Router Control Panel Series

Copyright 2009 -2012

EVERTZ MICROSYSTEMS LTD.
5288 John Lucas Drive,
Burlington, Ontario, Canada
L7L 5Z9
Phone:
+1 905-335-3700
Sales Fax:
+1 905-335-3573
Tech Support Phone: +1 905-335-7570
Tech Support Fax:
+1 905-335-7571
Internet: Sales:
Tech Support:
Web Page:

[email protected]
[email protected]
http://www.evertz.com

Version 1.4, February 2012

The material contained in this manual consists of information that is the property of Evertz Microsystems and is
intended solely for the use of purchasers of the CP Panels. Evertz Microsystems expressly prohibits the use of this
manual for any purpose other than the operation of the device.
All rights reserved. No part of this publication may be reproduced without the express written permission of Evertz
Microsystems Ltd. Copies of this guide can be ordered from your Evertz products dealer or from Evertz
Microsystems.

This page left intentionally blank

IMPORTANT SAFETY INSTRUCTIONS

The lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of un-insulated Dangerous voltage
within the products enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (Servicing) instructions
in the literature accompanying the product.

Read these instructions

Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturers instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than other. A grounding-type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.

WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE
WARNING
DO NOT EXPOSE THIS EQUIPMENT TO DRIPPING OR SPLASHING AND ENSURE THAT NO
OBJECTS FILLED WITH LIQUIDS ARE PLACED ON THE EQUIPMENT
WARNING
TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE AC MAINS, DISCONNECT THE
POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE
WARNING
THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY OPERABLE

INFORMATION TO USERS IN EUROPE

NOTE
This equipment with the CE marking complies with both the EMC Directive (2004/108/EC) and the Low Voltage
Directive (2006/95/EC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following European standards:
EN60950
Product Safety
EN55103-1
Electromagnetic Interference Class A (Emission)
EN55103-2
Electromagnetic Susceptibility (Immunity)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to the
European Union EMC directive. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
EN60950
EN55103-1: 1996
EN55103-2: 1996

Safety
Emission
Immunity

EN504192 2005
Waste electrical products should not
be disposed of with household
waste. Contact your Local Authority
for recycling advice

INFORMATION TO USERS IN THE U.S.A.

NOTE
FCC CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING
Changes or Modifications not expressly approved by Evertz Microsystems Ltd. could void the users authority to
operate the equipment.
Use of unshielded plugs or cables may cause radiation interference. Properly shielded interface cables
with the shield connected to the chassis ground of the device must be used.
Evertz Microsystems Ltd
Tested to comply with
FCC Standards

For Home or Office Use

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:
This device may cause harmful interference, and
This device must accept any interference received, including
interference that may cause undesired operation.

ELECTROSTATIC SENSITIVE DEVICES

The hand symbol within an equilateral triangle is intended to alert the user
to instructions related to precautions for handling electrostatic-sensitive
devices. See Electro Static Discharge (ESD) Precautions section for
further details.

INFORMATION FOR NEBS COMPLIANT VERSIONS

The intra-building port(s) of this equipment is suitable for connection to
intrabuilding or unexposed wiring or cabling only. The intra-building port(s)
of the equipment MUST NOT be metallically connected to interfaces that
connect to the OSP or its wiring. These interfaces are designed for use as
intra-building interfaces only (Type 2 or Type 4 ports as described in GR1089-CORE, Issue 4) and require isolation from the exposed OSP cabling.
The addition of Primary Protectors is not sufficient protection in order to
connect these interfaces metallically to OSP wiring.

This equipment must be installed in a restricted access location.

This equipment is to be connected to a Common Bonding Network. See

Installation section for further information.

This equipment is to be installed in the network telecommunication facilities.

This page left intentionally blank

Control Panel Series

REVISION HISTORY
DESCRIPTION

REVISION

DATE

0.1

Preliminary

Jul 2008

0.2

Added Installation and configuration information

Dec 2008

0.3

Removed references to Q-Link, WinSetup, CHOP & ENGINEERING functions

Feb 2009

1.0

Released

Mar 2009

1.1

Added information on the control system, configuration with rotary encoder,

configuring with LCD button panels.

May 2009

1.2

Removed references to single destination mode in section 1.3.5 and fuse info

Dec 2009

1.3

Revised for E series control panels

Apr 2010

1.4

Added Desktop Mounting Kits information

Feb 2012

Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof
nor for the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning
performance of Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. The
only warranty offered by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order
confirmation form.
Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no
warranty is granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or
order confirmation. Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If
you encounter an error, please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make
changes in equipment design or specifications.

REVISION HISTORY

Revision 1.4

Page i

Control Panel Series

This page left intentionally blank

Page ii

Revision 1.4

REVISION HISTORY

Control Panel Series

TABLE OF CONTENTS
1.

PANEL TYPE OVERVIEW................................................................................................. 1

1.1. BUTTON PER SOURCE CONTROL PANELS ..................................................................... 1
1.1.1. CP-1604E Remote Control Panel .............................................................................. 1
1.1.2. CP-3201E Remote Control Panel .............................................................................. 2
1.1.3. CP-6401E Remote Display Panel, Multi-Mode, 80 Button-Per-Source ...................... 2
1.2. INTELLIGENT LCD BUTTON CONTROL PANELS ............................................................. 3
1.2.1. CP-1000E Remote Control Panel .............................................................................. 3
1.2.2. CP-2024E Remote Control Panel .............................................................................. 4
1.2.3. CP-2032E Remote Control Panel .............................................................................. 4
1.2.4. CP-2048E Remote Control Panel .............................................................................. 5
1.3. XY/MULTI-BUS CONTROL PANELS ................................................................................... 6
1.3.1. CP-2402E Dual Display Remote Control Panel ......................................................... 6
1.3.2. CP-3200E Remote Panel with Keypad and Display ................................................... 7
1.3.3. CP-3208E Remote Control Panel .............................................................................. 7
1.3.4. CP-6400E Remote Display Panel, XY Keypad .......................................................... 8
1.3.5. CP-6408E Remote Control Panels ............................................................................ 8

2.

INSTALLATION ................................................................................................................. 9
2.1. ELECTRO STATIC DISCHARGE (ESD) PRECAUTIONS .................................................... 9
2.2. MOUNTING .......................................................................................................................... 9
2.2.1. Desk Top Mounting ................................................................................................... 9
2.2.2. Grounding and Bonding NEBS Applications ......................................................... 10
2.3. COOLING ........................................................................................................................... 12
2.4. USE OF SHIELDED CABLES ............................................................................................ 12
2.5. REAR PANEL CONNECTIONS .......................................................................................... 12
2.5.1. Connecting the Panels using Q-link ......................................................................... 12
2.5.2. RS232/422 Computer Port ...................................................................................... 16
2.5.3. Connecting the Control Panels using Ethernet ........................................................ 16
2.5.4. Debug RS-232 Port ................................................................................................. 18
2.5.5. SERIAL RS232/422 Serial Ports ............................................................................. 18
2.5.6. Joystick Override ..................................................................................................... 19
2.5.7. Power ...................................................................................................................... 19
2.6. CONFIGURING REMOTE CONTROL PANELS................................................................. 20
2.6.1. Configuring ANY Panel via the Rotary Shaft Encoder ............................................. 20
2.6.2. Configuring Intelligent LCD Button Panels via Front Panel LCD Buttons ................. 21

3.

CONTROL PANELS AND OPERATION ......................................................................... 22

3.1. CONFIGURING PANELS ................................................................................................... 22
3.2. COMMON FEATURES OF ALL CONTROL PANELS ........................................................ 22
3.2.1. Buzzer Feature ........................................................................................................ 22
3.2.2. Joystick or Micro-switch Override ............................................................................ 22

TABLE OF CONTENTS

Revision 1.4

Page iii

Control Panel Series

3.2.3. Computer Port ......................................................................................................... 22
3.3. CONTROL PANEL TYPE: CP-1604E................................................................................. 23
3.3.1. Sources Button ........................................................................................................ 23
3.4. CONTROL PANEL TYPE: CP-3201E................................................................................. 23
3.4.1. Destinations ............................................................................................................ 24
3.4.2. Sources Button ........................................................................................................ 24
3.4.3. Breakaways ............................................................................................................. 24
3.4.4. Lock Button ............................................................................................................. 24
3.5. CONTROL PANEL TYPE: CP-6401E................................................................................. 25
3.5.1. Destinations ............................................................................................................ 25
3.5.2. Sources Button ........................................................................................................ 25
3.5.3. Breakaways ............................................................................................................. 25
3.5.4. Lock Button ............................................................................................................. 26
3.6. CONTROL PANEL TYPE: CP-1000E................................................................................. 26
3.6.1. Sources Button ........................................................................................................ 26
3.7. CONTROL PANEL TYPE: CP-2024E................................................................................. 27
3.8. CONTROL PANEL TYPE: CP-2032E................................................................................. 27
3.9. CONTROL PANEL TYPE: CP-2048E................................................................................. 27
3.10. CONTROL PANEL TYPE: CP-2402E................................................................................. 28
3.10.1. Destinations ............................................................................................................ 28
3.10.2. Sources Button ........................................................................................................ 28
3.10.3. Breakaways ............................................................................................................. 28
3.10.4. Lock Button ............................................................................................................. 29
3.11. CONTROL PANEL TYPE: CP-3200E................................................................................. 29
3.11.1. Keypad .................................................................................................................... 30
3.11.2. Clear ....................................................................................................................... 30
3.11.3. Destinations ............................................................................................................ 30
3.11.4. Sources Button ........................................................................................................ 30
3.11.5. Take Button ............................................................................................................. 30
3.11.6. Breakaways ............................................................................................................. 30
3.11.7. Lock Button ............................................................................................................. 30
3.12. CONTROL PANEL TYPE: CP-3200E IN 5 BUS MODE ..................................................... 31
3.12.1. Keypad .................................................................................................................... 31
3.12.2. Clear ....................................................................................................................... 31
3.12.3. Sources Button ........................................................................................................ 31
3.12.4. Destinations ............................................................................................................ 31
3.12.5. Breakaways ............................................................................................................. 31
3.12.6. Lock Button ............................................................................................................. 31
3.13. CONTROL PANEL TYPE: CP-3208E................................................................................. 32
3.13.1. Sources Button ........................................................................................................ 32
3.13.2. Lock Button ............................................................................................................. 32
3.14. CONTROL PANEL TYPE: CP-6400E................................................................................. 33
3.14.1. Keypad .................................................................................................................... 33
3.14.2. Clear ....................................................................................................................... 33
3.14.3. Destinations ............................................................................................................ 33

Page iv

Revision 1.4

TABLE OF CONTENTS

Control Panel Series

3.14.4. Sources Button ........................................................................................................ 34
3.14.5. Take Button ............................................................................................................. 34
3.14.6. Breakaways ............................................................................................................. 34
3.14.7. Lock Button ............................................................................................................. 34
3.15. CONTROL PANEL TYPE: CP-6408E................................................................................. 35
3.15.1. Keypad .................................................................................................................... 35
3.15.2. Clear ....................................................................................................................... 35
3.15.3. Sources Button ........................................................................................................ 35
3.15.4. Take Button ............................................................................................................. 35
3.15.5. Breakaways ............................................................................................................. 36
3.15.6. Lock Button ............................................................................................................. 36

4.

SPECIFICATIONS ........................................................................................................... 37
4.1. POWER .............................................................................................................................. 37
4.2. PHYSICAL .......................................................................................................................... 37
4.3. CONTROL .......................................................................................................................... 37
4.4. UPGRADING THE FIRMWARE .......................................................................................... 38
4.4.1. Overview ................................................................................................................. 38
4.4.2. Terminal Program Setup ......................................................................................... 38
4.4.3. Initiating Firmware Upgrade Mode from the Terminal Program ............................... 38
4.4.4. Uploading the New Firmware .................................................................................. 39
4.5. SERVICING INSTRUCTIONS............................................................................................. 40
4.5.1. Changing the Fuses ................................................................................................ 40
4.5.2. Enabling/Disabling the Buzzer ................................................................................. 40

TABLE OF CONTENTS

Revision 1.4

Page v

Control Panel Series

Figures
Figure 1-1: CP-1604E Control Panel ................................................................................................................ 2
Figure 1-2: CP-3201E Control Panel ................................................................................................................ 2
Figure 1-3: CP-6401E Control Panel ................................................................................................................ 2
Figure 1-4: CP-1000E Control Panel ................................................................................................................ 3
Figure 1-5: CP-2024E Control Panel ................................................................................................................ 4
Figure 1-6: CP-2032E Control Panel ................................................................................................................ 4
Figure 1-7: CP-2048E Control Panel ................................................................................................................ 5
Figure 1-8: CP-2402E Remote Control Panel................................................................................................... 6
Figure 1-9: CP-3200E Control Panel ................................................................................................................ 7
Figure 1-10: CP-3208E Control Panel .............................................................................................................. 7
Figure 1-11: CP-6400E Control Panel .............................................................................................................. 8
Figure 1-12: CP-6408E Control Panel .............................................................................................................. 8
Figure 2-1: Desk Top Mounting Configuration ................................................................................................ 10
Figure 2-2: NEBS Bonding System ................................................................................................................. 11
Figure 2-3: Rear Panel .................................................................................................................................... 12
Figure 3-1: CP-1604E Control Panel .............................................................................................................. 23
Figure 3-2: CP-3201E Control Panel .............................................................................................................. 23
Figure 3-3: CP-6401E Control Panel .............................................................................................................. 25
Figure 3-4: CP-1000E Control Panel .............................................................................................................. 26
Figure 3-5: CP-2024E Control Panel .............................................................................................................. 27
Figure 3-6: CP-2032E Control Panel .............................................................................................................. 27
Figure 3-7: CP-2048E Control Panel .............................................................................................................. 27
Figure 3-8: CP-2402E Control Panel .............................................................................................................. 28
Figure 3-9: CP-3200E Control Panel .............................................................................................................. 29
Figure 3-10: CP-3208E Control Panel ............................................................................................................ 32
Figure 3-11: CP-6400E Control Panel ............................................................................................................ 33
Figure 3-12: CP-6408E Control Panel ............................................................................................................ 35

Tables
Table 2-1: Bonding Parts Included with NEBS Compliant Version ................................................................. 11
Table 2-2: Standard RJ-45 Wiring Colour Codes ........................................................................................... 17
Table 2-3: DEBUG Port Pin Connections ....................................................................................................... 18
Table 2-4: SERIAL Port Pin Connections ....................................................................................................... 18
Table 2-5: JOYSTICK Port Pin Connections .................................................................................................. 19

Page vi

Revision 1.4

TABLE OF CONTENTS

Control Panel Series

1.

PANEL TYPE OVERVIEW

The panels in this manual are supported by two types of Evertz router control systems; our advanced
award winning EQX Server, and our legacy router controller, the SC-1000. Additionally most of our
routers, for smaller applications and for legacy reasons, support directly connecting router panels.
Panels connected to the EQX Server are ALWAYS ONLY connected via Ethernet. The panel
configuration is managed and hosted by EQX Server. Panels connected DIRECTLY to a router or
connected to the legacy SC-1000 are ALWAYS ONLY connected via QLINK, are hosted by the router
or SC-1000 and are managed by Winsetup software. For details on configuring and connecting the
panels to an appropriate router control system refer to section 2.6 Configuring Remote Control
Panels of this manual. Please note that the panels have very similar operation between EQX Server
and in legacy mode and may vary slightly from the descriptions of functions within this manual. For
more specific features of the panels as they relate to the 2 types of router control systems please see
either the EQX Server manual or the Winsetup Help File.

1.1.

BUTTON PER SOURCE CONTROL PANELS

The Button per Source panels are versatile programmable panels with 20, 40 or 80 illuminated push
buttons. A wide range of panel operations including XY and multi-destination may be configured using
the router control system. Buttons can be individually configured for any combination of source,
destination, breakaway or control functions.
Features:
15mm square buttons suitable for film legends with green LED illumination, uniform over whole
legend surface
Buttons with high quality positive action
All panels are fully programmable to operate in a number of modes
Split panels can be programmed in many ways, for instance, permitting two separate
destinations to be controlled using two rows of source buttons
Buttons can be programmed for breakaways
Program/Preview/Take mode can be programmed, emulating vision mixer operation, useful in
transmission environments
Optional Lock button protects against accidental or unauthorized selections
Camera joystick override on any eight GPI inputs, with momentary or latching action
1.1.1.

CP-1604E Remote Control Panel

The CP-1604E is a fully programmable panel and therefore the operation of the panel is entirely
dependent upon its configuration. The CP-1604E has 20 illuminated push buttons and is ideal for use
with 16 sources leaving four buttons to select breakaways, lock, and destinations, etc.
See section 3.3 for more information on the operation of the CP-1604E Control Panel.

Revision 1.4

Page 1

Control Panel Series

Figure 1-1: CP-1604E Control Panel

1.1.2.

CP-3201E Remote Control Panel

The CP-3201E is a fully programmable panel and therefore the operation of the panel is entirely
dependent upon its configuration. The CP-3201E has 40 illuminated pushbuttons and is ideal for use
with 32 sources leaving eight buttons to select destinations, breakaways and lock, etc. Alternatively, it
can be programmed with 16 source buttons and 16 destination buttons to provide an XY panel
suitable for small systems.
See section 3.4 for more information on the operation of the CP-3201E Control Panel.

Figure 1-2: CP-3201E Control Panel

1.1.3.

CP-6401E Remote Display Panel, Multi-Mode, 80 Button-Per-Source

The CP-6401E is a fully programmable panel and therefore the operation of the panel is entirely
dependent upon its configuration. The CP-6401E has 80 illuminated pushbuttons and is ideal for use
with 64 sources in systems that require selection of the source with a single button press leaving 16
buttons to select destinations, breakaways and lock, etc. Alternatively, it can be used as an XY panel
for systems up to 32x32.
See section 3.5 for more information on the operation of the CP-6401E Control Panel.

Figure 1-3: CP-6401E Control Panel

Page 2

Revision 1.4

Control Panel Series

1.2.

INTELLIGENT LCD BUTTON CONTROL PANELS

The Intelligent LCD Button control panels feature assignable and dynamic LCD button technology.
Each of the LCD buttons is capable of displaying multiple text characters. These panels can be
programmed to have many pages of menus allowing users to select a large number of sources or
destinations.
When a menu button is pressed, some or all of the buttons change their function and legend. Their
operation is then defined by the configuration setup for this menu.
Features:
Flexible menu driven configurations providing quick and simple access
Easily reconfigured for regularly changing environments
Each LCD display features a 32x24 dot matrix capable of supporting two or three rows of five
character text
Each LCD display supports full RGB illumination with two level programmable intensity
providing unprecedented visual indication of the button status
Fully programmable button operation - user-definable
Button-per-source selection with Page mode NEXT and LAST buttons to select more sources
LOCK or ENABLE button to protect against unauthorized or accidental selection
Buttons can be programmed for breakaways or to give a menu structure to the panel
Camera joystick override on any eight GPI inputs, with momentary or latching action

1.2.1.

CP-1000E Remote Control Panel

The CP-1000E is a fully programmable panel and therefore the operation of the panel is entirely
dependent upon its configuration. The CP-1000E has 16 physical buttons which offers up to 800
virtual buttons. The CP-1000E panel is ideal in applications where changes to sources and
destinations are needed regularly. For example, it could be used in OB trucks or other applications
where the user needs to pre-configure panels to suit different or recurring tasks.
See section 3.6 for more information on the operation of the CP-1000E Control Panel.

Figure 1-4: CP-1000E Control Panel

Revision 1.4

Page 3

Control Panel Series

1.2.2.

CP-2024E Remote Control Panel

The CP-2024E is a fully programmable panel and therefore the operation of the panel is entirely
dependent upon its configuration. The CP-2024E is a fully programmable panel and therefore the
operation of the panel is entirely dependent upon its configuration. The CP-2024E panel has 32
buttons laid out with a keypad section in the style of a traditional XY panel. The CP-2024E is ideal in
applications where changes to sources and destinations are needed regularly. For example, it could
be used in OB trucks or other applications where the user needs to pre-configure panels to
accommodate different or recurring tasks.
See section 3.7 for more information on the operation of the CP-2024E Control Panel.

Figure 1-5: CP-2024E Control Panel

1.2.3.

CP-2032E Remote Control Panel

The CP-2032E is a fully programmable panel and therefore the operation of the panel is entirely
dependent upon its configuration. The CP-2032E panel has 32 buttons laid out in two rows of 16
buttons. These panels are ideal in applications where changes to sources and destinations are
needed regularly. For example, it could be used in OB trucks or other applications where the user
needs to pre-configure panels to accommodate different or recurring tasks.
See section 3.8 for more information on the operation of the CP-2032E Control Panel.

Figure 1-6: CP-2032E Control Panel

Page 4

Revision 1.4

Control Panel Series

1.2.4.

CP-2048E Remote Control Panel

The CP-2048E is a fully programmable panel and therefore the operation of the panel is entirely
dependent upon its configuration. The CP-2048E features assignable and dynamic LCD button
technology. Each of the LCD buttons is capable of displaying multiple characters. The CP-2048E
panel has 48 buttons arranged in three rows of 16. These panels are ideal in applications where
changes to sources and destinations are needed regularly. For example, it could be used in OB trucks
or other applications where the user needs to pre-configure panels to accommodate different or
recurring tasks.
See section 3.9 for more information on the operation of the CP-2048E Control Panel.

Figure 1-7: CP-2048E Control Panel

Revision 1.4

Page 5

Control Panel Series

1.3.

XY/MULTI-BUS CONTROL PANELS

The XY/Multibus panels are panels with a variety of layouts. A wide range of panel operations including
XY and multi-destination may be configured using the router control system. Buttons can be
individually configured for any combination of source, destination, breakaway or control functions.
Features:
Buttons with high quality positive action
All panels are fully programmable to operate in a number of modes
Buttons can be programmed for breakaways
Program/Preview/Take mode can be programmed, emulating vision mixer operation, useful in
transmission environments
Optional Lock button protects against accidental or unauthorized selections
Camera joystick override on any eight GPI inputs, with momentary or latching action
1.3.1.

CP-2402E Dual Display Remote Control Panel

The CP-2402E is a fully programmable panel and therefore the operation of the panel is entirely
dependent upon its configuration. The CP-2402E is a versatile programmable panel with 29 illuminated
pushbuttons and two display windows. The CP-2402E is fully programmable and therefore the
operation of the panel is entirely dependent upon its configuration. It can be configured in a number of
different ways including XY or dual destination using the router control system. Each button can be
individually configured for any combination of source, destination, breakaway or control functions.
The physical button layout of the CP-2402E guides its configuration. For example, the left hand block
of 24 buttons can be programmed as sources. A number of these buttons can also be used for other
functions such as level selection, lock, prefix etc. The two display windows can be used to show the
current selected destination and the selected source. The two buttons located next to the display
windows can be used to scroll up or down through the source or destination list. The TAKE button
confirms the selection.

Figure 1-8: CP-2402E Remote Control Panel

See section 3.10 for more information on the operation of the CP-2402E Control Panel.

Page 6

Revision 1.4

Control Panel Series

1.3.2.

CP-3200E Remote Panel with Keypad and Display

The CP-3200E is a fully programmable panel and therefore the operation of the panel is entirely
dependent upon its configuration. The CP-3200E has a keypad panel normally arranged to operate as
an XY panel allowing control of any input or output, with up to four levels of breakaway. The CP-3200E
is normally used as a master XY panel in engineering or MCR type applications where access to any
input or output is required.
Advanced programming control enables the CP-3200E to be configured to control five destinations
without breakaway or a single destination with up to eights levels of breakaway. It has XY mode with
up to eight levels of breakaway, Five destination mode with a TAKE button for each destination but
without breakaways, and single destination mode with up to eight levels of breakaway. It also features
a 24 + 6 button keypad for source and destination names, for which source names can be up to seven
characters long and destination names can be up to eight characters long. The CP-3200E also has in
use displays for all four levels plus preset.

Figure 1-9: CP-3200E Control Panel

See section 3.11 for more information on the operation of the CP-3200E Control Panel.
1.3.3.

CP-3208E Remote Control Panel

The CP-3208E is a fully programmable panel and therefore the operation of the panel is entirely
dependent upon its configuration. The CP-3208E is an eight destination control panel that can handle
up to 32 sources. It is ideal in applications such as monitoring or live operational areas, where several
destinations are to be controlled rapidly with a single button selection. The status of each destination
is visible at all times for increased operational confidence. It has eight high brightness, green LED
displays with up to seven character names that show the current source selected to each destination.
The CP-3208E features 32 buttons for source selection and eight TAKE buttons for the destinations.

Figure 1-10: CP-3208E Control Panel

See section 3.13 for more information on the operation of the CP-3208E Control Panel.

Revision 1.4

Page 7

Control Panel Series

1.3.4.

CP-6400E Remote Display Panel, XY Keypad

The CP-6400E is a fully programmable panel and therefore the operation of the panel is entirely
dependent upon its configuration. The CP-6400E is an XY panel ideal for larger applications above
64x64 but can be used with any size router. It is typically used as a master panel to control any input
or output, with up to eight levels of breakaway. Its extra large keypad and eight character names
provide great flexibility to name sources and destinations in larger systems. Flexible architecture
permits any key to be programmed to provide any function. It has a large keypad with 32 buttons and
eight character names on high brightness green LED displays

Figure 1-11: CP-6400E Control Panel

See section 3.14 for more information on the operation of the CP-6400E Control Panel.
1.3.5.

CP-6408E Remote Control Panels

The CP-6408E is a fully programmable panel and therefore the operation of the panel is entirely
dependent upon its configuration. The CP-6408E panel is a multi-destination panel for the control of
eight destinations. Up to eight levels of breakaway are supported. The LED displays give visible
readout of the current source status. The large keypad and eight character names provide great
flexibility to name sources and destinations in larger systems. Flexible architecture permits any key to
be programmed to provide any function.

Figure 1-12: CP-6408E Control Panel

See section 3.15 for more information on the operation of the CP-6408E Control Panel.

Page 8

Revision 1.4

Control Panel Series

2.

INSTALLATION

2.1.

ELECTRO STATIC DISCHARGE (ESD) PRECAUTIONS

All semiconductor devices are sensitive to ESD. To prevent any damage or
degradation on components of the product caused by ESD, observe these
precautions when installing or removing modules from the frame.

1. Discharge static from your body. Wear a grounded anti-static wrist or heel strap to discharge the
static voltage from your body.
2. Use a Safe Work Area. Avoid handling modules in areas that have a floor or work surface covering
capable of generating a static charge. Also nothing capable of generating or holding a static charge
should be allowed in the work area.
3. Handle ESD sensitive modules carefully. Do not slide modules over any surface. Do not touch
exposed connector pins. Pick-up modules by the edges of the modules, never by touching exposed
leads.
4. Transport and store sensitive components or assemblies in a static-protected bag or container.

2.2.

MOUNTING

The control panels are equipped with rack mounting rails and fit into a standard 19 1RU or 2RU rack
space. To securely fasten the frame to the equipment rack, make sure that all four mounting screws
on each mounting rail are tightened securely.
2.2.1.

Desk Top Mounting

A Desk Top mounting kit (DMK) is available that allows the panel to be separated from the electronics
using a 40 in (1m) ribbon cable. The panel thickness in the DMK configuration is only 1.4 in (35mm).
This configuration is ideal for mounting the control panel in consoles that are limited in the amount of
space available. Contact the Factory for information about the Desk Top mounting kit. Figure 2-1
shows a cross section of a control desk with a panel mounted in the Desk Top configuration.

Revision 1.4

Page 9

Control Panel Series

Cross section view of
Control Panel with Desk
Mount Kit added

Control Desk

1.4" (35mm)
to rack mount rail

40 in (1m)
Ribbon Cable

Cross section view of

Control Panel chassis with
Desk mount kit added

3.5" (89mm)
to rack mount rail
(not including connectors)

Figure 2-1: Desk Top Mounting Configuration

2.2.2.

Grounding and Bonding NEBS Applications

The NEBS compliant version of this equipment is to be connected to a

Common Bonding Network.

Page 10

Revision 1.4

Control Panel Series

2
2
3

Figure 2-2: NEBS Bonding System

This NEBS compliant version of the frame is provided with the following components to facilitate
connection to a common bonding network:
Item#
1
2
3

Description
M4 HEX Nut
#6 external tooth lock washer
Bonding Lug

Qty.
2
4
1

Table 2-1: Bonding Parts Included with NEBS Compliant Version

This equipment is to be installed in the telecommunication network facilities.

Provide a dedicated connection from a common bonding network to this equipment by
connecting a stranded AWG #6 (16 mm2) copper wire to the bonding lug provided.
When using insulated wire, strip 7/8 inch (2 cm) of insulation.
Bare conductors of the bonding wire must be coated with antioxidant before crimp connections
to the bonding lug are made.
Fasten the bonding lug to the equipment as shown in Figure 2-2. The ground lug must be
secured as shown using four star washers (to prevent anti-rotation of the nuts) and two M4
nuts. Tighten the nuts securely to provide a good bonding connection.

Revision 1.4

Page 11

Control Panel Series

2.3.

COOLING

The control panel is designed to cool using normal convection air currents. There are no fans in the
control panels. Adjacent equipment may be mounted immediately to the top and bottom of the unit.

CAUTION: To ensure adequate cooling, care should be taken to ensure that

the air inlets and exhaust openings on the sides of the unit are free of
obstructions.

2.4.

USE OF SHIELDED CABLES

2.5.

In order to maintain the electromagnetic (EMI) shielding integrity of the control

panel it is recommended that shielded cables be used to connect the signals to
the various modules wherever possible. For all ports using shielded cables
(Serial RS232/422, etc.) both ends of the shield must be grounded.

REAR PANEL CONNECTIONS

Figure 2-3: Rear Panel

The rear panel connections to the 1RU and 2RU panels are identical. The following sections provide
an overview of the connections.
2.5.1. Connecting the Panels using Q-link
All the frames and remote control panels are connected by a coaxial link called Q-link. This link uses
standard 75 video cable daisy-chained from frame to frame and panel to panel. Each end of the
link must be terminated in 75. A pair of connectors is fitted to the frames and the link looped
through them.
On frames with several Q-Link connectors the Q-Link-1 or Q-Link 1a/1b is always available. The
extra Q-link connectors are only supported when a CI-0004 module is installed onto the FU-0003
processor. Only one connector is fitted on the panels and a T-piece needed to tap off the Q-link. In
this way a panel can be removed from service and replaced without disrupting the link, even
temporarily.

Page 12

Revision 1.4

Control Panel Series

This daisy chain method ensures the best transmission quality of the control signals down the cable.
Short cuts that might save cable, such as running stubs to some panels, are not recommended as this
may cause data errors under certain circumstances. A total of 64 devices (V5 firmware) can be
supported, normally organized as 16 frames and 48 panels. Each unit connected to the Q-link has its
own address switch that is set up as part of the system setup.
In medium sized systems it may be more suitable to have several Q-Links on the master frame and to
wire off in different directions. This requires a CI-0004 module in the master router. Only routers of
32x32 and above have the extra BNC connectors to support a CI-0004.

Revision 1.4

Page 13

Control Panel Series

In larger systems the extra processing power of the SC-1000 is often required. This is a separate 2U
controller that supports an optional backup controller and backup PSU. The large number of Q-Links
allows a system to be split into physical areas such as vision control, audio, production, and
engineering.

As a system design guide the SC-1000 should be considered when the router grows above 128x128
single level or has more than 10-15 total Q-Link devices.
In large buildings or outside broadcast vehicles (OB trucks) the Q-Link system can be affected by
mains earth differences between physically remote areas. This causes currents to flow in the outer of
the Q-Link cable that can disrupt the Q-Link communications. To prevent this problem Quartz can
supply a SI-0004 Q-Link opto-isolator unit.

Page 14

Revision 1.4

Control Panel Series

In large buildings the SI-0004 would only be installed once a problem had been identified. In OB
trucks it is good practice to install an SI-0004 between the internal Q-Link and any external tail gate
or bulk head patch panels. Multiple SI-0004 units can be used where several external Q-Links are
required.

Revision 1.4

Page 15

Control Panel Series

2.5.2. RS232/422 Computer Port
The computer port connector on the rear of a remote control panel only functions if a CI-0003 module
is installed. Controlling the routing system through a panel computer port is possible but is not
recommended, these ports are only provided for stand-alone S7 panels i.e. CP-3200E-S7. All Quartz
products use the same pin-out for the serial D9 connectors. The wiring of the connectors is different
for RS232 and RS422.

The cable between the PC and the router (RS232) only needs to use TX, RX, and GND as shown
below.

2.5.3.

Connecting the Control Panels using Ethernet

The Router control panels are designed for connection using 10Base-T (10 Mbps), 100Base-TX (100
Mbps) Ethernet cabling systems. There are two Ethernet ports labelled ETHERNET A and ETHERNET
B, to provide for redundancy in the control system. As a result, either port may be used for connection
to the router frames without compromise. Straight-Through Ethernet cables may be used when
connecting the control panels to an Ethernet hub.
Straight-through RJ-45 cable can be purchased or can be constructed using the pinout information in
Table 2-2. A colour coded wiring table is provided in Table 2-2 for the current RJ-45 standards (AT&T
258A or EIA/TIA 258B colour coding shown).

Page 16

Revision 1.4

Control Panel Series

Also refer to the notes following the table for additional wiring guide information.

Pin
1

Pin #

Signal

EIA/TIA 568A

AT&T 258A or
EIA/TIA 568B

10BaseT
or 100BaseT

1
2
3
4
5
6
7
8

Transmit +
Transmit
Receive +
N/A
N/A
Receive
N/A
N/A

White/Green
Green/White or White
White/Orange
Blue/White or Blue
White/Blue
Orange/White or Orange
White/Brown
Brown/White or Brown

White/Orange
Orange/White or Orange
White/Green
Blue/White or Blue
White/Blue
Green/White or Green
White/Brown
Brown/White or Brown

X
X
X
Not used (required)
Not used (required)
X
Not used (required)
Not used (required)

Table 2-2: Standard RJ-45 Wiring Colour Codes

Note the following cabling information for this wiring guide:
Only two pairs of wires are used in the 8-pin RJ-45 connector to carry Ethernet signals.
Even though pins 4, 5, 7 and 8 are not used, it is mandatory that they be present in the cable.
10BaseT and 100BaseT use the same pins; a crossover cable made for one will also work with
the other.
Pairs may be solid colours and not have a stripe.
Category 5 cable must use Category 5 rated connectors.
Devices on the Ethernet network continually monitor the receive data path for activity as a means of
checking that the link is working correctly. When the network is idle, the devices also send a link test
signal to one another to verify link integrity.
10/100:

This Amber LED is ON when a 100Base-TX link is last detected. The LED is
OFF when a 10Base-T link is last detected (the LINK LED is ON). Upon powerup the LED is OFF as the last detected rate is not known and therefore defaults
to the 10Base-T state until rate detection is completed.

LN/ACT:

This dual purpose Green LED indicates that the control panel has established a
valid linkage to its hub, and whether the control panel is sending or receiving
data. This LED will be ON when the control panel has established a good link to
its supporting hub. This gives you a good indication that the segment is wired
correctly. The LED will BLINK when the control panel is sending or receiving
data. The LED will be OFF if there is no valid connection.

The control panel has a specific IP address that must be set using the shaft encoder and dot matrix
display on the rear panel, or by using the Engineering menu on the DEBUG serial port. On panels with
front panel display capabilities, the IP address can also be set using a Setup front panel menu.

Please note that once a change to the control panels IP address is made, the change
in IP address DOES NOT become effective until the unit is power cycled.

Revision 1.4

Page 17

Control Panel Series

2.5.4. Debug RS-232 Port
The DEBUG connector provides an RS-232 serial control port used for loading firmware and providing
access to the Diagnostic menu. The wiring of the connector is the RS-232 pinout shown in Table 2-3.
Pin #
1
2
3
4
5
6
7
8
9

Name
TxD
RxD
Sig Gnd

Description
RS-232 Transmit Output
RS-232 Receive Input
RS-232 Signal Ground

Table 2-3: DEBUG Port Pin Connections

When building the cable; use a connector with a grounded metal shell, and a
shielded cable with the shield connected to the connector metal shell to prevent
RFI emissions from the equipment.

2.5.5. SERIAL RS232/422 Serial Ports

The SERIAL connector provides a RS-232/RS-422 serial control port. The wiring of the connectors is
different for RS-232 and RS-422 as shown in Table 2-4.
Pin #
1
2
3
4
5
6
7
8
9

Name
GND
TxD/TxRxD/Rx+
Sig Gnd
Sig Gnd
RTS/Tx+
CTS/RxGND

RS-232 Function
Chassis ground
Transmit Data Output
Receive Data Input
Signal Ground
Not used
Signal Ground
RTS Output
CTS Input
Chassis ground

RS-422 Function
Chassis ground
TX- Transmit Output
RX+ Receive Input
Receive Ground
Not used
Transmit Ground
TX+ Transmit Output
RX- Receive Input
Chassis ground

Table 2-4: SERIAL Port Pin Connections

When configured for RS-422 communications, the pinout is a standard SMPTE

207M RS-422 tributary pinout. When configured for RS-232 communications,
the pinout is similar to a DCE pinout, except for pin 5 which is not connected.

When building the cable; use a connector with a grounded metal shell, and a
shielded cable with the shield connected to the connector metal shell to prevent
RFI emissions from the equipment.

Page 18

Revision 1.4

Control Panel Series

2.5.6. Joystick Override
The Joystick or camera micro-switch override is provided as a standard feature on all control panels
and is accessed on the JOYSTICK port which is a male 9 pin D-type socket. When building a cable to
connect to the JOYSTICK port; use a tin and dimple type connector with an earthed metal shell, and a
shielded cable with the shield connected to the connector metal shell to prevent RFI emissions from
the equipment. The pin connections are:
Pin #
1
2
3
4
5
6
7
8
9

RS232 Function
Camera 1 Input
Camera 2 Input
Camera 3 Input
Camera 4 Input
Camera 5 Input
Camera 6 Input
Camera 7 Input
Camera 8 Input
Chassis ground

Table 2-5: JOYSTICK Port Pin Connections

It is possible for them to be mapped to any input by the customer. Also the destination controlled is
normally programmable to suit individual applications.
2.5.7.

Power

The power entry module contains a standard IEC 320 power inlet connector, two 5 x 20 mm fuse
holders, and an EMI line filter. The control panel comes with an auto-ranging power supply that
automatically senses the input voltage over the range of 100 to 240 VAC.
Power should be applied by connecting a three-wire, grounding-type power supply cord to the power
entry module on the rear panel of each power supply. For use in North America, the power cord
should be a minimum 18 AWG wire size; type SVT marked VW-1, maximum 2.5 m in length. For use
outside North America, use a power cord approved for the country of use with a minimum 1.00 mm2
wire size.

CAUTION: To reduce the risk of electric shock, grounding of the ground pin
of the main plug must be maintained.

For NEBS compliant installations, the AC power cord of the frame shall be
connected to an external surge protection device.

Revision 1.4

Page 19

Control Panel Series

An external 12 VDC input is provided to provide fully redundant powering of the unit. The DC input
connector is a 0.218 inch diameter center positive miniature DC power jack.

To connect the 12 VDC supply use an AC to DC converter rated at 12 VDC, 3 A minimum. A power
supply converter can be ordered from your Evertz Products dealer (Evertz part # VSHES34-120300).
The DC cable of the voltage adapter should be connected to the DC power jack on the rear panel.
The voltage adapter DC connector-fastening collar can be screwed to the DC power jack to prevent
accidental disconnection.

2.6.

CONFIGURING REMOTE CONTROL PANELS

The main setup or configuration, generated within the router control system, defines the way each
panel functions. However, there are a few functions set on the panels by the user.
There are generally two types of panels, those with intelligent LCD buttons and those without. All
panels have a multi-segment LCD display in the rear of the panel and a rotary shaft encoder. These
may be used to select a communications method (Ethernet or QLINK) and set the various addresses.
Additionally panels with intelligent LCD buttons can be set from the front panel using the LCD buttons.
These methods are described in the following sections 2.6.1 and 2.6.2.
2.6.1.

Configuring ANY Panel via the Rotary Shaft Encoder

The multi-segment display on the rear of the panel should be scrolling the current firmware revision.
To configure the panel for a specific communication method:
1. Turn the encoder until COMM is shown on the multi-segment display.
2. Once displayed, push in the encoder knob. The current communication method will be
displayed (either ENET or QLNK)
3. To select the method, push in the encoder knob again, and then turn the encoder to select
QLNK/ENET as desired. Once complete push in the encoder to select the item.
4. Turn the encoder knob to END, and then push in the encoder knob again. This will apply the
setting.
To set the QLINK Address:
1. Turn the encoder until QLAD is shown on the multi-segment display.
2. Push in the encoder knob to make your selection. The current QLINK Address is shown (a HEX
Value).
3. Push in the encoder knob to change the first value, then turn the encoder to select the value
you wish to use.
4. Press the encoder to move the cursor to the next digit and then press the encoder to select the
digit. Turn the encoder to select the value and then push in the encoder to apply the values.
5. Turn the encoder to END and press in the encoder knob to apply the settings.

Page 20

Revision 1.4

Control Panel Series

To set the IP Settings:
1. The following settings may be edited in the same manner as below:
a. IP Address (IPAD)
b. Subnet Mask (NETM)
c. DHCP enable or disable (1 or 0) (DHCP)
d. For more advanced IP configuration, such as gateways, the debug port must be used.
Please follow the instructions in sections 4.4.1 through 4.4.3 for connecting to the debug
port.
2. Scroll to the parameter to be configured (IE. IPAD), then click the encoder to select it.
3. The first four characters (including periods .) will be displayed, and the very first segment of
the display will have a cursor on the bottom.
4. Scroll the cursor to the character you wish to edit then push in the encoder to select it.
5. Turn the encoder to select the desired character then push in the encoder to save that value
and return to the cursor mode.
6. Repeat until all settings are correct and END is displayed. Push in the encoder on END to apply
the value.
2.6.2.

Configuring Intelligent LCD Button Panels via Front Panel LCD Buttons

If the panel has not yet been connected to a control system or a connection is NOT present (IE the
Ethernet or QLINK have been unplugged) then the panel will be in Comms information Mode and will
display information about the current version, Comms mode, and address information. There will also
be a setup button to enter the configuration mode. If the panel already has a configuration loaded and
is actively connected to a control system you may display this Comms Information Mode by
simultaneously pushing in and holding the bottom left most and bottom right most buttons for
approximately 10 seconds. At that time you can press setup to enter the configuration mode.
Once in setup mode, follow the instructions below to configure the panel for a specific communication
method:
1. Click on COMMS SETUP.
2. Next to the MODE control, ETHERNET or QLINK will be highlighted showing the current
selection. Click on method you wish to use.
3. Click save and reset.
Once in setup mode, follow the instructions listed below to set the QLINK Address:
1. Use the arrows next to ADDR to select a new value. The current value will be displayed.
2. Click save and reset.
Once in setup mode, follow the instructions listed below to set the IP Settings:
1. Click the value to edit (IP Setup, Mask Setup, Gate Setup) as the configuration is similar for
each item.
2. The page will change (i.e. Under IP Setup) to display IP= and the current IP value.
3. Choose the octet to edit. Use the up and down arrows to select the desired value.
4. Once all IP Settings are complete, click save and reset.

Revision 1.4

Page 21

Control Panel Series

3.

CONTROL PANELS AND OPERATION

Once the system has been fully installed the user can configure the control panels. This section
describes the standard control panels supplied and their operation, regardless of the router control
system in use.

3.1.

CONFIGURING PANELS

The router control system configuration application defines the precise operation of all control panels.
This allows the user to edit the system configuration that is stored. This file can then be downloaded
to the system. When the system powers up the configuration data is transferred to each panel as it
comes on-line.

3.2.

COMMON FEATURES OF ALL CONTROL PANELS

3.2.1. Buzzer Feature

The control panels are fitted with a buzzer to provide warnings when certain buttons are pressed. The
buzzer can be enabled or disabled by moving a link adjacent to the buzzer. See section 4.5.2 for
information on changing the buzzer control.
3.2.2. Joystick or Micro-switch Override
This feature is used for matching the colour balance of several cameras. Micro-switches in the
joysticks of the camera control units are pressed by the engineer conducting the line-up to select the
camera in use onto the line-up monitor. It overrides the current selection made on a remote panel.
When the micro-switch contact is released the override selection can revert to the previous selection
made on the conventional panel (momentary) or stay with the selected camera (latching). See section
0 for information on making connections to the JOYSTICK connector.
Each control panel can support up to eight cameras. The software configuration of the system
determines which inputs of the matrix are selected by the joystick contacts. Normally the joystick only
selects video, but there is in fact no limitation placed by the system and any level may be selected.
1. Press and hold the joystick to make an override selection.
2. Release the joystick to return to the previous selection made by the panel.
3. If two or more joystick buttons are pressed, they queue or stack with the last press taking
priority.
3.2.3. Computer Port
Currently not supported.

Page 22

Revision 1.4

Control Panel Series

3.3.

CONTROL PANEL TYPE: CP-1604E

This panel has 20 buttons and each button is programmable from the router control system to act as
either a source, destination, level, or lock/enable, or many other button types.

Figure 3-1: CP-1604E Control Panel

The destination and the levels controlled by this panel are determined by the setup of the system and
can be changed using the router control system.
3.3.1.

Sources Button

Press the required source button to select a new source.

If the Enable mode is active then you must press and hold the ENABLE button while you press the
source button. This protects against accidental selection of a route.
If Lock mode is enabled then the lock button toggles between the locked and unlocked state. First
select the route then press the LOCK button to protect the selection.

3.4.

CONTROL PANEL TYPE: CP-3201E

This panel uses LED buttons with re-legendable caps and status indication. There are 40 switches
which can be used for the selection of sources, destinations, breakaways and lock functions.

Figure 3-2: CP-3201E Control Panel

There are many modes in which the panel can operate, determined by the setup of the system. Some
examples are:

16x16 XY with breakaways and lock

32x1 with breakaways and lock
32x2 with a row of buttons for each destination and with breakaways and lock
32x8 XY without breakaway or lock

Revision 1.4

Page 23

Control Panel Series

The destination and the levels controlled by this panel are determined by the setup of the system and
can be changed using the router control system. In this way the buttons are re-configurable so any of
the buttons can perform any function. The generic operation below covers all the facilities which can
be used, but please note they may not all be available, because if it is set up as a 32 x 8 XY panel
there are no buttons left for lock or breakaway functions.
3.4.1.

Destinations

Press one of the destination buttons to choose a new destination. Its button then lights up to confirm
the selection and a source button is illuminated to show the currently selected source.
3.4.2.

Sources Button

Press the required source button to select a new source.

3.4.3.

Breakaways

Buttons may be configured, to enable breakaway selections of signal levels, such as video, audio 1,
audio 2 and time code.
If the breakaways are allowed, then normally all the level buttons light up denoting the married mode in
which all switching levels are switched simultaneously. If a breakaway selection is required then press
the buttons to deselect the levels which are not required to switch. Then press a source button to
choose a new source on the breakaway level.
If a breakaway is selected then source LEDs flash to denote that a breakaway condition exists. If all
four levels are selected to different source signals then three of the LEDs flash while the fourth is
steady. To find out which source LED corresponds to a particular signal level then select the desired
level (by deselecting the other levels) and the steady LED is the source selected on that level of the
matrix.

3.4.4.

Note that if more than one level is lit then the steady LED corresponds to the leftmost lit level button.

Lock Button

This button allows you to protect a route that you have selected. The lock mode can be configured to
function in several ways but, by default, it locks its own panel independently for each destination.
Press the LOCK button once to lock the route/panel. The button illuminates to show that the panel is
locked.
Press the button again to unlock the route/panel.
The panel remembers the lock status so that when a destination is locked and this destination is
reselected then the lock button will light up to show that this destination is locked.

Page 24

Revision 1.4

Control Panel Series

3.5.

CONTROL PANEL TYPE: CP-6401E

This panel uses LED buttons with re-legendable caps and status indication. There are 80 switches
that can be used for the selection of sources, destinations, breakaways, and lock functions.

Figure 3-3: CP-6401E Control Panel

There are many modes in which the panel can operate, determined by the setup of the system. Some
examples are:
32x32 XY with breakaways and lock
64x1 with breakaways and lock
64x2 with a row of buttons for each destination and with breakaways and lock
64x8 XY without breakaway or lock
The destination and the levels controlled by this panel are determined by the setup of the system and
can be changed using the router control system. In this way the buttons are re-configurable so any of
the buttons can perform any function. The generic operation below covers all the facilities which can
be used, but please note they may not all be available because, for example, if it is set up as a 64 x 8
XY panel there are no buttons left for lock or breakaway functions.
3.5.1.

Destinations

Press one of the destination buttons to choose a new destination. Its button then lights up to confirm
the selection and a source button also lights up to show the currently selected source.
3.5.2.

Sources Button

Press the required source button to select a new source.

3.5.3.

Breakaways

Buttons may be configured to enable breakaway selections of signal levels, such as video, audio 1,
audio 2 and time code.
If the breakaways are allowed, then normally all the level buttons light up denoting the married mode in
which all switching levels are switched simultaneously. If a breakaway selection is required then press
the buttons to deselect the levels which are not required to switch. Then press a source button to
choose a new source on the breakaway level.

Revision 1.4

Page 25

Control Panel Series

If a breakaway is selected then source LEDs flash to denote that a breakaway condition exists. If all
four levels are selected to different source signals then three of the LEDs flash while the fourth is
steady. To find out which source LED corresponds to a particular signal level then select the desired
level (by deselecting the other levels) and the steady LED is the source selected on that level of the
matrix.
Note that if more than one level is lit then the steady LED corresponds to the left-most lit level button.
3.5.4.

Lock Button

This button allows you to protect a route that you have selected. The lock mode can be configured to
function in several ways but, by default, it locks its own panel independently for each destination.
1. Press the LOCK button once to lock the route/panel. The button lights up to show that the
panel is locked.
2. Press the button again to unlock the route/panel.
3. The panel remembers the lock status so that when a destination is locked and this destination
is reselected, then the lock button will light up to show that this destination is locked.

3.6.

CONTROL PANEL TYPE: CP-1000E

This panel has 16 active LCD buttons and each button is programmable to act in many different
modes, including source, destination, level, or lock/enable modes.

Figure 3-4: CP-1000E Control Panel

The destination and the levels controlled by this panel are determined by the setup of the system and
can be changed using the router control system.
3.6.1.

Sources Button

Press the required source button to select a new source. If the Lock mode is enabled then the lock
button toggles between the locked and unlocked state. First select the route then press the LOCK
button to protect the selection.

Page 26

Revision 1.4

Control Panel Series

3.7.

CONTROL PANEL TYPE: CP-2024E

This panel has 32 active LCD buttons and each button is programmable from the router control
system to act in many different modes, including source, destination, level, or lock/enable modes.

Figure 3-5: CP-2024E Control Panel

3.8.

CONTROL PANEL TYPE: CP-2032E

This panel has 32 active LCD buttons and each button is programmable from the router control system
to act in many different modes, including source, destination, level, or lock/enable modes.

Figure 3-6: CP-2032E Control Panel

3.9.

CONTROL PANEL TYPE: CP-2048E

This panel has 48 active LCD buttons and each button is programmable from the router control
system to act in many different modes, including source, destination, level, or lock/enable modes.

Figure 3-7: CP-2048E Control Panel

Revision 1.4

Page 27

Control Panel Series

3.10. CONTROL PANEL TYPE: CP-2402E
This panel uses LED buttons with re-legendable caps and status indication. There are 24 switches
which can be used for the selection of sources, destinations, breakaways and control functions, such
as salvoes. The two uncommitted display windows can be assigned to the functions of selecting the
sources or for selecting the destinations.

Figure 3-8: CP-2402E Control Panel

There are many modes in which the panel can operate, determined by the setup of the system. Some
examples are:
16x16 XY with breakaways and lock
32x1 with breakaways and lock
32x2 with a row of buttons for each destination and with breakaways and lock
32x8 XY without breakaway or lock
The destinations and the levels controlled by this panel are determined by the setup of the system and
can be changed using the router control system. In this way the buttons are re-configurable so any of
the buttons can perform any function. The generic operation below covers all the facilities which can
be used.
The assignment of the displays as either source selection or destination selection is achieved during
configuration.
3.10.1.

Destinations

Either of the two displays can be assigned to be used for selecting the desired destination. Using the
up/ down arrow keys, the desired destination is displayed on the one-line display. Subsequent
selection of a source, either using the second display and controls or, using an assigned source key,
will make the change. The source keys can be designated to be Select & Take or Select, in which
case the Take key is subsequently used to complete the change.
3.10.2.

Sources Button

Select the required source as the new source, either using an assigned source key or using a display
and the up/ down arrow keys.
3.10.3.

Breakaways

Buttons may be configured to enable breakaway selections of signal levels, such as video, audio 1,
audio 2 and time code.

Page 28

Revision 1.4

Control Panel Series

If the breakaways are allowed, then normally all the level buttons light up denoting the married mode in
which all switching levels are switched simultaneously. If a breakaway selection is required then press
the buttons to deselect the levels which are not required to switch. Then press a source button to
choose a new source on the breakaway level.
If a breakaway is selected then the source LEDs flash to denote that a breakaway condition exists. If
all four levels are selected to different source signals then three of the LEDs flash while the fourth is
steady. To find out which source LED corresponds to a particular signal level, select the desired level
(by deselecting the other levels) and the steady LED will be the source selected on that level of the
matrix.
Note that if more than one level is lit then the steady LED corresponds to the left-most lit level button.
3.10.4.

Lock Button

This button allows you to protect a route that you have selected. The lock mode can be configured to
function in several ways but, by default, it locks its own panel independently for each destination.
1. Press the LOCK button once to lock the route/panel. The button illuminates to show that the
panel is locked.
2. Press the button again to unlock the route/panel.
3. The panel remembers the lock status so that when a destination is locked and this destination
is reselected then the lock button will light up to show that this destination is locked.

3.11. CONTROL PANEL TYPE: CP-3200E

This panel uses a keypad with 20 keys to select sources and destinations and a green display to show
both in use and preset selections.
The keys may be labeled with the names of sources, destinations and breakaway levels printed onto
plain paper using a laser printer.
All of the buttons can be configured to operate in different ways, so the description that follows is
somewhat generalized and some of the button functions mentioned below may not be set up on your
panels.

Figure 3-9: CP-3200E Control Panel

Revision 1.4

Page 29

Control Panel Series

3.11.1.

Keypad

Source and destination names are entered using a single or two step process. The data is entered
into the preset lower section of the display. The first press selects the name of the source/destination
(e.g. CAM); subsequent presses selects the number (eg 12), to give the overall source name CAM12.
If an error is made in the selection, then press the CLEAR button. The names of the sources,
destinations and how they are assigned to physical inputs and outputs of the matrix is determined by
the setup of the system. Users are able to alter these names and their assignment.
3.11.2.

Clear

If an error is made during entry of names on the keypad, press the CLEAR button to clear the display.
3.11.3.

Destinations

To enter the destination, select MODE and press the left-hand button under the display; the LED in
this button lights up. Then select a new destination using the keypad. The name is built up in the lower
preset section of the display. When you are satisfied with the new destination exit the destination
select mode by pressing the button again, or by pressing the TAKE button. The new destination is
transferred to use the upper section of the display, alongside its current source selections.
3.11.4.

Sources Button

When you have left the destination select mode you can select the source. The source name is built
up in the display in the same way as the destinations.
3.11.5.

Take Button

When the desired source is selected into the preset section of the display, you can press the TAKE
button to make a cut to the new source.
3.11.6.

Breakaways

Four buttons are provided to enable breakaway selections of signal levels, such as video, audio 1,
audio 2 and time code. These buttons can be labeled to suit each application. The system setup
determines which buttons are active (ie. which breakaways are allowed). If breakaways are allowed,
then when a new destination is selected, all the level buttons light up denoting the audio-follow-video or
married mode in which all switching levels are switched simultaneously (this is the normal condition).
If a breakaway selection is required then press the buttons to deselect the levels which are not
required to switch.
3.11.7.

Lock Button

This button allows you to protect a route that you have selected. The LOCK button locks the panel or
other panels from making further selections. The lock mode can function in several ways; it is possible
to lock your own panel, or all other panels or even all panels. Furthermore, when you press the lock
button it can lock just the current destination or it can lock all destinations. The choice of lock modes
is set in the software configuration according to customer requirements.
1. Press the button once to lock the panel. The green display shows that the panel is locked.
2. Press the button again to unlock the panel.

Page 30

Revision 1.4

Control Panel Series

3.12. CONTROL PANEL TYPE: CP-3200E IN 5 BUS MODE
This panel is a standard CP-3200E configured so that it accesses five destinations, but with no
breakaway capability. It uses a keypad with 20 keys to select the sources and a green display to show
both in use and preset selections.
All of the buttons can be configured to operate in different ways, so the description that follows is
somewhat generalized and some of the button functions mentioned below may not be set up on your
panels.
3.12.1.

Keypad

Source names are entered using a single or two step process. The data is entered into the preset
lower section of the display. The first press selects the name of the source/destination (eg, CAM);
subsequent presses select the number (eg 12), to give the overall source name of CAM12. If an error
is made in the selection, then press the CLEAR button. The names of the sources and how they are
assigned to physical inputs and outputs of the matrix is determined by the setup of the system.
3.12.2.

Clear

If an error is made during the entry of names on the keypad, press the CLEAR button to clear the
display.
3.12.3.

Sources Button

Select the source using the keypad to build up the name in the preset display.
3.12.4.

Destinations

To select the preset source to a destination press one of the destination buttons under the display.
3.12.5.

Breakaways

There are no breakaways on this panel. The levels controlled (eg audio-follow-video) are determined
by the setup of the system.
3.12.6.

Lock Button

This button allows you to protect a route that you have selected. The LOCK button locks the panel or
other panels from making further selections. The lock mode can function in several ways; it is possible
to lock your own panel, or all other panels or even all panels. Furthermore, when you press the lock
button it can lock just the current destination or it can lock all destinations. The choice of lock modes
is set in the software configuration according to customer requirements.
1. Press the button once to lock the panel. The green display shows that the panel is locked.
2. Press the button again to unlock the panel.

Revision 1.4

Page 31

Control Panel Series

3.13. CONTROL PANEL TYPE: CP-3208E
This panel uses LED buttons with re-legendable caps and status indication. There are 32 switches
which can be used for the selection of sources, and 8 under the displays which are take buttons. The
7 character LED dot matrix displays show the current source routed to each of the 8 destinations, as
defined in the router control system.

Figure 3-10: CP-3208E Control Panel

The destination and the levels controlled by this panel are determined by the setup of the system and
can be changed using the router control system. In this way the buttons are re-configurable.
3.13.1.

Sources Button

Press the required source button to pre-select the source. The source button will illuminate. Press the
take button under the display for the required destination, the display will update with the new source
name. The take buttons can either leave the pre-selected source button ready for another take, or
clear it to prevent accidental changes.
3.13.2.

Lock Button

A lock button can be setup to allow you to protect the panel.

1. Press the LOCK button to lock the panel. The LOCK button illuminates to show that the panel is
locked.
2. Press the button again to unlock the panel.

Page 32

Revision 1.4

Control Panel Series

3.14. CONTROL PANEL TYPE: CP-6400E
This panel uses a keypad with 32 keys to select sources and destinations, and 3 green LED dot matrix
displays to show current destination and source in use and preset selections. The left hand block of 8
keys are normally used for breakaway/level selection.
The keys may be labeled with the names of sources, destinations and breakaway levels printed onto
plain paper using a laser printer.

Figure 3-11: CP-6400E Control Panel

All of the buttons can be configured to operate in different ways, so the description that follows is
somewhat generalized and some of the button functions mentioned below may not be set up on your
panels.
3.14.1.

Keypad

Source and destination names are entered using a single or two step process. The data is entered
into the preset lower section of the display. The first press selects the name of the source/destination
(for example CAM); subsequent presses select the number (eg 12), to give the overall source name
CAM12. If an error is made in the selection, then press the CLEAR button. The names of the sources,
destinations and how they are assigned to physical inputs and outputs of the matrix is determined by
the setup of the system. The router control system is available to allow users to alter these names and
their assignment.
3.14.2.

Clear

If an error is made during entry of names on the keypad, press the CLEAR button to clear the display.
3.14.3.

Destinations

To enter the destination select mode, press the button by the upper display; the LED in this button
lights up and the centre preset window becomes the destination preset display. Then select a new
destination using the keypad, the name is built up in the centre display. When you are satisfied with
the new destination, exit the destination select mode by pressing the button again. The new
destination is transferred to the in use upper section of the display, and the current source selection
updates.

Revision 1.4

Page 33

Control Panel Series

3.14.4.

Sources Button

When you have left the destination select mode you can select the source. The source name is built
up in the centre display in the same way as the destinations.
3.14.5.

Take Button

When the desired source is selected into the preset section of the display, you can press the TAKE
button to make a cut to the new source.
3.14.6.

Breakaways

Eight buttons are provided to enable breakaway selections of signal levels, such as video, audio 1,
audio 2 and time code. These buttons can be labeled to suit each application. The system setup
determines which buttons are active (ie which breakaways are allowed). If breakaways are allowed,
then when a new destination is selected, all the level buttons light up denoting the audio-follow-video or
married mode in which all switching levels are switched simultaneously. This is the normal condition. If
a breakaway selection is required then press the buttons to deselect the levels which are not required
to switch.
3.14.7.

Lock Button

This button allows you to protect a route that you have selected. The LOCK button locks the panel or
other panels from making further selections. The lock mode can function in several ways; it is possible
to lock your own panel, or all other panels or even all panels. Furthermore, when you press the lock
button it can lock just the current destination or it can lock all destinations. The choice of lock modes
is set in the software configuration according to customer requirements.
1. Press the button once to lock the panel. The green display shows that the panel is locked.
2. Press the button again to unlock the panel.

Page 34

Revision 1.4

Control Panel Series

3.15. CONTROL PANEL TYPE: CP-6408E
This panel uses a keypad with 24 keys to select sources and destinations and 9 green LED dot matrix
Displays. It can work as an 8 destination panel showing the current sources for 8 destinations and the
source preset selections. Alternatively it can work as an XY panel showing the status of 8 levels to the
currently selected destination. The middle block of 8 keys are normally used for breakaway/level
selection.
The keys may be labeled with the names of sources, destinations and breakaway levels printed onto
plain paper using a laser printer.

Figure 3-12: CP-6408E Control Panel

All of the buttons can be configured to operate in different ways, so the description that follows is
somewhat generalized and some of the button functions mentioned below may not be set up on your
panels.
3.15.1.

Keypad

Source and destination names are entered using a single or two step process. The data is entered
into the preset lower section of the display. The first press selects the name of the source/destination
(eg CAM); subsequent presses select the number (eg 12), to give the overall source name CAM12. If
an error is made in the selection, then press the CLEAR button. The names of the sources and
destinations and how they are assigned to physical inputs and outputs of the matrix is determined by
the setup of the system. The router control system is available to allow users to alter these names and
their assignment.
3.15.2.

Clear

If an error is made during entry of names on the keypad, press the CLEAR button to clear the display.
3.15.3.

Sources Button

The source name is built up in the source preset display.

3.15.4.

Take Button

When the desired source is selected into the preset section of the display, you can press one of the 8
TAKE buttons to the right of each source display.

Revision 1.4

Page 35

Control Panel Series

3.15.5.

Breakaways

Eight buttons are provided to enable breakaway selections of signal levels, such as video, audio 1,
audio 2 and time code. These buttons can be labeled to suit each application. The system setup
determines which buttons are active (for example, which breakaways are allowed). If breakaways are
allowed, then when a new destination is selected, all the level buttons light up denoting the audiofollow-video or married mode in which all switching levels are switched simultaneously. This is the
normal condition. If a breakaway selection is required then press the buttons to deselect the levels
which are not required to switch.
3.15.6.

Lock Button

This button allows you to protect a route that you have selected. The LOCK button locks the panel or
other panels from making further selections. The lock mode can function in several ways; it is possible
to lock your own panel, or all other panels or even all panels. Furthermore, when you press the lock
button it can lock just the current destination or it can lock all destinations. The choice of lock modes
is set in the software configuration according to customer requirements.
1. Press the LOCK button once to lock the panel. The green display shows that the panel is
locked.
2. Press the LOCK button again to unlock the panel.

Page 36

Revision 1.4

Control Panel Series

4.

SPECIFICATIONS

4.1.

POWER

Voltage:

Power:
Fuses:
Safety:
EMI/RFI:

4.2.

Auto ranging, 100 240 VAC, 50/60 Hz

or
12 VDC, 3A
40W
1 amps, 250 Volt time delay 5 x 20 mm. line and neutral
ETL Listed, complies with EU safety directives
Complies with FCC Part 15 Class A regulations
Complies with EU EMC directive

PHYSICAL

Height:
1RU Panels:

CP-1604E, CP-3201E, CP-1000E, CP-2402E

1.75 (45 mm) 1 RU standard rack height
2RU Panels:
CP-6401E, CP-2024E, CP-2032E, CP-2048E, CP-3200E, CP-3208E
CP-6400E, CP-6408E
3.5 (89 mm) 2 RU standard rack height
Width:
19 (483 mm) 19 Rack Mount
Depth:
3.5 (89 mm) not including connectors
Desk Top Mounting (Desk Mount Kit required)
Panel Depth:
1.4 (35 mm)
Chassis Depth:
3.5 (89 mm) not including connectors
Distance from Panel to Chassis: 40 (1m) max
Weight:
1 RU Panels:
3 lbs. (1.36 kg)
2 RU Panels:
4 lbs. (1.81 kg)
Operating Temp:
0-40C

4.3.

CONTROL

Serial:
Debug:
Joystick:
Ethernet:

RS232/422, D9 female
RS232, D9 female, firmware updates and debug
Parallel contact closure TTL Levels, D9 male, TTL levels
10/100 Base T, 2 x RJ45

Revision 1.4

Page 37

Control Panel Series

4.4.

UPGRADING THE FIRMWARE

4.4.1. Overview
The firmware in the control panel is contained on a FLASH EPROM. From time to time firmware
updates will be provided to add additional features to the unit.
You will need the following equipment in order to update the Firmware:
PC with available communications port. The communication speed is 115200 baud.
Straight-thru serial extension cable
Terminal program that is capable of Xmodem file transfer protocol. (such as HyperTerminal)
New firmware supplied by Evertz.
4.4.2. Terminal Program Setup
1. Connect the serial cable to the DEBUG connector on the rear panel.
2. Connect the 9 pin connector on the end of the serial update cable to the PCs RS-232
communications port.
3. Start the terminal program.
4. Configure the port settings of the terminal program as follows:
Baud
Parity
Data bits
Stop bits
Flow Control

115200
no
8
2
None

5. Power up the control panel unit.

4.4.3. Initiating Firmware Upgrade Mode from the Terminal Program
You may send commands to the control panel Boot monitor in order to upgrade the panel application
firmware.
7. Power up the control panel. After the unit powers up, a banner with the boot code version
information should appear in the terminal window. The cursor to the right of the word BOOT>
should be spinning.
For example:
EVERTZ MCF5272 MONITOR 2.4 BUILD 2 (66 MHZ)
COPYRIGHT 1997, 1998, 1999, 2000, 2001, 2002 EVERTZ MICROSYSTEMS LTD.
28F640BFHE FLASH DETECTED
BRD=CPE-MB
MODEL=BACPE-MB-CPE-MB-XX-REV2
PROD=CP-2048EE
FRAME=9000FR
MCF5272 COLD BOOT>

Page 38

Revision 1.4

Control Panel Series

8. The following is a list of possible reasons for failed communications:

Defective Serial Upgrade cable.

Wrong communications port selected in the terminal program.
Improper port settings in the terminal program. (Refer to step 4 for settings). Note that
HyperTerminal will not change port settings while connected. Click on HyperTerminals
Disconnect Button then click the Reconnect button to activate changes to the port settings.

9. While the cursor is spinning press the <CTRL> and <X> keys, this should stop the cursor from
spinning. The spinning prompt will only remain for about 5 seconds. You must press <CTRL-X>
during this 5 second delay. If the unit continues to boot-up, simply cycle the power and repeat this
step.
10. Hit the <ENTER> key on your computer once.
11. Type the word upgrade, without quotes, and hit the <ENTER> key once.
12. The boot code will ask for confirmation. Type "y", without quotes.
4.4.4. Uploading the New Firmware
13. You should now see a prompt asking you to upload the file.
14. Upload the *.bin file supplied using the X-Modem transfer protocol of your terminal program. If
you do not start the upload within 10 minutes the units Boot code will time out. You can restart the
upgrade process by power cycling the unit.
The control panel application firmware is contained in a bin file that will have a name similar to:
router_cp_e_1_4_2.bin
The version number usually follows the main file name (e.g. 2v0_1 is version 2.0 build 1).
15. The boot code will indicate whether the operation was successful upon completion of the upload.
For Example:
UPLOAD OKAY
MCF5272 COLD BOOT>

16. Power cycle the control panel.

Revision 1.4

Page 39

Control Panel Series

4.5.

SERVICING INSTRUCTIONS
CAUTION: These servicing instructions are for use by qualified service
personnel only. To reduce the risk of electric shock, do not perform any
servicing instructions in this section of the manual unless you are qualified
to do so.

4.5.1. Changing the Fuses

CAUTION: For continued protection against the risk of fire, replace only with
the same type and rating of fuse.
ATTENTION: Pour viter les risques dincendie, remplacer le fusible avec un
fusible de mme calibre.
The fuse holder is located inside the power entry module. To change the fuses, disconnect the line
cord from the power entry module and pull the fuse holder out from the power entry module using a
small screwdriver. The fuse holder contains two fuses, one for the line and one for the neutral side of
the mains connection. Pull out the blown fuse and place a fuse of the correct value in its place Use slo
blo (time delay) 5 x 20 mm fuses rated for 250 Volts with a current rating of 1 amp. Carefully reinsert
the fuse holder into the power entry module.
4.5.2. Enabling/Disabling the Buzzer
In order to disable the buzzer, you must remove the top cover of the panel and change a link inside
the unit. Disconnect the line cord from the power entry module and disconnect any DC power source
connected to the unit. Using a small Phillips screwdriver, remove the top cover of the unit. The
buzzer is a square device located in front of the two RJ-45 Ethernet connectors. Jumper J2, located
to the immediate right of the buzzer controls whether the buzzer will be active or not. To enable the
buzzer, move the link to the BUZZER position. To disable the buzzer move the line to the OFF
position. Replace the top cover and screws, and reinstall the unit into your system.

Page 40

Revision 1.4