Grundfos Repairing Instruction Manual

Service instructions
CR(N) 32, 45, 64 and 90

Model A
50/60 Hz
3~
1.
Type identification ........................................................................................................................... 2
1.1
1.2
1.3
Nameplate CR, CRN ........................................................................................................................................... 2

Type key .............................................................................................................................................................. 3
Codes used.......................................................................................................................................................... 3
2.
3.
Tightening torques and lubricants................................................................................................. 4

Service tools .................................................................................................................................... 5
3.1
3.2
3.3
Special tools ........................................................................................................................................................ 5

Standard tools...................................................................................................................................................... 6
Torque tools......................................................................................................................................................... 6
4.
Dismantling and assembly ............................................................................................................. 7
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
General information ............................................................................................................................................. 7

Replacement of motor ......................................................................................................................................... 8
Replacement of motor stool................................................................................................................................. 9
Replacement of coupling ..................................................................................................................................... 9
Replacement of shaft seal ................................................................................................................................. 10
Replacement of basic unit ................................................................................................................................. 11
Replacement of chamber stack ......................................................................................................................... 12
Dismantling of chamber stack............................................................................................................................ 13
Assembly of chamber stack............................................................................................................................... 15
5.
Order of assembly for chambers and impellers ......................................................................... 17
5.1
5.2
5.3
5.4
CR(N) 32............................................................................................................................................................ 17
CR(N) 45............................................................................................................................................................ 18
CR(N) 64............................................................................................................................................................ 19
CR(N) 90............................................................................................................................................................ 20
96547183 0407
GB
1 / 20
1. Type identification
This section shows the type key, the nameplate and the codes that can appear in the variant code.
Note: As codes can be combined, a code position may contain more than one code (letter).
TM02 1822 2101
1.1 Nameplate CR, CRN
Pos.
Description
Pos.
Description
Type designation
Speed
Model
Head at rated flow rate
Product number
Country of production
Place of production
Maximum pressure and temperature
Production year and week
10
Rated flow rate
2 / 20
1.2 Type key

Example
CR
64 -
3-
X-
X-
X-
X-
XXXX
Type range
Rated flow rate in m/h
Number of stages
Number of reduced-diameter impellers
Code for pump version a)
Code for pipe connection b)
Code for pump materials c)
Code for rubber components in pump d)
Code for shaft seal e)
1.3 Codes used

Note
a
Code
Description
Basic version
NEMA version
DIN flange
ANSI flange
JIS flange
Basic version
Stainless steel parts in DIN W.-Nr. 1.4401 / AISI 316
GI
Base plate and flanges in DIN W.-Nr. 1.4408 / AISI 316LN
EPDM
FKM
EUBE/V
Cartridge seal with O-ring; rotating face: tungsten carbide; stationary seat: resin-impregnated carbon; O-rings:
E=EPDM, V=FKM
EUHE/V
Cartridge seal with O-ring; rotating face: tungsten carbide; stationary seat: embedded tungsten carbide; O-rings:
E=EPDM, V=FKM
EUUE/V
Cartridge seal with O-ring; rotating face: tungsten carbide; stationary seat: tungsten carbide; O-rings: E=EPDM,
V=FKM
HUBE/V
Balanced cartridge seal; rotating face: tungsten carbide; stationary seat: resin-impregnated carbon; O-rings: E=EPDM,
V=FKM
3 / 20
2. Tightening torques and lubricants

Pos.
Description
Hexagon socket head screw
18
Air vent screw
23
25
Dim.
Torque [Nm]
M10 x 25
85
5/20
Plug
1/2
35
Lubricant
THREAD-EZE
Gardolube L 6034
THREAD-EZE
26b
M8 x 30
15
Gardolube L 6034
28
M10 x 50
62
THREAD-EZE
M8 x 20
12
Hexagon head screw
M12 x 40
40
28a
31
36
Nut
36a
Nut
M16 x 50
80
1/2 x 13 UNC
40
5/8 x 11 UNC
80
M6 x 10
M16
100
M12
40
M16
80
THREAD-EZE
Gardolube L 6034
THREAD-EZE
THREAD-EZE
48
Split cone nut
M30 x 1
70
Gardolube L 6034
58a
M10 x 25
62
THREAD-EZE
67
M8 x 16
31
Gardolube L 6034
THREAD-EZE, part no. SV9997 (0,5 l).

Gardolube L 6034, part no. SV9995 (1 l).
4 / 20
TM00 2158 1398
3. Service tools
3.1 Special tools

Pos.
Description
For pos.
Suppl. information
Part no.
CR(N) 32 ~ SV0003-3
A
Holder with pin for dismantling and assembly
Punch
CR(N) 45 ~ SV0003-4
CR(N) 64 ~ SV0003-5
SV0003
CR(N) 90 ~ SV0003-2
Holder for wear ring
Puller for bottom bearing
Hexagon socket head screw for puller
Punch for fitting of neck ring/retainer
6g-47-47c-47d-47e
49c
SV0015
CR(N) 32
SV0043
CR(N) 45
SV0044
CR(N) 64
SV0045
CR(N) 90
SV0046
6g
45a-65
Puller for wear ring
49c
Forked distance piece
105
Key for split cone nut
48-S
Pliers for retaining ring
203
5 / 20
SV0002
M8 x 50
ID6595
CR(N) 32
SV0025
CR(N) 45
SV0027
CR(N) 64
SV0028
CR(N) 90
SV0029
SV0239
985924
34 mm
SV0004
SV0047
3.2 Standard tools

Pos.
Description
Tee key
Hexagon socket head screw key
Ring/open-end spanner
Hook spanner (adjustable)
For pos.
Suppl. information
105 (113)
Part no.
M6
3 mm
SV0153
31
M6 -
5 mm
SV0124
26b-67
M8 -
6 mm
SV0050
9-58a
M10 -
8 mm
SV0051
28-58a
M10 - 8 mm
ID1205
5/8 - 1/2
SV0095
28a
1/2 - 3/8
SV0096
28a
M8 - 13 mm
SV0055
28a-36a
M12 - 19 mm
SV0054
28a
28a-36-36a
M16 - 24 mm
23-25
1/2 - 24 mm
SV0122
49-49a
SV0031
3.3 Torque tools

Pos.
O
Description
Torque wrench
Socket spanner
Socket driver for hexagon socket head screws
For pos.
R
Ratchet insert tool
Tap for key for split cone nut
Part no.
4-20 Nm
9 x 12
SV0292
20-100 Nm
9 x 12
SV0269
28a
M8 - 13 mm
SV0091
28a-36
M12 - 19 mm
SV0267
28a-36-36a
M16 - 24 mm
23-25
1/2 - 24 mm
SV0092
31
M6 - 5 mm
26b-67-E
M8 - 6 mm
SV0297
9-28-58a
M10 - 8 mm
SV0298
1/2 - 3/8
SV0094
5/8 - 1/2
SV0093
9 x 12
SV0403
28a
R
Suppl. information
O-P-Q
48-I
6 / 20
9 x 12 -> x
14
SV0296
SV0295
4. Dismantling and assembly

4.1 General information
The Grundfos centrifugal pumps, type CR(N) 32, 45, 64 and 90 are multistage in-line pumps.
If the pump is choked or damaged, please follow the instructions below.
Position numbers, see "Parts list and 3. Service tools.
Before dismantling the pump, switch off the electricity supply to the motor and close the isolating valves, if fitted, to avoid
draining the system.
The electric cable should be removed in accordance with local regulations.
Before assembly, clean and check all parts. Parts that are defective should be replaced by new parts.
Order the necessary service kits, see "Parts list".
Gaskets and O-rings should always be replaced when the pump is overhauled.
The pump should be tested according to the test specifications below:
50 Hz
60 Hz
CR(N) 32
96428962
96428971
CR(N) 45
96428972
96428973
CR(N) 64
96428974
96428975
CR(N) 90
96428976
96428977
7 / 20
4.2 Replacement of motor

4.2.1 Dismantling
Slacken the screws, (pos. 7a), and remove them together with the coupling guards, (pos. 7).
Keep the shaft seal in position on the shaft by inserting the distance piece, (pos. H), between the shaft seal, (pos. 105),
and the seal carrier, (pos. 58). See fig. 1.
105
58
TM01 1927 0698
Fig. 1
Slacken the screws, (pos. 9), and remove them together with the coupling, (pos. 8).
Slacken and remove the screws, (pos. 28a), and the nuts, (pos. 36a).
Carefully lift the motor free of the pump using lifting equipment suitable for the motor size.
TM01 1930 0698
4.2.2 Assembly
Before assembly, clean all parts.
Fit the motor and turn it to the required terminal box position.
Lubricate the screws, (pos. 28a), and the nuts, (pos. 36a), with THREAD-EZE. Fit them and tighten diagonally.
See 2. Tightening torques and lubricants.
Before fitting the coupling, check that the forked distance piece, (pos. H), is still inserted between the shaft seal,
(pos. 105), and the seal carrier, (pos. 58).
Fit the coupling, (pos. 8), on the shaft so that the top of the pump shaft is flush with the bottom of the clearance chamber
in the coupling. See fig. 2.
Fig. 2
Lubricate the hexagon socket head screws, (pos. 9). Fit the screws, tighten and leave loose.
Check that the gaps either side of the coupling halves are equal.
Tighten the hexagon socket head screws, (pos. 9), two and two (one side at a time). See 2. Tightening torques and
lubricants.
Pull the forked distance piece, (pos. H), free of the shaft, turn it and store it on the screw, (pos. 58a).
Fit the coupling guards, (pos. 7), and fasten them with the screws, (pos. 7a).
8 / 20
4.3 Replacement of motor stool

4.3.1 Dismantling
Slacken the screws, (pos. 28), and remove them together with the motor stool, (pos. 1a).
4.3.2 Assembly
Fit the motor stool, (pos. 1a), and turn it to the required position.
Lubricate the screws, (pos. 28). Fit the screws and tighten diagonally. See 2. Tightening torques and lubricants.
Lubricate the screws, (pos. 28a), and nuts, (pos. 36a). Fit them and tighten diagonally. See 2. Tightening torques and
lubricants.
lubricants.
4.4 Replacement of coupling

4.4.1 Dismantling
4.4.2 Assembly
lubricants.
9 / 20
4.5 Replacement of shaft seal

4.5.1 Dismantling
To enable replacement of shaft seal, motors up to and including 7.5 kW/10.0 HP must be removed; motors larger than
7.5 kW need not be removed.
Pumps with motors up to and including 7,5 kW/10 HP
Slacken the screws, (pos. 58a), and remove them together with the seal carrier, (pos. 58).
Clean the shaft end. Slacken the three screws, (pos. 113), so that they do not touch the shaft.
The screws should be slackened only so much that the shaft seal can be removed from the shaft.
Loosen the shaft seal, (pos. 105), from the pump head using two screwdrivers. See fig. 3, and pull it off the shaft.
105
TM01 2027 0998
113
Fig. 3
4.5.2 Assembly
Clean and smooth the shaft before fitting the shaft seal. Use the holder with emery cloth supplied with the shaft seal kit.
Apply O-ring grease to the shaft end and the O-ring of the shaft seal, (pos. 105). Press the shaft seal down on the shaft
and against the pump head.
Remove excess grease from the shaft end using a cloth.
Fit the seal carrier, (pos. 58).
Lubricate the screws, (pos. 58a). Fit the screws and tighten diagonally. See 2. Tightening torques and lubricants.
Press the pump shaft home and fasten the shaft seal on the shaft with the screws, (pos. 113). See fig. 1.
Lift the pump shaft and insert the forked distance piece, (pos. H), between the shaft seal, (pos. 105), and the seal carrier,
(pos. 58). See fig. 1.
Pumps with motors up to and including 7,5 kW/10 HP
Lubricate the screws, (pos. 28a), and the nuts, (pos. 36a). Fit them and tighten diagonally to the torque stated.
lubricants.
10 / 20
4.6 Replacement of basic unit

4.6.1 Dismantling
Slacken and remove the screws, (pos. 28).
Carefully lift the motor and the motor stool, (pos. 1a), free of the pump using lifting equipment suitable for the motor size.
Slacken the screws, (pos. 58a), and remove them together with the seal carrier, (pos. 58).
Clean the shaft end. Slacken the three screws, (pos. 113), so that they do not touch the shaft.
The screws should be slackened only so much that the shaft seal can be removed from the shaft.
Loosen the shaft seal, (pos. 105), from the pump head using two screwdrivers. See fig. 3, and pull it off the shaft.
4.6.2 Assembly
Make sure that the shaft end is clean, intact, smooth and without visible scratches.
Apply O-ring grease to the shaft end and the O-ring of the shaft seal, (pos. 105). Press the shaft seal down on the shaft
and against the pump head.
Remove excess grease from the shaft end using a cloth.
Fit the seal carrier, (pos. 58).
Lubricate the screws, (pos. 58a). Fit the screws and tighten diagonally. See 2. Tightening torques and lubricants.
Press the pump shaft home and fasten the shaft seal on the shaft with the screws, (pos. 113). See fig. 1.
Lift the pump shaft and insert the forked distance piece, (pos. H), between the shaft seal, (pos. 105), and the seal carrier,
(pos. 58). See fig. 1.
Fit the motor with motor stool, (pos. 1a), and turn it to the required terminal box position.
Lubricate the screws, (pos. 28). Fit the screws and tighten diagonally. See 2. Tightening torques and lubricants.
lubricants.
11 / 20
4.7 Replacement of chamber stack

4.7.1 Dismantling
Remove the basic unit. See 4.6 Replacement of basic unit.
Slacken the nuts, (pos. 36), and remove them together with the washers, (pos. 66a).
Knock the pump head, (pos. 2a), free of the outer sleeve, (pos. 55), by means of a rubber mallet.
Remove the pump head and the outer sleeve.
Carefully pull the chamber stack, (pos. 80), up and free of the base complete, (pos. 6b).
Remove the O-rings, (pos. 37).
4.7.2 Assembly
Apply O-ring grease to new O-rings, (pos. 37), and fit the rings in the base, (pos. 6b), and the pump head, (pos. 2a),
respectively. At the same time, replace the four rubber springs, (pos. 60), in the pump head.
Carefully fit the chamber stack into the base, (pos. 6b), and displace the straps 45 in relation to the staybolts.
Fit the outer sleeve, (pos. 55), into the base, (pos. 6b).
Fit the pump head, (pos. 2a), with the air vent screw, (pos. 18), in its previous position.
Fit the washers, (pos. 66a).
Lubricate the nuts, (pos. 36). Fit the nuts and tighten diagonally. See 2. Tightening torques and lubricants.
Continue the assembly. See 4.6 Replacement of basic unit.
12 / 20
4.8 Dismantling of chamber stack
TM01 2050 0998
Place the holder for dismantling and assembly, (pos. A), in a vice and tighten it.
Make sure that the ring fitting the inlet part, (pos. 44), is placed in the holder. See 3. Service tools.
When dismantling the chamber stack, use the holder hole marked "Dismantling". See fig. 4.
Fig. 4
Place the chamber stack so that the fixing lugs for straps on the inlet part are above the cutouts in the holder. Make sure
that the chamber stack engages with the holder.
Turn the shaft so that the hole in the shaft and the holder hole marked "Dismantling" are in the same position. Fit the
pin into the hole to hold the shaft.
Slacken the screws, (pos. 26b), and remove them together with the washers, (pos. 26c), and the straps, (pos. 26a).
Dismantle the chamber stack as follows:
Symbols refer to 5. Order of assembly for chambers and impellers.
Loosen the top chamber, (pos. 3), from the chamber/inlet part using a screwdriver.
Hold the impeller with the hook spanner, (pos. N), and slacken the split cone nut, (pos. 48), by means of the key, (pos. I).
Turn the key and knock the nut to loosen the impeller from the split cone, (pos. 49b).
Pull the split cone nut, (pos. 48), the split cone, (pos. 49b), and the impeller off the shaft.
Loosen the chamber, (pos. 4), from the chamber below or the inlet part using a screwdriver.
Loosen the chamber with bearing, (pos. 4a), from the chamber below using a screwdriver.
Loosen the bearing ring with driver, (pos. 47a), from the split cone nut, (pos. 48), using a screwdriver and pull it off the
shaft.
When the last impeller has been removed, the inlet part can be lifted off the holder.
The chamber stack is now dismantled.
13 / 20
Impeller (pos. 49/49a) and neck ring complete (pos. 45a)

If the tolerance (clearance) between the impeller (wear ring, (pos. 49c)) and the neck ring, (pos. 45), is too big, replace
the worn part(s).
TM00 7233 0996
Impeller (wear ring (pos. 49c))

If the wear ring is worn or deformed, remove it by pushing it up and free of the impeller using the holder, (pos. C), and
the puller, (pos. G). See fig. 5.
Fig. 5
Neck ring (pos. 45)

Push the neck ring retainer, (pos. 65), up and free of the cup using a screwdriver, and remove the neck ring.
Neck ring complete (pos. 45a)
If the neck ring complete is defective, push it up and free of the chamber/inlet part using two screwdrivers, and replace it.
Bearing ring with driver (pos. 47a) and stationary bearing ring (pos. 47)
The maximum permissible difference between the diameters of the bearing rings is 0.3 mm. If the difference is greater,
the worn part(s) must be replaced.
Bush (pos. 47c)
The maximum permissible difference between the diameters of the bush and the shaft is 1.0 mm. If the difference is
greater, the worn part(s) must be replaced.
Stationary bearing ring (pos. 47), bush (pos. 47c) and retaining rings (pos. 47d and 47e)
Place the chamber on a level and solid surface with the neck ring complete, (pos. 45a), uppermost.
Support the hub in the chamber. Make sure that the bearing ring, bush and retaining ring can pass freely out of the
chamber when they are pressed/knocked out of the chamber.
Stationary bearing ring (pos. 6g) and rotating bearing ring (pos. 47b)
The maximum permissible difference between the diameters of the stationary and the rotating bottom bearing ring is
0.3 mm. If the difference is greater, the worn part(s) must be replaced.
Stationary bearing ring (pos. 6g)
Slacken the screw, (pos. 31), and remove it together with the washer, (pos. 32).
Place the puller, (pos. D), underneath the bearing ring (pos. 6g).
Screw the hexagon socket head screw, (pos. E), into the puller.
Pull the puller against the bearing ring, and at the same time screw the hexagon socket head screw against the bottom
of the base.
Make sure that the hexagon socket head screw is in the centre of the bottom bearing.
Turn the hexagon socket head screw until the bearing ring is free of the base.
Rotating bearing ring (pos. 47b)
Slacken the hexagon socket head screw, (pos. 67), and remove it together with the washers, (pos. 66b and 66).
Pull the bearing ring off the shaft.
14 / 20
4.9 Assembly of chamber stack

Before assembly, clean and check all parts. Parts that are defective or do not comply with the above measurements
due to wear should be replaced by new parts.
Impeller (pos. 49 and 49a)
Press the wear ring, (pos. 49c), carefully down over the impeller skirt.
Make sure to push the ring straight down and home against the impeller skirt and take care not to damage the impeller.
TM01 1955 2201
Neck ring (pos. 45)

Place the neck ring, (pos. 45), in the cup.
Fit the neck ring retainer, (pos. 65), with the four driving dogs pointing downwards. Turn the neck ring retainer until it
engages with the neck ring.
Knock the neck ring retainer against the cup using the punch, (pos. F). See check measurements below.
Fig. 6
Pump
Nominal height X [mm]
CR(N) 32
10.1
CR(N) 45
15.5
CR(N) 64
11.5
CR(N) 90
12.1
Tolerance [mm]
0.2
It must be possible to move the neck ring freely (sideways) between the neck ring retainer and the cup.
Neck ring complete (pos. 45a)
Fit the neck ring complete and knock/press it home against the chamber/inlet part using the punch, (pos. F).
Stationary bearing ring (pos. 47), bush (pos. 47c) and retaining rings (pos. 47d and 47e)
Place the chamber on a level and solid surface with the neck ring complete, (pos. 45a), face downward.
Support the hub in the chamber. Knock/press the bearing ring/bush and retaining ring home against the chamber using
the punch, (pos. B).
Stationary bearing ring (pos. 6g)
Knock/press the bottom bearing into the base (against the shoulder) using the punch, (pos. B).
Rotating bearing ring (pos. 47b)
Fit the bearing ring (pos. 47b) to the shaft.
Fit the washers, (pos. 66 and 66b). Lubricate the hexagon socket head screw, (pos. 67) and tighten it. See 2. Tightening
torques and lubricants.
TM01 2028 0998
Chamber stack (pos. 80)

Place the holder for dismantling and assembly, (pos. A), in a vice and tighten it.
Make sure that the ring fitting the inlet part, (pos. 44), is placed in the holder.
When assembling the chamber stack, use the holder hole marked "Assembly". See fig. 7.
Fig. 7
Place the shaft in the holder.

Turn the shaft so that the hole in the shaft and the holder hole marked "Assembly" are in the same position. Fit the pin
into the hole to hold the shaft.
Fit the inlet part, (pos. 44), with neck ring complete, (pos. 45a), and turn it so that the fixing lugs for straps on the inlet
part are above the cutouts in the holder. Make sure that the inlet part engages with the holder.
15 / 20
Continue the assembly as follows:

Symbols refer to 5. Order of assembly for chambers and impellers.
Fit the impeller and the split cone, (pos. 49b).

Press the impeller home, and knock the split cone into the impeller hub using the key, (pos. I).
Hold the impeller with the hook spanner, (pos. N), and fit and tighten the split cone nut, (pos. 48). See 2. Tightening
Fit the top chamber, (pos. 3), and turn it so that the holes for straps are aligned to the fixing lugs for straps on the inlet
part.
Press the top chamber home against the chamber below or the inlet part.

Fit the chamber, (pos. 4), and press it home against the chamber below or the inlet part.

Slide the bearing ring with driver, (pos. 47a), over the split cone nut. It must engage with the split cone nut.
Fit the chamber with bearing, (pos. 4a), and press it home against the chamber below.
Fit the straps, (pos. 26a), the washers, (pos. 26c), and the screws, (pos. 26b). Lubricate the screws and tighten.
Remove the pin holding the shaft, and lift the chamber stack off the holder.
Check the impeller position. See fig. 8.
Further assembly. See 4.7.2 Assembly.
TM01 2467 2201
49
Fig. 8
Pump
Nominal height Y [mm]
CR(N) 32
70
CR(N) 45
71
CR(N) 64
70
CR(N) 90
78
16 / 20
5. Order of assembly for chambers and impellers

5.1 CR(N) 32
The assembly of the pump is illustrated in the table by symbols.
7
6
5
4
3
2
1
CR(N) 32
1-1
2-2
2-1
3-2
4-2
5-2
6-2
7-2
14
13
12
11
10
9
8
7
6
5
4
3
2
1
8-2
9-2
10-2
10
11-2
11
48
49b 49d
48
49b 49e
48
49b 49d
48
49b
49a
49
49a
49
17 / 20
12-2
12
13-2
13
14-2
4a
49e
4a
47a
47a
48
49b
48
49b
49a
49d
49
49e
14
44
TM01 1855 1000
CR(N) 32
5.2 CR(N) 45
The assembly of the pump is illustrated in the table by symbols
5
4
3
2
1
CR(N) 45
1-1
2-2
2-1
3-2
3-1
4-2
4-1
5-2
5-1
13
12
11
10
9
8
7
6
5
4
3
2
1
6-2
6-1
7-2
7-1
8-2
9-2
10-2
10
11-2
48
49b 49e
48
49b 49d
48
49b
49a
49
49a
49
12-2
4a
47a
48
49b 49d
11
49e
18 / 20
48
49b
49a
4a
12
13-2
44
47a
49d
48
49b
49
49e
TM01 1856 3701
(N) 45
5.3 CR(N) 64
2
1
1-1
CR(N) 64
2-2
2-1
8
7
6
5
4
3
2
1
3-2
3-1
4-2
4-1
5-2
5-1
6-2
6-1
7-2
48
49b 49e
48
49b 49d
48
49b
49a
49
49a
49
19 / 20
49e
48
49b
49a
8-1
4a
4a
47a
48
49b 49d
7-1
8-2
44
47a
49d
48
49b
49
49e
TM01 1857 37010
CR(N) 64
5.4 CR(N) 90
2
1
CR(N) 90
1-1
2-2
2-1
6
5
4
3
2
1
3-1
4-2
4-1
5-2
5-1
48
49b 49e
48
49b 49d
48
49b
49a
49
49a
49
20 / 20
49e
48
49b
49a
6-1
4a
47a
48
49b 49d
6-2
4a
44
47a
49d
48
49b
49
49e
TM01 1858 2201
3-2
CR(N) 90

Grundfos Repairing Instruction Manual

Uploaded by

Copyright:

Available Formats

Grundfos Repairing Instruction Manual

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Grundfos Repairing Instruction Manual

Uploaded by

Copyright:

Available Formats

Service instructions

CR(N) 32, 45, 64 and 90

Type identification ........................................................................................................................... 2

Nameplate CR, CRN ........................................................................................................................................... 2

Tightening torques and lubricants................................................................................................. 4

Special tools ........................................................................................................................................................ 5

Dismantling and assembly ............................................................................................................. 7

General information ............................................................................................................................................. 7

Order of assembly for chambers and impellers ......................................................................... 17

TM02 1822 2101

1.1 Nameplate CR, CRN

Head at rated flow rate

Maximum pressure and temperature

Production year and week

Rated flow rate

1.2 Type key

1.3 Codes used

Stainless steel parts in DIN W.-Nr. 1.4401 / AISI 316

Base plate and flanges in DIN W.-Nr. 1.4408 / AISI 316LN

2. Tightening torques and lubricants

Hexagon socket head screw

Air vent screw

Hexagon socket head screw

Hexagon socket head screw

Hexagon head screw

Hexagon socket head screw

Split cone nut

Hexagon socket head screw

Hexagon socket head screw

THREAD-EZE, part no. SV9997 (0,5 l).

TM00 2158 1398

3.1 Special tools

Holder with pin for dismantling and assembly

Holder for wear ring

Puller for bottom bearing

Hexagon socket head screw for puller

Punch for fitting of neck ring/retainer

Puller for wear ring

Forked distance piece

Key for split cone nut

Pliers for retaining ring

3.2 Standard tools

Hexagon socket head screw key

Hook spanner (adjustable)

3.3 Torque tools

Socket driver for hexagon socket head screws

Ratchet insert tool

Tap for key for split cone nut

4. Dismantling and assembly

4.2 Replacement of motor

TM01 1930 0698

4.3 Replacement of motor stool

4.4 Replacement of coupling

4.5 Replacement of shaft seal

TM01 2027 0998

4.6 Replacement of basic unit

4.7 Replacement of chamber stack

4.8 Dismantling of chamber stack

TM01 2050 0998