The ACG7 pump can handle flows from 80-1200 l/min at pressures up to 16 bar. It is used for applications like lubrication, circulation, and fluid transfer in industries such as marine, power generation, oil production, and refining. The pump comes in different sizes and configurations to suit various duty conditions and fluid types including oils and other liquids.
The ACG7 pump can handle flows from 80-1200 l/min at pressures up to 16 bar. It is used for applications like lubrication, circulation, and fluid transfer in industries such as marine, power generation, oil production, and refining. The pump comes in different sizes and configurations to suit various duty conditions and fluid types including oils and other liquids.
The ACG7 pump can handle flows from 80-1200 l/min at pressures up to 16 bar. It is used for applications like lubrication, circulation, and fluid transfer in industries such as marine, power generation, oil production, and refining. The pump comes in different sizes and configurations to suit various duty conditions and fluid types including oils and other liquids.
The ACG7 pump can handle flows from 80-1200 l/min at pressures up to 16 bar. It is used for applications like lubrication, circulation, and fluid transfer in industries such as marine, power generation, oil production, and refining. The pump comes in different sizes and configurations to suit various duty conditions and fluid types including oils and other liquids.
Flow volume: 80 - 1200 l/min Max differential pressure: 16 bar Applications: Circulation, lubrication and transfer
1. Applications 1.1 Functionality The Std Line (standard) ACG pumps come in two executions; Lube Line and Fuel Line. The main difference is the shaft seal design, optimized for light duty and heavy duty respectively. The ACG pumps are used for a number of different fluids: Lubrication oil, fuel oil, vegetable oil, hydraulic oil and other hydraulic fluids, polymers, emulsions and any non-aggressive fluid with sufficient lubricating properties. If requested, the ACG pump may be certified according to any of following classification societies: DNV, BV, LRS, ABS, RS, GL, RINA, KR, NK, RMR or CCS.
1.2 Applications Typical applications are: - Lubrication of diesel engines, gears, gas and steam turbines, hydro turbines and paper machines - Circulation for cooling and filtration in large machineries, hydraulic systems and transformer oil for insulation in transformers - As transfer pumps onboard vessels, in power plants, oil factories, refineries, tank farms etc - For supply and circulation systems
1.3 Installation The pump is designed to be flange-mounted to its electric motor via a connecting frame and a flexible shaft coupling. By the angle bracket, the pump might be mounted horizontally or vertically. As standard, the pump is supplied without counter flanges (DIN type) but they can be included if requested. As standard the pump is delivered with the discharge side to the right when seen from the pump shaft side(see below). For more information about installation, see Installation and Start-up instruction for low pressure pumps.
Mounting standard picture M93-0.
www.imo.se
ACG7 1123.02 GB
On request the pump can be delivered in the opposite direction, M39-0.
2. Pump model code
A C G
0 4 5 N 7
N V B P
Pump series ACG (, UCG*) Size
Lead
Power rotor diameter [mm]
045, 052, 060, 070
K = Low lead N = Normal lead D = High lead
Generation Design generation 7 Material in pump body N = Nodular cast iron
Shaft seal design
V = Carbon/Carbide, elastomers in Viton (Lube Line) T = Silicon Carbide/Silicon Carbide, elastomers in Viton
(Fuel Line) Mounting B = Flange mounting F = Foot mounting* Valve
P = Pressure relief valve with spring for max. 16 bar
E = Without valve
Special design Code group omitted for standard design (A-number)
ACG7 1123.02 GB
* For UCG and foot-mounted models, please contact IMO AB.
www.imo.se
3. Technical Data 3.1 Pressure Information Pressure relief valve The pump is equipped with an integral pressure relief valve with internal return, limiting the differential pressure across the pump and protecting the pump. Should the discharge line be blocked, the relief valve will open by the pressure. The valve is adjustable for different opening pressures. The value of the pressure limit can be set at the factory and should be adjusted at installation (see Installation & Start-up instruction for low-pressure pumps). The maximum pressure accumulation varies with pump size, speed and viscosity, but will normally not exceed 4 bar. The valve has a maximum set pressure of 16 bar.
Inlet pressure Minimum inlet pressure (suction capability) is dependent on fluid viscosity and rotation speed. It increases with decreasing viscosity and decreasing speed. Information about minimum inlet pressure for each individual duty case can be obtained from IMO AB or pump selection software WinPump. Maximum inlet pressure is 12 bar.
Discharge pressure Maximum discharge pressure is 16 bar.
Differential pressure Maximum differential pressure is 16 bar but reduced at low viscosities according to table below Viscosity [cSt] 1,4 2 6 10 >12 Max. diff. pressure [bar] 6,9 8,0 12,4 15 16 Refer to your IMO representative or use the pump selection software WinPump to determine the exact operating limits.
3.2 Driver information
Driver type The pump is designed primarily for direct drive through a flexible shaft coupling. Under certain conditions other types of drive can be permitted, e.g. gear or pulley drives, which create radial loads onto the shaft end. Permissible radial force varies with pressure, speed and inlet conditions. For radial load requirements, contact IMO AB.
Speed The maximum speed is 3600 rpm. Max. operating speed may be reduced depending on inlet conditions. Contact IMO or use the pump selection software WinPump to find a corresponding speed limit in order to avoid cavitation problems.
The pump is designed to operate in one rotational direction only, as standard clockwise when facing the shaft end. Pumps for CCW operation can be delivered on special request. For shorter periods of time, a few minutes for emptying a discharge line, the pump may be operated in reverse direction, provided the back pressure is limited to 3 bar.
www.imo.se
ACG7 1123.02 GB
Rotation
3. Technical Data 3.3 Sound level Typical pump sound levels refer to free field conditions at a distance of 1 m from the pump. Noise of driver excluded in the quoted figures. The sound levels are measured at a discharge pressure of 5 bar, speed 2900 rpm and viscosity 37 cSt. Size 045 052 060 070 Sound level dB [A] 59 63 66 68
3.4 Moment of Inertia
Moment of intertia [10-3 kgm2] Size 045 052 060 070 Value 0,26 0,51 1,1 2,2
3.5 Fluid viscosity
Lube Line seal (Seal version code V): 1,4 800 cSt for Lube and hydraulic oil Fuel Line seal (Seal version code T): 1,4 3500 cSt for Fuel oil For higher viscosity, contact IMO AB.
3.6 Fluid temperature
ACG7 1123.02 GB
Lube Line (Seal version code V): -20 +90 C
Fuel Line (Seal version code T): -20 +155 C
www.imo.se
4. Design 4.1 Ball bearing The pump is fitted with an external lubricated ball bearing. When delivered from IMO AB, the ball bearing is filled with grease. For more information, see Maintenance and Service Instructions.
4.2 Material & design
Model
Material pump Material rotor
Material idler
Material seal
Material Elastomers
ACG NVBP
Nodular cast iron
Steel, surface treated
Cast iron, surface treated
Carbon/Silicon Carbide
Viton
ACG NTBP
Nodular cast iron
Steel, surface treated
Cast iron, surface treated
Silicon Carbide / Silicon Carbide
Viton
www.imo.se
ACG7 1123.02 GB
For handling of fluids which may be aggresive to above materials, consult IMO AB.
5. Performance Guide Typical performance values at 5 bar Flow calculated at 26 cSt, power at 260 cSt.
increase opening pressure (5) Inlet gauge. ISO G3/8 (6) Outlet gauge. ISO G3/8
Notes: - Dimensions in mm - Counter flanges according to DIN2633/ND16 - Weight is an approximate value
www.imo.se 2)
1)
Tolerances ISO h7 Tolerances ISO j6
8. Pump Dimensions
11
12
www.imo.se
ACG7 1123.02 GB
9. Pump Unit dimensions
Drawing remarks: (1) Outlet gauge. ISO G3/8 (2) Inlet gauge. ISO G3/8 (3) Control for relief valve (4) Grease nipple
ACG7 1123.02 GB
(5) Drain. ISO G1/4
(6) Deaeration (7) Space for dismantling
Notes: - Dimensions in mm - Dimensions A, A1 and AC are valid for Brook Crompton motors type WU-DA - Weight is an approximate value - Foot VDMA 24 561 PTFL
9. Pump Unit dimensions
www.imo.se
13
10. Accessories A bare shaft pump (Fig. 1) can be ordered with the accessories in fig. 2-7.
Fig. 1 Bare shaft pump
Fig. 2 Set of counter flanges
Fig. 4 Electric motor
Fig. 3 Connecting frame
Fig. 5 Shaft coupling
Fig 6. Angle bracket
Fig 7. Gauge panel
11. Maintenance and Service
14
www.imo.se
ACG7 1123.02 GB
Spare parts for these pumps are easily available from stock. For detailed information and know-how about service, see the Maintenance & Service Instruction for ACG7 pumps or contact IMO AB.
ACG7 1123.02 GB
www.imo.se
15
IMO AB: P.O. Box 42090, SE 126 14 Stockholm, Sweden. Telephone: +46 8 50 622 800
