Hyosung Error Codes

Hyosung Error Codes
Error Code
0
20001
20002
20003
20004
20005
20010
Description
Resolution
Normal Status
Normal Status
Unable to detect a cassette
Remove and replace cassette - Check the micro-switch

located on the inside left wall of the dispenser. Adjust the
micro-switch if needed, also check the white plastic clips
that hold the cassette in place. If they are broken the
cassette will not stay in the dispenser.
Low Cash
Low cash warning sensor on dispenser is open. When "Low

Cash Warning" is enabled in the Transaction Setup menu,
this sensor will open when the cassette reaches (+/-) 75
bills. If this machine is typically stocked with a low amount of
bills, we recommend disabling this function.
Reject Bin is Full
Empty reject bin - if bin is empty, do a Cassette Total (from

the settlement menu) - If that doesn't help then check that
AP, BIOS and CDU ROM versions are compatible.
Vault Door is Open
This error occurs when the circuit between the mainboard

and the door switch is open. Check vault door switch. This
white plunger switch is located in the upper left corner of the
vault, or on along the front edge of the cash dispenser tray.
Also check that black and white, 2 wire connector is properly
connected at rear of main board. Move the vault switch
forward to aid door clearance problems. Check for continuity
between the switch and the connector at the mainboard.
CDU Type Mismatch
CDU ROM does not match AP software. The dispenser and

mainboard are programmed with a country code (USA or
Canada). The two codes must match. If they do not the
20005 error will occur in which case the CDU will need to be
reprogrammed to match the AP on the mainboard. Also, if
the wrong parameters are entered when the CDU is
programmed, this error can occur.
Receipt Paper Jam
Remove jammed paper - Release receipt paper drawer by

pressing the tab with the green sticker located at the front of
the printer. In most cases you may have to remove the
printer to locate difficult jams. NOTE: Do NOT use metal
objects to clear jams, use a business card or stiff paper.
Make sure you only are using 21# paper. Paper of a lesser
thickness is more prone to jamming.
20012
20013
20014
20215
21315
21A15
21B15
24A15
24B15
Receipt printer feed lever open
Close the feed tray on the printer. If the paper tray is already
closed, try opening and closing the tray, try the printer reset
switch. Otherwise the printer may require service.
Receipt paper is empty
Replenish the paper roll, if there is already paper in the

printer look for jams or obstructions. Try the printer reset
switch. If it still has the error the printer may require service.
Thermal printer is overheated
If this error occurs during the printing of a long journal, then

allow the printer to cool and try again. You may also want to
try the reset button on the printer to clear this error. If this
error persists, the printer will require service.
CDU detects bills prior to

dispensing
This means that while the ATM was initializing it detected a

blocked sensor in the cash dispenser (CS2 sensor).
Remove any jammed bills from the dispenser, if no bills are
present try using compressed air to clean the dispenser (a
sensor may be blocked by dust). Check and reseat all belts.
Loose belts can slip off rollers and block sensors.

dispensing

blocked sensor in the cash dispenser (CS13 sensor).

dispensing

blocked sensor in the cash dispenser (CS1A sensor).

dispensing

blocked sensor in the cash dispenser (CS1B sensor).

dispensing

blocked sensor in the cash dispenser (CS4A sensor).

dispensing

blocked sensor in the cash dispenser (CS4B sensor).
Error during card swipe
This error occurs when customer attempts to swipe their

card and are unsuccessful. It may indicate that the card
reader needs to be cleaned, repositioned or simply that the
customer didn't swipe their card properly. If persistent, clean
and test the card reader in diagnostics. NOTE: it is very
common to see this error in the error summary and does not
usually indicate a bad or defective part.
Receipt paper cutter error
Remove any jammed paper. You may need to remove the

printer to clear jams. NOTE: Do not use metal objects to
clear the jam. Use a business card or stiff paper to clear
jams. Otherwise try the reset button or have the printer
serviced.
Receipt Paper Jam

the printer. You may need to remove the printer from the
ATM to access the jam. NOTE: Do not use metal objects to
clear jams, use a business card or stiff paper to poke
around.
Receipt paper cutter error
Remove any jammed paper. You may need to remove the

printer to clear jams. NOTE: Do not use metal objects to
clear the jam. Use a business card or stiff paper to clear
jams. Otherwise try the reset button or have the printer
serviced.
Printer connection error
Check cables between Printer and Mainboard, remove

cables (even though they may be attached) and re-connect.
Use an electrical parts contact cleaner to clean the
terminals. Try the reset button on the printer. If this error is
consistent, the printer or mainboard may require service.


Thermal printer is overheated during operation
If this error occurs during the printing of a long journal, then

allow the printer to cool and try again. You may also want to
try the reset button on the printer to clear this error. If this
error persists, the printer will require service.
Axxx3
Receipt Paper Jam

the printer. You may need to remove the printer from the
ATM to access the jam. NOTE: Do NOT use metal objects
to clear jams, use a business card or stiff paper to poke
around.
Axxx4
Receipt paper is empty
Replenish the paper roll. If roll is ok, then try the reset button
on the printer. Otherwise the printer needs service.
90001
A0008
A0803
A0808
ADN04
ADN0F
ADNxx
Axxx2
Axxx5
Receipt paper is jamming during

loading
Remove any jammed paper and then reload. You may need
to remove the printer to clear jams. NOTE: Do not use metal
objects to clear the jam. Use a business card or stiff paper
to clear jams. Otherwise try the reset button or have the
printer serviced.
C0011
CDU sensor is tripped
C0014
This indicates that during a dispense, the sensor located at

the front of the CDU shows a blockage (CS13 or CS2). The
primary reason for this is a bill which bounces back from the
cash tray (sometimes from a customers fingers). Check the
front of the CDU and the cash tray for blockage. Reinitialize
the ATM to put back in service. In the case of a dispute from
the error, use CDU data in the journal to verify how many
notes were actually dispensed.
Similar to the COO11 error, this would indicate a bill jam
close to the exit of the CDU or near the reject bin. Check for
jammed notes or blocked sensors.
Most typically a COO11 error, this would indicate a bill jam

at the exit sensor of the Cash Dispenser. Usually caused by
a customer putting fingers in the cash drawer during
dispense. Other than upgrading the cash tray or using a
sign to warn customers, you can loosen the screws that hold
the dispenser and slide it back.
Check dispenser for jammed bills and restart the machine. If

no bills are present try using compressed air to clean the
dispenser (a sensor may be blocked by dust). Otherwise the
dispenser may require service
Check dispenser for jammed bills and restart the machine. If

dispenser may require service
CDU motor failure
Motor speed (measured at the encoder wheel) was not

within spec. Verify that CS8 or encoder wheel sensor is in
place and wire connection is good. Can indicate a bad
motor or encoder sensor.
C001x
C0028
C002x
C0030
C0031
CDU Gate solenoid error
C0032
Outlet solenoid error
The CDU did not respond to its solenoid function check.

Check the wiring connections to the solenoid(s). Check
wiring connections to the CDU main board.
Check and verify all connections to the dispenser circuit
board. Check wiring to the solenoid(s).
C0035
Usually caused by loss of battery power to the CDU

mainboard. The only way to recover from this error is to
reprogram the CDU data. This may require special software
CDU Encoder error
and cannot be done over the phone line.
Double detect module reporting error, check wiring to the
Double Note detect module failure module.
Double Note detect module failure Double detect module reporting error, check wiring to the
(2)
module.
C0036
One or more sensors in the dispenser detected a blockage

prior to initializing. Check for notes in the Cash Dispenser. If
dispenser may require service.
C0033
C0034
Detected notes in path before

initializing
C0037
Sensor(NS7) for detecting Double

is covered during dispensing note
Check the sensor that is activated when you close the reject
bin door (2k/4k dispensers only). If the sensor is not being
pressed then the error will occur. Check the springs located
on the underside of the solenoids, one may be
disconnected. Otherwise the CDU will require repair /
replacement.
C0039
Gate sensor open during

initializing
C003B
Check for notes in the Cash Dispenser. If no bills are

sensor may be blocked by dust). Otherwise the dispenser
Notes detected during installation may require service.
C0040
Cassette removed during

dispense
Reset the cassette, check position of microswitch on right

rear wall of cassette bay in the dispenser. Check the
condition of the white plastic cassette retaining clips in the
dispenser.
C0041
Check the condition of the cash in the cassette. Verify that

the cash is of good quality. The CDU belts or the Cassette
rollers may need to be cleaned (rubbing alcohol). Check that
Tried to dispense notes more than the denomination in Transaction setup matches the actual
5 times
denomination loaded.
Note jam

may require service
More than 10 notes rejected

during one transaction
Verify the quality of the cash. Straighten and shuffle cash in

the cassette. Check the reject analysis to determine the
cause of reject (reports menu). If the cash is of known good
quality then try cleaning the cassette and dispenser.
Otherwise service to cassette or dispenser may be required.
C0044
More than 5 notes rejected

consecutively

the cassette. Check the reject analysis to determine the
cause of reject (reports menu). If the cash is of known good
quality then try cleaning the cassette and dispenser.
Otherwise service to cassette or dispenser may be required.
C0045
Notes Overdispensed
C0046
CDU Hardware Failure
Check NS4 Sensor

Error reported during CDU initialization. Check cabling and
potential blockages and power cycle ATM. (CDU Board
dropped Firmware)
C0047
Feed error
This error occurs when the dispenser attempts to pull a bill

from the cassette and is unsucessfull before the dispenser
times out. Depending on the model of dispenser there are
different causes and possible solutions. It can be as simple
as the cassette being empty, rollers need cleaning to a
firmware upgrade to the CDU.
C0048
Incorrect bill count
Verify cash count in the Settlement menu.
Jammed notes

may require service
C0042
C0043
C004A
C004B
Long note detected 3 times

consecutively
C004C
Miscount of notes between

sensors

the cassette. Try cleaning the cassette and dispenser. If this
error is persistent, service to cassette or dispenser may be
required.
Verify operation of exit gate. Check the number of
dispensed notes. Clean the dispenser and test using
diagnostics. Dispenser may require service.
Cash cassette not properly set
Reset the cassette, check position of microswitch on right

rear wall of cassette bay in the dispenser. Check the
condition of the white plastic cassette retaining clips in the
dispenser. MB1000 check condition of the clutch alignment
screw.

sensors
Test CDU using diagnostics, use journal to verify amount of

dispensed notes versus requested notes. Clean dispenser
and cassette. If error is persistent the dispenser may require
service.
C004D
C004E
C004F

sensors
C0050
Power failure during dispense
Test CDU using diagnostics, use journal to verify amount of

dispensed notes versus requested notes. Clean dispenser
and cassette. If error is persistent the dispenser may require
service.
Remove any notes from path. Before reinitializing the ATM,
first the verify amount of dispensed notes in the cassette
against the journal.
C0053
Possibly due to too many rejects, may require repair or

cleaning if consistent. Check the Reject Analysis, this may
help determine the cause. Cash quality, condition of the
Over 150 notes requested
rollers in the cassette can effect this condition.
Remove any notes from path, verify amount of dispensed
Detected notes in path after
notes. Clean dispenser. Verify the amount of bills against
dispense
the journal.
Double detect module may require adjustment. Check wiring
CDU double detect module failure. and CDU mainboard connections.
C0055
Detected long notes at outlet

sensor
C0051
C0052
C0056
(See definition of C0011 error) this is typically a bounce

back of a bill during dispense causing the exit sensor to
remain blocked for a longer time than is expected.
C0057
Exit gate sensor failure

Cassette information is not
properly set
Check condition of exit gate, and the exit gate sensor.
C0059
Cash cassette 2 removed prior to Set the cash cassette. Inspect the cassette detection
dispense.
microswitch. Reposition the microswitch if necessary.
C005A
Cash cassette 1 removed prior to Set the cash cassette. Inspect the cassette detection
dispense
microswitch. Reposition the microswitch if necessary.
C005B
Cash cassette 2 misfeed
C005D
C005E
Double detect constantly

Dispense command size check
error
C005F
Dispense command error
CDU programming is not accurate or complete.
Check cassette for jams, check condition of bills in cassette.

Inspect double detect module and adjust as necessary.
Check and clean the cassette and rollers, verify the quality
of cash.
Re-initialize machine, verify connections to mainboard.
Check for unplugged sensors.
Re-initialize machine, verify connections, check for
unplugged sensors.
C006x
Sensor failure

may require service
may require service
Check all wiring connections to CDU mainboard. Reinitialize
CDU
CDU
CDU.
C007x
Sensor failure
C0082
Shutter failure
C0083
Stacker sensor failure
C0084
Shutter close error
C009F
3Cassette misfeed error
C00AB
Notes detected before initalizing
Check if notes available in cassette

Clear notes from dispenser. Possibly dust or foreign object
blocking sensor.
CS12 Sensor blocked
MB2100T - The CS12 sensor, which is located at the upper

part of the cash tray was blocked while the machine was
either dispensing or initializing. Clear the cash tray of any
bills or foreign objects. If the error persists, the vault
assembly may need to be removed to inspect / access the
cash tray sensors.
CS14 Sensor blocked
MB2100T - The CS14 sensor, which is located close to front

of the cash tray, was blocked while the machine was either
dispensing or initializing. Clear the cash tray of any bills or
foreign objects. If the error persists, the vault assembly may
need to be removed to inspect / access the cash tray
sensors.
CS12 & CS14 Sensors blocked
MB2100T - Both the CS12 and CS14 sensors were blocked

while the machine was either dispensing or initializing.
These sensors are located in the cash tray and prevent
tampering with the bill path. Clear the cash tray of any bills
or foreign objects. If the error persists, the vault assembly
may need to be removed to inspect / access the cash tray
sensors.
Sensor block while dispensing
MB2100T - A blockage was detected between the CS13

(CDU exit gate) and CS12 cash tray sensors. There may be
a note stuck in the upper part of the cash tray ramp. Try
clearing the cash tray of notes or foreign objects. Open the
vault and slide the dispenser back to access the exit gate
area. Both sensors must be blocked for this error to occur.
C00C7
C00C8
C00C9
C00D0
C00E1
NS4 dark
MB2100T - A blockage was detected between the CS12

(upper cash tray sensor) and CS14 (lower cash tray sensor).
There may be a note stuck in the cash tray ramp. Try
clearing the cash tray of notes or foreign objects. Open the
vault and slide the dispenser back to access the exit gate
area. Both sensors must be blocked for this error to occur.
Nanocash only - verify connections to sensors. Check wiring
to mainboard.
Verify connections to NS4 sensor. Check all wiring to
mainboard.
C00FF
Sensor blocked
N/A
C00D1
Sensor blocked while dispensing
C00E0
NS2A, NS2B dark
CANCE
CDN01
CDN05
CDN0F
CDN11
CDN12
CDN13
CDNxx
D0001
D0002
D0005
D0011
User canceled transaction at

surcharge
No Response after send
command
CDU connection failure

No Response after 3 retry of
command
No Response between ENQ-ACK
after 5 retry of ENQ
No Response after 5 retry
because of timeout between STXBCC interval
This is not an error, but rather a statistic to notify how many

users respond "no" to the surcharge notification.
Check cables between CDU and Mainboard, remove cables

(even though they may be attached) and re-connect. Use an
electrical parts contact cleaner on terminals. This error is of
concern only if it is repeated. Outside interference may
cause it (neon signs, lights).

Modem initialization error
Check modem in diagnostics or modem test. If persistent, it

could be a defective modem. Note: If the modem is
defective, this error will most likely occur frequently. One or
two instances of this error does not usually indicate a
defective part. [Check Modem Initial String]
Reversal transaction failed.
The ATM attempted to do a reversal and could not. Check

transaction with the processor. Verify CDU functionality with
diagnostics. Verify phone connection. Look in error
summary for D1800, D2000.
Undefined network processing

error
Code reported by host processor. Specific meaning or

definition can vary between the different processors.
Contact your ISO or processor if you encounter an
excessive amount of these errors, or you cannot complete a
test transaction because of this error.
Format error in the message.

D0012
D0013
D0014
D0019
D0020
D0024
D0031
D0039
D0041
Invalid Transaction

Invalid Amount

Invalid Card Number

Reenter the entire transaction
Code reported by host processor (Shazam). Specific

meaning or definition can vary between the different
processors. Contact your ISO or processor if you encounter
an excessive amount of these errors, or you cannot
complete a test transaction because of this error.
Surcharge screen should have

been displayed

Exceeds issuer withdrawal limit

Issuer financial institution is not

supported by a processor

No credit account

No credit account found for the

CCN

D0043
D0050
D0051
D0052
D0053
D0054
D0055
D0056
D0057
Stolen Card

Transaction is not approved

Insufficient funds

No checking account

No savings account

Expired Card

Invalid PIN
Code reported from host processor - Verify all programming.

In the case of a new installation, if master keys are not
bound properly, Terminal ID is not active or if programming
is not correct for the host this can occur. If all programming
appears correct, contact the processor and have them trace
the Terminal ID.
No card record found

Transaction not permitted - card

D0058
D0059
D0060
D0061
D0065
D0067
D0075
D0078
D0080
Transaction not permitted Terminal

Customer should contact his or

her financial institution

Allowable withdrawal limit is

exceeded

Exceeded withdrawal limit

Exceeds withdrawal frequency

limit

Capture card at the terminal

(requires card be picked up at
ATM only).

Number of PIN tries exceeded

No Account

Invalid Date

D0081

Time out: response not received processors. Contact your ISO or processor if you encounter
in time allowed (SHAZAM switch- an excessive amount of these errors, or you cannot
in-front (SIF) terminals).
D0082
Cashback limit exceeded.

Cannot verify PIN

Processor not available; acquirer

processor unable to send
message

Cannot verify PIN

Cutoff complete for terminal;

cannot process prior days
business

Bank unavailable

D0083
D0084
D0086
D0090
D0091
D0092

test transaction because of this error. [Possible Incorrect
Check Digit (Master Keys)]
D0093
System unavailable
Transaction serial number
mismatch
Verify all programming, contact host processor
D0094
Record format mismatch
D0095
Routing ID mismatch
Verify Routing ID number - contact host processor
D0096
Terminal ID mismatch
Response type mismatch
(reversal)
Verify Terminal ID number - contact host processor
D0097
D0099
Response type mismatch (dayclose)

(Configuration)
D009A

(Withdrawal, Balance, Transfer)
D009B
STX omitted
D009C
ETX omitted
D009D
FS omitted (after response code)

Verify that version of Mini-Bank Software matches host
processor. Contact host processor
D009E
FS omitted (after retrieval

reference number)
Verify all programming. Verify that version of Mini-Bank

Software matches host processor. Contact host processor
D009F
FS omitted (after system trace

audit number)

D00A0
FS omitted (after account

balance)

D00A1
FS omitted (after available

balance)
D00A2
FS omitted (after available

balance)

(Check T-DES Type)
D00A3
FS omitted (after authorization

response text)

D00A4
ETX is in wrong place

D00A5
FS omitted (after total cash

dispense amount in day close)

D00A6
FS omitted (after total non cash

dispense amount in day close)

D00A7
FS omitted (after surcharge

amount in day close message)

D00A8

FS omitted (after surcharge
Software matches host processor. Check that Dual Master
amount in configuration message) Key is disabled (non Coredata). Contact host processor
D00A9
ETX omitted (from configuration

message)

D00B0
Invalid Terminal ID
Contact host processor
D0100
Transaction approved
D0101
Expired card
D0102
Unauthorized usage
D0103
PIN error
D0104
Invalid PIN
D0098

D0105
Bank unavailable
D0106
Card not supported
D0107
Insufficient funds
D0108
Ineligible transaction
D0109
D0110
Ineligible account
Number of daily withdrawals
exceeded
D0111
Cannot process transaction
D0112
Amount too large
D0113
Account closed
D0114
PIN tries exceeded
D0115
Database problem
D0116
Withdrawal limit already reached
D0117
Invalid amount
D0118
External decline
D0119
System error
D0120
Contact card issuer
D0121
Routing lookup problem
D0122
Message edit error
D0123
Transaction not supported
D0124
Insufficient funds
D0125
Western Union sender data error
D0126
Western Union receiver data error
D0127
CRC error
D0128
Pre-pay transaction failed
D0129
Pre-pay transaction rejected
D0130
Invalid mobile phone number
D0131
Pre-pay account limit reached
D0132
D0133
Pre-pay system unavailable

Response would exceed message
size limit
D0134
Necessary information missing to

precess transaction
D0135
Second Invalid PIN(second

"Invalid PIN" try in a row and one
try is left before deactivation)
D0300
Modem is not responding
D1000
No Connection
D1100
ENQ not received from host
D1200
Transmission error
D1300
NAK sent 3 times to host
Use diagnostic or modem test to test modem. If error is

persistent, modem may be defective.
persistent, modem may be defective.
persistent, modem may be defective
Verify host phone number - See D170x. If persistent, it could
be a defective modem.
D1500
D1702
D1704
D1706
D170x
Modem connection time out - host Verify host phone number - verify modem speed - See
not responding
D170x. If consistent, it can be a defective modem
Modem connection error
Phone line connected to ATM will not support data

communication. In line filter may help this. Excessive EMI
emissions from outside source (neon sign, freezer)are likely
causes. This can also be a problem with programming,
check all programming (especially Dual Master Key setting
and Host Processor Mode).


Modem cannot support

connection - excessive line noise
(usually D1704/06)
Phone line connected to ATM will not support Datacommunication. In line filter may fix this. Excessive EMI
emissions from outside source (neon sign, freezer). This
can also be a problem with programming, check all
programming (especially Dual Master Key setting and Host
Processor Mode).
D1800
No dial tone
D1900
No answer
D2000
Phone line Busy
Verify that incoming phone line is plugged into "Line" rather

than "Phone" on mainboard. Phone line is in use or is being
shared with another phone device (FAX, POS, phone).
NOTE: This error occurs only if there is no dial tone at the
mainboard.
Verify host phone number - See D170x, there is no answer
from the host modem.
Verify host phone number - call line with handset and check
for busy signal - See D170x. ATM modem is receiving a
busy signal when it dials out.
D2100
Modem initialization error
Check modem in diagnostics or modem test. If persistent, it

could be a defective modem. Note: If the modem is
defective, this error will most likely occur frequently. One or
two instances of this error does not usually indicate a
defective part.
D2200
EOT not received from host

D2500
Cannot connect to the host
Check the connection
D2510
Timeout while Sending

Communication error while
Sending
D2511
D2513
D2514
Timeout while Receiving

Communication error while
Receiving
D2515
Socket Error while Receiving
Verify the Host phone number is programmed correctly. Do

not use spaces or dashes in the phone number string.
D3204
Invalid Host phone number
E000x
RMS port failure, response time

out, modem failure, no dial tone
F0001
Current Number of Bills is 0
Verify RMS settings (Host Setup) - See D170x

Load notes into the cash cassette - use Add Cassette
function in Settlement
F0002
No Surcharge Owner set
Set Surcharge owner - (Customer Setup)
F0003
No Surcharge Amount
No refresh timer set when
advertisement is enabled
No Advertisement text when
advertisement is enabled
Dispense limit set error (must be
less than 25 notes)
Set Surcharge amount - (Customer Setup)
F0004
F0005
F0006
F0007
Set refresh timer - (Customer Setup)

Set Advertisement text - (Customer Setup)
Set Dispense limit - (Transaction Setup)
Valid Denominations are $10, $20, $50, $100 - (Transaction
Setup)
F0008
Denomination Set error

Fast Cash Set error (cannot
exceed dispense limit)
Check fast cash settings (Transaction Setup)
F0009
Master Key index is invalid
Check Master Key index - verify checksum (Host Setup)
F000A
Master Key is empty
Check Master Key checksum - reinject key (Host Setup)
F000B
Host Telephone Number is not set Set Host Telephone Number - (Host Setup)
F000C
Set RMS Password - (Host Setup)
F000E
Error Retry timer is not set

RMS Password is not set when
RMS is enabled
RMS phone number is not set
when RMS send is enabled
F000F
Terminal ID is not set
Set Terminal ID number - (Host Setup)
F0010
Set Routing ID number - (Host Setup)
F0011
Routing ID is not set

Master Key Serial number is not
set
Set Master Key serial number - (Host Setup)
F0013
NVRAM Failure
Fatal error, defective memory chip. Replace Mainboard
F0014
NVRAM Failure
Fatal error, defective memory chip. Replace Mainboard
F0015
ATM Serial No. Empty

Default Master Password is not
changed
F000D
F0016
F0020
Set Error retry timer (Host Setup)
Set RMS Phone number - (Host Setup)
F0021
Host IP Address is not inputted

RMS IP or Port is not inputted in
RMS Enable
P0001
Deposit Error
Deposit Error
P0002
Deposit Timeout
Deposit Timeout
P0003
Invalid Deposit
Invalid Deposit
P0004
Deposit Cancelled
Deposit Cancelled
PDN01
EPP Cmmunication Error
WebRMS failed to dial into the

ATM
This does not mean that the ATM is down; it's a warning
message that WebRMS could not dial into the ATM after
three attempts during its daily scheduled dial-in period.
Make sure the ATM is turned on, the phone line fits securely
on both ends, and not shared with a voice phone nor
experiences static.
WebRMS low cash warning
This is a courtesy alert warning, along with an email

message, that you requested to receive when the total bill
count is under a certain amount. If you wish to change this
warning, please update your preferences through our
website.
W0003
WebRMS could not retrieve the

local ATM time
Although webRMS successfully retrieved the journal

information, it could not find the ATM's local time. (This is
equivalent to the "-1/-1/-001" error when using Windows
RMS). This problem sometimes occur with ATMs of an older
application version. Make sure you are running the latest
application version.
W0004
The ATM time, as set in the

Operator Function Menu, is
incorrect
WebRMS has detected that the ATM probably has incorrect

date and time settings. You will need to physically go to the
ATM location and manually reset the correct date with the
Master Password.
WebRMS coincidentally detected

that the ATM was in Operator
mode at the time the ATM was
dialed into.
WebRMS has failed to dial into
the ATM consecutively for more
than 3 days.
This is not an error in particular, but a simple warning that

someone was locally on-site at the ATM, and used its
Operator Function menu.
Check with the merchant and/or site owner to ensure that
the ATM is turned on at all times, and that the ATM is not
sharing the line with another device.
W0001
W0002
W0005
W0006

Hyosung Error Codes

Uploaded by

Copyright:

Available Formats

Hyosung Error Codes

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hyosung Error Codes

Uploaded by

Copyright:

Available Formats

Hyosung Error Codes

Unable to detect a cassette

Remove and replace cassette - Check the micro-switch

Low cash warning sensor on dispenser is open. When "Low

Reject Bin is Full

Empty reject bin - if bin is empty, do a Cassette Total (from

Vault Door is Open

This error occurs when the circuit between the mainboard

CDU Type Mismatch

CDU ROM does not match AP software. The dispenser and

Receipt Paper Jam

Remove jammed paper - Release receipt paper drawer by

Receipt printer feed lever open

Receipt paper is empty

Replenish the paper roll, if there is already paper in the

Thermal printer is overheated

If this error occurs during the printing of a long journal, then

CDU detects bills prior to

This means that while the ATM was initializing it detected a

CDU detects bills prior to

This means that while the ATM was initializing it detected a

CDU detects bills prior to

This means that while the ATM was initializing it detected a

CDU detects bills prior to

This means that while the ATM was initializing it detected a

CDU detects bills prior to

This means that while the ATM was initializing it detected a

CDU detects bills prior to

This means that while the ATM was initializing it detected a

Error during card swipe

This error occurs when customer attempts to swipe their

Receipt paper cutter error

Remove any jammed paper. You may need to remove the

Receipt Paper Jam

Remove jammed paper - Release receipt paper drawer by

Receipt paper cutter error

Remove any jammed paper. You may need to remove the

Printer connection error

Check cables between Printer and Mainboard, remove

Printer connection error

Check cables between Printer and Mainboard, remove

Printer connection error

Check cables between Printer and Mainboard, remove

Thermal printer is overheated during operation

If this error occurs during the printing of a long journal, then

Receipt Paper Jam

Remove jammed paper - Release receipt paper drawer by

Receipt paper is empty

Receipt paper is jamming during

CDU sensor is tripped

CDU sensor is tripped

This indicates that during a dispense, the sensor located at

CDU sensor is tripped

Most typically a COO11 error, this would indicate a bill jam

CDU sensor is tripped

Check dispenser for jammed bills and restart the machine. If

CDU sensor is tripped

Check dispenser for jammed bills and restart the machine. If

CDU motor failure