C0110 00

Designation: C 110 00
Standard Test Methods for
Physical Testing of Quicklime, Hydrated Lime, and

Limestone1
This standard is issued under the fixed designation C 110; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
C 25 Test Methods for Chemical Analysis of Limestone,

Quicklime, and Hydrated Lime3
C 28 Specification for Gypsum Plasters3
C 50 Practice for Sampling, Inspection, Packing, and Marking of Lime and Limestone Products3
C 51 Terminology Relating to Lime and Limestone (as used
by the Industry)3
C 91 Specification for Masonry Cement3
C 109 Test Method for Compressive Strength of Hydraulic
Cement Mortars (Using 2-in. or 50-mm Cube Specimens)3
C 117 Test Method for Material Finer than 75Micrometre
(No. 200) Sieve in Mineral Aggregates by Washing4
C 136 Test Method for Sieve Anlaysis of Fine and Coarse
Aggrgates4
C 150 Specification for Portland Cement3
C 185 Test Method for Air Content of Hydraulic Cement
Mortar3
C 188 Test Method for Density of Hydraulic Cement3
C 204 Test Method for Fineness of Hydraulic Cement by
Air Permeability Apparatus3
C 207 Specification for Hydrated Lime for Masonry Purposes3
C 230 Specification for Flow Table for Use in Tests of
Hydraulic Cement3
C 305 Practice for Mechanical Mixing of Hydraulic Cement
Pastes and Mortars of Plastic Consistency3
C 430 Test Method for Fineness of Hydraulic Cement by
the 45-m (No. 325) Sieve3
C 472 Test Methods for Physical Testing of Gypsum, Gypsum Plasters and Gypsum Concrete3
C 670 Practice for Preparing Precision and Bias Statements
for Test Methods for Construction Materials4
C 702 Practice for Reducing Field Samples of Aggregate to
Testing Size4
C 778 Specification for Standard Sand3
C 1005 Specification for Weights and Weighing Devices for
Use in the Physical Testing of Hydraulic Cements3
D 75 Practice for Sampling Aggregates5
1. Scope
1.1 These test methods cover physical testing of quicklime
and hydrated lime, and of limestone not otherwise covered in
ASTM standards.2
NOTE 1Quicklime and hydrated lime have a high affinity for moisture
and carbon dioxide. Caution should be taken to protect both hydrated and
quicklime during sampling, storage, and testing (see Practice C 50).
1.2 The test procedures appear in the following order:

Section
Air Entrainment
Apparent Loose Density of Hydrated Lime, Pulverized
Quicklime, and Limestone
Apparent Packed Density of Hydrated Lime, Pulverized
Quicklime, and Limestone
Autoclave Expansion of Hydrated Lime
Dry Brightness of Pulverized Limestone
Dry Screening by Air Jet Sieve
Fineness of Pulverized Quicklime and Hydrated Lime by Air
Permeability
Limestone Grindability
Particle Size of Pulverized Limestone
Plasticity of Lime Putty
Popping and Pitting of Hydrated Lime
Residue and Sieve Analysis
Settling Rate of Hydrated Lime
Slaking Rate of Quicklime
Specific Gravity of Hydrated Lime Products
Standard Consistency of Lime Putty
Water Retention of Hydrated Lime
Wet Sieve Analysis of Agricultural Liming Materials
13
16
17
8
15
19
18
20
14
7
9
5
11
12
21
6
10
22
1.3 The values stated in SI units are to be regarded as the

standard.
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2.1 ASTM Standards:
1
These test methods are under the jurisdiction of ASTM Committee C-7 on Lime
and are the direct responsibility of Subcommittee C07.06 on Physical Tests.
Current edition approved Jan. 10, 2000. Published March 2000. Originally
published as C 110 34 T. Last previous edition C 110 98.
2
For tests on limestone as aggregate, see Vol 04.02 of the Annual Book of ASTM
Standards. For tests on limestone as building stone, see Vol 04.05 of the Annual
Book of ASTM Standards.
Annual Book of ASTM Standards, Vol 04.01.

5
4
Copyright ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, United States.
C 110
E 11 Specification for Wire and Cloth Sieves for Testing
Purposes6
E 29 Practice for Using Significant Digits in Test Data to
Determine Conformance with Specifications6
E 691 Practice for Conducting an Interlaboratory Study to
Determine the Precision of a Test Method6
5.2.5 Attach a pressure gage to the water faucet and a rubber

tubing to the output side of the pressure gage. On the other end
of the rubber tubing attach the spray nozzle (see 5.2.3).
5.3 Residue of Quicklime:
5.3.1 Select a representative 2.5-kg (5-lb) sample of the
quicklime. Break lime selected for this test so as to entirely
pass a 25.0-mm (1-in.) square mesh screen. Test the pulverized
lime as received. Place the sample in a box of wood or of some
material of similarly low thermal conductivity, and an experienced operator should slake it with sufficient water at 21 to
27C (70 to 80F) to produce the maximum quantity of lime
putty, carefully avoiding burning or drowning the lime.
Allow it to stand for 1 h and then wash through an 850-m (No.
20) sieve by a stream of water having a moderate pressure. Do
not rub any material through the sieve. Continue the washing
until the residue on the screen appears to consist entirely of
coarse particles, but in no case continue the washing for more
than 30 min. Dry the residue to constant weight at a temperature of 100 to 107C (212 to 225F) and calculate the
percentage residue, based on the original weight of the sample.
5.4 Sieve Analysis of Hydrated Lime:
5.4.1 Select a 100-g sample of the hydrated lime as received
and place on a 600-m (No. 30) sieve, which is nested above
a 75-m (No. 200) sieve. Wash the material through the sieves
by means of a stream of water from the nozzle attached to a
rubber tubing (see 5.2.5) after adjusting the water pressure to
10 psi (69 kPa) 60.25 psi (61.7 kPa). Carefully wash the
sample through the sieves without allowing any splashing over
the sides of the sieve. After the sample is washed through the
top sieve, separate the two sieves and continue washing
through the 75-m (No. 200) sieve until the water coming
through the sieve is clear, that is, no particles can be seen in a
beaker of the rinse water, but in no case continue the washing
longer than 30 min. Take care not to let water accumulate on
the 75-m (No. 200) sieve, because the openings will become
clogged and the operation cannot be completed in 30 min.
5.4.2 Calculate the percentage residue retained on each
sieve, based on the original weight of the sample. The weight
of the material retained on the 600-m (No. 30) sieve shall be
added to the weight of the material retained on the 75-m sieve
to obtain the correct weight of the material retained on the
75-m sieve.
5.5 Sieve Analysis of Limestone and Dry Quicklime:
5.5.1 Select the desired sieves and nest them with the
coarsest sieves on top. Weigh a 100-g sample of the material to
be tested and place it on the top sieve. Conduct the sieving
operation by means of a lateral and vertical motion of the sieve
accompanied by a jarring action to keep the sample moving
continuously over the surface of the sieve. Continue sieving
until not more than 1 % of the residue passes any sieve during
1 min. If mechanical sieving is used, the device shall be such
as to impart the type of agitation described in the hand sieving
operation. Continue the shaking for a period of 15 min.
5.5.2 Weigh the residue retained on each sieve to the nearest
0.1 g. Report the results of the sieve analysis as follows: (1)
total percentages passing each sieve, (2) total percentages
retained on each sieve, or (3) percentages retained between
3. Terminology
3.1 DefinitionsUnless otherwise specified, for definitions
of terms used in this standard see Terminology C 51.
4. General Procedures
4.1 SamplingSamples of lime and limestone for chemical
analysis shall be taken and prepared in accordance with the
requirements of Practice C 50 applicable to the material to be
tested.
4.2 Calculation:
4.2.1 The calculations included in the individual procedures
sometimes assume that the exact weight specified has been
used. Accurately weighed samples which are approximately
but not exactly equal to the weight specified may be used
provided appropriate corrections are made in the calculation.
Unless otherwise stated, weights of all samples and residues
should be recorded to the nearest 0.0001 g.
4.2.2 In all mathematical operations on a set of observed
values, the equivalent of two more places of figures than in the
single observed values shall be retained. For example, if
observed values are read or determined to the nearest 0.1 mg,
carry numbers to the nearest 0.001 mg in calculation.
4.3 Rounding FiguresRounding of figures to the nearest
significant place required in the report should be done after the
calculations are completed, in order to keep the final results
free from calculation errors. The rounding procedure should
follow the principle outlined in Practice E 29.
5. Residue and Sieve Analysis
5.1 Significance and Use:
5.1.1 This test method determines the residue obtained from
slaking quicklime. Residue, in this case, is largely unreacted
material such as uncalcined limestone or dolomite, overburned
quicklime, or gross impurities, or a combination of these.
5.2 Apparatus:
5.2.1 The sieves used shall conform to the requirements of
Specification E 11. Preferably the sieves should have a 4-in.
depth.
5.2.2 If sieve calibrations are required, follow the method as
outlined in Test Method C 430.
5.2.3 Spray Nozzle conforming to the requirements of Test
Method C 430.7
5.2.4 Pressure Gage shall be 3-in. (75-mm) minimum
diameter, and shall be graduated in 1-psi (6.9 kPa) increments,
and shall have a maximum capacity of 30-psi (207 kPa). The
accuracy at 10 psi (69 kPa) shall be 60.25 psi (61.7 kPa).7

A wet washing spray attachment, Soiltest Model CL-364, or equivalent has
been found suitable for this purpose. Available from Soiltest, Inc., 86 Albrecht
Drive, P.O. Box 8004, Lake Bluff, IL 60044-8004.
7
C 110
6.2.3 Base PlateThe base plate for supporting the ring
mold shall be of plate glass and about 100 mm square.
6.2.4 Mechanical Mixers .8
6.3 Standard Consistency Determination:
6.3.1 Mechanical Mixing Procedure Using the Vac-UMixerTo a measured amount of water contained in an
800-cm3 Vac-U-Mix bowl, add 300 g of hydrated lime and
hand mix for 10 s with a stiff spatula (Note 2). Cover putty to
prevent evaporation of water. After the applicable soaking
period, 30 min maximum for Type S, special hydrated lime,
and not less than 16 h nor more than 24 h for Type N, normal
hydrated lime, insert the paddle assembly and mix the putty for
30 s with the mechanical mixer. Remove the paddle assembly
and scrape down any putty adhering to it and to the sides of the
mixing bowl. Remix for 30 s and determine the consistency as
prescribed in 6.3. If the penetration is less than 15 mm, return
all of the material to the mixer bowl, add additional water, and
remix for 15 s. If the penetration is greater than 25 mm, repeat
the test.
consecutive sieves, depending upon the form of the specification for the use of the material under test.
5.6 Precision and Bias:
5.6.1 No precision data are available due to the limited use
of these test methods. Therefore, users are advised to develop
their own laboratory precision. No statement is being made
about the bias of these test methods.
6. Standard Consistency of Lime Putty
6.1.1 In order to measure certain physical properties of a
lime putty, such as plasticity, it is necessary to have a uniform
or standard consistency (viscosity), since the property measurement is affected by the consistency level.
6.2 Apparatus:
6.2.1 Modified Vicat ApparatusThe apparatus, constructed as shown in Fig. 1, shall consist of a bracket, A,
bearing a movable brass rod, B, 6.3 mm in diameter and of
suitable length to fit the Vicat bracket. A plunger, C, 12.5 mm
in diameter, made of aluminum tubing, shall be attached to the
lower end of the rod. The total weight of the rod with plunger
shall be 30 g. The lower end of the plunger shall be closed
without shoulders or curvature and the tube may be loaded with
shot to the specified weight. The total weight required may also
be obtained by means of a weight, D, screwed into the rod. The
rod can be held in any position by means of a screw, E, and has
a mark midway between the ends which moves under a scale,
F, graduated in millimetres, attached to the bracket, A.
6.2.2 MoldThe conical ring mold shall be made of a
noncorroding, nonabsorbent material, and shall have an inside
diameter of 70 mm at the base and 60 mm at the top, and a
height of 40 mm.
NOTE 2Most lime hydrates will require 250 to 300 mL of water to

produce a putty of proper consistency for this test if 300 g of lime are used.
6.3.2 Mechanical Mixing Procedure Using the Hobart N-50

MixerTo a measured amount of water contained in the N-50
mixing bowl, add 600 g of hydrated lime and hand mix for 10
s with a stiff spatula (Note 3). Cover putty to prevent
evaporation of water. After the applicable soaking period, 30
min maximum for Type S, special hydrated lime, and not less
than 16 h nor more than 24 h for Type N, normal hydrated lime,
insert the paddle assembly and mix the putty for 1 min at a
slow speed. Stop the mixer and scrape down the paddle and the
sides of the mixing bowl. Remix for 4 min at a slow speed.
Determine the consistency as prescribed in 6.3.3. If the
penetration is less than 15 mm, return all of the material to the
mixing bowl, add additional water, and remix for 15 s. If the
penetration is more than 25 mm, repeat the test.
NOTE 3Most lime hydrates will require 500 to 600 mL of water to
produce a putty of proper consistency for this test if 600 g of lime are used.
6.3.3 Consistency DeterminationTo determine consistency, place the mold with its larger end resting on the glass
base plate and fill with the lime putty. Then strike off the putty
flush with the top of the mold. Center the lime putty, confined
in the ring mold resting on the plate, under the rod of the
modified Vicat apparatus (Fig. 1). Bring the plunger end, C, in
contact with the surface of the lime putty and take an initial
reading. Release the rod and take the final reading 30 s after the
plunger is released. The lime putty is of standard consistency
when a penetration of 20 6 5 mm is obtained. Record both the
total amount of water required to bring the putty to standard
consistency and the actual penetration. Proceed with the
plasticity determination in accordance with 7.3.
6.4.1 The precision and bias of this test method has not been
determined.
8
A Vac-U-Mixer or an N-50 Hobart Mixer, or equivalent, has been found
suitable for this purpose.
FIG. 1 Modified Vicat Apparatus
C 110
7.2.3 Absorption of Plasticimeter Base Plates:
7.2.3.1 Total AbsorptionPlasticimeter base plates when
immersed in water at room temperature for a period of 24 h
shall absorb not less than 40 g of water. Before making the
determination, dry the porcelain plates overnight in an oven at
temperatures of between 100 and 110C (212 and 230F) and
permit to cool to room temperature. Dry the plaster plates
overnight over calcium chloride at room temperature. After
immersion and before weighing, wipe off the excess water with
a damp cloth.
7.2.3.2 Rate of Absorption (Note 4)When tested over an
area 70 mm (234 in.) in diameter, the water absorbed shall be
in accordance with the following:
Time, min
Water Absorbed, mL
1
2
3
4
5
8 to 14
5 to 712
4 to 612
4 to 6
312 to 512
Constants of the Machine:

Absorption of Porcelain Base Plateminimum of 40 g in 24 h. For rate of
absorption of base plates see 7.2.3.2.
Dimension of Base Plate25 mm (1 in.) in thickness by 100 mm (4 in.) in
diameter.
Dimensions of Disk0.8 mm (132 in.) in thickness by 76 mm (3 in.) in
diameter.
Speed of Vertical Shaft1 revolution in 6 min, 40 s.
Torque on Disk when Bob Reading is 1001.41 Nm.
NOTE 4A convenient apparatus for determining the rate of absorption

consists of a buret sealed onto an inverted glass funnel from which the
stem has been removed. The diameter of the larger end of the funnel shall
be ground so as to be 70 mm (234 in.) in internal diameter. The funnel may
be attached to the plate on which the measurement is being made by
melted paraffin. The paraffin should not be too hot. A little experience will
indicate when it is of the proper consistency.
FIG. 2 Emley Plasticimeter
7.3 Plasticity Determination:

7.3.1 Lubricate a ring mold such as is described in 6.2.2
with a thin film of water, place on a porcelain base plate (see
7.2.2 and 7.2.3) or a disposable plaster base plate (see 7.2.3),
fill with the paste which has been adjusted to standard
consistency as described in 6.3.3, and strike off level. Remove
the mold by raising it vertically without distorting the paste.
Center the base plate and paste in the instrument and turn the
carriage up by hand until the surface of the paste is in contact
with the disk and the distance between the disk and the top of
the base plate is 32 mm (114 in.). Throw the carriage into gear
and start the motor. It is essential that the motor be started
exactly 120 s after the first portion of the paste has been placed
in the mold. Record the time when the first portion of paste is
placed in the mold as zero time; the motor is therefore started
at 2 min. Take care to protect the specimen from drafts during
the test.
7.3.2 Record the scale reading at 1-min intervals until the
test is completed. Consider the test complete when: (1) the
scale reading reaches 100, (2) any reading is less than the one
before, or (3) the scale reading remains constant for three
consecutive readings (2 min) and the specimen has visibly
ruptured or broken loose from the base plate. Note the time and
the scale reading at the end of the test.
7.4 Calculation:
7.4.1 Calculate the plasticity figure as follows:
7. Plasticity of Lime Putty

7.1.1 This test method provides a measure of the degree of
stiffening of lime putty of standard consistency as water is
withdrawn from it by a standard suction base plate.
7.1.2 Plasticity is an important property when applying
mixtures containing lime putty to porous or absorptive surfaces
such as in plastering, stuccoing, and masonry construction.
7.2 Apparatus:
7.2.1 Determine the plasticity of lime putty using the
plasticimeter shown in Fig. 2.9
7.2.2 Cleaning and Care of Base PlatesIn making the
plasticity determinations, much of the success attainable depends upon the condition of the base plates. In the case of
porcelain plates which are reused, improper cleaning results in
clogging of the pores with reduction in the rate of absorption.
After a plate has been used, wipe the excess lime off and
immerse the plate in clear water for not less than 2 h, after
which transfer it without drying to a dilute solution of
hydrochloric acid (HCl, 1 + 9) where it shall be kept immersed
for another 2 h. Then transfer to a receptacle containing
running water for at least 1 h. The plate is then free of acid.
After the removal of excess water, place the plate in an oven
overnight at a temperature of between 100 and 110C (212 and
230F) for drying. Before using, cool the plate to room
temperature.
P 5 =F2 1 ~10T!2
(1)
where
P 5 plasticity figure,
F 5 scale reading at the end of the test, and
T 5 time in minutes from the time when the first portion of
paste was put in the mold to the end of the test.
9
Emley Plasticimeters are no longer manufactured. If test is required, contact the
chairman of Subcommittee C07.06 through ASTM Headquarters, 100 Barr Harbor
Drive, West Conshohocken, PA 19428.
C 110
7.5.1 There are as yet insufficient analyzed data to permit
preparation of a precision and bias statement for this test
method. When data are collected and analyzed, precision and
bias statements will be proposed.
Standard portland cement

Standard aggregate (pulverized limestone)
Blend the mix until homogeneous.

8.4.2.3 Autoclave and calculate expansions of the test tablet
and the standard tablet in accordance with 8.3.1.
8.4.2.4 Determine the autoclave expansion of hydrated lime
for masonry purposes by subtracting the average percent
expansion of the standard tablet from the sample tablet.
of this test method. Therefore, users are advised to develop
their own laboratory precision. No statement is being made
about the bias of this test method.
8. Autoclave Expansion of Hydrated Lime

8.1.1 Expansion of pressed tablets of hydrated lime generally indicates the presence of unhydrated oxides of magnesium
and calcium. The relation of the degree of expansion in this test
method to field performance has not been determined.
8.2 Apparatus:
8.2.1 Mold and PressA steel mold capable of producing a
press tablet at least 0.032 m (1.25 in.) in diameter and 0.006 m
(0.25 in.) thick, and able to sustain at least 88.9 kN (20 000
lbf) pressure from a suitable press. It should be provided with
a release jig also.
8.2.2 Autoclave, capable of holding 1034 kPa (150 psi) for
2 h.
8.2.3 Micrometer, dial-type, capable of measuring 2.54 m
(0.0001 in.).
8.2.4 Microscope, with graduated lens for measuring 0.10
mm.
8.3 Procedure:
8.3.1 Weigh out 15 g of hydrated sample, place in the mold,
and press into a tablet. Press to 33.4 kN (7500 lbf) for 10 s,
then increase pressure to 88.9 kN (20 000 lbf) or more. Hold
for 10 s before releasing. Press tablet from mold with jig and
draw three diameter lines across the surface of the tablet using
a lead pencil. Draw two diameter lines normal to each other
and draw the third bisecting the 90 angles of the other two.
Measure the diameters with a dial micrometer and place the
tablet on the autoclave rack. Use aluminum foil to protect the
tablets from water dripping. Autoclave at 862 to 1034 kPa (125
to 150 psi) for 2 h. Begin timing when the pressure reaches 345
kPa (50 psi). After the autoclaving interval, allow the autoclave
to cool, remove the tablet, and remeasure the diameters.
Calculate the average percent expansion of the tablet from the
before and after measurements.
8.4 Expansion of Hydrated Lime-Portland CementAggregate:
8.4.1 Materials:
8.4.1.1 Standard CementType I or Type II portland cement.
8.4.1.2 Standard AggregatePulverized limestone, minus
212-m (No. 70) sieve, having less than 0.5 % silicon dioxide
(SiO2).
8.4.2 Procedure:
8.4.2.1 Test TabletMake up a pressed tablet in accordance
with the procedure outlined in 8.3.1 using the following
mixture for the sample:
Standard portland cement
Hydrated lime
Standard aggregate (pulverized limestone)
7g
16 g
9. Popping and Pitting of Hydrated Lime

9.1.1 Pops and pits are caused by the hydration and expansion of coarse particles of unhydrated lime or lime-impurity
reaction products present in the hydrated lime. The level of
popping and pitting in the sample is indicative of the potential
for the appearance of surface defects in plastering applications.
9.2 Gauging Plaster:
9.2.1 The gauging plaster used for the popping and pitting
test shall conform to the Test Methods section of Specification
C 28 and shall have a setting time of not more than 1 h when
tested in accordance with Test Methods C 472. Test the
gauging plaster without lime in the manner described in 9.3 to
ensure its freedom from pops and pits. If any pops or pits are
found, provide another lot of gauging plaster that is free of
pops and pits when subjected to this test.
9.3 Procedure:
9.3.1 Mix 100 g of hydrated lime with sufficient water to
bring to such a consistency as to give a penetration of 20 6 5
mm when tested in accordance with 6.3.3. Mix into this putty,
25 g of gauging plaster (9.2.1), adding more water as required
to maintain workable consistency. Spread on a glass plate to
make a pat at least 150 by 200 mm (6 by 8 in.) by
approximately 3 mm (18 in.) in thickness. Trowel to a smooth
finish. Allow to stand overnight.
9.3.2 Place the specimen and plate on a rack in the steam
bath so that water is not in contact with the specimen to be
tested. Provide a sloping cover above the specimen to prevent
condensed steam from dripping onto the surface of the specimen. Raise the temperature of the water in the steam bath to
boiling and maintain at boiling for 5 h. Remove the specimens
from the bath and examine for pops and pits.
9.3.3 The pitting potential of hydrated lime can be determined in conjunction with autoclave expansion as in 8.3.1.
However, it is not necessary to measure diameter, if only the
pitting potential is to be determined. After following the
procedure for expansion in 8.3.1, examine the pressed tablet
under the measuring microscope, and count and measure the
pits in millimetres.
14 g
8g
72 g
10. Water Retention of Hydrated Lime

10.1.1 This test method measures the ability of the hydrated
lime in a plastic mix with sand to retain water, and hence retain
consistency of the mix, when subjected to an applied suction.
Blend the mix until homogeneous.

8.4.2.2 Standard TabletMake up a pressed tablet in accordance with the procedure outlined in 8.3.1 using the
following mixture for the sample:
5
C 110
10.3 Consistency:
10.3.1 ApparatusThe flow table and mold used for the
measurement of consistency of the mortar shall conform to
Specification C 230.
10.3.2 ProcedureCarefully wipe dry the flow table top
and place the flow mold at the center. Immediately after
completing the mixing operation, fill the mold with mortar
gently pressed into place by the finger tips to ensure uniform
filling free of voids. Smooth off the mortar level with the top of
the mold by aid of a trowel, and remove the mold. Immediately
drop the table through a height of 13 mm (12 in.), 25 times in
15 s. The flow is the resulting increase in diameter of the
mortar mass, expressed as the percentage of the original
diameter. The mortar may be adjusted, if the flow is below
100 %, by additions of water until the flow is within the range
from 100 to 115 %. Make each adjustment by returning the
mortar to the original mixing bowl, add water, and then mix at
medium speed (2856 10 r/min) for 30 s. If the flow of the
original mortar is greater than 115 %, prepare a new batch.
10.4 Water Retention Test:
10.4.1 ApparatusThe equipment used to determine water
retention shall conform to the same apparatus used for the
water retention test in Specification C 91 (see Fig. 3).
10.4.2 Procedure:
10.4.2.1 Adjust the mercury relief column to maintain a
vacuum of 50.8 mm as measured on the manometer. Seat the
perforated dish on the greased gasket of the funnel. Place a
wetted filter paper in the bottom of the dish. Turn the stopcock
to apply the vacuum to the funnel and check the apparatus for
This ability, measured as a percent of the original consistency,

is indicative of the workability to be expected in a masonry
containing the lime.
10.2 Proportioning and Mixing:
10.2.1 ApparatusThe apparatus used shall conform to
Practice C 305.
10.2.2 ProportionsThe mortar tested shall be composed
of 500 g of lime and 1500 g of standard sand conforming to
13.2.4. If hydrated lime putty is used, use that weight of putty
that is equivalent to 500 g of dry hydrated lime.
10.2.3 Mechanical Mixing:
10.2.3.1 Place the dry paddle and the dry bowl in the mixing
position in the mixer.
10.2.3.2 Place a measured quantity of water in the bowl.
10.2.3.3 Add the lime to the water, then start the mixer and
mix at slow speed (140 6 5 r/min) for 30 s.
10.2.4 Add the entire quantity of sand slowly over a 30-s
period while mixing at slow speed.
10.2.5 Stop the mixer, change to medium speed (285 6 10
rpm) and mix for 30 s.
10.2.6 Stop the mixer and let the mortar stand for 112 min.
(During the first 15 s of this interval, quickly scrape down into
the batch any mortar that may have collected on the side of the
bowl, then for the remainder of this interval cover the bowl
with the lid.)
10.2.7 Finish the mixing for 1 min at medium speed.
10.2.8 In any case requiring a remixing interval, any mortar
adhering to the side of the bowl shall be quickly scraped down
into the batch prior to remixing.
FIG. 3 Apparatus Assembly for the Water Retention Test
C 110
23 6 1.7C (73.46 3F) and mix thoroughly by alternately
inverting and righting the cylinder slowly for a period of 2 min.
Allow the graduate and contents to stand at 23 6 1.7C for 30
min and then dilute to the 100-mL mark with CO2-free distilled
water at 23 6 1.7C. Mix contents again thoroughly as before
and allow to stand undisturbed at 23 6 1.7C for 24 h.
11.3 Report:
11.3.1 Report the sedimentation height in millilitres after 14,
12, 34, 1, 2, 4, and 24 h, reading the bottom of the meniscus.
leaks and to determine that the required vacuum is obtained.

Then turn the stopcock to shut off the vacuum from the funnel.
10.4.2.2 Immediately after the final consistency test
(10.3.2), return all of the mortar to the bowl and remix the
entire batch for 15 s at medium speed. Immediately after
remixing the mortar, fill the perforated dish with the mortar to
slightly above the rim. Tamp the mortar 15 times with the
tamper. Apply ten of the tamping strokes at approximately
uniform spacing adjacent to the rim of the dish and with the
long axis of the tamping face held at right angles, to the radius
of the dish. Apply the remaining five tamping strokes at
random points distributed over the central area of the dish. The
tamping pressure shall be just sufficient to ensure filling of the
dish. On completion of the tamping, the top of the mortar
should extend slightly above the rim of the dish. Smooth off the
mortar by drawing the flat side of the straightedge (with the
leading edge slightly raised) across the top of the dish. Then cut
off the mortar to a plane surface flush with the rim of the dish
by drawing the straightedge with a sawing motion across the
top of the dish in two cutting strokes, starting each cut near the
center of the dish. If the mortar is pulled away from the side of
the dish during the process of cutting off the excess mortar,
gently press the mortar back into contact with the side of the
dish using the tamper.
10.4.2.3 Turn the stopcock to apply vacuum to the funnel.
After suction for 60 s, quickly turn the stopcock to expose the
funnel to atmospheric pressure. Immediately slide the perforated dish off the funnel, touch it momentarily on a damp cloth
to remove droplets of water, and set the dish on the table. Then
using the bowl scraper (rubber scraper as specified in Practice
C 305), plow and mix the mortar in the dish for 15 s. Upon
completion of mixing, place the mortar in the flow mold and
determine the flow. Carry out the entire operation without
interruption and as quickly as possible. Not more than 30 min
should be required for completion, starting from the completion of the mixing of the mortar for the first flow determination.
10.4.3 Calculation:
10.4.3.1 Calculate the water retention value for the mortar
as follows:
Water retention value 5 ~A/B! 3 100
NOTE 5Slight variations in results of this test method on a sample run

in different laboratories or by different operators are permissible. The test
is not an absolute one, but is designed to distinguish between fast and slow
settling hydrates.

their own laboratory precision.
12. Slaking Rate of Quicklime
12.1.1 The temperature rise in 30 s is a measure of the
reactivity of the softer-burned portion of the quicklime. Total
slaking time provides a measure of the overall degree of
reactivity of the material. Total temperature rise is largely
dependent on the available lime content of the sample.
12.1.2 These slaking parameters provide an indication of
the performance of the quicklime to be expected in industrial
slaking systems. Slaking characteristics have an effect on lime
slurry properties such as settling characteristics, viscosity,
particle size, and reaction rate.
12.2 Apparatus:
12.2.1 Mechanical Stirrer ,10 speed 400 6 50 r/min, fitted
with a special stirring rod.
12.2.2 Modified Dewar Flask ,11 665-mL, fitted with special
rubber gasket covers.
12.2.3 Thermometer, dial-type, 0 to 100C range in 1C
increments or thermocouple with a response time equivalent to
or faster than the dial thermometer.
12.2.4 Torsion Balance.
12.2.5 Sieve, 203-mm (8-in.), 3.35-mm (No. 6), conforming
to Specification E 11.
12.2.6 An apparatus essentially the same as that illustrated
in Fig. 4 and Fig. 5 shall be used. The apparatus consists of a
covered reaction container fitted with a mechanical stirrer and
thermometer. The quicklime charge shall be stirred with a
mechanical stirrer fitted with a stainless steel rod, the end of
which is formed into a loop to follow the contour of the
reaction container. The vacuum reaction flask shall be provided
with a cover consisting of two circular pieces of gasket rubber
sheet, approximately 3 mm (18 in.) thick. The first piece is
provided with a single radial slot that slides over the stirring
rod and the thermometer. The second piece (top) has a similar
slot plus a hole to provide for the dial thermometer. When the
two cover pieces are in place, the slot on the lower piece is at
right angles to the slot on the upper piece with the thermometer
(2)
where:
A 5 flow after suction, and
B 5 flow immediately after mixing.
their own laboratory precision.
11. Settling Rate of Hydrated Lime
11.1.1 This test method provides a measure of the rate of
settling of a hydrated lime slurry, a form in which this material
is frequently used. In some applications a slow settling slurry
is desirable; in others, fast settling is preferred.
11.2 Procedure:
11.2.1 Place 10.0 g of lime hydrate in a 100-mL glassstoppered graduated cylinder (internal diameter about 24 mm).
Wet with 50 mL of carbon dioxide (CO2) free distilled water at
10
11
A Fisher 14-498, or equivalent, has been found suitable for this purpose.
A Fisher 10-197, or equivalent, has been found suitable for this purpose.
C 110
FIG. 4 Slaking Reactivity Apparatus
mm (No. 6) sieve as possible. It is not necessary that 100 % of

the sample pass a 3.35 mm (No. 6) sieve, but all of the sample,
including the plus 3.35 mm (plus No. 6) fraction, must be used
in the test.
12.3.2 Slaking RateAdjust the temperature of about 500
mL of distilled water in accordance with the schedule given in
Table 1, and add the specified amount to the Dewar flask. Set
the agitator revolving at 400 6 50 r/min. The temperature of
the water in the flask must be 60.5C of the desired temperature. Quarter and weigh out the required amount of the
prepared quicklime sample. Add the quicklime to the water
without delay and simultaneously begin timing. Put the covers
in place immediately. Take a reading at each 30 s interval.
12.3.3 Continue readings until less than 0.5C temperature
change is noted in each of three consecutive readings. The total
active slaking time will then be the time at which the first of the
three consecutive readings was taken. The temperature at this
time will be considered the final reaction temperature. Subtract
the initial temperature from the final temperature to obtain the
total temperature rise. Subtract the initial temperature from the
temperature at 30 s for the temperature rise in 30 s. Subtract the
initial temperature from the temperature at 3 min for the
temperature rise in 3 min.
12.4 Report:
12.4.1 Record the actual temperature rise and plot a suitable
FIG. 5 Stirring Rod Detail
stem extending through the lower slot. The apparatus may be

assembled by any convenient supporting equipment.
12.3 Procedure:
12.3.1 Prepare the sample of quicklime (as rapidly as
possible to prevent sample deterioration) so that a majority of
the material passes a 3.35 mm (No. 6) sieve. Place the sample
in an airtight container and allow to come to room temperature
before testing. The slaking rate of lime is significantly affected
by the particle size of the sample and must be as close to a 3.35
TABLE 1 Schedule for Slaking Rate
Temperature of water, C
Quantity of water, mL
Quantity of quicklime, g
Material to Be Tested
Dolomitic
High Calcium
40
25A
400
400
120
100
A
Initial temperature of 40C may be used, provided the report of results states
the initial temperature.
C 110
TABLE 3 Unit Weights and Apparent Specific Gravities
curve showing temperature rise as the ordinate and time as the

abscissa. The results may also be reported as:
12.4.1.1 Temperature rise in 30 s (or at any other designated
time) in degrees Celsius,
12.4.1.2 Total temperature rise in degrees Celsius, and
12.4.1.3 Total active slaking time in minutes.
12.5.1 Twelve laboratories cooperated in the testing of five
high calcium quicklimes and four dolomitic quicklimes thereby
obtaining the repeatability (r) and reproducibility (R) (Practice
E 691) data contained in Table 2.
12.5.2 Due to the lack of a recognized industry standard, the
bias of this test method has not been determined. The variety of
reporting options also complicates obtaining a suitable bias
statement.
Materials
Portland cement
Hydrated lime
Blended Ottawa sand
Results in C Rise
High Calcium
High Calcium
Dolomitic
Dolomitic
12
11
10
9
Time
Range Tested
30 s
3 min
30 s
3 min
12.344.4
32.156.1
3.612.0
21.236.4
1.56
1.72
1.38
1.62
4.21
4.72
2.84
3.72
1,504 (94)
800 (50)
1,280 (80)
3.15
2.30
2.65
TABLE 4 Weight of Materials for Mortar Batch

Mortar
Type
(C 270)
Proportions
by Volume
M
S
N
O
Lime/Sand
1:14:3
1:12:412
1:1:6
1:2:9
1:3
Portland
Cement, g
Hydrated
Lime, g
Blended
Ottawa
Sand, g
564
376
282
188
0
75
100
150
200
300
1,440
1,440
1,440
1,440
1,400
13.4 Procedure:
13.4.1 If the mortar has the correct flow, use a separate
portion of the mortar for the determination of entrained air.
Determine the weight of 400 mL of mortar in accordance with
Test Method C 185.
13.5 Calculation:
13.5.1 Calculate the air content of the mortar and report it to
the nearest 0.1 % as follows:
D 5 ~W1 1 W2 1 W3 1 Vw!/
@~W1/S1! 1 ~W2/S2! 1 ~W3/S3! 1 Vw# A
5 100 2 ~Wm/4D!
where:
D
5
W1 5
W2 5
W3 5
Vw 5
S1 5
S2 5
S3 5
A
5
Wm 5
(3)
density of air-free mortar,

weight of portland cement, g,
weight of hydrated lime, g,
weight of blended Ottawa sand, g,
water used, mL,
specific gravity of portland cement,
specific gravity of hydrated lime,
specific gravity of blended Ottawa sand,
volume % of entrained air, and
weight of 400 mL of mortar, g.
NOTE 6For lime/sand mortars, W1 and S1 should be dropped from the

calculation.

13.6.1 The single operator within laboratory standard deviation has been found to be 0.56 % air content throughout the
range of 8 % to 19 % air content. Therefore results of two
properly conducted tests by the same operator on similar
batches of mortar should not differ by more than 1.6 % air
content.
13.6.2 The multilaboratory standard deviation has been
found to be 1.0 % air content throughout the range of 8 % to
19 % air content. Therefore, results of two different laboratories on similar batches of mortar should not differ from each
other by more than 2.8 % air content (see Test Method C 185).
TABLE 2 Precision Data

Labs
Specific
Gravity
A
The unit weight values listed for cementitious materials are assumed values
commonly used in construction practice.
13. Air Entrainment

13.1.1 Hydrated lime, particularly that containing an airentraining additive, used in masonry mortar may contribute to
the air content of the mortar. Certain specifications and
applications of mortar place a limit on this air content.
13.2 Apparatus:
13.2.1 Scales, Sieves, Glass Graduates, Tamper, Measure,
Straightedge, Spatula, Tapping Stick, and Spoon, conforming
to the requirements given in Test Method C 185.
13.2.2 Flow Table, conforming to the requirements prescribed in Specification C 230.
13.2.3 Mixing Apparatus, conforming to the requirements
as prescribed in Practice C 305.
13.2.4 The sand shall be a blend of equal parts by weight of
graded Ottawa sand and standard 2030 Ottawa sand. The
fineness of graded Ottawa sand and standard 2030 sand may
be checked by using the methods described in Specification
C 778.
13.3 Preparation of Mortar:
13.3.1 Proportions for MortarPortland cement-hydrated
lime mortar for measurement of air entrainment shall be
proportioned to conform, in batch size, to the unit weights by
volume of cementitious material and aggregate as shown in
Table 3. The portland cement shall conform to Specification
C 150, and the hydrated lime to Specification C 207. The
quantity of water, measured in millilitres, shall be such as to
produce a flow of 110 6 5 % as determined by the flow table.
Proportions for the generally used batch sizes based on Table 2
material unit weight shall contain the weights as prescribed in
Table 4.
13.3.2 Mixing of MortarsMix the mortar in accordance
with the procedure for mixing pastes in Practice C 305.
13.3.3 Determination of FlowDetermine the flow in accordance with the Procedure section of Test Method C 109.
Material
Unit weight,
kg/m3(lb/ft3)A
14. Particle Size of Pulverized Limestone

14.1.1 Particle size of pulverized limestone, as the word is
used in these methods, is the percent distribution of the
9
C 110
(ASTM 152H), variations of as much as 1.0-scale divisions
between two similar hydrometers have been noted. The correction factor brings all four into line with one another. It is not
necessary to repeat this calibration unless changing to a
different hydrometer.
14.4.3 Weigh 40 g of sample.
14.4.4 Add approximately 300 mL of distilled water to the
mixer, 30 mL of the particle-dispersing solution, followed by
40 g of unknown sample. Cover. Agitate for exactly 2 min at
high speed.
14.4.5 Transfer the slurry quantitatively to the 1000-mL
sedimentation cylinder. Make up to approximately 3.2 mm (18
in.) above the mark since it must be read from the top (as the
bottom of the meniscus is not visible) and this will approximate
the 1000-mL calibration of the cylinder. Cylinder temperature
can be adjusted to 20C by running cool water on the outside
of the cylinder and stirring with a thermometer until 20C is
reached. Cap with the rubber stopper. Mix well by inverting the
cylinder 15 or more times. Remove the stopper and put the
cylinder in a water bath that has been previously adjusted to as
close to 20C as is possible. Start the stop watch and note the
time on the clock. At exactly 412 min after start, carefully insert
the hydrometer to the approximate point where the reading is
to be made. Take the reading at exactly 5 min. Record the
reading and temperature (Note 7). Remove the hydrometer and
wash clean of any slurry. Cover the cylinder with the watch
glass.
equivalent spherical diameter of the individual particles expressed in micrometres, using the principle of sedimentation
and Stokes law for particle size determination. It is intended
for use with pulverized limestones with not more than 0.5 %
residue on a 45-m (No. 325) sieve.
14.2 Apparatus:
14.2.1 Soil Hydrometer, ASTM 152H.12
14.2.2 Sedimentation Cylinder, ASTM, 1000-mL capacity.
14.2.3 Rubber Stopper, Size 12.
14.2.4 Thermometer, 0 to 105C.
14.2.5 Stop Watch.
14.2.6 Regular Clock or Watch.
14.2.7 Mixer .13
14.2.8 Water Bath.
14.2.9 Balance .14
14.2.10 Watch Glass.
14.2.11 Graph Paper ,15 3 cycles 3 70 divisions.
14.2.12 Sieve, 45-m (No. 325), stainless steel cloth, brass
frame, 8-in. diameter.
14.2.13 Sieve, 500-mesh, stainless steel cloth, brass frame,
4-in. diameter, 5-in. tall frame.
14.3 Reagents:
14.3.1 Particle-Dispersing Agent 16 (30 mL of 25 % solution is diluted up to 400 mL with distilled water).
14.4 Procedure:
14.4.1 Determine meniscus correction by inserting the hydrometer in the sedimentation cylinder filled to mark with
distilled water. Record the reading at the top of the meniscus
and at the bottom of the meniscus. The difference between the
two readings is the meniscus correction. For example, in Fig. 6,
the correction for the hydrometer used is 1.2. This reading is
added to each R to obtain Rr.
14.4.2 Calibrate the hydrometer by adding 30 mL of the
particle-dispersing solution to the sedimentation cylinder, then
bringing up to the mark with distilled water at 27C. Mix
thoroughly and take a hydrometer reading (read at the top of
the meniscus). Repeat after cooling the cylinder to 17C and
adjusting the meniscus so it is on the mark. Assume a
straight-line relationship and draw a line that gives the composite correction factor. This factor is the difference between
the reading and zero. These are the corrections entered in Table
5 and should be determined for each hydrometer. Four factors
are compensated for in the correction factor: (1) Temperature:
Hydrometers and cylinders are calibrated at 20C; variations
from this temperature produce inaccuracy in the hydrometer
reading; (2) Specific gravity: Addition of dispersant changes
the specific gravity of the solution; (3) Meniscus correction:
Hydrometers are graduated to read at the bottom of the
meniscus but opaque calcium carbonate solutions require
readings at the top of the meniscus; and (4) Hydrometers: In
spite of the supposed similarity in volume of the hydrometers
NOTE 7Temperature must be taken inside the cylinder and not in the
water bath.
14.4.6 Take additional readings at 15, 30, 60, 120, or 180

min; 300 or 360 min; and 1200 or 1440 min after the start.
14.4.7 Take a 25-g sample and run a 500-mesh wet-sieve
test. The opening of the 500-mesh sieve is approximately 25
m. From this result calculate the percent finer than 25 m. Do
not discard the plus 500-mesh but use this with the 45-m (No.
325) sieve to obtain the percent finer than 44 m. The opening
of the 45-m sieve is 44 m.
14.5 Calculation:
14.5.1 Arrange the data on a sample sheet.
14.5.2 Record the date and clock readings as readings are
taken.
14.5.3 Readings are usually taken at 5, 15, 30, 60, 180, 360,
and 1440 min. The 25-m point is obtained from the 500-mesh
sieve result and the 44-m point is obtained from the 45-m
sieve result.
14.5.4 Record the temperature, T, and the hydrometer reading, R, for each reading.
14.5.5 Obtain Rr by adding the meniscus correction to each
R value.
14.5.6 Obtain Rc, the corrected hydrometer reading, from
Fig. 6. This value can be different for each hydrometer and
must be individually determined.
14.5.7 Obtain L from Table 6 using Rr values.
14.5.8 =L/T is found from Fig. 7 and the values for L and
T (time). For times not in Fig. 7, calculate the =L/T since the
values for L and T (in minutes) are known.
14.5.9 Find D at 20C in terms of =L/T using Table 7.
14.5.10 . To correct D for temperature, use Table 8 and find
12
Available from Taylor Instrument Co., Catalog No. 22297.

The Hamilton Beach Model No. 210 mixer, or equivalent, has been found
14
The OHaus CG 311 balance, or equivalent, has been found suitable.
15
Dietzgen No. 340-L310 or Keuffel and Esser No. 359-71G graph paper, or
equivalent, has been found suitable.
16
Daxad 30, a particle dispersing agent, has been found suitable, and is available
from the Dewey and Almy Div. of W. R. Grace Co.
13
10
C 110
FIG. 6 Composite Correction Factor for Hydrometer

TABLE 5 Hydrometer Composite Correction Factor
Temperature, C
Correction Factor
17
18
19
20
21
22
23
24
25
26
27
+1.90
+1.52
+1.14
+0.76
+0.39
0.00
0.38
0.76
1.14
1.52
1.90
14.5.12 The values of Dc are now plotted against the values

of P.
14.6.1 The precision and bias of this test method has not
been determined.
15. Dry Brightness of Pulverized Limestone
15.1 Summary of Test Method:
15.1.1 A sample of the dry material is compressed and its
reflectance measured on a reflectometer that has previously
been standardized.
15.2.1 This test method provides a measure of the reflectance, or whiteness, or both of ground calcium carbonate
products by comparison with a standard, using green and blue
filters.
15.3 Apparatus:
DD in terms of =L/T . Multiply by DT (DT is the difference

in temperature between 20C and the actual temperature of the
test). This will give a value to be subtracted from the D found
in 14.5.9 if the temperature is above 20C. If the temperature
is below 20 C, this correction should be added.
14.5.11 Find P by using Table 8 and the value for Rc.
11
C 110
TABLE 6 Effective Depth, L, for Hydrometer 152H
Rr
L, cm
Rr
L, cm
0
1
2
3
4
5
6
16.3
16.1
16.0
15.8
15.6
15.5
15.3
31
32
33
34
35
36
37
11.2
11.1
10.9
10.7
10.6
10.4
10.2
7
8
9
10
11
12
15.2
15.0
14.8
14.7
14.5
14.3
38
39
40
41
42
43
10.1
9.9
9.7
9.6
9.4
9.2
13
14
15
16
17
18
19
20
21
14.2
14.0
13.8
13.7
13.5
13.3
13.2
13.0
12.9
44
45
46
47
48
49
50
51
52
9.1
8.9
8.8
8.6
8.4
8.3
8.1
7.9
7.8
22
23
24
25
26
27
28
29
30
12.7
12.5
12.4
12.2
12.0
11.9
11.7
11.5
11.4
53
54
55
56
57
58
59
60
7.6
7.4
7.3
7.1
7.0
6.8
6.6
6.5
15.5.2.2 The Eastman Kodak barium sulfate reflectance

standard is provided with reflectance values at various wavelengths. Since some variation is possible between lots of
BaSO4, the values used to standardize the reflectometer must
be calculated. A normal Y value will be between 99.0 and 98.5,
depending on the lot number.
15.5.2.3 After this has been accomplished, a reading of the
white standard plaque can be taken and the values of X, Y, and
Z recorded. This plaque can then be used as a secondary
standard for future standardizations. This reduces the necessity
of making a barium sulfate pellet for every test series.
15.6 Procedure:
15.6.1 The reflectometer must be given ample warm-up
time prior to the sample readings.
15.6.2 The reflectometer must first be standardized; this
consists of standardization of the bottom of the scale and
standardization of the upper part of the scale.
15.6.3 Sample pellets should then be pressed (Note 8)
following manufacturer instructions explicitly (Note 9).
NOTE 8Ground products with more than 0.5 % residue on a 45-m
(No. 325) screen will require special care in preparing the sample cup. The
coarser the product, the harder to obtain a compact, smooth surface.
NOTE 9Some reflectometers and spectrophotometers can measure
reflectance with the powder sample in a horizontal position, thus eliminating the necessity to prepare a sample pellet. Also, coated ground
limestones are difficult to pelletize. Loose powder samples should be
smoothed in a convenient sized container until the surface is level and free
from cracks and other surface defects.
15.6.4 After the reflectometer has been standardized, the

sample pellets are centered beneath the opening and positioned
so that no light escapes from the pellet-opening interface.
15.6.5 The samples are then read for X, Y, Z, L, a, and b
values. These values are recorded.
15.6.6 To determine if the values of the reflectometer have
drifted, the white standard (either the barium sulfate pellet or
the porcelain plaque) is placed over the specimen port and
read. Values should be the same as those placed in the
processor during the standardization procedure.
15.7 Report:
15.7.1 The Y value is recorded as the dry brightness of that
specific limestone.
15.8.1 The same instrument, operator, and standard should
reproduce 60.2 %. Different instrument (Note 10), operators,
and standard should agree 61.0 %.
15.3.1 Reflectometer :17

15.3.2 Dry Powder Press (See Fig. 8)18Instructions, as
supplied by the manufacturer, for preparation of the sample and
use of the powder press shall be explicitly followed.
15.3.3 White Porcelain Standard Plaque, to be used as
secondary standard.
15.4 Reagent:
15.4.1 Barium Sulfate (BaSO4)Use Eastman Kodak19
Chemical No. 6091, white reflectance standard only.
15.5 Calibration and Standardization:
15.5.1 Zero Scale Calibration (bottom of scale standardization):
15.5.1.1 Place the black glass provided with the instrument
over the specimen port, so that the shiny side is towards the
opening. The glass should be positioned so that no light
escapes from the black glass-opening interface.
15.5.1.2 The processor is then adjusted to read zero reflectance.
15.5.2 Standardizing of the White Standard (standardization
of the upper part of the scale):
15.5.2.1 A primary standard pellet (barium sulfate) which is
free from surface flaws should be positioned over the specimen
port so that no light can escape at the pellet-opening interface.
NOTE 10It is recognized that there are various manufacturers of

reflectometers, and testing has been undertaken to relate X, Y, and Z
tristimulus color values from one instrument to another. If results of this
comparison testing are desired, please contact the Pulverized Limestone
Association.
16. Apparent Loose Density of Hydrated Lime,

Pulverized Quicklime, and Limestone
16.1.1 This test method determines the loose or unsettled
density of hydrated lime, pulverized quicklime, and limestone.
It provides for an approximate measure of the maximum
volume occupied by a given weight of hydrated lime, pulverized quicklime, or limestone.
17
The Hunter D25A-Tristimulus colorimeter, or equivalent, has been found
18
The Bausch and Lomb or Carl Zeiss Dry Powder Press Assembly, or
equivalent, has been found satisfactory for this purpose.
19
Registered trademark.
12
C 110
FIG. 7 Values for
TABLE 7 D as Related to
=L / T
=L/T as Related to Lfor Given Values of T (Time)
=L / T at 20C
=L / T
D, m
TABLE 8 DD from
=L / T
D, m
=L / T
DD
0.05
0.10
0.15
0.20
0.25
0.7
1.4
2.0
2.7
3.4
1.05
1.10
1.15
1.20
1.25
14.0
14.7
15.4
16.0
16.7
2.0
1.9
1.8
1.7
1.6
0.32
0.31
0.29
0.27
0.26
0.30
0.35
0.40
0.45
0.50
4.0
4.7
5.4
6.0
6.7
1.30
1.35
1.40
1.45
1.50
17.4
18.0
18.7
19.4
20.1
1.5
1.4
1.3
1.2
1.1
0.24
0.23
0.21
0.19
0.18
0.55
0.60
0.65
0.70
0.75
7.4
8.0
8.7
9.4
10.0
1.55
1.60
1.65
1.70
1.75
20.8
21.4
22.1
22.8
23.4
1.0
0.9
0.8
0.7
0.6
0.16
0.15
0.13
0.11
0.10
0.80
0.85
0.90
0.95
1.00
10.7
11.4
12.0
12.7
13.4
1.80
1.85
24.1
24.8
0.5
0.4
0.3
0.2
0.1
0.08
0.07
0.05
0.03
0.02
16.2 Apparatus:
16.2.1 Flour SifterA 114 to 127 mm (412 to 5 in.)
kitchen-type flour sifter of either the squeeze handle type or the
hand crank type. It shall be able to hold at least 300 g of
hydrated lime or 500 g of limestone or quicklime. The wire
mesh openings should be between 0.8 and 1.5 mm.
16.2.2 Density Cup, 400 mL cylindrical cup as described in

the Apparatus Section of Test Method C 185.
16.2.3 Balance, suitable for weighing at least 800 g accurately to 0.1 g.
16.2.4 Clock or Watch.
16.2.5 Straight Edge.
13
C 110
TABLE 9 Values for P as Related to Rc, Using a 5 0.988
and W 5 40
16.3.4 Weigh the cup and sample to the nearest 0.1 g and
determine the weight of the sample by difference.
16.3.5 The loose density of the material is calculated and
reported as grams per cubic centimetre, or as pounds per cubic
foot.
16.4 Calculation:
16.4.1 Calculate the loose density as follows:
NOTE 1Calculate to nearest 0.1 of Rc. For a reading of 24.7, take

reading of 24.5 which is 60.0 and add 2 3 0.4 or 60.8%.
Rc
Rc
Rc
Rc
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10.0
10.5
11.0
0.0
1.5
2.5
3.5
5.0
6.0
7.5
8.5
10.0
11.0
12.5
13.5
15.0
16.0
17.5
18.5
20.0
21.0
22.5
23.5
25.0
26.0
27.5
11.5
12.0
12.5
13.0
13.5
14.0
14.5
15.0
15.5
16.0
16.5
17.0
17.5
18.0
18.5
19.0
19.5
20.0
20.5
21.0
21.5
22.0
22.5
28.5
30.0
31.0
32.0
33.5
35.0
36.0
37.5
38.5
39.5
40.5
42.0
43.0
44.5
45.5
47.0
48.0
49.5
50.5
52.0
53.0
54.5
56.5
23.0
23.5
24.0
24.5
25.0
25.5
26.0
26.5
27.0
27.5
28.0
28.5
29.0
29.5
30.0
30.5
31.0
31.5
32.0
32.5
33.0
33.5
34.0
57.0
58.0
59.0
60.0
62.0
63.0
64.0
65.0
66.5
67.5
69.0
70.0
71.5
72.5
74.0
75.0
76.5
77.5
79.0
80.0
81.5
82.5
84.0
34.5
35.0
35.5
36.0
36.5
37.0
37.5
38.0
38.5
39.0
39.5
40.0
40.5
85.0
86.5
87.5
89.0
90.0
91.5
92.5
94.0
95.0
96.5
97.5
99.0
100.0
D 5 W/V
(4)
where:
D 5 loose density,
W 5 weight of sample, g, and
V 5 volume of cup, cm3.
16.4.2 For reporting as pounds per cubic foot, multiply
grams per cubic centimetre by 62.43.
16.5.1 Single Operator PrecisionThe single operator
standard deviation has been found to be 0.4 lb/ft3(Note 10).
Therefore, results of two properly conducted tests by the same
operator on the same material should not differ by more than
1.13 lb/ft3.
16.5.2 Multilaboratory PrecisionThe multilaboratory
Therefore, results of two properly conducted tests from two
different laboratories on samples of the same material should
not differ by more than 3.6 lb/ft3.
NOTE 11These numbers represent, respectively, the (1s) and (d2s)
limits as described in Practice C 670.
16.5.3 The above precision statements are based on a

multilaboratory testing program for determination of the loose
bulk density of hydrated lime. No statement is made regarding
the precision of this method as it relates to other materials. Due
to a lack of a recognized industry standard, the bias of this test
method has not been determined.
17. Apparent Packed Density of Hydrated Lime,
Pulverized Quicklime, and Limestone
17.1.1 This test method determines the packed or settled
density of hydrated lime, pulverized quicklime, and limestone.
It provides for determining the minimum volume occupied by
a given weight of hydrated lime, pulverized quicklime or
limestone.
17.2 Apparatus:
17.2.1 Graduated Cylinder, 100 mL capacity.
17.2.2 Balance, accurate to 0.1 g.
17.3 Procedure:
17.3.1 Weigh to within 0.1 g a 25 g sample of powdered
material and transfer it to the graduated cylinder.
17.3.2 Allow powder to settle by gently tapping the cylinder
on a desk top cushioned with a thick magazine or writing tablet
so that compaction occurs without fluffing.
17.3.3 Record the volume of the lime after each 100 taps
and continue tapping until compaction volume change is less
than 0.5 mL/100 taps.
17.3.4 Calculate the density in grams per cubic centimetre
or in pounds per cubic foot to the nearest pound.
17.4 Calculation:
17.4.1 Calculate the packed density as follows:
FIG. 8 Dry-Powder Press
16.3 Procedure:
16.3.1 Weigh the empty density cup to the nearest 0.1 g on
a balance. Place the tared cup on a solid table with a suitable
mat inserted underneath the cup to collect excess sample
spilling over the cup. Fill the flour sifter with more than enough
material to fill the density cup. Start the clock and the sifting
device to facilitate the flow of powder into the cup. Overflow
the cup until there is a cone of excess material.
16.3.2 After 3 min, carefully remove the excess powder by
passing the edge of a spatula blade parallel with, and in contact
with, the top of the cup. Move the spatula smoothly and keep
it level at all times to prevent packing or pulling the sample out
of the cup.
16.3.3 After the cup is level, lightly tap it with the edge of
the spatula to settle the powder. Wipe the outside of the cup
with a lintless cloth or paper towel. Avoid spilling the sample
while transferring the cup to the balance for weighing.
14
C 110
D 5 W/V
(5)
introduced by the interaction of the test material with soluble

liquid media.
19.1.3 This test method is suitable for screening material
from a nominal 300 m (50 mesh) in size to 20 m (635 mesh).
where:
D 5 packed density,
W 5 weight of sample, g, and
V 5 final volume of sample, cm3.
17.4.2 For reporting as pounds per cubic foot, multiply
grams per cubic centimetre by 62.43.
17.5.1 Single Operator PrecisionThe single operator
Therefore, results of two properly conducted tests by the same
operator on the same material should not differ by more than
1.4 lb/ft3.
17.5.2 Multilaboratory PrecisionThe multilaboratory
Therefore, results of two properly conducted tests from two
different laboratories on samples of the same material should
not differ by more than 4.8 lb/ft3.
17.5.3 The above precision statements are based on a
multilaboratory testing program for determination of the
packed bulk density of hydrated lime. No statement is made
regarding the precision of this method as it relates to other
materials. Due to a lack of a recognized industry standard, the
bias of this test method has not been determined.
NOTE 12Blinding of the sieves can occur at various sizes depending

on the materials being sieved. Experience has shown 45 m (325 mesh) to
be the lower limit with some hydrates. Other hydrates and pulverized
quicklime may be sieved to 32 m (450 mesh). Limestone can be sieved
to 20 m (635 mesh).
19.2 Apparatus:
19.2.1 An Enclosed Device, capable of creating a vacuum
on the backside of a sieve causing a rotating slit nozzle to
supply an air stream perpendicular to the bottom of the sieve.
The purpose is to suspend all material on the sieve by the air
stream on a rotating basis.20
19.2.2 Balance, suitable for weighing accurately to 0.01 g.
NOTE 13Selection of balance with regard to accuracy is dependent on
the sample size chosen and residue retained and must be consistent with
the accuracy required. Therefore, a balance weighing accurately to 0.001
g may be desired.
19.2.3 Brush, soft bristle.

19.2.4 Sieve CoverA hard plastic transparent cover used
to create a vacuum on the sieve.
19.2.5 Test SievesThe sieves should be constructed using
a woven wire, either brass or stainless steel, mounted on a
substantial frame. Electroformed sieves are not recommended
because of increased blinding and cleaning problems, making
them impractical to use under most conditions. The sieves shall
be approximately 8 in. in diameter and conform to Specification E 11. A flexible collar must be used to ensure an air tight
fit between the sieve and the device.
19.3 Procedure:
19.3.1 After placing the appropriate sieve into position,
weigh (to the nearest 0.01 g) a sample of the test material and
place it on the sieve.
18. Fineness of Pulverized Quicklime and Hydrated Lime

by Air Permeability
18.1.1 This test method covers the determination of fineness
of pulverized quicklime and hydrated lime using the Blaine air
permeability apparatus described in Test Method C 204. Fineness in terms of surface area shall be expressed as total surface
area in square centimetres per gram, or square metres per
kilogram.
18.1.2 This test method provides, in general, relative rather
than absolute fineness values. For the complete description of
the apparatus and the procedures for use, refer to Test Method
C 204.
18.2.1 Although precision for the test method for fineness of
portland cement by air permeability apparatus has been reported in Test Method C 204, the precision of this test method
has not been determined for pulverized lime and hydrated lime.
When sufficient data has been obtained and analyzed, a
statement of precision will be provided. In the meantime users
of this test method are advised to develop their own.
NOTE 14The amount of sample and duration of sieving are dependent

upon the type of material and gradation and therefore should be adapted
to individual conditions. Generally, the larger the sample size, the more
representative of the material tested and the less significant are errors of
technique, therefore, the results are the more exact. Sample weights can
vary from 20 g for material finer than 40 m up to 50 g for larger, heavier
materials.
19.3.2 Place cover on sieve, set timer to 6 min and start

vacuum (maintain vacuum according to manufacturers recommendation). Any material clinging to the cover or edge of the
sieve can be removed by light tapping with a mallet or similar
device (see Note 14). If agglomerations form, they can be
broken apart with a soft bristle brush.
19. Dry Screening of Hydrated Lime, Pulverized

Quicklime, and Limestone by Air Jet Sieving
19.1.1 This test method uses a rotating slit nozzle to supply
a stream of air directed at the backside of a test sieve, keeping
the screen from blinding. The aerated material is then pulled
back through the sieve by a vacuum source.
19.1.2 The advantages of dry screening by air jet sieving are
twofold. The material being tested is less likely to blind the
screen because of the recurring counterflow of an air stream to
the back of the sieve. Also, dry screening avoids the error
NOTE 15Static electrical charges can often develop on the cover (if it
is made of plastic) causing it to hold a heavy film of the material being
20
The apparatus describes commercially available units sold by the Alpine
American Corporation of Natick, Massachusetts. Although the description of the
apparatus is directed toward this commercially available equipment, it does not
restrict the use of other equivalent equipment which may be available or may be
constructed, as long as it follows the general principles outlined under the summary
of this test method.
15
C 110
20.4.8 Riffle Sample Splitter ,26 open pan, 12.7 mm (12 in.)
chute width.
20.4.9 Stopwatch.
20.5 Reagents and Materials:
20.5.1 Milling Solution, a 0.1 % solution of acrylate based
dispersant.27 The dispersant chosen should not increase the
solubility of limestone in water.28
20.6 Sampling:
20.6.1 Sample in accordance with Practice D 75.
20.6.2 Reduce the sample in accordance with Practice
C 702 and prepare by sieving out the material that passes a
850-m (No. 20) sieve29 and is retained on a 425-m (No. 40)
sieve.29
20.7 Procedure:
20.7.1 Weigh seven grinding media, make adjustments (by
substitutions or filing) to bring total weight to 160 g 6 1 g.
20.7.2 If the jar mill has provision for automatic shut-off, set
it for 5000 revolutions, otherwise determine the mill r/min by
counting the revolutions in an accurately timed period (using
stopwatch) and then calculate the exact time required for 5000
revolutions.
20.7.3 Weigh out 20 6 0.01 g of dried 20 by 40 mesh
limestone. Record actual weight as W1.
20.7.4 Add 180 mL of milling solution to clean and empty
mill jar.
20.7.5 Add the seven grinding media and quantitatively
transfer the limestone sample to the mill jar and secure the top.
20.7.6 Place the mill jar on the mill rollers and operate the
mill for the exact time required to make 5000 revolutions.
20.7.7 Quantitatively transfer the limestone slurry from the
jar mill by rinsing the entire contents onto a coarse sieve (for
example, 3.35 mm (No. 6)) and an underlying 75-m (No. 200)
sieve. Rinse the media and coarse sieve and separate the sieves.
20.7.8 Wet sieve the sample remaining on the 75-m (No.
200) sieve to remove the finer material.
20.7.9 Dry and weigh the residue from the 75-m (No. 200)
sieve and record as W2 (to the nearest 0.01 g).
20.8 Calculation:
20.8.1 Calculate the grindability index (GI) as follows:
sieved. If tapping will not loosen the material, a static face sheet21 may be
used to wipe the cover surface before starting the test.
19.3.3 After screening, clean the sieve with a fine bristle

brush being careful not to damage the mesh and then weigh the
residue to the nearest 0.01 g.
19.4 Calculation:
19.4.1 Calculate percent passing as follows:
@~S 2 R!/S# 3 100 5 percent passing
(6)
where:
S 5 sample weight, g, and
R 5 weight of sieve residue, g.
method.
20. Limestone Grindability Determination by the
Laboratory Ball Mill Method
20.1 Scope:
20.1.1 This test method is used to determine the relative
grindability or ease of pulverization of limestones of differing
hardness and to report this as a grindability index.
20.1.2 This test method is applicable to all types of limestone.
20.2 Summary of Test Method:
20.2.1 Limestone of a specified size range is wet ground in
a ball mill therein receiving a specified amount of grinding
energy. The amount of minus 75-m (200-mesh) limestone
produced is measured by wet sieving and reported as the
percent passing 75-m (200-mesh) after 5000 revolutions. This
is the grindability index.
20.3.1 This test method is useful for comparison and acceptance testing of limestone for applications where fine ground
limestone is desired.
20.4 Apparatus:
20.4.1 Jar Mill ,22 operated at 110 6 10 r/min.
20.4.2 Mill Jar ,23 ceramic 14 cm (512in.) diameter by 16.2
cm (634in.) high.
20.4.3 Grinding Media, 160 6 1 g total, consisting of seven
ceramic 21 by 21 mm (1316 by 1316 in.) cylindrical grinding
media24 (about 23 g each).
20.4.4 The sieves used shall conform to the requirements of
Specification E 11.
20.4.5 Weights and weighing devices, shall conform to the
requirements of Specification C 1005.
20.4.6 Drying Oven, capable of maintaining 100C.
20.4.7 A Chipmunk Crusher ,25 capable of breaking large
rocks to less than 6.35 mm (14 in.).
GI 5 ~W1 2 W2!/W1 3 100
(7)

20.9.1 The precision and bias of this test method has not
been determined at this time.
21. Specific Gravity of Hydrated Lime Products
21.1.1 This test method covers the determination of the
specific gravity of hydrated lime. The specific gravity of
hydrated lime is needed for calculations of air content (see
Section 13) and Blaine Surface Area.
21
Commercially available.
U.S. Stoneware No. 753-RM rotating mill, or equivalent, has been found
satisfactory for this purpose.
23
U.S. Stoneware mill jar No. 774-B-00, or equivalent, has been found
24
U.S. Stoneware burundum 1316in. grinding media, or equivalent, has been
found satisfactory for this purpose.
25
Bico-Braun Crusher (jaw, chipmunk) Model No. 241-34, or equivalent, has
been found satisfactory for this purpose.
22
26
Curtis Matheson Scientific Model No. 095-851, or equivalent, has been found
27
Alcosperse 149 from Alco Chemical Corp., or equivalent, has been found
28
Distilled or deionized water should be used for milling solution or solubility
tests.
29
U.S. Standard Sieves 6, 20, 40 and 200 mesh sizes; 20.3 cm (8 in.) diameter
by 5 cm (2 in.) depth with stainless steel wire cloth.
16
C 110
inclined position (Note 17), or gently whirl it in a horizontal
circle as to free the lime from air until no further air bubbles
rise to the surface of the liquid. If a proper amount of hydrated
lime has been added, the level of the liquid will be in its final
position at some point of the upper series of graduations. Take
the final reading after the flask has been immersed in the water
bath in accordance with 22.3.4.
21.4.4 Immerse the flask in a constant-temperature water
bath for sufficient periods of time in order to avoid flask
temperature variations greater than 0.2C between the intial
and final readings.
21.5 Calculation:
21.5.1 The difference between the first and the final readings
represents the volume of liquid displaced by the mass of
hydrated lime used in the test.
21.5.2 Calculate the hydrated lime density, p, as follows:
21.1.2 The specific gravity of hydrated lime is defined as the

mass of a unit volume of the solids.
21.2 Apparatus:
21.2.1 Le Chatelier FlaskThe standard flask, which is
circular in cross section with shape and dimensions conforming
essentially to Fig. 1 of Test Method C 188 (Note 16). The
requirements in regard to tolerance, inscription and length,
spacing, and uniformity of graduation shall be rigidly observed. There shall be a space of at least 10 mm between the
highest graduation mark and the lowest point of grinding for
the glass stopper.
21.2.1.1 The material of construction shall be best quality
glass, transparent and free of striae. The glass shall be
chemically resistant and shall have small thermal hysteresis.
The flasks shall be thoroughly annealed before being graduated. They shall be of sufficient thickness to ensure reasonable
resistance to breakage.
21.2.1.2 The neck shall be graduated from 0 to 1 mL and
from 18 to 24 mL in 0.1 mL graduations. The error of any
indicated capacity shall not be greater than 0.05 mL.
21.2.1.3 Each flask shall bear a permanent identification
number and the stopper, if not interchangeable ground, shall
bear the same number. Interchangeable ground-glass parts shall
be marked on both members with the standard-taper symbol
followed by the size designation. The standard temperature
shall be indicated, and the unit of capacity shall be shown by
the letters mL placed above the highest graduation mark.
p~Mg/m3 ! 5 p~g/cm3! 5
mass of hydrated lime ~g!

displaced volume ~cm3!
(8)
NOTE 19The displaced volume in milliliters is numerically equal to

the displaced volume in cubic centimeters.

method. When data is collected and analyzed, precision and
bias statements will be proposed.
22. Wet Sieve Analysis of Agricultural Liming Materials
22.1 Scope:
22.1.1 This test method covers the determination of gradation of an Agricultural Liming material by wash. Material finer
than 75 micormetres (No. 200) sieve will be removed from the
aggregate during the test, prior to dry sieving of the coarser
fraction.
22.1.2 The results of this procedure can be used to determine compliance to a particle size distribution relative to
applicable specifications for agricultural liming materials.
22.1.3 This method can not be used for the sieve analysis of
quicklime or materials containing quicklime, because of the
exothermic reaction with water.
22.2.1 Material finer than the 75 micrometres (No. 200)
sieve can be separated from larger particles more efficiently
and completely by wet sieving than through the use of dry
sieving. In sieving fine aggregate, the finer fractions can adhere
to the coarser fractions through a normal dry sieving operation.
Further, due to electrostatic charges, fine material can also
adhere to the coarser sieves. By removing the finer fractions
through the wash test, these problems are avoided. Therefore,
when an accurate determination of an agricultural liming
material is desired, this test method should be used.
22.2.2 The results of this test method are included in the
calculation of gradation, and the total amount of material finer
than 75 micrometres by washing, plus that obtained by dry
sieving the same sample, is reported with the results. Usually
the additional amount of material finer than 75 micrometres
obtained in the subsequent dry sieving process is a small
amount. If it is large, the efficiency of the washing operation
NOTE 16The design is intended to ensure complete drainage of the

flask when emptied, and stability of standing on a level surface, as well as
accuracy and precision of reading.
21.3 Reagents:
21.3.1 Ethyl Alcohol (Abolute), free of water, shall be used
in the density determination. The ethanol used should not have
been denatured with methanol.
21.4 Procedure:
21.4.1 Determine the specific gravity of hydrated lime on
the material as received, unless otherwise specified.
21.4.2 Fill the flask (Note 17) with denatured ethyl alcohol
to a point on the stem between the 0 and 1-mL mark. Dry the
inside of the flask above the level of the liquid, if necessary,
after pouring. Record the first reading after the flask has been
immersed in the water bath (Note 18) in accordance with
22.3.4.
NOTE 17It is advisable to use a rubber pad on the table top when
filling or rolling the flask.
NOTE 18Before the hydrated lime has been added to the flask, a loose
fitting lead-ring weight around the stem of the flask will be helpful in
holding the flask in an upright position in the water bath, or the flask may
be held in the water bath by a buret clamp.
21.4.3 Introduce a quantity of hydrated lime, weighed to the

nearest 0.05 g, (about 50 g for hydrated lime) in small
increments at the same temperature as the liquid (Note 17).
Take care to avoid splashing and see that the hydrated lime
does not adhere to the inside of the flask above the liquid. A
vibrating apparatus may be used to accelerate the introduction
of the hydrated lime into the flask and to prevent the lime from
sticking to the neck. After all the hydrated lime has been
introduced, place the stopper in the flask and roll the flask in an
17
C 110
should be checked. It could, also, be an indication of degradation of the material.
22.3 Apparatus and Materials:
22.3.1 BalanceA balance or scale readable and accurate
to 0.1 g or 0.1 % of the test load, whichever is greater, at any
point within the range of use.
22.3.2 SievesThe sieves shall be mounted on substantial
frames, either full height or extended, and constructed in a
manner that will prevent loss of material during sieving. The
sieves shall be of equal diameter and shape to allow for
nesting. The sieves shall conform to Specification E 11.
22.3.3 Sieve PanA pan of the same diameter as the sieves.
22.3.4 ContainerA pan or vessel of a size sufficient to
contain the sample covered with water and to permit vigorous
agitation without loss of any part of the sample or water.
22.3.5 OvenAn oven of sufficient size, capable of maintaining a uniform temperature of 110 6 5C.
NOTE 22If mechanical washing equipment is used, the charging of

water, agitating, and decanting may be a continuous operation.
22.5.4 Return all material retained on the nested sieves by

flushing to the washed sample. Dry the washed material to
constant mass at a temperature of 110 6 5 C and determine
the mass to the nearest 0.1 g. Calculate the amount of material
passing a 75 micrometre sieve by washing according to 22.6.1.
22.5.5 Select the sieves of a suitable size as desired or
required by specification and those sieves necessary to regulate
the amount of material between the various screens. Nest the
screens in order of decreasing size of opening, from top to
bottom, on a sieve pan. Be sure to nest the 75 micrometre sieve
just above the pan. Place the dried sample on the top sieve.
Shake the nested sieves briskly or by use of a mechanical
device for a sufficient period to assure that the sample has been
adequately screened (see Note 23).
NOTE 23To be adequately screened, no more than 1 % of the residue
on any individual sieve will pass that sieve during 1 min. of continuous
sieving. For a more detailed explanation refer to C 136-84a, paragraph
7.4.
NOTE 20The use of a mechanical apparatus to perform the washing

operation is not precluded, provided the results are consistent with those
obtained using manual operations. The use of some mechanical washing
equipment with some samples may cause degradation of the sample.
22.5.6 The amount of material on an eight inch sieve after

shaking is limited to approximately 200 g, so that all particles
during a test have access to the screen medium (see Note 24).
If the amount remaining on a sieve is greater than 200 g, the
sieve analysis must be repeated. Place an intermediate sieve
between the overloaded sieve and the one nested above.
22.4 Sampling:
22.4.1 Since sampling is equally as important as testing, it is
critical that samples be obtained that are representative of the
materials being investigated. Therefore, sampling must be
conducted in as conscientious a manner as possible. Incremental sampling should be employed, combining the increments
into one bulk sample.
22.4.2 Use the procedures described in Practice C 50, or
Practice D 75.
22.4.3 To reduce the bulk sample to the amount needed for
testing, the use of mechanical splitters or the process of
quartering must be used. At no time can a random lot be drawn
from the bulk sample for testing.
22.5 Procedure:
22.5.1 Dry the test sample to constant mass at a temperature
of 110 6 5C. Determine the mass to the nearest 0.1 % of the
mass of the test sample. The amount of sample required for this
test shall be between 200 to 400 g. The test sample shall be the
end result of the reduction. Reduction to an exact predetermined mass shall not be permitted.
22.5.2 After drying and determining the mass, place the test
sample in the container and add sufficient water to cover it.
Agitate the sample with sufficient vigor to result in complete
separation from the coarser particles of all particles finer than
the 75 micrometre sieve from the coarser particles, and to bring
the fine material into suspension. Immediately pour the wash
water containing the suspended and dissolved solids over the
nested sieves (see Note 21), arranged with the coarser sieve on
top. Take care to avoid, as much as feasible, the decantation of
coarser particles of the sample.
NOTE 24A twelve inch screen can be used, but the amount of material
retained on a sieve is limited to 6 kg/m2.
22.5.7 Record the weight of material from each size increment and the sieve pan by weighing on a balance to the nearest
0.1 g (see Note 25). Total the retained masses of all the size
increments and the sieve pan from the dry sieve test. If this
amount differs from the dry mass of the sample after washing
by more than 0.3 %, the results should not be used for
acceptance purposes.
NOTE 25A soft bristle can be used to help remove material from
sieves, but at no time can material be forced through a sieve.
22.6 Calculation:
22.6.1 Calculate the amount of a material passing a 75
micrometre sieve by washing as follows:
A 5@~B C! / B# 3 100
(9)
where:
A 5 percentage of material finer than a 75 micrometre sieve
by washing,
B 5 original dry mass of sample, g, and
C 5 dry mass of sample after washing, g.
22.6.2 Calculation of amount of material passing individual
sieves follows:
22.6.2.1 Add weight of material finer than a 75 micrometre
sieve by washing (B C, in 22.6.1) to the weight of material
finer than a 75 micrometre sieve obtained in the dry screening,
if washed.
22.6.2.2 Calculate the percent retained on each sieve and the
pan as follows:
NOTE 21It is recommended that a #16 mesh sieve or one of

approximate size be used to nest on top of the # 200 mesh sieve for
protection from the sample.
22.5.3 Add a second charge of water to the sample in the

container, agitate, and decant as before. Repeat this operation
until the wash water is clear (see Note 22).
A 5~B / C! 3 100
18
(10)
C 110
22.7.1 The precision and bias of this method has not been
determined by this subcommittee at this time. For precision
and bias data from similar methods refer to Test Method C 117
and Test Method C 136.
where:
A 5 percentage of material retained on each sieve (pan),
B 5 dry mass of sample, g, retained on each sieve (pan),
and
C 5 original dry mass of sample, g.
22.6.2.3 Calculate the cumulative percent retained for each
screen by adding the percentage retained on that sieve and all
sieves of larger diameter opening.
22.6.2.4 For each screen, subtract the cumulative percent
retained from 100 to obtain the percent passing.
23. Keywords
23.1 apparent density; dry brightness; dry screening; fineness; lime putty; limestone grindability; particle size; slaking
rate
The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection
with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such
patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM Headquarters. Your comments will receive careful consideration at a meeting of the responsible
technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your
views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above address or at
610-832-9585 (phone), 610-832-9555 (fax), or [email protected] (e-mail); or through the ASTM website (www.astm.org).
19

C0110 00

Uploaded by

Copyright:

Available Formats

C0110 00

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

C0110 00

Uploaded by

Copyright:

Available Formats

Designation: C 110 00

Standard Test Methods for

Physical Testing of Quicklime, Hydrated Lime, and

C 25 Test Methods for Chemical Analysis of Limestone,

1.2 The test procedures appear in the following order:

1.3 The values stated in SI units are to be regarded as the

Annual Book of ASTM Standards, Vol 04.01.

5.2.5 Attach a pressure gage to the water faucet and a rubber

Annual Book of ASTM Standards, Vol 14.02.

NOTE 2Most lime hydrates will require 250 to 300 mL of water to

6.3.2 Mechanical Mixing Procedure Using the Hobart N-50

FIG. 1 Modified Vicat Apparatus

Constants of the Machine:

NOTE 4A convenient apparatus for determining the rate of absorption

FIG. 2 Emley Plasticimeter

7.3 Plasticity Determination:

7. Plasticity of Lime Putty

Standard portland cement

Blend the mix until homogeneous.

8. Autoclave Expansion of Hydrated Lime

9. Popping and Pitting of Hydrated Lime

10. Water Retention of Hydrated Lime

Blend the mix until homogeneous.

This ability, measured as a percent of the original consistency,

FIG. 3 Apparatus Assembly for the Water Retention Test

leaks and to determine that the required vacuum is obtained.

NOTE 5Slight variations in results of this test method on a sample run

11.4 Precision and Bias:

FIG. 4 Slaking Reactivity Apparatus

mm (No. 6) sieve as possible. It is not necessary that 100 % of

FIG. 5 Stirring Rod Detail

stem extending through the lower slot. The apparatus may be

TABLE 1 Schedule for Slaking Rate

curve showing temperature rise as the ordinate and time as the

TABLE 4 Weight of Materials for Mortar Batch

density of air-free mortar,

NOTE 6For lime/sand mortars, W1 and S1 should be dropped from the

13.6 Precision and Bias:

TABLE 2 Precision Data

13. Air Entrainment

14. Particle Size of Pulverized Limestone

14.4.6 Take additional readings at 15, 30, 60, 120, or 180

Available from Taylor Instrument Co., Catalog No. 22297.

FIG. 6 Composite Correction Factor for Hydrometer

14.5.12 The values of Dc are now plotted against the values

DD in terms of =L/T . Multiply by DT (DT is the difference

15.5.2.2 The Eastman Kodak barium sulfate reflectance

15.6.4 After the reflectometer has been standardized, the

15.3.1 Reflectometer :17

NOTE 10It is recognized that there are various manufacturers of

16. Apparent Loose Density of Hydrated Lime,

FIG. 7 Values for

=L/T as Related to Lfor Given Values of T (Time)

16.2.2 Density Cup, 400 mL cylindrical cup as described in

NOTE 1Calculate to nearest 0.1 of Rc. For a reading of 24.7, take

16.5.3 The above precision statements are based on a

FIG. 8 Dry-Powder Press

introduced by the interaction of the test material with soluble

NOTE 12Blinding of the sieves can occur at various sizes depending