Automatic Room Light Controller

Certificate
Swami Sachchidanand Polytechnic College, (2nd Shift),

Visnagar.
TO WHOM SO EVER IT MAY CONCERN
This is to certify that PATEL PRATIK, PATEL BHAVIN, PATEL
AKASHhaving Enrollment no. 106500309501, 106500309513,
106500309543,has completed partII UDP Project work having
AUTOMATIC ROOM LIGHT CONTROLLER WITH
BIDIRECTIONAL VISITOR COUNTER.
He has undergone the process of shodh yatra , literature survey
and problem definition. He is supposed to carry out the residue UDP
PartII work on Same problem during semVI for the final full filament
of the UDP work which is prerequisite to complete Diploma
Engineering.
Date:
GuidePRAKASH G. PATEL
Electrical Engg. Dept.
Head Of Department
1
AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER
AUTOMATIC ROOM LIGHT CONTROLLER

WITH BIDIRECTIONAL VISITOR COUNTER.
PREPARED BY:
1.PATEL PRATIK J.
2.PATEL BHAVIN R.
3.PATEL AKASH B.
(106500309501)
(106500309513)
(106500309543)
2
::: AKNOWLEDGEMENT:::
The phenomenon remains same that no project ever can be executed

proficiently and efficiently without sharing the meticulous ideas, technical
expertise and innovative thought put forwarded by the technical and non
technical veterans.
It gives us pleasure in presenting this project report, undertaken by us as
per our Diploma Electrical 5th Semester Curriculum Automatic Room Light
Controller With Bidirectional Visitor Counter on having completed this project

Very first would like to thanks to the Prof.Mr. Prakash.G.PATEL H.O.D.EE DEPT. of SSPC VISHNAGAR. This project would not have been
possible without the efforts of the discrimination stood with us whenever any
difficulty came to our way and provided us grate support.
We
are
very
personally
thanks
to
our
internal
guide
is
Mr.
Prakash.G.PATEL. He has provided us a valuable guidance.

Finally, its a matter of fact that without the grace of the GOD & our
Parents, we wouldnt have been able to complete the project.
With sincere regards.
3
ABSTRACT
The fear of theft and burglary always annoys many people. When lock
and keys become less safe, one can seek the help of electronic security systems.
Such a portable security system is described here.
This electronic setup auto activated whenever the intruder enters to the
unauthorized no entry area. It auto activate the landline number and redial the last
dialed number from the conventional telephone. All we need is to do minor
changes to activate this telephone as it works as to become auto dialer circuit.
Thus whenever the intruder enters to the area, it activates the sensor circuit
of either sound activation or infrared light beam obstruction circuit, the redial
circuit become active and give a ring tone to the receiving end. It may be a mobile
phone or any landline phone or even police control room.
4
INDEX
CHAPTERCONTENTPAGE NO.
1. INTRODUCTION ..
1.1 Project Definition

1.2 Project Overview
2. BLOCKDIAGRAM AND ITS DESCRIPTION
2.1Block Diagram Description:-
3. SCHEMATIC DIAGRAM & CIRCUIT DESCRIPTION
13
3.1. Transmission Circuit

3..2. R e c e i v e r C i r c u i t
4. LIST OF COMPONENTS..
18
4.1. List of Components
5. DESCRIPTION OF COMPONENTS...
20
5.1 Description of Components
6. PROJECT FLOW CHART
27
7. PROJECT PROGRAM.
30
8. FUTURE EXPANSION.
38
9. APPLICATION, ADVANTAGES &DISADVANTAGES..
40
10. REFERENCE BOOKS & WEBSITE
42
5
CHAPTER: - 1
INTRODUCTION OF PROJECT
6
Introduction Of Project : 1.1 Project Definition:Project title is Automatic Room Light Controller
Bidirectional Visitor Counter.
With
The objective of this project is to make a controller based model to count

number of persons visiting particular room and accordingly light up the room.
Here we can use sensor and can know present number of persons.
In todays world, there is a continuous need for automatic appliances.
With the increase in standard of living, there is a sense of urgency for
developing circuits that would ease the complexity of life.
Also if at all one wants to know the number of people present in room
soaps not to have congestion, this circuit proves to be helpful.
This project "automatic room light controller with visitor
counter using microcontroller" is a reliable circuit that takes over the task of
persons/visitor in the room very accurately. When somebody enters into the
room will be switched ON and when any one. The light in room will be only
switched OFF until all the persons in the room go out. The total number of
person inside the room also displayed on the seven segment displays. The
microcontroller does the above job. it receives the signals from the sencers, and
this signal is operated under the control of software which is stored in rom.
Micron roller AT89S52 continuously monitor the
infrared receivers, when any object pass through the IR rays falling on the
receivers are obstructed this obstruction is sensed by the microcontroller.
1.2Project Overview:This Project Automatic Room Light Controller with Visitor Counter
using Microcontroller is a reliable circuit that takes over the task of controlling the room lights
as well us counting number of persons/ visitors in the room very accurately. When somebody
enters into the room then the counter is incremented by one and the light in the room will be
switched ON and when any one leaves the room then the counter is decremented by one. The
light will be only switched OFF until all the persons in the room go out. The total number of
persons inside the room is also displayed on the seven segment displays.
7
The microcontroller does the above job. It receives the signals from the sensors, and
this signal is operated under the control of software which is stored in ROM.
MicrocontrollerAT89S52 continuously monitor the Infrared Receivers, When any object pass
through the IR Receiver's then the IR Rays falling on the receiver are obstructed , this
obstruction is sensed by the Microcontroller.
8
CHAPTER :- 2
BLOCKDIAGRAM AND ITS DESCRIPTION
9
2.1 Blockdiagram:-
10
2.2Block Diagram Description:-
The basic block diagram of the bidirectional visitor counter with automatic light controller is
shown in the above figure. Mainly this block diagram consists of the following essential blocks.
1.
2.
3.
4.
Power Supply
Entry and Exit sensor circuit
AT 89S52 micro-controller
Relay driver circuit
1. Power Supply:Here we used +12V and +5V dc power supply. The main function of this block is
to provide the required amount of voltage to essential circuits. +12voltage is given. +12V is
given to relay driver. To get the +5V dc power supply we have used here IC 7805, which
provides the +5V dc regulated power supply.
2. Enter and Exit Circuits:This is one of the main parts of our project. The main intention of this block is to
sense the person. For sensing the person and light we are using the light dependent register
(LDR). By using this sensor and its related circuit diagram we can count the persons.
3. 89S52 Microcontroller:It is a low-power, high performance CMOS 8-bit microcontroller with8KB of

Flash Programmable and Erasable Read Only Memory (PEROM).
THE device is
manufactured using Atmels high-density nonvolatile memory technology and is
compatible with the MCS-51TMinstruction set and pin out. Theon-chip Flash allows the
program memory to be reprogrammed in-system or by a conventional nonvolatile memory
programmer. By combining a versatile 8-bitCPU with Flash on a monolithic hip, the Atmel
AT89S52 is a powerful.
11
4. Relay Driver Circuit:This block has the potential to drive the various controlled devices. In this block
mainly we are using the transistor and the relays. One relay driver circuit we are using to control
the light. Output signal from AT89S52 is given to the base of the transistor, which we are
further energizing the particular relay. Because of this appropriate device is selected and it do its
allotted function.
12
CHAPTER :- 3
SCHEMATIC DIAGRAM &CIRCUIT DESCRIPTION
13
CIRCUIT DESCRIPTION; There are two main parts of the circuits.

3.1.Transmission Circuit (Infrared LEDs)
3.2. Receiver Circuit (Sensors)
3.1 Transmission circuit;-
14
This circuit diagram shows

a 555 timer IC, configured to function as a basic actable multivibrator.The stabl
emultivibratorgenerates squarewave, the period of which is determined by the circu
it external to IC 555. Theastable multivibrator does not require any external trigger
to change the stateof the output. Hence the name free running oscillator. The time
during whichthe output is either high or low is determined by the two resistors and
a capacitor which are externally connected to the 555 timer.
In this circuit, a negative pulse applied at pin 2 triggers an internal flip-flop that turns
off pin 7's discharge transistor, allowing C1 to charge up throughR1. At the same time, the flipflop brings the output (pin 3) level to 'high. When capacitor C1 as charged up to about 2/3 Vcc,
the flip-flop is triggered once again, this time making the pin 3 output 'low' and turning on pin
7's discharge transistor, which discharges C1 to ground. This circuit, in effect, produces a
pulseat pin 3 whose width t is just the product of R1 and C1, i.e., t=R1C1.
IR Transmission circuit is used to generate the modulated 36
kHz IR signal. The IC555 in the transmitter side is to generate 36 kHz
square wave. Adjust the preset in the transmitter to get a 38 kHz signal at the
o/p. Then you point it over the sensor and its o/p will go low when it senses the IR
signal of 38 kHz
15
3.2 Receiver circuit:-
16
The IR transmitter will emit modulated 38 kHz IR signal and at the

receiver w e u s e
TSOP1738
(Infrared
Sensor). The
output
goes high when there is an interruption and it return back to low
a f t e r t h e t i m e p e r i o d d e t e r m i n e d b y t h e capacitor and resistor in the
circuit i.e. around 1 second. CL100 is to trigger theIC555 which is
configured as monostable multivibrator. Input is given to the Port 1of the
microcontroller. Port 0 is used for the 7-Segment display purpose. Port 2 is used
for the Relay Turn On and Turn off Purpose.LTS 542 (Common Anode)
is used for 7-Segment display and that time Relay will get voltage and triggered,
so light will get voltage and it will turn on and when counter will be 00
and at that time Relay will be turned off. Reset button will reset the
microcontroller.
17
CHAPTER: - 4
LIST OF COMPONENTS
18
LIST OF COMPONENTS
1. Microcontroller AT89S52
2. IC 7805
3. Sensor TSOP 1738 (Infrared Sensor)
4. Transformer 12-0-12, 500 mA
5. Preset 4.7K
6. Disc capacitor 104,33pF
7. Reset button switch
8. Rectifier diode IN4148
9. 9.Transistor BC 547, 2N2222
10. 7-Segment Display
19
CHAPTER: - 5
DESCRIPTION OF COMPONENTS
20
5.1 Description of Components; 1.Microcontroller AT89S52:The AT89S52 is a low-power, high-performance CMOS 8-bit microcontroller with 8K bytes
of in-system programmable Flash memory. The device is manufactured using Atmels highdensity nonvolatile memory technology and is compatible with the Industry-standard 80C51
instruction set and pin out. The on-chip Flash allows the program memory to be reprogrammed
in-system or by a conventional nonvolatile memory pro- grammar. By combining a versatile 8bit CPU with in-system programmable Flash on a monolithic chip, the Atmel AT89S52 is a
powerful microcontroller which provides a highly-flexible and cost-effective solution to many
embedded control applications.
FEATURES:1. 8 KB Reprogrammable flash.
2. 32 Programmable I/O lines.
3. 16 bit Timer/Counter3.
4. 8 Interrupt sources.
5. Power range: 4V 5.5V
6. Endurance : 1000 Writes / Erase cycles
7. Fully static operation: 0 Hz to 33 MHz
8. Three level program memory lock
9. Power off flag
10. Full duplex UART serial channel
11. Low power idle and power down modes
12. Interrupt recovery from power down modes
13. 256 KB internal RAM
14. Dual data pointer
21
2.TSOP1738 (INFRARED SENSOR)
Description:The TSOP17.. Series are miniaturized receivers for infrared remote control systems. PIN
diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter.
The demodulated output signal can directly be decoded by a microprocessor. TSOP17... is the
standard IR remote control receiver series, supporting all major transmission codes.
Features:1.
2.
3.
4.
5.
6.
7.
8.
Photo detector and preamplifier in one package

Internal filter for PCM frequency
Improved shielding against electrical field disturbance
TTL and CMOS compatibility
Output active low
Low power consumption
High immunity against ambient light
Continuous data transmission possible (up to 2400 bps)
22
3. 555 (TIMER IC):-
Description:-
The LM555 is a highly stable device for generating accurate time

delays or oscillation. Additional terminals are provided for triggering or resetting if
desired. In the time delay mode of operation, the time is precisely controlled by
one external resistor and capacitor. For actable operation as an oscillator, the free
running frequency and duty cycle are accurately controlled with two external
resistors and one capacitor. The circuit may be triggered and reset on falling
waveforms, and the output circuit can source or sink up to 200mA or drive TTL
circuits
Features:
1. Direct replacement for SE555/NE555

2.
3.
4.
5.
Timing from microseconds through hours

Operates in both as table and monostable modes
Adjustable duty cycle
Output can source or sink 200 mAOutput and supply TTL compatible
23
6. Temperature stability better than 0.005% per C

7. Normally on and normally off output
8. Available in 8-pin MSOP package
Applications:1. Precision timing
2. Pulse generation
3. Sequential timing
4. LTS 542 (7-Segment Display)Description:
The LTS 542 is a 0.52 inch digit height single digit seven-segment display. This
device utilizes Hi-eff. Red LED chips, which are made from GaAsPon Gap substrate, and has a
red face and red segment.
Features:
1. Common Anode
2. 0.52 Inch Digit Height
3. Continuous Uniform Segments
24
4. Low power Requirement

5. Excellent Characters Appearance
5 .LM7805 (Voltage Regulator):-
Description:The KA78XX/KA78XXA series of three-terminal positiveregulator are available in the TO220/D-PAK package and with several fixedoutput voltages, making them useful in a wide
range of applications. Each typeemploys internal current limiting, thermal shut down and safe
operating areaprotection, making it essentially indestructible. If adequate heat sinking
isprovided, they can deliver over 1A output current. Although designed primarily as fixed
voltage regulators, these devices can be used with external components toobtain adjustable
voltages and currents.
Features:1.
2.
3.
4.
Output Current up to 1A
Output Voltages of 5, 6, 8, 9, 10, 12, 15, 18, 24V
Thermal Overload Protection
Short Circuit Protection
25
6 RELAY CIRCUIT:-
A single pole dabble throw (SPDT) relay is connected to port RB1 of the microcontroller
through a driver transistor. The relay requires 12 volts at a current of around 100ma, which
cannot provide by the microcontroller. So the driver transistor is added. The relay is used to
operate the external solenoid forming part of a locking device or for operating any other
electrical devices. Normally there lay remains off. As soon as pin of the microcontroller
goes high, the relay operates. When the relay operates and releases. Diode D2 is the
standard diode one mechanical relay to prevent back EMF from damaging Q3 when the
relay releases.
26
CHAPTER: - 6
PROJECT FLOW CHART
27
FLOW CHART :-
28
If the sensor 1 is interrupted first then the microcontroller will look for
the sensor 2, and if it is interrupted then the microcontroller will increment
the count and switch on the relay, if it is first time interrupted.
If the sensor 2 is interrupted first then the microcontroller will look for
the sensor 1, and if it is interrupted then the microcontroller will
decrement the count.
When the last person leaves the room then counter goes to 0 and that
time the relay will turn off, and light will be turned off.
29
CHAPTER: - 7
PROJECT PROGRAM
30
INCLUDE reg_51.pdf
RB0
RB1
use
EQU
EQU
000H
008H
DIS_A EQU
DIS_B EQU
DIS_C EQU
DIS_D EQU
DIS_E EQU
DIS_F EQU
DIS_G EQU
DIS1 EQU
DIS2 EQU
P0.7
P2.6
LIGHT EQU
P2.7
SEN1 EQU
SEN2 EQU
P1.0
P1.1
; Select Register Bank 0

; Select Register Bank 1
...poke to PSW to
P0.2
P0.3
P0.4
P0.6
P0.5
P0.1
P0.0
DSEG
ORG
20H
COUNT:
DS
SPEED:
DS
VALUE_1:
DS
VALUE_2:
DS
; This is internal data memory

; Bit adressable memory
1
1
1
1
NUMB1:
NUMB2:
NUMB3:
VISITOR:
STACK DATA
1
1
1
1
DS
DS
DS
DS
3FH
CSEG
AT
0
; RESET VECTOR
;---------==========----------==========---------=========--------;
PROCESSOR INTERRUPT AND RESET VECTORS
;---------==========----------==========---------=========--------ORG
JMP
00H
MAIN
ORG
JMP
000BH
REFRESH
; Reset
;Timer Interrupt0
;---------==========----------==========---------=========--------; Main routine. Program execution starts here.

;---------==========----------==========---------=========--------MAIN:
MOV PSW,#RB0
; Select register bank 0
MOV SP,STACK
CLR LIGHT
31
MOV VISITOR,#00H
MOV SPEED,#00H
MOV COUNT,#00H
MOV VALUE_1,#15H
MOV VALUE_2,#15H
CLR DIS1
CLR DIS2
MOV TMOD,#01H
MOV TL0,#00H
MOV TH0,#0FDH
SETB ET0
SETB EA
SETB TR0
;enable timer0 for scanning
;Start the Timer
MOV VALUE_1,#00H
MOV VALUE_2,#00H
SETB SEN1
SETB SEN2
UPP: JNB SEN1,UP_COUNT
JB SEN2,UPP
MOV A,VISITOR
CJNE A,#00,UAPS
CLR LIGHT
JNB SEN2,$
CALL DELAY
JB SEN1,$
CALL DELAY
JNB SEN1,$
CALL DELAY
AJMP UPP
UAPS: DEC VISITOR
MOV A,VISITOR
CJNE A,#00,UAPA
CLR LIGHT
UAPA: MOV R2,VISITOR
MOV R1,#00H
MOV R3,#00D
MOV R4,#00D
MOV R5,#00D
MOV R6,#00D
MOV R7,#00D
CALL HEX2BCD
MOV VALUE_2,R3
MOV VALUE_1,R4
JNB SEN2,$
CALL DELAY
JB SEN1,$
CALL DELAY
JNB SEN1,$
CALL DELAY
;DOWN COUNTING
32
AJMP UPP
UP_COUNT:
SETB LIGHT
INC VISITOR
MOV A,VISITOR
CJNE A,#99,UPPS
MOV VISITOR,#98
JNB SEN1,$
CALL DELAY
JB SEN2,$
CALL DELAY
JNB SEN2,$
CALL DELAY
AJMP UPP
UPPS: MOV R2,VISITOR
MOV R1,#00H
MOV R3,#00D
MOV R4,#00D
MOV R5,#00D
MOV R6,#00D
MOV R7,#00D
CALL HEX2BCD
MOV VALUE_2,R3
MOV VALUE_1,R4
JNB SEN1,$
CALL DELAY
JB SEN2,$
CALL DELAY
JNB SEN2,$
CALL DELAY
AJMP UPP
;**************************************************
HEX2BCD:
MOV B,#10D
MOV A,R2
DIV AB
MOV
R3,B
;
MOV
B,#10
; R7,R6,R5,R4,R3
DIV
AB
MOV
R4,B
MOV
R5,A
CJNE R1,#0H,HIGH_BYTE
; CHECK FOR HIGH BYTE
SJMP ENDD
HIGH_BYTE:
ADD
MOV
A,R3
R3,B
MOV
A,#6
MOV
DIV
B,#10
AB
ADD
A,#5
33
ADD
A,R4
MOV
R4,B
ADD
A,R5
MOV
DIV
B,#10
AB
ADD
A,#2
MOV
DIV
B,#10
AB
MOV
R5,B
CJNE R6,#00D,ADD_IT
SJMP CONTINUE
ADD_IT:
ADD A,R6
CONTINUE:
MOV R6,A
DJNZ R1,HIGH_BYTE
MOV B, #10D
MOV A,R6
DIV AB
MOV R6,B
MOV R7,A
ENDD:
RET
;*********************************************************************
******
;&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&
;
7 SEGMENT DISPLAY ROUTINE
;&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&
DISP:
MOV R2,SPEED
CJNE R2,#00H,AAS1
CLR DIS_A
CLR DIS_B
CLR DIS_C
CLR DIS_D
CLR DIS_E
CLR DIS_F
SETB DIS_G
RET
AAS1: CJNE R2,#01H,AS2
CLR DIS_B
CLR DIS_C
SETB DIS_A
SETB DIS_D
SETB DIS_E
SETB DIS_F
SETB DIS_G
RET
AS2: CJNE R2,#02H,AS3
CLR DIS_A
CLR DIS_B
CLR DIS_D
CLR DIS_E
CLR DIS_G
SETB DIS_C
34
AS3:
AS4:
AS5:
AS6:
AS7:
AS8:
SETB DIS_F
RET
CJNE R2,#03H,AS4
CLR DIS_A
CLR DIS_B
CLR DIS_C
CLR DIS_D
CLR DIS_G
SETB DIS_E
SETB DIS_F
RET
CJNE R2,#04H,AS5
CLR DIS_B
CLR DIS_C
CLR DIS_F
CLR DIS_G
SETB DIS_A
SETB DIS_D
SETB DIS_E
RET
CJNE R2,#05H,AS6
CLR DIS_A
CLR DIS_C
CLR DIS_D
CLR DIS_F
CLR DIS_G
SETB DIS_B
SETB DIS_E
RET
CJNE R2,#06H,AS7
CLR DIS_A
CLR DIS_C
CLR DIS_D
CLR DIS_E
CLR DIS_F
CLR DIS_G
SETB DIS_B
RET
CJNE R2,#07H,AS8
CLR DIS_A
CLR DIS_B
CLR DIS_C
SETB DIS_D
SETB DIS_E
SETB DIS_F
SETB DIS_G
RET
CJNE R2,#08H,AS9
CLR DIS_A
CLR DIS_B
CLR DIS_C
CLR DIS_D
CLR DIS_E
CLR DIS_F
35
CLR DIS_G
RET
CLR DIS_A
CLR DIS_B
CLR DIS_C
CLR DIS_D
CLR DIS_F
CLR DIS_G
SETB DIS_E
RET
;symbol for SETB DIS_A
SETB DIS_B
SETB DIS_C
SETB DIS_D
SETB DIS_E
SETB DIS_F
CLR DIS_G
RET
;switch off all disp
SETB DIS_A
SETB DIS_B
SETB DIS_C
SETB DIS_D
SETB DIS_E
SETB DIS_F
SETB DIS_G
RET
AS12: MOV SPEED,#00H
AJMP DISP
;**********************************************************
;
INTRRUPT ROUTINE TO REFRESH THE DISPLAY
;**********************************************************
REFRESH:
PUSH
PSW
; save current registerset
MOV
PSW,#RB1
PUSH
ACC
INC COUNT
MOV R4,COUNT
QA1: CJNE R4,#01H,QA2
MOV SPEED,VALUE_1
SETB DIS1
CLR DIS2
CALL DISP
AJMP DOWN
QA2: CJNE R4,#02H,QA3
MOV SPEED,VALUE_2
CLR DIS1
SETB DIS2
CALL DISP
AJMP DOWN
QA3: MOV COUNT,#01H
MOV R4,COUNT
36
AJMP QA1
DOWN: MOV TL0,#0FFH
MOV TH0,#0F0H
POP
ACC
POP
PSW
RETI
;**********************************************************
DELAY:
MOV R1,#4FH
REP2: MOV R2,#0FFH
REP1: NOP
DJNZ R2,REP1
DJNZ R1,REP2
RET
;**********************************************************
END
37
CHAPTER:- 8
FUTURE EXPANSION
38
FUTURE EXPANSION:1. By using this circuit and proper power supply we can implement various
applications Such as fans, tube lights, etc.
2. By modifying this circuit and using two relays we can achieve a task of
opening and closing the door.
39
CHAPTER: - 9
ADVANTAGES & DISADVANTAGES & APPLICATION,
40
ADVANTAGES & DISADVANTAGES & APPLICATION,

Advantages:1. Low cost
2. Easy to use
3. Implement in single door
Disadvantages:1. It is used only when one single person cuts the rays of the sensor hence it cannot be used when two
person cross simultaneously.
Application:1. For counting purposes

2. For automatic room light control
41
CHAPTER: - 10
REFERENCE BOOKS & WEBSITE
42
Reference Books
1.
2.
3.
4.
Programming in ANSI C: E BALAGURUSAMY

The 8051microcontroller and embedded systems: MUHAMMAD ALI MAZIDI
JANICE GILLISPIE MAZIDI
The 8051 microcontroller: KENNETH J. AYALA
Website
1. www.datasheets4u.com
2. www.8051.com
43

Automatic Room Light Controller

Uploaded by

Copyright:

Available Formats

Automatic Room Light Controller

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Automatic Room Light Controller

Uploaded by

Copyright:

Available Formats

Certificate

Swami Sachchidanand Polytechnic College, (2nd Shift),

AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER

AUTOMATIC ROOM LIGHT CONTROLLER

The phenomenon remains same that no project ever can be executed

Controller With Bidirectional Visitor Counter on having completed this project

Prakash.G.PATEL. He has provided us a valuable guidance.

1.1 Project Definition

2. BLOCKDIAGRAM AND ITS DESCRIPTION

2.1Block Diagram Description:-

3. SCHEMATIC DIAGRAM & CIRCUIT DESCRIPTION

3.1. Transmission Circuit

4.1. List of Components

5.1 Description of Components

6. PROJECT FLOW CHART

9. APPLICATION, ADVANTAGES &DISADVANTAGES..

10. REFERENCE BOOKS & WEBSITE

The objective of this project is to make a controller based model to count

2.2Block Diagram Description:-

3. 89S52 Microcontroller:It is a low-power, high performance CMOS 8-bit microcontroller with8KB of

CIRCUIT DESCRIPTION; There are two main parts of the circuits.

3.1 Transmission circuit;-

This circuit diagram shows

3.2 Receiver circuit:-

The IR transmitter will emit modulated 38 kHz IR signal and at the

2.TSOP1738 (INFRARED SENSOR)

Photo detector and preamplifier in one package

3. 555 (TIMER IC):-

The LM555 is a highly stable device for generating accurate time

1. Direct replacement for SE555/NE555

Timing from microseconds through hours

AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER

6. Temperature stability better than 0.005% per C

4. LTS 542 (7-Segment Display)Description:

4. Low power Requirement

5 .LM7805 (Voltage Regulator):-

; Select Register Bank 0

; This is internal data memory

;---------==========----------==========---------=========--------; Main routine. Program execution starts here.

;enable timer0 for scanning

;Start the Timer

AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER

AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER

ADVANTAGES & DISADVANTAGES & APPLICATION,

Application:1. For counting purposes

Programming in ANSI C: E BALAGURUSAMY

You might also like