LGP4247 11SPL

11SP 4247 LCD TV Power specification
Rev 1.3
Specification
Date: 2012. 08. 15
Rev 1.3
1. INTRODUCTION
1.1 Scope
This approval is the description related to every electrical and structural specifications
and reliability For Power Supply Unit used on 4247 inch LGE LED TV.
1.2 Customers product related items
Product : Power Supply Unit
Part code : EAY62171601
1.3 Product name

Product name : LGP4247-11SPL
Revision code : 1.3
2. SPECIFICATION
2.1 Input Requirements
Nominal Input Voltage
AC 100V to AC 240V
Input Voltage Variation
AC 90V to AC 264V
Input Current
Under 3.5Arms . (at 100Vac & Nominal Load)

Under 1.5Arms . (at 240Vac & Nominal Load)
Nominal Frequency
50 / 60 Hz
Frequency Variation Range
47 Hz to 63 Hz
Phase
Single
Leakage Current
0.7mA_peak. (100Vac ~ 240Vac)
Surge Immunity
4kV / 1000ns / 0 to 360
Hold-up Time
More than 20ms at 100Vac and maximum output load
Lightning Surge
2kA Normal, Common Mode
Inrush Current
80A zero-peak max

at cold start and any specified line, load, temperature conditions.
2.1.1 Power Factor

over than 0.9 at 90 264Vac & max load condition
Date: 2012. 08. 15
Rev 1.3
2.2 Power Output Characteristics
Output
Voltage
Variable range
[V]
Rated Current
(Min, Max)
[Amean]
Voltage
Regulation
[V]
Ripple
Voltage
[mVp_p]
2 (0.001~2) (ON condition)
5%
250 mVp_p
0.09W Under(6mA)
3.5V
(STBY)
3.325V ~ 3.675V
12V
11.4V ~ 12.6V
3 (0.3~3
5%
350 mVp_p
24V
22.8V ~ 25.2V
4.1 (0.1~4.1)
5%
500 mVp_p
* On Condition : In a moment of Power_ON Signal activated, the current of 3.5V output should be
limited within 40mA(Max) at LCD TV condition for stability.
Do not turn Power_ON Signal on at the load condition of 3.5V output, more than 40mA.
* Total regulation for each output circuit includes the results of input voltage variation,
load variation, warm-up drift and temperature change.
* The following instruments shall be used for measuring ripple noise.
1. Probe having impedance ratio of 1:1.
2. Oscilloscope having frequency characteristic of 100MHz or more.
- Test Point : power output each pin
Add Electrolytic Capacitor 47 + 0.1
Power Supply Unit

Output Voltage
700mm
Load
Oscilloscope
Measurement point
Ripple and noise are measured at the end of output cable which are added a 0.1uF ceramic
capacitor and 47uF electrolytic capacitor. ( connected parallel )
* Power turn on system (Only E/Load condition)

If Main Board is opened, that is electrical load condition,
drive on signal must be turn on after about 1.5s behind power on signal
Date: 2012. 08. 15
Rev 1.3
2.2.1 Stand By Power Consumption

Output Voltage
3.5V (STBY)
Load [A]
12V
0.006
Wattage [W]
24V
Dont Care (Power-Off)
Less than 0.09Under (230Vac / 50Hz)
2.3 Environment Requirement

Operating Temperature Range
-10 to 40
(60:No Hardware Failure, TV SET Condition)
Operating Humidity Range
30 to 85 %
Storage Temperature Range
-25 to 85 deg.
Storage humidity Range
5 to 90 %
MTBF
(Mean Time Between Failure)
50,000 hour
Cooling Condition
Shock
Natural Air
98
Shock test consists of pivoting the power supply, from
one edge of its bottom side, on a flat surface
(such as wood having thickness of 10mm or more) and
allowing the opposite edge to fall from a height of 50mm
to this surface.
The test is performed three times on each edge of the
bottom side of the power supply
2.4 Dielectric Strength Voltage and Insulation Resistance
Safety
Dielectric
Strength Voltage
AC-DC 1.5K VAC 3 SEC 10 mA.

Between Primary and All Secondary Circuits.
Insulation
Resistance
Insulation resistance shall be more than 8M ohm (at DC 500V)

Between Primary Live, Neutral line and Secondary.
* Above tests are performed at room temperature in non-condensing atmospheric

conditions
* Frame grounds are connected to secondary circuits.
2.5 Burn-in
More than 0.5 hours at 45(5), Normal input voltage.
AC on/off must be test 1 time after burn-in.
80% Load of specification.
9
Date: 2012. 08. 15
Rev 1.3
2.6 Interface
Appellation
Explanation
POWER ON
2.7 Product Safety
Signal Direction
Vcc Circuit ON/OFF
Action
Hi : Vcc ON
Low : Vcc OFF
Input
Safety
Safety Standards to be applied
Design to meet the requirements as follows

UL60950, IEC60950, IEC60065 and 60950
EMI/RFI Standards to be applied
Design to meet the requirements as follows

FCC and EN55020, EN55013 Class B
with 4dB minimum margin.
2.8 Construction
Weight
Less than 1.0kg
Unit Size
290(W) X 240(D) X 12.9(H)
2.9 Function of protection

Protection
Over Current
Short Circuit
Trip point
Output Circuit
Notes
Min
Max
STBY 3.5V
3.0A
6.0A
Auto Re-start
12V
8.0A
28.4A
Latch
24V
5.0A
14.2A
Latch
STBY 3.5V
Auto Re-start
12V
Latch
24V
Latch
* This Power Supply has above-mentioned protections.

* Short circuit protection between different output terminals is not considered.
* Trip point for over voltage indicates the operating point when the output voltage
slowly increases.
* The conditions of Over Current measurement
Multi output(3.5V,12V,24V) is nominal load state except an over current
measurement.
10
Date: 2012. 08. 15
Rev 1.3
2.10 Sound Noise Characteristics.

PSU Noise Specification
22.5 dB(a) / 20.u Pa 2.0E-5 Pa
(1/1 octave, A-weighting, to 1khz ~ 16khz Total overall
Measure Location : Anechoic Room
Measure Condition : At a distance of 60cm mic
Full white pattern, at AC 110V/220V
The max specification
(measure 3 points, at PSU center and left & right on the side)
11
Date: 2012. 08. 15
Rev 1.3
2.11 Connector Specification

2.11.1 Connectors Usage
P201
P202
Type : SMAW200-H24S2
Maker : YEON-HO
Type : 20010WR-H14B/C
Maker : YEON-HO
Pin No.
Signal
Pin No.
Signal
Pin No.
Signal
POWER-ON
24V
24V
24V
24V
24V
GND
GND
24V
GND
GND
24V
3.5V
10
3.5V
24V
11
3.5V
12
3.5V
GND
13
GND
14
GND
GND
15
GND
16
N.C
GND
17
12V
18
INV ON/OFF
GND
19
12V
20
A-DIM
10
GND
21
12V
22
P-DIM
11
ERROR
23
N.C
24
ERROR
12
INV ON/OFF
13
A-DIM
14
P-DIM
SK100
Type : 90011WR-H03D
Maker : YEON-HO
Pin No.
Signal
LIVE
F.G
NEUTRAL
12
Date: 2012. 08. 15
Rev 1.3
2.12 PCB Dimension.
4.5mm
240
4.5mm
4.5mm
290
4.5mm
9.0mm
(Tolerance 0.5mm)
PCB : 1.6mm
SMD Holder : 2.5mm (Tolerance 0.4mm)
Lead cutting : 2.3mm
(Except T101, L601 Body : 2.3mm+0.5mm , GH : 2.5mm +0.5mm)
13
Date: 2012. 08. 15
Rev 1.3
2.13 Apply to the Eyelet point.(LGP4247-11SPL)

Apply to the Eyelet point 2.0 : EL1,EL2,EL9,EL10,EL19,EL20,EL29,EL30,EL35,EL36,EL37,EL38,EL53,EL54,EL55,EL56,EL61 (17EA)
Apply to the small Eyelet point 1.6 : EL3,EL4,EL5,EL6,EL7,EL8,EL11,EL12,EL15,EL16,EL17,EL18,EL21,EL22,EL31,EL32,EL33,EL34,
EL39,EL40,EL41,EL42,EL45,EL46,EL47,EL48,EL49,EL50,EL51,EL52,EL58,EL59 (32EA)
14
Date: 2012. 08. 15
Rev 1.3
2.14 Electrical Characteristics
No.
Test Item
Test method
Intermittent
Operation stability
Test
The switching regulator shall ON/OFF for 20,000 time at an

Interval of 10 sec at maximum load, after that electrical
Characteristics shall be satisfied.
Low temperature
operation
The switching regulator is left at the operating guarantee

Minimum temperature for 2 hours without applying electricity.
After that power shall be turned on, and then the electrical
Characteristics shall be satisfied.
Low temperature
Storage test Leave
At low temperature
The switching regulator is left at minimum storage

Temperature for 96 hours or more.
Then the switching regulator is left at a room temperature and
humidity for 1 hour or more, after that electrical characteristics
shall be satisfied.
The switching regulator is 10 consecutive temperature cycle that

shown below is performed and then leave them at room
temperature and humidity for 1 hour or more.
After that, electrical characteristics shall be satisfied.
Time
Heat cycle storage

test
Heat shock test
Temperature
30 minutes
25
30 minutes
25 -> -20
60 minutes
Minimum storage temperature (-20)
30 minutes
-20 -> 25
30 minutes
25
30 minutes
25 -> 70
60 minutes
Maximum storage temperature (70)
30 minutes
70 -> 25
Heat shock test performed under following conditions without

applying electricity and then leave them at room temperature and
humidity for 1 hour or more.
After that, electrical characteristics shall be satisfied.
Condition : -45(30minutes), 120(30minutes),
Switching time : Less than 5 minutes, 200 cycles.
15
Date: 2012. 08. 15
Rev 1.3
2.15 Mechanical Characteristics
No.
Test Item
Test method
Appearance
There shall be no contaminant or dirt on the switching regulator

which has adverse effect on electrical characteristics.
There shall be no excessive unevenness or scratches on the
plated or painted surface.
While applying electricity :
Vibration frequency : 5 ~ 100Hz
Acceleration : 4.9 m/s2
Vibration in X,Y,Z direction for 30 minutes
Vibration
While applying electricity :

Vibration frequency : 5 ~ 100Hz
Acceleration : 14.7 m/s2
Vibration in X,Y,Z direction for 30 minutes
After that electrical characteristics shall be satisfied.
There shall be no damage to appearance and construction.
Shock : 98 m/s2
Shock
On the oak more than 10mm thickness with the flat face, raise
the one side for 50mm, and it carries out each side free fail for
three sides.
There shall be no damage to appearance and construction.
16
Date: 2012. 08. 15

LGP4247 11SPL

Uploaded by

Copyright:

Available Formats

LGP4247 11SPL

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LGP4247 11SPL

Uploaded by

Copyright:

Available Formats

11SP 4247 LCD TV Power specification

Date: 2012. 08. 15

11SP 4247 LCD TV Power specification

1.3 Product name

Nominal Input Voltage

Input Voltage Variation

Under 3.5Arms . (at 100Vac & Nominal Load)

Frequency Variation Range

0.7mA_peak. (100Vac ~ 240Vac)

4kV / 1000ns / 0 to 360

More than 20ms at 100Vac and maximum output load

2kA Normal, Common Mode

80A zero-peak max

2.1.1 Power Factor

Date: 2012. 08. 15

11SP 4247 LCD TV Power specification

2.2 Power Output Characteristics

2 (0.001~2) (ON condition)

Power Supply Unit

* Power turn on system (Only E/Load condition)

Date: 2012. 08. 15

11SP 4247 LCD TV Power specification

2.2.1 Stand By Power Consumption

Less than 0.09Under (230Vac / 50Hz)

2.3 Environment Requirement

Operating Humidity Range

Storage Temperature Range

Storage humidity Range

2.4 Dielectric Strength Voltage and Insulation Resistance

AC-DC 1.5K VAC 3 SEC 10 mA.

Insulation resistance shall be more than 8M ohm (at DC 500V)

* Above tests are performed at room temperature in non-condensing atmospheric

Date: 2012. 08. 15

11SP 4247 LCD TV Power specification

2.7 Product Safety

Vcc Circuit ON/OFF

Safety Standards to be applied

Design to meet the requirements as follows

EMI/RFI Standards to be applied

Design to meet the requirements as follows

Less than 1.0kg

290(W) X 240(D) X 12.9(H)

2.9 Function of protection

* This Power Supply has above-mentioned protections.

Date: 2012. 08. 15

11SP 4247 LCD TV Power specification

2.10 Sound Noise Characteristics.

Date: 2012. 08. 15

11SP 4247 LCD TV Power specification

2.11 Connector Specification

Date: 2012. 08. 15

11SP 4247 LCD TV Power specification

2.12 PCB Dimension.

Date: 2012. 08. 15

11SP 4247 LCD TV Power specification

2.13 Apply to the Eyelet point.(LGP4247-11SPL)

Date: 2012. 08. 15

11SP 4247 LCD TV Power specification