02.susol MCCB E 1306

www.lsis.
biz
Super Solution
Low voltage circuit breakers
LSIS continues
the value and the prominence of LG
New Name for LG Industrial Systems,

New Take-off for LSIS
To advance to the next level,

LG Industrial Systems is reborn as LS Industrial Systems.
LSIS will continue to lead the future
of industrial electrics and automation by providing
Total Solution, a core essential
for competition in the 21st century industrial era.
Research & Development

We provide differentiated values.
The world-class Power Testing & Technology Institute guarantees
certified products and global brands.
The PT&TI is an accredited testing laboratory that provides a worldwide testing service with a
1500MVA-capacity High Power Laboratory, a High Voltage Laboratory, and a Reliability Testing
Laboratory. Its testing has been fully acknowledged and recognized by overseas testing certification
bodies, such as KEMA of Netherlands, UL of America, and CE of the EU for its low voltage testing.
Global technology and R&D are behind the best industrial

Electric power and automation products from LSIS
Quality Test at PT&T
High Voltage Test / Impulse Test
Characteristics Test / VCB Characteristics Test
Electro Technology R&D Center

The Electro Technology R&D Center focuses on
overall research and development activities related
to power supply systems such as low and high
voltage equipment as well as integrated digital
networks, automatic switchboards and integrated
power protection.
The R&D Center maximizes energy efficiencies by
integrating rapidly developing information &
technology, communication, electronics and
mechanical engineering, while concentrating its
efforts in creating a safe and pleasant industrial
environment.
Power Equipments
The R&D Center researches products and technologies related to
low and high voltage circuit breakers and contactors as well as
power transmission & distribution.
Electric Technology
The R&D Center analyzes and researches core technologies related
to power equipment.
SCADA
The R&D Center carries out projects and technology research in the
fields of SCADA and DAS.
Simulator
The R&D Center predicts probable electrocution hazards by
conducting simulated analyses of power generation phenomena,
and develops simulation technologies and products that can
optimize the constituent facilities.
Short-Circuit Test / ACB Breaker Test
Environmental Test /
Non-stop High Temperature Test
Power Testing
& Technology Institute
PT&T is a KOLAS-qualified (Korea Laboratory
Accreditation Scheme) accredited testing laboratory
and provides worldwide testing service with its
1500MVA-capacity High Power Laboratory, High
Voltage Laboratory and Reliability Testing
Laboratory.
PT&T is also fully recognized by foreign testing and
certification bodies of high reputation as CESI of Italy,
KEMA of Netherlands, UL of America, etc. for its low
voltage testings.
Available Tests
- Electro-Mechanical Tests
- Insulation Performance Tests
- Short-Circuit Tests
- Reliability Evaluation Tests
- Arc Tests
- Environmental Tests
Research & Development

Testing Technology, Measuring & Analyzing Technology, Power
Equipment Monitoring & Diagnostic Techniques, Reliability
Testing & Evaluation Technology.
Solution provider
You can count on us.

New Face & New Resolution To become
a global leader that gives top priority to customer values
We promise you that LSIS will be reborn as a corporation that returns the best values
to its customers.
We are committed to global product development, driving future growth, and expanding
the overseas market share, as well as consolidating existing business.
Join us in a future where LSIS will become a genuine global leader.
Customer satisfaction with world-class products and services:

LSIS is committed to excellence!
Electric Power Industry |

Electric Equipment & Systems
The electric equipment and systems of LSIS, ranging from low to high
voltage products, have not only acquired ISO 9001 and 14001
certification for their efficient design and excellent quality, but many
other certificates, including KEMA, TV, CESI, ASTA, and KERI. The
outstanding quality of the products that we are manufacturing
conforms to international standards such as IEC, UL, ANSI, CCC, JIS,
and KS.
Cheongju Plant (Korea)
Busan Plant (Korea)
Dalian Plant (China)
Wuxi Plant (China)
We also provide Total Solutions that encompass customized designs

and more advanced technology, as well as efficient production and
installation, and highly accurate testing and analysis of power
equipment.
Hanoi Plant (Vietnam)
Automation Industry |
Automation Equipment, Industrial IT & RFID
LSIS, a leading pioneer of the domestic automation business,
developed the first ever PLC, Inverter (AC Drive), and DCS in Korean
automation history. We now provide Total Solutions through the
diverse application of our own products, ranging from controllers to
control systems that are based on sophisticated technology and
proven experience, to bring innovative change to distribution
systems and logistics.
Chonan Plant (Korea)
Wuxi Plant (China)
Susol LV circuit breakers
Low voltage
circuit breakers
Super Solution
Contents
Overview
A-1
Main characteristics
A-2
Accessories
A-3
Mounting & connection
A-4
Characteristics curves
A-5
Dimensions
A-6
Technical information
A-7
Design for technical strong point: The Susol MCCB
Ministry of Commerce
SuSol Series MCCB is available forworld best breaking capacity up to

150kA, and MS is seal structure for hidden electricity Arc.
SuSol product represents simultaneously simple and complicated
design for using cut diamond motive to emphasis on the hardness of
industrial product.
And we applied the identity of product image by designing same concept
MCCB and MS which is installed to cubicle.
SuSol Series acquire the competitive power through getting the picking
up GD product and wining IF Design Award.
>>>
Super Solution
For power distribution

The highest breaking capacity
Optimum coordination technique (Cascading & discrimination)
Powerful engineering tools
For protection of motor & its control device

Optimal overload protection
Guaranteed type-2 coordination between circuit breaker and
contactor, relay
For controlling and disconnecting circuits

For extensive applications
Wide range of optimized auxiliaries and accessories
Global Leading Products

Circuit breakers
For protection of power distribution
Circuit breakers
For protection of motor &
its control device
Disconnecting switches
For controlling and
disconnecting circuits
Super solution
Super Performance
Super Breaking capacity
Super Optimum coordination
Super Extensive applications
Susol TE, TD, TS series

Circuit breakers and Disconnecting switches
Susol circuit breakers provide superior

performance in a compact package. They
are used in cascade rated systems,
allowing the use of lower interruption
circuit breakers downstream, which lead
to lower system cost.
While meeting IEC60947-2 service and
interrupting ratings, these breakers
provide unmatched flexibility by
employing a wide variety of trip units

including fixed thermal & magnetic,
adjustable thermal-fixed magnetic,
adjustable thermal adjustable magnetic,
and electronic options.
Susol TE and TD circuit breaker is available
in one frame size in ratings from 16 to 160
amperes and TS circuit breakers are
available in three frame sizes in ratings
from 40 to 1600 amperes and in

interrupting capacities up to 150 kA at
415V AC.
Standard calibration is at 40C with
optional 55C factory calibration available
for applications where higher ambient
temperatures are encountered.
MCCB
Communication
Communication interface:RS485 (ModBUS)

Transmittable data :
Reading of protection settings
The highest current of the three phases
Measurement: R, S, T and N phase current (RMS)
Fault reading: Type of fault, Fault phase
The setting of communication address

By using TR button and LCD display (Ammeter)
ZSI Enable/Occurrence
Power source: DC24V Power is required
Providing optimal solution

Supervision PC
Sub_supervision PC
PLC
RS485 (DNP)
Communication unit
RS485 (Modbus)
Profibus-DP
Devices
MCCB(MODBUS) CU Profibus_DP PLC EtherNET Supervision PC

MCCB(MODBUS) PLC EtherNET Supervision PC
MCCB(MODBUS) CU RS485(DNP)
SUB_Supervision PC
MCCB(MODBUS) SUB_Supervision PC
MCCB
Residual Current Devices
Protection against earth leakage currents

The Susol circuit breaker can offer protection against earth leakage currents by using
an add-on residual current device (RCD). RCD unit interfaces directly below
the circuit breaker trip unit area without the use of any secondary wiring or connections

RTU23, RTU33 and RTU43 for TS type MCCBs
Apart from the protection against overloads typical of automatic circuit breakers, the residual
current circuit breaker derived from them also guarantee protection of people against earth
leakage currents, thereby ensuring protection against direct contacts, indirect contacts and fire
hazards.-(ELCB)
The RCD unit has numerous current and time settings and an override blocking the time settings
when set to 30mA. The earth leakage test button tests the electrical and
mechanical operation of the device. In order to allow for a dielectric test
of the breaker and RCD combination without damaging the electronics,
the dielectric plug is placed within the setting area.
The RCD unit may be equipped with an alarm
switch (FAL) to remotely
indicate tripping due to an earth leakage current.
Number of poles
RTU23
RTU33
RTU43
3*
3*
3*
TS100
TS160
Applicable
TS250
circuit breaker
TS400
TS630
TS800
Protection charicteristics
Sensitivity
In(A)
(adjustable)
(adjustable)
(adjustable)
0.03-0.3-1-3-10
0.03-0.3-1-3-10
0.03-0.3-1-3-10
Intentional time
(adjustable)
(adjustable)
(adjustable)
delay(ms)
0-60-150-300-600
0-60-150-300-600
0-60-150-300-600
Time delay **
Rated voltage
Max. breaking
(adjustable)
(adjustable)
(adjustable)
time(ms)
40-140-240-450-880
40-140-240-450-880
40-140-240-450-880
AC 50/60 Hz
220~460V / 460~690V
220~460V / 460~690V
220~460V / 460~690V
* 3P modules may also be used on 2P circuit breakers.

** If the sensitivity is set to 30mA, the time delay setting is reduced to zero.
MCCB
Main characteristics
Susol series circuit breakers

are suitable for
Protection of power distribution
Protection of motor & its control device
Controlling and disconnecting circuits
Optimum technical support for

(Cascading, Discrimination, Type 2 coordination)
Selecting economical protection system
Quarantee safety of the installation
Reducing the stress on components and damage
Guarantee service continuity
TE, TD, TS series Index
A-1. Overview
Range of LS low voltage circuit breakers
A-1-1
General
A-1-3
Standard & Approval
A-1-4
Structure
A-1-5
Marking and configuration
A-1-7
Overview of trip unit
A-1-9
Switching mechanism
A-1-11
Degree of protection
A-1-12
Ordering
A-1-13
Main switchboard
Type of circuit breaker
Rated current, In
Breaking capacity, Icu
Service breaking capacity (% Icu),Ics
Utilization category
Applied standard
ACB
MCCB
630~6300A
1000~1600A
65~150kA
50~150kA
100%
75~100%
A, B
IEC 60947-2
IEC 60947-2
Susol/Metasol
Susol
AH, AS, AN
TS
Image of circuit breaker
Brand name
Image of brand
Series
* 1pole MCCB
A-1-1
Main / Sub switchboard
Final distribution
MCCB
MCCB
MCB
16~800A
3~1200A
1~125A
37~150kA
10~85kA
6~10kA
100%
100%
50~100%
IEC 60947-2, UL489
IEC 60947-2
IEC60898, 60947-2, UL1077
Susol
Metasol
TE, TD, TS
AB series
BK series
A-1-2
General
Molded Case Circuit Breakers

The new series of Susol circuit-breakers is available in four frame sizes
: 160, 250, 630, 800, 1600AF
The breakers are able to cover a range of service currents up to 1600A and are available in the
fixed version and plug-in version.
The breaking capacities, at 380/415V, are classified by following letters:
S: 37kA for 100 and 160AF
N: 50kA for 160, 250 and 1600AF
65kA for 630 and 800AF
H: 75kA for 1600AF
85kA for 160, 250 and 630AF
100kA for 800AF
L: 150kA for 160, 250, 630, 800 and 1600AF
Susol circuit-breakers are climate-proof. The breakers are intended for use in rooms where there
are no excessive operating conditions (e.g. dust, corrosive vapors, gases).
If the circuit-breakers are used in dusty or humid locations, suitable enclosures should be provided.
Sufficient fresh air supply must be provided if there are harmful gases (e.g. hydrogen-sulfide vapor)
in the ambient air.
All Susol circuit breakers offer positive contact indication and are suitable for isolation in
compliance with standards IEC 60947-1 and 2.
Susol circuit-breakers are suitable for protection of
- Power distribution systems supplied by transformers or generators
- Motor and generator
A switch-disconnector of Susol circuit breakers is available for for circuit control and isolation.
A-1-3
Standards & Approval
Susol series circuit breakers and

auxiliaries comply with the following international standard:
IEC 60947-1
Low-voltage switchgear and controlgear
- Part 1: General rules
IEC 60947-2
- Part 2: Circuit-breakers
IEC 60947-3
- Part 3: Switches, disconnectors, switchdisconnectors and fuse-combination units
IEC 60947-4
- Part 4-1: Contactors and motor-starters
Electromechanical contactors and motor starters Switches, disconnectors, switchdisconnectors
AC semiconductor motor controllers and starters
AC semiconductor controllers and contactors for non-motor loads
The following certificates are available on a request.
- CE Declaration of conformity
- Certificate of conformance test (CB) - IEC 60947
- Full type test report issued by KEMA
- Certificate of conformance test - CCC (China)
- Letter of origin
CE conformity marking
The CE conformity marking shall indicate conformity to all the obligations imposed on the
manufacturer, as regards his products, by virtue of the European Community directives providing
for the affixing of the CE marking.
When the CE marking is affixed on a product, it represents a declaration of the manufacturer or of
his authorized representative that the product in question conforms to all the applicable provisions
including the conformity assessment procedures. This prevents the Member States from limiting
the marketing and putting into service of products bearing the CE marking, unless this measure is
justified by the proved non-conformity of the product.
IECEE CB SCHEME
The IECEE CB Scheme is the world's first truly international system for acceptance of test reports
dealing with the safety of electrical and electronic products. It is a multilateral agreement among
participating countries and certification organizations. A manufacturer utilizing a CB test report
issued by one of these organizations can obtain national certification in all other member countries
of the CB Scheme.
The Scheme is based on the use of international (IEC) Standards. If some members' national
standards are not yet completely harmonized with IEC Standards, national differences are
permitted if clearly declared to all other members. The CB Scheme utilizes CB Test Certificates to
attest that product samples have successfully passed the appropriate tests and are in compliance
with the requirements of the relevant IEC Standard and with the declared national differences of
various member countries.
The main objective of the Scheme, is to facilitate trade by promoting harmonization of the national
standards with international Standards and cooperation among product certifiers worldwide in order
to bring product manufacturers a step closer to the ideal concept of "one product, one test, one
mark, where applicable'.
A-1-4
Structure
The primary components are: a switching mechanism, an automatic tripping device

(and manual trip button), contacts, an arc-extinguishing device, terminals and a molded case.
Mechanism unit
Unvarying contact force
regardless of over travel
RTA (Rapid Toggle Area)
Open speed of moving contact is
rapid by optimized cam curve
regardless of trip signal
Force
Optimized cam curve
Angle
Unvarying contact force
A-1-5
Structure
Molded case
UL94 V-0 flame retarded
High strength
Trip button (push to trip)

Enables tripping mechanically
from outside, for confirming the
operation of the accessory
switches and the manual
resetting function.
Handle
Function of indications
- ON OFF TRIP
Resetting
When the handle indicates "tripped"
position it must first be reset by moving
the handle to the OFF position and
then closing is possible
Trip-Free even if the handle is held at
ON, the breaker will trip if an over
current flows
Suitable for Verification of the main
contact position under abnormal
conditions because the handle doesnt
indicate open position
Note) Fault Alarm Switch, FAL is not operated by trip button.

FAL is applicable only to the breakers with electronic trip units.
Arc-Extinguishing unit
PASQ Type Quenching Chamber
Very superior to increasing arc
voltage during short time
PASQ ;
- Puffer Assisted Self-Quenching
- Patented by LSIS
Hybrid
chamber
Grid
Assy
A-1-6
Rated frequency
Symbol indicating
suitability for isolation
as defined by IEC 947-2
A-1-7
Standard
Manufacturer
Model (Rating and breaking capacity)

TS: Series
250: Max. Ampere rating
S: Standard
N: Normal (Standard)
H: High
L: Current limiting
Standardized characteristics:
Ui: Rated insulation voltage
Uimp: Impulse withstand voltage
Ue: Rated operational voltage
Icu: Ultimate breaking capacity
Ics: Service breaking capacity
Product: Molded Case Circuit Breaker
160AF
250AF
630AF
800AF
1600AF
TE100S
TE160S
TE100N
TE160N
TD100N
TD160N
TS100N
TS160N
TS250N
-
TS400N
TS630N
-
TS800N
-
TS1000N
TS1250N
TS1600N
-
TD100H
TD160H
-
TS100H
TS160H
TS250H
TS400H
TS630H
-
TS800H
-
TS1000H
TS1250H
TS1600H
TD100L
TD160L
-
TS100L
TS160L
TS250L
TS400L
TS630L
-
TS800L
-
TS1000L
-
37kA
50kA
50kA
65kA
65kA
50kA
85kA
85kA
85kA
100kA
70kA
150kA
150kA
150kA
150kA
150kA
Upstream connections
Fixing hole
Certificate plate
Indication of closed (I/ON) position
Brand name
Operating handle
Indication of open (O/OFF) position

Company logo
"push to trip" button
Rating of trip unit

Trip unit
Fixing hole
Downstream connections
A-1-8
Overview of trip units
On Susol circuit breakers, the thermal-magnetic and electronic trip units are interchangeable and
may be rapidly fitted to the circuit breakers.
It is therefore easy to change the protection of a given circuit following a modification in an
installation. On TS400 and 630 circuit breakers, the electronic trip units are interchangeable plug-in
modules. Trip unit ETM offers a large number of protection settings.
Each Trip devices has different types of protection depending on the associated trip unit:
Standard protection
Protection of networks supplied by line distribution
Protection of long cables
Protection of DC networks
Protection of motor-starters
Service connection circuit breaker (for special subscriber contracts)
Susol TD100, TD160 circuit breakers may be equipped with either FTU or FMU.
The trip units are not interchangeable types and can be supplied only after fixed with circuit breakers.
Ampere ratings
MCCB frame type
Rated current, In[A]
Type of
trip unit
TE100
TD100
TE160
Built in unit
TS100
TS250
FTU
FMU
16, 20, 25, 32, 40, 16, 20, 25, 32, 40,
TD160
TS160
Thermal magnetic release
Inter
changeable
50, 63, 80, 100
50, 63, 80, 100
100, 125, 160
100, 125, 160
40, 50, 63,
40, 50, 63,
80, 100
80, 100
100, 125, 160
100, 125, 160
Electronic release
MTU
ETS
ETM
160
40, 80
100
40, 80, 160
160
250
125, 160
32, 50, 63,

100, 160
100, 160, 220
40, 80, 160, 250
300, 400
300, 400
320
160, 250, 400
160, 250, 400
TS630
500, 630
500, 630
500, 630
500
TS800
700, 800
800
800
630
trip unit
125, 160, 200, 250 125, 160, 200, 250 125, 160, 200, 250
1.6, 3.2, 6.3, 12,

20, 32, 50, 63, 100
300, 400
TS400
160, 250, 400, 630 160, 250, 400, 630

630, 800
Types of trip units

FTU
FMU
ATU
MTU
ETS
ETM
DSU
A-1-9
DSU
ATU
Fixed thermal, Fixed magnetic

Adjustable thermal, Fixed magnetic
Adjustable thermal, Adjustable magnetic
Magnetic only
Electronic (LSI)
Electronic (LSIG, Ammeter, Communication, Zone selective interlocking)
Disconnecting switch
630, 800
400
630
800
Overview of trip units
FTU
Fixed-thermal, fixed-magnetic
FTU
Im=2500A
Ir
Electronic
trip unit
Im
FMU
Adjustable-thermal, fixed-magnetic
ATU
Adjustable-thermal, adjustable-magnetic
Thermal magnetic
trip unit
ATU
Trip unit identification
0.9
0.8
7
1
Ir
TS250
9
5
10
1848
2112
Im
FMU
MTU
Magnetic only
MTU
Trip unit function
1584
1320
2376
2640
Im
220A
3P
MCCB frame type

DSU
Disconnecting switch
DSU
3P
FTU
ATU
ETS
Electronic (LSI)
ETM
Electronic (LSIG, multi-function unit)
ETM
A-1-10
Switching mechanism
Double contactor structure
Optimize
ON position
Repulsion force
Shape of contactor
Induce easily the arc mobility to grid
direction
Rapidly redeploy the arc from moving
contactor
Prevent contact tip from erosion
Unvarying contact force regardless of

over travel
Open speed of moving contact is rapid by
optimized cam curve regardless of trip
signal
Function of trip free
Optimized
cam curve
Unvarying
contact
Force
Open speed & contact force
Angle
Fig. 3 ON position
OFF position
Push to trip in OFF position
* Reset pin moment < Main spring moment
Stability of endurance
Fig. 4 OFF position
Stress Amplitude (MPa)
600.0
500.0
400.0
300.0
200.0
100.0
0.0
0.00E+00
4.00E+06
3.00E+06
1.20E+07
1.60E+07
2.00E+07
Life
TRIP position
Enables tripping mechanically from
outside, for confirming the operation of
the accessory switches and the manual
resetting function
Fig. 5 TRIP position
A-1-11
The table indicates the degrees of protection guaranteed by Susol circuit-breakers according to
several type of installation. Basically, the fixed parts are always preset with IP20 degree of
protection.
IP65 degree of protection can be obtained with the circuit-breaker installed in a switchboard fitted
with an extended rotary handle operating mechanism transmitted on the compartment door.
IP
Protection of
persons against
access to hazardo
us parts with:
IP20
Wire
IP30
Wire
IP20
or
IP30
Wire
The access probe of 1.0mm

shall not penetrate.
IP40
Wire
Circuit breaker with

cover frame and
motor operator

diameter shall not penetrate.
IP40
Wire

cover frame and
rotary direct handle

IP40
Wire
IP65
Wire
Type
Circuit breaker

terminal cover
Plug-in circuit breaker
Full penetration of 12.5mm diameter

sphere not allowed.
The jointed test finger shall have
adequate clearance from hazardous
parts
The access probe of 2.5mm diameter

shall not penetrate.
Full penetration of 12.5mm diameter sphere

not allowed. The jointed test finger shall have
adequate clearance from hazardous parts.
* When the circuit breaker is installed and the
supplied covers are mounted.

cover frame for door
cutout
Circuit breaker
Totally protected
with cover frame
against ingress of
and rotary
dust and water jets fromany direction
extended handle
A-1-12
Ordering
Susol TE, TD, TS up to 800AF MCCB
Trip unit: FTU, ATU, FMU, ETS, ETM
TS250
Ampere frame
FTU
Type
250
Rated current
Poles
100
Standard
2P
2Pole
160
Normal
3P
3Pole
100
High
4P*
4Pole
160
Current limit
TE
TD
Standard
Plug-in
AX
Accessories
Note) Please refer to A-3
Note) Plug in type is only

available 3Pole
Note) 4Pole MCCB of TS100 to 800A have N-R-S-T

and R-S-T-N both N phase way. Electric trip
unit type is only available 3Pole
100
Trip unit
160
TS
250
400
630
800
Thermal FTU
magnetic FMU
trip unit ATU
Fixed Trip Unit
Electronic ETS
trip units ETM
Electronic Trip Unit Standard
Fixed Magnetic Trip Unit

Adjustable Trip Unit
Electronic Trip Unit Multi Function
Trip unit: MTU
TS250
Ampere frame
TS
Type
100
160
High
250
Current limit
400
630
800
Normal
MTU
220
Magnetic only
trip unit
Rated current
Poles
3P
AF
Rated current
TS100 1.6, 3.2, 6.3, 12, 20, 32, 50, 63, 100
TS160 32, 50, 63, 80, 100, 160
TS250 100, 160, 220
TS400 320
TS630 500
TS800 630
A-1-13
3Pole
Standard
Plug-in
AX
Accessories
Note) Please refer to A-3
Trip unit: DSU
TS250
NA
DTU
250
Ampere frame
MCCB
Disconnect
Switch Unit
Rated current
Poles
TD
160
3P
3Pole
Standard
Plug-in
100
160
TS
250
400
630
800
AF
Rated current
TD160
160
TS100
100
TS160
160
TS250
250
TS400
400
TS630
630
TS800
800
A-1-14
Ordering
Susol TS 1600AF MCCB
TS1600
Ampere frame
TS
1600A
Trip relay
Poles
1000
Normal
3P
3Pole
1250
Ammeter
4P
4Pole
Connection type
-
Standard
Rear
REAR
1600
Type
Power meter
Supreme meter
Connection
Rated current
N phase way (4Pole)
Normal
800A
N-R-S-T
High
1000A
R-S-T-N
Current limit
1250A
Switch-
1600A
NA
disconnector
A-1-15
Trip relay
Trip relay type
Communication & protection
Control voltage & frequency
000 Without trip relay

N
N
Normal
Without comm. + L/S/I/G
* L/S/I/G configuration as standard

-with LED indicators
-without output contacts
* Ground fault system by vector sum
A
A
Ammeter
Self-Power, 60Hz
Self-Power, 50Hz
Without comm.
Self-Power, 60Hz
Without comm. + Earth leakage
AC/DC 100V~250V, 60Hz
Without comm. + Earth leakage
DC 24V~60V, 60Hz
Comm.
Self-Power, 50Hz
Comm. + Earth leakage
AC/DC 100V~250V, 50Hz
DC 24V~60V, 50Hz

* Ground fault system by vector sum(G,C)
* Earth leakage system
- Z,K: External CT - LS ZCT applied(fault current 0.5~30A, 1600AF)
- E,X: External CT - Private ZCT applied(fault current >30A)
* Comm. And output contacts DO NOT work under self-power condition.
(Only checking LED available)
P
P
Power meter
Comm.
AC/DC 100V~250V, 60Hz
DC 24V~60V, 60Hz
AC/DC 100V~250V, 50Hz
Comm. + Pre-trip alarm
DC 24V~60V, 50Hz

- K: External CT - LS ZCT applied(fault current 0.5~30A, 1600AF)
- X: External CT - Private ZCT applied(fault current >30A)
* Applicable to generator protection purpose
S
S
Supreme meter
Comm.
AC/DC 100V~250V, 60Hz
DC 24V~60V, 60Hz
AC/DC 100V~250V, 50Hz
Comm. + Pre-trip alarm
DC 24V~60V, 50Hz

- K: External CT - LS ZCT applied(fault current 0.5~30A, 1600AF)
- X: External CT - Private ZCT applied(fault current >30A)
* Applicable to generator protection purpose
Note) 1. L/S/I/G configuration as standard
2. Ground fault, earth leakage and pre-trip alarm functions are alternative.
3. The functions like Metering, Communication, ZSI, Remote reset and Digital output are NOT available only under Self-power condition.
4. Voltage module should be required for P and S types(supplied separately)
A-1-16
A-2. Main characteristics

MCCBs for power distribution up to 800A
Electrical characteristics
Thermal magnetic trip unit
Overview
FTU, FMU for TE100, TE160, TD100, TD160
FTU, FMU for TS100, TS160, TS250
ATU for TS160, TS250
FTU, FMU, ATU for TS400, TS630
FTU, FMU, ATU for TS800
A-2-1
A-2-3
A-2-5
A-2-7
A-2-11
A-2-15
Electronic trip units (Standard)

Overview
ETS23 for TS100, TS160, TS250
ETS33 for TS400, TS630
ETS43 for TS800
A-2-17
A-2-19
A-2-25
A-2-31
Electronic trip units (Multifunction)

Overview
ETM33 for TS400, TS630
ETM43 for TS800
A-2-37
A-2-40
A-2-49
MCCBs for motor protection

Magnetic only trip unit
A-2-57
A-2-59
Switch-Disconnectors
Susol MCCB for DC Application

4 pole MCCB with electronic trip unit
A-2-61
A-2-63
A-2-63

OCR(Over current relays) Trip unit
A-2-65
Overview
N(Normal), NV type
A(Ammeter) type
P(Power meter) type
S(Supreme meter) type
Operation characteristic
Measurement function
ZSI -Zone Selective Interlocking (A, P, S type)
Remote reset and digital I/O (A, P, S type)
Communication
Event & fault recording (P, S type)
System information
System block diagram
Installation and Handling
A-2-66
A-2-67
A-2-69
A-2-71
A-2-73
A-2-75
A-2-77
A-2-78
A-2-79
A-2-80
A-2-81
A-2-81
A-2-82
A-2-83
MCCBs for power distribution

Frame size
Rated current, In
No. of poles
Rated operational
AC
voltage, Ue
DC
Rated impulse withstand voltage, Uimp
Rated insulation voltage, Ui
Rated ultimate short-circuit breaking capacity, Icu
AC 50/60Hz
220/240V
DC
TE100
TE160
TD100
TD160
100
160
100
[A]
16~100
100,125,160
16, 20, 25, 32, 40,

50, 63, 80, 100
160
1P: 16, 20, 25, 32,
40, 50, 63, 80,
100,125, 160
2, 3P: 100, 125, 160
[V]
[V]
[kV]
[V]
3,4
690
500
8
750
3,4
690
500
8
750
[AF]
1, 2, 3, 4
240(1P), 690
250(1P), 500
8
750
N
L
N
H
L
30(1P) 50(1P)
85
100 200
200
85
100
50
85
150
50
85
150
50
70
130
50
70
130
30
50
65
30
50
65
5
8
10
5
8
10
16(1P) 25(1P)
42
65
100
100
42
65
42
65
100
42
65
100
100% 100% 100% 100% 100% 100%
[kA]
50
85
50
85
380/415V
440/460V
480/500V
660/690V
[kA]
[kA]
[kA]
[kA]
37
25
18
6
50
37
25
8
37
25
18
6
50
37
25
8
250V
[kA]
37
50
37
50
37
100%
50
100%
37
100%
50
100%
105
187
105
187
187
220
440
77.7
52.5
36
9.2
105
77.7
52.5
13.6
77.7
52.5
36
9.2
105
77.7
52.5
13.6
105
105
63
8
330
286
143
17
500V(2poles in series) [kA]

Rated service breaking capacity, Ics
[%Icu]
Rated short-circuit making capacity Icm
AC 50/60Hz
220/240V
[kA]
380/415V
440/460V
480/500V
660/690V
[kA]
[kA]
[kA]
[kA]
Category of utilization
Isolation behavior
Trip unit (release)
Thermal-Magnetic
fixed-thermal, fixed-magnetic
FTU
adjustable-thermal, fixed-magnetic
FMU
adjustable-thermal, adjustable-magnetic
ATU
magnetic only
MTU
Electronic
LSI
ETS
LSI
ETM
Option Earth-fault protection, Ig
Zone selective interlocking, ZSI
Ammeter
Communication
Earth-leakage protection module
Connection
fixed
front-connection
rear-connection
plug-in
front-connection
rear-connection
Mechanical life
[operations]
Electrical life @ 415 V AC
[operations]
Basic dimensions, WHD 1-pole
[mm]
(front connection)
3-pole
[mm]
4-pole
[mm]
Weight
1-pole
[kg]
(front connection)
3-pole
[kg]
4-pole
[kg]
Reference standard
A-2-1
2, 3, 4
690
500
8
750
H
187
154
105
14
A
25000
10000
7613082
10113082
1.05
1.35
IEC60947-2
25000
10000
7613082
10113082
1.05
1.35
IEC60947-2
25000
10000
9014086
12014086
1.5
1.8
IEC60947-2
Applicable to MCCBs equipped with FTU, FMU, ATU

2 pole MCCB in 3pole frame size
105(1P)
187
105
105
63
8
105(1P)
220
187
154
105
14
A
440
330
286
143
17
25000
10000
3514086
9014086
12014086
0.57
1.5
1.8
IEC60947-2
700A only available for TS800FTU

Not applicable to 1pole
TS100
TS160
TS250
TS400
TS630
TS800
100
160
250
400
630
800
300, 400
500, 630
700, 800
2, 3, 4
690
500
8
750
H
2, 3, 4
690
500
8
750
H
40, 50, 63, 80, 100
2, 3, 4
690
500
8
750
H
100
120
50
50
42
10
(100), 125, 160
125, 160, 200, 250
2, 3, 4
690
500
8
750
H
2, 3, 4
690
500
8
750
H
2, 3, 4
690
500
8
750
H
200
100
120
200
100
120
200
100
120
200
100
120
200
100
120
200
85
70
65
15
150
130
85
20
50
50
42
10
85
70
65
15
150
130
85
20
50
50
42
10
85
70
65
15
150
130
85
20
65
65
42
10
85
85
65
20
150
130
85
35
65
65
42
10
85
85
65
20
150
130
85
35
65
65
42
10
100
100
85
20
150
130
100
35
50
85
100
50
85
100
50
85
100
50
85
100
50
85
100
50
85
100
50
100%
85
100%
220
264
440
220
264
440
220
264
440
220
264
440
220
264
440
220
264
440
105
105
88
17
187
154
143
30
A
330
286
187
40
105
105
88
17
187
154
143
30
A
330
286
187
40
105
105
88
17
187
154
143
30
A
330
286
187
40
143
143
88
17
187
187
143
40
A
330
286
187
74
143
143
88
17
187
187
143
40
A
330
286
187
74
143
143
88
17
220
220
187
40
A
330
286
220
74
100
50
85
100
100% 100% 100% 100%
50
100%
85
100
100% 100%
25000
10000
10516086
14016086
2
2.6
IEC60947-2
25000
10000
10516086
14016086
2
2.6
IEC60947-2
25000
10000
10516086
14016086
2
2.6
IEC60947-2
50
85
100
50
100% 100% 100% 100%
20000
6000
140260110
186.5260110
5.4
7.2
IEC60947-2
85
100
100% 100%
20000
6000
140260110
186.5260110
5.4
7.2
IEC60947-2
50
85
100% 100%
100
100%
10000
3000
210320135
280320135
15.1
19.6
IEC60947-2
The trip unit ATU is available from 125A
A-2-2

Thermal magnetic trip units
Overview
Susol series circuit breakers can be installed with thermal magnetic trip units.
And, there are two kinds of trip units according to way of installation as follows.
Built-in trip units for TE and TD series upto 160A
Interchangeable trip units for TS series upto 800A
Function
Protection of power distribution
Overload protection: Thermal protection with a fixed or adjustable threshold
Short-circuit protection: Magnetic protection with a fixed or adjustable pick-up
Protection of the fourth pole
4P3T type (neutral unprotected)
4P4T type 50% (neutral protection at 0.5In)
4P4T type 100% (neutral protection at 1In)
Operation
Trip bar
ATU
Bimetal
Armature
Thermal magnetic types

Time-Delay operation
An overcurrent heats and warps the bimetal to actuate the
trip bar by the bimetal characteristic.
Instantaneous operation
If the overcurrent is excessive, the armature is attracted
and the trip bar actuated by electromagnetic force.
Ratings
Ratings(A)
Thermal magnetic trip units(FTU/FMU/ATU)

at 40
In
20
25
32
40
50
63
80
100
125
160
300
400
500
630
800
TE100
TD100
TE160
TD160
TS100
TS160
TS250
TS400
TS630
TS800
Note) Rated current 700A is available for TS800FTU.
A-2-3
TE100 to TS800
16
200 250

Overview
Characteristics
Fixed thermal, fixed magnetic trip units
FTU
Fixed thermal
16A ... 800A rated currents
Fixed magnetic
400A ... 8000A tripping currents
Applicable to TE100 ... TS800 frames
FTU
Im=2500A
Ir
Im
Adjustable thermal, fixed magnetic trip units

FMU
Adjustable thermal
Adjustable : 0.8~1In
Fixed magnetic
Applicable to TE100 ... TS800 frames
Adjustable thermal, adjustable magnetic trip units

ATU
Adjustable thermal
Adjustable : 0.8~1In
Adjustable magnetic
Adjustable : 5~10In
Applicable to TS160 ... TS800 frames
ATU
0.9
0.8
9
5
Ir
10
Im
A-2-4

FTU, FMU for TE100, TD100, TE160, TD160
Configuration
Ratings (A), In at 40C

Number of pole
Short circuit protection (magnetic)

Setting current, Im
Overload protection (thermal)

Setting current, Ir
TE100 FTU, TD100 FTU, TE160 FTU, TD160 FTU

- Fixed thermal & magnetic trip unit
FTU
Im=1600A
160A
TE100 FTU, TD100 FTU,

TE160 FTU, TD160 FTU
t
0.9
0.8
Ir Im
TE100 FMU, TD100 FMU, TE160 FMU, TD160 FMU

- Adjustable thermal & fixed magnetic trip unit
0.9
FMU
0.8
Im=1600A
160A
Ir Im
Catalogue numbering system

TD160
FMU
Trip unit function
- FTU : Fixed thermal & magnetic unit
- FMU : Adjustable thermal, fixed magnetic unit
MCCB frame type
- TE100 : TE100N, TE100H, TE100L
- TD100 : TD100N, TD100H, TD100L
- TE160 : TE160N, TE160H, TE160L
- TD160 : TD160N, TD160H, TD160L
A-2-5
Ir
Im

FTU, FMU for TE100, TD100, TE160, TD160
Characteristics
Thermal magnetic trip units(FTU/FMU) ... TE100, TD100, TE160, TD160
Rating(A)
at 40 In
16
20
25
32
40
50
63
80
100
125
160
TE/TD100
TE/TD160
Overload protection(thermal)
Current setting(A) Ir
FTU
Fixed
FMU
Adjustable 0.8, 0.9, 1In (3 settings)
Short - circuit protection(magnetic)

Current setting(A) Im
FTU
Fixed 400A
Fixed 10In
FMU
Fixed 400A
Fixed 10In
Protection of N pole
4P3T
Neutral No protection
4P4T
Neutral protection (100% Ir)
Setting details
Thermal overload protection
Trip unit type
Trip unit rating, In (A)
Setting
Ir
16
20
TE/TD100FTU
Fixed
16
20
TE/TD100FMU
0.8
12.8
16
20
25.6
32
40
50.4
64
80
0.9
14.4
18
22.5
28.8
36
45
56.7
72
90
16
63
25
32
25
32
40
50
40
50
63
63
80
100
125
160
80
100
20
25
32
40
50
80
100
TE/TD160FTU
Fixed
100
125
TE/TD160FMU
0.8
80
100
128
0.9
90
112.5
144
100
125
160
160
Magnetic short-circuit protection

Trip unit type
Setting
current, Ir
16
20
25
32
40
50
63
80
100
125
160
In10
400
400
400
400
400
500
630
800
1000
0.8In
Fixed
In10
400
400
400
400
400
500
630
800
1000
0.9In
Fixed
In10
400
400
400
400
400
500
630
800
1000
1000
1.0In
Fixed
In10
400
400
400
400
400
500
630
800
Fixed
In10
1000 1250 1600
0.8In
Fixed
In10
1000 1250 1600
0.9In
Fixed
In10
1000 1250 1600
1.0In
Fixed
In10
1000 1250 1600
TE/TD160FTU
TE/TD160FMU
current, Im
Fixed
TE/TD100FTU
TE/TD100FMU
Setting
A-2-6

Configuration

Number of pole

Setting current, Im

Setting current, Ir
TS100 FTU, TS160 FTU, TS250 FTU

- Fixed thermal fixed magnetic trip unit
TS100 FMU, TS160 FMU,

TS250 FMU
FTU
Im=2500A
Ir
Im
TS100 FMU, TS160 FMU, TS250 FMU

- Adjustable thermal fixed magnetic trip unit
TS160 ATU, TS250 ATU

t
Short circuit protection

(magnetic)
0.9
0.8

- Adjustable thermal adjustable magnetic trip unit

(magnetic)
7
ATU
0.9
0.8
Ir
Im
10
9
5
A-2-7
8
9
10
Ir
Im

Characteristics
Thermal Magnetic trip units(FTU/FMU/ATU) ... TS100 to TS250
Rating(A)
at 40 In
TS100
TS160
TS250
40
50
63
80
100
125
160
200
250
FTU
FMU
ATU
Fixed
Adjustable 0.8 toIn
Adjustable 0.8 toIn

FTU
FMU
ATU
Fixed 10In
Fixed 10In
Adjustable 5, 6, 7, 8, 9, 10In (6 settings)
4P3T
4P4T

TS250
FTU
Trip unit function
- FTU: Fixed thermal, fixed magnetic unit
MCCB frame type
- TS100: TS100N, TS100H, TS100L
- TS160: TS160N, TS160H, TS160L
- TS250: TS250N, TS250H, TS250L
TS250
FMU
Trip unit function
- FMU: Adjustable thermal, fixed magnetic unit
MCCB frame type
- TS100: TS100N, TS100H, TS100L
- TS160: TS160N, TS160H, TS160L
- TS250: TS250N, TS250H, TS250L
TS250
ATU
Trip unit function
- ATU: Adjustable thermal, adjustable magnetic unit
MCCB frame type
- TS160: TS160N, TS160H, TS160L
- TS250: TS250N, TS250H, TS250L
The trip unit ATU is available from 125A
A-2-8

Setting details
Trip unit type
TS100FTU
TS100FMU
TS160FTU
TS160FMU
TS160ATU
TS250FTU
TS250FMU
TS250ATU
A-2-9
Setting
Ir

40
50
63
80
100
125
160
200
250
Fixed
40
50
63
80
100
0.8In
32
40
50
64
80
0.9In
36
45
57
72
90
1.0In
40
50
63
80
100
Fixed
100
125
160
0.8In
80
100
128
0.9In
90
113
144
1.0In
100
125
160
0.8In
100
128
0.9In
113
144
1.0In
125
160
Fixed
125
160
200
250
0.8In
100
128
160
200
0.9In
113
144
180
225
1.0In
125
160
200
250
0.8In
100
128
160
200
0.9In
113
144
180
225
1.0In
125
160
200
250

Setting details
Trip unit type
Setting
current, Ir
TS100FTU
TS100FMU
0.8In
0.9In
1.0In
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
0.8In
Adjustable
0.9In
Adjustable
1.0In
Adjustable
0.8In
0.9In
1.0In
Fixed
Fixed
Fixed
Fixed
0.8In
Adjustable
0.9In
Adjustable
1.0In
Adjustable
0.8In
0.9In
1.0In
TS160FTU
TS160FMU
TS160ATU
TS250FTU
TS250FMU
TS250ATU
Setting
current, Im
In10
In10
In10
In10
In10
In10
In10
In10
In5
In6
In7
In8
In9
In10
In5
In6
In7
In8
In9
In10
In5
In6
In7
In8
In9
In10
In10
In10
In10
In10
In5
In6
In7
In8
In9
In10
In5
In6
In7
In8
In9
In10
In5
In6
In7
In8
In9
In10

40
400
400
400
400
-
50
500
500
500
500
-
63
630
630
630
630
-
80
800
800
800
800
-
100
1000
1000
1000
1000
1000
1000
1000
1000
-
125
1250
1250
1250
1250
625
750
875
1000
1125
1250
625
750
875
1000
1125
1250
625
750
875
1000
1125
1250
1250
1250
1250
1250
625
750
875
1000
1125
1250
625
750
875
1000
1125
1250
625
750
875
1000
1125
1250
160
1600
1600
1600
1600
800
960
1120
1280
1440
1600
800
960
1120
1280
1440
1600
800
960
1120
1280
1440
1600
1600
1600
1600
1600
800
960
1120
1280
1440
1600
800
960
1120
1280
1440
1600
800
960
1120
1280
1440
1600
200
-
250
-
2000
2000
2000
2000
1000
1200
1400
1600
1800
2000
1000
1200
1400
1600
1800
2000
1000
1200
1400
1600
1800
2000
2500
2500
2500
2500
1250
1500
1750
2000
2250
2500
1250
1500
1750
2000
2250
2500
1250
1500
1750
2000
2250
2500
A-2-10

Configuration

Number of pole
Setting current, Im

Setting current, Ir
TS400 FTU, TS630 FTU

TS400 FMU, TS630 FMU
FTU
Im=6300A
Ir
0.9
630A
0.8
Im
TS400 FMU, TS630 FMU

0
Ir
Im
FMU
0.9
0.8
630A
Im=6300A
1
Ir
Im
t
0.9
0.8

ATU
6
0.9
0.8
7
6
A-2-11
Im
9
5
10
9
5
Ir
630A
10
Ir
Im

Characteristics
Thermal Magnetic trip units(FTU/FMU/ATU) ... TS400 to TS630
Rating(A) at 40 In
300
400
500
630
TS400
TS630
FTU
In=Ir (Fixed)
FMU
ATU

FTU
Fixed 10In
FMU
Fixed 10In
ATU
Adjustable 5, 6, 7, 8, 9,10In(6 settings)
4P3T
4P4T

TS630
ATU
Trip unit function
- FMU : Adjustable thermal & fixed magnetic unit
- ATU : Adjustable thermal & adjustable magnetic unit
MCCB frame type
- TS400 : TS400N, TS400H, TS400L
- TS630 : TS630N, TS630H, TS630L
A-2-12

Setting details
Trip unit type
TS400FTU
TS400FMU
TS400ATU
TS630FTU
TS630FMU
TS630ATU
A-2-13
Setting
Ir
300
400
500
630
Fixed
300
400
0.8
240
320
0.9
270
360
300
400
0.8
240
320
0.9
270
360
300
400
Fixed
500
630
0.8
400
504
0.9
450
567
500
630
0.8
400
504
0.9
450
567
500
630

Setting details
Trip unit type
Setting
current, Ir
TS400FTU
TS400FMU
0.8In
0.9In
1.0In
0.8In
TS400ATU
0.9In
1.0In
TS630FTU
TS630FMU
0.8In
0.9In
1.0In
0.8In
TS630ATU
0.9In
1.0In
Setting
current, Im
Fixed
In10
Fixed
In10
Fixed
In10
Fixed
In10
In5
In6
In7
Adjustable
In8
In9
In10
In5
In6
In7
Adjustable
In8
In9
In10
In5
In6
In7
Adjustable
In8
In9
In10
Fixed
In10
Fixed
In10
Fixed
In10
Fixed
In10
In5
In6
In7
Adjustable
In8
In9
In10
In5
In6
In7
Adjustable
In8
In9
In10
In5
In6
In7
Adjustable
In8
In9
In10

300
3000
3000
3000
3000
1500
1800
2100
2400
2700
3000
1500
1800
2100
2400
2700
3000
1500
1800
2100
2400
2700
3000
-
400
4000
4000
4000
4000
2000
2400
2800
3200
3600
4000
2000
2400
2800
3200
3600
4000
2000
2400
2800
3200
3600
4000
-
500
5000
5000
5000
5000
2500
3000
3500
4000
4500
5000
2500
3000
3500
4000
4500
5000
2500
3000
3500
4000
4500
5000
630
6300
6300
6300
6300
3150
3780
4410
5040
5670
6300
3150
3780
4410
5040
5670
6300
3150
3780
4410
5040
5670
6300
A-2-14

Configuration

Number of pole

Setting current, Im

Setting current, Ir
TS800 FTU
TS800 FMU
FTU
0.9
Im=8000A
Ir
800A
0.8
Im
TS800 FMU
0
FMU
0.9
0.8
Im=8000A
1
Ir
800A
Im
Ir
Im
TS800 ATU
t
0.9
0.8
TS800 ATU
ATU
0.9
0.8
7
6
800A
10
10
0
Im
Ir
Im
ATU
Trip unit function
- FMU : Adjustable thermal & fixed magnetic unit
- ATU : Adjustable thermal & adjustable magnetic unit
MCCB frame type
- TS800 : TS800N, TS800H, TS800L
A-2-15
9
5

TS800
9
5
Ir

Characteristics
Thermal Magnetic trip units(FTU/FMU/ATU) ... TS800
700 (1)
Rating(A) at 40 In
TS800
800

FTU
Fixed 10In
FMU
Fixed 10In
ATU
Adjustable 5, 6, 7, 8, 9, 10In (6 settings)
FTU
Fixed
FMU
Adjustable 0.8, 0.9,1In (3 settings)
4P3T
ATU
Adjustable 0.8, 0.9,1In (3 settings)
4P4T
Note1) Only available for TS800FTU
Setting details
Trip unit type
TS800FTU
TS800FMU
TS800ATU
Setting
Ir
700
800
Fixed
0.8
0.9
1
700
-
800
640
720
800
0.8
0.9
1
640
720
800

Trip unit type
Setting
current, Ir
TS800FTU
TS800FMU
0.8In
0.9In
1.0In
0.8In
TS800ATU
0.9In
1.0In
Setting
current, Im
Fixed
In10
Fixed
In10
Fixed
In10
Fixed
In10
In5
In6
In7
Adjustable
In8
In9
In10
In5
In6
In7
Adjustable
In8
In9
In10
In5
In6
In7
Adjustable
In8
In9
In10

700
7000
-
800
8000
8000
8000
8000
4000
4800
5600
6400
7200
8000
4000
4800
5600
6400
7200
8000
4000
4800
5600
6400
7200
8000
A-2-16

Overview of electronic trip units (Standard type)
Types: ETS23, ETS33, ETS43

3 frame size of circuit breaker: 250AF, 630AF, 800AF
Only three(3) pole circuit breakers are available.
The Trip units can be mounted on circuit breakers of N, H and L type from TS100 to TS800.
Test connector for trip unit (AC/DC 30mA ~ AC/DC 100mA)
Protection
Overload protection
Short-circuit protection
Ratings
Trip units
ETS23
40
80
160
250
400
630
800
Applicable to
ETS33
ETS43
TS100 N/H/L
TS160 N/H/L
TS250 N/H/L
TS400 N/H/L
TS630 N/H/L
TS800 N/H/L
160
320
630
Rated
current,
In (A)
Current setting, Ir(A)

ETS
16
32
40
64
80
100
250
400
ETS23 for TS100N/H/L

Setting values
Overload protection (long time)
Setting current (A), Ir
Tripping time (s)
0.4, 0.45, 0.5, 0.55, 0.6, 0.65, 0.7, 0.75, 0.8, 0.85, 0.9, 0.95, 1.0In,
13 setting
Fixed at 6Ir , tolerance20%
Short-circuit protection (short time)

Tripping threshold (A), Isd
Time delay (ms)
adjustable 1.5, 2, 3, 4, 5, 6, 7, 8, 10Ir, 9 setting, tolerance 15%

adjustable 50, 100, 200, 300, 4 setting, tolerance 20%
Short circuit protection (Instantaneous)

Tripping threshold (A), Ii
A-2-17
Fixed at 11In
800

Overview of electronic trip units (Standard type)
Adjustable rated current

setting (Ir)
ETS23 for TS100/TS160/TS250
Adjustable short time

delay current setting (Isd)
Adjustable time delay

setting (tsd)
Alarm LED
90% Ir: ON,
105% Ir or more: ON-OFF
Test connector
ETS33 for TS400/TS630
.7
.6
1.0
.4
alarm
2
1.5
.9
.5
.8
90%
105%
ETS33
10
tr
.3
tsd
tsd
.2
.1
Ir
Isd
Ii
In 630A
.3
.05
TEST
tsd
Ir Isd
Ii
ETS43 for TS800
.6
.7
.8
.4
1.0
alarm
2
1.5
.9
.5
90%
105%
ETS43
10
.3
.2
.1
TEST
.3
.05
tsd
In 800A
A-2-18

Configuration
Electronic type, ETS23 for MCCBs TS100, TS160, TS250
Indication of alarm
Load: not less than 90% Ir LED ON
Load: not less than 105% Ir LED flickering
Trip unit rating, In
Test connector
Short time tripping delay
Short circuit protection (short time)

.6
Ir
.7
.8
.9
.5
tr
Overload protection
(long time)
1.0
.4
td
1.5

(short time)
10
.3
.2
tsd
.1
tsd
.05
.3
Short time tripping

delay

Ir
Isd
Ii
Icu
Tripping time (s)
0.4, 0.45, 0.5, 0.55, 0.6, 0.65, 0.7,

0.75, 0.8, 0.85, 0.9, 0.95, 1.0In
13 settings

Tripping threshold (A),
(Isd)
Time delay
(tsd)
1.5, 2, 3, 4, 5, 6, 7, 8, 10Ir
9 settings, tolerance 15%
setting time (ms)
50
operation time (ms) 30t70
100
200
70t140 140t240
300
240t350
4 settings

Fixed at 11In

ETS
23
In250A
Trip unit frame
- 23 for TS100, TS160, TS250
- 33 for TS400, TS630
- 43 for TS800
Rated current, In
- 40, 80A for TS100
- 40, 80, 160A for TS160
- 40, 80, 160, 250A for TS250
Trip unit function

- ETS: Standard electronic trip unit
A-2-19

Current setting, Ir (A)
Standard electronic trip unit, ETS23
16
32
40
64
80
100
160
250
320
400
40
80
630
800
Trip unit
for TS100
for TS160
for TS250
Setting details
.7
.6
Trip unit rating, In(A)
TS100
40
TS160
80
40
80
TS250
160
160
250
1.0
.4
Circuit breakers
.8
.9
.5
Ir
Setting value
tr
td
Overload protection setting current Ir = Setting value (0.4~1) In
0.4
16
32
16
32
64
16
32
64
100
0.45
18
36
18
36
72
18
36
72
113
0.5
20
40
20
40
80
20
40
80
125
0.55
22
44
22
44
88
22
44
88
138
tsd
tsd
Ir
Isd
Ii
Icu
0.6
24
48
24
48
96
24
48
96
150
0.65
26
52
26
52
104
26
52
104
163
0.7
28
56
28
56
112
28
56
112
175
0.75
30
60
30
60
120
30
60
120
188
0.8
32
64
32
64
128
32
64
128
200
0.85
34
68
34
68
136
34
68
136
213
0.9
36
72
36
72
144
36
72
144
225
0.95
38
76
38
76
152
38
76
152
238
40
80
40
80
160
40
80
160
250
Long time tripping delay, td (sec)

t
Ir
tr
Tripping time (s)

td
Fixed at 6Ir
tolerance20%
tsd
tsd
Ir
Isd
Ii
Icu
A-2-20

Setting details
4
Circuit breakers
2
1.5
t
TS100
40
TS160
80
40
80
TS250
160
40
80
160
250
10
Ir
Setting value
tr
td
0.4
tsd
tsd
Ir
Isd
Ii
Icu
24
48
24
48
96
24
48
96
150
0.45
27
54
27
54
108
27
54
108
169
0.5
30
60
30
60
120
30
60
120
188
0.55
33
66
33
66
132
33
66
132
206
0.6
36
72
36
72
144
36
72
144
225
0.65
39
78
39
78
156
39
78
156
244
42
84
42
84
168
42
84
168
263
0.75
45
90
45
90
180
45
90
180
281
0.8
48
96
48
96
192
48
96
192
300
0.85
51
102
51
102
204
51
102
204
319
0.9
54
108
54
108
216
54
108
216
338
0.95
57
114
57
114
228
57
114
228
356
60
120
60
120
240
60
120
240
375
0.7
1.5
0.4
32
64
32
64
128
32
64
128
200
0.45
36
72
36
72
144
36
72
144
225
0.5
40
80
40
80
160
40
80
160
250
0.55
44
88
44
88
176
44
88
176
275
0.6
48
96
48
96
192
48
96
192
300
0.65
52
104
52
104
208
52
104
208
325
0.7
56
112
56
112
224
56
112
224
350
0.75
60
120
60
120
240
60
120
240
375
400
0.8
64
128
64
128
256
64
128
256
0.85
68
136
68
136
272
68
136
272
425
0.9
72
144
72
144
288
72
144
288
450
0.95
76
152
76
152
304
76
152
304
475
500
80
160
80
160
320
80
160
320
0.4
48
96
48
96
192
48
96
192
300
0.45
54
108
54
108
216
54
108
216
338
0.5
60
120
60
120
240
60
120
240
375
0.55
66
132
66
132
264
66
132
264
413
0.6
72
144
72
144
288
72
144
288
450
0.65
0.7
A-2-21
Short time pick-up current setting, Isd = Setting value (1.5~10)Ir
78
156
78
156
312
78
156
312
488
84
168
84
168
336
84
168
336
525
0.75
90
180
90
180
360
90
180
360
563
0.8
96
192
96
192
384
96
192
384
600
0.85
102
204
102
204
408
102
204
408
638
0.9
108
216
108
216
432
108
216
432
675
0.95
114
228
114
228
456
114
228
456
713
120
240
120
240
480
120
240
480
750

Circuit breakers
2
1.5
t
TS100
40
TS160
80
40
80
TS250
160
40
80
160
250
256
400
10
Ir
Setting value
tr
td
0.4
tsd
tsd
Ir
Isd
Ii
Icu

64
128
64
128
256
64
128
0.45
72
144
72
144
288
72
144
288
450
0.5
80
160
80
160
320
80
160
320
500
0.55
88
176
88
176
352
88
176
352
550
0.6
96
192
96
192
384
96
192
384
600
0.65
0.7
104
208
104
208
416
104
208
416
650
112
224
112
224
448
112
224
448
700
0.75
120
240
120
240
480
120
240
480
750
0.8
128
256
128
256
512
128
256
512
800
0.85
136
272
136
272
544
136
272
544
850
0.9
144
288
144
288
576
144
288
576
900
0.95
152
304
152
304
608
152
304
608
950
160
320
160
320
640
160
320
640
1000
500
0.4
80
160
80
160
320
80
160
320
0.45
90
180
90
180
360
90
180
360
563
0.5
100
200
100
200
400
100
200
400
625
0.55
110
220
110
220
440
110
220
440
688
0.6
120
240
120
240
480
120
240
480
750
0.65
130
260
130
260
520
130
260
520
813
140
280
140
280
560
140
280
560
875
0.75
150
300
150
300
600
150
300
600
938
1000
0.7
0.8
160
320
160
320
640
160
320
640
0.85
170
340
170
340
680
170
340
680
1063
0.9
180
360
180
360
720
180
360
720
1125
0.95
190
380
190
380
760
190
380
760
1188
200
400
200
400
800
200
400
800
1250
0.4
96
192
96
192
384
96
192
384
600
0.45
108
216
108
216
432
108
216
432
675
0.5
120
240
120
240
480
120
240
480
750
0.55
132
264
132
264
528
132
264
528
825
0.6
144
288
144
288
576
144
288
576
900
0.65
0.7
156
312
156
312
624
156
312
624
975
168
336
168
336
672
168
336
672
1050
0.75
180
360
180
360
720
180
360
720
1125
0.8
192
384
192
384
768
192
384
768
1200
0.85
204
408
204
408
816
204
408
816
1275
0.9
216
432
216
432
864
216
432
864
1350
0.95
228
456
228
456
912
228
456
912
1425
240
480
240
480
960
240
480
960
1500
A-2-22

Setting details
4
Circuit breakers
2
1.5
t
TS100
40
TS160
80
40
80
TS250
160
40
80
160
250
448
700
10
Ir
Setting value
tr
td
0.4
tsd
tsd
Ir
Isd
Ii
Icu
224
112
224
448
112
224
0.45
126
252
126
252
504
126
252
504
788
0.5
140
280
140
280
560
140
280
560
875
0.55
154
308
154
308
616
154
308
616
963
0.6
168
336
168
336
672
168
336
672
1050
0.65
0.7
182
364
182
364
728
182
364
728
1138
196
392
196
392
784
196
392
784
1225
0.75
210
420
210
420
840
210
420
840
1313
0.8
224
448
224
448
896
224
448
896
1400
1488
0.85
238
476
238
476
952
238
476
952
0.9
252
504
252
504
1008
252
504
1008
1575
0.95
266
532
266
532
1064
266
532
1064
1663
280
560
280
560
1120
280
560
1120
1750
800
0.4
128
256
128
256
512
128
256
512
0.45
144
288
144
288
576
144
288
576
900
0.5
160
320
160
320
640
160
320
640
1000
0.55
176
352
176
352
704
176
352
704
1100
0.6
192
384
192
384
768
192
384
768
1200
0.65
208
416
208
416
832
208
416
832
1300
224
448
224
448
896
224
448
896
1400
0.75
240
480
240
480
960
240
480
960
1500
0.7
0.8
256
512
256
512
1024
256
512
1024
1600
0.85
272
544
272
544
1088
272
544
1088
1700
0.9
288
576
288
576
1152
288
576
1152
1800
0.95
304
608
304
608
1216
304
608
1216
1900
320
640
320
640
1280
320
640
1280
2000
0.4
160
320
160
320
640
160
320
640
1000
0.45
180
360
180
360
720
180
360
720
1125
0.5
200
400
200
400
800
200
400
800
1250
0.55
220
440
220
440
880
220
440
880
1375
0.6
240
480
240
480
960
240
480
960
1500
0.65
0.7
A-2-23

112
10
260
520
260
520
1040
260
520
1040
1625
280
560
280
560
1120
280
560
1120
1750
1875
0.75
300
600
300
600
1200
300
600
1200
0.8
320
640
320
640
1280
320
640
1280
2000
0.85
340
680
340
680
1360
340
680
1360
2125
0.9
360
720
360
720
1440
360
720
1440
2250
0.95
380
760
380
760
1520
380
760
1520
2375
400
800
400
800
1600
400
800
1600
2500

Setting details
Short time tripping delay setting, tsd (ms)
.3
Time delay
(tsd)
.2
.1
.3
.05
t
Ir
setting time (ms)
50
100
200
300
4 settings
70t140 140t240
240t350
tr
td
tsd
tsd
Ir
Isd
Ii
Icu
Short circuit protection (Instantaneous), Ii (A)

t
Ir

Ii
tr
td
Fixed at 11In
tsd
tsd
Ir
Isd
Ii
Icu
A-2-24

Configuration
Electronic type, ETS33 for MCCBs TS400 & TS630
Indication of alarm

Test connector
.6
Ir
.7
.8
.9
.5
tr
Overload protection
(long time)
1.0
.4
td
1.5

(short time)
10
.3
Short time tripping

delay
.2
tsd
.1
tsd
.05
.3
Ir
Isd
Ii
Icu
Tripping time (s)
0.4, 0.45, 0.5, 0.55, 0.6, 0.65, 0.7,

0.75, 0.8, 0.85, 0.9, 0.95, 1.0In
13 settings

(Isd)
Time delay
(tsd)
1.5, 2, 3, 4, 5, 6, 7, 8, 10Ir
setting time (ms)
50
100
200
70t140 140t240
300
240t350
4 settings

Fixed at 11In

ETS
33
In630A
Trip unit frame
- 23 for TS100, TS160, TS250
- 33 for TS400, TS630
- 43 for TS800
Rated current, In
- 160, 250, 400A for TS400
- 160, 250, 400, 630A for
TS630
Trip unit function

A-2-25

16
32
40
64
80
100
160
250
320
400
630
800
Trip unit
for TS400
for TS630
Setting details
.7
.6
Circuit breakers
160
250
TS630
400
160
250
400
630
1.0
.4
Setting value
Ir
TS400
.8
.9
.5
tr
0.4
64
100
160
64
100
160
252
0.45
72
113
180
72
113
180
284
0.5
80
125
200
80
125
200
315
0.55
88
138
220
88
138
220
347
0.6
96
150
240
96
150
240
378
0.65
104
163
260
104
163
260
410
0.7
112
175
280
112
175
280
441
0.75
120
188
300
120
188
300
473
0.8
128
200
320
128
200
320
504
0.85
136
213
340
136
213
340
536
0.9
144
225
360
144
225
360
567
td
tsd
tsd
Ir
Isd
Ii
Icu
0.95
152
238
380
152
238
380
599
160
250
400
160
250
400
630

t
Ir
tr
Tripping time (s)

td
Fixed at 6Ir
tolerance20%
tsd
tsd
Ir
Isd
Ii
Icu
A-2-26

Setting details
4
Circuit breakers
2
1.5
t
TS400
160
250
TS630
400
160
250
400
630
10
Ir
Short time pick-up current setting, Isd = Setting value (1.5~10) Ir
Setting value
tr
td
tsd
tsd
Ir
Isd
Ii
Icu
0.4
96
150
240
96
150
240
378
0.45
108
169
270
108
169
270
425
0.5
120
188
300
120
188
300
473
0.55
132
206
330
132
206
330
520
0.6
144
225
360
144
225
360
567
156
244
390
156
244
390
614
168
263
420
168
263
420
662
0.75
180
281
450
180
281
450
709
0.8
192
300
480
192
300
480
756
0.85
204
319
510
204
319
510
803
0.9
216
338
540
216
338
540
851
0.95
228
356
570
228
356
570
898
240
375
600
240
375
600
945
504
0.65
0.7
1.5
0.4
128
200
320
128
200
320
0.45
144
225
360
144
225
360
567
0.5
160
250
400
160
250
400
630
0.55
176
275
440
176
275
440
693
0.6
192
300
480
192
300
480
756
0.65
208
325
520
208
325
520
819
224
350
560
224
350
560
882
0.75
240
375
600
240
375
600
945
1008
0.7
0.8
256
400
640
256
400
640
0.85
272
425
680
272
425
680
1071
0.9
288
450
720
288
450
720
1134
0.95
304
475
760
304
475
760
1197
320
500
800
320
500
800
1260
0.4
192
300
480
192
300
480
756
0.45
216
338
540
216
338
540
851
0.5
240
375
600
240
375
600
945
0.55
264
413
660
264
413
660
1040
0.6
288
450
720
288
450
720
1134
0.65
0.7
A-2-27
312
488
780
312
488
780
1229
336
525
840
336
525
840
1323
0.75
360
563
900
360
563
900
1418
0.8
384
600
960
384
600
960
1512
0.85
408
638
1020
408
638
1020
1607
0.9
432
675
1080
432
675
1080
1701
0.95
456
713
1140
456
713
1140
1795
480
750
1200
480
750
1200
1890

Setting details
4
2
1.5
t
Circuit breakers
TS400
160
250
TS630
400
160
250
400
630
10
Ir
Setting value
tr
td
0.4
tsd
tsd
Ir
Isd
Ii
Icu
256
400
640
256
400
640
1008
0.45
288
450
720
288
450
720
1134
0.5
320
500
800
320
500
800
1260
0.55
352
550
880
352
550
880
1386
0.6
384
600
960
384
600
960
1512
1638
0.65
416
650
1040
416
650
1040
448
700
1120
448
700
1120
1764
0.75
480
750
1200
480
750
1200
1890
0.8
512
800
1280
512
800
1280
2016
2142
0.7
0.85
544
850
1360
544
850
1360
0.9
576
900
1440
576
900
1440
2268
0.95
608
950
1520
608
950
1520
2394
640
1000
1600
640
1000
1600
2520
0.4
320
500
800
320
500
800
1260
0.45
360
563
900
360
563
900
1418
0.5
400
625
1000
400
625
1000
1575
0.55
440
687.5
1100
440
688
1100
1733
0.6
480
750
1200
480
750
1200
1890
0.65
520
813
1300
520
813
1300
2048
560
875
1400
560
875
1400
2205
0.75
0.7
600
938
1500
600
938
1500
2363
2520
0.8
640
1000
1600
640
1000
1600
0.85
680
1063
1700
680
1063
1700
2678
0.9
720
1125
1800
720
1125
1800
2835
0.95
760
1188
1900
760
1188
1900
2993
800
1250
2000
800
1250
2000
3150
0.4
384
600
960
384
600
960
1512
0.45
432
675
1080
432
675
1080
1701
0.5
480
750
1200
480
750
1200
1890
2079
0.55
528
825
1320
528
825
1320
0.6
576
900
1440
576
900
1440
2268
0.65
624
975
1560
624
975
1560
2457
672
1050
1680
672
1050
1680
2646
0.7
0.75
720
1125
1800
720
1125
1800
2835
0.8
768
1200
1920
768
1200
1920
3024
0.85
816
1275
2040
816
1275
2040
3213
0.9
864
1350
2160
864
1350
2160
3402
0.95
912
1425
2280
912
1425
2280
3591
960
1500
2400
960
1500
2400
3780
A-2-28

Setting details
4
Circuit breakers
2
1.5
t
TS400
160
250
TS630
400
160
250
400
630
10
Ir
Setting value
tr
td
0.4
tsd
tsd
Ir
Isd
Ii
Icu
448
1120
448
700
1120
1764
1984
0.45
504
788
1260
504
788
1260
0.5
560
875
1400
560
875
1400
2205
0.55
616
963
1540
616
963
1540
2425
0.6
672
1050
1680
672
1050
1680
2646
0.65
0.7
728
1138
1820
728
1138
1820
2867
784
1225
1960
784
1225
1960
3087
0.75
840
1313
2100
840
1313
2100
3308
0.8
896
1400
2240
896
1400
2240
3528
0.85
952
1488
2380
952
1488
2380
3749
0.9
1008
1575
2520
1008
1575
2520
3969
0.95
1064
1663
2660
1064
1663
2660
4190
1120
1750
2800
1120
1750
2800
4410
0.4
512
800
1280
512
800
1280
2016
0.45
576
900
1440
576
900
1440
2268
0.5
640
1000
1600
640
1000
1600
2520
0.55
704
1100
1760
704
1100
1760
2772
0.6
768
1200
1920
768
1200
1920
3024
0.65
832
1300
2080
832
1300
2080
3276
896
1400
2240
896
1400
2240
3528
0.75
960
1500
2400
960
1500
2400
3780
4032
0.7
0.8
1024
1600
2560
1024
1600
2560
0.85
1088
1700
2720
1088
1700
2720
4284
0.9
1152
1800
2880
1152
1800
2880
4536
0.95
1216
1900
3040
1216
1900
3040
4788
1280
2000
3200
1280
2000
3200
5040
0.4
640
1000
1600
640
1000
1600
2520
0.45
720
1125
1800
720
1125
1800
2835
0.5
800
1250
2000
800
1250
2000
3150
0.55
880
1375
2200
880
1375
2200
3465
0.6
960
1500
2400
960
1500
2400
3780
0.65
0.7
A-2-29
700
10
1040
1625
2600
1040
1625
2600
4095
1120
1750
2800
1120
1750
2800
4410
0.75
1200
1875
3000
1200
1875
3000
4725
0.8
1280
2000
3200
1280
2000
3200
5040
0.85
1360
2125
3400
1360
2125
3400
5355
0.9
1440
2250
3600
1440
2250
3600
5670
0.95
1520
2375
3800
1520
2375
3800
5985
1600
2500
4000
1600
2500
4000
6300

Setting details
.3
Time delay
(tsd)
.2
.1
.3
.05
t
Ir
setting time (ms)
50
100
200
300
4 settings
70t140 140t240
240t350
tr
td
tsd
tsd
Ir
Isd
Ii
Icu

t
Ir

Ii
tr
td
Fixed at 11In
tsd
tsd
Ir
Isd
Ii
Icu
A-2-30

ETS43 for MCCBs TS800
Configuration
Electronic type, ETS43 for MCCBs TS800
Indication of alarm

Test connector
.6
Ir
.7
.8
.9
.5
tr
Overload protection
(long time)
1.0
.4
td
1.5

(short time)
10
.3
Short time tripping

delay
.2
tsd
.1
tsd
.05
.3
Ir
Isd
Ii
Icu
Tripping time (s)
0.4, 0.45, 0.5, 0.55, 0.6, 0.65, 0.7,

0.75, 0.8, 0.85, 0.9, 0.95, 1.0In
13 settings

(Isd)
Time delay
(tsd)
1.5, 2, 3, 4, 5, 6, 7, 8, 10Ir
setting time (ms)
50
100
200
70t140 140t240
300
240t350

Fixed at 11In

ETS
43
In800A
Trip unit frame
- 23 for TS100, TS160, TS250
- 33 for TS400, TS630
- 43 for TS800
Rated current, In
- 630, 800A for TS800
Trip unit function

A-2-31
4 settings

16
32
40
64
80
100
160
250
320
400
630
800
Trip unit
for TS800
Setting details
.7
.6
TS800
.9
.5
630
800
1.0
.4
Circuit breakers
.8
Ir
Setting value
tr
0.4
td
252
320
0.45
284
360
0.5
315
400
tsd
tsd
Ir
Isd
Ii
Icu
0.55
347
440
0.6
378
480
0.65
410
520
0.7
441
560
0.75
473
600
0.8
504
640
0.85
536
680
0.9
567
720
0.95
599
760
630
800

t
Ir
tr
Tripping time (s)

td
Fixed at 6Ir
tolerance20%
tsd
tsd
Ir
Isd
Ii
Icu
A-2-32

Setting details
4
Circuit breakers
2
1.5
t
TS800
630
800
10
Ir
Setting value
tr
td
tsd
tsd
Ir
Isd
Ii
Icu
378
0.45
425
540
0.5
473
600
0.55
520
660
0.6
567
720
614
780
0.65
0.7
1.5
480
662
840
0.75
709
900
0.8
756
960
0.85
804
1020
0.9
850.5
1080
0.95
898
1140
945
1200
640
0.4
504
0.45
567
720
0.5
630
800
0.55
693
880
0.6
756
960
0.65
819
1040
0.7
882
1120
0.75
945
1200
0.8
1008
1280
0.85
1071
1360
0.9
1134
1440
0.95
1197
1520
1600
1260
0.4
756
960
0.45
851
1080
0.5
945
1200
0.55
1040
1320
0.6
1134
1440
0.65
1229
1560
1323
1680
0.75
1418
1800
0.8
1512
1920
0.85
1607
2040
0.9
1701
2160
0.7
A-2-33
0.4
0.95
1796
2280
1890
2400

Setting details
4
1.5
Circuit breakers
TS800
630
800
10
Ir
Setting value
tr
td
0.4
tsd
tsd
Ir
Isd
Ii
Icu

1008
1280
0.45
1134
1440
0.5
1260
1600
0.55
1386
1760
0.6
1512
1920
0.65
0.7
1638
2080
1764
2240
0.75
1890
2400
0.8
2016
2560
0.85
2142
2720
0.9
2268
2880
0.95
2394
3040
2520
3200
1600
0.4
1260
0.45
1418
1800
0.5
1575
2000
0.55
1733
2200
0.6
1890
2400
0.65
2048
2600
2205
2800
0.75
2363
3000
3200
0.7
0.8
2520
0.85
2678
3400
0.9
2835
3600
0.95
2993
3800
3150
4000
0.4
1512
1920
0.45
1701
2160
0.5
1890
2400
0.55
2079
2640
0.6
2268
2880
0.65
0.7
2457
3120
2646
3360
0.75
2835
3600
0.8
3024
3840
0.85
3213
4080
0.9
3402
4320
0.95
3591
4560
3780
4800
A-2-34

Setting details
4
2
1.5
t
Circuit breakers
TS800
630
800
10
Ir
Setting value
tr
td
tsd
tsd
Ir
Isd
Ii
Icu
1764
2240
0.45
1985
2520
0.5
2205
2800
0.55
2426
3080
0.6
2646
3360
2867
3640
3087
3920
0.75
3308
4200
0.8
3528
4480
0.85
3749
4760
0.9
3969
5040
0.95
4190
5320
4410
5600
0.65
0.7
0.4
2016
2560
0.45
2268
2880
0.5
2520
3200
0.55
2772
3520
0.6
3024
3840
0.65
3276
4160
3528
4480
0.75
3780
4800
0.7
0.8
4032
5120
0.85
4284
5440
0.9
4536
5760
0.95
4788
6080
5040
6400
0.4
2520
3200
0.45
2835
3600
0.5
3150
4000
0.55
3465
4400
0.6
3780
4800
0.65
4095
5200
4410
5600
0.75
4725
6000
0.8
5040
6400
0.85
5355
6800
0.9
5670
7200
0.7
A-2-35
0.4
10
0.95
5985
7600
6300
8000

Setting details
.3
Time delay
(tsd)
.2
.1
.3
.05
t
Ir
setting time (ms)
50
100
200
300
4 settings
70t140 140t240
240t350
tr
td
tsd
tsd
Ir
Isd
Ii
Icu

t
Ir

Ii
tr
td
Fixed at 11In
tsd
tsd
Ir
Isd
Ii
Icu
A-2-36

Overview
Types : ETM33, ETM43
Range of overload protection setting current (Ir): 64~630A (ETM33), 250~800A (ETM43)
Two frame size of circuit breakers: 630AF, 800AF
Trip units ETM33 and ETM43 can be mounted on circuit breakers of N, H and L type TS400 / TS630 / TS800
Only three(3) pole circuit breakers are available.
Ratings
Rated current, In(A)
Rated current
Trip unit
In (A)
ETM33
ETM43
160
250
400
630
800
Circuit breakers
TS400 N/H/L
TS630 N/H/L
TS800 N/H/L
Current setting, Ir(A)

Trip unit
Overload protection
setting current, Ir(A)
ETM33
ETM33
ETM43
64
80
100
160
250
400
630
800
Applicable circuit breakers
A-2-37
TS400 N/H/L
TS630 N/H/L
TS800 N/H/L

Overview
Setting values
Adjustable 0.4 ~ 1.0In, 30 settings
Tripping time (s) at 6Ir
Adjustable 2, 4, 6, 8,12 5 settings, tolerance20%

Tripping threshold (A), Isd
Adjustable 1.5, 2, 3, 4, 5, 6, 7, 8, 10Ir, 9 settings, tolerance 15%
Time delay
(tsd)
setting time (ms)
50
100
200
300
operation time (ms)
30t70
70t140
140t240
240t350
4 settings
I2t is off
Short-circuit protection (instantaneous)

Adjustable 1.5, 2, 4, 5, 6, 8, 10, 11In, 9 settings
Indication of tripping reason

LED indication
Ir, Isd, Ii, (Ig)
Option for TS400ETM to TS800ETM

Ammeter (A)
Maximum load phase current and R,S,T,N phase current

Adjustable tripping threshold (A), 0.2~1In, 9 setting
Earth fault protection (E)
setting time (ms)
100
200
300
400
operation time (ms) 60t140 140t230 230t350 350t500

Communication (C)
Setting, R, S, T, N phase current, tripping reason
ZSI (Z)
ZSI input and output signal
4 settings
I2t is off
A-2-38

Overview
Adjustable rated current
setting (Ir)
ETM33 for TS400/TS630
Adjustable long time

setting (tr)
Adjustable short time

current setting (Isd)
Adjustable time delay

setting (tsd)
Adjustable instantaneous
current setting (Ii)
Ir = 625A
It = 540A
Adjustable earth fault

current setting (Ig)
Adjustable earth fault
delay setting (tg)
Indication LED
TR (trip reason) button

Display LCD (Ammeter)
Auxiliary power
Test connector
Alarm LED
ETM43 for TS800
tr
Ir = 760A
It = 695A
Isd
ON
ON
tsd
OFF
lg
ta
li
OFF
A-2-39

Configuration
Ir = 625A
It = 540A
Adjustable rated current setting (Ir)
Indication LED
Adjustable long time setting (tr)
Adjustable short time current setting (Isd)
Adjustable time delay setting (tsd)
Battery
Adjustable instantaneous current setting (Ii)
Test connector
Adjustable earth fault current setting (Ig)
Alarm LED
Adjustable earth fault delay setting (tg)
90% Ir : ON,
Alarm indication
90%
105%
alarm
Ir
Isd
Ig
The LED lights and remains lit when the load exceeds 90 % of Ir.
The LED blinks for an overload(105% Ir), warning that the circuit breaker may trip.
Fault indications
LEDs indicate the type of fault that caused tripping:
Ir : overload
Isd : short-circuit ( short time, instantaneous)
Ig : earth fault
If push the TR button to indicate the tripping reason, the indication LED of tripping is ON.
The information is however stored in memory and the LED can be reilluminated by pressing the TR button.
The LED automatically goes off and the memory is cleared when the circuit breaker is reset.
In normal condition, if push TR button, all indication LED is ON for testing auxiliary power and LED.
A-2-40

Tripping characteristics
Trip unit, ETM33
.8
.9
.95
.9
.7
.6
.85
.8
.5
Long time protection against

overloads
Io = Coarse adjustment (function of In)
Ir = Fine adjustment
tr = Long time delay
12
8
6
4
tr
12
tr(6Ir)
4
Isd
2
1.5
ON
ON
.5
.6
.3
.2
2
.3 I t
10
.3
.2
.2
.1
.1
.05
.05
on tsd off
tsd
li
tg
OFF
.4
OFF
lg
.4
.8
.3
1
off
.2
I2t
Instantaneous protection
Ii = Instantaneous threshold
10
1.5
.7

Isd = Short circuit threshold,
tsd = Short circuit time delay
I2t curve in position ON or OFF
11
.4
.3
.2
Earth fault protection

Ig = Insulation fault threshold
tg = Earth fault time delay
.1
.1
on tg off

ETM
33
In600A
Trip unit frame
- 33 for TS400, TS630
- 43 for TS800
Rated current, In
- 160, 250, 400A for TS400
- 160, 250, 400, 630A for TS630
Trip unit function

- ETM : Multifunction electronic trip unit
A-2-41

Setting details
Overload protection setting current, Ir(A)
Trip unit type
ETM33
16
32
40
64
80
100
160
250
320
400
630
800
for TS400
for TS630

.8
.9
Type of trip unit
.7
.6
.5
TS400ETM
160
250
400
Setting
tr
Isd
ON
ON
value
Coarse, Io
Fine, Ir
ta
0.8
64
100
160
0.85
68
106.25
170
0.9
72
112.5
180
0.95
76
118.75
190
200
tsd
OFF
lg
Setting
value
li
OFF
0.5
I
0.6
0.7
0.8
0.9
80
125
0.8
76.8
120
192
0.85
81.6
127.5
204
0.9
86.4
135
216
0.95
91.2
142.5
228
96
150
240
0.8
89.6
140
224
0.85
95.2
148.75
238
0.9
100.8
157.5
252
0.95
106.4
166.25
266
112
175
280
0.8
102.4
160
256
0.85
108.8
170
272
0.9
115.2
180
288
0.95
121.6
190
304
128
200
320
0.8
115.2
180
288
0.85
122.4
191.25
306
0.9
129.6
202.5
324
0.95
136.8
213.75
342
144
225
360
0.8
128
200
320
0.85
136
212.5
340
0.9
144
225
360
0.95
152
237.5
380
160
250
400
A-2-42

Setting details
.8
.9
Type of trip unit
.7
TS630ETM
.6
.5
160
250
400
630
Setting
tr
Isd
Setting
value
value
Coarse, Io
Fine, Ir
Overload protection setting current, Ir (A)
0.8
ON
ON
ta
64
100
160
252
0.85
68
0.9
72
106.25
170
267.75
112.5
180
0.95
283.5
76
118.75
190
299.25
80
125
200
315
tsd
OFF
lg
li
OFF
0.5
I
0.6
0.7
0.8
0.9
0.8
76.8
120
192
302.4
0.85
81.6
127.5
204
321.3
0.9
86.4
135
216
340.2
0.95
91.2
142.5
228
359.1
96
150
240
378
0.8
89.6
140
224
352.8
0.85
95.2
148.75
238
374.85
0.9
100.8
157.5
252
396.9
0.95
106.4
166.25
266
418.95
112
175
280
441
0.8
102.4
160
256
403.2
0.85
108.8
170
272
428.4
0.9
115.2
180
288
453.6
0.95
121.6
190
304
478.8
128
200
320
504
0.8
115.2
180
288
453.6
0.85
122.4
191.25
306
481.95
0.9
129.6
202.5
324
510.3
0.95
136.8
213.75
342
538.65
144
225
360
567
0.8
128
200
320
504
0.85
136
212.5
340
535.5
0.9
144
225
360
567
0.95
152
237.5
380
598.5
160
250
400
630
Setting example : In
Io
Ir
A-2-43
400A
0.5
0.6
0.7
0.8
0.9
0.8
0.85
0.9
0.95

The short circuit threshold, Isd is a multiple of the overload setting, Ir.
Setting example :
400A
0.5
0.6
0.7
0.8
0.9
0.8 0.85
0.9
0.95
1.5
1.5
10
10
The breaker trips when the

current exceeds 2880 A.
Short circuit time delay
2
.3 I t
tsd
0.05...0.3s
0.05...0.3s
.2
.1
.1
.05
tsd
.3
.2
.05
on tsd off
Earth fault protection(E), optional

The ETM trip units measure the vectorial sum of the three phase current and, if present, that of the
neutral conductor.
If the sum of these values exceeds the set current thresholds for a period of time greater than the
time delay, the breaker is tripped.
.5
lg
0.2....1In
lg
.6
0.2....1In
.8
1
off
.3
.2
0.1....0.4s
tg
.7
.4
0.1....0.4s
tg
.4
I2t
.4
.3
.3
.2
.2
.1
.1
on tg off
Ig = insulation fault threshold

tg = earth fault time delay
A-2-44

Ammeter (A), optional
The Ammeter device has an accuracy of 10%.
The highest phase current is displayed in upper line.
In under line, R, S and T phase current is scrolled autom.
Ammeter display limits:
- minimum current 0.3In (one phase)
- maximum current 10In
Zone selective interlocking (ZSI), optional

Zone Selective Interlocking is mainly used in systems with high rated current and
short circuit current values, with safety and service continuity requirements.
This type of discrimination can be achieved with circuit breakers equipped with
specially designed electronic trip units (ETM for TS circuit breakers).
Zone selective interlocking (ZSI) is a system designed
to reduce the stress on electrical distribution components during short-circuit or earth fault
conditions.
to reduce the tripping times (Lower than hundred milliseconds).
to reduce the damage caused by the fault and of interferences to the power supply system;
A number of circuit breakers are interconnected one after another by a pilot-wire.
Power source: DC24V Power is required.
Operation
With ZSI, ETM trip unit detects the fault and then send the signal to upstream circuit breaker
which applies the set time delay and ignore its present short-time and or/ earth fault delay and
clear the fault with no intentional delay.
Without ZSI, ETM trip unit detects the fault and then trips the circuit breaker with intentional
delay
Intentional
delay: 0.2s
Intentional
delay: 0.2s
CB1
Instantaneous
protection
operation
Intentional
delay: 0.1s
CB2
Fault 2
Instantaneous
protection operation
Fault 1
A-2-45
CB3
Zone
Selective Interlocking

Communication(C), optional
Communication interface: RS485 (Modbus-RTU)
The Modbus RS485 system is an open bus on which communicating Modbus devices are
installed. All kinds of PLCs and computers can be connected to the bus.
Transmitted data :
Protection setting values
Highest current of the three phases
Measurement: R, S, T and N phase current
Fault reading: Type of fault (Overload, short-circuit, etc)
The setting of communication address using TR button and LCD display (Ammeter).
Combination of options
A(Ammeter)
E(Earth fault protection)
A+E
A +C(Communication)
A+E+C
Z(Zone selective interlocking)

Z+A
Z+E
Z+A+E
Z+A +C
Z+A+E+C
A-2-46

Menu structure of the electronic trip unit (ETM)
I r - 1 26 0A
I s - 1 26 5A
A-2-47
Display current value (RMS) of phase which is carrying maximum in

each phase
Display current value (RMS) of each phase at an interval of every 2
seconds.

Feature of trip unit according to option
ETM33 A+E
ETM33 A+E+C
ETM33 Z+A+E
ETM33 Z+A+E+C
ETM33 A
ETM33 A+C
ETM33 Z+A
ETM33 Z+A+C
ETM33 E
ETM33 Z+E
ETM33
ETM33 Z
A-2-48

ETM43 for TS800
Configuration
Ir = 760A
It = 695A
Adjustable rated current setting (Ir)
Adjustable long time setting (tr)
Battery
Adjustable short time current setting (Isd)
Test connector
Adjustable time delay setting (tsd)
Alarm LED 90% Ir : ON,
Adjustable instantaneous current setting (Ii)
Adjustable earth fault current setting (Ig)

Adjustable earth fault delay setting (tg)
Indication LED
90%
105%
alarm
Ir
Isd
Ig
A-2-49
Alarm indication
The LED lights and remains lit when the load exceeds 90 % of Ir.
The LED blinks for an overload(105% Ir), warning that the circuit breaker may trip.
Fault indications
LEDs indicate the type of fault that caused tripping:
Ir : overload
Isd : short-circuit (short time, instantaneous)
Ig : earth fault
The information is however stored in memory and the LED can be reilluminated by pressing the TR button.
The LED automatically goes off and the memory is cleared when the circuit breaker is reset.
In normal condition, if push TR button, all indication LED is ON for testing auxiliary power and LED.

ETM43 for TS800
Tripping characteristics
Trip unit for TS800 circuit breaker
.8
.9
.95
Long time protection against

overloads
Io = Coarse adjustment (function of In)
Ir = Fine adjustment
tr = Long time delay
.9
.7
.6
.85
.8
.5
t
12
8
6

Isd = Short circuit threshold,
tsd = Short circuit time delay
tr
12
tr(6Ir)
4
Isd
7
8
2
.3 I t
10
.2
.1
.1
.05
.05
on tsd off
tsd
li
tg
OFF
.5
.6
.4
.7
I2t
10
1.5
Instantaneous protection
Ii = Instantaneous threshold
11
.4
.4
.8
.3
.3
.3
1
off
.2
.2
.2
.3
.2
OFF
lg
ON
2
1.5
ON
Earth fault protection

Ig = Insulation fault threshold
tg = Earth fault time delay
.1
.1
on tg off

ETM
43
In800A
Trip unit frame
- 33 for TS400, TS630
- 43 for TS800
Rated current, In
- 630, 800A for TS630
Trip unit function

- ETM: Multi function electronic trip unit
A-2-50

ETM43 for TS800
Setting details
Trip unit type
ETM43
16
32
40
64
80
100
160
250
320
400
for TS800

.8
.9
Type of trip unit
.7
.6
.5
TS800ETM
630
800
Setting
tr
Isd
ON
ON
value
Coarse, Io
Fine, Ir
ta
Overload protection setting current, Ir (A)
0.8
252
320
0.85
267.75
340
0.9
283.5
360
0.95
299.25
380
tsd
OFF
lg
Setting
value
li
OFF
0.5
I
0.6
0.7
0.8
0.9
A-2-51
315
400
0.8
302.4
384
0.85
321.3
408
0.9
340.2
432
0.95
359.1
456
378
480
0.8
352.8
448
0.85
374.85
476
0.9
396.9
504
0.95
418.95
532
441
560
0.8
403.2
512
0.85
428.4
544
0.9
453.6
576
0.95
478.8
608
504
640
0.8
453.6
576
0.85
481.95
612
0.9
510.3
648
0.95
538.65
684
567
720
0.8
504
640
0.85
535.5
680
0.9
567
720
0.95
598.5
760
630
800
630
800

ETM43 for TS800
The short circuit threshold, Isd is a multiple of the overload setting, Ir.
Setting example :
800A
0.5
0.6
0.7
0.8
0.9
0.8 0.85
0.9
0.95
1.5
1.5
10
10
The breaker trips when the

current exceeds 2880 A.
Short circuit time delay
2
.3 I t
tsd
0.05...0.3s
0.05...0.3s
.2
.1
.1
.05
tsd
.3
.2
.05
on tsd off
Earth fault protection(E), optional

The ETM trip units measure the vectorial sum of the three phase current and, if present, that of the
neutral conductor.
If the sum of these values exceeds the set current thresholds for a period of time greater than the
time delay, the breaker is tripped.
.5
lg
0.2....1In
lg
.6
0.2....1In
.8
1
off
.3
.2
0.1....0.4s
tg
.7
.4
0.1....0.4s
tg
.4
I2t
.4
.3
.3
.2
.2
.1
.1
on tg off
Ig = insulation fault threshold

tg = earth fault time delay
A-2-52

ETM43 for TS800
Ammeter (A), optional
The Ammeter device has an accuracy of 10%.
The highest phase current is displayed in upper line.
In under line, R, S and T phase current is scrolled autom.
Ammeter display limits:
- minimum current 0.3In (one phase)
- maximum current 10In
Zone selective interlocking (ZSI), optional

Zone Selective Interlocking is mainly used in systems with high rated current and
short circuit current values, with safety and service continuity requirements.
This type of discrimination can be achieved with circuit breakers equipped with
specially designed electronic trip units (ETM for TS circuit breakers).
Zone selective interlocking (ZSI) is a system designed
to reduce the stress on electrical distribution components during short-circuit or earth fault
conditions.
to reduce the tripping times (Lower than hundred milliseconds).
to reduce the damage caused by the fault and of interferences to the power supply system;
A number of circuit breakers are interconnected one after another by a pilot-wire.
Operation
With ZSI, ETM trip unit detects the fault and then send the signal to upstream circuit breaker
which applies the set time delay and ignore its present short-time and or/ earth fault delay and
clear the fault with no intentional delay.
Without ZSI, ETM trip unit detects the fault and then trips the circuit breaker with intentional
delay
Intentional
delay: 0.2s
Intentional
delay: 0.2s
CB1
Instantaneous
protection
operation
Intentional
delay: 0.1s
CB2
Fault 2
Instantaneous
protection operation
Fault 1
A-2-53
CB3
Zone
Selective Interlocking

ETM43 for TS800
Communication(C), optional
Communication interface: RS485 (Modbus-RTU)
The Modbus RS485 system is an open bus on which communicating Modbus devices are
installed. All kinds of PLCs and computers can be connected to the bus.
Transmitted data:
Protection setting values
Highest current of the three phases
Measurement: R, S, T and N phase current
Fault reading: Type of fault (Overload, short-circuit, etc)
The setting of communication address using TR button and LCD display (Ammeter).
Combination of options
A(Ammeter)
E(Earth fault protection)
A+E
A +C(Communication)
A+E+C
Z(Zone selective interlocking)

Z+A
Z+E
Z+A+E
Z+A +C
Z+A+E+C
A-2-54

ETM43 for TS800
Menu structure of the electronic trip unit (ETM)
I r - 1 26 0A
I s - 1 26 5A
A-2-55
Display current value (RMS) of phase which is carrying maximum in

each phase
Display current value (RMS) of each phase at an interval of every 2
seconds.

ETM43 for TS800
Feature of trip unit according to option
ETM43 A+E
ETM43 A+E+C
ETM43 Z+A+E
ETM43 Z+A+E+C
ETM43 A
ETM43 A+C
ETM43 Z+A
ETM43 Z+A+C
ETM43 E
ETM43 Z+E
ETM43
ETM43 Z
A-2-56

TS100
Frame size
[A]
TS250
250
100
160
1.6, 3.2, 6.3, 12, 20,
32, 50, 63,
32, 50, 63, 100
100, 160
[AF]
Rated current, In
TS160
No. of poles
100, 160, 220
Rated operational
AC
[V]
690
690
690
voltage, Ue
DC
[V]
500
500
500
Rated impulse withstand voltage, Uimp

[kV]
[V]
750
750
750
[kA]
100
120
200
100
120
200
100
120
200
380/415V
[kA]
50
85
150
50
85
150
50
85
150
440/460V
[kA]
50
70
130
50
70
130
50
70
130
480/500V
[kA]
42
65
85
42
65
85
42
65
85
660/690V
[kA]
10
15
20
10
15
20
10
15
20
100%
100%
100%
100%
100%
100%
100%
100%
100%
Rated ultimate short-circuit breaking capacity, Icu

AC 50/60Hz
220/240V
Rated service breaking capacity, Ics [%Icu]

Rated short-circuit making capacity, Icm
AC 50/60Hz
220/240V
[kA]
220
264
440
220
264
440
220
264
440
380/415V
[kA]
105
187
330
105
187
330
105
187
330
440/460V
[kA]
105
154
286
105
154
286
105
154
286
480/500V
[kA]
88
143
187
88
143
187
88
143
187
660/690V
[kA]
17
30
40
17
30
40
17
30
40
Category of utilization
Isolation behavior
Trip unit (release)
front-connection
rear-connection
front-connection
magnetic only
Connection
fixed
plug-in
MTU
Mechanical life
[operations]
25000
25000
25000
Electrical life @415 V AC
[operations]
10000
10000
10000
10516086
10516086
10516086
IEC60947-2
IEC60947-2
IEC60947-2
rear-connection
Basic dimensions, WHD
3-pole
[mm]
3-pole
[kg]
(front connection)
Weight
(front connection)
Reference standard
A-2-57
TS400
TS630
TS800
400
630
800
320
500
630
690
690
690
500
500
500
750
750
750
100
120
200
100
120
200
100
120
200
65
85
150
65
85
150
65
100
150
65
85
130
65
85
130
65
100
130
42
65
85
42
65
85
42
85
100
10
20
35
10
20
35
10
20
35
100%
100%
100%
100%
100%
100%
100%
100%
100%
220
264
440
220
264
440
220
264
440
143
187
330
143
187
330
143
220
330
143
187
286
143
187
286
143
220
286
88
143
187
88
143
187
88
187
220
17
40
74
17
40
74
17
40
74
20000
20000
10000
6000
6000
3000
140260110
140260110
210320135
5.4
5.4
15.1
IEC60947-2
IEC60947-2
IEC60947-2
A-2-58

MTU for TS100, TS160, TS250, TS400, TS630, TS800
For the protection of motors from 1.6 to 250kW(400V),
TS100 to TS800 circuit Breakers must be equipped with
a special trip unit MTU adjustable thresholds.
L1
L2
L3
This assembly ensures: Short-circuit protection

(magnetic trip unit with adjustable thresholds); Suitability
for isolation. For the TS100 to TS800 circuit breakers,
trip unit MTU is interchangeable.
Breaker
Contactor
The circuit breakers presented here: Provide protection

against short-circuits; Are suitable for isolation as
defined by IEC60947-2 standard.
O/L
T1
T2
T3
M
Magnetic only
release
Motor
Configuration

and reference temperature
Magnetic setting for short-circuit

protection

TS250
MTU
Magnetic only release
MCCB frame type
- TS100: TS100N, TS100H, TS100L
- TS160: TS160N, TS160H, TS160L
- TS250: TS250N, TS250H, TS250L
- TS400: TS400N, TS400H, TS400L
- TS630: TS630N, TS630H, TS630L
- TS800: TS800N, TS800H, TS800L
A-2-59

MTU for TS100, TS160, TS250, TS400, TS630, TS800
Characteristics
Magnetic trip units(MTU)
Rating(A)
In
TS100 to TS800
1.6
3.2
6.3
12
20
32
50
63
100
160
220
320
500
TS160
TS250
TS400
TS630
TS800
N / H / L TS100
630

Pick - up
Im
setting
6..12In (6 Point)
Setting details
MTU In
6In
..
..
..
..
12In
MTU In
6In
..
..
..
..
12In
1.6
3.2
6.3
12
20
32
50
63
10
20
40
70
120
190
300
400
12
24
48
84
144
228
360
480
14
28
56
98
168
266
420
560
16
32
64
112
192
304
480
640
18
36
72
126
216
342
540
720
20
40
80
140
240
380
600
800
100
160
220
320
500
630
600
960
1320
1920
3000
3780
720
1152
1584
2304
3600
4536
840
1344
1848
2688
4200
5292
960
1536
2112
3072
4800
6048
1080
1728
2376
3456
5400
6804
1200
1920
2640
3840
6000
7560
TS100 MTU
- Adjustable magnetic only unit
MTU
560
480
400
640
720
800
Im
63A
3P
TS160 MTU
MTU
1344
1152
960
1536
1728
1920
Im
160A
3P
TS250 MTU
MTU
1848
1584
1320
2112
2376
2640
Im
220A
Im = 6...12In
3P
14
12
TS400 MTU, TS630 MTU, TS800 MTU

MTU
4600
3800
3000
Im
5400
6200
10
16
18
20
500A
7000
Im
A-2-60
TD series
Frame size
Conventional thermal current, Ith
TD160NA
TS100NA
TS160NA
[AF]
160
100
160
[A]
160
100
160
2, 3, 4
2, 3, 4
2, 3, 4
690
690
No. of poles
Rated operational voltage,
AC
[V]
690
Ue
DC
[V]
500
500
500
160
100
160
Rated operational current, Ie

Rated impulse withstand voltage,Uimp
[kV]
[V]
750
750
750
3.1
2.8
3.6
Rated short-time
1s
[A rms]
2200
2000
2500
withstand current, Icw
3s
[A rms]
2200
2000
2500
[A rms]
960
690
960
front-connection
rear-connection
front-connection
rear-connection
25000
25000
25000
Rated short-circuit making capacity, Icm
[kA peak]
20s
Isolation behavior
Trip unit (release)
disconnector unit
Connection
fixed
plug-in
DSU
Mechanical life
[operations]
Electrical life @415 V AC
[operations]
10000
10000
10000
Basic dimensions, WHD 3-pole
[mm]
9014086
10516086
10516086
(front connection)
[mm]
12014086
14016086
14016086
1.5
4-pole
Weight
3-pole
[kg]
(front connection)
4-pole
[kg]
Reference standard
1.8
2.6
2.6
IEC60947-3
IEC60947-3
IEC60947-3
The switch-disconnectors are different from the circuit-breakers in the absence of the
conventional protection unit. They keep the overall dimensions, connection systems
and accessories unchanged from the corresponding circuit-breakers. Installation
standards require upstream protection. However, thanks to their high-set magnetic
release, TD160 ... TS800 DSU are self protected.
A-2-61
TS series
TS250NA
TS400NA
TS630NA
TS800NA
250
400
630
800
250
400
630
800
2, 3, 4
2, 3, 4
2, 3, 4
2, 3, 4
690
690
690
690
500
500
500
500
250
400
630
800
750
750
750
750
4.9
7.1
8.5
12
3500
5000
6300
8000
3500
5000
6300
8000
1350
1930
2320
2560
25000
20000
20000
10000
10000
6000
6000
3000
10516086
140260110
140260110
210320135
14016086
186.5260110
186.5260110
280320135
5.4
5.4
15.1
2.6
7.2
7.2
19.6
IEC60947-3
IEC60947-3
IEC60947-3
IEC60947-3
A-2-62
Susol MCCB for DC Application
Susol MCCB is sutable for DC application such as

Photovoltaic Circuit Breaker, UPS and datacenter
DC short circuit test tested by VDE
Higher nominal voltage range up to 1000 VDC
Rated Current : 16A~800A
No of Pole: 2/3/4Pole
Available for AC/DC application
Frame size
(AF)
TD100
TD160
TS100
TS160
TS250
TS400
TS630
TS800
100
160
100
160
250
400
630
800
300, 400
500, 630
700, 800
16, 20, 25,

32, 40, 50,
100, 125, 160
40, 50, 63,

80, 100
63, 80, 100

No. of Poles
Rating (DC)
(Pole)
100, 125, 160
125, 160
200, 250
2, 3, 4
2, 3, 4
2, 3, 4
2, 3, 4
2, 3, 4
2, 3, 4
2, 3, 4
2, 3, 4
1000V
4P
4P
4P
4P
4P
4P
4P
4P
750V
3P
3P
3P
3P
3P
3P
3P
3P
500V
2P
2P
L
2P
L
2P
L
2P
L
2P
L
2P
L
2P
Rated service
Type
breaking
1000V (4P)
42
65 100 42
65 100 50 85 100 50 85 100 50 85 100 50 85 100 50 85 100 50 85 100
(DC)
750V (3P)
42
65 100 42
65 100 50 85 100 50 85 100 50 85 100 50 85 100 50 85 100 50 85 100
500V (2P)
42
65 100 42
65 100 50 85 100 50 85 100 50 85 100 50 85 100 50 85 100 50 85 100
Trip unit
FTU (fixed-thermal,
fixed-magnetic)
FMU (adjustable-thermal,
fixed-magnetic)
ATU (adjustable-thermal,
adjustable-magnetic)
Exemplary circuit diagrams
Load
Load
DC500V (2P)
A-2-63
DC750V (3P)
Load
DC1000V (4P)
Load
4 pole MCCB with electronic trip unit
Products application & Function

N-R-S-T and R-S-T-N Type for consideration
of application field
Full line up with 100~800AF
4P4D for N phase protection type
Max. breaking capacity 150kA@415V
KEMA type test and CE certification
Designation
TS100, TS160, TS250
TS400, TS630
TS800
N/H/L
N/H/L
N/H/L
Type
Rated current
40, 80, 100, 160, 250A
160, 250, 400, 630A
630, 800A
Poles
4 (N-R-S-T, R-S-T-N)
AC750V
AC750V
AC750V
8kV
8kV
8kV
Insulation voltage, Ui
Impulse withstand voltage, Uimp
Short-circuit breaking capacity, Icu
AC 50/60Hz
220/240V
100
120
200
100
120
200
100
120
200
380/415V
50
85
150
50
85
150
50
85
150
440/460V
50
70
130
50
70
130
50
70
130
480/500V
42
65
85
42
65
85
42
65
85
660/690V
10
15
20
10
15
20
10
15
20
Ics
Reverse connection (Line/Load)
Tripping device
100% Icu
100% Icu
100% Icu
Available
Available
Available
Electronics
Electronics
Electronics
ETS
Thermal
Io, Ir
Instant.
Neutral protection
ETS: Ir = 0.4~1.0 In (13settings)
ETS & ETM
ETS & ETM
ETM: Io = 0.5~1.0 In (6settings)
ETM: Io = 0.5~1.0 In (6settings)
Ir = 0.8~1.0 Io (5settings)
Ir = 0.8~1.0 Io (5settings)
ETS: 6sec at 6Ir (fixed)
ETM: 12sec at 6Ir (5settings)
ETM: 12sec at 6Ir (5settings)
ETS: 1.5~10 Ir (9settings)
ETS, ETM: 1.5~10 Ir (9settings)
ETS,ETM: 1.5~10 Ir (9settings)
12 In
12 In
12 In
4P3d
No protection
No protection
No protection
4P3d+N/2
0.5 Ir
0.5 Ir
0.5 Ir
tr (6Ir)
Im
It
4P4d
1.0 Ir
1.0 Ir
1.0 Ir
Min
10mm2 or 8 AWG(40A)
70mm2(160A)
185mm2 2 / 350 kcmil 2(630A)
Max
120mm2 or 250kcmil(250A)
185mm2 2 / 350 kcmil 2(630A)
240mm2 2(800A)
Tighetning Torque
Hex.Socket bolt (M8): 6N.m
Hex.Socket bolt (M10): 10N.m
Hex. Socket bolt (M12): 14N.m
MCCB (W H D)
140 160 86
186.5 260 110
280 320 135
Cable
A-2-64

TS1000
TS1250
TS1600
Ampere frame
1000
1250
1600
Pole
3, 4
3, 4
3, 4
1250
1600
Type
TS1000
Rated current,(A)
Rated insulation voltage, (V)
In
-5~40C
800, 1000
Rated impulse withstand voltage, (kV)
Uimp
Ue
TS1600
50C
800, 1000
1250
1560
65C
800, 1000
1250 *
1420
1000
1000
Ui
Rated operational voltage, (V)
TS1250
1000
AC50/60Hz
690
690
690
DC
Rated short-circuit breaking capacity
IEC60947-2
Rated ultimate short-circuit
220/240V
55
75
200
55
75
55
75
AC50/60Hz
breaking capacity, (kA) (Icu)
380/415V
50
70
150
50
70
50
70
440/460V
50
65
130
50
65
50
65
480/500V
40
50
100
40
50
40
50
660/690V
35
45
35
45
35
45
250V 2P
500V 2P
750V 3P
100%
75%
100%
100%
75%
100%
75%
(sym)
DC
Rated service
%Icu
breaking capacity (Ics)

Rated short-circuit
AC50/60Hz 1s
making capacity (kA) (Icw)

Overriding instantaneous protection
25
3s
kA peak
12
-
50
30
25
25
50
50
Isolation
Category
10000
4000
10000
10000
In/2
6000
4000
5000
5000
In
5000
3000
4000
2000
In/2
4000
3000
3000
2000
In
2000
2000
2000
1000
Mechanical life (operations)

(Life cycle)
Electrical life
440V
(operations)
690V
Pollution degree
Dimension (mm)
3
3-pole
327 210 152.5
(H W D)
4-pole
327 280 152.5
Weight (kg)
3-pole
13
4-pole
16.8
Note) *1250A at 65C is supported only with vertical connection.
A-2-65

Overview
Classification
N type
A type
P type
S type
Externals
Current
protection
Other
protection
L / S / I / G / Thermal
L / S / I / G / Thermal
ZSI(Protective coordination)
Earth leakage (Option)
Current (R / S / T / N)
Measurement
function
Fine adjustment
Pre Trip Alarm
Digital Output
3DO (Fixed)
L, S/I, G Alarm
IDMTL setting
Communication
Power supply
RTC timer
LED for
trip info.
Fault recording
Self Power
-Power source
works over 25% of
current of In (one pole)
Available
Long time delay
Short time delay/Instantaneous
Ground fault
-
Event recording
Operating
Reset button button
L / S / I / G / Thermal(Continuous)
ZSI(Protective coordination)
Earth leakage(Option)
Over/Under current
Over/Under frequency
Unbalance(Voltage/Current)
Reverse power
3 Phase Voltage/Current
RMS/Vector
Power(P, Q, S), PF(3-Phase)
Energy(Positive/Negative)
Frequency, Demand
Fine adjustment for long/short

time delay/instantaneous/ ground
Overload protection relays
: DO (Alarm)
(Ground fault is not available
when using Pre trip alarm)
3DO (Programmable)
Trip, Alarm, General
Compliance with IEC60255-3
SIT, VIT, EIT, DT
Modbus / RS-485
Profibus-DP
AC/DC 100~250V
DC 24~60V
Modbus/RS-485
Profibus-DP
Self Power
- Power source works over
25% of current of In (one pole)
- External power source are
required for comm.
AC/DC 100~250V
DC 24~60V
Available
Available
N type
N type
10 records
(Fault/Current/Date and Time)
Reset, Menu
Up/Down, Left/Right, Enter
P type
P type
3 Phase Voltage/Current
RMS/Vector
Power(P, Q, S), PF(3-Phase)
Energy(Positive/Negative)
Frequency, Demand
Voltage/Current harmonics
(1st~63th)
3 Phase Waveforms
THD, TDD, K-Factor
P type
P type
P type
P type
Modbus / RS-485
Profibus-DP
AC/DC 100~250V
DC 24~60V
Basic protection function(L / S / I / G)

is still under normal operation
without control power.
256 records
(Fault/Current/Date and Time)
256 records(Content, Status, Date)
A type
Available
N type
256 records
Last fault wave recording (3 Phase)
P type
A type
A-2-66

type
N type:Normal
Optimized protection function
OCR, OCGR function according IEC60947-2
Overload protection
-Long-time delay
-Thermal
-Short-time delay / Instantaneous
-I2t On/Off optional (for short-time delay)
Ground fault protection
-I2t On/Off optional
Self-Power
LED: Indication of trip info. and overload state
Alarm SP
Ir
Isd
Ii
Ig
Ig: LED indicating ground-fault

Isd/Ii: LED indicating short-time or instantaneous tripping
Ir: LED indicating long-time delay
SP: Self-protection and battery test LED
Alarm: LED indicating an overload
(Turn on above 90%, Blink above 105%)
Reset Key: Fault reset or battery check

Iu, Ir: Long-time current setting, tr: Long-time tripping delay setting
Isd: Short-time current setting, tsd: Short-time tripping delay setting
Ii: Instantaneous current setting
Ig: Ground fault current setting, tg: Ground fault tripping delay setting
Test terminal: OCR test terminal (Connected with OCR tester)
A-2-67

Protection
Long time
Current setting (A)
t
Ir
tr
lsd
tsd
Ii
I
Time delay (s)

Accuracy: 15% or below
100ms
Short time
Current setting (A)
Accuracy: 10%
Time delay (s)
@ 10Ir
Iu = In...
Ir = Iu...
tr@(1.5lr)
tr@(6.0lr)
tr@(7.2lr)
Isd = Ir...
Ig
tsd
Time delay (s)

@ 1In
I
0.7
0.85
50
2
1.38
0.8
0.88
100
4
2.7
0.9
0.9
200
8
5.5
1.0
0.93
300
12
8.3
0.95
400
16
11
0.98
500
20
13.8
1.0
Off
Off
Off
1.5
10
Off
0.2
0.2
0.3
0.3
0.4
0.4
160
260
360
240
340
440
I t Off
0.05 0.1
I2t On
0.1
Min. Trip
20
80
Time(ms)
Max. Trip
80
140
Time(ms)
Ii = In...
2
3
4
50(10ms)
10
12
15
Off
Ig = In...
0.2
0.7
0.8
1.0
Off
tg
tg
0.6
0.83
25
1
0.69
(I2t Off)
Instantaneous
Current setting (A)
Tripping time
Ground fault
Pick-up (A)
Accuracy: 10%(Ig0.4In)
20%(Ig0.4In)
0.5
0.8
12.5
0.5
0.34
(I2t Off)
0.3
0.4
0.5
0.6
0.05 0.1
I2t Off
I2t On
0.1
Min. Trip
20
80
Time(ms)
Max. Trip
80
140
Time(ms)
0.2
0.2
0.3
0.3
0.4
0.4
160
260
360
240
340
440
NV type (For ship only)

Protection
Long time
Current setting (A)
Time delay (s)
100ms
Short time
Current setting (A)
Accuracy: 10%
Time delay (s)
@ 10Ir
Ir = In...
tr@(1.2Ir)
tr@(3Ir)
tr@(6Ir)
0.8
10
0.99
0.24
0.9
15
1.49
0.36
1.0
20
1.99
0.48
1.05
25
2.48
0.59
1.1
30
2.98
0.71
1.15
40
3.97
0.95
1.2
50
4.97
1.19
1.25
60
5.96
1.43
Off
100
9.93
2.38
Isd = In...
2.5
2.7
3.5
4.5
Off
I t Off
0.05 0.1
I2t On
0.1
Min. Trip
20
80
Time(ms)
Max. Trip
80
140
Time(ms)
0.2
0.2
0.3
0.3
0.4
0.4
160
260
360
240
340
440
10
12
14
16
Off
tsd
(I2t Off)
Instantaneous
Current setting (A)
Tripping time
Ii = In...
2
4
6
50(10ms)
The fine-adjustable setting of the rated current[In]

- In = Ict[0.4~1.0]
- Setting range: 40~100% of Ict (unit: 0.5%)
A-2-68

type
A type:Ammeter
Fault recording
-Records Max. up to 10 fault information about fault type,
fault phase, fault data, occurrence time of fault
SBO (Select Before Operation)
-High reliability for control and setting change method
3 DO(Digital Output)
-Fixed
Communication
-Modbus/RS485
-Profibus-DP
Overload protection
-Long-time delay
-Thermal
Realization of protective coordination by ZSI
(Zone Selective Interlocking)
High-performance and high-speed MCU built-in
-Accurate measurement with tolerance of 1.0%
LCD: Indication of measurement and information

Alarm SP
Ir
Isd
Ii
Ig
Comm

Key: Move to menu or reset
Reset
Esc
Reset/ESC: Fault reset or ESC from menu

Enter: Enter into secondary menu or setting input
Up/Down: Move the cursor up/down on screen or
increase/decrease a setting value
Right/Left: Move the cursor or setting right/left on screen
(Rotation)
Menu: Menu display Measurement display
Iu, Ir: Long-time current setting, tr: Long-time tripping delay setting
A-2-69

Protection
Long time
Current setting (A)
Ir
tr
lsd
tsd
Ii
I
Iu = In...
0.5
0.6
Ir = Iu...
0.8
0.83 0.85 0.88 0.9
0.7
0.8
0.9
Time delay (s)
tr@(1.5lr)
12.5 25
50
100
tr@(6.0lr)
0.5
100ms
tr@(7.2lr)
Isd = Ir...
1.0
0.93 0.95 0.98
1.0
200
300
400
500
Off
12
16
20
Off
0.34 0.69 1.38 2.7
5.5
8.3
11
13.8
Off
1.5
10
Off
Short time
Current setting (A)
Accuracy: 10%
Time delay (s)
@ 10Ir
tsd
I2t Off
0.05 0.1
0.2
0.3
0.4
I2t On
0.1
0.2
0.3
0.4
20
80
160
260
360
80
140
240
340
440
10
12
15
Off
0.4
0.5
0.6
0.7
0.8
1.0
Off
10
20
30
Off
Min. Trip
(I2t Off)
Time(ms)
Max. Trip
Time(ms)
Instantaneous
Current setting (A)
Ii = In...
Tripping time
50(10ms)
Ground fault
Pick-up (A)
Ig = In...
0.2
0.3
20%(Ig0.4In)
Ig
tg
tg
Time delay (s)

@ 1In
I2t Off
0.05 0.1
0.2
0.3
0.4
I2t On
0.1
0.2
0.3
0.4
20
80
160
260
360
80
140
240
340
440
0.5
140
230
350
800
950
140
230
350
800
Min. Trip
(I2t Off)
Time(ms)
Max. Trip
Time(ms)
Current setting (A)

I n
In
Time delay (ms)
Alarm
Accuracy: 15%
Time(ms)
Trip
Time(ms)
Note) Earth leakage function is available with ZCT or external CT
A-2-70

type
P type:Power meter
Overload protection
-Long-time delay
-Thermal
Protection for Over voltage/Under voltage/Over
frequency/Under frequency/Unbalance/Reverse power
The fine-adjustable setting by knob and Key
IDMTL setting (SIT, VIT, EIT, DT curve)
- Basic setting : None. Thermal curve.
Measurement and Display Function

-High detailed measurement for 3 phase
current/Voltage/Power/Energy/Phase
angle/Frequency/PF/Demand
-128 x 128 Graphic LCD
-Indicates current/voltage Vector Diagram and Waveform
Fault recording
-Records Max. up to 256 fault information about fault
type, fault phase, fault value, occurrence time of fault
Event recording
-Records events of device related to setting change,
operation and state change. (Max. up to 256)
3 DO(Digital output)
-Programmable for alarm, trip and general DO
Communication
-Modbus/RS485
-Profibus-DP
Graphic LCD: Indication of measurement and information

Alarm SP
Ir
Isd
Ii
Ig
Comm
Comm: LED indicating comm. state (Blink when running)

Reset
Esc

(Rotation)
Ir: Long-time current setting, tr: Long-time tripping delay setting

A-2-71

Protection
t
Ir
tr
lsd
tsd
Ii
I
Long time
Current setting (A)
Time delay (s)
100ms
Short time
Current setting (A)
Accuracy: 10%
Time delay (s)
@ 10Ir
Ir = In...
tr@(1.5lr)
tr@(6.0lr)
tr@(7.2lr)
0.4
12.5
0.5
0.34
0.5
25
1
0.69
0.6
50
2
1.38
0.7
100
4
2.7
0.8
200
8
5.5
0.9
300
12
8.3
1.0
400
16
11
500
20
13.8
Off
Off
Off
Isd = Ir...
1.5
10
Off
0.2
0.2
0.3
0.3
0.4
0.4
80
160
260
360
140
240
340
440
tsd
(I2t Off)
Instantaneous
Current setting (A)
Tripping time
Ground fault
Pick-up (A)
20%(Ig0.4In)
Ig
Time delay (s)

@ 1In

Current setting (A)
Time delay (ms)
Accuracy: 15%
I n
0.05 0.1
0.1
20
Time(ms)
Max. Trip
80
Time(ms)
Ii = In...
2
3
4
50(10ms)
10
12
15
Off
Ig = In...
0.2
0.7
0.8
1.0
Off
10
20
30
Off
tg
tg
I2t Off
I2t On
Min. Trip
(I2t Off)
I2t Off
I2t On
Min. Trip
0.3
0.4
0.5
0.6
0.05 0.1
0.1
0.2
0.2
0.3
0.3
0.4
0.4
80
160
260
360
140
240
340
440
230
350
800
950
230
350
800
20
Time(ms)
Max. Trip
80
Time(ms)
In
0.5
Alarm
140
Time(ms)
Trip
140
Time(ms)

I
PTA(Pre Trip Alarm)

Current setting (A)
Time delay (s)
Accuracy: 15%
Other protection
Under voltage
Over voltage
Voltage unbalance
Reverse power
Over power
Current unbalance
Over
60Hz
frequency
50Hz
Under
60Hz
frequency
50Hz
Ip = Ir x
0.6
0.65 0.7
0.75 0.8
0.85 0.9
0.95
tp@(1.2Ip)
15
25
35
Off
Setting range
80V ~ 0V_Pick-up
UV_Pick-up ~ 980V
6% ~ 99%
10~500 kW
500~5000 kW
6% ~ 99%
UF_Pick-up ~ 65
UF_Pick-up ~ 55
55Hz ~ OF_Pick-up
45Hz ~ OF_Pick-up
Pick-up
Step
1V
1V
1%
1kW
1kW
1%
1Hz
1Hz
1Hz
1Hz
10
Accuracy
5%
5%
2.5% or (*10%)
10%
10%
2.5% or (*10%)
0.1Hz
0.1Hz
0.1Hz
0.1Hz
20
30
Time delay(s)
Setting range Step Accuracy
1.2~40sec
0.2~40sec
0.1sec
0.1sec
1.2~40sec
A-2-72

type
S type:Supreme meter
Overload protection
-Long-time delay
-Thermal
Protection for Over voltage/Under voltage/Over
frequency/Under frequency/Unbalance/Reverse power
The fine-adjustable setting by knob and Key
IDMTL setting (SIT, VIT, EIT, DT curve)
- Basic setting : None. Thermal curve.
Measurement and Display Function
-High detailed measurement for 3 phase
current/Voltage/Power/Energy/
Phase angle/Frequency/PF/Demand
-128 x 128 Graphic LCD
-Indicates current/voltage Vector Diagram and
Waveform
Fault recording
-Records Max. up to 256 fault information about fault
type, fault phase, fault value, occurrence time of fault
-Fault wave recording: records the latest fault wave
Event recording
-Records events of device related to setting change,
operation and state change. (Max. up to 256)
Power quality analysis
-Measurement for 1st~63th harmonics
-THD, TDD, k-Factor
-Voltage/current waveform capture
3 DO(Digital output)
-Programmable for alarm, trip and general DO
Communication
-Modbus/RS485
-Profibus-DP
Graphic LCD: Indication of measurement and information

Alarm SP
Ir
Isd
Ii
Ig
Comm
Comm: LED indicating comm. state (Blink when running)

SP: Self-protection LED and battery test LED
Reset
Esc

(Rotation)
Ir: Long-time current setting, tr: Long-time tripping delay setting

A-2-73

Protection
t
Ir
tr
lsd
tsd
Ii
I
Long time
Current setting (A)
Time delay (s)
100ms
Short time
Current setting (A)
Accuracy: 10%
Time delay (s)
@ 10Ir
Iu = In...
tr@(1.5lr)
tr@(6.0lr)
tr@(7.2lr)
0.4
12.5
0.5
0.34
0.5
25
1
0.69
0.6
50
2
1.38
0.7
100
4
2.7
0.8
200
6
5.5
0.9
300
12
8.3
1.0
400
16
11
500
20
13.8
Off
Off
Off
Isd = Ir...
1.5
10
Off
0.2
0.2
0.3
0.3
0.4
0.4
80
160
260
360
140
240
340
440
tsd
(I2t Off)
Instantaneous
Current setting (A)
Tripping time
Ground fault
Pick-up (A)
20%(Ig0.4In)
Ig
Time delay (s)

@ 1In

Current setting (A)
Time delay (ms)
Accuracy: 15%
I n
0.05 0.1
0.1
20
Time(ms)
Max. Trip
80
Time(ms)
Ii = In...
2
3
4
50(10ms)
10
12
15
Off
Ig = In...
0.2
0.7
0.8
1.0
Off
10
20
30
Off
tg
tg
I2t Off
I2t On
Min. Trip
(I2t Off)
I2t Off
I2t On
Min. Trip
0.3
0.4
0.5
0.6
0.05 0.1
0.1
0.2
0.2
0.3
0.3
0.4
0.4
80
160
260
360
140
240
340
440
230
350
800
950
230
350
800
20
Time(ms)
Max. Trip
80
Time(ms)
In
0.5
Alarm
140
Time(ms)
Trip
140
Time(ms)

I
PTA(Pre Trip Alarm)

Current setting (A)
Time delay (s)
Accuracy: 15%
Other protection
Under voltage
Over voltage
Voltage unbalance
Reverse power
Over power
Current unbalance
Over
60Hz
frequency
50Hz
Under
60Hz
frequency
50Hz
Ip = Ir x
0.6
0.65 0.7
0.75 0.8
0.85 0.9
0.95
tp@(1.2Ip)
15
25
35
Off
Setting range
80V ~ 0V_Pick-up
UV_Pick-up ~ 980V
6% ~ 99%
10~500 kW
500~5000 kW
6% ~ 99%
UF_Pick-up ~ 65
UF_Pick-up ~ 55
55Hz ~ OF_Pick-up
45Hz ~ OF_Pick-up
Pick-up
Step
1V
1V
1%
1kW
1kW
1%
1Hz
1Hz
1Hz
1Hz
10
Accuracy
5%
5%
2.5% or (*10%)
10%
10%
2.5% or (*10%)
0.1Hz
0.1Hz
0.1Hz
0.1Hz
20
30
Time delay(s)
Setting range Step Accuracy
1.2~40sec
0.2~40sec
0.1sec
0.1sec
1.2~40sec
A-2-74

Operation characteristic
Long-time delay (L)
Iu
N, A type
.8
Ir
.9
.7
.88
.9
tr
.6
.83
.5
Iong time
.8
In
.93
.85
.95
.98
P, S type
.7
.8
20
.5
.9
(S)
12
.5
16
20
1
.4
Ir
Iong time
.5
In
off
@6 Ir
tr
characteristic in inverse ratio to fault current.
off
@6 Ir
tr
.6
The function for overload protection which has time delayed

12
16
Iu
Ir
1. Standard current setting knob: Ir

1) Setting range in P type and S type: (0.4-0.5-0.6-0.7-0.8-0.9-1.0)In
2) Setting range in N type and A type: (0.4 ~1.0)In
- Iu: (0.5-0.6-0.7-0.8-0.9-1.0)In
- Ir: (0.8-0.83-0.85-0.88-0.9-0.93-0.95-0.98-1.0)Iu
2. Time delay setting knob: tr
- Standard operating time is based on the time of 6Ir
- Setting range: 0.5-1-2-4-8-12-16-20-Off sec (9 modes)
3. Relay pick-up current
- When current over (1.15)Ir flows in, relay is picked up.
4. Relay operates basing on the largest load current among R/S/T/N phase.
Short-time delay (S)

The function for fault current (over current) protection which has definite
Isd
tsd
6
3
2
1.5
(S)
.3
10
.2
.4
.4
time characteristic and time delayed in inverse ratio to fault current.

.3
.2
.1
off
.1
short time
.05
on 2 off
Ir
I t
Isd
tsd
1. Standard current setting knob: Isd

- Setting range: (1.5-2-3-4-5-6-8-10-Off)Ir
2. Time delay setting knob: tsd
- Standard operating time is based on the time of 10Ir.
- Inverse time (I2t On): 0.1-0.2-0.3-0.4 sec
- Definite time (I2t Off): 0.05-0.1-0.2-0.3-0.4 sec
4. When ZSI function was set, the protection operation will take place instantaneously with
input absence by downstream devices. It is advised to disable its ZSI function on the last
downstream device.
Instantaneous (I)
The function for breaking fault current above the setting value within
Ii
the shortest time to protect the circuit from short-circuit.

10
12
15
1. Standard current setting knob: Ii

- Setting range: (2-3-4-6-8-10-12-15-Off)In
3. Total breaking time is below 50 (10)ms.
2
off
instantaneous
In
Ii
A-2-75
Ground Fault (G)

The function for breaking ground fault current above setting value
Ig
.5
.6
tg
.7
.4
(S)
.4
after time-delay to protect the circuit from ground fault.
.3
.4
.8
.3
.2
.3
.2
.1
.2
off
.1
ground fault
1. Standard setting current knob: Ig

- Setting range: (0.2-0.3-0.4-0.5-0.6-0.7-0.8-1.0-Off)In
2. Time delay setting knob: tg
- Inverse time (I2t On): 0.1-0.2-0.3-0.4 sec
- Definite time (I2t Off): 0.05-0.1-0.2-0.3-0.4 sec
3. Ground fault current is vector sum of each phase current. Therefore, 3Pole products may
operate under its phase-unbalance including ground fault situations.(R+S+T+(N) Phase)
downstream device.
5. Ground-fault functions are basically provided with products equipped with a trip relay through
its internal CT that is embedded in each phase.(But, it cant be used with earth-leakage
protection function at the same time)
.05
on 2 off
In
I t
Ig
tg
Earth Leakage (G) - Option

The function for breaking earth leakage current above setting value after
I n
(ms)
800
900
10
350
350
20
230
230
0.5
time delay to protect the circuit from earth leakage. (A, P, S type)
800
140
140
30
Earth Leakage trip alarm
1. Standard setting current knob: In

- Setting range: 0.5-1-2-3-4-5-10-20-30-Off (A)
2. Time delay setting knob: t
- Trip time: 140-230-350-800 ms
- Alarm time: 140-230-350-800-950 ms
3. Settings within its alarm range will prevent its breaker from tripping but activating its alarm.
4. This function is enabled and can be used only with standard ZCT provided by LS or private
external CT(secondary output 5A) selected by customers.
downstream device.
I n
Use cautions with earth-leakage current settings
R S T N
ZCT or External
CT
- When using a standard ZCT provided by LS, the setting range is from 0.5 to 30A which is
based on its primary current. But MCCB installed like A type (displayed on the left side)
should only be cable-connected and its rated current should be less than 1600A.
- When using other CT selected by customers, the setting range is from 0.5 to 5A based on
its secondary current.(Secondary output rating : 5A)
Hence, under 100:5A CT, if trip relay is set to 0.5A, earth-leakage exceeding 10A will
activate its operation (0.5A20 = 10A)
Guideline for the external CT usage
ZCT or External
CT
- Earth-leakage protection characteristics using the standard CT which is installed inside of

MCCB can protect currents from 20 to 100% range on its rated current.
- As rated currents on MCCB increases, current that is covered by its standard CT increase
as well. This can not protect against small leakage currents.
ex) 400A MCCB Min. Earth-leakage current 400A20% =80A
4000A MCCB Min. Earth-leakage current 4000A20% =800A
- Therefore, customers are advised to install an external CT in accordance with its rated
currents within its systems. And choose trip relay(E, X type) which is required with external
CT usage in order to provide earth-leakage functions.
A-2-76
A type
Measurement function
Class.
Measurement
element
Line current
Ia,Ib,Ic
Current
Normal current
I1
Voltage
Angle
P type
Power
Reverse current
I2
Vab,Vbc,Vca
Phase voltage
Va,Vb,Vc
Normal voltage
V1
Freq.
Unbalance
S type
80A~65,535A
1%
60~690V
0~360
V2
Line-to-current
VabVbc, VabVca
Phase-to-phase
VaVb,VaVc
Phase-to-current
VaIa, VbIb, VcIc
Active power
Pa(ab), Pb(bc), Pc(ca), P
kW
1kW~99,999kW
3%
Reactive power
Qa(ab), Qb(bc), Qc(ca), Q
kVar
1kVar~99,999kVar
3%
Apparent power
Sa(ab), Sb(bc), Sc(ca), S
kVA
1kVA~99,999kVA
3%
WHa(ab), WHb(bc),
kWh
WHc(ca), WH
MWh
1kWh~9999.99MWh
3%
1kVarh~9999.99MVarh
3%
1kWh ~9999.99MWh
3%
VARHa(ab), VARHb(bc),
kVarh
VARHc(ca), VARH
Mvarh
Reverse active
rWHa(ab), rWHb(bc),
kWh
energy
rWHc(ca), rWH
MWh
Frequency
Power factor(PF)
PFa(ab), PFb(bc), PFc(ca), PF
Unbalance rate
Iunalance, Vunbalance
0.0~100.0
Peak demand
kW
1kW~99999kW
Current demand
Peak demand
80A~65,535A
Voltage
1st~63th harmonics of
harmonics
Va(ab),Vb(bc),Vc(ca)
60~690V
Current harmonics
1st~63th harmonics of Ia,Ib,Ic
Hz
45~65Hz
+: Lead, -: Lag
80A~65,535A
THD, TDD
0.0~100.0
K-Factor
0.0~100.0
For P and S type Trip relay, separate voltage module is necessary

to measure other element besides current (Separate purchase is needed)
- Voltage input range: AC 60~690V
Vr Vs Vt Vn
Vr Vs Vt
Voltage
module
3P4W wiring
A-2-77
13
14
15
16
17
18
19
20
V1
V2
V3
Vn
1
2
3
4
5
6
7
8
9
10
11
12
1
1
Voltage module
1
2
3
4
5
6
7
8
9
10
11
12
1%
VabIa, VabIb, VabIc,
demand
Harmonics
Accuracy
Line-to-line
Active power
Demand
Display range
Reverse voltage
Reactive energy
Power factor
Unit
3%
Line voltage
Active energy
Energy
Detailed element
Voltage
module
3P3W wiring
13
14
15
16
17
18
19
20
V1
V2
V3
Vn

ZSI - Zone Selective Interlocking (A, P, S type)
Zone-selective interlocking drops delay time that eliminates faults for breakers.
It minimizes the shock that all kinds of electric machineries get under
fault conditions.
1. In case of that short time-delay or ground fault accident occurs at ZSI built in system,
the breaker at accident site sends ZSI signal to halt upstream breakers operation.
2. To eliminate a breakdown, trip relay of MCCB at accident site activates trip operation
without time delay.
3. The upstream breaker that received ZSI signal adhere to pre-set short time-delay or
ground fault time-delay for protective coordination in the system.
However upstream breaker that did not receive its signal will trip instantaneously.
4. For ordinary ZSI operation, it should arrange operation time accordingly so that downstream
circuit breakers will react before upstream ones under overcurrent/short time delay/
ground fault situations.
5. ZSI connecting line needs to be Max. 3m.
Z4
Z3
Z2
Z1
ZSI input
Fault A
Z4
Z3
Z2
Z1
ZSI output
ZSI input
Fault B
Z4
Z4
Z4
Z3
Z3
Z3
Z2
Z2
Z2
Z1
Z1
Z1
1) Occurrence of fault A
- Only breaker performs instantaneous trip operation.
2) Occurrence of fault B
- Breaker performs instantaneous trip operation,
breaker performs trip operation after prearranged delay time
- But if breaker did not break the fault normally,
breaker performs instantaneous trip operation to protect system.
A-2-78

Remote reset and digital I/O (A, P, S type)
In case of that MCCB operates due to accidents or over current,

Trip relay indicates the information of the accident through the LED and LCD.
Trip relay A, P and S type is possible to perform the remote reset by digital input,
and have 3 DO(Digital output).
1. Methods to reset Trip relay is to push the Reset button on the frontal side and to
use the remote reset.
2. Digital input
- [R11-R22] input: Remote reset
- [Z1-Z2] Input: ZSI input
- [E1-E2] Input: ZCT for earth leakage detection or external CT input
All DI are dry contact that has 3.3V of recognition voltage. When inputting close by
SSR(Solid State Relay) or open-collector, connect collector(Drain) to R11.
V2
V3
Vn
E1
Z3
Z1
Common
Reset
ZCT
V1
ZSI input
Voltage module
ZSI output
3. Digital output 3a(524, 534, 544-513)

- Fault output: Long/Short time delay, Instantaneous, Ground fault, UVR, OVR, UFR,
OFR, rPower, Vunbal, Iunbal
(Maintains state as Latch form until user pushes reset.)
- General DO: when setting L/R as remote, it is available to control close/open
remotely by using communication.
485+
R11
R22
513
544
534
524
Power supply
R2
R1
485-
Trip
Relay
A-2-79
Digital
Output
LTD
Z2
GTD
Z4
S/I
Trip relay
Long Short Instantaneous Ground Overload OVR UVR rPower Vunbal Iunbal OFR UFR OPR
Alarm
time time
DO1(524)
P, S DO2(534)
type
DO3(544)
DO1(524)
A type DO2(534)
DO3(544)
Not available
Note
Programmable
Fixed

Communication
Modbus/RS-485
Operation mode: Differential
Distance: Max. 1.2km
Cable :
General RS-485 shielded twist
2-pair cable
Baud rate :
9600bps, 19200bps, 38400bps
Transmission method: Half-Duplex
Termination: 150
SCADA system
Modbus/RS-485
Profibus-DP
Profibus-DP module is installed
separately (Option)
Operation mode: Differential
Distance: Max. 1.2km
Cable :
Profibus-DP shielded twist 2-pair cable
Baud rate: 9600bps~12Mbps
Transmission method: Half-Duplex
Termination: 150
Standard: EN 50170 / DIN 19245
Ethernet/TCP/IP
Area
controller
TCP/IP/Ethernet
TCP/IP
CNC
Profibus-FMS
PC
DCS
PLC
Profibus-DP
Profibus-DP
communication module
(Option)
Profibus-DP
communication
module (Option)
PLC
Modbus/RS-485
A-2-80

Event & fault recording (P, S type)
When there are events such as setting change, Info. change, error of self-diagnose,
state change, P and S type record Max. up to 256 information of the events in accordance with
time(ms). In addition, they can record Max. up to 256(up to 10 for A type) information of the faults
such as fault cause, fault phase, fault value and so on in accordance with time(ms).
Event information display

Initial display
Setting display
1000 A
R
100%
50%
Password
input
1.H/W Set
2.Relay Set
3.Events
4.Sys Info
5.L/R [L]
1.Event
2.Clear All
3.Fault
4.Clear All
1. EventL
2007/05/15
20:29:41
Sta Change
10. EventL
2007/04/15
10:11:24
Cfg Change
Power On
Comm Set up
Fault information display

Initial display
Setting display
1000 A
R
100%
50%
Password
input
1.H/W Set
2.Relay Set
3.Events
4.Sys Info
5.L/R [L]
1.Event
2.Clear All
3.Fault
4.Clear All
1. Trip
2007/04/26
08:35:52
OCR-Short
9. Trip
2007/04/11
09:11:32
UVR
Phase T
Phase R
930A
System information
P and S type can indicate information as followings with the information of the MCCB.
- Present time: year/month/date/hour/minute/ms
- MCCB current ratings
- N-phase current ratings: 100%
- Frequency information: 60Hz / 50Hz
- Closing numbers of breaker: CB ON numbers
- Trip relay operating time: OCR ON time
- ON time of breaker: CB ON time
- S/W ver. information
System information display

Initial display
Setting display
1000 A
R
100%
50%
A-2-81
1.H/W Set
2.Relay Set
3.Events
4.Sys Info
5.L/R [L]
Password
input
System Info
Date Time
2007/05/15 21:23:30
Rating
1000 A
Ex-Func 4POCGR
Freq
60 Hz
CB ON# 23
Ver-Arm 1.41
System Info
Date Time
2007/05/15 21:23:30
Rating
1000 A
Ex-Func 4POCGR
T-OPER 220 h
T-CB ON 180 h
Ver-Msp 1.01
OV

System block diagram
N
ACB Trip
ACB
Vcc/+9V/-9V
CN2-1
CN2-11
Filter
Amp.
CN2-3
CN2-13
Signal CT
CN2-5
CN2-15
Vcc
CPU
Output
Power PCB
Assy
+5V
+24V
Display
(LED, LCD)
Main PCB
Assy
MTD
CN2-6
Output
CN2-8
Main PCB
Assy
CN2-7
CN2-16
CN2-14
Setting
part
GND 24
CN2-4
Vcc
Self
power
RY0 (K1)
CN4-2
GTD contact
+24V
GND+24V
Power CT
Main PCB
Assy
RY1 (K2)
CN4-4
STD/INST contact
+5V
RY2 (K3)
-5V
CN4-6
LTD contact
CN2-2
CN4-9
SMPS
CN4-10
Power PCB
Assy
CN4-8
Common contact
Trip relay
Additional source
AC/DC 100~250V
DC 24~60V
CN1-1
ZSI output+ terminal
CN1-2
ZSI output- terminal
CN1-3
ZSI input+ terminal
CN1-4
ZSI input- terminal
CN1-9
CN1-10
VDM
CN1-11
CN1-12
CN1-5
Remote reset+ terminal
CN1-6
Remote reset- terminal
CN1-7
Earth
CN1-8
CN1-7
Earth leakage+ terminal
Input signal(R phase) CN3-2

Input signal(S phase) CN3-4
CN1-8
Earth leakage- terminal
Input signal(T phase) CN3-6

Input signal(N phase) CN3-8
DC 24V
CN3-5
UTXO
CN3-1
URXO
CN3-3
GND 24V
CN3-7/9
AD GND
CN3-10
Test
Main PCB
Assy
Comm.
Power PCB
Assy
CN4-1
485+ terminal
CN4-3
485- terminal
A-2-82

Installation and Handling
Withdrawal Wiring for Trip Relay

Caution
1. In case of disassembling and assembling the main cover, screw should be tightened in specific torque of1.5N.m
(15.3kgf.cm)
2. In case of disassembling and assembling the main cover by over tightening torque, the parts of MCCB can be damaged.
10P Connector
Terminal ASS'Y, Short ZSI IN

1ea
CONN.,172501-1, AMP
1ea
Terminal,172773-1, AMP
25ea
Wire ASSY 1ea

12P Connector
WIRE ASSY OCR types

No.
Drawing No.
Part Name
Functions
OCR
76671176262
WIRE ASSY AG AC OCR
Communication, Digital Output, ZSI, Remote Reset
A Type
76671176263
WIRE ASSY A ZK PS CKA OCR
76671176264
WIRE ASSY AE AX PX SX OCR
Communication, Digital Output, ZSI, Remote Reset,

Earth Leakage(<30A), Voltage Module
Communication, Digital Output, ZSI, Remote Reset,
Earth Leakage(>30A), Voltage Module
P, S Type
P, S Type
Components of wire assy OCR and types

Terminal number and Description
Number
Marking
04 03
01
485+
Comm. +
06 05
02
485-
Comm. -
08 07
03
R1
Power +
10 09
04
R2
Power -
05
524
Relay Output (Long time)
06
534
Relay Output (Short time/Instantaneous)
07
544
Relay Output (Ground fault/PAL)
08
513
Relay Output Common
09
Z3
ZSI Out +
10
Z4
ZSI Out -
11
Z1
ZSI In +
12
Z2
13
R11
Remote Reset +
14
R22
Remote Reset -
15
E1 or B1
Earth Leakage +
16
E2 or B2
Earth Leakage -
17
V1
VR Input
18
V2
VS Input
19
V3
VT Input
20
VN
V Input Common
02
01
12
11
14
13
16
15
18
17
20
19
01
02
A-2-83
Description
ZSI In -
1. Disassembling cover and short connector

In case of not using ZSI function
Conn.,172501-1, AMP
Terminal ASS'Y,
Short ZSI IN
No. 11, 12 Shorted
Caution
TRIP or OFF STATE
Caution : If not using ZSI function of Trip

Relay (OCR), please short ZSI
INPUT of terminal No.11,12 (ZSI IN
+, ZSI IN-) by using the TERMINAL
ASSY,SHORT ZSI IN
2. Assembly of wire assy and withdrawal of wire

Caution : Please
dont place the
wires below the
guide line
10P Connector
In case of the wiring of Earth Leakage 30A

Drawing No.
Part Name
76671176264
WIRE ASSY AE AX PX SX OCR
12P Connector
No. 15, B1
No. 16, B2
User wiring E1, E2
A-2-84

Installation of withdrawal wiring for Trip Relay
Trip Relay (OCR) type and applied wire assy

WIRE ASSY, [
No
Type
] ,OCR,TS1600
[AG AC]
[A ZK PS CKA]
[AE AX PX SX]
76671176262
76671176263
76671176264
WIRE ASSY, [
] ,OCR,TS1600
No
Type
[AG AC]
[A ZK PS CKA]
[AE AX PX SX]
NG0
33
PC1
76671176262
76671176263
76671176264
NG5
34
PC2
AG0
35
PC6
AG1
36
PC7
AG2
37
PK1
AG5
38
PK2
AG6
39
PK6
AG7
40
PK7
AZ0
41
PX1
10
AZ1
42
PX2
11
AZ2
43
PX6
12
AZ5
44
PX7
13
AZ6
45
PA1
14
AZ7
46
PA2
15
AE0
47
PA6
16
AE1
48
PA7
17
AE2
49
SC1
18
AE5
19
AE6
50
SC2
51
SC6
20
AE7
52
SC7
21
AC1
53
SK1
22
AC2
54
SK2
23
AC6
55
SK6
24
AC7
56
SK7
25
AK1
57
SX1
26
AK2
58
SX2
27
AK6
59
SX6
28
AK7
60
SX7
29
AX1
61
SA1
30
AX2
62
SA2
31
AX6
63
SA6
32
AX7
64
SA7
65
NV1
66
NV6
A-2-85
A-3. Accessories
Accessories for TE series
Overview
Electrical auxiliaries
Rotary handles
Terminals
Insulation
Interlock
A-3-1
A-3-2
A-3-5
A-3-6
A-3-7
A-3-8
Accessories for TD, TS up to 800A

Overview
Rotary handles
Locking devices
Terminals
Insulation
Mechanical interlocking device
Plug-in device
Connector KIT
Remote operation
Residual Current Devices (RCD)
Standard accessories
A-3-9
A-3-10
A-3-14
A-3-16
A-3-19
A-3-24
A-3-26
A-3-27
A-3-32
A-3-34
A-3-35
A-3-39
Accessories for TS up to 1600A

Overview
OCR Tester [OT]
UVT Time Delay Controller [UDC]
Rotary handles
Locking devices
Terminals
Insulation
A-3-40
A-3-41
A-3-45
A-3-46
A-3-47
A-3-51
A-3-53
A-3-56
A-3-57

Overview
Circuit breaker
Insulation barrier
Terminal cover(short, long)

Connection terminals
Direct rotary handle

Extended rotary handle
Mechanical interlock device
A-3-1

Auxiliary and Alarm switch
Auxiliary switch (AX)

Auxiliary switch is for applications requiring remoteONandOFFindication.
Each switch contains two contacts having a common connection.
One is open and the other closed when the circuit breaker is open, and viceversa.
Alarm switch (AL)

Alarm switches offer provisions for immediate audio or visual indication of a tripped breaker due to
overload, short circuit, shunt trip, or undervoltage release conditions.
They are particularly useful in automated plants where operators must be signaled about changes
in the electrical distribution system. This switch features a closed contact when the circuit breaker
is tripped automatically. In other words, this switch does not function when the breaker is operated
manually.
Its contact is open when the circuit breaker is reset.
Combination switch (AX+AL)

It consists of one auxiliary switch (AX) and one alarm switch (AL) in a body to connect into the
same position of the breaker.
Contact
MCCB
ON
OFF
TRIP
AX
AL
Rating
Conventional thermal current, Ith
5A
Rated operational current, Ie
Current, Ie
Voltage, Ue
AC 50/60Hz
DC
Resistive load
Inductive load
125V
250V
500V
30V
125V
0.4
0.4
250V
0.2
0.2
A-3-2

Shunt trip, SHT
The shunt trip opens the mechanism in response to an externally applied voltage signal. The
releases include coil clearing contacts that automatically clear the signal circuit when the
mechanism has tripped.
The shunt release can be installed in the right accessory compartment of the MCCBs.
- Range of operational voltage
AC: 0.7~1.1Vn, DC: 0.8~1.1Vn
- Frequency(Only AC): 45Hz ~ 65 Hz
Rating
Power consumption
Control voltage, Ue
Voltage
A-3-3
AC (VA)
DC (W)
mA
AC/DC 12V
0.35
0.36
30
AC/DC 24V
0.64
0.65
27
AC/DC 48V
1.09
1.1
23
AC/DC 60V
1.2
1.22
20
AC/DC 100~130V
0.73
0.75
5.8
AC/DC 200~250V
1.21
1.35
5.4
AC 380~450V
1.67
3.8
AC 440~500V
1.68
3.5
Max.opening time
50ms (max.)
Tightening torque of terminal screw
8.2 kgfcm

Undervoltage release, UVT
The undervoltage release automatically opens a circuit breaker when voltage drops to a value
ranging between 20% to 70% of the line voltage. The operation is instantaneous, and after tripping,
the circuit breaker cannot be re-closed again until the voltage returns to 85% of line voltage.
Continuously energized, the undervoltage release must be operating before the circuit breaker can
be closed. The undervoltage release can be easily installed in the right accessory compartment of
the MCCBs.
- Range of tripping voltage: 0.2 ~ 0.7Vn
- MCCB making is possible voltage: 0.85Vn (Exceed)
- Frequency (Only AC): 45Hz ~ 65Hz
Rating
Power consumption
Control voltage, Ue
Voltage
AC (VA)
DC (W)
mA
AC/DC 24V
0.64
0.65
27
AC/DC 48V
1.09
1.1
23
AC/DC 100~110V
0.73
0.75
5.8
AC/DC 200~220V
1.21
1.35
5.4
AC 380~440V
1.67
3.8
AC 440~480V
1.68
3.5
Max.opening time
50ms (max.)
8.2 kgfcm
Operating
Trip
20~70% Vn
voltage range
Reset/Closing
0.85Vn
Maximum possibilities
Position
Type
TE160
3/4P
Left-hand seat
Right-hand seat
AX
AL
AX
AL
SHT/UVT
Note) Right-hand seat can be installed only one Electrical Accessary
A-3-4

Rotary handles
The rotary handle operating mechanism is available in either the direct version or in the extended
version on the compartment door.
It is always fitted with a compartment door lock and on a request it can be supplied with a key lock
in the open position.
Direct rotary handles

MCCB
Rotary handle
TE160
DH1E
Extended rotary handles

MCCB
Rotary handle
TE160
EH1E
Degree of protections
Type
IP
The access probe of 1.0mm diameter

DH1E
shall not penetrate
IP40
Totally protected against ingress of

EH1E
A-3-5
dust and water jets from any direction
IP55

Terminals
Front connection
Extended terminal
- As an optional part of circuit breaker
- Can increase the pitch of the terminals
MCCB
Pole
Type
TE100
3P
ET13E
TE160
4P
ET14E
Feature
Rear connection
Rear connection terminals are used to adapt Susol TE circuit breakers to switchboards or
other application that require rear connection.
These can be connected directly to circuit breakers without any modification.
Flat terminals
MCCB
Pole
Type
TE100
3P
RTF13
TE160
4P
RTF14
Feature
A-3-6

Insulation
Insulation by barrier
These allow the insulation characteristics between the phases at the connections to be increased.
They are mounted from the front, even with the circuit-breaker already installed, inserting them into
the corresponding slots.
They are incompatible with both the insulating terminal covers.
It is possible to mount the phase separating partitions between two circuit-breakers side by side.
Type
Applied MCCB
B13C
TE100, TE160
Set quantity
3P
4P
4pcs
6pcs
Insulation by terminal cover

Insulation terminal cover
The terminal covers are applied to the circuit-breaker to prevent accidental contact with live parts
and thereby guarantee protection against direct contacts.
Short type covers
Two types by length are available:

Short type covers, ITS
- IP40 degree of protection
- For fixed circuit-breakers with rear terminals and for moving parts of plug-in
Long type covers, ITL
- For fixed circuit-breakers with front, front extended, front for cables terminals.
Type
Frame type
Long type covers
A-3-7
TE100, TE160
Terminal cover
pole
Long type
Short type
3P
ITL13E
ITS13E
4P
ITL14E
ITS14E

Interlock

The mechanical interlock (MIT) can be applied on the front of two breakers mounted side by side,
in either the 3-pole or 4-pole version and prevents simultaneous closing of the two breakers.
Fixing is carried out directly on the cover of the breakers.
The front interlocking plate allows installation of a padlock in order to fix the position. (possibility of
locking in the O-O position as well)
Mechanical Interlock
(Padlocks are not supplied)
This mechanical interlocking device is very useful and simple for consisting of manual sourcechangeover system.
MCCB
Operation
Frame type
TE100, TE160
Left MCCB: ON/OFF is possible

Right MCCB: Off lock
Interlock
pole
3P
MIT13E
4P
MIT14E
Interlock handle
Interlock bar
Left MCCB: Off lock

Right MCCB: ON/OFF is possible
Both MCCBs are of locked

Note) Terminal covers do not use with the interlock.
A-3-8
Accessories for TD/TS series up to 800A

Overview
Circuit breaker
Plug-in base
Insulation barrier
Terminal cover (Short, Long)

Connection terminals
Motor operator
Aux. handle
Locking devices (Removable, Fixed)
Mechanical interlock device

Trip units
A-3-9

The following devices are installed into all TD & TS circuit breakers regardless of frame size.
And, the electrical auxiliaries can be easily installed in the accessory compartment of the circuit
breakers which is cassette type.
Undervoltage release, UVT

The undervoltage release automatically opens a circuit breaker when voltage drops to a value
ranging between 35% to 70% of the line voltage. The operation is instantaneous, and after tripping,
the circuit breaker cannot be re-closed again until the voltage returns to 85% of line voltage.
Continuously energized, the undervoltage release must be operating before the circuit breaker can
be closed. The undervoltage release can be easily installed in the left accessory compartment of
the Susol TD and TS circuit-breakers.
UVT
- Range of tripping voltage: 0.35 ~ 0.7Vn

- MCCB making is possible voltage: 0.85Vn (exceed)
- Frequency (only AC): 45Hz ~ 65Hz
Technical data
Consumption
Control voltage (V)
Power
consumption
Applicable
AC (VA)
DC (W)
mA
AC/DC 24V
0.64
0.65
27
AC/DC 48V
1.09
1.10
23
AC/DC 110~130V
0.73
0.75
5.8
AC 200~240V/DC 250V
1.21
1.35
5.4
TD100, TD160,
AC 380~440V
1.67
3.8
TS100, TS160,
AC 440~480V
1.68
3.5
TS250, TS400,
Max.opening time (ms)

50
MCCBs
TS630, TS800
8.2kgfcm
Transformer operating voltage (V)

- Drop (Circuit breaker trips)
- Rise (Circuit breaker can be switched on)
0.7~1.35Vn
~0.85Vn
8.2kgfcm
A-3-10

Shunt release, SHT

The shunt release opens the mechanism in response to an externally applied voltage signal. The
releases include coil clearing contacts that automatically clear the signal circuit when the
mechanism has tripped.
The shunt release can be installed in the left accessory compartment of the Susol TD & TS circuitbreakers.
- Range of operational voltage: 0.7 ~ 1.1Vn
- Frequency (only AC): 45Hz ~ 65Hz
SHT
Technical data
Consumption
Control voltage (V)
AC (VA)
DC 12V
Applicable
mA
0.36
30
0.58
0.58
24
MCCBs
Power
AC/DC 24V
consumption
AC/DC 48V
1.22
1.23
25
TD100, TD160,
AC/DC 110~130V
1.36
1.37
10.5
TS100, TS160,
AC 220~240V/DC250V
1.80
1.88
7.5
TS250, TS400,
AC 380~500V
1.15
2.3
TS630, TS800
Max.opening time (ms)
50
8.2kgfcm
8.2kgfcm
Click
A-3-11
DC (W)

Auxiliary switch (AX), Alarm switch (AL) and Fault alarm switch (FAL)
Auxiliary switch is for applications requiring remote ON and OFF indication.
One is open and the other closed when the circuit breaker is open, and vice-versa.
AX
Alarm switch (AL)

Alarm switches offer provisions for immediate audio or visual indication of a tripped breaker due to
overload, short circuit, shunt trip, or undervoltage release conditions.
They are particularly useful in automated plants where operators must be signaled about changes
in the electrical distribution system. This switch features a closed contact when the circuit breaker
is tripped automatically. In other words, this switch does not function when the breaker is operated
manually.
Fault alarm switch (FAL)
FAL Indicates that the breaker has tripped due to overload or short circuit.
And, it can be applied to only circuit breakers with electronic trip units.
Contact operation
AL
MCCB
Position
ON
OFF
TRIP
AXa1
AXa1
AXc1
of AX
AXc1
AXb1
AXb1
Position
of
AXa1
AXa1
AXc1
AXc1
AL, FAL
AXb1
AXb1
Technical data
Conventional thermal current Ith
Rated operational current Ie
5A
Voltage
with rated operational voltage Ue

- Altemating current 50/60Hz AC
- Direct current DC
TD100
Ie
Resistance
Inductance
125V
250V
500V
30V
125V
0.4
0.4
250V
0.2
0.2
TD160
TS100
TS160
TS250
TS400
TS630
TS800
A-3-12

Possible configuration of electrical auxiliaries

Maximum possibilities
Phase
Accessory
TD160
TS250
TS630
TS800
AX
R (Left)
AL
SHT or UVT
AX
AL
FAL
T (Right)
Note) FAL can be applied to only MCCB with electronic trip release.
TD160
TS250
TS630
TS800
AL
AX AX
AX
AL
*FAL
AX
AX AX AX
SHT/
UVT
AX AX AX
AL AL
AL
SHT/
UVT
*FAL
*FAL
SHT/
UVT
SHT/
UVT
A-3-13

Rotary handles
Rotary handles
in the open position.

MCCB
Rotary handle
TD100,TD160
DH1
TS100,TS160,TS250
DH2
TS400,TS630
DH3
TS800
DH4
Locked
Direct rotary handles with a key lock

MCCB
Unlocked
Padlockable device
TD100, TD160
DHK1
TS100, TS160, TS250
DHK2
TS400, TS630
DHK3
TS800
DHK4
Lock function
Lock in On or Off position
OFF position
Direct rotary handle with a key lock
MCCB
Padlockable device
TD100,TD160
EH1
TS100,TS160,TS250
EH2
TS400,TS630
EH3
TS800
EH4
Padlocks can be used to lock the breaker in the ON or OFF position.
Padlocks for direct or extended handle
A-3-14

Rotary handles
Rotary handles
Type
Circuit breaker with cover frame and
IP
IP40
Totally protected
rotary extended handle
against ingress of
dust and water jets from any
direction
A-3-15
IP65

Locking devices
Removable locking device

Removable locking device is available for all TD & TS circuit breakers.
The locking device is designed to be easily attached to the circuit-breaker.
This device allows the handle to be locked in the OFF position.
Locking in the OFF position guarantee isolation according to IEC 60947-2.
The locking device for the toggle handle can be installed in 3-pole and 4-pole circuit-breakers.
Maximum three (3) padlocks with shackle diameters ranging from 5 to 8mm may be used.
Removable locking device
MCCB
Padlockable device
TD100,TD160
PL1
TS100,TS160,TS250
PL2
TS400,TS630
PL3
TS800
PL4
Function
OFF position
Cover Aux.
Pad-lock
5~8
30
Padlock dimensions
A-3-16

Locking devices
Fixed locking device

Fixed locking device is available for all TD & TS circuit breakers.
This device allows the handle to be locked in the ON and OFF position.
The locking device for the toggle handle can be installed in 3-pole and 4-pole circuit-breakers.
Fixed locking device

MCCB
Padlockable device
TD100,TD160
PHL1
TS100,TS160,TS250
PHL2
TS400,TS630
PHL3
TS800
PHL4
Function
Lock in Off or On position
5~8
How to use
The locking device for the toggle handle is designed to be easily attached to
the front of circuit-breaker.
Please set the toggle handle in the position of On or Off.
Install the lock device onto the front of auxiliary cover of circuit breaker.
Folding the wings of lock device as shown in picture 3.
The padlock to be used shall be that which is commercially available with
the nominal dimension. (30mm nominal dimension, 5~8mm diameter)
TD100, 160
TS100 ~
TS800
A-3-17
30
Padlock dimensions

Locking devices
Locking by rotary handle with a key lock

A locking can be done by using the rotary handle which has key lock device.
The lock is used to lock the circuit-breaker in the OFF position.

Locked
Unlocked
MCCB
Padlockable device
TD100,TD160
DHK1
TS100,TS160,TS250
DHK2
TS400,TS630
DHK3
TS800
DHK4
Function
Lock in Off position
OFF position
Padlocking by rotary handle

A padlocking can be also done by using the rotary handle.
The lock is used to lock the circuit-breaker in the ON and OFF position.
1
2
Open Panel Door
Releasing panel door lock at ON position

The panel door can be locked at ON and TRIP position of rotary handle.
To open the panel door at ON position, just rotate release screw clockwise.
Reledsing
A-3-18

Terminals
Front connection
Terminal mounter
- It is supplied with Susol MCCBs as an standard part of circuit breaker.
- Connecting part with terminal for bus bar, cable with lug
MCCB
Type
TD100,TD160
TM1
TS100,TS160,TS250
TM2
TS400,TS630
TS800
Inner box terminal

- Bare cable connectors for Susol TD and TS series circuit breakers
- Can be used for both aluminum and copper cables
Cable
Applicable to
Type
Pole Set quantity connection
Conductor size
possibilities
TD100, 160
TS100, 160, 250
SBT13
1 Set (3EA)
SBT14
1 Set (4EA)
SBT23
1 Set (3EA)
SBT24
1 Set (4EA)
IBT33
1 Set (3EA)
IBT34
1 Set (4EA)
Note1)
TS400, 630
Note2)
PB12, 13
IBT13
1 Set (3EA)
IBT14
1 Set (4EA)
IBT23
1 Set (3EA)
IBT24
1 Set (4EA)
Note2)
PB22, 23
Note) 1. IBT3 for TS630 can be applied in case that rate current is upto 400A.
2. IBT13, 14 and IBT23, 24 are for Plug-in base.
A-3-19
L(mm)
21
S(mm2)Cu/Al
2.5~95
Tightening torque (kgfcm)
120~147
L(mm)
21
S(mm2)Cu/Al
10~150
120~147
L(mm)
30
S(mm2)Cu/Al
70~300
367~428
L(mm)
18
S(mm2)Cu/Al
2.5~95
306
L(mm)
21
S(mm2)Cu/Al
10~150
306

Terminals
Front connection
Extended box terminals (Copper cables/bars and aluminum cables)
- The extended box terminals for TD and TS circuit breakers can be used for cooper cables/bars
and aluminum cables. There are four (4) kinds of terminals.
- For TD100, TD160: 1-cable connector (EBT13, EBT14)
- For TS100, TS160, TS250: 1-cable connector (EBT23, EBT24)
- For TS400, TS630: 2-cable connector (EBT33, EBT34)
- For TS800: 3-cable connector (EBT43, EBT44)
Cable
Applicable to
Type
Pole Set quantity connection
Conductor size
possibilities
1-cable connector
TD100, 160
2-cable connector
TS100, 160, 250
TS400, 630
EBT13
1 Set (3EA)
EBT14
1 Set (4EA)
EBT23
1 Set (3EA)
EBT24
1 Set (4EA)
EBT33
1 Set (3EA)
EBT34
1 Set (4EA)
L(mm)
20
S(mm2)Cu/Al
2.5~95
306
L(mm)
24
S(mm2)Cu/Al
10~150
306
L(mm)
33 or 62
S(mm2)Cu/Al
285 to 2240
367~428
L(mm)
25~48
S(mm2)Cu/Al
385 to 3240
367~428
TS800
EBT43
1 Set (3EA)
EBT44
1 Set (4EA)
3-cable connector
A-3-20

Terminals
Front connection
Spreaders
MCCB
102.5
A
30
30
20
Type
2P
SP12a
3P
SP13a
4P
SP14a
2P
SP12b
3P
SP13b
4P
SP14b
2P
SP22a
3P
SP23a
4P
SP24a
2P
SP22b
3P
SP23b
4P
SP24b
Size A
(mm)
35
33
22
8.2
Pole
102.5
TD100, 160 3P
A
30
30
30
TD100, TD160
20
33
22
8.2
45
TD100, 160 4P
100
35
35
24
45
31
20
8.2
TS100, 160, 250 3P

A
100
35
35
TS100, TS160, TS250
35
24
31
20
8.2
TS100, 160, 250 4P
A-3-21
52.5
Feature

Terminals
Front connection
Spreaders
MCCB
27
Pole
Type
2P
SP32a
3P
SP33a
4P
SP34a
2P
SP32b
3P
SP33b
4P
SP34b
2P
SPS32
3P
SPS33
4P
SPS34
2P
SPS42
3P
SPS43
4P
SPS44
Size(mm)
A
52.5
41
70
54
46.5
41
70
81.5
Feature
TS400, 630 3P
TS400, TS630
27
TS400, 630 4P
49
TS800 3P
TS800
49
TS800 4P
A-3-22

Terminals
Rear connection
Rear connection terminals are used to adapt Susol TD and TS circuit breakers to switchboards or
other applications that require rear connection.
These can be connected directly to circuit breakers without any modification
There are two kinds of rear connection terminals.
- Flat type
- Round type
Flat type
Flat vertical terminals
MCCB
2-pole
3-pole
4-pole
TD100,TD160
RTB12
RTB13
RTB14
TS100,TS160,TS250
RTB22
RTB23
RTB24
TS400,TS630
RTB32
RTB33
RTB34
TS800
RTB42
RTB43
RTB44
4-pole
2,3-pole
TD160,TS250
BOLT, HEX, SOCKET, P.S/W, M6, L15
Torque: M6 (51.1 ~ 64.9kgf cm)
TS630
TS800

WASHER SPRONG LOCK D10
WASHER PLAIN D10
Torque: M8 (119 ~ 151kgf cm)

Torque: M12 (423 ~ 537kgf cm)
12.5 (M12: 423 ~ 537kgf cm)
Flat type
45
8=360
45
8.4 (M8: 119 ~ 151kgf cm)
8=360
Round type
Round threaded terminals
MCCB
4-pole
2,3-pole
Round type
A-3-23
2-pole
3-pole
4-pole
TD100,TD160
RTR12
RTR13
RTR14
TS100,TS160,TS250
RTR22
RTR23
RTR24
TS400,TS630
TS800

Insulation
Insulation by terminal cover

Insulation terminal cover
The terminal covers are applied to the circuit-breaker to prevent accidental contact with live parts
and thereby guarantee protection against direct contacts.
Short type covers
Two types by length are available:

Short type covers, ITS
- For fixed circuit-breakers with rear terminals and for moving parts of plug-in
Long type covers, ITL
- For fixed circuit-breakers with front, front extended, front for cables terminals.
MCCB
Frame type
TD100,TD160
TS100,TS160,TS250
TS400,TS630
Long type covers
TS800
Terminal cover
Pole
Long type
Short type
2P (1) , 3-pole
ITL13
ITS13
4-pole
ITL14
ITS14
2P (1), 3-pole
ITL23
ITS23
4-pole
ITL24
ITS24
2P (1), 3-pole
ITL33
ITS33
4-pole
ITL34
ITS34
2P (1), 3-pole
ITL43
ITS43
4-pole
ITL44
ITS44
Note) (1) 2P in 3pole mold case
A-3-24

Insulation
Insulation by barrier
These allow the insulation characteristics between the phases at the connections to be increased.
They are mounted from the front, even with the circuit-breaker already installed, inserting them into
It is possible to mount the phase separating partitions between two circuit-breakers side by side.
Type
A-3-25
Set quantity
TD100, TD160
4pcs
TS100, TS160, TS250
4pcs
B-33C
TS400, TS630
4pcs
B-43C
TS800
4pcs
B-23C
Insulation barriers
Applied MCCB

Interlock

Mechanical Interlock
This mechanical interlocking device is very useful and simple for consisting of manual sourcechangeover system.
Operation
MCCB
Frame type
TD100,TD160
TS100,TS160,TS250
Left MCCB: ON/OFF is possible
Right MCCB: Off lock
Interlock
Pole
TS400,TS630
TS800
3-pole
MIT13
4-pole
MIT14
3-pole
MIT23
4-pole
MIT24
3-pole
MIT33
4-pole
MIT34
3-pole
MIT43
4-pole
MIT44
Interlock handle
Left MCCB: Off lock

Right MCCB: ON/OFF is possible
Interlock bar
Both MCCBs are of locked
A-3-26

Plug-in device
Plug-in device
The plug-in base is the fixed part of the plug-in version of the circuit-breaker.
It will be installed directly on the back plate of panel.
The circuit-breaker is racked out by unscrewing the top and bottom fixing screws.
Plug-in base makes it possible to extract and/or rapidly replace the circuit breaker
without having to touch connections for ship and important installations.
MCCB
TD100, TD160
TS100, TS160, TS250
TS400, TS600
TS800
Pole
Arrangement
Type
Single line
PB12
Means
Single line
PB13
Double line
PB12D2
For distribution board
Double line
PB13D2
For distribution board
Single line
PB22
Single line
PB23
Single line
PB32
Single line
PB33
Single line
PB42
Single line
PB43
Front connection
DIN-rail
Back cover
Rear connection
A-3-27

Plug-in system
type
Normal type Plug-in MCCB: PB
- MCCB rating: TD100~TS800
- generally used in switchgears
D2 type
Double-row type Plug-in MCCB: PB
- MCCB rating: TD100, 160
- generally used in branch circuits
A-3-28

Plug-in device
Assembling procedure
TD100, TD160
1. Conversion to Plug-in MCCB
Disassemble terminal mounter.
HEX, Socket bolt(M615)
58kgf cm
Socket upper contact
Upper contact
2. Assembling safety device
M312 (Tap)
Safety device
3. Assembling MCCB and plug-in device
M480
Screw up M480 after
Instolling MCCBs
to boses
M480
A-3-29
M412

Plug-in device
TS100, TS160, TS250
Disassemble terminal mounter.
HEX, Socket bolt(M615)
58kgf cm
Socket upper contact
Upper contact
M312 (2EA)
Safety device
M480 (4EA)
A-3-30

Plug-in device
TS400, TS630
TS800

Socker upper contact
HEX, Socker bolt (M820)

135kgf cm
M1230 (HEX, Socker bolt)

480kgf cm
Contact upper
Upper contact
M38 (2EA)
Safety device
M312 (2EA)
Safety device

Nut special(M6)
M585 (4EA)
A-3-31

Connector KIT
Electric auxilialy circuit(AX, AL, SHT, UVT) from Breaker via one to
three connector KIT(nine wires each). These are made of moving part on Breaker and
fixed part on plug-in base up to 800AF.
Breaker Max.
TD160
TS250
TS400/630
TS800
Q'ty
1
Fixed part
Moving part
SPARE PART ASS'Y,
SPARE PART ASS'Y,
CONNECTOR KIT,TD160
BASE CONNECTOR,TD160
SPARE PART ASS'Y,
SPARE PART ASS'Y,
CONNECTOR KIT,TS250
BASE CONNECTOR,TS250
SPARE PART ASS'Y,
SPARE PART ASS'Y,
CONNECTOR KIT,TS400/630
SPARE PART ASS'Y,
SPARE PART ASS'Y,
CONNECTOR KIT,TS800
TD160
Moving part
Fixed part
T Phase
2AX
R Phase
AL
SUT or UVT
Lead wire
Connector base
Insert lead wire

to base groove
TS250
Moving part
T Phase
AX
Lead wire
Fixed part
R Phase
AX
AL
SUT or UVT
Insert lead wire

to base groove
Connector base
A-3-32

Connector KIT
TS400/630
Moving part
Fixed part
T Phase
AL
R Phase
3AX
SUT or UVT
Insert lead wire

to base groove
Lead wire
Connector
base
TS800
Moving part
Fixed part
T Phase
2AL
R Phase
3AX
SUT or UVT
Insert lead wire

to base groove
Lead wire
Connector
base
Read wire color

Moving part
Fixed part
Lead wire color

B: White
C: Red
E: Yellow
F: Blue
G: Brown
H: Orange
I: Gray
Note) Useless lead wires should be ended for

Preventing an electric occident.
- To connent AL and FAL solder the wire
and insulates the wire
Lead wire color
A-3-33
A: Black
D: Green
A: Black
B: White
C: Red
D: Green
E: Yellow
F: Blue
G: Brown
H: Orange
I: Gray
Note) Useless lead wires should be ended for

Preventing an electric occident.
AL, FAL
Accessory KIT

Remote operation
Motor operator
Motor operators can also be operated by manual.The motor drives a mechanism which switches
TD & TS toggle handle to the ON and OFF/RESET positions.
- The manual actuator handle is located on the front of the cover.
- Manual or Automatic operation can be selected.
The motor operator is an essential device for constructing a remote operated automatic sourcechangeover system to ensure a continuous supply of electrical power at following certain
installations:
- Commercial sector: Hospital, Tall building, Bank, Insurance companies, Shopping centers
- Industry: Ships, Assembly lines at plant, Military sites, Port and Railway installation
MCCB
Type
Control voltage
TS250 + MOP2
Actuation
Response time
current
(ms)
(A)
DC 24V
TD100, TD160
MOP1 AC 100~240V/
Closing Opening
Consumption
(W)
Mechanical
No. of
service life operations

(operations)
per hour
2.5A
(DC 24V)
310
200
14
25,000
120
350
230
14
25,000
120
500
350
35
20,000
60
700
420
35
10,000
20
DC 100~220V 0.5A (AC)

TS100, TS160,
TS250
MOP2 DC 24V
AC 100~110V/
TS400,TS 630
MOP3
DC 110V
AC 230/
TS800
MOP4
DC 220V
5A
(DC 24V)
2A
(AC)
Wiring connection
Standard connection
Circuit breaker On and Off controlled by remote operation and manual operation
P1
P2
S1
Power
Ue
S2
S4
1. 2Nm
ON
OFF
Connection with alarm switch (AL)

1) The below connection diagram is the method of using a alarm switch (AL) without shunt or
undervoltage trip.
2) After clearing the fault surely, manual reset is mandatory in case of tripping due to an electrical
fault.
Connection with FAL (only for the breakers with electronic trip unit ETS or ETM)
1) The below connection diagram is the method of using a FAL for circuit breakers with electronic
trip unit.
fault.
P1
P2
S1
S2
S4
ALb
Power
Ue
ALa
ALc
ON OFF
A-3-34

Remote operation
Manual operation
1) Insert the manual handle into the slot of Motor Operator surface and rotate it clockwise.
2) It must be rotated just 180 clockwise for safe operation of micro switch in the motor operator.
3) Return the manual handle after the manual operation
4) Turn the slide switch back to the position of AUTO.
CAUTION: When the circuit breaker is tripped by trip button in the OFF status,
it is impossible to operate motor operator automatically It must be reset by manual operation.
Manual handle
Automatic operation
1) Set the slide switch to AUTO, then internal power is closed automatically.
2) Operating frequency should be less than these below regulated values.
TD 160N/H/L, TS250N/H/L:180 operations per hour
3) Use the ON/OFF switch in the range of regulated values.
4) It may interfere near communication equipments because of internal switching power supply.
Its recommended that a noise filter be installed to power supply.
5) Please do not input ON/OFF signals at the same time during the automatic operation.
6) If the circuit breaker has a UVT attached inside, charge a UVT on the rated voltage before
performing MOTOR OPERATOR.
[TD100, 160, TS100, 160, 250]
A-3-35
[TS400, 630, 800]

Remote operation
Motor operator
Feature
On position indication (Red color)
Trip position indication (White color)
Off position indication (Green color)
Button for push to trip
(available for only for TD160AF and TS630AF)
On/Off/Reset selection lever
Manual/Auto selection lever
TD160 .... MOP-1
TS250 .... MOP-2
TS630.... MOP-3
TS800 .... MOP-4
A-3-36

The Susol circuit breaker can offer protection against earth leakage currents by using an add-on
residual current device (RCD). In particular, the TS100, TS160 and TS250 circuit breakers can be
combined with the RTU23 of residual current device, the TS400 and TS600 circuit breakers can be
combined with the RTU33 of residual current device and the TS800 circuit breaker can be
combined with the RTU43 of residual current device. In all cases the RCD unit interfaces directly
below the circuit breaker trip unit area without the use of any secondary wiring or connections.
The Susol circuit breaker and an RCD unit combination can be connected like any stand-alone
breaker and are available as fixed or plug-in devices. The main connection interface of the RCD is
an exact replacement of the breaker connection area, thus allowing the use of all standard breaker
terminals.
Overview
Apart from the protection against overloads typical of automatic circuit breakers, the residual
current circuit breaker derived from them also guarantee protection of people against earth leakage
currents, thereby ensuring protection against direct contacts, indirect contacts and fire hazards.(ELCB)
The RCD unit has numerous current and time settings and an override blocking the time settings
when set to 30mA. The earth leakage test button tests the electrical and mechanical operation of
the device. In order to allow for a dielectric test of the breaker and RCD combination without
damaging the electronics, the dielectric plug is placed within the setting area. The RCD unit may be
equipped with an alarm switch (FAL) to remotely indicate tripping due to an earth leakage current.
Compliance with standards :
- IEC 60947-2 (industrial), Appendix B
- IEC 61009 ( residential)
- IEC 60755, class A, immunity to DC components up to 6mA
- VDE664, operation down to -25C
Remote indications :
RCD unit may be equipped with an alarm contact (FAL-fault alarm switch) to remotely indicate
tripping due to an earth leakage current.
Power supply :
RCD unit are self-supplied internally by the distribution-system voltage and therefore do not require
any external source. They continue to function even when supplied by only two phases.
A-3-37

Configuration
Intermediate terminal shield
Sealable fixing screw for the intermediate

terminal
Dielectric plug(1)
Test push-button
Reset push-button
Sealable fixing screw for
Trip time delay settings(2)
Sensitivity settings
Slot for FAL auxiliary switch
(optional)
Sealing point for plate blocking access
to the settings
Rating plate
- Lift this plug before the dielectric test
- If the sensitivity is set to 30 mA, there is no time delay.
Whatever the time-delay setting.
Detail of Rating plate

Type of RCD
Applicable circuit breaker
Operational voltage and frequency
Compliance with standards
Standardized symbols :
- Class A immunity to DC components
(6mA insensitivity)
- Minimum operating temperature as per VDE664
Schematic diagram
A-3-38

Ratings and Selection
RCD type
Number of poles
Applicable
circuit breaker
RTU23
RTU33
RTU43
3*
3*
3*
TS100
TS160
TS250
TS400
TS630
TS800
Protection characteristics
Sensitivity
In(A)
(adjustable)
(adjustable)
(adjustable)
0.03-0.3-1-3-10
0.03-0.3-1-3-10
0.03-0.3-1-3-10
Intentional time
(adjustable)
(adjustable)
(adjustable)
delay(ms)
0-60-150-300-600
0-60-150-300-600
0-60-150-300-600
Time delay **
Rated voltage
Max. breaking
(adjustable)
(adjustable)
(adjustable)
time(ms)
40-140-240-450-880
40-140-240-450-880
40-140-240-450-880
AC 50/60 Hz
220~460V / 460~690V
220~460V / 460~690V
220~460V / 460~690V
* 3P modules may also be used on 2P circuit breakers.

** If the sensitivity is set to 30mA, the time delay setting is reduced to zero.
Trip time delay settings

0-60-150-300-600ms
Sensitivity settings, In
0.03-0.3-1-3-10A
A-3-39

Combination
The addition of the RCD unit does not affect circuit breaker characteristics.
- Conformity with standards
- Protection degrees, class II insulation front face
- Suitability for isolation as defined by IEC 60947-2
- Electrical characteristics
- Trip unit characteristics
- Installation and connection methods
- Indication, measurement and control accessories
- Installation and connection accessories
RTU23
MCCB
MCCB+RCD
LHD(mm)
RCD
MCCB+RCD
RTU33
RTU43
10516086
140260110
210320135
10524086
140370110
210450135
1058086
140110110
210130135
2.7
8.08
16.28
2.52
4.6
Weight(kg)
RCD
Type
Accessory
0.96
Bottom
FAL(fault alarm switch)
A-3-40

The following accessories for mounting, connection, insulation, handle operation are standard
items and are packed with Susol TD & TS series circuit breakers.
TD100N/H/L
TD160N/H/L
B-23C
M820
M375(1P)
M475
1P: 2pcs
3P: 6pcs
4P: 8pcs
1P: 2pcs
3P: 2pcs
4P: 4pcs
3P: 4pcs
4P: 6pcs
TS100N/H/L
TS160N/H/L
TS250N/H/L
B-23C
M820
3P: 6pcs
4P: 8pcs
M475
3P: 2pcs
4P: 4pcs
3P: 4pcs
4P: 6pcs
TS400N/H/L
TS630N/H/L
B-33C
M1030
3P: 6pcs
4P: 8pcs
M585
3P: 4pcs
4P: 4pcs
M5
3P: 4pcs
4P: 4pcs
3P: 4pcs
4P: 6pcs
TS800N/H/L
B-4
M1235
3P: 6pcs
4P: 8pcs
A-3-41
M6100
3P: 4pcs
4P: 4pcs
3C
M6
3P: 4pcs
4P: 4pcs
3P: 4pcs
4P: 6pcs
1pc
Accessories for TS series up to 1600A

TS 1000 to 1600AF Electrical and
mechanical accessories
MCCB
Barrier for front connection
Barrier for extension terminal
Terminal cover
Barrier for rear connection

Barrier aux for rear connection
Plate protection
Busbar
Lug terminal
Vertical busbar
Extension busbar
Rear connection
Auxiliary handle
Removable padlock (PL)
Fixed padlock (PHL)

Mechanical interlock (MIT)
Electrical auxiliary

Test kit
Voltage module
UVT time delay controller (UDC)
A-3-42

The following devices are installed into TS1000 to 1600AF circuit breakers regardless of frame
size. And, the electrical auxiliaries can be easily installed in the accessory compartment of the
circuit breakers which is cassette type.
AX1
AX2
AX3
AL
SHT/UVT
FUAL

Auxiliary switch is for applications requiring remote ON and OFF indication.
One is open and the other closed when the circuit breaker is open, and vice-versa.
AX
AL
Alarm switch (AL)

Alarm switches indicate that the circuit breaker has tripped due to overload, short circuit, shunt trip,
or undervoltage release conditions. They are particularly useful in automated plants where
operators must be signaled about changes in the electrical distribution system.
This switch features a closed contact when the circuit breaker is tripped automatically. In other
words, this switch does not function when the breaker is operated manually.
Contact operation
MCCB
Position
ON
OFF
TRIP
AXa1
AXa1
AXc1
of AX
AXc1
AXb1
AXb1
Position
of
AL
A-3-43
AXa1
AXa1
AXc1
AXc1
AXb1
AXb1

Indication switch FUAL

FUAL Indicates that the breaker has tripped due to FAL(overload, short circuit) and UAL(UVT,
SHT) separately
af
FAL
c
Normal position
UAL
a
b
a
b
au
CB no trip
fuc
FAL Normal Open / UAL Normal Open

FUAL
af
FAL
FAL operation
a
b
a
b
au
CB trip due to OCR

fuc
FAL Normal Close / UAL Normal Open

af
FAL
UAL operation
CB trip due to UVT

or SHT
UAL
a
b
a
b
au
fuc
FAL Normal Close / UAL Normal Close
FUAL
af
FAL
a
c
b
UAL
a
c
b
au
Rya 1
Rya 2 Rya 2
fuc
AC or DC
Power
Ry
UAL
signal
Lamp
FAL Lamp
signal
Figure. Example of Lock up Circuit for FUAL
Caution: Please use Lock up Circuit following under figure Example of lock up circuit for
FUAL
Caution: When MCCB is tripped by SHT or UVT, the FAL signal appears for 20ms that is time
of being transferred from bcontact to a contact of control relay
Caution: When MCCB is tripped by SHT or UVT, the transfer time of Relay signal(Ryb2 off
Rya2 on) is 20ms. if FAL signal is connected with other sequence circuit such as
Latch circuit or other look up circuit it may cause to be miss operation. So, please do
not use latch circuit or look up circuit with FAL signal.
A-3-44

SHT Shunt trip device

SHT is a control device which trips a circuit breaker from remote place, when applying voltage
continuously or instantaneously over 200ms to coil terminals(C1, C2).
When UVT coil is installed, its location is changed.
1. Rated voltage and characteristics of Trip coil

Rated voltage [Vn]
DC [V]
AC [V]
Power consumption (VA or W)

Operating voltage range [V]
24~30
0.6~1.1 Vn
48~60
48
0.6~1.1 Vn
100~130
100~130
0.56~1.1 Vn
200~250
200~250
0.56~1.1 Vn
380~480
0.56~1.1 Vn
Inrush
Steady-state
Trip time [ms]
Less
200
than
40ms
Note) Operating voltage range is the min. rated voltage standard for each rated voltage(Vn).
Opening
order
2. Specification of the wire

- Refer to the below table regarding the length and specification of wire when using trip coil with DC
24~30[V] or DC/AC 48~60[V] of rated voltage.
C1
The maximum wire length

SHT
Rated voltage [Vn]

DC 24~30 [V]
C2
Wire type
*
The dotted
to
Userline
be made by the
Wiring Diagram
customer
Wiring Diagram
A-3-45
Operating
voltage
DC/AC 48 [V]
#14 AWG
#16 AWG
#14 AWG
#16 AWG
(2.08mm )
(1.31mm )
(2.08mm )
(1.31mm2)
100%
95.7m
61m
457.8m
287.7m
85%
62.5m
38.4m
291.7m
183.2m

UVT Under Voltage Trip device

- If the voltage of the main or the control power is under voltage, UVT which is installed inside of
the breaker breaks the circuit automatically. Please connect with UVT time-delay device in order
to present the time delay function because UVT is technically instantaneous type.
- The closing of a circuit breaker is impossible mechanically or electrically if control power not
supplied to UVT. To close the circuit breaker, 65~85% ofrated voltage should be applied to both
terminals of UVT coil (D1, D2).
- When using UVT coil, the double trip coil can not be used, and the location of trip coil is changed.
1. Rated voltage and characteristics of UVT coil

Rated voltage [Vn]
DC [V]
AC [V]
24~30
48~60
48
100~130
100~130
200~250
200~250
380~480

Pick up
Drop out
Inrush
Steady-state
Trip time [ms]
Less
0.65~0.85 Vn
0.44~0.6 Vn
200
than
50ms
Note) Operating voltage range is the min. rated standard for each rated voltage (Vh).
Opening
order
2. Specification of the wire

- Refer to the below table regarding the length and specification of wire when using trip coil with DC
24~30[V] or DC/AC 48~60[V] of rated voltage.
D1
The maximum wire length

UVT
Rated voltage [Vn]

DC 24~30 [V]
D2
#16 AWG
#14 AWG
#16 AWG
(2.08mm )
(1.31mm )
(2.08mm )
(1.31mm2)
100%
48.5m
30.5m
233.2m
143.9m
85%
13.4m
8.8m
62.5m
39.3m
Wire type
*
The dotted
to
Userline
be made by the
Wiring Diagram
customer
Wiring Diagram
Operating
voltage
DC/AC 48 [V]
#14 AWG
2
Note) In case of using UVT coil, the location of TC coil is changed.
A-3-46

OCR Tester [OT]
- It is a device which can test for the

operation of Trip Relay under no power
condition.
1. Maximum 17 times rated current
can be inputted.
2. It is possible to enter the current value
and phase on each of R/S/T/N
3. Frequency is adjustable.
4. It is available to test for long time
delay/short time delay/instantaneous
/ground fault.
OCR tester
Configuration
R
R, S, T, N phase signal input
Increase/Decrease signal input
ENT.
ESC
START
STOP
Signal setting/Delete
Waveform generation/Stop
50Hz 60Hz
Hz
A-3-47
Select frequency

UVT Time Delay Controller [UDC]
- UVT is a device which makes ACB tripped automatically to prevent the accident on load side due
to under voltage or power breakdown.
There are two types, Instantaneous type and time delay type.
- It can be installed on the rail or to the cradle.
- Instantaneous type: only available with UVT coil.
- Time delay type: available by connecting UVT coil and UVT time delay controller.
- Common use for the all types.
1. The rated voltage and characteristic of UVT time delay controller
Rated voltage [Vn]
DC [V]
AC [V]
48~60
48
100~130
100~130
200~250
200~250
380~480
Pick up
Drop out
Inrush
Steady-state
0.65~0.85 Vn
0.44~0.65Vn
200
Trip time[s]
0.5, 1,
1.5, 3
Note) Operating voltage range is the min. rated standard for each rated voltage (Vh).
2. Wiring
1. Wiring for general type
2. Wiring for special type
Rated
voltage
(Vn)
Rated
voltage
(Vn)
Delay trip
function
14
16
14
16
D2
Instantaneous
trip
function
D1
D2
D1
ACB
ACB
Rated
voltage
(Vn)
Rated
voltage
(Vn)
* The wiring presented with red color should be set by users.
A-3-48

Rotary handle
in the open position. There are direct rotary handletwo and extended rotary handle.

Degree of protection IP40
There are three types of direct rotary handle according to line load direction.
Indication of the three positions O(OFF), I(ON) and tripped. Circuit breaker locking capability in the
OFF position by one to three padlocks, shackle diameter 5 to 6 mm (not supplied).
L Type
LINE
S Type
LOAD
LINE
R Type
LOAD
LINE
LOAD
Door cut type for Direct rotary handle

A Type
B Type
Dimension of door cut

A Type
B Type
380 (3P) Minimum
450 (4P) Minimum
205 (3P) Minimum

275 (4P) Minimum
205 Minimum
280 Minimum
4- 7
8.5
203
217
201
212
4- 7
25.5
t1.2~3.2
155.5
204.5
267
A-3-49
46
33
196
210
134
145
t1.2~3.2
204.5
267
Note) 1. In case of disassembling and assembling the main cover, screw should be tightened in specific torque of1.5N.m (15.3kgf.cm)
2. In case of disassembling and assembling the main cover by over tightening torque, the parts of MCCB can be damaged.

Rotary handle
Locking system(Door lock)

To open the panel door at ON position, just rotate release screw counterclockwise.
When MCCB is on position, panel door is can't be open.
Release
lever
Please open the

door after rotating
release lever
Door locking
OFF State
ON State
Caution
- If the door is opened with much pressure when
the position of handle is ON or TRIP, the handle
lock lever will be damaged
Key lock
After locking handle, be sure that the key removed.
A locking can be done by using the rotary handle which has key
lock device.
The lock is used to lock the circuit-breaker in the OFF position.
Key lock: locking OFF position
5~6
Padlocking by rotary handle

A padlocking can be also done by using the rotary handle.
The lock is used to lock the circuit-breaker in the ON and OFF
position.
Maximum three (3) padlocks with shackle diameters ranging from
5 to 6mm may be used. (Padlocks are not supplied)
Locking at ON or OFF position
A-3-50

Rotary handle

Degree of protections IP55
There are three types of extended rotary handle according to line & load direction
With Extended rotary handles, can be operate MCCB at the back of switchboards, from the
switchboard front.
Indication of the three positions O(OFF), I(ON) and tripped circuit breaker locking capability in the
OFF position by one to three padlocks, shackle diameter 5 to 6mm (not supplied).
When MCCB is on position, panel door is can't be open.
L Type
S Type
Shaft
R Type
Handle
Dimension of door cut
78
t1.2~3.2
246
681 Maximum (SHAFT Max. 469)
A-3-51
108
4- 6
24
108

Rotary handle
Locking system(Door lock)

To open the panel door at ON position, just rotate release screw clockwise.
When MCCB is on position, panel door is can't be open
Please open the

door after rotating
release lever
Open OK
Release
lever
OFF State
Door locking
Locking at ON or
OFF position
ON State
Caution
- If the door is opened with much pressure when
the position of handle is ON or TRIP, the handle
lock lever will be damaged
Type
IP
IP40
Totally protected
rotary extended handle
against ingress of
dust and water jets from any
IP65
direction
A-3-52

Locking devices
Removable padlock(PL)
This device allows the handle to be locked in the OFF position.
The locking device for the toggle handle can be installed in 3-pole and 4-pole
circuit-breakers. Maximum three (3) padlocks with shackle diameters ranging from 5
to 8mm may be used. (Padlocks are not supplied)
Cover
PAD LOCK
Fixed padlock (PHL)

This device allows the handle to be locked in the ON and OFF position.
The locking device for the toggle handle can be installed in 3-pole and 4-pole circuitbreakers.
Maximum three (3) padlocks with shackle diameters ranging from 5 to 8mm
may be used. (Padlocks are not supplied)
A-3-53

Locking devices
Mechanical interlock (MIT)

This mechanical interlocking device is very useful and simple for consisting of manual source
changeover system
A-3-54

Terminal
Front connection of Fixed devices

Bars
Fixed, front-connection Susol TS1600AF devices are equipped with terminals comprising
captive screws for direct connection of bars.
Other connection possibilities for bars include vertical-connection adapters for edgewise bars and
spreaders to increase the pole pitch to 95 mm.
Vertical busbar
Busbars
Bare cables
Lug terminals may be used to connect four 85 up to 240 copper or aluminum cables for each
phases. Bare cable connection is possible for rating up to and including 1250A
Lug terminal
L(mm)
S() Cu/Al
Torque(kgfcm)
A-3-55
25~55
485 to 4240
564

Terminal
Crimped Terminals
Crimped terminals are combined with the vertical and extension busbars.
One to four cables with crimped terminals(300 ) may be connected.
To ensure stability, connectors must be fixed and insulated between the terminal extensions.
Vertical busbar
Extension busbars
A-3-56

Terminal
Rear connection of Fixed devices

Bars
Rear connection devices equipped with horizontal or vertical connectors may be directly connected
to flat or edgewise busbars, depending on the position of the connectors.
Busbars are available to increase the pole pitch to 95mm
The standard type of rear connection type is horizontal type.
If customer want to conect busbars with vertical or comvination(horizontal and vertical)
please order separately.
Busbars
Vertical busbar
Crimped Terminals
Crimped terminals enable connection of one to four cables with crimped terminals(300 )
To ensure stability, connectors must be fixed and insulated between the terminal extensions
Extension busbars
A-3-57

Insulation
Terminal cover
Mounted on fixed, front-connection devices,
it insulates power-connection points.
Barrier
These barriers are insulated between the phases for increase insulation level.
It also can be easily mounted, even the circuit-breaker already installed, inserting them in
It is possible to mount the phase separating partitions between two circuit-breakers side
Barrier for front connection

paking unit: 2ea/3Pole, 3EA/4Pole
Barrier for extension terminal

paking unit: 2ea/3Pole, 3EA/4Pole
Plate protection
paking unit: 1ea/3Pole, 1ea/4Pole
3Pole
4Pole
A-3-58

The following accessories for mounting, connection, insulation, handle operation are standard
items and are packed with Susol TD & TS series circuit breakers.
Barrier Interphase
3P: 2ea, 4P: 3ea
Circuit breaker: 1ea
Nut(M5): 4ea
Nut(M10), S/W, P/W
3P: 12, 4P: 16
Handle Aux: 1ea
Plate protection: 1ea
Screw (M5110): 4ea
Components

A-3-59
Handle
Test Button
Moving Contactor
Load Terminal
Contact Spring
Arc Chute
Main Spring
Link Assy
Power CT
Handle Cover
Terminal Bolt
Moving Tip
Main Shaft Assy

Hard Trip Device
Main Cover
Wall Holder Contactor
Fixed Tip
A-4. Mounting & Connection

Fixed mounting
A-4-1
Connecting terminal & conductor
A-4-2
Safety clearance
A-4-3
Example of installation
A-4-6
Connections for 1600AF
A-4-7
Size of busbar for 1600AF
A-4-8
Mounting & Connection

Fixed mounting
Susol TD and TS circuit-breakers can be directly connected to the mounting plate.

If busbars or terminals are used to connect the circuit breaker
on the back of the mounting plate,
the appropriate safety clearances must be observed.
TD100, TD160
TS100,TS160,
TS250
TS400, TS630
TS800
Screw for
mounting
1Pole:2EA(M375)
3Pole:2EA(M475) 3Pole:2EA(M475) 3Pole:4EA(M585) 3Pole:4EA(M6100)
Nut for
mounting
3Pole:4EA
3Pole:4EA
4Pole:4EA
4Pole:4EA
Screw for
connection
of terminals,
Spreader
1Pole:2EA(M820)
Torque:
Max 78kgfcm
A-4-1
Torque:
Max 147kgfcm
Torque:
Max 490kgfcm
Torque:
Max 630kgfcm

Connecting terminal & conductor
Terminal (mm)
Conductor (mm)
TD100
8
18
TD160
23
M820
22
Max 78kgfcm
TS100
20
TS160
TS250
28
>8
>8
M820
21
10
10
22
25
25
Max 147kgfcm
TS400
30
M10L30
15
TS630
26.1
Max 490kgfcm
TS800
33
16.5
M1235
12
12
3745
15 3745 19
51
26
=
50
=
50
=
50
Max 630kgfcm
A-4-2

Safety clearance
When installing a circuit breaker, safety clearances must be kept between the breaker and panels,
bars and other protection devices installed nearby. These safety clearances are depend on the
ultimate breaking capacity and are defined by tests carried out in accordance with standard IEC
60947-2.
When a short circuit interruption occur, high temperatures pressures are present in and above the
arc chambers of the circuit-breaker. In order to allow the pressure to be distributed and to prevent
fire and arcing or short-circuit currents, safety clearances are required.
A: Insulation distance to ceiling for installation in metallic cubicle

A(mm)
35
30
TD100H, TD160H
35
30
TD100L, TD160L
35
30
TS100N, TS160N, TS250N
35
30
TS100H, TS160H, TS250H
35
30
TS100L, TS160L, TS250L
35
30
TS400N, TS630N
60
50
TS400H, TS630H
60
50
TS400L, TS630L
60
50
TS800N
100
80
TS800H
100
80
TS800L
100
80
TD100N, TD160N
240V
415V
C1: Minimum distance for superimposed circuit breakers

(from lower circuit breaker to uninsulated part of terminal of upper circuit breaker)
C: C1+ the dimension of exposed conducting part (The dimension of exposed conduct)
A-4-3
35
30
TS 100N, TS160N, TS250N
35
30
35
30
35
30
TS400N, TS630N
60
50
TS400H, TS630H
60
50
TS400L, TS630L
60
50
TS800N
100
80
TS800H
100
80
TS800L
100
80
Direct
connection
of cable
TD100L, TD160L
Connection by
using a cable
terminal or
ring
terminal
C1
30
30
35
C1
35
TD100H, TD160H
TD100N, TD160N
C(mm)
C1
240V
The dimension of exposed conduct
C1(mm)
415V
Connection
by using a
cable
terminal with
extended
terminal

Safety clearance
D: Insulated length of main terminal of circuit breaker

TS400N, TS630N
TS400H, TS630H
TS400L, TS630L
TS800N
TS800H
TS800L
50
50
50
50
100
100
100
200
200
200
200
200
200
50
50
100
100
100
200
D4
D4
(mm)
D3
D2
TD100L, TD160L
D3
(mm)
D1
TD100H, TD160H
D2
(mm)
The dimension of exposed conduct + 20
TD100N, TD160N
D1
(mm)
The dimension of exposed conduct + 20
D1: Connection by ring terminal after taping

(Larger than the dimension of exposed conducting part)
D2: Connection by bar after taping
D3: Connection by ring terminal using insulation barrier
(Larger than the dimension of exposed conduct
D4: Connection by bar using insulation barrier
200
200
200
200
200
Note) If uninsulated conductors are used for connection, please insulate by taping to
the point where the conductors overlap with the insulation barrier or to the root of the circuit breaker.
E: Distance from a side of breaker to side plate

E(mm)
415V
240V
TD100N, TD160N
25
15
TD100H, TD160H
25
15
TD100L, TD160L
25
15
25
15
25
15
25
15
TS400N, TS630N
20
15
TS400H, TS630H
20
15
TS400L, TS630L
20
15
TS800N
45
20
TS800H
45
20
TS800L
45
20
A-4-4

Safety clearance
F: The dimension of exposed conducting part

F
TD100N, TD160N
20
TD100H, TD160H
20
TD100L, TD160L
20
10
10
10
TS400N, TS630N
10
TS400H, TS630H
10
TS400L, TS630L
10
TS800N
10
TS800H
10
TS800L
10
(mm)
G: Minimum center distance for two horizontally installed circuit-breakers

G
(mm)
TD100N, TD160N
TD100H, TD160H
TD100L, TD160L
TS400N, TS630N
TS400H, TS630H
TS400L, TS630L
TS800N
TS800H
TS800L
Note) In case of using long or short terminal covers.
A-4-5

Example of installation
TD100/160
TS100/160/250
M475
35
35
25
2
90
90
35
TS400/630
60
M575
20
90
90
60
TS800
100
M6100
45
90
90
100
Note) In case of using long or short terminal covers,

no need to consider on minimum center distance for two horizontally installed circuit-breakers
A-4-6

Connections for 1600AF
The quality of busbar connections depends, among other things, on the tightening torques used for
nuts and bolts. Over-tightening may have the same consequences as under-tightening.
The correct tightening torques for the connection of busbars to the circuit breaker terminals are
indicated in the table below.
Examples of busbar connections

Susol TS1600 MCCB may be installed vertically, horizontally or flat on their back.
Front type
Front type with bars (on backplate or rail)
MAX. 2W50t10
MAX. 2W50t8, INTER BUS MAX. 5t
Front type with basbar (only on rail)
example) 3W80t5
example) 3W80t5
example) 2W60t10
Rear type with bars (only on backplate)
example) 3W80t5
example) 2W60t10
example) 2W50t10
example) 3W80t5
Insulation distance
Examples
Tightening torques for busbar
Bolt
M10
Drilling diameter
Tightening torque
(mm)
(kgfcm)
11
240~500
Insulation distance
Dimension(mm)
X
A-4-7
Utillsation voltage
X minimum
Ui600V
8mm
Ui1000V
14mm

Size of busbar for 1600AF
The following tables are based on the following assumptions;

- Maximum permissible temperature of busbars are 100C
- T : Temperature around the circuit breaker and its connections
Note) 1. The values presented in the tables are the result of trials and theoretical calculations on the basis of the assumption mentioned above.
2. These tables are intended as an aid in designing connection, however, the actual values must be confirmed by tests on the installation.
Insulation barrier and plate protection on line side is standard.

If customer want to using insulation accessories on load side, please oder separately.
Front and horizontal rear connection

Model
TS1000
TS1250
TS1600
Maximum
current
T:40C
Number of busbars
t=5mm
t=10mm
T:50C
T:60C
Number of busbars
Number of busbars
t=5mm
t=10mm
t=5mm
t=10mm
800
2b.5t50
1b.10t50
2b.5t50
1b.10t50
2b.5t50
1b.10t60
1000
3b.5t50
1b.10t60
3b.5t50
2b.10t50
3b.5t60
2b.10t50
2b.10t50
3b.5t60
2b.10t50
3b.5t50
2b.10t40
3b.5t50
2b.5t80
2b.10t40
2b.5t80
1400
2b.5t80
2b.10t40
2b.5t80
2b.10t50
3b.5t80
2b.10t60
1600
3b.5t80
2b.10t60
3b.5t80
2b.10t60
3b.5t80
3b.10t50
1250
Vertical rear connection

Model
TS1000
TS1250
TS1600
Maximum
current
T:40C
Number of busbars
T:50C
T:60C
Number of busbars
Number of busbars
t=5mm
t=10mm
t=5mm
t=10mm
t=5mm
t=10mm
800
2b.5t50
1b.10t50
2b.5t50
1b.10t50
2b.5t50
1b.10t50
1000
2b.5t50
1b.10t50
2b.5t50
1b.10t50
2b.5t60
1b.10t60
1250
2b.5t60
1b.10t60
3b.5t50
2b.10t40
3b.5t50
2b.10t40
1400
2b.5t80
1b.10t80
2b.5t80
2b.10t50
3b.5t60
2b.10t50
1600
3b.5t60
2b.10t50
3b.5t60
2b.10t50
3b.5t80
2b.10t60
A-4-8
A-5. Characteristics curves

Susol MCCB up to 800AF
Thermal-magnetic trip units (TE100, TE160)
Thermal-magnetic trip units (TD100, TD160, TS100)
Magnetic only trip units (TS100, TS160)
Thermal-magnetic trip units (TS160, TS250)
Magnetic only trip units (TS250)
Thermal-magnetic trip units (TS400)
Electronic trip unit (ETS)
Electronic trip unit (ETM)
A-5-1
A-5-3
A-5-6
A-5-7
A-5-11
A-5-12
A-5-14
A-5-15
A-5-17
A-5-18
A-5-20
A-5-21
A-5-21
Susol MCCB 1600AF

Long-time delay (L)
Instantaneous (I), Ground fault (G)
IDMTL
Pre Trip Alarm
A-5-23
A-5-24
A-5-25
A-5-26
A-5-27
Specific let-through energy curves
A-5-28
Current-limiting curves
A-5-31
Circuit breakers with thermal-magnetic trip units
TE100
FTU
FMU
16~100A
FTU:Ir=1In
FMU:Ir=0.8~1In
FTU/FMU:Im=10In
Min. 400A
A-5-1
In:16A -> Im=400A

In:20A -> Im=400A
In:25A -> Im=400A
In:32A -> Im=400A
In:40A -> Im=400A
TE160
FTU
FMU
100~160A
FTU:Ir=1In
FMU:Ir=0.8~1In
FTU/FMU:Im=10In
Min. 400A
A-5-2
TD100
FTU
FMU
16~100A
A-5-3
TD160
FTU
FMU
100~160A
A-5-4
TS100
FTU
FMU
40~100A
A-5-5
Circuit breakers with magnetic only trip units
TS100
Magnetic only
MTU
1.6~100A
TS160
Magnetic only
MTU
32~160A

Rating(A)
In
TS100 to TS800
1.6
3.2
6.3
12
20
32
50
63
100
N / H / L TS100
TS160
160
220
320
500
TS250
TS400
TS630
TS800
630

Pick - up
Im
Setting
6..12 In (6 Point)
A-5-6
TS160
FTU
FMU
100, 125, 160A
A-5-7
TS160
ATU
100, 125, 160A
A-5-8
TS250
FTU
FMU
125~250A
A-5-9
TS250
ATU
125~250A
A-5-10
TS250
Magnetic only
MTU
100, 160, 220A

Rating(A)
N/H/L
In
TS100 to TS800
1.6
3.2
6.3
12
20
TS160
63
100
TS250
TS400
TS630
TS800
Im
160
-
Setting
6..12
A-5-11
50
TS100

Pick - up
32
In (6 Point)
220
320
500
630
TS400
FTU
FMU
300, 400A
A-5-12
TS400
ATU
300, 400A
A-5-13
TS400
MTU
320A

Rating(A)
In
TS100 to TS800
1.6
3.2
6.3
12
20
32
50
63
100
N / H / L TS100
TS160
160
220
320
500
TS250
TS400
TS630
TS800
630

Pick - up
Im
Setting
6..12 In (6 Point)
A-5-14
TS630
FTU
FMU
500, 630A
A-5-15
TS630
ATU
500, 630A
A-5-16
TS630
MTU
500A

Rating(A)
N/H/L
In
TS100 to TS800
1.6
3.2
6.3
12
20
TS160
63
100
TS250
TS400
TS630
TS800
Im
160
-
Setting
6..12
A-5-17
50
TS100

Pick - up
32
In (6 Point)
220
320
500
630
TS800
FTU
700, 800A
FMU
800A
A-5-18
TS800
ATU
800A
A-5-19
TS800
MTU
630A

Rating(A)
In
TS100 to TS800
1.6
3.2
6.3
12
20
32
50
63
100
N / H / L TS100
TS160
160
220
320
500
TS250
TS400
TS630
TS800
630

Pick - up
Im
Setting
6..12 In (6 Point)
A-5-20
Circuit breakers with electronic trip unit (ETS)
TS100 to TS800
ETS23
ETS33
ETS43
A-5-21
Circuit breakers with electronic trip unit (ETM)
TS400
TS630
TS800
ETM33
ETM43
A-5-22
Long-time delay (L)
TS1600
5000
2000
Ir = 0.4...1 In
1000
500
200
100
50
40
30
tr = 0.5...20s
20
20
12
10
t(s)
5
4
3
4
2
1
1
0.5
0.4
0.3
0.2
0.1
0.05
Ir
A-5-23
20
10
0.7
0.01
0.5
0.02
5000
2000
1000
500
Isd = 1.5...10 Ir
200
100
50
40
30
20
10
t(s)
5
4
3
2
1
0.4
0.3
0.4
0.2
0.2
I2t ON
0.4
0.3
0.3
0.2
I2t OFF
0.1
0.1
0.1
0.05
0.05
20
10
0.01
0.7
0.02
0.5
TS1600
Ir
A-5-24
Instantaneous (I)
Ground fault (G)
TS1600
100
50
40
30
20
Ig = 0.2...1 In
10
5
4
3
2
t(s)
1
I2t ON
0.4
0.4
0.3
0.3
0.2
0.2
0.2
0.1
I2t OFF
0.1
0.1
0.4
0.3
0.05
0.05
Ii = 2...15 In
A-5-25
In
10
4
5
0.7
0.4
0.5
0.3
0.2
0.1
0.07
0.01
0.05
0.02
IDMTL
10000
5000
2000
EIT
1000
500
VIT
200
100
SIT
t(s)
50
20
DT
10
20
10
0.05
0.7
0.5
TS1600
Ir
A-5-26
Pre Trip Alarm
TS1600
500
200
100
50
40
35
30
20
15
10
5
5
4
3
t(s)
2
1
1
0.4
0.3
0.2
0.1
0.05
Ip
A-5-27
30
20
10
0.7
0.01
0.5
0.02
2
220/240V
Thermal stress
10
TS1600
TS1000
10
TS800
3
10
TS630
TS250
3
TD160
10
TE160
2
2
10
20
30
40
60
100
200
300
A-5-28
2
380/415V
Thermal stress
10
TS1600
5
TS1000
10
TS800
5
TS630
10
TS250
5
TD160
3
TE160
10 5
2
2
A-5-29
10
20
30
40
60
100
200
300
2
480/500V
Thermal stress
10
TS1600
5
TS1000
10
TS800
5
TS630
2
10
TS250
5
TD160
3
TE160
10
2
2
10
20
30
40
60
100
200
300
A-5-30
200
220/240V
Peak current
TS1000
100
80
70
TS800
60
50
TS630
40
30
TS250
20
TD160
TE160
10
8
7
6
A-5-31
10
20
30
40
60
100
200
300
200
380/415V
Peak current
TS1000
100
80
70
TS800
60
TS630
50
40
TS250
30
TD160
20
TE160
10
8
7
6
4
2
10
20
30
40
60
100
200
300
A-5-32
200
480/500V
Peak current
100
TS1000
80
70
TS800
60
50
TS630
40
30
TS250
TD160
20
TE160
10
8
7
4
2
A-5-33
10
20
30
40
60
100
200
300
A-6. Dimensions
Susol MCCB TE100, 160 series
TE100, 160
A-6-1
Susol MCCB TD, TS series up to 800A

TD160
TD100, 160
TS100, 160, 250
TS400, 630
TS800
A-6-2
A-6-3
A-6-4
A-6-5
A-6-6

Direct rotary handles up to 800AF
Extended rotary handles up to 800AF
Mechanical interlocking device up to 800AF
Plug-in device up to 800AF
Terminal cover up to 800AF
Rear terminals up to 800AF
Extended terminal up to 800AF
Rear terminals up to 800AF
Circuit breaker with motor operator up to 800AF
Wiring connection(motor operator)
Wiring diagram(State of operation)
A-6-7
A-6-13
A-6-19
A-6-22
A-6-28
A-6-30
A-6-30
A-6-31
A-6-37
A-6-38
A-6-39
Susol MCCB TS series up to 1600A

TS1000, 1250, 1600A front type
TS1000, 1250, 1600A front type busbar
TS1000, 1250, 1600A rear type
Rotary handles for TS 1600AF
Locking devices for TS 1600AF
Terminals for TS1600AF
A-6-40
A-6-41
A-6-42
A-6-43
A-6-44
A-6-45
Overall dimensions
TE100/160
[mm]
45
81
110
130
21.5
CL
70
82
89.5
CL
25
50
76
25
50
25
101
Min
2.5mm2
Max.
70mm2
Wire size
L
T W
L(mm)
17.5
W(mm)
13.5
T(mm)
Torque
8Nm
Panel drilling
25
25
CL
78
CL
47
83
CL
CL
CL
CL
110
CL
A-6-1
M4 OR 5
110
CL
Front panel cutting
47
83
103
Overall dimensions
TD160
[mm]
60
81
CL
22
140
122
107.5
86
27
14.5
28
35
77
81
86
92
106.9
1P
Conductor
10
18
20
M820
Terminal section
21.5
23
Panel drilling
Front panel cutting
M3 or 4
CL
83
107.5
CL
CL
CL
62
CL
CL
29
28
37
1P
1P
A-6-2
Overall dimensions
TD100/160
[mm]
50
75
Insulation barrier
B-23C
4.5
69
Mounting hole
27
60
C
L
81
C
L
22
140
122
109.6
107
14.5
52
Trip button
B-23C
77
81
86
92
106.9
60
90
30
60
120
2, 3P
Conductor
10
18
20
M820
Terminal section
4P
21.5
23
Panel drilling
Front panel cutting

M4 or 5
30
2, 3P
CL
CL
30
30
4P
CL
CL
CL
83
107
107
CL
A-6-3
CL
83
M4 or 5
CL
92
122
2, 3P
4P
Overall dimensions
TS100/160/250
[mm]
50
75
Insulation barrier
69
11
CL
Mounting hole
CL
CL
22
CL
60
Mounting hole
27
160
140
125
B-23C
Trip button
Trip button
B-23C
70
105
75
81
86
93
109.7
35
2, 3P
70
140
4P
4P R
Conductor
10
20
25
M820
Terminal section
35
70
140
21.5
28
Panel drilling
C
L
35
2,3P
M4 TAP or 5 Hole
C
L
35
CL
CL
CL
N
CL
CL
100
C
L
100
M4 TAP or 5 Hole
100
125
N
C
L
C
L
125
M4 TAP or 5 Hole
125
C
L
Front panel cutting
CL
107
142
142
2,3P
4P
4P R
35
70
70
4P
4P R
A-6-4
Overall dimensions
TS400/630
[mm]
53
46.5
93.5
53
41
25
53
53
53
Mounting hole
Mounting hole
CL
CL
CL
CL
31
34.5
260
230
202
200
166
260
27
71
6
10
53
53
13
116
75
44.1
8
53
46.5
26.5
Trip button
Trip button
27
30
45
46.5
59
140
97.5
105
110
123
157
46.5
186.5
46.5
46.5
46.5
186.5
4P
2,3P
Terminal section
30
46.5
46.5
4P R
Conductor
26.1
15
30
15
M5 L30
13
Panel drilling
46.5
2,3P
A-6-5
46.5
46.5
93
93
4P
4P R
CL
N
CL
CL
142
188.5
2,3P
4P
168
CL
168
200
CL
CL
M5 TAP or 6 Hole
CL
168
N
CL
M5 TAP or 6 Hole
CL
200
M5 TAP or 6 Hole
200
CL
Front panel cutting
CL
188.5
4P R
Overall dimensions
TS800
[mm]
89
42
10
70
70
70
70
70
70
70
Mounting hole
82.8
Mounting hole
CL
CL
CL
26.7
9 37.3
CL
320
287
278
254.6
198.6
35
Trip button
Trip button
49
70
80
210
119
128
135
148.5
198
2,3P
280
4P
4P R
Conductor
14
33
32
51
15.5
Panel drilling
278
C
L
70
2, 3P
C
L
M6 TAP or 7 Hole
C
L
C
L
70
70
4P
M6 TAP or 7 Hole
C
L
70
70
4P R
C
L
C
L
N
278
M6 TAP or 7 Hole
278
4P C
L
Front panel cutting
200.6
1235
50
16.5
Terminal section
280
C
L
212
2, 3P
200.6
320
33.3
7
13.4
115
81.5
37
8
16
70
C
L
282
4P
A-6-6
Overall dimensions
DH1E for TE100/160
[mm]
OFF
77.5
92.1
A-6-7
110
t 1.2~3.2
114.9
101.5
4-5
68.2
121
Overall dimensions
DH1 & DHK1 for TD100/160
[mm]
90
t1.2~3.2
81.3
71.8
13.5
60
77
117
81
Panel drilling
Way of installation
Over 20mm
84
96.3
Panel shaft
4-5
Trip
Trip
93
105
A-6-8
Overall dimensions
DH2 & DHK2 for TS100/160/250
[mm]
t=1.2~3.2
105
78.5
91.8
10.7
60
96
75
119
Panel drilling
Way of installation
Over 20mm
Trip
83
95
Panner shaft
4-5
Trip
108
121
A-6-9
Overall dimensions
DH3 & DHK3 for TS400/630
[mm]
t1.2~3.2
97.5
131
147.5
18.75
140
93
129
170.5
Panel drilling
Way of installation
Over 20mm
Trip
133
149
Panel shaft
4-7
Trip
143
159
A-6-10
Overall dimensions
DH4 & DHK4 for TS800
[mm]
t=1.2~3.2
210
119
211
192.5
Panel drilling
Way of installation
Over 20mm
Trip
MCCB
162
173
Panner shaft
4-7
Trip
213
225
A-6-11
186.6
165.4
23
140
Overall dimensions
Dimension table for D-handles
TD100/TS250
[mm]
TS630/TS800
t1.2~3.2
D
E
B
C
B
C
D
E
A
F
Applicable to
TD160
TS250
TS630
TS800
A (mm)
117
119
170.5
211
B (mm)
71.8
78.5
131
165.4
C (mm)
81.3
91.8
147.5
186.6
D (mm)
90
105
140
210
E (mm)
60
60
93
140
F (mm)
81
96
129
192.5
A-6-12
Overall dimensions
EH1E for TE100/160
[mm]
OFF
t 1.2~3.2
min 165
max 589(shaft 459mm)
2-6
47
53
47
A-6-13
Overall dimensions
EH1 for TD100/160
[mm]
90
t1.2~3.2
Min. 163
Max. 585 (Shaft 469mm)
81.3
71.8
13.5
60
81
Panel drilling
Way of installation
2-6
53
47
OFF
OFF
47
A-6-14
Overall dimensions
EH2 for TS100/160/250
[mm]
t=1.2~3.2
78.5
91.8
10.7
105
60
96
Min. 163
Panel drilling
Way of installation
2-6
53
47
OFF
OFF
47
A-6-15
Overall dimensions
EH3 for TS400/630
[mm]
t1.2~3.2
131
147.5
18.75
140
93
Min. 228
129
Panel drilling
Way of installation
4-6
OFF
108
78
OFF
108
A-6-16
Overall dimensions
EH4 for TS800
[mm]
t=1.2~3.2
165.4
186.6
23
210
140
Min. 275
192.5
Panel drilling
Way of installation
4-6
108
78
108
A-6-17
OFF
OFF
Overall dimensions
Dimension table for E-handles
F
C
F
C
[mm]
B
E
TS630/TS800
B
E
t1.2~3.2
TD100/TS250
D
A
D
Model
Applicable to
A (mm)
EH1
EH2
EH3
EH4
TD160
TS250
TS630
TS800
Min. 163
Min. 163
Min. 228
Min. 275
Max. 585
Max. 585
Max. 645
Max. 687
B (mm)
71.8
78.5
131
165.4
C (mm)
60
60
93
140
D (mm)
81
96
129
192.5
E (mm)
81.3
91.8
147.5
186.6
F (mm)
90
105
140
210
Shaft (mm)
469
469
469
469
A-6-18
Overall dimensions
MIT13E, MIT14E for TE100/160
[mm]
82
47
4~6
30mm
83
70
A-6-19
Overall dimensions
MIT13, MIT23, MIT33, MIT43
[mm]
A (mm)
B (mm)
TD160
83
86
TS250
102
86
TS630
168
110
TS800
201
135
Dimension of lock
5~8mm
30mm
A-6-20
Overall dimensions
Mounting dimension for MIT
[mm]
A-6-21
2, 3Pole MCCBs
C(mm)
D(mm)
E(mm)
4Pole MCCBs
C(mm)
D(mm)
E(mm)
TD100/160
107
90
30
TD100/160
107
90
60
TS100/160/250
125
105
35
TS100/160/250
125
105
70
TS400/630
200
139.5
46.5
TS400/630
200
139.5
93
TS800
278
210
70
TS800
278
210
140
Overall dimensions
Plug-in device
Plug-in devices for TD100/160
[mm]
A
F
G
TD100/160
TD100/160
A(mm)
90
B(mm)
92
C(mm)
122
D(mm)
189.2
E(mm)
32.5
F(mm)
47
G(mm)
75
A-6-22
Overall dimensions
Plug-in device
Plug-in devices for TS100/160/250/400/630/800
[mm]
F
F
G
TS100/160/250/400/630
TS800
TS100/160/250
A-6-23
TS400/630
TS800
A(mm)
105
140
210
B(mm)
103.5
186.4
220
C(mm)
140
230
287
D(mm)
220
335.2
451
E(mm)
48.2
73
110
F(mm)
66
94.2
140
G(mm)
73
102
Overall dimensions
Plug-in device
Mounting to front plate
[mm]
B
A
Applicable to
A (mm)
TD100/160
TS100/160/250
TS400/630
TS800
30
35
46.5
70
B (mm)
90
105
140
210
C (mm)
160
182
290
387
D (mm)
E (mm)
173
M4 or 5
Front plate
202
314
422
M4 or 5
M5 or 6
M6 or 7
A-6-24
Overall dimensions
Plug-in device
Rail mounting
[mm]
Rail
Applicable to
TS400/630
TS800
A (mm)
30
70
100
156
B (mm)
76
77.8
101.6
104.2
C (mm)
14
28
32
43
D (mm)
A-6-25
TD100/160
M4 or 5
TS100/160/250
M6 or 7
M6 or 7
M8 or 9
Overall dimensions
Plug-in device
Mounting to rear plate with cover back
[mm]
Rear plate
Cover back
Applicable to
TD100/160
TS100/160/250
TS400/630
TS800
A (mm)
30
35
46.5
70
B (mm)
140
154
216
343
M4 or 5
M5 or 6
M6 or 7
C (mm)
M4 or 5
A-6-26
Overall dimensions
Plug-in device
Mounting for TD100/160
M4
375.2
26
5.3
34
62
34
92
34
[mm]
34
92
5.3
32.5
90
47
75
30
M4 or 5
30
A-6-27
326
262
14
4-M4 or 5
Overall dimensions
Terminal cover
ITS13E, ITS14E for TE100/160
24.5
150
[mm]
76
69.5
101
64.5
230
ITL13E, ITL14E for TE100/160
76
69.5
101
A-6-28
Overall dimensions
Terminal cover
ITS and ITL for TD100/160, TS100/160/250/400/630/800
[mm]
A
D(D')
C(C')
C(C')
Applicable to
Frame type
TD100, TD160
TS100, TS160, TS250
TS400, TS630
TS800
A-6-29
Type
Pole
Long
Dimension(mm)
Short
C
C
D
D
(Long type) (Short type) (Long type) (Short type)
type
type
2P, 3P
ITL13
ITS13
90
80.8
48.5
30.5
4P
ITL14
ITS14
120
80.8
32
25
2P, 3P
ITL23
ITS23
105
80.8
102
36.3
4P
ITL24
ITS24
140
80.8
98
32.3
2P, 3P
ITL33
ITS33
140
105
144.5
54.8
4P
ITL34
ITS34
186
105
138.5
48.8
2P, 3P
ITL43
ITS43
210
127.8
181.5
61.5
4P
ITL44
ITS44
280
127.8
172.5
52.5
196
160
321.4
190
479.4
300
600
360
Overall dimensions
Rear connection
RTF13, RTF14 for TE100/160
42.5
92.5
18
[mm]
13.8
135
25
25
70
25
130
150
8Nm
(82kgfcm)
8Nm
(82kgfcm)
A-6-30
Overall dimensions
Extended terminal
ET13E, ET14E for TE100/160
[mm]
21.5
50
45
81
50
130
170
190
8Nm
(82kgfcm)
25
70
16
82
76
5M ax
16
M
ax
8Nm
(82kgfcm)
A-6-31
Overall dimensions
Rear terminals
[mm]
TD100
TD160
30
122
30
30
TS100
TS160
TS250
35
140
35
35
TS400
TS630
46.5
230
46.5
46.5
TS800
287
70
70
70
A-6-32
Overall dimensions
Rear terminals
TD100 / TD160
[mm]
Bar type
4P(120)
2,3P(90)
122
Mounting plate: Max.3.2t
8.6
44
88
10
30
30
Round type
30
4P(120)
122
2,3P(90)
36
54
80
98
M8
30
Panel drilling
18
5
30
30
Front panel cutting

18
5
R2
30
30 30
2, 3P
A-6-33
30
30
30 30
4P
52
52
113.1
122
113.1
122
R2
90
2, 3P
120
4P
Overall dimensions
Rear terminals
TS100 / TS160 / TS250
[mm]
Bar type
4P(140)
2,3P(105)
140
8.2
43
11
89
35
35
Round type
35
4P(120)
140
2,3P(90)
36
54
82
100
M8
35
Panel drilling
35
35
Front panel cutting

20
5
20
5
35
35
35
35
2, 3P
35
35
4P
52
R2
52
125
140
125
140
R2
105
140
35
2, 3P
4P
A-6-34
Overall dimensions
Rear terminals
TS400 / TS630
[mm]
Bar type
4P(186.5)
2,3P(140)
230
13
50
114
15
46.5
Panel drilling
46.5
46.5
Front panel cutting

35
5
35
5
R2
46.5
A-6-35
46.5
46.5 46.5
46.5 46.5 46.5
2, 3P
4P
52 over
52 over
200
230
200
230
R2
140
2, 3P
186.5
4P
Overall dimensions
Rear terminals
TS800
[mm]
Bar type
4P(280)
2,3P(210)
287
13
37
16
81
70
122
168
Panel drilling
70
70
Front panel cutting
50
5
50
5
70
70
70
70
2, 3P
70
70
4P
52 over
R2
52 over
255
287
255
287
R2
210
280
2, 3P
4P
70
A-6-36
Overall dimensions
Circuit breaker with motor operator
MOP1, MOP2, MOP3, MOP4
TD100N/H/L
[mm]
Circuit breaker with MOP1
TD160N/H/L
TS100N/H/L
TS160N/H/L
88
61.2
TS250N/H/L
TS400N/H/L
45
52.5
81
45
195
90
105
140
140
93.5
TS630N/H/L
186.5
268.5
140
103.7
TS800N/H/L
65
105
65
130
140
130
210
A-6-37
65
105
128
308
280
Overall dimensions
Wiring connection
Motor operator
Standard connection
Circuit breaker On and Off controlled by remote operation and manual operation
P1
1. 2Nm
P2
S1
Power
Ue
S2
S4
ON
OFF
Connection with alarm switch (AL)

1) The below connection diagram is the method of using a alarm switch (AL) without shunt or
undervoltage trip.
fault.
Connection with FAL (only for the breakers with electronic trip unit ETS or ETM)
1) The below connection diagram is the method of using a FAL for circuit breakers with electronic
trip unit.
fault.
P1
P2
S1
S2
S4
ALb
Power
Ue
ALa
ALc
ON OFF
A-6-38
Overall dimensions
Wiring diagram(State of operation)
ETS23/ETS33/ETS43
The diagram is shown in the following conditions:
Fixed version circuit-breaker (depending on type of circuit-breaker)
Circuit breakers open.
Releases not tripped
L3
L1 L2 L3
OZ1
Downstream
Circuit Breaker
IZ2
IZ1
OZ2
OZ1
Upstream
Circuit Breaker
OZ2
L2
IZ1
L1
OZ2
OZ1
OZ2
IZ1
IZ2
C1
ETS23
ETS33
ETS43
COMMUNICATION
RS485 Modbus-RTU
C2
P1 G1
P2 G2
ETM33
ETM43
P1 +
P2
Three-pole circuit-breaker with
Three-pole circuit-breaker with
ETS23/ETS33/ETS43 electronic release
ETM33/ETM43 electronic release
(External natural current transformer)
A-6-39
DC24V
Overall dimensions
TS 1000, 1250, 1600A
Front Type
[mm]
Insulation barrier
320
Plate protection
25
25
283.5
Mounting hole
5.5
115.7
11
250
C
L
C
L
37.2
C
L
212
270
327
212
270
327
5.5
70
70
70
199
210
70
269
280
70
47.5
115.7
149.8
152.5
155.5
162.7
190.6
16.5
16.5
Trip button
Panel drilling
ON BACKPLATE
ON RAILS
4P
212
99.5
99.5
199
4P
4- 5.5 or M5
4- 5.5 or M5
212
4- 5.5 or M5
212
4- 5.5 or M5
3P
99.5
99.5
199
269
212
3P
269
Front panel cutting
67
200
199
95
199
15
119
119
67
4P
95
3P
4P
15
3P
200
A-6-40
Overall dimensions
TS 1000, 1250, 1600A
Front Type Busbar
[mm]
307
267
77
50
77
2525
Insulation barrier
404
362
18
77
25 25
25
77
25 25
115.7
16.5
15
Plate protection
Mounting hole
283.5
5.5
11
11
25
C
L
C
L
37.2
C
L
212
270
327
374
404
212
270
327
374
404
5.5
70
70
70
Trip button
199
210
Panel drilling
70
269
280
47.5
70
115.7
149.8
152.5
155.5
162.7
190.6
ON RAILS
3P
4P
212
4- 5.5 or M5
212
4- 5.5 or M5
99.5
99.5
199
269
Front panel cutting
A-6-41
67
199
200
199
95
15
119
119
67
4P
95
3P
4P
15
3P
200
Overall dimensions
TS 1000, 1250, 1600A
Rear Type
[mm]
210
199
114.7
280
269
Insulation barrier
84
43.5
14
15
42
135
372
C
L
C
L
37.2
C
L
212
258
212
258
283.5
Mounting hole
Trip button
31
31
115.7
149.8
152.5
155.5
162.7
190.6
44 70
25
44
Insulation barrier
70
11
11
25
70
70
70
Panel drilling
ON BACKPLATE
ON BACKPLATE
4P
3P
4- 5.5 or M5
75
140
99.5
199
212
25
60
25
60
270
235
75
212
200
165
75
212
75
60
60
75
212
75
60
75
75
60
4P
4- 5.5 or M5
60
4- 5.5 or M5
4- 5.5 or M5
60
3P
210
99.5
99.5
99.5
199
269
269
Front panel cutting
67
200
199
95
199
15
119
119
67
4P
95
3P
4P
15
3P
200
A-6-42
Overall dimensions
Rotary handles
Direct rotary handles for TS 1600AF
[mm]
A Type
380 (3P) Minimum
450 (4P) Minimum
205 Minimum
203
217
8.5
4.5
4- 7
46
33
196
210
t1.2~3.2
155.5
204.5
267
B Type
205 (3P) Minimum
275 (4P) Minimum
201
212
4.5
280 Minimum
4- 7
25.5
134
145
t1.2~3.2
204.5
267
Extended rotary handle for TS 1600AF

78
t1.2~3.2
246
681 Maximum (SHAFT Max. 469)
A-6-43
108
4- 6
24
108
Overall dimensions
Locking devices
Mechanical interlock for TS 1600AF
[mm]
The cutting of Panel

3P
TS1600
212
81
199
4P
TS1600
11
269
The dimension of installation holes
The cutting of Panel

3P
TS1600
212
81
199
4P
TS1600
11
269
A-6-44
Overall dimensions
Terminals
Front connection with bars for TS1600
Top terminal
[mm]
13.5
15 15
44
25
2-M10 Bolts
25
50
Bottom terminal
15 15
2-M10 Bolts
25
44
Rear connection with bars

44
25
12.5
2- 11
12.8
15
12.5
60
12 max.
25
50
38
Connection with Busbar
25
25
80
Left or right
busbar for 3P
Middle left or middle

right busbar for 4P
77
50
25
15
25
5- 11
25
52
A-6-45
15
5- 11
15
21
5- 11
52
82
52
82
30
30
15
25
82
52
82
15
30
52
5- 11
77
50
77
25
15
77
50
Left or right busbar

for 4P
21
Middle busbar
for 3P
12.5
30
25
60
25
50
15
12 max.
15
15
12 max.
25
52
25
52
25
52
Overall dimensions
Terminals
Front or Rear connection with vertical busbar for TS1600
[mm]
25
50
25
80
27
25
25
100
21
15
50/60/80/100
15
25
15
101
12 max.
15
25
25 12.5
60
89
25
26.5
12 max.
15
12 max.
15
12 max.
12 max.
25
25
15
15
20
Extension Busbar
50
80
23
184
150
50
5- 11
25
25
25
5- 13
25
A-6-46
A-7. Technical information

Temperature derating
TD, TS series up to 1600A
A-7-1
Power dissipation /Resistance

TD, TS series up to 1600A
A-7-7
Application
Primary use of transformer
Protection of lighting & heating circuits
Protection of resistance welding circuits
Use of circuit-breakers for capacitor banks
Using circuit-breakers in DC networks
Circuit breakers for 400Hz networks
Protection of several kinds of loads
A-7-8
A-7-10
A-7-11
A-7-12
A-7-15
A-7-16
A-7-18
Protective coordination
Discrimination & Cascading
Cascading, network 220/240V
Motor protection cascading, network 220/240V
Protection discrimination table, Discrimination
Motor protection discrimination table
Type 2 Coordination according to IEC60947-4-1
A-7-20
A-7-21
A-7-25
A-7-30
A-7-31
A-7-33
A-7-43
A-7-45
How to calculate short-circuit current value

Various short-circuit
With percent impedance
With a simple formula
Calculation example
Combination of transformer and impedance
Calculation example
Calculation graph
A-7-53
A-7-55
A-7-57
A-7-59
A-7-63
A-7-64
A-7-65
A-7-67
A derating of the rated operational current of the Susol TD and TS molded case circuit breaker is
necessary if the ambient temperature is greater than 40C. Namely, when the ambient temperature
is greater than 40C, overload-protection characteristics are slightly modified.
Electronic trip units are not affected by variations in temperature.
But, the maximum permissible current in the circuit breaker depends on the ambient temperature.
Derating chart
- Connection type: Standard
- Trip unit: FTU, FMU, ATU
MCCB
TD100
TD160
TS100
TS160
TS250
TS400
TS630
TS800
Rating
Fixed MCCB (c/w Thermal-magnetic trip unit)
(A)
10C
20C
30C
40C
45C
50C
60C
70C
16
16
16
16
16
16
15
14
13
20
20
20
20
20
19
19
18
16
25
25
25
25
25
24
23
22
21
32
32
32
32
32
31
30
28
26
40
40
40
40
40
39
38
35
33
50
50
50
50
50
48
47
44
41
63
63
63
63
63
61
59
56
52
80
80
80
80
80
78
75
71
66
100
100
100
100
100
97
94
88
82
125
125
125
125
125
121
117
110
103
160
160
160
160
160
155
150
141
131
40
40
40
40
40
39
38
35
33
50
50
50
50
50
48
47
44
41
63
63
63
63
63
61
59
56
52
80
80
80
80
80
78
75
71
66
100
100
100
100
100
97
94
88
82
125
125
125
125
125
121
117
110
103
160
160
160
160
160
155
150
141
131
200
200
200
200
200
194
188
176
164
250
250
250
250
250
242
234
220
205
300
300
300
300
300
291
281
264
246
400
400
400
400
400
388
375
353
328
500
500
500
500
500
484
469
441
410
630
630
630
630
630
610
591
555
517
800
800
800
800
800
775
750
705
656
Note) TD160 1pole MCCB is not applied to temperature derating.
A-7-1
Derating chart
- Connection type: Plug-in
- Trip unit: FTU, FMU, ATU
MCCB
TD100
TD160
TS100
TS160
TS250
TS400
TS630
TS800
Rating
Fixed MCCB (c/w Thermal-magnetic trip unit)
(A)
10C
20C
30C
40C
45C
50C
60C
70C
16
16
16
16
16
16
20
20
20
20
20
19
15
14
13
19
18
16
25
25
25
25
25
32
32
32
32
32
24
23
22
21
31
30
28
26
40
40
40
40
50
50
50
50
40
39
38
35
33
50
48
47
44
41
63
63
63
80
80
80
63
63
61
59
56
52
80
80
78
75
71
66
100
100
100
100
100
97
94
88
82
125
125
125
125
125
121
117
110
103
160
160
160
160
160
155
150
141
131
40
40
40
40
40
39
38
35
33
50
50
50
50
50
48
47
44
41
63
63
63
63
63
61
59
56
52
80
80
80
80
80
78
75
71
66
100
100
100
100
100
97
94
88
82
125
125
125
125
125
121
117
110
103
160
160
160
160
160
155
150
141
131
200
200
200
200
200
194
188
176
164
250
250
250
250
250
242
234
220
205
300
300
300
300
300
291
281
264
246
400
400
400
400
400
388
375
353
328
500
500
500
500
500
484
469
441
410
630
630
630
630
630
610
591
555
517
800
800
800
800
800
775
750
705
656
A-7-2
Size of busbar
The table below indicates the maximum rated current value for each type of connection,
depending on the ambient temperature.
Connection
T
TS1000
40
45
50
55
60
65
70
800
800
800
800
800
800
800
1000
1000
1000
1000
1000
1000
1000
TS1250
1250
1250
1250
1250
1250
1240
1090
TS1600
1600
1600
1560
1510
1470
1420
1360
45
50
55
60
65
70
Connection
T
Vertical rear
40
800
800
800
800
800
800
800
1000
1000
1000
1000
1000
1000
1000
TS1250
1250
1250
1250
1250
1250
1250
1180
TS1600
1600
1600
1600
1600
1600
1510
1460
TS1000
A-7-3
Front or horizontal rear
Derating table

TS1000 to TS1600 mounted

Using bar connection
- Cross section of bar: 1000 mm2
- Limit of temperature rising at terminal connection: 70k
Using the data below, it is possible to determine the maximum

permissible currents when making the connections to busbars for a
Vertical, TS1000/TS1600, taking into account the ambient
temperature around the switchboard and the IP value. Connection
to be made according to the busbar drawings supplied.
Permissible current at switchboard condition using above external terminal connections

T: 25C
T:30C
T:35C
T:40C
T:45C
IP40
IP40
IP40
IP40
IP40
IP40
TS1000 N/H/L
1000
1000
1000
1000
1000
1000
TS1250 N/H
1250
1250
1250
1250
1250
1250
TS1600 N/H
1350
1350
1300
1250
1200
1150
Model
T:50C

Using busbar connecting

T: 25C
T:30C
T:35C
T:40C
T:45C
IP40
IP40
IP40
IP40
IP40
IP40
TS1000 N/H/L
1000
1000
1000
1000
1000
1000
TS1250 N/H
1250
1250
1250
1250
1250
1200
TS1600 N/H
1450
1400
1350
1300
1250
1200
Model
T:50C
A-7-4
Derating table


using special external connections
Using the data below, it is possible to determine the permissible

current for a specified connection between TS1000/TS1600, fixed
and busbars depending on the ambient temperature around the
switchboard and the IP value.

T: 25C
T:30C
T:35C
T:40C
T:45C
IP40
IP40
IP40
IP40
IP40
IP40
TS1000 N/H/L
1000
1000
1000
1000
1000
1000
TS1250 N/H
1250
1250
1250
1250
1250
1250
TS1600 N/H
1600
1600
1600
1550
1500
1450
Model
A-7-5
T:50C
Installation recommendation
Protection degree provided by enclosures (IP Code) IEC 60529

IP
First characteristic numeral
(numerals 0 to 6, or letter
Second characteristic numeral
(numerals 0 to 8, or letter
Code letters (international Protection)

First characteristic numeral
Brief description
0
1
2
3
4
Non-protected
Protected against solid foreign objects
of 50mm
and greater
of 12.5mm
and greater
of 2.5mm
and greater
of 1.0mm
and greater
Dust-protected
Dust-tight
Definition
The object probe sphere of 50mm ,
shall not fully penetrate
The object probe sphere of 12.5mm ,
shall not fully penetrate
The object probe sphere of 2.5mm ,
shall not penetrate at all
The object probe of 1.0mm ,
shall not penetrate at all
Ingress of dust is not totally prevented, but dust shall not
penetrate in a quantity to interfere with satisfactory
operation of the apparatus or to impair safety
No ingress of dust
Second characteristic numeral

Brief description
0
1
Non-protected
Protected against vertically falling
water drops
Protected against vertically falling
water drops when enclosure tilted
up to 15
Protected against spraying water
Protected against spraying water
Protected against spraying jets
Protected against powerful water jets
Protected against the effects of

temporary immersion in water
Protected against the effects of

continuous immersion in water
Definition
Vertically falling drops shall have no harmful effects
Vertically falling drops shall have no harmful effects
when the enclosure is tilted at any angle up to 15 on
either side of the vertical
Water sprayed at an angle up to 60 on wither side of
the vertical shall have no harmful effects
Water splashed against the enclosure from and
direction shall have no harmful effects
Water projected in powerful jets against the enclosure
from and direction shall have no harmful effects
Water projected in powerful jets against the enclosure
from any direction shall have no harmful effects
Ingress of water in quantities causing harmful effects shall
not be possible when the enclosure is temporarily immersed
in water under standardized conditions of pressure and time
Ingress of water in quantities causing harmful effects
shall not be possible when the enclosure is
continuously immersed in water under conditions which
shall be agreed between manufacturer and used but
which are more severs than for numeral 7
A-7-6
Power dissipation / Resistance
Susol TD & TS series up to 1600A

AF
Rating (A)
Fixed
MCCB
Plug-in
MCCB
MCCB
Plug-in
MCCB
20
25
32
40
50
63
80
100
0.70
R (m)
5.60
5.60
3.80
3.80
1.84
1.34
1.10
0.91
Watt single pole
1.43
2.24
2.38
3.89
2.94
3.35
4.37
5.82
7.00
Watt three poles
4.30
6.72
7.13
11.67
8.83
10.05
13.10
17.47
21.00
0.78
R (m)
5.68
5.68
3.88
3.88
1.92
1.42
1.18
0.99
Watt single pole
1.45
2.27
2.43
3.97
3.07
3.55
4.68
6.34
7.80
Watt three poles
4.36
6.82
7.28
11.92
9.22
10.65
14.05
19.01
23.40
200
250
0.52
0.25
AF
Fixed
TD100 (3P & 4P)

16
TD160 (3P & 4P)
Rating (A)
100
125
R (m)
0.70
0.61
0.50
Watt single pole
7.00
9.53
12.80
21.00 28.59
38.40
Watt three poles

R (m)
0.78
0.69
7.80 10.78
14.85
Watt three poles
23.40 32.34
44.54
Rating (A)
MCCB
Plug-in
MCCB
MCCB
Plug-in
MCCB
Fixed
50
63
80
100
160
3.37
2.86
2.86
1.36
0.96
0.76
0.62
5.39
7.15
11.35
8.70
9.60
11.88
15.87
20.80 15.79
Watt three poles
16.18
21.45
34.05
26.11
28.80
35.63
47.62
62.40 47.38
3.43
2.92
2.92
1.42
1.02
0.82
0.68
R (m)
0.58
0.31
Watt single pole
5.49
7.30
11.59
9.09
10.20
12.81
17.41
23.20 19.54
Watt three poles
16.46
21.90
34.77
27.26
30.60
38.44
52.22
69.60 58.63
TS400, TS630 (3P, 4P)

300
400
R (m)
0.30
0.30
0.26
0.21
Watt single pole
26.82
47.68
65.25
83.35
73.81
73.81
Watt three poles
80.46 143.04 195.75 250.05
221.44
221.44
R (m)
500
TS800 (3P, 4P)
Rating (A)
630
700
800
0.12
0.12
0.34
0.34
0.30
0.25
0.14
0.14
Watt single pole
30.42
54.08
75.25
99.23
86.61
86.61
Watt three poles
91.26 162.24 225.75 297.68
259.84
259.84
AF
TS1000N/H, TS1250N/H, TS1600N/H
R (m)
TS1000L
630
800
1000
1250
1600
630
800
1000
0.027
0.027
0.027
0.027
0.027
0.046
0.046
0.046
Watt single pole
10.7
17.3
27.8
45.1
76.0
18.3
30.0
48.3
Watt three poles
32.1
51.8
83.4
135.4
228.1
54.8
90.1
144.9
Power dissipated per pole (P/pole): Watts (W).

Resistance per pole (R/pole): Milliohms (m) (measured cold).
Total power dissipation is the value measured at In, 50/60 Hz,
for a 3 pole or 4 pole circuit breaker (Power= 3I2R)
A-7-7
125
Watt single pole
Rating (A)
MCCB
TS100,TS160,TS250 (3P & 4P)

40
R (m)
AF
Fixed
0.58
Watt single pole
AF
Fixed
160
Application
Application for transformer protection
Transformer excitation surge current may possibly exceed 10 times rated current, with a danger of
nuisance tripping of the MCCB. The excitation surge current will vary depending upon the supply
phase angle at the time of switching, and also on the level of core residual magnetism.
So, its recommended to select proper circuit breakers according to the continuous current carrying
capacity of transformer. It requires to consider separately whether transformer is single phase or
three phase. The below table indicates the proper molded case circuit breaker suitable for each
transformer.
AC220V
Capacity of 3 phase
transformer (kVA)
Capacity of single
phase transformer (kVA)
Breaking capacity (kA)
(sym)
Below 1500
Below 2000
Below 300
85
100
TD100H
TD100N
160
Below 3000
42
100
Frame (A)
Below 1500
TS100N
TD160H
TD160N
TS160N
120
200
TD100L
TS100H
TS100L
TD160L
TS160H
TS160L
250
TS250N
TS250H
TS250L
400
TS400N
TS400H
TS400L
630
TS630N
TS630H
TS630L
800
TS800N
TS800H
TS800L
AC460V
Capacity of 3 phase
transformer (kVA)
(sym)
100
160
Frame (A)
250
Below 2000
50
TD100N
Below 3000
65
70
Below 4000
85
100
TD100H
TD100L
TS100N
TS100H
TS100L
TD160N
TD160H
TD160L
TS160N
TS160H
TS160L
TS250N
TS250H
TS250L
130
400
TS400N
TS400H
TS400L
630
TS630N
TS630H
TS630L
800
TS800N
TS800H
TS800L
A-7-8
Application
Application for transformer protection
(MCCBs for Transformer-Primary Use)
Transformers are used to change in the supply voltage, for both medium and low voltage supplies.
The choice of the protection devices should be considered transient insertion phenomena, during
which the current may reach values higher than the rated full load current; the phenomenon decays
in a few seconds.
The peak value of the first half cycle may reach values of 15 to 25 times the effective rated current.
For a protective device capable of protecting these units this must be taken into account.
Manufacturers data and tests have indicated that a protective device feeding a transformer must be
capable of carrying the following current values without tripping.
TD100/160, TS100~800 equipped with Thermal magnetic trip units

1 phase 230V
Transformer ratings (kVA)

3 phase 230V
1 phase 240V
1 phase 230V
MCCB rated
current
(A)
16
Trip unit
3 to 4
5 to 6
9 to 11
4 to 5
6 to 8
11 to 14
20
5 to 6
8 to 10
14 to 17
25
6 to 7
10 to 13
18 to 22
32
7 to 9
13 to 16
22 to 28
40
9 to 12
16 to 20
28 to 35
50
12 to 14
20 to 25
35 to 44
63
15 to 18
26 to 32
44 to 55
80
18 to 23
32 to 40
55 to 69
100
FTU
23 to 29
40 to 50
69 to 87
125
FMU
29 to 37
51 to 64
89 to 111
160
ATU
37 to 47
64 to 80
111 to 138
200
46 to 58
80 to 100
138 to 173
250
55 to 69
96 to 120
166 to 208
300
74 to 92
128 to 160
221 to 277
400
92 to 115
160 to 200
277 to 346
500
116 to 145
202 to 252
349 to 436
630
129 to 161
224 to 280
388 to 484
700
147 to 184
256 to 320
443 to 554
800
TS100~800 equipped with electronic trip units

1 phase 230V
A-7-9
Transformer ratings (kVA)

3 phase 230V
1 phase 400V
3 phase 400V
MCCB rated
current
(A)
4 to 7
6 to 13
11 to 22
40
Trip
unit
Ir max
setting
0.8
9 to 19
16 to 32
27 to 56
100
0.8
15 to 30
25 to 52
44 to 90
160
0.8
23 to 46
40 to 80
70 to 139
250
37 to 74
64 to 128
111 to 222
400
58 to 115
100 to 200
175 to 346
630
0.8
74 to 184
127 to 319
222 to 554
800
ETS
ETM
0.8
0.8
Application
Protection of lighting & heating circuits
In the lighting & heating circuits, switching-surge magnitudes and times are normally not sufficient
to cause serious tripping problems. But, in some cases, such as incandescent lamps, mercury arc
lamps, metal halide and sodium vapour, or other large starting-current equipment, the proper
selection should be considered.
Upon supply of a lighting installation, for a brief period an initial current exceeding the rated current
(corresponding to the power of the lamps) circulates on the network. This possible peak has a
value of approximately 1520 times the rated current, and is present for a few milliseconds; there
may also be an inrush current with a value of approximately 1.53 times the rated current, lasting
up to some minutes. The correct dimensioning of the switching and protection devices must take
these problems into account. Generally, it is recommended to make the maximum operating
current not to exceed 80% of the related current.
AC220V
The maximum
operating
current (A)
12
16
20
25
32
40
50
64
80
100
128
160
200
240
320
400
504
560
640
The rated Breaking capacity (kA)

current of sym
85
MCCB (A)
16
20
25
32
40
50
63
80
100
125
160
200
250
300
400
500
630
700
800
100
120
TD100H
200
TD100L
TD100N
TD100H
TS100N
TD100L
TS100H
TD100L
TS100L
TD160H
TS160N
TS160H
TD160L
TS160L
TS250N
TS250H
TS250L
TS400N
TS400H
TS400L
TS630N
TS630H
TS630L
TS800N
TS800H
TS800L
TD160N
AC460V
The maximum
operating
current (A)
The rated
current of
MCCB (A)
12
16
20
25
32
40
50
64
80
100
128
160
200
240
320
400
504
560
640
16
20
25
32
40
50
63
80
100
125
160
200
250
300
400
500
630
700
800

sym
50
65
70
85
100
TD100N
TS100N
TD100H
TS100H
TD100L
TS100L
TD160N
TS160N
TD160H
TS160H
TD160L
TS160L
TS250N
TS250H
TS250L
130
TS400N
TS400H
TS400L
TS630N
TS630H
TS630L
TS800N
TS800H
TS800L
A-7-10
Application
Protection of resistance welding circuits
Short circuit protection for resistance welding devices can be obtained by applying molded case
circuit breaker properly. These breakers permit normally high welding currents, but trip
instantaneously if a short circuit develops.
It's recommended to select proper circuit breaker according to the characteristics of welding
devices as the follow table.
Characteristics of welding device

Capacity (kVA)
Maximum input (kVA)
Applied circuit breaker (MCCB 2P)

220V (Single phase)
400V (Single phase)
TD100N/H/L 100A
15
35
TS100N/H/L 100A
TD100N/H/L 50A
TD160N/H/L 100A
TS100N/H/L 50A
TS160N/H/L 100A
TD100N/H/L 100A
TD160N/H/L 125A
30
65
TS160N/H/L 125A
TS250N/H/L 125A
TS100N/H/L 100A
TD160N/H/L 100A
TS160N/H/L 100A
TD160N/H/L 125A
55
140
TS250N/H/L 250A
TS160N/H/L 125A
TS250N/H/L 125A
A-7-11
Application
Application for protection of capacitor circuit
C
Capacitor circuit
In order to reduce system losses (less than 0.5W/kvar in low voltage) and voltage drops in the
power distribution system, reactive power compensation or power factor correction is generally
undertaken. As a result, the power fed into the system is used as active power and costs will be
saved through a reduction in the capacitive and inductive power factors. The compensation can be
carried out by the fixed capacitors and automatic capacitor banks. However, the disadvantages of
installing capacitors are sensitivity to over-voltages and to the presence of nonlinear loads.
L1
L2
L3
1
Examples of equipment which consume reactive energy are all those receivers which require
magnetic fields or arcs in order to operate, such as:
- Asynchronous motors: An asynchronous motor is a large consumer of inductive reactive energy.
The amount of reactive power consumed is between 20% and 25% of the
rated power of the motor (depending on its speed).
Breaker
Contactor
O/L
- Power Transformers: Power transformers are normally always connected. This means that
reactive energy is always consumed. Also, as a consequence of its
inductive nature, the reactive energy increases when the transformer is
loaded.
T2 T3
T1
C
M
Motor
- Discharge lamps, Resistance-type soldering machines, Dielectric type heating ovens, Induction
heating ovens, Welding equipments, Arc furnaces
L1
L2
L3
1
Breaker
Contactor
At the instant of closing a switch to energize a capacitor, the current is limited only by the
impedance of the network upstream of the capacitor, so that high peak values of current will occur
for a brief period, rapidly falling to normal operating values.
O/L
T1
T2 T3
C
M
According to the relevant standards IEC 60831-1/IEC 70, capacitors must function under normal
operating conditions with the current having a RMS value up to 1.3 times the rated current of the
capacitor. Additionally, a further tolerance of up to 15% of the real value of the power must be
taken into consideration. The maximum current with which the selected circuit-breaker can be
constantly loaded, and which it must also be able to switch, is calculated as follows:
Motor
L1
L2
L3
1
Breaker
Breaker
Maximum expected rated current= Rated current of the capacitor bank1.5 (RMS value)
Contactor
C
O/L
T1
T2
T3
M
Motor
Usual connection diagram
A-7-12
Application
220V, 50/60Hz Circuit
Capacitor rating
kVAR
5
Single-phase circuit
Three-phase circuit
Capacitor rated
MCCB rated
Capacitor rated
MCCB rated
current (A)
current (A)
current (A)
current (A)
22.7
40
20
10
45.5
80
26.2
40
15
68.2
125
39.4
63
20
90.9
160
52.5
80
25
113.6
200
65.6
100
30
136.4
225
78.7
125
40
181.8
300
105.0
160
50
227.3
400
131.2
200
75
340.9
630
196.8
300
100
454.5
700
262.4
400
150
681.8
393.7
630
200
909.1
524.9
800
300
1363.6
787.3
400
1818.2
1049.8
Notes) 1. The MCCB rated current should be approx. 150% of the capacitor rated current.
2. The MCCB short-circuit capacity should be adequate for the circuit short-circuit capacity.
A-7-13
13.1
Application
440V, 50/60Hz Circuit
Capacitor rating
kVAR
Single-phase circuit
Three-phase circuit
Capacitor rated
MCCB rated
Capacitor rated
MCCB rated
current (A)
current (A)
current (A)
current (A)
11.4
20
6.6
16
10
22.7
40
13.1
20
15
34.1
63
19.7
32
20
45.5
80
26.2
40
25
56.8
100
32.8
50
30
68.2
125
39.4
63
40
90.9
160
52.5
80
50
113.6
200
65.6
100
75
170.5
300
98.4
160
100
227.3
400
131.2
200
150
340.9
500
196.8
300
200
454.5
700
262.4
400
300
681.8
393.7
630
400
909.1
524.9
800
Notes) 1. The MCCB rated current should be approx. 150% of the capacitor rated current.
2. The MCCB short-circuit capacity should be adequate for the circuit short-circuit capacity.
A-7-14
Application
Using circuit-breakers in DC networks
Susol circuit-breakers for protection of power distribution with thermal overload and magnetic shortcircuit trip units are suitable for usage in DC networks.
The circuit-breakers with electronic overcurrent releases are not suitable for DC networks.
Circuit-breaker selection criteria
The followings are the most important criteria for selection of suitable circuit breaker for DC
networks.
The rated current determines the rating and size of the circuit-breaker (Equipment)
The rated voltage determines the number of poles in series necessary for breaking
The maximum short-circuit current at the connection point determines the breaking capacity
Setting range of the trip values
Thermal overload protection: Same setpoints as in 50/60Hz circuits
Instantaneous short-circuit protection: The response threshold increases by maximum 40%.
The following wiring diagrams are recommended since the current must flow through all
current paths in order to conform to the thermal tripping characteristic curve.
-(N)
-(N)
+(P)
+(P)
Load
Load
Recommended wiring method

for DC500V circuit
Model
Recommended wiring method

for DC600V circuit
Trip unit
TD100N,TD160N
Applicable to DC circuits
42
50
65
85
100
TS100N,TS160N, TS250N
TS400N, TS630N
TS800N
TD100H, TD160H
Thermal
magnetic
FTU
TS400H, TS630H
FMU
TS800H
ATU
TD100L, TD160L
TS400L, TS630L
TS800L
Electronic
A-7-15
TS250, TS630, TS800
ETS, ETM
Impossible to use to DC circuits
Application
When circuit breakers are used at high frequencies, the breakers in many cases require to be
derated as the increased resistance of the copper sections resulting from the skin effect produced
by eddy currents at 400Hz.
Standard production breakers can be used with alternating currents with frequencies other than
50/60 Hz (the frequencies to which the rated performance of the device refer, with alternating
current) as appropriate derating coefficients are applied.

Thermal trip
As can be seen from the data shown in below, the tripping threshold of the thermal element (ln)
decreases as the frequency increases because of the reduced conductivity of the materials and the
increase of the associated thermal phenomena.
Rated current (A) at 400Hz= K1 rated current (A) at 50/60Hz
Instantaneous trip
The magnetic threshold increases with the increase in frequency.
Instantaneous current (A) at 400Hz= K2Instantaneous current (A) at 50/60Hz

TD and TS series performance table at 400Hz
Rated current
(A)
in 400 Hz
Applied circuit breaker

(MCCB)
Multiplier factors (K1, K2)

Trip unit
K1
K2
(Thermal trip units)
(Magnetic trip units)
16
0.8
20
0.8
25
0.8
32
TD100N, TD100H, TD100L
0.8
40
TS100N, TS100H, TS100L
0.8
50
TD160N, TD160H, TD160L
0.8
63
0.8
80
0.8
0.8
0.8
0.8
200
0.8
250
0.8
FTU
100
FMU
125
160
ATU
300
0.8
400
0.8
500
0.8
630
0.8
0.8
700
Note) K1Multiplier factor of rated current (In)
K2-Multiplier factor of instantaneous current due to the induced magnetic fields
FTU-Fixed Thermal and magnetic trip unit
FMUAdjustable thermal and fixed magnetic trip unit
ATUAdjustable thermal and magnetic trip unit
A-7-16
Application
Electronic trip units
The use of electronics offers the advantage of greater operating stability when the frequency is
varied. However, the devices are still subjected to frequency related temperature effects which may
sometimes pose restrictions on their use. Column K1 of the table below gives the maximum
permissible current to be used for the current setting (knob position).
Rated current
(A)
in 400 Hz
40
80
160
250
400
630
Applied circuit breaker

(MCCB)
Multiplier factors (K1, K2)

Trip unit
K2
(Thermal trip units)
(Magnetic trip units)
0.4 to 1

ETS
ETM

800
Note) ATUAdjustable thermal and magnetic trip unit
K1Multiplier factor of rated current (In)
K2-Multiplier factor of instantaneous current due to the induced magnetic fields
ETSElectronic trip unit (Standard)
ETMElectronic trip unit (Multi-function)
A-7-17
K1
0.4 to 1
0.4 to 0.9
0.4 to 0.9
0.4 to 0.8
0.4 to 0.8
0.4 to 0.75
0.97
Application
Application for protection of several kinds of loads
It requires to select proper circuit breakers according to the characteristics of loads when they are
installed to protect several kinds of loads. It's needed to consider the maximum operating current
and the capacity of loads in total so as to select the rated current of breakers.
Selection of circuit breaker protecting the several loads simultaneously
The kind of loads
Permissible current
The rated current
(IM: motors, IL: others)
in cable or wire: IW
of circuit breaker: Ib
In case of,
IM IL
M IM1
Ib
Iw
M IM2
IL1
IW IM + IL
Choose the low value among
IL2
In case of,
IM IL,
Ib
Iw
IM 50A
two formulas:
M IM1
Ib 3IM + IL. and
M IM2
Ib 2.5IW
IL1
Iw 1.25IM + IL
Its permitted to select the above value
IL2
only if IW (above 100A) isnt subject to
In case of,
IM IL, Ib
M IM1
Iw
IM 50A
M IM2
IL1
the rated current of circuit breaker.

IW 1.1IM + IL
IL2
The rated current of breakers as the main circuit of 3 phase inductive loads (AC 220V)
Capacity of
loads In total
(below kW)
3
4.5
6.3
8.2
12
15.7
19.5
23.2
30
37.5
45
52.5
63.7
75
86.2
97.5
112.5
125
150
175
The maximum
Capacity of the highest motor (kW / A)
operating current 0.75 1.5 2.2 3.7 5.5 7.5 11 15 18.5 22 30

(below A)
15
20
30
40
50
75
90
100
125
150
175
200
250
300
350
400
450
500
600
700
4.8
20
32
40
50
63
100
100
125
160
200
200
250
300
400
400
500
500
630
700
800
8
32
32
40
50
63
100
100
125
160
200
200
250
300
400
400
500
500
630
700
800
11.1 17.4
32
32 50
40 50
50 50
63 63
100 100
100 100
125 125
160 160
200 200
200 200
250 250
300 300
400 400
400 400
500 500
500 500
630 630
700 700
800 800
37 45
55 75 90
26 34
48 65
79 93 125 160 190 230 310 360
63
80
80
100
100
125
160
200
200
250
300
400
400
500
500
630
700
800
125
125
125
160
200
200
250
300
400
400
500
500
630
700
800
200
200
200
200
200
250
300
400
400
500
500
630
700
800
100
100
100
100
125
160
200
200
250
300
400
400
500
500
630
700
800
160
160
160
160
200
200
250
300
400
400
500
500
630
700
800
200
250
250
250
250
300
400
400
500
500
630
700
800
300
300 400
300 400
300 400
400 400
400 400
500 500
500 500
630 630
700 700
800 800
500
500
500
500
500
500
630
700
800
500
500
500
500
500
630
700
800
630
630
700
700
700
800
700
700
700
800
800
A-7-18
Application
The rated current of breakers as the main circuit of 3 phase inductive loads (AC 440V)
Capacity The maximum
Capacity of the highest motor (kW / A)
of loads
operating
0.75
1.5
2.2
3.7
5.5
7.5
11 15 18.5 22 30 37 45 55 75 90 110 132
In total
current
(below kW)
(below A) 4.8 8 11.1 17.4 26 34 48 65 79 93 125 160 190 230 310 360 220 250
3
7.5
16 16
16
16 32
4.5
10
16 16
6.3
15
20 20
20 32 40
8.2
20
32 32
32 32 40 50
12
25
32 32
32 32 40 50
15.7
38
50 50
50 50 50 50 63 80
19.5
45
50 50
50 50 50 50 63 80 100
23.2
50
63 63
63 63 63 63 63 80 100 125
30
63
80 80
80 80 80 80 80 100 100 125
37.5
75
100 100 100 100 100 100 100 100 100 125 160
45
88
100 100 100 100 100 100 100 100 100 125 160 200
52.5
100
125 125 125 125 125 125 125 125 125 125 160 200 250
63.7
125
160 160 160 160 160 160 160 160 160 160 160 200 250 250
75
150
200 200 200 200 200 200 200 200 200 200 200 200 250 250
86.2
175
200 200 200 200 200 200 200 200 200 200 200 200 250 300 400
97.5
200
250 250 250 250 250 250 250 250 250 250 250 250 250 300 400 400 500
112.5
225
250 250 250 250 250 250 250 250 250 250 250 250 250 300 400 400 500 500
125
250
300 300 300 300 300 300 300 300 300 300 300 300 300 300 400 400 500 500
150
300
400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 500 500
175
350
400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 500 630 630
200
400
500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 700 700
250
500
630 630 630 630 630 630 630 630 630 630 630 630 630 630 630 630 800 800
300
600
700 700 700 700 700 700 700 700 700 700 700 700 700 700 700 700 800 800
350
700
800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800
400
700
800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800
Notes) The above mentioned technical data is defined under the usage conditions as follows ;
1. The circuit breaker is tripped within 10seconds in 600% of the current of the fully operating loads.
2. The start-up input current is set within 1700% of the current of the fully operating loads.
3. The capacity of highest motor is also applied when several loads starts up simultaneously.
A-7-19
Discrimination & Cascading
The primary purpose of a circuit protection system is to prevent damage to series
connected equipment and to minimize the area and duration of power loss.
The first consideration is whether an air circuit breaker or molded case circuit
breaker is the most suitable. The next is the type of system to be used.
The two major types are: Discrimination and cascading.
Discrimination
According to IEC60947-2, the discrimination can be defined as follows.
Total discrimination (total selectivity)
Over-current discrimination where, in the presence of two over-current protective devices in series,
the protective device on the load side effects the protection without causing the other protective
device to operate.
Main breaker
Comtinuous supply
Branch breaker
Short-circuit point
Healthy circuit
<Discrimination>
Partial discrimination (partial selectivity)

Over-current discrimination where, in the presence of two over-current protective devices in series,
the protective device on the load side effects the protection up to a given level of over-current,
without causing the other protective device to operate.
No discrimination
In case of a fault, main and branch circuit breakers open.
Cascading
Main breaker
Branch
breaker
This is an economical approach to the use of circuit breakers, whereby only the main (upstream)
breaker has adequate interrupting capacity for the maximum available fault current.
The MCCBs downstream cannot handle this maximum fault current and rely on the opening of the
upstream breaker for protection.
The advantage of the cascade back-up approach is that it facilitates the use of low cost, low fault
level breakers downstream, thereby offering savings in both the cost and size of equipment.
As Susol TD & TS circuit breakers have a very considerable current limiting effect, they can be
used to provide this cascade back-up protection for downstream circuit breakers.
Fault point
<Cascading>
A-7-20
Complementary technical information
Main: Susol TD/TS series
Main breaker
Branch breaker
Rated breaking
capacity (kArms)
ABS33c
AB
Susol
TD
&
TS
A-7-21
30
Branch: Metasol AB and Susol MCCB

TD100N TD100H TD100L TD160N TD160H TD160L TS100N TS100H TS100L
85
100
200
50
50
65
85
50
100
200
100
120
200
50
65
65
65
85
ABN53c
30
50
50
65
50
50
65
85
100
100
ABS53c
35
65
65
85
65
65
85
100
120
120
ABH53c
100
ABN63c
30
50
65
65
65
65
65
85
120
85
120
85
ABS63c
35
65
85
100
85
85
100
85
100
100
ABN103c
35
85
100
120
85
100
120
100
120
120
200
100
ABS125c
85
ABH125c
100
ABN203c
65
ABS203c
85
ABH203c
100
ABN403c
50
ABS403c
75
ABH403c
85
ABL403c
125
ABN803c
50
ABS803c
85
ABL803c
125
TD100N
85
TD100H
100
TD160N
85
TD160H
100
TS100N
100
TS100H
120
TS160N
100
TS160H
120
TS250N
100
TS250H
120
TS400N
100
TS400H
120
TS630N
100
TS630H
120
TS800N
100
TS800H
120
TS1000N
55
TS1000H
75
TS1250N
55
TS1250H
75
100
200
100
200
200
100
120
200
120
200
120
200
200
200
200
Main: Susol TS series
Main breaker
Branch breaker
Rated breaking
capacity (kArms)
ABS33c
AB
Susol
TD
&
TS
30
TS160NTS160H TS160L TS250NTS250H TS250LTS400N TS400H TS400L

100
120
200
100
120
200
65
65
85
50
50
65
65
ABN53c
30
85
100
100
50
50
ABS53c
35
100
120
120
65
65
85
ABH53c
100
120
120
ABN63c
30
65
85
65
65
85
65
100
120
200
ABS63c
35
85
100
100
85
85
100
ABN103c
35
100
120
120
85
100
120
100
100
120
100
120
150
120
150
100
120
150
100
ABS125c
85
ABH125c
100
ABN203c
65
85
85
100
85
85
ABS203c
85
100
100
120
100
120
150
ABH203c
100
120
150
100
120
150
ABN403c
50
85
100
100
ABS403c
75
100
120
120
ABH403c
85
100
120
150
ABL403c
125
ABN803c
50
ABS803c
85
ABL803c
125
TD100N
85
TD100H
100
200
100
100
120
200
120
200
100
100
120
200
120
200
100
200
120
200
TD160N
85
120
200
120
200
120
200
TD160H
100
120
200
120
200
120
200
TS100N
100
120
200
120
200
120
200
TS100H
120
TS160N
100
TS160H
120
TS250N
100
TS250H
120
TS400N
100
TS400H
120
TS630N
100
TS630H
120
TS800N
100
TS800H
120
TS1000N
55
TS1000H
75
TS1250N
55
TS1250H
75
200
120
200
100
120
200
120
200
200
200
120
200
120
200
200
120
200
200
200
200
120
200
200
A-7-22
Main breaker
Branch breaker
Rated breaking
capacity (kArms)
ABS33c
AB
Susol
TD
&
TS
A-7-23
TS630N
TS630H
TS630L
TS800N
TS800H
TS800L
100
120
200
100
120
200
30
ABN53c
30
ABS53c
35
ABH53c
100
ABN63c
30
ABS63c
35
ABN103c
35
ABS125c
85
100
120
150
ABH125c
100
100
120
150
ABN203c
65
85
85
100
ABS203c
85
100
120
150
ABH203c
100
100
120
150
ABN403c
50
85
100
100
85
100
100
ABS403c
75
100
120
120
100
120
120
ABH403c
85
100
120
150
100
120
ABL403c
125
ABN803c
50
ABS803c
85
ABL803c
125
TD100N
85
TD100H
100
200
150
200
100
120
120
120
150
200
100
200
200
100
200
200
85
120
200
120
200
TD160H
100
120
200
120
200
TS100N
100
120
200
120
200
TS100H
120
TS160N
100
TS160H
120
TS250N
100
TS250H
120
TS400N
100
TS400H
120
TS630N
100
TS630H
120
TS800N
100
TS800H
120
TS1000N
55
TS1000H
75
55
TS1250H
75
100
120
120
TD160N
TS1250N
100
120
120
200
120
200
200
120
200
120
200
200
120
200
200
200
120
200
200
120
200
120
200
200
120
200
200
200
200
120
200
200
Main breaker
Branch breaker
Rated breaking
capacity (kArms)
ABS33c
AB
Susol
TD
&
TS
TS1000N TS1000H TS1000L TS1250N TS1250H TS1600N TS1600H

55
75
200
55
75
55
75
75
200
55
75
55
75
55
75
55
75
30
ABN53c
30
ABS53c
35
ABH53c
100
ABN63c
30
ABS63c
35
ABN103c
35
ABS125c
85
ABH125c
100
ABN203c
65
ABS203c
85
ABH203c
100
ABN403c
50
ABS403c
75
200
ABH403c
85
200
ABL403c
125
ABN803c
50
55
200
55
75
200
ABS803c
85
ABL803c
125
200
200
TD100N
85
200
TD100H
100
200
TD160N
85
200
TD160H
100
200
TS100N
100
200
TS100H
120
200
TS160N
100
200
TS160H
120
200
TS250N
100
200
TS250H
120
200
TS400N
100
200
TS400H
120
200
TS630N
100
200
TS630H
120
200
TS800N
100
200
TS800H
120
200
TS1000N
55
200
TS1000H
75
200
TS1250N
55
200
TS1250H
75
200
75
75
75
75
A-7-24
Main breaker
Branch breaker Rated breaking
capacity (kArms)
AB
Susol
TD
&
TS
A-7-25

TD100NTD100H TD100L TD160NTD160H TD160LTS100N TS100H TS100L
50
85
150
50
85
150
50
85
150
ABS33c
14
25
30
30
25
30
30
30
40
40
ABN53c
14
35
50
50
35
50
50
35
65
65
ABS53c
18
50
65
65
50
65
65
50
70
70
ABH53c
50
ABN63c
14
25
30
30
25
30
30
30
40
40
ABS63c
18
35
50
50
35
50
50
35
65
65
ABN103c
18
50
65
65
50
65
65
50
70
70
ABS125c
37
50
65
65
50
65
65
50
70
70
ABH125c
50
ABN203c
26
ABS203c
37
ABH203c
50
ABN403c
37
ABS403c
50
ABH403c
65
ABL403c
85
ABN803c
37
ABS803c
65
ABL803b
85
TD100N
50
TD100H
85
TD160N
50
TD160H
85
TS100N
50
TS100H
85
TS160N
50
TS160H
85
TS250N
50
TS250H
85
TS400N
65
TS400H
85
TS630N
65
TS630H
85
TS800N
65
TS800H
85
TS1000N
50
TS1000H
70
TS1250N
50
TS1250H
70
85
150
85
150
150
85
150
85
150
150
150
150
85
150
150
Main breaker
Branch breaker
Rated breaking
capacity (kArms)
AB
Susol
TD
&
TS
TS160NTS160H TS160L TS250NTS250H TS250LTS400N TS400H TS400L

50
85
150
50
85
150
ABS33c
14
30
40
40
30
40
40
ABN53c
14
35
65
65
35
65
65
ABS53c
18
50
70
70
50
70
70
ABH53c
50
ABN63c
14
30
40
40
30
65
70
40
40
65
85
150
50
70
85
85
100
70
ABS63c
18
35
65
65
35
65
65
ABN103c
18
50
70
70
50
70
70
ABS125c
37
50
70
70
40
65
70
ABH125c
50
70
70
70
85
ABN203c
26
35
50
50
40
50
ABS203c
37
40
65
70
50
70
85
ABH203c
50
70
85
85
100
ABN403c
37
70
85
ABS403c
50
85
100
ABH403c
65
85
120
ABL403c
85
ABN803c
37
ABS803c
65
ABL803b
85
TD100N
50
TD100H
85
TD160N
50
TD160H
85
TS100N
50
TS100H
85
TS160N
50
TS160H
85
TS250N
50
TS250H
85
TS400N
65
TS400H
85
TS630N
65
TS630H
85
TS800N
65
TS800H
85
TS1000N
50
TS1000H
70
TS1250N
50
TS1250H
70
50
150
85
150
85
150
85
150
85
150
85
150
150
65
85
150
85
150
65
85
85
150
65
85
150
150
150
65
85
150
85
150
150
150
150
150
150
150
150
85
150
150
150
150
65
85
150
150
150
85
150
150
A-7-26
Main breaker
Branch breaker Rated breaking
capacity (kArms)
ABS33c
AB
Susol
TD
&
TS
A-7-27
TS630N
TS630H
TS630L
TS800N
TS800H
TS800L
65
85
150
65
100
150
50
70
85
85
100
70
50
70
85
85
100
65
100
120
100
150
14
ABN53c
14
ABS53c
18
ABH53c
50
ABN63c
14
ABS63c
18
ABN103c
18
ABS125c
37
ABH125c
50
ABN203c
26
40
50
ABS203c
37
50
70
85
ABH203c
50
85
100
ABN403c
37
70
85
ABS403c
50
85
100
ABH403c
65
85
120
ABL403c
85
ABN803c
37
65
85
100
ABS803c
65
65
100
120
ABL803b
85
TD100N
50
TD100H
85
TD160N
50
TD160H
85
TS100N
50
TS100H
85
TS160N
50
TS160H
85
TS250N
50
TS250H
85
TS400N
65
TS400H
85
TS630N
65
TS630H
85
TS800N
65
TS800H
85
TS1000N
50
TS1000H
70
TS1250N
50
TS1250H
70
50
150
65
85
150
65
100
150
100
150
150
65
85
150
150
65
100
150
65
85
150
65
100
150
65
85
150
85
150
65
100
150
65
100
150
150
150
100
150
85
150
150
150
85
150
150
150
65
150
150
150
150
100
150
150
150
100
150
Main breaker
Branch breaker
Rated breaking
capacity (kArms)
ABS33c
AB
Susol
TD
&
TS

50
70
150
50
70
50
70
70
150
50
70
50
70
14
ABN53c
14
ABS53c
18
ABH53c
50
ABN63c
14
ABS63c
18
ABN103c
18
ABS125c
37
ABH125c
50
ABN203c
26
ABS203c
37
ABH203c
50
ABN403c
37
ABS403c
50
70
150
70
70
ABH403c
65
70
150
70
70
ABL403c
85
ABN803c
37
ABS803c
65
ABL803b
85
TD100N
50
TD100H
85
TD160N
50
TD160H
85
TS100N
50
TS100H
85
TS160N
50
TS160H
85
TS250N
50
TS250H
85
TS400N
65
TS400H
85
TS630N
65
TS630H
85
TS800N
65
TS800H
85
TS1000N
50
TS1000H
70
TS1250N
50
TS1250H
70
50
150
50
70
70
150
150
50
70
50
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
150
70
150
150
70
150
150
70
150
150
70
150
150
70
150
150
70
150
150
70
150
150
70
150
150
70
150
150
70
150
150
A-7-28
Branch: Susol MCCB
Main breaker
Branch breaker
Rated breaking
capacity (kArms)
Susol
TD
&
TS
TD100N
85
TD100H
100
TD160N
85
TD160H
100
TS100N
100
TS100H
120
TS160N
100
TS160H
120
Main breaker
Branch breaker
Rated breaking
capacity (kArms)
Susol
TD
&
TS
100
100
200
85
200
100
100
200
100
120
200
100
120
200
100
120
200
100
120
200
120
200
120
200
120
200
120
200
TD160H
100
120
200
120
TS100N
100
120
200
120
TS100H
120
TS160N
100
TS250H
120
Rated breaking
capacity (kArms)
TD100N
85
TD100H
100
TD160N
85
TD160H
TS100N
TS100H
120
Susol TS160N
TD TS160H
100
TS250N
100
100
200
120
200
120
100
TS800H
120
200
120
200
200
120
200
120
200
120
200
200
120
200
200
200
200
100
120
200
100
120
200
100
100
100
120
200
120
200
120
200
200
120
200
200
120
200
120
200
120
200
120
200
120
200
100
200
120
200
120
200
120
200
120
200
120
TS800N
200
TS800L
120
TS630H
200
120
100
TS800H
120
120
200
TS800N
100
100
120
TS630L
100
TS630N
200
TS630H
200
TS400H
100
120
TS630N
120
120
100
200
200
100
200
200
200
TS400N
120
120
120
200
120
TS250H
200
200
200
120
100
120
120
200
100
85
120
200
TS160N TS160H TS160L TS250N TS250H TS250L TS400N TS400H TS400L
TD160N
100
100
120
200
85
TS250N
200
100
200
100
TS160H
200
200
TD100H
Main breaker
A-7-29
85
TD100N
Branch breaker
&
TS
200
200
200
200
200
200
200
200
200
120
200
200

Branch: Susol MCCB
Main breaker
Branch breaker
Rated breaking
capacity (kArms)
Susol
TD
&
TS

55
75
200
TD100N
85
TD100H
100
200
TD160N
85
200
TD160H
100
200
TS100N
100
200
TS100H
120
200
TS160N
100
200
TS160H
120
200
TS250N
100
200
TS250H
120
200
TS400N
100
200
TS400H
120
200
TS630N
100
200
TS630H
120
200
TS800N
100
200
TS800H
120
200
TS1000N
55
200
TS1000H
75
200
TS1250N
55
200
TS1250H
75
200
55
75
55
75
200
75
75
75
75
A-7-30
Branch: Susol MCCB
Main breaker
Branch breaker
Rated breaking
capacity (kArms)
Susol
TD
&
TS
TD100N
50
TD100H
85
TD160N
50
TD160H
85
TS100N
50
TS100H
85
TS160N
50
TS160H
85
Main breaker
Branch breaker
Rated breaking
capacity (kArms)
Susol
TD
&
TS
TD100N
50
TD100H
85
TD160N
50
TD160H
85
TS100N
50
TS100H
85
TS160N
50
TS160H
85
TS250N
50
TS250H
85
Main breaker
Branch breaker
Rated breaking
capacity (kArms)
Susol
TD
&
TS
A-7-31
TD100N
50
TD100H
85
TD160N
50
TD160H
85
TS100N
50
TS100H
85
TS160N
50
TS160H
85
TS250N
50
TS250H
85
TS400N
65
TS400H
85
TS630N
65
TS630H
85
TS800N
65
TS800H
85

85
100
85
200
85
150
100
85
150
200
100
150
120
85
150
85
200
150
150
150
150
85
150
150
TS160N TS160H TS160L TS250N TS250H TS250L TS400N TS400H TS400L

100
120
200
85
150
100
120
85
150
85
150
85
120
150
65
85
150
85
150
65
85
65
85
85
150
150
150
150
150
150
65
85
65
85
150
85
150
150
150
150
200
150
150
150
150
85
100
150
150
85
200
150
150
150
150
150
TS630N
TS630H
TS630L
TS800N
TS800H
TS800L
100
120
200
100
120
200
65
85
150
65
100
150
65
85
150
65
85
150
65
100
65
100
150
85
150
65
85
150
65
100
65
100
85
150
150
150
150
150
150
150
150
85
150
150
150
65
150
150
150
150
100
150
150
150
100
150
150
150
100
150

Branch: Susol MCCB
Main breaker
Branch breaker
Rated breaking
capacity (kArms)
Susol
TD
&
TS
TD100N
50
TD100H
85
TD160N
50
TD160H
85
TS100N
50
TS100H
85
TS160N
50
TS160H
85
TS250N
50
TS250H
85
TS400N
65
TS400H
85
TS630N
65
TS630H
85
TS800N
65
TS800H
85
TS1000N
50
TS1000H
70
TS1250N
50
TS1250H
70

55
75
70
200
150
55
75
55
75
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
150
70
150
150
70
150
150
70
150
150
70
150
150
70
150
150
70
150
150
70
150
150
70
150
150
70
150
150
A-7-32
Main: Susol MCCB 100~800AF
Branch
breaker
Main breaker
Trip unitsThermal
magnetic
AB125
AB203 S
A-7-33
Trip unitsThermal
magnetic
TD160N/H/L
Trip units-Thermal magnetic

16
AB100 N
TD100N/H/L
Rating (A)
~10
15
20
30
40
50
60
75
100
15
20
30
40
50
60
75
100
125
15
20
30
40
50
60
75
100
125
100
125
150
175
200
225
250
100
125
150
175
200
225
250
100
125
150
175
200
225
250
Branch: AB type MCCB
20
25
32
40
50
63
80
100
100
125
160
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.63
0.63
0.63
0.63
0.63
0.63
0.8
0.8
0.8
0.8
0.8
0.8
0.8
T
T
9
9
9
8
8
T
T
9
9
9
8
8
8
0.5
0.5
0.5
0.5
0.5
0.63
0.63
0.63
0.63
0.63
0.8
0.8
0.8
0.8
0.8
0.8
10
9
9
9
8
8
8
10
10
9
9
8
8
8
8
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.63
0.63
0.63
0.63
0.63
0.63
0.8
0.8
0.8
0.8
0.8
0.8
0.8
10
9
9
9
8
8
8
10
10
9
9
8
8
8
8
T
T
9
9
9
8
8
8
8
10
10
9
9
8
8
8
8
8
10
10
9
9
8
8
8
8
0.5
TS100N/H/L
TS160N/H/L
TS250N/H/L
TS400N/H/L
TS630N/H/L
TS800N/H/L
Trip units-Thermal magnetic/Electronic

40
50
63
80
100
100
125
160
125
160
200
250
300
400
500
630
800
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
10
10
10
10
10
10
8
11
10
10
8
8
11
11
11
11
11
8
11
11
11
11
11
8
12.5
11
11
11
11
8
8
10
10
10
10
10
10
8
11
10
10
8
8
11
11
11
11
11
8
11
11
11
11
11
8
12.5
11
11
11
11
8
8
T
T
T
T
T
T
T
T
T
12.5
12.5
11
11
11
11
11
11
11
12.5
12.5
11
11
11
11
11
11
11
8
8
T
T
T
T
T
T
T
T
T
15
15
15
15
15
12.5
12.5
12.5
12.5
15
15
15
15
15
12.5
12.5
12.5
12.5
T
T
T
T
T
T
T
T
T
15
15
15
15
15
12.5
12.5
12.5
12.5
15
15
15
15
15
12.5
12.5
12.5
12.5
T
T
T
T
T
T
T
T
T
18
15
15
15
15
12.5
12.5
12.5
12.5
18
15
15
15
15
12.5
12.5
12.5
12.5
8
T
T
T
T
T
T
T
T
T
18
18
18
15
15
12.5
12.5
12.5
12.5
18
18
18
15
15
12.5
12.5
12.5
12.5
8
8
T
T
T
T
T
T
T
T
T
T
T
20
20
20
20
20
20
20
25
25
20
20
20
20
20
20
20
T
T
15
12.5
11
11
11
18
18
15
12.5
11
11
11
18
18
15
12.5
11
11
11
T
T
T
T
T
T
T
T
T
T
T
T
T
20
20
20
20
20
25
25
25
25
20
20
20
20
20
T
T
15
12.5
12.5
11
11
18
18
15
12.5
12.5
11
11
18
18
15
12.5
12.5
11
11
T
T
T
T
T
T
T
T
T
T
T
T
T
T
20
20
20
20
25
25
25
25
25
20
20
20
20
T
T
15
15
12.5
12.5
12.5
18
18
15
15
12.5
12.5
12.5
18
18
15
15
12.5
12.5
12.5
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
25
25
25
25
25
25
25
25
25
T
T
15
15
12.5
12.5
12.5
18
18
15
15
12.5
12.5
12.5
18
18
15
15
12.5
12.5
12.5
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
28
28
28
28
28
28
28
8
8
8
8
8
8
8
8
A-7-34
Main: Susol TD 100/160
Branch
breaker
Branch: Susol TD 100/160
Main breaker
TD100N/H/L
TD160N/H/L
Rating (A)
16
20
25
32
40
50
63
80
100
100
125
160
0.4
0.5
0.5
0.5
0.63
0.8
20
0.5
0.5
0.63
0.8
25
0.5
0.5
0.63
0.8
0.5
0.63
0.8
40
0.63
0.8
50
0.63
0.8
0.8
1.25
16
32
N
63
80
1.6
100
0.5
0.5
0.63
0.8
20
0.5
0.5
0.63
0.8
25
0.5
0.5
0.63
0.8
0.5
16
0.5
0.63
0.8
40
0.63
0.8
50
0.63
32
TD100 H
63
80
Trip units100
Thermal
16
magnetic
20
2
2
1.25
1.6
0.5
0.63
0.8
0.5
0.63
0.8
0.5
0.5
0.63
0.8
0.5
0.63
0.8
40
0.63
0.8
50
0.63
0.8
0.8
63
2
2
0.5
32
L
2
2
0.5
25
0.5
0.8
0.8
80
1.25
100
1.6
100
1.6
125
1.25
160
TD160 H
100
1.6
125
1.25
160
L
100
1.6
125
1.25
160
A-7-35
Main: Susol TS 100/160/250(Electronic)
Branch
breaker
Main breaker
TS100N/H/L
TS160N/H/L
Rating (A)
40
50
63
80
100
100
125
160
125
160
200
250
16
0.5
0.5
0.5
0.63
0.8
36
36
36
20
0.5
0.5
0.5
0.63
0.8
36
36
36
25
0.5
0.5
0.5
0.63
0.8
36
36
36
0.5
0.63
0.8
36
36
36
40
0.63
0.8
36
36
36
50
0.63
0.8
36
36
36
63
0.8
36
36
36
80
0.8
1.25
1.25
36
36
36
1.6
36
36
36
0.5
0.5
0.63
0.8
36
36
36
20
0.5
0.5
0.63
0.8
36
36
36
25
0.5
0.5
0.63
0.8
36
36
36
0.5
100
16
0.5
0.63
0.8
36
36
36
40
0.63
0.8
36
36
36
50
0.63
0.8
36
36
36
63
0.8
36
36
36
80
Trip units100
Thermal
16
magnetic
20
0.8
1.25
1.25
36
36
36
1.6
36
36
36
32
TD100 H
0.5
0.5
0.63
0.8
36
36
36
0.5
0.5
0.63
0.8
36
36
36
0.5
0.5
0.63
0.8
36
36
36
0.5
0.63
0.8
36
36
36
40
0.63
0.8
36
36
36
50
0.63
0.8
36
36
36
63
0.8
36
36
36
80
0.8
1.25
1.25
36
36
36
100
1.6
36
36
36
100
1.6
2.6
1.25
2.6
1.25
2.6
1.25
25
32
L
TS250N/H/L
32
N
Branch: Susol TD 100/160
0.5
1.25
125
160
100
TD160 H
1.6
1.25
125
160
100
L
125
160
1.6
1.25
A-7-36
Branch
breaker
TD100 H
TD160 H
A-7-37
Main breaker
Branch: Susol TS 100/160
TS400N/H/L
TS630N/H/L
TS800N/H/L
Rating (A)
300
400
500
630
800
16
20
25
32
40
50
63
80
100
16
20
25
32
40
50
63
80
Trip units100
Thermal
16
magnetic
20
25
32
40
50
63
80
100
100
125
160
100
125
160
100
125
160
Main: Susol 1000/1250/1600
Branch
breaker
TD100 H
TD160 H
Main breaker
Branch: Susol TS 100/160
TS1000L
TS1000N/H
TS1250N/H
TS1600N/H
Trip units-Electronic(Instant OFF)
Rating (A)
800
1000
800
1000
1250
1600
16
20
25
32
40
50
63
80
100
16
20
25
32
40
50
63
80
Trip units100
Thermal
16
magnetic
20
25
32
40
50
63
80
100
100
125
160
100
125
160
100
125
160
A-7-38
Branch
breaker
Main breaker
Branch: Susol TS 100/160/250
TS100N/H/L
TS160N/H/L
Rating (A)
40
50
63
80
100
100
125
160
125
160
200
250
40
0.63
0.8
2.6
50
0.63
0.8
2.6
0.8
2.6
1.25
2.6
1.6
2.6
2.6
63
80
100
TS100 H
TS250N/H/L
40
0.63
50
0.63
63
0.8
0.8
2.6
0.8
2.6
5
5
80
1.25
2.6
100
1.6
2.6
40
0.63
0.8
2.6
50
0.63
0.8
2.6
0.8
2.6
80
1.25
2.6
100
1.6
2.6
100
1.6
2.6
125
Trip units160
Thermal
100
magnetic
TS160 H
125
1.25
1.25
2.6
1.25
2.6
1.25
63
5
1.6
1.25
160
L
100
1.6
125
1.25
160
125
N
1.25
2.5
2.5
160
200
250
125
TS250 H
1.25
2.5
2.5
160
200
250
125
160
200
250
A-7-39
1.25
2.5
2.5
Branch
breaker
TS100 H
Main breaker
TS400N/H/L
TS630N/H/L
TS800N/H/L
Rating (A)
300
400
500
630
800
40
50
63
80
100
40
50
63
80
100
40
50
63
80
100
100
125
Trip units160
Thermal
100
magnetic
TS160 H
125
160
100
125
160
125
N
160
200
250
125
TS250 H
160
200
250
125
160
200
250
A-7-40
Main: TS1000/1250/1600
Branch
breaker
TS100 H
Main breaker
Branch: TS100/160/250
TS1000L
TS1000N/H
TS1250N/H
TS1600N/H
Rating (A)
800
1000
800
1000
1250
1600
40
50
63
80
100
40
50
63
80
100
40
50
63
80
100
100
125
Trip units160
Thermal
100
magnetic
TS160 H
125
160
100
125
160
125
160
200
250
125
160
200
250
125
160
200
250
TS250 H
A-7-41
Branch
breaker
N
TS400 H
L
N
TS630 H
L
N
TS800 H
L
Main breaker
TS400N/H/L
TS630N/H/L
TS800N/H/L
Rating (A)
300
400
300
400
300
400
300
400
Trip units- 500
Thermal 630
magnetic 500
630
500
630
800
800
800
500
630
800
8
8
8
8
8
8
8
T
10
T
10
T
10
10
10
10
10
10
10
8
8
8
8

Main: Susol TS 1000/1250/1600
Branch
breaker
N
TS400 H
L
Trip unitsThermal
magnetic
(TM)
TS630 H
N
L
N
TS800 H
L
N
TS1000 H
L
TS1000L
Main breaker
Rating (A)
Trip unitsElectronic
300
400
300
400
300
400
500
630
500
630
500
630
800
800
800
800
1000
800
1000
800
1000
Branch: Susol TS 400/630/800/1000/630/800(Electronic)

TS1000N/H
TS1250N/H
TS1600N/H

800
1000
800
1000
1250
1600
18
18
18
18
30
30
12
18
18
18
18
30
30
12
12
12
12
12
12
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
25
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
25
25
25
25
50
50
12
12
T
T
25
50
A-7-42
Motor protection discrimination table

Main: Susol MCCB
Branch: Susol MCCB

TD100N/H/L
Main breaker
Branch
breaker
Trip unit
Rating (A)
TD100N/H/L
FMU
TD160N/H/L
FMU
TS100N/H/L
TS160N/H/L
TS250N/H/L
TS400N/H/L
TS630N/H/L
MTU
MTU
MTU
MTU
MTU
TS100N/H/L
ETS
TS160N/H/L
TS250N/H/L
TS400N/H/L
ETS
ETS
ETS
A-7-43
16
20
25
32
40
50
63
80
100
100
125
160
100
150
220
320
500
40
80
100
150
220
320
16
20
25
Trip units-Thermal magnetic

32
40
50
63
5
80
100
6.4
6.4
6.4
8
8
8
8
TD160N/H/L
100
12.5
12.5
12.5
12.5
FMU
125
12.5
12.5
12.5
12.5
12.5
TS250N/H/L
TS100N/H/L
ATU
ETS
160
200
250
12.5
12.5
12.5
12.5
12.5
12.5
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
40
80
80
1
1
1
0.9
0.9
0.9
TS160N/H/L
TS250N/H/L
ETS
160
1.75
1.75
1.75
1.75
1.75
1.75
250
36
36
36
36
36
36
36
36
TS400N/H/L
TS630N/H/L
ETS/ETM
400
630
T
T
T
T
T
T
T
T
T
T
12.5
12.5
36
36
36
1.75
3.6
3.6
T
T
T
TS800N/H/L
ETS/ETM
630
800
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
A-7-44
MCCB
Performance: Ue=200/240V
MCCB
TD100
85kA
100kA
200kA
TS100
100kA
120kA
200kA
Motor
MC
MCCB
TOR
Contactor
Thermal overload relay
kW
Type
Rating Ir (A)
Type
Type
Setting range (A)
0.37
1.8
TD100
16
MC-9
MT-32
1.6-2.5
0.55
2.75
TD100
16
MC-32
MT-32
2.5-4
0.75
3.5
TD100
16
MC-32
MT-32
2.5-4
1.1
4.4
TD100
16
MC-40
MT-63
4-6
1.5
6.1
TD100
16
MC-40
MT-63
5-8
2.2
8.7
TD100
16
MC-40
MT-63
9-13
11.5
TD100
16
MC-40
MT-63
9-13
3.7
13.5
TD100
16
MC-40
MT-63
12-18
14.5
TD100
16
MC-40
MT-63
12-18
5.5
20
TD100
20
MC-40
MT-63
16-22
7.5
27
TD100
32
MC-40
MT-63
24-36
32
TD100
32
MC-85
MT-95
28-40
10
35
TD100
40
MC-85
MT-95
28-40
11
39
TD100
40
MC-85
MT-95
34-50
15
52
TD100
63
MC-85
MT-95
45-65
18.5
64
80
MC-85
MT-95
54-75
80
MC-85
MT-95
63-85
100
MC-85
MT-95
70-95
TD100
TS100
22
75
TD100
TS100
25
85
TD100
TS100
A-7-45
MCCB
MCCB
TD100
50kA
85kA
150kA
TS100
50kA
85kA
150kA
Motor
MCCB
kW
0.37
1.03
0.55
1.6
0.75
1.1
2.6
1.5
3.5
2.2
6.6
3.7
4
MC
TOR
Contactor
Type
Rating Ir (A)
Type
Type
Setting range (A)
TD100
16
MC-9
MT-32
1-1.6
TD100
16
MC-9
MT-32
1-1.6
TD100
16
MC-9
MT-32
1.6-2.5
TD100
16
MC-32
MT-32
2.5-4
TD100
16
MC-32
MT-32
2.5-4
TD100
16
MC-40
MT-63
4-6
TD100
16
MC-40
MT-63
5-8
7.7
TD100
16
MC-40
MT-63
6-9
8.5
TD100
16
MC-40
MT-63
7-10
5.5
11.5
TD100
16
MC-40
MT-63
9-13
7.5
15.5
TD100
16
MC-40
MT-63
12-18
18.5
TD100
20
MC-40
MT-63
16-22
10
20
TD100
20
MC-40
MT-63
16-22
11
22
TD100
25
MC-40
MT-63
16-22
15
30
TD100
32
MC-85
MT-95
24-36
18.5
37
40
MC-85
MT-95
28-40
50
MC-85
MT-95
34-50
63
MC-85
MT-95
45-65
63
MC-85
MT-95
45-65
80
MC-85
MT-95
54-75
80
MC-85
MT-95
63-85
80
MC-85
MT-95
63-85
100
MC-85
MT-95
70-95
TD100
TS100
22
44
TD100
TS100
25
52
TD100
TS100
30
60
TD100
TS100
33
68
TD100
TS100
37
72
TD100
TS100
40
79
TD100
TS100
45
85
TD100
TS100
A-7-46
MCCB
Performance: Ue=440V
MCCB
TD100
42kA
72kA
130kA
TS100
42kA
72kA
130kA
Motor
MCCB
MC
TOR
Contactor
kW
Type
Rating Ir (A)
Type
Type
Setting range (A)
0.37
0.99
TD100
16
MC-9
MT-32
0.63-1
0.55
1.36
TD100
16
MC-9
MT-32
1-1.6
0.75
1.68
TD100
16
MC-9
MT-32
1.6-2.5
1.1
2.37
TD100
16
MC-9
MT-32
1.6-2.5
1.5
3.06
TD100
16
MC-18
MT-32
2.5-4
2.2
4.42
TD100
16
MC-25
MT-32
4-6
5.57
TD100
16
MC-25
MT-32
4-6
3.7
7.1
TD100
16
MC-32
MT-32
5-8
7.9
TD100
16
MC-32
MT-32
6-9
5.5
10.4
TD100
20
MC-32
MT-32
9-13
7.5
13.7
TD100
20
MC-32
MT-32
12-18
16.9
TD100
20
MC-40
MT-63
12-18
11
20.1
TD100
25
MC-40
MT-63
16-22
15
26.5
TD100
32
MC-40
MT-63
24-36
40
MC-50
MT-63
28-40
40
MC-50
MT-63
34-50
50
MC-50
MT-63
34-50
63
MC-65
MT-95
45-65
63
MC-65
MT-95
45-65
80
MC-65
MT-95
54-75
80
MC-85
MT-95
54-75
100
MC-85
MT-95
63-85
18.5
32.8
TD100
TS100
22
39
TD100
TS100
25
45.3
TD100
TS100
30
51.5
TD100
TS100
33
58
TD100
TS100
37
64
TD100
TS100
40
67
TD100
TS100
45
76
TD100
TS100
A-7-47
MCCB
MCCB
TD100
30kA
50kA
65kA
TS100
42kA
65kA
85kA
Motor
MCCB
kW
0.37
0.55
0.75
MC
TOR
Contactor
Type
Rating Ir (A)
Type
Type
Setting range (A)
TD100
16
MC-9
MT-32
0.63-1
1.21
TD100
16
MC-9
MT-32
1-1.6
1.5
TD100
16
MC-9
MT-32
1-1.6
1.1
TD100
16
MC-9
MT-32
1.6-2.5
1.5
2.6
TD100
16
MC-32
MT-32
2.5-4
2.2
3.8
TD100
16
MC-32
MT-32
2.5-4
TD100
16
MC-40
MT-63
4-6
3.7
5.9
TD100
16
MC-40
MT-63
5-8
6.5
TD100
16
MC-40
MT-63
5-8
5.5
TD100
16
MC-40
MT-63
7-10
7.5
12
TD100
16
MC-40
MT-63
9-13
13.9
TD100
16
MC-40
MT-63
12-18
11
15
TD100
16
MC-85
MT-95
12-18
15
18.4
TD100
20
MC-85
MT-95
16-22
18.5
23
TD100
25
MC-85
MT-95
18-25
22
28.5
TD100
32
MC-85
MT-95
24-36
40
MC-85
MT-95
28-40
40
MC-85
MT-95
34-50
50
MC-85
MT-95
34-50
50
MC-85
MT-95
45-65
63
MC-85
MT-95
45-65
63
MC-85
MT-95
54-75
25
33
TD100
TS100
30
39.4
TD100
TS100
33
45
TD100
TS100
37
50
TD100
TS100
40
55
TD100
TS100
45
60
TD100
TS100
A-7-48
MCCB
N
TD100
42kA
72kA
130kA
TS100
42kA
72kA
130kA
kW
Type
Rating Ir (A)
Type
Type
0.37
0.6
TD100
16
MC-9
MT-32
0.4~0.63
0.55
0.9
TD100
16
MC-9
MT-32
0.63-1
0.75
1.1
TD100
16
MC-9
MT-32
1-1.6
1.1
1.5
TD100
16
MC-9
MT-32
1-1.6
1.5
TD100
16
MC-32
MT-32
1.6-2.5
2.2
2.8
TD100
16
MC-32
MT-32
2.5-4
Motor
MCCB
TOR
Contactor

Setting range (A)
3.8
TD100
16
MC-32
MT-32
2.5-4
3.7
4.4
TD100
16
MC-40
MT-63
4-6
4.9
TD100
16
MC-40
MT-63
4-6
5.5
6.6
TD100
16
MC-40
MT-63
5-8
7.5
8.9
TD100
16
MC-40
MT-63
7-10
10.6
TD100
16
MC-85
MT-95
9-13
11
11.5
TD100
16
MC-85
MT-95
9-13
15
14
TD100
16
MC-85
MT-95
12-18
18.5
17.3
TD100
20
MC-85
MT-95
16-22
22
21.3
TD100
25
MC-85
MT-95
18-25
25
25.4
TD100
32
MC-85
MT-95
24-36
30
30.3
TD100
32
MC-85
MT-95
24-36
33
34.6
40
MC-85
MT-95
28-40
40
MC-85
MT-95
34-50
50
MC-85
MT-95
34-50
50
MC-85
MT-95
34-50
TD100
TS100
37
39
TD100
TS100
40
42
TD100
TS100
45
44
TD100
TS100
A-7-49
MC
MCCB
Type 2 Coordination according to IEC60947-4-1]
440V - N type
Rated operational power

kW
Current[A]
440V
MCCB
Type
Contactor
Rating
Type
Thermal overload relays

Type
[A]
Setting
Short circuit
breaking capacity
range [A]
Ir[kA]
Iq[kA]
1.1
2.37
TD100N
16
MC-12b
MT-32
2.5~4
50
1.5
3.06
TD100N
16
MC-18b
MT-32
2.5~4
50
2.2
4.42
TD100N
16
MC-22b
MT-32
4~6
50
5.77
TD100N
16
MC-22b
MT-32
5~8
50
7.90
TD100N
16
MC-32a
MT-32
6~9
50
5.5
10.40
TD100N
16
MC-32a
MT-32
9~13
50
7.5
13.70
TD100N
20
MC-32a
MT-32
12~18
50
11
20.10
TD100N
32
MC-40a
MT-32
18~25
50
15
26.50
TD100N
40
MC-40a
MT-32
22~32
50
18.5
32.80
TS100N
40
MC-50a
MT-63
28~40
50
22
39.00
TS100N
50
MC-50a
MT-63
34~50
50
30
51.50
TS100N
63
MC-65a
MT-63
45~65
50
37
64.00
TS100N
80
MC-75a
MT-95
54~75
50
45
76.00
TS100N
100
MC-85a
MT-95
63~85
50
55
90.00
TS100N
100
MC-100a
MT-95
70~95
50
59
97.00
TS160N
100
MC-130a
MT-150
80~105
50
75
125
TS160N
160
MC-150a
MT-150
110~150
10
50
90
146
TS160N
160
MC-185a
MT-225
120~185
10
50
110
178
TS250N
200
MC-185a
MT-225
160~240
10
50
132
215
TS250N
250
MC-225a
MT-225
160~240
10
65
160
256
TS400N
300
MC-400a
MT-400
200~330
18
65
200
330
TS400N
400
MC-400a
MT-400
260~400
18
65
220
353
TS400N
400
MC-400a
MT-400
260~400
18
65
250
401
TS630N
500
MC-630a
MT-800
260~400
18
65
300
481
TS630N
500
MC-630a
MT-800
400~630
18
65
A-7-50
440V - H type

kW
A-7-51
Current[A]
440V
MCCB
Type
Contactor
Rating
Type

Type
[A]
Setting
Short circuit
breaking capacity
range [A]
Ir[kA]
Iq[kA]
1.1
2.37
TD100H
16
MC-12b
MT-32
2.5~4
50
1.5
3.06
TD100H
16
MC-18b
MT-32
2.5~4
50
2.2
4.42
TD100H
16
MC-22b
MT-32
4~6
50
5.77
TD100H
16
MC-22b
MT-32
5~8
50
7.90
TD100H
16
MC-32a
MT-32
6~9
50
5.5
10.40
TD100H
16
MC-32a
MT-32
9~13
50
7.5
13.70
TD100H
20
MC-32a
MT-32
12~18
70
11
20.10
TD100H
32
MC-40a
MT-32
18~25
70
15
26.50
TD100H
40
MC-40a
MT-32
22~32
70
18.5
32.80
TS100H
40
MC-50a
MT-63
28~40
70
22
39.00
TS100H
50
MC-50a
MT-63
34~50
70
30
51.50
TS100H
63
MC-65a
MT-63
45~65
70
37
64.00
TS100H
80
MC-75a
MT-95
54~75
70
45
76.00
TS100H
100
MC-85a
MT-95
63~85
70
55
90.00
TS100H
100
MC-100a
MT-95
70~95
70
59
97.00
TS160H
100
MC-130a
MT-150
80~105
70
75
125
TS160H
160
MC-150a
MT-150
110~150
10
70
90
146
TS160H
160
MC-185a
MT-225
120~185
10
70
110
178
TS250H
200
MC-185a
MT-225
160~240
10
70
132
215
TS250H
250
MC-225a
MT-225
160~240
10
70
160
256
TS400H
300
MC-400a
MT-400
200~330
18
85
200
330
TS400H
400
MC-400a
MT-400
260~400
18
85
220
353
TS400H
400
MC-400a
MT-400
260~400
18
85
250
401
TS630H
500
MC-630a
MT-800
260~400
18
85
300
481
TS630H
500
MC-630a
MT-800
400~630
18
100
440V - L type

kW
Current[A]
440V
MCCB
Type
Contactor
Rating
Type

Type
Setting
Short circuit
breaking capacity
Ir[kA]
Iq[kA]
1.1
2.37
TD100L
16
MC-12b
MT-32
2.5~4
50
1.5
3.06
TD100L
16
MC-18b
MT-32
2.5~4
50
2.2
4.42
TD100L
16
MC-22b
MT-32
4~6
50
5.77
TD100L
16
MC-22b
MT-32
5~8
50
7.90
TD100L
16
MC-32a
MT-32
6~9
50
5.5
10.40
TD100L
16
MC-32a
MT-32
9~13
50
7.5
13.70
TD100L
20
MC-32a
MT-32
12~18
100
11
20.10
TD100L
32
MC-40a
MT-32
18~25
100
15
26.50
TD100L
40
MC-40a
MT-32
22~32
100
18.5
32.80
TS100L
40
MC-50a
MT-63
28~40
130
22
39.00
TS100L
50
MC-50a
MT-63
34~50
130
30
51.50
TS100L
63
MC-65a
MT-63
45~65
130
37
64.00
TS100L
80
MC-75a
MT-95
54~75
130
45
76.00
TS100L
100
MC-85a
MT-95
63~85
130
55
90.00
TS100L
100
MC-100a
MT-95
70~95
130
59
97.00
TS160L
100
MC-130a
MT-150
80~105
130
75
125
TS160L
160
MC-150a
MT-150
110~150
10
130
[A]
range [A]
90
146
TS160L
160
MC-185a
MT-225
120~185
10
130
110
178
TS250L
200
MC-185a
MT-225
160~240
10
130
132
215
TS250L
250
MC-225a
MT-225
160~240
10
130
160
256
TS400L
300
MC-400a
MT-400
200~330
18
130
200
330
TS400L
400
MC-400a
MT-400
260~400
18
130
220
353
TS400L
400
MC-400a
MT-400
260~400
18
130
250
401
TS630L
500
MC-630a
MT-800
260~400
18
130
300
481
TS630L
500
MC-630a
MT-800
400~630
18
130
A-7-52
The purpose of calculating short circuit values
Selection of circuit breakers, fuse.
Adjusting metering devices
Consideration for mechanical resistance
Consideration for thermal resistance
Various value of short-circuit current should be
applied to the tests for upper factors.
Symmetrical current for AC and asymmetrical
current for DC are used for classifying short
circuit current.
Their differences should be essentially
considered in the basic step of making network
plan.
Symmetrical short-circuit current real value
Short-circuit current is composed of AC and
DC as it shows on <Fig.1>. The short-circuit
which indicates the real value of AC is called
as symmetrical short-current real value, l
(rms)sym. This current is the essential factor of
selecting MCCB, ACB, fuse.
AC+ DC
(asymmetrical short-circuit current)
DC
AC
3-phases average asymmetrical shortcircuit current real value: l (rms)ave

Each phase is different in its input current
value in 3 phases circuit. So that AC rate for 3
phases is different. This value is the average of
asymmetrical short-circuit current of 3 phases.
And with symmetrical short-circuit current real
value and short-circuit power factor, we can
achieve the value, and 3-phases average
asymmetrical short circuit current real value is
calculated with this formula.
l (rms)ave= l (rms)sym
Maximum asymmetrical short-circuit
current instantaneous value: lmax
Each phase has different instantaneous current
value. And when asymmetrical short-circuit
current shows its maximum instantaneous
value, the current value is called as maximum
asymmetrical short-circuit current instantaneous
value. This current is to test the mechanical
strength of serial equipments.
And with symmetrical short-circuit current real
achieve the value, and maximum asymmetrical
short-circuit current instantaneous value is
calculated with this formula.
lmax= l (rms)sym
<Fig.1> Composition of short-circuit current
Maximum asymmetrical short-circuit

current real value: l (rms)asym
The short-circuit which indicates the real value
of DC is called as asymmetrical short-circuit
current real value.
And this current value is changeable upon the
short-circuit closing phase.
This current value is treated for checking the
thermal resistant strength of wrings, CT and
etc.
With symmetrical short-circuit current real
achieve the value, from <Fig.5>.
and maximum asymmetrical short-circuit
current real value is calculated with this
formula.
l (rms)asym= l (rms)sym
A-7-53
Network impedance for calculating shortcircuit current value

Bellows should be considered for the
calculation as the impedance components
affecting circuit to trouble spot from shortcircuit power.
a. Primary part impedance of incoming
transformer Its calculated from the shortcircuit current data which is provided by
power supplier. Calculated value can be
regarded as reactance.
b. Impedance of incoming transformer Its
amount is upon the capacity of transformer
and primary voltage. Generally this
impedance can be regarded as reactance
and refer to <Table.4>, <Table.5>.
c. Reactance of motor
Motor works as generator and supply short
circuit current in the condition of an accident
circuit such as <Fig.2>.
Generation factor of firm motor should be
considered in a low voltage circuit where a
circuit breaker operates quickly and in a high
voltage circuit for the selection of fuse.
Reactance of motor can be regarded in the
range of 25% normally.
Interphase
voltage
Between RS
400V 30kW
Short-circuit
Between ST
Between TR
R current
S current
T current
d. Distribution impedance
Impedance of cable and busduct do control
short-circuit remarkably in low voltage
network. Refer to <Table.5>, <Table.6>.
<Fig.2> Short-circuit of motor
e. Others
MCCB, ACB CT are equipments for the
network of low voltage.
The impedance of these equipment which is
calculated from short-circuit current value
should be considered.
Generally, the impedance of those equipment
is that of rated current (normal condition), if
operators apply that impedance value,
bigger reactance value may be applied to
calculated short-circuit current value.
A-7-54
With percent impedance
Ohm formula (), percent impedance formula
(%), unit formula (per unit) can be applied to
calculate short-circuit current value.
]
Ohm formula [
Short-circuit current value is calculated by
converting into ohm value []
Percent impedance formula (%) Each
impedance is converted into the impedance
of base value and base voltage.
And the required amount for electric demand
should be shown as percent unit.
And apply that value in ohm formula.
Converting impedance into base value

a. Primary part impedance of transformer: %X1
PB
%X1=
100%
Q103
Q: Primary part short-circuit capacity
b. Impedance of transformer: %ZT

It generally indicates as percent impedance.
If base capacity is equal to transformer
capacity, %ZT can be used as it is. When
base capacity is not equal to transformer
capacity, convert values by this formula.
PT
PB
=
%ZT
%ZB
%: value converted by base value
Unit formula
The base value equals 1.0. and all value of
network shows in the way of decimal system.
Applying any of upper calculation formulas to
achieve short-circuit current value, it shows
equal value. To select a certain formula for
doing it, operator can select one of those
formula which is proper to oneself. Below is
percent impedance formula.
Finding base value
The rated current of transformer shall be the
base value.
Base capacity PB= PTkVA
Base voltage VB= VTV
Base current IB= IT =
Base impedance ZB=
PT
3
10A
3VT
VB2
VT2
=
3
PB10 PT103
1phase transformer should converted into

the value of 3 phase transformer, And the
percent impedance is equal to 3
2
calculated urgent value.
c. Reactance of motor: %Xm
Transformer capacity shows the value in kW,
so it is converted into unit, kVA.
(kVA value) 1.5(Output of motor, kW)
%Xm= 25% Converting it from base capacity
PB
PM
=
%Xm
%Xm
(Converting formula for different capacity)
d. Impedance of busduct, cable

Cable: Area of cross-section & length
Busduct: Rated current
In <Fig.5>, <Fig.6>
ZC = ( per each unit length)(length) []
Convert this value into % value.
%ZC =
ZC
ZB
(% converting formula)
2cables in same dimension, its recommendable

to divide the length by 2.
<Fig.3> Base value
A-7-55
Preparing a impedance map

Prepare impedance map according to the
impedance value from (2). Various electricity
suppliers like source, motor have same electric
potential in impedance map.
As you find it on <Fig.4> (a), extend it from the
unlimited bus to fault point, draw impedance
map.
In case of 1 phase short-circuit

Current value from (5) multiplied by
3
2
Each short-circuit current value (1)= 3

2
(3phases short-circuit current)(or )
Calculating impedance
Calculate impedance as <Fig.4 (b)> in
impedance map < Fig.4 (a)>
%Z = %R + j %X
%Z =
(%R)2+ (%X)2
Calculating symmetrical short-circuit

current real value
<Fig.5>
<Fig.4> Base value
Calculating various short-circuit current

value
IF (3) = IF (rms)sym (3)
=
=
P B10 3
100
3VB%Z
IB 100
A
%Z
Calculate various short-circuit current value

with , , values from <Fig.5> like
%R
short-circuit power factor cos =
%Z
3 phases average asymmetrical real value
IF (rms)ave=
IF (rms)sym
Maximum average asymmetrical real value
IF (rms)asym=IF (rms)sym
Maximum asymmetrical instantaneous value
IFmax= IF (rms)sym
A-7-56
With a simple formula
For its special cases, calculating exact value
should be needed, in the other hand, for the
practical use, we recommend simple formula.
Finding a base value
It shall be the rated current of transformer.
PB= PT [kVA]
VB= VT [V]
IB= IT [A]
VTB []
ZB=
PT103
Ref 1) Calculation in the random voltage E Voltage line
which is mostly close to E shall be selected to
calculate it .
i.e. in case of 220V, (200V line value)200/220
Ref 2) Calculation for a certain impedance Zt (%)
Impedance line which is mostly close to Zt (%)
shall be selected to calculate it.
i.e. 420V, Zt= 4.5%
%Z=4% Line value (or 5% line) 4 (or 5)/4.5
Ref 3) When the value is out of lines or over 200VA or
below 100kA, multiply 10 times to the calculated
values.
<Fig.7> Transformer capacity and short-circuit current
<Fig.6> Base value
Short-circuit current from incoming circuit

Disregard the impedance value of primary part
of transformer. Calculate short-circuit current
value according to <Fig.7>.
(If the impedance value of primary part of
transformer is considered, calculate the current
value as below formula)
IA (R)=
%X1 =
IB
(%RT)2+ (%X1+%XT)2
100
A
PB
100 [%]
Q103
If the value of %RT is not clear, %ZT%TT

IA (R) =
A-7-57
IB
100
A
%X1+%XT
Short-circuit current to motor

IA (M)= 4 (Rated current of motor)
Symmetrical short-circuit current at point A
IA= IA (R)+IA (M)
Decreasing coefficient caused by busduct
IA
Obtaining the value of
10VT
Calculate decreasing coefficient from <Fig.10>
Decreasing short-circuit current by
reactance
When theres 1phase transformer in a certain
circuit, calculate it in the base of reactance.
Regarding the reactance as pre-impedance at
source part at point of <Fig.8>,
EB
XC =
3 IC
Reactance C~D: XD[] (impedance of 1 T)
Calculating the value of XD/XC and decreasing

coefficient d from the reactance of <Fig.9>.
Current at point D ID=dIC
Impedance of 1 phase transformer XD= X (1) 1
2
a. Short-circuit current at EC voltage base
ID (rms)sym3= dIC (rms)sym3
1 phase short-circuit
(Each current)=
3
3 phases short-circuit current
2
(or
)
b. Short-circuit current at ED voltage base

ID (rms)sym3= dIC (rms)sym3EC/ED
General busduct
<Fig.9> Decreasing coefficient of short-circuit
current by reactance: d
Coefficient d for cables

ID
Calculating the value of
10VT
Decreasing coefficient b value is calculated from
<Fig.13>. For insulator drawn wrings, we can find
the value directly from <Fig.13>.
Calculating symmetrical short-circuit
current real value
IF (rms)sym= bID[D]
Busduct
Ratings
(A)
Material
Cu
Size [mm]
[/m]
Resistance Reactance Impedance

R
X
Z
[/m]
[/m]
[/m]
200
325
2.4110-4 1.31210-4 2.7410-4
400
640
0.75110-4 1.0210-4 1.26710-4
600
650
0.60710-4 0.9110-4 1.09410-4
800
675
0.41210-4 0.7210-4 0.83010-4
1000
6100
0.31510-4 0.6010-4 0.67810-4
1200
6125
0.26110-4 0.51610-4 0.57810-4
1500
6150
0.22110-4 0.44910-4 0.50010-4
2000 61252 0.12910-4 0.7910-4 0.80010-4

<Fig.10> Decreasing coefficient of general busduct (Cu)
Various short-circuit current

In case of having short-circuit current power
factor, find
,
, from <Fig.5>, If not find 3 values
from <Table.1>
3 phases short-circuit asymmetrical current
average value
IF (rms)sym
IF (rms)ave=
Maximum asymmetrical real value
IF (rms)ave=
IF (rms)sym
Maximum asymmetrical instantaneous value
IF (rms)ave=
IF (rms)sym
<Fig.11> Decreasing coefficient b in cable (600V IV)
<Table.2> , , values when short circuit power factor

value is not definite.
Symmetrical
short-circuit
real value
(A)
2500
25015000
50011000
100115000
1500125000
25000
Variables
Maximum
asymmetrical
real value
3 phases
short-circuit
asymmetrical
current
average value
Maximum
asymmetrical
instantaneous
value
1.0
1.03
1.13
1.18
1.25
1.33
1.0
1.02
1.07
1.09
1.13
1.17
1.48
1.64
1.94
2.05
2.17
2.29
<Fig.12> Decreasing coefficient b in cable (600V IV)
A-7-58
Calculation example
Calculation1) Short-circuit current value will be achieved by simple formula and percent impedance
formula for <Fig.13>
<Fig.13>
Percent impedance formula

(1) Base value
PB = 750kVA VB = 420V
IB = 1031A
ZB = 0.237
(2) Each impedance
a. Reactance at primary part of transformer
%X1=
750
100= 0.075%
1000103
b. Impedance of transformer
%RT= 1.4%
%XT= 4.8%
c. 1Tr impedance
%RT1 = 1.15750
20
1.68750
%XT1 =
20
1
= 21.6%
2
1
= 31.5%
2
d. Reactance of transformer
750
1201.5
750
%Xm2 =
1401.5
750
%Xm3 =
1001.5
750
%Xm4 =
1151.5
%Xm1 =
A-7-59
25= 104%
25= 89%
25= 125%
25= 108.7%
e. Impedance of cable
Converting impedance of whole metal
tube
[2100mm2 10m]
%RC1= 0.0001810 1 100= 0.38%
0.237
2
1
0.0001310
%XC1=
100= 0.27%
0.237
2
[125mm2 20m]
%RC2= 0.0001420 100= 1.18%
0.237
0.0001320
%XC2=
100= 1.09%
0.237
[250mm2 50m]
%RC3= 0.0000750 100= 1.47%
0.237
0.0001350
%XC3=
100= 2.74%
0.237
[14mm2 30m]
%RC4= 0.0001330 100= 16.45%
0.237
0.0001530
%XC4=
100= 1.88%
0.237
(3) Preparing a impedance map

Connect short-circuit supplier to the unlimited
bus.
IF2 (rms)sym is short-circuit current.

Therefore, convert it into 1 phase short-circuit
current.
Unlimited bus
3
IF2 (rms)1sym= 7989
= 6919
A
2
39.06
= 0.72
cos2=
54.2
<Fig.14>
Calculating impedance
Calculate it in serial/parallel type formula
(6) Various short-circuit current

Calculate , , from <Fig.5>.
a. Fault point F1
cos1= 0.422
= 1.05
= 1.3 = 1.74
IF1 (rms)ave= 1.0316900= 17407A
IF1 (rms)asym= 1.0516900= 17745A
IF1max= 1.7416900= 29406A
b. Fault point F2
cos2= 0.72
= 1.0
= 1.48
IF21 (rms)asym= 1.06919A
IF21max= 1.486919= 10240A
Simple calculation formula

(1) Base value
PB = 750kVA VB = 420V
IB = 1031A
ZB = 0.237
<Fig.15>
a. Fault point F1
b. Fault point F2
(2) Short-circuit current of incoming circuit

Disregard the impedance of primary part of
transformer
In <Fig.7> IA (R)= 20500 A
(3) Short-circuit current of motor
Sum of motor capacity=
(120+140+100+115)1.5= 713kVA
IA (M) =
713
4= 3920A
3420
%Z1=
(2.57)2+ (5.53)2
= 6.1[%]
%Z2=
(39.06)2+ (37.55)2
= 54.2[%]
(4) Symmetrical short-circuit current at point A

IA = 20500+3920= 24420A
(5) Calculation of asymmetrical short-circuit

current
a. Fault point F1
1031
IF1 (rms)sym = 6.1 100= 16900
A
2.57
= 0.422
cos1 =
6.1
b. Fault point F2 (1 phase circuit)
1031
IF2 (rms)sym =
100= 1902A (at 100V)
54.2
420
1031
=
100
= 7989A (at 420V)
54.2
100
A-7-60
Calculation example
(5) Decreasing short-circuit current for cable
a. At point F1
2100mm2 10m
2100mm2 10m= 100mm2 5m
IA 2024420
=
= 29.1
10420
10E
Coefficient b= 0.935
Short-circuit current value at point C
Ic (rms)sym= 0.93524420= 22850A
125mm2 20m
IC
2022850
=
= 108.9
10420
10E
IF1 (rms) sym= 0.785244850= 17940A
b. At point F1
14mm2 30m
IC 3024420
=
= 174.4
10420
10E
Coefficient b= 0.249
ID (rms)3sym= 0.2424420= 6080A
Decreasing by the reactance (1Tr)dp
Convert the value of %X of 1Tr to
base capacity
XD= 7502/20= 75%
Impedance of primary part at 1Tr
XA =
IB
1031
100 =
100[%]
6080
ID
Convert XD to equivalent 3 phases, and

XD/2
75026080
=
= 2.21
XA
2021031100
Coefficient d of <Fig.9> d= 0.32
IF2 (rms)3sym= 0.326080=1945
A(400V)
= 0.326080420/100
= 817 [A] (100V)
IF2 (rms)1 sym= 8171
A-7-61
3
= 7076A
2
(6) Various short-circuit current

Find ,
, from <Table.1>
a. At point F1
= 1.25 = 1.13 = 2.17

IF1 (rms)ave= 1.1317940= 20272A
IF1 (rms)asym= 1.2517940= 22425A
IF1max= 2.1717940= 38930A
b. At point F2
= 1.13
= 1.94
IF21 (rms)asym= 1.137076= 7945A
IF21max= 1.947076= 13727A
<Table.2> Comparison of short-circuit
Fault point
Symmetrical
short-circuit
current real
value
3 phases
average
asymmetrical
current real
value
Maximum
asymmetrical
current real
value
Percent impedance
calculation value
Simple formula
calculation value
Percent impedance
F1
F2
16900A 6919A
17940A 7076A
106% 102%
17407A
20272A
116%
calculation value
Simple formula
calculation value
Percent impedance
calculation value
Simple formula
calculation value
17745A 6919A
22425A 7995A
126%
115%
Short-circuit current value will be achieved by

simple formula for <Fig.16>
Z1=0.25%(1000kVA)
Short-circuit current at point B: ISB

a) Impedance Map
Serial sum of impedance
Ztot= 0.25+0.01+8= 8.26
%
A
Z2=0.01%(1000kVA)
Tr2 500kVA 6.6/3.3kV
Z3=4%
tot
= 0.25+0.01+8
= 8.26%
B
M 100kW M 200kW
Tr2 100kVA 3.3kV/220V
b) Short-circuit current ISC
Z4=2.5%
20kWu=8.5%
cos=0.8
1000kVA
Z5=1.0%
1000kVA
Z5=1.0%
M
<Fig.16>
(1) Calculate rated current at each point

Rated current InA at point A
InA=
500
kVA
1000
36.6
kV
1000
Rated current InB at point B
InB=
100
kVA
1000
33.3
kV
1000
InC=
1000kVA1000100
= 2118A
33.3kV10008.26
Breaking capacity of breaker [MVA]
MVA= 3 short-circuit current [kA]
line to line voltage[kV]
ISB=
Short-circuit current at point C: ISC

a) Impedance Map
= 43.7
A
= 17.5
A
20
kW
1000
3220
V
0.850.8
= 77.2
A
Parallel sum of impedance

Z=
(2) Put 1000k VA for base capacity and calculate

short-circuit current at each point.
Short-circuit current ISA at point A
a) Impedance Map
1
= 32.58%
1
1
1
33.26 + 2001 + 8001
b) Short-circuit current ISC

ISC=
1000
kVA1000100
= 8055A
3220V32.58%
Incoming 25%
Calculation formula
Rated current In =
Z=0.25(%)
b) Short-circuit ISA
ISA=
1000kVA1000100
36.6kV10000.25%
Transformer capacity
3Rated voltage
Short-circuit current Is =
Transformer capacity100
3Rated voltage%Z
= 34990A
Breaking capacity of breaker [MVA]

MVA= 3 short-circuit current[kA] line to
line voltage[kV]
A-7-62
Combination of transformer and impedance
<Table. 3> Combination of transformer and impedance
Transformer
3 phases transformer
Impedance
6.3kV/210V Oil Tr. 6.3kV/210V Mold Tr. 20kV/420V Mold Tr. 20kV/420V Oil Tr.
Transformer capacity (VA) ZT[%] RT[%] XT[%] ZT[%] RT[%] XT[%] ZT[%] RT[%] XT[%] ZT[%] RT[%] XT[%]
20
2.19 1.94 1.03
30
2.45 1.92 1.53 4.7
2.27 4.12
50
2.47 1.59 1.89 4.7
1.94 4.28
75
2.35 1.67 1.66 4.4
1.56 4.11
100
2.54 1.65 1.96 4.6
1.5 4.24
150
2.64 1.64 2.07 4.2
1.29
4.0
200
2.8 1.59 2.31 4.5
1.17 4.35
300
3.26 1.46 2.92 4.5
1.2 4.33
500
3.61 1.33 3.36 4.7
0.08 4.69 5.0
1.56 4.76
6.0
1.0 5.92
750
4.2 1.55
3.9 6.0
0.8 5.95 5.0
1.40 4.80
6.0
0.9 5.93
1000
5.0 1.35 4.82 7.0
0.7 6.96 5.0
1.26 4.84
6.0
0.8 5.95
1500
5.1 1.22 4.95 7.0
0.6 6.97 5.5
1.2 5.37
7.0 0.75 6.96
2000
5.0
1.2 4.85 7.5
0.65 7.47 5.5
1.1 5.39
7.0
0.7 6.96
<Table. 4> Example of transformer impedance

Transformer
Impedance
Transformer
capacity (VA)
10
20
30
50
75
100
200
300
500
750
1000
2000
3000
5000
7500
10000
15000
20000
30000
50000
75000
100000
150000
200000
300000
500000
A-7-63
1 phase transformer
6.3kV/210V Oil Tr.
6.3kV/210V Mold Tr.
ZT[%] RT[%] XT[%] ZT[%] RT[%] XT[%]
2.5
2.37
2.57
2.18
2.05
2.27
2.48
3.39
3.15
2.23
4.19
2.07
1.84
1.76
1.58
1.47
1.46
1.49
1.31
1.31
1.28
1.09
1.40
1.49
1.87
1.50
1.42
1.74
1.98
3.13
2.87
2.96
4.03
14.9
14.0
14.8
13.6
11.0
8.87
7.70
5.75
5.08
5.05
4.03
4.55
4.29
3.26
2.72
2.33
2.04
1.90
14.9
14.0
14.8
13.6
11.0
8.85
7.68
5.69
4.97
4.92
3.93
4.50
4.22
3.18
2.81
2.18
1.82
1.60
0.268
0.503
0.523
0.494
0.558
0.562
0.571
0.619
1.05
1.16
0.904
0.637
0.768
0.725
0.775
0.823
0.937
1.02
<Table. 5> Example of cable impedance

(600 vinyl cable)
Impedance of cable 1m ()
Internal
Internal
insulation
Cable
vinyl tube
dimension wiring or wiring of
cable of
steel tube
steel tube
and duct
and duct
1.6mm
2mm
3.2mm 0.00020 0.00012
5.5mm2
8mm2
14mm2
22mm2
0.00015 0.00010
30mm2
2
38mm
50mm2
60mm2
80mm2
100mm2
125mm2 0.00013 0.00009
150mm2
200mm2
250mm2
325mm2
Insulator
wiring in
building
0.00031
0.00026
0.00022
Resistance
()
/
cable
1meter
0.0089
0.0056
0.0022
0.0033
0.0023
0.0013
0.00082
0.00062
0.00048
0.00037
0.00030
0.00023
0.00018
0.00014
0.00012
0.00009
0.00007
0.00005
<Remark1> At 60Hz, the reactance multiply 2 times itself, so 1/2

reactance of primary part can achieve IB.
<Remark2> When the cable is parallelly 2 or 3ea, reactance and
resistance can be calculated in the condition of 1/3 and
1/3 length cable.
<Table.6> Impedance sample of bus and busduct (50Hz)
[10-4/m]
Ampere
rating
(A)
600
1.257
0.323
1.297
1.385
0.387
1.438
800
0.848
0.235
0.879
0.851
0.282
0.896
1000
0.641
0.185
0.667
0.645
0.222
0.682
1200
0.518
0.152
0.540
0.523
0.183
0.554
1350
0.436
0.129
0.454
0.443
0.155
0.469
1500
0.378
0.113
0.394
0.386
0.135
0.409
1600
0.360
0.107
0.375
0.367
0.128
0.389
2000
0.286
0.084
0.298
0.293
0.101
0.310
2500
0.218
0.065
0.228
0.221
0.078
0.235
3000
0.180
0.054
0.188
0.184
0.064
0.195
3500
0.143
0.042
0.149
0.146
0.051
0.155
4000
0.126
0.038
0.131
0.129
0.045
0.136
4500
0.120
0.036
0.125
0.122
0.043
0.130
5000
0.095
0.028
0.099
0.098
0.034
0.103
50Hz
60Hz
<Table.6> Impedance sample of Bus and busduct (50Hz)
[10-4/m]
Ampere
rating
(A)
600
0.974
0.380
1.045
0.977
0.456
1.078
800
0.784
0.323
0.848
0.789
0.387
0.879
1000
0.530
0.235
0.580
0.536
0.282
0.606
1200
0.405
0.185
0.445
0.412
0.222
0.468
1350
0.331
0.152
0.364
0.338
0.183
0.384
1500
0.331
0.152
0.364
0.338
0.183
0.384
1600
0.282
0.129
0.311
0.289
0.155
0.328
2000
0.235
0.107
0.259
0.241
0.128
0.273
2500
0.166
0.076
0.182
0.169
0.091
0.192
3000
0.141
0.065
0.155
0.144
0.078
0.164
3500
0.122
0.056
0.135
0.127
0.068
0.143
4000
0.110
0.051
0.121
0.113
0.061
0.126
4500
0.094
0.043
0.104
0.096
0.052
0.109
5000
0.082
0.038
0.091
0.084
0.045
0.096
5500
0.078
0.035
0.086
0.080
0.043
0.091
6500
0.068
0.028
0.074
0.071
0.031
0.077
50Hz
60Hz
A-7-64
Calculation example
Using a certain graph, you can find and
calculate the short-circuit current value which is
at one position of network. No matter the
condition of network is different, you can do the
calculation through adjusting variables.
Graph note
P coordinatesTransformer capacity (kVA)
Is 1 coordinatesShort-circuit current value
(kA)
Is 2 coordinatesShort-circuit current value
affected cable condition (kA)
Line - % impedance of transformer (%)
Line - Length of cable (m)
Line - Square mm of cable (mm2)
Line - Is2 (kA)
Remark) line shows the length of hard vinyl cable (600V IV)

(1) 3 phases transformer
Short-circuit current value at (A) where it
is just below transformer. At P coordinates,
find the coordinates value (g) of the
cross point (f) which is from transformer
capacity (e) and A line. Disregard
primary part impedance of transformer.
Find the short-circuit current value at
Point B, C which are considered cable
impedance.
At short-circuit current g (kA) of Is 1
coordinates, find the value (h) of B line
Move (h) to parallel direction of Is, and
find the cross point (i) to C line.
Move (i) to parallel direction of Is2, and
find the cross point value (j) to D line (g),
finally find (k) of Is2
Remark
1. Its not considered the transformer contribution.
Multiply 4 times the rated current of
transformer in cases.
2. The real short-circuit current value is littler
lower that its calculated value by the way we
suggest because we take the rated voltage
as AC200V, 400V. So the current value
should be calculated in the consideration of
stability
3. The calculated value is symmetrical real
value.
A-7-65
(2) 1 phase transformer

Short-circuit current value where it is just
below transformer. Find the value as
same as that of 3 phase transformer and
multiply it 3 times. (gkA)
Find the short-circuit current value where
it is considered cable impedance.
Multiply 2/3 times to g of Is coordinates
Find the Is2 value as same as that of 3
phase transformer and multiply it 3/2
times.
Memo
A-7-66
Calculation graph
(1) Short-circuit current value at point A (ISA)
At P coordinates, find (f) which is the point which is to match transformer capacity 500kVA
and A line. Then move (f) to Is1 direction and finally find (g).
ISA= 29kVA (g)
(2) Short-circuit current value at point B (ISB)
Find value h of B line (20mm) at g (= 29kA) of Is1 coordinates
Move h parallely to the direction of Is1, and find value I at the cross point with C line (200mm)
Move I parallely to the direction of Is2, and find value j at the cross point with D line (g= 29kA)
ISB= 19kA (k)
P Transformer capacity (kVA)
B length of cable
Percent impedance of transformers
A-7-67
(3) Short-circuit current value at point C (ISC)

Find Is1 coordinates value (19kA) of short-circuit current value k (= 19kA) at Point B. and find
cross point m between 19kA and B line.
Move m parallely to the direction of Is1 coordinates, and find the cross point n at C line
(30mm).
Move n parallely to the direction of Is1 and find the cross point p of Is2with D line.
Isc= 10kA (g)
Square mm of cable 600V IV

(Hard vinyl tube cable)
Is2 Short-circuit current (symmetrical real value) (KA)
A-7-68
Certifications
Type
Cerficate
Approvals
Safety certi
IEC
UL
cUL
GB
Gosstandart
CE
Europe
UL
U.S.A
cUL
U.S.A
CCC
China
GOST
Russia
Certificates
KEMA
Mark
and
name
Type
MCCB
Susol
MCCB
Susol UL
Korea
TE100S
TE100N
TD100N
TD100H
TD100L
TD160N
TD160H
TD160L
TS100N
TS100H
TS100L
TS160N
TS160H
TS160L
TS250N
TS250H
TS250L
TS400N
TS400H
TS400L
TS630N
TS630H
TS630L
TS800N
TS800H
TS800L
TS100 ETS
TS160 ETS
TS250 ETS
TS400 ETS
TS400 ETM
TS630 ETS
TS630 ETM
TS800 ETS
TS800 ETM
TS1000N
TS1250N
TS1600N
TS1000H
TS1250H
TS1600H
TS1000L
TD125NU
TD125HU
TS250NU
TS250HU
TS400NU
TS400NU
TS800NU
TS800HU
Note) : Completion
A-7-69
KEMA
Netherlands
Certifications
Approvals
Type
Mark
and
name
Type
TD
100AF
TD
160AF
TS
100AF
TS
160AF
TD100E
TD100S
TD100P
TD100N FTU
TD100N FMU
TD100H FTU
TD100H FMU
TD100L FTU
TD100L FMU
TD160E
TD160S
TD160P
TD160N FTU
TD160N FMU
TD160H FTU
TD160H FMU
TD160L FTU
TD160L FMU
TS100E
TS100E ETS
TS100S
TS100S ETS
TS100P
TS100P ETS
TS100N FTU
TS100N FMU
TS100N ETS
TS100H FTU
TS100H FMU
TS100H ETS
TS100L FTU
TS100L FMU
TS100L ETS
TS160E
TS160E ETS
TS160S
TS160S ETS
TS160P
TS160P ETS
TS160N FTU
TS160N FMU
TS160N ATU
TS160N ETS
TS160H FTU
TS160H FMU
TS160H ATU
TS160H ETS
TS160L FTU
TS160L FMU
TS160L ATU
TS160L ETS
1867
KR
Korea
LR
U.K
BV
France
ABS
U.S.A
GL
Germany
DNV
Norway
RINA
Italy
Note) : Completion
A-7-70
Marine certifications
Approvals
Type
Mark
and
name
Type
TS
250AF
TS
400AF
TS
630AF
TS250E
TS250E ETS
TS250S
TS250S ETS
TS250P
TS250P ETS
TS250N FTU
TS250N FMU
TS250N ATU
TS250N ETS
TS250H FTU
TS250H FMU
TS250H ATU
TS250H ETS
TS250L FTU
TS250L FMU
TS250L ATU
TS250L ETS
TS400E
TS400E ETS
TS400E ETM
TS400S
TS400S ETS
TS400S ETM
TS400P
TS400P ETS
TS400P ETM
TS400N FTU
TS400N FMU
TS400N ATU
TS400N ETS
TS400N ETM
TS400H FTU
TS400H FMU
TS400H ATU
TS400H ETS
TS400H ETM
TS400L FTU
TS400L FMU
TS400L ATU
TS400L ETS
TS400L ETM
TS630E
TS630E ETS
TS630E ETM
TS630S
TS630S ETS
TS630S ETM
TS630P
TS630P ETS
TS630P ETM
Note) : Completion
A-7-71
1867
KR
Korea
LR
U.K
BV
France
ABS
U.S.A
GL
Germany
DNV
Norway
RINA
Italy
Certifications
Approvals
Type
Mark
and
name
Type
TS
630AF
TS
800AF
TS630N FTU
TS630N FMU
TS630N ATU
TS630N ETS
TS630N ETM
TS630H FTU
TS630H FMU
TS630H ATU
TS630H ETS
TS630H ETM
TS630L FTU
TS630L FMU
TS630L ATU
TS630L ETS
TS630L ETM
TS800E
TS800E ETS
TS800E ETM
TS800S
TS800S ETS
TS800S ETM
TS800P
TS800P ETS
TS800P ETM
TS800N FTU
TS800N FMU
TS800N ATU
TS800N ETS
TS800N ETM
TS800H FTU
TS800H FMU
TS800H ATU
TS800H ETS
TS800H ETM
TS800L FTU
TS800L FMU
TS800L ATU
TS800L ETS
TS800L ETM
1867
KR
Korea
LR
U.K
BV
France
ABS
U.S.A
GL
Germany
DNV
Norway
RINA
Italy
Note) : Completion
A-7-72
Global Networks
LSIS global network provides

the highest quality
of products and services
Dalian, China
Dalian LSIS Co.,Ltd
Beijing, China
LSIS Beijing Office
Qingdao, China
LSIS Qingdao Office
Dubai, U.A.E.
LSIS (Middle East) FZE
Chengdu, China
LSIS Chengdu Office
Hanoi, Vietnam
LSIS-VINA Co.,Ltd
LSI Hanoi Office
LSIS (Middle East) FZE >> Dubai, U.A.E.

Address: P.O.Box-114216, API World Tower, 303B, Sheikhe Zayed Road, Dubai, U.A.E.
Tel: 971-4-332-8289 Fax: 971-4-332-9444 e-mail: hwyim@lsis.biz
Dalian LSIS Co., Ltd. >> Dalian, China

Address: No.15, Liaohexi 3-Road, Economic and Technical Development zone,
Dalian 116600, China
Tel: 86-411-8273-7777 Fax: 86-411-8730-7560 e-mail: lixk@lsis.com.cn
LSIS (Wuxi) Co., Ltd. >> Wuxi, china

Address: 102-A , National High & New Tech Industrial Development Area, Wuxi,
Jiangsu,214028, P.R.China
Tel: 86-510-8534-6666 Fax: 86-510-522-4078 e-mail: xuhg@lsis.com.cn
LSIS-VINA Co., Ltd. >> Hanoi, Vietnam

Address: Nguyen Khe - Dong Anh - Ha Noi - Viet Nam
Tel: 84-4-882-0222 Fax: 84-4-882-0220 e-mail: srjo@lsisvina.com
LSIS-VINA Co., Ltd. >> Hochiminh , Vietnam

Address: 41 Nguyen Thi Minh Khai Str. Yoco Bldg 4th Floor, Hochiminh City, Vietnam
Tel: 84-8-3822-7941 Fax: 84-8-3822-7942 e-mail: sbpark@lsisvina.com
LSIS Shanghai Office >> Shanghai, China

Address: Room E-G, 12th Floor Huamin Empire Plaza, No.726, West Yan'an Road Shanghai
200050, P.R. China
Tel: 86-21-5237-9977 (609) Fax: 89-21-5237-7191 e-mail: jinhk@lsis.com.cn
Head Office (Seoul, Korea)

Wuxi, China
LSIS (Wuxi) Co., Ltd.
Shanghai, China
LS Industrial Trading (Shanghai) Co., Ltd
LSIS Shanghai Office
Guangzhou, China
LSIS Guangzhou Office
LSIS Beijing Office >> Beijing, China

Address: B-Tower 17FL.Beijing Global Trade Center B/D. No.36, BeiSanHuanDong-Lu,
DongCheng-District, Beijing 100013, P.R. China
Tel: 86-10-5825-6025,7 Fax: 86-10-5825-6026 e-mail: cuixiaorong@lsis.com.cn
LSIS Guangzhou Office >> Guangzhou, China

Address: Room 1403,14F,New Poly Tower,2 Zhongshan Liu Road,Guangzhou, P.R. China
Tel: 86-20-8326-6764 Fax: 86-20-8326-6287 e-mail: linsz@lsis.com.cn
LSIS Chengdu Office >> Chengdu, China

Address: 12Floor, Guodong Buiding, No52 Jindun Road Chengdu, 610041, P.R. China
Tel: 86-28-8612-9151 Fax: 86-28-8612-9236 e-mail: yangcf@lsis.com.cn
LSIS Qingdao Office >> Qingdao, China

Address: 7B40,Haixin Guangchang Shenye Building B, No.9, Shandong Road Qingdao 26600, P.R. China
Tel: 86-532-8501-6568 Fax: 86-532-583-3793 e-mail: lirj@lsis.com.cn
LSIS NETHERLANDS Co.Ltd >> Netherlands

Address: 1st. Floor, Tupolevlaan 48, 1119NZ,Schiphol-Rijk, The Netherlands
Tel: 31-20-654-1420 Fax: 31-20-654-1429 e-mail: junshickp@lsis.biz
LSIS Gurgaon Office >> Gurgaon ,India

Address: 109 First Floor, Park Central, Sector-30, Gurgaon- 122 002, Haryana, India
For your safety, please read user's manual thoroughly before operating.
Contact the nearest authorized service facility for examination, repair, or adjustment.
Please contact a qualified service technician when you need maintenance.
Do not disassemble or repair by yourself!
Safety Instructions
Any maintenance and inspection shall be performed by the personnel having expertise concerned.
2006.02 LSIS Co.,Ltd. All rights reserved.
HEAD OFFICE
LS-ro 127 (Hogye-dong) dongan-gu Anyang-si
Gyeonggi-do Korea
Tel. (82-2)2034-4887, 4873, 4148
Fax. (82-2)2034-4648
www.lsis.biz
Global Network
LSIS (Middle East) FZE
Dubai, U.A.E.
Address: LOB 19 JAFZA VIEW TOWER Room 205, Jebel Ali Freezone P.O. Box 114216, Dubai, United Arab Emirates
Tel: 971-4-886 5360 Fax: 971-4-886-5361 e-mail: dhleef@lsis.biz
Dalian LSIS Co., Ltd.

Dalian, China
Address: No.15, Liaohexi 3-Road, Economic and Technical Development zone, Dalian 116600, China
Tel: 86-411-8273-7777 Fax: 86-411-8730-7560 e-mail: tangyh@lsis.com.cn
LSIS (Wuxi) Co., Ltd.

Wuxi, China
Address: 102-A , National High & New Tech Industrial Development Area, Wuxi, Jiangsu, 214028, P.R.China
Tel: 86-510-8534-6666 Fax: 86-510-522-4078 e-mail: luw@lsis.com.cn
CHEONG-JU PLANT
Cheong-Ju Plant #1, Song Jung Dong, Hung Duk Ku,
Cheong Ju, 361-720, Korea
LSIS-VINA Co., Ltd.

Hanoi, Vietnam
Address: Nguyen Khe - Dong Anh - Ha Noi - Viet Nam
Tel: 84-4-882-0222 Fax: 84-4-882-0220 e-mail: sjbaik@lsis.biz
LSIS-VINA Co., Ltd.

Hochiminh , Vietnam
Address: 41 Nguyen Thi Minh Khai Str. Yoco Bldg 4th Floor, Hochiminh City, Vietnam
Tel: 84-8-3822-7941 Fax: 84-8-3822-7942 e-mail: hjchoid@lsis.biz
LSIS Shanghai Office

Shanghai, China
Address: Room 32 floors of the Great Wall Building, No. 3000 North Zhongshan Road, Putuo District, Shanghai, China
Tel: 86-21-5237-9977 Fax: 89-21-5237-7189 e-mail: baijh@lsis.com.cn
LSIS Beijing Office

Beijing, China
Address: B-Tower 17FL.Beijing Global Trade Center B/D. No.36, BeiSanHuanDong-Lu, DongCheng-District,
Beijing 100013, P.R. China
Tel: 86-10-5825-6025,7 Fax: 86-10-5825-6026 e-mail: sunmj@lsis.com.cn
LSIS Guangzhou Office

Guangzhou, China
Address: Room 1403, 14/F, New Poly Tower, No.2 Zhongshan Liu Road, Guangzhou 510180, P.R. China
Tel: 020-8326-6754 Fax: 020-8326-6287 e-mail: chenxs@lsis.com.cn
LSIS Chengdu Office

Chengdu, China
Address: Room 1701 17Floor, huamin hanjun internationnal Building, No1 Fuxing Road Chengdu, 610016, P.R. China
Tel: 86-28-8670-3201 Fax: 86-28-8670-3203 e-mail: yangcf@lsis.com.cn
LSIS Qingdao Office

Qingdao, China
Address: Room 2001,20/F,7B40, Galaxy Building, No.29 Shandong Road, Shinan District, Qingdao 266071, P.R. China
Tel: 86-532-8501-6058 Fax: 86-532-8501-6057 e-mail: wangzy@lsis.com.cn
LSIS NETHERLANDS Co.Ltd

Schiphol-Rijk, Netherlands
Address: 1st. Floor, Tupolevlaan 48, 1119NZ,Schiphol-Rijk, The Netherlands
Tel: 31-20-654-1420 Fax: 31-20-654-1429 e-mail: junshickp@lsis.biz
Specifications in this catalog are subject to change without notice due to

continuous product development and improvement.
2013. 06
LSIS Gurgaon Office

Gurgaon, India
Address: 109 First Floor, Park Central, Sector-30, Gurgaon- 122 002, Haryana, India e-mail: hwyim@lsis.biz
Low voltage circuit breakers (E) 2006. 02/(15) 2013. 06 Printed in Korea STAFF

02.susol MCCB E 1306

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

02.susol MCCB E 1306

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

02.susol MCCB E 1306

Uploaded by

Copyright:

Available Formats

www.lsis.

Low voltage circuit breakers

New Name for LG Industrial Systems,

To advance to the next level,

Research & Development

Global technology and R&D are behind the best industrial

Quality Test at PT&T

High Voltage Test / Impulse Test

Characteristics Test / VCB Characteristics Test

Electro Technology R&D Center

Short-Circuit Test / ACB Breaker Test

Research & Development

You can count on us.

Customer satisfaction with world-class products and services:

Electric Power Industry |

Busan Plant (Korea)

Dalian Plant (China)

Wuxi Plant (China)

We also provide Total Solutions that encompass customized designs

Hanoi Plant (Vietnam)

Wuxi Plant (China)

Susol LV circuit breakers

Mounting & connection

Design for technical strong point: The Susol MCCB

SuSol Series MCCB is available forworld best breaking capacity up to

For power distribution

For protection of motor & its control device

For controlling and disconnecting circuits

Global Leading Products

Susol TE, TD, TS series

Susol circuit breakers provide superior

employing a wide variety of trip units

from 40 to 1600 amperes and in

Communication interface:RS485 (ModBUS)

The setting of communication address

Providing optimal solution

MCCB(MODBUS) CU Profibus_DP PLC EtherNET Supervision PC

Residual Current Devices

Protection against earth leakage currents

Residual Current Devices

* 3P modules may also be used on 2P circuit breakers.

Susol series circuit breakers

Optimum technical support for

TE, TD, TS series Index

Standard & Approval

Marking and configuration

Overview of trip unit

Range of LS low voltage circuit breakers

Image of circuit breaker

Range of LS low voltage circuit breakers

Main / Sub switchboard

IEC 60947-2, UL489

IEC60898, 60947-2, UL1077

Molded Case Circuit Breakers

Standards & Approval

Susol series circuit breakers and

The primary components are: a switching mechanism, an automatic tripping device