Probationary Firefighters Manual

Probationary Firefighters Manual
Chapter 17
EMERGENCIES
To make members aware of the nature of the most commonly

responded to emergencies.
To instruct members on how the FDNY handles those emergencies
the care and maintenance of fire hydrants
Water Conditions
Steam Conditions
Electrical Emergencies
Natural Gas Emergencies
Oil Burner Emergencies
Vehicular Accidents
Subway Emergencies
Miscellaneous Emergencies
SOURCE:
FDNY All Unit Circulars

FDNY Training Bulletins
FDNY REFERENCE:
A.U.C. 207
TB Emergencies 2,3
OBJECTIVE:
CONTENTS:
17
EMERGENCIES
Section
Title
Page
WATER CONDITIONS ....................................................... 1
STEAM CONDITIONS ....................................................... 9
ELECTRICAL EMERGENCIES............................................ 10
NATURAL GAS EMERGENCIES ........................................ 13
OIL BURNER EMERGENCIES ........................................... 17
VEHICULAR ACCIDENTS ................................................. 18
SUBWAY EMERGENCIES .................................................. 20
MISCELLANEOUS EMERGENCIES .................................... 38
CONCLUSION .................................................................. 41
FDNY
Chapter Seventeen
EMERGENCIES
ost of us, before we became firefighters thought that the Fire Department responded only
to fires. In reality we are present at every type of emergency situation that occurs in New
York City. These responses account for 21% or our turnouts- and in recent years 38% of
the work we do is of an emergency nature. The percent of people saved at emergencies from injury,
death, discomfort and even fire is probably higher than those aided at fires.
The Fire Department does not advertise but the public relies on us to solve any problems they feel
are dangerous to themselves, their families or property. Firefighters react to this with the
knowledge that often at inconvenient times, in inclement weather and without any thanks we are
professionals capable of remedying any solution. To enhance this ability we continue to study
those problems we may encounter.
1.
WATER CONDITIONS
1.1
GENERAL OPERATIONS
Determine the source of the leak and locate the corresponding water shut off
valve. Locate water shut-off: Possible shut-off locations include:
on the wall near the ceiling of the apartment directly below.
on riser line of apartments in basements.
Still no shut off; then locate where main enters building. Usually near
front building wall. (Often in a corner.)
Pipe is coldest pipe in building and may also have condensation on outside
Listen for sound of running water.
Feel vibration.
Armored ground cable may be attached to main from electric meter.
Once valve is located, shut off clockwise.
If water has leaked into an electrical fixture, turn off power at the fuse box or
circuit breaker.
1.2
WATER CONDITIONS: WATER LEAKS

Toilet Bowl Leaking.
It is 3 a.m. and your unit is called to an apartment where water is leaking into a
light fixture from the apartment above . We may have to disconnect the light
fixture or pull the fuse as well as shutting off the water.
Possible action to stop leak.
Depends on type but generally if the ball in the water tank can be raised
it will stop flow.
Sometimes under the tank a shut off handle is situated. Turn clockwise.
Flushometer Stuck:
Possible action:
Shake handle.
1
FDNY
Chapter Seventeen

EMERGENCIES
Tighten large fitting which is either serrated on edge or hexagonal in
shape. Often they can be sufficiently tightened by hand to stop flow.
This fitting is in supply elbow.
Tap with flat head of axe gently. This may reset valve in flushometer
body.
Leaking Sinks.
Possible actions:
Locate handle under sink.
Turn clockwise.
FDNY
Chapter Seventeen

EMERGENCIES
Broken Pipe or Leaking Pipe.
Possible actions:
If shut off handle is accessible turn clockwise.
If inaccessible and tubing used then simply crimp until flow stops.
(Use pliers, tap with axe, etc.).

For non malleable metal use tapered piece of wood (shaved chock,
pencil, chair leg, golf tee, etc.
An emergency patch on a pipe can be made with a piece of rubber inner

tube and held with duct tape, rubber tape, clamp or coat hanger wire,
etc..
A screw plug can be used with a rubber gasket on pipes or water tanks.
The packing nut may need tightening in a clockwise direction. Do not
overturn.
House Main.
Frequently broken by scavengers collecting mungo for resale.
Action must be taken to stop water flow.
Malleable pipe (copper, lead): Strike with maul or flat head of axe until
sufficiently closed to stop water flow.
FDNY
Chapter Seventeen

EMERGENCIES
Not Malleable: Insert rounded end of stick, chock, pencil, chairleg, etc.
to be used as a plug.
NOTE: It is sometimes helpful to use cloth on end of wood to aid in
sealing.
FDNY
Chapter Seventeen
EMERGENCIES
1.3
WATER CONDITIONS: FLOODED BASEMENTS
Occupied building.
May cause problems with oil burner in building or in an adjoining

building. Children may be playing in area and could possibly be
drowned.
Actions to be taken:
o If location of drain is known then clear surrounding area of debris
and if possible channel flow towards drain. Look near shower or
basement sink for drain if location of drain is unknown.
o Remove the toilet bowl. This action will provide drainage. A

screen or wire basket will keep out debris.
Vacant building.
Same actions as occupied building
Break into cast iron waste pipe at most convenient location with Halligan
and axe to permit water to escape. This location can be at ceiling level
depending on water depth.
Remove clean - out plug of waste pipe.
Open the street trap on the sewer side.
.
CAUTION
Avoid areas of basements where electrical power may be on.
FDNY
Chapter Seventeen
1.4

EMERGENCIES
WATERCONDITION: Flooded Roofs

DO NOT CLEAR ANY BLOCKAGE WITH HANDS!!! Member's arm

can be drawn into drain. Deaths have resulted. Actual suction pressure
can be quite high.
Clear blockage with 6' hook or applicable tool from drain or scupper.
Using hose.
o Stretch entire length under water and allow to fill.
o Kink one end.
o Drape edge over parapet extending below roof level.
o Release kink.
Bring booster line to roof.

o Charge line and open nozzle.
o Place under water.
o Shut down pumps and disconnect line at street.
o Allow to drain.
FDNY
Chapter Seventeen

EMERGENCIES
Alternate possibility: remove a brick at a low point on a parapet wall which will serve as a
scupper.
Each sq. ft. over 12" deep weighs 62 pounds. Use as few members as practical on the roof.
FDNY
Chapter Seventeen
1.5

EMERGENCIES
WATER CONDITION: OPEN HYDRANT
Hydrant shut down.

Action : Operating Nut
Turn operating nut counter clockwise.
Avoid contact with other metal objects when operating hydrants that are
close to trouble in underground electrical services, or, when possible,
avoid using hydrants close to trouble in underground electric services.
Street shut down.

Action:
Remove plate (sometimes difficult).
After cover removed, you may have to direct some water to clear
chamber of mud and debris.
Place wrench on fitting (this is not always easily done) and turn counter
clockwise 17 times.
NOTES:
1.
To facilitate operation water may have to be diverted by board,

garbage can cover, etc.
2.
Not until about 12 full turns is there a noticeable decrease in flow.
3.
Nut is usually found off center on the street side of the chamber.
FDNY
Chapter Seventeen
2.

EMERGENCIES
STEAM CONDITIONS
2.1
Radiator
Safety Valve blown off
Action:
Shut down flow at the valve handle by turning clockwise
Replace safety valve or plug with a wooden plug wrapped in cloth, tapping it in
until secure.
RADIATOR & VALVES

2.2
Flow valve blown off.

This is usually due to numerous operations of on and off flow. Generally it will be
nearby and undamaged.
Action:
Make certain flow handle is in open position (this is important).
Replace fitting to open piping by turning nut on in clockwise direction.
After restoration of flow valve it may be turned off or on as necessary. The use
of a compound or sealant on threads may be beneficial in obtaining a seal.
Crayon, string, cotton thread or wax may be used.
NOTES:
1.
Wear gloves.
2.
3.
Place towel over main valve to divert steam flow while resetting
valve.
It may be necessary to shut steam off at boiler.
FDNY
Chapter Seventeen
3.

EMERGENCIES
ELECTRICAL EMERGENCIES
3.1
OVERHEAD ELECTRICAL SERVICE EMERGENCIES

When live electrical wires fall, they constitute a hazard to the public as well as
responding firefighters. It is essential for the Officer of the responding unit to make
a careful assessment of the risk to both civilians and members.
All Fire Department units are to treat downed wires as live wires until an on scene
utility company representative confirms that the wires have been de-energized.
There is currently no safe way for FDNY personnel to move energized power lines,
even if it presents a condition imminently dangerous to life.
Members shall not take any actions relating to removing electrical wires from
people and/or vehicles until wires are de-energized by the utility company.
Do not attempt to remove occupants from vehicles in contact with wires until wires
are de-energized by the utility company.
Do not attempt to move wires with any hook or rope.
3.2
WIRES DOWN IN THE STREET

3.2.1 Immediately upon confirming that live electrical wires are down and are
creating a situation that places life in danger:
3.2.1.1 The first arriving unit must contact the Fire Department Dispatcher
via Department radio indicating that life is in danger. Specify the
location (address, pole number) of the downed wires, and request
forthwith power removal and priority response by utility company.
3.2.1.2 Request response of Battalion Chief if not already assigned.
3.2.1.3
Responding Battalion Chief shall also contact the Utility Company

Electrical Operations Center directly by cell phone indicating that
life is in danger and request priority response. These telephone
numbers are found on the Con Edison notification cards distributed
to all Chiefs Officers.
3.2.2 In situations involving live electrical wires, which are down but do
not present an imminent life hazard, the Department can only guard against
the hazards of fallen wires by isolating the area, notifying the utility
company, and standing by until a utility company crew responds. It is the
utility company that will correct the problem.
In either of the situations listed above, the following actions shall be
taken:
Immediate notification to the dispatcher/utility for priority utility company
response.
Isolate the area.
10
FDNY
Chapter Seventeen

EMERGENCIES
Keep apparatus away. Overhead wires are supported by poles,
which could possibly topple in a domino effect, thereby
endangering members if they are within the area of possible
pole collapse.
Check nearby buildings for heat at fuse box/electrical service entrance
box. Utilize thermal imaging cameras as hand contact may result in
electrocution if the box is energized.
Caution civilians trapped in vehicles with an electrical line over it to
remain in their vehicle until the wires are de-energized by the utility
company.
Stretch line with fog nozzle. Use distance as a safety factor. Keep at least
25 feet away from any downed wire while operating this handline.
The following are additional guidelines for the safety of all members:
Fallen or hanging wires are not to be moved by members.
Avoid metal gratings, manholes, fences, puddles, wet grass, etc.
Highly energized wires often whip and snap while producing sparks.
The ground immediately near a fallen wire may be energized (voltage
gradient) causing injury or death to anyone approaching the downed wire.
Do not place weighted objects on downed wires. This may cause the wire
to make substantial contact with the ground and produce arcing and
whipping as well as produce a voltage gradient in the immediate area.
Do not open the house service. Heated wires may generate carbon
monoxide gas in the service box, which can explode when the opening of
a breaker creates a spark.
3.3
POWER STATION / SUBSTATION EMERGENCY:
ACTIONS TO BE TAKEN:
Place a priority call to the Fire Department dispatcher for power removal.
Be sure to request that ALL electrical equipment at the station be deactivated
and request the immediate on site response of a utility company representative.
All electrical equipment at the station/substation is to be considered energized
until verification of power removal is made by the on site utility company
personnel.
11
FDNY
Chapter Seventeen

EMERGENCIES
Unless human life is in jeopardy, do not enter substation until arrival of
power company representative.
Do not under any circumstances bring metal ladders or metal tools inside
of gate of generating station.
Do not enter fenced off areas without power company representative.
No ladders, metal or wood, should be supported by metal

superstructures.
NOTE:
3.4
The metal overhead piping in a substation or rectified station

are "bus bars" and carry high voltage and/or amperage. These
may arc up to 18 feet.
OVERHEATED BALLAST:
Flourescents:
How to identify.
Smoke emanating from fixture.
Smell
Flickering light.
Partial or complete darkening of bulb.
Presence of heat.
Shut off power.
Remove bulb.
Remove cover panel.
Disconnect wires to ballast (black box) and remove same.
Isolate black and white power wires and cover exposed ends with caps or
tape. Keep apart.
Check for any fire or smoldering in ceiling.
Overheated fluorescent ballasts may leak PCB-contaminated oil. SCBA

must be used while performing the above operations.
12
FDNY
Chapter Seventeen
4.

EMERGENCIES
NATURAL GAS EMERGENCIES

4.1
General precautions:
Gas leaks are a common emergency in New York City. When called to a gas leak
take the following precautions:
Confirm the nature of the gas leak: is it natural gas, propane, or gasoline?
Extinguish all sources of ignition.
Ventilate the area if necessary. Be aware that if the gas/air mixture in the room
is too rich to burn, it will pass through its flammable/explosive range as you
ventilate.
Shut off the gas supply
If the gas leak is at an appliance, the gas feed to the appliance should be shut off.
If that is not possible or the leak is elsewhere, then the gas supply to the
apartment or building must be shut down.
13
FDNY
Chapter Seventeen
4.2
Points of control to stop the leak:

EMERGENCIES
Gas Meter Valves - Meter Wing Cock
Using the gas meter as a starting point and working toward source of supply
side, the first point of control is the meter wing cock. This valve is located
just outside the meter on the piping.
When in the ON position, the wing of the cock runs parallel to the piping.
To shut the gas at the meter, turn the key so its at a right angle to the pipe.
The key can be turned with pliers or the fork end of a hand tool.
Main Shut Off Valves: The next point of control, from the meter toward the
supply, is a service shut-off at the point service enters into the building. This
valve should be located just inside the building wall and may vary in design and
method of operation.
Curb Valve:
The third shut off location, moving toward the supply point, is the Curb
Valve. This is the service shut off located outside the building. The works
Curb Valve is a misnomer. Its original location was just inside the curb
line. However, most curb valves are located approximately 18 on the
14
FDNY
Chapter Seventeen

EMERGENCIES
sidewalk side of the curb, whether or not there is a grass plot in the
immediate area of not.
To operate the valve break the concrete covers remove the pieces and the
wooden shelf, and use the gas key which has been supplied to the various
units.
To operate the valve break the concrete covers remove the pieces and the wooden shelf, and use the
gas key which has been snpplied to the various units.
IMPORTANT: When Fire Department personnel shut off a utility, or find a utility shut, they are
not to turn the utility back on! The utility company must be notified to restore service.
15
FDNY
Chapter Seventeen
4.3

EMERGENCIES
Gas Leak Kitchen Stove:

Check that stove is not on.
If stove off then locate butterfly on piping or tubing at rear. Turn until butterfly
is perpendicular to flow of gas pipe ( turn.)
Occupant needs utility company check stove and restore gas.
NOTE:
4.4
A liquid detergent brushed on area of suspected leak will bubble if

gas is leaking.
Gas Leak In Ceiling Around Light Fixture:

Causes:
Usually occurs as the result of the occupant removing the plug in the old
gas supply line when installing a new fixture.
It can also occur because repairmen only used wax as a plug when gas
line use was discontinued, and this wax either melts or deteriorates over
a long period of time causing a leak.
Possible actions:
Make certain area is ventilated.
If he has removed cap then replace same. If he has sawed into pipe then
shut off at service to apartment which may be in the apartment or in
basement.
NOTE: Service entrance is where gas, electric and water enter
building.
Occupant requires Brooklyn Union Gas or Con Ed to restore gas. Under

no circumstances should units restore service as there may be open pilots
or burners on elsewhere.
WARNING:
Gas piping is of small diameter and there is a possibility of it being

energized through faulty electrical connections. i.e., Someone may be
inadvertently using pipe as a ground.
4.5
Gas Boiler Residential

Identification metallic odor caused by overheating when aquastat or low water
cut-off is not functioning. Sides of boiler can be cherry red. Boiler needs water.
DO NOT ADD. The boiler must cool down first.
16
FDNY
Chapter Seventeen
5.

EMERGENCIES
Locate gas shutoff at either boiler or at service entrance. Turn perpendicular
to piping (1/4 turn)
Occupant needs Brooklyn Union Gas or Con Ed to restore gas
OIL BURNER EMERGENCIES:

Often on arrival you have a heavy odor or visible smoke on scene which is usually caused
by delayed ignition.
5.1
Methods of disconnecting electric power:

Shut off electric power by use of oil burner remote control. Oil burner remote
control is generally painted red and generally located at the following locations:
In a private dwelling at the top of interior cellar stairs.
In an old law tenement, brownstone or frame building at the top of the

interior cellar stairs.
NOTE: At above locations listen for sound of burner going off as switch
may be for lights.
In a new law tenement or apartment house outside of the oil burner
room.
NOTES:
1.
2.
Be alert to other locations for switch especially if there is a

commercial occupancy on street floor.
It is helpful to turn on lights if possible.
Fuse box.
Remove fuse.
Pull knife switch.
Switch off circuit breaker.

NOTE: Box is usually marked "oil burner." Power line can also be traced
from oil burner or switch.
5.2
Ignition component at boiler: Remove cover from component and place

non-conductor between contact points. (Small piece of wood, plastic,
rubber, cardboard, etc.
Fuel shut off:

At tank (all tanks have shut off).
At oil burner (with 275 gallon tanks).
On preheat or #6 oil, turn gas of to preheater (1/4 turn) and also the electric.
17
FDNY
Chapter Seventeen
EMERGENCIES
On boilers with larger than 275 gallon tanks there may be a shut off on the feed
line near the filter.
Caution: There is a very real danger of the flexible, thin wall gas line tubing to
the preheater melting or being disconnected. The gas/air mixture ignited by the
heat of the oil burner can result in an explosion in which members have been
injured.
6.
VEHICULAR ACCIDENTS:
Actions to be taken.
6.1
Rope off and clear area.
6.2
Chock vehicle.
6.3
Keep apparatus out of immediate area.
6.4.
Stretch and charge a line into position to protect a trapped victim.
6.5.
If gasoline is leaking then battery should be disconnected, ground cable first. At

times, hoods, batteries and trunks are destroyed for no viable reason. Try to locate
key.
Hydrogen is evolved when electric storage batteries are being charged. When a
firefighter attempts to disconnect a battery with a large metal tool he can
accidentally short the two terminals. The resulting sparks can ignite the
hydrogen in the battery causing it to blow apart.
Shorting terminals is not the only way to produce a spark. Connecting or
disconnecting terminals can also create sparks. Turning off all current drawing
devices in the vehicle before disconnecting the battery will eliminate sparking.
It would also be safer to disconnect the grounded terminal first and to use a tool
small enough to avoid accidental contact across the battery terminals.
Note: Some cars have two batteries (Diesels) and some have battery in trunk.
6.6
Prevent movement of vehicle if victim is trapped.
6.7
Do not forcefully pull victim free as it may aggravate the injury. An examination for
bleeding and fractures should be made.
6.8
Prevent smoking at scene if gasoline is leaking or oxygen being used.
6.9
Request police for traffic and crowd control and EMS if services are required.
6.10
Special units can be called for their use of emergency equipment (Saws, Hurst Type
Tool, etc.).
18
FDNY
Chapter Seventeen

EMERGENCIES
Catalytic converters can reach 2000 F, well above the ignition temperature of
leaves, grass, etc.. This must be considered when working near overturned vehicles
or using air bags. These high temperatures can cause severe burns and/or damage
air bags.
Note: If vehicle is to be towed, use a chain. A cable will store kinetic energy
and if cable snaps serious injuries can occur. If a link snaps there is no
violent whipping action.
6.11
If necessary to open car door consider the following:

Try to obtain key.
Use coat hanger to raise lock button or door handle.
Use a "slim jim" (slim jim to be used only in emergency and is used as follows:)
Insert tool between glass and door panel.
Depending on make of car we either pull up with hook end or push down
with slot end on activating arm or rod to release lock.
NOTES:
1.
2.
Aim for lock area

This tool requires practice and knowledge of the location of locks on
different cars. When used properly it saves much unnecessary
damage. Some cars can be opened quicker than with a key.
19
FDNY
Chapter Seventeen
7.

EMERGENCIES
SUBWAY EMERGENCIES:
This Department on many occasions will be called upon to operate in the track areas of
numerous subway and railroad systems that serve all areas of the City Fires and
emergencies will occur on the elevated portions, in open cuts, in tunnels or stations. There
are general hazard prevalent in all systems, and some hazards peculiar to the particular
system.
Fire Department personnel will never be permitted to operate on track areas unless assured
that the power is off. This rule may be ignored only if life is in imminent peril and direct
and immediate action is required to save life. In the latter instance every possible precaution
should be taken to minimize the risk.
Types of Incidents:
Fire in Station
Fire on Track
Fire in Car
Emergencies Medical
Fire Related (Smoke-Panic)
Unit Operations
When conditions do not require power removal, reconnaissance may be
conducted by an Officers and a firefighter operating as a team and only from
platforms or catwalks. Tracks shall not be entered or crossed.
Engine Companies shall not connect to a hydrant until the fire is located.
Many operations will require more than one engine company due to long
stretches. All efforts will be concentrated on stretching and placing in operation
the initial line before back up lines are ordered.
Whenever possible, small railroad tie involving ties of an elevated railroad shall
be handled by handlines operated from the street below.
Most fires in a station are of a minor nature, e.g. rubbish fire in trash receptacle,
papers on railroad ties, or overheated ballast at station lights. These fires will
usually be controlled by a can.
When a fire is located under the platform, members will not be permitted in
track area unless:
Power is removed.
Confirmation of power removal by F.D. Dispatcher.
Members are posted at each end of platform to act as safety people.
An alternate area of refuge is assured in case of train movement.
20
FDNY
Chapter Seventeen

EMERGENCIES
7.1 Handie-Talkie Subway Relay

Handi-Talkie Relay: In underground areas, handi-talkie communication with the surface
will be adversely affected. A relay system shall be set up to overcome this. Handi-talkie
communications are poor from level to level. Communications in a straight line are from
fair to poor. Some subway stations have multiple levels underground, which will require
additional handi-talkies. The objective is to keep radios within range of each other to be
able to communicate to grade level. An engine and truck can set up a relay with 2 to 6
members. The members who are part of the communications relay must maintain their
position throughout the operation until relieved by the Incident Commander.
Truck Chauffeur
Outside Vent FF
Bottom of subway entrance stairs. If the token clerk booth is within 50

yards of stairs to street, contact train dispatcher through the clerk. (There
is a telephone in the token clerks booth. Try to obtain additional
information for the Company Officer and Incident Commander). The
LCC should relay the token booth phone number to the Truck Officer in
case it is necessary to call the booth from a blue light telephone.
The foot of the stairs leading to the platform if it is within 50 yards of
the Chauffeur.
Roof FF
Approximately 50 yards from the stairs on the platform for relay. Engine
Officer
Approximately 100 yards (line of sight) from Roof FF on the platform.
Truck Officer
To location of the fire.
Additional HT equipped members every 100 yards, if necessary.

7.2 Colored Light Globes in Subway Entrances
New York City Transit Authority has installed colored light gloves in the post
lights at street entrances. The colored globes indicate entrance availability.
There are two globe colors being used in these entrances:
GREEN Post Light: The stairway is open 24 hours a day. There will either
be a token booth clerk on duty or the station will high entry/exit turnstiles
(HEET see photo 1& 1a) with an adjacent gate secured with an FDNY 1620
lock.
RED Post Light: Token booth clerk may NOT be on duty and the stairway
may be closed some time during a 24 hour day.
If given a choice, the first point of access to a subway should be through an

entrance with a green globe, if possible.
A new replacement globe installed is a spilt type-the top half color denotes
the type of access and the bottom half is clear for better lighting of the
subway entrance.
21
FDNY
Chapter Seventeen

EMERGENCIES
Photo 1
7.3
Photo 1a
Subway Emergency Exit Key:
All companies are issued Subway Emergency Keys. There are three different key
shapes and a pry bar on this tool. All the Subway lines (IND, BMT, IRT)
emergency exits can be opened with this one key. The pry bar end is used to lift the
emergency exit door, and to scrape out debris between the door and the door buck.
However, some emergency exit locks are now appearing with other than the
standard shapes. If this is the case, a pair of vise-grips or pliers will have to be used
to open the emergency door.
22
FDNY
Chapter Seventeen

EMERGENCIES
7.4 SAFETY CONSIDERATIONS

Officers shall insure that members use extreme caution, whenever operating in the track
area. There are many potential dangers located throughout the subway system, that pose
many tripping, slipping, and falling hazards, such as grates in the track roadbed, grease,
oil, water, steeldust, protruding items, and varied debris. Strict enforcement of this item
and those that follow will be the responsibility of all Supervising Officers.
Contact with the third rail or the third rail cover must be avoided even when power
is confirmed to be off. Unexpected restoration of power must be anticipated. Members
crossing the third rail must not step on the third rail cover, but rather, over it.
Always operate as if power is on and avoid contact or proximity to the third rail and the
third rail contact shoes. Even with power off there are elements within the undercarriage
electrical system that possess enough voltage to cause a shock. Contact with any
undercarriage electrical components must be avoided.
Whenever members are committed to a track area, firefighters shall be assigned in pairs
to act as warning guards. The Officer in Charge shall assure that they are posted at the
perimeter of an operation. Their primary function will be to warn all operating members
of unexpected train traffic.
A member directed to halt traffic shall use a light. The light is to be held chest high and
moved in a wide horizontal motion of at least four feet. Train Operators are accustomed
to seeing trackwalkers (inspectors) carrying lights. If this horizontal motion is not used,
the firefighter might be mistaken for a walker and the train will not stop. Members must
use extreme caution; stopping a moving train with a light is not assured. They shall
ensure themselves a position of safety and warn any endangered members to stand clear.
All officers shall maintain strict control of the actions of all members of their
command.
Limit the amount of personnel committed to the track area to the minimum needed to
accomplish the goal. Rarely does an entire unit need to be on the tracks.
A pre-selected area of safety shall be a constant thought of all members for use in an
emergency situation.
Every member shall be equipped with a flashlight. Operating in a subway without
one will place his/her life and the lives of others in jeopardy.
A very dangerous condition exists when operations occur in proximity to a tunnel
entrance or exit. Visibility will be extremely poor and must be counteracted by
additional observers and extreme caution.
23
FDNY
Chapter Seventeen

EMERGENCIES
The possibility of no clearance between a moving train and the sidewall is very
pronounced in some tunnel and railroad cut areas. The pre-selected area of safety,
minimum manpower commitment and alert observers are essential in this instance. All
items of clothing must be fastened securely to prevent the possibility of loose clothing
being caught on a moving train.
Never assume power is off when railroad personnel are seen working on a 3rd rail.
They are trained and equipped to operate while tracks are "live".
Note: It is the constant awareness, preparedness, and paying attention to basics that
have kept firefighters alive.
7.5 CONSTRUCTION AND CHARACTERISTICS
The following is a list of features found in the NYC Transit System:

7.5.1 BLUE LIGHT
Near the blue light there is a power removal box, a telephone, and fire extinguisher. The
power removal box is operated by a pull down lever located inside the box. If we find
people on the tracks and we are forced to remove power, it is imperative that the
telephone near the blue light be used to inform the Desk Superintendent that power is to
be removed and the reason why (e.g. FD on scene, people on tracks and in danger of
electrocution). To operate the telephone at these locations, remove the handset from
inside the box and depress the button on the handset, keeping it depressed at all times during
the conversation. Releasing the button will terminate the call. Dial the four-digit
Subway Control Center number listed on the inside of the door cover (see Figure # 1). If
unable to make contact with the Control Center using the primary number, release the
handset button terminating the call, then depress the button on the handset and proceed to
dial one of the two alternate numbers. This communication shall be made in order to insure
that the power is not restored. If the Desk Superintendent does not receive an immediate call
from the person who operated the power removal box, power will immediately be restored on
all tracks.
SUBWAY CONTROL CENTER
4311 (BMT)
If busy dial
4211 (IND)
or
4111 (IRT)
Figure #1
24
FDNY
Chapter Seventeen

EMERGENCIES
The Power Removal Box may not necessarily be located under the blue light, but it
will be in proximity to it or across the tracks from it. This will require us to cross live
third rails and be subject to moving trains. The correct way to cross a third rail is walk
over it and not step on the third rail cover; it may fail from a person's weight if
stepped on. In those cases where the power removal box is across the tracks, consider
sending a member in another direction that does not require crossing the tracks.
Remember that the only reason for operating on track areas without the assurance that
power off is when life is in imminent peril and direct and immediate action is required
to save life. While awaiting the arrival of a hand line, there should be a dry chemical
extinguisher available to us at the blue light, but this may be missing due to vandals.
Whenever NYC Transit personnel determine that a Power Removal Box or the
Telephone is out of service, they will be covered with a bag to identify them as being out
of service. This bag will be white, with red lettering, and it will state Out Of Service.
If a member encounters an out of service Power Removal Box, the member should use
the associated Telephone to contact the Rail Control Center (RCC) to request the removal
of power. The member must identify him/herself, state the reason that the power must be
removed, and remain on the phone until they receive confirmation that power has
been removed. All members are reminded that the use of a Power Removal Box to
remove power should only be used as a last resort, when there is an imminent life
hazard. The power limits associated with the activation of a Power Removal Box can be
very extensive and may result in many trains and passengers being needlessly stranded,
requiring assistance, evacuation, and thereby compounding the incident.
The activation of a Power Removal Box, or the use of the associated
telephone, does not alleviate the Officer in Command of the responsibility of
requesting and confirming the removal of power via Department Radio, with the
Borough Communications Office.
The blue light telephone as a communication link to a token booth.
A. The blue light telephone and token booth telephone are part of a Centrex
system, very similar to the FDNY telephone system. In the Transit Authority,
they dial the last four digits to contact another telephone number in the same
exchange (an exchange is the first three digits of the telephone number).
B. If the token booth telephone is on a different exchange than the blue light
telephone, you have to replace the three-digit exchange with the two-digit
access code before dialing the four-digit number. These access codes are
usually listed inside the blue light telephone box.
To Call Exchange Dial Access Code
714
21
243
22
927
26
694
27
544
62
430
63
334
65
424
67
Example: 424-2145 becomes 67-2145
25
FDNY
Chapter Seventeen

EMERGENCIES
C. If the Truck Officer did not obtain the token booth telephone number prior to
proceeding to the location of the fire or emergency, the Officer can use any
blue light telephone to contact the Desk Superintendent. He shall request the
Desk Superintendent to relay the blue light telephone number to the FDNY
Borough Dispatcher, who shall relay the number to the Chief Officer at the
scene. The Chief Officer can then have the token booth telephone used to
call the blue light telephone to establish contact with the Truck Officer. To
use a token booth telephone, which is a conventional telephone, request the
token booth clerk to pass the telephone through the pass through
window.
The Chief Officer can call the blue light telephone with his
cellular telephone from the street, but the token booth phone is the preferred
method. The blue light telephone does not ring, there is a buzzer mounted
on the wall above the telephone that will intermittently activate.
Truck Chauffeur (LCC)
Bottom of subway entrance stairs. If booth

is within 50 yards of stairs to street, contact the
train dispatcher through the token booth clerk.
Relay any additional information to the Officer
and Chief. Verify that the officer has the token
booth telephone number.
The LCC will relay to the Chief Officer, the 7digit blue light telephone number (that the
Officer is calling from), and a report on
conditions, when the LCC receives them from
the Officer.
Truck Officer
Before proceeding to the fire location;

ascertain the token booth telephone number. If
there is an accessible blue light telephone in the
area of the fire or emergency, call the token
booth and contact the LCC.
The Officer will give the LCC the
phone number of the blue light telephone that
he is calling from and a report on conditions.
The LCC will relay this number and the report
to the Chief Officer.
7.5.2 CONTACT SHOES

Contact shoes are pieces of metal that conduct electricity from the third rail to car motors.
They stick out from the sides of the car near the wheels. There are contact shoes on
both sides of the cars. If any contact shoe is on the third rail, all contact shoes of car
will be energized.
26
FDNY
Chapter Seventeen

EMERGENCIES
7.5.3 CUT OUTS

Some benchwalls are provided with cut outs (safety niches) which are indented spaces in
the wall of the tunnel. They provide room for a person to stand while a train passes by.
When using a cutout, Firefighters are required to use the reduced-profile maneuver for
their masks. The main problem with these areas of refuge is that track gangs sometimes
use these spaces to store tools and equipment. When passing cutouts on a catwalk,
observe to see if it is clear. If a train should come by unexpectedly, go back to the cutout
you just passed, if it is clear.
7.5.4 NO CLEARANCE SIGNS
Along the walls of tunnels we will find "no clearance" signs. They are identified by diagonal
red and white stripes painted on a wall. It may appear that there is clearance at this location
but train overhang on turns and contact shoes will hit you if you are standing there
7.5.5 STEEL DUST
Some subway tunnels have been in existence since the turn of the 20th century. Wheels
and brake shoes on subway cars are made of steel. When brakes are applied on a train
there is metal to metal contact producing steel dust. Over many years this dust mixes
with oil from the passing trains. This dust forms on the walls, benchwalls, track-bed, and
under carriage of the trains. Members are cautioned to use their eye shields even for
a "Can" job as this dust is everywhere, and the minute particles of steel in the dust
have been known to blind people.
7.5.6 SUBWAY EMERGENCY EXITS
Emergency exits are stairways that lead up to the street from the track area. On the
surface, they are located on sidewalks and in ventilating towers near the river. There are
counter balance weights that will assist people to open the door. There is a bar across the
door similar to a panic bar. When a person depresses the bar, the counter balance weight
activates and the door opens. A prism-shaped sign or a cluster of 5 white lights identifies
emergency exits in subway tunnels.
The MTA Transit is installing intrusion alarms on all of their subway emergency exits.
All units inspecting an emergency exit, or responding to an incident at an emergency exit,
shall notify the Fire Department Borough Communications Office, and request that the
MTA Transit Control Center is advised that Fire Department units are entering the
emergency exit. The unit entering the exit shall communicate the exit number and the
exit location to the Borough Communications Office, for transmittal to the Transit
Control Center.
27
FDNY
Chapter Seventeen

EMERGENCIES
7.6 EMERGENCY EVACUATION DEVICE

The Emergency Evacuation Device (EED) was designed by the New York City Transit
Authoritys Office of System Safety. EEDs are provided for FDNY use and are located
throughout the Transit Authoritys subway system.
7.6.1 DESCRIPTION
A. The EED is a yellow, 7-foot long device with steps on the front (Figure 1) and a
flat surface on the backside (Figure 2). A non-skid surface is applied to both sides. Each
unit weighs approximately 42 pounds.
B. These devices are constructed of fiberglass reinforced plastic and are electrically
non- conductive for use within the confines of the subway environment.
C. When positioned against the side or end doors of a subway car the EED will reach
the roadbed at approximately a 70 angle (safe for ascent / descent) and the steps will
provide a horizontal stepping surface (Figure 3). A notch cut in the beams on one
end of the ladder helps to anchor the EED in position against the car and or platform.
7.6.2 LOCATION
A. At underground and grade level stations, the EED is located at the first Blue
Light location south of the southbound platform (typically within 50 feet of the platform
end).
B. At elevated stations, the EED will be located in the area of the full time token booth.
C. An EED is located at the base of the emergency exit, at both ends of each under
river tunnel.
D. Keys to remove EEDs from their mounting brackets are available at every token booth.
E. In Staten Island, EEDs are located near Tower B, at the Saint George Rail Terminal
and near the crew quarters at the Tottenville Train Yard.
7.6.3 ACCESS
Metal mounting brackets are provided at each location and are secured with a corrosion
resistant padlock. If a key can not be obtained, the locks can be forced using
conventional forcible entry methods.
28
FDNY
Chapter Seventeen

EMERGENCIES
7.6.4 OPERATIONS
The Emergency Evacuation Device can be used in the following three ways.
A. When passengers are being evacuated to the roadbed, the EED is positioned
with the cut out against the edge of the car floor with the step side up. The
ladder provides a safe angle for most ambulatory passengers to descend, however
personnel must be assigned to both the top and the bottom of the ladder, to
provide assistance and stability to the passengers.(Figure 3).
B. The EED can also be used as an evacuation stair to access the platform level
from the roadbed.
C. When a rescue train is used, the EED can be positioned step side down, to
form a bridge between two adjacent cars. The flat surface provides a stable
platform to walk passengers from one car to another. Personnel must be stationed
in each car to provide assistance and stability to the passengers.
Figure 1
Figure 2
Figure 3
29
FDNY
Chapter Seventeen

EMERGENCIES
7.7 NOLAN ATS-1 EMERGENCY RAIL CART

The Nolan ATS-1 Emergency Rail Cart is a lightweight aluminum cart that can be used to
transport tools, equipment and patients on tracks used by the NYC Transit, Amtrak, Long
Island Railroad, Staten Island Rapid Transit, Metro North, and PATH transit systems.
The rail cart consists of 2 base sections, each weighing 48 lbs, 2 handles to push or pull
the rail cart along the tracks, 1 connector plate, cargo net with tie-downs, 2 red cam
buckle straps and 2 yellow ratchet straps for securing rail cart to apparatus. All
components are packaged together on a modified hand truck for storage in quarters and
transportation to incident (Photo 1).
Photo 1
7.7.1 STORAGE AND TRANSPORTATION

Company Commanders shall ensure rail carts are stored in a visible location on the
apparatus floor which is easily accessible for rapid response and when needed, to enable
special called units to locate the rail cart. Rail carts shall only be secured to the apparatus
when special called for an operation or training.
When rail carts are transported to an incident, the following procedures shall be followed:
Make sure the components are secured to hand truck.
Place entire package on back step of apparatus (Photo 2).
Secure with two yellow ratchet straps provided (Photos 3-4).
Tighten straps with ratchet.
30
FDNY
Chapter Seventeen

EMERGENCIES
Note: Proper usage of the yellow ratchet straps is essential to getting the rail cart to
location safely. Straps must be initially positioned to allow for free use of
ratcheting mechanism. This will enable member to properly tighten the
straps securing the unit to the apparatus.
Upper strap to
grab handles.
Lower strap to
lower tow loops.
Photo 2
Release Lever
Photo 3
Photo 4
Hook upper strap with carabiners on grab handles. Hook lower strap with carabiners on
lower tow loops (Photo 3).
To tighten yellow straps, pull release lever on ratchet handle and tighten ratchet. To lock
ratchet, pull release lever and bring ratchet handle to nested position (Photo 4).
Any engine company may be special called to transport a rail cart from the quarters
where it is stored to the scene of an incident. Laminated instruction cards outlining rail
cart transportation and use are attached to the rail cart hand truck.
7.7.2 ASSEMBLY OF RAIL CART
Place each half of rail cart on track with the wheels on the rail cart positioned close to the
operator, with the operators facing each other (Photo 5).
Insert handles into sockets on each half of rail cart sections, then secure with hitch pin
clips (Photo 6).
-31-
FDNY
Chapter Seventeen

EMERGENCIES
Photo 5
Photo 6
Using handles for leverage, have each member place one foot onto rail cart and raise front
to an approximate 450 angle, so that each connection point joins to one another (Photo 7).
Raise one section slightly higher than the other until pin seats into slot (Photos 7-8).
Photo 7
Photo 8
Slowly lower halves until they join together and lie flat onto tracks and the rail cart is in
position for use (Photo 9-10).
Photo 9
Photo 10
- 32 -
FDNY
Chapter Seventeen

EMERGENCIES
One wheel is provided with a wheel lock (slide bolt). A red square is painted on the
surface corner of the rail cart to denote the location of the wheel lock (Photo 11). Once
assembled, the member can use the wheel lock to secure rail cart from rolling.
Note sliding bolt
and wheel
receptacle.
Photo 11
Two rail carts can be connected together using the connector plate (Photo 12-13).
Photo 12
Photo 13
Tools, equipment or non-ambulatory victims may be secured to the rail cart using
supplied elastic cargo net, red cam buckle straps, or utility rope utilizing clips positioned
around the rail carts edge (Photos 14 17).
- 33 -
FDNY
Chapter Seventeen

EMERGENCIES
Photo 14
Photo 15
Photo 16
Photo 17
7.7.3 DEPLOYMENT
The response policy for the Nolan rail carts is as follows:
Upon transmission of Signal 7-5 (All Hands) "Doubtful" or greater alarm for a
Railroad Incident at NYC Transit, Amtrak, Long Island Railroad, Staten Island Rapid
Transit, Metro North, and PATH transit systems.
When requested by the Incident Commander.
Upon arrival at the incident, the officer shall report to the Command Post and inform the
IC of the availability of the rail cart. Members shall remove the rail cart from the apparatus
and prepare for ground transport. When ordered to deploy the rail cart, the officer shall
determine the best access point and order the members to transport the rail cart to the scene
using the hand truck. Every effort should be made to keep the rail cart packaged together.
When necessary, individual components from the hand truck can be separated, and then
carried to the designated area.
- 34 -
FDNY
Chapter Seventeen

EMERGENCIES
Deployment of rail carts needs to be part of a carefully developed plan. For example, setting
up a rail cart prematurely on tracks being used for the evacuation of ambulatory civilians may
hinder operations. Likewise, rail carts cannot be moved both ways on the same tracks
simultaneously. The operational plan needs to consider how many rail carts and what
equipment needs to be transported to the incident scene. When all rail carts have been moved
to the scene, they can then be used in reverse order to remove non-ambulatory victims.
Avoid allowing equipment to extend beyond the sides of the cart to prevent contact with
tunnel walls or the third rail. Likewise, stretchers and stokes baskets should extend over the
front and rear of the cart, instead of the sides.
When there is a heavy load or when used on a steep grade, the cart should be pushed by or
pulled by two (2) or more members. Utility ropes and/or straps may be used to increase
control.
A connector plate is supplied to join two carts together.
connector plate might be useful at large incidents.
Joining carts together with
7.7.4 REMOUNTING RAIL CART ONTO HAND TRUCK

Rail cart sections are color coded for mounting back onto hand truck. Hand truck has a
specially designed step plate to accommodate the cart sections.
Place rail cart sections on hand truck as per color coding (Photo 18):
A. First, match orange marking on diamond plate of cart section to orange
marking painted on hand truck make sure diamond plate is facing the hand truck
and marked side-beam (orange and green) is facing up.
B. Place second cart section onto the hand truck with diamond plated in and
the painted side-beam facing up. Correct placement will have all color coding
matched up orange on cart section to orange on hand truck and cart section(orange
and green) to cart section(orange and green).
C. To ensure proper nesting of two cart sections onto the hand truck, the wheel of
the inner section (green marking) must be lifted while the outer section is seated.
D.
Secure to hand truck with red cam buckle straps (Photo 19).
- 35 -
FDNY
Chapter Seventeen

EMERGENCIES
Photo 18
Photo 19
E. Place handles between hand truck and cart sections (Photo 20).
F. Tie handles to cart, using slack from red retraining straps (Photo 21).
Photo 20
Photo 21
7.7.5 TRAINING
Company Commanders shall ensure that all members are familiar with the storage and
operation of rail carts.
Two rail carts will be available at the Bureau of Training, for use at the subway training
module.
Additional instructions on how to assemble the rail cart can be found on laminated
instructional guides attached to rail carts.
- 36 -
FDNY
Chapter Seventeen

EMERGENCIES
7.7.6 SAFETY
Operating on rail tracks is inherently dangerous. Use of rail carts, while necessary, has
the potential to increase this danger.
The wheel lock must be engaged when the cart is left unattended. This is especially
important when a cart is operated on a grade, is loaded with patients, or carrying equipment.
Note: All safety precautions, as stated in Department bulletins and in operating guides
for individual transit systems, must be followed. Particular attention must be
paid to AUC 207, section 7.
7.7.8 MAINTENANCE AND REPAIR
Company Commanders shall establish schedules to ensure that the carts are inspected
periodically. Each cart section and hand truck shall be marked with Unit designation to
ensure proper identification.
Carts shall be decontaminated as per established procedures.
- 37 -
FDNY
Chapter Seventeen

EMERGENCIES
8.
MISCELLANEOUS EMERGENCIES:
8.1
GASOLINE LEAK AUTOMOTIVE

Caution: No open lights or smoking, sparks etc. Keep area clear of people.
Leaking fuel line.
Wash down if necessary.
To stop leak :
o Crimp fuel line.
o Plug with pencil, golf tee, shaved stick or chock, etc.
Leaking gas tank.

Plug hole with small piece of tapered wood.
Rub piece of chalk over pinhole leaks.
Use commercial product such as "Loctite".
Use half of rubber ball (tennis, spalding) propped with stick forming
airtight seal with suction side towards leak.
Cut straps of gas tank, lower to ground and prop so that leak is above fuel
level.
NOTE: Often the reason for hole is that someone found it easier to steal
gas by punching hole with ice pick in preference to using siphon.
8.2
FISH HOOK REMOVAL

Fish hook embedded in finger.
Action to be taken:
If barb is not embedded, then back the hook out.
lf barb is embedded then have physician remove it.
NOTE: If medical aid is not available then push hook through until barb
protrudes. Cut the hook either at the barb or shank and remove it.
- 38 -
FDNY
Chapter Seventeen
8.3

EMERGENCIES
RING REMOVAL:
Use a soapy water as lubricant for ring removal.
Finger may be cooled which will decrease swelling and allow removal.
Use or call for ring cutter which will safely cut ring off finger in short period of
time - less than a minute.
NOTE:
8.4
Sometimes it is preferable to use regular cutting pliers because ring cutter will not
cut stainless steel.
BURGLAR ALARM RINGING:

Many times due to a fire, a burglar alarm may be constantly ringing. This constant
noise during overhaul could possibly make members tense and set up a situation
where injuries occur.
Burglar alarms may be silenced by either of the below methods.
Locate alarm and insert wad of paper, chock, match book cover, etc.
between clapper and bell.
Disconnect power.
o Locate alarm.
o Follow wire into occupancy.
o Locate alarm box with batteries.
o Use screw driver or dime to remove cover.
o Disconnect wires from battery terminals.
o Replace cover.
NOTE: If wires are connected to house electric pull plug, pull fuse, or turn off power
- 39 -
FDNY
Chapter Seventeen
8.5

EMERGENCIES
OIL SLICK IN ROADWAY:

Oil slick can cause accident and may be most common after an accident.
Operation:
Check immediate area for sand or dirt. Use shovels to spread same onto
slick. This will absorb oil or at least provide a friction cover to prevent
slipping. The use of water on slick will only exacerbate the problem.
If no sand available call for sanitation sand truck.
8.6
SULFUR CANDLES:
Sulfur candles are used to discourage vermin. The fumes produced are highly
irritating.
Operations:
Use mask.
Use as few members as possible preferably (officer and one firefighter).
Vent as you search.
When candle is found, either extinguish or remove to outer air.
Wait outside apartment for sufficient time to establish fact that no other
candles remain.
NOTE: Candles are usually found on the floor in a saucer of water.
8.7
ICE RESCUE:
Cautions:
A ladder will spread out and diminish the weight on a specific area of ice to allow
greater safety and enhance the possibility of removing someone from ice or icy
water.
Actions:
Ladder extended with rope tied on shoreward rung. Rope will serve as an
extension.
Rescuer crawls out on ladder to assist victim if necessary.
If ice breaks ladder will angle upwards and can be drawn back to safety.
Hook can be extended to victim. (Hook of necessary length.)
Other devices to use are buoys, ropes, sticks, poles or even a human chain
lying prone on the ice.
Be prepared to give Rescue Breathing and treat for shock.

- 40 -
FDNY
Chapter Seventeen
9.

EMERGENCIES
CONCLUSION
This chapter has covered some of the most common emergencies (outside fire
emergencies) that the FDNY is called to respond to. As mentioned earlier, fire calls
account for roughly 20 to 25% of FDNY responses. Recognizing this, its critical that
firefighters are proficient at providing assistance at other types of incidents in addition to
fires. To operate proficiently actions taken should always be based on sound principles
regarding effectiveness and safety. Without regards for such, even the smallest incident
can escalate quickly to disastrous consequences.
- 41 -

Probationary Firefighters Manual

Uploaded by

Copyright:

Available Formats

Probationary Firefighters Manual

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Probationary Firefighters Manual

Uploaded by

Copyright:

Available Formats

Probationary Firefighters Manual

To make members aware of the nature of the most commonly

FDNY All Unit Circulars

WATER CONDITIONS ....................................................... 1

STEAM CONDITIONS ....................................................... 9

NATURAL GAS EMERGENCIES ........................................ 13

OIL BURNER EMERGENCIES ........................................... 17

VEHICULAR ACCIDENTS ................................................. 18

SUBWAY EMERGENCIES .................................................. 20

MISCELLANEOUS EMERGENCIES .................................... 38

on the wall near the ceiling of the apartment directly below.

on riser line of apartments in basements.

WATER CONDITIONS: WATER LEAKS