Scribd
Upload
476 views2 pages

MQ Install Instructions Autocad

The document provides instructions for installing, using, and registering Mech-Q software for various versions of AutoCAD. It explains that the correct installation file must be downloaded, how to install and find the Mech-Q menu within AutoCAD, and how to obtain an application serial number to register the software and receive an authorization code from the developer. Additional support options like service and maintenance contracts are also summarized.

Uploaded by

Roshin99
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
476 views2 pages

MQ Install Instructions Autocad

The document provides instructions for installing, using, and registering Mech-Q software for various versions of AutoCAD. It explains that the correct installation file must be downloaded, how to install and find the Mech-Q menu within AutoCAD, and how to obtain an application serial number to register the software and receive an authorization code from the developer. Additional support options like service and maintenance contracts are also summarized.

Uploaded by

Roshin99
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Mech-Q

Software

AutoCAD 14-2015 Version (Non-network)


When downloading the Mech-Q set-up file, care must be taken to ensure that you download
the correct Mech-Q set-up file corresponding to your AutoCAD version.

INSTALLING MECH-Q
For ALL AutoCAD versions and Operating Systems:

1. EXIT AutoCAD
2. Use Windows Explorer to locate the downloaded file and then double click on it to
start the program set-up.

If you can not find the file, click the Windows Start menu and select Search
(or Find) then search for the file name: "MQ*.exe"
When the Mech-Q Setup file is located, double click on it to begin the
installation process

3. Follow the instructions in the splash screens.

USING MECH-Q
After you have installed Mech-Q on your hard drive:
Start AutoCAD in the normal fashion.
If Mech-Q was installed correctly, you will note that the Mech-Q menu (pop-up and toolbars)
is now added to your existing AutoCAD menu.
Use the Mech-Q menu (toolbars or drop-down menu) to access the Mech-Q functions.

Special Notes:
Mech-Q for AutoCAD 2006-15 version
In most cases the installation and setup of Mech-Q for AutoCAD 2006-15 will not require any other steps
than those noted above. However, in some rare cases Mech-Q menu may fail to load.
If this happens, after you install Mech-Q - Start AutoCAD 2006-15 and type the following command at
the AutoCAD Command prompt: (load "MQSetupA")

ASVIC Engineering & Software


All Mail:
PO Box 1444, Cronulla NSW 2230, Australia.
Internet: www.asvic.com.au
Email: [email protected]

Telephone: 07 3303 0181 (INT + 61 7 3303 0181)

Facimile: 07 3112 5087 (INT + 61 7 3112 5087)

REGISTERING (OR AUTHORIZING) MECH-Q


When you run Mech-Q for the first time, the software generates an Application Serial Number
(ASN). The ASN must be sent to ASVIC Engineering & Software ([email protected]) so
that ASVIC can generate the Authorization Code for you to register the software.
How to find the Mech-Q Application Serial Number
You may obtain the Application Serial Number by using either of the following methods:

Use the Mech-Q Start-up dialogue or

Use About Mech-Q located under the Mech-Q Help menu or

Use Authorize Mech-Q located under the Mech-Q Maintenance menu

NOTE: Mech-Q for AutoCAD 2009-15 version


Mech-Q for AutoCAD 2009-15 (and above) versions the Mech-Q drop-down menu can be made
visible by running the AutoCAD command:
MENUBAR set the Menubar variable = 1 (ON)

To apply for an Authorization Key Code, please visit:


http://www.asvic.com.au/AuthorisationKeys.asp

Using the Authorization Key Code:


Once you receive your Mech-Q Authorization Key Code, please apply the code as follows:

1. From the Mech-Q pull down menu, select Mech-Q Register


2. Enter the Authorization Key Code EXACTLY as received (case sensitive)
3. Select the OK tab.
If the code entered is correct, the Mech-Q Registration (or Authorization) will be accepted.

Mech-Q Service & Maintenance Contract


ASVIC provides a Mech-Q Service & Maintenance Contract for periods of 12, 24 and
36 months and will include:

Upgrades from one Mech-Q product version to a newer product version (For
example: Mech-Q v3.37 to Mech-Q v3.40)
Upgrades Mech-Q from one AutoCAD version to a newer AutoCAD version.
Priority technical support

For more details, please visit: www.asvic.com.au/mqsmc.asp


ASVIC Engineering & Software
All Mail:
PO Box 1444, Cronulla NSW 2230, Australia.
Internet: www.asvic.com.au
Email: [email protected]

Telephone: 07 3303 0181 (INT + 61 7 3303 0181)

Facimile: 07 3112 5087 (INT + 61 7 3112 5087)

You might also like