Scribd
Upload
234 views

C&S Loop

1. The document discusses loop antennas for HF reception as an alternative to dipole antennas. It describes how loop antennas can have a low, inductive input impedance and a figure-of-eight azimuth radiation pattern. 2. By terminating the loop with a suitable impedance at the point opposite the feedpoint, the radiation pattern can be modified to a near-cardioidal pattern. This allows the loop to be used in endfire, broadside, or radial arrays. 3. Various array configurations using loops are presented, including endfire arrays for point-to-point communication, broadside arrays for omnidirectional coverage, and radial arrays for steerable coverage similar to rhombic antennas but using

Uploaded by

utammarry
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
234 views

C&S Loop

1. The document discusses loop antennas for HF reception as an alternative to dipole antennas. It describes how loop antennas can have a low, inductive input impedance and a figure-of-eight azimuth radiation pattern. 2. By terminating the loop with a suitable impedance at the point opposite the feedpoint, the radiation pattern can be modified to a near-cardioidal pattern. This allows the loop to be used in endfire, broadside, or radial arrays. 3. Various array configurations using loops are presented, including endfire arrays for point-to-point communication, broadside arrays for omnidirectional coverage, and radial arrays for steerable coverage similar to rhombic antennas but using

Uploaded by

utammarry
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

COMMUNICATIONS 74 CONFERENCE

BRIGHTON
Wednesday, June 5 1974 Session 5,
Equipment
Design
Paper 5.3: Loop Antennas for HF Reception
Contributed by: B.S.Collins,
C & S Antennas Ltd.,
Knight Road,
Rochester, Kent
ME2 2AX

Loop Antennas for HF Reception


B.S. COLLINS
INTRODUCTION
In the HF band the sensitivity of a receiving system is limited by ambient noise in the environment.
Sensitivity is not increased by increasing the size of the signal provided by the antenna but can only
be increased by increasing the directivity of the antenna. It is therefore attractive to consider the
possibility of constructing an array comprising a number of small antennas.
1. Choice of Antenna Unit for Array
The characteristics of short dipoles, whips and loops were considered. Each type of antenna has
various advantages and disadvantages. To take advantage of being able to use a small antenna element it
should be capable of receiving vertically polarised signals, which may be received by an antenna
mounted immediately above ground level, rather than horizontally polarised signals whose field
strength falls at ground level.
A vertical dipole or whip antenna has a high, capacitive input impedance and an omnidirectional
azimuth radiation pattern. The effective height and input impedance may be modified by the addition of
a capacity hat to the top of the whip.
A loopplaced in the vertical planehas a low, inductive input impedance and a figure-of-eight
azimuth radiation pattern.
1.1 Input Impedance
If we further examine the input impedance of the two types of antenna we note that a dipole looks like,
a slightly lossy capacitor. It does not exhibit resonance phenomena over very wide bandsuntil its
dimensions become a substantial fraction of a wavelength. A small loop looks like a slightly lossy
inductor. Unfortunately loops of reasonable size 0.5 to 1.5m diameterexhibit resonances in the HF
band. The series inductance may be reduced by forming the loop from wide strip and the parallel
capacitance may be minimised by careful design of the terminal region.
1.2 Radiation Patterns
As the vertical whip or dipole has an omnidirectional azimuth radiation pattern, all azimuth
directivity must be obtained from the arraying of elements. With any array it will be impossible to
receive signals arriving from high angles of elevation. This is an unfortunate defect.
A loop antenna normally has a bidirectional azimuth radiation pattern, but is able to receive signals
from all angles of elevation. In an endfire array a unidirectionai beam may be formed at any angle of

elevation. The null in the basic pattern of the loop may be used to eliminate unwanted signals.
1 .3 Ideal Element
An ideal element would combine a far more constant input impedance than either of the elements
discussed, together with a unidirectional radiation pattern. An input impedance close to 50 ohms
would be useful, as existing amplifiers and filters could be connected to the element. A unidirectional
azimuth radiation pattern would allow endfire, broadside or radial arrays to be constructed.
It did not seem likely that the desired combination of properties could be obtained from a dipole
element, so the loop element was further investigated.
2. THE RADIATION PATTERN OF LOOP ANTENNAS
The current which flows in a loop antenna may be represented by a Fourier series of cosine and sine
terms. The zero order term represents a constant current flowing around the hop and gives rise to
the familiar figure-of-eight radiation pattern typical of a small loop (Fig. 1 A).
The odd order (sine) terms represent the currents which flow in the same direction in both sides of
the loop and therefore do not give rise to any output voltage across a balanced terminating impedance.
The azimuth radiation pattern associated with this current mode in a small loop is circular. (Fig. 1
B).
When the loop is fed with an unbalanced feed both even and odd modes can exist. The total radiation
pattern of the loop will be the sum of those due to the separate modes. The zero order mode
predominates in a simple loop; in order to obtain a cardioid radiation pattern the amplitude of the
zero order mode current must be reduced relative to the first order mode current, and the relative
phase of the currents must be adjusted so that the cancellation obtained in the rearwards direction is
complete. This result can be achieved by inserting a suitable impedance in series with the loop at a
point diametrically opposite the feedpoint (Fig. 1 C).
The terminated loop exhibits a near cardioidal azimuth radiation pattern for vertically polarised
incident energy and an input impedance which may easily be matched to 50 ohms.
3. DESIRED AMPLIFIER CHARACTERISTIC
The effective height of a terminated loop 0.80m in diameter is approximately 0.7m. In order to
ensure that the received signal is raised to a level at which it will overcome the internal noise of the
receiver and to buffet the output of the loop, a low noise amplifier is connected to the loop output.
The effective height of a halfwave dipole antenna is directly proportional to wavelengthin fact 0.32
wavelengths. Similarly the effective height (or effective area) of any other antenna is proportional
to wavelength. By contrast the effective area of a loop increases as the wavelength decreases. Thus if
the output of the loop is compared with that from some other broadband antenna such as a log periodic
it will be observed that the signal from the loop rises relative to that from the log periodic as the
frequency is increased. To provide a constant ratio between the signals from the two antenna the
amplifier used with the loop must have a gain which falls with frequency. This is a matter of choice
rather than necessity, although in some cases it may avoid blocking of the receiver by signals at the
high frequency end of the band.
In order to avoid disturbance by MF or VHF signals the passband of the amplifier should be restricted
by filtering.
The main problem of amplifier design is that of achieving satisfactory intermodulation performance.
From work carried out so far it is clear that the performance of any active antenna system will be
determined ultimately by intermodulation. The characteristics of transistors which fully determine
linearity are unfortunately not well documented. Amplifiers have been made whose 2nd and 3rd order
intermodulation products are some 60dB below the outputs for an input signal level of + 80dB (,uV).

4. PRACTICAL LOOP ANTENNA


A practical loop antenna is shown in figure 3. The loop is made from aluminium strip embedded in
fibreglass. This construction is light and rigid and gives a low series inductance and shunt
capacitance. The amplifier is housed in a cast box at the base of the loop and the terminating
components in a recess at the top. Radiation patterns from such a loop are illustrated in figure 2.
5. PRACTICAL COMPARISON OF A LOOP WITH A MONOPOLE
In order to assess the practical performance of a loop and amplifier, a comparison has been made
with a conventional quarter wave monopole. The antennas were connected to the two inputs of a dual
path diversity receiver which is used to provide two receivers with well balanced characteristics.
The output from the receiver, which would receive CW, MCW or FSK signals, was displayed on an
oscilloscope and was available on headphones.
Input signals were tuned and the loop aligned for maximum signal. Input and if attenuators were
adjusted until the output levels from the two channels were identical. The noise levels on the two
channels may then be examined with the oscilloscope. The two antennas cannot generally be
distinguished by this test. Signals which are just discernible at low level on the monopole may also
be received using the loop.
When comparing the loop or an array of loops with any conventional array great care must be taken
that the results are strictly comparable. Mere amplitude of the output signal is of no consequence,
for the gain of the amplifier associated with the loop may be changed at will. A comparison between
arrays will only be valid if the arrays concerned have closely similar radiation patterns and are
properly suited to a propagation path over which they are being tested. Much of the work done in
comparing arrays in the past falls down in these respects.
6. PERFORMANCE OF ARRAYS OF LOOPS
The loops may be used in endfire, broadside or radial arrays.
6.1 Endfire Arrays (Fig. 4A)
This type of array is ideal for fixed point-to-point services. An excellent front-to-back ratio can be
maintained over a wide frequency band and the angle of elevation of the main beam can be controlled
by introducing variable phase shift between elements. They cannot be slewed to fire in different
azimuth directions.
6.2 Broadside Arrays (Fig. 4B)
An advantage of using basic elements with a cardioid azimuth radiation pattern is that they can be
employed in broadside arrays as well as endfire arrays.
A broadside array has a broad vertical beam which is narrow in the horizontal plane. The vertical
beamwidth is not a function of frequency so the array can be used at a variety of frequencies on short
circuits. The beam can be slewed over a range of azimuth anglessay +30 from the nominal
direction of fire.
6.3 Radial Arrays (Fig. 4C)
If a fully steerable array is requiredfor example for communication to ships the conventional
solution is to use a rosette of log periodic or rhombic antennas. Such arrays are extremely costly and
occupy very large land areas. For this application
loops may be arranged in a number of concentric rings. By suitably matrixing the outputs of the
individual loops a number of overlapping beams can be created, available singly or concurrently.

CONCLUSION
A loop element with a cardioidal azimuth radiation patterns has been developed and its performance
assessed. Once the problems of intermodulation products have been overcome these elements have
wide application for constructing both simple and highly sophisticated arrays.
Acknowledgements
The author would like to thank his colleague, Dr. K. A.H. Hanna, for his assistance in the preparation
of this paper.
References
1. Kraus, J.D., 'Antennas', McGraw Hill 1950.
2. Collin, R.E. and Zucker, F.J., 'Antenna Theory', (Part 1) McGraw Hill 1969.
Antennas embodying the principles described in this paper are the subject of current Patent
applications.

You might also like