ANSI ISA TR12.13.01 R2005 - Flammability Characteristics of Combustible Gases and Vapors

TECHNICAL REPORT
ANSI/ISATR12.13.011999 (R2005)
A Technical Report prepared by ISA and registered with ANSI
Flammability Characteristics of
Combustible Gases and Vapors
Reaffirmed 31 August 2005

TM
ISAThe Instrumentation,
Systems, and
Automation Society
Copyright The Instrumentation, Systems, and Automation Society
Provided by IHS under license with ISA
No reproduction or networking permitted without license from IHS
--`,,```,,,,````-`-`,,`,,`,`,,`---
Not for Resale
ANSI/ISATR12.13.011999 (R2005)
Flammability Characteristics of Combustible Gases and Vapors
ISBN: 1-55617-697-X
Copyright 2005 by ISA. All rights reserved. Printed in the United States of America. No part of this
publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any
means (electronic, mechanical, photocopying, recording, or otherwise), without the prior written
permission of the Publisher.
ISA
67 Alexander Drive
P.O. Box 12277
Research Triangle Park, North Carolina 27709
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
PREFACE
This preface, as well as all footnotes and annexes, is included for information purposes and is not part of
ANSI/ISA-TR12.13.01-1999 (R2005).
This Standard has been prepared as part of the service of ISA toward a goal of uniformity in the field
of instrumentation. To be of real value, this document should not be static but should be subject
to periodic review. Toward this end, the Society welcomes all comments and criticisms and asks
that they be addressed to the Secretary, Standards and Practices Board; ISA; 67 Alexander Drive;
P. O. Box 12277; Research Triangle Park, NC 27709; Telephone (919) 549-8411; Fax (919) 549-8288;
E-mail: [email protected].
The ISA Standards and Practices Department is aware of the growing need for attention to the metric
system of units in general, and the International System of Units (SI) in particular, in the preparation of
instrumentation standards. The Department is further aware of the benefits to USA users of ISA standards
of incorporating suitable references to the SI (and the metric system) in their business and professional
dealings with other countries. Toward this end, this Department will endeavor to introduce SI-acceptable
metric units in all new and revised standards, recommended practices, and technical reports to the
greatest extent possible. Standard for Use of the International System of Units (SI): The Modern Metric
System, published by the American Society for Testing & Materials as IEEE/ASTM SI 10-97, and future
revisions, will be the reference guide for definitions, symbols, abbreviations, and conversion factors.
It is the policy of ISA to encourage and welcome the participation of all concerned individuals and interests
in the development of ISA standards, recommended practices, and technical reports. Participation in the
ISA standards-making process by an individual in no way constitutes endorsement by the employer of that
individual, of ISA, or of any of the standards, recommended practices, and technical reports that ISA
develops.
CAUTIONISA ADHERES TO THE POLICY OF THE AMERICAN NATIONAL STANDARDS
INSTITUTE WITH REGARD TO PATENTS. IF ISA IS INFORMED OF AN EXISTING PATENT THAT IS
REQUIRED FOR USE OF THE STANDARD, IT WILL REQUIRE THE OWNER OF THE PATENT TO
EITHER GRANT A ROYALTY-FREE LICENSE FOR USE OF THE PATENT BY USERS COMPLYING
WITH THE STANDARD OR A LICENSE ON REASONABLE TERMS AND CONDITIONS THAT ARE
FREE FROM UNFAIR DISCRIMINATION.
EVEN IF ISA IS UNAWARE OF ANY PATENT COVERING THIS STANDARD, THE USER IS
CAUTIONED THAT IMPLEMENTATION OF THE STANDARD MAY REQUIRE USE OF TECHNIQUES,
PROCESSES, OR MATERIALS COVERED BY PATENT RIGHTS. ISA TAKES NO POSITION ON THE
EXISTENCE OR VALIDITY OF ANY PATENT RIGHTS THAT MAY BE INVOLVED IN IMPLEMENTING
THE STANDARD. ISA IS NOT RESPONSIBLE FOR IDENTIFYING ALL PATENTS THAT MAY
REQUIRE A LICENSE BEFORE IMPLEMENTATION OF THE STANDARD OR FOR INVESTIGATING
THE VALIDITY OR SCOPE OF ANY PATENTS BROUGHT TO ITS ATTENTION. THE USER SHOULD
CAREFULLY INVESTIGATE RELEVANT PATENTS BEFORE USING THE STANDARD FOR THE
USERS INTENDED APPLICATION.
HOWEVER, ISA ASKS THAT ANYONE REVIEWING THIS STANDARD WHO IS AWARE OF ANY
PATENTS THAT MAY IMPACT IMPLEMENTATION OF THE STANDARD NOTIFY THE ISA
STANDARDS AND PRACTICES DEPARTMENT OF THE PATENT AND ITS OWNER.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
ADDITIONALLY, THE USE OF THIS STANDARD MAY INVOLVE HAZARDOUS MATERIALS,

OPERATIONS OR EQUIPMENT. THE STANDARD CANNOT ANTICIPATE ALL POSSIBLE
APPLICATIONS OR ADDRESS ALL POSSIBLE SAFETY ISSUES ASSOCIATED WITH USE IN
HAZARDOUS CONDITIONS. THE USER OF THIS STANDARD MUST EXERCISE SOUND
PROFESSIONAL JUDGMENT CONCERNING ITS USE AND APPLICABILITY UNDER THE USERS
PARTICULAR CIRCUMSTANCES. THE USER MUST ALSO CONSIDER THE APPLICABILITY OF
ANY GOVERNMENTAL REGULATORY LIMITATIONS AND ESTABLISHED SAFETY AND HEALTH
PRACTICES BEFORE IMPLEMENTING THIS STANDARD.
The following people served as members of ISA Subcommittee SP12.13 and approved ANSI/ISA-TR12.13.01-1999:
--`,,```,,,,````-`-`,,`,,`,`,,`---
NAME
COMPANY
M. Coppler, Chairman*
D. Bishop, Managing Director
W. Alexander
D. Ankele*
B. Apel
R. Bierzynski
E. Briesch*
C. Brown
S. Bruce
J. Cawley
J. Chilton
D. Chou
C. Coache*
S. Czaniecki
L. Greenwalt
C. Groppetti*
A. Guerrera
L. Hamman
K. Hedrick
C. Hendrickson
B. Holcom
K. Johnson
P. Kelly*
R. Landman
D. Li
R. Lyle
J. McCann
R. Menot*
J. Miller*
R. Merritt
R. Novack*
K. Patel
R. Poling
D. Pongrance
M. Schaeffer
W. Shao
Ametek Inc.
Chevron Petroleum Technology Company
Mine Safety Appliances Company
Underwriters Laboratories Inc.
MSA Instrument
Scott Health & Safety
Enmet Corporation
Delphian Corporation
U.S. Dept of the Interior
U.S. Bureau of Mines
International Sensor Tech.
Factory Mutual Research Corporation
Intrinsic Safety Concepts Inc.
Marathon Oil Co.
Detector Electronics Corp.
Sola Communications Inc.
U.S. Coast Guard
U.S. Dept. of Labor
Northern Illinois Gas Co.
Gas Tech. Inc.
KWJ Engineering Inc.
Underwriters Laboratories, Inc.
Intl. Marine Products Inc.
Canadian Standards Assoc.
Motorola Inc.
International Sensor Technologies
Factory Mutual Research Corp.
Detector Electronics Corp.
Edu-tech Industries
Ametek Inc.
Scott Aviation
EI du Pont
General Monitors
Control Instruments Corporation
Canadian Standards Association
______
* One vote per company.

Not for Resale
D. Styrcula
J. Thomason
D. Wagner
R. Wanek
D. Wechsler
R. Wek
D. Wolsk
ANSI/ISA-TR12.13.01-1999 (R2005)

OMNI Industrial Systems, Inc.
Industrial Scientific Corp.
Bacharach Inc.
Union Carbide Corporation
General Monitors
Wolsk Alarms, Ltd.
The following people served as members of ISA Committee SP12 and approved ANSI/ISA-TR12.13.01-1999:
NAME
COMPANY
F. McGowan, Chairman*
D. Bishop, Managing Director*
N. Abbatiello*
D. Ankele*
B. Apel
A. Ballard*
G. Bentinck
K. Boegli
R. Brodin
M. Buettner
R. Buschart
R. Cardinal
C. Casso
M. Coppler
J. Cospolich
J. Costello
S. Czaniecki
T. Dubaniewicz
U. Dugar
A. Engler
T. Feindel
W. Fiske
G. Garcha
E. Geissler
E. Henning
D. Hohenstein
D. Jagger*
J. Kuczka
B. Larson
W. Lawrence*
E. Magison
R. Masek
K. McManama*
I. McMurchie
R. McNeal*
A. Mobley*
S. Nguyen
Factory Mutual Research Corporation

Eastman Kodak Company
MSA Instrument
Crouse-Hinds Company
E. I. du Pont
Phoenix Contact Inc.
Fisher Controls International, Inc.
Ralston Purina Company
PC & E, Inc.
Bently Nevada Corporation
Schlumberger Oil Field Services
Ametek Inc.
Waldemar S. Nelson & Company, Inc.
Henkel Corp.
NIOSH
Mobil Chemical Company
EGS Electrical Group
R. Stahl, Inc.
Intertek Testing Services
PCS Engineering
Bartec US Corp.
Bailey-Fischer & Porter
Pepperl+Fuchs Inc.
Hawke America
Killark
Turck Inc.
Honeywell, Inc.
Bailey Controls Company
Petromarine of Texas
Hawke America
3M Company
Milltronics Ltd.
______
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
E. Olson*
A. Page III
J. Propst
T. Schnaare
W. Shao
J. Thomason
D. Wechsler
3M Company
MSHA Certification Center
Shell Oil Products Co.
Rosemount, Inc.
Canadian Standards Assoc.
OMNI Industrial Systems, Inc.
Union Carbide Corporation
The following members of the ISA Standards and Practices Board approved ANSI/ISA-TR12.13.01-1999
for publication on 28 February 1999.
NAME
COMPANY
H. Dammeyer
H. Baumann
D. Bishop
P. Brett
M. Cohen
M. Coppler
W. Holland
A. Iverson
R. Jones
V. Maggioli
T. McAvinew
A. McCauley, Jr.
R. McFarland
R. Reimer
J. Rennie
R. Webb
W. Weidman
J. Weiss
J. Whetstone
M. Widmeyer
R. Wiegle
C. Williams
G. Wood
M. Zielinski
The Ohio State University

H. D. Baumann, Inc.
Honeywell, Inc.
Senior Flexonics, Inc.
Ametek, Inc.
Southern Company
Ivy Optiks
Dow Chemical Co.
Feltronics Corp.
Instrumentation & Control Engineering LLC
Chagrin Valley Controls, Inc.
Honeywell, Inc.
Rockwell Automation
Altran Corp.
Parsons Energy & Chemicals Group
EPRI
National Institute of Standards & Technology
Consultant
CANUS Corp.
Eastman Kodak Co.
Graeme Wood Consulting
Fisher-Rosemount Systems, Inc.
______
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13-01-1999 (R2005)
The following people served as members of ISA Subcommittee SP12.13 and reaffirmed
ANSI/ISA-TR12.13.01-1999 (R2005):
NAME
COMPANY
J. Miller, Chairman
M. Coppler, Managing Director
J. Berthold
R. Bolotin
C. Brown
S. Bruce
P. Byrne
S. Czaniecki
G. Garcha
K. Hedrick
B. Holcom
D. Mills
L. Owen
M. Phadke
R. Poling
M. Schaeffer
P. Schimmoeller
R. Seitz
A. Skinner
K. Thompson
D. Wechsler
C. Yong
Detector Electronics Corporation

Ametek Inc.
Senscient Ltd.
General Monitors Inc.
Enmet Corporation
Delphian Corporation
FM Approvals
GE Energy
MSHA Approval & Certification Center
RKI Instruments
Dooley Tackaberry Inc.
Bayer India Ltd.
E I du Pont
Control Instruments Corporation
CSA International
Artech Engineering
Crowcon Gas Detection
MSA Company
Dow Chemical Company
Shell Exploration & Production Company
NAME
COMPANY
T. Schnaare, Chairman
W. Lawrence, Co-Chairman
M. Coppler, Managing Director
N. Abbatiello
D. Ankele
A. Ballard
D. Bishop
H. Bockle
K. Boegli
D. Burns
R. Buschart
R. Cardinal
C. Casso
J. Cospolich
S. Czaniecki
J. Dolphin
T. Dubaniewicz
U. Dugar
A. Engler
W. Fiske
G. Garcha
D. Hohenstein
D. Jagger
Rosemount, Inc.
FM Approvals
Ametek Inc.
Optimation Technology
Crouse Hinds Division of Cooper Industries
David N Bishop Consultant
R. Stahl Inc.
Phoenix Contact Inc.
Shell Exploration & Production Company
Cable Tray Institute
Bently Nevada LLC
Nabors Industries
Waldemar S Nelson & Company Inc.
Professional Testing
NIOSH
Mobil Chemical Company
EGS/ECM
Intertek Testing Services
GE Energy
Pepperl + Fuchs Inc.
Bifold-Fluid Power

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
The following people served as members of ISA Committee SP12 and reaffirmed
ANSI/ISA-TR12.13.01-1999 (R2005):
ANSI/ISA-TR12.13-01-1999 (R2005)
J. Jonscher
F. Kent
P. Kovscek
J. Kuczka
B. Larson
E. Massey
A. Mobley
A. Page
P. Schimmoeller
R. Seitz
D. Wechsler
Adalet PLM
Honeywell Inc.
Industrial Scientific Corporation
Killark
Turck Inc.
Rockwell Automation
3M Company
MSHA Approval & Certification Center
CSA International
Artech Engineering
Dow Chemical Company
ANSI/ISA-TR12.13.01-1999 (R2005) was reaffirmed by the following ISA Standards and Practices Board
on 26 August 2005.
COMPANY
I. Verhappen, Chair
F. Amir
D. Bishop
M. Coppler
B. Dumortier
W. Holland
E. Icayan
A. Iverson
R. Jones
V. Maggioli
T. McAvinew
A. McCauley
G. McFarland
R. Reimer
J. Rennie
N. Sands
H. Sasajima
T. Schnaare
A. Summers
R. Webb
W. Weidman
J. Weiss
M. Widmeyer
C. Williams
M. Zielinski
Syncrude Canada Ltd.

E I Du Pont Company
David N Bishop, Consultant
Ametek, Inc.
Schneider Electric
Consultant
ACES Inc
Ivy Optiks
Consultant
Feltronics Corporation
Jacobs Engineering Group
Chagrin Valley Controls, Inc.
Emerson Process Management Power & Water Sol.
Rockwell Automation
Consultant
E I du Pont
Yamatake Corporation
Rosemount Inc.
SIS-TECH Solutions LLC
Consultant
Worley Parsons
KEMA Inc.
Stanford Linear Accelerator Center
Eastman Kodak Company
Emerson Process Management
--`,,```,,,,````-`-`,,`,,`,`,,`---
NAME

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
CONTENTS
FOREWORD .........................................................................................................................................11
ABSTRACT ...........................................................................................................................................11
KEY WORDS.........................................................................................................................................11
--`,,```,,,,````-`-`,,`,,`,`,,`---
APPENDIX I ........................................................................................................................................ 13

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---

This page intentionally left blank.
Not for Resale
11
ANSI/ISA-TR12.13.01-1999 (R2005)
FOREWORD
Publication of this Technical Report that has been registered with ANSI has been approved by the
Accredited Standards Developer ISA, 67 Alexander Drive, Research Triangle Park, NC 27709. This
document is registered as a Technical Report according to the Procedures for the Registration of
Technical Reports with ANSI. This document is not an American National Standard and the material
contained herein is not normative in nature. Comments on the content of this document should be sent to
the Secretary, Standards and Practices Board; ISA; 67 Alexander Drive; P. O. Box 12277; Research
Triangle Park, NC 27709.
As a service to industry, the accompanying document, Bureau of Mines Bulletin 627 - Flammability
Characteristics of Combustible Gases and Vapors, by Zabetakis 1965, is hereby reprinted in its entirety.
This compendium, formerly available from the U.S. Bureau of Mines, contains information essential to an
understanding of detection, measurement and handling of flammable gases and vapors.
For further information, refer to ANSI/ISATR12.13.02.
The reader should be aware that more recent LFL/UFL figures are available in NFPA 497, and
IEC 60079-20.
ABSTRACT
This technical report includes theoretical and practical work carried out and collected by the U.S. Bureau
of Mines relating to ignition and explosive properties of flammable gas mixtures. Flammability limits, under
varying conditions of proportion, temperature and pressure, are presented.
While the primary emphasis is on methane-air mixtures as found in coal mines, a full treatment of many
other gases and vapors is included.
KEY WORDS
--`,,```,,,,````-`-`,,`,,`,`,,`---
Methane
Fire
Explosion
Flammability limits
Flammable
Combustible
LEL, UEL
LFL, UFL
Gas

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
13
ANSI/ISA-TR12.13.01-1999 (R2005)
APPENDIX I
The following document, Flammability Characteristics of Combustible Gases and Vapors, is
reprinted in its entirety by permission of the publisher, the Bureau of Mines, U.S. Department of the
Interior.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
14
Bulletin 627
Bureau of Mines
FLAMMABILITY CHARACTERISTICS OF COMBUSTIBLE

GASES AND VAPORS,
U.S. Bureau of Mines, Bulletin 627
By Michael G. Zabetakis

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
AD 701 576
15
ANSI/ISA-TR12.13.01-1999 (R2005)
This publication has been cataloged as follows:
Zabetakis, Michael George, 1924-2005

Flammability characteristics of combustible gases and vapors. [Washington] U.S. Dept. of the
Interior, Bureau of Mines [1965]
121 p. illus., tables. (U.S. Bureau of Mines. Bulletin 627)
Includes bibliography.
1. Combustion gases. 2. Gases. 3. Vapors. I. Title. II. Title: Combustible gases. (Series)
TN23.U4 no. 627 622.06173
--`,,```,,,,````-`-`,,`,,`,`,,`---
U.S. Dept. of the Int. Library

A.1

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
16
FLAMMABILITY CHARACTERISTICS OF COMBUSTIBLE

GASES AND VAPORS
by
Michael G. Zabetakis"
Abstract
This is a summary of the available limit of flammability, autoignition, and burning-rate data for
more than 200 combustible gases and vapors in air and other oxidants, as well as of empirical
rules and graphs that can be used to predict similar data for thousands of other combustibles
under a variety of environmental conditions. Specific data are presented on the paraffinic,
unsaturated, aromatic, and alicyclic hydrocarbons, alcohols, ethers, aldehydes, ketones, and
sulfur compounds, and an assortment of fuels, fuel blends, hydraulic fluids, engine oils, and
miscellaneous combustible gases and vapors.
Introduction
Prevention of unwanted fires and gas explosion disasters requires a knowledge of flammability
characteristics (limits of flammability, ignition requirements, and burning rates) of pertinent
combustible gases and vapors likely to be encountered under various conditions of use (or
misuse). Available data may not always be adequate for use in a particular application since they
may have been obtained at a lower temperature and pressure than is encountered in practice.
For example, the quantity of air that is required to decrease the combustible vapor concentration
to a safe level in a particular process carried out at 200C should be based on flammability data
obtained at this temperature. When these are not available, suitable approximations can be
made to permit a realistic evaluation of the hazards associated with the process being
considered; such approximations can serve as the basis for designing suitable safety devices for
the protection of personnel and equipment.
The purpose of this bulletin is to present a general review of the subject of flammability, and to
supply select experimental data and empirical rules on the flammability characteristics of various
families of combustible gases and vapors in air and other oxidizing atmospheres. It contains
what are believed to be the latest and most reliable data for more than 200 combustibles of
interest to those concerned with the prevention of disastrous gas explosions. In addition, the
empirical rules and graphs presented here can be used to predict similar data for other
combustibles under a variety of conditions. This bulletin supplements Bureau bulletins (40)N and
other publications (158).
"
Physical chemist, project coordinator, Gas Explosion, Explosives Research Center, Bureau of Mines,
Pittsburgh, Pa.
Work on manuscript completed May 1964.
N
Italicized numbers in parentheses refer to items in the bibliography at the end of this report.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
17
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Basic knowledge of combustion is desirable for a thorough understanding of the material, which
can be found in numerous publications (69, 199, 202). Therefore, only those aspects required for
an understanding of flammability are considered here; even these are considered from a fairly
elementary viewpoint.
Definitions and Theory

LIMITS OF FLAMMABILITY
A combustible gas-air mixture can be burned over a wide range of concentrationswhen either
subjected to elevated temperatures or exposed to a catalytic surface at ordinary temperatures.
However, homogeneous combustible gas-air mixtures are flammable, that is, they can propagate
flame freely within a limited range of compositions. For example, trace amounts of methane in
air can be readily oxidized on a heated surface, but a flame will propagate from an ignition source
at ambient temperatures and pressures only if the surrounding mixture contains at least 5 but
less than 15 volume-percent methane. The more dilute mixture is known as the lower limit, or
combustible-lean limit, mixture; the more concentrated mixture is known as the upper limit, or
combustible-rich limit, mixture. In practice, the limits of flammability of a particular system of
gases are affected by the temperature, pressure, direction of flame propagation, gravitational
field strength, and surroundings. The limits are obtained experimentally by determining the
limiting mixture compositions between flammable and non-flammable mixtures (244). That is,
L T, P = 1/2 [ C gn + C 1f ],
(1)
U T, P = 1/2 [ C gf + C 1n ],
(2)
and
where LT,P and UT,P are the lower and upper limits of flammability, respectively, at a specified
temperature and pressure, Cgn and C1n are the greatest and least concentrations of fuel in
oxidant that are nonflammable, and C1f and Cgf are the least and greatest concentrations of fuel
in oxidant that are flammable. The rate at which a flame propagates through a flammable
mixture depends on a number of factors including temperature, pressure, and mixture
composition. It is a minimum at the limits of flammability and a maximum at near stoichiometric
mixtures (130).
The Bureau of Mines has adopted a standard apparatus for limit-of-flammability determinations
(40). Originally designed for use at atmospheric pressure and room temperature, it was later
modified for use at reduced pressures by incorporating a spark-gap ignitor in the base of the 2inch, glass, flame-propagation tube. This modification introduced a difficulty that was not
immediately apparent, as the spark energy was not always adequate for use in limit-offlammability determinations. Figure 1 illustrates the effect of mixture composition on the
electrical spark energy requirements for ignition of methane-air mixtures (75). For example, a
0.2-millijoule (mj) spark is inadequate to ignite even a stoichiometric mixture at atmospheric
pressure and 26C; a 1-mj spark can ignite mixtures containing between 6 and 11.5 volumepercent methane, etc. Such limit-mixture compositions that depend on the ignition source
strength may be defined as limits of ignitibility or more simply ignitibility limits; they are thus

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
18
--`,,```,,,,````-`-`,,`,,`,`,,`---
indicative of the igniting ability of the energy source. Limit mixtures that are essentially
independent of the ignition source strength and that give a measure of the ability of a flame to
propagate away from the ignition source may be defined as limits of flammability. Considerably
greater spark energies are required to establish limits of flammability than are required for limits
of ignitibility (218); further, more energy is usually required to establish the upper limit than is
required to establish the lower limit. In general, when the source strength is adequate, mixtures
just outside the range of flammable compositions yield flame caps when ignited. These flame
caps propagate only a short distance from the ignition source in a uniform mixture. The reason
for this may be seen in figure 2 which shows the effect of temperature on limits of flammability at
a constant initial pressure. As the temperature is increased, the lower limit decreases and the
upper limit increases. Thus, since a localized energy source elevates the temperature of nearby
gases, even a nonflammable mixture can propagate flame a short distance from the source.
That is, a nonflammable mixture (for example, composition-temperature point A, fig. 2) may
become flammable for a time, if its temperature is elevated sufficiently (composition-temperature
point B).
Figure 1Ignitibility Curve and Limits of Flammability for Methane-Air Mixtures at

Atmospheric Pressure and 26C.
Flammable mixtures considered in figure 2 fall in one of three regions. The first is left of the
saturated vapor-air mixtures curve, in the region labeled "Mist". Such mixtures consist of
droplets suspended in a vapor-air mixture; they are discussed in greater detail in the section on
formation of flammable mixtures. The second lies along the curve for saturated vapor-air

Not for Resale
19
ANSI/ISA-TR12.13.01-1999 (R2005)
mixtures; the last and most common region lies to the right of this curve. Compositions in the
second and third regions make up the saturated and unsaturated flammable mixtures of a
combustible-oxidant system at a specified pressure.
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 2Effect of Temperature on Limits of Flammability of a Combustible Vapor

in Air at a Constant Initial Pressure.
In practice, complications may arise when flame propagation and flammability limit
determinations are made in small tubes. Since heat is transferred to the tube walls from the
flame front by radiation, conduction, and convection, a flame may be quenched by the
surrounding walls. Accordingly, limit determinations must be made in apparatus of such a size
that wall quenching is minimized. A 2-inch-ID vertical tube is suitable for use with the paraffin
hydrocarbons (methane, ethane, etc.) at atmospheric pressure and room temperature. However,
such a tube is neither satisfactory under these conditions for many halogenated and other
compounds nor for paraffin hydrocarbons at very low temperatures and pressures (197, 244).
Because of the many difficulties associated with choosing suitable apparatus, it is not surprising
to find that the very existence of the limits of flammability has been questioned. After a thorough
study, Linnett and Simpson concluded that while fundamental limits may exist there is no
experimental evidence to indicate that such limits have been measured (132). In a more recent
publication, Mullins reached the same conclusion (154). Accordingly, the limits of flammability
obtained in an apparatus of suitable size and with a satisfactory ignition source should not be
termed fundamental or absolute limits until the existence of such limits has been established.
However, as long as experimentally determined limits are obtained under conditions similar to

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
20
Industrially, heterogeneous single-phase (gas) and multi-phase (gas, liquid, and solid) flammable
mixtures are probably even more important than homogeneous gas mixtures. Unfortunately, our
knowledge of such mixtures is rather limited. It is important to recognize, however, that
heterogeneous mixtures can ignite at concentrations that would normally be nonflammable if the
mixture were homogeneous. For example, 1 liter of methane can form a flammable mixture with
air near the top of a 100-liter container, although a nonflammable (1.0 volume-percent) mixture
would result if complete mixing occurred at room temperature. This is an important concept,
since layering can occur with any combustible gas or vapor in both stationary and flowing
mixtures. Roberts, Pursall, and Sellers (176-180) have presented an excellent series of review
articles on the layering and dispersion of methane in coal mines.
The subject of flammable sprays, mists, and foams is well-documented (5, 18, 22, 27, 76, 205,
215, 245). Again, where such heterogeneous mixtures exist, flame propagation can occur at socalled average concentrations well below the lower limit of flammability (86); thus, the term
"average" may be meaningless when used to define mixture composition in heterogeneous
systems.
IGNITION
Lewis and von Elbe (130), Mullins (153,154), and Belles and Swett (156) have prepared
excellent reviews of the processes associated with spark-ignition and spontaneous-ignition of a
flammable mixture. In general, many flammable mixtures can be ignited by sparks having a
relatively small energy content (1 to 100 mj) but a large power density (greater than 1 megawatt/
cm3). However, when the source energy is diffuse, as in a sheet discharge, even the total energy
requirements for ignition may be extremely large (79, 82, 85, 123, 181, 228). There is still much
to be learned in this field, however, since electrical discharges are not normally as well defined in
practice as they are in the laboratory.
When a flammable mixture is heated to an elevated temperature, a reaction is initiated that may
proceed with sufficient rapidity to ignite the mixture. The time that elapses between the instant
the mixture temperature is raised and that in which a flame appears is loosely called the time lag
or time delay before ignition. In general, this time delay decreases as the temperature increases.
According to Semenov (193), these quantities are related by the expression
0.22E
log t = -------------- + B,
T
(3)
where t is the time delay before ignition in seconds; E is an apparent activation energy for the
rate controlling reaction in calories per mole; T is the absolute temperature, expressed in
degrees, Kelvin; and B is a constant. Two types of ignition temperature data are found in the
current literature. In the first, the effect of temperature on time delay is considered for delays of
less than 1 second (127, 153). Such data are applicable to systems in which the contact time
between the heated surface and a flowing flammable mixture is very short; they are not
satisfactory when the contact time is indefinite. Further, equation (3) is of little help, because it
gives only the time delay for a range of temperatures at which autoignition occurs; if the
temperature is reduced sufficiently, ignition does not occur. From the standpoint of safety, it is
the lowest temperature at which ignition can occur that is of interest. This is called the minimum

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
those found in practice, they may be used to design installations that are safe and to assess
potential gas-explosion hazards.
21
ANSI/ISA-TR12.13.01-1999 (R2005)
spontaneous-ignition, or autoignition, temperature (AIT) and is determined in a uniformly heated

apparatus that is sufficiently large to minimize wall quenching effects (194, 237). Figures 3 and 4
illustrate typical autoignition-temperature data. In figure 3 the minimum autoignition-temperature
or AIT value for n-propyl nitrate is 170 C at an initial pressure of 1,000 psig (243). Data in this
1- plot such as that in figure 4. Such graphs
figure may be used to construct a log t versus -T
illustrate the applicability of equation (3) to autoignition temperature data. The equation of the
broken line in figure 4 is
3
12.3 10
log t = ------------------------- 25.1 .
T
(4)
In this specific case, equation (4) is applicable only in the temperature range from 170 to 195C;
another equation must be used for data at higher temperatures. The solid lines in figure 4 define
an 8C band that includes the experimental points in the temperature range from 170 to 195C.
FORMATION OF FLAMMABLE MIXTURES
In practice, flammable mixtures may form either by accident or design. When they are formed by
accident, it is usually desirable to reduce the combustible concentration quickly by adding
enough air or inert gas to produce nonflammable mixtures. Under certain conditions, it may be
possible to increase the combustible concentration so as to produce a nonflammable mixture.
Such procedures are discussed in greater detail in the following section.
Flammable mixtures are encountered in production of many chemicals and in certain physical
operations. These include gasfreeing a tank containing a combustible gas (232), drying plasticwire coating, and recovering solvent from a solvent-air mixture. When layering can occur, as in
drying operations, it is not enough to add air at such a rate that the overall mixture composition is
below the lower limit of flammability (assuming that uniform mixtures result). Special precautions
must be taken to assure the rapid formation of nonflammable mixtures (235). When a batch
process is involved, an added precaution must be taken; a constituent at a partial pressure near
its vapor pressure value may condense when it is momentarily compressed by addition of other
gases or vapors. Accordingly, mixtures that are initially above the upper limit of flammability may
become flammable. A similar effect, must be considered when mixtures are sampled with
equipment that is cooler than the original sample; if vapor condenses in the sampling line, the

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
In practice, heterogeneous mixtures are always formed when two gases or vapors are first
brought together. Before discussing the formation of such mixtures in detail, a simplified mixer
such as that shown in figure 5 will be considered briefly. This mixer consists of chambers 1 and
2 containing gases A and B, respectively; chamber 2, which contains a stirrer, is separated from
chamber 1 and piston 3 by a partition with a small hole, H. At time to, a force F applied to piston 3
drives gas A into chamber 2 at a constant rate. If gas A is distributed instantaneously throughout
chamber 2 as soon as it passes through H, a composition diagram such as that given in figure 6
results; the (uniform) piston motion starts at to, and stops at tF. However, if a time interval Dt is
required to distribute a small volume from chamber 1 throughout chamber 2, then at any instant
between to, and tF + Dt, a variety of mixture compositions exists in chamber 2. This situation is
represented schematically in figure 7. The interval of time during which heterogeneous gas
mixtures would exist in the second case is determined in part by the rate at which gas A is added
to chamber 2, by the size of the two chambers, and by the efficiency of the stirrer.
ANSI/ISA-TR12.13.01-1999 (R2005)
22
test sample will not yield accurate data. A flammable mixture sampled in this manner may
appear to be nonflammable and thus create a hazardous situation (236).
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
23
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 3Time Delay Before Ignition of NPN in Air at 1,000 Psig in the
Temperature Range From 150 to 210C. (1-33 apparatus; type-347,
stainless steel test chamber.)
TEMPERATURE, C
Figure 4Logarithm of Time Delay Before Ignition of NPN in Air at 1,000 Psig
Initial Pressure. (Data from figure 3.)
A flammable mixture can also form at temperatures below the flash point of the liquid
combustible either if the latter is sprayed into the air, or if a mist or foam forms. With fine mists
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
24
and sprays (particle sizes below 10 microns), the combustible concentration at the lower limit is
about the same as that in uniform vapor-air mixtures (17, 18, 22, 24, 76, 245). However, as the
droplet diameter increases, the lower limit appears to decrease. In studying this problem,
Burgoyne found that coarse droplets tend to fall towards the flame front in an upward propagating
flame, and as a result the concentration at the flame front actually approaches the value found in
lower limit mixtures of fine droplets and vapors (24). With sprays, the motion of the droplets also
affects the limit composition, so that the resultant behavior is rather complex. The effect of mist
and spray droplet size on the apparent lower limit is illustrated in figure 8. Kerosine vapor and
mist data were obtained by Zabetakis and Rosen (245); tetralin mist data, by Burgoyne and
Cohen (24); kerosine spray data, by Anson (5); and the methylene bistearamide data, by
Browning, Tyler, and Krall (18).
Flammable mist-vapor-air mixtures may occur as the foam on a flammable liquid collapses.
Thus, when ignited, many foams can propagate flame. Bartkowiak, Lambiris, and Zabetakis
found that the pressure rise DP produced in an enclosure by the complete combustion of a layer
of foam of thickness hf is proportional to hf and inversely proportional to ha, the height of the air
space above the liquid before foaming (7). That is
hf
DP ----ha
(5)
Pressures in excess of 30 psi were produced by the ignition of foams in small containers.
Thomas found that an additional hazard could arise from production of foams by oxygenenriched air at reduced pressures (215). Air can become oxygen-enriched as the pressure is
reduced, because oxygen is more soluble than nitrogen in most liquids (83). Thus the presence
of foams on combustible liquids are a potential explosion hazard.
A flammable foam can also form on nonflammable liquid if the foam is generated by a flammable
gas mixture instead of air. Burgoyne and Steel, who studied this problem, found that the
flammability of methane-air mixtures in water-base foams was affected by both the wetness of
the foam and the bubble size (28).
Chamber 1
--`,,```,,,,````-`-`,,`,,`,`,,`---
Chamber 2
Gas A
Figure 5Simplified mixer

Not for Resale
Gas B
25
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 6Composition of Gas in Chamber 2, Figure 5 (Instantaneous Mixing).
Figure 7Composition of Gas in Chamber 2, Figure 5 (Delayed Mixing).
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
26
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 8Variation in Lower Limits of Flammability of Various Combustibles in Air

as a Function of Droplet Diameter.

Not for Resale
27
ANSI/ISA-TR12.13.01-1999 (R2005)
Presentation of Data
Limit-of-flammability data that have been obtained at a specified temperature and pressure with a
particular combustible-oxidant-inert system may be presented on either a triangular or a
rectangular plot. For example, figure 9 shows a triangular flammability diagram for the system
methane-oxygen-nitrogen. This method of presentation is frequently used because all mixture
components are included in the diagram. However, as the sum of all mixture compositions at any
point on the triangular plot is constant (100 pct) the diagram can be simplified by use of a
rectangular plot (244). For example, the flammable area of figure 9 may be presented as
illustrated in figure 10. As noted, the oxygen concentration at any point is obtained by
subtracting the methane and nitrogen concentrations at the point of interest from 100 as follows:
(6)
With either type of presentation, addition of methane, oxygen, or nitrogen to a particular mixture
results in formation of a series of mixtures that fall along the line between the composition point
(for example, M1 in figures 9 and 10) and the vertices of the bounding triangle. For example,
addition of methane (+CH4) to mixture M1 yields initially all mixture compositions between M1
and C (100 pct CH4). After a homogeneous mixture is produced, a new mixture composition
point, such as M2, is obtained. Similarly, if oxygen is added (+O2) to the mixture represented by
point M1, all compositions between M1 and O (100 pct O2) are obtained initially; if nitrogen is
added, all compositions between M1 and N (100 pct N2) are obtained initially. If more than one
gas is added to M1, for example, methane and oxygen, the resultant composition point may be
obtained by considering that the mixing process occurs in two steps. First, the methane is added
to M1 and the gases are mixed thoroughly to give M2. Oxygen is then added to M2 with mixing
to give a new (flammable) mixture, M3. If the methane and oxygen were added to a fixed volume
at constant pressure, some of M1 and then of M2 would escape and mix with the surrounding
atmosphere. In many instances this is an important consideration because the resulting mixtures
may be flammable. For example, even if an inert gas is added to a constant-volume tank filled
with methane, flammable mixtures can form outside the tank as the displaced methane escapes
into the atmosphere. If the methane is not dissipated quickly, a dangerous situation can arise.
When a mixture component is removed by condensation or absorption, the corresponding
composition point (for example, M1 in figures 9 and 10) shifts away from the vertices C, O, and N
along the extensions to the lines M1C, M1O and M1N, indicated in figures 9 and 10 by the
minus signs. The final composition is determined by the percentage of each component
removed from the initial mixture.
Mixtures with constant oxygen-to-nitrogen ratio (as in air), are obtained in figures 9 and 10 by
joining the apex, C, with the appropriate mixture composition along the baseline, ON. Thus, the
Air line, CA, (fig. 10) is formed by joining C with the mixture A (21 percent O2 +79 percent N2).
Using this latter point, A, one can readily determine the mixture compositions that are formed
when mixture M1 is displaced from an enclosure and mixed with air. Initially, all mixture
compositions between M1 and A would form. Since these would pass through the flammable
mixture zone, a hazardous condition would be created. Similarly, if pure combustible CH4 were
dumped into the atmosphere (air), all mixtures between C and A would form. These would
include the flammable mixtures along CA so that a hazardous condition would again be created,
unless the combustible were dissipated quickly.
Mixtures with constant oxidant content are obtained by constructing straight lines parallel to zero
oxidant line; such mixtures also have a constant combustible-plus-inert content. One particular

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
Pct O2=100 pct pct CH4 pct N2.
ANSI/ISA-TR12.13.01-1999 (R2005)
28
--`,,```,,,,````-`-`,,`,,`,`,,`---
constant oxidant line is of special importancethe minimum constant oxidant line that is tangent
to the flammability diagram or, in some cases, the one that passes through the extreme upperlimit-of-flammability value. This line gives the minimum oxidant (air, oxygen, chlorine, etc.)
concentration needed to support combustion of a particular combustible at a specified
temperature and pressure. In figures 9 and 10, the tangent line gives the minimum oxygen value
(Min O2,12 volume-percent) required for flame propagation through methane-oxygen-nitrogen
mixtures at 26C and 1 atmosphere.
Another important construction line is that which gives the maximum nonflammable combustibleto-inert ratio (critical C/N). Mixtures along and below this line form nonflammable mixtures upon
addition of oxidant. The critical C/N ratio is the slope of the tangent line from the origin (Figs. 9
and 10), 100 percent oxidant, to the lean side of the flammable mixtures curve. The reciprocal of
this slope gives the minimum ratio of inert-to-combustible at which nonflammable mixtures form
upon addition of oxidant. It is of interest in fire extinguishing.
C
10
0
90
10
20
80
30
70
-O 2
50
M1
+O 2
M3
+N 2
40
30
Air
-CH 4
nt
rce
-pe
me
olu
-N 2
50
NE
,
40
+CH4
,v
EN
ME
TH
A
+O 2
G
RO
60
NIT
vo
lum
e-p
erc
en
t
M2
60
Flammable
mixtures
70
20
80
10
90
Min O 2
Critical C/N
100
90
80
70
60
50
40
30
0
10
20
10
OXYGEN, volume-percent
Figure 9Flammability Diagram for the System Methane-Oxygen-Nitrogen at

Atmospheric Pressure and 26C.

Not for Resale
29
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 10Flammability Diagram for the System Methane-Oxygen-Nitrogen at

Atmospheric Pressure and 26C. (Data from fig. 9).
An increase in temperature or pressure usually widens the flammable range of a particular
combustible-oxidant system. The effect of temperature is shown in figure 11; two flammable
areas, T1, and T2, are defined for a combustible-inert-oxidant system at constant pressure. The
effect of temperature on the limits of flammability of a combustible in a specified oxidant was
previously shown in figure 2. This type of graph is especially useful since it gives the vapor
pressure of the combustible, the lower and upper temperature limits of flammability (TL and TU),
the flammable region for a range of temperatures, and the autoignition temperature (AIT). Nearly
20 of these graphs were presented by Van Dolah and coworkers for a group of combustibles
used in flight vehicles (218).

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
30
The lower temperature limit, TL, is essentially the flash point of a combustible, in which upward
propagation of flame is used; in general, it is somewhat lower than the flash point, in which
downward propagation of flame is used. Since TL is the intersection of the lower-limit and vaporpressure curves, a relationship can be developed between TL, or the flash point, and the
constants defining the vapor pressure of a combustible liquid. An excellent summary of such
relationships has been presented by Mullins for simple fuels and fuel blends (154).
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 11Effect of Initial Temperature on Limits of Flammability of a Combustible

Vapor-Inert-Air System at Atmospheric Pressure.

Not for Resale
31
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
% air = 100% - % JP4 vapor - % inert

U
JP-4 VAPOR, volume-percent
Flammable
mixtures
2
L
200
400
600
800
INITIAL PRESSURE, mm Hg
Figure 12Effect of Initial Pressure on Limits of Flammability of JP-4

(Jet Fuel Vapor) in Air at 26C.
At constant temperature, the flammable range of a combustible in a specified oxidant can be
represented as in figure 12. Here the flammable range of JP-4 vapor-air mixtures is given as a
function of pressure (241). A more generalized flammability diagram of a particular combustibleoxidant system can be presented in a three dimensional plot of temperature, pressure, and
combustible contentas illustrated in figure 13 (244). Here, composition is given as the ratio of
partial pressure of the combustible vapor, pVAPOR, to the total pressure, P. For any value of P, the
limits of flammability are given as a function of the temperature. For example, at 1 atmosphere
(P=1), the flammable range is bounded by the lower limit curve L1L2L3L4, and the upper limit
curve U1U2; all mixtures along the vapor pressure curve L4U3U2 are flammable. The flammable
range is the same as that depicted in figure 2. At constant temperature (for example, T1), the
flammable range is bounded by the lower limit curve L1PL1 and the upper limit curve U1PU1; the
broken curve PL1PU1 represents the low pressure, (quenched) limit.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
32
Figure 13Effect of Temperature and Pressure on Limits of Flammability of a

Combustible Vapor in a Specified Oxidant.
The flammable range is the same as that depicted in figure 12. A similar range is defined at
temperatures T2, T3, and T4 which are less than T1. However, at T3 and T4 the upper limit curves
intersect the vapor pressure curves, so that no upper limits are found above U3 and U4. In other
words, all compositions U3U3 and U4L4 are flammable. The curve L4PLU4U3U2 defines the
range of limit mixtures which are saturated with fuel vapor. Further, since L4 is the saturated
lower limit mixture at one atmosphere, T4 is the flash point.
Some of the points considered in this and the previous section are illustrated in figure 14 (232).
This is the flammability diagram for the system gasoline vapor-water vapor-air at 70F (21C) and
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
33
ANSI/ISA-TR12.13.01-1999 (R2005)
212 F (100C) and atmospheric pressure. The air saturation temperature, that is, the
temperature at which saturated air contains the quantity of water given on the water vapor axis, is
also included. For precise work, a much larger graph or an enlargement of the region from 0 to 8
percent gasoline vapor and from 0 to 30 percent water vapor would be used. However, figure 14
is adequate here. If water vapor is added to a particular mixture A, all mixture compositions
between A and pure water vapor will form as noted (if the temperature is at least 212F), and the
composition point will shift towards the 100-percent-water-vapor point. If water vapor is removed
by condensation or absorption, the composition point will move along the extension to the line
drawn from A to the 100-percent-water-vapor point. The same applies to the other components,
air and gasoline, as indicated earlier. Moreover, if more than one component is involved, the final
composition point can be found by considering the effect of each component separately.
Figure 14 is of special interest since it can be used to evaluate the hazards associated with a
gas-freeing operation. For example, mixture A represents a saturated gasoline vapor-air-water
vapor mixture at 70F. A more volatile gasoline than the one used here would give a saturated
mixture with more gasoline vapor and less air in a closed tank; a less volatile gasoline would give
less gasoline vapor and more air. In any event, if a continuous supply of air saturated with water
vapor is added to a tank containing mixture A, all compositions between A and B (air plus water
vapor) will be formed until all the gasoline vapor is flushed from the tank, and mixture B alone
remains. If steam is used to flush mixture A from the tank, all compositions between A and C will
form until all the gasoline vapor has been flushed from the tank and only steam remains (at
212F or higher). If the tank is permitted to cool, the steam will condense and air will be drawn
into the tank giving mixtures along CB. At 70F, only air plus a small amount of water vapor will
remain.
If hot water and water vapor at 175F are used to flush mixture A from the tank, the mixture
composition can only shift along AC to E. Mixtures between A and E that are flushed from the
tank mix with air to give mixtures between points along AE and B. Again, as the water vapor in
these mixtures condenses outside the tank, the composition of the resultant mixtures will shift
away from the 100-percent-water-vapor point, C. The mixture in the tank will remain at E unless
air is used to flush the tank, in which case mixture compositions between E and B will form.
Again, if the water vapor within the tank condenses, the mixture composition will shift away from
C. In any event, at this temperature (175F), the addition of air to mixture E will lead to formation
of flammable mixtures. Thus, mixture A cannot be flushed from a tank without forming flammable
mixtures, unless steam or some other inert vapor or gas is used.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
34
Figure 14Flammability Diagram for the System Gasoline Vapor-Water Vapor-Air

at 70F (21C) and at 212F (100C) and Atmospheric Pressure.
Deflagration and Detonation Processes

Once a flammable mixture is ignited, the resulting flame, if not extinguished, will either attach
itself to the ignition source or propagate from it. If it propagates from the source, the propagation
rate will be either subsonic (deflagration) or supersonic (detonation) relative to the unburned gas.
If it is subsonic, the pressure will equalize at the speed of sound throughout the enclosure in
which combustion is taking place so that the pressure drop across the flame (reaction) front will
be relatively small. If the rate is supersonic, the rate of pressure equalization will be less than the
propagation rate and there will be an appreciable pressure drop across the flame front.
Moreover, with most combustible-air mixtures, at ordinary temperatures, the ratio of the peak-toinitial pressure within the enclosure will seldom exceed about 8:1 in the former, but may be more
than 40:1 in the latter case. The pressure buildup is especially great when detonation follows a
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
35
ANSI/ISA-TR12.13.01-1999 (R2005)
large pressure rise due to deflagration. The distance required for a deflagration to transit to a
detonation depends on the flammable mixture, temperature, pressure, the enclosure, and the
ignition source. With a sufficiently powerful ignition source, detonation may occur immediately
upon ignition, even in the open. However, the ignition energy required to initiate a detonation is
usually many orders of magnitude greater than that required to initiate a deflagration (32, 249).
DEFLAGRATION
Where a deflagration occurs in a spherical enclosure of volume V with central ignition, the
approximate pressure rise DP at any instant t after ignition is given by the expressions:
3 3
Su t
DP = KP 1 --------- P m,
V
(7)
nb Tb
M1 Tb
P m = P1 ----------- = P 1 ------------n1 T1
Mb T1
(8)
and
where K is a constant, Su is the burning velocity, P1 is the initial pressure Pm is the maximum
pressure, T1 is the initial temperature, n1 is the number of moles of gas in the initial mixture, nb is
the number of moles of gas in the burned gases, M 1 is the average molecular weight of the initial
mixture, M b is the average molecular weight of the burned gases, and Tb is the final (adiabatic)
temperature of the products. With other enclosures, or with noncentral ignition, the flame front is
disturbed by the walls before combustion is completed, so that calculated pressure cannot be
expected to approximate actual pressure. Even with spherical enclosures, the flame front is not
actually spherical, so that the walls tend to disturb the flame before combustion is complete (118,
130). A graph of the pressure developed by the combustion of a stoichiometric methane-air
mixture (central ignition) in a 19.7 cm diameter, 9-liter cylinder is given in figure 15. The
calculated pressure for a 9-liter sphere is included for comparison; K in equation (7) was
evaluated from the experimental curve at 70 milliseconds. The calculated curve follows the
experimental curve closely about 75 milliseconds, when the latter curve has a break. This
suggests that the flame front was affected by the cylinder walls in such a way that the rate of
pressure rise decreased, and the experimental curve fell below the calculated curve. Further,
since the combustion gases were being cooled, the maximum pressure fell below the calculated
value. The minimum elapsed time (in milliseconds) required to reach the maximum pressure
appears to be about 75 3 V for the paraffin hydrocarbons and fuel blends such as gasoline; V is
the volume in cubic feet in this case.
DETONATION
Wolfson and Dunn (52, 230) have expressed the pressure ratio P2/P1 across a detonation front
as
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
36
P2
1
2
------ = -------------- ( g 1 M 1 + 1 ),
g2 + 1
P1
(9)
where g2 is the specific heat ratio of the burned gases, g1 is the specific heat ratio of the initial
mixture, and M1, is the Mach number of the detonation wave with respect to the initial mixture.
M1 is given in terms of the temperatures T and molecular weights W of the initial and final
mixtures by the expression:
2
( g1 M1 + 1 )
( g2 + 1 ) T2 W1
---------------------------=
----------------------------------- .
2
g2 T1 W2
g1 M1
(10)
Wolfson and Dunn have developed generalized charts that simplify the operations involved in
obtaining the pressure ratio as well as the density and temperature/molecular weight ratios
across the detonation wave and the energy release in the detonation wave.
--`,,```,,,,````-`-`,,`,,`,`,,`---
Many investigators have measured and calculated detonation and reflected pressures resulting
from detonation waves (54, 57, 204). Figure 16 from the data of Stoner and Bleakney (204) gives
the detonation velocity, the static or detonation pressure, and the reflected pressure developed
by a detonation wave propagating through hydrogen-oxygen mixtures at atmospheric pressure
and 18C.
100
Pm
Calculated
(9-liter sphere)
PRESSURE RISE, psi
80
Experimental
(9-liter cylinder)
60
40
20
40
80
120
ELAPSED TIME, milliseconds
160
Figure 15Pressure Produced by Ignition of a 9.6 Volume-Percent Methane-Air

Mixture in a 9-Liter Cylinder (Experimental).

Not for Resale
37
ANSI/ISA-TR12.13.01-1999 (R2005)
BLAST PRESSURE
The pressures produced by a deflagration or a detonation are often sufficient to demolish an
enclosure (reactor, building, etc.). As noted, a deflagration can produce pressure rises in excess
of 8:1, and pressure rises of 40:1 (reflected pressure) can accompany a detonation. As ordinary
structures can be demolished by pressure differentials of 2 or 3 psi, it is not surprising that even
reinforced concrete structures have been completely demolished by explosions of near-limit
flammable mixtures.
50
3,500
V
45
Pr (theoretical)
40
3,000
35
Pr (experimental)
2,500
25
Ps (experimental)
P, atm
V , m / sec
30
20
15
2,000
10
5
0
1,500
20
30
40
50
60
70
80
90
H 2 , volume-percent
Figure 16Detonation Velocity, V; Static Pressure, Ps; and Reflected Pressure, Pr,
Developed by a Detonation Wave Propagating Through Hydrogen-Oxygen
Mixtures in a Cylindrical Tube at Atmospheric Pressure and 18C.
Jacobs and coworkers have studied the damage potential of detonation waves in great detail (91,
170). They have considered the principles involved in rupturing of pipes and vessels by
detonations and the relevance of engineering and metallurgical data to explosions. More
recently, Randall and Ginsburg (171) have investigated bursting of tubular specimens at ordinary
and reduced temperatures. They found that the detonation pressure required to burst such
specimens was, in general, slightly higher than the corresponding static-bursting pressure.
Ductility of the test specimen appeared to have little effect on the bursting pressure, but ductility
increased the strength of pipes containing notches or other stress raisers.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
38
When a detonation causes an enclosure to fail, a shock wave may propagate outward at a rate
determined by characteristics of the medium through which it is transmitted, and the available
energy. If the shock velocity, V, is known, the resulting overpressure, (P Po), is given by the
expression (204)
2g
P P o = Po ----------g1
V
--- 1 ,
a
(11)
where g is the ratio of specific heats, and a is the velocity of sound in the medium through which
the shock wave passes. The approximate damage potential can be assessed from the data in
table 1 (217).
In conducting experiments in which blast pressures may be generated, special precautions must
be taken to protect the personnel and equipment from blast and missiles. Browne, Hileman, and
Weger (16) have reviewed the design criteria for suitable barricades. Other authors have
considered the design of suitable laboratories and structures to prevent fragment damage to
surrounding areas (44, 174, 203, 220).
Table 1 Conditions of failure of peak over pressure-sensitive elements (217)

Structural element
Failure
Approximate incident blast

overpressure (psi)
Glass windows, large and small.
Usually shattering, occasional

frame failure.
0.5-1.0
Corrugated asbestos siding.
Shattering.
1.0-2.0
Corrugated steel or aluminum

paneling.
Connection failure, followed by

buckling.
1.0-2.0
Wood siding panels, standard

house construction.
Usually failure occurs at main

connections, allowing a whole
panel to be blown in.
1.0-2.0
Concrete or cinderblock wall

panels, 8 or 12 inches thick (not
reinforced).
Shattering of the wall.
2.0-3.0
Brick wall panel, 8 or 12 inches

thick (not reinforced).
Shearing and flexure failures.
7.0-8.0
Preventive Measures
INERTING
In principle, a gas explosion hazard can be eliminated by removing either all flammable mixtures
or all ignition sources (23, 240). However, this is not always practical, as many industrial
operations require the presence of flammable mixtures,and actual or potential ignition sources.
Accordingly, special precautions must be taken to minimize the damage that would result if an
accidental ignition were to occur. One such precaution involves the use of explosive actuators
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
39
ANSI/ISA-TR12.13.01-1999 (R2005)
which attempt to add inert material at such a rate that an explosive reaction is quenched before
structural damage occurs (70, 72). Figure 17 shows how the pressure varies with and without
such protection. In the latter case, the pressure rise is approximately a cubic function of time, as
noted earlier. In the former case, inert is added when the pressure or the rate of pressure rise
exceeds a predetermined value. This occurs at the time ti in figure 17 when the explosive
actuators function to add the inert. As noted, the pressure increases momentarily above the
value found in the unprotected case and then falls rapidly as the combustion reaction is
quenched by the inert.
FLAME ARRESTORS AND RELIEF DIAPHRAGMS
Inert atmospheres must be used when not even a small explosive reaction can be tolerated.
However, when the ignition of a flammable mixture would create little hazard if the burning
mixture were vented, flame arrestors and relief diaphragms could be used effectively. The
design of such systems is determined by the size and strength of the confining vessels, ducts,
etc.
In recent studies of the efficiency of wire gauze and perforated block arrestors (161, 162), Palmer
found the velocity of approach of the flame to be the major factor in determining whether flame
passed through an arrestor. For these two types of arrestors, he found the critical approach
velocity to be
1.75k ( T h T o )
-,
V = ----------------------------------0.9
m Q xo
(12)
9.6kAt ( T h T o )
-,
V = ---------------------------------------2
d Q xo
(13)
and
--`,,```,,,,````-`-`,,`,,`,`,,`---
where k is the thermal conductivity of the gas; m is the mesh width; Th is the mean bulk
temperature of the flame gases through the arrestor; To is the initial temperature of the arrestor;
Q is the heat lost by unit area of flame; xo is the thickness of the flame propagating at the burning
velocity, S; d is the diameter of an aperture; A is the area of a hole in unit area of the arrestor
face; and t is the arrestor thickness.
Equations (12) and (13) can be used to determine the mesh width or aperture diameter needed
to stop a flame having a particular approach velocity. In practice, application of these equations
assumes a knowledge of the flame speed in the system of interest. Some useful data have been
made available by Palmer and Rasbash and Rogowski (172, 173), as well as by Jost (118) and
Lewis and von Elbe (130).

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
40
Figure 17Pressure Variation Following Ignition of a Flammable Mixture in

Unprotected and Protected Enclosures.
Tube bundles also may be used in place of wire screens. Scott found that these permit
increased aperture diameters for a given approach velocity (192).
In practice, it may be desirable to install pressure relief vents to limit damage to duct systems
where flame may propagate. Rasbash and Rogowski (173) found that with propane-and
pentane-air mixtures, the maximum pressure PM, (pounds per square inch) developed in an
open-ended duct, having a cross section of 1 ft2 is:
L
L
PM = 0.07 ---- , and 6 ---- 48 ,
D
D
(14)
Lwhere --D is the ratio of duct length to diameter. However, the presence of an obstacle (bend,
constriction, etc.) in the path of escaping gases increased the pressure due to resistance to fluid
flow by the obstacle. Location of a relief vent near the ignition source decreased the maximum
pressure as well as the flame speed. For values of K (cross-section area of duct/area of vent)
greater than 1, these authors found
0.8K P M 1.8K ,
(15)
Lwhere 2 K 32 , and 6 --D 30 . To keep the pressure at a minimum either many small vents
or a continuous slot was recommended rather than a few large vents. In addition, vents should
be located at positions where ignition is likely to occur and should open before the flame has
traveled more than 2 feet.
When possible, relief vents should be used with flame arrestors. The vents tend not only to
reduce the pressure within a system following ignition but also to reduce the flame speed, thus
making all arrestors more effective. Unfortunately, in certain large applications (for example,
drying ovens), it is difficult to use flame arrestors effectively. In such cases, greater reliance must
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
41
ANSI/ISA-TR12.13.01-1999 (R2005)
be placed on the proper functioning of relief vents. Simmonds and Cubbage (42, 43, 195) have
investigated the design of effective vents for industrial ovens. They found two peaks in the
pressure records obtained during the venting of cubical ovens (fig. 18). The first peak, P1; the
oven volume, V; the factor, K; and the weight per unit area (lb/ft2) of relief, w, were related as
follows for a 25 percent town gas"-air mixture:
P1 V
13
= 1.18Kw + 1.57 .
(16)
= S o ( 0.3Kw + 0.04 ) ,
(17)
More generally,
P1V
13
where So is the burning velocity of the mixture at the oven temperature.

The first pressure pulse was ascribed to the release and motion of the relief vent following
ignition; the second pulse, to continued burning at an increased rate. The second pulse
represents the pressure drop across the vent, and it is thus proportional to K. For small values of
K it was found that
P2 = K.
(18)
As with ducts, larger pressures were obtained when obstructions were placed in the oven.
Figure 18Pressure Produced by Ignition of a Flammable Mixture in

a Vented Oven.
"
Town gas contained approximately 52% hydrogen, 17% carbon monoxide, 15% methane; the balance
was other hydrocarbons, 3%; nitrogen 9%; carbon dioxide, 3%; and oxygen.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
42
--`,,```,,,,````-`-`,,`,,`,`,,`---
In designing explosion reliefs for ovens, Simmonds and Cubbage pointed out that (1) the reliefs
should be constructed in such a way that they do not form dangerous missiles if an explosion
occurs; (2) the weight of the relief must be small so that it opens before the pressure builds up to
a dangerous level; (3) the areas and positions of relief openings must be such that the explosion
pressure is not excessive; (4) sufficient free space must be utilized around the oven to permit
satisfactory operation of the relief and minimize risk of burns to personnel; and (5) oven doors
should be fastened securely so that they do not open in the event of an explosion.
Burgoyne and Wilson have presented the results of an experimental study of pentane vapor-air
explosions in vessels of 60- and 200-cubic-foot volume (30). They found the rates of pressure
rise greater than could be predicted from laminar burning velocity data, so that the effect of a
relief area in lowering the peak pressure was less than expected. All experiments were
conducted at an initial pressure of 1 atmosphere. Vent data for use at higher initial pressures are
summarized in an article by Block (10); a code for designing pressure relief systems has been
proposed in this article. Other authors have considered the effects of temperature and
characteristics of the flammable mixture on vent requirements (14, 35, 38, 45, 46, 134, 145,
168, 221).
Flammability Characteristics
The flammability data (limits of flammability, flash point, ignition temperature and burning
velocity) of the various chemical families exhibit many similarities. Accordingly, the data
presented here are grouped under the various commercially important families, blends, and
miscellaneous combustibles.
PARAFFIN HYDROCARBONS (CnH2n+2)
Limits in Air
Lower and upper limits of flammability at 25C (or at the temperature noted) and 1 atmosphere
(L25 and U25) for many members of the paraffin hydrocarbon series are given in table 2, together
with the molecular weight, M, vapor specific gravity, sp gr, stoichiometric composition in air, Cst
(appendix B) and heat of combustion, DHc (183). At room temperature and atmospheric or
reduced pressure, the lower limits of flammability of most of this series fall in the range from 45 to
50 mg combustible vapor per liter of air at standard conditions, that is, 0C and 760 mm Hg
(0.045 to 0.050 oz combustible vapor per cubic foot of air) (247). This is illustrated in figure 19 in
which some lower limits of flammability are plotted against molecular weight; except for methane,
ethane, and propane all limit values fall in a band between concentrations of approximately 45
and 50 mg/lr.
The following expression may be used to convert from a lower limit L in volume-percent of vapor
in the vapor-air mixture to one in milligrams of combustible, per liter of air at standard conditions:
mg
L (vol pct)
L ------- = -------------------------------------------------------------------------- ,
1
1
[ 100 L (vol pct) ] sp vol ------mg

Not for Resale
(19)
43
ANSI/ISA-TR12.13.01-1999 (R2005)
specific volume being volume of combustible vapor per milligram of combustible. At standard
conditions (0C and 760 mm Hg) this is about 22.414/1,000M, where M is the molecular weight of
the combustible. Since L (vol pct) of most members of this series is much less than 100 percent,
the lower limit can be expressed as
mg
L ------- 0.45ML (vol pct) .
1
(20)
At any specified temperature, the ratio of the lower limit to the amount of combustible needed for
complete combustion, Cst, also is approximately constant. This was first noted by Jones (95) and
later by Lloyd (133), who found that for paraffin hydrocarbons at about 25C,
L 25 0.55C st .
(21)
For the complete combustion of the paraffin hydrocarbons, we have:
C n H 2n + 2 + ( 1.5n + 0.5 )O 2 nCO2 + ( n + 1 )H 2 O ,
(22)
100
C st = ---------------------------------------------------- vol pct ,
1 + 4.773 ( 1.5n + 0.5 )
(23)
so that in air
where 4.773 is the reciprocal of 0.2095, the molar concentration of oxygen in dry air. The values
of Cst (appendix B) are included in table 2. By weight these become
1000 [ 12.01n + 1.008 ( 2n + 2 ) ] mg

C st = ---------------------------------------------------------------------------- ------- ,
22.414 4.773 ( 1.5n + 0.5 ) 1
(24)
14.03n + 2.02 mg
C st = 9.34 --------------------------------- ------- .
1.5n + 0.5
1
(25)
--`,,```,,,,````-`-`,,`,,`,`,,`---
or

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
44
Figure 19Effect of Molecular Weight on Lower Limits of Flammability of Paraffin

Hydrocarbons at 25C.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
45
ANSI/ISA-TR12.13.01-1999 (R2005)
Table 2 Properties of paraffin hydrocarbons

Lower limit in air
Combustible
Formula
Sp gr
(Air=1)
Cst in air
(vol pct)
Net
DHc
Kcal
-)
( ----------mole
L25
(vol pct)
Upper limit in air

Ref.
------- )
L ( mg
1
L
25
--------C
st
U25
(vol pct)
Ref.
------- )
U ( mg
1
U
25
---------C
st
Methane
CH4
16.04
0.55
9.48
191.8
5.0
0.53
38
(40)
15.0
1.6
126
(40)
Ethane
C2H6
30.07
1.04
5.65
341.3
3.0
.53
41
(40)
12.4
2.2
190
(41)
Propane
C3H8
44.09
1.52
4.02
488.5
2.1
.52
42
(115)
9.5
2.4
210
(41)
n-Butane
C4H10
58.12
2.01
3.12
635.4
1.8
.58
48
(113)
8.4
2.7
240
(41)
n-Pentane
C5H12
72.15
2.49
2.55
782.0
1.4
.55
46
(40)
7.8
3.1
270
(40)
n-Hexane
C6H14
86.17
2.98
2.16
928.9
1.2
.56
47
(246)
7.4
3.4
310
(40)
n-Heptane
C7H16
100.20
3.46
1.87
1075.8
1.05
.56
47
(246)
6.7
3.6
320
(40)
n-Octane
C8H18
114.23
3.94
1.65
1222.8
.95
.58
49
(246)
n-Nonane
C9H20
128.25
4.43
1.47
1369.7
.85
.58
49
(246)
n-Decane
C10H22
142.28
4.91
1.33
1516.6
.75
.56
48
(246)
5.6
4.2
380
--`,,```,,,,````-`-`,,`,,`,`,,`---
n-Undecane
C11H24
156.30
5.40
1.22
1663.6
.68
.56
48
(4)
n-Dodecane
C12H26
170.33
5.88
1.12
1810.5
.60
.54
46
(4)
n-Tridecane
C13H28
184.36
6.37
1.04
1957.4
.55
.53
46
(4)
n-Tetradecane
C14H30
198.38
6.85
.97
2104.3
.50
.52
44
(4)
n-Pentadecane
C15H32
212.41
7.33
.90
2251.2
.46
.51
46
(4)
n-Hexadecane
C16H34
226.44
7.82
.82
2398.2
.43
.51
44
(4)
t=43 C.
t=53 C.
t=86 C.
4
Calculated value extrapolated to 25C at Explosives Res. Center, Federal Bureau of Mines.
2
3

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
46
Thus,
C st 87 mg/1, n4.
(26)
Combining this equation with equation (21), we have
mg
mg
L 25 ------- 48 ------- ,
1
1
for paraffin hydrocarbons, except methane, ethane, and propane. Substitution of this value into
equation (20) gives
107
L 25 (vol pct) --------- .
M
(28)
The following expression may be used to convert a lower limit value in volume-percent to a fuelair (weight) ratio:
L (vol pct)
M
L ( F A ) = ------------- ---------------------------------------- .
28.96 100 L (vol pct)
(29)
The reciprocal expression gives the air-fuel (weight) ratio:
100
28.96
L ( A F ) = ------------- ------------------------- 1
M L (vol pct)
(30)
As noted, the lower limits given in figure 19 were determined at room temperature and
atmospheric or reduced pressure. Lower limits vary with temperature as shown for methane in
figure 20. The limit values obtained with upward propagation of flame (21) fall fairly close to a
straight line that passes through the lower limit value at 25C and the flame temperature
(1,225C). This is in accordance with the White criterion that the flame temperature is constant
at the lower limit (222). The data obtained by White with downward propagation of flame fall
along a line parallel to the line through the limit values obtained with upward propagation. Taking
the value 1,300C as the approximate flame temperature for the paraffin hydrocarbon series (55),
and using the lower limit values at room temperature in table 2, the limits of the first 10 paraffin
hydrocarbons are represented as in figures 21 and 22. Figure 21 gives the lower limits in
volume-percent and figure 22 in milligrams per liter. By weight, the lower limits of most members
of this series again fall in a fairly narrow band ("higher hydrocarbons" region). Individual adiabatic
flame temperatures can be determined for lower limit mixtures using the data in table 2 and
appendix C (55).
The straight lines of figures 21 and 22 are given by:
L 25
L t = L 25 ----------------------------- ( t 25 ) ,
1300 25
(31)
Lt
--------- = 1 0.000784 ( t 25 ) .
L 25
(32)
or

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
(27)
47
ANSI/ISA-TR12.13.01-1999 (R2005)
They are described in more general terms by a plot of Lt,/L25 against the temperature (fig. 23,
solid line).
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 20Effect of Temperature on Lower Limit of Flammability of Methane in Air

at Atmospheric Pressure.
These data are also correlated fairly well with the modified Burgess-Wheeler Law suggested by
Zabetakis, Lambiris, and Scott (242):
0.75
L t = L 25 ---------- ( t 25 ) ,
DH c
(33)
where t is the temperature in C and DHc is the net heat of combustion in kilocalories per mole.
Then,
Lt
0.75
---------- = 1 ------------------------- ( t 25 ) .
L 25 DH c
L 25
Substituting the value 1,040 for L25DHc obtained by Spakowski (201), we have

Not for Resale
(34)
ANSI/ISA-TR12.13.01-1999 (R2005)
48
Lt
---------- = 1 0.000721 ( t 25 ) ,
L 25
(35)
which is also given in figure 23 for a limited temperature range with the broken line.
Only the lower limit at 25C and atmospheric pressure is needed to use figure 23. For example,
assuming a constant flame temperature, the ratio Lt /L25 at 600C is 0.55. The calculated lower
limit of methane at 600C therefore is 5.0 x 0.55, or 2.75 volume-percent. The same value can
be obtained directly from figure 21. From the modified Burgess-Wheeler Law curve,
Lt /L25=0.585 at 600C, so that L600=2.92 volume-percent.
Figure 21Effect of Temperature on Lower Limits of Flammability of 10 Paraffin

Hydrocarbons in Air at Atmospheric Pressure.
Limit-of-flammability measurements are complicated by surface and vapor-phase reactions that
occur at temperatures above the autoignition temperature. For example, Burgoyne and Hirsch
(25) have shown that methane-air mixtures containing up to 5 percent methane burn readily at
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
49
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
1,000 C. Experiments were conducted with mixtures containing as little as 0.5 percent methane;
figure 20 predicts that a flame would not propagate through such a mixture.
Flammability experiments at elevated temperatures indicate that in the absence of cool flames
(87, 88), the upper limit also increases linearly with temperature. The effect of temperature
appears to be fairly well correlated by the modified Burgess-Wheeler law:
0. 75
U t = U 25 + ---------- ( t 25 ) .
DH c
(36)
If we assume that the heat release at the upper limit is equal to that at the lower limit, then
Ut
---------- = 1 + 0.000721 ( t 25 ) .
U 25
(37)
A plot of Ut /U25 against temperature (fig.24) was used to compare recent experimental values of
Rolingson and coworkers (182) for methane-air mixtures at 15 psig with those predicted by the
modified Burgess-Wheeler law. The experimental and calculated upper limits are given in table 3
together with the difference, Ucalc Uexper. In each case, the difference is less than 4 percent of
the experimental value, which is approximately within the limit of experimental error. Earlier
experiments of White (222) at temperatures to 400 C, with downward flame propagation, also
are represented quite adequately by equation (37). For example, White found that the upper limit
of pentane in air (downward propagation) increased linearly from 4.50 volume-percent at about
17 C to 5.35 volume-percent at 300 C. The ratio of 5.35: 4.50 is 1.17, which compares quite
well with U300/U251.20 obtained from figure 24.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
50
Figure 22Effect of Temperature on Lower Limits of Flammability of 10 Paraffin

Hydrocarbons in Air at Atmospheric Pressure by Weight.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
51
ANSI/ISA-TR12.13.01-1999 (R2005)
Given the vapor pressure curve and the lower limit of flammability, the lower temperature limit or
approximate flash point of a combustible can be calculated from either equation (32) or (35)
(218). Approximate flash points were obtained previously, using only the vapor pressure curve
and the lower limit at ordinary or elevated temperatures (154). The values obtained with this
procedure are somewhat low because the lower limit at any temperature above the flash point is
less than at the flash point. The lower temperature limits of paraffin hydrocarbon at atmospheric
pressure are given in table 4.
Table 3 Upper flammability limits, U, of methane-air mixtures at 15 psig.

Uexper1 (vol percent)
Ucalc (vol percent)
UcalcUexper
(vol percent)
25
15.5
15.5
100
16.3
16.4
.1
200
17.0
17.5
.5
300
17.9
18.6
.7
(182).
--`,,```,,,,````-`-`,,`,,`,`,,`---
Temperature (C)

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
52
--`,,```,,,,````-`-`,,`,,`,`,,`---
Moderate changes in pressure do not ordinarily affect the limits of flammability of the paraffins in
air, as shown in figure 25 for pentane, hexane, and heptane in air (241) in a range from 75 to 760
mm Hg. The lower limits coincide, but the upper limits, by weight, increase with increasing
molecular weight.
Table 4 Lower temperature limits and autoignition temperatures of paraffin

hydrocarbons at atmospheric pressure.
Lower temperature limit
In air
In air
In oxygen
Ref.
Ref.
Methane
187
305
(1)
537
999
(158)
Ethane
130
202
(1)
515
959
(237)
506
943
466
871
(158)
Ref.
(94)
Propane
102
152
(1)
n-Butane
72
96
(1)
405
761
(237)
283
542
(191)
Isobutane
81
114
(1)
462
864
(158)
319
606
(94)
n-Pentane
48
54
(1)
258
496
(194)
258
496
(144)
n-Hexane
26
15
(159)
223
433
(194)
225
437
(94)
n-Heptane
25
(159)
223
433
(237)
209
408
(94)
n-Octane
13
56
(159)
220
428
(237)
208
406
(191)
n-Nonane
31
88
(159)
206
403
(237)
n-Decane
46
115
(159)
208
406
(237)
202
396
n-Dodecane
74
165
(159)
204
399
(237)
126
259
(1)
205
401
(237)
n-Hexadecane
1
Autoignition temperature
Calculated value

Not for Resale
(94)
53
ANSI/ISA-TR12.13.01-1999 (R2005)
1.2
1.0
Modified Burgess-Wheeler Law
L t /L 25
.8
.6
.4
Constant flame temperature
.2
0
-200
200
400
600
800
1,000
1,200
1,400
TEMPERATURE, C
Figure 23Effect of Temperature on Lt /L25 Ratio of Paraffin Hydrocarbons in Air

By volume, at atmospheric pressure and 25C, Spakowski (201) found that the upper and lower
limits were related by the expression:
0.56
U 25 = 7.1L 25 .
(38)
However, the data presented here are correlated more precisely by a somewhat simpler
expression:
U 25 = 6.5 L 25 .
(39)
Neither expression is applicable when cool flames are obtained. Substitution of equation (21) for
L25 into equation (39) gives
U 25 = 4.8 C st .
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
(40)
ANSI/ISA-TR12.13.01-1999 (R2005)
54
1.4
U t /U25
1.3
1.2
1.1
1.0
0
100
200
300
400
500
TEMPERATURE, C
Figure 24Effect of Temperature on Ut /U25 Ratio of Paraffin Hydrocarbons in Air

at Atmospheric Pressure in the Absence of Cool Flames.
The limits of flammability of natural gas (85-95 pct methane and 15-5 pct ethane) have been
determined over an extended pressure range by Jones and coworkers (78, 105). They are given
in figure 26 for pressures from 1 to 680 atmospheres (10,000 psig). An analysis of these data
shows the limits vary linearly with the logarithm of the initial pressure. That is,
L (vol pct)=4.90.71 log P (atm),
(41)
U (vol pct)=14.1+20.4 log P (atm),
(42)
and
with a standard error of estimate of 0.53 vol pct for L and 1.51 vol pct for U.
Although the limits of flammability are not affected significantly by moderate changes in pressure,
the temperature limits are pressure dependent. As the total pressure is lowered, the partial
pressure of the combustible must also be lowered to maintain a constant combustible
concentration.
The effect of pressure on the lower temperature limit of the normal paraffins pentane, hexane,
heptane, and octane in air, for pressures from 0.2 to 2 atmospheres, is shown in figure 27. The
temperature limits were calculated from the L25 values, the vapor pressure curves, and the data
of figure 23.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
55
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 25Effect of Pressure on Limits of Flammability of Pentane, Hexane, and

Heptane in Air at 26C.
Limits in Other Atmospheres
--`,,```,,,,````-`-`,,`,,`,`,,`---
Limits of flammability of some paraffin hydrocarbons have been determined in oxygen, chlorine,
and oxides of nitrogen, as well as in mixtures of air and various inerts. The lower limits in oxygen
and in a wide variety of oxygen-nitrogen mixtures are essentially the same as those in air at the
same temperature and pressure (fig. 10). Limit-of-flammability measurements by Bartkowiak
and Zabetakis for methane and ethane in chlorine at 1, 7.8, and 14.6 atmospheres, ranging from
25 to 200 C, are summarized in tables 5 and 6 (8).

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
56
Coward and Jones (40) have presented graphically the limits of flammability of the first six
members of the paraffin series in air containing various inerts, based on a representation found
useful in some mining applications and treating inert gas or vapor as part of the atmosphere with
which the combustible is mixed. The composition of a point on such a diagram, except one that
represents only combustible and air, cannot be read directly. Instead, one must determine the
composition of the atmosphere, add the combustible content, and then compute the total mixture
composition.
Table 5 Limits of flammability of methane in chlorine (volume-percent)

Pressure,
psig
Limits
Temperature, C
25
100
200
Lower
Upper
5.6
70
3.6
66
0.6
100
Lower
Upper
72
2.4
76
6
77
200
Lower
Upper
73
72
75
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
57
ANSI/ISA-TR12.13.01-1999 (R2005)
60
%air = 100% - % natural gas
NATURAL GAS, volume-percent
50
40
Fammable mixtures
30
20
10
100
200
300
400
500
600
700
800
INITIAL PRESSURE, atmospheres
Figure 26Effect of Pressure on Limits of Flammability of Natural Gas

in Air at 28C.
--`,,```,,,,````-`-`,,`,,`,`,,`---
This has been done for methane through hexane (figs. 28-33). Compositions are determined
directly from the abscissas (inert concentration) and ordinates (combustible concentration); the
air in any mixture is the difference between 100 percent and the sum of inert and combustible.
Data of Burgoyne and Williams-Leir for methane-methyl bromide (MeBr)-air and methane-carbon
tetrachloride-air mixtures are included in figure 28 (29). Unfortunately, the methane-methyl
bromide-air data were obtained in a 1 7/8-inch tube. Although satisfactory for methane and other
hydrocarbons, this tube is apparently not satisfactory for many of the halogenated hydrocarbons.
Thus a recent industrial explosion involving methyl bromide prompted Hill to reconsider the
flammability of methyl bromide in air (84). He found that methyl bromide was not only flammable
in air but that it formed flammable mixtures at 1 atmosphere with a wider variety of
concentrations than Jones had reported (96). This would suggest that there is no justification for
the assumption that Jones' flammability data for methyl bromide were influenced by the presence
of mercury vapor (196). Hill's limit values at atmospheric pressure are included in figure 28 and
are used to form the approximate, broken, flammability curves for the methane-methyl bromideair system.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
58
Figure 27Effect of Pressure on Lower Temperature Limits of Flammability of

Pentane, Hexane, Heptane, and Octane in Air.
Table 6 Limits of flammability of ethane in chlorine (volume-percent)
Limits
Temperature, C
25
100
200
Lower
Upper
6.1
58
2.5
48
2.5
100
Lower
Upper
3.5
63
1.0
75
1.0
82
200
Lower
Upper
66
73
76
Data of Moran and Bertschy for pentane-perfluorpropane-air, pentane-sulfur hexafluoride-air and

pentane-perfluoromethane-air mixtures are included in figure 32 (147). Data by Burgoyne and
Williams-Leir for hexane-methyl bromide-air and hexane-Freon-12" (F12; CF2Cl2)-air mixtures
have been included in figure 33. These data were all obtained in 1 7/8-inch-diameter tubes. An
investigation of flammability of hexane-methyl bromide-air mixtures in a 4-inch tube indicated that
"
Trade names are used for identification only; this does not imply endorsement by the Bureau of Mines.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
Pressure,
psig
59
ANSI/ISA-TR12.13.01-1999 (R2005)
an increase in tube size (from 1 7/8-inches to 4-inches-ID) resulted in a narrowing of the

flammable range; the upper limit decreased from 7.5 to 5.7 volume-percent n-hexane vapor in air
while the lower limit remained constant. The amount of methyl bromide required for extinction
decreased from 7.05 volume-percent in the 1 7/8-inch tube to 6.0 volume-percent in the 4-inch
tube. However, again this is not in line with the results obtained by Hill with methyl bromide-air
mixtures (84). Accordingly, while the data obtained in approximately 2-inch tubes were used to
construct figure 33, the Hill data, obtained in a larger apparatus, are also used to form the
approximate, broken, flammability curves for the hexane-methyl bromide-air system.
The limits of flammability diagrams for the system n-heptane-water vapor-air at 100 and 200C
(fig. 34) show the effects of temperature on a system that produces both normal and cool flames
at atmospheric pressure (192). Interestingly enough, the minimum oxygen requirement for flame
propagation (Min O2) at 200C is the same for the cool and normal flame regions in this instance.
Further, the decrease in minimum oxygen requirements (from 13.50.3 volume-percent at 100C
to 12.80.3 volume-percent at 200C) is within the range predicted by the modified BurgessWheeler law (equation 35 and fig. 23). However, the available data are too meager at present to
permit a realistic evaluation of the validity of this law.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
60
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 28Limits of Flammability of Various Methane-Inert Gas-Air Mixtures at

25C and Atmospheric Pressure.
Inspection of the limit-of-flammability curves in figures 28 to 33 reveals that except for methane
and ethane, the minimum amounts of carbon dioxide and nitrogen required for flame extinction
(peak values) at 25C and atmospheric pressure are about 28 and 42 volume-percent,
respectively. The ratio of these values is approximately inversely proportional to the ratio of their
heat capacities at the temperature at which combustion occurs. Accordingly, generalized
flammability diagrams of the type given in figure 35 can be constructed for the higher
hydrocarbons, ignoring the presence of cool flames. Such diagrams do not appear to be
applicable to the halogenated hydrocarbons since these materials tend to decompose even in
flames of limit-mixture composition and, as noted, may themselves propagate flame. Coleman

Not for Resale
61
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
(37) has found that the ratios of the peak values of a halogenated hydrocarbon are not constant
but are proportional to the heats of combustion of the combustibles to which the halogenated
hydrocarbon is added.
Figure 29Limits of Flammability of Ethane-Carbon Dioxide-Air and

Ethane-Nitrogen-Air Mixtures at 25C and Atmospheric Pressure.
Few data are available for the effects of pressure on the limits of flammability of combustibleinert-air mixtures. One such set of data is summarized in figure 36, which gives the limits of
flammability of natural gas (85 pct methane+15 pct ethane) nitrogen-air at 26 C and 0, 500,
1,000 and 2,000 psig (105). Similar data are given for ethane-carbon dioxide-air (fig. 37) and
ethane-nitrogen-air (fig. 38) (121), and for propane-carbon dioxide-air (fig. 39) and propanenitrogen-air (fig. 40) (122). Minimum oxygen requirements for flame propagation (min O2)
through natural gas-nitrogen-air, ethane-nitrogen-air, and propane-nitrogen-air at atmospheric

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
62
--`,,```,,,,````-`-`,,`,,`,`,,`---
and elevated pressures and 26 C are summarized in figure 41. The minimum O2 values in
volume-percent are related to pressure as follows:
For natural gas:
Min. O2=13.981.68 log P;
(43)
For ethane:
Min. O2=12.601.36 log P; and
(44)
For propane:
Min. O2= 13.29 1.52 log P;
(45)
where P is the initial pressure in psia.
Figure 30Limits of Flammability of Propane-Carbon Dioxide-Air and

Propane-Nitrogen-Air Mixtures at 25C and Atmospheric Pressure.
The lower limit of flammability of any mixture of the paraffin hydrocarbons can be calculated by
Le Chatelier's law (40, 129, 235):

Not for Resale
63
ANSI/ISA-TR12.13.01-1999 (R2005)
100
L = -------------- , C i = 100
n
Ci i = 1
---L
i=1 i
(46)
where Ci and Li are the percentage composition and lower limit, respectively, of the ith
combustible in the mixture. For example, a mixture containing 80 volume-percent methane,
15 volume-percent ethane and 5 volume-percent propane has a lower limit in air at 25C and
atmospheric pressure of:
100
L 25 = ------------------------------------ = 4.3 vol pct .
80 15
5
------- + ------- + ------5.0 3.0 2.1
(47)
Liquid mixtures can be treated in the same way if the relative escaping tendencies of the various
components are known. Since the paraffin hydrocarbons obey Raoult's law (143), the partial
pressure of each component can be calculated as follows:
pi = poNi
(48)
--`,,```,,,,````-`-`,,`,,`,`,,`---
where pi is the vapor pressure of the ith component in the blend, po is the vapor pressure of the
pure component and Ni is its mole fraction in the solution. This procedure has been used to
calculate the lower temperature limits of decane-dodecane blends in air (fig. 42). The vapor
pressures of decane and dodecane and the calculated low temperature limits are given by solid
lines and four experimental values by circles.
Autoignition
Two types of autoignition data are obtained depending upon whether the objective is to cause or
to prevent the ignition of a combustible in air. The first type are usually obtained at high
temperatures, where the ignition delay is relatively short. Typical of these are the data of Mullins
(153), Brokaw and Jackson (15, 90), Ashman and Bchler (6), and Kuchta, Lambiris, and
Zabetakis (127). These are not normally used for safety purposes, unless there is some
assurance that the contact time of combustible and air is less than the ignition delay at the
temperature of the hot zone. The minimum autoignition temperature (AIT) is usually the quantity
of interest in safety work, especially when combustible and air can remain in contact for an
indefinite period.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
64
Figure 31Limits of Flammability of Butane-Carbon Dioxide-Air and

Butane-Nitrogen-Air Mixtures at 25C and Atmospheric Pressure.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
65
Figure 32Limits of Flammability of Various n-Pentane-Inert Gas-Air Mixtures at


Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
66
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 33Limits of Flammability of Various n-Hexane-Inert Gas-Air Mixtures at


Not for Resale
67
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 34Limits of Flammability for n-Heptane-Water Vapor-Air Mixtures at 100

and 200C and Atmospheric Pressure.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
68
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 35Approximate Limits of Flammability of Higher Paraffin Hydrocarbons

(CnH2n+2, n5) in Carbon Dioxide-Air and Nitrogen-Air Mixtures at 25C and
Atmospheric Pressure.

Not for Resale
69
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 36Effect of Pressure on Limits of Flammability of Natural Gas-NitrogenAir Mixtures at 26C.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
70
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 37Effect of Pressure on Limits of Flammability of

Ethane-Carbon Dioxide-Air Mixtures at 26C.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
71
Figure 38Effect of Pressure on Limits of Flammability of Ethane-Nitrogen-Air

Mixtures at 26C.

Not for Resale
72

Propane-Carbon Dioxide-Air Mixtures.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
73
ANSI/ISA-TR12.13.01-1999 (R2005)

Propane-Nitrogen-Air Mixtures.
Some AIT values for paraffin hydrocarbons in air obtained by Setchkin in a 1-liter spherical Pyrex
flask (194) and by Zabetakis, Furno, and Jones in a 200 cc Pyrex Erlenmeyer flask (237) are
given in table 4. Interestingly enough, experiments conducted in these and other flasks generally
indicate that flask shape and size are important in determining the AIT. The AIT data obtained in
the 200 cc flask may be correlated with molecular structure by plotting them against the average
carbon chain length defined as
n
2 gi Ni
i
L ave = ------------------------ ,
M(M 1 )
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
(49)
ANSI/ISA-TR12.13.01-1999 (R2005)
74
where gi is the number of possible chains each containing Ni carbon atoms and M is the number
of methyl (CH3) groups. For example, n-nonane and 2,2,3,3-tetramethyl pentane each have
9 carbon atoms, but the former has 2 methyl groups and the latter has 6. The former has only
one chain of 9 carbon atoms with a methyl group on each end, and the latter has a maximum of
4 chains with 3 carbon atoms, 8 chains with 4 carbon atoms, and 3 chains with 5 carbon atoms.
Thus, n-nonane has an average chain length of 9 and 2,2,3,3-tetramethyl pentane has an
average of 3.9. The more highly branched a combustible is, the higher its ignition temperature
will be. Minimum autoignition temperatures of 20 paraffins were plotted as ordinate against the
average chain length as abscissa (fig. 43). The data fall into two regionsa high-temperature
region in which the AIT is greater than 400C and a low temperature region in which the AIT is
less than 300C. These regions coincide with those of Mulcahy who found that oxidation
proceeds by one of two different mechanisms (152), and by Frank, Blackham, and Swarts (60).
The AIT values of combustibles in the first region are normally much more sensitive to the
oxygen concentration of the oxidizing atmosphere and to the spray injection pressure than are
the combustibles in the second region. Unfortunately, the available consistent AIT data about the
effects of oxygen concentration and injection pressure are too meager to permit a detailed
comparison.
The physical processes (206) and reactions that lead to autoignition are of interest in any
detailed study of this ignition process. Salooja (184), Terao (207), Affens, Johnson and Carhart
(1, 2), and others have studied the autoignition of various hydrocarbons in an effort to determine
the mechanisms that lead to the ignition reaction.
An increase in pressure generally decreases the AIT of a combustible in a given oxidant. For
example, the AIT of a natural gas in air decreased from 530C at 1 atmosphere to 240C at 610
atmospheres (9,000 psig) (78). The AIT's of several hydrocarbons were found to obey
Semenov's equation over a limited pressure range (248):
P A
log --- = --- + B
T T
(50)
where T is the AIT at an initial pressure P, and A and B are constants. Accordingly, the AIT
values obtained at atmospheric pressure should not be used to assess ignition hazards at high
pressures.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
75
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 41Effect of Pressure on Minimum Oxygen Requirements for Flame

Propagation Through Natural Gas-Nitrogen-Air, Ethane-Nitrogen-Air, and
Propane-Nitrogen-Air Mixtures at 26C.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
76
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 42Low-Temperature Limit of Flammability of Decane-Air, Dodecane-Air

and Decane-Dodecane-Air Mixtures (Experimental Points 0).
Burning Rate
The burning velocities, Su, of various hydrocarbons have been measured by numerous
investigators in air and other oxidants (68, 131). At one atmosphere and 26 C, the burning
velocities of paraffin hydrocarbons in air range from a few centimeters a second near the limits to
about 45 cm/sec near the stoichiometric mixture composition; much higher values are obtained
with paraffin hydrocarbon-oxygen mixtures. Figure 44 gives results obtained by Gibbs and
Calcote for four paraffin hydrocarbon-air mixtures at atmospheric pressure and room
temperature (68). The data are expressed in terms of the stoichiometric composition, Cst;
burning velocities are given for the composition range from 0.7 to 1.4 Cst. These authors have
presented similar data for combustibles at 25 and 100C. Figure 45 gives results obtained by
Singer, Grumer, and Cook for three paraffin hydrocarbon-oxygen mixtures at atmospheric
pressure and room temperature in the range from 0.3 to 1.4 Cst (198). Burning velocities range
from a low of 125 cm/sec to a high of 425 cm/sec; these values are considerably greater than
those obtained in air. A change in either temperature or pressure will alter Su for a particular
mixture. For example, Agnew and Graiff (3) found that an increase in pressure causes Su of
stoichiometric methane-air and propane-air mixtures to decrease in the pressure range from 0.5
to 20 atmospheres (fig. 46); Su of stoichiometric methane-oxygen mixtures, however, increased
in the pressure range from 0.2 to 2 atmospheres (fig. 47). The effect of temperature is more

Not for Resale
77
ANSI/ISA-TR12.13.01-1999 (R2005)
consistent. For a given pressure and mixture composition, an increase in temperature raises Su.
In general:
Su = A + BTn
(51)
where A and B are constants, T is the temperature and n is a constant for a particular mixture
composition. Dugger, Heimel, and Weast (50, 51, 81) obtained a value of 2.0 for n for some of
the paraffin hydrocarbons (fig. 48). The burning velocity of the stoichiometric methane-air and
methane-oxygen mixtures given in figures 44 and 45 do not agree with the values given in figures
46 to 48 but, in each case, the burning velocity data are internally consistent.
550
CH 4
C 2H 6
500
C3 H 8
C
C-C-C
C-C-C
450
CC
C-C-C-C-C
C
C
CC
C-C-C-C
C
C-C-C-C-C
C
400
C-C-C-C
n- C4 H 10
350
C
C
C-C-C-C-C
300
n- C 5 H 12
n- C9 H 20
250
n- C10 H 22
n- C 8 H 18
n- C6 H 14
n- C12 H 26
n- C16 H 34
n- C14 H 30
n- C7 H 16
200
1
11
13
15
17
Figure 43Minimum Autoignition Temperatures of Paraffin Hydrocarbons in Air

as a Function of Average Carbon Chain Length.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
AVERAGE CARBON CHAIN LENGTH, L avg
ANSI/ISA-TR12.13.01-1999 (R2005)
78
The actual flame speed relative to a fixed observer may be much greater than Su since the
burned gases, if not vented, will expand and impart a motion to the flame zone. If detonation
occurs, the reaction speed increases markedly. For example, figure 49 gives the Kogarko data
on velocities with which a detonation wave propagates through various methane-air mixtures at
atmospheric pressure in a 30.5 cm-diameter (125). Similar results have been obtained by
Gerstein, Carlson, and Hill at low pressures with natural gas-air mixtures (67).
In each case, powerful initiators were required to obtain a detonation in relatively large pipes.
The energy requirements for ignition are reduced if oxygen is used as the oxidant in place of air.
Further, the detonation velocity increases as the oxygen content of the atmosphere is increased.
Detonation velocities obtained by Morrison for methane, ethane, propane, butane, and hexane in
oxygen are given in figure 50 (150); similar data obtained by Wayman and Potter are given in
figure 51 for n-heptane-nitrogen-white fuming nitric acid vapors (219). Of principal interest here
is the magnitude of the detonation velocity; even in air, this velocity is so great that pressure
waves are not sent out ahead of the detonation front. Thus, pressure detectors that are useful in
explosion prevention with deflagration waves are useless with detonations.
With liquid fuels, the burning rate depends in part on the rate of vaporization and on the pool size.
Burgess, Strasser, and Grumer (20) have shown that the liquid regression rate v is given by
v = v ( 1 e
Kd
),
(52)
where v is the value of v in large pools, K is a constant, and d is the pool diameter. They
expressed v as:
net heat of combustion, DH c

v = 0.0076 ---------------------------------------------------------------------------------- cm/min.
sensible heat of vaporization, DH r
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
(53)
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
79
Figure 44Burning Velocities of Methane-, Ethane-, Propane-, and n-Heptane

Vapor-Air Mixtures at Atmospheric Pressure and Room Temperature.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
80
Figure 45Burning Velocities of Methane-, Ethane-, and Propane-Oxygen,

Mixtures at Atmospheric Pressure and Room Temperature.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
81
Figure 46Variation in Burning Velocity of Stoichiometric Methane-Air and

Propane-Air Mixtures With Pressure at 26C.
Figure 52 gives a summary of the v values for a number of combustibles, including several
paraffin hydrocarbons (21). Of special significance here is that DHc/DH is nearly constant (about
100) for the paraffin hydrocarbons, so that their linear burning rates in large pools are all about
3/4 cm per minute.
UNSATURATED HYDROCARBONS (CnH2n, CnH2n2)
Limits in Air
The molecular weight, specific gravity, and other properties of the hydrocarbons considered here
are included in table 7. At room temperature and atmospheric pressure, the lower limits of
flammability of the olefins (CnH2n) excluding ethylene fall in the range from 46 to 48 mg
combustible vapor per liter of air (0.046 to 0.048 oz combustible vapor per cubic foot of air).
The effect of temperature on the lower limit of flammability of ethylene in air at atmospheric
pressure, assuming a constant limit flame temperature, is shown by the curve labeled "Upward
propagation of flame" in figure 53. Unfortunately, only downward flame propagation data are

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
82
available over an extended temperature range (222); these are included in figure 53. As in the
case of similar data obtained with methane, these define a straight line parallel to the "Constant
flame temperature," "Upward propagation of flame" line. Again, the modified Burgess-Wheeler
law, equation (33), gives a variation in lower limit with temperature that is close to that given by
the "Constant flame temperature" line, so that either could be used at temperatures below the
AIT of ethylene (490C). Moreover, as the limit flame temperatures of olefins are not too different
from those of paraffin hydrocarbons, the generalized graph for Lt /L25 (fig. 23) can be used for
these unsaturated hydrocarbons.
Table 7 Properties of unsaturated hydrocarbons

Lower limit in air
Combustible
Formula
Sp gr
(Air=1)
Cst in air
(vol pct)
Net
DHc
Kcal
---------- mole-
L25
(vol pct)
Upper limit in air

Ref.
mg
L -------
1
L
25
--------C
st
U25
(vol pct)
Ref.
mg
U -------
1
U
25
---------C
st
Ethylene
C2H4
28.05
0.97
6.53
316.2
2.7
0.41
35
(115)
36
5.5
700
(26)
Propylene
C3H6
42.08
1.45
4.45
460.4
2.4
.54
46
(101)
11
2.5
210
(40)
Butene-1
C4H8
56.10
1.94
3.37
607.7
1.7
.50
44
(1)
9.7
2.9
270
(1)
cis-Butene-2
C4H8
56.10
1.94
3.37
606.0
1.8
.53
46
(40)
9.7
2.9
270
(40)
Isobutylene
C4H8
56.10
1.94
3.37
604.1
1.8
.53
46
(40)
9.6
2.8
260
(26)
3-Methyl-butene-1
C5H10
70.13
2.42
2.72
752.3
1.5
.55
48
(40)
9.1
3.3
310
(40)
Propadiene
C3H4
40.06
1.38
4.97
443.7
2.6
.53
48
(2)
1,3-Butadiene
C4H6
54.09
1.87
3.67
576.3
2.0
.54
49
(102)
12
3.3
320
(26)
1 Figures
compiled at Explosive Res. Center, Federal Bureau of Mines.

Calculated value.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
83
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 47Variation in Burning Velocity of Stoichiometric Methane- and EthyleneOxygen Mixtures With Pressure at 26C.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
84
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 48Effect of Temperature on Burning Velocities of Four Paraffin

Hydrocarbons in Air at Atmospheric Pressure.

Not for Resale
85
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 49Detonation Velocities of Methane-Air Mixtures at Atmospheric

Pressure. (Initiator: 50-70 grams of amatol explosive. Pipe diameter: 30.5 cm.)

Not for Resale
86
Figure 50Detonation Velocities of Methane-, Ethane-, Propane-, Butane-, and

Hexane-Oxygen Mixtures at Atmospheric Pressure.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
87
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 51Detonation Velocities of n-Heptane Vapor in WFNA (White Fuming

Nitric Acid)-Nitrogen Gas Mixtures at Atmospheric Pressure and 400K.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
88
Figure 52Relation Between Liquid-Burning Rate (Large-Pool Diameter) and Ratio

of Net Heat of Combustion to Sensible Heat of Vaporization.

The limits of flammability of ethylene, propylene, isobutylene, butene-1, 3 methyl butene-1, and
butadiene in various inert-air atmospheres have been determined by Jones and coworkers (100,
101, 103), (figs. 54-60). The first two figures are modifications of the limit-of-flammability
diagrams given in (40); the third is essentially the same as that given in the earlier publication but
includes the experimental points. The other curves were constructed from original, unpublished
data obtained at the Explosives Res. Center, Federal Bureau of Mines.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
89
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 53Effect of Temperature on Lower Limit of Flammability of Ethylene in Air


Not for Resale
90
ETHYLENE, volume-percent
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 54Limits of Flammability of Ethylene-Carbon Dioxide-Air and EthyleneNitrogen-Air Mixtures at Atmospheric Pressure and 26C.
Other limit-of-flammability determinations have been made in oxygen and nitrous oxide. These
data are included in table 8 (40, 100, 106).
Autoignition
There have been few determinations of AIT's of the unsaturated hydrocarbons in air or other
oxidants; the available data (94, 116, 191) are summarized in table 9.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
91
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 55Limits of Flammability of Propylene-Carbon Dioxide-Air and

Propylene-Nitrogen-Air Mixtures at Atmospheric Pressure and 26C.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
92
Burning Rate
The burning velocity of ethylene has been determined in air, oxygen, and oxygen-nitrogen
atmospheres by numerous investigators (3, 47, 49, 68, 131). In general, it is higher than the
velocities of the paraffin hydrocarbons under the same conditions (fig. 47). Similar results are to
be expected for other unsaturated hydrocarbons, although the available data are rather meager.
Stability
Many unsaturated hydrocarbon vapors can propagate flame in the absence of air at elevated
temperatures and pressures; that is, they have no upper limit of flammability. These
combustibles have positive heats of formation, DHf (table 10) and would therefore liberate heat if
decomposed to the elements carbon and hydrogen. Even more heat would be liberated if gases
with a negative heat of formationfor example, methaneform from the elements. In practice, a
mixture of products results upon decomposition of such combustibles. For example, a
propagating decomposition reaction can be initiated in pure ethylene in a 2-inch-ID tube at 23C
and pressures as low as 750 psig, using 2 grams of guncotton. A reaction can be initiated at
21C and pressures as low as 975 psig with 1 gram of guncotton. The decomposition products
are primarily carbon, methane, and hydrogen; approximately 30 Kcal are released per mole of
ethylene decomposed. Propylene yielded similar products following explosive decomposition
during compression to 4,860 atmospheres (34).
Propadiene and butadiene also decompose readily under the action of powerful ignitors.
Propadiene vapor has been decomposed in a 2-inch tube at 120C and 50 psig using a platinum
wire ignitor. Decomposition of butadiene in an industrial accident resulted in a "popcorn"
polymer; the reaction was apparently initiated by an unstable peroxide (4).
ACETYLENIC HYDROCARBONS (CnH2n2)
Limits in Air
--`,,```,,,,````-`-`,,`,,`,`,,`---
Acetylene forms flammable mixtures in air at atmospheric pressure and 25C, in a range from 2.5
to 100 volume-percent acetylene. Quenched and apparatus limited upper limits have been
obtained in 1- , and 2-, and 3-inch diameter tubes (40), but pure acetylene can propagate flame
at atmospheric pressure in tubes with diameters of at least 5 inches. Sargent has summarized
available data on initial pressure requirements for deflagration and detonation through acetylene
in horizontal tubes of about .02 to 6 inches ID at 60F. (89, 185). His curves are given in figure
61, which also includes an experimental point from the data of Jones and coworkers obtained in
a vertical 2-inch-diameter tube. The existence of this point, at a pressure below that given by
Sargent's curve for a 2-inch tube, indicates that this curve should be used only for horizontal
systems. The point labeled "Industrial explosion" was reported by Miller and Penny (144) and
presumably refers to a deflagration. The third experimental point is discussed, along with the
detonation curve, in the section on stability.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
93
Figure 56Limits of Flammability of Isobutylene-Carbon Dioxide-Air and

Isobutylene-Nitrogen-Air Mixtures at Atmospheric Pressure and 26C.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
94
Table 8 Limits of flammability of unsaturated hydrocarbons at atmospheric

pressure and room temperature, in volume-percent combustible vapor
(L=lower limit; U=upper limit)
In air
In nitrous
oxide
In oxygen
Combustible
L
Ethylene
2.7
36
2.9
80
1.9
40
Propylene
2.0
11
2.1
53
1.4
29
Butene-1
1.6
10
1.7
58
Butene-2
1.7
1.7
55
--`,,```,,,,````-`-`,,`,,`,`,,`---
9.7

Not for Resale
95
ANSI/ISA-TR12.13.01-1999 (R2005)
Table 9 Minimum autoignition temperatures of unsaturated hydrocarbons at

atmospheric pressure
Autoignition Temperature
In air
In oxygen
Combustible
C
Ref.
Ref.
Ethylene
490
914
(116)
485
905
(116)
Propylene
458
856
(94)
423
793
(1)
Butene-1
384
723
(1)
310
590
(1)
Butene-2
324
615
(1)
1,3-Butadiene
418
784
(191)
335
635
(191)
compiled by Explosives Res. Center, Federal Bureau of Mines.

--`,,```,,,,````-`-`,,`,,`,`,,`---
(1)Figures
Table 10 Heats of formation (Kcal/mole) of unsaturated hydrocarbons at 25C.

Combustible:
DHf1
Acetylene
54.2
Propadiene
45. 9
Methylacetylene
44.3
1-3, Butadiene
26.8
Ethylene
12.5

Propylene
4.9
1-Butene
.3
Refs. (124,183).
Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
96
Figure 57Limits of Flammability of Isobutylene-Water Vapor-Oxygen Mixtures at

--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
97
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 58Limits of Flammability of Butene-1-Carbon Dioxide-Air and

Butene-1-Nitrogen-Air Mixtures at Atmospheric Pressure and 26C.
The effect of temperature on the lower limit of flammability was determined by White in a 2.5-cm
tube with downward propagation of flame (222). Although the actual limit values are not
satisfactory for our purposes, they can be used to check the applicability of the Lt/L25 ratio data
presented in figure 23. The White ratio of lower limits at 300 and 20C. is 2.19/2.90=0.76; the
corresponding ratio from "Constant flame temperature" curve in figure 23 is 0.78. Accordingly,
this figure should be satisfactory for use with acetylene at temperatures in the range from 20 to
300C.
The lower limit of flammability of methylacetylene (propyne) in air at atmospheric pressure is 1.7
volume-percent, equal to 0.34 Cst which compares favorably with the value for acetylene
(0.32 Cst). Upper limit investigations have been conducted by Fitzgerald (59) in a 2-inch tube at
20 and 120C to determine the low-pressure limits or lowest pressures at which a flame will
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
98
propagate through methylacetylene vapor at these temperatures. He found these to be 50 and

30 psig at 20 and 120C, respectively. In a 4-inch tube, Hall and Straker (77) obtained a lowpressure limit of 43 psig at 20C. This indicates that the upper limit of flammability of
methylacetylene in air is probably less than 100 percent at 20C and 1 atmosphere.
--`,,```,,,,````-`-`,,`,,`,`,,`---
The quantities of propylene required to prevent flame propagation through methyl-acetylenepropadiene-propylene mixtures at 120C and 50 and 100 psig have been determined in
1-, 2-, 4-, and 12-inch tubes (fig. 62), and at 120C and 100 psig in a 24-inch sphere. As noted,
the propylene requirements are strongly affected by temperature, pressure, and container size.
As the tube diameter increases, the quantity of propylene required to prevent flame propagation
increases; this effect is less pronounced in the larger vessels (diameter greater than 4 inches)
than in the smaller vessels (diameter less than 4 inches). The results obtained in the 24-inch
sphere were similar to those in the 12-inch tube.
Figure 59: Limits of Flammability of 3 Methyl Butene-1-Carbon Dioxide-Air and

3 Methyl-Butene-1-Nitrogen-Air Mixtures at Atmospheric Pressure and 26C.

Not for Resale
99
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 60Limits of Flammability of Butadiene-Carbon Dioxide-Air and ButadieneNitrogen-Air Mixtures at Atmospheric Pressure and 26C.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
100
Figure 61Effect of Tube Diameter on Initial Pressure Requirements for

Propagation of Deflagration and Detonation Through Acetylene Gas.
--`,,```,,,,````-`-`,,`,,`,`,,`---
Gliwitzky (71), and Jones and coworkers determined the effects of carbon dioxide and nitrogen
on the limits of acetylene in air at atmospheric pressure and room temperature. Unfortunately, all
measurements were made in tubes that were too narrow to give actual upper limit data.
Nevertheless, the resulting quenched-limit data are summarized in figure 63, because they show
the relative effects of adding two inert diluents to acetylene-air mixtures in a 2-inch-ID tube.
Autoignition
A summary of available autoignition temperature data for acetylene, acetylene-air, and
acetylene-oxygen mixtures in clean systems is given in figure 64. They are based on
measurements by Jones and Miller (110), by Jones and Kennedy in quartz tubes (99), and by
Miller and Penny in a 0.5-inch steel pipe, 15 inches long (144). Jones and Miller found minimum
autoignition temperatures of 305 and 296C for a variety of acetylene-air and acetylene-oxygen
mixtures, respectively, at atmospheric pressure. Miller and Penny report little variation in the
autoignition temperature of acetylene in a clean pipe at 4 to 26 atmospheres initial pressure.

Not for Resale
101
ANSI/ISA-TR12.13.01-1999 (R2005)
However, the presence of 1 gram of powdered rust, scale, kieselguhr, alumina, silica gel, or
charcoal lowered the pipe temperature required for ignition to a 280 to 300C range. The
presence of 1 gram of potassium hydroxide lowered the pipe temperature still further to 170C.
The impact of a 0.25-inch steel ball falling from a height of 15 inches against a fragment of
copper acetylide produced a hot spot that ignited the surrounding gaseous acetylene at room
temperature and 3 atmospheres.
Burning Rate
--`,,```,,,,````-`-`,,`,,`,`,,`---
The burning velocity data for acetylene in air obtained by Manton and Milliken at 1 atmosphere
and room temperature are given in figure 65 (138). The burning velocity ranges from a low of a
few centimeters per second near the lower limit to a high of about 160 cm/sec on the rich side of
the stoichiometric composition. Parker and Wolfhard (164) have found considerable variation in
the burning velocity of acetylene in various oxidants. The burning velocities in stoichiometric
mixtures with oxygen, nitrous oxide, nitric oxide, and nitrogen tetroxide were found to be 900,
160, 87, and 135 cm/sec, respectively; for comparison, the burning velocity in a stoichiometric
acetylene-air mixture (fig. 65) is 130 cm/sec.

Not for Resale
102
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 62Range of Flammable Mixtures for Methylacetylene-PropadienePropylene System at 120C and at 50 and 100 Psig.
The burning velocities of acetylene-air mixtures were found to be independent of pressure
between 0.1 and 1.0 atmosphere (138). Similarly, Agnew and Graiff (3) and Parker and Wolfhard
(164) found the burning velocities of stoichiometric acetylene-oxygen and acetylene-nitrous
oxide mixtures were independent of pressure between approximately 0.5 and 2 atmospheres
and 0.03 and 1 atmosphere, respectively. The burning velocities of stoichiometric acetylenenitric oxide and acetylene-nitrogen tetroxide mixtures increased slightly over this pressure range
0.03 to 1 atmosphere (164).

Not for Resale
103
ANSI/ISA-TR12.13.01-1999 (R2005)
Stability
As noted, acetylene can propagate flame in the absence of air (39, 165). The pressures required
for propagation at subsonic (deflagration) and supersonic rates (detonation) into the unburned
gas are given for a range of pipe diameters in figure 61 (185). Deflagration is discussed briefly
under Limits of Flammability; detonation is discussed in this section.
--`,,```,,,,````-`-`,,`,,`,`,,`---
The curve labeled "Detonation" in figure 61 gives the minimum pressure required for propagation
of a detonation, once initiated, in tubes of 0.3 to 10 inches diameter. In practice, a detonation
may be initiated directly from a deflagration that has propagated through a rather ill-defined
distance, known as the predetonation or run-up distance. This distance depends on
temperature, pressure, tube diameter, condition of tube walls, and on ignition-source strength.
For example, using a fused platinum wire ignitor, Miller and Penny (144) found the predetonation
distance for acetylene in a 1-inch tube to be 30 feet at 51.4 psia, 22 feet at 55.9 psia, 12 feet at
73.5 psia, and 2.8 to 3.2 feet at 294 psia initial pressure. Extrapolation of these data yields the
point in figure 61 for a very large predetonation distance. This point (44 psia and 1-inch diameter)
lies fairly close to the detonation curve established by Sargent (185). The maximum length-todiameter ratios (L/D) given by Sargent for establishing detonation in acetylene is plotted against
initial pressure in figure 66. In tubes, having a diameter greater than those given along the top of
the figure and having powerful ignitors, the L/D ratio will be less than that given by the curve.
Nevertheless, this figure should be of use in giving the outer bound of L/D and the approximate
quenching diameter; a better value for the quenching diameter can be obtained directly from
figure 61.
Although predetonation distances are difficult to measure and experimental data often exhibit
much scatter, they are of interest in safety work because they can be used to evaluate the
maximum pressures likely to occur in a system due to cascading or pressure piling. This
phenomenon presents a special problem because the final pressure achieved in a detonation
depends on the initial pressure at the onset of detonation. For example, the maximum pressure
to be expected from the deflagration of acetylene at moderate pressures is about 11 times the
initial pressure (144); the maximum to be expected from a detonation is about 50 times the initial
pressure. As the pressure equalizes at the speed of sound in a deflagration, the maximum initial
pressure to be expected upon transition from deflagration to a detonation is approximately 11
times the fraction of acetylene that has been burned times the initial precombustion pressure.
Fifty times this pressure is the approximate maximum pressure that would be obtained when a
detonation occurs. To illustrate this, Sargent has plotted the final-to-initial pressure ratio (Pf /Pi )
against the predetonation distance-to-tube length for acetylene. A similar graph is given in figure
67. To use this graph, the maximum predetonation distance to be expected must first be
determined from figure 66. This distance divided by the tube length gives the maximum final-toinitial pressure ratio.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
104
Figure 63Quenched Limits of Flammability of Acetylene-Carbon Dioxide-Air and

Acetylene-Nitrogen-Air Mixtures at Atmospheric Pressure and 26C,
Obtained in a 2-Inch Tube.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
105
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 64Minimum Autoignition Temperatures of Acetylene-Air and AcetyleneOxygen Mixtures at Atmospheric and Elevated Pressures.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
106
Figure 65Burning Velocity of Acetylene-Air Mixtures at Atmospheric Pressure

and Room Temperature.
Limits in Air
The combustibles considered in this section are listed in table 11, with pertinent properties. At
atmospheric pressure and room temperature, the lower limits of flammability of the aromatic
hydrocarbons are approximately 502 mg/l (0.0500.002 oz combustible vapor per cubic foot of
air).
The lower limit of toluene was determined by Zabetakis and coworkers in air at 30, 100, and
200C (235, 247); the variation in lower limit with temperature is given by equations (31) and (33)
derived for paraffin hydrocarbons, and the corresponding curves of figure 23. For example,
L200C/L30C was found to be 1.07/1.24 or 0.86; the ratio predicted by the curve in figure 23 is
0.87.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
AROMATIC HYDROCARBONS (CnH2n6)
107
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 66Maximum L/D Ratio Required for Transition of a Deflagration to a

Detonation in Acetylene Vapor at 60F and from 10 to 70 Psia.
Table 11 Properties of selected aromatic hydrocarbons
Lower limit in air1
Combustible
Formula
Benzene
Sp gr
(Air=1)
Cst in air
(vol pct)
Net
DHc
Kcal
-----------mole
L100
(vol pct)
L
100
-----------C
st
Upper limit in air1
mg
L -------
1
U100
(vol pct)
U
100
------------C
st
mg
U -------
1
C6H6
78.11
2.69
2.72
757.5
1.3
.48
47
7.9
2.9
300
Toluene
C7H8
92.13
3.18
2.27
901.5
1.2
.53
50
7.1
3.1
310
Ethyl benzene
C8H10
106.16
3.67
1.96
1048.5
1.0
.51
48
6.7
3.4
340
o-Xylene
C8H10
106.16
3.67
1.96
1045.9
1.1
.56
53
6.4
3.3
320
m-Xylene
C8H10
106.16
3.67
1.96
1045.5
1.1
.56
53
6.4
3.3
320
p-Xylene
C8H10
106.16
3.67
1.96
1045.7
1.1
.56
53
6.6
3.4
340
Cumene
C9H12
120.19
4.15
1.72
1194.2
.88
.51
48
6.5
3.8
370
p-Cymene
C10H14
134.21
4.63
1.53
1341.8
.85
.56
51
6.5
3.6
350
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
108
Ref. (247)
Figure 67Final-to-Initial Pressure Ratios Developed by Acetylene With

Detonation Initiation at Various Points Along a Tube.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
109
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
The upper limits of the aromatics considered here at 100C are included in table 11 (247). These
were obtained at atmospheric pressure in a 2-inch-diameter tube, open at one end. Butler and
Webb obtained upper limit data on a commercial grade cumene (93.3 pct cumene) in air at
elevated temperatures and atmospheric and elevated pressures in a closed bomb (31). Their
values range from 8.8 percent cumene (80C and atmospheric pressure) to 10.8 percent cumene
(146C and 100 psig pressure).

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
110

The limits of flammability obtained by Burgoyne (29) and by Jones (40) for benzene-carbon
dioxide-air and benzene-nitrogen-air mixtures at atmospheric pressure and 25 C are given in
figure 68; similar data are given for the last two mixtures at atmospheric pressure and 150C.
The inerting requirements at 25C are approximately the same as those of n-hexane (fig. 33).
Again, it should be noted that the methyl bromide data are not consistent with those obtained by
Hill (compare figs. 28 and 33). These latter data (84) were used to construct the approximate
(broken) flammability curves for the benzene-methyl bromide-air system.
Figure 68Limits of Flammability of Benzene-Methyl Bromide-Air Mixtures at 25C

and Benzene-Carbon Dioxide-Air and Benzene-Nitrogen-Air Mixtures at 25and
The decrease in the minimum oxygen requirements for flame propagation (from 14.20.3
volume-percent at 25C to 13.10.3 volume percent at 150 in a carbon dioxide-air atmosphere;
from 11.40.3 volume-percent at 25C to 10.10.3 volume-percent at 150 in a nitrogen-air
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
111
ANSI/ISA-TR12.13.01-1999 (R2005)
atmosphere) is within the range predicted by the modified Burgess-Wheeler law (equation (35),
fig. 23).
The limits of flammability of orthoxylene (C6H4(CH3)2)-water-hydrogen peroxide mixtures were
determined at 154C and 1 atmosphere pressure by Martindill, Lang, and Zabetakis (140). The
data are presented in a triangular plot in figure 69; compositions are expressed in mole-percent
as in the original presentation. This system has no lower limit mixtures, as a flame can be
initiated in hydrogen peroxide vapors (186). As a 90-weight-percent hydrogen peroxide was
actually used to obtain these flammability data, all compositions were calculated to yield values
based on a 100-percent hydrogen peroxide content. This could be done here because only three
components are considered. Where four components are considered, the flammability data can
be presented in a three-dimensional plot; if two of the components appear in fixed proportions, a
triangular plot can be used with the two components (for example, 90-weight-percent hydrogen
peroxide) considered as a single component. Such a plot is presented in figure 70 for 90-weightpercent hydrogen peroxide-orthoxylene-formic acid (HCOOH) at 154C and 1 atmosphere. This
was considered to be a plane in a regular tetrahedron in the original article and is therefore not a
regular triangle. As before, only an upper limit curve is given because 90-weight-percent
hydrogen peroxide is flammable. In addition, a calculated curve based on Le Chatelier's rule is
given, as is the upper limit curve obtained with decomposed hydrogen peroxide. Decomposition
of the peroxide lowers the upper limit appreciably and yields a system which has a lower limit of
flammability (not determined in this study).
Autoignition
The minimum autoignition temperatures of a series of aromatic hydrocarbons in air at
atmospheric pressure are given in figure 71 as a function of the correlation parameter Lave. This
parameter was determined by use of equation (49), treating the benzene ring as a CH3 group
(241). When the benzene ring contains two side groups, Lave is determined first for the side
group that yields the largest average value and to this is added 1/2, 1/3, or 1/4 of the average
chain length of the second side group; (1/2, 1/3, and 1/4 correspond to the ortho-, meta-, and
para-positions, respectively). The data again fall into high- and low-temperature regions (fig. 43).
Burning Rate
Burning rates and detonation velocities of benzene in air and oxygen appear to be approximately
the same as those of the higher paraffin hydrocarbons. For example, the results of Golovina and
Fyodorov (211) show that the maximum burning velocities of benzene in nitrogen-oxygen
mixtures range from about 295 cm/sec in oxygen to 45 cm/sec in air; the maximum burning
velocities of hexane in various nitrogen-oxygen mixtures range from about 260 cm/sec in oxygen
to 40 cm/sec in air. Similarly, Fraser (61) found the maximum detonation velocities of benzene
and n-octane in oxygen to be 2,510 and 2,540 m/sec, respectively.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
112
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 69Limits of Flammability of H2O2-C6H4(CH3)2-H2O at 154C and

1 Atmosphere Pressure.

Not for Resale
113
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 70Limits of Flammability of 90-Weight-Percent H2O2-C6H4(CH3)2-HCOOH

at 154C and 1 Atmosphere Pressure.
ALICYCLIC HYDROCARBONS (CnH2n)
Limits in Air
A summary of the pertinent properties of some of the members of the series is given in table 12.
The lower limits of flammability in air at atmospheric pressure and room temperature fall in the
range from 483mg/l (.048.003 oz combustible per cubic foot of air). By volume, this is
equivalent to approximately 0.55 Cst, which is the same as for paraffin hydrocarbons. The ratio
of the upper limit to Cst appears to increase with molecular weight.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
114
According to Jones (40), the lower limit of cyclohexane in air at atmospheric pressure and 26C
determined in a 2.0-inch tube is 1.26 volume-percent. Under the same conditions, Burgoyne and
Neale (26) found the lower limit to be 1.34 volume-percent, using a 2.5-inch tube. Matson and
Dufour (141) found the lower limit to be 1.12 volume-percent at 21C in a 12-inch diameter
chamber about 15 inches long; however, there is evidence that they did not use the same criteria
of flammability as did the other authors; only one observation window was provided at the top of
a rather squatty chamber, whereas with the glass tubes used by Jones and by Burgoyne and
Neale the flame could be observed along the entire tube. Accordingly, the data of Jones and of
Burgoyne and Neale are used here.
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 71Minimum Autoignition Temperatures of Aromatic Hydrocarbons in Air

as a Function of Correlation Parameter Lave.

Not for Resale
115
ANSI/ISA-TR12.13.01-1999 (R2005)
Table 12 Properties of selected alicyclic hydrocarbons

Lower limit in air
Combustible
Cyclopropane
Formula
C3H6
42.08
Net
DHc
Sp gr
(Air=1)
Cst in
air
(vol pct)
1.45
4.45
465
1
Cyclobutane
C4H8
56.10
1.94
3.37
Cyclopentane
C5H10
70.13
2.42
2.72
Cyclohexane
C6H12
84.16
2.91
2.27
Ethylcyclobutane
C6H12
84.16
2.91
2.27
Cycloheptane
C7H14
98.18
3.39
1.96
Methylchcylhexane
C7H14
98.18
3.39
1.96
Kcal
-----------mole
L25
(vol
pct)
2.4
L
25
--------C
st
.54
mg
L -------
1
Upper limit in air
Ref.
U25
(vol
pct)
mg
U -------
1
46
(107)
10.4
2.3
220
Ref.
(107)
600
1.8
.56
46
(1)
740.8
1.5
.55
48
(1)
881.7
1.3
.57
49
(40)
7.8
3.4
320
(40)
880
1.2
.53
46
(40)
7.7
3.4
310
(40)
6.7
3.4
310
(1)
1
1
1024
1026.0
1.1
.56
49
(1)
1.1
.56
49
(40)
6.7
3.4
310
(1)
3.4
310
(40)
3.9
350
(40)
Ethylcyclopentane
C7H14
98.18
3.39
1.96
1032.6
1.1
.56
49
(40)
Ethylcylcohexane
C8H16
112.21
1.71
1.71
1173.7
.56
48
(40)
.95
Calculated Value.
P=0.5 atm.
3 t=130 C.
2
--`,,```,,,,````-`-`,,`,,`,`,,`---

U
25
---------C
st
Not for Resale
6.7
6.6
ANSI/ISA-TR12.13.01-1999 (R2005)
116
Figure 72Limits of Flammability of Cyclopropane-Carbon Dioxide-Air,

Cyclopropane-Nitrogen-Air, and Cyclopropane Helium-Air Mixtures at 25C and
The limits of flammability of cyclopropane-carbon dioxide-air, cyclopropane-nitrogen-air, and
cyclopropane-helium-air mixtures at 25C and atmospheric pressure are given in figure 72 (106).
The first two curves are similar to those obtained with paraffin hydrocarbons (fig. 35).
The limits of flammability of cyclopropane-helium-oxygen and cyclopropane-nitrous oxide-oxygen
mixtures at 25C and atmospheric pressure are given in figure 73 (106). The latter curve differs
from the former, as both additives are oxidants (oxygen and nitrous oxide).
The limits of flammability of cyclopropane-helium-nitrous oxide mixtures at 25C and atmospheric
pressure are given in figure 74 (106). Here the minimum oxidant concentration (nitrous oxide)
required for flame propagation is approximately twice the corresponding concentration of oxygen
in the systems cyclopropane-helium-air (fig. 72) and cyclopropane-helium-oxygen (fig. 73).
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
117
ANSI/ISA-TR12.13.01-1999 (R2005)
ALCOHOLS (CnH2n+1OH)
Limits in Air
The alcohols considered here are listed in table 13 together with L25 and U25. The ratios
L25/Cst are approximately 0.5. However, the L (mg/l) values decrease with increase in molecular
weight. If L* is taken to be the weight of combustible material (exclusive of the oxygen in the
molecule) per liter of air, then for the simple alcohols:
(54)
This equation gives the values listed in parentheses in the mg/l column; these are in fair
agreement with the values obtained for the saturated hydrocarbons. Approximate L (mg/l) values
can be obtained from the higher hydrocarbon values given in figure 22 by multiplying these by
the ratio M/(M16). Further, figure 19 can be used to obtain L* and L values in volume-percent.
For example, at 25C, L* is about 47 mg/l from figure 22; the corresponding L*25 from figure19 for
ethyl alcohol (M=46) is 2.2 volume-percent. Then, from equation (54), L is 3.4 volume-percent;
the measured value is 3.3 volume-percent.
The lower limits of methyl alcohol have been determined by Scott and coworkers at 25, 100,
and 200C (192). The values at these three temperatures are 6.7, 6.5, and 5.9 volume-percent,
respectively. The calculated values obtained from the modified Burgess-Wheeler law (fig. 23) at
100 and 200C are 6.4 and 5.8 volume-percent, respectively.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
M 16
L * = L ----------------- .
M
118
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 73Limits of Flammability of Cyclopropane-Helium-Oxygen and

Cyclopropane-Nitrous Oxide-Oxygen Mixtures at 25C and Atmospheric Pressure.

Not for Resale
119
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 74Limits of Flammability of Cyclopropane-Helium-Nitrous Oxide Mixtures

at 25C and Atmospheric Pressure.

The limits of flammability of methyl alcohol-carbon dioxide-air and methyl alcohol-nitrogen-air
mixtures at atmospheric pressure and 25 and 50C are given in figure 75; flammability
determinations on mixtures containing more than 15 percent methyl alcohol vapor were
conducted at 50C. The maximum amounts of carbon dioxide and nitrogen required to prevent
flame propagation in these mixtures were compared with the corresponding maxima for paraffin
hydrocarbons (figs. 28-35); it was found that appreciably more inert is required to make mixtures
containing methyl alcohol nonflammable. Conversely methyl alcohol requires less oxygen to
form flammable mixtures, at a given temperature and pressure, than paraffin hydrocarbons do.
This may be due in part to the oxygen of the alcohol molecule. For the simple alcohols, we have:
C n H 2n + 1 OH + 1.5nO 2 nCO 2 + ( n + 1 )H 2 O .
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
(55)
ANSI/ISA-TR12.13.01-1999 (R2005)
120
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 75Limits of Flammability of Methyl Alcohol-Carbon Dioxide-Air and

Methyl Alcohol-Nitrogen-Air Mixtures at 25C and Atmospheric Pressure.
(Broken Curve at 50C and Atmospheric Pressure.)

Not for Resale
121
ANSI/ISA-TR12.13.01-1999 (R2005)
Table 13 Properties of selected simple alcohols.

Lower limit in air
Sp gr
(Air=1)
Cst in air
(vol pct)
Net DHc
Combustible
Formula
Methyl alcohol
CH3OH
32.04
1.11
12.25
159
6.7
.55
Ethyl alcohol
C2H5OH
46.07
1.59
6.53
306
3.3
.50
n-Propyl alcohol
C3H7OH
60.09
2.07
4.45
448
2.2
.49
n-Butyl alcohol
C4H9OH
74.12
2.56
3.37
596
pri-n- Amyl alcohol
C5H11OH
88.15
3.04
2.72
742
n-Hexyl alcohol
C6H13OH
102.17
3.53
2.27
Kcal
( ----------mole )
888
L25
(vol pct)
1.7
L
25
--------C
st
.50
1.4
.51
1.2
.53
mg
L -------
1
Upper limit in air
Ref.
U25
(vol pct)
U
25
---------C
st
mg
U -------
1
Ref.
103
1
52
(40)
70
46
(40)
60
44
(40)
57
45
(5)
(5)
56
46
(5)
10
55
46
(4)
36
19
14
12
2.9
2.9
3.2
810
405
(225)
480
310
(226)
420
310
(40)
*
M 16
L = L ----------------- .
M
t=60.
3At saturation temperature.
4
t=100 C.
5
Figures compiled by Explosives Res. Center, Federal Bureau of Mines.
6Calculated value.
1
2
Thus, the ratio of oxygen required for complete combustion of an alcohol to that for complete
combustion of the corresponding paraffin, equation (22), is:
3n
R O2 = --------------- .
3n + 1
(56)
When n=1,this ratio is 0.75. The corresponding ratios of the experimental minimum oxygen
values from figures 75 and 28 are 0.82 with carbon dioxide and 0.85 with nitrogen as inert.
The limits of flammability of methyl alcohol-water vapor-air were obtained by Scott (192) in a
2-inch-ID cylindrical tube at 100 and 200C and in a 4.9-liter cylindrical bomb at 400C and
1 atmosphere (fig. 76). Similar data were obtained by Dvorak and Reiser in a 2.2-liter apparatus
at 100C (53).
The limits of flammability of ethyl alcohol-carbon dioxide-air and ethyl alcohol-nitrogen-air
mixtures were obtained at 25C and atmospheric, or one-half atmosphere, pressure as noted
(fig. 77). Additional flammability data obtained for ethyl alcohol at 100C and 1 atmosphere are
given in figure 78. Flammability data for the systems tert-butyl alcohol-carbon dioxide-oxygen
and 2-ethylbutanol-nitrogen-oxygen are given in figures 79-81.
The minimum autoignition temperatures in air and oxygen of a number of alcohols at

atmospheric pressure are given in appendix A. Comparison of these values with those of the
corresponding paraffins (methyl alcohol and methane; ethyl alcohol and ethane, etc.), shows that
the AIT values of the alcohols are generally lower.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
Autoignition
122
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 76Limits of Flammability of Methyl Alcohol-Water Vapor-Air Mixtures at

100, 200, and 400C and Atmospheric Pressure.

Not for Resale
123
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 77Limits of Flammability of Ethyl Alcohol-Carbon Dioxide-Air and Ethyl

Alcohol-Nitrogen-Air Mixtures at 25C and Atmospheric Pressure.
(Broken curves at one-half atmosphere.)
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
124
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 78Limits of Flammability of Ethyl Alcohol-Water Vapor-Air Mixtures at

Burning Rate
The burning velocities of methyl and isopropyl alcohol in air were determined by Gibbs and
Calcote for a range of mixture compositions at 25C; the maximum burning velocities were found
to be 50.4 and 41.4 cm/sec, respectively (68). These investigators also obtained the burning
velocities of methyl and n-propyl alcohol at 100C; the maximum values were 72.2 and
64.8 cm/sec, respectively. These values are in fair agreement with the corresponding values of
the paraffin hydrocarbons.
The methyl alcohol liquid-burning rate obtained from equation (53) is in fair agreement with that
obtained experimentally (fig. 52). The relatively low DHc/DHv ratios for the alcohols indicates that
they should be characterized by low-burning rates in large pools.

Not for Resale
125
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 79Limits of Flammability of tert-Butyl Alcohol-Water Vapor-Air Mixtures

--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
126
Figure 80Limits of Flammability of tert-Butyl Alcohol-Carbon Dioxide-Oxygen

Mixtures at 150C and Atmospheric Pressure.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
127
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 81Limits of Flammability of 2-Ethyl-butanol-Nitrogen-Oxygen Mixtures at


Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
128
--`,,```,,,,````-`-`,,`,,`,`,,`---
ETHERS (CnH2n+1OCmH2m+1)
Limits in Air
The properties of a few common ethers are listed in table 14. Unfortunately, the limits data show
appreciable scatter, so it is difficult to establish any general rules with the given data. However,
as a first approximation, the L25/Cst is about 0.5 for the simple ethers.
Because of the importance of ethers as anesthetics, limits of flammability were determined in
several atmospheres. The limits of the systems dimethyl ether-Freon-12 (CCl2F2)-air, dimethyl
ether-carbon dioxide-air, and dimethyl ether-nitrogen-air obtained by Jones and coworkers are
given in figure 82 (114); the limits of the systems diethyl ether-carbon dioxide-air and diethyl
ether-nitrogen-air are given in figure 83 (26, 106, 108). Cool flames exist above the upper limit as
noted; the upper limit of the cool flame region in air is 48.4 volume-percent, according to
Burgoyne and Neale (26). The limits of the systems diethyl ether-helium-oxygen and diethyl
ether-nitrous oxide-oxygen are given in figure 84 and the limits of diethyl ether-helium-nitrous
oxide are given in figure 85 (106). Again, as with the alcohols, more inert is needed to assure the
formation of nonflammable mixtures than is needed for the corresponding paraffin hydrocarbons.
Also, cool flames are encountered at lower temperatures and pressures.
Figure 82Limits of Flammability of Dimethyl Ether-Carbon Dioxide-Air and

Dimethyl Ether-Nitrogen-Air Mixtures at 25C and Atmospheric Pressure.

Not for Resale
129
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 83Limits of Flammability of Diethyl Ether-Carbon Dioxide-Air and Diethyl

Ether-Nitrogen-Air Mixtures at 25C and Atmospheric Pressure.
Table 14 Properties of selected ethers

Lower limit in air
Combustible
Dimethyl ether
Formula
Sp gr
(Air=1)
Cst in air
(vol pct)
Net DHc
Kcal
( ----------mole )
L25
(vol pct)
L
25
--------C
st
CH3OCH3
46.07
1.59
6.53
316
3.4
.52
Diethyl ether
C2H5OC2H5
74.12
2.56
3.37
605
1.9
.56
Ethyl propyl
ether
C2H5OC3H7
88.15
3.28
2.72
3750
1.7
.62
Di-i-propyl ether
C3H7OC3H7
102.17
3.53
2.27
5900
1.4
.57
Divinyl ether
C2H3OC2H3
70.09
2.42
4.02
31,770
1.7
.42
mg
L -------
1
Upper limit in air
Ref.
U25
(vol pct)
72
47
(114)
27
64
50
(40)
236
68
56
(26)
49
60
51
(40)
54
42
(97)
7.9
27
1 L*
M 16
= L ----------------- .
M
Cool Flames: U25=53 vol pct.
3Calculated value.
4
Cool flames:U25>16 vol pct.
5
Ref.(155).
2
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
U
25
---------C
st
mg
U -------
1
4.1
760
(114)
1880
(40)
3.3
390
(26)
3.5
290
(40)
6.7
1160
(97)
11
Ref.
ANSI/ISA-TR12.13.01-1999 (R2005)
130
Figure 84Limits of Flammability of Diethyl Ether-Helium-Oxygen and Diethyl

Ether-Nitrous Oxide-Oxygen Mixtures at 25C and Atmospheric Pressure.
Comparison of curves in figures 84 and 85 shows that the minimum oxidant requirement for the
formation of flammable diethyl ether-helium-oxidant mixtures is approximately twice as great with
nitrous oxide as with oxygen. However, if 1 mole of nitrous oxide furnishes one-half mole of
oxygen during combustion, then the minimum oxygen contents in the two cases are nearly equal.
Unfortunately, the available data are too meager to permit a more detailed comparison.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
131
ANSI/ISA-TR12.13.01-1999 (R2005)
Autoignition
In general, ethers are readily ignited by hot surfaces. These combustibles usually have a lower
ignition temperature in air and in oxygen than do the corresponding paraffins and alcohols. The
available autoignition temperature data are included in Appendix A.
Since the ethers tend to form peroxides under a variety of conditions, they may appear to be
unstable at room temperature (233).
Figure 85Limits of Flammability of Diethyl Ether-Nitrous Oxide-Helium Mixtures

--`,,```,,,,````-`-`,,`,,`,`,,`---
ESTERS (CnH2n1OOCmH2m+1)
The properties of several esters are listed in table 15. The ratio of the lower limit at 25C to the
stoichiometric concentration is about 0.55 for many of these compounds. This is the same ratio
as in equation (21) for paraffin hydrocarbons. The lower limit values expressed in terms of the
weight of combustible per liter of air (see section about alcohols) are listed in parentheses under
L(mg/1). These are larger than the corresponding values for the hydrocarbons and alcohols.
The inert requirements and minimum oxygen requirements for the first member of the series,
methyl formate, are nearly the same as for methyl alcohol and dimethyl ether (figs. 76, 82, 86).
This is not true of the other members for which data compiled at the Explosives Research Center
are availableisobutyl formate and methyl acetate (figs. 87, 88). Accordingly, it is rather difficult
to make additional generalizations for this series.
The autoignition temperatures of many esters in air and oxygen at atmospheric pressure are
given in Appendix A. In general, the AIT values of the esters are lower than are those of the
corresponding paraffins.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
132
Table 15 Properties of selected esters

Lower limit in air
r
Combustible
Formula
Sp gr
(Air=1)
Cst in air
(vol pct)
Net DHc
Kcal
( ----------mole )
L25
(vol pct)
--`,,```,,,,````-`-`,,`,,`,`,,`---
(111)
23.0
2.4
800
(111)
95
(40)
16.0
2.8
630
(40)
79
(40)
8.2
2.6
410
(40)
106
160
(40)
16.0
2.8
630
(40)
88
(40)
11.0
2.7
510
(175)
83
(40)
2.6
400
(40)
73
(5)
3.1
450
(5)
65
(5)
3.3
440
(5)
97
(40)
13.0
580
(40)
83
(40)
11.0
510
(40)
2.07
9.48
219
5.0
.53
Ethyl formate
HCOOC2H5
74.08
2.56
5.65
367
2.8
.50
n-Butyl formate
HCOOC4H9
102.13
3.53
3.12
650
1.7
.54
Methyl acetate
CH3COOCH3
74.08
2.56
5.65
358
3.2
.57
Ethyl acetate
CH3COOC2H5
88.10
3.04
4.02
504
2.2
.55
n-Propyl acetate
CH3COOC3H7
102.13
3.53
3.12
1.8
.58
n-Butyl acetate
CH3COOC4H9
116.16
4.01
2.55
n-Amyl acetate
CH3COOC5H11
130.18
4.50
2.16
Methyl propionate
C2H5COOCH3
88.10
3.04
4.02
Ethyl propionate
C2H5COOC2H5
102.13
3.53
3.12
1.4
.51
2.4
.60
650
1.8
.58
2Calculated

.55
1.0
M 16
= L ----------------- .
M
value.
3
t = 90C.
4t = 100C.
5Figures compiled by Explosives Res. Center, Federal Bureau of Mines
6P = 0.5 atm.
1
142
166
60.05
650
Not for Resale
U
25
---------C
st
mg
L -------
1
HCOOCH3
U25
(vol
pct)
L
25
--------C
st
Methyl formate
Upper limit in ai
154
150
156
157
Ref.
153
149
162
157
8.0
8.0
7.1
3.2
3.5
mg
U -------
1
Ref.
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
133
Figure 86Limits of Flammability of Methyl Formate-Carbon Dioxide-Air and

Methyl Formate-Nitrogen-Air Mixtures.

Not for Resale
134
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 87Limits of Flammability of Isobutyl Formate-Carbon Dioxide-Air and

Isobutyl Formate-Nitrogen-Air Mixture.

Not for Resale
135
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 88Limits of Flammability of Methyl Acetate-Carbon Dioxide-Air and

Methyl Acetate-Nitrogen-Air Mixtures.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
136
Figure 89Effect of Temperature on Lower Limits of Flammability of MEK-Toluene

Mixtures in Air at Atmospheric Pressure.
ALDEHYDES AND KETONES (CnH2nO)
Zabetakis, Cooper, and Furno found that the lower limits of methyl ethyl ketone (MEK) and MEKtoluene mixtures vary linearly with temperature between room temperature and 200C (235). A
summary of these data is given in figure 89; broken curves in this figure were obtained from the
modified Burgess-Wheeler law, equation (33), taking the lower limit at 100C as the reference
value. Similar data were obtained for tetrahydrofuran (THF) and THF-toluene mixtures (fig. 90).
In addition, it was shown that the systems MEK-toluene and THF-toluene obey Le Chatelier's
law, equation (46). Calculated and experimental values for the preceding systems in air are
given in figures 91 and 92.
The limits of the systems acetone-carbon dioxide-air, acetone-nitrogen-air, MEKchlorobromomethane (CBM)-air , MEK-carbon dioxide-air, and MEK-nitrogen-air are given in
figures 93 and 94. The data in these figures were obtained by Jones and coworkers (238).

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
Properties of some aldehydes and ketones are given in table 16. The ratio of the lower limit at
25C in air to the stoichiometric composition is approximately 0.5.
137
ANSI/ISA-TR12.13.01-1999 (R2005)
Table 16 Properties of selected aldehydes and ketones

Lower limit in air
Combustible
Formula
--`,,```,,,,````-`-`,,`,,`,`,,`---
Sp gr
(Air=1)
Cst in air
(vol pct)
Net DHc
Kcal
( ----------mole )
L25
(vol pct)
L
25
--------C
st
mg
L -------
1
Upper limit in air

U25
(vol pct)
Ref.
U
25
---------C
st
mg
U -------
1
Ref.
Acetaldehyde
CH3CHO
44.05
1.52
7.73
264
4.0
.52
82
(223)
4.7
1,100
(26)
Propionaldehyde
C2H5CHO
58.08
2.01
4.97
409
2.9
.59
77
(26)
2.8
420
(26)
36
14
Paraldehyde
(CH3CHO)3
132.16
4.56
2.72
1.3
.48
78
(40)
Acetone
CH3COCH3
58.08
2.01
4.97
403
2.6
.52
70
(98)
13
2.6
390
(98)
Methyl ethyl ketone
CH3COC2H5
72.10
2.49
3.67
548
1.9
.52
62
(235)
10
2.7
350
(223)
Methyl propyl
ketone
CH3COC3H7
86.13
2.97
2.90
692
1.6
.55
63
(40)
2.8
340
(40)
Diethyl ketone
C2H5COC2H5
86.13
2.97
2.90
692
1.6
.55
63
(3)
8.0
3.3
390
(40)
Methyl butyl ketone
CH3COC4H9
100.16
3.46
2.40
840
1.4
.58
64
(40)
8.2
Cool flames: U25=60 vol pct.

Cool flames: U25=17 vol pct.
Calculated value.
4t=50 C.
5
t=100 C.
2
3
Figure 90Effect of Temperature on Lower Limits of Flammability of THF-Toluene

Mixtures in Air at Atmospheric Pressure.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
138
The autoignition temperatures of various aldehydes and ketones in oxygen and air at
atmospheric pressure are given in Appendix A. In general, the AIT values are lower than those of
the corresponding paraffins.
SULFUR COMPOUNDS
The pertinent properties of sulfur compounds are given in table 17. In general, they have wide
flammable ranges and relatively low ignition temperatures (Appendix A).
Flammability diagrams are given for carbon disulfide mixed with carbon dioxide-air, water vaporair (239) and nitrogen-air (fig. 95); hydrogen sulfide-carbon dioxide-air (fig. 96); and ethyl
mercaptan with chlorodifluoromethane and dichlorodifluoromethane in air (117) (fig. 97). Figure
95 is interesting in that it shows not only the wide flammable range of carbon disulfide in air but
also the large quantities of inert required to prevent the formation of flammable mixtures.
FUELS AND FUEL BLENDS
Fuels used for propulsion, not covered in other sections, are considered here (table 18).
Ammonia and Related Compounds
This series includes ammonia (NH3), hydrazine (N2H4), monomethylhydrazine (N2H3CH3) and
unsymmetrical dimethylhydrazine (N2H2(CH3)2).
Ammonia forms flammable mixtures with air and other oxidants in a variety of concentrations, as
noted in table 19. White (225) and more recently, Buckley and Husa, (19) reported that, as with
hydrocarbons, an increase in either temperature or pressure tends to widen the flammable
range. Further, White found that the lower limit flame temperature remains essentially constant
with increase in initial temperature.
--`,,```,,,,````-`-`,,`,,`,`,,`---
Table 17 Properties of selected sulfur compounds

Lower limit in air
Combustible
Hydrogen Sulfide
Formula
H2S
34.08
Sp gr
(Air=1)
1.18
Cst in air
(vol pct)
12.25
Net DHc
Kcal
( ----------mole )
145
L25
(vol pct)
4.0
Upper limit in air

U25
(vol pct)
L
25
--------C
st
mg
L -------
1
.33
63
(1)
Ref.
U
25
---------C
st
mg
U -------
1
44
3.6
1,190
(1)
Ref.
Carbon disulfide
CS2
76.13
2.63
6.53
252
1.3
.20
45
(239)
50
7.7
3,400
(223)
Methyl mercaptan
CH3SH
48.10
1.66
6.53
276
3.9
.60
87
(1)
22
3.4
600
(1)
Ethyl mercaptan
C2H5SH
62.13
2.15
4.45
492
2.8
.63
80
(104)
18
4.4
610
(104)
62
(1)
20
4.5
690
(1)
Dimethyl sulfide
CH3SCH3
62.13
2.15
4.45
2.2
Figures compiled at Explosives Res. Center, Federal Bureau of Mines.

Not for Resale
.50
139
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 91Effect of Liquid Composition on Lower Limits of Flammability of MEKToluene Mixtures in Air at 30 and 200C.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
140
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 92Effect of Liquid Composition on Lower Limits of Flammability of

THF-Toluene Mixtures in Air at 30 and 200C.

Not for Resale
141
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 93Limits of Flammability of Acetone-Carbon Dioxide-Air and

Acetone-Nitrogen-Air Mixtures.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
142
--`,,```,,,,````-`-`,,`,,`,`,,`---
Table 18 Properties of selected fuels and fuel blends

Lower limit in air
Combustible
Sp gr
(Air=1)
Cst in
air (vol
pct)
Net DHc
L25
(vol pct)
Upper limit in air

Ref.
U25
(vol pct)
Ref.
Formula
Ammonia
NH3
17.03
0.59
21.83
0.69
134
(167)
28
1.3
Hydrazine
N2H4
32.05
1.11
17.32
4.7
.27
70
(188)
100
5.8
Monomethylhydrazine
N2H3CH3
46.07
1.59
7.73
.52
86
(218)
Unsymmetrical
dimethylhydrazine
N2H2(CH3)2
60.10
2.08
4.97
.40
55
(166)
95
19.1
(218)
Diborane
B2H6
27.69
.96
6.53
478
.12
10
(163)
88
13.5
(163)
Kcal
( -----------mole )
15
.8
L
25
--------C
st
mg
L -------
1
U
25
---------C
st
mg
U -------
1
300
(182)
(218)
.4
.11
10
(1)
.42
.12
12
.2
.11
11
(1)
Tetraborane
B4H10
53.36
1.84
3.67
Pentaborane
B5H9
63.17
2.18
3.37
1030
Decaborane
B10H14
122.31
4.23
1.87
Aviation gasoline
100/130
1.3
(241)
7.1
(241)
Aviation gasoline
115/145
1.2
(241)
7.1
(241)
Aviation jet fuel JP-1
(241)
(241)
(241)
(241)
.07
29.53
Hydrogen
1Calculated
2t
3t
H2
2.016
1.4
1.3
57.8
4.0
value.
= 150C.
= 100C.

Not for Resale
48
.14
48
(241)
46
(127)
3.7
(40)
8
8
75
380
2.54
330
(241)
290
(127)
270
(224)
143
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 94Limits of Flammability of Methyl Ethyl Ketone (MEK) Chlorobromomethane (CBM)-Air, MEK-Carbon Dioxide, Dioxide-Air and MEKNitrogen-Air Mixtures at 25 C and Atmospheric Pressure.
Table 19 Limits of flammability of ammonia at room temperature and near

atmospheric pressure.
Oxidant
Cst
Ref.
Air
21.8
15
28
(167, 182)
Oxygen
57.1
15
79
(225)
Nitrous oxide
40.0
2.2
72
(109)
Hydrazine vapor burns in the absence of an oxidizer, so that it has no upper limit and can
therefore be used as a monopropellant. The decomposition flame yields hydrogen, nitrogen, and
ammonia (64, 73). However, hydrazine vapor can be rendered nonflammable by addition of
stable diluents or inhibitors. The amount of diluent required at any temperature and pressure

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
144
appears to be governed in part by the ignition source strength. With a 0.25-inch spark gap and a
15,000-volt, 60-ma-luminous-tube transformer as the energy source, Furno, Martindill, and
Zabetakis (63) found that the following quantities of hydrocarbon vapor were needed to inhibit
flame propagation in a 1 1/4-inch glass tube" at 125C and atmospheric pressure: 39.8 pct
benzene; 35.0 pct toluene; 27.3 pct m-xylene; 23.8 pct cumene; 21.0 pct n-heptane. On this
same basis, 95.3 pct air is needed to revent flame propagation (188); this corresponds to a lower
limit of flammability of 4.7 pct hydrazine vapor. The flammable range in air at atmospheric
pressure is presented graphically in figure 98, which also gives the flammable ranges of
monomethylhydrazine, unsymmetrical dimethylhydrazine, and ammonia for comparison (218).
The flammability diagram for the system hydrazine-n-heptane-air at 125C and atmospheric
pressure is given in figure 99. These data were also obtained in a 1 1/4-inch glass tube.
A summary of the autoignition temperature data obtained by Perlee, Imhof, and Zabetakis (166)
for hydrazine, MMH, and UDMH in air and nitrogen dioxide (actually, the equilibrium mixture
NO*2 NO 2 + N 2 O 4 ) is given in figure 100; short horizontal lines indicate the uncertainty in
NO*2 concentrations. These materials may ignite spontaneously at room temperature with
relatively small NO*2 concentrations in the air; at 25C, liquid UDMH ignites in NO2*-air
atmospheres that contain more than about 8 volume-percent NO*2 ; MMH and hydrazine ignite in
atmospheres that contain more than about 11 and 14 volume percent NO*2 , respectively. In
general, even smaller concentrations of NO*2 produce spontaneous ignition of these
combustibles at higher initial combustible liquid temperatures. The effect of the hydrazine liquid
temperature on the spontaneous ignition temperature in NO*2 -air atmospheres is illustrated in
figure 101. Similar data are given in figures 102 and 103 for MMH and UDMH; there is an
apparent anomaly in the data obtained with MMH at 36, 55, and 67C.
--`,,```,,,,````-`-`,,`,,`,`,,`---
"
Comparable results were partially obtained in a 2-inch tube.

Not for Resale
145
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 95Limits of Flammability of Carbon Disulfide-Carbon Dioxide-Air, Carbon

Dioxide-Nitrogen-Air Mixtures at 25C and Atmospheric Pressure, and Carbon
Disulfide-Water Vapor-Air at 100C and Atmospheric Pressure.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
146
Figure 96Limits of Flammability of Hydrogen Sulfide-Carbon Dioxide-Air

Mixtures at 25C and Atmospheric Pressure.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
147
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 97Limits of Flammability of Ethyl Mercaptan-F-12-Air and Ethyl

Mercaptan-F-22-Air Mixtures at Atmospheric Pressure and 27C.
The use of various helium-oxygen atmospheres in place of air results in the spontaneous ignition
temperature curves given in figure 104 for UDMH. Comparison of curve B of this set with curve A
of figure 100 indicates that the spontaneous ignition temperature of UDMH in NO*2 -He-O2
atmospheres is the same as that obtained in NO*2 -air atmospheres.
Ignition temperature data obtained with UDMH in NO*2 -air mixtures at 15 and 45 psia are
summarized in figure 105. These indicate that although the spontaneous ignition temperature of
UDMH in air is not affected appreciably by this pressure change, it is affected in a range of NO*2 air mixtures.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
148
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 98Limits of Flammability of Ammonia, UDMH, MMH, and Hydrazine at

Atmospheric Pressure in Saturated and Near-Saturated Vapor-Air Mixtures.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
149
Figure 99Flammable Mixture Compositions of Hydrazine-Heptane-Air at 125C

and Approximately Atmospheric Pressure.

Not for Resale
150
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 100Minimum Spontaneous Ignition Temperatures of Liquid Hydrazine,

MMH, and UDMH at an Initial Temperature of 25C in Contact With NO*2 -Air
Mixtures at 74010 mm Hg as a Function of NO*2 Concentration.
The data presented in figures 100 to 105 were obtained with liquid fuel in contact with vaporized
NO*2 in air. Similar data obtained with vaporized UDMH-air in contact with NO*2 are given in
figure 106. This figure indicates UDMH-air mixtures that contain more than 9 volume-percent
UDMH will ignite spontaneously on contact with NO*2 ; UDMH-air mixtures that contain more than
approximately 2 volume-percent UDMH can be ignited by an ignition source under the same
conditions (166).

Not for Resale
151
ANSI/ISA-TR12.13.01-1999 (R2005)
Boron Hydrides
This series includes diborane (B2H6), tetraborane (B4H10), pentaborane (B5H9), and decaborane
(B10H14). However, reliable upper and lower limit data are available only on the first member of
this series at the present time. These were obtained by Parker and Wolfhard (163) who
determined the limits of flammability of diborane in air in a 5-cm-diameter tube at an initial
pressure of 300 mm Hg; this combustible forms flammable mixtures in air in the range from 0.8 to
87.5 volume-percent. A pale blue flame propagated throughout the tube at the upper limit;
luminous flames were not visible above 79 volume-percent. Limit of flammability curves for the
system diborane-ethane-air are presented in rectangular coordinates in figure 107. Except for
the slight dip to the ethane-axis (zero diborane) in the area in which ethane forms flammable
mixtures in air, these curves are rather similar to those obtained with other combustible-oxidantinert systems. Burning velocities in excess of 500 cm/sec were measured in this same study for
fuel-rich diborane-air mixtures.
Berl and Renich have prepared a summary report about boron hydrides (9). It includes data
obtained by these and other authors; they found the lower limit of pentaborane in air to be 0.42
volume-percent.
The autoignition temperature of diborane in air is apparently quite low. Price obtained a value of
135 C at 16.1 mm Hg (169); that of pentaborane is 30 C at about 8 mm Hg (9).
Gasolines, Diesel and Jet Fuels
Even relatively nonvolatile high-flashpoint oils may liberate flammable vapors at such a slow rate
that the closed vapor space above the liquid may be made flammable at reduced temperatures.
Gasolines can produce flammable saturated vapor-air mixture at temperatures below 65 C
(241), although the flash points of such fuels are considered to be about 45 C (158). An
apparent discrepancy thus exists if flashpoint data are used to predict the lowest temperature at
which flammable mixtures can be formed in a closed vapor space above a blend in long-term
storage.
As noted earlier, the limits of flammability of hydrocarbon fuels are not strongly dependent on
molecular weight when the limits are expressed by weight. However, since results measured by
a volume are perhaps more widely used than those measured by weight, typical flammability
curves are presented by volume for the light fractions from aviation gasoline, grade 115/145 (fig.
109), and aviation jet fuel, grade JP-4 (fig. 110). Combustible vapor-air-carbon dioxide and
vapor-air-nitrogen mixtures at about 25 C and atmospheric pressure are considered for each.
Similar data are given in figure 14 for the gasoline vapor-air-water vapor system at 21 and 100

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
Fuels considered in this section are blends that contain a wide variety of hydrocarbons and
additives. Accordingly, their flammability characteristics are governed by the method used to
extract a vapor sample as well as by the history of the liquid. For example, since the lower limit of
flammability, expressed in volume-percent, is inversely proportional to the molecular weight of
the combustible vapor, equation (28), the first vapors to come from a blend, such as gasoline,
give a higher lower limit value than the completely vaporized sample. Conversely, the heavy
fractions or residue give a smaller lower limit value. For this reason, there is some disagreement
about the limits of flammability of blends such as gasoline and the diesel and jet fuels. These
fuels are, in general, characterized by a wide distillation range; the ASTM distillation curves of
two gasolines and three jet fuels considered here are given in figure 108. Unfortunately, such
curves give only an approximate measure of the volatile constituents in the liquid blend.
ANSI/ISA-TR12.13.01-1999 (R2005)
152
C; the effect of pressure on limits of flammability of volatile constituents of JP-4 vapor in air are
discussed in connection with figure 12.
Minimum autoignition temperatures of gasolines and jet fuels considered here are given in
compilations by Zabetakis, Kuchta, and coworkers (126, 237). These data are included in
table 20.
--`,,```,,,,````-`-`,,`,,`,`,,`---
Setchkin (194) determined the AIT values of four diesel fuels with cetane numbers of 41, 55, 60
and 68. These data are included in table 20. Johnson, Crellin, and Carhart (92, 93) obtained
values that were larger than those obtained by Setchkin, using a smaller apparatus.

Not for Resale
153
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 101Minimum Spontaneous Ignition Temperatures of Liquid Hydrazine at

Various Initial Temperatures in NO*2 -Air Mixtures at 74010 mm Hg as a Function
of NO*2 Concentration.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
154
Figure 102Minimum Spontaneous Ignition Temperatures of Liquid MMH at

Various Initial Temperatures in NO 2* -Air Mixtures at 74010 mm Hg as a Function
of NO 2* Concentration.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 103Minimum Spontaneous Ignition Temperatures of Liquid UDMH at

Various Initial Temperatures in NO 2* -Air Mixtures at 74010mm Hg as a Function
of NO 2* Concentration.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
155
ANSI/ISA-TR12.13.01-1999 (R2005)
156
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 104Minimum Spontaneous Ignition Temperatures of 0.05 cc of Liquid

UDMH in He-O2- NO 2* Atmospheres at 1 Atmosphere for Various He/O2 Ratios.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
157
Figure 105Minimum Spontaneous Ignition Temperatures of 0.05 cc of Liquid

UDMH in NO 2* -Air Mixtures at 15 and 45 Psia as a Function of NO 2* Concentration.

Not for Resale
158
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 106Minimum Spontaneous Ignition Temperatures of Vaporized UDMH-Air

Mixtures in Contact With 100 pct NO 2* at 25 C and 74010 mm Hg as a Function of
UDMH Concentration in Air.

Not for Resale
159
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 107Limits of Flammability of Diborane-Ethane-Air Mixtures at Laboratory

Temperatures and 300 mm Hg Initial Pressure.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
160
Figure 108ASTM Distillation Curves for, A, Aviation Gasoline, Grade 100/130;

B, Aviation Gasoline, Grade 115/145; C, Aviation Jet Fuel, Grade JP-1;
D, Aviation Jet Fuel, Grade JP-3; and E, Aviation Jet Fuel, Grade JP-4.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
161
Figure 109Limits of Flammability of Aviation Gasoline, Grades 115/145

Vapor-Carbon Dioxide-Air and 115/145 Vapor-Nitrogen-Air, at 27C and

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
162
Figure 110Limits of Flammability of JP-4 Vapor-Carbon Dioxide-Air and JP-4

Vapor-Nitrogen-Air Mixtures at 27C and Atmospheric Pressure.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
163
ANSI/ISA-TR12.13.01-1999 (R2005)
Table 20 Autoignition temperature values of various fuels in air at 1 atmosphere

Fuel:
AIT, C
Aviation gasoline:
100/130
440
115/145
471
Aviation jet fuel:

JP-1
228
JP-3
238
JP-4
242
JP-6
232
Diesel fuel:
41 cetane
233
55 cetane
230
60 cetane
225
68 cetane
226
Burning velocities of the fuels considered here are in the same range as those of the
hydrocarbons considered earlier. Values for various fuels have been tabulated by Barnett and
Hibbard (156).
Hydrogen
--`,,```,,,,````-`-`,,`,,`,`,,`---
Numerous flammability characteristics studies have been conducted with hydrogen in recent
years. Drell and Belles have prepared an excellent survey of these characteristics (48). This
survey includes all but the most recent work of interest.
The low pressure limits of flame propagation for stoichiometric hydrogen-air mixtures are
somewhat lower than those for stoichiometric ethylene-air mixtures (197) in cylindrical tubes. In
the range from 6 to 130 mm Hg, the limit for stoichiometric hydrogen-air mixtures is given by the
expression:
log P=3.191.19 log D,
(57)
where P is the low-pressure limit in millimeters of Hg, and D is the tube diameter in millimeters.
Hydrogen forms flammable mixtures at ambient temperatures and pressures with oxygen, air,
chlorine, and the oxides of nitrogen. Limits of flammability in these oxidants at approximately
25C and 1 atmosphere are listed in table 21.
Flammability diagrams of the systems hydrogen-air-carbon dioxide and hydrogen-air-nitrogen
obtained by Jones and Perrott (112) are given in figure 111. Lines that establish minimum
oxygen values for each system are also included. Note that although the minimum value occurs

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
164
near the "nose" of the hydrogen-air-nitrogen curve, the corresponding value occurs at the upper
limit of the hydrogen-air-carbon dioxide curve.
Flammability diagrams obtained by Scott, Van Dolah, and Zabetakis for the systems hydrogennitric oxide-nitrous oxide, hydrogen-nitrous oxide-air, and hydrogen-nitric oxide-air are given in
figures 112-114 (189). Upper limit curves were found to deviate from the results obtained from the
Le Chatelier law, broken curves; additional data are given in the original article.
Table 21 Limits of flammability of hydrogen in various oxidants

at 25C and atmospheric pressure
L25
U25
Ref.
Oxygen
4.0
95
(40)
Air
4.0
75
(40)
Chlorine
4.1
89
(216, 128)
N2O
3.0
84
(189)
NO
6.6
66
(189)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Oxidant

Not for Resale
165
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 111Limits of Flammability of Hydrogen-Carbon Dioxide-Air and

Hydrogen-Nitrogen-Air Mixtures at 25C and Atmospheric Pressure.
The burning velocity of hydrogen in air at 25C and one atmosphere range from a low of a few
centimeters per second to 325 cm/sec (68). When liquefied, it vaporizes and burns in air at a
rate that is determined by the rate at which heat enters the liquid. Heat is abstracted from the
surroundings and, where a flame exists, from the flame itself. Figure 115 gives the results
obtained from vaporizing liquid hydrogen from paraffin cast in a Dewar flask; experimental points
were obtained from gas evolution measurements. The solid curve (theoretical) was obtained by
Zabetakis and Burgess by assuming the heat influx rate to be conduction limited (234); the initial
flash vaporization rates are probably film-and nucleate boiling-limited. The theoretical liquid
regression rates following spillage of liquid hydrogen onto three soils are presented in figure 116,
the corresponding decrease in liquid level is given in figure 117. Because of its low temperature,
the vaporized hydrogen forms a vapor trail as it leaves the liquid. However, the position of this
trail or visible cloud does not necessarily coincide with that of the flammable zones formed above
the liquid pool. This is illustrated in figure 118, in which the positions of the flammable zones and
visible clouds are defined in a height-elapsed time graph. Two flammable zones are defined
here. These are also seen in the motion picture sequence (fig. 119) of the visible clouds and
flames that resulted following spillage of 7.8 liters of liquid hydrogen and subsequent ignition of
vapors above the spill area. The height and width of fireballs that resulted from ignition of vapors
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
166
produced by rapid vaporization of about 3 to 90 liters of liquid hydrogen are given in figure 120.
The data are represented fairly well by the equation
H max = W max = 7 V1 feet = 17.8 M feet ,
(58)
where Hmax and Wmax are the maximum flame height and width, respectively, V1 is the volume of
liquid hydrogen in liters, and M is the mass of this volume in pounds.
The burning rate of a 6-inch pool of liquid hydrogen in air is given as the regression of the liquid
level in figure 121; burning rate data for liquid methane are included for comparison. An
extrapolated value of burning rate for large pools of liquid hydrogen is included in figure 52.
Approximate quantity-distance relationships can be established for the storage of liquid hydrogen
near inhabited buildings and other storage sites if certain assumptions are made (33, 160, 234).
Additional work is required to establish such distances for very large quantities of liquid.
--`,,```,,,,````-`-`,,`,,`,`,,`---
The detonation velocity and the static and reflected pressures developed by a detonation wave
propagating through hydrogen-oxygen mixtures are given in figure 16. The predetonation
distance in horizontal pipes is reportedly proportional to the square root of the pipe diameter
(229); this is presumably applicable to results obtained with a mild ignition source, since a shock
front can establish a detonation at essentially zero runup distance. Numerous investigators have
examined this and related problems in recent years (11-13, 65, 135-137, 151).

Not for Resale
167
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 112Limits of Flammability of H2-NO-N2O at Approximately 28C and

1 Atmosphere.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
168
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 113Limits of Flammability of H2-N2O-Air at Approximately 28C and

1 Atmosphere.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
169
Figure 114Limits of Flammability of H2-NO-Air at Approximately 28C and

1 Atmosphere.

Not for Resale
170
Figure 115Rate of Vaporization of Liquid Hydrogen From Paraffin in a 2.8-Inch

Dewar Flask: Initial Liquid Depth6.7 Inches.
HYDRAULIC FLUIDS AND ENGINE OILS
Both mineral oil derived and synthetic hydraulic fluids and engine oils are presently in common
use (148). These materials are often used at elevated temperatures and pressures and contain
additives designed to improve stability, viscosity, load-bearing characteristics, etc. Such
additives affect flammability characteristics of the base fluid. However, the base fluid generally
plays a predominant role in determining limits of flammability and ignition temperature of a
particular fluid. For example, many of the oil-based fluids have lower limits of flammability that
fall in the ranges given in figure 22 for paraffin hydrocarbons. Further, those that have minimum
autoignition temperatures in the lower temperature ranges considered in figures 43 and 71 are
not affected appreciably by oxygen concentration of the atmosphere and by ambient and fluidinjection pressures; those that have minimum autoignition temperatures in the higher
temperature ranges do not follow these generalizations (237). Since these fluids are designed
for use at elevated temperatures and pressures, they are normally made up of high-molecular
weight materials. Accordingly, they are flammable at ordinary temperatures and pressures as
mists and foams. Burgoyne and his coworkers (27) found that lubricating-oil mists were
flammable in air but not in carbon dioxide-air mixtures that contained about 28 volume-percent

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
171
ANSI/ISA-TR12.13.01-1999 (R2005)
carbon dioxide (fig. 35). At elevated temperatures, the oil vapors cracked and produced
acetylene and hydrogen, which affected the flammability of the resultant mixture; the vapors are
often unstable at elevated temperatures. Chiantella, Affens, and Johnson have determined the
effect of elevated temperatures on the stability and ignition properties of three commercial triaryl
phosphate fluids (36).
Zabetakis, Scott, and Kennedy have determined the effect of pressure on the autoignition
temperatures of commercial lubricants (248). Figure 122 gives the minimum autoignition
temperatures for four commercial phosphate ester-base fluids (curves 1-4) and three mineral oils
(curves 5-7). In each case, the minimum autoignition temperature was found to decrease with
increase in pressure over most of the pressure range considered. A plot of the logarithm of the
initial pressure to temperature ratio versus the reciprocal of the temperature is given for curves 1
to 7 in figure 123. The resultant curves are linear over a limited temperature range.
Figure 116Theoretical Liquid Regression Rates Following Spillage of Liquid

Hydrogen Onto, A, an Average Soil; B, Moist Sandy Soil (8 Pct. Moisture); and
C, Dry Sandy Soil.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
172
Figure 117Theoretical Decrease in Liquid Hydrogen Level Following Spillage

Onto, A, Dry Sandy Soil; B, Moist Sandy Soil (8 Pct. Moisture); and C, Average Soil.
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 118Extent of Flammable Mixtures and Height of Visible Cloud Formed

After Rapid Spillage of 3 Liters of Liquid Hydrogen on a Dry Macadam Surface in a
Quiescent Air Atmosphere at 15C.

Not for Resale
173
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 119Motion Picture Sequence (16 Frames per Second) of Visible Clouds
and Flames Resulting From Rapid Spillage of 7.8 Liters of Liquid Hydrogen on a
Gravel Surface at 18C. Ignition Source: 20 Inches Above Gravel.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
174
Figure 120Maximum Flame Height and Width Produced by Ignition of Vapor-Air

Mixtures Formed by Sudden Spillage of 2.8 to 89 Liters of Liquid Hydrogen (V1).
Figure 121Burning Rates of Liquid Hydrogen and of Liquid Methane at the

Boiling Points in 6-Inch-Pyrex Dewar Flasks.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
175
ANSI/ISA-TR12.13.01-1999 (R2005)
The ratio of the final temperature attained by air in an adiabatic compression process to the initial
temperature is given in figure 124 as a function of both the final-to-initial pressure ratio and initialto-final volume ratio. If a lubricating oil is exposed to high temperatures during a compression
process, autoignition may occur if the residence or contact time is adequate. Such high
temperatures do occur in practice and have been known to cause disastrous explosions (58,
146, 149, 227, 231). The curves in figure 125 show that in the compression pressure range 1 to
10 atmospheres (initial pressure=1 atmosphere), a wide range of ambient temperatures can lead
to the autoignition of a mineral oil lubricant (curve 5) if sufficient vapor or mist is in the system. In
the same pressure range, only elevated initial temperatures could lead to the autoignition of a
phosphate ester (curve 4). If the initial pressure is increased to 10 atmospheres, autoignition can
occur at lower air-intake temperatures in every case (248).
MISCELLANEOUS
The flammability characteristics of a number of miscellaneous combustibles not considered
elsewhere, are discussed in this section. These include carbon monoxide, n-propyl nitrate, and
the halogenated hydrocarbons. The properties of these and a great variety of other materials are
included in Appendix A.
The limits of flammability of the systems carbon monoxide-carbon dioxide-air and carbon
monoxide-nitrogen-air are presented in figure 126. These curves were constructed from the
flammability data obtained by Jones in a 2-inch vertical glass tube with upward flame propagation
(112); other representations may be found in the original reference and in the compilation
prepared by Coward and Jones (40).
The spontaneous ignition of NPN in air was considered earlier at 1,000 psig, (figs. 3, 4). The
explosion pressures obtained at this initial pressure in air and in a 10-volume-percent oxygen
+90-volume-percent nitrogen atmosphere at various NPN concentrations are presented in figure
129. A summary of the minimum spontaneous ignition and decomposition temperatures
obtained with NPN in air and nitrogen respectively are given in figure 130. The data given in this
figure exhibit a behavior that is typical of that found with other combustibles at elevated
pressures; the minimum spontaneous ignition temperature first decreases with initial increase in
pressure and then increases as the pressure is increased still further (120, 248).

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
Materials that are oxidized or decomposed readily may yield erratic flammability data under
certain conditions. This effect is illustrated in figure 127 which summarizes the lower-limits data
obtained by Zabetakis, Mason and Van Dolah with n-propyl nitrate (NPN) in air at various
temperatures and pressures (243). An increase in temperature from 75 to 125C is
accompanied by a decrease in the lower-limit values; a further increase in temperature to 150C
results in a further lowering of the lower limit at pressures below 100 psig, but not at the higher
pressures. An increase in the temperature to 170C results in an apparent increase in the lowerlimit value because of the slow oxidation of NPN. A complete flammability diagram has been
constructed for the NPN vapor system in figure 128; a single lower limit curve and two upper limit
curves are given here to show the effect of pressure on the flammable range of a vapor-air
system.
ANSI/ISA-TR12.13.01-1999 (R2005)
176
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 122Variation in Minimum Autoignition Temperature With Pressure of

Commercial Phosphate Ester and Mineral Oil Lubricants in Air in a
450-cc-Stainless Steel Bomb.

Not for Resale
177
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Figure 123Logarithm of Initial Pressure-AIT Ratio of Seven Fluids in Air for

Various Reciprocal Temperatures. Data from Figure 122.

Not for Resale
178
Figure 124Variation in Tf /Ti of Air With Vi /Vf and With Pf /Pi in an Adiabatic
Compression Process.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 125Variation In Air Temperature With Pf /Pi in an Adiabatic Compression

Process for Five Initial Air Temperatures (0, 25, 50, 75, and 100C). Regions of
autoignition for lubricants IV and V at Pf /Pi Between 1 and 10 Atmospheres and
Pi of Between 1 and 10 Atmospheres.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
179
ANSI/ISA-TR12.13.01-1999 (R2005)
180
Figure 126Limits of Flammability of Carbon Monoxide-Carbon Dioxide-Air and

Carbon Monoxide-Nitrogen-Air Mixtures at Atmospheric Pressure and 26C.
Although many of the halogenated hydrocarbons are known to be flammable (40) still others
such as methyl bromide, methylene chloride, and trichloroethylene (TCE) have been considered
to be nonflammable or essentially nonflammable in air. As noted in connection with the methyl
bromide data given in figure 28, Hill found methyl bromide to be flammable in air at 1 atmosphere
pressure (84); the reported limits of flammability were from 10 to 15 volume-percent methyl
bromide. At an initial pressure of 100 psig, the flammable range was found to extend from 6 to
25 volume-percent. Similarly, methylene chloride and trichloroethane were found to be
flammable in air at ambient temperatures although the flammable ranges were not determined.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
Burning velocities were found to range from 20 cm/sec to 110 cm/sec in NPN-air mixtures
containing 3.0 to 7.2 volume-percent NPN. Detonations were obtained in saturated NPN vaporair mixtures from 30 to 65C and 1 atmosphere pressure; the detonation velocity was from
1,500 to 2,000 meters per second. Stable detonations were obtained with liquid NPN at 90C; the
detonation velocity was from 4,700 to 5,100 meters per second.
181
ANSI/ISA-TR12.13.01-1999 (R2005)
In general, much higher source energies are required with these combustibles than are required
to ignite methane-air mixtures.
Figure 127Lower Limits of Flammability of NPN Vapor-Air Mixtures Over the

Pressure Range From 0 to 1,000 Psig at 75, 125, 150, and 170C.
An approximate flammability diagram was prepared by Scott for trichloroethylene-air mixtures

(190); a modification is reproduced in figure 131. The lower limit data were obtained in a vertical
7-inch-diameter flammability tube and the upper limit data in an 8-inch-diameter glass sphere
with upward propagation of flame. Flammable mixtures of TCE and air were also obtained
between 10.5 and 41 volume-percent TCE at 1 atmosphere and 100C in an 8-inch-diameter
glass sphere. Under the same conditions, flammable mixtures of TCE and oxygen were
obtained between 7.5 and 90 volume-percent TCE. However, additional work must be
conducted with this and the other halogenated hydrocarbons to determine the effect of vessel
size, ignition source strength, temperature and pressure on their flammability characteristics.
--`,,```,,,,````-`-`,,`,,`,`,,`---
Other useful flammability data may be found for various miscellaneous combustibles in many of
the publications listed in the bibliography (40, 154, 200, 208-214, 218). These include data on
the gases produced when metals react with water (56) and sulfur reacts with various
hydrocarbons (62). Still other references consider the hazards associated with the production of
unstable peroxides (142, 157, 187, 233) and other reactive materials (66, 74, 80, 139).

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
182
Figure 128Flammable NPN Vapor-Air Mixtures Formed Over the Pressure Range
From 0 to 1,000 Psig at 50 and 125C.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
183
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 129Variation of Explosion Pressure Following Spontaneous Ignition With

NPN Concentration, Initial Pressure 1,000 Psig.
Figure 130Minimum Spontaneous Ignition and Decomposition Temperatures of

n-Propyl Nitrate in Air as a Function of Pressure, Type 347 Stainless Steel
Test Chamber.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
184
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
Figure 131Flammability of Trichloroethylene-Air Mixtures.

Not for Resale
185
ANSI/ISA-TR12.13.01-1999 (R2005)
Acknowledgments
--`,,```,,,,````-`-`,,`,,`,`,,`---
Many of the unpublished data reported here were obtained by the predecessor of the author, the
late G. W. Jones, former chief of the gas explosions branch. Other data were obtained by the
author and his coworkers, particularly Messrs. George S. Scott, Joseph M. Kuchta, Aldo L.
Furno and Henry E. Perlee. In addition, the author is indebted to Drs. David Burgess" and Robert
W. Van Dolah for many fruitful discussions of the material contained in the sections on Definitions
and Theory, Deflagration and Detonation Processes, and Preventive Measures.
"
Presently with Reaction Motors Division, Thiokol Chemical Corporation, Denville, New Jersey.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
186
Bibliography
1)
Affens, W. A., J. E. Johnson, and H. W. Carhart. Effect of Chemical Structure on

Spontaneous Ignition of Hydrocarbons. J. Chem. Eng. Data, v. 6, 1961, pp. 613-619.
2)
_____. Ignition Studies, Part V, Study of the Processes Occurring During the
Spontaneous Ignition of the Hexane Isomers. NRL Rept. 5437, January 1960, 15 pp.
3)
Agnew, J. T., and L. B. Graiff. The Pressure Dependence of Laminar Burning Velocity
by the Spherical Bomb Method. Combustion and Flame, v. 5, 1961, pp. 209-219.
4)
Alexander, D. S. Explosions in Butadiene Systems. Ind. and Eng. Chem., v. 51, 1959,
pp. 733-738.
5)
Anson, D. Influence of the Quality of Atomization on the Stability of Combustion of

Liquid Fuel Sprays. Fuel, v. 32, 1953, pp. 39-51.
6)
Ashman, L. E., and A. Bchler. The Ignition of Gases by Electrically Heated Wires.
Combustion and Flame, v. 5, 1961, pp. 113-121.
7)
Bartkowiak, Alphonse, Sotirios Lambiris, and Michael G. Zabetakis. Flame

Propagation Through Kerosine Foams. Combustion and Flame, v. 3, 1959, pp. 347353.
8)
Bartkowiak, Alphonse, and Michael G. Zabetakis. Flammability Limits of Methane

and Ethane in Chlorine at Ambient and Elevated Temperatures and Pressure.
BuMines Rept. of Inv. 5610, 1960, 6 pp.
9)
Berl, W. G. and W. Renich. The Combustion of Boron Hydrides. CM-942, Johns

Hopkins Univ., Silver Spring, Md., 1958, 53 pp.
10) Block, Benjamin. Emergency Venting for Tanks and Reactors. Chem. Eng., January
1962, pp. 111-118.
11)
Bollinger, Loren E., and Rudolph Edse. Thermodynamic Calculations of HydrogenOxygen Detonation Parameters for Various Initial Pressures. ARS J., v. 31, 1961,
pp. 251-256.
12) Bollinger, Loren E., Michael G. Fong, and Rudolph Edse. Experimental Measurements
and Theoretical Analysis of Detonation Induction Distances. ARS J., 1961, pp. 588594.
13) Bollinger, Loren E., James A. Laughrey, and Rudolph Edse. Experimental Detonation
Velocities and Induction Distances in Hydrogen-Nitrous Oxide Mixtures. ARS J., v.
32, 1962, pp. 81-82.
14) British Chemical Engineering. Use of Bursting Discs at High Temperatures.
December 1957, p. 677.
16) Browne, Howard C., Harold Hileman, and Lowell C. Weger. Barricades for High
Pressure Research. Ind. and Eng. Chem., v. 53, 1961, pp.52A-58A.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
15) Brokaw, Richard S., and Joseph L. Jackson. Effect of Temperature, Pressure, and
Composition on Ignition Delays for Propane Flames. 5th Symp. (Internat.) on
Combustion, Reinhold Pub. Corp., New York, 1955, pp. 563-569.
187
ANSI/ISA-TR12.13.01-1999 (R2005)
17) Browning, J. A., and W. G. Krall. Effect of Fuel Droplets on Flame Stability, Flame
Velocity, and Inflammability Limits. 5th Symp. (Internat.) on Combustion, Reinhold
Pub. Corp., New York, 1955, pp. 159-163.
--`,,```,,,,````-`-`,,`,,`,`,,`---
18) Browning, J. A., T. L. Tyler, and W. G. Krall. Effect of Particle Size on Combustion of
Uniform Suspensions. Ind. and Eng. Chem., v. 49, 1957, pp. 142-148.
19) Buckley, William L., and Howard W. Husa. Combustion Propertiesof Ammonia.
Chem. Eng. Prog., v. 58, 1962, pp. 81-84.
20) Burgess, D., A. Strasser, and J. Grumer. Diffusive Burning of Liquid Fuels in Open
Trays. Fire Res. Abs. and Rev., v. 3, 1961, pp. 177-192.
21) Burgess, David, and Michael G. Zabetakis. Fire and Explosion Hazards Associated
With Liquefied Natural Gas. BuMines Rept. of Inv. 6099, 1962, 34 pp.
22) Burgoyne J. H. Mist and Spray Explosions. Chem. Eng. Prog., v. 53, 1957,
pp. 121-M-124-M.
23) _____. Principles of Explosion Prevention. Chem. and Process Eng., April 1961,
pp. 1-4.
24) Burgoyne, J. H., and L. Cohen. The Effect of Drop Size on Flame Propagation in
Liquid Aerosols. Roy. Soc. (London), Proc. v. 225, 1954, pp. 375-392.
25) Burgoyne, J. H., and H. Hirsch. The Combustion of Methane at High Temperatures.
Roy. Soc. (London), Proc. v. 227 1954, pp. 73-93.
26) Burgoyne, J. H., and R. F. Neale. Some New Measurements of Inflammability Ranges
in Air. Fuel, v. 32, 1953, pp. 5-16.
27) Burgoyne J. H., and J. F. Richardson. The Inflammability of Oil Mists. Fuel, v. 28,
1949, pp. 2-6.
28) Burgoyne, J. H., and A. J. Steel. Flammability of Methane-Air Mixtures in Water-Base
Foams. Fire Res. Abs. and Rev., v. 4, Nos. 1 and 2, 1962, pp. 67-75.
29) Burgoyne J. H., and G. Williams-Leir. The Influence of Incombustible Vapours on the
Limits of Inflammability of Gases and Vapours in Air. Roy. Soc. (London) Proc., v.
193, 1948, pp. 525-539.
30) Burgoyne, J. H., and M. J. G. Wilson. The Relief of Pentane Vapour-Air Explosions
in Vessels. Proc. Symp. on Chem. Process Hazards, Inst. Chem. Eng. (London),
1960, pp. 25-29.
31) Butler, Judson C., and William P. Webb. Upper Explosive Limits of Cumene. Chem.
Eng. Data, v. 2, 1957, pp. 42-46.
32) Cassutt, Leon H. Experimental Investigation of Detonation in Unconfined Gaseous
Hydrogen-Oxygen-Nitrogen Mixtures. ARS J., 1961, pp. 1122-1128.
33) Cassutt, L. H., F. E. Maddocks, and W. A. Sawyer. A Study of the Hazards in the
Storage and Handling of Liquid Hydrogen. Advances in Cryogenic Eng., ed. by K.
D. Timmerhaus. Plenum Press, Inc., New York, v. 5, 1960, pp. 55-61.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
188
34) Chemical and Engineering News. Explosive Decomposition of Propylene. V. 30,

1952, p. 1239.
35) Chemical Engineering. Pane Relievers Vent Explosive Popoffs. Jan. 22, 1962, pp.
70-72.
36) Chiantella, A. J., W. A. Affens, and J. E. Johnson. The Effect of High Temperatures
on the Stability and Ignition Properties of Commercial Triaryl Phosphate Fluids. NRL
Rept. 5839, 1962, 15 pp.
37) Coleman, E. H. Effects of Fluorinated Hydrocarbons on the Inflammability Limits of
Combustible Vapours. Fuel, v. 31, 1953, pp. 445-447.
38) Conison, Joseph. How to Design a Pressure Relief System. Chem. Eng., 1960, pp.
109-114.
39) Copeland, N. A., and M. A. Youker. German Techniques for Handling Acetylene in
Chemical Operations. FIAT Final Rept. No. 720, January 1946, 130 pp.
40) Coward, H. F., and G. W. Jones. Limits of Flammability of Gases and Vapors. BuMines
Bull. 503, 1952, 155 pp.
41) Coward, H. F., G. W. Jones, C. G. Dunkle, and B. E. Hess. The Explosibility of Methane
and Natural Gas. Carnegie Inst. of Technol., Min. and Met. Inv., Coop. Bull. 30,
1926, 40 pp.
42) Cubbage, P. A., and W. A. Simmonds. An Investigation of Explosion Reliefs for
Industrial Drying Ovens. Gas Council, Res. Communication GC23 (London), 1955,
46 pp.
43) _____. An Investigation of Explosion Reliefs for Industrial Drying Ovens. Gas Council,
Res. Communication GC43 (London), 1957, 41 pp.
44) Davenport, Donald E., George B. Huber, and Norman R. Zabel. Containment of
Fragments From Runaway Nuclear Reactors. Progress in Nuclear Energy, v. 4,
Pergamon Press, New York, 1961, pp. 484-503.
45) Davis, D. S. Emergency Vent Size for Tanks Containing Flammable Liquids. British
Chem. Eng. Nomogram No. 62, v. 6, 1961, p. 644.
46) Diss, E., H. Karam, and C. Jones. Practical Way to Size Safety Disks. Chem. Eng.,
1961, pp. 187-190.
47) Dixon-Lewis, G., and G. L. Isles. Limits of Flammability. 7th Symp. (Internat.) on
Combustion, Butterworths Scientific Pub. (London), 1959, pp. 475-483.
48) Drell, Isadore L., and Frank E. Belles. Survey of Hydrogen Combustion Properties.
Nat. Advisory Committee for Aeronautics Rept. 1383, 1958, 34 pp.
49) Dugger, Gordon L., and Dorothy D. Graab. Flame Velocities of Propane- and
Ethylene-Oxygen-Nitrogen Mixtures. Nat. Advisory Committee for Aeronautics RM
E52J24, January 1953, 23 pp.
50) Dugger, Gordon L., and Sheldon Heimel. Flame Speeds of Methane-Air, PropaneAir, and Ethylene-Air Mixtures at Low Initial Temperatures. Nat. Advisory Committee
for Aeronautics TN 2624, February 1952, 25 pp.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
189
ANSI/ISA-TR12.13.01-1999 (R2005)
51) Dugger, Gordon L., Robert C. Weast, and Sheldon Heimel. Effect of Preflame
Reaction on Flame Velocity of Propane-Air Mixtures. 5th Symp. (Internat.) on
52) Dunn, Robert G., and Bernard T. Wolfson. Single Generalized Chart of Detonation
Parameters for Gaseous Mixtures. J. Chem. and Eng. Data, v. 4, 1959, pp. 124-127.
53) Dvorak, Karel, and Arnost Reiser. Influence of Water Vapor on the Flame Extinction
of Methanol in Air. Chem. Listy, v. 49, 1955, pp. 467-472.
--`,,```,,,,````-`-`,,`,,`,`,,`---
54) Edwards, D. H., G. T. Williams, and J. D. Breeze. Pressure and Velocity

Measurements on Detonation Waves in Hydrogen-Oxygen Mixtures. J. Fluid Mech.,
November 1959, pp. 497-517.
55) Egerton, Sir Alfred C. Limits of Inflammability. 4th Symp. (Internat.) on Combustion,
Williams & Wilkins Co., Baltimore, Md., 1953, pp. 4-13.
56) Epstein, Leo F. Correlation and Prediction of Explosive Metal-Water Reaction
Temperatures. Nuclear Sci. and Eng., v. 10, July 1961, pp. 247-253.
57) Evans, Marjorie W., and C. M. Ablow. Theories of Detonation. J. Chem. Rev., v. 129,
1961, pp. 129-178.
58) Faeth, G. M., and D. F. White. Ignition of Hydraulic Fluids by Rapid Compression.
Am. Soc. Naval Eng. J., v. 73, 1961, pp. 467-475.
59) Fitzgerald, F. Decomposition of Methylacetylene. Nature, 1960, p. 387.
60) Frank, Charles E., and Angus U. Blackham. Investigation of Hydrocarbon Ignition.
Nat. Advisory Committee for Aeronautics TN 2549, 1952, 33 pp.
61) Fraser, R. P. Detonation Velocities in Liquid Fuel Vapours With Air or Oxygen at 100C
and Atmospheric Pressure. 7th Symp. (Internat.) on Combustion, Butterworths Sci.
Pub. (London), 1958, pp. 783-788.
62) Furno, Aldo L., George H. Martindill, and Michael G. Zabetakis. Gas Explosion
Hazards Associated With the Bulk Storage of Molten Sulfur. BuMines Rept. of Inv.
6185, 1963, 11 pp.
63) _____. Limits of Flammability of Hydrazine-Hydrocarbon Vapor Mixtures. J. Chem.
Eng. Data, July 1962, pp. 375-376.
64) Gaydon, A. G., and H. G. Wolfhard. Flames, Their Structure, Radiation and
Temperature. Chapman &, Hall, Ltd. (London), 2d ed., 1960, 383 pp.
65) Gealer, Roy L., and Stuart W. Churchill. Detonation Characteristics of HydrogenOxygen Mixtures at High Initial Pressures. AIChE, v. 6, September 1960, pp. 501-505.
66) Gerstein, M. A Study of Alkylsilane Flames. 7th Symp. (Internat.) on Combustion.
Butterworths Sci. Pub. (London), 1959, pp. 903-905.
67) Gerstein, Melvin, Edward R. Carlson, and Francis U. Hill. Natural Gas-Air Explosions
at Reduced Pressure. Ind. and Eng. Chem., v. 46, 1954, pp. 2558-2562
68) Gibbs, G. J., and H. F. Calcote. Effect of Molecular Structure on Burning Velocity. J.
Chem. Eng. Data, v. 5, 1959, pp. 226-237.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
190
69) Glasstone, Samuel. Thermodynamics for Chemists. D. Van Nostrand Co., Inc., New
York, 1946, 522 pp.
70) Glendinning, W. G., and A. M. MacLennan. Suppression of Fuel-Air Explosions. Nat.
Fire Protect. Assoc. Quart., v. 45, July 1951, p. 61.
71) Gliwitzky, W. Prevention of Acetylene-Air Explosions by Addition of Carbon Dioxide
and Nitrogen. Autogene Metalbearbeit, v. 33, 1940, pp. 2-5.
72) Grabowski, G. J. Industrial Explosion Protection. J. Am. Oil Chem. Soc., v. 36, 1959,
pp. 57-59.
73) Gray, P., and J. C. Lee. Recent Studies of the Oxidation and Decomposition Flames
of Hydrazine. 7th Symp. (Internat.) on Combustion, Butterworths Sci. Pub. (London),
1959, p. 61.
74) Greenlee, Kenneth. Butadiene-Crotonaldehyde Explosion. Chem. and Eng. News,
v. 26, 1948, p. 1985.
--`,,```,,,,````-`-`,,`,,`,`,,`---
75) Guest, P. G., V. W. Sikora, and Bernard Lewis. Static Electricity in Hospital Operating
Suites: Direct and Related Hazards and Pertinent Remedies. BuMines Rept. of Inv.
4833, 1952, 64 pp.
76) Haber, F., and H. Wolff. Mist Explosions. Zeit. angew. Chem., v. 36, 1923, p. 373.
77) Hall, A. R., and R. A. M. Straker. The Methyl-acetylene (Propyne) Decomposition
Flame at Pressures of 10, 20 and 40 Atmospheres. Rocket Propulsion Establishment
(Westcott), TN 192, 1960, p. 11.
78) Hanna, N. E., M. G. Zabetakis, R. W. Van Dolah, and G. H. Damon. Potential Ignition
Hazards Associated With Compressed-Air Blasting Using a Compressor
Underground. BuMines Rept. of Inv. 5223, 1956, 33 pp.
79) Harris, D. N., Glenn Karel, and A. L. Ludwig. Electrostatic Discharges in Aircraft Fuel
Systems. 41st Ann. API Meeting Preprint, 1961, 10 pp.
80) Heck, W. B., Jr., and R. L. Johnson. Aluminum Alkyls. Ind. and Eng. Chem., v. 54,
December 1962, pp. 35-38.
81) Heimel, Sheldon, and Robert C. Weast. Effect of Initial Mixture Temperature on the
Burning Velocity of Benzene-Air, n-Heptane-Air, and Isooctane-Air Mixtures. 6th
Symp. (Internat.) on Combustion, Reinhold Publishing Corp., New York, 1957, pp.
296-302.
82) Herzog, R. E., E. C. Ballard, and H. A. Hartung. Evaluating Electrostatic Hazard
During the Loading of Tank Trucks. 41st Ann. API Meeting Preprint, 1961, 7 pp.
83) Hildebrand, Joel H., and Robert L. Scott. The Solubility of Nonelectrolytes. Reinhold
Pub. Corp., New York, 3d ed., 1950, p. 243.
84) Hill, Howard W. Methyl Bromide-Air Explosion, Chem. Eng. Prog., v. 58, August 1962,
pp. 46-49.
85) Holdsworth, M. P., J. L. vander Minne, and S. J. Vellenga. Electrostatic Charging
During the White Oil Loading of Tankers. 41st Ann. API Meeting Preprint, 1961, 30 pp.

Not for Resale
191
ANSI/ISA-TR12.13.01-1999 (R2005)
86) Holtz, John C., L. B. Berger, M. A. Elliott, and H. H. Schrenk. Diesel Engines
Underground. BuMines Rept. of Inv. 3508, 1940, 48 pp.
87) Hsieh, M. S., and D. T. A. Townsend. An Examination of the Mechanism by Which
"Cool" Flames May Give Rise to "Normal" Flames. Part I. The Inflammable Ranges
of Ether-Air Mixtures in Closed Vessels. J. Chem. Soc. (London), 1939, pp. 337-340.
88) _____. An Examination of the Mechanism by Which "Cool" Flames May Give Rise to
"Normal" Flames. Part II. The Inflammable Ranges of Higher Paraffin Hydrocarbons
in Air: The Establishment of "Cool" Flame Ranges at Ordinary Temperatures and High
Pressures. J. Chem. Soc. (London), 1939, pp. 341-345.
89) International Acetylene Association. Acetylene Transmission for Chemical Synthesis.
Internat. Acetylene Assoc., New York (no date), 40 pp.
90) Jackson, J. L., and R. S. Brokaw. Variation of Spontaneous Ignition Delays With
Temperature and Composition for Propane-Oxygen-Nitrogen Mixtures at
Atmospheric Pressure. Nat. Advisory Committee for Aeronautics Res. Memo.
E54B19. 1954, 29 pp.
91) Jacobs, R. B., W. L. Bulkley, J. C. Rhodes, and T.L. Speer. Destruction of a Large
Refining Unit by Gaseous Detonation. Chem. Eng. Prog., v. 53, December 1957, pp.
565-573.
92) Johnson, J. Enoch, John W. Crellin, and Homer W. Carhart. A Study of the Autoignition
Properties of Certain Diesel Fuels. Naval Res. Laboratory Rept. 3859, 1951, 29 pp.
93) _____. Ignition Studies. Part II. The Spontaneous Ignition Properties of Some Diesel
Fuels and Pure Hydrocarbons. NRL Rept. 4202, 1953, 14 pp.
--`,,```,,,,````-`-`,,`,,`,`,,`---
94) Jones, G. W. Fire and Explosion Hazards of Combustible Gases and Vapors. Ind.
Hygiene and Toxicology, ed. by Frank A. Patty. Intersci. Pub., Inc., New York, v. 1,
ch. 16, 2d rev. ed., 1958, pp. 511-548.
95) _____. Inflammation Limits and Their Practical Application in Hazardous Industrial
Operations. Chem. Rev., v. 22, February 1938, pp. 1-26.
96) _____. The Inflammability of Refrigerants. Ind. Eng. Chem., v. 20, 1928, pp. 367-370.
97) Jones, G. W., and B. B. Beattie. Explosive Properties of Divinyl Ether. Ind. and Eng.
Chem., v. 26, 1934, pp. 557-560.
98) Jones, G. W., E. S. Harris, and W. E. Miller. Explosive Properties of Acetone-Air
Mixtures. BuMines Tech. Paper 544, 1933, 26 pp.
99) Jones, G. W., R. E. Kennedy. Effect of Pressure on Ignition Temperature of Acetylene
and Acetylene-Air Mixtures. BuMines Rept. of Inv. 3809, 1945, 7 pp.
100) _____. Extinction of Ethylene Flames by Carbon Dioxide and Nitrogen. Anesthesia
and Analgesia, v. 9, 1930, pp. 6-10.
101) _____. Extinction of Propylene Flames by Diluting With Nitrogen and Carbon Dioxide
and Some Observations on the Explosive Properties of Propylene. BuMines Rept.
of Inv. 3395, 1938, 14 pp.

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
192
102) _____. Limits of Inflammability of Butadiene in Air. BuMines Rept. of Inv. 3565, 1941,
4 pp.
103) _____. Prevention of Butadiene-Air Explosions by Addition of Nitrogen and Carbon
Dioxide. BuMines Rept. of Inv. 3691, 1943, 11 pp.
104) Jones, G. W., R. E. Kennedy, and W. E. Miller. Limits of Inflammability and Ignition
Temperature of Ethyl Mercaptan in Air. BuMines Rept. of Inv. 3648, 1942, 6 pp.
105) Jones, G. W., R. E. Kennedy, and I. Spolan. Effect of High Pressures on the
Flammability of Natural Gas-Air-Nitrogen Mixtures. BuMines Rept. of Inv. 4557, 1949,
16 pp.
106) Jones, G. W., R. E. Kennedy, and G. J. Thomas. Explosion Hazards of Combustible
Anesthetics. BuMines Tech. Paper 653, 1943, 47 pp.
107) _____. Explosive Properties of Cyclopropane. BuMines Rept. of Inv. 3511, 1940,
17pp.
108) _____. Inflammability of Ether-Oxygen-Helium Mixtures. BuMines Rept. of Inv. 3589,
1941, 15pp.
109) Jones, E., and J. C. Kerr. Inflammability Limits of Ammonia, Nitrous Oxide, and Air.
J. Soc. Chem. Ind., v. 68, 1949, pp. 31-34.
110) Jones, G. W., and W. E. Miller. Ignition Temperatures of Acetylene-Air and AcetyleneOxygen Mixtures. BuMines Rept. of Inv. 3567, 1951, 5 pp.
112) Jones, G. W., and G. St. J. Perrott. Oxygen Required for the Propagation of Hydrogen,
Carbon Monoxide, and Methane Flames. Ind. and Eng. Chem., v. 19, 1927, pp. 985989.
113) Jones, G. W., and F. E. Scott. Extinction of Propane and Butane Flames by
Dichlorodifluoromethane. BuMines Rept. of Inv. 3908, 1946, 8 pp.
114) _____. Inflammability of Dimethyl Ether-Dichlorodifluoromethane-Air Mixtures.
115) Jones, G. W., W. P. Yant, W. E. Miller, and R. E. Kennedy. Limits of Inflammability of
Diethyl Ether and Ethylene in Air and Oxygen. BuMines Rept. of Inv. 3278, 1935, 5 pp.
116) _____. The Ignition Temperatures of Diethyl Ether and Ethylene in Air and Oxygen.
117) Jones, G. W., M. G. Zabetakis, and G. S. Scott. Elimination of Ethyl Mercaptan VaporAir Explosions in Stench Warning Systems. BuMines Rept. of Inv. 5090, 1954, 8 pp.
118) Jost, Wilhelm. Explosion and Combustion Processes in Gases. McGraw-Hill Book
Co., New York, 1946, 621 pp.
119) Kharasch, M. S. Heats of Combustion of Organic Compounds. NBS J. Res., v. 2,
1929, pp. 359-430.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
111) Jones, G. W., W. E. Miller, and H. Seaman. Explosive Properties of Methyl-FormateAir Mixtures. Ind. and Eng. Chem., v. 25, 1933, pp. 694-696.
193
ANSI/ISA-TR12.13.01-1999 (R2005)
120) Kennedy, R. E., G. S. Scott, and M. G. Zabetakis. Flammability Limits of Hydrocarbons

at High Temperatures and Pressures. Chem. Eng. Prog., v. 53, 1957, pp. 125-126.
121) Kennedy, R. E., I. Spolan, W. K. Mock, and G. S. Scott. Effect of High Pressures on
the Explosibility of Mixtures of Ethane, Air, and Carbon Dioxide and Ethane, Air, and
Nitrogen. BuMines Rept. of Inv. 4751, 1950, 11 pp.
122) Kennedy, R. E., I. Spolan, and G. S. Scott. Explosibility of Mixtures of Propane, Air,
and Carbon Dioxide and of Propane, Air, and Nitrogen at Elevated Pressures.
123) Klinkenberg, A., and J. L. vander Minne. Electrostatics in the Petroleum Industry.
Elsevier Publishing Co., New York, 1958, 191 pp.
124) Kobe, Kenneth A., and Ernest G. Long. Thermochemistry for the Petrochemical
Industry. Part VI. Acetylenes and Diolefins. Petrol. Refiner, v. 28, 1949, p. 133.
125) Kogarko, S. M. Detonation of Methane-Air Mixtures and the Detonation Limits of
Hydrocarbon-Air Mixtures in a Large-Diameter Pipe. Soviet Physics, Tech. Phys., v.
3, 1958, pp. 1904-1916. (Transl. of J. Tech. Phys., USSR, v. 28, pp. 2072-2078.)
126) Kuchta, Joseph M., Alphonse Bartkowiak, Irving Spolan, and Michael G. Zabetakis.
Flammability Characteristics of High-Temperature Hydrocarbon Fuels. Wright Air
Development Division Tech. Rept. 61-89, 1961, 29 pp.
127) Kuchta, Joseph M., Sotirios Lambiris, and Michael G. Zabetakis. Flammability and
Autoignition of Hydrocarbon Fuels Under Static and Dynamic Conditions. BuMines
Rept. of Inv. 5992, 1962, 21 pp.
128) Kunin, T. I., and V. I. Serdyukov. Limits and Temperatures of Explosion of HydrogenChlorine Mixtures in Hydrogen Chloride. J. Gen. Chem., USSR, v. 16, 1946, p. 14211430.
129) Le Chatelier, H., and O. Boudouard. Limits of Flammability of Gaseous Mixtures.
Bull. Soc. chim. (Paris), v. 19, 1898, pp. 483-488.
130) Lewis, Bernard, and Guenther von Elbe. Combustion, Flames and Explosions of
Gases. 2d ed. Academic Press, Inc., New York, 1961,731 pp.
131) Linnett, J. W. Methods of Measuring Burning Velocities. 4th Symp. (Internat.) on
Combustion. Williams & Wilkins Co., Baltimore, Md., 1953, pp. 20-35.
132) Linnett, J. W., and C. J. S. M. Simpson. Limits of Inflammability. 6th Symp. (Internat.)
on Combustion, Reinhold Pub. Corp., New York, 1957, pp. 20-27.
133) Lloyd, P. The Fuel Problem in Gas Turbines. Inst. Mech. Eng. Proc., War Emergency
Issue No. 41, v. 159, 1948, p. 220.
134) Lowenstein, J. G. Calculate Adequate Rupture Disk Size. Chem. Eng., v. 65, 1958,
pp. 157-158.
135) Luker, James A., and Leonard B. Adler. Effect of Reactor Length on the Formation
of Detonation in Saturated Knallgas-Steam Mixtures. J.Chem. Phys., v. 36, 1962,
pp. 718-721.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
194
136) Luker, James A., and Melvin J. Leibson. Dynamic Loading of Rupture Disks With
Detonation Waves. J. Chem. Eng. Data, v. 4, 1959, pp.133-135.
137) Luker, James A., Paul L. McGill, and Leonard B. Adler. Knallgas and Knallgas-Steam
Mixtures at High Initial Temperature and Pressure. J. Chem. Eng. Data, v. 4, 1959,
pp. 136-142.
138) Manton, J., and B. B. Milliken. Study of Pressure Dependence of Burning Velocity by
the Spherical Vessel Method. Gas Dynamics Symp. on Aerothermochem. Proc.,
1955, pp. 151-157.
139) Marsel, J., and L. Dramer. Spontaneous Ignition Properties of Metal Alkyls. 7th Symp.
(Internat.) on Combustion, Butterworths Sci. Pub. (London), 1959, p. 906.
141) Matson, A. F., and R. E. Dufour. Limits of Flammability of Methyl Ethyl Ketone Vapor
in Air at Initial Temperatures of 100, 150 and 200. Underwriters Laboratory Bull.
Res. 38, 1947, pp. 5-18.
142) McDonald, J. S., and J. E. Owens. Investigation of Tetralin Explosion. Atomics
Internat. Rept. NAA-SR-4803, Canoga Park, Calif., 1960, 58 pp.
143) Mellan, lbert. Industrial Solvents. 2d ed. Reinhold Pub. Corp., New York, 1950, 758
pp.
144) Miller, S. A., and E. Penny. Hazards in Handling Acetylene in Chemical Processes,
Particularly Under Pressure. Proc. Symp. on Chem. Process Hazards, Inst. of Chem.
Eng. (London), 1960, p. 87.
145) Missen, R. W. Pressure Drop in Vapor-Relief Systems. Chem. Eng., 1962, pp. 101102.
146) Moore, R. H. Fires and Explosions in Compressed Air Systems. Canadian Min. and
Met., Bull. No. 609, v. 56, 1963, pp. 18-19.
147) Moran, H. E., Jr., and A. W. Bertschy. Flammability Limits for Mixtures of Hydrocarbon
Fuels, Air, and Halogen Compounds. NRL Rept. 4121, 1953, 12 pp.
148) Moreton, D. H. Review of Synthetic Lubricants. Lubrication Eng., 1954, pp. 65-73.
149) Morgan, N. D. The Influence of Lubricants on Explosions in Compressed Air Systems.
Canadian Min. and Met. Bull. 609, v. 56, pp. 19-21.
150) Morrison, Richard Boyd. A Shock-Tube Investigation of Detonative Combustion.
Univ. of Michigan, UMM-97, 1955, 121 pp.
151) Moyle, Morton P., Richard B. Morrison, and Stuart W. Churchill. Detonation
Characteristics of Hydrogen-Oxygen Mixtures. AIChE, March 1960, pp. 92-96.
152) Mulcahy, M. F. R. Oxidation of Lower Paraffins. Disc. Faraday Soc., 1947, No. 2, pp.
128-132.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
140) Martindill, G. H., F. W. Lang, and M. G. Zabetakis. Flammability Characteristics of the

Vapor System Hydrogen Peroxide-Xylene-Formic Acid-Water. J. Chem. Eng. Data,
v. 5, 1960, pp. 355-358.
195
ANSI/ISA-TR12.13.01-1999 (R2005)
153) Mullins, B. P. Spontaneous Ignition of Liquid Fuels. Butterworths Sci. Pub. (London),
1955, 117 pp.
154) Mullins, B. P., and S. S. Penner. Explosions, Detonations, Flammability and Ignition.
Pergamon Press (London), 1959, 287 pp.
155) Murrin, R. W., and S. Goldhagen. Determination of the C-O Bond Energy From the
Heats of Combustion of Four Aliphatic Ethers. Naval Powder Factory NPF TR 75,
NAVord Report No. 5491, 1957, 14 pp.
156) National Advisory Committee for Aeronautics. Basic Considerations in the
Combustion of Hydrocarbon Fuels With Air. Rep't 1300, ed. by Henry C. Barnett and
Robert R. Hibbard, 1957, 259 pp.
157) National Board of Fire Underwriters. Fire and Explosion Hazards of Organic Peroxide.
Res. Rept. No. 11, 1956, 60 pp.
158) National Fire Protection Association. Fire-Hazard Properties of Flammable Liquids,
Gases and Volatile Solids. NFPA 325, 60 Battery march St., Boston 10, Mass., 1960,
126 pp.
159) Nuckolls, A. H. Underwriters' Laboratory Method for the Classification of the Hazards
of Liquids. National Board of Fire Underwriters, Chicago, Ill., 1929, 20 pp.
160) Ordnance Corps, U.S. Department of the Army. Ordnance Safety Manual. ORDM
7-224, 1951; Sec. 17, May 15, 1958, 68 pp.
161) Palmer, K. N. The Quenching of Flame by Perforated Sheeting and Block Flame
Arrestors. Proc. Symp. on Chemical Process Hazards, Inst. Chem. Eng. (London),
1960, p. 51.
162) _____. The Quenching of Flame by Wire Gauzes. 7th Symp. (Internat.) on
Combustion, Butterworths Sci. Pub. (London), 1959, pp. 497-503.
163) Parker, W. G., and H. G. Wolfhard. Properties of Diborane Flames. Fuel, v. 35, 1956,
pp. 323-331.
164) _____. Some Characteristics of Flames Supported by NO and NO2. 4th Symp.
(Internat.) on Combustion, Williams & Wilkins Co., Baltimore, Md.. 1953, pp. 420-428.
165) Penny, E. The Velocity of Detonation in Compressed Acetylene. Faraday Soc. Disc.,
No. 22, 1956, pp. 157-161.
166) Perlee, Henry E., Agnes C. Imhof, and Michael G. Zabetakis. Flammability
Characteristics of Hydrazine Fuels in Nitrogen Tetroxide Atmospheres. J. Chem.
Eng. Data, 1962, pp. 377-379.
167) Pieters, H. A. J., J. W. Hovers, and B. J. Rietveld. Determination of the Explosion
Limits of Gases. Fuel, v. 26, 1947, pp. 80-81.
168) Porter, R. L. Unusual Pressure Relief Devices. Ind. and Eng. Chem., v. 54, January
1962, pp. 24-27.
169) Price, Fraser P. First and Second Limits of Explosion of Diborane-Oxygen Mixtures.
J. Am. Chem. Soc., v. 72, 1950, pp. 5361-5365.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
196
170) Randall, P. N., J. Bland , W. M. Dudley, and R. B. Jacobs. Effects of Gaseous

Detonations Upon Vessels and Piping. J. Chem. Eng. Prog., v. 53, December 1957,
pp. 574-580.
171) Randall, P. N., and I. Ginsburgh. Bursting of Tubular Specimens by Gaseous
Detonation. ASME, Trans., Paper No. 60-WA-12, 1960, 9 pp.
172) Rasbash, D. J., and Z. W. Rogowski. Gaseous Explosions in Vented Ducts.
Combustion and Flame, v. 4, December 1960, pp. 301-312.
173) _____. Relief of Explosions in Duct Systems. Proc. Symp. on Chem. Process
Hazards, Inst. Chem. Eng. (London), 1960, p. 58.
175) Richardson, E. C., and C. R. Sutton. Explosive Properties of Lacquer-Solvent Vapors.

Ind. and Eng. Chem., v. 20, 1928, pp. 187-190.
176) Roberts, A., B. R. Pursall, and J. B. Sellers. Methane Layering in Mine Airways. Coll.
Guard., v. 205, October 1962, pp. 535-541.
177) _____. Methane Layering in Mine Airways. Part II, The Theory of Layering. Coll.
Guard., v. 205, 1962, pp. 588-593.
178) _____. Methane Layering in Mine Airways. Part III. The Theory of Layering
(Continued). Coll. Guard., v. 205, 1962, pp. 630-636.
179) _____. Methane Layering in Mine Airways. Part IV, Studying Layering Phenomena
in a Laboratory Model. Coll. Guard., v. 205, 1962, pp. 723-732.
180) Roberts, A., B. R. Pursall and J. B. Sellers. Methane Layering in Mine Airways. Part
V, Studying Layering Phenomena in a Laboratory Model. Coll. Guard., v. 205, 1962,
pp. 756-763.
181) Rogers, D. T., and C. E. Schleckser. Engineering and Theoretical Studies of Static
Electricity in Fuel. Proc. 5th World Petrol. Cong., New York, sec. 8, paper 10, 1959,
pp. 103-121.
182) Rolingson, W. R., John MacPherson, P. D. Montgomery, and B. L. Williams. Effect
of Temperature on the Upper Flammable Limit of Methane, Ammonia, and Air
Mixtures. J. Chem. Eng. Data, v. 5, 1960, pp. 349-351.
183) Rossini, F. D. and others. Selected Values of Properties of Hydrocarbons. NBS Circ.
C461, 1947, 483 pp.
184) Salooja, K. C. Studies of Combustion Processes Leading to Ignition in Hydrocarbons.
Combustion and Flame, v. 4, 1960, pp. 117-136.
185) Sargent, H. B. How to Design a Hazard-Free System to Handle Acetylene. Chem.
Eng., February 1957, pp. 250-254.
186) Schumb W. C., C. N. Satterfield, and R. L. Wentworth. Hydrogen Peroxide. Reinhold
Pub. Co., New York, 1955, 750 pp.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
174) Rebenstorf, Melvin A. Designing a High Pressure Laboratory. Ind. and Eng. Chem.,
v. 53, 1961, pp. 40A-42A.
197
ANSI/ISA-TR12.13.01-1999 (R2005)
187) Scott, D. A. Hazards With Butadiene and its Properties. Am. Chem. Soc., v. 18, 1940,
p. 404.
188) Scott, F. E., J. J. Burns, and B. Lewis. Explosive Properties of Hydrazine. BuMines
Rept. of Inv. 4460, 1949, 18 pp.
189) Scott, F. E., R. W. Van Dolah, and M. G. Zabetakis. The Flammability Characteristics
of the System H2-NO-N2O-Air. 6th Symp. (Internat.) on Combustion. Reinhold Pub.
Co., New York, 1957, pp. 540-545.
190) Scott, G. S. Flammability of Trichloroethylene. BuMines Rept. of Inv. 6190,1963, 5 pp.
191) Scott, G. S., G. W. Jones, and F. E. Scott. Determination of Ignition Temperatures of
Combustible Liquids and Gases. Modification of the Drop Method. Anal. Chem., v.
20, 1948, pp. 238-241.
192) Scott, George S., Henry E. Perlee, George H. Martindill, and Michael G. Zabetakis.
Review of Fire and Explosion Hazards of Flight Vehicle Combustibles. Aeronautical
Systems Division Tech. Rept. 61-278, supp. 1, 1962, 43 pp.
193) Semenov, N. N. Some Problems in Chemical Kinetics and Reactivity. Princeton Univ.
Press, Princeton, N.J., v. 2, 1959, 331 pp.
194) Setchkin, Nicholas P. Self-Ignition Temperatures of Combustible Liquids. J. Res.
NBS, v. 53, 1954, Res. Paper 2516, pp. 49-66.
195) Simmonds, W. A., and P. A. Cubbage. The Design of Explosion Reliefs for Industrial
Drying Ovens. Proc. Symp. on Chem. Process Hazards. Inst. Chem. Eng. (London),
1960, p. 69.
196) Simmons, R. F., and H. G. Wolfhard. The Influence of Methyl Bromide on Flames.
Trans. Faraday Soc., v. 51, 1955, p. 1211.
197) Simon, Dorothy M., Frank E. Belles, and Adolph E. Spakowski. Investigation and
Interpretation of the Flammability Region for Some Lean Hydrocarbon-Air Mixtures.
4th Symp. (Internat.) on Combustion, Williams & Wilkins Co., Baltimore, Md., 1953,
pp. 126-138.
198) Singer, J. M., Joseph Grumer, and E. B. Cook. Burning Velocities by the BunsenBurner Method. I. Hydrocarbon-Oxygen Mixtures at One Atmosphere.
II. Hydrocarbon-Air Mixtures at Subatmospheric Pressures. Proc. Aerothermochem.
Gas Dynamics Symp., 1955, pp. 139-150.
199) Smith, Marion L., and Karl W. Stinson. Fuels and Combustion. McGraw-Hill Book
Co., New York, 1952, 340 pp.
200) Solov'ev, N. V., and A. N. Baratov. Dependence of the Lower Limit of Flammability
on Molecular Structure. Russian J. Phys. Chem. (Zhur. Fiz. Khim.), v. 34, 1960, pp.
1661-1670.
201) Spakowski, A. E. Pressure Limit of Flame Propagation of Pure Hydrocarbon-Air
Mixtures at Reduced Pressures. Nat. Advisory Committee for Aeronautics Res.
Memo. E52H15, 1952, 33 pp.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
198
202) Spalding, D. B. Some Fundamentals of Combustion. Butterworths Sci. Pub. (London),

1955, 250 pp.
203) Stenberg, John F., and Edward G. Coffey. Designing a High-Pressure Laboratory.
Chem. Eng., 1962, pp. 115-118.
204) Stoner, R. G., and W. Bleakney. The Attenuation of Spherical Shock Waves in Air. J.
Appl. Phys., v. 19, 1948, pp. 670-678.
205) Sullivan, M. V., J. K. Wolfe, and W. A. Zisman. Flammability of the Higher-Boiling
Liquids and Their Mists. Ind. and Eng. Chem., v. 39, 1947, p. 1607.
206) Tamura, Z., and Y. Tanasawa. Evaporation and Combustion of Drop Contacting With
a Hot Surface. 7th Symp. (Internat.) on Combustion, Butterworths Sci. Pub. (London),
1959, pp. 509-522.
207) Terao, Kunio. Selbstzundung von Kohlenwasserstoff-Luftgemischen in Stosswellen.
J. Phys. Sec. of Japan, v. 15, 1960, pp. 2086-2092.
208) The Combustion Institute. Combustion and Flame. Butterworths Sci. Pub. (London),
v. 1-7, 1957-63.
209) _____. 4th Symposium (International) on Combustion. The Williams & Wilkins Co.,
Baltimore, Md., 1953, 926 pp.
210) _____. 5th Symposium (International) on Combustion. Reinhold Pub. Corp., New
York, 1955, 802 pp.
211) _____. 6th Symposium (International) on Combustion. Reinhold Pub. Corp., New
York, 1957, 943 pp.
212) _____. 7th Symposium (International) on Combustion. Butterworths Sci. Pub.
(London), 1959, 959 pp.
213) _____. 8th Symposium (International) on Combustion. The Williams & Wilkins Co.,
Baltimore, Md., 1962, 1164 pp.
214) The Institution of Chemical Engineers. Proceedings of the Symposium on Chemical
Process Hazards. Inst. Chem. Eng. (London), 1960, 117 pp.
215) Thomas, A. Flame Propagation Through Air-Fuel Foams. 6th Symp. (Internat.) on
216) Umland, A. W. Explosive Limits of Hydrogen-Chlorine Mixtures. J. Electrochem. Soc.,
v. 101, 1954, pp. 626-631.
217) U.S. Atomic Energy Commission. The Effects of Nuclear Weapons. Ed. by Samuel
Glasstone, April 1962, p. 163.
218) Van Dolah, Robert W., Michael G. Zabetakis, David S. Burgess, and George S. Scott.
Review of Fire and Explosion Hazards of Flight Vehicle Combustibles. BuMines Inf.
Circ. 8137, 1962, 80 pp.
219) Wayman, D. H., and R. L. Potter. Detonations in Gaseous Fuming Nitric AcidHydrocarbon Mixtures. Combustion and Flame, Butterworths Sci. Pub. (London),
1957, v. 1, pp. 321-329.
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
199
ANSI/ISA-TR12.13.01-1999 (R2005)
220) Weber, J. P., J. Savitt, and K. Kre. Detonation Tests Evaluate High Pressure Cells.
Ind. and Eng. Chem., v. 53, 1961, pp. 128A-131A.
221) Weil, N. A. Rupture Characteristics of Safety Diaphragms. J. Appl. Phys., 1959,
pp. 621-624.
222) White, A. G. Limits for the Propagation of Flame in Inflammable Gas-Air Mixtures. III.
The Effect of Temperature on the Limits. J. Chem. Soc., v. 127, 1925, pp. 672-684.
223) _____. Limits for the Propagation of Flame in Vapor-Air Mixtures. Part 1. Mixtures of
Air and One Vapour at the Ordinary Temperature and Pressure. J. Chem. Soc., v.
121, 1922, pp. 1244-1270.
224) _____. Limits for the Propagation of Flame in Inflammable Gas-Air Mixtures. Part 1.
Mixtures of Air and One Gas at the Ordinary Temperature and Pressure. J. Chem.
Soc., v. 125, 1924, pp. 2387-2396.
225) _____. Limits for the Propagation of Flame at Various Temperatures in Mixtures of
Ammonia With Air and Oxygen. J. Chem. Soc., v. 121, 1922, pp. 1688-1695.
226) White, A. G., and T. W. Price. The Ignition of Ether-Alcohol-Air and Acetone-Air
Mixtures in Contact With Heated Surfaces. J. Chem. Soc., v. 115. 1919,
pp. 1462-1505.
227) White, Douglas F. The Unintentional Ignition of Hydraulic Fluids Inside High Pressure
Pneumatic Systems. ASNE J., 1960, pp. 405-413.
229) Wolfson, Bernard T. Harnessing Explosions. Office of Aerospace Res. Rept. No. 17,
1962, pp. 3-4.
230) Wolfson, Bernard T., and Robert G. Dunn. Generalized Charts of Detonation
Parameters for Gaseous Mixtures. J. Chem. Eng. Data, v. 1, 1956, pp. 77-82.
231) Zabetakis, Michael G. Explosion of Dephlegmator at Cities Service Oil Company
Refinery, Ponca City, Okla., 1959. BuMines Rept. of Inv. 5645, 1960, 16 pp.
232) _____. Gasfreeing of Cargo Tanks. BuMines Inf. Circ. 7994, 1961, 10 pp.
233) Zabetakis, M. J., M. P. Benoy, and P. M. Gussey. Explosion Hazards of Diethyl Ether.
234) Zabetakis, M. G., and D. S. Burgess. Research on the Hazards Associated With the
Production and Handling of Liquid Hydrogen. BuMines Rept. of Inv. 5707, 1961, 50 pp.
235) Zabetakis, M. G., J. C. Cooper, and A. L. Furno. Flammability of Solvent Mixtures
Containing Methyl Ethyl Ketone and Tetrahydrofuran in Air. BuMines Rept. of Inv.
6048, 1962, 14 pp.
236) Zabetakis, M. G., and H. H. Engel. Flammable Materials: A Lecture Demonstration.
BuMines Inf. Circ. 8005, 1961, 17 pp.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
228) Winter, E. F. The Electrostatic Problem in Aircraft Fueling. J. Royal Aeronautical

Soc., v. 66, 1962, pp. 429-446.
ANSI/ISA-TR12.13.01-1999 (R2005)
200
237) Zabetakis, M. G., A. L. Furno, and G. W. Jones. Minimum Spontaneous Ignition

Temperatures of Combustibles in Air. Ind. and Eng. Chem., v. 46, 1954,
pp. 2173-2178.
238) Zabetakis, M. G., P. M. Gussey, and G. S. Scott. Limits of Flammability of Methyl Ethyl
Ketone and Methyl Isobutyl Ketone in Bromochloromethane-Air Mixtures. BuMines
Rept. of Inv. 5680 1960, 12 pp.
239) Zabetakis, M. G., and G. W. Jones. Flammability of Carbon Disulfide in Mixtures of
Air and Water Vapor. Ind. and Eng. Chem., v. 45, 1953, pp. 2079-2080.
240) _____. The Prevention of Industrial Gas Explosion Disasters. Chem. Eng. Prog., v.
51, 1955, pp. 411-414.
241) Zabetakis, Michael G., George W. Jones, George S. Scott, and Aldo L. Furno.
Research on the Flammability Characteristics of Aircraft Fuels. Wright Air
Development Center, Tech. Rept. 52-35, supp. 4, 1956, 85 pp.
242) Zabetakis, M. G., S. Lambiris, and G. S. Scott. Flame Temperatures of Limit Mixtures.
7th Symp. (Internat.) on Combustion, Butterworths Sci. Pub. (London), 1959,
pp. 484-487.
243) Zebatakis, M. G., C. M. Mason, and R. W. Van Dolah. The Safety Characteristics of
Normal Propyl Nitrate. BuMines Rept. of Inv. 6058, 1962, 26 pp.
244) Zabetakis, M. G., and J. K. Richmond. The Determination and Graphic Representation
of the Limits of Flammability of Complex Hydrocarbon Fuels at Low Temperatures
and Pressures 4th Symp. (Internat.) on Combustion, Williams & Wilkins Co.,
Baltimore, Md., 1953, pp. 121-126.
246) Zabetakis M. G., G. S. Scott, and G. W. Jones. Limits of Flammability of Paraffin

Hydrocarbons in Air. Ind. and Eng. Chem., v. 43, 1951, pp. 2120-2124.
247) _____. The Flammability Characteristics of the CnH2n-6 Aromatic Series. BuMines
Rept. of Inv. 4824, 1951, 9 pp.
248) Zabetakis, M. G., G. S. Scott, and R. E. Kennedy. Autoignition of Lubricants at
Elevated Pressures, BuMines Rept. of Inv. 6112, 1962, 10 pp.
249) Zeldovich, Ia. B., S. M. Kogarko, and N. N. Simonov. An Experimental Investigation
of Spherical Detonation of Gases. Zhurnal Tekh. Fiziki (J. Tech. Phys. (USSR)), v. 26,
1956, p. 1744.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
245) Zabetakis, M. G., and B. H. Rosen. Considerations Involved in Handling Kerosine.

Proc. Am. Petrol. Inst., sec. 3, v. 37, 1957, p. 296.
201
ANSI/ISA-TR12.13.01-1999 (R2005)
Appendix A
--`,,```,,,,````-`-`,,`,,`,`,,`---
Table A.1: Summary of limits of flammability, lower temperature limits (TL),

and minimum autoignition temperatures (AIT) of individual gases
and vapors in air at atmospheric pressure
Combustible
Limits of flammability
(volume-percent)
Acetaldehyde
1.6
10
4.0
60
Acetic acid
Acetic anhydride
Acetanilide
41.0
Acetone
AIT (C)
37
230
U25
L25
Acetal
TL (C)
5.4
2.7
2.6
10
175
40
465
47
390
545
13
465
Acetophenone
1.1
570
Acetylacetone
41.7
340
Acetyl chloride
390
5.0
Acetylene
2.5
100
305
Acrolein
2.8
31
235
Acrylonitrile
3.0
Acetone Cyanohydrin
2.2
6
12
Adipic acid
41.6
420
Aldol
250
Allyl alcohol
Allyl amine
2.0
2.5
18
2.2
22
Allyl bromide
42.7
Allyl chloride
2.9
o-Aminodiphenyl
Ammonia
.66
15
22
375
295
32
4.1
485
450
28
n-Amyl acetate
11.0
n-Amyl alcohol
11.4
tert-Amyl alcohol
n-Amyl chloride
51.6
tert-Amyl chloride
17.1
110
25
360
38
300
1.4
1.5
435
18.6
260
12
345
4.7
170
Amyl nitrite
41.0
210
n-Amyl propionate
41.0
380
n-Amyl ether

Not for Resale
Combustible
202
(volume-percent)
Amylene
Aniline
1.4
AIT (C)
n-Amyl nitrate
1.1
8.3
540
195
1
1.3
4
615
.65
Benzyl benzoate
275
1.2
Anthracene
Benzyl chloride
8.7
Benzene
TL (C)
U25
L25
7.9
560
.7
480
1.2
585
Bicyclohexyl
.65
Biphenyl
.70
2-Biphenylamine
.8
450
Bromobenzene
41.6
565
Butadiene(1,3)
2.0
n-Butane
1,3-Butandiol
5.1
74
245
110
540
12
1.8
8.4
420
72
41.9
405
395
Butene-1
1.6
Butene-2
1.7
9.7
325
n-Butyl acetate
51.4
18.0
425
n-Butyl alcohol
sec-Butyl alcohol
9.8
21
405
tert-Butyl alcohol
11.9
19.0
11
480
tert-Butyl amine
1.7
380
5.8
410
sec-Butyl benzene
10.77
15.8
420
tert-Butyl benzene
1.77
15.8
450
1.7
10
12
1.7
n-Butyl benzene
8.9
.82
n-Butyl bromide
12.5
Butyl cellosolve
81.1
385
265
1011
245
n-Butyl chloride
1.8
n-Butyl formate
1.7
n-Butyl stearate
4.3
355
2.1
450
10
8.2
Butyric acid
a-Butryolactone
82.0
Carbon disulfide
1.3
50
12.5
74
Carbon monoxide
Chlorobenzene
m-Cresol

1.4
81.1
Not for Resale
90
21
640
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
203
Combustible
ANSI/ISA-TR12.13.01-1999 (R2005)
(volume-percent)
TL (C)
AIT (C)
U25
L25
1116
Crotonaldehyde
2.1
Cumene
Cyanogen
6.6
Cycloheptane
1.1
6.7
Cyclohexane
1.3
7.8
Cyclohexanol
Cyclohexene
Cyclohexyl acetate
.88
6.5
425
245
1.2
300
1.2
1.0
335
Cyclopropane
2.4
10.4
500
Cymene
435
Decaborane
Decalin
n-Decane
.85
6.5
.2
1
.74
4.9
57
250
12
.75
13
5.6
46
210
Deuterium
4.9
75
Diborane
.8
88
Diesel fuel (60 cetane)
225
--`,,```,,,,````-`-`,,`,,`,`,,`---
Diethyl amine
1.8
Diethyl analine
.8
1,4-Diethyl benzene
.8
430
.75
240
Diethyl cyclohexane
10
80
36
630
Diethyl ether
1.9
3,3-Diethyl pentane
.7
290
Diethyl ketone
1.6
450
Dsobutyl carbinol
1.82
6.1
Dsobutyl ketone
1.79
16.2
2-4, Dsocyanate
120
Dsopropyl ether
1.4
Dimethyl amine
2.8
2,2-Dimethyl butane
1.2
2,3-Dimethyl butane
1.2
Dimethyl decalin
1.69
Dimethyl dichlorosilane
3.4
Dimethyl ether
n,n-Dimethyl formamide
2,3-Dimethyl pentane

160
7.9
400
7.0
7.0
95.3
235
3.4
27
350
11.8
114
1.1
Not for Resale
6.8
57
435
335
ANSI/ISA-TR12.13.01-1999 (R2005)
--`,,```,,,,````-`-`,,`,,`,`,,`---
Combustible
204
(volume-percent)
TL (C)
AIT (C)
U25
L25
2,2-Dimethyl propane
1.4
Dimethyl sulfide
2.2
7.5
450
20
Dimethyl sulfoxide
205
84
Dioxane
2.0
22
Dipentene
.75
Diphenylamine
.7
635
0.8
620
Diphenyl methane
485
Divinyl ether
1.7
n-Dodecane
Ethane
3.0
12.4
Ethyl acetate
2.2
11
Ethyl alcohol
3.3
Diphenyl ether
.7
74
205
130
515
11
19
365
3.5
1
1.0
3.8
Ethyl cyclobutane
1.2
14
2.0
237
27
.60
Ethyl chloride
Ethyl cyclohexane
45
Ethyl amine
Ethyl benzene
6.1
265
385
1
14
6.7
430
7.7
210
6.6
260
6.7
260
Ethyl cyclopentane
1.1
Ethyl formate
2.8
Ethyl lactate
1.5
Ethyl mercaptan
2.8
Ethyl nitrate
4.0
Ethyl nitrite
3.0
50
Ethyl propionate
1.8
11
Ethyl propyl ether
1.7
Ethylene
2.7
36
490
Ethyleneimine
3.6
46
320
Ethylene glycol
43.5
Ethylene oxide
Furfural alcohol
16
455
400
18
300
440
400
3.6
100
151.8
1616
72
390
Gasoline: 100/130
1.3
7.1
440
115/145
1.2
7.1
470
Glycerine
n-Heptane

370
1.05
Not for Resale
6.7
215
205
Combustible
(volume-percent)
4.43
n-Hexadecane
n-Hexane
1.2
7.4
126
205
26
225
1.2
4
Hydrazine
4.7
100
Hydrogen
4.0
75
Hydrogen cyanide
5.6
40
Hydrogen sulfide
4.0
44
.6
185
Isoamyl acetate
Isoamyl alcohol
1.1
7.0
1.4
lsobutane
1.8
1
8.4
1.7
Isobutyl benzene
10
Isobutyl formate
2.0
8.9
Isobutylene
1.8
9.6
Isopentan
1.4
Isophorone
.82
400
25
9.0
Isopropylacetate
AIT (C)
n-Hexyl ether
Isobutyl alcohol
TL (C)
U25
L25
n-Hexyl alcohol
ANSI/ISA-TR12.13.01-1999 (R2005)
350
81
6.0
430
465
460
1.7
2.2
Isopropyl biphenyl
4.6
Jet fuel: JP-4
1.3
440
8
240
JP-6
230
Kerosine
210
Methane
5.0
15.0
Methyl acetate
3.2
16
Methyl acetylene
1.7
Methyl alcohol
6.7
Methyl amine
44.2
Methyl bromide
10
3-Methyl butene-1
Methyl cellosolve
36
9.1
81.7
Methyl ethyl ether
42.2
Methyl chloride
47
--`,,```,,,,````-`-`,,`,,`,`,,`---
Not for Resale
385
15
18.0
2.5
540
430
1.5
17
187
11
51.2
Methyl cellosolve acetate

460
11
.84
Isopropyl alcohol
Methyl butyl ketone
360
20
380
46
Combustible
206
(volume-percent)
Methyl cyclohexane
Methyl cyclopentadiene
Methyl ethyl ketone
TL (C)
1.1
1
6.7
1.3
1.9
10
7.6
Methyl ethyl ketone peroxide

Methyl formate
5.0
Methyl cyclohexanol
Methyl isobutyl carbinol
Methyl isopropenyl ketone
Methyl lactate
1.8
445
40
390
465
295
40
5
9.0
2.2
4
.8
2, Methyl pentane
Methyl propionate
2.4
Methyl vinyl ether
49
23
1.2
41.2
Methyl styrene
250
1.0
a-Methyl naphthalene
Methyl propyl ketone
530
13
1.6
8.2
41.0
2.6
49
615
Monoisopropyl bicyclohexyl
Monomethylhydrazine
Naphthalene
10
.52
184.1
124
230
.53
18
141
435
3.2
4
19.88
205.9
526
Nicotine
Nitroethane
3.4
30
Nitromethane
7.3
33
1-Nitropropane
2.2
34
2-Nitropropane
495
39
Methylene chloride
2-Monoisopropyl biphenyl
AIT (C)
U25
L25
.75
2.5
27
n-Nonane
21.85
31
205
n-Octane
0.95
13
220
Paraldehyde
1.3
48
260
Pentaborane
.42
n-Pentane
1.4
7.8
Pentamethylene glycol
335
Phthalic anhydride
3-Picoline
41.4
Pinane
23.74
Propadiene

1.2
2.16
Not for Resale
22
9.2
140
570
500
237.2
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
207
Combustible
ANSI/ISA-TR12.13.01-1999 (R2005)
(volume-percent)
Propane
2.1
1,2-Propandiol
b-Propiolactone
9.5
450
2.9
17
n-Propyl acetate
1.8
12
Propyl amine
2.2
14
440
2.0
Propyl chloride
n-Propyl nitrate
17
2.4
Propylene
1.8
17
100
2.4
21
11
24
Propylene oxide
460
2.6
2.8
37
111.8
2512
Propargyl alcohol
Quinoline
2.4
1.0
Styrene
261.1
Sulfur
27
2.0
p-Terphenyl
n-Tetradecane
4.5
Tetrahydrofurane
2.0
Tetralin
2,2,3,3-Tetramethyl pentane
0.8
247
.96
535
200
.84
5.0
71
--`,,```,,,,````-`-`,,`,,`,`,,`---
390
11.2
Toluene
17.1
480
Trichloroethane
500
28
25
12
40
Triethyl amine
1.2
8.0
Triethylene glycol
8.9
289.2
2,2,3-Trimethyl butane
1.0
Trimethyl amine
2.0
2,2,4-Trimethyl pentane
.95
Trimethylene glycol
41.7
Trioxane
43.2
Turpentine

385
430
Tetramethylene glycol
Trichloroethylene
175
43.1
Propylene dichloride
Pyridine
102
410
2.9
Propylene glycol
AIT (C)
2.5
Propionaldehyde
n-Propyl alcohol
TL (C)
U25
L25
1.7
Not for Resale
30
420
420
12
415
400
208
(volume-percent)
Combustible
L25
AIT (C)
U25
Unsymmetrical dimethylhydrazine
2.0
Vinyl acetate
2.6
Vinyl chloride
TL (C)
3.6
95
33
m-Xylene
530
o-Xylene
465
p-Xylene
530
1.1
1.1
1.1
6.4
6.4
6.6
11
21
2t=47C
12t=53C
22t=195C
13
23
t=100C
t=75C
t=60C
t=43C
t=86C
t=160C
4Calculated
14t=130C
24t=96C
15
25
16
26
t=50C
t=85C
7
t=140C
8
t=150C
9t=110C
10
t=-175C

t=72C
t=117C
17
t=125C
18
t=200C
19t=78C
20
t=122C
t=70C
t=29C
27
t=247C
28
t=30C
29t=203C
Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-TR12.13.01-1999 (R2005)
209
Appendix B
ANSI/ISA-TR12.13.01-1999 (R2005)
Stoichiometric Composition
--`,,```,,,,````-`-`,,`,,`,`,,`---
The stoichiometric composition (Cst) of a combustible vapor CnHmOlFk in air may be obtained
from the equation
m k 2l
mk
C n H m O l F k + n + ------------------------- O 2 nCO 2 ------------- H 2 O + kHF .
2
4
Thus,
100
C st = ---------------------------------------------------------------m k 2l
1 + 4.773 n + -------------------------
4
volume-percent,
where 4.773 is the reciprocal of 0.2095, the molar concentration of oxygen in dry air. The
following table lists the values of Cst for a range of
k 2l
n + m
------------------------- values from 0.5 to 30.75:
N1
0.25
0.50
0.75
29.53
21.83
17.32
14.35
12.25
10.69
9.48
8.52
7.73
7.08
6.53
6.05
5.65
5.29
4.97
4.70
4.45
4.22
4.02
3.84
3.67
3.51
3.37
3.24
3.12
3.01
2.90
2.81
2.72
2.63
2.55
2.48
2.40
2.34
2.27
2.21
2.16
2.10
10
2.05
2.00
1.96
1.91
11
1.87
1.83
1.79
1.75
12
1.72
1.68
1.65
1.62
13
1.59
1.56
1.53
1.50
14
1.47
1.45
1.42
1.40
15
1.38
1.36
1.33
1.31
16
1.29
1.27
1.25
1.24

Not for Resale
ANSI/ISA-TR12.13.01-1999 (R2005)
210
N1
17
1.22
1.20
1.18
1.17
18
1.15
1.13
1.12
1.10
19
1.09
1.08
1.06
1.05
20
1.04
1.02
1.01
1.00
21
.99
.98
.97
.95
22
.94
.93
.92
.91
23
.90
.89
.88
.87
24
.87
.86
.85
.84
25
.83
.82
.81
.81
26
.80
.79
.78
.78
27
.77
.76
.76
.75
28
.74
.74
.73
.72
29
.72
.71
.71
.70
30
.69
.69
.68
.68
0.25
0.50
0.75
m k 2l
N = n + ------------------------- ; where n, m, l, and k are the number of carbon, hydrogen, oxygen, and halogen atoms, respectively, in
4
the combustible.
For example, the stoichiometric mixture composition of acetyl chloride (C2H3OCl) in air may be
found by noting that
312
m k 2l
N = n + ------------------------- = 2 + --------------------- = 2.0 .
4
4
The entry for N=2.0 in the preceding table is 9.48 volume-percent, which is the value of Cst for
this combustible in air.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
211
Appendix C
ANSI/ISA-TR12.13.01-1999 (R2005)
Heat Contents of Gases
T, K
298.16
CO2
H2O
O2
N2
300
.017
.014
.013
.013
400
.941
.823
.723
.709
500
1.986
1.653
1.4541
1.412
600
3.085
2.508
2.2094
2.125
700
4.244
3.389
2.9873
2.852
800
5.452
4.298
3.7849
3.595
900
6.700
5.238
4.5990
4.354
1,000
7.983
6.208
5.4265
5.129
1,100
9.293
7.208
6.265
5.917
1,200
10.630
8.238
7.114
6.717
1,300
11.987
9.297
7.970
7.529
1,400
13.360
10.382
8.834
8.349
1,500
14.749
11.494
9.705
9.178
1,600
16.150
12.627
10.582
10.014
1,700
17.563
13.785
11.464
10.857
1,800
18.985
14.962
12.353
11.705
1,900
20.416
16.157
13.248
12.559
2,000
21.855
17.372
14.148
13.417
2,100
23.301
18.600
15.053
14.278
2,200
24.753
19.843
15.965
15.144
2,300
26.210
21.101
16.881
16.012
2,400
27.672
22.371
17.803
16.884
2,500
29.140
23.652
18.731
17.758
Gordon, J. S. Thermodynamics of High Temperature Gas Mixtures and Application to Combustion Problems. WADC
Technical Report 57-33, January 1957, 172 pp.

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
(Kcal/mole1)
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
213
Appendix D
--`,,```,,,,````-`-`,,`,,`,`,,`---
Symbol:
A
A
a
B
Cst
DHc
K
k
L
L*
Lave
Lt
L/D
M
M1
NO2
n
P
Pm
DP
p
Su
T
t
U
Ut
V
V

ANSI/ISA-TR12.13.01-1999 (R2005)
Definitions of Principal Symbols
Definition
Constant.
Area.
Velocity of sound.
Constant.
Stoichiometric composition.
Heat of combustion.
Ratio of duct area to vent area.
Thermal conductivity.
Lower limit of flammability.
Modified lower limit value.
Average carbon chain length for paraffin
hydrocarbons and correlation parameter for
aromatic hydrocarbons.
Lower limit of flammability at tC.
Length to diameter ratio.
Molecular weight.
Mach number.
Equilibrium mixture of NO2 and N2O4 at a
specified temperature and pressure.
Number of moles.
Pressure.
Maximum pressure.
Pressure rise.
Partial pressure.
Burning velocity,
Absolute temperature.
Temperature.
Time delay before ignition.
Upper limit of flammability.
Upper limit of flammability at tC.
Volume.
Critical approach velocity.
Liquid regression rate.
Specific heat ratio.
Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---

Not for Resale
Developing and promulgating technically sound consensus standards, recommended practices, and
technical reports is one of ISAs primary goals. To achieve this goal, the Standards and Practices
Department relies on the technical expertise and efforts of volunteer committee members, chairmen,
and reviewers.
ISA is an American National Standards Institute (ANSI) accredited organization. ISA administers
United States Technical Advisory Groups (USTAGs) and provides secretariat support for
International Electrotechnical Commission (IEC) and International Organization for Standardization
(ISO) committees that develop process measurement and control standards. To obtain additional
information on the Societys standards program, please write:
ISA
Attn: Standards Department
67 Alexander Drive
P.O. Box 12277
Research Triangle Park, NC 27709
--`,,```,,,,````-`-`,,`,,`,`,,`---

ISBN 1-55617-697-X
Not for Resale

ANSI ISA TR12.13.01 R2005 - Flammability Characteristics of Combustible Gases and Vapors

Uploaded by

Copyright:

Available Formats

ANSI ISA TR12.13.01 R2005 - Flammability Characteristics of Combustible Gases and Vapors

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ANSI ISA TR12.13.01 R2005 - Flammability Characteristics of Combustible Gases and Vapors

Uploaded by

Copyright:

Available Formats

TECHNICAL REPORT

Reaffirmed 31 August 2005

Not for Resale

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

ADDITIONALLY, THE USE OF THIS STANDARD MAY INVOLVE HAZARDOUS MATERIALS,

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

Underwriters Laboratories Inc.

Factory Mutual Research Corporation

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

The Ohio State University

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

Detector Electronics Corporation

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

Syncrude Canada Ltd.

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

Copyright The Instrumentation, Systems, and Automation Society

This page intentionally left blank.

Not for Resale

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

This page intentionally left blank.

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

FLAMMABILITY CHARACTERISTICS OF COMBUSTIBLE

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

This publication has been cataloged as follows:

Zabetakis, Michael George, 1924-2005

U.S. Dept. of the Int. Library

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

FLAMMABILITY CHARACTERISTICS OF COMBUSTIBLE

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

Definitions and Theory

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

Figure 1Ignitibility Curve and Limits of Flammability for Methane-Air Mixtures at

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

Figure 2Effect of Temperature on Limits of Flammability of a Combustible Vapor

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

Copyright The Instrumentation, Systems, and Automation Society

Not for Resale

spontaneous-ignition, or autoignition, temperature (AIT) and is determined in a uniformly heated

Copyright The Instrumentation, Systems, and Automation Society