Light Chaser

CMYK
CIRCUIT
Visit www.deekshith.in for more unique project ideas and circuits
IDEAS
MUSICAL LIGHT CHASER
DEBARAJ KEOT
his music-operated lighting effect generator comprises five

sets of 60W bulbs that are ar-
ranged in zig-zag fashion. The bulb

sets glow one after another depending
on the intensity of the audio signal.
No electrical connection is to be made
between the music system and the
IVEDI
S.C. DW
lighting effect generator circuit. You

just need to place the gadget near the
speakers of the music system.
Fig. 1 shows the complete circuit
of the musical light chaser, while Fig.
Fig. 1: Circuit diagram of musical light chaser
82 JANUARY 2005 ELECTRONICS FOR YOU

WWW.EFYMAG.COM
http://www.deekshith.in/search/label/Projects
:Visit for more unique project
ideas and circuits
CMYK
CIRCUIT
IDEAS
2 shows pin configurations of 9V regulator 7809, triac BT136 and level meter
IC LB1403.
The circuit is powered by regulated
9V DC. The AC mains is stepped down
by transformer X1 to deliver a secondary output of 12V AC at 250 mA. The
transformer output is rectified by a
full-wave rectifier comprising diodes
D1 and D2 and filtered by capacitors
C1 and C2. Regulator IC 7809 (IC1)
provides regulated 9V power supply
to the circuit. Closing switch S1 provides power to the circuit and LED1
glows to indicate that the circuit is
ready to work.
When you put your music system
in front of the condenser microphone
of the light chaser, the sound pressure
variation is converted into electrical
signals by the condenser microphone.
These weak electrical signals are amplified by op-amp A741 (IC2), which
is configured as an inverting amplifier. Using preset VR1 you can set the
sensitivity of the circuit.
The amplified output is fed to IC
LB1403 (IC3) at its input pin 8. IC3 is a
five-dot LED level meter commonly
used in stereo systems for LED
bargraph displays. It has a built-in am-
Fig. 2: Pin configuration
plifier, comparators and constant current source at its output pins.

Depending on the intensity of the
input audio signals, all or some outputs of IC3 go low to drive transistors
T1 through T5, which, in turn, fire the
corresponding triacs TR1 through TR5
via their gates and multicoloured zigzag bulb sets comprising ZL1 through
ZL5 glow.
When the audio level is low, only
triac T1 is fired and the zig-zag bulb
set ZL1 turns on and off sequentially.
When the audio level is high, triacs
TR1 through TR5 get fired and all the
bulb sets (ZL1 through ZL5) turn on
and off sequentially.
Pin 7 of IC3 is used for selecting
the response speed of the lighting.
The larger the time constant, the
slower the response, and vice versa.
The time constant can be changed by

changing the values of resistor R6,
variable resistor VR2 and capacitor
C7. Here, variable resistor VR2 is used
for varying the response speed of the
chaser light as desired. When VR2 is
set in the minimum resistance position, the response is very fast, and
when it is set at the maximum resistance, the response is slow.
The complete circuit including the
power supply can be constructed on
any general-purpose PCB or
a small Vero board. Triacs TR1
through TR5 should be kept away
from the op-amp and its related components. The metallic parts of the
triacs should not touch each other and
the other parts of the circuit. After
assembling the circuit, house it in a
suitable shockproof plastic cabinet.
Make some holes in the cabinet for
heat dissipation.
Note. 1. Some zig-zag lights have
a special bulb called master bulb for
automatic flickering. It should be
removed and replaced with a simple
non-flickering colour bulb.
2. Never touch any naked part of
the circuit when it is connected to the
mains. z
WWW.EFYMAG.COM
ECTRONICS FOR YOU JANUARY 2005 83
http://www.deekshith.in/search/label/Projects
:Visit for moreE Lunique
project ideas and circuits
Get this
project done!
Get the Document + PPT + KIT
Are you interested in doing this project either as
your college (mini / major) project or as your
hobby? We can help you out. We can provide you
with all the documents including documentation,
PPT, etc that you need as a student to present
this project at your college.
Also, if you are in need of the hardware kit for
this project, we can provide it to you at a cheaper
cost and in little time.
Contact: http://deekshith.in/p/contact.html
Email: [email protected]
Facebook: http://facebook.com/deekshithallamaneni
Phone: +919441921293 (Local to Hyderabad, India)
http://www.deekshith.in/search/label/Projects :Visit for more unique project ideas and circuits

Light Chaser

Uploaded by

Copyright:

Available Formats

Light Chaser

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Light Chaser

Uploaded by

Copyright:

Available Formats

CMYK

MUSICAL LIGHT CHASER

his music-operated lighting effect generator comprises five

ranged in zig-zag fashion. The bulb

lighting effect generator circuit. You

Fig. 1: Circuit diagram of musical light chaser

82 JANUARY 2005 ELECTRONICS FOR YOU

Fig. 2: Pin configuration

plifier, comparators and constant current source at its output pins.

The time constant can be changed by

Visit www.deekshith.in for more unique project ideas and circuits

http://www.deekshith.in/search/label/Projects :Visit for more unique project ideas and circuits

You might also like