Mom690 CB Analyzer

MOM690
Microhmmeter
A Megger Group Company
M O M 690
MOM690
Microhmmeter
Measuring resistance is an important part of maintaining high-voltage breakers and disconnecting switches.
Instruments that measure the resistance of high-current contacts and other transmission elements have been
included in the Programma line of products for many years.
MOM690 supplements our family of microhmmeters. In addition to high current capacity, MOM690 features
microprocessor-based measurement, storage and reporting. The built-in software enables you to carry out an
individual test or an entire series of tests and store the results.
With the optional MOMWin software you can also export the test results to a PC for further analysis and
reporting. Ranges are set automatically, resistances are measured continually and test results can be automatically
captured at a preset test current. What could be simpler?
After testing a breaker with a CT mounted in its current circuit, e.g. dead tank and GIS breakers, some standards
recommended that the CT is demagnetized. This troublesome task can be accomplished quickly and easily thanks to
the MOM690's AC output. The AC output can also be used as a general multi-purpose current source in different
applications.
Optional accessories
IMPORTANT!
PC Software MOMWin
Read the Users manual before using the instrument.
Measuring the resistance of a breaker

1. Make certain the line is de-energized on both sides of the
breaker.
2. Ground the breaker on one side and make certain it is closed.
3. Ground the microhmmeter.
4. Make certain the microhmmeter's ON/OFF switch is OFF while
making connections.
5. Connect the current cables to the DC+ and COM terminals and
the sensing cables to the sensing inputs to both sides of the
breaker, making sure that the polarities match properly.
IMPORTANT: The sensing cables must be connected inside the
current cables. Otherwise the test data will be incorrect. See Fig.
An optional Windows program named MOMWin is available for

MOM690. It can be used to control measurement, analyse the results
and report the results from a PC. It also enables you to retrieve test
results stored previously in MOM690.
All readings are saved in ASCII-format and can be easily exported to
your favourite spreadsheet program. Results can be presented in table
or diagram form in MOMWin.
The program runs in Windows 95, 98, NT, 2000 or XP. Minimum
requirement is a 486 computer with 8 MB of RAM.
Incl. serial cable for RS-232 port.
Cable set 15 m (49 ft)

2 x 15 m (49 ft), 95 mm2 (current cables).
6. Switch on the MOM690.
2 x 15 m (49 ft), 2.5 mm2 (sensing cables).
7. Select "AUTO" or "MAN" with the <FUNC>-button.
Weight: 29.4 kg (64.8 lbs)
8. Set output current to zero to start the measurement.

9. Increase the current to the desired value (600 A for example).
Cable extension sets
Measuring resistance at busbar joints
Since all current cables have bayonet connectors, standard cables can
be easily prolonged with 5- or 10-metre extension sets if so desired.
In situations requiring high currents and long cable lengths, heavier
cable sets may be necessary however.
1. Make certain the line is de-energized and the test object is

grounded.
Extension cable set No. 1
2. Ground the microhmmeter.
3. Make certain the microhmmeter's ON/OFF switch is OFF while

making connections.
4. Connect the microhmmeter's current cables to the test object. Do

not connect the sensing cables. Measurement will be done manually using an external portable voltmeter.
10. Read the resistance value.
5. Switch on the MOM690.

6. Select "MAN" with the <FUNC>-button.
7. Set output current to zero to start the measurement.
8. Increase the current to the desired value (100 A for example).
9. Using an external voltmeter, measure the voltage drop across
each contact element within every section of the busbar being
tested. The voltmeter must be set to DC.
10. Calculate the actual resistance.
Example: If the voltage drop is 0.0067 V at a current of 100 A, the
resistance will be 0.0067/100 , i.e. 67 .
Measuring the resistance of a breaker
Weight: 7.5 kg (16.5 lbs)

Weight: 15 kg (33 lbs)
Calibration shunt
An optional calibration shunt (600 A/60 mV) can be ordered for
MOM690, that enables you to make certain that the instrument
readings remain correct.
Transport case XL
With space for the standard 5 m cable set + extension cable set No. 1
or No. 2.
Measuring resistance at busbar joints
M O M 690
Application example
M O M 690
Specifications MOM690
Max. load resistance / current, 230 V model
Specifications are valid at nominal input voltage and an ambient

temperature of +25C, (77F). Specifications are subject to change
without notice.
Environment
Application field
Temperature
Operating
Storage & transport
Humidity
The instrument is intended for use in

high-voltage substations and industrial
environments.
0C to +50C (32F to +122F)
-40C to +70C (-40F to +158F)
5% 95% RH, non-condensing
Low Voltage Directive 73/23/ EEC am. by
93/68/EEC
EMC Directive 89/336/EEC am. by
91/263/EEC, 92/31/EEC and 93/68/EEC
EMC
General
Mains voltage
Power consumption
(max)
Protection
115/230 V AC, 50/60 Hz

115 V, 5980 VA (at 600 A output)
230 V, 9660 VA
Miniature circuit breaker, thermal fuse,
software
Measurement section
Ammeter
At 300 A
Max. current
10 m
575 A
Voltage (V)
0
50
100
200
300
400
500
5751)
600
700
8002)
7.3
6.9
6.4
5.5
4.8
3.9
3.0
2.5
2.2
1.5
0.9
Max. load time Input current

(A)
0.8
30 min.
10 min.
10
90 s
19
50 s
30 s
38
15 s
10 s
8s
52
5s
Output AC (CAT I), 115 V model

Current (A)
0
660
Voltage (V)
8.7
3.5
Max. load time Rest time

Cont.
2s
4 min.
Note: The DC and AC outputs must not be loaded at the same time.
Output DC (CAT I), 230 V model

Current (A)
0
50
100
200
300
400
500
600
700
7501)
8002)
Current
(A)
0
660
Voltage (V ) Max. load time Input current

(A)
9.4
0.4
9.0
30 min.
8.6
10 min.
6
8.0
90 s
7.2
50 s
6.4
40 s
5.7
30 s
5.0
15 s
33
4.3
8s
3.8
5s
3.6
42
Voltage
(V AC)
11.2
4.5
Max. load time Rest time

Cont.
2s
Note: The DC and AC outputs must not be loaded at the same time.
Standard 2 x 15 m 95mm
+ Ext. 1
3 m
360 A
Current (A)
Output AC (CAT I), 230 V model
0 200 m, > 200 m not specified

1
100 800 A, 1% of reading + 1 digit
50 99 A, (2% of reading + 2 digits)
0 49 A, not specified
Standard +
Ext. 1
6 m
420 A
480 A
18 m
1.8 m
690 A
Note: The above figures shows maximum load time from cold state 25C. They are not valid
for repeated tests
Max. load resistance / current, 115 V model

Standard
570 A
2 x 15 m 95mm
1) Maximum current with standard cables 2 x 5 m 50 mm

2) At 800 A and above, instant shut off
0 800 A
1A
100 800 A, 1% of reading + 1 digit
50 99 A, (2% of reading + 2 digits)
0 49 A, not specified
Resistance
Cable set
18 m
3.0 m
750 A
Stadard
+ Ext. 1
11 m
Note: The above figures shows maximum load time from cold state 25C. They are not valid
for repeated tests
350 x 270 x 220 mm

(13.8 x 10.6 x 8.7)
Transport case
610 x 290 x 360 mm
(24.0 x 11.4 x 14.2)
Weight, 115 V
24 kg (52.9 lbs)
model
38.9 kg (85.7 lbs) with accessories and
transport case
Weight, 230 V
23.7 kg (52.2 lbs)
model
38.6 kg (85.1 lbs) with accessories and
transport case
Available languages English, French, German, Spanish, Swedish
Current cables
2 x 5 m (16 ft), 50 mm
Sensing cables
2 x 5 m (16 ft), 2.5 mm
Optional current cable sets
Ext.1
Extension 2 x 5 m, 50 mm
Ext.2
Extension 2 x 10 m, 50 mm
2 x 15 m (49.2 ft) 95 mm
Range
Resolution
Inaccuracy
At 300 A
At 600 A
Max. current
Stadard
+ Ext. 1
14 m
1) Maximum current with standard cables 2 x 5 m 50 mm

2) At 800 A and above, instant shut off
Dimensions
Instrument
Range
Resolution
Inaccuracy
Standard
Output DC (CAT I), 115 V model
CE-marking
LVD
Cable set
10 m
540 A
4 min.
Grounding terminal
Connection for mains voltage
Miniature circuit breaker for mains
Switch for mains voltage
Variable transformer
AC current output
Common output terminal
DC current output
Voltage measurement input
Display
Setting selector
Function selector
Interrupts current and toggles the display

between resistance and voltage
RS 232 Serial interface
M O M 690
Information about current generation or memory location.

Value of the generated current.
Indicates whether the current is above (<)
or below (>) a preselected value.
Selected test current for Auto/DC Off.
Scroll using the <>- button.
Selected function. Scroll using the <FUNC>-button.
Shows the measured resistance or voltage value. Toggle by pressing the <>-button.
Ordering information
Art.No.
Complete with:
Cable set standard GA-05055
Ground cable GA-00200
Transport case GD-00182
115 V Mains voltage
230 V Mains voltage
BB-41190
BB-42390
MOM690
Optional accessories
Cable set and current shunt
PC Software MOMWin
Incl. serial cable for RS-232 port
Cable set 15 m (49 ft)
Calibration shunt
Transport case XL
BB-8010X
GA-09155
GA-05057
GA-05107
BB-90024
GD-00042
NOTICE OF COPYRIGHT & PROPRIETARY RIGHTS

2008, Programma Electric AB. All rights reserved.
The contents of this document are the property of Programma Electric AB. No part of this work may be reproduced or transmitted in any form or by any
means, except as permitted in written license agreement with Programma Electric AB.
Programma Electric AB has made every reasonable attempt to ensure the completeness and accuracy of this document. However, the information
contained in this document is subject to change without notice, and does not represent a commitment on the part of Programma Electric AB.
TRADEMARK NOTICES
Megger and Programma are trademarks registered in the U.S. and other countries.
All other brand and product names mentioned in this document are trademarks or registered trademarks of their respective companies.
Programma Electric AB is certified according to ISO 9001 and 14001.
Programma Electric AB
Eldarvgen 4
Box 2970
SE-187 29 TBY
Sweden
T +46 8 510 195 00

F +46 8 510 195 95
[email protected]
www.programma.se
Subject to change without notice. Art. No. ZI-BB04E Doc. BB0214CE
2008

Mom690 CB Analyzer

Uploaded by

Copyright:

Available Formats

Mom690 CB Analyzer

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mom690 CB Analyzer

Uploaded by

Copyright:

Available Formats

MOM690

A Megger Group Company

Read the Users manual before using the instrument.

Measuring the resistance of a breaker

An optional Windows program named MOMWin is available for

Cable set 15 m (49 ft)

6. Switch on the MOM690.

2 x 15 m (49 ft), 2.5 mm2 (sensing cables).

7. Select "AUTO" or "MAN" with the <FUNC>-button.

Weight: 29.4 kg (64.8 lbs)

8. Set output current to zero to start the measurement.

Cable extension sets

Measuring resistance at busbar joints

1. Make certain the line is de-energized and the test object is

Extension cable set No. 1

2. Ground the microhmmeter.

2 x 5 m (16 ft), 50 mm2 (current cables).

3. Make certain the microhmmeter's ON/OFF switch is OFF while

2 x 10 m (33 ft), 2.5 mm2 (sensing cables).

4. Connect the microhmmeter's current cables to the test object. Do

Extension cable set No. 2

10. Read the resistance value.

5. Switch on the MOM690.

Measuring the resistance of a breaker

Weight: 7.5 kg (16.5 lbs)

2 x 10 m (33 ft), 50 mm2 (current cables).

Measuring resistance at busbar joints

Max. load resistance / current, 230 V model

Specifications are valid at nominal input voltage and an ambient

The instrument is intended for use in

115/230 V AC, 50/60 Hz

Max. load time Input current

Output AC (CAT I), 115 V model

Max. load time Rest time

Output DC (CAT I), 230 V model

Voltage (V ) Max. load time Input current

Max. load time Rest time

Output AC (CAT I), 230 V model

0 200 m, > 200 m not specified

Max. load resistance / current, 115 V model

1) Maximum current with standard cables 2 x 5 m 50 mm

350 x 270 x 220 mm

1) Maximum current with standard cables 2 x 5 m 50 mm

Output DC (CAT I), 115 V model

Connection for mains voltage

Miniature circuit breaker for mains

Switch for mains voltage

Common output terminal

Voltage measurement input

Interrupts current and toggles the display

RS 232 Serial interface

Information about current generation or memory location.

Cable set and current shunt

NOTICE OF COPYRIGHT & PROPRIETARY RIGHTS

T +46 8 510 195 00

Subject to change without notice. Art. No. ZI-BB04E Doc. BB0214CE

You might also like