BP - GS136-1 - Materials For Sour Service PDF

GS 136-1
MATERIALS FOR SOUR SERVICE

March 1997
Copyright The British Petroleum Company p.l.c.
Copyright The British Petroleum Company p.l.c.

All rights reserved. The information contained in this document is
subject to the terms and conditions of the agreement or contract under
which the document was supplied to the recipient's organisation. None
of the information contained in this document shall be disclosed outside
the recipient's own organisation without the prior written permission of
Manager, Standards, BP International Limited, unless the terms of such
agreement or contract expressly allow.
BP GROUP RECOMMENDED PRACTICES AND SPECIFICATIONS FOR ENGINEERING

Issue Date
Doc. No.
GS 136-1
March 1997
Latest Amendment Date
Document Title

(Upstream Applications)
(Replaces BP Engineering Std 153)
APPLICABILITY
Regional Applicability:
International
SCOPE AND PURPOSE

This BP Guidance for Specification Specifies all BP general requirements for materials for
sour service that are within its stated scope and is for use with a complementary
Specification to adapt it for each specific application. It covers materials requirements in
sour service dduties applicable to upstream conditions. It makes major reference to
NACE Standard MR0175. And EFC Publications The purpose of this BP Guidance for
Specification is to give appropriate recommendations on the choice of materials for sour
service applications offering economical safe practice.
AMENDMENTS
Amd
Date
Page(s)
Description
___________________________________________________________________
CUSTODIAN (See above for contact)
Materials Engineering
Issued by:-
Engineering Practices Group, BP International Limited, Research & Engineering Centre

Chertsey Road, Sunbury-on-Thames, Middlesex, TW16 7LN, UNITED KINGDOM
Tel: +44 1932 76 4067
Fax: +44 1932 76 4077
Telex: 296041
CONTENTS
Section
Page
FOREWORD .................................................................................................................... IV
1. INTRODUCTION .......................................................................................................... 1
1.1 Scope
1
1.2 Service Conditions...................................................................................................... 2
1.2.1 Definitions of Sour Service ............................................................................. 2
1.2.2 Associated Service Conditions ........................................................................ 3
2. MATERIALS FOR SOUR SERVICE ........................................................................... 3
2.1 General SSC Requirements......................................................................................... 4
2.2 General HIC/SWC Requirements................................................................................ 6
2.3 Pressure Vessels; Carbon, Carbon Manganese and Low-Alloy Steel............................ 8
2.4 Pressure Vessels; Austenitic/Duplex Stainless Steel and Internally Clad ..................... 8
2.5 Heat-Exchanger Tube Bundles; Carbon, Carbon Manganese and Low-Alloy
Steel
8
2.6 Heat-Exchanger Tube Bundles; Austenitic/Duplex Stainless Steel and Nickel
Base Alloys
8
2.7 Process Pipework; Carbon, Carbon Manganese and Alloy Steel.................................. 9
2.8 Process Pipework; Austenitic/Duplex Stainless Steel and Nickel Base Alloys .............. 9
2.9 Transmission Pipelines...............................................................................................11
2.10 Downhole Tubulars .................................................................................................11
2.11 Low Temperature Plant ...........................................................................................11
2.12 Valves
12
2.13 Rotating Machinery .................................................................................................13
2.13.1 General 13
2.13.2 Centrifugal Pumps .......................................................................................15
2.13.3 Reciprocating Compressors..........................................................................15
2.13.4 Centrifugal Compressors..............................................................................16
2.13.5 Rotary-Type Positive Displacement Compressors.........................................16
2.13.6 Lubrication, Shaft Sealing and Control Oil Systems......................................16
2.14 Instrumentation .......................................................................................................16
2.15 Bolting 17
2.16 Bellows 17
2.17 Metallic Overlays.....................................................................................................18
2.18 Sour Service with Chlorides.....................................................................................18
2.19 Sour Service with Alkalis/Amines ............................................................................18
3. FABRICATION AND REPAIR WELDING................................................................18
* 3.1 Approval of Heat-Treatment Procedure ..................................................................18
* 3.2 Possible Avoidance of PWHT for Carbon Steel Pipework.......................................18
3.3 Welding Procedure Qualification Tests ......................................................................19
4. IDENTIFICATION, STAMPING AND MARKING...................................................20
4.1 Hard Stamps..............................................................................................................20
* 4.2 Marking Paints, Crayons etc. ..................................................................................20
5. INSPECTION ................................................................................................................20
GS 136-1
PAGE i
APPENDIX A ....................................................................................................................22
DEFINITIONS AND ABBREVIATIONS ......................................................................22
APPENDIX B.....................................................................................................................23
LIST OF REFERENCED DOCUMENTS.......................................................................23
APPENDIX C ....................................................................................................................26
SCHEMATIC ILLUSTRATION OF HYDROGEN INTERNAL PRESSURE
EFFECTS
26
FIGURE C1 .......................................................................................................................26
SCHEMATIC ILLUSTRATIONS OF ASSOCIATED FAILURE MECHANISMS ........26
APPENDIX D ....................................................................................................................27
SULPHIDE STRESS CRACKING REGION GRAPHS (NACE MR0175).....................27
FIGURE D1 .......................................................................................................................27
SOUR GAS SYSTEMS ..................................................................................................27
FIGURE D2 .......................................................................................................................27
SOUR MULTIPHASE SYSTEMS .................................................................................27
APPENDIX E.....................................................................................................................28
SOUR SERVICE WITH CHLORIDES - REQUIREMENTS FOR 300-SERIES
AUSTENITIC STAINLESS STEELS.............................................................................28
APPENDIX F.....................................................................................................................30
SOUR SERVICE WITH CAUSTIC OR OTHER ALKALINE PROCESS FLUIDS .......30
F1. GENERAL REQUIREMENTS FOR CARBON STEEL EQUIPMENT....................30
F2. SOUR STREAMS CONTAINING POTASSIUM CARBONATE ............................30
F3. SOUR STREAMS CONTAINING AMINES............................................................30
FIGURE F1........................................................................................................................31
REQUIREMENTS FOR STRESS RELIEF OF FABRICATIONS FOR USE
WITH CAUSTIC SODA.................................................................................................31
APPENDIX G ....................................................................................................................32
SPECIFICATION FOR STEEL PLATE (Z QUALITY) .................................................32
G1. SCOPE 32
G2. DEFINITION...........................................................................................................32
G3. MATERIAL.............................................................................................................32
G3.1 Standards32
* G3.2 Process32
G3.3 Chemical Composition ...................................................................................32
G4. INSPECTION REQUIREMENTS FOR PLATE ......................................................33
* G4.1 Ultrasonic Examination ...............................................................................33
* G4.2 Through-Thickness Tensile Test..................................................................33
G5. WELD REPAIR OF PLATE ....................................................................................33
APPENDIX H ....................................................................................................................34
SPECIFICATION FOR HIC RESISTANT STEEL PLATE FOR SEVERE
HYDROGEN CHARGING SERVICE............................................................................34
H1. SCOPE 34
GS 136-1
PAGE ii
H2. MANUFACTURING REQUIREMENTS ................................................................34

H2.1 Standards34
H2.2 Process 34
H2.3 Heat Treatment..............................................................................................34
* H2.4 Chemical Composition ................................................................................34
H3. TESTING REQUIREMENTS..................................................................................35
* 3.1 Ultrasonic Examination..................................................................................35
H3.2 HIC/SWC Test ..............................................................................................35
H4. WELD REPAIR OF PLATE ....................................................................................35
APPENDIX J .....................................................................................................................36
SOUR SERVICE LIMITS FOR DOWNHOLE TUBULAR STEELS.............................36
J1 SCOPE
36
J2. BACKGROUND .......................................................................................................36
J3. LIMITS OF SOUR SERVICE FOR DOWNHOLE TUBULAR STEELS..................36
J3.1 SSC Domains..................................................................................................37
TABLE J1 ..........................................................................................................................38
SOUR SERVICE DOMAINS .........................................................................................38
FIGURE J1 ........................................................................................................................38
SOUR SERVICE DOMAINS FOR DESIGN OF DOWNHOLE TUBULAR
STEELS AGAINST SSC ................................................................................................38
GS 136-1
PAGE iii
FOREWORD
Introduction to BP Group Recommended Practices and Specifications for Engineering
The Introductory Volume contains a series of documents that provide an introduction to the
BP Group Recommended Practices and Specifications for Engineering (RPSEs). In
particular, the 'General Foreword' sets out the philosophy of the RPSEs. Other documents in
the Introductory Volume provide general guidance on using the RPSEs and background
information to Engineering Standards in BP. There are also recommendations for specific
definitions and requirements.
Value of this Guidance for Specification
This BP Specification clarifies certain requirements specified in NACE MR0175 and provide
guidelines for the choice of materials for sour service duty offering economy, safety and
reliability of operation. The use of this Specification to its users will be significantly enhanced
by their regular participation in its improvement and updating. For this reason, users are urged
to inform BP of their experiences in all aspects of its application.
Application
This Guidance for Specification is intended to guide the purchaser in the use or creation of a
fit-for-purpose specification for enquiry or purchasing activity.
Text in italics is Commentary. Commentary provides background information which supports
the requirements of the Specification, and may discuss alternative options. It also gives
guidance on the implementation of any 'Specification' or 'Approval' actions; specific actions
are indicated by an asterisk (*) preceding a paragraph number.
This document may refer to certain local, national or international regulations but the
responsibility to ensure compliance with legislation and any other statutory requirements lies
with the user. The user should adapt or supplement this document to ensure compliance for
the specific application.
Specification Ready for Application
A Specification (BP Spec 136-1) is available which may be suitable for enquiry or purchasing
without modification. It is derived from this BP Group Guidance for Specification by
retaining the technical body unaltered but omitting all commentary, omitting the data page and
inserting a modified Foreword.
Principal Changes from Previous Edition
This Guidance for Specification has transpired from the general updating and conversion to
the new 'Way Forward' style of BP Engineering Standard 153.
GS136-1
PAGE iv
Principal Changes from June 1990 Issue:(a)

(b)
(c)
(d)
(e)
(f)
Document retitled to reflect the broad scope of the document, which exceeds that of
NACE MR0175-94.
General editorial changes made to format.
Amendment made to meet latest issue of NACE MR0175-94.
Major modification of sections to reflect current understanding of sour service.
Appendices A, B, C, D, E, F, G and H amended and retitled.
Special new section and Appendix J added for downhole tubulars.
Feedback and Further Information

Users are invited to feed back any comments and to detail experiences in the application of BP
RPSE's, to assist in the process of their continuous improvement.
For feedback and further information, please contact Standards Group, BP International or
the Custodian. See Quarterly Status List for contacts.
GS136-1
PAGE v
1.
INTRODUCTION
1.1
Scope
1.1.1
This Specification specifies BP general requirements on materials of

construction for equipment handling fluids containing water and
hydrogen sulphide (sour environments). It makes major reference to
the NACE Standard MR0175-94, (subsequently referred to in this
document as the NACE Standard).
1.1.2
In-service hydrogen damage problems arising from wet hydrogen

sulphide (H2S) service fall into three main categories which are covered
in this Specification. These are as follows:(a)
Hydrogen Embrittlement Effects - Sulphide stress cracking

(SSC), a hydrogen embrittlement phenomenon, is cracking
caused by hydrogen diffusing into the steel when subject to
tensile stress.
Areas of high hardness are susceptible to damage and cracking is also
affected by the stress level, solution chemistry and type of material.
The main method used to prevent such cracking is to control material
hardness and, in some cases, stress level by heat treatment. This is
described in detail in this document.
(b)
Hydrogen Internal Pressure Effects - Hydrogen diffuses into the

material and collects at inclusions/other defects and produces an
internal pressure which results in blistering and/or various forms
of hydrogen induced cracking.
Damage can be seen in various forms depending upon type and location of
the inclusions present and the stress pattern. These forms include
blistering, hydrogen induced cracking (HIC), stepwise cracking (SWC) and
stress oriented hydrogen induced cracking (SOHIC). These types of
hydrogen damage are schematically shown in Appendix C.
The
differences between these forms of hydrogen pressure related cracking are
described in the text (Paragraph 2.2).
The main method used to prevent this type of cracking is to select a high
quality clean material and, in some cases, to reduce stresses by heat
treatment. This is described in detail in the text.
(c)
Cracking in Related Environments - These include hydrogen

damage in sour environments in the presence of chlorides,
cyanides, alkalis and amines. This Specification modifies and
extends, where necessary, the requirements of the NACE
Standard, providing additional guidance for materials in sour
service in the presence of these chemicals.
GS136-1
PAGE 1
The NACE Standard defines sour service in gas and in multiphase

systems and recommends materials which will not fail by SSC in sour
environments. However, it does not cover certain sour duties nor other
associated failure mechanisms in sour service.
1.1.3
This Specification introduces a new method of defining sour service

limits for the use of downhole tubulars and, as such, represents a
departure from the traditional NACE approach. This new approach is
also described in European Federation of Corrosion Document;
Guidelines on Material Requirements for Carbon and Low Alloy Steels
for H2S - Containing Oil and Gas field Service.
1.1.4
Note that this Specification does not cover all general requirements for
chloride, alkali or amine services without H2S, and should not be used
for such purposes, but does provide guidance on avoiding
environmental cracking.
1.1.5
This Specification defines the requirements for new sour service

equipment for oil fields, transmission lines and refineries and it is
applicable whenever the process design conditions are such that sour
service as defined within may be encountered.
1.1.6
Reference is made in this Specification to various items of equipment,

such as pressure vessels and pipework, for which specific BP
Specifications exist. The requirements of such Specifications apply in
all respects, except as modified by this Specification for sour service.
1.1.7
In some cases it may be possible to upgrade existing equipment so that

the requirements of this Specification are met. Advice on this should
be sought from BP.
1.2
Service Conditions
1.2.1
Definitions of Sour Service

The following apply for this Specification for all items of equipment
except downhole tubulars, for which separate definitions apply
(Paragraph 2.10):-
1.2.1.1
The NACE Standard MR0175-94 defines sour service as process

streams containing liquid water and H2S at concentrations and
pressures within the zones shown as SSC regions on the graphs in
Appendix D and as described in 1.3.1.1 and 1.3.1.2 of the NACE
Standard.
Sour gas Figure D1, shall be used for wet gas systems in conjunction
with 1.3.1.1 (NACE Standard). Sour gas multiphase Figure D2 shall
GS136-1
PAGE 2
be used for multiphase oil, gas and water systems in conjunction with
1.3.1.2 (NACE Standard).
The above definitions for sour services are accepted by BP for systems
with less than 10 mol % H2S. All systems with 10 mol % or more of
H2S are regarded as sour in this Specification.
For equipment which contains only liquid, Figure D2 shall be used,
using the pressure and H2S content of the gas at the point where it was
last in equilibrium with the liquid.
2.
1.2.1.2
Where the NACE Standard refers to total pressure, this shall be taken
to mean total design pressure in the context of this Specification.
1.2.2
Associated Service Conditions
1.2.2.1
In process streams when H2S concentrations vary, peak values shall be

used in the context of this Specification.
1.2.2.2
This Specification specifies certain additional requirements that apply

for sour service in the presence of chlorides, cyanides, alkalis and
amines. BP or a process design contractor will specify when these
service conditions are applicable.
1.2.2.3
For process plants, consideration shall be given to the transient

conditions which arise during such operations as catalyst presulphiding
and regeneration.

All materials for sour service as defined in this Specification shall comply fully with the
NACE Standard except as modified or extended below. To put the requirements into
context, modifications are divided into two main categories as follows:(a)
General Sour Service Requirements - this is further described under three

sections:(i)
(ii)
(iii)
(b)
General SSC requirements (2.1)

General HIC/SWC/SOHIC requirements (2.2)
Special requirements for specific product forms (2.3-2.17)
Related Sour Service Requirements - this is further described in two sections:(i)

(ii)
Sour Service with Chlorides (2.18)

Sour Service with Alkalis/Amines (2.19)
GS136-1
PAGE 3
2.1
General SSC Requirements

SSC occurs as a result of diffusion of atomic hydrogen into the material from the
corrosion reaction at the metal surface. For SSC to occur, a combination of tensile
stress, an environment containing H2S and a susceptible material is required.
2.1.1
The selection of materials for a particular sour duty shall take into
account:(a)
Requirements arising from 1.2.2.1 of this Specification.
(b)
Resistance to general corrosion.

The pH value of the process stream and the presence or absence of
corrodents such as oxygen, carbon dioxide, chlorides etc. are of particular
importance.
(c)
2.1.2
Mechanical properties, including low temperature requirements

where necessary, shall be given specific attention.
Materials shall be selected from those permitted in the NACE Standard.

In addition, two other materials which have been found resistant to
SSC may be employed. These are:(1)
Firth Vickers FV 520B in the overaged 620C (1148F)

condition with maximum hardness 318 HV10 (RC32).
(Section 3.8 precipitation hardening stainless steel - NACE
Standard).
(2)
Nimonic 90 (UNS N07090) in the following conditions:(a)
Solution annealed.
(b)
Solution annealed and age hardened to RC35 maximum.

Material in this condition is acceptable for general service.
(c)
Cold worked and age hardened to RC50 maximum.

Material in this condition is acceptable for springs.
(Section 4 Non-Ferrous Metals - NACE Standard).

2.1.3
All castings shall be suitably heat treated after any welding operation
has been performed, and this requirement also applies to the weld
GS136-1
PAGE 4
repair of defects, irrespective of size. ASTM A216 for carbon steel

castings, and ASTM A217 Grade CA 15 for 11-13% chromium steel
normally permits certain repairs to be made without subsequent stress
relief. However, the practice of leaving 'as welded' areas in castings for
sour service is unacceptable to BP. All casting repair welds shall be
heat treated as follows:(a)
Carbon and carbon manganese steels: Thermal stress relief.
(b)
Martensitic stainless steels e.g. 11-13% chromium steel: Reheat treat completely or double temper (see NACE Standard
Section 3.7 for details of both heat treatments).
(c)
Austenitic and duplex stainless steels: Solution anneal.
(d)
Austenitic nodular iron: Welding is not permitted.
2.1.4
BP will impose limits on the use of austenitic, martensitic and duplex

stainless steels in sour service with chlorides. These limits, and the
suitability of alternative materials for specific applications, shall be
sought from BP.
2.1.5
Where the process duty is such that a wet gas environment exists in one
part of a vessel and a multiphase (oil, gas, water) system exists in
another part of the same vessel, material of construction for the entire
vessel shall be suitable for the more severe sour gas conditions, unless
otherwise approved by BP.
2.1.6
High strength steels at high levels of stress such as internal bolting,

springs, bellows and parts of reciprocating compressors require specific
attention, as experience shows they are susceptible to SSC in lower
concentrations of wet hydrogen sulphide than indicated by the NACE
Standard definition of sour service. They shall comply with the NACE
Standard when in contact with any concentration of wet hydrogen
sulphide.
2.1.7
In refinery environments, it is necessary for the weld metal to comply

with the hardness criteria of NACE RP0472.
2.1.8
Nitrile (NBR) and hydrogenated nitrile (HNBR) elastomers are

acceptable for low levels of H2S. NBR has a maximum long term limit
of between 10 and 100 ppm, depending on seal geometry and
temperature. For HNBR these limits are between 100 and 1000 ppm.
For H2S levels up to 5%, FKM 'Viton' type fluoroelastomers, or TFEP

'Aflas' shall be employed. Above this, FFKM perfluoroelastomers
(Chemraz or Kalrez) shall be required. PTFE also has excellent H2S
GS136-1
PAGE 5
resistance; if this material is selected, account shall be taken of the fact

that plastics require different seal configurations to elastomers.
In all instances, elastomer selection shall take into account the complete
operating conditions to be encountered, i.e. temperature, pressure and
chemical environment. All non-metallic seal materials and seal
geometry shall be subject to approval by BP.
*
2.1.9
Details of component materials and the material condition shall be

subject to BP approval prior to manufacture.
2.2
General HIC/SWC Requirements

The forms of hydrogen internal pressure damage, illustrated in Figure
C1 are as follows:(a)
Hydrogen Blistering
This occurs where inclusions or voids are present in the metal. Atomic
hydrogen can diffuse to these locations and convert to molecular
hydrogen. Since molecular hydrogen cannot diffuse, the concentration
and pressure of hydrogen gas within the voids increases and may be
sufficient to cause yielding in the metal and produce a bulge. These voids
or inclusions are generally associated with non-metallic inclusions.
(b)
SWC or HIC
This is formed in steels by the propagation and linking up of small and
moderate sized laminar cracks in a step-like manner. As more hydrogen
diffuses into the steel, the areas around these laminar cracks become
highly strained and this can cause linking of the adjacent cracks to form
HIC/SWC in the through thickness direction between the individual planar
cracks.
(c)
SOHIC (Stress Oriented HIC)

In some cases, when metal is subject to stress, small laminar HIC cracks
become lined up in the through-thickness direction and step cracks form
between them hence the occurrence of SOHIC. Formation of this type of
damage is linked to particular locations which are susceptible to laminar
cracking and to the stress pattern. This is often found, though not
exclusively so, in weld heat affected zones.
SOHIC is a phenomenon resulting from a combination of two independent
forms of hydrogen damage; HIC and SSC. New generations of linepipe
steel are becoming available offering superior metallurgy with improved
strength. These materials, reported to be resistant to either HIC or SSC,
have been found to suffer from SOHIC in certain environments. In these
circumstances, hydrogen concentration within the lattice is not sufficient
to cause conventional HIC, but adequate to cause combination of
HIC/SSC in the presence of external stress, hence the occurrence of
SOHIC..
GS136-1
PAGE 6
2.2.1
In cases where hydrogen blistering, HIC/SWC or SOHIC may occur,

BP may specify steel with increased resistance to these cracking
mechanisms and this shall conform to the requirements of either
Appendix G or H, as specified by BP. Alternatively, carbon steel
internally clad with stainless steel may be specified.
2.2.2
Plate steels and pipes made from plate have a particular sensitivity to
HIC/SWC damage. The mechanism of cracking involves two main
aspects which need to be considered when assessing the possibility of
cracking; these are described as follows:(a)
Hydrogen diffusion
Hydrogen diffusion into the steel is affected by environmental and surface
conditions.
Environment; Hydrogen diffusion will be affected by the specific chemical
environment e.g. level of H2S, pH, CO2, cyanide. There is not an
established level of H2S in refinery environments below which cracking
will not occur. However, a level of 50 ppmw H2S in solution in the water
phase has been taken by some as a level above which special emphasis
should be placed. The presence of cyanides significantly increases
hydrogen permeation.
(b)
The material's susceptibility to hydrogen damage

The susceptibility of the metallurgical structure to hydrogen damage is
defined by several parameters as follows:Strength; Increasing strength leads to increasing susceptibility to
hydrogen damage. The maximum tensile strength for process vessel plates
as supplied and tested should not exceed 586 MPa (85,000 psi.).
Microstructure/Material Cleanliness; Optimum HIC/SWC resistance is
obtained by utilising a clean steel with a homogenous microstructure.
Experience in BP has shown that an improvement in performance can be
achieved by specifying Z quality steel. This quality should be suitable for
moderate severity environments and is specified in Appendix G.
For higher severity environments (H2S/cyanide) a special HIC/SWC
resistant grade may be specified. This involves very low sulphur,
phosphorus and sometimes inclusion shape control with Ca. This is
detailed in Appendix H. Some of these steels may have some susceptibility
to SOHIC, so it is recommended that there should be BP specialist
involvement in purchase of these steels.
Heat Treatment; Material should usually be supplied in the normalised
condition. However, some of the newer steels processed by TMCP to
ASTM 841 can give even better performance and may be utilised at the
approval of the purchaser.
GS136-1
PAGE 7
2.3
Pressure Vessels; Carbon, Carbon Manganese and Low-Alloy

Steel
2.3.1
Pressure vessels, including heat exchanger shells, channels and floating

heads, shall be stress relieved. Where hydrogen sulphide contents in
excess of 10 mol % are encountered, stress relief is mandatory in all
cases.
2.3.2
Stress-relieving heat-treatment procedures shall be as required by BP

Group GS 146-2 or BP Group GS 146-3.
2.3.3

requirements of Paragraph 2.2 are applicable.
2.3.4
All internal bolting subject to sour environments shall be selected to be

resistant to SSC (see 2.1.6 of this Specification).
2.4
Pressure Vessels; Austenitic/Duplex Stainless Steel and Internally

Clad
2.4.1
Pressure vessels in sour service constructed from materials other than

carbon, carbon manganese and low-alloy steels e.g. austenitic/duplex
stainless steels and internally clad vessels or other high alloy corrosion
resistant alloys shall be subject to BP specification or approval.
2.5
Heat-Exchanger Tube Bundles; Carbon, Carbon Manganese and

Low-Alloy Steel
2.5.1
Where tube end welding is specified, special fabrication procedures are

necessary. For carbon steel assemblies, in order to avoid high
hardnesses in the weld and heat affected zones, either PWHT shall be
applied or the tube sheet shall be faced with low carbon weld metal and
stress relieved prior to tube end welding. For low alloy steel
assemblies, PWHT of tube end welds to achieve adequate resistance to
SSC is difficult. In this case consideration should be given to
overlaying the tubesheet with an austenitic alloy such as Inconel 625.
Irrespective of the fabrication technique adopted, the welding
procedure qualification tests shall be in accordance with this
Specification and requirements of BP Group Specification 118-8.
2.6
Heat-Exchanger Tube Bundles; Austenitic/Duplex Stainless Steel

and Nickel Base Alloys
2.6.1
Tube bundles made from materials other than carbon, carbon

manganese and low-alloy steels, e.g. austenitic/duplex stainless steels
and nickel base alloys or other high alloy corrosion resistant materials
GS136-1
PAGE 8
shall be in accordance with BP Group Specification 118-8 and this

Specification.
2.7
Process Pipework; Carbon, Carbon Manganese and Alloy Steel
2.7.1
Fabricated pipework shall comply with the requirements of BP Group

Specification 118-5 and this Specification.
2.7.2
Carbon and carbon manganese steel pipework shall have a carbon

content of 0.23% maximum for plate, seamless pipe and forged fittings.
The CE shall be 0.43% maximum based on product analysis and shall
be calculated as:CE = C + Mn + Cr + Mo + V + Ni + Cu
6
5
15
2.7.3
EFW pipe shall be in the normalised heat treated condition.
2.7.4
All carbon steel pipework with a wall thickness greater than 19 mm will
require PWHT unless otherwise approved by BP. At thickness below
19 mm the welding procedure should be designed with the objective of
meeting the NACE Standard hardness criteria in the as-welded
conditions.
Careful control of the welding parameters will generally allow multi-pass tubular
butt joints to be completed in accordance with the NACE hardness criteria.
However, particular attention should be paid to joints involving forged fittings
since the actual CE values for these are often higher than for pipe. Welding
procedures should be qualified using materials representative of the maximum
supply CE value.
2.7.5

BP may specify steel with increased resistance to these cracking
mechanisms and this shall conform to the requirements of either
Paragraph 2.2, Appendix G or Appendix H as specified by BP.
Alternatively, carbon steel internally clad with stainless steel may be
specified.
2.7.6
Low alloy steel pipework in sour service shall be subject to PWHT

irrespective of pipe size or wall thickness.
2.8
Process Pipework; Austenitic/Duplex Stainless Steel and Nickel

Base Alloys
2.8.1
Fabricated pipework from austenitic/duplex stainless steel and nickel

base alloys shall comply with the requirements of BP Group GS 118-7
and this Specification. Hardness levels and any associated heat
GS136-1
PAGE 9
treatments shall be subject to NACE standard requirements unless

otherwise approved by BP.
GS136-1
PAGE 10
2.9
Transmission Pipelines
2.9.1
Pipelines and associated fittings will be subject to the requirements of

BP Group GS 142. On pipelines for sour service, all material
specifications shall be subject to approval by BP.
2.9.2
Production control tests using the method of NACE Standard TM0284

shall be carried out on all pipeline steels specified by BP as suitable for
sour service, to demonstrate that they are resistant to HIC. The
hydrogen charging solution and procedures for this test and the
acceptance criteria will be in accordance with Appendix H as specified
by BP. Other tests may be specified by BP for manufacturing
procedure qualification. Acceptance criteria for the test shall be subject
to approval by BP.
2.9.3
Full diameter pipe HIC/SWC/SOHIC testing may be required, details

of which shall be specified by BP.
2.9.4
The mill and site welding procedures shall be carried out as specified in
3.3 of this Specification.
2.9.5
The specific service environment which the pipeline will be subjected to

will be taken into account by BP when assessing the results of hardness
surveys. Requirements may vary for each particular project and will be
individually specified.
2.9.6
PWHT of field girth welds of pipelines is not required unless specified

by BP, in which case the specific provisions shall be subject to BP
approval.
2.10
Downhole Tubulars
Specific requirements for the selection of downhole tubular steels are

described in Appendix J and defined in Figure J1 and Table J1, taking
on board the significance of in-situ pH.
The recognition within BP that the use of NACE guidelines does not lead to
optimum downhole materials choice led to the development of these specific
requirements.
In some countries NACE is a legislative requirement for the selection of downhole
materials for sour service duty.
2.11
Low Temperature Plant
2.11.1
The use of carbon and low-alloy ferritic steels and weld metals
containing more than 1% nickel are not permitted for sour service as
defined by NACE Standard. However, where low temperatures are
GS136-1
PAGE 11
encountered, such steels and weld metals may be used subject to BP

approval, providing the formation of liquid water can be prevented at
all times.
This will not be a problem during operation at temperatures below the freezing
point of aqueous solutions of hydrogen sulphide, but special measures (e.g. drying
the process stream) may be required during start up and shut-down if sour gas and
water are present at ambient temperature.
2.12
Valves
2.12.1
For valves specified for sour service, material selection and fabrication
procedures shall be in accordance with the 1994 Edition of the NACE
Standard and this Specification.
2.12.2
All valve parts which can be contacted by the sour environment shall
conform to this Specification. Valve parts not subjected to sour
environment need not comply with this Specification. Items which are
not freely vented to atmosphere such as insulated and buried equipment
and bolts inside flange protectors etc., where leakage of the process
stream could subject the equipment to a sour environment, shall
conform fully to this Specification.
2.12.3
Where plated components are employed, the material on which the

plating is deposited shall conform with this Specification. The plating
employed shall be resistant to the environment. Cadmium and zinc
plating are unsuitable as these metals corrode readily when in contact
with hydrogen sulphide.
2.12.4
Structural welding and weld repair of any cast component in contact

with the sour environment shall be followed by PWHT. Repairs to
valve balls, gates, disks, plugs etc. shall always be subject to PWHT.
2.12.5
All valve springs, except as outlined in Paragraph 2.12.5, shall be made

from materials resistant to SSC. Acceptable spring materials are those
given in 8.3 of the NACE Standard and UNS N07090 in accordance
with 2.1.2 (2c) of this Specification.
2.12.6
For large springs where the cost of resistant materials is very high, and
where spring failure is not critical in terms of safety or production
losses, non-resistant materials, suitably protected from the environment,
may be proposed for approval. The use of the following coatings may
be considered:(a)
Flexible 2-pack epoxy paint formulation. The maximum service

temperature for this type of coating is 100C (212F).
GS136-1
PAGE 12
(b)
Aluminium metal spray plus sealer.
(c)
Coatings of the fluorinated polymer type applied by the fluidised

bed process.
Where coatings have been accepted the complete spring shall be

protected and special attention shall be given to the half coils at the
spring ends.
It should be recognised that protective coatings cannot provide long-term
protection against failure and this must be taken into account.
2.12.7
When bellows-sealed safety or relief valves discharge into a common

header or piping system, springs shall comply with Paragraph 2.12.5.
Where this is not the case, the springs of bellows sealed valves may be
provided in accordance with Paragraph 2.12.6 subject to approval.
2.12.8
Internal bolting in valves shall be in accordance with Paragraph 2.15

(see 2.1.6).
2.12.9
The packing selected shall be compatible with the stem material.

Uninhibited graphite or carbon-type packing is not acceptable.
2.13
Rotating Machinery
2.13.1
General
2.13.1.1
Sour service for rotating machinery shall be taken as defined in 1.2.1.1,

except for reciprocating compressors where the presence of any level
of H2S shall be defined as sour.
2.13.1.2
The materials selected and fabrication procedures employed shall

comply with this Specification.
2.13.1.2
Carbon and carbon manganese steel plate for fabricated compressor

casings shall be resistant to HIC and shall conform to either Appendix
G or Appendix H, as specified by BP.
2.13.1.3
All fabrication welds and repair welds shall be heat treated as follows:(a)
Carbon and carbon manganese steels: PWHT at 580/620C

(1076/1148F), other temperatures only as approved by BP.
(b)
Low alloy steels: PWHT details shall be subject to approval by

BP.
GS136-1
PAGE 13
(c)
Martensitic stainless steel (11-13% chromium steel): Re-heat

treat completely including double temper.
For certain welds, complete heat treatment is not possible and double
tempering treatment only is acceptable.
(d)
Austenitic stainless steels do not normally require PWHT.
(e)
Duplex stainless steels: subject to approval by BP.
2.13.1.4
Cast irons and ferritic ductile (nodular) iron e.g. ASTM A 395 are
unacceptable for pressure-retaining parts and for impellers etc. The use
of these materials for non-pressure, low-stressed components shall be
subject to approval by BP. Austenitic irons are also unacceptable for
pressure-retaining parts except as permitted by 2.13.2.2. None of these
materials shall be weld repaired.
2.13.1.5
All components such as internal bolting, springs, etc. shall comply with
the relevant parts of this Specification.
2.13.1.6
Shafts and piston rods in plain carbon, low and medium alloy and 1113% chromium steels shall be heat treated to minimise residual stresses,
and shall have a hardness not exceeding 248 HV10 (HRC22) and a
yield stress not exceeding 620 N/mm2 (90 000 lbf/in2).
2.13.1.7
Shafts in austenitic and duplex stainless steel shall be in the solution

annealed condition. Where 17 Cr. - 4 Ni precipitation hardening steel
is employed, it shall conform to the NACE Standard. Precipitation
hardened nickel alloy shafts shall be in accordance with Section 4 of the
NACE Standard.
2.13.1.8
The straightening of shafts after completion of machining shall not be

commenced without prior approval from BP.
2.13.1.9
Approval shall be obtained from BP before any attempt is made to

rectify machining errors by the application of metal coatings.
2.13.1.10
All associated equipment e.g. pressure vessels, pipework etc. shall

comply with this Specification.
2.13.1.11
All components in 11-13% chromium steel shall be double tempered

after either normalising or quenching, and unless stated otherwise as in
2.13.3.6 of this Specification the hardness shall be 248 HV10 (HRC22)
maximum in conformity with 3.7 of the NACE Standard.
GS136-1
PAGE 14
2.13.2
Centrifugal Pumps
2.13.2.1
Centrifugal pumps shall conform to BP Group GS 134-4 except as

modified by this Specification.
2.13.2.2
For centrifugal pumps only, austenitic nodular iron BS 3468 Grade SNi Cr. 20 2 or equivalent is acceptable in certain cases, subject to
approval by BP. Welding of this material, including repair welding, is
not permitted. All castings shall be proved sound by radiography, and
they shall be stress relieved at 620/670C (1148/1240F).
2.13.2.3
Shafts in plain carbon and low alloy steels shall be totally protected
from the process stream by corrosion-resistant sleeves, cap nuts (where
applicable) etc. Unprotected 11-13% chromium steel may be used only
where it has adequate corrosion resistance to the process fluid.
2.13.3
Reciprocating Compressors
2.13.3.1
For reciprocating compressors only, the service shall be regarded as

sour when the gas contains any level of H2S. In all such cases, the
materials and fabrication procedures shall be in accordance with this
Specification.
2.13.3.2
Reciprocating compressors shall conform to BP Group GS 134-6

except as modified by this Specification.
2.13.3.3
Piston rods shall be either 11-13% chromium steel or an alternative

material approved by BP.
2.13.3.4
The piston rods shall conform to 2.13.1.7 of this Specification.

However, the rods may be hardened in the region of the packings by
the surface induction hardening method.
2.13.3.5
Liners shall be resistant to the corrosive environment. Where cast iron

would be corroded, a suitable grade of austenitic cast iron may be
proposed for BP approval.
2.13.3.6
Valve plates, rings, channels, seats and stops shall be made from 1113% chromium steel, unless otherwise approved by BP. The maximum
hardness for these components shall be 300 HV10 (HRC30). The
double tempering requirement after normalising or quenching (see
2.13.1.11) still applies.
2.13.3.7
Valves involving flexing plates are not normally permitted. Exceptions

may be made as follows:-
(a)
As stated in 2.13.3.9.
GS136-1
PAGE 15
(b)
Where the valve plate stresses for the application proposed are
low enough to render SSC unlikely.
In both cases, BP approval shall be obtained.
2.13.3.8
Valve springs shall be in accordance with 8.3 of the NACE Standard

and 2.1.1 (c) of this Specification. The design stress shall not exceed
276 N/mm2 (40 000 lbf/in2).
2.13.3.9
Alternative materials and designs may be used for compressor valves,

where proof is submitted that they have given satisfactory service.
However, all changes in materials, fabrication procedures and design
shall be subject to BP approval.
2.13.4
Centrifugal Compressors
2.13.4.1
Centrifugal compressors shall conform to BP Group GS 134-5 except

as modified by this Specification.
2.13.4.2
Fabrication processes which result in cold-worked material, e.g.

riveting of impellers, shall not be employed unless prior approval has
been obtained from BP.
2.13.5
Rotary-Type Positive Displacement Compressors

Rotary-type positive displacement compressors shall conform to BP
Group GS 134-9 except as modified by this Specification.
2.13.6
Lubrication, Shaft Sealing and Control Oil Systems
2.13.6.1
Lubrication, shaft sealing and control oil systems shall conform to BP

Group GS 134-3 except as modified in this Specification.
2.13.6.2
All equipment in contact either with seal oil or gas which is sour as
defined in this Specification, e.g. vessels, pumps, piping, valves, etc.,
shall conform to this Specification as regards material selection and
fabrication procedures.
2.14
Instrumentation
2.14.1
Instrument piping shall be in accordance with the associated process

line specification.
2.14.2
Bellows, diaphragms, Bourdon tubes, items which cannot be heat

treated after welding, and components which cannot function in the
softened condition shall be fabricated from materials resistant to
GS136-1
PAGE 16
cracking in the hardened or non-heat-treated conditions as defined in

the NACE Standard. UNS N08825 and UNS N04400 have given
satisfactory service in certain environments, and may be proposed for
BP approval.
*
2.14.3
Compression fittings in type 316L stainless steel may be used. For

relatively high temperature and high chloride service BP may require
the use of more corrosion resistant alloys (refer 2.14.2).
2.15
Bolting
2.15.1
Bolting shall comply with the NACE Standard requirements when in

contact with any concentration of wet H2S (see 2.1.6 of this
Specification).
2.15.2
Ferritic steel bolts and nuts shall conform to Section 6 of the NACE
Standard.
2.15.3
Where austenitic stainless steel bolts and nuts are required, these items
shall be free from cold work; they shall be solution treated after thread
forming etc. as outlined as follows:(a)
Bolts shall be Class 1A of ASTM A 193 e.g. B8MA (Type 316

bolts solution treated after all cold work including thread
forming).
(b)
Nuts shall be of the 'A' suffix variety of ASTM A 194 e.g.

Grade 8MA (Type 316) solution treated after all hot or cold
working.
2.16
Bellows
2.16.1
Bellows shall comply with the NACE Standard requirement when in

contact with any concentration of wet Hydrogen Sulphide (see
Paragraph 2.1.6) of this Specification.
2.16.2
Austenitic stainless steels shall not be used for bellows, but material
selection may be made according to the process conditions from the
following:-
Alloy 825 (UNS N 08825)

Alloy 625 (UNS N 06625)
Alloy 400 (UNS N 04400)
Other materials may be proposed for approval by BP. The production

procedure shall comply with the requirements of the NACE Standard.
GS136-1
PAGE 17
2.17
Metallic Overlays
Explosively clad, roll bonded and fusion-bonded corrosion resistant
overlays such as austenitic stainless steels and nickel alloys are
considered to be effective barriers to the sulphide environment. Where
such overlays are employed the backing material need not conform to
this Specification.
2.18
Sour Service with Chlorides

Where chlorides are present in sour service, but where the chloride
level and pH etc. permit the use of austenitic stainless steels, Appendix
E of this Specification shall apply. Refer also to Paragraphs 2.1.3 and
2.15.3 regarding H2S limits for stainless steel.
2.19
Sour Service with Alkalis/Amines

For sour service in association with alkalis, amines or other alkaline
process fluids, the requirements of Paragraph 2.16.2 and Appendix F
shall apply as appropriate.
3.
FABRICATION AND REPAIR WELDING

In addition to the requirements of NACE Standard, the following shall apply to any
heat treatment associated with initial fabrication or repair welding.
3.1
Approval of Heat-Treatment Procedure

For equipment which is to be post-weld heat treated, the following
information shall be submitted to BP for approval:-
3.2
(a)
Details of the method of heating, e.g. furnace, electric

resistance, induction, etc.
(b)
Details of the position of thermocouples.
(c)
Special requirements for heat-treatment, e.g. if it were proposed

to post-weld heat treat a heat-exchanger tube bundle
incorporating tube end welding.
(d)
Copies of relevant heat treatment charts on completion.
Possible Avoidance of PWHT for Carbon Steel Pipework

In order to avoid the need for PWHT on any part of a piping system,
the following requirements shall be met to the satisfaction of BP:-
GS136-1
PAGE 18
(a)
Standard welding procedures for all pipework shall provide for

a minimum of two passes.
(b)
The use of double sided welding on larger diameter pipe,

internal sealing runs to correct bore misalignment, internal root
repairs or the use of fittings requiring back welding, etc. will all
result in untempered weld beads on the process side. In such
cases the contractor or supplier shall either submit their
proposals for BP approval in accordance with 3.3, or shall
PWHT the welds concerned.
(c)
Pipework with wall thicknesses greater than 19 mm (0.750 in),

or on weldolets when the weld throat thickness exceeds 30 mm
shall be subject to PWHT as required by BP Group GS 118-5.
(d)
Where it is necessary to apply the requirements of Appendix F

of this Specification the above requirements are over-ruled.
3.3
Welding Procedure Qualification Tests
3.3.1
Prior to the commencement of work, the fabricator or supplier shall

submit to BP their proposals for qualifying the proposed welding
procedures, particularly related to the control of hardness.
3.3.2
In the case of 'as-welded' equipment the fabricator or supplier shall

submit to BP for approval the proposed method of meeting the
hardness limits of typical butt welds, internal sealing runs, branch welds
and local repairs etc. The hardness limits shall be subject to a
guarantee by the fabricator or supplier.
3.3.3
In the case of equipment which is to be post weld heat treated, the

welding procedure tests shall incorporate a hardness survey as specified
in 3.3.5 below.
3.3.4
On receipt of approval of the proposals, the contractor shall carry out

the agreed test welds and hardness surveys. The hardness surveys shall
be carried out on agreed samples cut from approved procedure test
coupons.
3.3.5
Test coupons shall be ground smooth and macro etched to reveal the
various zones of the weld. Hardness traverses shall be made at a
distance of 2 mm from the inner and outer surfaces of the welded joint
using the Vickers hardness test method with a load of 10 kg. The
hardness traverse shall include the parent metals, weld and weld heat
affected zones on both sides of the joint, and the positions of the
indentations shall be selected to establish peak hardness values. The
GS136-1
PAGE 19
maximum permitted hardness shall be in accordance with NACE

Standard requirements unless otherwise approved by BP (see also
paragraph 2.1.7).
*
3.3.6
4.
IDENTIFICATION, STAMPING AND MARKING

4.1
The results of the qualification tests plus welder qualifications shall be

submitted to BP for approval.
Hard Stamps
Conventional sharp 'V' stamping is acceptable only on the outer
circumferences of flanges. Round 'V' stamps may be used elsewhere,
providing the identities are placed on the external surfaces of low stress
areas. Where stamps have been inadvertently applied to high stress
areas, subsequent heat treatment is required.
4.2
Marking Paints, Crayons etc.

Conventional paints, crayons and adhesive tapes frequently used for
temporary marking during fabrication etc. may contain significant
amounts of chloride and heavy metals. Unless approved by BP, these
marking materials shall not be used on any stainless steel, and if used on
carbon or low alloy steels they shall be removed before heat treatment
(if applied) and before shipment if heat treatment is not required.
5.
INSPECTION
In addition to normal inspection, the following shall apply:
5.1
Documentation and inspection shall be provided to prove the identities

of all materials of construction and to establish that the correct heat
treatment has been applied so that the finished product complies fully
with this Specification. All material certificates shall be in accordance
with DIN 50049 3.1B or 3.1C as specified (BS EN 10204), or the
supplier may submit alternative proposals for approval by BP.
5.2
Where the hardness can be checked without damaging the component,

the manufacturer shall conduct hardness tests to ensure that the
hardness requirements of this Specification are met, and BP inspectors
will carry out random hardness checks. Where hardness values in
excess of the requirements of this Specification and the NACE
Standard are obtained the part shall be rejected. This requirement does
not apply to austenitic alloys supplied in the solution annealed
condition.
GS136-1
PAGE 20
5.3
For small items, e.g. small springs, pins etc. which cannot be hardness
tested individually, the manufacturer shall conduct tests on a random
basis by selecting components from production runs or stores batches
to ensure that the product complies fully with this Specification.
Procedures for doing this shall be subject to approval by BP. This
requirement does not apply to austenitic alloys supplied in the solution
annealed condition.
5.4
For welded components, hardness measurements can only realistically

be taken in weld metal and parent material. Acceptability of heat
affected zone hardness may be based on (i) welding procedure
qualifications tests and (ii) production test plates, when these are
required by the fabrication specifications.
5.5
For all corrosion resistant alloys, it shall be proved to the satisfaction of

the inspector that the specified heat treatment has been carried out
correctly.
GS136-1
PAGE 21
APPENDIX A
DEFINITIONS AND ABBREVIATIONS
Definitions
Standardised definitions may be found in the BP Group RPSEs Introductory Volume.
Abbreviations
API
ASTM
BS
CE
DEA
DIN
DIPA
EFC
EFW
FFKM
HIC
HNBR
HRC
HV
MEA
NACE
NACE Standard
NBR
NPS
PTFE
PWHT
SOHIC
SSC
SCC
SWC
TFEP
TMCP
American Petroleum Institute

American Society for Testing and Materials
British Standard
Carbon Equivalent
Di-Ethanolamine
Deutsche Institute for Normung
Di-Iso Propanol Amine
European Federation of Corrosion
Electric Fusion Welded
Perfluoroelastomers
Hydrogen Induced Cracking
Hydrogenated Nitrile Butadiene Rubber
Rockwell Hardness Scale C
Vickers Hardness
Mono-Ethanolamine
National Association of Corrosion Engineers
NACE Standard MR0175-94
Nitrile Butadiene Rubber
Nominal Pipe Size
Polytetrafluoroethylene
Post Weld Heat Treatment
Stress Orientated Hydrogen Induced Cracking
Sulphide Stress Cracking
Stress Corrosion Cracking
Step-wise Cracking
Tetro Flouro Ethylene Propylene
Thermo-Mechanical Controlled Processing
GS136-1
PAGE 22
APPENDIX B
LIST OF REFERENCED DOCUMENTS
A reference invokes the latest published issue or amendment unless stated otherwise.
Referenced standards may be replaced by equivalent standards that are internationally or
otherwise recognised provided that it can be shown to the satisfaction of the purchaser's
professional engineer that they meet or exceed the requirements of the referenced standards.
British Standards
BS 1501
BS 3468
BS 4360
BS 5996
BS EN 10164
Steels for Pressure Purposes : Plates, Part 1 - Specification for

Carbon and Carbon Manganese Steels
Austenitic Cast Iron
Weldable Structural Steels
Methods for Ultrasonic Testing and Specifying Quality Grades
for Ferritic Steel Plate
Steel Products with Improved Deformation Properties
Perpendicular to the Surface of the Product - Technical
Delivery Conditions
American Standards
NACE STD. MR0175-94
NACE STD TM0284-87
NACE STD TM0177-92
NACE RP 0472
ASTM A193
ASTM A194
ASTM A395
ASTM A516
ASTM A841
ASTM D1141-52
ASTM E140
API 614
Standard Material Requirements - Sulphide Stress Cracking

Resistant Metallic Materials for Oilfield Equipment
Test Method-Evaluation of Pipeline Steels for Resistance to
Stepwise Cracking.
Testing of Metals for Resistance to Sulphide Stress Cracking at
Ambient Temperatures.
'Methods and Controls to Prevent In-Service Environmental
Cracking of Carbon Steel Weldments in Corrosive Petroleum
Refining Environments'
Specification for Alloy-Steel and Stainless Steel
Bolting Materials for High Temperature Service
Specification for Carbon and Alloy Steel Nuts for Bolts for
High Pressure and High Temperature Service
Specification for Ferritic Ductile Iron Pressure - Retaining
Castings for Use at Elevated Temperatures
Specification for Pressure Vessel Plates, Carbon Steel for
Moderate and Lower Temperature Service
Specification for Steel Plates for Pressure Vessels, Produced by
the Thermo-Mechanical Control Process
Specification for Substitute Ocean Water
Standard Hardness Conversion Tables for Metals
Lubrication, Shaft-sealing and Control Oil Systems for Special
Purpose Applications
GS136-1
PAGE 23
API RP 945
DIN 50049 or
BS EN 1024; 1991
+ EFC Document
Guidelines for Avoiding Corrosion and Cracking Problems in

Amine Units
Materials Certificates or Metallic Products, Types
of Inspection Documents.
European Federation of Corrosion Document; Guidelines on
Material Requirements for Carbon and Low Alloy Steels for
H2S- Containing Oil and Gasfield Service.
+ Anticipated date of publication mid. 1995

BP Group Documents
BP Group GS 106-2
Painting of Metal Surfaces

(replaces BP Std 144)
BP Group GS 118-5
The Fabrication, Assembly, Erection and Inspection of Carbon,

Carbon Manganese and Low Alloy Ferritic Steel Pipework to
ANSI/ASME B31.3
(replaces BP Std 167 Part 1 and Part 2)
BP Group GS 118-7
Fabrication of Pipework to ANSI B31.3. Part 3: Austenitic and

Duplex Steel Pipework, Cupro-Nickel and Nickel Base Alloy
Pipework
(replaces BP Std 167 Part 3)
BP Group GS 118-8
Tube End Welding of Heat Exchanger Tubes

BP Group GS 134-3
Lubrication, Shaft-sealing and Control Oil Systems for Special

Purpose Applications to API 614
BP Group GS 134-4
Centrifugal Pumps to API 610

BP Group GS 134-5
Centrifugal Compressors to API 617

BP Group GS 134-6
Reciprocating Compressors to API 618

BP Group GS 134-9
Rotary Type Positive Displacement Compressors to API 619

BP Group GS 142-1 to 5)
Line Pipe and Fittings

GS136-1
PAGE 24
BP Group GS 146-2
Unfired Pressure Vessels to BS 5500

(replaces BP Std 194 Part 1)
BP Group GS 152-1
Materials for Thermal Insulation of Pipework and Equipment

GS136-1
PAGE 25
APPENDIX C
SCHEMATIC ILLUSTRATION OF HYDROGEN INTERNAL PRESSURE EFFECTS
Hydrogen Blistering
Hydrogen Induced Cracking (HIC)/Stepwise Cracking (SWC)
Stress Orientated Hydrogen Induced Cracking (SOHIC)
FIGURE C1
SCHEMATIC ILLUSTRATIONS OF ASSOCIATED FAILURE MECHANISMS
GS136-1
PAGE 26
APPENDIX D
SULPHIDE STRESS CRACKING REGION GRAPHS (NACE MR0175)
FIGURE D1
SOUR GAS SYSTEMS
FIGURE D2
SOUR MULTIPHASE SYSTEMS
(see 1.3.1.1 NACE document)
The above figures are reproduced by kind permission of the
National Association of Corrosion Engineers, Houston, Texas
GS136-1
PAGE 27
APPENDIX E
SOUR SERVICE WITH CHLORIDES - REQUIREMENTS FOR 300-SERIES
AUSTENITIC STAINLESS STEELS
E1.
Austenitic stainless steels shall be in the solution annealed condition.
E2.
Bends in pipework and tubing and other cold formed items shall be solution
annealed at 1050C (1920F) or stress relieved at 900/950C (1650/1740F) after
forming.
E3.
Austenitic stainless steels are not acceptable for bellows or other components in
the cold worked or highly stressed condition; note that 3.5.1 of the NACE
Standard prohibits the use of cold worked austenitic stainless steels. UNS N
08825 is an acceptable material among others for this duty. (See 2.16.2 for
alternatives).
*E4.
For welded equipment, stabilised or low carbon grades shall be used, and unless
otherwise approved by BP, all welded items shall be either solution annealed at
1050C (1920F) or stress relieved at 900/950C (1650/174F).
E5.
Attention is drawn to the fact that stress relieving heat treatments in the range 900950C usually result in a reduction in the notch toughness of ferrite containing
weldments. For this reason, when a PWHT is specified for pipework in low
temperature service, or when the piping code includes notch toughness
requirements, welding procedure tests should ensure that the PWHT does not
result in unacceptable embrittlement.
E6.
Because of the significantly greater risk of crevice corrosion in sour/chloride

service, the use of socket welded fittings, screwed couplings or any other weld
detail which could result in a crevice on the process side is not permitted.
E7.
Fusion-bonded overlays of Stellite or Colmonoy may be applied to stabilised or

low carbon grades of austenitic stainless steels, provided that the component is
subsequently heated rapidly to 900/950C (1650/1742F), held for 1 hour per 25
mm (1 in) of thickness and cooled in still air.
*E8.
Note that marine environments can often promote external chloride attack. In
such cases, the following shall apply:(a)
Austenitic stainless steels shall be protected externally if they are to

operate at temperatures between 40C (104F) and 120C (248F) in
chloride-containing environments, i.e. areas close to the sea.
(b)
Stainless steels for use in tropical marine areas, as specified by BP, shall
be protected externally before transporting to site and the protection
maintained during construction and operation at site. Protection of
GS136-1
PAGE 28
(c)
welds and associated heat-affected zones is most important. Any

painting specification used in the context of this Section shall be subject
to BP approval.
Thermal insulation of pipework and equipment shall be as required by
BP Group GS 152-1 and BP Group GS 106-2.
GS136-1
PAGE 29
APPENDIX F
SOUR SERVICE WITH CAUSTIC OR OTHER ALKALINE PROCESS FLUIDS
F1.
GENERAL REQUIREMENTS FOR CARBON STEEL EQUIPMENT

F1.1
Carbon steel is generally an acceptable material for handling certain caustic

soda and other alkaline solutions. However, it has limitations at higher
temperatures in that stress corrosion cracking can occur unless the
equipment is stress relieved, also unacceptable general corrosion can take
place.
F1.2
The stress relief requirements and upper temperature limits as given in

Figure F1 shall be applied, for carbon steel vessels and pipework in caustic
soda and other alkaline service. Stress relief shall be applied to the whole
vessel, and to welds, cold bends etc., in the case of pipework.
F1.3
The Designer shall make due allowance for general corrosion, which is not
taken into account in Figure F1.
General corrosion is significantly affected by increasing temperature.
F1.4
Where the particular caustic soda or other alkaline solution is at a

temperature in excess of that shown in Area B (Figure F1) material
selection shall be subject to approval by BP.
F1.5
Figure F1 shall apply to vessels and pipework only; material selection for
other equipment, e.g. pumps, shall be subject to approval by BP.
F2.
SOUR STREAMS CONTAINING POTASSIUM CARBONATE

F2.1
Some sweetening plants employ a potassium carbonate solution (normally

between 20% and 30% concentration) which can cause stress corrosion
cracking of welded carbon steel components. All welds in contact with such
fluids, whether in vessels or pipework, shall be stress relieved. A hardness
limit of 248 HV10 (HRC22) alone is not acceptable.
F3.
SOUR STREAMS CONTAINING AMINES
F3.1
To avoid stress corrosion cracking (SCC) of carbon steel welds exposed

to various amine solutions used in acid gas sweetening plants, stress
relieving of all welds is required as follows:MEA
DEA
DIPA
Other amine plants
Stress Relieved (SR) for all design temps.

SR above 140F (60C)
SR for all design temps.
SR above 82C (180F)
GS136-1
PAGE 30
Additional guidance on the avoidance of corrosion and SCC in amine

service, including licensed processes can be found in API RP 945. The
guidelines in API RP 945 shall be followed in all cases.
FIGURE F1
REQUIREMENTS FOR STRESS RELIEF OF FABRICATIONS FOR USE WITH
CAUSTIC SODA
GS136-1
PAGE 31
APPENDIX G
SPECIFICATION FOR STEEL PLATE (Z QUALITY)
G1.
SCOPE
This appendix defines the requirements to achieve enhanced resistance to wet H2S
service. It has been found by experience that steel made with enhanced through
thickness properties has improved resistance to hydrogen induced cracking. This type
of steel is known as 'Z' quality steel.
This type of steel was originally developed to prevent lamellar tearing in thick sections during
welding under conditions of high through-thickness stresses. However, the same requirements which
confer improved through-thickness properties also confer improved resistance to hydrogen induced
cracking.
G2.
DEFINITION
Z quality steel plate shall be designated as follows:BS 1501: 224 Grade 430 + EN 10164, Z35
G3.
MATERIAL
G3.1
Standards
The plate furnished by the supplier shall meet the requirements of BS
1501 or equivalent steel grades together with the following
supplementary requirements.
G3.2
Process
Steels shall be made by a low sulphur and low phosphorus refining
process, for example, in an electric furnace with double deslagging or in
the basic oxygen furnace (BOF). The steel shall be vacuum degassed
while molten by means of a BP approved process.
G3.3
Chemical Composition
The following supplementary requirements shall apply:Check Analysis %
0.20 max.
0.008 max.
0.025 max.
0.43 max.
Carbon
Sulphur
Phosphorus
Carbon Equivalent
The carbon equivalent values used in the above Table shall be

calculated by means of the formula defined in Paragraph 2.7.2 of this
Specification.
GS136-1
PAGE 32
The use of rare earth metals is not permitted.

G4.
INSPECTION REQUIREMENTS FOR PLATE
G4.1
Ultrasonic Examination
Material supplied in accordance with this specification shall be
ultrasonically tested in accordance with the requirements of BS 5996Grade LC3 or an equivalent approved by BP.
G4.2
Through-Thickness Tensile Test

Each plate shall comply with acceptance class Z35 of BS EN 10164 or
equivalent.
BP may agree to a retest after consideration of information supplied.
The through-thickness test shall be made after the completion of all
heat treatments.
In addition to the above, all the necessary tests required by the relevant
material specification shall be carried out.
G5.
WELD REPAIR OF PLATE
Weld repair of plate surface defects will not be permitted without BP approval and
shall be subject to an agreed repair procedure prior to the work being carried out.
GS136-1
PAGE 33
APPENDIX H
SPECIFICATION FOR HIC RESISTANT STEEL PLATE FOR SEVERE
HYDROGEN CHARGING SERVICE
H1.
SCOPE
This Appendix defines requirements for the manufacture and testing of steel plates
with maximum resistance to HIC/SWC for pressure vessels in severe hydrogen
charging environments e.g. sour water containing significant quantities of cyanides.
For less severe environments, as advised by BP, 'Z' quality plate may be specified, in
which case the requirements of Appendix G shall apply.
H2.
MANUFACTURING REQUIREMENTS
H2.1
Standards
Plates furnished by the supplier shall meet the requirements of BS
1501, ASTM A516, ASTM A841 or equivalent standards, together
with the requirements of this Appendix.
H2.2
Process
Steels shall be made by a low sulphur and low phosphorus refining
process, for example in an electric furnace with double deslagging or in
the basic oxygen furnace (BOF). The steel shall be vacuum degassed
while molten by means of a BP approved process.
H2.3
Heat Treatment
Plates for vessels shall be either normalised or TMCP.
H2.4
Chemical Composition
The following requirements shall apply:Check Analysis &
0.20 max.
0.002 max.
0.010 max.
0.003 max.
0.43 max.
Carbon
Sulphur
Phosphorus
Oxygen
Carbon Equivalent
The carbon equivalent values quoted in the above Table shall be

calculated using the formula defined in Paragraph 2.7.2 of this
Specification.
GS136-1
PAGE 34
Calcium treatment may be applied, but rare earth metals are not
permitted. For wet H2S service only, copper additions up to a
maximum of 0.35% are also permitted when specified by BP.
H3.
TESTING REQUIREMENTS
3.1
Ultrasonic Examination
Material supplied in accordance with this specification shall meet the
requirements of BS 5996 Grade L4 or an equivalent approved by BP.
3.2
HIC/SWC Test
Tests shall be made in accordance with NACE TM0284 in the NACE
TM0177 test solution. One set of 3 specimens shall be tested from
each thickness of plate from each heat. After testing, acceptance values
shall be 15% CLR (crack length ratio), 0.5% CTR (crack thickness
ratio) and 1.5% CSR (crack sensitivity ratio) unless otherwise agreed
with the purchaser. In marginal cases the supplier may request BP to
consider permitting a retest.
Following exposure, the test coupons shall be ultrasonically tested for
evidence of HIC/SWC in accordance with BS 5996 prior to sectioning.
Additional sections for microscopic examination shall be prepared
through any suspect locations, as approved by BP.
H4.
WELD REPAIR OF PLATE

Weld repair of plate surface defects will not be permitted.
GS136-1
PAGE 35
APPENDIX J
SOUR SERVICE LIMITS FOR DOWNHOLE TUBULAR STEELS
J1
SCOPE
This Appendix defines limits of sour service specific to downhole tubular steels. These
guidelines do not include downhole completion accessories for which the requirements
in the main body of this document apply.
J2.
BACKGROUND
The presence of H2S, CO2 and brine in wells not only give rise to increased corrosion
rates, but also can lead to SSC associated with enhanced uptake of hydrogen atoms
into the steel. Resistance to SSC is often the principal factor affecting the choice of
materials for H2S-containing environments, since the occurrence of SSC can result in a
catastrophic and potentially hazardous failure.
The occurrence of SSC requires a combination of tensile stress, an environment
containing H2S and a susceptible material. It follows that control of the problem may
be through manipulation of any or all of these parameters. It is apparent that factors
which promote hydrogen embrittlement would in turn affect the SSC behaviour of
steels. These include factors which influence hydrogen availability, entry and transport
within the metal lattice. Thus solution chemistry, as defined by its acidity, can
influence the performance of materials in sour environments. Solution acidity, i.e.
'in-situ pH', in the presence of sulphide ions (sour environments) increases the degree
of susceptibility to SSC.
Laboratory test results and the understanding of the mechanism of SSC have led to the
severity of the corrosive medium being expressed in the form of a pH - H2S partial
pressure diagram (see Figure J1)
In the context of the NACE MR0175 recommendation, it has been assumed that the presence of oil
favours the resistance to SSC. However, in such circumstances, there has never been a guarantee
against wetting of the steel surface by water or against the presence of very aggressive formation
waters. It is apparent, however, that the presence of oil in a production circuit is not sufficient to
ensure better resistance to SSC and a distinction between oil and gas production systems is
inappropriate. The good performance observed in the oil fields are believed to be the result of
complementary effects arising from the nature of water, the wetability or to the flow characteristic
and emulsion conditions. In this respect, it is important to base the definition of 'Sour Service' on the
analysis of the corrosive medium itself.
J3.
LIMITS OF SOUR SERVICE FOR DOWNHOLE TUBULAR STEELS

Bearing in mind the limitations of NACE MR0175, new limits of sour service have
been developed for a limited range of carbon and low alloy steels as well as corrosion
resistant alloys.
GS136-1
PAGE 36
The environmental variables used in obtaining qualitative SSC information have been
restricted to pH and H2S partial pressures, as these are believed to be the most
important parameters determining the SSC resistance of materials.
J3.1
SSC Domains
The limits of sour service have been plotted in graphs correlating
solution pH with H2S partial pressure in a domain relationship of the
type shown in Figure J1. The graph has been divided into three main
domains, each characterising the materials' suitability for sour service
applications with respect to SSC behaviour. These are as follows:(a)
Domain 1;
Designated as 'Non-Sour Service Domain' where
no special precaution is necessary when selecting the
completion tubing steels within those defined in Table J1.
(b)
Domain 2;
Designated the 'Transition Region' where in
addition to sour service grade materials, certain non-sour grades
can also be used (Table J1).
(c)
Domain 3;
Designated 'Sour Service Domain' which
characterise sour service conditions wherein H2S proved steels
to NACE Standard shall be utilised.
In pH/H2S partial pressure graphs, risk of SSC increases with

increasing H2S partial pressure and decreasing pH.
J4.
To apply the guidelines presented in this Appendix, it is necessary to know certain

information about the well including H2S partial pressure in the gas phase and the 'insitu' pH of the water associated with the produced fluid. Practical problems of
determining in-situ pH can be overcome by using a software program designated
CORMED.
J5.
Tendency of carbon and low alloy steels to other forms of corrosion attack have not
been covered in this Appendix.
J6.
Apart from SSC, tendency of corrosion resistant alloys to other types of failure should
be clarified. These include failure by chloride stress corrosion cracking (SCC), the
resistance to well treating chemicals and the tendency to hydrogen embrittlement
(HE), particularly for high strength duplex stainless steels.
GS136-1
PAGE 37
DOMAIN
DESIGNATION
SUITABLE GRADES
EXAMPLES
OF STEEL
Domain 1
Non Sour
Any Grades up to
Service
P110
- Carbon Steel Grade

P110
- 13% Cr. Grade N80
Domain 2
Domain 3
Transition
Strictly Controlled
Region
Grades and NACE

Approved Grades
- 13% Cr. Grade L80
Only Sour Service
Sour Service
Proved Grades

N80
L80
- Proprietary Grades
TABLE J1
SOUR SERVICE DOMAINS
FIGURE J1
SOUR SERVICE DOMAINS FOR DESIGN OF DOWNHOLE TUBULAR STEELS
AGAINST SSC
GS136-1
PAGE 38

BP - GS136-1 - Materials For Sour Service PDF

Uploaded by

Copyright:

Available Formats

BP - GS136-1 - Materials For Sour Service PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BP - GS136-1 - Materials For Sour Service PDF

Uploaded by

Copyright:

Available Formats

What is the document about?

What is the document about?

What are the three sour service domains?

What are the three sour service domains?

GS 136-1

MATERIALS FOR SOUR SERVICE

Copyright The British Petroleum Company p.l.c.

Copyright The British Petroleum Company p.l.c.

BP GROUP RECOMMENDED PRACTICES AND SPECIFICATIONS FOR ENGINEERING

Latest Amendment Date

MATERIALS FOR SOUR SERVICE

SCOPE AND PURPOSE

CUSTODIAN (See above for contact)

Engineering Practices Group, BP International Limited, Research & Engineering Centre

H2. MANUFACTURING REQUIREMENTS ................................................................34

Principal Changes from June 1990 Issue:(a)

Feedback and Further Information

This Specification specifies BP general requirements on materials of

In-service hydrogen damage problems arising from wet hydrogen

Hydrogen Embrittlement Effects - Sulphide stress cracking

Hydrogen Internal Pressure Effects - Hydrogen diffuses into the

Cracking in Related Environments - These include hydrogen

The NACE Standard defines sour service in gas and in multiphase

This Specification introduces a new method of defining sour service

This Specification defines the requirements for new sour service

Reference is made in this Specification to various items of equipment,

In some cases it may be possible to upgrade existing equipment so that

Definitions of Sour Service

The NACE Standard MR0175-94 defines sour service as process

Associated Service Conditions

In process streams when H2S concentrations vary, peak values shall be

This Specification specifies certain additional requirements that apply

For process plants, consideration shall be given to the transient

MATERIALS FOR SOUR SERVICE

General Sour Service Requirements - this is further described under three

General SSC requirements (2.1)

Related Sour Service Requirements - this is further described in two sections:(i)

Sour Service with Chlorides (2.18)

General SSC Requirements

Requirements arising from 1.2.2.1 of this Specification.

Resistance to general corrosion.

Mechanical properties, including low temperature requirements

Materials shall be selected from those permitted in the NACE Standard.

Firth Vickers FV 520B in the overaged 620C (1148F)

Nimonic 90 (UNS N07090) in the following conditions:(a)

Solution annealed and age hardened to RC35 maximum.

Cold worked and age hardened to RC50 maximum.

(Section 4 Non-Ferrous Metals - NACE Standard).

repair of defects, irrespective of size. ASTM A216 for carbon steel

Carbon and carbon manganese steels: Thermal stress relief.

Austenitic and duplex stainless steels: Solution anneal.

Austenitic nodular iron: Welding is not permitted.

BP will impose limits on the use of austenitic, martensitic and duplex

High strength steels at high levels of stress such as internal bolting,

In refinery environments, it is necessary for the weld metal to comply

Nitrile (NBR) and hydrogenated nitrile (HNBR) elastomers are

For H2S levels up to 5%, FKM 'Viton' type fluoroelastomers, or TFEP

resistance; if this material is selected, account shall be taken of the fact

Details of component materials and the material condition shall be