The document provides specifications for a Link-Belt RTC-8065 telescopic boom rough terrain crane with a 65-ton capacity. It includes dimensions, engine details, hydraulic system components, load hoisting system capabilities, and descriptions of the carrier, suspension, and axles. Capacities for the crane are listed in a separate section.
The document provides specifications for a Link-Belt RTC-8065 telescopic boom rough terrain crane with a 65-ton capacity. It includes dimensions, engine details, hydraulic system components, load hoisting system capabilities, and descriptions of the carrier, suspension, and axles. Capacities for the crane are listed in a separate section.
The document provides specifications for a Link-Belt RTC-8065 telescopic boom rough terrain crane with a 65-ton capacity. It includes dimensions, engine details, hydraulic system components, load hoisting system capabilities, and descriptions of the carrier, suspension, and axles. Capacities for the crane are listed in a separate section.
The document provides specifications for a Link-Belt RTC-8065 telescopic boom rough terrain crane with a 65-ton capacity. It includes dimensions, engine details, hydraulic system components, load hoisting system capabilities, and descriptions of the carrier, suspension, and axles. Capacities for the crane are listed in a separate section.
CAUTION: This material is supplied for reference use
only. Operator must refer to in--- cab Crane Rating Manual and Operators Manual to determine allowable crane lifting capacities and assembly and operating procedures.
Link-Belt Cranes
RTC--- 8065
5448--- 0205--- D7
RTC--- 8065
Link-Belt Cranes
5448--- 0205--- D7
Table Of Contents Pages 1-- 4 1-- 20
Specifications Capacities
Link-Belt Cranes
RTC--- 8065
5448--- 0205--- D7
This page intentionally left blank
RTC--- 8065
Link-Belt Cranes
Specifications
Telescopic Boom Rough Terrain Crane
RTC8065
65ton (58.97 metric tons)
38 0 (11.58 m)
CL of Rotation
7 0 (2.13 m)
Link-Belt
7.25 (0.18 m) RTC8065
9 5.5 (2.88 m)
A B
3 9 (1.14 m)
4 10 (1.47 m)
3 3 (0.99 m)
23.8
20.2 6 9.5 (2.07 m)
10.9
5 9.5 (1.77 m)
11 9 (3.58 m)
11 6 (3.51 m) 27 3.5 (8.32 m)
45 9 (13.94 m)
General Dimensions
feet
Tailswing of Counterweight
13 9.25
4.20
Turning radius (4wheel steer
23 10
7.26
46 10
14.28
27 5
8.36
49 10
15.19
10 10.5 (3.31 m)
meters
centerline of tires) Turning radius (2wheel steer centerline of tires) Turning radius (4wheel steer outside front carrier corner) Turning radius (2wheel steer outside front carrier corner)
F 8 2.5 (2.50 m) Centerline of tires Full Retraction 10 0.75 (3.07 m) Intermediate Extension 16 4.75 (5.00 m) Full Extension 23 0 (7.01 m)
Tire Size
G Dimension A B C D E F G
29.5 x 25 12 10.75 (3.93 m) 7 11.5 (2.42 m) 2 8 (0.81 m) 12 5 (3.78 m) 8.25 (0.21 m) 25.25 (0.64 m) 11.25 (0.29 m)
29.5 R 25 12 11.75 (3.97 m) 8 0.5 (2.44 m) 2 9 (0.84 m) 12 6 (3.81 m) 7 (0.18 m) 25.25 (0.64 m) 12.25 (0.31 m)
Upper Structure Boom
Cab and Controls
Patented Design
Environmental ULTRA CAB
Boom side plates have diamond shaped
impressions for superior strength to weight ratio and 100,000 psi (689.5 mPa) steel angle chords for lateral stiffness. Boom telescope sections are supported by top, bottom, and adjustable side wear shoes to prevent metal to metal contact.
Standard Boom 38 115 (11.58 35.05 m) four section full power boom Basic mode (or mode B) is the full power, synchronized mode of telescoping all sections proportionally 115 (35.05 m). The exclusive Amax mode (or mode A) extends only the inner midsection to 63 6 (19.35 m) offering increased capacities for inclose, maximum capacity picks. Mechanical Boom Angle Indicator
Boom Head
Five 16.5 (0.42 m) root diameter nylon
sheaves handle up to ten parts of wire rope. Quick reeve design. Boom head designed for quick reeve of hook block. Rope dead end lugs provided on each side of boom head. Easily removable wire rope guards. Fly pinning alignment tool.
Boom Elevation Hydraulic cylinder with holding valve and bushing in each end. Hand control for controlling boom elevation from 3 to +78.
Optional Auxiliary Lifting Sheave
Single 16.5 (0.42 m) root diameter nylon sheave with removable wire rope guard mounted on boom. Use with one or two parts of line. Does not affect erection of fly or use of main head sheaves for multiple reeving.
36.5 (11.13 m) one piece lattice fly, stowable, offsettable to 1, 15, or 30 36.5 61 (11.13 18.59 m) two piece (bifold) lattice fly, stowable, offsettable to 1, 15, or 30
RTC8065
LFC2000 construction process featuring
laminated fibrous composite material. Isolated from sound and vibration by a neoprene seal. Sixway adjustable operators seat with retractable seat belt. Fourway adjustable tilting and locking steering wheel. All windows are tinted and tempered safety glass. Slide by door opens to 3 (0.91 m) width. Sliding rear and right side windows and swing up roof windows for maximum visibility and ventilation. Engine dependent warmwater heater with defroster. Handheld outrigger controls. Sight level bubble Hand throttle Audible swing alarm Warning horn Backup alarm Travel lights Cab mounted work lights Sun visor Electric windshield wiper Mirrors Top hatch window wiper Cup holder Fire extinguisher Circulating fan Dome light
Optional
Amber strobe light and rotating beacon
Emergency steering system Rear steer indicator Air conditioning
Cab Instrumentation Corner post mounted gauges for: Hydraulic oil temperature Fuel Convertor temperature Voltmeter Water temperature Oil pressure Tachometer Audio/visual warning system
Rated Capacity Limiter
Microguard 434 Graphic audiovisual warning system built into dash with anti two block and function limiters.
Operating data available includes:
Crane configuration Boom length Boom angle Head height Radius of load Allowed load Actual load % of allowed load Presettable alarms include: Maximum and minimum boom angles Max tip height and boom length Swing left/right positions Operator defined area alarm is standard. Antitwo block weight designed for quick reeve of hookblock. -2-
Optional Internal RCL light bar: Visually informs operator when crane is approaching maximum load capacity with a series of lights; green, yellow, and red. External RCL light bar: Visually informs ground crew when crane is approaching maximum load capacity kickouts and presettable alarms with a series of lights; green, yellow, and red.
Swing
Bidirectional hydraulic swing motor
mounted to a planetary reducer for 360 continuous smooth swing at 2 r.p.m. Swing park brake 360 electric over hydraulic (spring applied, hydraulic released) multidisc brake mounted on the speed reducer. Operated by toggle switch in overhead control console. Swing brake 360, foot operated, hydraulic applied disc brake mounted on the speed reducer. Travel swing lock Standard; two position travel lock (pin device) operated from the operators cab. Counterweight Pinned to upper structure frame. 12,000 lb (5 443 kg). Optional hydraulically controlled counterweight removal.
Optional 360 (pawlingear) swing lock (meets New York City requirements).
Hydraulic System Main Pump Foursection geartype pump Combined pump capacity 132 gpm (500 Lpm) Mounted on torque converter, powered by engine through a pump disconnect Pump disconnect is a spline type clutch engaged/disengaged from carrier. Pump operates at 3,500 psi (24.1 mPa) maximum system pressure. ORing Face Seal (ORFS) technology throughout with hydraulic oil cooler.
Pilot Pressure / Brake / Counterweight
Removal
Pressure compensated piston pump powered by carrier engine. Operates at 2,650
psi (18.3 mPa) maximum.
Telescope/Outrigger/Steering Pump
Single geartype pump, 24 gpm (91 Lpm)
maximum. Mounted on torque converter, powered by engine through a direct mechanical drive. Pump operates at 3,000 psi (20.7 mPa) maximum system pressure.
Reservoir
170 gal (643.5 L) capacity. Diffuser for
deaeration.
Filtration
One, 10micron filter located inside
hydraulic reservoir. Accessible for easy replacement.
Control Valves: Six separate pilot operated control valves allow simultaneous operation of all crane functions.
Load Hoist System
Standard
2M rear winch with grooved lagging
Twospeed motor and automatic brake Power up/down mode of operation Controls for future addition of auxiliary winch.
Bidirectional pistontype hydraulic motor,
driven through a planetary reduction unit for positive operator control under all load conditions. Asynchronous parallel double crossover grooved drums minimize rope harmonic motion. Winch circuit control provides balanced oil flow to both winches for smooth, simultaneous operation.
Line Pulls and Speeds
Maximum line pull 16,506 lb (7 487 kg) and maximum line speed of 454 f.p.m. (138.4 m/min) on standard 16 (0.41 m) root diameter grooved drum. Rotation resistant rope
Optional
2M front winch with twospeed motor and
automatic brake, power up/down mode of operation. Hoist drum cable followers Third wrap indicators
Carrier Type
Axles
Frame
Suspension
10 10.5 (3.31 m) wide, 151 (3.84 m)
wheelbase. 4 x 4 x 4 (4wheel steer, 4wheel drive) For rough terrain with limited turning area.
100,000 psi (689.5 mPa) steel, double
walled construction. Integral 100,000 psi (689.5 mPa) steel outrigger boxes.
Standard Carrier Equipment
Two front, rear, and midpoint carrier
steps. Nonslip safety strips on carrier deck Deep front storage Fenders Pontoon storage Full lighting package Front towing shackles
Optional Front and rear mounted pintle hook Front tow winch
Engine Engine
Caterpillar 3126B 7.2L
Cylinders cycle Bore Stroke Displacement Maximum brake hp Peak torque (ft. lb.) Electric system Starting system Fuel capacity Alternator Crankcase capacity (total system)
64 4.33 in. (110 mm) 5.00 in. (127 mm) 442 cu. in. (7.2 L) 225 @ 2,200 rpm 646 @ 1,500 rpm 12 volt 12 volt 95 gal (359.6 L) 130 amps 30 qt (28.4 L)
Water/fuel separator on engine
Optional ether injection package
Front and Rear Heavy duty planetary
drive/steer type Front axle disconnect
Front Axle
Rigid mounted to frame
Rear Axle Pin mounted on bronze bushings. Automatic hydraulic rear axle oscillation lock out cylinders engage when upper structure rotates 2.5 past centerline.
Steering
Hydraulic twowheel, fourwheel, and
crab steering. Modes selected by toggle switch on dash. All modes fully controlled by steering wheel.
Optional Rear steer indicator
Tires Front and Rear Standard 29.5 x 25 (28PR) Earthmover type
Optional
29.5R25 XHA 1 star radials
Spare tires and rims.
Brakes Service
Hydraulic disctype brakes at each wheel
end.
Parking/Emergency
Disctype, spring applied, hydraulic released, fade resistant, operated from cab, mounted on front axles.
Transmission
Spicer offhighway threespeed, two
range power shift transmission. Six speeds forward and reverse. Front axle disconnect for two or fourwheel drive.
Outriggers
Three position operation capability.
Four hydraulic, telescoping beam and jack outriggers. Vertical jack cylinders equipped with integral holding valve. Beams extend to 23 0 (7.01 m) centerlinetocenterline and retract to within 10 10.5 (3.31 m) overall width. Equipped with stowable, lightweight 23.5 x 27.25 (59.7 x 69.2 cm) hexagonal steel pontoons. Controls and sight level bubble located in cab.
Confined Area Lifting Capacities
(CALC) System
Three operational outrigger configurations
are available: Full extension 23 0 (7.01 m) Intermediate position 16 4.75 (5.00 m) Full retraction 10 0.75 (3.07 m) For confined area operation, rated lifting capacities are provided for the intermediate and fully retracted outrigger positions. When the outrigger position levers (located on the outrigger beams) are engaged, the operator can set the crane in the intermediate or full retraction outrigger position without having to leave the cab.
Optional Outrigger cover package
Travel Speeds and
Gradeablity Tires Maximum Speed Gradeablity at 70% convertor efficiency Maximum Tractive Effort at 70% convertor efficiency Gradeablity at 1.0 mph (1.6 km/hr) Maximum Tractive Effort at 1.0 mph (1.6 km/hr)
29.5 x 25 19.5 mph (31.4 km/h) 112.9% 76,715 lb (34 797 kg) 55.6% 50,516 lb (22 914 kg)
Crane operating angle must not exceed 35 (77% grade).
Numbers reflect main hydraulic pump engaged.
RTC8065
Axle Loads
Base crane with standard 38 115
(11.58 35.05 m) foursection boom, 2M main winch with 2speed hoisting and power up/down, 630 (192 m) 3/4 (19 mm) wire rope. 4x4x4 carrier with Caterpillar 3126B 7.2L engine, 29.5 x 25 tires, counterweight, and no fuel. Remove 29.5 x 25 tires and wheels 29.5R25 XHA Tires Remove outrigger beams
Upper facing front
G.V.W.
Front axle
Upper facing rear
Rear axle
Front axle
Rear axle
lb
kg
lb
kg
lb
kg
lb
kg
lb
kg
91,488
41 498
44,296
20 092
47,192
21 406
41,804
18 962
49,684
22 253
6,732
3 054
3,366
1 527
3,366
1 527
3,366
1 527
3,366
1 527
964
438
482
219
482
219
482
219
482
219
5,235
2 374
2,461
1 116
2,774
1 258
2,461
1 116
2,774
1 258
Tow winch
686
311
1,002
454
316
143
1,002
454
316
143
100 gal (378.5 L) fuel
685
310
364
165
321
145
364
165
321
145
2M auxiliary winch with 630 (192 m) of
3/4 (19 mm) rope
779
354
203
92
982
445
920
417
141
64
3628
1 646
4,858
2 204
1,230
558
4,858
2 204
1230
558
353
160
163
74
190
86
518
235
165
75
12,000
5 443
6,586
2 987
18,586
8 430
17,633
7 998
5,633
2 555
Remove front carrier counterweights
Hydraulic counterweight removal Remove counterweight Air conditioning
287
130
55
25
232
105
209
95
78
35
36.5 (11.13 m) onepiece lattice fly, with
tip lugs, stowable
1,542
700
2,485
1 115
619
415
1,039
471
2,581
1 171
36.5 61 (11.13 18.59 m) twopiece
(bifold) lattice fly, stowable
2,250
1 021
3,165
1 436
915
415
1,094
496
3,344
1 517
Fly storage brackets with all fly options
160
73
228
103
69
30
81
36
241
109
Auxiliary lifting sheave assembly
110
50
355
152
225
102
233
106
343
156
8.5ton (7.71 mt) hook ball @ front bumper
360
163
566
256
206
93
n/a
n/a
n/a
n/a
70ton (63.50 mt) 5sheave hook block
@ front bumper
1,390
631
2,186
992
796
361
n/a
n/a
n/a
n/a
60ton (54.43 mt) 4sheave hook block
@ front bumper
1,150
522
1,809
821
659
299
n/a
n/a
n/a
n/a
Adjust gross weight and axle loading according to component weight. Note: All weights are 3%.
Tire
Max. Axle Load @ 20 mph (32.2 km/hr)
29.5 x 25 (28PR)
53,000 (24 041 kg)
29.5R25 XHA 1 Star
53,000 (24 041 kg)
LinkBelt Construction Equipment Company
Lexington, Kentucky
www.linkbelt.com
LinkBelt is a registered trademark. Copyright 2005. All rights reserved. We are constantly improving our products and therefore reserve the right to change designs and specifications.
RTC8065
-4-
5448--- 0205--- D7
This page intentionally left blank
RTC--- 8065
Link-Belt Cranes
5448--- 0205--- D7
This page intentionally left blank
RTC--- 8065
Link-Belt Cranes
5448--- 0205--- D7
This page intentionally left blank
RTC--- 8065
Link-Belt Cranes
5448---0205---D7
Link--Belt Construction Equipment Company
Lexington, Kentucky
www.linkbelt.com
RLink--Belt is a registered trademark. Copyright 2005. We are constantly improving our products and therefore reserve the right to change designs and specifications.
