Modelling Structures As Systems of Springs

2007 UICEE
World Transactions on Engineering and Technology Education

Vol.6, No.1, 2007
Modelling structures as systems of springs

David C. Weggel, David M. Boyajian & Shen-En Chen
University of North Carolina at Charlotte
Charlotte, United States of America
ABSTRACT: The basic physics of a spring and elementary structural analysis principles are combined to produce a powerful
procedure to analyse static structures. Structural members are modelled as springs that are assembled in parallel and/or series
configurations to represent a structures equivalent stiffness. The overall deflection of the structure can then be computed and, after
an appropriate deconstruction of the spring system, internal member forces can be determined. This procedure is effectively
presented in some structural dynamics texts, but it is not taught when analysing or designing static structures. The authors feel that
this procedure should be taught early in a civil engineers undergraduate education to facilitate the understanding of structural
behaviour in a wider variety of structures courses. The procedure also provides an effective means to check traditional structural
analysis calculations, assists in the design of structural members and/or structural systems, and can be used to verify finite element
results.
INTRODUCTION
BASIC PHYSICS OF A SPRING
Basic physics and elementary structural analysis principles are

used to develop a straightforward but powerful procedure to
analyse static structures. The methodology is based on
modelling structural members as springs and assembling these
springs in a configuration that accurately represents the
structural system; the overall effective stiffness of the structure
can then be computed so that the overall drift (deflection) a
structure experiences when subjected to applied static loads can
be determined. This procedure, or some variant of it, is
effectively presented in some structural dynamics texts (ie [1]),
where computing the effective stiffness of a structure is
required when modelling its dynamic response with a single or
a few degrees of freedom. Further, the spring system can be
methodically deconstructed to determine the internal forces in
individual springs, which represent the internal forces in
individual structural members.
Hookes Law
The relation that describes how a linear elastic spring stretches
or compresses due to a force is presented in basic physics
texts and is known as Hookes Law; mathematically, it is given
by:
F = k
(1)
This is an equation of a straight line that passes through the

origin of its load deflection plot, where F = a tensile or
compressive force applied to the spring, k = the springs
stiffness (or spring constant), and = the deflection of the
spring. F and are both positive if the spring is subjected to a
tensile force and both negative if it is subjected to a
compressive force. Figure 1a shows an unloaded spring with
stiffness k and length L0, while Figure 1b shows a spring under
tension.
Unfortunately, this procedure is rarely used in elementary

statics-based structural analysis or design courses or presented
in textbooks (ie [2] and [3]) developed for these classes. As a
result, students are less able to link fundamental mechanics
concepts to the behaviour of complex structural systems.
Moreover, they lack an effective means of checking structural
calculations obtained from more traditional techniques.
(a) Unloaded spring
A reasonably complex building structure will be quickly and

effectively analysed in this paper after reviewing the simple
physics of a spring, developing an understanding of springs in
parallel and series, presenting stiffness representations of
common structural members, and exercising engineering
judgement in constructing spring models. While the results are
approximate due to connection and rigid member assumptions,
they can be used to check traditional structural analysis
calculations, assist in the design of structural members and/or
structural systems, and verify finite element results.
(b) Spring under tension

Figure 1: Springs before and after loading (1a-1b).
169
Figure 1b is the same spring subjected to a tensile force F,

where the loaded length L1 is greater than the unloaded length
L0 since is positive when the spring is in tension. If the
spring were to be loaded in compression, the loaded length L1
would be less than the unloaded length L0.
these springs all springs in the assemblage are arranged

parallel to one another.
Relationship to a Simple Structure

One of the simplest structural members that is not literally a
spring itself is a hanger (a structure of this type is also often
called a bar or strut) (see Figure 2).
Figure 3: n springs in parallel.

The equivalent stiffness for n springs in parallel is obtained
simply by adding together all the individual stiffnesses, thus:
k eq = k1 + k 2 + K + k n
Figure 2: Hanger (bar) under load.
Springs in Series
If an axial force F is applied at the end of the hanger, the axial

deflection of its tip can be derived using undergraduate
mechanics of material concepts, thus:
=
FL
When an assemblage of springs is subjected to a force and all

springs in general deflect by different amounts, the springs are
said to be in series. Figure 4 shows n springs in series,
where they are connected together in a chainlike fashion or in
series.
(2)
EA
(5)
where E = Youngs modulus of the material, A = cross

sectional area of the bar and L = the original (unloaded) length
of the bar. If, however, this equation is arranged to be of the
form of Hookes equation:
Figure 4: n springs in series.
F=
EA
L
(3)
The equivalent stiffness for n springs in series is:
k eq =
the equivalent stiffness of the hanger is observed to be:

k eq =
EA
L
(4)
1
1
1
1
+
+L+
k1 k 2
kn
k1 k 2 L k n
k1 + k 2 + L + k n
(6)
General Spring System

The primary point here is that the hanger can be considered as
a spring with equivalent stiffness keq = EA/L, a concept that is
rarely taught to students for application in requisite structural
analysis and design courses.
All linear elastic structures can be modelled as a system of

springs that are, in general, in parallel and/or in series with
each other. For example, in Figure 5, springs k2 and k3 are in
parallel with each other, and their equivalent stiffness is k2 + k3;
this equivalent stiffness is in series with spring k1 and the
equivalent stiffness of the entire three-spring system is:
CONCEPT OF A SPRING SYSTEM

Obviously, it is of interest to model more complex structures
than the simple hanger presented in the previous section. In
order to do so, one must be able to represent a general
structural system as an assemblage of springs in parallel and in
series. Considering the form of Hookes equation, the
equivalent stiffness of the entire system can be determined and
subsequently used to compute the deflection of the global
system (structure) in response to the applied forces.
k eq =
k1 (k 2 + k 3 )
k1 + k 2 + k 3
Springs in Parallel
When an assemblage of springs is subjected to a force and all
springs deflect by the same amount, the springs are said to be
in parallel. Figure 3 indicates why the term parallel is given to
Figure 5: Parallel-series spring system.
170
(7)
The deflection at the location of the applied load relative to the

left-end of the structure (a fixed support) can be computed by
substituting the systems equivalent stiffness into Hookes Law
and rearranging to solve for ; that is:
F ( k1 + k 2 + k 3 )
F
=
=
k eq
k1 ( k 2 + k 3 )
STRUCTURAL
MEMBERS
AND
SYSTEMS MODELLED WITH SPRINGS
and the other connection is rigid, the stiffness afforded

by the column is reduced by a factor of four (see Figure 6b);
that is:
k eq =
(8)
3EI
L3
(10)
STRUCTURAL
Additional representative spring equations are needed to model

common building structural members. These spring equations
can be derived using structural analysis principles; however,
the vast majority of students in structural analysis are probably
unaware that they have this capability.
(a) Rigid-rigid
(b) Pinned-rigid
Figure 6: Column to diaphragm connections.
Engineering Judgement
In actuality, connections are never perfectly rigid or pinned,

but structural deflections can be reasonably approximated
using these connection approximations. Finally, if both the top
and the bottom of a column is pinned (free to rotate relative to
the diaphragm to which it is connected), the stiffness provided
by the column in the lateral direction is zero; that is, the
boundary conditions of the column in this case render the
column ineffective in resisting lateral loads.
It must be emphasised early on that good engineering

judgement is required to model effectively a structure while
keeping the hand computations tractable. In order to simplify
the analysis, some structural members can be assumed to be
perfectly rigid (a spring with an infinite stiffness) with little
loss of accuracy, while the relative flexibility of other members
must be considered and, therefore, modelled as springs. Given
the applied loads and the properties of the structural elements
(ie material properties, section properties, structural
dimensions, etc), the analyst is required to carefully examine
the structural drawings (or sketches) and make assumptions
about structural connections, know how to model individual
structural components as springs, and assemble the springs in
parallel and/or series to produce a representative equivalent
stiffness so the desired structural deflections and internal
member forces can be computed.
Example: Planar Frame Building Structure

Consider the three-storey, planar-frame, building structure in
Figure 7a. It is of interest to compute the drift of the building
(deflection at roof level) given that the applied loading, the
structural geometry, and member material and section
properties are known. Due to the assumed rigid floor and roof
diaphragms, the springs representing each of the columns at a
storey level are in parallel since they are all forced to deflect
the same amount.
Rigid Members
When a structural member is very stiff relative to more flexible
structural members in its vicinity, it can often be considered to
be perfectly rigid with little resulting error. For example, floor
and roof structural systems (ie stiff floor/roof diaphragms) are
commonly considered to be rigid relative to the columns that
connect one diaphragm to another.
Flexible Members
Basic structural analysis principles allow an analyst to model a
column as a spring. A column that is rigidly connected to a
rigid diaphragm the ends of the column do not rotate relative
to the diaphragm at its base and top, has an equivalent lateral
stiffness (see Figure 6a) given by:
k eq =
12 EI
L3
(9)
(b) Equivalent spring
where I = a section property of the column known as the

moment of inertia and L = the length of the column. This
equation represents the stiffness due to bending in the column
and is used when the top of the column displaces laterally
relative to its base.
Figure 7: Hypothetical 2D building example (7a-7b).

All five columns of the first storey have flexural rigidity 2
and equal lengths as shown in Figure 7a; individual stiffnesses
are different, however, due to the different end (boundary)
conditions. Since all five springs are in parallel, the first-storey
stiffness is:
However, if either the top or bottom of the column is perfectly

free to rotate relative to the diaphragm a pinned-connection
171
k1 = 2
12(2 E I )
( 4l )
+ 3
3(2 E I )
( 4l )
66 E I
4 l3
computed, it is equal to F times the percentage of the stiffness

this column possesses relative to the total storey stiffness; the
force in this column is:
48 E I 18 E I
+
4 l3
4 l3
(11)
FL1 =
Similarly, the second-storey springs are all in parallel and the

storey stiffness is:
k2 = 0 + 2
3(1.5 E I )
l
12(1.5 E I )
l
9E I
l
k L1 =
l3
(12)
l3
12 E I
l
15 E I
l3
1
4392l 3
26,730 E I
26,730 E I
4392l 3
F
4392Fl 3
=
k eq 26,730 E I
(17)
(18)
24
12
F=
F
66
33
(19)
or approximately one third of the storey force F.
(13)
CONCLUSIONS
Modelling linear elastic structures as a system of springs
enhances the understanding of structural behaviour. The
procedure also provides a quick and effective means to check
traditional structural analysis calculations, assists in the design
of structural members and/or structural systems, and can be
used to verify finite element results.
This modelling procedure, or some variation of it, is effectively
presented in some structural dynamics texts for computing a
structures equivalent stiffness but, unfortunately, it is rarely
used in elementary statics-based structural analysis or design
courses. The authors feel that this procedure, if taught early in
a civil engineers undergraduate education, will facilitate the
understanding of structural behaviour in a wider variety of
structures courses.
(14)
Thus, rearranging Hookes Law, the drift is given by the

following equation:
24 E I
4 l3
66 E I
4 l3
FL1 =
1
1
=
3
1
1
1
4l
l3
l3
+
+
+
+
k1 k 2 k 3
66 E I 27 E I 15E I
so:
Since each storey is in series relative to its neighbouring storey,

the equivalent stiffness of the entire structure, shown
schematically in Figure 7b, is given by:
k eq =
( 4l )
3
k1 =
The third-storey stiffness is:
3E I
12(2 E I )
and:
The left-most column of the second-storey has zero stiffness

since both ends of the column are pinned.
k3 = 0 +
(16)
where kL1 is the stiffness of the leftmost column of the first

storey and k1 is the total first storey stiffness, and:
18 E I
27 E I
k L1
F
k1
REFERENCES
(15)
1.
Internal forces in any column at each storey can be computed

by proportion of the individual column stiffness relative to the
overall stiffness at the storey. For example, for the load case
shown in Figure 7, the force at any storey level is F. If the
lateral force in the leftmost column of the first storey is to be
2.
3.
172
Tedesco, J.W., McDougal, W.G. and Ross, C.A.,

Structural Dynamics: Theory and Applications. Menlo
Park: Addison-Wesley (1999).
Leet, K.M. and Uang, C-M., Fundamentals of Structural
Analysis (2nd edn). Boston: McGraw-Hill (2005).
Hibbeler, R.C., Mechanics of Materials (4th edn). Upper
Saddle River: Prentice Hall (2000).

Modelling Structures As Systems of Springs

Uploaded by

Copyright:

Available Formats

Modelling Structures As Systems of Springs

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Modelling Structures As Systems of Springs

Uploaded by

Copyright:

Available Formats

2007 UICEE

World Transactions on Engineering and Technology Education

Modelling structures as systems of springs

BASIC PHYSICS OF A SPRING

Basic physics and elementary structural analysis principles are

This is an equation of a straight line that passes through the

Unfortunately, this procedure is rarely used in elementary

(a) Unloaded spring

A reasonably complex building structure will be quickly and

(b) Spring under tension

Figure 1b is the same spring subjected to a tensile force F,

these springs all springs in the assemblage are arranged

Relationship to a Simple Structure

Figure 3: n springs in parallel.

Figure 2: Hanger (bar) under load.

If an axial force F is applied at the end of the hanger, the axial

When an assemblage of springs is subjected to a force and all

where E = Youngs modulus of the material, A = cross

The equivalent stiffness for n springs in series is:

the equivalent stiffness of the hanger is observed to be:

General Spring System

All linear elastic structures can be modelled as a system of

CONCEPT OF A SPRING SYSTEM

Figure 5: Parallel-series spring system.

The deflection at the location of the applied load relative to the

and the other connection is rigid, the stiffness afforded

Additional representative spring equations are needed to model

Figure 6: Column to diaphragm connections.

In actuality, connections are never perfectly rigid or pinned,

It must be emphasised early on that good engineering

Example: Planar Frame Building Structure

where I = a section property of the column known as the

Figure 7: Hypothetical 2D building example (7a-7b).

However, if either the top or bottom of the column is perfectly

computed, it is equal to F times the percentage of the stiffness

Similarly, the second-storey springs are all in parallel and the

or approximately one third of the storey force F.

Thus, rearranging Hookes Law, the drift is given by the

Since each storey is in series relative to its neighbouring storey,

The third-storey stiffness is:

The left-most column of the second-storey has zero stiffness

where kL1 is the stiffness of the leftmost column of the first

Internal forces in any column at each storey can be computed

Tedesco, J.W., McDougal, W.G. and Ross, C.A.,

You might also like