Seminar report

On
Pollution

Submitted in the partial fulfillment for the requirement of the Degree of

Master of Business Administration (Integrated course)
(2015-2016)

Submitted to
Punjabi University, Patiala

Supervisor

Submitted By
Dr. Harpreet Singh

Baljeet Kaur
MBA[IC] 1st
Roll no. 903

ACKNOWLEDGEMENT
Written words have the tendency to degenerate genuine gratitude into stilted
formality but this is the only way to express my feelings. I am indebted to all those who
supported me in this learning process and in successful completion of my Seminar
Report. I wish to express my seminar report predication to all those with whom in
interacted and whose thought and insight helped me in increasing my knowledge and
understanding the seminar report.
I also owe my thanks to my teacher Dr. Harpreet Singh for their kind guidance
and unstinted support throughout the training and even before.

Baljeet Kaur

DECLARATION
I Baljeet Kaur here by declared that the work which is being presented in the
project report Pollution is the Original Work by me under the supervision of Dr.
Harpreet Singh (Assistant Professor) for fulfillment of the award of degree Master of
-Business administration (integrated course) to the University School Of Business
Studies, Guru Kashi Campus, Talwandi Sabo (Bathinda).

-----------------------------Signature

INDEX

1. Introduction
2. Definiation
3. Major forms of pollution

Air pollution

Water pollution

Soil pollution

Noise pollution

Visual pollution

Thermal pollution

4. Effects of pollution
5. Sources and Causes
6. Pollution preventions
7.

Conclusion

INTRODUCTION

Amongst the developing countries, India is the foremost nation to take note of
degradation of environment .
In 1972, in the world environmental conference held at
Stockholm, our government declared that it is their responsibility to control pollution in
India. Even during recent global conference held at kyoto in Japan, India accepted the
responsibility of reducing global warming and depletion of ozone layer by banning the
use of chloro-fluoro carbons in cryogenic engineering within a stipulated period. Even in
the recent conference held in Rio-de-Janeiro, India declared solidarity by conforming to
the standards as stipulated by United States Environmental Protection Agencies (USEPA). Perhaps India was the foremost country in third worlds to implement rigorously
pollution legislation both for air and water. We accepted the stipulated levels of the
pollutants in act designated as maximum permissible level to be implemented in
successive stages in few years. Within India, Maharashtra state was the front runner to
enact Water Pollution and Control Act in 1962. This was followed by passing of
Comprehensive Environmental Protection Bill for prevention of air pollution in 1983.
Maharashtra, Gujarat, Madhya Pradesh were the first states in Indian union to
have pollution control board with attached analytical laboratories. This was followed by
the setting of series of laboratories in all remaining states of the nation. A legislation was
passed. The grave tragedy of Bhopal in 1984 by accidentally releasing deadly poisonous
gas such as methyl isocyanate took a toll of more than 4500 people who were innocent
and helpless. With the growing civilisation and with rise in traffic, auto-exhaust emission
also takes a toll of people. Therefore government enacted PUC act to check every
vehicle periodically and control, release of hazardous gases like NO-NOx, CO, and
hydrocarbons in air. As a matter of fact, India did much more than any other developing
country could do to control pollution. Even in controlling global warming and reduction
of the Green House gases we were certainly ahead of developed countries like Canada,
USA, Australia. General incentives were given by our government to design and develop
indigenously pollution monitoring instruments within the country and make us selfsufficient. At moment, separate ministry looks after all problems related to pollution. In

fact, all nations have their own ministry or department to implement effectively
legislation related to
control of pollution.

Definition

Defining air pollution is not simple. One could claim that air pollution started when
humans began burning fuels. In other words, all man-made (anthropogenic) emissions
into the air can be called air pollution, because they alter the chemical composition of the
natural atmosphere. The increase in the global concentrations of greenhouse gases CO2,
CH4 can be called air pollution using this approach, even though the concentrations have
not found to be toxic for humans and the ecosystem. One can refine this approach and
only consider anthropogenic emissions of harmful chemicals as air pollution. However,
this refined approach has some drawbacks. Firstly, one has to define what harmful
means. Harmful could mean an adverse effect on the health of living things, an adverse
effect on anthropogenic or natural non-living structures, or a reduction in the airs
visibility. Also, a chemical that does not cause any short-term harmful effects may
accumulate in the atmosphere and create a long-term harmful effect.
Pollution is the introduction of contaminants into the natural
environment that cause adverse change. Pollution can take the form of chemical
substances or energy, such as noise, heat or light. Pollutants, the components of pollution,
can be either foreign substances/energies or naturally occurring contaminants. Pollution is
often classed as point source or nonpoint source pollution. The Blacksmith Institute
issues an annual list of the world's worst polluted places. In the 2007 issues the ten top
nominees are located in Azerbaijan, China, India, Peru, Russia, Ukraine and Zambia
The contamination of air, water, or soil by substances that are harmful
to living organisms. Pollution can occur naturally, for example through volcanic
eruptions, or as the result of human activities, such as the spilling of oil or disposal of
industrial waste. Light from cities and towns at night that interferes with astronomical
observations is known as light pollution. It can also disturb natural rhythms of growth in

plants and other organisms. Continuous noise that is loud enough to be annoying or
physically harmful is known as noise pollution. Heat from hot water that is discharged
from a factory into a river or lake, where it can kill or endanger aquatic life, is known as
thermal pollution.

Major forms of pollution

There are several kinds of pollution:
8. Air Pollution
9. Water Pollution
10. Soil Pollution
11. Noise Pollution
12. Visual Pollution
13. Thermal Pollution
The major forms of pollution are listed below along with the particular pollutants
relevant to each of them:
Air pollution, the release of chemicals and particulates into the atmosphere.
Common air pollutants include carbon monoxide, sulfur
dioxide, chlorofluorocarbons (CFCs) and nitrogen oxides produced by industry and
motor vehicles. Photochemical ozone and smog are created as nitrogen oxides and
hydrocarbons react to sunlight.
Water pollution, by the release of waste products and contaminants into surface
runoff into river drainage systems, leaching into groundwater, liquid spills, wastewater
discharges, eutrophication and littering.
Soil contamination occurs when chemicals are released by spill or underground
leakage. Among the most significant soil contaminants are hydrocarbons, heavy metals,
herbicides, pesticides and chlorinated hydrocarbons.

 Radioactive contamination, resulting from 20th century activities in atomic

physics, such as nuclear power generation and nuclear weapons research, manufacture
and deployment.
Noise pollution, which encompasses roadway noise, aircraft noise, industrial noise
as well as high-intensity sonar.
Light pollution, includes light trespass, over-illumination and astronomical
interference.
Visual pollution, which can refer to the presence of overhead power lines,
motorway billboards, scarred landforms (as from strip mining), open storage of trash or
municipal solid waste.
Thermal pollution, is a temperature change in natural water bodies caused by
human influence, such as use of water as coolant in a power plant.

Air pollution
Air pollution is the introduction of chemicals, particulate matter, or biological materials
that cause harm or discomfort to humans or other living organisms, or cause damage to
the natural environment or built environment, into the atmosphere.

The atmosphere is a complex dynamic natural gaseous system that is essential to support
life on planet Earth. Stratospheric ozone depletion due to air pollution has long been
recognized as a threat to human health as well as to the Earth's ecosystems.
Indoor air pollution and urban air quality are listed as two of the world's worst pollution
problems in the 2008 Blacksmith Institute World's Worst Polluted Places report.

Causes and effects of air pollution:

(1) Greenhouse effect,
(2) Particulate contamination,
(3) Increased UV radiation,
(4) Acid rain,
(5) Increased ground level ozone concentration,
(6) Increased levels of nitrogen oxides.
A substance in the air that can cause harm to humans and the environment is known as an
air pollutant. Pollutants can be in the form of solid particles, liquid droplets, or gases. In
addition, they may be natural or man-made.
Pollutants can be classified as primary or secondary. Usually, primary pollutants are
directly emitted from a process, such as ash from a volcanic eruption, the carbon
monoxide gas from a motor vehicle exhaust or sulfur dioxide released from factories.
Secondary pollutants are not emitted directly. Rather, they form in the air when primary
pollutants react or interact. An important example of a secondary pollutant is ground level
ozone one of the many secondary pollutants that make up photochemical smog. Some
pollutants may be both primary and secondary: that is, they are both emitted directly and
formed from other primary pollutants.

Major primary pollutants produced by human activity include:

Sulphur oxides (SOx) - especially sulfur dioxide, a chemical compound with the
formula SO2. SO2 is produced

by volcanoes and in various industrial processes. Since

coal

and petroleum often contain sulpher compounds, their combustion generates

sulfur dioxide. Further oxidation of SO2, usually in the presence of a catalyst such as
NO2, forms H2SO4, and thus acid rain. This is one of the causes for concern over the
environmental impact of the use of these fuels as power sources.

Nitrogen oxides (NOx) - especially nitrogen dioxide are emitted from high
temperature combustion, and are also produced naturally during thunderstorms by
electrical discharge. Can be seen as the brown haze dome above or plume
downwind of cities. Nitrogen dioxide is the chemical compound with the formula
NO2. It is one of the several nitrogen oxides. This reddish-brown toxic gas has a
characteristic sharp, biting odor. NO2 is one of the most prominent air pollutants.

Carbon monoxide (CO) It is a colourless, odorless, non-irritating but very

poisonous gas. It is a product by incomplete combustion of fuel such as natural
gas, coal or wood. Vehicular exhaust is a major source of carbon monoxide.

Carbon dioxide (CO2)

a colourless, odorless, non-toxic greenhouse gas also

associated with ocean acidification, emitted from sources such as combustion,

cement production, and respiration. It is otherwise recycled in the atmosphere in
the carbon cycle.

Volatile organic compounds - VOCs are an important outdoor air pollutant.

In this field they are often divided into the separate categories of methane (CH4)
and non-methane (NMVOCs). Methane is an extremely efficient greenhouse gas
which contributes to enhanced global warming. Other hydrocarbon VOCs are also
significant greenhouse gases via their role in creating ozone and in prolonging the
life of methane in the atmosphere, although the effect varies depending on local
air quality. Within the NMVOCs, the aromatic compounds benzene, toluene and
xylene are suspected carcinogens and may lead to leukemia through prolonged
exposure. 1,3-butadiene is another dangerous compound which is often associated
with industrial uses.

Particulate matter - Particulates, alternatively referred to as particulate

matter (PM) or fine particles, are tiny particles of solid or liquid suspended in a
gas. In contrast, aerosol refers to particles and the gas together. Sources of
particulate matter can be man made or natural. Some particulates occur naturally,
originating from volcanoes, dust storms, forest and grassland fires, living
vegetation, and sea spray. Human activities, such as the burning of fossil fuels in
vehicles, power plants and various industrial processes also generate significant
amounts of aerosols. Averaged over the globe, anthropogenic aerosolsthose
made by human activitiescurrently account for about 10 percent of the total
amount of aerosols in our atmosphere. Increased levels of fine particles in the air
are linked to health hazards such as heart disease, altered lung function and lung
cancer.

Persistent free radicals connected to airborne fine particles could cause

cardiopulmonary disease.

Toxic metals, such as lead, cadmium and copper Chlorofluorocarbons (CFCs) harmful to the ozone layer emitted from products currently banned from use.

Ammonia (NH3) - emitted from agricultural processes. Ammonia is a

compound with the formula NH3. It is normally encountered as a gas with a
characteristic pungent odor. Ammonia contributes significantly to the nutritional
needs of terrestrial organisms by serving as a precursor to foodstuffs and
fertilizers. Ammonia, either directly or indirectly, is also a building block for the
synthesis of many pharmaceuticals. Although in wide use, ammonia is both
caustic and hazardous.

Secondary pollutants include:

Particulate matter formed from gaseous primary pollutants and compounds in

photochemical smog. Smog is a kind of air pollution; the word "smog" is a
portmanteau of smoke and fog. Classic smog results from large amounts of coal
burning in an area caused by a mixture of smoke and sulfur dioxide. Modern
smog does not usually come from coal but from vehicular and industrial
emissions that are acted on in the atmosphere by ultraviolet light from the sun to
form secondary pollutants that also combine with the primary emissions to form
photochemical smog.

Ground level ozone (O3) formed from NOx and VOCs. Ozone (O3) is a key
constituent of the troposphere. It is also an important constituent of certain
regions of the stratosphere commonly known as the Ozone layer. Photochemical
and chemical reactions involving it drive many of the chemical processes that
occur in the atmosphere by day and by night. At abnormally high concentrations
brought about by human activities (largely the combustion of fossil fuel), it is a
pollutant, and a constituent of smog.

Peroxyacetyl nitrate (PAN) - similarly formed from NOx and VOCs.

Minor air pollutants include:

A large number of minor hazardous air pollutants. Some of these are regulated in
USA under the Clean Air Act and in Europe under the Air Framework Directive.

A variety of persistent organic pollutants, which can attach to particulate matter.

Persistent organic pollutants (POPs) are organic compounds that are resistant to
environmental degradation through chemical, biological, and photolytic processes.
Because of this, they have been observed to persist in the environment, to be capable of
long-range transport, bioaccumulate in human and animal tissue, biomagnify in food
chains, and to have potential significant impacts on human health and the environment.

Effects of Pollution In Atmosphere

Health effects
Air pollution is a significant risk factor for multiple health conditions including
respiratory infections, heart disease, and lung cancer, according to the WHO. The health
effects caused by air pollution may include difficulty in breathing, wheezing, coughing
and aggravation of existing respiratory and cardiac conditions. These effects can result in
increased medication use, increased doctor or emergency room visits, more hospital
admissions and premature death. The human health effects of poor air quality are far
reaching, but principally affect the body's respiratory system and the cardiovascular
system. Individual reactions to air pollutants depend on the type of pollutant a person is
exposed to, the degree of exposure, the individual's health status and genetics.
The most common sources of air pollution include particulate matter, ozone, nitrogen
dioxide, and sulfur dioxide. Both indoor and outdoor air pollution have caused
approximately 3.3 million deaths worldwide. Children aged less than five years that live
in developing countries are the most vulnerable population in terms of total deaths
attributable to indoor and outdoor air pollution.
The World Health Organization states that 2.4 million people die each year from causes
directly attributable to air pollution, with 1.5 million of these deaths attributable to indoor
air pollution "Epidemiological studies suggest that more than 500,000 Americans die
each year from cardiopulmonary disease linked to breathing fine particle air pollution. . ."
A study by the University of Birmingham has shown a strong correlation between
pneumonia related deaths and air pollution from motor vehicles. Worldwide more deaths
per year are linked to air pollution than to automobile accidents. A 2005 study by the
European Commission calculated that air pollution reduces life expectancy by an average
of almost nine months across the European Union. Causes of deaths include aggravated
asthma, emphysema, lung and heart diseases, and respiratory allergiesThe US EPA
estimates that a proposed set of changes in diesel engine technology could result in
12,000 fewer premature mortalities, 15,000 fewer heart attacks, 6,000 fewer emergency
room visits by children with asthma, and 8,900 fewer respiratory-related hospital
admissions each year in the United States.

The US EPA estimates allowing a ground-level ozone concentration of 65 parts per

billion, would avert 1,700 to 5,100 premature deaths nationwide in 2020 compared with
the current 75-ppb standard. The agency projects the stricter standard would also prevent
an additional 26,000 cases of aggravated asthma, and more than a million cases of missed
work or school.
The worst short term civilian pollution crisis in India was the 1984 Bhopal Disaster.
Leaked industrial vapours from the Union Carbide factory, belonging to Union Carbide,
Inc., U.S.A., killed more than 25,000 people outright and injured anywhere from 150,000
to 600,000. The United Kingdom suffered its worst air pollution event when the
December 4 Great Smog of 1952 formed over London. In six days more than 4,000 died,
and 8,000 more died within the following months. An accidental leak of anthrax spores
from a biological warfare laboratory in the former USSR in 1979 near Sverdlovsk is
believed to have been the cause of hundreds of civilian deaths. The worst single incident
of air pollution to occur in the United States of America occurred in Donora,
Pennsylvania in late October, 1948, when 20 people died and over 7,000 were injured.
A new economic study of the health impacts and associated costs of air pollution in the
Los Angeles Basin and San Joaquin Valley of Southern California shows that more than
3800 people die prematurely (approximately 14 years earlier than normal) each year
because air pollution levels violate federal standards. The number of annual premature
deaths is considerably higher than the fatalities related to auto collisions in the same area,
which average fewer than 2,000 per year.
Diesel exhaust (DE) is a major contributor to combustion derived particulate matter air
pollution. In several human experimental studies, using a well validated exposure
chamber setup, DE has been linked to acute vascular dysfunction and increased thrombus
formation. This serves as a plausible mechanistic link between the previously described
association between particulate matter air pollution and increased cardiovascular
morbidity and mortality.

Possible links to cancer

A large Danish epidemiological study found an increased risk of lung cancer for patients
who lived in areas with high nitrogen oxide concentrations. In this study, the association
was higher for non-smokers than smokers. There are also possible associations between
air pollution and other forms of cancer, including cervical cancer and brain cancer.

Effects on children
Cities around the world with high exposure to air pollutants have the possibility of
children living within them to develop asthma, pneumonia and other lower respiratory
infections as well as a low initial birth rate. Protective measures to ensure the youths'
health are being taken in cities such as New Delhi, India where buses now use
compressed natural gas to help eliminate the "pea-soup" smog. Research by the World
Health Organization shows there is the greatest concentration of particulate matter
particles in countries with low economic world power and high poverty and population
rates. Examples of these countries include Egypt, Sudan, Mongolia, and Indonesia. In the
United States, the Clean Air Act was passed in 1970; however, in 2002 at least 146
million Americans were living in non-attainment areasregions in which the
concentration of certain air pollutants exceeded federal standards. Those pollutants are
known as the criteria pollutants, and include ozone, particulate matter, sulfur dioxide,
nitrogen dioxide, carbon monoxide, and lead. Because children are outdoors more and
have higher minute ventilation they are more susceptible to the dangers of air pollution.

Health effects in relatively "clean" areas

Even in the areas with relatively low levels of air pollution, public health effects can be
significant and costly, since a large number of people breathe in such pollutants. A
2005 scientific study for the British Columbia Lung Association showed that a
small improvement in air quality (1% reduction of ambient PM2.5 and ozone
concentrations) would produce a $29 million in annual savings in the Metro
Vancouver region in 2010. This finding is based on health valuation of lethal
(death) and sub-lethal (illness) effects.

Reduction efforts
There are various air pollution control technologies and land use planning strategies
available to reduce air pollution. At its most basic level land use planning is likely
to involve zoning and transport infrastructure planning. In most developed
countries, land use planning is an important part of social policy, ensuring that land
is used efficiently for the benefit of the wider economy and population as well as to
protect the environment.Efforts to reduce pollution from mobile sources includes
primary regulation (many developing countries have permissive regulations),
expanding regulation to new sources (such as cruise and transport ships, farm
equipment, and small gas-powered equipment such as lawn trimmers, chainsaws,
and snowmobiles), increased fuel efficiency (such as through the use of hybrid
vehicles), conversion to cleaner fuels (such as bioethanol, biodiesel, or conversion
to electric vehicles).

Control devices
The following items are commonly used as pollution control devices by industry or
transportation devices. They can either destroy contaminants or remove them from an
exhaust stream before it is emitted into the atmosphere.

Particulate control
o

Mechanical collectors (dust cyclones, multicyclones)

Electrostatic precipitators An electrostatic precipitator (ESP), or

electrostatic air cleaner is a particulate collection device that removes
particles from a flowing gas (such as air) using the force of an induced
electrostatic charge. Electrostatic precipitators are highly efficient
filtration devices that minimally impede the flow of gases through the
device, and can easily remove fine particulate matter such as dust and
smoke from the air stream.

Baghouses Designed to handle heavy dust loads, a dust collector consists

of a blower, dust filter, a filter-cleaning system, and a dust receptacle or

dust removal system (distinguished from air cleaners which utilize

disposable filters to remove the dust).

Particulate scrubbersWet scrubber is a form of pollution control

technology. The term describes a variety of devices that use pollutants
from a furnace flue gas or from other gas streams. In a wet scrubber, the
polluted gas stream is brought into contact with the scrubbing liquid, by
spraying it with the liquid, by forcing it through a pool of liquid, or by
some other contact method, so as to remove the pollutants.

Atmospheric dispersion
The basic technology for analyzing air pollution is through the use of a variety of
mathematical models for predicting the transport of air pollutants in the lower
atmosphere. The principal methodologies are:

Point source dispersion, used for industrial sources.

Line source dispersion, used for airport and roadway air dispersion modeling

Area source dispersion, used for forest fires or duststorms

Photochemical models, used to analyze reactive pollutants that form smog

The point source problem is the best understood, since it involves simpler mathematics
and has been studied for a long period of time, dating back to about the year 1900. It uses
a Gaussian dispersion model for buoyant pollution plumes to forecast the air pollution
isopleths, with consideration given to wind velocity, stack height, emission rate and
stability class (a measure of atmospheric turbulence). This model has been extensively
validated and calibrated with experimental data for all sorts of atmospheric conditions.
The roadway air dispersion model was developed starting in the late 1950s and early
1960s in response to requirements of the National Environmental Policy Act and the U.S.
Department of Transportation (then known as the Federal Highway Administration) to

understand impacts of proposed new highways upon air quality, especially in urban areas.
Several research groups were active in this model development, among which were: the
Environmental Research and Technology (ERT) group in Lexington, Massachusetts, the
ESL Inc. group in Sunnyvale and California, California Air Resources Board group in
Sacramento, California. The research of the ESL group received a boost with a contract
award from the United States Environmental Protection Agency to validate a line source
model using sulfur hexafluoride as a tracer gas. This program was successful in
validating the line source model developed by ESL inc. Some of the earliest uses of the
model were in court cases involving highway air pollution, the Arlington, Virginia
portion of Interstate 66 and the New Jersey Turnpike widening project through East
Brunswick, New Jersey.
Area source models were developed in 1971 through 1974 by the ERT and ESL groups,
but addressed a smaller fraction of total air pollution emissions, so that their use and need
was not as widespread as the line source model, which enjoyed hundreds of different
applications as early as the 1970s. Similarly photochemical models were developed
primarily in the 1960s and 1970s, but their use was more specialized and for regional
needs, such as understanding smog formation in Los Angeles, California.

Industry and farming

However, pharmaceuticals are not the largest contributor to the growing amount of
gender-altering pollution in the water. Scientists at the University of California San
Francisco (UCSF) stated that there are many other sources of chemicals like the ones
found in various pharmaceuticals that produce the same effects. Crop fertilizers along
with dairy cows, and various industrial chemicals like BPA are increasingly seen as a
source for pollution causing certain specific effects in those who consume them or
products that are manufactured from them. Specifically shifting to industrial chemicals,
when they, along with other products containing these chemicals, are disposed of, they
end up in landfills. Runoff from said landfills eventually finds its way to a larger source
of water and the contamination begins.

Water cycle
A second source of circulation is water as it follows its natural path through the water
cycle. The water cycle, put simply, represents the path that water takes as it circulates
around planet earth. It follows a series of stages in which the water changes state multiple
times until it finally falls back to earth where it will once again be circulated. In the water
cycle, both organic and inorganic pollutants are biodegraded or filtered out whereas they
no longer present much of a threat. This is also true for small amounts of chemicals
present in the water. However, when there are very large amounts of chemicals, organic
or inorganic, present in the water as it cycles through the atmosphere, harmful effects can
be seen in areas where this water falls as precipitation. This precipitation re-enters the
ongoing circulation of water pollution.

Ocean and marine life

Another path in which the water can circulate is by flowing directly to the ocean.
Pollutants are prevalent in coastal and open-ocean waters as contaminated water flows
from point sources to the sea. These pollutants are then distributed globally due to the
circulation of the ocean currents and migration of exposed marine life. This becomes an
explanation of how the chemicals, once again, find their way to a human consumer.
Marine wildlife in a polluted area exists in and consumes contaminated water daily.
When it is harvested, it has accumulated an amount of harmful chemicals/EDCs
relatively high to that compared to ambient ocean levels. This is then passed on to
consumers of the seafood: humans, whereas the chemicals bioaccumulate in their bodies
eventually causing sex-related health problems

Effects of pollutants on sex

These chemicals have an effect on the sex of many humans because of constant exposure.
The pollutants found in the water have been observed in many studies that produce
concrete data describing the effects they have on the hormones in both males and
females. Studies have been conducted on animals, but the observed trends are also
associated with effects noticed in humans. Scientists observing EDCs in womens blood
found that these chemicals mimic human hormones and trigger changes in the sexdetermining process of unborn children. Some scientists suggest that this hormonal
influence on the sex-determining process has led to a decrease in the male/female ratio.
Other effects directly influencing the sex of an individual include a decrease in number
and quality of sperm and increased deficiency in a males reproductive system.
Specifically looking at the effects of EDCs on sperm, these chemicals cause a premature
release of a chemical that the sperm cells use to penetrate the eggs outer layer. Results
collected from a study help to explain why the sperm act the way they do. In respect to
the deficiency of the males reproductive system, these chemicals begin affecting a male
as early as birth. As the testes are developing, an occurrence taking place early in the
development process, a specific type of cells, Sertoli cells, differentiates. During this
period, exposure to an EDC such as oestrogen causes a reduction in Sertoli cells
produced. The reduction of Sertoli cells causes a decrease in the production of sperm thus
rendering the male reproductive system less effective. EDCs have also been linked to
early puberty, infertility, and developmental defects. Not only have these effects been
found in human subjects, but aquatic life has also been studied as these animals are in
direct contact with EDCs as a part of their lifestyle. Populations of fish have been largely
affected by EDCs prevalence in their native ecosystems. Sex is influenced by water
pollutants that are encountered in every-day life. These sources of water can range from
the simplicity of a water fountain to the entirety of the oceans. The pollutants within the
water range from Endocrine Disruptor Chemicals (EDCs) in birth control to Bisphenol-A
(BPA). Foreign substances such as chemical pollutants that cause an alteration of sex
have been found in growing prevalence in the circulating waters of the world. These
pollutants have affected not only humans, but also animals in contact with the pollutants.

Soil Pollution

Soil contamination or soil pollution is caused by the presence of xenobiotic

chemicals or other alteration in the natural soil environment.
This type of contamination typically arises from the failure caused by corrosion of
underground storage tanks (including piping used to transmit the contents), application of
pesticides, percolation of contaminated surface water to subsurface strata, oil and fuel
dumping, disposal of coal ash, leaching of wastes from landfills or direct discharge of
industrial wastes to the soil. The most common chemicals involved are petroleum
hydrocarbons, lead, polynuclear aromatic hydrocarbons (such as naphthalene and benzo
pyrene), solvents, pesticides, and other heavy metals. This occurrence of this
phenomenon is correlated with the degree of industrialization and intensities of chemical
usage. The concern over soil contamination stems primarily from health risks, from direct
contact with the contaminated soil, vapors from the contaminants, and from secondary
contamination of water supplies within and underlying the soil. Mapping of contaminated
soil sites and the resulting cleanup are time consuming and expensive tasks, requiring
extensive amounts of geology, hydrology, chemistry, computer modeling skills, and GIS
in Environmental Contamination, as well as an appreciation of the history of industrial
chemistry.
It is in North America and Western Europe that the extent of contaminated land is most
well known, with many of countries in these areas having a legal framework to identify
and deal with this environmental problem; this however may well be just the tip of the
iceberg with developing countries very likely to be the next generation of new soil
contamination cases.
The immense and sustained growth of the People's Republic of China since the 1970s has
exacted a price from the land in increased soil pollution. The State Environmental
Protection Administration believes it to be a threat to the environment, to food safety and
to sustainable agriculture. According to a scientific sampling, 150 million mi (100,000
square kilometers) of Chinas cultivated land have been polluted, with contaminated
water being used to irrigate a further 32.5 million mi (21,670 square kilometers) and
another 2 million mi (1,300 square kilometers) covered or destroyed by solid waste. In

total, the area accounts for one-tenth of Chinas cultivatable land, and is mostly in
economically developed areas. An estimated 12 million tonnes of grain are contaminated
by heavy metals every year, causing direct losses of 20 billion yuan (US$2.57 billion).

Causes
This type of contamination or pollution typically arises from failure due to corrosion of
underground storage tanks or of the piping associated with them, historical disposal of
coal ash, application of pesticides, percolation of contaminated surface water to
subsurface strata, oil and fuel dumping, leaching of wastes from landfills or direct
discharge of industrial wastes to the soil. The most common chemicals involved are
petroleum hydrocarbons, solvents, lead, pesticides, and other heavy metals. The
occurrence of this phenomenon is correlated with the degree of industrialization and
intensities of chemical usage.
Historical deposition of coal ash used for residential, commercial, and industrial heating,
as well as for industrial processes such as ore smelting, is a common source of
contamination in areas that were industrialized before about 1960. Coal naturally
concentrates lead and zinc during its formation, as well as other heavy metals to a lesser
degree. When the coal is burned, most of these metals become concentrated in the ash
(the principal exception being mercury). Coal ash and slag may contain sufficient lead to
qualify as a "characteristic hazardous waste", defined in the USA as containing more than
5 mg/L of extractable lead using the TCLP procedure. In addition to lead, coal ash
typically contains variable but significant concentrations of polynuclear aromatic
hydrocarbons (PAHs; e.g., benzo anthracene, benzo fluoranthene, benzo(k)fluoranthene,
benzo pyrene, indeno pyrene, phenanthrene, anthracene, and others). These PAHs are
known human carcinogens and the acceptable concentrations of them in soil are typically
around 1 mg/kg. Coal ash and slag can be recognized by the presence of off-white grains
in soil, gray heterogeneous soil, or (coal slag) bubbly, vesicular pebble-sized grains.
Treated sewage sludge, known in the industry as biosolids, has become controversial as a
fertilizer to the land. As it is the byproduct of sewage treatment, it generally contains
contaminants such as organisms, pesticides.

Effects of Soil Pollution

Health effects
Contaminated or polluted soil directly affects human health through direct contact with
soil or via inhalation of soil contaminants which have vaporized; potentially greater
threats are posed by the infiltration of soil contamination into groundwater aquifers used
for human consumption, sometimes in areas apparently far removed from any apparent
source of above ground contamination. Health consequences from exposure to soil
contamination vary greatly depending on pollutant type, pathway of attack and
vulnerability of the exposed population. Chronic exposure to chromium, lead and other
metals, petroleum, solvents, and many pesticide and herbicide formulations can be
carcinogenic, can cause congenital disorders, or can cause other chronic health
conditions. Industrial or man-made concentrations of naturally occurring substances, such
as nitrate and ammonia associated with livestock manure from agricultural operations,
have also been identified as health hazards in soil and groundwater.
Chronic exposure to benzene at sufficient concentrations is known to be associated with
higher incidence of leukemia. Mercury and cyclodienes are known to induce higher
incidences of kidney damage, some irreversible. PCBs and cyclodienes are linked to liver
toxicity. Organophosphates and carbomates can induce a chain of responses leading to
neuromuscular blockage. Many chlorinated solvents induce liver changes, kidney
changes and depression of the central nervous system. There is an entire spectrum of
further health effects such as headache, nausea, fatigue, eye irritation and skin rash for the
above cited and other chemicals. At sufficient dosages a large number of soil
contaminants can cause death by exposure via direct contact, inhalation or ingestion of
contaminants in groundwater contaminated through soil. The Scottish Government has
commissioned the Institute of Occupational Medicine to undertake a review of methods
to assess risk to human health from contaminated land. The overall aim of the project is
to work up guidance that should be useful to Scottish Local Authorities in assessing

whether sites represent a significant possibility of significant harm (SPOSH) to human

health. It is envisaged that the output of the project will be a short document providing
high level guidance on health risk assessment with reference to existing published
guidance and methodologies that have been identified as being particularly relevant and
helpful. The project will examine how policy guidelines have been developed for
determining the acceptability of risks to human health and propose an approach for
assessing what constitutes unacceptable risk in line with the criteria for SPOSH as
defined in the legislation and the Scottish Statutory Guidance.

Ecosystem effects
Not unexpectedly, soil contaminants can have significant deleterious consequences for
ecosystems. There are radical soil chemistry changes which can arise from the presence
of many hazardous chemicals even at low concentration of the contaminant species.
These changes can manifest in the alteration of metabolism of endemic microorganisms
and arthropods resident in a given soil environment. The result can be virtual eradication
of some of the primary food chain, which in turn could have major consequences for
predator or consumer species. Even if the chemical effect on lower life forms is small, the
lower pyramid levels of the food chain may ingest alien chemicals, which normally
become more concentrated for each consuming rung of the food chain. Many of these
effects are now well known, such as the concentration of persistent DDT materials for
avian consumers, leading to weakening of egg shells, increased chick mortality and
potential extinction of species.
Effects occur to agricultural lands which have certain types of soil contamination.
Contaminants typically alter plant metabolism, often causing a reduction in crop yields.
This has a secondary effect upon soil conservation, since the languishing crops cannot
shield the Earth's soil from erosion. Some of these chemical contaminants have long halflives and in other cases derivative chemicals are formed from decay of primary soil
contaminants.

Mental health effects

The consequences of low-level radiation are often more psychological than radiological.
Because damage from very-low-level radiation cannot be detected, people exposed to it
are left in anguished uncertainty about what will happen to them. Many believe they have
been fundamentally contaminated for life and may refuse to have children for fear of
birth defects. They may be shunned by others in their community who fear a sort of
mysterious contagion.
Forced evacuation from a radiation or nuclear accident may lead to social isolation,
anxiety, depression, psychosomatic medical problems, reckless behavior, even suicide.
Such was the outcome of the 1986 Chernobyl nuclear disaster in the Ukraine. A
comprehensive 2005 study concluded that "the mental health impact of Chernobyl is the
largest public health problem unleashed by the accident to date".
Frank N. von Hippel, a U.S. scientist, commented on the
2011 Fukushima nuclear disaster, saying that "fear of ionizing radiation could have longterm psychological effects on a large portion of the population in the contaminated
areas".
Such great psychological danger does not accompany other materials that put people at
risk of cancer and other deadly illness. Visceral fear is not widely aroused by, for
example, the daily emissions from coal burning, although, as a National Academy of
Sciences study found, this causes 10,000 premature deaths a year in the US. It is "only
nuclear radiation that bears a huge psychological burden for it carries a unique
historical legacy"

Noise pollution

Defination
Noise pollution is excessive, displeasing human, animal, or machine-created
environmental noise that disrupts the activity or balance of human or animal life. The
word noise may be from the Latin word nauseas, which means disgust or discomfort. The
source of most outdoor noise worldwide is mainly construction and transportation
systems, including motor vehicle noise, aircraft noise, and rail noise. Poor urban planning
may give rise to noise pollution, since side-by-side industrial and residential buildings
can result in noise pollution in the residential area.
High noise levels can contribute to cardiovascular effects in humans, a rise in blood
pressure, and an increase in stress and vasoconstriction, and an increased incidence of
coronary artery disease. In animals, noise can increase the risk of death by altering
predator or prey detection and avoidance, interfere with reproduction and navigation, and
contribute to permanent hearing loss.

Human health
Noise pollution effects both health and behavior. Unwanted sound (noise) can damage
physiological and psychological health. Noise pollution can cause annoyance and
aggression, hypertension, high stress levels, tinnitus, hearing loss, sleep disturbances, and
other harmful effects. Furthermore, stress and hypertension are the leading causes to
health problems.
Chronic exposure to noise may cause noise-induced hearing loss. Older males exposed to
significant occupational noise demonstrate significantly reduced hearing sensitivity than
their non-exposed peers, though differences in hearing sensitivity decrease with time and
the two groups are indistinguishable by age 79. A comparison of Maaban tribesmen, who
were insignificantly exposed to transportation or industrial noise, to a typical U.S.
population showed that chronic exposure to moderately high levels of environmental
noise contributes to hearing loss.

High noise levels can contribute to cardiovascular effects and exposure to moderately
high levels during a single eight hour period causes a statistical rise in blood pressure of
five to ten points and an increase in stress and vasoconstriction leading to the increased
blood pressure noted above as well as to increased incidence of coronary artery disease.
Noise pollution is also a cause of annoyance. A 2005 study by Spanish researchers found
that in urban areas households are willing to pay approximately four Euros per decibel
per year for noise reduction.

Wildlife health
Noise can have a detrimental effect on animals, increasing the risk of death by changing
the delicate balance in predator or prey detection and avoidance, and interfering the use
of the sounds in communication especially in relation to reproduction and in navigation.
Acoustic overexposure can lead to temporary or permanent loss of hearing. An impact of
noise on animal life is the reduction of usable habitat that noisy areas may cause, which
in the case of endangered species may be part of the path to extinction. Noise pollution
has caused the death of certain species of whales that beached themselves after being
exposed to the loud sound of military sonar (see also Marine mammals and sonar).
Noise also makes species communicate louder, which is called Lombard vocal
response. Scientists and researchers have conducted experiments that show whales' song
length is longer when submarine-detectors are on. If creatures do not "speak" loud
enough, their voice will be masked by anthropogenic sounds. These unheard voices might
be warnings, finding of prey, or preparations of net-bubbling. When one species begins
speaking louder, it will mask other species' voice, causing the whole ecosystem to
eventually speak louder.
European Robins living in urban environments are more likely to sing at
night in places with high levels of noise pollution during the day, suggesting that they
sing at night because it is quieter, and their message can propagate through the
environment more clearly. The same study showed that daytime noise was a stronger

predictor of nocturnal singing than night-time light pollution, to which the phenomenon
is often attributed.
Zebra finches become less faithful to their partners when exposed to traffic
noise. This could alter a population's evolutionary trajectory by selecting traits, sapping
resources normally devoted to other activities and thus lead to profound genetic and
evolutionary consequences.

Mitigation and control of noise

Roadway noise can be reduced by the use of noise barriers, limitation of vehicle speeds,
alteration of roadway surface texture, limitation of heavy vehicles, use of traffic controls
that smooth vehicle flow to reduce braking and acceleration, and tire design. An
important factor in applying these strategies is a computer model for roadway noise, that
is capable of addressing local topography, meteorology, traffic operations and
hypothetical mitigation. Costs of building-in mitigation can be modest, provided these
solutions are sought in the planning stage of a roadway project.
Aircraft noise can be reduced by using quieter jet engines. Altering flight paths and time
of day runway has benefitted residents near airports.
Industrial noise has been addressed since the 1930s via redesign of industrial equipment,
shock mounted assemblies and physical barriers in the workplace.

Visual Pollution

Visual pollution is the term given to unattractive and man-made

visual elements of a vista, a landscape, or any other thing that a person does not feel
comfortable looking at. Visual pollution is an aesthetic issue, referring to the impacts of
pollution that impair one's ability to enjoy a vista or view. The term is used broadly to
cover visibility, limits on the ability to view distant objects, as well as the more subjective
issue of visual clutter. In other words, pollution is contamination of the environment as a
result of human activities. The term pollution refers primarily to the fouling of air, water,
and land by wastes (see air pollution; water pollution; solid waste). In recent years it has
come to signify a wider range of disruptions to environmental quality. Thus litter,
billboards, and auto junkyards are said to constitute visual pollution; noise excessive
enough to cause psychological or physical damage is considered noise pollution; and
waste heat that alters local climate or affects fish populations in rivers is designated
thermal pollution. Its other reference is to "marketing advertisements"

Thermal pollution
Thermal pollution is the degradation of water quality by any process that changes
ambient water temperature.
A common cause of thermal pollution is the use of water as a coolant by power plants and
industrial manufacturers. When water used as a coolant is returned to the natural
environment at a higher temperature, the change in temperature decreases oxygen supply,
and affects ecosystem composition. Urban runoffstormwater discharged to surface
waters from roads and parking lotscan also be a source of elevated water temperatures.
When a power plant first opens or shuts down for repair or other causes, fish and other
organisms adapted to particular temperature range can be killed by the abrupt change in
water temperature known as elevated temperature typically decreases the level of
dissolved oxygen in water. This can harm aquatic animals such as fish, amphibians and
other aquatic organisms. Thermal pollution may also increase the metabolic rate of

aquatic animals, as enzyme activity, resulting in these organisms consuming more food in
a shorter time than if their environment were not changed. An increased metabolic rate
may result in fewer resources; the more adapted organisms moving in may have an
advantage over organisms that are not used to the warmer temperature. As a result, food
chains of the old and new environments may be compromised. Some fish species will
avoid stream segments or coastal areas adjacent to a thermal discharge. Biodiversity can
be decreased as a result. High temperature limits oxygen dispersion into deeper waters,
contributing to anaerobic conditions. This can lead to increased bacteria levels when there
is ample food supply. Many aquatic species will fail to reproduce at elevated
temperatures.
Primary producers are affected by warm water because higher water temperature
increases plant growth rates, resulting in a shorter lifespan and species overpopulation.
This can cause an algae bloom which reduces oxygen levels.
Temperature changes of even one to two degrees Celsius can cause significant changes in
organism metabolism and other adverse cellular biology effects. Principal adverse
changes can include rendering cell walls less permeable to necessary osmosis,
coagulation of cell proteins, and alteration of enzyme metabolism. These cellular level
effects can adversely affect mortality and reproduction.
A large increase in temperature can lead to the denaturing of life-supporting enzymes by
breaking down hydrogen- and disulphide bonds within the quaternary structure of the
enzymes. Decreased enzyme activity in aquatic organisms can cause problems such as the
inability to break down lipids, which leads to malnutrition.
In limited cases, warm water has little deleterious effect and may even lead to improved
function of the receiving aquatic ecosystem. This phenomenon is seen especially in
seasonal waters and is known as thermal enrichment. An extreme case is derived from
the aggregational habits of the manatee, which often uses power plant discharge sites
during winter. Projections suggest that manatee populations would decline upon the
removal of these discharges.

Cold water
Releases of unnaturally cold water from reservoirs can dramatically change the fish and
macroinvertebrate fauna of rivers, and reduce river productivity. In Australia, where
many rivers have warmer temperature regimes, native fish species have been eliminated,
and macroinvertebrate fauna have been drastically altered. Due to the sudden fall of water
temperature the contraction on dam and bridge pylon may take place.

Control of thermal pollution:

1. Industrial wastewater
In the United States, about 75 to 82 percent of thermal pollution is generated by power
plants. The remainder is from industrial sources such as petroleum refineries, pulp and
paper mills, chemical plants, steel mills and smelters. Heated water from these sources
may be controlled with:

cooling ponds, man-made bodies of water designed for cooling by evaporation,

convection, and radiation

cooling towers, which transfer waste heat to the atmosphere through evaporation
and/or heat transfer

cogeneration, a process where waste heat is recycled for domestic and/or

industrial heating purposes.

Some facilities use once-through cooling (OTC) systems which do not reduce
temperature as effectively as the above systems. For example, the Potrero Generating
Station in San Francisco, which uses OTC, discharges water to San Francisco Bay
approximately 10C (20F) above the ambient bay temperature.

Urban runoff

During warm weather, urban runoff can have significant thermal impacts on small
streams, as stormwater passes over hot parking lots, roads and sidewalks. Stormwater
management facilities that absorb runoff or direct it into groundwater, such as
bioretention systems and infiltration basins, can reduce these thermal effects. Retention
basins tend to be less effective at reducing temperature, as the water may be heated by the
sun before being discharged to a receiving stream.

Causes of Pollution
Pollution is a human contribution to nature. Science has evolved technologies and
technologies have helped the human welfare. In the process, the pollution has been a part
of technology and therefore a part of human miseries.

Human activities mainly include:

Industries for various human needs - directly and indirectly

Agriculture for food production and industrial needs

Health care for health of human beings and animals

Transport for mobility of human beings

Dwelling for settlement in city or villages

Energy for various direct human needs and industrial needs.

All of them contribute to pollution in one way or other and therefore cause miseries. All
of them are aimed to be part of human welfare programmes. Along with welfare, all of
them have brought the maladies of pollution.
Each one is discussed in detail as below. The pollutant (a material causing pollution) may
greatly differ and dimension of problem may also greatly differ in such causes.

Disadvantages of pollution

Lack of ability to hear important sounds clearly

leading to lability to hear oncoming danger,

Inability to hear common conversation,

Tinnitus,

Distortion of speech or music,

Mental stress from the constant and unremitting noise,

Confusion,

Deterioration of general health.

The economic price of pollution is incaluable and the resulting effect it will have
on climate change is going to have an enormous effect on future generations.
People and animals can get ill. plants and animals can

leech into the soil. water sources become

die.

toxins

polluted. increase in amount of CO2

and ammonia.

Never mind that, thats your cigarette or cigar, they think.But if you smoke, you
may remind them that their body temperature is higher than tolerable about global
warming.

Water pollution

Water pollution is the contamination of water bodies (e.g. lakes, rivers,

oceans, aquifers and groundwater). Water pollution occurs when pollutants are discharged
directly or indirectly into water bodies without adequate treatment to remove harmful
compounds.
Water pollution affects plants and organisms living in these bodies of water. In almost all
cases the effect is damaging not only to individual species and populations, but also to the
natural biological communities.

Categories
Surface water and groundwater have often been studied and
managed as separate resources, although they are interrelated. Surface water seeps
through the soil and becomes groundwater. Conversely, groundwater can also feed
surface water sources. Sources of surface water pollution are generally grouped into two
categories based on their origin.

Point sources
Point source water pollution refers to contaminants that enter a waterway from a single,
identifiable source, such as a pipe or ditch. Examples of sources in this category include
discharges from a sewage treatment plant, a factory, or a city storm drain. The U.S. Clean
Water Act (CWA) defines point source for regulatory enforcement purposes. The CWA
definition of point source was amended in 1987 to include municipal storm sewer
systems, as well as industrial stormwater, such as from construction sites.

Groundwater pollution
Interactions between groundwater and surface water are complex. Consequently,
groundwater pollution, sometimes referred to as groundwater contamination, is not
as easily classified as surface water pollution. By its very nature, groundwater
aquifers are susceptible to contamination from sources that may not directly affect
surface water bodies, and the distinction of point vs. non-point source may be
irrelevant. A spill or ongoing releases of chemical or radionuclide contaminants into
soil (located away from a surface water body) may not create point source or nonpoint source pollution, but can contaminate the aquifer below, defined as a toxin
plume. The movement of the plume, called a plume front, may be analyzed through
a hydrological transport model or groundwater model. Analysis of groundwater
contamination may focus on the soil characteristics and site geology, hydrogeology,
hydrology, and the nature of the contaminants.

Causes
The specific contaminants leading to pollution in water include a wide spectrum of
chemicals, pathogens, and physical or sensory changes such as elevated temperature and
discoloration. While many of the chemicals and substances that are regulated may be
naturally occurring (calcium, sodium, iron, manganese, etc.) the concentration is often the
key in determining what is a natural component of water, and what is a contaminant.
High concentrations of naturally occurring substances can have negative impacts on
aquatic flora and fauna.
Oxygen-depleting substances may be natural materials, such as plant matter (e.g. leaves
and grass) as well as man-made chemicals. Other natural and anthropogenic substances
may cause turbidity (cloudiness) which blocks light and disrupts plant growth, and clogs
the gills of some fish species. Many of the chemical substances are toxic. Pathogens can
produce waterborne diseases in either human or animal hosts. Alteration of water's
physical chemistry includes acidity (change in pH), electrical conductivity, temperature,
and eutrophication. Eutrophication is an increase in the concentration of chemical

nutrients in an ecosystem to an extent that increases in the primary productivity of the

ecosystem. Depending on the degree of eutrophication, subsequent negative
environmental effects such as anoxia (oxygen depletion) and severe reductions in water
quality may occur, affecting fish and other animal populations.

Chemical and other contaminants

Organic water pollutants include:

Detergents

Disinfection by-products found in chemically disinfected drinking water, such as

chloroform

Food processing waste, which can include oxygen-demanding substances, fats

and grease

Insecticides and herbicides, a huge range of organ halides and other chemical
compounds

Petroleum hydrocarbons, including fuels (gasoline, diesel fuel, jet fuels, and fuel
oil) and lubricants (motor oil), and fuel combustion byproducts, from stormwater
runoff

Tree and bush debris from logging operations

Volatile organic compounds (VOCs), such as industrial solvents, from improper

storage.

Chlorinated solvents, which are dense non-aqueous phase liquids (DNAPLs), may
fall to the bottom of reservoirs, since they don't mix well with water and are
denser.
o

Polychlorinated biphenyl (PCBs)

Trichloroethylene

Perchlorate

Various chemical compounds found in personal hygiene and cosmetic products.

Non organic water pollutants include:

Acidity caused by industrial discharges (especially sulfur dioxide from power

plants)

Ammonia from food processing waste

Chemical waste as industrial by-products

Fertilizers containing nutrients--nitrates and phosphateswhich are found in

stormwater runoff from agriculture, as well as commercial and residential use[

Heavy metals from motor vehicles (via urban stormwater runoff) and acid mine
drainage

Silt (sediment) in runoff from construction sites, logging, slash and burn practices
or land clearing sites.

List of environmental issues

This is a list of environmental issues that are due to human activity.

Climate change
Fossil fuels
Sea level rise
Effects of the automobile on societies
Conservation Genetic erosion Holocene extinction event Invasivespecies
Species extinction Habitat destruction Habitat fragmentation Pollinator decline
Coral bleaching Whaling Beached whale

 Energy - Energy conservation Renewable energy Efficient energy use Renewable

energy commercialization

Intensive farming Overgrazing Irrigation Monoculture Environmental

effects of meat production

Land degradation Land pollution Desertification

Soil Soil conservation Soil erosion Soil contamination Soil salination
Nanotechnology Nanotoxicology Nanopollution
Nuclear issues Nuclear fallout Nuclear meltdown Nuclear power

Water pollution Acid rain Eutrophication Ocean dumping Oil spills

Water crisis

Resource depletion Exploitation of natural resources

Fishing Blast fishing Bottom trawling
Cyanide fishing Ghost nets Illegal,
unreported and unregulated fishing
Environmental effects of
fishing Overfishing

Logging Clearcutting Deforestation

Illegal logging

Mining Acid mine drainage

Toxins ;
Chlorofluorocarbons DDT Dioxin Heavy metals Herbicides
Pesticides Toxics use reduction Toxic waste

Sources and causes

Air pollution produced by ships may alter clouds, affecting global temperatures.
Air pollution comes from both natural and human-made (anthropogenic) sources.
However, globally human-made pollutants from combustion, construction, mining,
agriculture and warfare are increasingly significant in the air pollution equation.[20]
Motor vehicle emissions are one of the leading causes of air pollution. China, United
States, Russia, India Mexico, and Japan are the world leaders in air pollution emissions.
Principal stationary pollution sources include chemical plants, coal-fired power plants, oil
refineries, petrochemical plants, nuclear waste disposal activity, incinerators, large
livestock farms (dairy cows, pigs, poultry, etc.), PVC factories, metals production
factories, plastics factories, and other heavy industry. Agricultural air pollution comes
from contemporary practices which include clear felling and burning of natural
vegetation as well as spraying of pesticides and herbicides
About 400 million metric tons of hazardous wastes are generated each year. The United
States alone produces about 250 million metric tons. Americans constitute less than 5%
of the world's population, but produce roughly 25% of the worlds CO2, and generate
approximately 30% of worlds waste. In 2007, China has overtaken the United States as
the world's biggest producer of CO2, while still far behind based on per capita pollution ranked 78th among the world's nations.

An industrial area, with a power plant, south of Yangzhou's downtown, China

In February 2007, a report by the Intergovernmental Panel on Climate Change (IPCC),

representing the work of 2,500 scientists, economists, and policymakers from more than
120 countries, said that humans have been the primary cause of global warming since
1950. Humans have ways to cut greenhouse gas emissions and avoid the consequences of
global warming, a major climate report concluded. But to change the climate, the
transition from fossil fuels like coal and oil needs to occur within decades, according to
the final report this year from the UN's Intergovernmental Panel on Climate Change
(IPCC).
Some of the more common soil contaminants are chlorinated hydrocarbons (CFH), heavy
metals (such as chromium, cadmiumfound in rechargeable batteries, and leadfound in
lead paint, aviation fuel and still in some countries, gasoline), MTBE, zinc, arsenic and
benzene. In 2001 a series of press reports culminating in a book called Fateful Harvest
unveiled a widespread practice of recycling industrial byproducts into fertilizer, resulting
in the contamination of the soil with various metals. Ordinary municipal landfills are the
source of many chemical substances entering the soil environment (and often
groundwater), emanating from the wide variety of refuse accepted, especially substances
illegally discarded there, or from pre-1970 landfills that may have been subject to little
control in the U.S. or EU. There have also been some unusual releases of polychlorinated
dibenzodioxins, commonly called dioxins for simplicity, such as TCDD.
Pollution can also be the consequence of a natural disaster. For example, hurricanes often
involve water contamination from sewage, and petrochemical spills from ruptured boats
or automobiles. Larger scale and environmental damage is not uncommon when coastal
oil rigs or refineries are involved. Some sources of pollution, such as nuclear power
plants or oil tankers, can produce widespread and potentially hazardous releases when
accidents occur.
In the case of noise pollution the dominant source class is the motor vehicle, producing
about ninety percent of all unwanted noise worldwide.

Pollution control is the process of reducing or eliminating the release of pollutants

(contaminants, usually human-made) into the environment. It is regulated by various
environmental agencies that establish limits for the discharge of pollutants into the air,
water, and land. A wide variety of devices and systems have been developed to control air
and water pollution and solid wastes.

Air pollution control

Methods of air pollution control can be divided into two categories: the control of
particulate (pronounced par-TIK-you-let) emissions and the control of gaseous emissions.
The term particulate refers to tiny particles of matter such as smoke, soot, and dust that
are released during industrial, agricultural, or other activities. Gaseous emissions are
industrial products such as sulfur dioxide, carbon monoxide, and oxides of nitrogen also
released during various manufacturing operations.

Particulate control.Methods for particulate control tend to operate on a common

principle. The solid particles are separated from the gases in which they are contained by
physical procedures such as passage through a settling chamber. A settling chamber is a
long, wide pipe through which gases from a manufacturing process are allowed to flow.
As these gases slow down in the pipe, the solid particles settle out. They can then be
removed from the bottom of the pipe.
A cyclone collector is another device for removing particulates from stack gases. The
gases are fed into a rotating cylindrical container.

Equipment for the complete recovery and control of acid and oxide emissions.
Centrifugal forces (the forces that move things away from the center of rotation) send
solid particles in the gas outward against the walls of the container. They collect there
briefly, then fall to the bottom of the container. Gases from which the particles have been
removed then escape from the top of the container.

Gaseous emission.Many different methods are available for removing unwanted

gases, most of which are acidic. Scrubbers are smokestack devices that contain a moist
chemical such as lime, magnesium oxide, or sodium hydroxide. When gases escape from
a factory and pass through a scrubber, they react with the moist chemical and are
neutralized. From time to time, the scrubbers are removed from the smokestack, cleaned,
and replaced.
Another method for controlling gaseous emissions is by adsorption. Activated charcoal is
charcoal that has been ground into a very fine powder. In this form, charcoal has the
ability to adsorb, or adhere to, other chemicals. When unwanted gases flow over activated
charcoal on the inside of a smokestack, they are adsorbed on the charcoal. As with
scrubbers, the charcoal is removed from time to time, and a new lining of charcoal is
installed in the smokestack.

Water pollution
Methods of controlling water pollution fall into three general categories: physical,
chemical, and biological. For example, one form of water pollution consists of suspended
solids such as fine dirt and dead organisms. These materials can be removed from water
by simply allowing the water to sit quietly for a period of time, thereby allowing the
pollutants to settle out, or by passing the water through a filter. (The solid pollutants are
then trapped in the filter.)
Chemical reactions can be used to remove pollutants from water. For example, the
addition of alum (potassium aluminum sulfate) and lime (calcium hydroxide) to water
results in the formation of a thick, sticky precipitate. When the precipitate begins to settle
out, it traps and carries with it solid particles, dead bacteria, and other components of
polluted water.
Biological agents can also be used to remove pollutants from water. Aerobic bacteria
(those that need oxygen to survive) and anaerobic bacteria (those that do not require
oxygen) attack certain chemicals in polluted water and convert them to a harmless form.

Solid pollutants
Solid pollutants consist of garbage, sewage sludge, paper, plastics, and many other forms
of waste materials. One method of dealing with solid pollutants is simply to bury them in
dumps or landfills. Another approach is to compost them, a process in which
microorganisms turn certain types of pollutants into useful fertilizers. Finally, solid
pollutants can also be incinerated (burned).

Taking on pollution: a global attempt

While artificial chemicals have improved the quality of life around the world, they have
also posed a threat to the health of people and wildlife. In late 2000, in an effort to control
the effect of toxic global pollutants, the United Nations Environment Program organized
a meeting to draft a treaty to restrict the production and use of twelve persistent organic
pollutants (POPs), especially those used as pesticides. The twelve toxic chemicals cited,
which environmentalists have called the "dirty dozen," include eight pesticides (aldrin,
chlordane, DDT, dieldrin, endrin, heptachlor, mirex, and toxaphene), two types of
industrial chemicals (hexachlorobenzene and polychlorinated biphenyls or PCBs), and
two types of industrial byproducts (dioxins and furans). These toxic pollutants were
chosen not because they are the most dangerous, but because they are the most widely
studied. Since it is still widely used in Africa to control malaria, DDT was given a special
exemption: it can be used in those countries until replacement chemicals or strategies can
be developed and put into place. One hundred and twenty-two nations (including the
United States) agreed to the treaty. Before it can take effect, however, at least fifty of
those nations must also ratify it.

Possible future approach to cleaning up pollution

The cost of cleaning up tens of thousands of toxic sites on factory grounds, farms, and
military installations is staggering. In the United States, that amount may soon exceed
$700 billion. So far, the main approach has been to dig the polluting chemicals out of the
ground and transport them to a landfill. However, after a decade of research, scientists in

the early twenty-first century found that hundreds of species of plants, along with the
fungi and bacteria that inhabit the ecosystem around their roots, seek out and often break
down chemical molecules that can harm most other life. For example, there are
sunflowers that capture uranium, ferns that thrive on arsenic, clovers that eat oil, and
poplar trees that destroy dry-cleaning solvents. Research into using plants as pollution
sponges must continue, but early reports of their helping to clean up pollution were
promising

Pollution control
Pollution control is a term used in environmental management. It means the control of
emissions and effluents into air, water or soil. Without pollution control, the waste
products from consumption, heating, agriculture, mining, manufacturing, transportation
and other human activities, whether they accumulate or disperse, will degrade the
environment. In the hierarchy of controls, pollution prevention and waste minimization
are more desirable than pollution control. In the field of land development, low impact
development is a similar technique for the prevention of urban runoff.

Practices

recycling

reusing

Waste minimisation

mitigating

preventing

compost

Pollution control devices

Dust collection systems

o

Bag houses

Cyclones

Electrostatic precipitators

Scrubbers
o

Baffle spray scrubber

Cyclonic spray scrubber

Ejector venturi scrubber

Mechanically aided scrubber

Spray tower

Wet scrubber

Sewage treatment
o

Sedimentation (Primary treatment)

Activated sludge biotreaters (Secondary treatment; also used for industrial

wastewater)

Aerated lagoons

Constructed wetlands (also used for urban runoff)

Industrial wastewater treatment

o

API oil-water separators

Biofilters

Dissolved air flotation (DAF)

Powdered activated carbon treatment

Ultrafiltration

Vapor recovery systems

Phytoremediation

Perspectives
The earliest precursor of pollution generated by life forms would have been a natural
function of their existence. The attendant consequences on viability and population levels
fell within the sphere of natural selection. These would have included the demise of a
population locally or ultimately, species extinction. Processes that were untenable would
have resulted in a new balance brought about by changes and adaptations. At the

extremes, for any form of life, consideration of pollution is superseded by that of

survival.
For humankind, the factor of technology is a distinguishing and critical consideration,
both as an enabler and an additional source of byproducts. Short of survival, human
concerns include the range from quality of life to health hazards. Since science holds
experimental demonstration to be definitive, modern treatment of toxicity or
environmental harm involves defining a level at which an effect is observable. Common
examples of fields where practical measurement is crucial include automobile emissions
control, industrial exposure (e.g. Occupational Safety and Health Administration (OSHA)
PELs), toxicology (e.g. LD), and medicine (e.g. medication and radiation doses).
"The solution to pollution is dilution", is a dictum which summarizes a traditional
approach to pollution management whereby sufficiently diluted pollution is not harmful.
It is well-suited to some other modern, locally scoped applications such as laboratory
safety procedure and hazardous material release emergency management. But it assumes
that the dilutant is in virtually unlimited supply for the application or that resulting
dilutions are acceptable in all cases.
Such simple treatment for environmental pollution on a wider scale might have had
greater merit in earlier centuries when physical survival was often the highest imperative,
human population and densities were lower, technologies were simpler and their
byproducts more benign. But these are often no longer the case. Furthermore, advances
have enabled measurement of concentrations not possible before. The use of statistical
methods in evaluating outcomes has given currency to the principle of probable harm in
cases where assessment is warranted but resorting to deterministic models is impractical
or infeasible. In addition, consideration of the environment beyond direct impact on
human beings has gained prominence.
Yet in the absence of a superseding principle, this older approach predominates practices
throughout the world. It is the basis by which to gauge concentrations of effluent for legal
release, exceeding which penalties are assessed or restrictions applied. One such

superseding principle is contained in modern hazardous waste laws in developed

countries, as the process of diluting hazardous waste to make it non-hazardous is usually
a regulated treatment process.[51] Migration from pollution dilution to elimination in many
cases can be confronted by challenging economical and technological barriers.

Greenhouse gases and global warming

Carbon dioxide, while vital for photosynthesis, is sometimes referred to as pollution,
because raised levels of the gas in the atmosphere are affecting the Earth's climate.
Disruption of the environment can also highlight the connection between areas of
pollution that would normally be classified separately, such as those of water and air.
Recent studies have investigated the potential for long-term rising levels of atmospheric
carbon dioxide to cause slight but critical increases in the acidity of ocean waters, and the
possible effects of this on marine ecosystems.

Most polluted places in the developing world

The Blacksmith Institute, an international non-for-profit organization dedicated to
eliminating life-threatening pollution in the developing world, issues an annual list of
some of the world's worst polluted places. In the 2007 issues the ten top nominees,
already industrialized countries excluded, are located in Azerbaijan, China, India, Peru,
Russia, Ukraine and Zambia.

Conclusion
Its to be concluded that pollution is very dangerous for this green earth. Now
the days its very important to save earth. If no step would be taken then it will become
serious problem. So it very much important to save this beautiful earth .
Secondly the government should also help to prevent this dangerous
pollution. Government should take some serous steps to take control over pollution.
People who are not obeying rules and regulations , some strict actions shoud be taken
against them.
This problem is very serious, so some serious steps should taken. If no
action is taken it will have o solution. And the end of the earth will be very near.

Suggestions

The Government and the voluntary organisation should take steps to popularise the use of
bio-fertilizers and bio-pesticides, which are having environmental benefits.
1. The owners of big hotels and grocery shops should come forward to change ploy
bags and use paper and cloth bags.
2. The age of marriage for girls should be raised from 18 years to 20 years and of
boys 25 years from the present 21 years. This is under active consideration of the
Central Government and this must be implemented so as to control population
growth.
3. Regular awareness campaigns should be conducted by voluntary organizations to
create awareness about environmental conservation activities.
4. A massive programme of waste land development through forestation and tree
planting with peoples participation should be popularised. This should be done
especially during the monsoon season. The Government and other voluntary
organisation should educate the common mass about the need.

Bibliography

1. Htpp// www.wikipedia.com//polluction//main
2. www.quickmba.com
3. www.scribd.com
4. www.silicon.com
5. http://en.wikipedia