Lab - Initializing and Reloading A Router and Switch

L
Lab - Initializing
g and Re
eloading
g a Routter and S
Switch
T
Topology
O
Objectives
Part 1: Se
et Up Device
es in the Netw
work as Show
wn in the To
opology
Part 2: Initialize the Router
R
and Reload
Part 3: Initialize the Switch
S
and Reload
B
Backgroun
nd / Scenarrio
Before sta
arting a CCNA
A hands-on la
ab that makes
s use of eithe r a Cisco router or switch, ensure that tthe
devices in
n use have be
een erased an
nd have no sttartup configu
urations prese
ent. Otherwise
e, the results of your
lab may be
b unpredictab
ble. This lab provides
p
a de
etail procedure
e for initializin
ng and reload
ding a Cisco router and
a Cisco sw
witch.
Note: The
e routers used
d with CCNA hands-on lab
bs are Cisco 1
1941 Integrate
ed Services R
Routers (ISRss) with
Cisco IOS
S Release 15..2(4)M3 (univ
versalk9 image). The switch
hes used are
e Cisco Catalyyst 2960s with
h Cisco
IOS Relea
ase 15.0(2) (lanbasek9 ima
age). Other ro
outers, switch
hes, and Ciscco IOS version
ns can be use
ed.
Depending on the mod
del and Cisco IOS version, the comman
nds available a
and output prroduced migh
ht vary
from whatt is shown in the
t labs.
R
Required Resources
R
1 Rou
uter (Cisco 19
941 with Cisco
o IOS softwarre, Release 1 5.2(4)M3 universal image or comparab
ble)
1 Switch (Cisco 29
960 with Cisco
o IOS Release 15.0(2) lanb
basek9 image
e or compara
able)
2 PCs
s (Windows 7,
7 Vista, or XP
P with termina
al emulation p
program, such
h as Tera Term)
Conso
ole cables to configure the
e Cisco IOS devices via the
e console porrts
P
Part 1:
Set
S Up De
evices in the Netw
work as Sh
hown in tthe Topo
ology
S
Step 1: Ca
able the netw
work as sho
own in the topology.
t
Attach console cables to the devices shown in th
he topology diiagram.
S
Step 2: Po
ower on all the
t devices in the topo
ology.
Wait for all
a devices to finish
f
the softw
ware load pro
ocess before moving to Pa
art 2.
2013 Cisco and

d/or its affiliates. All rights reserve
ed. This docume
ent is Cisco Publiic.
Page 1 of 4
Initializing and Reloading a Router and Switch
Part 2:
Initialize the Router and Reload
Step 1: Connect to the router.

Console into the router and enter privileged EXEC mode using the enable command.
Router> enable
Router#
Step 2: Erase the startup configuration file from NVRAM.

Type the erase startup-config command to remove the startup configuration from nonvolatile randomaccess memory (NVRAM).
Router# erase startup-config
Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
[OK]
Erase of nvram: complete
Router#
Step 3: Reload the router.

Issue the reload command to remove an old configuration from memory. When prompted to Proceed with
reload, press Enter to confirm the reload. Pressing any other key will abort the reload.
Router# reload
Proceed with reload? [confirm]
*Nov 29 18:28:09.923: %SYS-5-RELOAD: Reload requested by console. Reload Reason:
Reload Command.
Note: You may receive a prompt to save the running configuration prior to reloading the router. Respond
by typing no and press Enter.
System configuration has been modified. Save? [yes/no]: no
Step 4: Bypass the initial configuration dialog.

After the router reloads, you are prompted to enter the initial configuration dialog. Enter no and press Enter.
Would you like to enter the initial configuration dialog? [yes/no]: no
Step 5: Terminate the autoinstall program.

You will be prompted to terminate the autoinstall program. Respond yes and then press Enter.
Would you like to terminate autoinstall? [yes]: yes
Router>
Part 3:
Initialize the Switch and Reload
Step 1: Connect to the switch.

Console into the switch and enter privileged EXEC mode.
Switch> enable
Switch#
2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.
Page 2 of 4
Step 2: Determine if there have been any virtual local-area networks (VLANs) created.
Use the show flash command to determine if any VLANs have been created on the switch.
Switch# show flash
Directory of flash:/
2
3
4
5
6
-rwx
-rwx
-rwx
-rwx
-rwx
1919
1632
13336
11607161
616
Mar
Mar
Mar
Mar
Mar
1
1
1
1
1
1993
1993
1993
1993
1993
00:06:33
00:06:33
00:06:33
02:37:06
00:07:13
+00:00
+00:00
+00:00
+00:00
+00:00
private-config.text
config.text
multiple-fs
c2960-lanbasek9-mz.150-2.SE.bin
vlan.dat
32514048 bytes total (20886528 bytes free)

Switch#
Step 3: Delete the VLAN file.

a. If the vlan.dat file was found in flash, then delete this file.
Switch# delete vlan.dat
Delete filename [vlan.dat]?
You will be prompted to verify the file name. At this point, you can change the file name or just press
Enter if you have entered the name correctly.
b. When you are prompted to delete this file, press Enter to confirm the deletion. (Pressing any other key will
abort the deletion.)
Delete flash:/vlan.dat? [confirm]
Switch#
Step 4: Erase the startup configuration file.

Use the erase startup-config command to erase the startup configuration file from NVRAM. When you are
prompted to remove the configuration file, press Enter to confirm the erase. (Pressing any other key will abort
the operation.)
Switch# erase startup-config
Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
[OK]
Erase of nvram: complete
Switch#
Step 5: Reload the switch.

Reload the switch to remove any old configuration information from memory. When you are prompted to
reload the switch, press Enter to proceed with the reload. (Pressing any other key will abort the reload.)
Switch# reload
Proceed with reload? [confirm]
Note: You may receive a prompt to save the running configuration prior to reloading the switch. Type no
and press Enter.
System configuration has been modified. Save? [yes/no]: no
Page 3 of 4
Step 6: Bypass the initial configuration dialog.

After the switch reloads, you should see a prompt to enter the initial configuration dialog. Type no at the
prompt and press Enter.
Would you like to enter the initial configuration dialog? [yes/no]: no
Switch>
Reflection
1. Why is it necessary to erase the startup configuration before reloading the router?
2. You find a couple configurations issues after saving the running configuration to the startup configuration, so
you make the necessary changes to fix those issues. If you were to reload the device now, what configuration
would be restored to the device after the reload?
Page 4 of 4

Lab - Initializing and Reloading A Router and Switch

Uploaded by

Copyright:

Available Formats

Lab - Initializing and Reloading A Router and Switch

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lab - Initializing and Reloading A Router and Switch

Uploaded by

Copyright:

Available Formats

L

2013 Cisco and

Initializing and Reloading a Router and Switch

Initialize the Router and Reload

Step 1: Connect to the router.

Step 2: Erase the startup configuration file from NVRAM.

Step 3: Reload the router.

Step 4: Bypass the initial configuration dialog.

Step 5: Terminate the autoinstall program.

Initialize the Switch and Reload

Step 1: Connect to the switch.

Initializing and Reloading a Router and Switch

32514048 bytes total (20886528 bytes free)

Step 3: Delete the VLAN file.

Step 4: Erase the startup configuration file.

Step 5: Reload the switch.

Initializing and Reloading a Router and Switch

Step 6: Bypass the initial configuration dialog.

You might also like