Heat Transfer & Thermodynamics in Nuclear Reactors

Heat Transfer & Thermodynamics in
Nuclear Reactors
Dr. Ugur GUVEN
Heat Transfer Principles

The most important mechanism in Nuclear
Reactors is the concept of heat transfer.
The amount of heat that is transferred
determines the amount of work that the
nuclear reactor is able to achieve.
Standard rules of thermodynamics and heat
transfer apply to nuclear reactors
You want the nuclear reactor to produce as
much heat as possible for higher efficiency
Laws of Thermodynamics
The first law, also known as Law of
Conservation of Energy, states that
energy can not be created or
destroyed; it can only be
redistributed or changed from one
form to another.
The second law of thermodynamics
says that the entropy of any isolated
system not in
thermal equilibrium almost always
increases.
The third law of thermodynamics
states that the entropy of a system
approaches a constant value as
the temperature approaches zero.
Thermodynamic Work and Heat
Isothermal and Adiabatic Process

An isothermal process is a change of a system, in
which the temperature remains constant: T = 0.
This typically occurs when a system is in contact
with an outside thermal reservoir (heat bath), and
the change occurs slowly enough to allow the
system to continually adjust to the temperature of
the reservoir through heat exchange.
In contrast, an adiabatic process is where a system
exchanges no heat with its surroundings (Q = 0). In
other words, in an isothermal process, the value
T = 0 but Q 0, while in an adiabatic process, T
0 but Q = 0.
Thermodynamic Principles
Nuclear Reactors work with the same
objective of creating work through heat
The amount of heat that is harnessed can be
transformed to work through various
thermodynamic processes.
The percentage of conversion from heat to
work determined the thermodynamic
efficiency of the reactor
Standard Steam Cycle
Carnot Cycle
If a nuclear power plant is to be taken as an ideal

machine, then the best way to ideally create work
out of heat would be the Carnot Cycle.
Carnot Cycle is an ideal heat engine
It is a well known fact that for the best thermal
efficiency of a heat engine, it is essential to
increase the temperatures of the heat input,
while decreasing the temperature of the rejected
heat.
Hence, the equation for the efficiency of the
Carnot cycle is shown by:
Efficiency Sample Problem

If the heat generator produces heat at 300
degrees Celsius and if the cooling water for
the condenser comes from a source with 20
degrees Celsius, then the efficiency would be
Carnot Cycle
This is why commercial nuclear power plants (or any thermal
power plant for that matter) are placed near environmental
lakes and large water sources, so that the waste heat can be
dissipated without a large increase in the environmental
temperature TL. Obviously, TL will be higher in summer times
or in hot geographical locations causing the efficiency of the
heat cycle to be lowered.
But, for the majority parts of the world, TL will be changing
within a reasonable frame of 20o C to 35o C. to Thus, for all
intents and purposes you cant change the efficiency of the
nuclear reactor with TL and so the only variable that you can
really play with is the TH or the high temperature of the heat
reservoir. Hence, increasing the heat will always increase the
efficiency of an ideal Carnot cycle for which most power
plants are modeled after.
Thermodynamic Cycle Efficiency

(Ideal)
Pressurized Water Reactor
Heat Transfer Mechanisms

The main heat transfer mechanisms are:
1) Conduction
2) Convection
3) Thermal Radiation
Heat Transfer
Conduction or diffusion: The transfer of energy
between objects that are in physical contact.
Convection: The transfer of energy between an
object and its environment, due to fluid motion.
Radiation: The transfer of energy to or from a body
by means of the emission or absorption of
electromagnetic radiation.
Advection: The transfer of energy from one
location to another as a side effect of physically
moving an object containing that energy. (like
putting a bottle of iced water in a room)
Heat Transfer in the Fuel Rod
Heat Transfer in Nuclear Reactors

As the nuclear reaction takes place, the fuel
rods transfer heat to each other and to the
rest of the reactor core that they are in
contact with by conduction.
As the coolant takes the heat from the fuel
rods, the heat is transferred to the coolant by
convection.
Some of the heat is transferred by radiation as
electromagnetic energy is heated away from
the fission reaction to the coolant as well as to
the solid body of the reactor core.
Heat Transfer in Fuel Rod

Let the rate of supply of thermal energy by fission
to be uniform throughout the rod. If the rod is long
in comparison with its radius R, then most of the
heat flow is in the radial direction.
If the surface is maintained by temperature Ts by
the flow of the coolant, then the temperature at the
center of the rod To must be higher.
q1
R2q
To Ts
4k
4k
Problem 1
Heat Transfer in Fuel Rods
Calculate the temperature difference for a reactor
fuel rod with radius of 0.5 cm at a point where the
power density is q=200 W/cm^3. Take conductivity
of U02 as k=0.062 W/cm.C
q1
R2q
To Ts
4k
4k
To-Ts = ((0.5)^2)(200) / (4 * 0.062)

Hence we get:
To-Ts = 201.61 Celsius
Reactor Thermal Power

As coolant flows along the many channels
surrounding fuel pins in a reactor, it absorbs
thermal energy and rises in temperature.
If coolant of specific heat c enters the reactor
at temperature Tc(in) and leaves at Tc(out)
then the reactor thermal power is:
Where M is coolant flow in kg/s
P cM (Tcout Tcin )
Problem 2
If the mass flow rate of a nuclear reactor with
3000 MW power is 19,800 kg/sec and if water
enters at 300 degrees Celsius calculate the
temperature at which the water leaves. Take
specific heat of 6.06 x 10^3 J/kg-C
P cM (Tcout Tcin )
With the equation above:
19,800 = (3000 x 10^6)/((6.66 x 10^3)(300-T))
T(out) = 325 C
Coolant Mass Flow for PWR

If we calculate the condenser coolant mass flow
for a reactor with Rate M, we can use the
following formula where P is power:
Coolant flow will be received in terms of kg/sec.

You can turn this to volume flow rate by dividing
into specific gravity multiplied by 1000. You will
get the rate in meter cube per second.
Problem 3
Convert the volume flow rate in the previous
problem to liters per minute. Take specific
gravity of 0.687
V=(19800 kg/s)/(687 kg/m^3) = 28.8 m^3/s
Since 1 min = 60 sec
V= 28.8 x 60 = 1728 m^3 / min
1 m^3 = 1000 liters
V= 1,728,000 liters per minute
Waste Power
A nuclear plant operating at electrical power
1000 MWe with an efficiency of 33% would
have a thermal power of
1000 / 0.33 = 3030 MWt
Thus, it must reject a waste power of
P= 2030 MWt
This waste power is lost as internal energy and
as waste heat. It is transferred to coolant and
then to coolant towers for discharge into
atmosphere and / or to the body of water.
Cooling Towers
Waste heat is extracted to the atmosphere by
cooling towers in nuclear reactors. Usually,
water vapor is given out.
Cooling Tower Structure
Heat in Reactor Shutdown

Even when the reactor is shut down, there will
be some heat that is being generated by the
fuel rods. The amount of heat that is
generated even after shutdown will occur for
some time.
It is essential to keep the coolant circulating
even after the reaction has been stopped in
order to protect the reactor containment from
having a steam explosion or from having a
meltdown.

Heat Transfer & Thermodynamics in Nuclear Reactors

Uploaded by

Copyright:

Available Formats

Heat Transfer & Thermodynamics in Nuclear Reactors

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Heat Transfer & Thermodynamics in Nuclear Reactors

Uploaded by

Copyright:

Available Formats

Heat Transfer & Thermodynamics in

Heat Transfer Principles

Thermodynamic Work and Heat

Isothermal and Adiabatic Process

Standard Steam Cycle

If a nuclear power plant is to be taken as an ideal

Efficiency Sample Problem

Thermodynamic Cycle Efficiency

Pressurized Water Reactor

Heat Transfer Mechanisms

Heat Transfer in the Fuel Rod

Heat Transfer in Nuclear Reactors

Heat Transfer in Fuel Rod

To-Ts = ((0.5)^2)(200) / (4 * 0.062)

Reactor Thermal Power

Coolant Mass Flow for PWR

Coolant flow will be received in terms of kg/sec.

Cooling Tower Structure

Heat in Reactor Shutdown

You might also like