Residential Plumbing Fixtures

April 2013
Royal Commission - Yanbu
SECTION 22 41 00
RESIDENTIAL PLUMBING FIXTURES
PART 1 - GENERAL
SCHEDULE 0 - RELATED DOCUMENTS
PRODUCT DATA SHEET 0 - Drawings and general provisions of the Contract, including
General and Supplementary Conditions and Division 01 Specification Sections, apply to
this Section.
SCHEDULE 1 - SUMMARY
PRODUCT DATA SHEET 0 - Section Includes:
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0.10
0.11
0.12
Bathtubs.
Faucets.
Lavatories.
Showers.
Kitchen sinks.
Dishwasher air-gap fittings.
Laminar-flow, faucet-spout outlets.
Disposers.
Water closets.
Toilet seats.
Supply fittings.
Waste fittings.
PRODUCT DATA SHEET 1 - Related Requirements:

1.1
1.2
1.3
1.4
1.5
Section 22 42 13.13 "Commercial Water Closets."

Section 22 42 13.16 "Commercial Urinals."
Section 22 42 16.13 "Commercial Lavatories."
Section 22 42 16.16 "Commercial Sinks."
Section 22 42 23 "Commercial Showers, Receptors, and Basins."
SCHEDULE 2 - ACTION SUBMITTALS

PRODUCT DATA SHEET 0 - Product Data: For each type of product.
0.1
0.2
22 41 00
Include construction details, material descriptions, dimensions of individual

components and profiles, and finishes for lavatories.
Include rated capacities, operating characteristics, electrical characteristics, and
furnished specialties and accessories.
PAGE 1 OF 14
Contract No: PIC-F 8128
April 2013
PRODUCT DATA SHEET 1 - Shop Drawings: Include diagrams for power, signal, and
control wiring.
SCHEDULE 3 - INFORMATIONAL SUBMITTALS
PRODUCT DATA SHEET 0 - Coordination Drawings:
mounting of counter-mounted plumbing fixtures.
Counter cutout templates for
PRODUCT DATA SHEET 1 - Sample Warranty: For special warranty.

SCHEDULE 4 - CLOSEOUT SUBMITTALS
PRODUCT DATA SHEET 0 - Operation and Maintenance Data: For plumbing fixtures
and faucets to include in emergency, operation, and operation and maintenance
manuals.
SCHEDULE 5 - MAINTENANCE MATERIAL SUBMITTALS
PRODUCT DATA SHEET 0 - Furnish extra materials that match products installed and
that are packaged with protective covering for storage and identified with labels
describing contents.
0.1
0.2
0.3
0.4
Faucet Washers and O-Rings: Equal to 10 percent of amount of each type and
size installed.
Faucet Cartridges and O-Rings: Equal to 5 percent of amount of each type and
size installed.
Flushometer-Tank Repair Kits: Equal to 5 percent of amount of each type
installed, but no fewer than two of each type.
Toilet Seats: Equal to 5 percent of amount of each type installed.
PART 2 - PRODUCTS
SCHEDULE 0 - BATHTUBS
PRODUCT DATA SHEET 0 - Bathtubs: Enameled cast iron/ Enameled steel/ FRP/PMMA,
with shower.
0.1
0.2
Manufacturers: Subject to compliance with requirements of Royal Commission.

Basis-of-Design Product: Subject to compliance with requirements.
0.3
Fixture:
22 41 00
PAGE 2 OF 14
A.
B.
C.
D.
E.
F.
0.4
0.5
0.6
0.7
A.
B.
C.
D.
April 2013
Standard:
ASME A112.19.1/CSA B45.2
for
enameled-steel
ANSI Z124.1.2 for FRP/ PMMA plastic bathtubs..
Bathing Surface: Slip resistant according to ASTM F 462.
Size: To match AR drawings.
Color: White.
Drain Location: To match AR drawings.
Drain: DN 40; chrome-plated brass, pop-up waste and overflow.
bathtubs/
Faucet: Single handle, thermostatic.

Supply Fittings: Included in faucet.
Tub Filler: Chrome-plated-brass diverter spout.
Waste Fittings:
Standard: ASME A112.18.2/CSA B45.125.2.
Drain: Stainless steel or chrome-plated brass, removable strainer.
Overflow: Chrome-plated-brass escutcheon with toggle drain-plug device.
Drain Piping: Schedule 40 PVC, DN 40 P-trap, and waste.
SCHEDULE 1 - BATHTUB FAUCETS

PRODUCT DATA SHEET 0 - NSF Standard: Comply with NSF/ANSI 61, "Drinking
Water System Components - Health Effects," for faucet materials that will be in contact
with potable water.
PRODUCT DATA SHEET 1 - Bathtub Faucets: Single handle, thermostatic.
1.1
Manufacturers: Subject to compliance with requirements.
1.2
1.3
1.4
Standards: ASME A112.18.1/CSA B125.1 and ASSE 1016.

Faucet:
A.
B.
C.
D.
E.
F.
G.
H.
I.
1.5
22 41 00
Body Material: Solid brass.

Finish: Polished chrome plate.
Maximum Flow Rate: 9.5 L/min. unless otherwise indicated.
Mounting: Exposed.
Operation: Single handle, twist or rotate control, with hot- and cold-water
indicators.
Antiscald Device: Integral with mixing valve.
Check Stops: Check-valve type, integral with or attached to body; on hot- and
cold-water supply connections.
Diverter: In-tub filler spout.
Supply Connections: DN 15.
Shower Head:
PAGE 3 OF 14
A.
B.
C.
D.
E.
F.
G.
1.6
April 2013
Standard: ASME A112.18.1/CSA B125.1.

Type: Ball joint with arm and flange.
Shower Head Material: Metallic with chrome-plated finish.
Spray Pattern: Adjustable.
Integral Volume Control: Required.
Shower-Arm, Flow-Control Fitting: 7.6 L/min.
Temperature Indicator: Integral with faucet.
Bathtub Filler Spout: Chrome-plated brass.
SCHEDULE 2 - LAVATORIES
PRODUCT DATA SHEET 0 - Lavatories: Oval /Rectangular/Round, vitreous china, counter
mounted.
0.1
0.2
0.3
A.
Fixture:
Standard: ASME A112.19.2/CSA B45.1 for vitreous-china lavatories.
Type: Self-rimming.
Oval Nominal Size: 508 by 432 mm.
Rectangular Nominal Size: 508 by 457 mm.
Round Nominal Size: 483 mm in diameter
Faucet-Hole Punching: One hole.
Faucet-Hole Location: Rim.
Color: White.
B.
C.
D.
E.
F.
G.
H.
0.4
0.5
0.6
Faucet: Two-handle mixing valve.

Supply Fittings: Comply with requirements in "Supply Fittings" Article.
Waste Fittings: Comply with requirements in "Waste Fittings" Article.
PRODUCT DATA SHEET 1 - Lavatories: Oval, vitreous china, pedestal.

1.1
1.2

1.3
Fixture:
A.
B.
C.
D.
E.
1.4
22 41 00

Oval Nominal Size: 508 by 432 mm.
Faucet-Hole Punching: One hole.
Faucet-Hole Location: Top.
Color: White.
Faucet: Two-handle mixing valve.
PAGE 4 OF 14
1.5
1.6
April 2013

Waste Fittings: Comply with requirements in "Waste Fittings" Article.
SCHEDULE 3 - LAVATORY FAUCETS

with potable water.
PRODUCT DATA SHEET 1 - Lavatory Faucets: Two-handle mixing valve.
1.1
1.2
1.3
1.4

General: Include hot- and cold-water indicators; coordinate faucet inlets with
supplies and fixture holes; coordinate outlet with spout and fixture receptor.
Body Material: General-duty, copper or brass underbody with brass cover plate.
Maximum Flow Rate: 8.3 L/min.
Centers: 102 mm Adjustable.
Mounting: Deck, exposed.
Valve Handle(s): Knob.
Inlet(s): DN 10 tubing, with DN 15 male adaptor .
Spout: Rigid.
Spout Outlet: Laminar flow Spray.
Operation: Noncompression, manual.
Drain: Stopper with chain.
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
1.14
1.15
SCHEDULE 4 - SHOWERS
PRODUCT DATA SHEET 0 - Showers: Standard PMMA/FRP with base and faucet.
0.1
0.2
0.3
Standard: ANSI Z124.1.2.

Nominal Size: 1065 by 915 mm unless otherwise indicated in AR
drawings.
Surround: One piece.
Bathing Surface: Slip resistant according to ASTM F 462.
Color: White.
Drain Location: Left side OR Right side.
Faucet: Single handle, thermostatic mixing valve.
0.4
0.5
0.6
0.7
0.8
0.9
22 41 00
PAGE 5 OF 14
April 2013
SCHEDULE 5 - SHOWER FAUCETS

with potable water.
PRODUCT DATA SHEET 1 - Shower Faucets: Single handle, thermostatic, mixing valve.
1.1
1.2
1.3
Fixture:
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
1.4
1.5
A.
B.
C.
D.
E.

General: Include hot- and cold-water indicators; check stops; and fixed shower
head, arm, and flange. Coordinate faucet inlets with supplies.
Body Material: Solid brass with nonmetallic trim.
Mounting: Exposed.
Backflow-Prevention Device for Hand-Held Shower: Required.
Operation: Noncompression, manual.
Antiscald Device: Integral with mixing valve.
Check Stops: Check-valve type, integral with or attached to body; on hot- and
cold-water supply connections.
Supply Connections: DN 15.
Shower Head:
Type: Ball joint and head integral with mounting flange.
Shower Head Material: Metallic with chrome-plated finish.
Spray Pattern: Adjustable.
Integral Volume Control: Not required.
Shower-Arm, Flow-Control Fitting: 7.6 L/min.
SCHEDULE 6 - KITCHEN SINKS

PRODUCT DATA SHEET 0 - Kitchen Sinks: Two bowl, counter mounted, stainless steel.
0.1
0.2
Basis-of-Design Product: Subject to compliance with requirements of Royal

Commission.
0.3
A.
Fixture:
Standard: ASME A112.19.3/CSA B45.4 for stainless-steel kitchen sinks.
22 41 00
PAGE 6 OF 14
B.
C.
D.
Dimensions: 16x14x9 or 407x356x230 mm depth.

Drain: 89-mm crumb cup.
a.

a.

a.
0.5
0.6
A.
B.
Location: Near back of bowl.
Right Bowl:
1.
2.
0.4
Left Bowl:
1.
2.
F.
April 2013
Overall Dimensions: 54x18 or 1372 by 457 mm.

Metal Thickness: 1.3 mm.
Bowl:
1.
2.
E.
Faucet: Solid brass Kitchen Sink Faucet.

Waste Fittings: Comply with requirements in "Waste Fittings" Article, except
include continuous waste for multibowl sinks.
Disposer: Continuous-feed house hold food waste Disposers.
Dishwasher Air-Gap Fitting: Comply with requirements in "Dishwasher Air-Gap
Fittings" Article.
SCHEDULE 7 - SINK FAUCETS

with potable water.
PRODUCT DATA SHEET 1 - Sink Faucets: Solid brass, kitchen sink faucet.
1.1
1.2
1.3
1.4

General: Include hot- and cold-water indicators; coordinate faucet inlets with
supplies and fixture holes; coordinate outlet with spout and fixture receptor.
1.5
22 41 00
PAGE 7 OF 14
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
April 2013

Mixing Valve: Two-lever handle.
Centers: 102 mm Adjustable.
Mounting: Deck, exposed.
Handle(s): Knob.
Spout Type: Swivel gooseneck.
Spout Outlet: Laminar flow.
Drain: Stopper with chain.
SCHEDULE 8 - DISHWASHER AIR-GAP FITTINGS

PRODUCT DATA SHEET 0 - Dishwasher Air-Gap Fittings:
0.1
0.2

0.3
0.4
Standard: ASSE 1021.

Description: Device designed to prevent backflow of contaminated liquid into
domestic dishwashers.
Material: Plastic body with chrome-plated-brass cover.
Hose Connections: 16-mm- ID inlet and 22-mm- ID outlet.
Capacity: At least 0.32 L/s; at inlet pressure of at least 35 kPa and at
temperature of at least 60 deg C.
Mounting: Deck.
Hoses: Rubber and suitable for temperature of at least 60 deg C.
0.5
0.6
0.7
0.8
0.9
A.
B.
Inlet Hose: 16 mm ID and 1219 mm long.

Outlet Hose: 22 mm ID and 1219 mm long.
SCHEDULE 9 - LAMINAR-FLOW, FAUCET-SPOUT OUTLETS

Water System Components - Health Effects," for faucet-spout outlet materials that will
be in contact with potable water.
PRODUCT DATA SHEET 1 - Manufacturers: Subject to compliance with requirements.
PRODUCT DATA SHEET 2 - Basis-of-Design
Product:
Subject to compliance with
requirements.
PRODUCT DATA SHEET 3 - Description: Chrome-plated-brass, faucet-spout outlet that
produces non-aerating, laminar stream. Include external or internal thread that mates
with faucet outlet for attachment to faucets where indicated and flow-rate range that
includes flow of faucet.
22 41 00
PAGE 8 OF 14
April 2013
SCHEDULE 10 - DISPOSERS
PRODUCT DATA SHEET 0 - Disposers: Continuous-feed household, food waste.
0.1
0.2
0.3
Standards: ASSE 1008 and UL 430, and listed and labeled as defined in
NFPA 70, by a qualified testing agency, and marked for intended location and
application.
General: Include reset button; wall switch; corrosion-resistant chamber with
jam-resistant, cutlery- or stainless-steel grinder or shredder; DN 40 outlet;
quick-mounting, stainless-steel sink flange; antisplash guard; and combination
cover/stopper.
Model: Sound-insulated chamber and stainless-steel outer shell.
Motor: 230-V ac, 1725 rpm, 3/4 hp with overload protection.
0.4
0.5
0.6
SCHEDULE 11 - WATER CLOSETS

PRODUCT DATA SHEET 0 - Water Closets:
Floor mounted, floor outlet, close coupled

(gravity tank/flushometer tank), vitreous china.
0.1
0.2
0.3
Bowl:
A.
B.
C.
D.
E.
F.
0.4
0.5
A.
B.
C.
Standards: ASME A112.19.2/CSA B45.1, ASME A112.19.5, and ASSE 1037.

Bowl Type: Siphon jet.
Height: Standard.
Rim Contour: Regular.
Water Consumption: Water saving.
Color: White.
Toilet Seat: Refer to Toilet Seats Article.
Supply Fittings:
Supply Piping:
Chrome-plated-brass pipe or chrome-plated-copper tube
matching water-supply piping size. Include chrome-plated wall flange.
Stop: Chrome-plated-brass, one-quarter-turn, ball-type or compression stop
with inlet connection matching water-supply piping type and size.
1.
22 41 00
Operation: Wheel handle.
PAGE 9 OF 14
D.
April 2013
Riser:
1.
2.
Size: DN 15.
Material: ASME A112.18.6, braided- or corrugated-stainless-steel flexible
hose riser.
SCHEDULE 12 - TOILET SEATS

PRODUCT DATA SHEET 0 - Toilet Seats :
0.1
0.2
0.3
0.4
Standard: IAPMO/ANSI Z124.5.

Material: Plastic.
Type: Residential (Standard).
Shape: Regular rim (Closed front).
Configuration: Closed front with cover.
Size: Regular.
Hinge Type: Self-sustaining, check.
Hinge Material: Plastic.
Seat Cover: Required.
Color: White.
0.5
0.6
0.7
0.8
0.9
0.10
0.11
0.12
SCHEDULE 13 - SUPPLY FITTINGS

with potable water.
PRODUCT DATA SHEET 1 - Standard: ASME A112.18.1/CSA B125.1.
PRODUCT DATA SHEET 2 - Lavatory and Kitchen Sink Supply Fittings:
2.1
2.2
A.
2.3
A.
B.
22 41 00
Supply Piping:
Chrome-plated-brass pipe or chrome-plated-copper tube
matching water-supply piping size. Include chrome-plated wall flange.
Stops: Chrome-plated-brass, one-quarter-turn, ball-type or compression stop
with inlet connection matching water-supply piping type and size.
Operation: Wheel handle.
Risers:
Size: DN 10 for lavatories.
Size: DN 15 for kitchen sinks.
PAGE 10 OF 14
C.
April 2013
Material: ASME A112.18.6, braided- or corrugated-stainless-steel flexible hose

riser.
SCHEDULE 14 - WASTE FITTINGS

PRODUCT DATA SHEET 0 - Standard: ASME A112.18.2/CSA B125.2.
PRODUCT DATA SHEET 1 - Drain:
Grid type with DN 32 offset tailpiece for accessible
lavatories.
PRODUCT DATA SHEET 2 - Drain:
Grid type with DN 40 offset tailpiece for accessible
kitchen sinks.
PRODUCT DATA SHEET 3 - Trap:
3.1
3.2
3.3
Size: DN 40 by DN 32 for lavatories.

Size: DN 40 for kitchen sinks.
Material: ASTM F 409 ABS or PVC two-piece trap and waste to wall and wall
flange.
SCHEDULE 15 - GROUT
PRODUCT DATA SHEET 0 - Standard:
ASTM C 1107/C 1107M,
hardening and volume-adjusting, dry, hydraulic-cement grout.
Grade B,
post-
PRODUCT DATA SHEET 1 - Characteristics: Nonshrink; recommended for interior and

exterior applications.
PRODUCT DATA SHEET 2 - Design Mix: 34.5-MPa, 28-day compressive strength.
PRODUCT DATA SHEET 3 - Packaging: Premixed and factory packaged.

PART 3 - EXECUTION
SCHEDULE 0 - EXAMINATION
PRODUCT DATA SHEET 0 - Examine roughing-in of water-supply and sanitary
drainage and vent piping systems to verify actual locations of piping connections before
plumbing-fixture installation.
PRODUCT DATA SHEET 1 - Examine walls, floors, cabinets, and counters for suitable
conditions where fixtures will be installed.
PRODUCT DATA SHEET 2 - Proceed
conditions have been corrected.
22 41 00
with
installation
PAGE 11 OF 14
only
after
unsatisfactory
April 2013
SCHEDULE 1 - INSTALLATION
PRODUCT DATA SHEET 0 - Install plumbing fixtures level and plumb according to
roughing-in drawings.
PRODUCT DATA SHEET 1 - Install floor-mounted water closets on closet flange
attachments to drainage piping.
PRODUCT DATA SHEET 2 - Install counter-mounting fixtures in and attached to
casework.
PRODUCT DATA SHEET 3 - Install pedestal lavatories on pedestals and secured to
wood blocking in wall.
PRODUCT DATA SHEET 4 - Install water-supply piping with stop on each supply to
each fixture to be connected to water distribution piping. Attach supplies to supports or
substrate within pipe spaces behind fixtures. Install stops in locations where they can
be easily reached for operation.
4.1
Exception: Use ball, gate, or globe valves if supply stops are not specified with
fixture. Comply with valve requirements specified in Section 22 05 23 "GeneralDuty Valves for Plumbing Piping."
PRODUCT DATA SHEET 5 - Install tanks for accessible, tank-type water closets with
lever handle mounted on wide side of compartment.
PRODUCT DATA SHEET 6 - Install toilet seats on water closets.
PRODUCT DATA SHEET 7 - Install faucet flow-control fittings with specified flow rates
and patterns in faucet spouts if faucets are not available with required rates and
patterns. Include adapters if required.
PRODUCT DATA SHEET 8 - Install shower flow-control fittings with specified maximum
flow rates in shower arms.
PRODUCT DATA SHEET 9 - Install traps on fixture outlets.
9.1
9.2
Exception: Omit trap on fixtures with integral traps.

Exception: Omit trap on indirect wastes unless otherwise indicated.
PRODUCT DATA SHEET 10 - Install disposer in outlet of each sink indicated to have a
disposer. Install switch where indicated or in wall adjacent to sink if location is not
indicated.
PRODUCT DATA SHEET 11 - Install dishwasher air-gap fitting at each sink indicated to
have air-gap fitting. Install in sink deck. Connect inlet hose to dishwasher and outlet
hose to disposer.
22 41 00
PAGE 12 OF 14
April 2013
PRODUCT DATA SHEET 12 - Install hot-water dispensers in back top surface of sink or
in countertop with spout over sink.
PRODUCT DATA SHEET 13 - Set bathtubs and shower receptors in leveling bed of cement
grout.
PRODUCT DATA SHEET 14 - Install protective shielding pipe covers and enclosures on
exposed supplies and waste piping of accessible lavatories and sinks. Comply with
requirements in Section 22 07 19 "Plumbing Piping Insulation."
PRODUCT DATA SHEET 15 - Install wall flanges or escutcheons at piping wall penetrations
in exposed, finished locations. Use deep-pattern escutcheons if required to conceal

protruding fittings. Comply with escutcheon requirements specified in Section 22 05 18
"Escutcheons for Plumbing Piping."
PRODUCT DATA SHEET 16 - Seal joints between plumbing fixtures, counters, floors, and
walls using sanitary-type, one-part, mildew-resistant silicone sealant. Match sealant

color to fixture color. Comply with sealant requirements specified in Section 07 92 00
"Joint Sealants."
SCHEDULE 2 - CONNECTIONS
PRODUCT DATA SHEET 0 - Connect fixtures with water supplies, stops, and risers,
and with traps, soil, waste, and vent piping. Use size fittings required to match fixtures.
PRODUCT DATA SHEET 1 - Comply
with water
Section 22 11 16 "Domestic Water Piping."
piping
requirements
specified
in
PRODUCT DATA SHEET 2 - Comply with soil and waste piping requirements specified in
Section 22 13 16 "Sanitary Waste and Vent Piping."

PRODUCT DATA SHEET 3 - Install protective shielding pipe covers and enclosures on
exposed supplies and waste piping of accessible lavatories and sinks. Comply with
requirements in Section 22 07 19 "Plumbing Piping Insulation."
SCHEDULE 3 - ADJUSTING
PRODUCT DATA SHEET 0 - Operate and adjust plumbing fixtures and controls.
Replace damaged and malfunctioning fixtures, fittings, and controls.
PRODUCT DATA SHEET 1 - Adjust water pressure at faucets to produce proper flow.
SCHEDULE 4 - CLEANING AND PROTECTION
PRODUCT DATA SHEET 0 - After completing installation of plumbing fixtures, inspect and
repair damaged finishes.

22 41 00
PAGE 13 OF 14
April 2013
PRODUCT DATA SHEET 1 - Clean plumbing fixtures, faucets, and other fittings with
manufacturers' recommended cleaning methods and materials.
PRODUCT DATA SHEET 2 - Provide protective covering for installed plumbing fixtures
and fittings.
PRODUCT DATA SHEET 3 - Do not allow use of plumbing fixtures for temporary facilities
unless approved in writing by Royal Commission.

END OF SECTION 22 41 00
22 41 00
PAGE 14 OF 14

Residential Plumbing Fixtures

Uploaded by

Copyright:

Available Formats

Residential Plumbing Fixtures

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Residential Plumbing Fixtures

Uploaded by

Copyright:

Available Formats

April 2013

Royal Commission - Yanbu

PRODUCT DATA SHEET 1 - Related Requirements:

Section 22 42 13.13 "Commercial Water Closets."

SCHEDULE 2 - ACTION SUBMITTALS

Include construction details, material descriptions, dimensions of individual

Contract No: PIC-F 8128

Royal Commission - Yanbu