. They cover a wide range of insulation
resistance, thermal resistance and ease of handling. Mica has been widely used in the past because it
offers high break down voltage and fairly low thermal resistance at a low cost but it certainly should be used
with grease.
Silicone rubber insulators have gained favor because they are somewhat conformal under pressure.
Their ability to fill in most of the metal voids at the interface reduces the need for thermal grease. When
first introduced, they suffered from cutthrough after a few years in service. The ones presently available
have solved this problem by having imbedded pads of Kapton or fiberglass. By comparing Figures 57(c)
and 57(d), it can be noted that Thermasil, a filled silicone rubber without grease, has about the same
interface thermal resistance as greased mica for the TO220 package.
3857
Figure 57. Interface Thermal Resistance Using Different Insulating

Materials as a Function of Mounting Screw Torque
1.0
1.6
1.4
(1)
1.2
(2)
(3)
(4)
(5)
1.0
0.8
(6)
(7)
0.6
0.4
(1) Thermalfilm, .002 (.05) thick

(2) Mica, .003 (.08) thick
(3) Mica, .002 (.05) thick
(4) Hard anodized, .020 (.51) thick
(5) Aluminum oxide, .062 (1.57) thick
(6) Berylium oxide, .062 (1.57) thick
(7) Bare joint no finish
(8) Grafoil, .005 (.13) thick*
*Grafoil is not an insulating material
0.2
(8)
0.9
0.8
0.7
0.6
0.5
(1)
0.4
(2) (3)
(5)
(4)
0.3
0.2
0.1
0
72 145 217 290 362 435

INTERFACE PRESSURE (psi)
(a) TO204AA (TO3)

Without Thermal Grease
4
(2)
(3)
(4)
(5)
(6) (7)
(8)
0
1
2
4
5 6
3
MOUNTING SCREW TORQUE (INLBS)
(c) TO220
Without Thermal Grease
(1) Thermalfilm, .022 (.05) thick

(2) Mica, .003 (.08) thick
(3) Mica, .002 (.05) thick
(4) Hard anodized, .020 (.51) thick
(5) Thermalsil Il, .009 (.23) thick
(6) Thermalsil Il, .006 (.15) thick
(7) Bare joint no finish
(8) Grafoil, .005 (.13) thick*
*Grafoil is not an insulating material
R CS , THERMAL RESISTANCE ( C/W)
(1)
72 145 217 290 362 435

INTERFACE PRESSURE (psi)
(b) TO204AA (TO3)

With Thermal Grease
(6)
(7)
0
1
2
3 4
5
6
0
1
2
3
4
5
6
0
2.0
5
4
3
(1)
(2)
(3)
(4)
(7)
1
0
0
1
2
3
4
5
6
(d) TO220
With Thermal Grease
Data Courtesy of Thermalloy
3858
A number of manufacturers offer silicone rubber insulators. Table 52 shows measured performance
of a number of these insulators under carefully controlled, nearly identical conditions. The interface thermal
resistance extremes are over 2:1 for the various materials. It is also clear that some of the insulators are
much more tolerant than others of outofflat surfaces. Since the tests were performed, newer products
have been introduced. The Bergquist K10 pad, for example, is described as having about 2/3 the interface
resistance of the Sil Pad 1000 which would place its performance close to the Chomerics 1671 pad. AAVID
also offers an isolated pad called RubberDuc, however it is only available vulcanized to a heatsink and
therefore was not included in the comparison. Published data from AAVID shows RCS below 0.3C/W for
pressures above 500 psi. However, surface flatness and other details are not specified so a comparison
cannot be made with other data in this note.
Table 52. Thermal Resistance of Silicone Rubber Pads
RCS @ 3 Mils*
Manufacturer
Product
Wakefield
Bergquist
Stockwell Rubber
Bergquist
Thermalloy
ShinEtsu
Bergquist
Chomerics
Wakefield
Bergquist
Ablestik
Thermalloy
Chomerics
Delta Pad 1737

Sil Pad K4
1867
Sil Pad 4009
Thermalsil II
TC30AG
Sil Pad 4007
1674
Delta Pad 1749
Sil Pad 1000
Thermal Wafers
Thermalsil III
1671
0.790
0.752
0.742
0.735
0.680
0.664
0.633
0.592
0.574
0.529
0.500
0.440
0.367
RCS @ 7.5 Mils*

1.175
1.470
1.015
1.205
1.045
1.260
1.060
1.190
0.755
0.935
0.990
1.035
0.655
*Test Fixture Deviation from flat Thermalloy EIR861010.
The thermal resistance of some silicone rubber insulators is sensitive to surface flatness when used
under a fairly rigid base package. Data for a TO204AA (TO3) package insulated with Thermasil is shown
on Figure 58. Observe that the worst case encountered (7.5 mils) yields results having about twice the
thermal resistance of the typical case (3 mils), for the more conductive insulator. In order for Thermasil
III to exceed the performance of greased mica, total surface flatness must be under 2 mils, a situation that
requires spot finishing.
Figure 58. Effect of Total Surface Flatness on Interface
Resistance Using Silicon Rubber Insulators
INTERFACE THERMAL RESISTANCE ( C/W)
1.2
1.0
(1)
(2)
0.8
0.6
0.4
(1) Thermalsil Il, 0.009 inches (0.23 mm) thick.

(2) Thermalsil Il, 0.006 inches (0.15 mm) thick.
0.2
0
0
Data Courtesy of Thermalloy
0.002
0.004
0.006
0.008
0.01
TOTAL JOINT DEVIATION FROM FLAT OVER

TO3 HEADER SURFACE AREA (INCHES)
3859
Silicon rubber insulators have a number of unusual characteristics. Besides being affected by surface
flatness and initial contact pressure, time is a factor. For example, in a study of the ChoTherm 1688 pad
thermal interface impedance dropped from 0.90C/W to 0.70C/W at the end of 1000 hours. Most of the
change occurred during the first 200 hours where RCS measured 0.74C/W. The torque on the
conventional mounting hardware had decreased to 3 inlb from an initial 6 inlb. With nonconformal
materials, a reduction in torque would have increased the interface thermal resistance.
Because of the difficulties in controlling all variables affecting tests of interface thermal resistance, data
from different manufacturers is not in good agreement. Table 53 shows data obtained from two sources.
The relative performance is the same, except for mica which varies widely in thickness. Appendix B
discusses the variables which need to be controlled. At the time of this writing ASTM Committee D9 is
developing a standard for interface measurements.
The conclusions to be drawn from all this data is that some types of silicon rubber pads, mounted dry,
will out perform the commonly used mica with grease. Cost may be a determining factor in making
a selection.
Table 53. Performance of Silicon Rubber Insulators Tested per MILI49456
Measured Thermal Resistance (C/W)
Material
Thermalloy Data(1)
Bergquist Data(2)
Bare Joint, greased

BeO, greased
ChoTherm, 1617
Q Pad (noninsulated)
SilPad, K10
Thermasil III
0.033
0.082
0.233
0.263
0.267
0.008
0.009
0.200
Mica, greased
SilPad 1000
Chotherm 1674
Thermasil II
SilPad 400
SilPad K4
0.329
0.400
0.433
0.500
0.533
0.583
0.400
0.300
0.440
0.440
(1) From Thermalloy EIR 871030

(2) From Bergquist Data Sheet
Insulation Resistance
When using insulators, care must be taken to keep the mating surfaces clean. Small particles of foreign
matter can puncture the insulation, rendering it useless or seriously lowering its dielectric strength. In
addition, particularly when voltages higher than 300 V are encountered, problems with creepage may
occur. Dust and other foreign material can shorten creepage distances significantly, so having a clean
assembly area is important. Surface roughness and humidity also lower insulation resistance. Use of
thermal grease usually raises the withstand voltage of the insulation system but excess must be removed
to avoid collecting dust. Because of these factors, which are not amenable to analysis, hipot testing
should be done on prototypes and a large margin of safety employed.
Insulated Electrode Packages
Because of the nuisance of handling and installing the accessories needed for an insulated
semiconductor mounting, equipment manufacturers have longed for costeffective insulated packages
since the 1950s. The first to appear were stud mount types which usually have a layer of beryllium oxide
between the stud hex and the can. Although effective, the assembly is costly and requires manual
mounting and lead wire soldering to terminals on top of the case. In the late eighties, a number of electrically
isolated parts became available from various semiconductor manufacturers. These offerings presently
consist of multiple chips and integrated circuits as well as the more conventional single chip devices.
The newer insulated packages can be grouped into two categories. The first has insulation between
the semiconductor chips and the mounting base; an exposed area of the mounting base is used to secure
the part. The second category contains parts which have a plastic overmold covering the metal mounting
base. The Full Pak (Case 221C) illustrated in Figure 513, is an example of parts in the second category.
3860
Parts in the first category those with an exposed metal flange or tab are mounted the same as
their noninsulated counterparts. However, as with any mounting system where pressure is bearing on
plastic, the overmolded type should be used with a conical compression washer, described later in
this note.
Fastener and Hardware Characteristics

Characteristics of fasteners, associated hardware, and the tools to secure them determine their
suitability for use in mounting the various packages. Since many problems have arisen because of
improper choices, the basic characteristics of several types of hardware are discussed next.
Compression Hardware
Normal split ring lock washers are not the best choice for mounting power semiconductors. A typical
#6 washer flattens at about 50 pounds, whereas 150 to 300 pounds is needed for good heat transfer at
the interface. A very useful piece of hardware is the conical, sometimes called a Belleville washer,
compression washer. As shown in Figure 59, it has the ability to maintain a fairly constant pressure over
a wide range of its physical deflection generally 20% to 80%. When installing, the assembler applies
torque until the washer depresses to half its original height. (Tests should be run prior to setting up the
assembly line to determine the proper torque for the fastener used to achieve 50% deflection.) The washer
will absorb any cyclic expansion of the package, insulating washer or other materials caused by
temperature changes. Conical washers are the key to successful mounting of devices requiring strict
control of the mounting force or when plastic hardware is used in the mounting scheme. They are used
with the large face contacting the packages. A new variation of the conical washer includes it as part of
a nut assembly. Called a Sync Nut, the patented device can be soldered to a PC board and the
semiconductor mounted with a 632 machine screw.(4)
Figure 59. Characteristics of the Conical Compression Washers Designed
for Use with Plastic Body Mounted Semiconductors
PRESSURE ON PACKAGE (LB-F)
280
240
200
160
120
80
40
0
0
20
40
60
80
100
DEFLECTION OF WASHER DURING MOUNTING (%)
_________________________________
(4) ITW Shakeproof, St. Charles Road, Elgin, IL 60120.
3861
Clips
Fast assembly is accomplished with clips. When only a few watts are being dissipated, the small
boardmounted or freestanding heat dissipators with an integral clip, offered by several manufacturers,
result in a low cost assembly. When higher power is being handled, a separate clip may be used with larger
heatsinks. In order to provide proper pressure, the clip must be specially designed for a particular heatsink
thickness and semiconductor package.
Clips are especially popular with plastic packages such as the TO220 and TO126. In addition to fast
assembly, the clip provides lower interface thermal resistance than other assembly methods when it is
designed for proper pressure to bear on the top of the plastic over the die. The TO220 package usually
is lifted up under the die location when mounted with a single fastener through the hole in the tab because
of the high pressure at one end.
Machine Screws
Machine screws, conical washers, and nuts (or Sync Nut) can form a troublefree fastener system for
all types of packages which have mounting holes. However, proper torque is necessary. Torque ratings
apply when dry; therefore, care must be exercised when using thermal grease to prevent it from getting
on the threads as inconsistent torque readings result. Machine screw heads should not directly contact the
surface of plastic packages types as the screw heads are not sufficiently flat to provide properly distributed
force. Without a washer, cracking of the plastic case may occur.
SelfTapping Screws
Under carefully controlled conditions, sheet metal screws are acceptable. However, during the tapping
process with a standard screw, a volcanolike protrusion will develop in the metal being threaded; an
unacceptable surface that could increase the thermal resistance may result. When standard sheet metal
screws are used, they must be used in a clearance hole to engage a speed nut. If a selftapping process
is desired, the screw type must be used which rollforms machine screw threads.
Rivets
Rivets are not recommended fasteners for any of the plastic packages. When a rugged metal
flangemount package is being mounted directly to a heatsink, rivets can be used provided pressriveting
is used. Crimping force must be applied slowly and evenly. Popriveting should never be used because
the high crimping force could cause deformation of most semiconductor packages. Aluminum rivets are
much preferred over steel because less pressure is required to set the rivet and thermal conductivity
is improved.
The hollow rivet, or eyelet, is preferred over solid rivets. An adjustable, regulated pressure press is used
such that a gradually increasing pressure is used to pan the eyelet. Use of sharp blows could damage the
semiconductor die.
Solder
Until the advent of the surface mount assembly technique, solder was not considered a suitable
fastener for power semiconductors. However, user demand has led to the development of new packages
for this application. Acceptable soldering methods include conventional beltfurnace, irons, vaporphase
reflow, and infrared reflow. It is important that the semiconductor temperature not exceed the specified
maximum (usually 260C) or the die bond to the case could be damaged. A degraded die bond has
excessive thermal resistance which often leads to a failure under power cycling.
3862
Adhesives
Adhesives are available which have coefficients of expansion compatible with copper and aluminum.(5)
Highly conductive types are available; a 10 mil layer has approximately 0.3C/W interface thermal
resistance. Different types are offered: high strength types for nonfieldserviceable systems or low
strength types for fieldserviceable systems. Adhesive bonding is attractive when case mounted parts are
used in wave soldering assembly because thermal greases are not compatible with the conformal coatings
used and the greases foul the solder process.
Plastic Hardware
Most plastic materials will flow, but differ widely in this characteristic. When plastic materials form parts
of the fastening system, compression washers are highly valuable to assure that the assembly will not
loosen with time and temperature cycling. As previously discussed, loss of contact pressure will increase
interface thermal resistance.
Fastening Techniques
Each of the various classes of packages in use requires different fastening techniques. Details
pertaining to each type are discussed in following sections. Some general considerations follow.
To prevent galvanic action from occurring when devices are used on aluminum heatsinks in a corrosive
atmosphere, many devices are nickel or goldplated. Consequently, precautions must be taken not to mar
the finish.
Another factor to be considered is that when a copper based part is rigidly mounted to an aluminum
heatsink, a bimetallic system results which will bend with temperature changes. Not only is the thermal
coefficient of expansion different for copper and aluminum, but the temperature gradient through each
metal also causes each component to bend. If bending is excessive and the package is mounted by two
or more screws the semiconductor chip could be damaged. Bending can be minimized by:
1. Mounting the component parallel to the heatsink fins to provide increased stiffness.
2. Allowing the heatsink holes to be a bit oversized so that some slip between surfaces can
occur as temperature changes.
3. Using a highly conductive thermal grease or mounting pad between the
heatsink and semiconductor to minimize the temperature gradient and allow for movement.
Flange Mount
Few known mounting difficulties exist with the smaller flange mount packages, such as the TO204
(TO3). The rugged base and distance between die and mounting hose combine to make it extremely
difficult to cause any warpage unless mounted on a surface which is badly bowed or unless one side is
tightened excessively before the other screw is started. It is therefore good practice to alternate tightening
of the screws so that pressure is evenly applied. After the screws are fingertight the hardware should be
torqued to its final specification in at least two sequential steps. A typical mounting installation for a popular
flange type part is shown in Figure 510. Machine screws (preferred), selftapping screws, islets or rivets
may be used to secure the package using guidelines in the previous section, Fastener and Hardware
Characteristics.
___________________________________
(5) Robert Batson, Elliot Fraunglass and James P. Moran, Heat Dissipation Through Thermalloy Conductive Adhesives, EMTAS 83 Conference,
February 13, Phoenix, AZ; Society of Manufacturing Engineers, One SME Drive, P.O. Box 930, Dearborn, MI 48128.
3863
Figure 510. Hardware Used for a TO204AA (TO3) Flange Mount Part
No. 6 Sheet Metal Screw
Power
Transistor
Insulator
Insulating
Bushing
Heatsink
Socket
Tab Mount
The tab mount class is composed of a wide array of packages as illustrated in Figure 511. Mounting
considerations for all varieties are similar to that for the popular TO220 package, whose suggested
mounting arrangements and hardware are shown in Figure 512. The rectangular washer shown in Figure
512a is used to minimize distortion of the mounting flange; excessive distortion could cause damage to
the semiconductor chip. Use of the washer is only important when the size of the mounting hole exceeds
0.140 inch (632 clearance). Larger holes are needed to accommodate the lower insulating bushing when
the screw is electrically connected to the case; however, the holes should not be larger than necessary
to provide hardware clearance and should never exceed a diameter of 0.250 inch. Flange distortion is also
possible if excessive torque is used during mounting. A maximum torque of 8 inchpounds is suggested
when using a 632 screw.
Care should be exercised to assure that the tool used to drive the mounting screw never comes in
contact with the plastic body during the driving operation. Such contact can result in damage to the plastic
body and internal device connections. To minimize this problem, Motorola TO220 packages have a
chamfer on one end. TO220 packages of other manufacturers may need a spacer or combination spacer
and isolation bushing to raise the screw head above the top surface of the plastic.
3864
The popular TO220 package and others of similar construction lift off the mounting surface as
pressure is applied to one end. (See Appendix B, Figure B1.) To counter this tendency, at least one
hardware manufacturer offers a hard plastic cantilever beam which applies more even pressure on the
tab.(6) In addition, it separates the mounting screw from the metal tab. Tab mount parts may also be
effectively mounted with clips as shown in Figure 514(c). To obtain high pressure without cracking the
case, a pressure spreader bar should be used under the clip. Interface thermal resistance with the
cantilever beam or clips can be lower than with screw mounting.
Figure 511. Several Types of Tab Mounted Parts
CASE 221A
(TO220AB)
CASE 314D
CASE 340
(TO218)
Figure 512. Mounting Arrangements for Tab Mount TO220

a) Preferred Arrangement for Isolated or Nonisolated Mounting. Screw
a) is at Semiconductor Case Potential. 632 Hardware is Used.
b) Alternate Arrangement for Isolated Mounting when Screw

b) must be at Heatsink Potential. 440 Hardware is Used.
Use Parts Listed Below.
Choose from Parts Listed Below.
440 Pan or Hex Head Screw

632 Hex
Head Screw
Flat Washer
Insulating Bushing
(1) Rectangular Steel

Washer
Semiconductor
(Case 221, 221A)
Semiconductor
(Case 221,221A)
(2) Rectangular
Insulator
Heatsink
(2) Bushing
Rectangular
Insulator
Heatsink
(3) Flat Washer

Compression Washer
(4) Conical Washer
(1) Used with thin chassis and/or large hole.

(2) Used when isolation is required.
(3) Required when nylon bushing is used.
632 Hex Nut
440 Hex Nut
___________________________________
(6) Catalog, Edition 18, Richco Plastic Company, 5825 N. Tripp Ave., Chicago, IL 60546.
3865
Plastic Body Mount

The Full Pak plastic power packages shown in Figure 513 are typical of packages in this group. They
have been designed to feature minimum size with no compromise in thermal resistance.
The Full Pak (Case 221C) is similar to a TO220 except that the tab is encased in plastic. Because
the mounting force is applied to plastic, the mounting procedure differs from a standard TO220 and is
similar to that of the Thermopad.
Several types of fasteners may be used to secure these packages; machine screws, eyelets, or clips
are preferred. With screws or eyelets, a conical washer should be used which applies the proper force to
the package over a fairly wide range of deflection and distributes the force over a fairly large surface area.
Screws should not be tightened with any type of airdriven torque gun or equipment which may cause high
impact. Characteristics of a suitable conical washer is shown in Figure 59.
The Full Pak (Case 221C, 221D and 340B) permits the mounting procedure to be greatly simplified over
that of a standard TO220. As shown in Figure 514(c), one properly chosen clip, inserted into two slotted
holes in the heatsink, is all the hardware needed. Even though clip pressure is much lower than obtained
with a screw, the thermal resistance is about the same for either method. This occurs because the clip
bears directly on top of the die and holds the package flat while the screw causes the package to lift up
somewhat under the die. (See Figure B1 of Appendix B.) The interface should consist of a layer of thermal
grease or a highly conductive thermal pad. Of course, screw mounting shown in Figure 514(b) may also
be used but a conical compression washer should be included. Both methods afford a major reduction in
hardware as compared to the conventional mounting method with a TO220 package which is shown in
Figure 514(a).
Figure 513. Plastic Body Mounted Packages
CASE 221C
(Full Pak)
CASE 221D
(Full Pak)
CASE 340B
(Full Pak)
Figure 514. Mounting Arrangements for the Full Pak

as Compared to a Conventional TO220
440 Screw
Plain Washer
Insulating Bushing
Insulator
Heatsink
Threaded Side
632 Screw
Plain Washer
Clip
Heatsink
Compression Washer
Heatsink
Compression Washer
Nut
Nut
(a) Screw Mounted

TO220
3866
(b) Screw Mounted

Full Pak
(c) Clip Mounted

Full Pak
Surface Mount
Although many of the tab mount parts have been surface mounted, special small footprint packages
for mounting power semiconductors using surface mount assembly techniques have been developed. The
DPAK, shown in Figure 515, for example, will accommodate a die up to 112 mils 112 mils, and has a
typical thermal resistance around 2C/W junction to case. The thermal resistance values of the solder
interface is well under 1C/W. The printed circuit board also serves as the heatsink.
Standard glassepoxy 2 oz. boards do not make very good heatsinks because the thin foil has a high
thermal resistance. As Figure 516 shows, thermal resistance assymtotes to about 20C/W at 10 square
inches of board area, although a point of diminishing returns occurs at about 3 square inches.
Boards are offered that have thick aluminum or copper substrates. A dielectric coating designed for
low thermal resistance is overlayed with one or two ounce copper foil for the preparation of printed
conductor traces. Tests run on such a product indicate that case to substrate thermal resistance is in the
vicinity of 1C/W, exact values depending upon board type.(7) The substrate may be an effective heatsink
itself, or it can be attached to a conventional finned heatsink for improved performance.
Since DPAK and other surface mount packages are designed to be compatible with surface mount
assembly techniques, no special precautions are needed other than to insure that maximum
temperature/time profiles are not exceeded.
Figure 515. Surface Mounted DPAK Packages
CASE 369
CASE 369A
JUNCTION-TO-AIR (C/W)
R JA, THERMAL RESISTANCE
100
2.4
PD(max) for TA = 50C
Free Air
Mounted
Vertically
90
80
Minimum
Size Pad
70
60
2.0
2.0 oz. Copper

L
1.6
1.2
0.8
50
0.4
RJA
40
PD, MAXIMUM POWER DISSIPATION (W)
Figure 516. Effect of Footprint Area on Thermal Resistance

of DPAK Mounted on a GlassEpoxy Board
0
0
5.0
10
15
20
25
30
L, LENGTH OF COPPER (mm)
___________________________________
(7) Herb Fick, Thermal Management of Surface Mount Power Devices, Powerconversion and Intelligent Motion, August 1987.
3867
Free Air and Socket Mounting

In applications where average power dissipation is on the order of a watt or so, most power
semiconductors may be mounted with little or no heatsinking. The leads of the various metal power
packages are not designed to support the packages; their cases must be firmly supported to avoid the
possibility of cracked seals around the leads. Many plastic packages may be supported by their leads in
applications where high shock and vibration stresses are not encountered and where no heatsink is used.
The leads should be as short as possible to increase vibration resistance and reduce thermal resistance.
As a general practice however, it is better to support the package. A plastic support for the TO220
Package and other similar types is offered by heatsink accessory vendors.
In certain situations, in particular where semiconductor testing is required or prototypes are
being developed, sockets are desirable. Manufacturers have provided sockets for many of the
packages available from Motorola. The user is urged to consult manufacturers catalogs for
specific details. Sockets with Kelvin connections are necessary to obtain accurate voltage readings
across semiconductor terminals.
Connecting and Handling Terminals
Pins, leads, and tabs must be handled and connected properly to avoid undue mechanical stress which
could cause semiconductor failure. Change in mechanical dimensions as a result of thermal cycling over
operating temperature extremes must be considered. Standard metal, plastic, and RF stripline packages
each have some special considerations.
Metal Packages
The pins of metal packaged devices using glass to metal seals are not designed to handle any
significant bending or stress. If abused, the seals could crack. Wires may be attached using sockets, crimp
connectors or solder, provided the data sheet ratings are observed. When wires are attached directly to
the pins, flexible or braided leads are recommended in order to provide strain relief.
Plastic Packages
The leads of the plastic packages are somewhat flexible and can be reshaped although this is not a
recommended procedure. In many cases, a heatsink can be chosen which makes leadbending
unnecessary. Numerous lead and tabforming options are available from Motorola on large quantity
orders. Preformed leads remove the users risk of device damage caused by bending.
If, however, leadbending is done by the user, several basic considerations should be observed. When
bending the lead, support must be placed between the point of bending and the package. For forming small
quantities of units, a pair of pliers may be used to clamp the leads at the case, while bending with the fingers
or another pair of pliers. For production quantities, a suitable fixture should be made.
The following rules should be observed to avoid damage to the package.
1. A leadbend radius greater than 1/32 inch for TO220.
2. No twisting of leads should be done at the case.
3. No axial motion of the lead should be allowed with respect to the case.
The leads of plastic packages are not designed to withstand excessive axial pull. Force in this direction
greater than 4 pounds may result in permanent damage to the device. If the mounting arrangement
imposes axial stress on the leads, a condition which may be caused by thermal cycling, some method of
strain relief should be devised. When wires are used for connections, care should be exercised to assure
that movement of the wire does not cause movement of the lead at the leadtoplastic junctions. Highly
flexible or braided wires are good for providing strain relief.
Wire wrapping of the leads is permissible, provided that the lead is restrained between the plastic case
and the point of the wrapping. The leads may be soldered; the maximum soldering temperature, however,
must not exceed 260C and must be applied for not more than 5 seconds at a distance greater than 1/8
inch from the plastic case.
3868
Cleaning Circuit Boards

It is important that any solvents or cleaning chemicals used in the process of degreasing or flux removal
do not affect the reliability of the devices. Alcohol and unchlorinated freon solvents are generally
satisfactory for use with plastic devices, since they do not damage the package. Hydrocarbons such as
gasoline and chlorinated freon may cause the encapsulant to swell, possibly damaging the transistor die.
When using an ultrasonic cleaner for cleaning circuit boards, care should be taken with regard to
ultrasonic energy and time of application. This is particularly true if any packages are freestanding
without support.
Thermal System Evaluation

Assuming that a suitable method of mounting the semiconductor without incurring damage has been
achieved, it is important to ascertain whether the junction temperature is within bounds.
In applications where the power dissipated in the semiconductor consists of pulses at a low duty cycle,
the instantaneous or peak junction temperature, not average temperature, may be the limiting condition.
In this case, use must be made of transient thermal resistance data. For a full explanation of its use, see
Motorola Application Note, AN569.
Other applications, notably switches driving highly reactive loads, may create severe current crowding
conditions which render the traditional concepts of thermal resistance or transient thermal impedance
invalid. In this case, transistor safe operating area, thyristor di/dt limits, or equivalent ratings as applicable,
must be observed.
Fortunately, in many applications, a calculation of the average junction temperature is sufficient. It is
based on the concept of thermal resistance between the junction and a temperature reference point on
the case. (See Appendix A.) A fine wire thermocouple should be used, such as #36 AWG, to determine
case temperature. Average operating junction temperature can be computed from the following equation:
TJ = TC + RJC PD
where, TJ = junction temperature (C),
TC = case temperature (C),
RJC = thermal resistance junctiontocase as specified on the data sheet (C/W),
PD = power dissipated in the device (W).
The difficulty in applying the equation often lies in determining the power dissipation. Two commonly
used empirical methods are graphical integration and substitution.
Graphical Integration
Graphical integration may be performed by taking oscilloscope pictures of a complete cycle of the
voltage and current waveforms, using a limit device. The pictures should be taken with the temperature
stabilized. Corresponding points are then read from each photo at a suitable number of time increments.
Each pair of voltage and current values are multiplied together to give instantaneous values of power. The
results are plotted on linear graph paper, the number of squares within the curve counted, and the total
divided by the number of squares along the time axis. The quotient is the average power dissipation.
Oscilloscopes are available to perform these measurements and make the necessary calculations.
Substitution
This method is based upon substituting an easily measurable, smooth dc source for a complex
waveform. A switching arrangement is provided which allows operating the load with the device under test,
until it stabilizes in temperature. Case temperature is monitored. By throwing the switch to the test
position, the device under test is connected to a dc power supply, while another pole of the switch supplies
the normal power to the load to keep it operating at full power level. The dc supply is adjusted so that the
semiconductor case temperature remains approximately constant when the switch is thrown to each
position for about 10 seconds. The dc voltage and current values are multiplied together to obtain average
power. It is generally necessary that a Kelvin connection be used for the device voltage measurement.
3869
Appendix A
Thermal Resistance Concepts
The basic equation for heat transfer under steadystate conditions is generally written as:
q = hAT
(1)
where, q = rate of heat transfer or power dissipation (PD),
h = heat transfer coefficient,
A = area involved in heat transfer,
T = temperature difference between regions of heat transfer.
However, electrical engineers generally find it easier to work in terms of thermal resistance, defined
as the ratio of temperature to power. From Equation 1, thermal resistance (R) is
R = T/q = 1/hA
(2)
The coefficient (h) depends upon the heat transfer mechanism used and various factors involved in that
particular mechanism.
An analogy between Equation 2 and Ohms Law is often made to form models of heat flow. Note that
T could be thought of as a voltage thermal resistance corresponds to electrical resistance (R); and, power
(q) is analogous to current (I). This gives rise to a basic thermal resistance model for a semiconductor as
indicated by Figure A1.
Figure A1. Basic Thermal Resistance Model Showing Thermal
to Electrical Analogy for a Semiconductor
(TJ) Junction Temperature
Die
Insulators
Heatsink
Flat Washer
RJC
(TC) Case Temperature
PD
RCS
(TS) Heatsink
Temperature
RSA
(TA) Ambient
Temperature
Solder Terminal
Nut
Reference Temperature
The equivalent electrical circuit may be analyzed by using Kirchoffs Law and the following
equation results:
TJ = PD(RJC + RCS + RSA) + TA
(3)
where, TJ = junction temperature,
PD = power dissipation,
RJC = semiconductor thermal resistance (junctiontocase),
RCS = interface thermal resistance (casetoheatsink),
RSA = heatsink thermal resistance (heatsinktoambient),
TA = ambient temperature.
The thermal resistance junctiontoambient is the sum of the individual components. Each component
must be minimized if the lowest junction temperature is to result.
The value for the interface thermal resistance (RCS) may be significant compared to the other thermal
resistance terms. A proper mounting procedure can minimize RCS.
3870
The thermal resistance of the heatsink is not absolutely constant; its thermal efficiency increases as
ambient temperature increases and it is also affected by orientation of the sink. The thermal resistance of
the semiconductor is also variable; it is a function of biasing and temperature. Semiconductor thermal
resistance specifications are normally at conditions where current density is fairly uniform. In some
applications such as in RF power amplifiers and shortpulse applications, current density is not uniform
and localized heating in the semiconductor chip will be the controlling factor in determining power
handling ability.
Appendix B
Measurement of Interface Thermal Resistance
Measuring the interface thermal resistance RCS appears deceptively simple. All thats apparently
needed is a thermocouple on the semiconductor case, a thermocouple on the heatsink, and a means of
applying and measuring dc power. However, RCS is proportional to the amount of contact area between
the surfaces and consequently is affected by surface flatness and finish and the amount of pressure on
the surfaces. The fastening method may also be a factor. In addition, placement of the thermocouples can
have a significant influence upon the results. Consequently, values for interface thermal resistance
presented by different manufacturers are not in good agreement. Fastening methods and thermocouple
locations are considered in this Appendix.
When fastening the test package in place with screws, thermal conduction may take place through the
screws, for example, from the flange ear on a TO204AA package directly to the heatsink. This shunt path
yields values which are artificially low for the insulation material and dependent upon screw head contact
area and screw material. MILI49456 allows screws to be used in tests for interface thermal resistance
probably because it can be argued that this is application oriented.
Thermalloy takes pains to insulate all possible shunt conduction paths in order to more accurately
evaluate insulation materials. The Motorola fixture uses an insulated clamp arrangement to secure the
package which also does not provide a conduction path.
As described previously, some packages, such as a TO220, may be mounted with either a screw
through the tab or a clip bearing on the plastic body. These two methods often yield different values for
interface thermal resistance. Another discrepancy can occur if the top of the package is exposed to the
ambient air where radiation and convection can take place. To avoid this, the package should be covered
with insulating foam. It has been estimated that a 15% to 20% error in RCS can be incurred from
this source.
Another significant cause for measurement discrepancies is the placement of the thermocouple to
measure the semiconductor case temperature. Consider the TO220 package shown in Figure B1. The
mounting pressure at one end causes the other end where the die is located to lift off the mounting
surface slightly. To improve contact, Motorola TO220 Packages are slightly concave. Use of a spreader
bar under the screw lessens the lifting, but some is inevitable with a package of this structure.
B1. JEDEC TO220 Package Mounted to Heatsink Showing Various
Thermocouple Locations and Lifting Caused by Pressure at One End
Die
E.I.A.
Thermalloy

Motorola
3871
Three thermocouple locations are shown.

a) The Motorola location is directly under the die reached through a hole in the heatsink. The
thermocouple is held in place by a spring which forces the thermocouple into intimate contact with the
bottom of the semis case.
b) The JEDEC location is close to the die on the top surface of the package base reached through a
blind hole drilled through the molded body. The thermocouple is swaged in place.
c) The Thermalloy location is on the top portion of the tab between the molded body and the mounting
screw. The thermocouple is soldered into position.
Temperatures at the three locations are generally not the same. Consider the situation depicted in
Figure B1. Because the only area of direct contact is around the mounting screw, nearly all the heat travels
horizontally along the tab from the die to the contact area. Consequently, the temperature at the JEDEC
location is hotter than at the Thermalloy location and the Motorola location is even hotter. Since
junctiontosink thermal resistance must be constant for a given test setup, the calculated
junctiontocase thermal resistance values decrease and casetosink values increase as the case
temperature thermocouple readings become warmer. Thus the choice of reference point for the case
temperature is quite important.
There are examples where the relationship between the thermocouple temperatures are different from
the previous situation. If a mica washer with grease is installed between the semiconductor package and
the heatsink, tightening the screw will not bow the package; instead, the mica will be deformed. The primary
heat conduction path is from the die through the mica to the heatsink. In this case, a small temperature
drop will exist across the vertical dimension of the package mounting base so that the thermocouple at the
EIA location will be the hottest. The thermocouple temperature at the Thermalloy location will be lower but
close to the temperature at the EIA location as the lateral heat flow is generally small. The Motorola location
will be coolest.
The EIA location is chosen to obtain the highest temperature on the case. It is of significance because
power ratings are supposed to be based on this reference point. Unfortunately, the placement of the
thermocouple is tedious and leaves the semiconductor in a condition unfit for sale.
The Motorola location is chosen to obtain the highest temperature of the case at a point where,
hopefully, the case is making contact to the heatsink. Once the special heatsink to accommodate the
thermocouple has been fabricated, this method lends itself to production testing and does not mark the
device. However, this location is not easily accessible to the user.
The Thermalloy location is convenient and is often chosen by equipment manufacturers. However, it
also blemishes the case and may yield results differing up to 1C/W for a TO220 package mounted to
a heatsink without thermal grease and no insulator. This error is small when compared to the thermal
resistance of heat dissipaters often used with this package, since power dissipation is usually a few watts.
When compared to the specified junctiontocase values of some of the higher power semiconductors
becoming available, however, the difference becomes significant and it is important that the semiconductor
manufacturer and equipment manufacturer use the same reference point.
Another EIA method of establishing reference temperatures utilizes a soft copper washer (thermal
grease is used) between the semiconductor package and the heatsink. The washer is flat to within
1.0 mil/inch, has a finish better than 63 in., and has an imbedded thermocouple near its center. This
reference includes the interface resistance under nearly ideal conditions and is therefore
applicationoriented. It is also easy to use but has not become widely accepted.
A good way to improve confidence in the choice of case reference point is to also test for
junctiontocase thermal resistance while testing for interface thermal resistance. If the junctiontocase
values remain relatively constant as insulators are changed, torque varied, etc., then the case reference
point is satisfactory.
3872
SECTION 6
LINEAR REGULATOR DESIGN EXAMPLE
As an illustration of the use of the material contained in the preceding sections, the following regulator
design example is given.
Regulator Performance Requirements:
Output Voltage, VO = +10 V 0.1 V
Output Current, IO = 1.0 A, current limited
Load Regulation, 0.1% for IO = 10 mA to 750 mA
Line Regulation, 0.1%
Output ripple, 2.0 mVpp
Max Ambient Temperature, TA +70C
Supply will have common loads to a negative supply.
1. IC Regulator Selection
Study of the available regulators given in the selection guide reveals that the MC1723C would meet
the regulation performance requirements. This regulator must be current boosted to obtain the required
1.0 A output current. A rough cost estimate shows that an MC1723C series pass element combination is
the most economical approach.
2. Circuit Configuration
In Section 3, an appropriate circuit configuration is found. This is the MC1723C NPN boost
configuration of Figure 34A.
3. Determination of Component Values

Using the equations given in Figure 34A, the values of Cref, R1, R2, R3 and RSC are determined.
a) Cref is chosen to be 0.1 F for low noise operation.
b) R1 + R2 is chosen to be 10 k.
7.0 V
(R1 + R2) = 0.7 (10 k) = 7.0 k
c) R2 is then given by: R2
VO
d) Since Vref can vary by as much as 5% for the MC1723C, R2 should be made variable by at least
that much, so that VO can be set to the required value of +10 V 0.1 V. R2 is therefore chosen to
consist of a 62 k resistor and a 2.0 k trimpot.
e) R1 = 10 k R2 = 10 k 7.0 k = 3.0 k
f) RSC
0.6 V 0.6 V
=
= 0.6 ; 0.56 , 1.0 W chosen for RSC.
ISC 1.0 A
g) R3 = R1 R2 2.2 k
3873
4. Determination of Input Voltage (Vin)

There are two basic constraints on the input voltage: 1) the device limits for minimum and maximum
Vin and, 2) the minimum inputoutput voltage differential. These limits are found on the device data sheet
to be:
9.5 V Vin 40 V and (Vin VO) 3.0 V
For the configuration of Figure 35A, (Vin VO) is given by:
(Vin VO) = [Vin (VO + 2)] 3.0 V, where = VBEon 0.6 V
Note that (Vin VO) is defined on the device data sheet to be the differential between the input and output
pins. Since the baseemitter junction drops of Q1 and RSC have been added to the circuit, they must be
added to the minimum value of (Vin VO). Therefore,
Vin VO + 2 + 3.0 V = 10 + 1.2 + 3
Vin 14.2 V
This condition also satisfies the requirement for a minimum Vin of 9.5 V.
In order to simplify the design of the input supply (see Section 8), Vin is chosen to be 16 V average with
a 3.0 Vpp ripple at full load and up to 25 V at no load. This assures that the input voltage is always above
the required minimum value of 14.2 V. Now, the output ripple can be determined. The MC1723C has a
typical ripple rejection ratio of 74 db, as given on its data sheet. With an input ripple of 3.0 Vpp, the output
ripple would be less than 1.0 mVpp, which meets the regulator output ripple requirements.
5. Selection of the Series Pass Element (Q1)

The transistor type chosen for Q1 must have the following characteristics (see Section 4):
a) VCEO Vin(max)
b) IC(max) ISC
ISC
@ VCE = Vin VO , where = VBEon
c) hfe I
O
d) PD(max) Vin, ISC
[ 0.6 V
e) JC such to allow practical heatsinking

f) SOA such that it can withstand VCE = Vin @ IC = ISC
For this example: VCEO 25 V
IC(max) 1.0 A
hfe 25 @ VCE = 5.0 V @ IC = 1.0 A
PD(max) 16 W
JC = 1.52C/W
SOA = 1.0 A @ 16 V
A 2N3055 transistor is chosen as a suitable device for Q1 using the selection guide of Section 4 and the
transistor data sheets (available from the device manufacturer).
3874
6. Q1 Heatsink Calculation
TJ = TA + PD JA
where, PD = Vin ISC
JA = JC + CS + SA
Solving for SA:
(Equation 15.1 from Section 15)
(Equation 6.2)
SA =
TJ TA
(JC + CS)
PD
(6.2)
From the 2N3055 data sheet, TJ = 200C and JC = 1.52C/W. The transistor will be mounted with thermal
grease directly to the heatsink. Therefore, CS is found to be 0.1C/W from Table 151.
Solving for Equation 6.2:
200C 70C
(1.52 + 0.1) C/W
16 V 1.0 A
SA =
6.6C/W
A commercial heatsink is now chosen from Table 152 or one custom designed using the methods given
in Section 15. For this example, a Thermalloy #6003 heatsink, having a CS of 6.2C/W, was used.
7. Clamp Diode
Since the regulator can power a load which is also connected to a negative supply, a 1N4001 diode
is connected to the output for protection. The complete circuit schematic is shown in Figure 61.
Figure 61. 10 V, 1.0 A Design Example
2N3055 on
Thermalloy #6003
0.56, 1.0W
VO = +10 V, 1.0 A
RSC
Q1
Vin = +16 V
10
12
VBE
IO
11
R3
2.2k
VBE
MC1723CL
JA = 150C/W
3.0k
R1
5
13
0.1F
Cref
100pF
7
R2
2.0k
6.2k
8. Construction Input Supply Design

The input supply is now designed using the information contained in Section 8 and the regulator circuit
is constructed using the guidelines given in Section 5.
3875
SECTION 7
LINEAR REGULATOR CIRCUIT
TROUBLESHOOTING CHECKLIST
Occasionally, the designers prototype regulator circuit will not operate properly. If problems do occur,
the trouble can be traced to a design error in 99.9% of the cases. As a troubleshooting aid to the designer,
the following guide is presented.
Of course, it would be difficult, if not impossible, to devise a troubleshooting guide which would cover
all possible situations. However, the checklist provided will help the designer pinpoint the problem in the
majority of cases. To use the guide, first locate the problems symptom(s) and then carefully recheck the
regulator design in the area indicated using the information contained in the referenced handbook section.
If, after carefully rechecking the circuit, the designer is not successful in resolving the problem, seek
assistance from the factory by contacting the nearest Motorola Sales office.
Symptoms
Design Area to Check
Regulator oscillates
1.
2.
3.
4.
Layout
Compensation capacitor too small
Input leads not bypassed
External pass element parasitically oscillating
Loss of regulation at light loads
1. Emitterbase resistor in PNP type boost configuration too large

2. Absence of 1.0 mA minimum load.
(See load regulation test spec on device data sheet)
3. Improper circuit configuration
5
3
5
5
4
Loss of regulation at heavy loads
1.
2.
3.
4.
5.
IC regulator or pass element fails

after warmup or at high TA.
1. Inadequate heatsinking
2. Input Voltage Transient Vin(max), VCEO
Pass element fails during short

circuit.
1. Insufficient pass element ratings SOA, IC(max)

4
15
IC regulator fails during short

circuit.
1. IC current or SOA capability exceeded

IC regulator fails during powerup
1. Input voltage transient Vin(max)

2. IC current or SOA capability exceeded as load (capacitor)
is charged up.
2
2
IC regulator fails during

powerdown.
1. Regulator reverse biased
Output voltage does not come up

during powerup or after
short circuit
1. Out polarity reversal

2. Load has latchedup in some manner.
(Usually seen with op amps, current sources, etc.)
Excessive 60 Hz or 120 Hz
output ripple
1. Input supply filter capacitor ground loop
3876
Input voltage too low [Vin(min), |Vin VO|min]

External pass element gain too low
Current limit too low
Line resistance between sense points and load
Inadequate heatsinking
Section
2, 3
4
3
5
15
15
2, 4, 5
SECTION 8
DESIGNING THE INPUT SUPPLY
Most input supplies used to power series pass regulator circuits consist of a 60 Hz, single phase
stepdown transformer followed by a rectifier circuit whose output is smoothed by a choke or capacitor
input filter. The type of rectifier circuit used can be either a halfwave, fullwave, or fullwave bridge type,
as shown in Figure 81. The halfwave circuit is used in low current applications, while the fullwave is
preferable in highcurrent, low output voltage cases. The fullwave bridge is usually used in all other
highcurrent applications.
Figure 81. Rectification Schemes
(a) HalfWave
(b) FullWave or FullWave Center Tap
(c) FullWave Bridge
In this section, specification of the filter capacitor, rectifier and transformer ratings will be discussed.
The specifications for the choke input filter will not be considered since the simpler capacitor input type is
more commonly used in series regulated circuits. A detailed description of this type of filter can be found
in the reference listed at the end of this section.
3877
1. Design of CapacitorInput Filters

The best practical procedure for the design of capacitorinput filters still remains based on the
graphical data presented by Schade(1) in 1943. The curves shown in Figures 82 through 85 give all the
required design information for halfwave and fullwave rectifier circuits. Whereas Schade originally also
gave curves for the impedance of vacuumtube rectifiers, the equivalent values for semiconductor diodes
must be substituted. However, the rectifier forward drop often assumes more significance than the dynamic
resistance in lowvoltage supply applications, as the dynamic resistance can generally be neglected when
compared with the sum of the transformer secondarywinding resistance plus the reflected
primarywinding resistance. The forward drop may be of considerable importance, however, since it is
about 1.0 V, which clearly cannot be ignored in supplies of 12 V or less.
Figure 82. Relation of Applied Alternating Peak Voltage to Direct Output Voltage
in HalfWave CapacitorInput Circuits
100
0.05
0.5
1
2
RS
90
VM
VC
RL
80
% VC(DC) / VM
60
20
25
30
35
40
50
60
70
80
90
100
50
40
30
20
% RS /R L
6
8
10
12.5
15
70
10
0
0.1
1.0
= 2 f, f = Line Frequency
C in Farads
RL in Ohms
10
CRL
100
1000
________________________________
(1)From O. H. Schade, Proc. IRE, Vol. 31, p. 356, 1943.
3878
Figure 83. Relation of Applied Alternating Peak Voltage to

Direct Output Voltage in FullWave CapacitorInput Circuits
0.05
0.1
0.5
1
100
90
VM
RS
VM
RS
FullWave
C VC
RL
2
4
FullWave
Bridge
80
8
12.5
15
70
20
60
25
% RS /R L
% VC(DC) / VM
10
30
35
40
50
50
60
70
40
30
80
90
100
0.1
1.0
10
CRL (C IN FARADS, RL IN OHMS)
100
1000
Figure 84. Relation of RMS and PeaktoAverage Diode Current in CapacitorInput Circuits
0.02
0.05
0.1
0.2
0.5
1.0
2.0
5.0
10
30
100
5
3
2
1
1.0
2.0
3.0
5.0
7.0
10
20
30
nCRL
50
70
100
200
300
1000
40
I F(Peak) IF(AV) (PER DIODE)
% RS /nR L
0.02
30
0.05
0.1
20
0.2
0.5
10
1.0
2.0
5.0
10
% RS /nR L
F = I F(R ) I F(AV) (PER DIODE)

S
10
30
100
3
1.0
2.0
3.0
5.0
7.0
10
1 for HalfWave SinglePhase Rectifier Circuits

2 for FullWave SinglePhase Rectifier Circuits
= 2 f, where f = Line Frequency
n=
20
30
nCRL
50
70
100
200
300
500
700 1000
C in Farads
RL in Ohms
RS = RMS Equivalent Source Resistance
3879
Figure 85. RootMeanSquare Ripple Voltage for CapacitorInput Circuits

100
70
50
Circuit
30
20
r f , RIPPLE FACTOR (%)
HalfWave
Parameter
RS/RL (%)
A
0.1
1.0
10
30
0.1
1.0
10
30
FullWave
10
7.0
5.0
3.0
2.0
1.0
0.7
0.5
0.3
0.2
0.1
1.0
2.0
3.0
C in Farads
RL in Ohms
5.0
7.0
10
20
30
50
70
100
200
300
500
1000
CRL
Returning to the above curves, the fullwave circuit will be considered. Figure 83 shows that a circuit
must operate with CRL 10 in order to hold the voltage reduction to less than 10% and CRL 40 to obtain
less than 2.0% reduction. However, it will also be seen that these voltage reduction figures require RS/RL,
where RS is now the total series resistance, to be about 0.1% which, if attainable, causes repetitive
peaktoaverage current ratios from 10 to 17 respectively, as can be seen from Figure 84. These ratios
can be satisfied by many diodes; however, they may not be able to tolerate the turnon surge current
generated when the inputfilter capacitor is discharged and the transformer primary is energized at the
peak of the input waveform. The rectifier is then required to pass a surge current determined by the peak
secondary voltage less the rectifier forward drop and limited only by the series resistance RS. In order to
control this turnon surge, additional resistance must often be provided in series with each rectifier. It
becomes evident, then, that a compromise must be made between voltage reduction on the one hand and
diode surge rating and hence average currentcarrying capacity on the other hand. If small voltage
reduction, that is good voltage regulation, is required, a much larger diode is necessary than that
demanded by the average current rating.
Surge Current
The capacitorinput filter allows a large surge to develop, because the reactance of the transformer
leakage inductance is rather small. The maximum instantaneous surge current is approximately VM/RS
and the capacitor charges with a time constant RS C1. As a rough but conservative check, the
surge will not damage the diode if VM/RS is less than the diode IFSM rating and is less than 8.3 ms. It is
wise to make RS as large as possible and not pursue tight voltage regulation; therefore, not only will the
surge be reduced but rectifier and transformer ratings will more nearly approach the DC power
requirements of the supply.
3880
2. Design Procedure
A) From the regulator circuit design (see Section 6), we know:
VC(DC) = the required full load average dc output voltage of the capacitor input filter
VRipple(pp) = the maximum no load peaktopeak ripple voltage
Vm = the maximum no load output voltage
IO = the fullload filter output current
f = the input ac line frequency
B) From Figure 85, we can determine a range of minimum capacitor values to obtain sufficient ripple
attenuation. First determine rf:
VRipple(pp)
100%
rf =
(8.1)
2 2 VC(DC)
A range for CRL can now be found from Figure 85.
C) Next, determine the range of RS/RL from Figure 82 or 83 using VC(DC) and the values for CRL found
in part B. If the range of CRL values initially determined from Figure 85 is above 10, RS/RL can be
found from Figures 82 and 83 using the lowest CRL value. Otherwise, several iterations between
Figures 82 or 83 and 85 may be necessary before an exact solution for RS/RLand CRL for a given
rf and VC(DC)/Vm can be found.
D) Once CRL is found, the value of the filter capacitor (C) can be determined from:
CRL
C=
VC(DC)
2f
IO
(8.2)
E) The rectifier requirements may now be determined:

1. Average current per diode;
IF(avg) = IO for halfwave rectification
(8.3)
= IO/2 for fullwave rectification
2. RMS and Peak repetitive rectifier current ratings can be determined from Figure 84.
3. The rectifier PIV rating is 2 Vm for the halfwave and fullwave circuits, Vm for the full
wave bridge circuit. In addition, a minimum safety margin of 20% to 50% is advisable
due to the possibility of line transients.
4. Maximum surge current, Isurge = Vm/(RS + ESR)
(8.4)
where, ESR = minimum equivalent series resistance of filter capacitor from its data sheet.
F) Transformer Specification
1. Secondary leg RMS voltage, VS = {Vm + (n) 1.0}/ 2
where; n = 1 for halfwave and fullwave
n = 2 for fullwave bridge
2. Total resistance of secondary and any external resistors to be equal to RS found from
Figures 82, 83, and 84 (see Part C).
3. Secondary RMS current; halfwave = Irms
fullwave = Irms
fullwave bridge = 2 Irms
where, Irms = rms rectifier current (from part E.1 and E.2).
4. Transformer VA rating; halfwave = VS Irms
fullwave = 2 VS Irms
fullwave bridge = VS Irms ( 2 )
where, Irms = rms rectifier current (from part E.1 and E.2) and,
where, VS = secondary leg RMS voltage.
(8.5)
(8.6)
(8.7)
3881
3. Design Example
A) Find the values for the filter capacitor, transformer rectifier ratings, given
FullWave Bridge Rectification;
VC(DC) = 16 V
VRipple(pp) = 3.0 V
VM = 25 V
IO = 1.0 A
f = 60 Hz
B) Using Equation (8.1),
rf =
from Figure 8.5, CRL
] 7 to 15
3
100% = 6.6%
2 2 (16)
C) Using CRL = 10, RS/RL is found from Figure 83 using,

VC(DC) 16
= 0.64 = 64%
=
25
VM
RS/RL = 20% or RS = 0.2 RL = 0.2
VC(DC)
= 0.2 (16)
IO
RS = 3.2
D) From Equation (8.2), the filter capacitor size is found:

CRL
10
=
C=
= 1658 F
VC(DC)
2f(60)16
2f
IO
E) The rectifier ratings are now specified:
1. IF(avg) = IO/2 = 0.5 A from Equation (8.3)
2. IF(rms) = 2 IF(AVG) = 1.0 A from Figure 84
3. IF(Peak) = 5.2 IF(AVG) = 2.6 A from Figure 84
4. PIV = VM = 25 V (use 50 V for safety margin)
5. Isurge = VM/(RS + ESR)
25/3.2 = 7.8 A from Equation (8.4), neglecting capacitor ESR.
F) The transformer should have the following ratings:

1. VS = {VM + n(1.0)}/ 2 = (25 + 2)/ 2 = 19 VRMS {from Equation (8.5)}
2. Secondary Resistance should be 3.2
3. Secondary RMS current rating should be 1.4 A, (from Equation (8.6)).
4. From Equation (8.7), the transformer should have a 27 VA rating.
It should be noted that, in order to simplify the procedure, the above design does not allow for
line voltage variations or component tolerances. The designer should take these factors into account
when designing his input supply. Typical tolerances would be: line voltage = +10% to 15% and filter
capacitors = +75% to 10%.
________________________________
REFERENCES
1. O. H. Schade, Proc. IRE, Vol. 31, 1943.
2. Motorola Silicon Rectifier Manual, 1980.
3882
SECTION 9
AN INTRODUCTION TO SWITCHING
POWER SUPPLIES
The Switching Power Supply continues to increase in popularity and is one of the fastest growing
markets in the world of power conversion. Its performance and size advantages meet the needs of todays
modern and compact electronic equipment and the increasing variety of components directed at these
applications makes new designs even more practical.
This guide is intended to provide the designer with an overview of the more popular inverter circuits,
their basic theory of operation, and some of the subtle characteristics involved in selecting a circuit and
the appropriate components. Also included are valuable design tips on both the major passive and active
components needed for a successful design. Finally, a complete set of selector guides to Motorolas
Switchmode components is provided which gives a detailed listing of the industrys most comprehensive
line of semiconductor products for switching power supplies.
Comparison with Linear Regulators
The primary advantages of a switching power supply are efficiency, size,and weight. It is also a more
complex design, cannot meet some of the performance capabilities of linear supplies and generates a
considerable amount of electrical noise. However switchers are being accepted in the industry, particularly
where size and efficiency are of prime importance. Performance continues to improve and for most
applications they are usually cost competitive down to the 20 W power level.
In the past the switchers advantage versus the linear regulator was in the high power arena where
passive components such as transformers and filters were small compared to the linear regulator at the
same power level. However, active component count was high and tended to make the switcher less cost
effective at low power levels. In recent years, Switchers have been significantly cost reduced because
designers have been able to simplify the control circuits with new, cost effective integrated circuits and have
found even lower cost alternatives in the passive component area.
A performance comparison chart of switching versus linear supplies is shown in Table 91. Switcher
efficiencies run from 70% to 80% but occasionally fall to (60% to 65%) when linear post regulators are used
for the auxiliary outputs. Some linear power supplies on the other hand, are operated with up to 50%
efficiency but these are areas where line variations or holdup time problems are minimal. Most linears
operate with typical efficiencies of only 30%. The overall size reduction of a 20 kHz switcher is about 4:1
and newer designs in the 100 kHz to 200 kHz region end up at about 8:1 (versus a linear). Other
characteristics such as static regulation specs are comparable, while ripple and load transient response
are usually worse. Output noise specs can be somewhat misleading. Very often a 500 mV switching spike
at the output may be attenuated considerably at the load itself due to the series inductance of the
connecting cables and the additional filter capacitors found in many logic circuits. In the future, the noise
generated at higher switching frequencies (100 kHz to 500 kHz) will probably be easier to filter and the
transient response will be faster. Holdup time is greater for switchers because it is easier to store energy
in high voltage capacitors (200 V to 400 V) than in the lower voltage (20 V to 50 V) filter capacitors common
to linear power supplies. This is due to the fact that the physical size of a capacitor is dependent on its CV
product while energy storage is proportional to CV2.
3883
Table 91. 20 kHz Switcher versus Linear Performance

Parameter
Switcher
Linear
Efficiency
75%
30%
Size
2.0 W/in3
0.5 W/in3
Weight
40 W/lb
10 W/lb
Line and Load Regulation
0.1%
0.1%
Output Ripple Vpp
50 mV
5.0 mV
Noise Vpp
50 mV to 200 mV
Transient Response
1.0 ms
20 s
HoldUp Time
20 ms to 30 ms
1.0 ms to 2.0 ms
Basic Configurations
A switching power supply is a relatively complex circuit as is shown by the four basic building blocks
of Figure 91. It is apparent here that the heart of the supply is really the high frequency inverter. It is here
that the work of chopping the rectified line at a high frequency (20 kHz to 200 kHz) is done. It is here also
that the line voltage is transformed down to the correct output level for use by logic or other electronic
circuits. The remaining blocks support this basic function. The 60 Hz input line is rectified and filtered by
one block and after the inverter steps this voltage down, the output is again rectified and filtered by another.
The task of regulating the output voltage is left to the control circuit which closes the loop from the output
to the inverter. Most control circuits generate a fixed frequency internally and utilize pulse width modulation
techniques to implement the desired regulation. Basically, the ontime of the square wave drive to the
inverter is controlled by the output voltage. As load is removed or input voltage increases,the slight rise
in output voltage will signal the control circuit to deliver shorter pulses to the inverter and conversely as
the load is increased or input voltage decreases, wider pulses will be fed to the inverter.
The inverter configurations used in todays switchers actually evolved from the buck and boost circuits
shown in Figures 92a and 92b. In each case the regulating means and loop analysis will remain the same
but a transformer is added in order to provide electrical isolation between the line and load. The forward
converter family which includes the pushpull and half bridge circuits evolved from the buck regulator
(Figure 92a). And the newest switcher, the flyback converter, actually evolved from the boost regulator.
The buck circuit interrupts the line and provides a variable pulse width square wave to a simple averaging
LC filter. In this case, the first order approximation of the output voltage is Vout = Vin duty cycle and
regulation is accomplished by simply varying the duty cycle. This is satisfactory for most analysis work and
only the transformer turns ratio will have to be adjusted slightly to compensate for IR drops, diode drops,
and transistor saturation voltages.
Operation of the boost circuit is more subtle in that it first stores energy in a choke and then delivers
this energy plus the input line to the load. However, the flyback regulators which evolved from this
configuration delivers only the energy stored in the choke to the load. This method of operation is actually
based on the buck boost model shown in Figure 92c. Here, when the switch is opened, only the stored
inductive energy is delivered to the load. The true boost circuit can also regulate by stepping up (or
boosting) the input voltage whereas the buckboost or flyback regulator can step the input voltage up or
down. Analysis of the boost regulator begins by dealing with the choke as an energy storage element which
delivers a fixed amount of power to the load: PO = 1/2 L IfO where, I = the peak choke current; fO = the
operating frequency; and, L = the inductance.
Because it delivers a fixed amount of power to the load regardless of load impedance (except for short
circuits), the boost regulator is the designers first choice in photoflash and capacitivedischarge (CD)
automotive ignition circuits to recharge the capacitive load. It also makes a good battery charger. For an
electronic circuit load, however, the load resistance must be known in order to determine the
output voltage:
LfORL
where, RL = the load resistance.
VO = PORL = I
2
In this case, the choke current is proportional to the ontime or duty cycle of the switch and regulation for
fixed loads simply involves varying the duty cycle as before. However, the output also depends on the load
which was not the case with buck regulators and results in a variation of loop gain with load.
3884
Figure 91. Functional Block Diagram Switching Power Supply

5060 Hz
20 to 25 kHz
DC
DC
High Frequency
Inverter
Output
Line
Input Rectifier
and Filter
Output Rectifier
and Filter
Control Circuit
PWM
Note: Input to output isolation is not shown.
OSC
Comp
Ref
Figure 92. Nonisolated DCDC Converters
+ Vin
+ Vout
Vout Vin
+ Vin
+ Vout
Vout > Vin
(a) Buck (StepDown)
+ Vin
(b) Boost (StepUp)
Vout
(c) BuckBoost Regulator

which Resembles the Flyback Regulator
(StepUp or Down)
3885
For both regulators, transient response or responses to step changes in load are very difficult to
analyze. They lead to what is termed a load dump problem. This requires that energy already stored in
the choke or filter be provided with a place to go when load is abruptly removed. Practical solutions to this
problem include limiting the minimum load and using the right amount of filter capacitance to give the
regulator time to respond to this change.
The Future
The future offers a lot of growth potential for switchers in general and low power switchers
(20 W to 100 W) in particular. The latter are responding to the growth in microprocessor based equipment
as well as computer peripherals. Todays configurations have already been challenged by the sine wave
inverter which reduces noise and improves transistor reliability but does effect a cost penalty. Also, a trend
to higher switching frequencies to reduce size and cost even further has begun. The latest bipolar designs
operate efficiently up to 100 kHz and the FET seems destined to own the 200 kHz to 500 kHz range.
At this time there are a lot of safety and noise specifications. Originally governed only by MIL specs
and the VDE in Europe, now both UL and the FCC have released a set of specifications that apply to
electronic systems which often include switchers (see Table 92). It seems probable, however, that system
engineers or power supply designers will be able to add the necessary line filters and EMI shields without
evoking a significant cost penalty in the design.
The most optimistic note concerning switchers is in the component area. Switching power supply
components have actually evolved from components used in similar applications. And it is very likely that
newer and more mature products specifically for switchers will continue to appear over the next several
years. The ultimate effect of this evolution will be to further simplify, cost reduce and increase the reliability
of these designs.
Table 92. SMPS Specifications
Specification
Area
UL 478, VDE 0730, VDE 0806
Safety
VDE 0871, VDE 0875

MILSTD217D
MILSTD461A
DODSTD1399
FCC Class A & B
CSA C22.2, IEC 380
EMI
Reliability
EMI
Harmonic Content
EMI
Safety
The synchronous rectifier is one example of a new component developed specifically for low voltage
switchers. As requirements for 2.0 V and 3.0 V supplies emerge for use by fine geometry VLSI chips, the
only way to maintain decent conversion efficiency is to develop lower forward drop rectifiers. The
differences in 3.0 V and 5.0 V rectifier requirements are shown in Table 93. At this time, Motorola offers
low VF Schottky and area efficient TMOS III FETs for this task and is considering a variety of additional
technology options. The direct approach involves using low VF Schottkys or pinch rectifiers which will
feature VFs of 0.3 V to 0.4 V. The indirect approach involves using FETs or bipolar transistors and slightly
more complex circuitry like that shown in Figure 93. Both transistors will feature VFs of 0.2 V and, in
addition, the bipolar will have high EBOs (30 V) and high gain (100) with a recovery time of 100 ns.
And for designers who are not satisfied with the relatively low frequency limitations of square wave
switchers, there is the SRPS. The series resonant power supply topology seems to offer the possibility of
working in the 1.0 MHz region. If components like the relatively exotic power transformer can be cost
reduced, then it will be possible for this topology to become dominant in the market. The features generally
associated with this type of power supply are listed in Table 94 and a typical half bridge circuit is shown
in Figure 94. In a design now being studied in Motorolas advanced products laboratory, standard FETs,
Schottkys and ultrafast rectifiers all appear to work very well at 1.0 MHz.
3886
Figure 93. Synchronous Rectifiers

for 3.0 V Power Supplies
Table 93. Synchronous Rectifier

Requirements
G
Output
Voltage
Rectifier Characteristics
Primarily to reduce VF
also to reduce trr
VF
VR
5.0 V
0.5 V1.0 V
30 V60 V
3.0 V
0.3 V0.6 V
20 V40 V
VO
G
Note: The FET must be operated below VF of the
diode in order to gain the trr advantage.
Table 94. SRPS Features

Feature
Description
High Frequency
Todays line operated designs use sine waves in the 500 kHz to 1.0 MHz range.
Small Size
The ferrite transformer and polypropylene coupling capacitor are smaller than those
found in lower frequency square wave designs.
Low Noise
Switching occurs at zero crossings which reduces component stress and lowers EMI.
Efficient
Because switching losses are reduced, efficiency is high (typically 80%).
High Peak to Average

Current Ratios
Current ratings of the transistors and rectifiers are twice as high as similar flyback
designs.
Special Control Circuit
PDM (density) rather than PWM (width) control is used and requires a control IC
with a programmable VCO.
Market
The SRPS is expected to own 15% of the power supply market by 1990.
Figure 94. SRPS Block Diagram

AC
Line
Input
Rectifier
and Filter
1.0MHz
FET
Inverter
Series
Resonant
Tank and
Transformer
Schottky
Rectifiers
Output
Filter
Output
PDM
Control Circuit
60Hz
1.0 MHz Components
20kHz
PDM
Controller
3887
SECTION 10
SWITCHING REGULATOR TOPOLOGIES
FET and Bipolar Drive Considerations
There are probably as many base drive circuits for bipolars as there are designers. Ideally, the
transistor would like just enough forward drive (current) to stay in or near saturation and reverse drive that
varies with the amount of stored base charge such as a low impedance reverse voltage. Many of todays
common drive circuits are shown in Figure 101. The fixed drive circuits of Figure 10(a), (b) and (c) tend
to emphasize economy, while the Baker clamp and proportional drive circuits of Figure 10(d) and (e)
emphasize performance over cost.
FET drive circuits are another alternative. The standard that has evolved at this time is shown in Figure
102A. This transformer coupled circuit will produce forward and reverse voltages applied to the FET gate
which vary with the duty cycle as shown. For this example, a VGS rating of 20 V would be adequate for the
worst case condition of high logic supply (12 V) and minimum duty cycle. And yet, minimum gate drive
levels of 10 V are still available with duty cycles up to 50%. If wide variations in duty cycle are anticipated,
it might be wise to consider using a semiregulated logic supply for these situations. Finally, one point that
is not obvious when looking at the circuit is that FETs can be directly coupled to many ICs with only
100 mA of sink and source capability and still switch efficiently at 20 kHz. However, to achieve switching
efficiently at higher frequencies, 1.0 A to 2.0 A of drive may be required on a pulsed basis in order to quickly
charge and discharge the gate capacitances. A simple example will serve to illustrate this point and also
show that the Miller effect, produced by CDG, is the predominant speed limitation when switching high
voltages (see Figure 102B). A FET responds instantaneously to changes in gate voltage and will begin
to conduct when the threshold is reached (VGS = 2.0 V to 3.0 V) and be fully on with VGS = 7.0 V to 8.0 V.
Gate waveforms will show a porch at a point just above the threshold voltage which varies in duration
depending on the amount of drive current available and this determines both the rise and fall times for the
drain current.
Figure 101. Typical Bipolar Base Drive Circuits
12V
15
MC34060
(a) Fixed Drive, TurnOff

Energy Stored in Transformer
1.0k
MPS
U01
MPS
U95
(d) Standard
Baker Clamp
50F
+
105C
Low ESR
MJE13005
22
(c) Direct Drive

(b) Fixed Drive, TurnOff
Energy Stored in Capacitor
3888
(e) Proportional
Base Drive
Figure 102A. Typical Transformer Coupled FET Drive

12V
CDG
1:2
CGS
Wave Forms
VGS
50% Duty Cycle
10 V
0V
10 V
16 V
0V
4V
20% Duty Cycle
VGS Wave Forms
Figure 102B. FET Drive Current Requirements

VGS
100pF
CDG
500pF
CGS
Drive
Circuit
10 V
8.0 V
2.0 V
0V
1.0 A
IG + IM
0A
1.0 A
1. Miller Current for 30 ns:

IM = CDG dv/dt
300 V
= 1.0 A
= 100 pF
30 ns
2. Gate Cap Current for 30 ns:

IG = CGS dv/dt
6.0 V
= 0.1 A
= 500 pF
30 ns
To estimate drive current requirements, two simple calculations with gate capacitances can be made:
1. IM = CDGdv/dt and,
2. IG = CGSdv/dt
IM is the current required by the Miller Effect to charge the draintogate capacitance at the rate it is desired
to move the drain voltage (and current). And IG is usually the lesser amount of current required to charge
the gatetosource capacitance through the linear region (2.0 V to 8.0 V). As an example, if 30 ns
switching times are desired at 300 V, where CDG = 100 pF and CGS = 500 pF, then:
1. IM = 100 pF 300 V/30 ns = 1.0 A and,
2. IG = 500 pF 6.0 V/30 ns = 0.1 A
This example shows the direct proportion of drive current capability to speed and also illustrates that for
most devices, CDG will have the greatest effect on switching speed and that CGS is important only in
estimating turnon and turnoff delays.
Aside from its unique drive requirements, a FET is very similar to a bipolar transistor. Todays 400 V
FETs compete with bipolar transistors in many switching applications. They are faster and easier to drive,
but do cost more and have higher saturation, or more accurately, on voltages. The performance or
efficiency tradeoffs are analyzed using Figure 103, where typical power losses for switching transistors
versus frequency are shown. The FET (and bipolar) losses were calculated at 100C rather than 25C
because on resistance and switching times are highest here and 100C is typical of many applications.
These curves are asymptotes of the actual device performance, but are useful in establishing the
breakpoint of various devices, which is the point where saturation and switching losses are equal.
3889
TOTAL TRANSISTOR POWER LOSS (W)

PT = Pon + P swt
Figure 103. Typical Switching Losses at 300 V and 5.0 A (TJ = 100C)
100
30
Bipolar
tf = 100 ns
FET
tf = 20 ns
10
3.0
1.0
1.0
10
100
f, OPERATING FREQUENCY (Hz)
1.0
10
Control Circuits
Over the years, a variety of control ICs for SMPS have been introduced. The voltage mode controllers
diagramed in Table 101 still dominate this market. The basic regulating function is performed in the pulse
width modulator (PWM) section. Here, the dc feedback signal is compared to a fixed frequency sawtooth
waveform. The result is a variable duty cycle pulse train which, with suitable buffer or interface circuits, can
be used to drive the power switching transistor. Some ICs provide only a single output while others provide
a phase splitter or flipflop to alternately pulse two output channels. Additionally, most ICs provide an error
amplifier and reference section shown as a means to process, compare and amplify the feedback signal.
Features required by a control IC vary to some extent because of the particular needs of a designer
and on the circuit configuration chosen. However, most of todays current generation ICs have evolved with
the following capabilities or features:
Programmable (to 500 kHz) Fixed Frequency Oscillator
Linear PWM Section with Duty Cycle from 0% to 100%
On Board Error Amplifiers
On Board Reference Regulator
Adjustable Deadtime
Under Voltage (low VCC) Inhibit
Good Output Drive (100 mA to 200 mA)
Option of Single or Dual Channel Output
Uncommitted Output Collector and Emitter or Totem Pole Drive Configuration
SoftStart
Digital Current Limiting
Oscillator Sync Capability
It is primarily the cost differences in these parts that determine whether all or only part of these features
will be incorporated. Most of these are evident to the designer who has already started comparing
competitive device data sheets.
In addition to the control circuits listed in Table 102, Motorola also has two dc converter control chips,
the A78S40 and the MC34063A. These chips feature an onboard 40 V, 2.0 A switching transistor and
operate by dropping pulses from a fixed frequency, fixed duty cycle oscillator depending on load demand.
Today there is a demand for simple, low cost, single control ICs. These ICs, like Motorolas MC34060A
and MC34063A components, are used to run the lowpower flyback type configurations and are usually
part of a three chip rather than a single chip system. The differences in these two approaches are illustrated
in Figure 106.
When it is necessary to drive two or more power transistors, drive transformers are a practical interface
element and are driven by the conventional dual channel ICs. In the case of a single transistor converter,
however, it is usually more cost effective to directly drive the transistor from the IC. In this situation, an
optocoupler is commonly used to couple the feedback signal from the output back to this control IC. And
the error amplifier in this case is nothing more than a programmable zener like Motorolas TL431.
3890
Overvoltage Protection
Linear and switching power supplies can be protected from overvoltage with a crowbar circuit. For
linear supplies, the pass transistor can fail shorted, allowing high line transformer voltage to the load. For
switching power supplies, a loose or disconnected remote sense lead can allow high voltage to the load.
Table 101. Basic SM Control ICs
Control
Technique
Type A
Voltage Mode
Type B
Voltage Mode w/Latch
Osc
Schematic
Osc
Osc
+
FB
Latch
S
FB
R
Latch
+
PWM
Type C
Current Mode
+
PWM
PWM
FB
Single Channel
Parts
MC34060A
UC3842
MC34129
Dual Channel
Parts
TL494/594
SG3525A/27A
SG3526
Features
Low Cost
Digital Current Limiting,

Good Noise Immunity
Designed for Flyback,

Inherent Feed Forward
PWM
Waveforms
Output
Table 102. Control Circuits

Overvoltage
Protection
(OVP)
Standard
TL431
High
Performance
MC3423
TL431A
Over/Undervoltage
Protection
(O/UVP)
Undervoltage
Sense MPU/MCU
Reset
MC3425
MC34161
MC340645
MC341643
MC341645
The list of available circuits is shown in Table 102 and a typical 0 V application is shown in Figure 104.
This crowbar circuit ignores noise spikes but will fire the SCR when a valid overvoltage condition is
detected. The SCR will discharge C2 and either blow the fuse or cause the power supply to shut down.
Figure 104. Crowbar Circuit
Power
Supply
C2
MC3423
VO
For further information, see the MC3423 data sheet.
3891
Surge Current Protection

Many high current PWM switching supplies operate directly off the ac line. They have very large
capacitive input filters with high inrush surge currents. The line circuit breaker and the rectifier bridge must
be protected during turnon.
Surge current limiting can be accomplished by adding RS and an SCR short after charging C1, as
shown in Figure 105, or by phase controlling the line voltage with a Triac.
Figure 105. Surge Current Limiting for a Switching Power Supply
RS
AC
Line
Rectifier
Bridge
C1
RS
AC
Line
Rectifier
Bridge
C1
Transformer Design
With respect to transformer design, many of todays designers would say dont try it. Theyd advise
using a consultant or winding house to perform this task and with good reason. It takes quite a bit of time
to develop a feel for this craft and be able to use both experience and intuition to find solutions to second
and third order problems. Because of these subtle problems, most designers find that after the first paper
design is done, as many as four or five lab iterations may be necessary before the transformer meets the
design goals. However, there is a considerable design challenge in this area and a great deal of satisfaction
can be obtained by mastering it.
This component design, as do all others, begins by requesting all available literature from the
appropriate manufacturers and then following this up with phone calls when specific questions arise. A
partial list of companies is shown in Table 103. Designs below 20 W generally use pot cores, but for
20 W and above, E cores are preferred. E cores expose the windings to air so that heat is not trapped inside
and make it easier to bring out connections for several windings. Remember that flyback designs require
lower permeability cores than the others. The classic approach is to consult manufacturers charts like the
one shown in Figure 108 and then to pick a core with the required power handling ability. Both E and EC
(E cores with a round center leg) are popular now and they are available from several manufacturers. EC
cores offer a performance advantage (better coupling) but standard E cores cost less and are also used
in these applications. Another approach that seems to work equally well is to do a paper design of the
estimated windings and turns required. Size the wire for 500 circular mils (CM) per amp and then find a
core that has the required window area for this design. Now, before the windings are put on, it is a good
idea to modify the turns so that they fit on one layer or an integral number of layers on that bobbin. This
involves checking the turns per inch of the wire against the bobbin length. The primary generally goes on
first and then the secondaries. If the primary hangs over an extra half layer, try reducing the turns or the
wire size. Conversely, if the secondary does not take up a full layer, try bifilar winding (parallel) using wire
half the size originally chosen (i.e., 3 wire sizes smaller, like 23 versus 20). This technique ultimately results
in the use of foil for the higher current (20 A) low voltage windings. Most windings can be separated with
3 mil mylar (yellow) tape but for good isolation, cloth is recommended between primary and secondary.
Finally, once a mechanical fit has been obtained, it is time for the circuit tests. The isolation voltage
rating is strictly a mechanical problem and is one of the reasons why cloth is preferred over tape between
the primary and secondary. The inductance and saturating current level of the primary are inherent to the
design, and should be checked in the circuit or other suitable test fixture. Such a fixture is shown in
Figure 107 where the transistor and diode are sized to handle the anticipated currents. The pulse
generator is run at a low enough duty cycle to allow the core to reset. Pulse width is increased until the start
of saturation is observed (Isat). Inductance is found using L = E/(di/dt).
3892
Figure 106. Control Circuit Topologies

Rect &
Filter
Line
Rect &
Filter
Output
Dual Channel
Control
IC
(a) Single Chip System Drive Transformer Isolation
Line
Rect &
Filter
Rect &
Filter
Output
Single Channel
Control
IC
Opto
Coupler
Error
Amp
(b) Three Chip System Opto Coupler Isolation
In forward converters, the transformer generally has no gap in order to minimize the magnetizing
current (IM). For these applications the core should be chosen large enough so that the resulting LI product
insures that IM at operating voltages is less than Isat. For flyback designs, a gap is necessary and the test
circuit is useful again to evaluate the effect of the gap. The gap will normally be quite large, Lg > > Lm/u,
where, Lg
= gap length
Lm = magnetic path length, and
u
= permeability.
Under this stipulation, the gap directly controls the LI parameters and doubling it will decrease L by two and increase Isat by two
until fringing effects occur. Gaps of 5 mils to 20 mils are common. Again, the anticipated switching currents must be less than Isat
when the core is gapped for the correct inductance.
Table 103. Partial List of Core (C) and Transformer (T) Manufacturers
Company
Ferroxcube Inc.
Indiana General
Stackpole
TDK
Pulse Engineering
Coilcraft
Location
Code
Sauggerties, NY
Keasby, NJ
St. Marys, PA
El Segundo, CA
San Diego, CA
Cary, IL
C
C
C
C
T
T
Transformer tests in the actual supply are usually done with a high voltage dc power supply on the
primary and with a pulse generator or other manual control for the pulse width (such as using the control
IC in the open loop configuration). Here the designer must recheck three areas:
1. Core saturation
2. Correct amount of secondary voltage
3. Transformer heat rise
If problems are detected in any of these areas, the ultimate fix may be to redesign using the next larger
core size. However, if problems are minimal, or none exist, it is possible to stay with the same core or even
consider using the next smaller size.
3893
Figure 107. Simple Coil Tester

20V
DUT
Isat
IC
IC
Scope
Time
Current Transformer
IC
L = V t
Filter Capacitor Considerations

In todays 20 kHz switchers, aluminum electrolytics still predominate. The good news is that most have
been characterized, improved, and cost reduced for this application. The input filter requires a voltage
rating that depends on the peak line voltage; i.e., 400 V to 450 V for a 220 V switcher. If voltage is increased
beyond this point, the capacitor will begin to act like a zener and be thermally destroyed from high leakage
currents if the rating is exceeded for enough time. In doubler circuits, voltage sharing of the two capacitors
in series can be a problem. Here extra voltage capability may be needed to make up for the imbalances
caused by different values of capacitance and leakage current. A bleeder resistor is normally used here
not only for safety but to mask the differences in leakage current. The RMS current rating is also an
important consideration for input capacitors and is an example of improvements offered by todays
manufacturers. Earlier lytics usually lacked this rating and often overheated. Large capacitors that were
not needed for performance were used just to reduce this heating. However, todays devices offer lower
thermal resistance, improved connection to the foil and good RMS ratings. A partial list of manufacturers
that supply both high voltage input and the lower voltage output capacitors for switchers is shown in
Table 104. Most of the companies offer not only the standard 85C components, but devices with up to
125C ratings which are required because of the high ambient temperatures (55 to 85C) that many
switchers have to operate in, many times without the benefit of fans.
Table 104. Partial List of Capacitor Companies
Company (U.S.)
Location
MEPCO/Electra
Columbia, SC
CornellDublier
Sanford, NC
Sangamo
Pickens, SC
Mallory
Indianapolis, IN
For output capacitors the buzz word is low ESR (equivalent series resistance). It turns out that for most
capacitors even in the socalled low ESR series, the output ripple depends more on this resistance than
on the capacitor value itself. Although typical and maximum ESR ratings are now available on most
capacitors designed for switchers, the lead inductance generally is not specified except for the ultrahigh
frequency four terminal capacitors from some vendors. This parameter is responsible for the relatively high
switching spikes that appear at the output. However, at this point in time, most designers find it less costly
and more effective to add a high frequency noise filter rather than use a relatively expensive capacitor with
low equivalent series inductance (ESL).
These LC noise or spike filters are made using small powdered iron toroids (1/2 to 1 OD) with
distributed windings to minimize interwinding capacitance. And the output is bypassed using a small
0.1 F ceramic or a 10 F to 50 F tantalum or both. Larger powered iron toroids are often used in the
main LC output filter although the higher permeability ferrite EC and E cores with relatively large gaps can
also be used. Calculations for the size of this component should take into account the minimum load so
that the choke will not run dry as stated earlier.
3894
Figure 108. Core Selection for Bridge Configurations

(Reprinted from Ferroxcube Design Manual)
2000
Pth
(W)
1000
500
200
100
50
20
10
1
10
20
30
40
50
Note: Power handling decreases by a factor of 2 in forward

Note: and by 4 in flyback configurations.
3895
SECTION 11
SWITCHING REGULATOR COMPONENT
DESIGN TIPS
Transistors
The initial selection of a transistor for a switcher is basically a problem of finding the one with voltage
and current capabilities that are compatible with the application. For the final choice performance and cost
tradeoffs among devices from the same or several manufacturers have to be weighed. Before these
devices can be put in the circuit, both protective and drive circuits will have to be designed.
Motorolas first line of devices for switchers were trademarked Switchmode transistors and
introduced in the early 70s with data sheets that provided all the information that a designer would need
including reverse bias safe operating area (RBSOA) and performance at elevated temperature (100C).
The first series was the 2N6542 through 2N6547, TO204 (TO3) and was followed by the MJE13002
through MJE13009 series in a plastic TO220 package. Finally, high voltage (1.0 kV) requirements were
met by the metal MJ8500 thru MJ8505 series and the plastic MJE8500 series. The Switchmode II series
is an advanced version of Switchmode I that features faster switching. Switchmode III is a state of the art
bipolar with exceptional speed, RBSOA, and up to 1.5 kV blocking capacity. Here, device cost is somewhat
higher, but system costs may be lowered because of reduced snubber requirements and higher operating
frequencies. A similar argument applies to Motorola TMOS Power FETs. These devices make it possible
to switch efficiently at higher frequencies (200 kHz to 500 kHz) but the main selling point is that they are
easier to drive. This latter point is the one most often made to show that systems savings are again quite
possible even though the initial device cost is higher.
Table 111. Motorola High Voltage Switching Transistor Technologies
Approximate
Switching
Frequency
Typical
Device
Typical Fall
Time
SWITCHMODE I
2N6545
MJE13005
MJE12007
200 ns
to
500 ns
20 k
SWITCHMODE II
MJ13081
100 ns
100 k
SWITCHMODE III
MJ16010
50 ns
200 k
TMOS
MTP5N40
20 ns
500 k
Family
Table 112 is a chart of the transistor voltage requirements for the various offline converter circuits.
As illustrated, the most stringent requirement for single transistor circuits (flyback and forward) is the
blocking or VCEV rating. Bridge circuits, on the other hand, turn on and off from the dc bus and their most
critical voltage is the turnon or VCEO(sus) rating.
Table 112. Power Transistor Voltage Chart
Circuit
Line
Voltage
220
120
3896
Flyback, Forward or PushPull
Half or FullBridge
VCEV
VCEO(sus)
VCEO(sus)
VCEV
850 kV to 1.0 kV
450
450
250
450
250
450
250
Most switchmode transistor load lines are inductive during turnon and turnoff. Turnon is generally
inductive because the short circuit created by output rectifier reverse recovery times is isolated by leakage
inductance in the transformer. This inductance effectively snubs most turnon load lines so that the rectifier
recovery (or short circuit) current and the input voltage are not applied simultaneously to the transistor.
Sometimes primary interwinding capacitance presents a small current spike but usually turnon transients
are not a problem. Turnoff transients due to this same leakage inductance, however, are almost always
a problem. In bridge circuits, clamp diodes can be used to limit these voltage spikes. If the resulting
inductive load line exceeds the transistors reverse bias switching capability (RBSOA) then an RC network
may also be added across the primary to absorb some of this transient energy. The time constant of this
network should equal the anticipated switching time of the transistor (50 ns to 500 ns). Resistance values
of 100 to 1000 in this RC network are generally appropriate. Trial and error will indicate how low the
resistor has to be to provide the correct amount of snubbing. For single transistor converters, the circuits
shown in Figure 111 are generally used.
Here slightly different criteria are used to define the R and C snubber values:
I tf
C=
V
where;
I = the peak switching current
tf = the transistor fall time
V = the peak switching voltage (Approximately twice the DC bus)
also,
R = ton/C (it is not necessary to completely discharge this capacitor
in order to obtain the desired effects of this circuit)
where, ton = the minimum ontime or pulse width
and, PR = CV2f
2
where, PR = the power rating of the resistor
and,
f = the operating frequency.
In most of todays designs snubber elements are small or nonexistent and voltage spikes from energy
left in the leakage inductance a more critical problem depending on how good the coupling is between the
primary and clamp windings and how fast the clamp diode turns on. FETs often have to be slowed down
to prevent self destruction from this spike.
Figure 111. Protection Circuits for Switching Transistors
VDD
Clamp
Winding
Zener
Clamp
Zener
Clamp
RC
Snubber
RC
Network
RC
Clamp
3897
Zener and Mosorb Transient Suppressors

If necessary, protection from voltage spikes may be obtained by adding a zener and rectifier across
the primary as shown in Figure 111. Here Motorolas 5.0 W zener lines with ratings up to 200 V, and 10 W
TO220 Mosorbs with ratings up to 250 V can provide the clamping or spike limiting function. If the zener
must handle most of the power, its size can be estimated using:
LL I2f
PZ =
2
where, PZ = the zener power rating
and,
LL = the leakage inductance (measured with the clamp winding or secondary shorted)
I = peak collector current
f = operating frequency
Distinction is sometimes made between devices trademarked Mosorb (by Motorola, Inc.), and
standard zener/avalanche diodes used for reference, lowlevel regulation and lowlevel protection
purposes. It must be emphasized that Mosorb devices are, in fact, zener diodes. The basic semiconductor
technology and processing are identical. The primary difference is in the applications for which they
are designed. Mosorb devices are intended specifically for transient protection purposes and are
designed, therefore, with a large effective junction area that provides high pulse power capability while
minimizing the total silicon use. Thus, Mosorb pulse power ratings begin at 600 W well in excess of low
power conventional zener diodes which in many cases do not even include pulse power ratings among
their specifications.
MOVs, like Mosorbs, do have the pulse power capabilities for transient suppression. They are metal
oxide varistors (not semiconductors) that exhibit bidirectional avalanche characteristics, similar to those
of backtoback connected zeners. The main attributes of such devices are low manufacturing cost, the
ability to absorb high energy surges (up to 600 joules) and symmetrical bidirectional breakdown
characteristics. Major disadvantages are: high clamping factor, an internal wearout mechanism and an
absence of lowend voltage capability. These limitations restrict the use of MOVs primarily to the protection
of insensitive electronic components against high energy transients in applications above 20 V, whereas,
Mosorbs are best suited for precise protection of sensitive equipment even in the low voltage range the
same range covered by conventional zener diodes.
Rectifiers
Once components for the inverter section of a switcher have been chosen, it is time to determine how
to get power into and out of this section. This is where the allimportant rectifier comes into play. (See
Figure 112.) The input rectifier is generally a standard recovery bridge that operates off the ac line and
into a capacitive filter. For the output section, most designers use Schottkys for efficient rectification of
the low voltage, 5.0 V output windings and for the higher voltage, 12 V to 15 V outputs, the more economical
fast recovery or ultrafast diodes are used.
Figure 112. Switchmode Power Supply Flyback or Boost Design
D4
12V Output
D2
D5
D1
AC Line
Cont
IC
D3
Q1
3898
5V Output
TMOS1
OC
D1
D2
D3
D4
D5
Bridge Rectifier
Clamp Diode
Snubber Diode
Output Rectifier
Output Rectifier
Line Voltage
HV/FastUltrafast
HV/FastUltrafast
Fast/Ultrafast
Schottky
For the process of choosing an input rectifier, it is useful to visualize the circuit shown in Figure 113.
To reduce cost, most earlier approaches of using choke input filters, soft start relays (Triacs), or SCRs to
bypass a large limiting resistor have been abandoned in favor of using small limiting resistors or thermistors
and a large bridge. The bridge must be able to withstand the surge currents that exist from repetitive starts
at peak line. The procedure for finding the right component and checking its fit is as follows:
1. Choose a rectifier with 2 to 5 times the average IO required.
2. Estimate the peak surge current (Ip) and time (t) using:
1.4 Vin
Ip =
t = RSC
RS
Where Vin is the RMS input voltage; RS is the total series resistance; and C is the filter capacitor size.
Figure 113. Choosing Input Rectifiers
Filter
Cap
Bridge
RS
AC
Line
Load
3. Compare this current pulse to the sub cycle surge current rating (IS) of the diode itself. If the curve
of IS versus time is not given on the data sheet, the approximate value for IS at a particular pulse
width (t) may be calculated knowing:
IFSM the single cycle (8.3 ms) surge current rating and using.
I2 t = K, which applies when the diode temperature rise is controlled by its
thermal response as well as power (i.e., T = KP t for t < 8.0 ms).
This gives:
1/4
IS2 t = I2FSM 8.3 ms or, IS = IFSM ( 8.3 ms ) , t is in milliseconds.
t
4. If IS < IP, consider either increasing the limiting resistor (RS) or utilizing a larger diode.
In the output section where high frequency rectifiers are needed, there are several types available to
the designer. In addition to the Schottky (SBR) and fast recovery (FR), there is also an ultrafast recovery
(UFR). Comparative performance for devices with similar current ratings is shown in Table 113. The
obvious point here is that lower forward voltage improves efficiency and lower recovery times reduce
turnon losses in the switching transistors, but the tradeoff is higher cost. As stated earlier, Schottkys are
generally used for 5.0 V outputs and fast recovery and ultrafast devices for 12 V outputs and greater. The
ultrafast is competing both with the Schottky where higher breakdown is needed and with the fast recovery
in those applications where performance is more important than cost. Ten years ago Schottkys were very
fragile and could fail short from either excessive dv/dt (1.0 V to 5.0 V per nanosecond) or reverse
avalanche. Since that time, Motorola has incorporated a guard ring or internal zener which minimizes
these earlier problems and reduces the need for RC snubbers and other external protective networks.
Table 113. Motorola Rectifier Product Portfolio
Parameter
Forward Voltage (VF)
Reverse Recovery Time (trr)
trr Form
DC Blocking Voltage (VR)
Cost Ratio
Ultrafast
Fast
Recovery
Standard
Recovery
0.5 V to 0.6 V
0.9 V to 1.0 V
1.2 V to 1.4 V
1.2 V to 1.4 V
<10 ns
25 ns to 100 ns
150 ns
1.0 s
Soft
Soft
Soft
Soft
20 V to 60 V
50 V to 1000 V
50 V to 1000 V
50 V to 1000 V
3:1
3:1
2:1
1:1
Schottky
3899
SECTION 12
BASIC SWITCHING POWER SUPPLY
CONFIGURATIONS
The implementation of switching power supplies by the nonspecialist is becoming increasingly easy
due to the availability of power devices and control ICs especially developed for this purpose by the
semiconductor manufacturer.
This section is meant to help in the preliminary selection of the devices required for the implementation
of the listed switching power supplies.
Flyback and Forward Converter Switching Power Supplies (50 W to 250 W)
Input line variation: Vin + 10%, 20%

Converter efficiency: = 80%
Output regulation by duty cycle ( variation: (max) = 0.4)
Maximum Transistor working current:
Iw =
2.0 Pout
(max) Vin(min) 2
Pout
5.5 Pout
(Flyback)
Vin
2.25 Pout
(max) Vin(min) 2 Vin (Forward)

Maximum transistor working voltage: Vw = 2 Vin(max) 2 + guardband
=
Working frequency: f = 20 kHz to 200 kHz
Basic Flyback Configuration

Output
Rectifier
DC Output
Power
Inverter
Line
Input
Input
Rectifier
3900
Control
Circuitry
Table 121. Flyback and Forward Converter Semiconductor Selection Chart

Output Power
50 W
100 W
175 W
250 W
Input Line Voltage (Vin)
120 V
220 V
240 V
120 V
220 V
240 V
120 V
220 V
240 V
120 V
MOSFET Requirements:
Max Working Current (Iw)
Max Working Voltage (Vw)
2.25 A
380 V
1.2 A
750 V
4.0 A
380 V
2.5 A
750 V
8.0 A
380 V
4.4 A
750 V
11.4 A
380 V
Power MOSFETs Recommended:

Metal (TO204AA) (TO3)
Plastic (TO220AB)
Plastic (TO218AC)
MTM4N45
MTP4N45
MTM2N90
MTP2N90
MTM4N45
MTP4N45
MTM2N90
MTP2N90
MTM7N45
MTH7N45
MTM4N90
MTM15N45
Input Rectifiers:
Recommended Types
0.4 A
MDA104A
0.25 A
MDA106A
0.4 A
MDA206
0.5 A
MDA210
2.35 A
MDA970
1.25 A
MDA210
4.6 A
MDA3506
Output Rectifiers:
Recommended types for
Output Voltage of: 5.0 V
10 V
20 V
50 V
100 V
Recommended Control Circuits
MBR3035PT
MUR3010PT
MUR1615CT
MUR1615CT
MUR 440, MUR840A
MBR3035PT
MUR3010PT
MUR1615CT
MUR1615CT
MUR840A
MBR12035CT
MUR10010CT
MUR3015PT
MUR1615CT
MUR840A
MBR20035CT
MUR10010CT
MUR10015CT
MUR3015PT
MUR840A
SG1525A, SG1526, TL494 Inverter Control Circuit

MC3423 Overvoltage Detector
Error Amplifier: Single TL431; DualLM358
Quad MC3403, LM324, LM2902
Flyback and Forward Converters

To take advantage of the regulating techniques discussed earlier and also provide isolation, a total of
seven popular configurations have evolved and are listed below. Each circuit has a practical power range
or capability associated with it as follows:
Circuit
Power Range
Parts Cost
DC Converter
5.0 W
$ 4.00
Converter w/30 V Transformer
10 W
7.00
Blocking OSC
20 W
10.00
Flyback
50 W
15.00
Forward
100 W
20.00
HalfBridge
200 W
30.00
FullBridge
500 W
75.00
First to be discussed will be the low power (20 W to 200 W) converters which are dominated by the
single transistor circuits shown in Figure 121. All of these circuits operate the magnetic element in the
unipolar rather than bipolar mode. This means that transformer size is sacrificed for circuit simplicity.
The flyback (alternately known as the ringing choke) regulator stores energy in the primary winding
and dumps it into the secondary windings, see Figure 121(a). A clamp winding is usually present to allow
energy stored in the leakage reactance to return safely to the line instead of avalanching the switching
transistor. The operating model for this circuit is the buckboost discussed earlier. The flyback is the lowest
cost regulator because output filter chokes are not required since the output capacitors feed from a current
source rather than a voltage source. It does have higher output ripple than the forward converters because
of this. However, it is an excellent choice when multiple output voltages are required and does tend to
provide better cross regulation than the other types. In other words changing the load on one winding will
have little effect on the output voltage of the others.
3901
Figure 121. Low Power Popular (20 to 200 W) Converter Configurations
(a) Flyback (Clamp Winding is Optional)
(b) Forward (Clamp Winding is Necessary)
(c) Two Transistor Forward or Flyback

(Clamp Winding is not Needed)
A 120/220 Vac flyback design requires transistors that block twice the peak line plus transients or about
1.0 kV. Motorolas MJE13000 and 16000A series with ratings of 750 V to 1000 V are normally used here.
These bipolar devices are relatively fast (100 ns) and are typically used in the 20 kHz to 50 kHz operating
frequency range. The recent availability of 900 V and 1000 V TMOS FETs allows designers to operate in
the next higher range (50 kHz to 80 kHz) and some have even gone as high as 300 kHz with square wave
designs and FETs. Faster 1.0 kV bipolar transistors are also planned in the future and will provide another
design alternative. The two transistor variations of this circuit, Figure 121(c), eliminate the clamp winding
and add a transistor and diode to effectively clamp peak transistor voltages to the line. With this circuit a
designer can use the faster 400 V to 500 V FET transistors and push operating frequencies considerably
higher. There is a cost penalty here over the single transistor circuit due to the extra transistor, diodes and
gate drive circuitry.
A subtle variation in the method of operation can be Figure 122. Flyback Transistor Waveforms
applied to the flyback regulator. The difference is referred
800 V
to as operation in the discontinuous or continuous mode
and the waveform diagrams are shown in Figure 122.
VCE
400 V VCE
The analysis given in the earlier section on boost
0V
regulators dealt strictly with the discontinuous mode
where all the energy is dumped from the choke before the
2.0 A
1.0 A
transistor turns on again. If the transistor is turned on while
IC
0 A IC
energy is still being dumped into the load, the circuit is
Discontinuous
Mode
Continuous Mode
operating in the continuous mode. This is generally an
advantage for the transistor in that it needs to switch only
half as much peak current in order to deliver the same
power to the load. In many instances, the same transformer
transformer may be used with only the gap reduced to provide more inductance. Sometimes the core size
will need to be increased to support the higher LI product (2 to 4 times) now required because the
inductance must increase by almost 10 times to effectively reduce the peak current by two. In dealing with
the continuous mode, it should also be noted that the transistor must now turn on from 500 V to 600 V rather
than 400 V level because there no longer is any deadtime to allow the flyback voltage to settle back down
in the input voltage level. Generally, it is advisable to have VCEO(sus) ratings comparable to the turnon
requirements except for SMIII where turnon up to VCEV is permitted.
The flyback converter stands out from the others in its need for a low inductance, high current primary.
Conventional E and pot core ferrites are difficult to work with because their permeability is too high even
with relatively large gaps (50 to 100 milliinches). The industry needs something better that will provide
permeabilities of 60 to 120 instead of 2000 to 3000 for this application.
3902
The single transistor forward converter is shown in Figure 121(b). Although it initially appears very
similar to the flyback, it is not. The operating model for this circuit is actually the buck regulator discussed
earlier. Instead of storing energy in the transformer and then delivering it to the load, this circuit uses the
transformer in the active or forward mode and delivers power to the load while the transistor is on. The
additional output rectifier is used as a freewheeling diode for the LC filter and the third winding is actually
a reset winding. It generally has the same turns as the primary, (is usually bifilar wound) and does clamp
the reset voltage to twice the line. However, its main function is to return energy stored in the magnetizing
inductance to the line and thereby reset the core after each cycle of operation. Because it takes the same
time to set and reset the core, the duty cycle of this circuit cannot exceed 50%. This also is a very popular
low power converter and like the flyback is practically immune from transformer saturation problems.
Transistor waveforms shown in Figure 123 illustrate
Figure 123. Forward Converter
that the voltage requirements are identical to the
Transistor Waveforms
flyback. For the single transistor versions, 400 V
turnon and 1.0 kV blocking devices like the MJE13000
800 V
and MJE16000 transistors are required. The two
VCE
400 V
transistor circuit variations shown in Figure 121(b)
again adds a cost penalty but allows a designer to use
0V
the faster 400 V to 500 V devices. With this circuit,
operation in the discontinuous mode refers to
1.0 A
the time when the load is reduced to a point where the
IC
filter choke runs dry. This means that choke current
0A
starts at and returns to zero during each cycle of
operation. Most designers prefer to avoid this type
of mode because of higher ripple and noise even though there are no adverse effects on the components
themselves. Standard ferrite cores work fine here and in the high power converters as well. In these
applications, no gap is used as the high permeability (3000) results in the desirable effect of very low
magnetizing current levels. And, zeners or RC clamps may be used to reset the core in lieu of the clamp
winding to lower the voltage stress on the switching transistors.
PushPull and Bridge Converters
Figure 124. PushPull Converter

(200 W to 1.0 kW)
The high power circuits shown in Figures 124 to

127 all operate the magnetic element in the bipolar or
+ Vout
+ Vin
pushpull mode and require 2 to 4 inverter transistors.
Because the transformers operate in this mode they
tend to be almost half the size of the equivalent single
transistor converters and thereby provide a cost
advantage over their counterparts at power levels of
200 kW to 1.0 kW.
The pushpull converter shown in Figure 124 is
one of the oldest converter circuits around. Its early use
was in low voltage inverters such as the 12 Vdc to 120 Vdc power source for recreational vehicles and in
dc to dc converters. Because these converters are free running rather than driven and operate from low
voltages, transformer saturation problems are minimal. In the high voltage offline switchers, saturation
problems are common and were difficult to solve. The transistors are also subjected to twice the peak line
voltage which requires the use of high voltage (1.0 kV) transistors. Both of these drawbacks have tended
to discourage designers of offline switchers from using this configuration until current mode control ICs
were introduced. Now these circuits are being looked at with renewed interest.
3903
PushPull Switching Power Supplies (100 W to 500 W)

Output regulation by duty cycle () variation: (max) = 0.8
Maximum transistor working current:
Pout
1.4 Pout
Iw =
=
Vin
(max) Vin(min) 2
Maximum transistor working voltage: Vw = 2
Vin(max)
2 + guardband
Basic PushPull Configuration

Output
Filter
Output
Rectifier
DC Output
Line
Input
Control
Circuitry
Power
Inverter
Input
Rectifier
Table 122. PushPull Semiconductor Selection Chart

Output Power
100 W
250 W
500 W
Input Line Voltage (Vin)
120 V
220 V
240 V
120 V
220 V
240 V
120 V
220 V
240 V
1.2 A
380 V
0.6 A
750 A
2.9 A
380 V
1.6 A
750 V
5.7 A
380 V
3.1 A
750 V
MTM2N50
MTP2N45
MTM2N90
MTP2N90
MTM4N45
MTP4N45
MTM2N90
MTP2N94
MTM7N45
MTH7N45
MTM4N90
Input Rectifiers:
Recommended Types
0.9 A
MDA206
0.5 A
MDA210
2.35 A
MDA9705
1.25 A
MDA210
4.6 A
MDA3506
2.5 A
MDA3510
Output Rectifiers:
output voltages of: 5.0 V
10 V
20 V
50 V
100 V
MBR3035PT
MBR3045PT, MUR3010PT
MUR1615CT
MUR1615CT
MUR840A, MUR440

Plastic (TO220AB)
Plastic (TO218AC)
3904
MBR12035CT
MUR10010CT
MUR3015PT
MUR1615CT
MUR840A
MBR20035CT
MUR10010CT
MUR10015CT
MUR3015PT
MUR840A

Quad MC3403, LM324, LM2902
HalfBridge/FullBridge Switching Power Supplies (100 W to 500 W/500 W to 1000 W)

Output regulation by duty cycle () variation: (max) = 0.8
Maximum working current:
2 Pout
2.8 Pout
=
Iw =
(HalfBridge)
Vin
(max) Vin(min) 2
Pout
1.4 Pout
(FullBridge)
Vin
2
(max) Vin(min)
Maximum transistor working voltage: Vw = Vin(max)
2 + guardband
Basic HalfBridge Configuration

Output
Filter
Output
Rectifier
Line
Input
DC Output
Control
Circuitry
Power
Inverter
Input
Rectifier
Table 123. HalfBridge Semiconductor Selection Chart

Output Power
100 W
350 W
500 W
Input Voltage (Vin)
120 V
220 V
240 V
120 V
220 V
240 V
120 V
220 V
240 V
2.3 A
190 V
1.25 A
380 V
5.7 A
190 V
3.1 A
380 V
11.5 A
190 V
6.25 A
380 V
MTM5N35
MTP3N40
MTM2N45
MTP2N45
MTM8N40
MTH8N40
MTM4N45
MTP4N45
MTM10N25
MTP10N25
MTM7N45
MTH7N45
Input Rectifiers:
Recommended Types
0.9 A
MDA206
0.5 A
MDA210
2.3 A
MDA9705
1.25 A
MDA210
4.6 A
MDA3506
2.5 A
MDA3510
Output Rectifiers:
output voltage of: 5.0 V
10 V
20 V
50 V
100 V
MBR3035PT
MBR3045PT, MUR3010PT
MUR1615CT
MUR1615CT
MUR840A, MUR440

Plastic (TO220AB)
Plastic (TO218AC)
MBR12035CT
MUR10010CT
MUR3015PT
MUR1615CT
MUR840A
MBR20035CT
MUR10010CT
MUR10015CT
MUR3015PT
MUR840A

Quad MC3403, LM324, LM2902
3905
Half and FullBridge

The most popular high power converter is the halfbridge (Figure 126). It has two clear advantages
over the pushpull and became the favorite rather quickly. First, the transistors never see more than the
peak line voltage and the standard 400 V fast switchmode transistors that are readily available may be
used. And second, and probably even more important, transformer saturation problems are easily
minimized by use of a small coupling capacitor (about 2.0 F to 5.0 F) as shown above. Because the
primary winding is driven in both directions, a fullwave output filter, rather than half, is now used and the
core is actually utilized more effectively. Another more subtle advantage of this circuit is that the input filter
capacitors are placed in series across the rectified 220 V line which allows them to be used as the voltage
doubler elements on a 120 V line. This still allows the inverter transformer to operate from a nominal
320 V bus when the circuit is connected to either 120 V or 220 V. Finally, this topology allows diode clamps
across each transistor to contain destructive switching transients. The designers dream, of course, is for
fast transistors that can handle a clamped inductive load line at rated current. And a few (like the MJE16000
series from Motorola) are beginning to appear on the market. With the improved RBSOA that these
transistors feature, less snubbing is required and this improves both the cost and efficiency of
these designs.
Figure 125. HalfBridge Converter

with Split Windings
Figure 126. HalfBridge Converter

(200 W to 1.0 kW)
+ Vin
+ Vin
+ Vout
CC
+ Vout
CC
Basic FullBridge Configuration

Output
Filter
Output
Rectifier
DC Output
Control
Circuitry
Line
Input
Power
Inverter
Input
Rectifier
3906
Table 124. FullBridge Semiconductor Selection Chart

Output Power
500 W
750 W
1000 W
Input Voltage (Vin)
120 V
220 V
240 V
120 V
220 V
240 V
120 V
220 V
240 V
Max Working Curren (Iw)
5.7 A
190 V
3.1 A
380 V
8.6 A
190 V
4.7 A
380 V
11.5 A
190 V
6.25 A
380 V

Plastic (TO220AB)
Plastic (TO218AC)
MTM8N20
MTP8N20
MTM4N45
MTP4N45
MTM10N25
MTP10N25
MTM7N45
MTP4N45
MTH7N45
MTM15N20
MTP12N20
MTH15N20
MTM7N45
MTH7N45
Input Rectifiers:
Recommended Types
4.6 A
MDA3506
2.5 A
MDA3510
7.0 A
3.8 A
9.25 A
5.0 A
Output Rectifiers:
output voltage of: 5.0 V
10 V
20 V
50 V
100 V
MBR20035CT
MUR10010CT
MUR10015CT
MUR3015PT
MUR804PT
MBR30035CT
MUR10010CT*
MUR10015CT
MUR3015PT*
MUR3040PT
MBR30035CT*
MUR10010CT*
MUR10015CT*
MUR10015CT
MUR3040PT

Quad MC3403, LM324, LM2902
*More than one device per leg, matched.
The effective current limit of todays low cost TO218 discrete transistors (250 mil die) is somewhere
in the 10 A to 20 A area. Once this limit is reached, the designer generally changes to the fullbridge
configurations shown in Figure 127. Because full line rather than half is applied to the primary winding,
the power out can be almost double that of the halfbridge with the same switching transistors. Power
Darlington transistors are a logical choice for higher power control with current, voltage and speed
capabilities allowing very high performance and cost effective designs. Another variation of the halfbridge
is the split winding circuit, shown in Figure 125. A diode clamp can protect the lower transistor but a
snubber or zener clamp must still be used to protect the top transistor from switching transients. Because
both emitters are at an ac ground point, expensive drive transformers can now be replaced by lower cost
capacitivelycoupled drive circuits.
Figure 127. FullBridge Converter

(200 W to 1.0 kW)
+ Vin
+ Vout
CC
3907
SECTION 13
SWITCHING REGULATOR DESIGN EXAMPLES
In addition to the application materials in this data book, Motorola publishes several application notes
which contain basic information on the design of power supplies using a variety of Motorola Analog ICs.
AN920 describes in detail the principles of operation of the MC34063A and A78S40 Switching Regulator
Subsystems. Several converter design examples and numerous applications circuits with test data are
included in this application note. The circuit techniques described in this note are also applicable to the
MC34163 and MC34165 Power Switching Regulators.
Operating details of the MC34129 Current Mode Switching Regulator Controller, and examples of its
use with Motorola SENSEFET products, are provided in AN976. The application note AN983 focuses
on a 400 W half-bridge power supply design which uses the TL494 PWM control circuit. The TL594 can
be used in this same application.
Essentially all of the data sheets for newer power supply control and supervisory circuits include
extensive applications information with test conditions and performance results. Many data sheets also
include printed circuit board layouts for some key applications so that the designer can evaluate the
integrated circuits in an actual power supply. This data book presents all data sheets in their entirety so
that the applications information is readily available for each device.
3908
SECTION 14
POWER SUPPLY SUPERVISORY
AND PROTECTION CONSIDERATIONS
The use of SCR crowbar overvoltage protection (OVP) circuits has been, for many years, a popular
method of providing protection from accidental overvoltage stress for the load. In light of the recent
advances in LSI circuitry, this technique has taken on added importance. It is not uncommon to have
several hundred dollars worth of electronics supplied from a single low voltage supply. If this supply were
to fail due to component failure or other accidental shorting of higher voltage supply busses to the low
voltage bus, several hundred dollars worth of circuitry could literally go up in smoke. The small additional
investment in protection circuitry can easily be justified in such applications.
A. The Crowbar Technique

One of the simplest and most effective methods of obtaining overvoltage protection is to use a
crowbar SCR placed across the equipments dc power supply bus. As the name implies, the SCR is used
much like a crowbar would be, to short the dc supply when an overvoltage condition is detected. Typical
circuit configurations for this circuit are shown on Figure 141. This method is very effective in eliminating
the destructive overvoltage condition. However, the effectiveness is lost if the OVP circuitry is not reliable.
Figure 141. Typical Crowbar OVP Circuit Configurations
Vout
Vin
DC
Power
Supply
+
Cout
Vin
DC
Power
Supply
OV
Sense
Vout
Cout
OV
Sense
*Needed if supply not currentlimited.
3909
Figure 142. Crowbar SCR Surge Current Waveform

I
Ipk
di
dt
Surge Due to
Output Capacitor
Current Limited
Supply Output
B. SCR Considerations
Referring to Figure 141, it can easily be seen that, when activated, the crowbar SCR is subjected to
a large current surge from the filter and output capacitors. This large current surge, illustrated in Figure
142, can cause SCR failure or degradation by any one of three mechanisms: di/dt, peak surge current,
or I2 t. In many instances the designer must empirically determine the SCR and circuit elements which will
result in reliable and effective OVP operation. To aid in the selection of devices for this application, Motorola
has characterized several devices specifically for crowbar applications. A summary of these specifications
and a selection guide for this application is shown in Table 141. This significantly reduces the amount of
empirical testing that must be done by the designer. A good understanding of the factors that influence the
SCRs di/dt and surge current capability will greatly simplify the total circuit design task.
Table 141. Crowbar SCRs
Device Type**
Peak Discharge Current*
di/dt*
MCR67
MCR68
MCR69
MCR70
MCR71
300 A
300 A
750 A
850 A
1700 A
75 A/s
75 A/s
100 A/s
100 A/s
200 A/s
* tw = 1.0 s, exponentially decaying

** All devices available with 25, 50, and 100 V ratings
1. di/dt As the gate region of the SCR is driven on, its area of conduction takes a finite amount of time
to grow, starting as a very small region and gradually spreading. Since the anode current flows through
this turnedon gate region, very high current densities can occur in the gate region if high anode currents
appear quickly (di/dt). This can result in immediate destruction of the SCR or gradual degradation of its
forward blocking voltage capabilities, depending upon the severity of the occasion.
The value of di/dt that an SCR can safely handle is influenced by its construction and the characteristics
of the gate drive signal. A centergatefire SCR has more di/dt capability than a cornergatefire type, and
heavily overdriving (3 to 5 times IGT) the SCR gate with a fast <1.0 s rise time signal will maximize its di/dt
capability. A typical maximum di/dt in phase control SCRs of less than 50 A rms rating might be 200 A/s,
assuming a gate current of five times IGT and <1.0 s rise time. If having done this, a di/dt problem still
exists, the designer can also decrease the di/dt of the current saveform by adding inductance in series with
the SCR, as shown in Figure 143. Of course, this reduces the circuits ability to rapidly reduce the dc bus
voltage, and a tradeoff must be made between speedy voltage reduction and di/dt.
3910
2. Surge Current If the peak current and/or the duration of the surge is excessive, immediate
destruction due to device overheating will result. The surge capability of the SCR is directly proportional
to its die area. If the surge current cannot be reduced (by adding series resistance, see Figure 143) to
a safe level which is consistent with the systems requirements for speedy bus voltage reduction, the
designer must use a higher current SCR. This may result in the average current capability of the SCR
exceeding the steady state current requirements imposed by the dc power supply.
Figure 143. Circuit Elements Affecting SCR Surge & di/dt
RLead
ESR
Output
Capacitor
ESL
LLead
R*
L*
*R and L
empirically
determined
(For additional information on SCRs in crowbar applications refer to Characterizing the SCR for Crowbar Applications,
Al Pshaenich, Motorola AN789).
C. The Sense and Drive Circuit

In order to maximize the crowbar SCRs di/dt capability, it should receive a fast rise time
highamplitude gatedrive signal. This must be one of the primary factors considered when selecting the
sensing and drive circuitry. Also important is the sense circuitrys noise immunity.
Noise immunity can be a major factor in the selection of the sense circuitry employed. If the sensing
circuit has low immunity and is operated in a noisy environment, nuisance tripping of the OVP circuit can
occur on short localized noise spikes, which would not normally damage the load. This results in excessive
system down time. There are several types of sense circuits presently being used in OVP applications.
These can be classified into three types: zener, discrete, and 723.
Figure 144. The Zener Sense Circuit
1. The Zener Sense Circuit Figure 144 shows the use of

a zener to trigger the crowbar SCR. This method is NOT
recommended since it provides very poor gate drive and greatly
decreases the SCRs di/dt handling capability, especially since
the SCR steals its own very necessary gate drive as it turns on.
Additionally, this method does not allow the trip point to be
adjusted except by zener replacement.
NO!
2. The Discrete Sense Circuit A technique which can

provide adequate gate drive and an adjustable, low
temperature coefficient trip point is shown in Figure 145.
While overcoming the disadvantages of the zener sense circuit, this technique requires many components
and is more costly. In addition, this method is not particularly noise immune and often suffers from nuisance
tripping.
3. The 723 Sense Circuit By using an integrated circuit voltage regulator, such as the industry
standard 723 type, a considerable reduction in component count can be achieved. This is illustrated in
Figure 146. Unfortunately, this technique is not noise immune, and suffers an additional disadvantage in
that it must be operated at voltages above 9.5 V.
3911
Figure 145. The Discrete Sense Circuit
Figure 146. The 723 Sense Circuit
4. The MC3423 To fill the need for a low cost, low complexity method of implementing crowbar
overvoltage protection which does not suffer the disadvantages of previous techniques, an IC has been
developed for use as an OVP sense and drive circuit, the MC3423.
The MC3423 was designed to provide output currents of up to 300 mA with a 400 mA/s rise time in
order to maximize the di/dt capabilities of the crowbar SCR. In addition, its features include:
1. Operation off 4.5 V to 40 V supply voltages.
2. Adjustable low temperature coefficient trip point.
3. Adjustable minimum overvoltage duration before actuation to reduce nuisance
tripping in noisy environments.
4. Remote activation input.
5. Indication output.
5. Block Diagram The block diagram of the MC3423 is shown in Figure 147. It consists of a stable
2.6 V reference, two comparators and a high current output. This output, together with the indication output
transistor, is activated either by a voltage greater than 2.6 V on Pin 3 or by a TTL/5.0 V CMOS high logic
level on the remote activation input, Pin 5.
The circuit also has a comparatorcontrolled current source which can be used in conjunction with and
external timing capacitor to set a minimum overvoltage duration (0.5 s to 1.0 ms) before actuation occurs.
This feature allows the OVP circuit to operate in noisy environments without nuisance tripping.
Figure 147. MC3423 Block Diagram
VCC
Current
Source
4
2
Vsense 1
Vref
2.5 V
8
Output
7
VEE
3912
3
Vsense 2
5
RMT.
ACT.
6
Indication
Out
6. Basic Circuit Configuration The basic circuit configuration of the MC3423 OVP is shown in
Figure 148. In this circuit the voltage sensing inputs of both the internal amplifiers are tied together for
sensing the overvoltage condition. The shortest possible propagation delay is thus obtained. The threshold
or trip voltage at which the MC3423 will trigger and supply gate drive to the crowbar SCR, Q1, is determined
by the selection of R1 and R2. Their values can be determined by the equations given in Figure 148 or
by the graph shown in Figure 149. The switch (S1) shown in Figure 148 may be used to reset the SCR
crowbar. Otherwise, the power supply, across which the SCR is connected, must be shut down to reset
the crowbar. If a non currentlimited supply is used a fuse or circuit breaker, F1, should be used to protect
the SCR and/or the load.
Figure 148. MC3423 Basic Circuit Configuration
(+)
*
F1
(+ Sense Lead)
R1
Power
Supply
Q1
MC3423
3
R2
To
Load
RG
7
S1*
( Sense Lead)
()
R
R1
) 2.6 V (1 + 1 )
R2
R2
R2 10 k for minimum drift
Vtrip = Vref (1 +
*Needed if supply is not currentlimited
7. MC3423 Programmable Configuration In many instances, MC3423 OVP will be used in a noisy
environment. To prevent false tripping of the OVP circuit by noise which would not normally harm the load,
MC3423 has a programmable delay feature. To implement this feature, the circuit configuration of
Figure 1410 is used.
Here a capacitor is connected from Pin 3 and Pin 4 to VEE. The value of this capacitor determines the
minimum duration of the overvoltage condition (tD) which is necessary to trip the OVP. The value of CD can
be found from Figure 1411. The circuit operates in the following manner: when VCC rises above the trip
point set by R1 and R2, the internal current source begins charging the capacitor, CD, connected to Pins
3 and 4. If the overvoltage condition remains present long enough for the capacitor voltage, VCD to reach
Vref, the output is activated. If the overvoltage condition disappears before this occurs, the capacitor is
discharged at a rate 10 times faster than the charging rate, resetting the timing feature until the next
overvoltage condition occurs.
8. Indication Output An additional output for use as an indicator of OVP activation is provided by the
MC3423. This output (Pin 6) is an opencollector transistor which saturates when the MC3423 OVP is
activated. It will remain in a saturated state until the SCR crowbar pulls the supply voltage, VCC, below
4.5 V as in Figure 1410. This output can be used to clock an edge triggered flipflop whose output inhibits
or shuts down the power supply when the OVP trips. This reduces or eliminates the heatsinking
requirements for the crowbar SCR.
3913
Figure 149. R1 versus Trip Voltage

for the MC3423 OVP
Figure 1410. MC3423 Configuration for

Programmable Minimum Duration of
Overvoltage Condition Before Tripping
(+)
R1, RESISTANCE (k )
30
Max
R3
Typ
R1
1 6
R2 = 2.7 k
20
Power
Supply
Min
MC3423
3
R2
10
RG
Indication
Out
7
CD
5.0
10
15
20
Vtrip, TRIP VOLTAGE (V)
25
()
30
Vtrip
R3
10 mA
9. Remote Activation Input Another feature of the MC3423 is its Remote Activation Input, Pin 5. If the
voltage on this CMOS/TTL compatible input is held below 0.7 V, the MC3423 operates normally. However,
if it is raised to a voltage above 2.0 V, the OVP output is activated independent of whether or not an
overvoltage condition is present.
This feature can be used to accomplish an orderly and sequenced shutdown of system power supplies
during a system fault condition. In addition, the Indication Output of one MC3423 can be used to activate
another MC3423, if a single transistor inverter is used to interface the formers Indication Output to the
latters Remote Activation Input.
D. MC3425 Power Supply Supervisory Circuit

In addition to the MC3423 a second IC, the MC3425 has been developed. Similar in many respects
to the MC3423, the MC3425 is a power supply supervisory circuit containing all the necessary functions
required to monitor over and undervoltage fault conditions. The block diagram is shown below in
Figure 1412. The Overvoltage (OV) and Undervoltage (UV) Input Comparators are both referenced to
an internal 2.5 V regulator. The UV Input Comparator has a feedback activated 12.5 A current sink (IH)
which is used for programming the input hysteresis voltage (VH). The source resistance feeding this input
(RH) determines the amount of hysteresis voltage by VH = IHRH = 12.5 106 RH.
Figure 1411. CD versus Minimum Overvoltage Duration, tD for The MC3423 OVP
C D, CAPACITANCE ( F)
1.0
0.1
0.01
0.001
0.0001
0.001
3914
0.01
0.1
tD, DELAY TIME (ms)
1.0
10
Separate Delay pins (OV DLY, UV DLY) are provided for each channel to independently delay the Drive
and Indicator outputs, thus providing greater input noise immunity. The two Delay pins are essentially the
outputs of the respective input comparators, and provide a constant current source, IDLY(source), of typically
200 A when the noninverting input voltage is greater than the inverting input level. A capacitor connected
from these Delay pins to ground, will establish a predictable delay time (tDLY) for the Drive and Indicator
outputs. The Delay pins are internally connected to the noninverting inputs of the OV and UV Output
Comparators, which are referenced to the internal 2.5 V regulator. Therefore, delay time (tDLY) is based
on the constant current source, IDLY(source), charging the external delay capacitor (CDLY) to 2.5 V.
Vref CDLY
2.5 CDLY
tDLY =
=
= 12500 CDLY
IDLY(source)
200 A
Figure 1413 provides CDLY values for a wide range of time delays. The Delay pins are pulled low when
the respective input comparators noninverting input is less than the inverting input. The sink current
IDLY(sink) capability of the Delay pins is 1.8 mA and is much greater than the typical 200 A source current,
thus enabling a relatively fast delay capacitor discharge time.
The Overvoltage Drive Output is a currentlimited emitterfollower capable of sourcing 300 mA at a
turnon slew rate of 2.0 A/s, ideal for driving crowbar SCRs. The Undervoltage Indicator Output is an
opencollector NPN transistor, capable of sinking 30 mA to provide sufficient drive for LEDs, small relays
or shutdown circuitry. These current capabilities apply to both channels operating simultaneously,
providing device power dissipation limits are not exceeded. The MC3425 has an internal 2.5 V bandgap
reference regulator with an accuracy of 4.0% for the basic devices.
Figure 1412. Block Diagram

VCC
8
+
+
200A
OV Sense
Input
Comp.
OV
+
Output
Comp.
OV
+
200A
UV Sense
+
Output
Comp.
UV
Input
Comp.
UV
OV Drive
UV Indicator
2.5V
Reference
Regulator
IH
12.5A
INPUT SECTION
UV OV
DLY DLY
7
Gnd
OUTPUT SECTION
Note: All voltages and currents are nominal.
3915
Figure 1413. Output Delay Time versus Delay Capacitance
t DLY , OUTPUT DELAY TIME (ms)
100
VCC = 15 V
TA = 25C
10
1.0
0.1
2.5 CDLY
tDLY =
200 A
0.01
0.001
0.0001
0.001
0.01
0.1
1.0
CDLY, DELAY PIN CAPACITANCE (F)
10.0
E. MC34064 and MC34164 Series

The MC34064 and MC34164 series are two families of undervoltage sensing circuits specifically
designed for use as reset controllers in microprocessorbased systems. They offer the designer an
economical solution for low voltage detection with a single external resistor. Both parts feature a trimmed
bandgap reference, and a comparator with precise thresholds and builtin hysteresis to prevent erratic
reset operation.
The two families of undervoltage sensing circuits,
taken together, cover the needs of the most
Input
2
commonly specified power supplies used in
1
MCU/MPU systems. Key parameter specifications of
Reset
the MC34164 family were chosen to complement the
MC34064 series. The table summarizes critical
parameters of both families. The MC34064 fulfills the
needs of a 5.0 V 5% system and features a tighter

hysteresis specification. The MC34164 series covers
+
5.0 V 10% and 3.0 V 5% power supplies with
significantly lower power consumption, making them
1.2 Vref
ideal for applications where extended battery life
is required such as consumer products or hand
held equipment.
Gnd 3
Applications include direct monitoring of the 5.0 V
MPU/logic power supply used in appliance,

= Sink Only Positive True Logic
+
automotive, consumer, and industrial equipment.
The MC34164 is specifically designed for battery
powered applications where low bias current (1/25th
of the MC34064s) is an important characteristic.
________________________________
REFERENCES
1. Characterizing the SCR for Crowbar Applications, Al Pshaenich, Motorola AN789. (Out of Print)
2. Semiconductor Considerations for DC Power Supply SCR Crowbar Circuits, Henry Wurzburg, Third National SoldState Power Conversion
Conference, June 25, 1976.
3. Is a Crowbar Enough? Willis C. Pierce Jr., HewlettPackard, Electronic Design 20, Sept. 27, 1974.
4. Transient Thermal Response General Data and Its Use, Bill Roehr and Brice Shiner, Motorola AN569. (Out of Print)
3916
SECTION 15
HEATSINKING
A. The Thermal Equation
A necessary and primary requirement for the safe operation of any semiconductor device, whether it
be an IC or a transistor, is that its junction temperature be kept below the specified maximum value given
on its data sheet. The operating junction temperature is given by:
where:
TJ = TA + PD JA
TJ = junction temperature (C)
TA = ambient air temperature (C)
(15.1)
PD = power dissipated by device (W)

JA = thermal resistance from junctiontoambient air (C/W)
The junctiontoambient thermal resistance (JA) in Equation (15.1), can be expressed as a sum of
thermal resistances as shown below:
JA = JC + CS + SA
where: JC = junctiontocase thermal resistance
CS = casetoheatsink thermal resistance
(15.2)
SA = heatsinktoambient thermal resistance

Equation (15.2) applies only when an external heatsink is used. If no heatsink is used, JA is equal to the
device package JA given on the data sheet.
JC depends on the device and its package (case) type, while SA is a property of the heatsink and CS
depends on the type of package/heatsink interface employed. Values for JC and SA are found on the
device and heatsink data sheets, while CS is given in Table 151.
Table 151. CS For Various Packages & Mounting Arrangements
CS
MetaltoMetal*
Using an Insulator*
Case
Dry
With Heatsink
Compound
With Heatsink
Compound
Type
TO204
0.5C/W
0.1C/W
0.36C/W
0.28C/W
3 mil MICA
Anodized Aluminum
TO220
1.2C/W
1.0C/W
1.6C/W
2 mil MICA
*Typical values; heatsink surface should be free of oxidation, paint, and anodization
Examples showing the use of Equations (15.1) and (15.2) in thermal calculations are as follows:
Example 1: Find required heatsink SA for an MC7805CT, given:
TJ(max) (desired) = +125C
TA(max) = +70C
PD = 2.0 W
3917
Mounted directly to heatsink with silicon thermal grease at interface:

1. From MC7805CT data sheet, JC = 5C/W
2. From Table 151. CS = 1.6C/W
3. Using Equation (15.1) and (15.2), solve for SA:
(TJ TA)
CS JC
PD
(125 70)
SA =
5.0 1.6 ( 20.9C/W required)
2
SA =
Example 2: Find the maximum allowable TA for an unheatsinked MC78L15CT, given:

TJ(max) (desired) = +125C
PD = 0.25 W
1. From MC78L15CT data sheet, JA = 200C/W
2. Using Equation (15.1), find TA:
TA = Tj PD JA
= 125 0.25 (200)
= +75C
B. Selecting a Heatsink
Usually, the maximum ambient temperature, power being dissipated, the TJ(max), and JC for the
device being used are known. The required SA for the heatsink is then determined using Equations (15.1)
and (15.2), as in Example 1. The designer may elect to use a commercially available heatsink, or if
packaging or economy demands it, design his own.
1. Commercial Heatsinks
As an aid in selecting a heatsink, a representative listing is shown in Table 152. This listing is by no
means complete and is only included to give the designer an idea of what is available.
Table 152. Commercial Heatsink Selection Guide
TO204AA (TO3)
SA*(C/W)
Manufacturer/Series or Part Number
0.31.0
Thermalloy 6441, 6443, 6450, 6470, 6560, 6590, 6660, 6690
1.03.0
Wakefield 641
Thermalloy 6123, 6135, 6169, 6306, 6401, 6403, 6421, 6423, 6427, 6442, 6463, 6500
3.05.0
Wakefield 621, 623

Thermalloy 6606, 6129, 6141, 6303
IERC HP
Staver V332
5.07.0
Wakefield 690
Thermalloy 6002, 6003, 6004, 6005, 6052, 6053, 6054, 6176, 6301
IERC LB
Staver V352
7.010
Wakefield 672
Thermalloy 6001, 6016, 6051, 6105, 6601
IERC LA P
Staver V13, V15, V33, V35, V37
1025
Thermalloy 6013, 6014, 6015, 6103, 6104, 6105, 6117
*All values are typical as given by the manufacturer or as determined from characteristic curves supplied by the manufacturer.
3918
Table 152. Commercial Heatsink Selection Guide (continued)

TO204AA (TO5)
SA*(C/W)
12 to 20
Wakefield 260
Thermalloy 1101, 1103
Staver V3A5
20 to 30
Wakefield 209
Thermalloy 1116, 1121, 1123, 1130, 1131, 1132, 2227, 3005
IERC LP
Staver F55
30 to 50
Wakefield 207
Thermalloy 2212, 2215, 225, 2228, 2259, 2263, 2264
Staver F55, F65
Wakefield 204, 205, 208
Thermalloy 1115, 1129, 2205, 2207, 2209, 2210, 2211, 2226, 2230, 2257, 2260, 2262
Staver F15, F55
TO204AB
SA*(C/W)
5.0 to 10
IERC H P3 Series
Staver V37225, V3796
10 to 15
Thermalloy 6030, 6032, 6034

Staver V43192, V51
20 to 30
Wakefield 295
Thermalloy 6025, 6107
15 to 20
Thermalloy 6106
Staver V43128, V62
TO226AA (TO92)
SA*(C/W)
46
50
57
65
72
80 to 90
85

Staver F57A, F58
IERC AUR
Staver F57D
IERC RU
Staver F18, F27
Wakefield 292
Thermalloy 2224
DUALINLINEPACKAGE ICs
20
30
32
34
45
60
Thermalloy 6007
Thermalloy 6010
Thermalloy 6011
Thermalloy 6012
IERC LIC
Wakefield 650, 651
*All values are typical as given by the manufacturer or as determined from characteristic curves supplied by the manufacturer.
Staver Co., Inc.: 4151 N. Saxon Ave., Bay Shore, NY 11706

IERC: 135 W. Magnolia Blvd., Burbank, CA 91502
Thermalloy: P.O. Box 34829, 2021 W. Valley View Ln. Dallas, TX
Wakefield Engin Ind: Wakefield, MA 01880
3919
2. Custom Heatsink Design

Custom heatsinks are usually either forced air cooled or convection cooled. The design of forced air
cooled heatsinks is usually done empirically, since it is difficult to obtain accurate air flow measurements.
On the other hand, convection cooled heatsinks can be designed with fairly predictable characteristics. It
must be emphasized, however, that any custom heatsink design should be thoroughly tested in the actual
equipment configuration to be certain of its performance. In the following sections, a design procedure for
convection cooled heatsinks is given.
Obviously, the basic goal of any heatsink design is to produce a heatsink with an adequately low
thermal resistance, SA. Therefore, a means of determining SA is necessary in the design. Unfortunately,
a precise calculation method for SA is beyond the scope of this book.* However, a first order approximation
can be calculated for a convection cooled heatsink if the following conditions are met:
1.
2.
3.
4.
The heatsink is a flat rectangular or circular plate whose thickness is smaller than its length or width.
The heatsink will not be located near other heat radiating surfaces.
The aspect ratio of a rectangular heatsink (length:width) is not greater than 2:1.
Unrestricted convective air flow.
For the above conditions, the heatsink thermal resistance can be approximated by:
SA
where:
] A (Fchc1 + Hr)
(C/W)
(15.3)
A = area of the heatsink surface

= heatsink effectiveness
Fc = convective correction factor
hc = convection heat transfer coefficient
= emissivity
Hr = normalized radiation heat transfer coefficient

The convective heat transfer coefficient, hc, can be found from Figure 151. Note that it is a function
of the heatsink fin temperature rise (TS TA) and the heatsink significant dimension (L). The fin temperature
rise (TS TA) is given by:
TS TA = SA PD
(15.4)
where: TS = heatsink temperature
TA = ambient temperature
SA = heatsinktoambient thermal resistance
PD = power dissipated
hc , CONVECTION COEFFICIENT
(W/In 2 C) x 10 3
Figure 151. Convection Coefficient (hc)

10
9.0
8.0
7.0
6.0
L = 1
5.0
4.0
*If greater precision is desired, or

more information on heat flow and
heatsinking is sought, consult the
references list at the end of this
section.
10
3.0
2.0
10
3920
20
30
50
70
100
TS TA, FIN TEMPERATURE RISE OF PLATE (C)
200
The significant heatsink dimension (L) is dependent on the heatsink shape and mounting place and
is given in Table 153. The convective correction factor (Fc) is likewise dependent on shape and mounting
plane of the heatsink and is also given in Table 153.
Table 153. Significant Dimension (L) and Correction Factor (Fc)
for Convection Thermal Resistance
Significant Dimension L
Surface
Position
Vertical
Correction Factor Fc
Position
Fc
Height (max 2 ft)
Vertical Plane
1.0
Horizontal
length width
length + width
Horizontal Plane
both surfaces
exposed
1.35
Vertical
/ 1 diameter
Top only exposed
0.9
Rectangular Plane
Circular Plane
The normalized radiation heat transfer coefficient (Hr) is dependent on the ambient temperature (TA) and
the heatsink temperature rise (TS TA) given by Equation (15.4). Hr can be determined from Figure 152.
H r , NORMALIZED RADIATION COEFFICIENT

(W/In 2 C) x 10 2
Figure 152. Normalized Radiation Coefficient (Hr)

2.0
1.5
1.0
0.9
0.8
0.7
TA = 100C
75C
50C
0.6
0.5
25C
0.4
10
20
30
50
70
100
TS TA, TEMPERATURE RISE OF PLATE (C)
200
The emissivity () can be found in Table 154 for various heatsink surfaces.
Table 154. Typical Emissivities of Common Surfaces
Surface
Alodine on Aluminum
Aluminum, Anodized
Aluminum, Polished
Copper, Polished
Copper, Oxidized
Rolled Sheet Steel
Air Drying Enamel (any color)
Oil Paints (any color)
Varnish
Emissivity ()
0.15
0.7 to 0.9
0.05
0.07
0.70
0.66
0.85 to 0.91
0.92 to 0.96
0.89 to 0.93
3921
Finally, the heatsink efficient () can be found from the nomograph of Figure 153. Use of the
nomograph is as follows:
a) Find hT = Fchc + Hr from Figures 151, 152 and Tables 153 and 154,
and locate this point on the nomograph.
b) Draw a line from hT through chosen heatsink fin thickness (x) to find .
c) Determine D for the heatsink shape as given in Figure 154 and draw a line
from this point through , which was found in (b), to determine .
d) If power dissipating element is not located at heatsinks center of symmetry,
multiply by 0.7 (for vertically mounted plates only).
Note that in order to calculate SA from Equation (15.3), it is necessary to know the heatsink size.
Therefore, in order to arrive at a suitable heatsink design, a trial size is selected, its SA evaluated, and the
original size reduced or enlarged as necessary. This process is iterated until the smallest heatsink is
obtained that has the required SA. The following design example is given to illustrate this procedure.
Figure 153. Fin Effectiveness Nomogram for Symmetrical Flat, Uniformly Thick Fins
D
4.0
0.05
3.0
Fin Thickness
For
Aluminum
0.1
2.0
For
Copper
hT = FChC+Hr
10
Fin Effectiveness
0.2
0.8
0.7
0.6
0.5
10
10
0.3
0.4
0.5
1.0
1.0
1.0
0.1
0.1
1.0
2.0
0.2
88
0.1
85
0.001
0.001
3.0
4.0
5.0
0.3
94
90
0.01
0.01
0.4
1.0
0.0001
84
80
82
0.01
75
Inches
70
65
10.0
Inches
60
0.001
55
W/In2/C
50
45
40
35
%
Figure 154. Determination of D for Use in Nomograph of Figure 153
3922
^ ab , if a,b S & b 2a
] d2 , if ds
Heatsink Design Example

Design a flat rectangular heatsink for use with a horizontally mounted power device on a PC board,
given the following:
1. Heatsink SA = 25C/W
2. Power to be dissipated, PD = 2.0 W
3. Maximum ambient temperature, TA = 50C
4. Heatsink to be constructed from 1/8 (0.125) thick anodized aluminum.
a) First, a trial heatsink is chosen: 2 3 (experience will simplify this selection and
reduce the number of necessary iterations.)
b) The factors in Equation (15.3) are evaluated by using the Figures and Tables given:
A = 2 3 = 6 sq. in.
L = 6/5 = 1.2 in. (from Table 153)
TS TA = 50C (from Figure 154)
hc = 5.8 103 W/in2 C (from Figure 151)
Fc = 0.9 (from Table 153)
Hr = 6.1 103 W/in2 C (from Figure 152)
= 0.9 (from Table 154)
hT = Fchc + Hr = 10.7 103 W/in2 C
= 0.13 (from Figure 153)
D = 1.77 (from Figure 154)
> 0.94
]1 (from Figure 153)
c) Using Equation (15.3), find SA:

SA
] A (Fchc1 + Hr) = 16.66C/W < 25C/W
d) Since 2 3 is too large, try 2 2. Following the same procedure, SA is found

to be 25C/W, which exactly meets the design requirements.
SOIC MINIATURE IC PLASTIC PACKAGE

Thermal Information
The maximum power consumption an integrated circuit can tolerate at a given operating ambient
temperature, can be found from the equation:
TJ(max) TA
PD(T =
A)
RJA (typ)
where: PD(TA) = power dissipation allowable at a given operating ambient temperature,
TJ(max) = maximum operating junction temperature as listed in the maximum ratings section,
TA = desired operating ambient temperature,
RJA (typ) = typical thermal resistance junctiontoambient.
Maximum Ratings
Rating
Symbol
Value
Unit
Operating Ambient Temperature Range
TA
0 to +70
40 to +85
Operating Junction Temperature
TJ
150
Tstg
55 to +150
Storage Temperature Range
3923
THERMAL CHARACTERISTICS OF SOIC PACKAGES

Measurement specimens are solder mounted on a Philips SO test board #7322078, 80873 in still air.
No auxiliary thermal conduction aids are used. As thermal resistance varies inversely with die area, a given
package takes thermal resistance values between the max and min curves shown. These curves represent
the smallest (2000 square mils) and largest (8000 square mils) die areas expected to be assembled in the
SOIC package.
Figure 155. Thermal Resistance,
JunctiontoAmbient (C/W)
Figure 156. SOP8 Thermal Resistance and Maximum

Power Dissipation versus P.C.B. Copper Length
_
170
160
_
Min. Die Size
2K Mils2
140 _
120
Max. Die Size

See Figure 156
8K Mils2
for Heatsink
Detail
|
|
|
|
SO8
SOP8*
SO14
SO16
PACKAGE STYLE
100 _
3.2
150
C/W
JA
180
PD(max) for TA = +50C
130
2.4
110
Graph represents symmetrical layout
90
2.0
1.6
2.0 oz.
Copper
70
1.2
L
3.0 mm
50
0.8
RJA
30
0
Data taken using Philips SO test board #7322078, 80873

*SOP8 using standard SO8 footprint minimum pad size
2.8
10
20
30
40
0.4
50
200
SOP8 and SOP16L Packaged Devices

Several families of voltage regulators and power control ICs have been
introduced in surface mounted packages which were developed by the
Analog IC Division. The SOP8 and SOP16L packages have external
dimensions which are identical to the standard SO8 and SO16L surface
mount devices, but the center four leads of the packages are all connected
to the leadframe die flag. This internal modification decreases the package
thermal resistance and therefore increases its power dissipation capability.
This advantage is fully realized when the package is mounted on a printed
circuit board with a single pad for the four center leads. This large area of
copper then acts as an external heat spreader, efficiently conducting heat
away from the package.
Figure 157. SOP16L Thermal Resistance and Maximum
2.8
90
80
2.4
Graph represents symmetrical layout
70
L
60
2.0 oz.
Copper
L
50
3.0 mm
RJA
40
10
1.6
1.2
0.8
0.4
30
0
2.0
20
30
40
0
50
100
3924
THERMAL CHARACTERISTICS OF DPAK AND D2PAK PACKAGE

The evaluation was performed using an active device (4900 square mils) mounted on 2.0 ounce copper
foil epoxied to a GIO type printed circuit board. Measurements were made in still air and no auxiliary
thermal conduction aids were used. The size of a square copper pad was varied, and all measurements
were made with the unit mounted as shown in Figure 158. The curve shown in Figure 158 is a plot of
junctiontoair thermal resistance versus the length of the square copper pad in millimeters. This shows
that when the DPAK is mounted on a 10 mm 10 mm square pad of 2.0 ounce copper it has a thermal
resistance which is comparable to a TO220 device mounted vertically without additional heatsinking.
100
2.4
Free Air
Mounted
Vertically
90
2.0
80
Minimum
Size Pad
70
60
2.0 oz. Copper

L
1.6
1.2
50
0.8
0.4
RJA
40
0
0
5.0
10
15
20
25
Figure 158. DPAK Thermal Resistance and Maximum

30
The thermal characteristics of the D2PAK are shown in Figure 159. The device was mounted on
2.0 oz. copper on an FR4type P.C. board. The maximum power dissipation was measured with a junction
temperature of 150C.
80
3.5

70
3.0
Free Air
Mounted
Vertically
60
2.0 oz. Copper

L
Minimum
Size Pad
50
2.5
2.0
40
1.5
RJA
30
1.0
0
5.0
10
15
20
25
Figure 159. 3Pin and 5Pin D2PAK

Thermal Resistance and Maximum Power
Dissipation versus P.C.B. Copper Length
30
3925

Voltage Reg Apps

Uploaded by

Copyright:

Available Formats

Voltage Reg Apps

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Voltage Reg Apps

Uploaded by

Copyright:

Available Formats

Linear & Switching Voltage Regulator

MOTOROLA ANALOG IC DEVICE DATA

Basic Linear Regulator Theory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Selecting a Linear IC Voltage Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Linear Regulator Circuit Configuration and Design Considerations . . . . . . . . . . . . . . . . . . . . . . .

Series Pass Element Considerations for Linear Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Linear Regulator Construction and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Linear Regulator Design Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Linear Regulator Circuit Troubleshooting Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MOTOROLA ANALOG IC DEVICE DATA

TABLE OF CONTENTS (Continued)

Designing the Input Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

An Introduction to Switching Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Switching Regulator Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Switching Regulator Component Design Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Basic Switching Power Supply Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Switching Regulator Design Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power Supply Supervisory and Protection Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MOTOROLA ANALOG IC DEVICE DATA

1. Zener Diode Reference

where: VBZ = zener breakdown voltage

MOTOROLA ANALOG IC DEVICE DATA

Figure 11. Voltage Regulator Functional Block Diagram

Figure 12. Voltage Regulator Equivalent Circuit Model

Figure 13. Zener Diode Reference

MOTOROLA ANALOG IC DEVICE DATA

2. Constant Current Zener Reference

where: VBEQ1 = baseemitter voltage of Q1.

where IZ is constant and given by Equation 2.

Figure 14. Constant Current (Zener Reference)

MOTOROLA ANALOG IC DEVICE DATA

(neglecting base currents)

The change in Vref with junction temperature is given by:

It can be shown that,

and, VBEQ2 = TJK ln I2

Combining (5), (6), and (7)

MOTOROLA ANALOG IC DEVICE DATA

C. The Error Amplifier

AVOL = amplifier open loop gain

i= true differential input voltage

1. Amplifier Input Offset Voltage Drift

2. Amplifier Power Supply Sensitivity

MOTOROLA ANALOG IC DEVICE DATA

Figure 16. Typical Voltage Regulator Configuration

V1 = voltage on amplifier noninverting input

Figure 17. Definition of Common Mode Voltage Error

MOTOROLA ANALOG IC DEVICE DATA

Figure 18. Common Mode Regulator Effects

CMRR = common mode rejection ratio

MOTOROLA ANALOG IC DEVICE DATA

3. Amplifier Output Impedance

D. The Regulator within a Regulator Approach

MOTOROLA ANALOG IC DEVICE DATA

Constant currentzener method

High CMRR amplifier

Low VIO drift amplifier

Low ZOL amplifier

As shown in Figure 110, amplifier A1 sets up a voltage (V1) given by:

MOTOROLA ANALOG IC DEVICE DATA