INTERNATIONAL TELECOMMUNICATION UNION

ITU-T

Q.711

TELECOMMUNICATION
STANDARDIZATION SECTOR
OF ITU

(07/96)

SERIES Q: SWITCHING AND SIGNALLING

Specifications of Signalling System No. 7 Signalling
connection control part

Functional description of the Signalling

Connection Control Part

ITU-T Recommendation Q.711

(Previously CCITT Recommendation)

ITU-T Q-SERIES RECOMMENDATIONS

SWITCHING AND SIGNALLING

SIGNALLING IN THE INTERNATIONAL MANUAL SERVICE

Q.1Q.3

INTERNATIONAL AUTOMATIC AND SEMI-AUTOMATIC WORKING

Q.4Q.59

FUNCTIONS AND INFORMATION FLOWS FOR SERVICES IN THE ISDN

Q.60Q.99

CLAUSES APPLICABLE TO ITU-T STANDARD SYSTEMS

Q.100Q.119

SPECIFICATION OF SIGNALLING SYSTEMS No. 4 AND No. 5

Q.120Q.249

SPECIFICATIONS OF SIGNALLING SYSTEM No. 6

Q.250Q.309

SPECIFICATIONS OF SIGNALLING SYSTEM R1

Q.310Q.399

SPECIFICATIONS OF SIGNALLING SYSTEM R2

Q.400Q.499

DIGITAL EXCHANGES

Q.500Q.599

INTERWORKING OF SIGNALLING SYSTEMS

Q.600Q.699

SPECIFICATIONS OF SIGNALLING SYSTEM No. 7

Q.700Q.849

General

Q.700

Message transfer part

Q.701Q.709

Simplified message transfer part

Q.710

Signalling connection control part

Q.711Q.719

Telephone user part

Q.720Q.729

ISDN supplementary services

Q.730Q.739

Data user part

Q.740Q.749

Signalling System No. 7 management

Q.750Q.759

ISDN user part

Q.760Q.769

Transaction capabilities application part

Q.770Q.779

Test specification

Q.780Q.799

Q3 interface

Q.800Q.849

DIGITAL SUBSCRIBER SIGNALLING SYSTEM No. 1

Q.850Q.999

PUBLIC LAND MOBILE NETWORK

Q.1000Q.1099

INTERWORKING WITH SATELLITE MOBILE SYSTEMS

Q.1100Q.1199

INTELLIGENT NETWORK

Q.1200Q.1999

BROADBAND ISDN

Q.2000Q.2999

For further details, please refer to ITU-T List of Recommendations.

ITU-T RECOMMENDATION Q.711

FUNCTIONAL DESCRIPTION OF THE SIGNALLING CONNECTION CONTROL PART

Summary
The Q.71X-Series of Recommendations define the services of the SCCP. The SCCP is part of
SS No. 7 and provides, above the MTP network or networks, connectionless, connection-oriented,
routing and management services.

Source
ITU-T Recommendation Q.711 was revised by ITU-T Study Group 11 (1993-1996) and was
approved under the WTSC Resolution No. 1 procedure on the 9th of July 1996.

Keywords
Broadband Integrated Services Digital Network (B-ISDN), Control plane (C-plane), Connectionless
Network Service (CLNS), Integrated Services Digital Network (ISDN), Message Transfer Part
(MTP) (of Signalling System No. 7), Network Node Interface (NNI), Network Service (NS),
Network Service Part (NSP) (of Signalling System No. 7), Signalling ATM Adaptation Layer
(SAAL), Signalling Connection Control Part (SCCP).

FOREWORD
ITU (International Telecommunication Union) is the United Nations Specialized Agency in the field of
telecommunications. The ITU Telecommunication Standardization Sector (ITU-T) is a permanent organ of the
ITU. The ITU-T is responsible for studying technical, operating and tariff questions and issuing
Recommendations on them with a view to standardizing telecommunications on a worldwide basis.
The World Telecommunication Standardization Conference (WTSC), which meets every four years,
establishes the topics for study by the ITU-T Study Groups which, in their turn, produce Recommendations on
these topics.
The approval of Recommendations by the Members of the ITU-T is covered by the procedure laid down in
WTSC Resolution No. 1.
In some areas of information technology which fall within ITU-Ts purview, the necessary standards are
prepared on a collaborative basis with ISO and IEC.

NOTE
In this Recommendation, the expression Administration is used for conciseness to indicate both a
telecommunication administration and a recognized operating agency.

INTELLECTUAL PROPERTY RIGHTS

The ITU draws attention to the possibility that the practice or implementation of this Recommendation may
involve the use of a claimed Intellectual Property Right. The ITU takes no position concerning the evidence,
validity or applicability of claimed Intellectual Property Rights, whether asserted by ITU members or others
outside of the Recommendation development process.
As of the date of approval of this Recommendation, the ITU had/had not received notice of intellectual
property, protected by patents, which may be required to implement this Recommendation. However,
implementors are cautioned that this may not represent the latest information and are therefore strongly urged
to consult the TSB patent database.

ITU 1997
All rights reserved. No part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from the ITU.

ii

Recommendation Q.711

(07/96)

CONTENTS
Page
1

Scope and field of application ....................................................................................

References ..................................................................................................................

2.1

Normative references ..................................................................................................

2.2

Informative references ................................................................................................

Definitions ..................................................................................................................

Abbreviations and acronyms ......................................................................................

General characteristics ................................................................................................

5.1

Technique of description ............................................................................................

5.2

Primitives ....................................................................................................................

5.3

Peer-to-peer communication .......................................................................................

5.4

Model of the connection-oriented network service ....................................................

5.5

Model of the connectionless network service .............................................................

5.6

Contents of the Q.71X-Series of Recommendations ..................................................

Services provided by the SCCP ..................................................................................

6.1

Connection-oriented services .....................................................................................

6.1.1 Temporary signalling connections ................................................................

8
8

6.1.2

Permanent signalling connections .................................................................

17

Connectionless services ..............................................................................................

6.2.1 Description ....................................................................................................
6.2.2 Primitives and parameters of the connectionless service ..............................

18
18
19

6.2.3

State transition diagram .................................................................................

22

6.3

SCCP management .....................................................................................................

6.3.1 Description ....................................................................................................
6.3.2 Primitives and parameters of the SCCP management ...................................

22
22
22

Definition of the lower boundary of the SCCP ..........................................................

25

7.1

MTP-SAP ...................................................................................................................

25

7.2

MTP-primitives and parameters .................................................................................

25

7.2.1
7.2.2
7.2.3
7.2.4

TRANSFER ..................................................................................................
PAUSE ..........................................................................................................
RESUME .......................................................................................................
STATUS ........................................................................................................

26
26
27
27

7.2.5

Notification of completion of MTP restart procedure ...................................

27

State transition diagram ..............................................................................................

27

6.2

7.3

Recommendation Q.711

(07/96)

iii

Page
8

Functions provided by the SCCP ...............................................................................

31

8.1

Connection-oriented functions ...................................................................................

8.1.1 Functions for temporary signalling connections ...........................................
8.1.2 Functions for permanent signalling connections ...........................................

31
31
31

8.2

Connectionless service functions................................................................................

32

8.3

Management functions................................................................................................

32

8.4

Routing and translation functions ...............................................................................

32

iv

Recommendation Q.711

(07/96)

Recommendation Q.711
FUNCTIONAL DESCRIPTION OF THE
SIGNALLING CONNECTION CONTROL PART
(revised in 1996)
1

Scope and field of application

The Signalling Connection Control Part (SCCP) provides additional functions to the Message
Transfer Part (MTP) to cater for both connectionless as well as connection-oriented network services
to transfer circuit related and non-circuit related signalling information and other types of
information between exchanges and specialized centres in telecommunication networks (e.g. for
management and maintenance purposes) via a Signalling System No. 7 network.
A functional block above the message transfer part performs the functions and procedures of the
SCCP. The SCCP is capable of using the services of the MTP as described in
Recommendations Q.701 to Q.707, and/or in Recommendation Q.2210. The combination of the MTP
and the SCCP is called "network service part" (NSP).
The network service part follows the principles of the OSI-reference model as defined in
Recommendation X.200, providing a subset of the layer 3 services defined in
Recommendation X.213.
It is the intent of Recommendations Q.711, Q.712, Q.713 and Q.714 to specify protocol entities
which perform the functions according to the SCCP of the Signalling System No. 7. These protocol
entities conform at their lower boundary to the upper boundary conditions specified in
Recommendation Q.704 or Q.2210 for use of the service offered by the underlying layers.
The SCCP making use of the services of the MTP, as specified in Recommendation Q.2210, provides
the connectionless network service as specified in this Recommendation. A connection-oriented
network service can only use the services which are common to Recommendations Q.2210 and
Q.704 for the MTP.
Recommendation Q.715 gives guidance on a number of specific issues related to the incorporation of
SCCP in actual networks. These guidelines are in their entirety informal and do not specify any
requirement.
The SCCP congestion control procedures may be subject to improvement pending further analysis of
the impact of these procedures in different network scenarios and based on the results of operational
experience. The overall objectives of the signalling connection control part are to provide the means
for:
a)
b)

logical signalling connections within the Signalling System No. 7 network;

a transfer capability for network service data units with or without the use of logical
signalling connections.

Functions of the SCCP are also used for the transfer of circuit related and call related signalling
information of the ISDN user part with or without setup of end-to-end logical signalling connections.
These functions are described in Recommendations Q.714 and Q.730. Figure 1 illustrates the
embedding of the SCCP within the Signalling System No. 7.

Recommendation Q.711

(07/96)

User part
type B

User part
type A

Other SCCP
user
(Note)
SCCP

MTP
T1157170-93

NOTE Interface using the signals as defined in 6.1.1.3.2, i.e. for the connection-oriented
network service.
The ISDN-UP that provides end-to-end signalling as defined in Recommendation Q.730 is
a type A user part.

Figure 1/Q.711 Functional diagram for the SCCP in Signalling System No. 7

References

The following ITU-T Recommendations and other references contain provisions which, through
reference in this text, constitute provisions of this Recommendation. At the time of publication, the
editions indicated were valid. All Recommendations and other references are subject to revision: all
users of this Recommendation are therefore encouraged to investigate the possibility of applying the
most recent edition of the Recommendations and other references listed below. A list of the currently
valid ITU-T Recommendations is regularly published.
The references contained in 2.1 and 2.2 contain the reference list for Recommendations Q.711,
Q.712, Q.713 and Q.714.
2.1

Normative references

CCITT Blue Book, Fascicle VI.7 (1988), Glossary of terms used in Signalling System No. 7.

ITU-T Recommendation Q.701 (1993), Functional description of the Message Transfer Part
(MTP) of Signalling System No. 7.

ITU-T Recommendation Q.704 (1996), Signalling network functions and messages.

ITU-T Recommendation Q.712 (1996), Definition and function of signalling connection

control part messages.

ITU-T Recommendation Q.713 (1996), Signalling connection control part formats and
codes.

ITU-T Recommendation Q.714 (1996), Signalling connection control part procedures.

ITU-T Recommendation Q.2210 (1996), Message transfer part level 3 functions and
messages using the services of ITU-T Recommendation Q.2140.

ITU-T Recommendation X.210 (1993), Information technology Open Systems

Interconnection Basic Reference Model: Conventions for the definition of OSI services.

Recommendation Q.711

(07/96)

2.2

Informative references

ITU-T Recommendation Q.700 (1993), Introduction to CCITT Signalling System No. 7.

ITU-T Recommendation Q.706 (1993), Message transfer part signalling performance.

ITU-T Recommendation Q.715 (1996), Signalling Connection Control Part user guide.

ITU-T Recommendation Q.716 (1996), Signalling Connection Control Part (SCCP)

performance.

ITU-T Recommendation Q.1400 (1993), Architecture framework for the development of

signalling and OA&M protocols using OSI concepts.

ITU-T Recommendation Q.2110 (1994), B-ISDN ATM adaptation Layer Service Specific
Connection Oriented Protocol (SSCOP).

ITU-T Recommendation Q.2140 (1995), B-ISDN signalling ATM Adaptation Layer

Service specific coordination function for signalling at the Network Node Interface (SSCF at
NNI).

ITU-T Recommendation X.200 (1994), Open Systems Interconnection Basic Reference

Model: The basic model.

ITU-T Recommendation X.213 (1995), Information technology Open Systems

Interconnection Network service definition (Note).
NOTE Further study is required to see which new parts of SCCP can use this Recommendation
normatively.

Definitions

Definitions of SCCP terms are provided in the glossary of CCITT Blue Book, Fascicle VI.7.
In addition to the definitions referenced, the following definitions apply:
3.1
An MTP-SAP instance is a logical point in the MTP network at which an MTP user can
access the services provided by the MTP-3 or the MTP-3b and the MTP can deliver its services to
the MTP user.
3.2
An SCCP-SAP instance is a logical point in the SCCP network at which an SCCP user can
access the services provided by the SCCP and the SCCP can deliver its services to the SCCP user.
4

Abbreviations and acronyms

This Recommendation uses the following abbreviations.

AAL
ATM
B-ISDN
B-ISUP

ATM Adaptation Layer

Asynchronous Transfer Mode
Broadband Integrated Services Digital Network
Broadband ISDN User Part (of SS No. 7)

DPC
ISUP
L3
LSB

Destination Point Code

Integrated Services User Part (of SS No. 7)
Level 3
Least Significant Bit

MSB

Most Significant Bit

Recommendation Q.711

(07/96)

MTP
MTP-SAP

Message Transfer Part

SAP to access the services provided by MTP

MTP-3
MTP-3b
NI
NNI

MTP Level 3 according to Recommendation Q.704

MTP Level 3 according to Recommendation Q.2210
Network Indicator
Network Node Interface

NPCI
NSDU
NSP
OPC

Network Protocol Control Information

Network Service Data Unit
Network Service Part
Originating Point Code

SAAL
SAP
SCCP
SCCP-SAP

Signalling ATM Adaptation Layer

Service Access Point
Signalling Connection Control Part (of SS No. 7)
SAP to access the services provided by SCCP

SDU
SI
SIO
SLC

Service Data Unit

Service Indicator
Service Information Octet
Signalling Link Code

SLS
SSCF
SSCOP
SS No. 7

Signalling Link Selection

Service Specific Coordination Function
Service Specific Connection Oriented Protocol
ITU-T Signalling System No. 7

STP
TUP
UP

Signalling Transfer Point

Telephone User Part (of SS No. 7)
User Part (of SS No. 7)

General characteristics

5.1

Technique of description

The Signalling Connection Control Part (SCCP) is described in terms of:

services provided by the SCCP;

services assumed from the MTP;
functions of the SCCP.

The functions of the SCCP are performed by means of the SCCP protocol between two systems that
provide the NSP service to the upper layers.
The service interfaces to the upper layers and to the MTP are described by means of primitives and
parameters, as recommended in Recommendation X.200. Figure 2 illustrates the relationship between
the SCCP protocol specification and the definition of adjacent services.

Recommendation Q.711

(07/96)

Network
service
definition
Reference to aims

SCCP
protocol
specification

Reference to assumptions

MTP
service
definition
T1157180-93

Figure 2/Q.711 Relationship between the SCCP protocol specification

and the definition of adjacent services

5.2

Primitives

Primitives define the information flow associated with the services requested of the SCCP and of the
MTP, see Figure 3.

Upper
layers
N-Service primitives
SCCP-SAP
Services of the SCCP

Service access
points (SAP)

Signalling
connection control
part

MTP-SAP
MTP-Service primitives

Services of the MTP

Service primitives
Message
transfer part
T1157190-93

Figure 3/Q.711 Service primitives

This diagram shows the points at which service primitives are invoked. It is not intended to constrain
the architecture. For the architectural considerations, some information is provided in
Recommendation Q.1400.

Recommendation Q.711

(07/96)

5.3

Peer-to-peer communication

Exchange of information between two peers of the SCCP is performed by means of a protocol. The
protocol is a set of rules and formats by which the control information (and user data) is exchanged
between the two peers. The protocol caters for:

the setup of logical signalling connection;

the release of logical signalling connections;

the transfer of data with or without logical signalling connections.

5.4

Model of the connection-oriented network service

A signalling connection is modelled in the abstract by a pair of queues. The protocol elements are
objects on that queue added by the origination SCCP user and removed by the destination SCCP
user. Each queue represents a flow control function. Figure 4 illustrates the modes described above.
Node A

Node B
User of the
network
service

User of the
network
service

Queue B to A

Queue A to B
T1157200-93

Figure 4/Q.711 Model for the internode communication with the SCCP
(connection-oriented services)

5.5

Model of the connectionless network service

This service definition uses the abstract model for a layer service defined in clause 5/X.210. The
model defines the interactions between the user and the provider of the connectionless network
service. These interactions take place at the two SCCP-SAPs (see Figure 5).
A defining characteristic of network-connectionless transmission is the independent nature of each
invocation of the connectionless network service. This basic service has been enhanced to provide
sequence integrity between SDUs (see protocol class 1 service).
The connectionless network service, as provided between SCCP-SAPs, can be modelled in the
abstract as a virtual transient association between the SCCP-SAPs (see Note).
NOTE This model is intended solely to describe the appearance of the connectionless-mode network service
to the SCCP users. It is not intended to be a model of the internal operation of the service provider in
providing the connectionless network service.

Only one type of object, the Unitdata, can be exchanged between the users of the service. This
relationship is illustrated in Figure 5.

Recommendation Q.711

(07/96)

Node X

Node Y

User of the
network
service

User of the
network
service

SCCP-SAP A

SCCP-SAP B

Virtual transient association between A and B

Service provider
T1178310-96

Figure 5/Q.711 Model of a network connectionless transmission

5.6

Contents of the Q.71X-Series of Recommendations

Recommendation Q.711 contains a general description of the services provided by the MTP, the
services provided by the SCCP and the functions within the SCCP.
Recommendation Q.712 defines the function of the messages, the set of protocol elements and their
embedding into messages.
Recommendation Q.713 describes the formats and codes used for the SCCP messages.
Recommendation Q.714 is a detailed description of the SCCP procedures as a protocol specification.
Recommendation Q.715 is the SCCP user guide. Implementation dependent aspects may be found in
Recommendation Q.715.
Recommendation Q.716 defines and specifies values for the SCCP performance parameters,
including quality of service parameters and internal parameters.
6

Services provided by the SCCP

The overall set of services is grouped into:

connection-oriented services;

connectionless services.

Four classes of service are provided by the SCCP protocol, two for connectionless services and two
for connection-oriented services.
The four classes are:
0
1
2
3

Basic connectionless class.

In-sequence delivery connectionless class.
Basic connection-oriented class.
Flow control connection-oriented class.

In the tables defining individual primitives, the notations given below are used:
M
indicates a mandatory parameter;
O
indicates an SCCP implementation option;
C
U

indicates that the parameter is conditional;

indicates a user option;

Recommendation Q.711

(07/96)

n.a.
=

not applicable;
indicates the parameter must have the same value in the indication primitive, or confirm
primitive as provided in the corresponding request primitive, or response primitive,
respectively.

6.1

Connection-oriented services

A distinction has to be made between:

temporary signalling connections;

permanent signalling connections.

Temporary signalling connections are under control (establishment, data transfer, release) of the
SCCP user. Further details are given in 6.1.1.
Permanent signalling connections are established and controlled by the local (or remote) maintenance
function or by the management function of the node and they are provided for the SCCP user on a
semipermanent basis. Further details are given in 6.1.2.
6.1.1

Temporary signalling connections

6.1.1.1

Description

The control of a signalling connection is divided into the following phases:

connection establishment phase;

data transfer phase;

connection release phase.

6.1.1.1.1

Connection establishment phase

Connection establishment procedures provide the mechanism for establishing temporary signalling
connections between users of the SCCP.
A signalling connection between two SCCP users may consist of one or more connection sections. A
signalling connection between two SCCP users in the same node is considered an implementation
dependent matter.
During connection establishment, routing functions are provided by the SCCP, in addition to those
provided by the MTP.
At intermediate nodes, SCCP routing determines whether a signalling connection should be realized
by one connection or by concatenated connection sections (i.e. coupling of connections). The criteria
for deciding on coupling are implementation dependent.
The ISDN UP may provide the routing of the request for the setup of a connection section
(see 6.1.1.3.2).
The connection refusal procedure is invoked if the SCCP or the SCCP user is unable to establish a
signalling connection.
6.1.1.1.2

Data transfer phase

The data transfer service provides for an exchange of user data, called Network Service Data Units
(NSDUs), in either direction or in both directions simultaneously on a signalling connection.

Recommendation Q.711

(07/96)

An SCCP message between two peers consists of:

Network Protocol Control Information (NPCI);

Network Service Data Unit (NSDU).

The network protocol control information supports the joint operating of the SCCP-peer entities
within the two nodes communicating with each other. It contains a connection reference parameter
which allocates the message to a certain signalling connection.
The network service data unit contains a certain amount of information from the SCCP user which
has to be transferred between two nodes using the service of the SCCP.
The network protocol control information and the network service data unit are put together and
transferred as a message (Figure 6). If the size of user data is too big to be transferred within one
message, user data are segmented into a number of portions. Each portion is mapped to a separate
message, consisting of the NPCI and an NSDU (Figure 7).
The data transfer service caters for sequence control and flow control depending on the quality of
service required by the SCCP user (two different classes of the connection-oriented service are
provided by the protocol; see Recommendation Q.714).

NPCI

NSDU

Message

T1157210-93

NPCI
NSDU
Message

Network Protocol Control Information

Network Service Data Unit
Protocol data unit

Figure 6/Q.711 Relation between NSDU and message

neither segmenting nor blocking

NPCI

NSDU

Message 1

Message 2
T1157220-93

Figure 7/Q.711 Segmenting

6.1.1.1.3

Connection release phase

Connection release procedures provide the mechanism for disconnecting temporary signalling
connections between users of the SCCP.

Recommendation Q.711

(07/96)

6.1.1.2

Network service primitives and parameters

6.1.1.2.1

Overview

Table 1 gives an overview of the primitives to the upper layers and the corresponding parameters for
the (temporary) connection-oriented network service. Figure 8 shows an overview state transition
diagram for the sequence of primitives at a connection endpoint. Refer to Recommendation X.213,
network service definition for open systems interconnection for ITU-T application.
A more detailed description for the primitives and their parameters is given in the following
subclauses.
Table 1/Q.711 Network service primitives for connection-oriented servicesb)
Primitives
Generic name

Parameters

N-CONNECT

Request
Indication
Response
Confirm

Called address
Calling address
Responding address
Expedited data selection
Quality of service parameter set
User data
Importance
a)
Connection identification

N-DATA

Request
Indication

Importance
User data
Connection identificationa)

N-EXPEDITED DATA

Request
Indication

User data
a)
Connection identification

N-DISCONNECT

Request
Indication

Originator
Reason
User data
Responding address
Importance
Connection identificationa)

N-RESET

Request
Indication
Response
Confirm

Originator
Reason
Connection identificationa)

a)
b)

10

Specific name

In 5.3/X.213, this parameter is implicit.

Only primitives described in Recommendation X.213 are present.

Recommendation Q.711

(07/96)

N-DISCONNECT
request, indication

N-DISCONNECT
request, indication

Idle

N-DISCONNECT

N-DISCONNECT

N-CONNECT
request
a)b)
REQUEST type 1

Outgoing
connection
pending

N-CONNECT
indication
a)b)
REQUEST type 2

Incoming
connection
pending

N-DISCONNECT
request, indication
REPLY

a)b)

N-CONNECT
response

N-CONNECT
confirm
Data transfer

N-RESET
indication

N-RESET
request

User requested
reset pending

N-RESET
confirm

N-CONNECT
indication b)

N-DATA
N-EXPEDITED DATA
a)
N-INFORM
(request, indication)

N-RESET
confirm

N-RESET
response

Provider initiated
reset pending
T1178320-96

N-DATA
N-EXPEDITED DATA
request, indication

a)
b)

N-DATA
N-EXPEDITED DATA
request, indication

This primitive is not in Recommendation X.213. (See 6.1.1.3.1.)

For user part type A only.

Figure 8/Q.711 State transition diagram for the sequence of primitives

at a connection endpoint (basic transitions)

6.1.1.2.2

Connection establishment phase

An SCCP user (calling user) initiates the setup of the connection by means of the primitive
"N-CONNECT request" to the SCCP. The SCCP entity evaluates the primitive and adds the protocol
control information. The SCCP message [consisting of the Protocol Control Information (PCI) and
possibly an NSDU] is transmitted by means of the MTP-services to the remote peer entity of the
SCCP. It evaluates and strips the PCI and sends a primitive "N-CONNECT indication" to the local
SCCP user. On both ends of the connection, the status "pending" is assumed.
The responding SCCP user answers with the primitive "N-CONNECT response" to the local SCCP,
which sends the response SCCP message including PCI to the calling SCCP. The calling SCCP
sends the primitive "N-CONNECT confirm" to the calling SCCP user. The connection is now ready
for data transfer.
The four types of N-CONNECT, the request, the indication, the response and the confirm contain the
parameters as shown and further described in Table 2.

Recommendation Q.711

(07/96)

11

Table 2/Q.711 Parameters of the primitive N-CONNECT

Primitive
Parameter

N-CONNECT
request

N-CONNECT
indication

N-CONNECT
response

N-CONNECT
confirm

Ma2)

n.a.

n.a.

c1)

n.a.

n.a.

n.a.

n.a.

a3)

Cc1)

Expedited data selection

n.a.

n.a.

Quality of service parameter

set

M(=)

User data

C(=)

Connection identification

Importance

Called address

a1)

Calling address

Responding address

b)

c1)

c1)

C(=)

a1)

This parameter is associated with the SCCP service access point at which this primitive is issued if the
calling address is absent.

a2)

This parameter is associated with the SCCP service access point at which this primitive is issued if the
called address is absent.

a3)

This parameter is associated with the SCCP service access point at which this primitive is issued if the
responding address is absent.

b)

In 5.3/X.213, this parameter is implicit.

c1)

If present in the received SCCP message.

The parameters "called address/calling address" convey addresses identifying the destination/source
of a communication. There are three types of address information elements:

Global title.

Subsystem number.

Signalling point code (together with the MTP-SAP instance).

The global title is an address such as dialled digits which does not explicitly contain information that
would allow routing in the signalling network, i.e. a translation function is required. The subsystem
number is an identification of a specific user function within a certain signalling point (SP), like the
ISDN-user part, the SCCP-management, etc.
The parameter "responding address" identifies the SCCP user to which the connection has been
established or refused.
The "responding address" parameter in the N-CONNECT primitive conveys the address of the SCCP
service access point to which the signalling connection has been established. Under certain
circumstances (e.g. a general global title identifying replicated subsystems), the value of this
parameter may be different from the "called address" in the corresponding N-CONNECT request.
The "responding address" parameter is present in the N-DISCONNECT primitive only in the case
where the primitive is used to indicate rejection of a signalling connection establishment attempt by
an SCCP user function. The parameter conveys the address of the service access point from which
the N-DISCONNECT-request was issued and under circumstances like that mentioned above the
"responding address" may be different from the "called address" in the corresponding N-CONNECT
request primitive.

12

Recommendation Q.711

(07/96)

The parameter "expedited data selection" may be used to indicate during setup whether expedited
data can be transferred via the connection. A negotiation will be performed between SCCP users,
local and remote.
The quality of service parameter set is used during call setup to negotiate the protocol class for the
connection and, if applicable, the flow control window size.
The N-CONNECT primitives may or may not contain user data.
The parameter "connection identification" is used to allocate a primitive to a certain connection. The
connection identification is an internal representation of the "connection endpoint identifier" defined
in the OSI-RM. Its use and format is implementation dependent.
The "importance parameter" is a user optional parameter in request and response primitives that
result in the transmission of SCCP messages. Its use allows the SCCP user to assign and indicate to
SCCP a certain importance to the primitive. During MTP and/or SCCP congestion, SCCP will take
decisions to send out or reject the resulting message, based on this importance and on the severity of
the congestion. Its presence in the indication and confirmation primitive is an SCCP implementation
option.
In principle, the connection establishment has to be completed (i.e. data transfer status has to be
reached) before sending or receiving data messages. If data messages arrive at the calling user before
the connection establishment is finished, these data messages are discarded.
In addition, user data can also be transferred to and from the SCCP within the primitives
N-CONNECT and N-DISCONNECT.
6.1.1.2.3

Data transfer phase

During this phase three different primitives may occur:

a)
b)
c)

N-DATA (Table 3);

N-EXPEDITED DATA (Table 4);
N-RESET (Table 5).

The primitive "N-DATA" (Table 3) exists only as a "request", i.e. from the SCCP user to the local
SCCP and as an "indication" at the remote end of the connection, i.e. from the SCCP to the local
SCCP user. N-DATA can occur bidirectionally, i.e. from the calling as well as the called user of the
SCCP-connection.
The primitive "N-EXPEDITED DATA" may only be used by the SCCP user in case of protocol
class 3 connections.
Table 3/Q.711 Parameters of the primitive N-DATA
Primitive
Parameter

N-DATA
request

N-DATA
indication

User data

M(=)

User data

Connection identification

Importance

Recommendation Q.711

(07/96)

13

Table 4/Q.711 Parameters of the primitive N-EXPEDITED DATA

Primitive
Parameter

N-EXPEDITED
DATA request

N-EXPEDITED
DATA indication

User data

M(=)

Connection identification

The primitive N-RESET (Table 5) can occur in the data transfer state of a connection with a protocol
class including flow control. N-RESET overrides all other activities and causes the SCCP to start a
re-initialization procedure for sequence numbering. N-RESET appears as a request, an indication, a
response and a confirm. After reception of an N-RESET request and before the sending of an
N-RESET confirm, all NSDUs from the remote SCCP and the local SCCP user are discarded by the
local SCCP.
Table 5/Q.711 Parameters of the primitive N-RESET
Primitive
Parameter

N-RESET
request

N-RESET
indication

N-RESET
response

N-RESET
confirm

(Always NSU)

n.a.

n.a.

Reason

n.a.

n.a.

Connection identification

Originator

The parameter "originator" indicates the source of the reset and can be any of the following: the
"network service provider" (network originated), the "network service user" (user originated), or
"undefined". The parameter "reason" indicates "network service provider congestion", "reason
unspecified" or "local SCCP originated1" for a network originated reset, and indicates "user
synchronization" for a user originated reset. The "reason" parameter is "undefined" when the
"originator" parameter is "undefined".
6.1.1.2.4

Release phase

The primitives for the release phase are N-DISCONNECT request and N-DISCONNECT indication.
These primitives are also used for the connection refusal during connection establishment phase.
Parameters are included to notify the reason for connection release/refusal and the initiator of the
connection release/refusal procedure. User data may be also be included (see Table 6).
The parameter "originator" indicates the initiator of the connection release or the connection refusal.
It may assume the following values:

the network service provider;

the network service user;

undefined.

____________________
1

14

These values may be used locally at the originating/initiating node as an implementation option.
Recommendation Q.711

(07/96)

Table 6/Q.711 Parameters of the primitive N-DISCONNECT

Primitive
Parameter

Originator

N-DISCONNECT
request

N-DISCONNECT
indication

(Always NSU)

Responding address

Cc2)a)

Reason

User data

C(=)c2)

Connection identification

Importance

a)

Only applicable in the case of connection refusal.

c2)

If present in the received SCCP message.

a)

The parameter "reason" gives information about the cause of the connection release or the connection
refusal. It may assume any of the following values in accordance with the value of the "originator":
1)

2)

When the "originator" parameter indicates the "network service provider":

disconnection abnormal condition of non-transient nature;
disconnection abnormal condition of transient nature;
disconnection invalid state1;

disconnection release in progress1;

connection refusal2 destination address unknown (non-transient condition);
connection refusal2 destination inaccessible/non-transient condition;
connection refusal2 destination inaccessible/transient condition;

connection refusal2 QOS not available/non-transient condition;

connection refusal2 QOS not available/transient condition;
connection refusal2 reason unspecified/non-transient condition;
connection refusal2 reason unspecified/transient condition;

connection refusal2 local error1;

connection refusal2 invalid state1;
connection refusal2 no translation1;
connection refusal2 in restart phase1;

connection refusal2 hop counter violation.

When the "originator" parameter indicates the "network service user":
disconnection normal condition;
disconnection abnormal condition;

disconnection end user congestion;

disconnection end user failure;

____________________
2

It is noted that the term "connection rejection" is used in Recommendation X.213 for the "reason"
parameter values.
Recommendation Q.711

(07/96)

15

3)

disconnection SCCP user originated;

disconnection access congestion;

disconnection access failure;

disconnection subsystem congestion;
connection refusal2 non-transient condition;
connection refusal2 transient condition;

connection refusal2 incompatible information in NSDUs;

connection refusal2 end user originated;
connection refusal2 end user congestion;
connection refusal2 end user failure;

connection refusal2 SCCP user originated;

connection refusal2 access congestion;
connection refusal2 access failure;
connection refusal2 subsystem congestion.

When the "originator" parameter is "undefined", then the "reason" parameter is also
"undefined".

6.1.1.3

Additional SCCP primitive and interface elements

In addition to those primitives in Recommendation X.213, there is a primitive N-INFORM that could
be used by the SCCP connection-oriented services during data transfer phase. There are also three
interface elements used by user part type A, e.g. ISDN-UP, as in Figure 1.
6.1.1.3.1

Notice service

The provision of the notice service by use of the "N-INFORM" primitive is implementation
dependent.
The primitive N-INFORM (Table 7) is used during data transfer to convey relevant network/user
information. The primitive "N-INFORM" will contain the parameters "reason", "connection
identification" and "QOS parameter set".
The primitive "N-INFORM request" is provided to inform the local SCCP of the connection user
failure/congestion, or anticipated QOS changes. A further primitive "N-INFORM indication" is
provided to indicate actual failures of the local SCCP to the SCCP-user functions or anticipated
quality of service changes or other indications to the SCCP-user functions.
The parameter "reason" contains the network/user information to be conveyed. It may assume the
following values:

network service provider failure;

network service congestion;

network service provider QOS change;

network service user failure;
network service user congestion;
network service user QOS change;

reason unspecified.

16

Recommendation Q.711

(07/96)

Table 7/Q.711 Parameters of the primitive N-INFORM

Primitive
Parameter

N-INFORM
request

N-INFORM
indication

Reason

Connection identification

QOS parameter set

c3)

6.1.1.3.2

c3)

c3)

Present in inform reasons that lead to a QOS parameter set change.

Connection establishment interface elements

For the user part type A in Figure 1, two mechanisms are available to set up a signalling connection.
For example, the ISDN-user part may use the mechanism described in 6.1.1.2.2 or may request the
SCCP to initiate a connection and return the information to the ISDN-user part for transmission
within an ISDN-user part call setup message, like an Initial Address Message (IAM).
Three interface elements are defined for the information flow between SCCP and ISDN-user part:
a)
REQUEST to the SCCP, type 1 and type 2;
b)

REPLY from the SCCP.

The REQUEST type 1 contains the following parameters:

connection identification (O);

expedited data selection (U);

quality of service parameter set (U).

The REQUEST type 2 contains the following parameters:

quality of service parameter set (M);

connection identification (O);

source local reference (M);
originating signalling point code (M);
reply request (U);

refusal indicator (U).

The REPLY contains the following parameters:

source local reference (M);

quality of service parameter set (M);

connection identification (O).

6.1.2

Permanent signalling connections

6.1.2.1

Description

The setup/release service is controlled by the administration (e.g. OMAP). The functions for setup
and release may be similar to those provided for temporary signalling connections. The classes of
service are the same.
Permanently established signalling connections may require additional safeguarding mechanisms
within the endpoints (relaypoints) of the connection in order to guarantee their re-establishment in
case of a malfunction followed by a recovery.

Recommendation Q.711

(07/96)

17

6.1.2.2

Primitives and parameters

The primitives and their parameters are listed in Table 8. Their content and functionality correspond
to the description within 6.1.1.2.3.
Table 8/Q.711 Primitives for the data transfer on permanent connections
Primitives
Generic name

6.2

Specific name

Parameters

N-DATA

Request
Indication

Importance
User data
Connection identification

N-EXPEDITED DATA

Request
Indication

User data
Connection identification

N-RESET

Request
Indication
Response
Confirm

Originator
Reason
Connection identification

Connectionless services

The SCCP provides the SCCP user with the ability to transfer signalling messages via the signalling
network without setup of a signalling connection. In addition to the MTP capability, a "routing"
function has to be provided within the SCCP, which maps the called address to the signalling point
codes of the MTP service.
This mapping function is provided within each node, or is distributed over the network or is provided
in some special translation centres.
The SCCP also includes the ability to segment/reassemble user data that cannot be transferred in one
MTP message. More details can be found in 4.1.1/Q.714.
Under certain conditions of congestion and unavailability of subsystems and/or signalling points,
connectionless messages in support of SCCP-SDUs could be discarded instead of being transferred.
If the SCCP user wishes to be informed of the non-delivery of a SCCP-SDU caused by the discard of
a message, the return option parameter must be set to "return SCCP-SDU on error" in the primitive to
the SCCP.
6.2.1

Description

The connectionless SCCP offers two services:

Class 0:
The basic connectionless class without guaranteed in-sequence delivery of SCCP-SDUs.
The SCCP user can invoke this service by means of the parameter "sequence control" in
the N-UNITDATA.request primitive being absent; and
Class 1:

The in-sequence delivery connectionless class with guaranteed3 in-sequence delivery of

SCCP-SDUs. The SCCP user can invoke this service by means of the parameter
"sequence control" in the N-UNITDATA.request primitive being present.

____________________
3

18

By the MTP network or by concatenated MTP networks concerned (for further information see
Recommendation Q.706).
Recommendation Q.711

(07/96)

NOTE These two services are provided by SCCP making use of the sequence control mechanisms provided
by the MTP in a distinct way:
a)

The class 0 service allows the SCCP to insert SLS values randomly, or with the aim to achieve an
appropriate load sharing within the underlying MTP network.

b)

The class 1 service requires the SCCP to insert the same SLS for all the SCCP-SDUs associated with
given parameters "sequence control" and "called address".

The rules to achieve load sharing in the MTP network are not defined in the SCCP
Recommendations.
6.2.2

Primitives and parameters of the connectionless service

6.2.2.1

Overview

Table 9 gives an overview of the primitives to the upper layers and the corresponding parameters for
the connectionless service.
Table 9/Q.711 Primitives and parameters of the connectionless service
Primitives
Generic name

Specific name

Parameters

N-UNITDATA

Request
Indication

Called address
Calling address
Sequence control
Return option
Importance
User data

N-NOTICE

Indication

Called address
Calling address
Reason for return
User data
Importance

6.2.2.2
6.2.2.2.1

Parameters
Address

The parameters "called address" and "calling address" serve to identify the destination and
origination respectively, of the SCCP-SDU to be conveyed in connectionless messages. It should be
noted that the called and calling addresses may be different at the origination and destination. These
parameters may contain some combination of global title, subsystem number and signalling point
code.
The global title is an address such as dialled digits which does not explicitly contain information that
would allow routing in the signalling network, i.e. a translation function is required. The subsystem
number is an identification of a specific user function within a certain signalling node, like the ISDNuser part, the SCCP-management, etc.

Recommendation Q.711

(07/96)

19

6.2.2.2.2

Sequence control

The presence of the parameter "sequence control" indicates to the SCCP that the user requires to
invoke the "sequence guaranteed" service. In the case of "sequence guaranteed" service, this
parameter is an indication to the SCCP that a given stream of SCCP-SDUs has to be delivered in
sequence. The value of this parameter together with the called address is also used to distinguish
different streams of messages so that the SCCP can allocate SLS codes appropriately to help the
MTP in achieving an even distribution of signalling traffic. If the SCCP user does not provide a
sequence control parameter, then the SCCP assumes protocol class 0.
6.2.2.2.3

Return option

The parameter "return option" is used to determine the handling of SCCP-SDUs encountering
transport problems.
"Return option" may assume the following values:

discard SCCP-SDU on error;

return SCCP-SDU on error.

If the SCCP user does not provide a return option parameter, then the SCCP assumes messages will
be discarded on error, causing loss of SCCP-SDUs.
6.2.2.2.4

Reason for return

The parameter "reason for return" identifies the reason why a SCCP-SDU was not able to be
delivered to its final destination.
"Reason for return" may assume the following values:

no translation for an address of such nature;

no translation for this specific address;

subsystem congestion;
subsystem failure;
unequipped user;
MTP failure;

network congestion;
SCCP unqualified;
error in message transport;
error in local processing;

destination cannot perform reassembly;

SCCP failure;
hop counter violation;
segmentation not supported;

segmentation failed.

6.2.2.2.5

User data

The parameter "user data" is information which is to be transferred transparently between SCCP
users. In the case of the N-NOTICE primitive, the "user data" parameter may be incomplete.

20

Recommendation Q.711

(07/96)

6.2.2.2.6

Importance

The "importance parameter" is a user optional parameter in request primitives that result in the
transmission of SCCP messages. Its use allows the SCCP user to assign and indicate to SCCP a
certain importance to the primitive. During MTP and/or SCCP congestion, SCCP will take decisions
to send out or reject the resulting message, based on this importance and on the severity of the
congestion. Its presence in the indication primitives is an SCCP implementation option.
6.2.2.3
6.2.2.3.1

Primitives
UNITDATA

The "N-UNITDATA request" primitive is the means by which an SCCP user requests the SCCP to
transfer SCCP-SDUs to a peer SCCP user.
The "N-UNITDATA indication" primitive informs a user that a SCCP-SDU is being delivered to it
from the peer SCCP user.
Table 10 indicates the parameters of the primitive N-UNITDATA.
6.2.2.3.2

NOTICE

The "N-NOTICE indication" primitive is the means by which the SCCP returns to the originating
user a SCCP-SDU which could not reach the final destination.
Table 11 indicates the parameters of the primitive N-NOTICE.
Table 10/Q.711 Parameters of the primitive N-UNITDATA
Primitive
Parameter

N-UNITDATA
request

N-UNITDATA
indication

Called address

Calling address

a)

Sequence control

Return option

User data

M(=)

Importance

a)

This parameter is associated with the SCCP service access point at

which the primitive is issued if the calling address is absent.

Recommendation Q.711

(07/96)

21

Table 11/Q.711 Parameters of the primitive N-NOTICE

Primitive
Parameter

6.2.3

N-NOTICE
indication

Called address

Calling address

Reason for return

User data

Importance

State transition diagram

The network-connectionless transmission service primitive can be used to transmit a self-contained

SCCP-SDU from one SCCP-SAP to another SCCP-SAP in a single service access; thus no initial
establishment or subsequent release of a network-connection is required. This SCCP-SDU can be
independent (class 0) or appear in a sequence where sequence integrity is preserved (class 1).
The state transition diagram, as seen by the SCCP user using the services provided by the
connectionless SCCP is shown in Figure 9.

N-UNITDATA.request/indication
N-NOTICE.indication

Idle
T1178330-96

Figure 9/Q.711 State transition diagram for sequence

of connectionless service primitives at one SCCP-SAP

6.3

SCCP management

6.3.1

Description

The SCCP provides SCCP management procedures (see clause 5/Q.714) to maintain network
performances by rerouting or throttling traffic in the event of failure or congestion in the network.
These SCCP management procedures apply to both the connection-oriented and the connectionless
services of the SCCP.
6.3.2
6.3.2.1

Primitives and parameters of the SCCP management

Overview

Table 12 gives an overview of the primitives to the upper layers and the corresponding parameters
for the SCCP management.

22

Recommendation Q.711

(07/96)

Table 12/Q.711 Primitives and parameters of the SCCP management

Primitives
Generic name

Specific name

Parameters

N-COORD

Request
Indication
Response
Confirm

Affected subsystem
Subsystem multiplicity indicator

N-STATE

Request
Indication

Affected subsystem
User status
Subsystem multiplicity indicator

N-PCSTATE

Indication

Affected signalling point (together

with the MTP-SAP instance)
Signalling point status
Restricted importance level
Remote SCCP status

6.3.2.2

Parameters

6.3.2.2.1

Affected subsystem

The parameter "affected subsystem" identifies a user which is failed, withdrawn, or allowed. The
"affected subsystem" parameter contains the same type of information as the "called address" and
"calling address", except the global title portion.
6.3.2.2.2

User status

The parameter "user status" is used to inform a SCCP user of the status of the affected subsystem.
"User status" may assume one of the following values:

User-in-service (UIS);

User-out-of-service (UOS).
6.3.2.2.3

Subsystem multiplicity indicator

The parameter "subsystem multiplicity indicator" identifies the number of replications of a

subsystem. This parameter is reserved for national application.
6.3.2.2.4

Affected signalling point

The parameter "affected signalling point" identifies a signalling point or SCCP which is failed,
congested, or allowed. The "affected signalling point" parameter contains unique identification of a
signalling point.
6.3.2.2.5

Signalling point status

The parameter "signalling point status" is used to inform a user of the status of an affected signalling
point.
"Signalling point status" may assume the following values:

signalling point inaccessible;

signalling point congested;

signalling point accessible.

Recommendation Q.711

(07/96)

23

6.3.2.2.6

Remote SCCP status

The parameter "remote SCCP status" is used to inform a user of the status of a remote SCCP.
"Remote SCCP status" may assume the following values:

remote SCCP available;

remote SCCP unavailable, reason unknown;

remote SCCP unequipped;

remote SCCP inaccessible;

remote SCCP congested.

6.3.2.2.7

Restricted importance level

The parameter "restricted importance level" is used to inform an SCCP user of the importance level
at which traffic is being restricted by SCCP towards a remote signalling point or SCCP. When the
user is able to identify the remote signalling point or SCCP, it may decide not to send any primitives
of importance numerically below the level indicated that will result in messages towards the (SCCP
at that) remote signalling point. Primitives of importance numerically equal to or greater than the
level indicated will still be sent (to ensure equitable treatment with users not in a position to identify
the remote signalling point or SCCP).
6.3.2.3
6.3.2.3.1

Primitives
COORD

The "N-COORD" primitive (Table 13) is used by replicated subsystems to coordinate the withdrawal
of one of the subsystems.
The primitive exists as: a "request" when the originating user is requesting permission to go
out-of-service; an "indication" when the request to go out-of-service is delivered to the originator's
replicate; a "response" when the originator's replicate announced it has sufficient resources to let the
originator go out-of-service; and as a "confirm" when the originator is informed that it may go
out-of-service.
Table 13/Q.711 Parameters of the primitive N-COORD
Primitive
Parameter

N-COORD
request

N-COORD
indication

N-COORD
response

N-COORD
confirm

Affected subsystem

Subsystem multiplicity indicator

n.a.

n.a.

6.3.2.3.2

STATE

The "N-STATE request" primitive (Table 14) is used to inform the SCCP management about the
status of the originating user. The "N-STATE indication" primitive is used to inform an SCCP user
accordingly.

24

Recommendation Q.711

(07/96)

Table 14/Q.711 Parameters of the primitive N-STATE

Primitive
Parameter

6.3.2.3.3

N-STATE
request

N-STATE
indication

Affected subsystem

User status

Subsystem multiplicity indicator

n.a.

PCSTATE

The "N-PCSTATE primitive" (Table 15) is used to inform a user about the status of a signalling
point or a remote SCCP.
Table 15/Q.711 Parameters of the primitive N-PCSTATE
Primitive
Parameter

N-PCSTATE
indication

Affected signalling point

Signalling point status

Remote SCCP status

c5)

Restricted importance level

c6)

c5)

Present if this is the result of an MTP-STATUS reporting user part unavailability or

the reception of an SSC message reporting a change of restricted importance level, or
a time-out (Tcon) to detect the abatement of SCCP congestion.

c6)

Present if this is the result of a change in the restricted importance level of the
affected signalling point or remote SCCP.

Definition of the lower boundary of the SCCP

7.1

MTP-SAP

The services provided by the MTP are offered at two different MTP-SAPs:
a)
b)

An MTP-SAP that supports a maximum MTP-SDU size of 272 octets, including the MTP
routing label (see 2.3.8/Q.703).
An MTP-SAP that supports a maximum MTP-SDU size of 4095 octets, including the MTP
routing label (see 9.1/Q.2210).

With the exception of the maximum supported SDU size, these two SAPs offer equivalent services.
7.2

MTP-primitives and parameters

The primitives supported by the MTP are specified in Table 1/Q.701 (MTP-3), and Table 1/Q.2210
(MTP-3b), respectively. Table 16 specifies how the MTP-primitives apply when SCCP is using the
services of the MTP. In the case of conflicting statements between this Recommendation and
Recommendations Q.701 or Q.2210, Recommendations Q.701 and Q.2210 take precedence.

Recommendation Q.711

(07/96)

25

Table 16/Q.711 Message transfer part service primitives

Primitives
Generic name
MTP-TRANSFER

Parameters

Specific name
Request
Indication

OPC (2.2/Q.704)
DPC (2.2/Q.704)
SLS (2.2/Q.704)a)
SIO (14.2/Q.704)
User datac)

MTP-PAUSE (stop)

Indication

Affected DPC

MTP-RESUME (start)

Indication

Affected DPC

MTP-STATUS

Indication

Affected DPC
b)

Cause
a)

The SCCP should assist load sharing within the underlying MTP network by making use of
an appropriate choice of SLS values (distributed as equally as possible). Where in-sequence
delivery is required, the same SLS value should be used.

b)

The cause parameter has, at present, four values:

i) Signalling network congested (plus optional level).
The level value is included if national options with congestion priorities or multiple
signalling link states without congestion priorities as in Recommendation Q.704 are
implemented.
ii) User part unavailability: unknown (user part identity is SCCP).
iii) User part unavailability: unequipped remote user (user part identity is SCCP).
iv) User part unavailability: inaccessible remote user (user part identity is SCCP).
If the cause was "unknown", "inaccessible remote user" or "signalling network
congestion" without "level", it is the responsibility of the SCCP to determine when the
remote SCCP is again available.

c)

7.2.1

If the selected MTP-SAP instance is an MTP as described in Recommendations Q.701 to

Q.707, the "user data" parameter is defined in 2.3.8/Q.703. If the selected MTP-SAP
instance is an MTP as described in Recommendation Q.2210 ("MTP-3b"), the parameter
"user data" is as defined in 9.1/Q.2210.

TRANSFER

The primitive "MTP-TRANSFER" is used between SCCP and MTP to provide the MTP message
transfer service.
7.2.2

PAUSE

The primitive "MTP-PAUSE" indicates to the SCCP the total inability of providing the MTP service
to the specified destination4.
NOTE The signalling point is inaccessible via the MTP. The MTP will determine when the signalling point
is again accessible and send MTP-RESUME indication. The user should wait for such an indication and,
meanwhile, is not allowed to send messages to that signalling point. If the remote peer user is thought to be
unavailable, that condition may be maintained or cancelled at the local user's discretion.

____________________
4

26

If MTP provides services according to Recommendation Q.704, see 7.2.6/Q.701, items iii), iv) and v);
otherwise, this reference to Recommendation Q.701 does not apply.
Recommendation Q.711

(07/96)

7.2.3

RESUME

The primitive "MTP-RESUME" indicates to the SCCP the ability of providing the MTP service to
the specified destination4.
This primitive corresponds to the destination accessible state as defined in Recommendation Q.704.
NOTE When the "MTP-RESUME" indication is given to each user, the MTP does not know whether the
remote peer user is available. This is the responsibility of each user.

7.2.4

STATUS

The primitive "MTP-STATUS" indicates to the SCCP the partial inability of providing the MTP
service to the specified destination. The primitive is also used to indicate to a user that a remote
corresponding user is unavailable and the cause for unavailability (see 11.2.7/Q.704).
In the case of national option with congestion priorities and multiple signalling link congestion states
without priorities, as in Recommendation Q.704, are implemented, this "MTP-STATUS" primitive is
also used to indicate a change of congestion level.
This primitive corresponds to the destination congested/user part unavailable state as defined in
Recommendation Q.704.
NOTE In the case of remote user unavailability, the user is responsible for determining the availability of
this peer user. The user is cautioned not to send normal traffic to the peer user because, while such peer user is
unavailable, no message will be delivered but each will result in a repeated MTP-STATUS indication. The
MTP will not send any further indications about the unavailability or availability of this peer user unless the
local user continues to send messages to the peer user.

7.2.5

Notification of completion of MTP restart procedure

When the MTP restart procedure is terminated, the MTP indicates the end of MTP restart to all local
MTP users showing each signalling point's accessibility or inaccessibility. The means of doing this is
implementation dependent (see clause 9/Q.704).
It might be modelled by the MTP-RESUME.indications at the appropriate MTP-SAP instance.
7.3

State transition diagram

The state transition diagrams, as seen by the SCCP using the services provided by the MTP, are
shown in Figures 10, 11 and 12.
Each state transition diagram applies to a single signalling relation, therefore, there exist as many
state transition diagrams as there are signalling relations. Figure 10 is an abstract model of the
interface between the MTP and the SCCP. It is not reflected in the management procedures and the
SDL diagrams in Recommendation Q.714.

Recommendation Q.711

(07/96)

27

MTP signalling relation

unavailable
3

Failure

MTP-RESUME.indication
(Note 2)
MTP-RESUME.indication

MTP-PAUSE.indication

MTP-PAUSE.indication
(Note 2)

Failure

MTP signalling relation

not initialized
1

MTP signalling relation

available
2

MTP-TRANSFER.request
MTP-TRANSFER.indication
MTP-STATUS.indication (for
a remote unavailable SCCP
or to indicate MTP congestion)
(Note 3)
T1178340-96

MTP-TRANSFER.indication (Note 1)
MTP-STATUS.indication (for a remote unavailable SCCP or to indicate MTP congestion)

NOTE 1 MTP-TRANSFER.indication in state 3 is a result of the availability of the signalling relation towards the local
MTP, but the unavailability of the signalling relation towards the remote MTP.
NOTE 2 These transitions are implicity triggered by the MTP restart procedure.
NOTE 3 The MTP itself does not keep track of the status of the remote MTP users, so the SCCP is responsible for
detecting the availability of its remote peer SCCP.

Figure 10/Q.711 State transition diagram for sequence of MTP-primitives

across the upper boundary of the MTP-3 for one MTP signalling relation
that is managed by the SCCP - MTP international
method of congestion reporting

28

Recommendation Q.711

(07/96)

MTP-RESUME.indication

MTP-PAUSE.indication

MTP signalling relation

unavailable
3

Failure

MTP-RESUME.indication
(Note 2)

MTP-PAUSE.indication
(Note 2)

Failure

Failure

MTP signalling relation

not initialized
1

MTP signalling relation

available
2

MTP-STATUS.indication,
level = 0
MTP-STATUS.indication,
level 0

MTP-TRANSFER.request
MTP-TRANSFER.indication
MTP-STATUS.indication
(unavailable remote SCCP) (Note 3)
MTP-PAUSE.indication

MTP signalling relation

congested
4

T1178350-96

MTP-TRANSFER.indication (Note 1)
MTP-STATUS.indication (for
unavailabe remote SCCP or MTP
congestion level 0)

MTP-TRANSFER.request
MTP-TRANSFER.indication
MTP-STATUS.indication (for
unavailable remote SCCP or
MTP congestion level 0)
(Note 4)

NOTE 1 MTP-TRANSFER.indication in state 3 is a result of the availability of the signalling relation towards the local MTP,
but the unavailability of the signalling relation towards the remote MTP.
NOTE 2 These transitions are implicitly triggered by the MTP restart procedure.
NOTE 3 The MTP itself does not kepp track of the status of the remote MTP users, then, the SCCP is responsible for
detecting the availability of its remote peer SCCP.
NOTE 4 Further study is required to take into account the MTP level congestion procedure into the SCCP congestion
procedures.

Figure 11/Q.711 State transition diagram for sequence of MTP-primitives

across the upper boundary of the MTP-3 for one MTP signalling relation
that is managed by the SCCP - MTP multiple congestion
levels with congestion priorities

Recommendation Q.711

(07/96)

29

MTP signalling relation

unavailable
3

Failure

MTP-RESUME.indication
(Note 2)
MTP-RESUME.indication

MTP-PAUSE.indication

MTP-PAUSE.indication
(Note 2)

Failure

MTP signalling relation

not initialized
1

MTP signalling relation

available
2
T1178360-96

MTP-TRANSFER.request
MTP-TRANSFER.indication
MTP-STATUS.indication (for
a remote unavailable SCCP or to
indicate MTP congestion + level)
(Note 3)

MTP-TRANSFER.indication (Note 1)
MTP-STATUS.indication (for
a remote unavailable SCCP or to
indicate MTP congestion + level)
NOTE 1 - MTP-TRANSFER.indication in state 3 is a result of the availability of the signalling relation towards the local
MTP, but the unavailability of the signalling relation towards the remote MTP.
NOTE 2 - These transitions are implicitly triggered by the MTP restart procedure.
NOTE 3 - The MTP itself does not keep track of the status of the remote MTP users, so the SCCP is responsible for
detecting the availability of its remote peer SCCP.

Figure 12/Q.711 State transition diagram for sequence of MTP-primitives

across the upper boundary of the MTP-3 for one MTP signalling
relation that is managed by the SCCP - MTP multiple
congestion levels without priorities

30

Recommendation Q.711

(07/96)

Functions provided by the SCCP

This clause is an overview of the functional blocks within the SCCP.

8.1

Connection-oriented functions

8.1.1

Functions for temporary signalling connections

8.1.1.1

Connection establishment functions

The connection establishment service primitives defined in 6.1 are used to set up a signalling
connection.
The main functions of the connection establishment phase are listed below:

set up of a signalling connection;

establish the optimum size of NPDUs (network protocol data unit);

map network address onto signalling relations;
select functions operational during data transfer phase (for instance, layer service selection);
provide means to distinguish network connections;

transport user data (within the request).

8.1.1.2

Data transfer phase function

The data transfer phase functions provide means for a two-way simultaneous transport of messages
between the two endpoints of the signalling connection.
The main functions of the data transfer phase as listed below are used or not used in accordance with
the result of the selection performed in the connection establishment phase:

segmenting/reassembling;

flow control;

connection identification;
NSDU delimiting (Mbit);
expedited data;
missequence detection;

reset;
others.

8.1.1.3

Release phase functions

These functions provide disconnection of the signalling connection, regardless of the current phase
of the connection. The release may be performed by an upper layer stimulus or by maintenance of the
SCCP itself. The release can start at each end of the connection (symmetrical procedure).
The main function of the release phase is the disconnection.
8.1.2
8.1.2.1

Functions for permanent signalling connections

Connection establishment phase and connection release phase functions

The stimuli for set-up and release of permanent connections are originated from the administration
function.

Recommendation Q.711

(07/96)

31

8.1.2.2

Data transfer phase functions

The functions for the data transfer on permanent signalling connections correspond to that for
temporary connections. Differences may exist regarding the quality of service.
8.2

Connectionless service functions

The functions of the connectionless service are listed below:

mapping the network address to signalling relations;

sequence service;
segmenting.

8.3

Management functions

The SCCP provides functions which manage the status of the SCCP subsystems. These functions
allow other nodes in the network to be informed of the change in status of SCCP subsystems at a
node, and to modify SCCP translation data if appropriate.
SCCP management also keeps track of the congestion status of MTP destinations and remote SCCPs.
For subsystems running in dominant mode or loadshared mode, a possibility is foreseen to negotiate
taking one replicated subsystem out of service with the other subsystem remaining in service. This
allows to check whether the other side is capable (i.e. has enough resources, real time) to receive the
extra traffic load. The replicated subsystem initiating the procedure is taken out of service only after
the other subsystem has answered positively to the request.
When a subsystem is out of service, SCCP test functions are activated at nodes receiving
unavailability information. At periodic intervals the status of the unavailable subsystem is checked
by a SCCP management procedure.
Broadcast functions within SCCP management broadcast subsystem status changes to nodes within
the network which have an immediate need to be informed of a particular signalling point/subsystem
status change.
Notification functions to local subsystems within the node (local broadcast) are also provided.
The capability of a remote SCCP node to test the availability of a subsystem at a restarting SCCP
node before resuming traffic to that node or subsystem is for further study. The capability of a
remote SCCP node to test the availability of the SCCP when the signalling point becomes accessible,
before resuming traffic to/via that node, is for further study. In addition, the application of these tests
and the protocol specification are for further study. See 5.2.3/Q.714 and 5.3.4.2/Q.714.
8.4

Routing and translation functions

The SCCP routing provides a powerful address translation function, which is asked for
connectionless and connection-oriented service. The SCCP routing provides a powerful addressing
information translation function on behalf of its users. This function makes it unnecessary for SCCP
users to store knowledge of SCCP signalling routing information. The routing function also responds
to the MTP and SCCP congestion reports. Detailed description of the SCCP routing function can be
found in 2.3/Q.714 and 2.4/Q.714.

32

Recommendation Q.711

(07/96)

ITU-T RECOMMENDATIONS SERIES

Series A

Organization of the work of the ITU-T

Series B

Means of expression

Series C

General telecommunication statistics

Series D

General tariff principles

Series E

Telephone network and ISDN

Series F

Non-telephone telecommunication services

Series G

Transmission systems and media

Series H

Transmission of non-telephone signals

Series I

Integrated services digital network

Series J

Transmission of sound-programme and television signals

Series K

Protection against interference

Series L

Construction, installation and protection of cables and other elements of outside plant

Series M

Maintenance: international transmission systems, telephone circuits, telegraphy,

facsimile and leased circuits

Series N

Maintenance: international sound-programme and television transmission circuits

Series O

Specifications of measuring equipment

Series P

Telephone transmission quality

Series Q

Switching and signalling

Series R

Telegraph transmission

Series S

Telegraph services terminal equipment

Series T

Terminal equipments and protocols for telematic services

Series U

Telegraph switching

Series V

Data communication over the telephone network

Series X

Data networks and open system communication

Series Z

Programming languages