Wcdma Bts3900 HW

Internal
WCDMA BTS3900
Hardware Structure
BTS3900V200R010
WRAN Training Team
HUAWEI TECHNOLOGIES CO., LTD.
All rights reserved
www.huawei.com
As an important part of UTRAN,
NodeB mainly processes the signals of

physical layer of Uu interface
BTS3900 is a new generation indoor
marco NodeB which is produced by

Huawei Co. Ltd.
All rights reserved
Page 2
Upon completion of this course, you will be able to:

Master the hardware structure of BTS3900
Master the working principle of different subsystems and

boards of BTS3900
Master the cables connection rules of BTS3900
Know typical configurations of BTS3900
All rights reserved
Page 3
BTS3900 Product Description

BTS3900 Hardware Description
All rights reserved
Page 4
Chapter 1 NodeB Overview

Chapter 2 BTS3900 Hardware Structure
Chapter 3 BTS3900 Typical Configuration
All rights reserved
Page 5
Abbreviations
WMPT
WCDMA Main Processing and Transmission Unit
WBBPa
WCDMA Baseband Process unit Type A
WRFU
WCDMA Radio Filter Unit
UBFA
Universal BBU Fan Unit Type A
UEIU
Universal Environment Interface unit
UELP
Universal E1/T1 Lighting Protection unit
UFLP
Universal FE/GE Lighting Protection unit
UPEU
Universal Power and Environment Interface Unit
UAEU
Universal ATM over E1/T1 Interface and Processing Unit
UIEU
Universal IP Packet over E1/T1 Interface and Processing Unit
UTRP
Universal Transmission Processing Unit
DCDU-01
Direct Current Distribution Unit-01
CPRI
Common Protocol Radio Interface
PSU
The power supply unit
PMU
The power and environment monitoring unit
APM
Advanced Power Module
All rights reserved
Page 6
NodeB Position in UMTS Network

UTRAN
UE
Uu
CN
Iu
Iu-CS
RNC
Iub
Iu-BC
CS
NodeB
Iu-PS
Iur
PS
NodeB
Iu-BC
Iub
NodeB
RNC
CBC
All rights reserved
Page 7
NodeB System Architecture

Clock synchronization source
Uu
UE
Antenna & feeder

subsystem
GPS antenna & feeder system
Internal Clock
RNC
Iub
BTS3900 cabinet
DDF
power supply
system
Transmission
device
Environment
Monitoring
device
O&M terminal
BTS3900 System
All rights reserved
Page 8

All rights reserved
Page 9

Section 1 BTS3900 Introduction
Section 2 BBU Modules Structure
Section 3 RF Modules Structure

Section 4 Power Modules Structure
Section 5 BTS3900 Cables
All rights reserved
Page 10
BTS3900 Appearance
Type
Parameters
Dimensions
600(W)*900(H)*450(D)
Empty cabinet
70kg
Weight under full

configuration
160Kg
3*1 and 3*2 Weight
120Kg
- 48V : Input range of

voltage
-38.4V DC to -57V DC
+24V: Input range of

voltage
+21.6 V DC to +29 V DC
200 V AC to 240 V AC
200 V AC to 240 V AC 176 V AC to

290 V AC, single-phase
200 V AC/346 V AC to
240 V AC/415V AC
176 V AC/304 V AC to 290 V AC/500

V AC, three-phase
Working Temperature
-20+50
All rights reserved
Page 11
BTS3900 Single Cabinet Full Configuration Structure

1U
9U
19U
2U
1U
1U
2U
1U
2U
- 48VDC
Single Cabinet
220V AC
Single Cabinet
+ 24VDC
Single Cabinet
All rights reserved
Page 12
BTS3900 Stacked Cabinets Full Configuration Structure
3U
All rights reserved
Page 13
BTS3900 Capacity and Characteristics

System capacity specifications:
BTS3900 can support up to: uplink 1536 CEs and downlink 1536 CEs
BTS3900 can support up to: 3*8 cells or 6*4 cells

Characteristics
Transmission Type: E1/T1, FE (electrical port ), FE (optical port ),
Networking mode: star, chain, tree, ring and hybrid

Synchronization clock sources: Iub interface clock, GPS, and internal clock
Handover types: softer handover, soft handover and hard handover
Services: CS services, PS services , mixed services and position services
Enhanced functionsRET , HSDPA , HSUPA phase II
All rights reserved
Page 14
BTS3900 Logical Structure

-48V
+24V/220V
Power
Module
PSU
DCDU
WRFU
Iub
BBU
RNC
WRFU
Baseband Transmission
Control module
Signal
RF Module
Current
All rights reserved
Page 15
Antenna


All rights reserved
Page 16
Logical Structure of the BBU3900 Module

OMC
External Subsystem
Control Subsystem
Clock mode
Operation&
Maintenance
Signaling
Processing
Decoding
Transmission
Adaptation
Protocol
Processing
FP Processing
RNC
E1/T1
FE
Transport
Interface
Demodulation
Power
Control
information
Codling
Transport Subsystem
Power mode
Modulation
Baseband Subsystem
All rights reserved
Page 17
Interface
CPRI
TO WRFU
Module
BBU3900 Module Introduction

Full configuration
Typical configuration
Mandatory boards and modulesWMPT, WBBP, UBFA, and UPEU
The optional boards are the UELP, UFLP, UTRP, and UEIU.
All rights reserved
Page 18
BBU3900 Module Introduction

Slot
SLOT0
SLOT4
16
SLOT1
SLOT5
SLOT2
SLOT6
SLOT3
SLOT7
Slot 18
Slot 19
WBBP
UTRP
PEU/
WBBP
UTRP
EIU
WBBP
WMPT
PEU/
WBBP
WMPT
EIU
Active and standby slot definition

only for UTRP board
Board
Slot 0
Slot 1
Slot 2
Slot boards definition
Slot 3
Slot 4
Slot 5
WMPT
UTRP
available
available
available
available
available
available
WBBP
available
available
available
available
available
available
UELP
available
available
UFLP
available
available
All rights reserved
Page 19
Slot 6
Slot 7
available
available
BBU Module --- WMPT Board

IP transmission on
Electrical Port :RJ45
Loading
Testing:USB
GPS antenna: SMA
LEDs
Commissioning:RJ45
Board number
IP transmission
Optical signals: SFP
4E1:DB26
Main Functions
maximum is 2 for one BBU
Providing OM functions
mandatory board
Controlling other boards in the system and
working in active and

standby
providing the reference clock

Providing USB ports for automatic NodeB
upgraded
Providing transmission port for Iub interface
Providing OM channels
All rights reserved
Page 20

LEDs of running status of WMPT:
Label
Color
Status
Description
RUN
Green
ON
The board has power input, yet the board is faulty.
OFF
The board has no power input.
1s ON, 1s OFF
The board is running as configured.
0.125s ON, 0.125s OFF
The software is being loaded to the board, or the

board is not in use.
ON
The board is reporting hardware alarms.
OFF
The board is running properly.
ON
The board is in active mode.
OFF
The board is in standby mode.
ALM
ACT
Red
Green
All rights reserved
Page 21
LED
Color
Status
Description
LEDs beside the

FE1 and FE0 optical
port
Green
ON
The connections are functional.
OFF
The connections are faulty.
Blinking
There is ongoing data transmission.
OFF
There is no data transmission.
ON
The connections are functional.
OFF
The connections are faulty.
Blinking
There is ongoing data transmission.
OFF
There is no data transmission.
Yellow
LEDs beside the

ETH port
Green
Yellow
All rights reserved
Page 22

Two DIP Switches :
SW1 for setting the E1/T1 working mode

SW2 for setting the protection ground for the E1.
Settings of SW1
Bit
T1 Mode
120-ohm E1
Balanced Mode
75-ohm E1
Unbalanced Mode
ON
OFF
ON
ON
OFF
ON
OFF
ON
ON
OFF
ON
ON
Settings of SW2
Bit
120-ohm E1
Balanced Mode
75-ohm E1
Unbalance
d Mode
OFF
ON
OFF
ON
OFF
ON
OFF
ON
All rights reserved
Page 23
Description
The RRING is for

connected to the
protection ground
BBU Module --- WBBPa Board

CPRI 0~2 (1.25G-2.5G): SFP
LEDs
Board number mandatory board, maximum is 6

Main Functions
Providing the CPRI interface for communication between the BBU and the
WRRU or WRFU
Processing uplink and downlink baseband signals and support HSUPA and
HSDPA function
Supporting 1+1 backup of the CPRI interface

According to the board chip processing capability, WBBP module include
seven specifications. Current WBBP is the A version, called WBBPa.
All rights reserved
Page 24
BBU Module --- WBBPa Board

LED of running status of board :
Label
Color
Status
Description
RUN
Green
ON
OFF
The board has no power input or is faulty.
1s ON, 1s OFF
0.125s ON/OFF
Software is being loaded to the board.
ON
OFF
The board is not in use.
OFF
ON
The board has alarms on hardware and it should be replaced with a new one.
OFF
normal
ON
The CPRI links over the optical cable are faulty.
Blinking at 2 Hz
The RRU on the CPRI link is faulty in hardware.
Blinking at 0.5 Hz
The RRU on the CPRI link is faulty in the antenna system connection.
ACT
ALM
CPRI0
CPRI1
CPRI2
Green
Red
Red
Green
All rights reserved
Page 25
BBU Module --- WBBP Board

There are 2 kinds of Baseband card, WBBPa and WBBPb.
The WBBPa support HSDPA (2 ms TTI) and support for HSUPA phase I (10 ms TTI).
The WBBPb support HSDPA (2 ms TTI), and support for HSUPA phase II (2 ms TTI).
Board
Uplink R99
Downlink
HSDPA
HSUPA
Type
Cell
/HSUPA CE
R99 CE
HSDPA Capacity
throughput
throughput
WBBPa
3 cells
128
256
45 HS-PDSCH codes
15Mbps
6Mbps
WBBPb1
3 cells
64
64
45 HS-PDSCH codes
15Mbps
6Mbps
WBBPb2
3 cells
128
128
45 HS-PDSCH codes
15Mbps
6Mbps
WBBPb3
6 cells
256
256
90 HS-PDSCH codes
30Mbps
12Mbps
WBBPb4
6 cells
384
384
90 HS-PDSCH codes
30Mbps
12Mbps
All rights reserved
Page 26
BBU Module --- UBFA Board
Board number mandatory board, maximum is 1

Main Functions
Controlling the fan speed

Reporting the fan status to the WMPT
Detecting the temperature of the fan board

Label
Color
Status
Description
STATE
Green
0.125s ON,
The module is not registered, and no
0.125s OFF
alarm is reported.
1s ON, 1s OFF
ON
The module is reporting alarms.
Red
All rights reserved
Page 27
BBU Module --- UPEU Board

Panel of the UPEA
Panel of the UPEB
+24V to +12V
-48V to +12V
Board number mandatory, maximum is 2, 1+1 backup

Main Functions
Converting -48 V or +24 V DC power input to +12 V DC power that is supported

by boards
Reporting alarms related to input and output under voltage
Providing transmission ports for RS485 signals and 8 dry contact alarm signals
All rights reserved
Page 28
BBU Module --- UPEU Board

LED: The UPEU has one LED, indicating the running status of the board.
Label
Color
Status
Description
RUN
Green
ON
OFF
The board has no power input, or

the board is faulty.
Socket and Port: The UPEU has one socket and four ports.
Label
Quantity
Connector Type
Function
PWR
3V3
DC power input
EXT-ALM1
RJ45
Transmitting dry contact alarm signals
EXT-ALM0
RJ45
MON1
RJ45
MON0
RJ45
Transmitting RS485 environment

monitoring signals
All rights reserved
Page 29
BBU Module --- UTRP Board
The UTRP provides ports for eight E1s/T1s and implements transport such as IP and
ATM between the BBU3900 and the RNC.
4 E1:DB26
Label
Color
Status
Description
RUN
Green
ON
OFF
The board has no power input or is faulty.
1s ON, 1s OFF
0.125s ON, 0.125s OFF
Software is being loaded to the board.
2s ON, 2s OFF
The board is under test.
ON
The board is in active mode.
OFF
The board is in standby mode.
OFF
ON
The board is reporting alarms and is faulty.
ACT
ALM
Green
Red
All rights reserved
Page 30
BBU Module --- UTRP Board Type

WCDMA UTRP extend transmission board
UTRP board should add sub board to provide the different interface type.
WD22UTRP is the main board name. The UTRP has three sub-boards in current version
UAEU: Eight ATM over E1s/T1s
UIEU: Eight IP over E1s/T1s
UUAS: One unchannelized ATM over SDH/SONET(STM-1/OC-3) interface
The board in
gray
table is not
be delivered
currently.
Transmission
Sub
board
Interface
type
Board name
name
Interface specification
WD22UEEU
WD22UEEC
FE/GE electrical board
2*FE/GE (10/100/1000M
adaptive)
WD22UEOU
WD22UEOC
FE/GE optical board
2*FE/GE (10/100/1000M
configurated)
WD22UAEU
WD22UAEC
E1/T1 ATM interface sub board
8* E1/T1
WD22UIEU
WD22UPEC
E1/T1 IP interface sub board
8*E1/T1
WD22UCPU
WD22UCPS
Channelization IP optical sub board
1*STM-1
WD22UUPU
WD22UUPS
Unchanneliazation IP optical sub board
1*STM-1
WD22UCAU
WD22UCAS
Channelization ATM optical sub board
1*STM-1
WD22UUAU
WD22UUAS
Unchanneliazation ATM optical sub board
1*STM-1
All rights reserved
Page 31
BBU Module --- UEIU Board

Board number: maximum is 1
The UEIU Functions
Connecting to an external monitoring device and transmitting RS485

signals to the WMPT
Connecting to an external alarm device and transmitting dry contact alarm

signals to the WMPT
Port : The UEIU has four ports.
Label
Connector Type
MON0
RJ45
MON1
RJ45
EXT-ALM0
RJ45
EXT-ALM1
RJ45
All rights reserved
Page 32
BBU Module --- SLPU Board

UFLP
The auxiliary devices of the
UELP
BBU3900. The devices are
the SLPU, UELP, and UFLP

SLPU: The signal lightning
protection unit is an optional

module of the BTS3900
cabinet (-48 V) or the power
distribution cabinet.
The UFLP and the UELP
are optional units that are

installed in the SLPU.
All rights reserved
Page 33
BBU Module --- UELP Board

UELP: The universal E1/T1 lightning protection (UELP) unit is a universal E1/T1
The UELP can be optionally installed in the SLPU or the BBU. Each UELP
supports the surge protection of 4-way E1/T1 signals.
DB26
DB25
E1 Connection:
E1
E1
Indoor DDF
All rights reserved
Page 34
BBU Module --- UELP Board

DIP Switch: The UELP has one DIP switch, which is used to select whether the
receive terminal is grounded. The DIP switch has four bits.
DIP
Switch
S1
DIP Status
Description
ON
ON
ON
ON
Used for the 75

unbalanced mode
OFF
OFF
OFF
OFF
Used for other

modes except the 75
unbalanced mode
All rights reserved
Page 35
BBU Module --- UFLP Board

UFLP: The universal FE lightning protection (UFLP) board is optionally installed in the
SLPU or BBU. Each UFLP supports 2-way FE surge protection.
IP Cable Connection.
Transmission Equipment
LAN switch or Router
All rights reserved
Page 36


All rights reserved
Page 37
RF Module --- WRFU Board
The WRFU consists of the high-speed interface unit, signal processing unit,
power amplifier, and duplex unit
All rights reserved
Page 38

Type
Label
Connector Type
Description
Port for
transceiving RF
signals
ANT-RXB
DID connector
Connecting the antenna

subsystem
ANT-TX/RXA
DID connector
CPRI
CPRI0
SFP female
connector
Connecting the BBU, or

the upper-level WRFU
during the cascading
CPRI1
SFP female
connector
Connecting the lowerlevel WRFU during the

cascading
RX-INB
QMA female
connector
Input port of diversity

signals in the antenna
channel
RX-OUTA
QMA female
connector
Output port of diversity

signals in the antenna
channel
Power port
PWR
3V3 power
connector
Introducing power
Commissioning port
MON
RJ45 connector
Used for commissioning
Interconnection port
for RF receive
signals
All rights reserved
Page 39

Identifier
Status
Meaning
RUN
On
The power input is normal, but the module is faulty.
Off
There is no power input, or the module is faulty.
On for 1 second and off for 1 second
The module is functional.
On for 0.125 second and off for 0.125

second
The module is loading software or is not started.
On
The module is in the alarm status.
Off
No alarm is generated.
On
The module is functional and is connected to the BBU.
Off
The module is not connected to the BBU.
On for 1 second and off for 1 second
The module is in the local test status.
Off (red)
No VSWR alarm is generated.
On (red)
A VSWR alarm is generated.
On (green)
The CPRI link is normal.
On (red)
The interface module fails to receive signals.
Red LED on for 1 second and off for

1 second
The CPRI link is out of lock.
ALM
ACT
VSWR
CPRI0
CPRI1
All rights reserved
Page 40

RF specifications:
One WRFU supports four carriers

Each carriers maximum output power of WRFU is 80W
The receive sensitivity of single antenna is better than -125.8dBm
The receive sensitivity of two antennas is better than -128.6dBm
The maximum searching ability is 200km

The maximum access search radius is configurable with the step size of 300 m
Configuration Type (No
Transmit Diversity)
Transmit Diversity
Power (W)/Carrier
Typical Power
Consumption (W)
Maximum Power
Consumption (W)
3*1
20
520
630
3*2
20
610
830
3*3
20
810
1070
3*4
20
1020
1330
All rights reserved
Page 41


All rights reserved
Page 42
Power Distribution Modes of the BTS3900
- 48 V DC Distribution
All rights reserved
Page 43

+24 V DC Distribution
All rights reserved
Page 44

220 V AC Distribution
All rights reserved
Page 45
- 48V Cabinet Power Module --- DCDU-01 Board

Function
The DCDU-01 supports one -48 V

DC power input and ten -48 V DC
power outputs
The DCDU-01 supplies power to
the BBU, WRFU, FAN, and user
devices inside cabinets
The DCDU-01 has the built-in
surge protector, which supports
the surge protection capability of
the differential mode of 10 kA and
the common mode of 15 kA
- 48V DC
Single Cabinet
All rights reserved
Page 46
- 48V Cabinet Power Module --- DCDU-01 Board

Name
Label
Description
Power input
NEG(-)
-48 V NEG input wiring terminal
RTN(+)
-48 V RTN input wiring terminal
SPARE2, SPARE1,
RFU0 to RFU5 supplying power to six WRFUs
BBU, FAN, and RFU5-
BBU supplying power to the BBU
RFU0
FAN supplying power to the FAN
wiring terminal
Power output port
SPARE1 and SPARE2 reserved

Power switch
SPARE2, SPARE1,
BBU, FAN, and RFU5RFU0
RFU0 to RFU5 controlling the ON/OFF of the current of

six WRFUs
BBU controlling the ON/OFF of the current of the BBU
FAN controlling the ON/OFF of the current of the FAN
SPARE1 and SPARE2 controlling the ON/OF of the
current on the SPARE1 and SPARE2 power output ports
Alarm output port
SPD ALM
DUDU-01 dry contact alarm output port

All rights reserved
Page 47
+24V Power Subrack --- PSU (DC/DC) Board

Function
Converting +24 V DC power to -48 V DC power and leading the -48 V DC power
to the DCDU
Monitoring alarms related to module faults ,alarms related to module protection
and power out-of-position alarm
(1) Power running LED

(2) Protection LED
(3) Fault LED
+ 24V DC Single Cabinet

All rights reserved
Page 48
220V AC Power Subrack --- PSU(AC/DC) Board

Function
The power subrack consists of the PMU, PSU (AC/DC) and the wiring unit of the
power subrack (220 V).
The power subrack (AC/DC) converts the 220 V AC power to the -48 V DC power.
(1) Power running LED
(2) Protection LED

(3) Fault LED
220V AC Single Cabinet
All rights reserved
Page 49
220V AC Power Subrack --- PSU(AC/DC) Board

LED
Color
Status
Meaning
Power
running
LED
Green
On
Normal
Off
There are faults (such as no AC input, or overvoltage and

undervoltage of AC input) on the mains, or the PSU has no output.
Protection
LED
Yellow
Off
Normal
On
Temperature pre-alarm or fan pre-alarm
Off
Normal, or the PSU has no output because of faults (such as no AC

input, or overvoltage and undervoltage of AC input) on the mains.
On
There is no output because of output overvoltage shutdown, fan

fault, overtemperature shutdown, remote shutdown, or internal
problems of the PSU.
Fault LED
Red
All rights reserved
Page 50
220V AC Power Subrack --- PMU Board

The power and environment monitoring unit (PMU) is the unit for monitoring the
power and the environment. The PMU provides perfect power system management,
power distribution detection, and alarm report functions.
(1) LEDs
(2) Power supply

test ports
(3) RS232/RS422 port
(4) Battery control

switches
(1) Backplane port
(2) DIP switch
(5) COM port

All rights reserved
Page 51

Identifier
Color
Status
Meaning
RUN
Green
On for 1 second and
The module is functional, and the communication with the
off for 1 second
main control unit is normal.
On for 0.125 second
The module runs normally but the communication with the
and off for 0.125
main control unit fails.
second
If the PMU does not communicate with the main control unit
for one minute, the communication fails. In this situation, the
RUN LED blinks four times every second.
ALM
Red
On/Off
The PMU is faulty (not in the power-on self-check state).
On
The following alarms are reported:

Mains overvoltage or undervoltage alarm
Busbar overvoltage or undervoltage alarm
Power module alarm
Load shutdown alarm
Off
No alarm is generated.
All rights reserved
Page 52

Port
Purpose
RS232/RS422 port
Communicating with the main control unit
Battery control
The battery control switch has two control ports ON and OFF, which are
switch
used for powering on and off the battery.

Press and hold the port ON for 5s to 10s until the battery is powered on.
Press and hold the port OFF for 5s to 10s until the battery is powered off.
CAUTION:
You need to insert a small round bar into the hole when you operate the
battery control switch. When you hear a crack, the battery is powered on or
off.
To operate the battery control switch on the front panel of the PMU, insert
a small round pole into the hole.
Power supply test
Two power supply test holes -48 V and 0 V are available for measuring
port
power voltages through an ordinary multimeter.
COM port
Connecting the external signal transfer board
Backplane port
Connecting the backplane
All rights reserved
Page 53
DIP Switch: The DIP switch is

located on the rear panel of the
PMU. The DIP switch has eight
bits, which are set to OFF before
delivery.
Bit 3
Bit 2
Bit 1
Bit 0
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
All rights reserved
Monitoring Address
Page 54
FAN Unit
The FAN unit refers to the fan box. The FAN unit provides the functions of ventilation
and heat dissipation for cabinets. One FAN unit has four independent fans.
Type
Label
Connector Type
Description
Power port
-48 V
3V3 power connector
Introducing the -48 V

DC power
Temperature sensor port
SENSOR
RJ45 connector
Connecting the
external temperature
sensor
Communication port
COM OUT
RJ45 connector
Cascading the lowerlevel FAN module
COM IN
RJ45 connector
Connecting the main

control unit
All rights reserved
Page 55


All rights reserved
Page 56
BBU3900 Cable Connection
All rights reserved
Page 57
Cables --- PGND Cable

PGND Cable
OT terminal
Name
Color
Cross-Sectional Area
PGND cable of the

BTS3900 WCDMA cabinet
Green and yellow
The cross-sectional area of a wire is 25

mm2.
PGND cable of the DCDU
Green and yellow

mm2.
PGND cable for the SLPU
Green and yellow

mm2.
Front door PGND cable
Green and yellow

mm2.
All rights reserved
Page 58
Cables --- Power Cable

Power Cable Between the DCDU,BBU,FAN and WRFU
All rights reserved
Page 59
Cables --- Transmission Cable
E1 Cable
FE Cable
E1 Surge Protection Transfer Cable
FE Surge Protection Transfer Cable
All rights reserved
Page 60
Cables --- CPRI Cable

This describes the CPRI electrical cable. It helps to implement high speed
communication between the BBU3900 and the WRFU.

Appearance : The CPRI electrical cable is an SFP high speed transmission
cable that has a SFP200 male connector at each end.
One End
The Other End
CPRI port on the WBBP
CPR10 port on the WRFU
All rights reserved
Page 61

All rights reserved
Page 62
Configuration Types of the BTS3900

The BTS3900 supports omni-directional, 2-sector, 3-sector, and 6-sector
configurations. It also supports smooth capacity expansion from 1x1 to 3x8.

This part illustrates the configuration type of the BTS3900 by taking the WBBPa
supporting three cells and the WRFU supporting the 80W/4 carrier as an example.
All rights reserved
Page 63
Thank You
www.huawei.com

Wcdma Bts3900 HW

Uploaded by

Copyright:

Available Formats

Wcdma Bts3900 HW

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Wcdma Bts3900 HW

Uploaded by

Copyright:

Available Formats

Internal

HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

As an important part of UTRAN,

NodeB mainly processes the signals of

marco NodeB which is produced by

HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

Upon completion of this course, you will be able to:

Master the working principle of different subsystems and

Know typical configurations of BTS3900

HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

BTS3900 Product Description

HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

Chapter 1 NodeB Overview

HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

WCDMA Main Processing and Transmission Unit

WCDMA Baseband Process unit Type A

WCDMA Radio Filter Unit

Universal BBU Fan Unit Type A

Universal Environment Interface unit

Universal E1/T1 Lighting Protection unit

Universal FE/GE Lighting Protection unit

Universal Power and Environment Interface Unit

Universal ATM over E1/T1 Interface and Processing Unit

Universal IP Packet over E1/T1 Interface and Processing Unit

Universal Transmission Processing Unit

Direct Current Distribution Unit-01

Common Protocol Radio Interface

The power supply unit

The power and environment monitoring unit

Advanced Power Module

HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

NodeB Position in UMTS Network

HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

NodeB System Architecture

Antenna & feeder

GPS antenna & feeder system

HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

Chapter 1 NodeB Overview

HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

Chapter 2 BTS3900 Hardware Structure

Section 3 RF Modules Structure

HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

HUAWEI TECHNOLOGIES CO., LTD.

Weight under full

3*1 and 3*2 Weight

- 48V : Input range of

+24V: Input range of

200 V AC to 240 V AC 176 V AC to

176 V AC/304 V AC to 290 V AC/500

31 and 32 Weight

BTS3900 can support up to: 38 cells or 64 cells