Boiler Annex

ANNEXURE- I
TECHNICAL SPECIFICATIONS, SCOPE, PERFORMANCE PARAMETERS,

BATTERY LIMITS , EXCLUSIONS OF
2x 65 TPH 80 ATA, 515 +/- 5 Deg C, Imported COAL FIRED BOILER
-1-
1. SCOPE AND EXTENT OF SERVICES, TECHNICAL SPECIFICATIONS AND

EQUIPMENT TO BE ERECTED AND COMMISSIONED
DESIGN BASIS
Type
Atmospheric Fluidised
Bed Combustion
Steam Parameters:
Maximum continuous rating (MCR) *
Pressure at outlet of main steam stop
valve and NRV
Temperature at superheater outlet
Temperature control range
No of boilers
Unit
TPH
Ata
C
% MCR
No
o
65
80
515 5
60-110
2
Feed water
Source
Mixture of condensate and DM water
Temperature at inlet of deaerator

(DM water + return condensate)
Temperature at inlet of
economiser
27
102
Boiler shall be capable of operating with an output of 10% above the MCR for a
period of 30 minutes, once in every 8 hours. This peaking requirement should
not affect the circulation ratio of the system.
Note :
*
The specified maximum continuous rating shall be the gross output at main
steam stop valve excluding any auxiliary steam requirement of the boiler.
Vendor shall specify the quality of water required at the inlet of deaerator
(DM water)
-2-
2. DESIGN CRITERIA OF BOILER

2.1
Main Fuel
Imported Coal
2.2
Firing Capability of Boiler on selected Fuels
As highlighted above, PURCHASER desires to burn Imported Coal, , the

characteristics of which are given in clause 2.3.4. Boiler shall, therefore, have
burning capability on the selected fuels, at least, but not limited to that specified
below:
Fuel
Proportion on MCR %
Imported coal
2.3
100
Feeding Arrangement
Fuel shall be fed as underfeed during non-monsoon period. Supplier shall

highlight the feeding system selected with justification.
Note :
Hence boiler shall be capable of burning Coal without any supporting fuel during
under feed system which shall generally be adopted for feeding coal into the
boiler.
-3-
2.4
Typical Characteristics of Fuels
Typical characteristics of fuel proposed for the boilers are given below in detail
Imported Coal
Carbon
30-50
Sulphur ADB
0.7-0. 9
Moisture(ARB)
10-20
Ash ADB
8-20
GCV
kcal/kg
5800- 6500
For the performance evaluation the GCV shall be 6300 Kcal/Kg.
3.0
ERECTION AND COMMISSIONING ASISTANCE BY THE VENDOR

The Vendor shall be responsible for the erection and commissioning of the
Equipment supplied by them and all other items, which are part of the system.
The Vendor shall be responsible for all aspects of the erection and commissioning
of
the
2 x 65 tph power boiler.
Complete Design & Engineering of the Boiler & ESP including the items in
Jubilant scope of work shall be in VENDOR Scope. VENDOR shall submit 3 sets
of drawing for the review/ comments and shall submit 3 approved drawings for
Construction along with soft copy.
Boiler pressure parts consisting of

Steam drum
Furnace and headers
Super heaters
Attemperator
Economiser
Protection shields for first row of economizer top/bottom banks shall be

provided with baffle plates for the bends.
Mountings and fittings
-4-
Fluidized bed combustion system of underfeeding systems
Coal bunker of 24 hrs storage capacity hopper with 2 mm SS lining for

conical portion. Top chequered plate and cross beams to support the
conveyors above .
Rod gate damper below all bunkers
Solid fuel firing equipment
Feed Chutes at inlet of Fuel feeders
Fuel Feeders
Fuel Feeder discharge chutes
Dedicated VFDs for Fuel Feeders
Start-up fuel system
Fuel oil tank of Suitable Capacity
Surge hoppers below fuel bunkers
Provision for under bed firing of the Bio-Gas
Water cooled bed ash coolers
Electro Static Precipitator (ESP) , EMIGI Rapper type
ESP inlet/outlet expansion bellows
Ash door assemblies.
Air and flue gas fans and draught system
Two (2) Forced Draught (FD) fans (2 x 60%)
Two (2) Induced Draught (ID) fans (2 x 60%)
Two primary air fans (2 x 125%)
On line O2 analyser
Higher size fuel transport line, castings & PA Fan with Motor
2 nos water cooled bed ash cooler as against 6 nos air cooled bed ash cooler
Motorized Valve as against manual valve at each feed pump discharge
All Blowdown second valve should be lever operated
-5-
Pneumatically operated bypass valve for FCV as against Motorized bypass

valve for Boiler feed water control station
2 nos Bi-colour Multi-port direct water level gauges & 1 No hydrastep

(Electronic drum level indicator) to indicate the remote water level indication
at operating Floor & Control room.- Yarway control
Hydraulic type HP dosing pump and LP dosing pump
Silencer for FD Fan suction
SA213 T22 material for radiant superheater All coal feeders shall be designed
such that boiler performance (100 % MCR) should not affect during one
feeder down condition.
ESP to meet the outlet dust emission level of 50 mg/ Nm3 considering worst
coal as basis (i.e. Coal of 5800 Kcal/Kg GCV) with all field in Service.
Boiler MCC (Considering 2 x 60 %ID, FD fans, 2 x 125 % PA Fan, 2x 120 %

feed Pump, Coal Feeders, LP/ HP Dosing etc). The MCC shall be as per the
specifications as enclosed
ESP MCC
Draught gauges for Air Box compartments with panel
Headless type RTD with 10 mtr Teflon Insulated Cables instead of Head
mounted RTD
Flow switches in sealing water line of Feed pumps
Proximity switches for Control Valves, RPC & SOPC
Additional 1 no Furnace Pressure Transmitter
Level transmitter instead of level switch in Deaerator
Additional 1 no Drum Pressure Transmitter
High level switches for ESP, Air Heater & Economisers ash hoppers
SS316 of material for all impulse piping
Flame proof cable glands instead of Industrial area Cable Glands.
ESP hopper Heaters
Complete Structure, GI Grating, Platform, railing, tie beams, supports, Ash

Hoppers for the ESP. the ESP Hopper capacity should be for 8 hrs storage.
Air & Flue Gas Ducting
All Dampers & expansion bellows

-6-
PA/SA fan suction
From PA/SA fan discharge up to air heater inlet
From Air heater outlet up to wind box
From furnace outlet up to economiser inlet
From economiser outlet to air heater
All Control dampers & control valves to be provided with smart valve
positioners, position feed back transmitter & pnp type proximity switches to
close limit with desired state under fail safe condition.
Root valves for all HP Valves
Air Heater arrangement (Air through tubes)
Gauge glasses 2 nos near drum, one no hydrastep in control room ( Yarway
control) / Operating floor and 1 electronic level indication in Control room
Access Door assemblies
HP dosing system consisting of dosing tanks, associated pumps, motors,

piping & valves
LP dosing system consisting of dosing tanks, associated pumps, motors,

piping & valves
De-aerator cum feed water storage tank
Sample coolers, blow down tanks & flash vessels
Feed pumps (electrical) 2 x 120 % MCR capacity along with all valves ,
including imported ARC valves.
Feed pump manual suction and motorized discharge isolation valves
Boiler platform and structure extension of 3000 mm on one side of the boiler
and side cladding up to operating floor
Boiler house, fuel bunkers, all structural, operating platforms, roofs and side
cladding with metapoly
Feed water control stations

- 1 x 100% pneumatic valve
- 1 x 30% pneumatic valve
- 1 x 100% pneumatic bypass valve with leakage class VI
All auxiliaries like common frames, coupling set and foundation bolts for
pumps, motors
Boiler structural and foundation bolts

-7-
Boiler house front row columns shall be supplied to take the load of both coal
conveyors. However, other row of columns and other structures for
conveyor supports shall be under Purchasers scope. Since coal conveyors
shall be located on the front side of the boilers and the first row columns
shall take the load of all the conveyors, first row of columns of second boiler
shall also be erected along with the first boiler to erect coal conveyors.
All the horizontal beams below the chequered plate of the fuel bunkers to take
care of the loading of all the fuel conveyors (which are under Purchasers
scope.)
Refractory and insulation
Continuous blow down (CBD) tank
Intermittent blow down (IBD) tank
Steam, water, instrument air, cooling water and auxiliary pipe work with
valves and fittings up to terminal points
Boiler filling line with all accessories
All structure supports from ground floor and tie beams required
Silencers for S/H steam, start-up vent valves (2 Nos.)
Monorails for fans, feed pumps
Monorails for ESP Top for rectifier maintenance
All drains to the ground floor and to drains to be channel up to battery limit
All field instruments including control and actuators
ESP MCC 3 ph, 4 wire, 50 kA, 415 V rectifier transformer and TR set control
panels
ESP system equipment
LPB station drives
Overground earthing for ESP equipments up to ground level
Digital energy meter for ESP MCC and hook up to DCS
Microprocessor based ESP controller
PLC based ESP rapping Mechanism
Motorised valves and actuators
All LT/HT & integral motors
-8-
3.1
All flow meters
All control dampers with smart electro pneumatic valve positioners
Bottom mounted bed temperature thermocouples
Primary elements for feed water flow, steam flow and air flow
Spares for start-up and commissioning
All staircases as per industrial standards and no monkey ladders shall be

allowed.
Surge hoppers for all the bunkers
Motor control centers
Earthing upto ground level
Primer painting
Stress analysis of steam piping upto anchor point, however, supply shall be
upto main steam stop valve/NRV
Target plates required for steam blowing.
SWAS Package
All Electrical / instrument GI cable Trays
Scope and Extent of Services

Vendor shall be fully responsible for erection of the items supplied by them and
assistance during start-up and commissioning of Equipment. The details of the
scope of work and services of the Vendor shall be as given below:
3.1.1
Submission of Activity Chart
Vendor shall submit activity chart prior to commencement of erection to depict

the activity schedule planned to complete erection, to match with commissioning
schedule of Equipment.
3.1.2
Receipt and Inspection
Vendor shall be responsible for receipt and unloading of all the erection materials
under supply from VENDOR and also arrange to store the materials in the
Purchaser's storage yard/temporary storage space of the Vendor.
Vendor shall be responsible for inspection and checking of all the erection materials
with the shipping list, consignment note and drawings of Vendor, upon receipt at
-9-
site and report to Purchaser regarding their correctness and about missing/damaged
items.
3.1.3
Liaison with Inspectorate of Steam Boilers
Vendor shall be required to carry out liaison work with Inspector of Steam
Boilers,
Submission of the relevant documents/certificates such as commencement
certificate, progress report, completion report etc., pertaining to erection of
pressure parts to Inspectorate of Steam Boilers in compliance with Indian Boiler
Regulations (IBR).
Obtaining approval from Inspectorate of Steam Boilers for Vendor and his subVendor for undertaking erection.
Arranging for site inspection of all pressure parts by Chief Inspector of Boilers,
prior to commencement of the work and to obtain clearance to carry out work.
3.1.4
Deployment of Manpower
Scope of services of the Vendor shall include provision of a team of erection

engineers, supervisors, skilled/un-skilled manpower required for erection and
commissioning.
3.1.5
Boarding and Lodging for Erection Personnel
Vendor shall be responsible for arranging boarding, lodging and conveyance for
his entire manpower.
3.1.6
Site Construction Facilities
Vendor shall make its own arrangement for construction of site office/temporary
store room in the place provided by Jubilant.
3.2
Erection (For VENDOR Supplied equipments only)
The erection services of Vendor shall include, but not limited to, the activities
highlighted below:
Vendor shall take delivery of materials from purchaser storage area/Vendor's

storage area in sequential order to match with erection sequence.
All the materials shall be cleaned/wire brushed, prior to erection.
Minor transit damages on the materials shall be repaired by the Vendor, free of
cost. For major damages, the Vendor shall carry out the repairs at supplier
cost.
However, the repairs, which have been caused due to mis-handling or

negligence on the part of Vendor, shall be carried out by Vendor, free of cost.
- 10 -
Proper records shall be maintained for various critical dimensions/clearances

etc., and the copies of such records shall be mutually signed by the Purchaser
and Vendor to ensure adherence to the Vendor's recommendations.
Erection work shall be carried out in the manner and sequence as may be
directed by Purchaser's representative/Vendor's recommendation.
Vendor shall notify Purchaser sufficiently in advance, ensuring the requirement

of materials and any other items that are to be supplied by Purchaser.
Leading of all materials from the Purchaser's storage yard/ Vendor's storage
yard to the respective foundations of the material.
Inspection of the civil foundations of boiler and other equipment, prior to

commencement of erection to check dimensions, correctness of grouting the
elevations etc. Deviations, if any, shall be brought to the notice of the
Purchaser.
Pre-assembly of various structural materials, ducting, rotating machinery, as

envisaged by Vendor.
Placement on foundation and in position and subsequent alignment, checking

and cleaning as required, as per detailed specifications, drawings,
instructions. Vendor shall provide stainless/brass shims for final alignment
and adjustment, in addition to packing plates. Number of packing plates
shall be kept minimum. Gas cutting, machining/ grinding of the packing
plates to suit the required size, as per Purchaser/Vendor shall be carried out
by the Vendor.
Fabrication and erection of temporary fixtures/piping, like scaffolding,

structural frames etc., which are not permanent, but are incidental to erection
shall be carried out by Vendor.
All integral pipe works of boiler shall be as per Vendor's certified drawings.
Minor modifications on pre-fabricated pipes shall also be considered as
activity incident to erection work..
All pressure parts shall be cleaned with compressed air and sponge test, if
necessary, shall be carried out to confirm that the tubes are free from
choking.
Supervision of erection Erection, alignment and coupling of motors of

various equipment, which are under supply by Purchaser, shall also be carried
out by Vendor.
Vendor shall make necessary action for any mistake during erection, errors
made in the drawings, fabrication and transportation.
Vendor shall also carry out improvements/modifications as suggested by

Purchaser & mutually agreed during the course of erection for betterment of
layout at no extra cost.
- 11 -
Welding of pressure parts, high pressure piping and all internal high pressure
piping and all internal piping covered under IBR shall be done by certified
welders, duly qualified as per the provisions of IBR. However, these welders
shall be tested at site by Purchaser to ascertain their suitability.
Welding of pressure parts, tube/pipes, of sizes 63.5 mm dia. and below shall
be carried out by tungsten inert gas (TIG) welding and size greater than 63.5
mm dia. shall have root welding by TIG and filling by sub-merged metal arc
welding (SMAW).
Radiography of pressure parts and piping shall be carried out as stipulated in

IBR (1950) with latest amendments.
All alloy steel welding joints on pipes shall be heat-treated/stress relieved, as

stipulated by IBR and also as recommended by Vendor.
All structural and duct welding shall be carried out, utilising electrodes
conforming to AWS E 6013.
Scope of work shall also include erection of such instruments that are
necessarily to be fixed/attached to the pressure parts/non-pressure parts. The
necessary power cylinders, hydraulic piping etc., shall also be included in the
scope of erection.
Vendor is fully responsible for lining and insulation work of boiler, piping,
covered in the scope. The details of scope of services shall be:
Application of various types of refractory, including castables, standard

and shaped firebricks, refractory mortar, cement plaster etc., and
insulation materials, external sheet casings for Equipment covered under
this Contract
Chipping and cutting of firebricks to suit the site conditions
Application of insulation covering both application of ready made wool

mattresses and preparation and application of specified thickness and
shaped mattress like single layer or multi-layer out of loose wool with
one side or all sides wire mesh.
Vendor shall be responsible for provision of all consumables, welding

electrodes, oxygen/acetylene gas etc.
Vendor shall be responsible for provision of tools, tackles, handling devices

etc., to carry out the erection. Vendor shall provide all precision equipments
like micro level, dial and other gauges, surface plates, straight edges,
radiography equipment, stress relieving equipment etc., for the erection.
Vendor shall submit every fortnight the progress report to Purchaser for his
review. In case Purchaser feels at any stage that the progress of work needs
expediting, so as to ensure completion of work within the stipulated time,
- 12 -
Purchaser shall have the right to instruct the Vendor to increase Vendor's
manpower.
Vendor shall keep a competent representative, who will be responsible and

shall remain Site In-charge to execute all activities connected with erection.
Vendor shall submit the proposed organisation chart for undertaking erection
and commissioning.
Vendor shall place sufficient number of

engineers/supervisors in addition to Site In-charge.
Site In-charge shall not abstain himself from site without obtaining permission
from Purchaser.
Vendor shall work under the guidance and directions from Purchaser/
Consultants.
All statutory rules under Labour Laws prevailing in Maharashtra shall be

observed by the Vendor.
Vendor shall ensure that his team shall adapt all safety measures to avoid
occurrence of accidents.
Vendor shall work in close co-ordination with building Vendor or other

agencies, who will also be working in the same area simultaneously to speed
up the overall commissioning.
Vendor is responsible for making the regular payments to their labour / sub
Vendor.
In case of any accident during the course of the erection, testing,

commissioning (VENDOR items supplied), all the responsibility shall be with
the Vendor only.
- 13 -
competent
erection
3.3
Painting
3.3.3
Finishing Paint - Only Primer painting
3.3.4
Pre-commissioning Testing
After completion of erection, the pressure part system of the boiler and piping
shall be hydraulically tested to the required pressure. Vendor shall provide the
necessary blanking arrangement for such hydraulic tests.
Vendor shall be responsible for offering boiler pressure parts and piping for
statutory hydraulic test in the presence of Inspector of Boilers.
The furnace and ducting shall be subjected to leak test and all leaks shall be
attended to, prior to application of insulation.
3.3.5
Trials and Commissioning
Vendor shall assist Jubilant during pre-commissioning checks, trial runs of the
equipment and commissioning.
Vendor shall also provide, at appropriate time, personnel for pre-commissioning
checks, trials and commissioning.
Vendor shall provide, well in advance, to Purchaser various checklists,
commissioning procedures and other details for perusal of the Purchaser.
3.3.6
Purchaser's Responsibility
Purchaser shall arrange the following items/facilities:
All civil work like Equipment foundations, brickwork, flooring, structure,

platforms, ladder, ducting & bunker etc. & erection of the same which ever is
in Jubilant scope
Necessary water, compressed air, and power at one point at/near the erection
site
Necessary office at Site, as available
Adequate lighting system at erection site to enable erection and

commissioning work to progress throughout twenty four hours in a day
All statutory fees towards IBR shall be borne by Jubilant. However, Vendor shall
co-ordinate with Boiler Inspectorate for smooth execution of the works.
Purchaser shall give to Vendor, in due time, any information concerning local laws
and regulations which is necessary for proper execution of Contract.
Purchaser shall designate in writing a competent representative to be his channel
of communication with Vendor's staff.
- 14 -
4.0
BASIS FOR DESIGN
4.1
General
Boilers and their auxiliaries are designed and manufactured in full accordance
with the relevant codes and regulations and shall be capable of safe and
continuous operation under all conditions without strain, vibration or other
operational difficulties.
Boilers, their components and associated plant are properly designed and
constructed and shall be provided with suitable supports to permit free expansion
and contraction without causing leakage or distortion of any item of the
equipment.
The analysis of the fuels shall be fully taken into account in the design, and the
furnace volume, heat release rates and refractory areas are to be selected suitably.
Other features of the design shall be based accordingly and the erosive effects on
the pressure parts and other parts of the boiler shall be minimised by the
avoidance of excessive gas velocities and undue carry over.
All parts and components, subject to corrosion, erosion or other deterioration
shall be made of materials suitable for the application and an adequate allowance
shall be provided in the design for this deterioration.
The design of the boilers and their auxiliaries is such that maintenance
requirements are facilitated and that easy access is available to parts and
components requiring replacement from time to time.
All equipment shall be suitable for operation under hot and humid tropical
conditions..
Noise level shall be less than 80 dB.
4.2
Site Data
AMBIENT CONDITIONS:
Plant Elevation above Mean Sea Level (MSL)
Temperatures :
*
*
Maximum Air Temperature

Ambient Temperature
:
:
43 deg C
35 deg C
*
*
Minimum Temperature
Plant Design Temperature
(Performance design)
:
:
19 Deg C
---
Plant Design Wet Bulb Temperature
25 Deg C
- 15 -
Plant Design Temperature for Electrical

Equipment
---
Relative Humidity :
*
Maximum
99.4
Minimum
16.4
Plant Design Relative

Humidity
----
Wind :
Wind Direction
: West to East for 8 moths &

East to west for remaining 4
months
Design Wind Velocity
Seismic Zone
: 15 Kmph
: III, as per IS 1893 Rev 3:
1975
Climatic Condition
4.3.3
Hot and Dusty
Compressed Air
Operation pressure
4.3.4
kg/cm2 (g)4.5
Electrical
Power supply for motors:

Upto and including 160 kW rating
>160 kW<1000 kW
Below 0.25 kW :
Non-critical
Critical
415 V, 50 Hz, 3 phase

11 kV, 50 Hz, 3 phase
240 V, 50Hz, single phase
415V, 50 Hz, 3 phase
Control voltage for motor control

centres and circuit breakers
240, 50 Hz, AC
Trip supply for breakers

Control voltage for instruments
Voltage for power sockets and illumination
Voltage power supply to converters
- 16 -
110 V DC
240 V, 50 Hz, AC
240 V, 50 Hz, AC
415 V, 50 Hz, 3 phase
Voltage for integral motors supplied

along with the equipment
4.4
415 V, 50 Hz, 3 phase
Instrumentation
Type of Instruments
Control valves (Pneumatic/Electrical

motorised) ,rpcs,sopcs,analyser , temp
Sensors, smart field instt, VFD etc
Electronic Field Instruments,
Smart type (HART Protocol), 2 wire
system wherever possible
Level of instrumentation
4.5
To suit plant operation from

DCS
Piping
All steam piping and valves shall be as per ANSI Standard.

5.0
APPLICABLE ACTS AND REGULATIONS

The design, materials and construction of the boilers should be in accordance
with Indian Boiler Regulations (IBR) 1950, (with the latest amendments),
International Standard Organisation Code (ISO) and Vendor shall be responsible
for obtaining the approval for the boiler under IBR.
In this connection, Vendor shall take appropriate steps from the design stage by
providing the necessary drawings, certificates, design calculations, material
fabrication details and all other information required by Indian Boiler
Regulations, duly approved by the Inspectorate of Steam Boiler, Punjab, India.
Copies of all such submissions shall also be sent in triplicate to Purchaser. The
provisions of IBR shall be considered as the minimum requirements and Vendor
shall include any additional measures considered necessary for safe operation of
the boilers.
Radiograph inspection and heat treatment of pressure parts in the manufacturer's
works shall be in accordance with IBR.
Similarly, all relevant provisions of Indian Factories Act, Indian Explosives Act
and all other applicable requirements shall be observed in the design and
manufacture.
All costs incurred in complying with these acts, rules and regulations shall be
borne by the Vendor.
6.0
DETAILED SPECIFICATION
6.1
Boiler Pressure Parts
- 17 -
6.1.1
Steam Drum
Steam drum shall be of all welded construction, completely radiographed to prove

weld soundness, stress relieved and hydraulically tested. The drum shall be
fabricated from boiler quality plate to the appropriate specification and
constructed in accordance with IBR.
Steam drum shall be provided with suitable dished-ends and manholes, with a
swing type opening internally and internal extension pipes shall be fitted in the
drums as appropriate to ensure uniform distribution or collection for the duty
involved.
Steam drum shall have manifold connections to the superheater headers. Nozzles
shall be provided for the external mounting of safety valves, water level gauges,
water level alarms, water level regulators, pressure gauges, continuous blow
down, feed water inlet, chemical injection, sampling, air vent and any other uses
of steam from the drum.
The steam drum shall be provided with effective means for ensuring separation of
water particles from the steam comprising a girth baffle, and a two stage system
of vortex separators and chevron scrubbers or the like to produce steam with a
purity better than the following:Silica
Iron
Copper
6.1.2
less than 0.02 ppm

less than 0.02 ppm
less than 0.003 ppm
Furnace Tubes and Headers
Furnace tubes shall be of seamless carbon steel conforming to ASME Standard or

equivalent. Tubes connecting to the steam drum shall enter radically. Tube ends
terminating at headers shall be welded to stub tubes provided on the headers.
The furnace shall be of fully water cooled construction comprising membrane
walls with integral fins and welded gas tight. Refractory linings, ignition and
burn-out arches shall be employed, as required by the design, and shall be fully
detailed.
The headers shall be designed and manufactured in accordance with IBR and shall
be of adequate size and of seamless carbon steel conforming to ASME Standards
or equivalent with welded end caps. The necessary drain connections, peep-holes
and hand-holes shall be provided as required.
Connections to the steam drum and connections to the headers shall be designed
so as to form an integral circuit providing adequate natural circulation under all
operating conditions.
All fittings and supports, supply and riser connections and the necessary access,
inspection and burner ports shall be provided.
- 18 -
6.1.3
Superheaters and Desuperheater
The superheaters shall comprise primary and secondary sections located

appropriately in the radiant and convection zones and shall be complete with all
manifolds, fittings, supports, supply and drain connections and inter-connecting
piping.
The superheater tubes shall be seamless with the tube materials conforming to
ASME Standard or equivalent, selected to suit the superheater metal
temperatures and the method of suspension shall be designed to permit free
expansion.
Where the superheater metal temperatures shall be high enough for creep to be a
consideration, the tube dimensions and materials of construction shall be selected
to give a design creep life in excess of 100,000 hours.
De-superheater, of spray type, shall be provided in the steam flow between the
primary and secondary superheaters and shall be controlled from the superheater
outlet temperature. The secondary superheater outlet temperatures shall,
preferably, be the highest steam temperatures in the system.
Spray water shall be derived from the feed pump discharge only. The pumps shall
be of multi-stage centrifugal type with hydraulic balancing of the stages and shall
be complete with gland sealing, lubrication and bearing cooling arrangements.
6.1.4
Economiser
The economiser shall be of bare tube construction with seamless carbon steel
tubes conforming to ASME Standard or equivalent and of continuous loop type
with inlet and outlet headers. The economiser units shall be supported in a
structural steel frame and enclosed within a 5 mm thick welded steel casing.
Doors shall be provided for observation and also to obtain access for
maintenance.
The economiser shall be complete with necessary drains, vents, thermometer
pockets and pressure gauge connections.
6.1.5
Boiler Mountings and Fittings
The boiler shall be provided with a complete set of mountings and fittings, of
reputed make, in accordance with Indian Boiler Regulations for the safe operation
of the boiler and the following shall be included, without limitation. Root valves
shall be provided for all HP valves.
For Steam drum
Safety valves
Continuous blow down valves
Direct water level gauge with isolating valves
Hydrastep (Yarway control)
- 19 -
Air vent valves

Pressure gauge with isolation valves (2 Nos with 10 Dial Size)
Chemical dosing valve and check valve
Valves for auxiliary supplies
Sampling valves
Valves for all impulse piping
Sample piping
For Feed Water Line
Regulator valve
Isolation valves for regulator
Regulator by-pass valve
Feed water regulator drain valve
Non return valve
Pressure gauge isolation valves
Thermometers with thermowells
For Headers
Air vent valves

Drain valves
Blow down valves
For Economiser
Isolation valve
Air vent valve
Thermometer
Drain valve
Pressure gauge with isolation valve
For Superheater Header
Safety valve of reputed make along with silencer

Motor operated main steam stop valve with bypass
Main steam non-return valve
Motor operated start-up vent valve with isolation valve and silencer
Air vent valves
Pressure gauge with isolation valves
Thermometers
Sampling valves
Note: All isolation of high steam and water lines will have two valves in series.
6.2
Fuel Firing and Ash Removal System
In view of the different fuels to be fired in the boiler, Vendor is required to apply
his knowledge and proven experience to provide necessary fuel firing/ash removal
- 20 -
system/ equipment, which he considers suitable in all respects for the present
application.
This section of the specifications, therefore, outlines certain principles that may
be followed by Vendor but Vendor may adopt or modify them in whole or in part
in the proposals he puts forward with specified guarantees.
Vendor shall describe and justify his proposed design and submit the necessary
additional schedules to define the main parameters and materials of construction
of the equipment included.
6.2.1
Solid Fuel Firing System
6.2.1.1 Fuel Bunker and Chute
Indigenous coal, Imported Coal.
6.2.1.2
Boiler shall be provided with a separate welded mild steel overhead live
storage bunker for indigenous coal, imported coal with effective storage
capacity for 24hrs operation,. Water volume of bunker of boiler will be
accordingly.
Solid Fuel Firing System
Boilers shall adopt fluidised bed combustion system of proven type with underbed
fuel feeding system, selected based on the fines content of fuel specified.
Evaporator coils may be immersed in the fluidised bed as applicable and coils shall
be properly studded and spaced out to avoid erosion. Both fuel and air nozzles
shall be of stainless steel. Vendor shall fully describe the feeding system selected,
highlighting the salient features. Vendor shall consider underbed feeding system
for imported coal
Fuel feeding system shall be arranged with suitable variable frequency drives
(VFD) for underfeeding systems.
6.3
Boiler Ash and Dust Discharge System
The boiler shall be provided with ash drainpipes suitable for discharging the ash.
If required by the design, hopper shall be provided to collect the dust from
different outlets, either for re-firing or for disposal, as applicable. The hoppers
shall be constructed of mild steel plate of adequate thickness with suitable
reinforcement and support. Air lock, rotary valves shall be provided at the
outlets of chutes and hopper, as applicable. Necessary ash coolers (water
Cooled) shall be provided to cool the ash to around 150C for further disposal.
The ash analysis shall be given for the convenience of ash handling system.
Vendor shall describe the ash/dust removal system proposed and indicate clearly
the terminal points considered for supply.
- 21 -
6.4
Electrostatic Precipitator
Vendor shall include one (1) electrostatic precipitator for boiler to meet the
allowable dust emission as stipulated by the latest Pollution Control Standards (as
applicable to the State , India) limiting the dust concentration not exceeding 50
mg/Nm3 (dry) with all field in service & VENDOR will indicate the emission level
during any one field out of service. Scope of supply shall also include rectifier,
transformers hopper low & high level monitoring and controls etc along with
supporting structure, hoppers, heaters, MCC etc.
Vendor shall fully describe the sizing philosophy adopted and shall furnish the
details on emitting and collecting system with material of construction.
The elevation of hopper outlet flange shall be at +3.5 m from finished floor level.
The jubilant scope of work for ESP shall be Civil work based on Load data,
6.5
Air and Flue Gas Systems
6.5.1
Combustion Air Distribution System
Combustion air distribution system shall be specifically designed for the proposed
fluidised bed firing. The design of the proposed distribution and the means for
controlling the air admission shall be fully described.
6.5.2
Fans and Draught System
Boiler shall adopt balanced-draught system with 2x60% induced draught (ID)
fans and 2x60% forced draught (FD) fans and 2x125% primary air fans/secondary
air fans. Both ID and FD fans shall be provided with damper. Vendor should state,
in the Schedules, the design basis for the fans and the margins incorporated in the
fans for the design head and capacity. The fans shall be designed with the latest
technology to achieve maximum efficiency and shall be provided with necessary
control dampers with actuators. fan and motor may be mounted on a common
base frame and provided with flexible coupling and guard. Motor shall be
procured and supplied by VENDOR. However, coupling halves for motor and
fan with bolts and nuts and foundation bolts shall be included in Vendor's scope of
supply. Coupling halves shall be properly balanced.
Suction for the FD fan shall be taken at sufficiently high level to avoid
entrainment of floor surface dust and Vendor shall select suitable location.
Locating venturi type metering in the suction duct is preferred for air flow
measurement.
The ID fan shall be designed and constructed to resist erosion. Vendor should
state the features incorporated in this respect. Isolating damper shall be provided
at the fan discharge to the chimney.
- 22 -
All fans except ID fan shall be designed to run at 1440 /1500 rpm or less and the
ID fan shall be designed to run at 1000 rpm. Vendor shall provide characteristic
curves for the pump, fans and other equipment.
Purchaser may also decide to install variable frequency drives for all the
fans/pumps at later date wherever appropriate. Hence, fans/pumps etc. shall be
selected suitably.
6.5.3
Air Heater
If required by the design, boiler shall be provided with a tubular air heater along
with economiser to recover heat from flue gas and pre-heat the combustion air,
limiting the flue gas temperature not exceeding 150C, when leaving air heater.
The air heater shall comprise ERW annealed tubes conforming to BS-1775 or
equivalent, suitable for expansion and complete with tube plates, supports, casing,
dampers .
Vendor shall clearly state the proposed operation of the air heater on the different
fuels and the appropriate flue gas outlet temperatures shall be stated.
6.5.4
Duct Work and Dampers
Boiler shall be complete with necessary cold air, hot air and flue gas ducting
required for all purposes.The ducting shall be constructed of mild steel sheet,
as necessary, with angle iron end frames, and the joints made gas/air-tight by
means of suitable gaskets. The air and flue gas ductings shall be adequately
stiffened and supported to withstand the pressures involved and to prevent
vibration. Necessary intake silencers, grills, access doors, expansion bellows
and isolating devices shall be provided. External cleats shall be fitted to hot
ducting to facilitate the application of lagging. All ducting should be above
the finished floor level.
Flue gas velocity in the ducts shall not exceed 12 m/s.

Necessary heavy duty dampers and bypass dampers shall be provided complete
with actuators, visual position indicators and means of securing as required by the
design.
6.5.5 Chimney (RCC)
The Purchaser shall construct the RCC Chimney. However the Vendor shall
provide the Diameter, Height and GA Drawings of the same
6.6
Feed Water System
Feed water system of the boiler shall comprise 2 x 120% MCR feed pumps, HP
chemical dosing system and connected control stations and piping. The details of
the system are further described below.
- 23 -
6.6.1
Deaerator and Feed tank
6.6.1.1 Deaerator
A deaerator-cum-feed water tank shall be included in the scope of supply with

DM water temperature around 27C, outlet as per design and to limit O 2 content
in the feed water outlet not exceeding 0.007 ppm. Deaerator shall be supplied
with heat recovery system, level control system, overflow system, temperature
control system, safety valves and other fittings. Deaerator shall have the stubs
necessary for the following.
6.22 DEAERATOR, FEED STORAGE TANK; PIPING, VALVES AND FITTINGS

The Deaerator, Feed Storage Tank, the Feed pumps with the drive system shall be
supplied by Vendor , and will be briefly as below:
1.
DEAERATOR
Type
Arrangement
- Spray cum Tray

- Cylindrical, Vertical Flange
Mounted over Feed Storage
Tank-Vendor to be specify
Size
-Max. Capacity (110% Boiler MCR)-Operating pressure and temp.
TPH
0.232 Kg/cm 2g (105C)
-Design pressure
2.5 Kg/cm 2g
ASME Sec VIII Div.1
Design Code
Boiler 100% MCR 110% MCR

At minimum temperature of 27C,
(100% DM Water)
DM water
Flow
TPH
Auxiliary steam Flow

Deaerated water
flow to boiler (including
BD): at 105C
TPH
Total
TPH
The Deaerator will be complete with all the connected

piping (Auxiliary steam & DM Water) Valves and Fittings,
all as shown in the P&ID. The DM Water & auxillary
Steam piping shall be done by Jubilant upto Control valve
inlet. 2 spare water inlet nozzle to be provided at deaerator for 100 % flow.
- 24 -
The Spray nozzles and Trays of deaerator will be of Stainless steel.
The Deaerator has been designed and sized considered the following
worst case (as desired).
a) DM water at 27C (min. temperature level), at 2.5-3 kg/cm 2g (min.
pressure) at the inlet of Level Control valve unit, near the Deaerator
unit.
b) Auxiliary steam at 4.0-5.0 Kg/cm 2g to be supplied from control valve
inlet, for deaeration and Feed heating at the Deaerator Pressure
Control valve unit inlet (max. 13 TPH at 110% MCR).
2. FEED STORAGE TANK
-Type / Arrangement; Location
-Supports arrangement
Horizontal, Cylindrical
-
2 No. Saddle supports;
FW Tank unit placed on

the roof of the independent
support based on the NPSH
requirement.
-Size approx.: ODxShell
- Capacity of water holding (as

Specified) (between NWL and Trip)
vendor to be specify
- 20 Min.Storage at 110% MCR
Operating pressure and temp.
0.5 Kg/cm 2g; 105C
Design pressure
2.5 Kg/cm 2g
-Design code
ASME Sec VIII Div.1
The Feed Water Storage Tank will be complete, with all the
connected piping, valves and fittings
The Feed tank has been sized for 110% Boiler MCR conditions, and
with 20 min. water holding capacity between NWL and Trip level
with 60% tank height.
3.
ARRANGEMENT / LOCATION OF FW STORAGE TANK AND FEED PUMPS
1) The Feed water storage tank (with the Deaerator mounted and supported
on this tank) will be placed over independent structure, at required NPSH
level.
2) The 2 x 120% Feed pump will be located at Ground level
- 25 -
6.6.2
Feed Pumps
2 x 120% MCR electrically driven feed pumps (one running and one stand-by for
boiler) shall be supplied for the power boiler. Pumps shall be of multistage
centrifugal type, complete with balance chamber and necessary suction and
delivery valves, non-return valves and leak-off valves to cater to start-up and low
flow conditions, gland sealing and bearing cooling pipe work, valves and flow
indicators. The feed pumps leak-off lines shall discharge to the deaerator via
isolating and non-return valves. The pumps shall be supplied with necessary
suction and discharge lines. Auto Recirculation Valve (ARC) of imported make
shall be provided. All the piping like leak valves, minimum discharge lines along
with isolation, NRV etc. from feed pump up to deaerator shall be included in the
scope of supply of Vendor.
The pump and motor shall be mounted on a common base frame and provided
with a flexible guard. However, coupling halves bolts/nuts and foundations bolts
for motor and pump shall be included in Vendor's scope of supply. Coupling
halves shall be properly balanced. One (1) tapping with an isolation valve shall be
provided on the discharge header of boiler feed water pumps to supply feed water
to 105 ata for Desuperheating Station. The size of the tapping shall be suitable for
a flow of 15 tph at boiler feed pump discharge pressure.
6.6.3
Feed Water Control System
The control station shall be provided for drum level control with smart electropneumatic control valve, isolating valve, bypass valve, drain valve etc.
6.6.4
Chemical Dosing
Vendor shall include suitable HP and LP chemical dosing systems and the same
shall be supplied with mixing tank, pumps, piping, valves and fittings. HP and LP
chemical dosing tanks and piping shall be of stainless steel. HP dosing system
shall have two (2) pumps for boiler (one running and one stand-by) and LP dosing
system shall have two (2) pumps (one (1) running and one (1) stand-by) common
for the boiler. DM water piping from one point in the Boiler area.
6.6.6
Sampling Lines and Coolers
Sampling lines shall be provided for feed water, drum water, saturated steam and
superheated steam. Sampling lines and nozzles shall be of stainless steel.
6.7
Boiler Structure and Other Accessories
6.7.1
Boiler Structure
Boiler shall be provided with necessary supporting structures from ground level.
The structures shall be fabricated from rolled steel sections to support the boiler,
air distribution system and other auxiliaries. The structures shall incorporate
necessary columns, beams, overhead steelworks and supports,
- 26 -
Boiler shall be provided with necessary platforms, ladders, stairways and support
steelworks to facilitate safe access to all parts of the boiler for operational and
maintenance purposes.
The structure shall incorporate necessary lifting beams and hoist blocks wherever
required for maintenance purposes. All the design and details shall be as per
relevant IS Code.
6.7.2
Refractory and Insulation
Refractory and insulation of the boiler and its auxiliaries shall be complete with
necessary castable refractory, refractory bricks and blocks as required by the
design, together with requisite fixings, holders and other attachments. The
refractory and insulation materials shall comply with relevant Indian Standards.
Boiler furnace area shall be neatly covered with mineral wool mattress of
acceptable quality and required thickness and cladded with corrugated aluminium
sheeting of thickness not less than 22 SWG (VENDOR shall consider corrugated
aluminium cladding sheet of 22 SWG thk for water wall and plain aluminium
cladding sheet of 22 SWG thk for other zone). The maximum skin temperature
of the casing shall not exceed 10C above ambient when the boiler is operating at
MCR. The exposed portions of the boiler drums, integral pipe work, casing of
economiser, air heater, steam and feed water lines shall be provided with
necessary insulation and clad with aluminium sheeting neatly attached, so as to
limit the skin temperature to 10C above ambient. Removable insulated boxes
shall be provided for valves and provision shall also be made for easy removal of
the insulation at flanges without affecting the general pipe work insulation.
All drain lines, vent and exhaust lines and all other components at high
temperature shall be covered with a sufficient thickness of insulation for personal
safety.
Necessary seals, expansion joints, door linings, fire clay and fire cement and all
other items to complete the installation shall also be included.
Vendor should describe the proposed arrangement of refractory and insulation of
various sections.
6.7.3
Soot Blowers
Soot blowers, if required shall be supplied by the Vendor.

6.7.4
Blow Down Tanks
One (1) IBD tank and one (1) CBD tank for the boiler. Separate IBD & CBD
blow down tanks of adequate capacity & both the tanks should be connected with
level control shall be provided to receive all intermittent and continuous blow
down and all other drain discharges from the boilers. Tanks shall be supplied with
supports and vent of adequate size. Vent pipe shall be extended at least 10 m
- 27 -
from the top of the tank. Vendor shall also make provision for utilising flash
steam of blow down tank in deaerator or elsewhere.
6.7.5
Foundation Bolts
All foundation bolts, fixings and attachments shall be included in Vendor's scope
of supply for the items supplied by VENDOR.
6.7.6
Consumable Materials
Vendor shall provide a specification for all consumable materials required for
satisfactory operation of the plant.
6.7.7
Special Tools
A pneumatic operated expander with sufficient set of mandrill shall be provided to

cover the full range of tubes together with a set of other special tools and tackles
required for the erection and maintenance of the boiler.
6.7.8
Start-up and Commissioning Spares
Vendor shall provide free of cost to Purchaser all Spare Parts that may require
replacement at the time of Start-up and Commissioning of Equipment.
6.8
Piping, Valves and Fittings
All the integral pipe work associated with the boiler shall be provided including
the necessary valves including motorised main stop valve, along with motor and
integrated bypass valve motorised start-up vent valve, fittings, flanges, gaskets,
nuts, bolts, clips, hangers and all other items required to complete the installation.
Adequate means for accommodating expansion shall be incorporated as
appropriate. All HP valves shall be provided with a root valves.
The pipe work shall include:
Suction pipe work of feed pump from outlet flange of deaerator- cumstorage tank outlet to suction of pumps.
Discharge pipe work of feed pumps discharge nozzles to feed water control
system
Piping connecting feed water control station and economiser.
Piping between economiser outlet and steam drum.
Desuperheater and economiser recirculation pipe work, as required by the
design.
Superheated steam piping including main steam stop valve & non-return
- 28 -
valve.
Superheater safety valve discharge pipe work to atmosphere, including
exhaust silencer.
Drum safety valve discharge pipe work to atmosphere, including exhaust
silencer.
Start-up air vent, discharge pipe to atmosphere including silencer.
All air vent piping.
Feed water and boiler drum water sampling pipe work.
Superheated steam and saturated steam sampling pipe work.
HP chemical dosing pipe work.
LP chemical dosing pipe work.
All blow down pipe work.
All drains from steam lines, headers and all other drain lines and collecting
manifolds to blow down collecting tank.
All cooling water and service water pipe work from common supply point
and to drain.
All instrument air pipe work from common supply point.
HT/LT Electric Motors
Vendor shall provide all integral electric motors, like motorised valves, etc.
forming part of the equipment. Vendor shall also include necessary couplings,
base frame, foundation bolts for the equipment and motors
6.9
Instrumentation and Controls
6.9.1
General
Boiler shall be provided with proven control system together with necessary
instruments as required by appropriate regulations and also for fail safe and
efficient operation. Equipment incorporated shall be of electronic type excepting
control valves and damper actuators, which shall be of pneumatic type.
Purchaser has plans to operate the boilers with DCS incorporating all the controls
and execution of safety and sequence logics as recommended by the boiler
Vendor. DCS shall be provided by Jubilant.
- 29 -
6.9.2
Type of Instrumentation
All the instruments shall be of proven design and shall be of a high degree of
reliability.
Instruments shall be of state-of-art-technology and be of the latest design.
They shall be of SMART version with Hart protocol.
Revamped/retrofitted components are not acceptable.
The instruments selected shall be the best suited to the process application for
which they are used.
Control valves shall be properly sized to handle the flow and the metallurgy shall
be suitable for the process conditions in which they are installed. They shall have
pneumatic valve positioners.
All control valves shall have position indicators for feed back in system.
All on-off valves shall have end position proximity switches to monitor the
open/close position.
Vendors responsibility includes terminating all the field devices in their respective
Junction Boxes.
Adequate sampling points, as necessary, shall be indicated for any analytical
instruments used.
All field instruments, control and on-off valves, analytical instruments shall be in
the scope of Vendor.
All controls shall be from DCS.
All thermowell design temperature shall be 1.5 times more than operating
temperature.
It is Vendors responsibility to provide control and safety logics for
implementation in DCS. This shall be verified and certified by Vendor during
Factory Acceptance Test at DCS Vendors works.
For any speciality instrument, specific to Vendors Equipment, which is not part of
Vendors list, Purchasers prior approval is to be obtained before ordering.
Vendor shall include consumables and commissioning spares as part of the supply.
Erection of VENDOR supplied equipments, erection supervision, start-up and
training shall be in VENDOR scope
All field instruments shall be in Vendors scope. Vendor shall attach a list of
instruments under his scope including make, type, etc.
- 30 -
Field analog signals shall be 4-20 mA isolated.

Analog outputs from system shall be 4-20 mA.
Field digital input shall be integrated by 24 V DC from system. MCC digital input
to system shall be 220 V AC.
All field transmitters will be of 2 wire type; wherever necessary, 4 wire
transmitters shall be powered by 220 V AC from UPS.
Vendor shall give approximate I/O count for the instrumentation. Actual count
can be decided during detailed engineering.
All instruments shall be offered from the approved Vendor list by Purchaser.
Deviation, if any, shall be only with prior approval of Purchaser.
Local gauges are to be provided as necessary.
Inputs to DCS shall be so selected by Vendor to offer suitability of trending and
computation of alarm in DCS.
Furnace pressure measurement shall have redundancy pressure transmitter.
ESP control system shall have RS 485 connectivity to interface with main DCS
for monitoring purpose.
The philosophy of operation and control of power boilers shall be based on coordination of all plant items from a Central Control Room.
Electronic transmitters of smart type shall be provided including temperature
measurement. All RTD and thermocouple temperature elements shall be provided
with a 2 wire, 4 - 20 mA DC transmitter.
Flow instrumentation shall incorporate temperature and pressure compensation as
applicable.
All I/P converters shall be of field mounted type.
Two (2) wire signal transmission with a signalling range of 4 to 20 mA DC is to
be adopted between field and control room instrumentation. Control and
monitoring shall be capable of accepting transmitter outputs without requiring
external signal conditioning.
6.9.3
Details of Controls for boiler operation
These shall comprise the following but not limited to:

a) Three element drum level control system with two out of three logic signal
processing along with high and low alarms for drum level.
- 31 -
b)
Two element temperature control for steam temperature control with

attemperator control valve and final superheater system.
c)
Furnace pressure control regulation of ID fan damper.
d)
Combustion control system to control fuel feed flow by means of fuel

feeders speed control, so as to maintain a constant pressure at the outlet of
NRV of main steam line. Flue gas excess oxygen trimming shall be
included in the combustion control loop.
Proposed control systems and the schemes of instrumentation with all logic
controls for safe operation of the boilers and their auxiliaries shall be fully
described by Vendor.
Type of Instruments / primary sensors
Primary sensors for steam flow shall be flow nozzle and for feedwater flow shall
be orifice plate with carrier rings.
All control valves shall be provided with valve positioners and shall be designed
for supply air pressure of 4.50 kg/cm2 (g).
All control valves shall be provided with reputed make I/P converters for
converting 4-20 mA control signal to necessary pneumatic signal range as per
boiler Vendors control logic scheme.
All ON/OFF valves / control valves, required for the boiler protection logic
scheme shall be provided with limit switches for closed position.
For pneumatic ON/OFF valves, solenoid valves shall be provided by Vendor and
the coil shall be rated for 24 V DC.
All motorised ON/OFF dampers/valves shall be provided with all safety switches
for stopping the motor at the end positions as well as torque switches for
protecting the motor in case of jamming of the damper/valves.
Impulse piping and all the tapping points with protective wells required for fixing
the instruments shall be included in Vendor's scope of supply.
6.9.4
Parameters to be Monitored in General
The instrumentation supplied shall generally cover the monitoring of the

following parameters, but not limited to:
a)
Superheated steam
1)
2)
3)
1)
2)
b) Steam drum
- 32 -
Temperature
Pressure
Flow
Level
Pressure
c)
Attemperator
1) Steam temperature before

de-superheater
2) Steam temperature after
de-superheater
d) Drum level local indication
1) Yarway or equivalent drum

level indicator shall be
provided near the fireman
floor/Control room.
2) This instrument shall include
potential free contacts for
low/high alarms and very
low/very high drum level
tripping logic.
e)
Feed water
1) Feed pump suction pressure

2) Feed pump discharge pressure
3) Feed water pressure at
economiser inlet
4) Feed water flow
5) Feed water temperature before
economiser
6) Feed water temperature after
economiser
f)
Fuel
Coal/ feeder speed
g) Furnace
1)
2)
3)
4)
Bed height
Bed temperature
Furnace pressure
Furnace temperature
h) Combustion air
1)
2)
3)
4)
5)
i)
1) S/H inlet temperature

2) S/H outlet temperature
Pressure at FD/PA outlet

Pressure at air heater inlet
Pressure at air heater outlet
Temperature at air heater inlet
Temperature at air heater
outlet
6) Flow
Flue gas
3)
4)
5)
6)
- 33 -
Temperature after economiser

Pressure after economiser
Temperature after air heater
Pressure after air heater
7)
8)
9)
10)
7.0
Sl No
7.1
7.2
7.3
7.4
7.5
7.5.1
Temperature after ESP

Pressure after ESP
Oxygen % (O2 Analyser)
Pressure after ID fan
TECHNICAL SCHEDULE
Description
Summary of Heating Surface
Combustion chamber
Bed evaporator
Superheater
Bed superheater
Boiler bank
Economiser
Sub-total
Air heater
Total
Combustion Chamber Details
Water wall construction:
- Width
- Depth
- Mean height
Volume
Furnace volumetric heat release rate
Gas Velocity Data
Bed
Superheater
Bank tube
Economiser
Air heater
Ducts
After ESP
Steam Drum
Design code
Construction
Material Specification
Inside diameter
Thickness
Overall length
Details of steam drying equipment
Tubes, headers and Downcomers
Design code
Bed Coils
Material specification
Tube OD
- 34 -
Unit
* Vendor to be Provide
m
m
m
m
m
m
m
m
m
m
m
m
m
kcal/m3/h
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
m/s
m/s
m/s
m/s
m/s
m/s
m/s
*
*
*
*
*
*
*
mm
mm
mm
mm
*
*
*
*
*
*
*
*
*
*
*
Sl No
7.5.2
7.5.3
7.5.4
7.5.5
7.6
7.6.1
7.6.2
7.6.3
Description
Tube thickness
Tube spacing
Special provisions, if any
Furnace Tubes
Tube OD
Thickness
Tube spacing
Heating surface
Water Wall Headers
Location
Outside diameter
Thickness
Downcomer
Quantity
Outside diameter
Thickness
Circulation Ratio
Superheater
Primary Superheater
Design code
Type
Material specification :
- Tubes
- Headers
Tube OD
Tube thickness
Heating surface
Secondary Superheater
Design code
Type
- Tubes
- Headers
- Inlet
- Outlet
Tube OD
Tube thickness
Heating Surface
Bed Super Heater
Type
- Tubes
- Headers
- Inlet
- Outlet
Unit
mm
mm
mm
mm
mm
m
mm
mm
No.
mm
mm
mm
mm
m
mm
mm
m
- 35 -
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Sl No
7.7
7.8
7.9
Description
Tube OD
Tube thickness
Header Dia
Heating Surface
Desuperheater
Type
Location
Economiser
Design code
Type
- Tubes
- Headers
No. of tubes/assembly
No. of assemblies
Tube OD
Tube thickness
Heating surface
Air Heater
Design code
Type
Tube configuration
No. of tubes
Tube OD
Tube thickness
Heating surface
Means proposed to prevent
corrosion
7.9.1
Temperature at MCR
7.9.1.1
Water
Unit
mm
mm
mm
m
No.
No.
mm
mm
m2
No.
mm
mm
m
acid
Water leaving deaerator

Water entering economiser
Water leaving economiser
7.9.1.2
C
C
C
Steam
Steam temperature at steam drum

Steam temperature at SH primary inlet
Steam temperature at SH primary outlet
Steam temperature at SH secondary inlet
Steam temperature at SH secondary
outlet
Steam temperature at IBSH inlet
Steam temperature at IBSH outlet
7.9.1.3
Air
7.9.1.4
Air entering air heater

Air leaving air heater
Flue Gas
C
C
C
C
C
C
C
C
C
- 36 -
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Sl No
7.10
7.11
7.11.1
7.11.1.1
Description
Furnace outlet
Superheater inlet
Superheater outlet
Economiser inlet
Economiser outlet
Airpreheater inlet
Airpreheater outlet
Ash Cooler
Type
No. of coolers
Material of construction
Fuel Firing Equipment
Fuel Feeder (Coal)
Under feed for Coal
Unit
C
C
C
C
C
C
C
Type of feeder
No of feeders:
- Drag chain
- Drag chain
Drive details
Drive details
7.11.1.6
7.11.2
7.11.2.1
7.12
7.12.1
No.
tph
kW
kW
Fuel Oil Firing System
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Burners
- No. of burners
- Capacity per burner
- Type
- No. of lances
- Start-up oil consumption
- Location
- Fuel oil tank
Fuel Bunker
No.
kg/h
litres
m
Imported/Indigenous Coal Bunker

Bunker water volume
Elevation of top of bunker
No. of bunker
Dust Collector System
Overall size
Design gas flow
No. of fields
Thickness of casing
Thickness of hopper plate
Capacity of hopper
No. of hoppers
Collecting electrode :
- No.
*
m
m
No.
mxmxm
m3/s
No.
mm
mm
m
No.
- 37 -
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Sl No
7.12.2
Description
Unit
- Area
m
*
- Material
*
- Spacing
mm
*
Emitting electrode
*
- No.
*
- Material
*
- Spacing
*
Overall size
mxmxm
*
Specific collecting area
m/m/s
*
Probable supplier
*
Height of hopper bottom flange from
m
*
finished ground floor
Gas velocity
m/s
*
Residence time
min
*
Aspect ratio
*
Inlet dust concentration
gm/Nm3
*
3
Outlet dust concentration
mg/Nm
*
Holding capacity of hopper
*
- First field
m
*
- Second field
m
*
- Third field
m
*
- Fourth Field
m
*
Rating of HVR
*
- Voltage
kV
*
- Current
mA
*
MCC of ESP in Suppliers scope
Yes/No
*
Ash Characteristics at Hopper
*
Bed Ash Cooler #1 Outlet
*
- Ash density
kg/m
*
- Ash quantity
kg/h
*
Temperature of ash at outlet
C
*
No. of outlets
No.
*
Bed Ash Cooler #2 Outlet
*
- Ash density
kg/m
*
- Ash quantity
kg/h
*
C
*
No of outlets
No.
*
Economizer
*
- Ash density
kg/m
*
- Ash quantity
kg/h
*
C
*
No of outlets
No.
*
Air Heater
*
- Ash density
kg/m
*
- Ash quantity
kg/h
*
C
*
No of outlets
No.
*
ESP Field I
*
- 38 -
Sl No
7.13
7.13.1
7.13.2
7.14
7.14.1
Description
- Ash density
- Ash quantity
No. of outlets
Unit
kg/m
kg/h
C
No.
ESP Field II
- Ash density
- Ash quantity
No of outlets
ESP Field III
- Ash density
- Ash quantity
- Temperature of ash at outlet
No. of outlets
ESP Field IV
- Ash density
- Ash quantity
- Temperature of ash at outlet
No. of outlets
Feed Water System
Feed Pumps (Electro) with motors
Make
Type
Capacity
Head
Water temperature
NPSH
Inter stage bleed pressure
Drive motor
Recommended drive motor
- Rating
- Speed
Feed Control System Provided
100% MCR (Pneumatic)
30% MCR ( pneumatic )
100% MCR (Pneumatic)
Fans
Forced Draught Fans (for boiler)
Type of fan
Fan duty at MCR:
- Volume
- Head
- bKW
Installed parameters :
- Volume
- Head
Working temperature
- 39 -
kg/m
kg/h
C
No.
kg/m
kg/h
C
No.
kg/m
kg/h
C
No.
%
m/h
kg/cm2
C
m
kg/cm
kW
kW
rpm
Yes/No
Yes/No
Yes/No
%
m/s
mmWC
KW
m/s
mmWC
o
C
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Sl No
7.14.2
7.14.3
Description
Speed
Coupling
Recommended drive motor :
- Rating
- Speed
Efficiency of the fan
VFD included
Control damper :
- Type
- Actuator
- Location
Probable supplier
Induced Draught Fans (for Boiler)
Type of fan
Fan duty at MCR :
- Volume
- Head
- bKW
- Capacity
- Head
Working temperature
Speed
Coupling
- Rating
- Speed
VFD included
Control damper :
- Type
- Actuator
- Location
Probable supplier
Primary / Secondary Air Fans
Type of fan
Fan duty at MCR :
- Volume
- Head
- bKW
- Capacity
- Head
Working temperature
Speed
Coupling
- Rating
- 40 -
Unit
rpm
kW
rpm
%
Yes/No
%
m/s
mmWC
KW
m/s
mmWC
C
rpm
kW
rpm
%
Yes/No
%
m/s
mmWC
KW
m/s
mmWC
C
rpm
kW
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Sl No
7.14.4
7.15
7.16
7.17
7.18
7.19
Description
- Speed
Control damper :
- Type
- Actuator
- Location
Probable supplier
Chimney (Common for both Boilers)
Flue gas to be handled
Diameter of chimney
- at base
- at top
Height of chimney
Velocity of the exit of the chimney
Soot Blowers
Type
Quantity
Location and No.
Probable Supplier
Weight Schedule
Structures
Pressure parts
Non-pressure parts including auxiliaries
and ESP
Insulation and refractory
Piping
Total
Compressed air requirement :
- Volume (free air)
- Pressure
Type and Probable supplier for :
- Control damper actuators
- Control valves
- Oxygen analyser
- Field transmitter
Blow Down System
CBD tank
IBD tank
Provision of level control
Provision of motor operated valve
Chemical Dosing System
HP Dosing
- Preparation tank with agitator
- No. of pumps
- Material of construction
LP Dosing
Unit
rpm
%
Nm/hr
m
m
m
m/sec
No.
No.
t
t
t
t
t
m/h
ata
No.
No.
Yes/No
Yes/No
No.
No.
- 41 -
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Sl No
7.21
Description
- Preparation tank with agitator
- No. of pumps
- Material of construction
Terminal Points
For Steam
- Outlet of main steam stop valve/Non
return valve located near to boiler
columns.
Safety valve outlet piping upto
discharge to atmosphere.
- Outlet of vent pipe upto discharge to
atmosphere.
- Outlet of blow down tank.
CBD Exhaust at outlet steam stub on
tank
LP steam at inlet of deareator pressure
control valve inlet isolation valve.
For Feed Water
Unit
No.
No.
*
*
*
*
*
*
*
*
*
*
*
*
- DM water at the inlet of deaerator

level control station inlet isolation valve,
& at one point in Boiler area
For Condensate
- At the inlet of De-aerator nozzle
For Cooling/Service Water

- Inlet at an agreed single point (one
metre away from boiler boundary at
ground level).
- Outlet at nearest drain channel.
Flue gas
- Inlet of chimney
For Combustion Air
- Inlet to FD fan suction duct work.
- Inlet to secondary air fan/primary air
fan.
For Ash and Dust
Outlet of ash coolers for furnace
bottom ash.
- Outlet pipe work of ash hopper for
dust disposable
For Blowdown and Drains
- Outlet of blowdown tank to drain.
For HP and LP Chemical Dosing
- At an agreed point at ground level .
For Electrical Power
- Motor terminal
For Instrument Air and Plant Air
*
*
- 42 -
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Sl No
Description
- At an agreed single point (1 m away
from boiler boundary at ground level).
7.22
Exclusions
- RCC chimney
- Civil foundations
- Fuel preparation plant
- Fuels and chemicals
- Ash and dust disposal system
- Feed water treatment plant
- Interconnecting cables (power and
earthing)
- Lighting and socket outlets
- HT & LT PCC
- Distribution transformers
- DCS
- Registration of the boilers
- Certain site construction facilities as
subsequently defined
Unit
*
ANNEX II
SCHEDULE OF EQUIPMENT FOR ERECTION AND
COMMISSIONING
Sl.
No.
1
Item
Steam Drum
- Fully welded steam drum with manholes

- Steam drum internals
- Local water level gauges
- Remote water level gauge
2
Furnace
- Membrane panel water cooled enclosure
- Access doors/peep holes as required
- Air nozzles at furnace bottom
- Various openings/mountings as required
- Refractory, Refractory holding anchors etc., as required
Superheater
- 43 -
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Sl.
No.
Item
- Superheater tubes, inlet/outlet headers
Attemperator
- Direct contact spray type interstage attemperator

internals
Economiser
with spray nozzles and
- Economiser tubes/coils
- Economiser inlet/outlet headers
- Economiser casing with stiffeners
- Access door assemblies as required
- Economiser coils supports
6
Air Heater (Tubular)

- Air heater tubes, tube sheets
- Air heater casing with stiffeners
- Access door assemblies as required
Buckstays Assembly for Furnace/Boiler
Boiler, Economiser & Air-Heater Supporting Structure Jubilant scope

- Supporting structure from ground level (steel execution)
- Steel galleries/walkways,
gratings/chequered plates
staircases,
handrailings,
- Supporting structure for boiler roof

- Asbestos sheets for boiler canopy
- Supporting structure for boiler roof side sheeting
- Asbestos sheets for boiler roof sides
- Rust preventive painting (shop)
- Final painting (site)
9
Safety Valves
9.1 Steam Drum

- Spring loaded mechanical safety valves - 2 Nos.
- 44 -
toe
plates,
Sl.
No.
Item
- Exhaust piping above roof
- Drain piping
9.2 Superheater
- Spring loaded mechanical safety valve
- Exhaust piping above roof
- Drain piping
- Silencer on safety valve (80 dba @ 10 m distance)
- Motorised start-up vent valve with silencer
- Motorised main stop valve
- Motorised by pass valve
10
10.1
Water System
Feed Water (Drum Level Control Station)
- Feed water (drum level) control valve
- Isolation/bypass/drain valves
- Associated piping/fittings/hardware
10.2
Attemperator Spray Water Control Station

- Spray water control valve
- Isolation/bypass valves
- Associated piping/fittings/hardware
10.3
Only sampling Pipe work and No Coolers

- For Boiler feed water sampling
- For drum water/CBD sampling
- For saturated steam (from steam drum)
- For final superheated steam
10.4
11
11.1
Down Comer and Risers

Soot Blowers Not Required as per VENDOR
Steam Soot Blowers
- 45 -
Sl.
No.
Item
- Drive motors
- Auto sequential control panel
12
12.1
Integral Piping
Feed
- Feed pump discharge form deaerator outlet isolation valve to feed pump
suction
- Feed pump discharge to Feed control station
- Feed water control station to economiser inlet
- From attemperator spray water control station to spray water nozzle
- BFW pumping station to deaerator for minimum flow, blalancing line, and
leak of lines upto deaerator.
12.2
- From Economiser outlet to steam drum inlet

- AII recirculaiton piping involved in the feed water line and associated
isolation and regulation valve
Main Steam - Upto MSSV/NRV outlet
12.3
Auxiliary Steam
- Flash steam from CBD tank outlet to deaerator inlet
12.4
Vents
- From individual vent connections on steam drum, main steam
superheater, economiser upto safe elevation above roof
line,
- From outlet of safety valves/silencers upto safe elevation above roof

- From deaerator tank to atmosphere
12.5
Drain
- From individual drain points on drums, level gauges/ condensate pots,
safety valves, superheater/ economiser headers upto isolation valve on
common drain header
- Common drain header
- From CBD collection point on steam drum upto outlet of BD valve
- From common drain header upto BD tank inlet isolation valve
- Blowdown piping from BD valve to BD tank
- 46 -
Sl.
No.
Item
- From BD tank outlet to nearest drain at ground level
12.6
Cooling Water
- At one point in Boiler / ESP Area
13
13.1
Draught Plant
PA Fans 2 x 125% for boiler
- Fans with control damper, outlet isolation damper, base frame, foundation
bolts/holding down bolts, coupling and hardware
13.2
ID Fan - 2 x 60% MCR for boiler

- Fan with suction control dampers outlet isolation dampers,
foundation bolts/holding down bolts, coupling and hardware.
13.3
base frame,
FD Fan - 2 x 60% MCR for boiler

- Fan with control damper, outlet isolation damper, base frame, foundation
bolts/holding down bolts, coupling and hardware
13.4
13.4.1
Ducting and Hoppers

Ducting
- PA/SA fan suction
- From PA/SA fans' discharge upto air heater inlet
- From air heater outlet upto wind box
- From furnace outlet upto economiser inlet
- From economiser outlet to air heater
- From air heater outlet to ESP inlet
- From ESP outlet upto ID fan suction damper
- From ID fan outlet damper to chimney
- Associated dampers, expansion joints, stiffeners etc. as required
- Chimney (common for both the boilers)
13.4.2
Hoppers
- Hopper below
- 47 -
Sl.
No.
Item
- Economiser hoppers
- Air heater hoppers
- ESP hoppers
- Stiffeners, access doors
- Expansion joints as required
- Hoppers outlet slide gate
14
14.1
Fuel Feeding System

Coal (Imported coal, Indigenous coal,)- Jubilant
Coal Bunker with Supporting Structure and inside SS lining- Jubilant
- Isolation gate/Rod gate at outlet of bunker
- Feed chutes at inlet of fuel feeders
- Fuel feeders with supporting structure.
- Fuel feeder discharge chutes
- Drive electric motors for fuel feeders
- VFD for fuel feeders
- Couplings/hardware
14.5
Start-up fuel firing system with all auxiliaries and accessories
15
Ash
15.1
Bed
- Discharge pipe from bed upto inlet of (slide gates) cooler
- Bed ash coolers
16
Castable Refractory/Bricks as required for Boiler
17
Insulation and Cladding for :

- Boiler, superheater headers, drums
- Economiser, air heater
- Hot air/flue gas ducts
- 48 -
Sl.
No.
Item
- Hot water and steam pipelines for Supplier's scope of piping
18

-DCS & Field instruments as per list of instruments
- Air filter regulators, junction boxes, I/P converters, as required for above
instruments
- Instrument Air piping From Air filter regulator upto individual consuming
point
- Analyser (only O2)
-Control room instrumentation
- Control cabling upto junction box
19
Boiler Feed Water (BFWP) Pumping Station

- Electric motor driven BFW pumps with motors
- Coupling, hardware
- Base frame, holding down bolts/anchors
- Inlet/outlet isolation and non return valves
- Automatic minimum flow recirculation (ARC) valves
- Piping, mountings/fittings within BFWP station package
- Mineral wool insulation for package
- Aluminium cladding
- Final painting, wherever applicable By Jubilant
- Field instrumentation for BFWP package: transmitters, thermocouples
pressure/ temperature gauges, Local switches I/P converters etc
- Control room instrumentation for BFWP station package (DCS)
- Monorail arrangement and lifting hoist for pump and motor
20
Chemical Dosing System
20.1
High pressure (HP) dosing

- DM WATER piping
- Dosing tank
- 49 -
Sl.
No.
Item
- Dosing pumps
- Associated piping, valves, mountings, fittings within system
- Base frame, foundation bolts
- Piping From HP dosing pumping unit outlet to Inlet of HP dosing
connection on steam drum
20.2
Low Pressure (LP) dosing

- DM WATER piping
- Dosing tank
- Dosing pumps
- Associated piping, valves, mountings, fittings within system
- Base frame, foundation bolts
- Piping From LP dosing pumping unit outlet to Inlet of LP dosing connection
on feed line
21
21.1
Blow Down Tanks

Continuous blow down (CBD) tank (Common for both the boilers)
- Tank with associated stubs, nozzles, flanges, manhole
assembly etc.
- Mineral wool insulation
- Supporting structure
- Field instrumentation
- Control room instrumentation (DCS).
- Final painting (site) By Jubilant
21.2
Intermittent blow down tank (IBD)

- Tank with Associated stubs, nozzles, flanges, manhole assembly etc
- Mineral wool insulation
- 50 -
Sl.
No.
Item
- Supporting structure
- Field instrumentation
- Control room instrumentation.
- Final painting (site) By Jubilant
22
- Inlet/outlet transition pieces
- Inlet/outlet isolation dampers
- ESP inlet expansion bellow
- ESP outlet expansion bellow
- Electrostatic precipitator complete with discharge, collecting electrodes,
rapping devices, transformer rectifier sets, insulators
- ESP control panel, switchgear
- Power and control cables From MCC outlet terminal upto the ESP control
panel terminals and earthing system
- Outer casing on ESP duly covered by insulation and cladding
- Ash collection hoppers
- Rotary air lock feeders for hoppers
- Hopper heating system complete with control panel, power and control
cabling, switchgear, thermostats etc
- Complete supporting structure from ground level, including operating
platforms, staircases, handrails and toe plates
- Rust preventive painting
- Final painting (site) by Jubilant
23
SWAS for pH and conductives of feed water, drum water, saturated steam
and superheater steam- SWAS by Jubilant Connectivity and trial by Vendor
24
O2 analyser - On line
25
Chimney - Jubilant
- 51 -
Sl.
No.
Item
26
Civil
27
- Basic engineering for foundation, design and load details etc.equipmenmt

Load Data , GA Drawings , plan , elevation
Erection and Commissioning
- Erection and commissioning on turn key basis of VENDOR supplied items
- Supervision of erection and commissioning of the items even if in Jubilant
scope
Performance Parameters
COAL
1
Steam output of the Boiler for 24 Hrs &

365 days in a Year
TPH
65
Steam pressure at Boiler outlet
Ata
80
Steam temperature at Boiler Outlet
515 5
Steam temperature Range
60- 110
5
5.1
Boiler Thermal Efficiency

Boiler Efficiency with Indian Coal of
GCV 2997 Kcal/Kg
Boiler Efficiency with Indian Coal of
GCV 3800 Kcal / Kg
Boiler Efficiency with Imported Coal of
GCV 5700 Kcal / Kg
Aux. Power consumption of Boiler &
ESP
With VFD
Without VFD
Outlet Dust Emission Level
%
%
5.2
5.3
6
6.1
6.2
7
8
8.1
8.2
9
Deaerator Performance
Temp at outlet of deaerator
Oxygen content in water at the outlet of
deaerator
Steam Purity
- 52 -
%
%
KW
KW
Mg/N
m3
C
ppm
0
9.1
9.2
9.3
10
11
12
Thermal Conductivity at 25 0C , max

Silica
Dryness factor
Noise Level
Temp difference between
Insulation
surface & ambient
Efficiency Calculations
Ms/cm
ppm
%
dBA
0
C
0.2
0.02
*
85
20
ASME
PTC 4.1
The Break up of the power is to be provided by Vendor as below:

DESCRIPTION
SL.
NO.
QUANTITY
Total
01.
FD Fan motor
02.
ID Fan motor
03.
PA Fan
04.
Boiler feed pumps
05.
Drag chain feeders
06.
LP dosing pumps
07.
HP dosing pumps
08.
Motorised agitator
09.
ESP
Work
-ing
INSTALLED
MOTOR
CAPACITY
Stan
d
by
TOTAL
- WITH VFD
- WITHOUT VFD
- 53 -
KW /
Unit
Total
POWER CONSUMPTION AT EQUIPMENT

SHAFT DURING 100%
MCR WITHOUT
CONSIDERING MOTOR
EFFICIENCY AND
CABLE LOSSES (KW)
PENALTIES
In case there is delay in delivery beyond the schedule herein stated, penalty @ 0.5 % of
the order Valve shall be deducted from Vendor payment for each full week of delay
subjected to the maximum of 10% of the order value.
The following shall be the liquidated damages payable from the guaranteed figures
furnish by Vendor:
1. Rs 80,000.00 for every one (1) Kilowatt increases over the guaranteed value at
100% MCR Condition.
2. Rs 5,00,000.00 for every 0.1% decrease in Boiler Efficiency over the guaranteed
figure.
3. Rs 10,00,000.00 for every 2% reduction in steam flow over the guaranteed value.
4. Rs 5,00,000.00 for every 2 oC reduction in steam temperature at SH Outlet
- 54 -
Additional Points to be incorporated:

Electrical Points
1.The Boiler & ESP MCC shall be LT. The MCCs shall be as per Jubilant
Specifications.
2. The following parameters shall be considered while designing the LT System
2.1 Design Temp 50 Deg C.
2.2 Supply voltage variation +/- 10 %, Cycle +/- 5 % ,cumulative 10 %
2.3 Motors EFF1, class F insulation with temp rise of 75 Deg c. MCC suitable for
3ph ,4 wire , 415 v, 50 KA fault level.
2.4Degree of Protection IP-55
3. The Boiler & ESP MCC shall be located in the existing MCC Room
4.ESP MCC & TR sets shall have provision to hook up with DCS for monitoring
purpose.
5. Digital Energy meters shall be provided for ESP MCC & hook up to DCS
through soft acquisition protocol (RS485). All Major drive shall have remote
operation facility through DCS( Preferred make schneider). All MCC incomer
shall have energy meters with RS 485 comm.Protocol for data acquisition on
DCS
6. All motors above 200 KW shall be HT
7. In MCC all Siemens / Schneider make components shall be used.
- 55 -
Instrumentation Points
1.VENDOR shall supply bottom mounted bed temp thermo-couples as against
front mounted bottom thermocouples.
2. The design of the thermowell MOC shall be 1.5 times more than the operating
range.
3.Thermowell shall be screwed / threaded for connections down below instead of
welded to DP plate. Jubilant shall provide the drawing for the same.
4.Jubilant ahs asked for higher MP MOC for outer sheath and elements of
thermocouples than that of thermowells. VENDOR shall take care for higher MP
MOC for outer sheath and elements of thermocouples than that of thermowells
during detailed engineering phase.
5. The bed height measurement shall be based on air box pressure and remote
signal also. A flush mounted local gauges for all the six compartments to be
provided at burner floor instead of local mounted gauges. VENDOR shall provide
the draught gauges in addition to draft transmitter for air box draught
measurement.
6. VENDOR shall provide the control logic for DCS & FAT shall be attended by
VENDOR automation engineer for correctness of programmed logics.
7. All the temp elements shall be RTDS & Thermo-couples as per the application
suitability. All RTD for motor/ fan/pump bearing shall be headless type with 10
mtr Teflon insulated cable and tinned metal screen. All temp elements shall be with
thermowell. Thermowells for flue gas temp should have extra strength to prevent
problem of sagging/bending.
8. All the temp elements i.e. RTD & thermocouples shall be duplex type.
9. VENDOR shall provide flow switch in sealing water lines of BFW Pump.
10. VENDOR shall provide one pressure transmitter on Instt. Air Header.
11. All Control valves and RPCs shall be provided with the Smart Valve
Positioner, position feed back transmitter and PNP type proximity type switches
for close limit with desired level under fail safe operation.
12. VENDOR shall provide optical & galvanic isolation for all field analog signals
reporting to DCS shall be 24 V/ 4- 20 Ma.
13. All transmitters shall be smart with HART protocol of latest version. DP
transmitters must be provided with 5 way SS316 manifold and pressure
Transmitters with SS316 Isolation needle valve. Main isolating valve to be
provided at all tapping points especially for feed water and steam circuit.
- 56 -
14. The steam flow meter shall be Flow Nozzle type.

15.VENDOR shall provide 1 no additional Furnace pressure transmitter.
16. VENDOR shall provide level transmitter instead of Level switch for deaerator low level measurement.
17.VENDOR shall provide additional 1 no Steam Drum Pressure Transmitter.
18. The draft transmitter at Furnace and before economiser shall be used for
pressure drop measurement.
19. For solenoid operated instt , VENDOR shall meet the following requirements.
19.1 All open/ close valve should have open and close limit proximity switches for
status on DCS with local open/ close indication.
19.2 Pneumatic actuators shall be die cast Aluminium with suitability for open
installation of Elomatic or Amri/Neles make.
19.3 All electronic and electrical devices such as proximity, solenoid should be of
24 V dc with IP67 compliance.
19.4 All gang-mounted solenoids should be suitably grouped for different circuits
with facility of online repair and maintenance without affecting functioning of
others.
19.5 MOC of solenoid should be corrosion resistant.
19.6 All relays to be used with proximity should be of solid state type mounted in
safe area i.e. CR.
19.7 All SOPCs should be with supplied with reed switches for open-close status
to DCS with local LED indication . Make; FESTO/SMC/SHCENIDER
20. Vendor shall provide Motorised valves (start up vent only) and actuators with
position feedback to DCS with set of (2NO+2NC) potential free contacts for
Open, Close & torque limit contacts and LPBS having start, stop and emergency
push buttons. Starter shall be located in the MCC which is under JOL scope.
Actuator should have IP67 protection. Make ; Auma / Rotork.
21. VENDOR shall supply ESP TRCC control system shall be microprocessor
based controller with RS 485 connectivity facility to DCS for monitoring purpose
with following features
Remote start-stop and set point from DCS.
Remote monitoring signals i.e. 4-20mA for kV and mA to DCS.
All panel control wiring should be with tinned copper conductors only.
- 57 -
All electronics should have conformal coating for G3 compliance as per ISO
71.04.
22. VENDOR will provide pressure transmitter for measurement of pent house
pressure through purge air blower and RTD for temperature to DCS.
23. VENDOR shall supply high-level switches for ESP, APH, Economizer, ash
hoppers.
24. VENDOR will provide the fittings and impulse piping of the following
specifications
SS316 piping for Instrument air to AIR HEADERS.
MOC of air header X8 and 1/2' ball each distribution point should be SS316.
Air header should be provided with main isolating and drain valve.
A pressure gauge must be provided at all air headers.
NPT fittings and 12mm OD seamless SS316 impulse pipes must be used for
air distribution to individual instrument.
FRL to be provided at all pneumatic instrument.
Metal alloy Impulse piping with IBR grade isolating valves to be used for impulse
piping for transmitter for steam and feed-water circuit.
No where copper tubing or cu/brass fittings are to be used.
All steam line pressure gauges are to be provided with SS or alloy syphon and
snubber.
25. VENDOR to supply separate junction box for AI, A0, DI, D0, RTD &
thermocouple inputs. Also note that we have considered junction boxes of die
cast aluminium material of construction.
26. VENDOR shall supply VFDs with
Panel mounting/installation type.
Panel should be of RITTAL or better make
Panel should have sufficient number of cooling air circulation fans and detachable
type cartridge filters, tube light with door switch.
Each VFD should have isolating HRC fuses or MCBs in addition to common
MCCB.
Panel should be duly wired with ferruled terminal using tinned copper conductor.
All indication should be LED based.
Each drive should have local-remote selection switch, On-Off and Emergency
P.B. and local display and keypad for configuration and control.
Each VFD should give isolated output of 4-20mA for True RPM,KW and must
accept remote analogue set point and digital IOs for remote start, stop command
and run status.
27. VENDOR shall supply all the electronics DCS, PLC,VFDs,CONTROLLERS,
ANALYSER etc should have strict compliance to Conformal coating for G3 as
per ISA 71.04 &IP67 for open installation.
28. All local monitoring instruments should have MOC SS316/corrosion
resistant for pressure and temperature gauges with internal of SS304
- 58 -
29. VENDOR shall provide all necessary documents for I & C like Master I/O list
with instrument details, valve-sizing calculations, P&ID, instrument specification
sheet, instrument hook diagram,cable termination schedule, cable tray routing
with JB location diagram, process control and inter-lock logics and Control
system flow diagram during the detailed engineering stage.
30. Boiler start up & shut down, interlocks & protection logics shall be submitted
during detailed engineering stage by VENDOR.
LIST OF APPROVED SUB-VENDORS FOR BROUGHT ITEMS

MECHANICAL
1.
FANS
#
VENDOR
- 59 -
2.
FEED PUMPS
a.
b.
KSB
SULZER
3.
IBR VALVES
a.
b.
c.
KSB
BHEL
AUDCO
4.
BLOW DOWN VALVE
a. BHARAT HEAVY ELECTRICALS LTD

b. AUDCO
C. LEVCON
5.
BUTTERFLY VALVES
a. AUDCO
b. INTER VALVE
6.CONTROL VALVES
a.
b.
c.
d.
e.
f.
g.
7.
a.
b.
c.
d.
e.
f.
g.
DRESSER MASONEILAN
INSTRUMENTATION LIMITED
MIL CONTROLS
FISHER XOMOX
VALFLO
FORBES MARSHALL
FOURESS
PRDS
CHEMTROL / BTG
YARWAY
ARCA
FOURESS
IL
MIL
VENDOR (DESUPERHEATER)
8.BELLOWS (METALLIC)
a. VENDOR
9.CENTRIFUGAL PUMPS
a. KIRLOSKAR
b. KSB
- 60 -
10.PUMPS
a. AKAY
b. SULZER
c. KIRLOSKAR
11.RELIEF & SAFETY VALVES
a. AUDCO INDIA LTD
b. BHARAT HEAVY ELECTRICALS LTD
c. TYCO SANMAR
12.SPRING HANGERS
a. BHARAT HEAVY ELECTRICALS LTD
b. SARATHI
13.LUBE OIL SYSTEM
a. SOUTHERN LUBRICANTS
b. ALFA LAVAL
c. GRAND PRIX
14.SOOT BLOWERS
a.
b.
c.
BHEL
SITSON
RR Techno Mech
15.
FABRIC EXPANSION JOINTS
a.
b.
c.
KELD ELLENTOFT
BACHMANN
GBM
16.
DIRECT WATER LEVEL GUAGE
a.
b.
c.
YARWAY
CHEMTROL
LEVCON
17.
MINERAL WOOL INSULATION
a.
b.
c.
d.
MIN WOOL
LLOYD ROCK FIBRES
ROCK WOOL INDUSTRIES
ROCKWOOL INDIA (I) LIMITED
- 61 -
18.
ALUMINIUM CLADDING
a.
b.
c.
BALCO
INDAL
HINDALCO
19.
REFRACTORY & INSULATING BRICKS
a.
b.
c.
d.
e.
R.V. REFRACTORIES
ACC
CAST WELL INDUSTRIES
BASKAR REFRACTORY
DALMIA REFRACTORY
ELECTRICAL
1.
VARIABLE FREQUENCY DRIVE
a)
b)
c)
d)
e)
f)
L&T
SIEMENS
ALLEN BRADLEY
AMTECH
ABB
HIREL
2.
MOTOR CONTROL CENTRES
a)
b)
c)
d)
SIEMENS
L&T
GE POWER
ADVANCE CONTROLS
3.
XLPE CABLE TERMINATION KITS
a)
b)
CCI
M-SEAL
c)
d)
REYCHEM
Birla 3-M
4.
MOTORS
a) BHEL
b) SIEMENS
c) BHARAT BIJELE
5.
POWER & CONTROL CABLES
- 62 -
a)
b)
c)
d)
e)
f)
g)
h)
i)
6.
CABLE CORPORATION OF INDIA

UCL
NICCO
FORT CLOSTER
SPECIAL CABLES
TCL
RPG
POLYCABS
UNIVERSAL
TRANSDUCERS
a)
b)
c)
ABB
AE
SIEMENS
7.
LT SWITCHGEAR COMPONENTS
a)
b)
c)
SIEMENS
L&T
GE - POWER
INSTRUMENTATION
1.
AIR FILTER REGULATOR
a)
b)
PLACKA
SHAVO NORGEN (INDIA) PVT LTD
2.
FLOW NOZZLE / ORIFICE
a)
b)
c)
#
JN MARSHALL
MICROPRECISION PRODUCTS
IL (PALGHAT)
d)
VENDOR (ORIFICE)
3.
INDICATING METERS
d)
e)
AE
RISHAB
4.
INSTRUMENT CABLES
- 63 -
a)
b)
c)
d)
e)
f)
TCL
PARAMOUNT
CORDS
DELTON
THERMOPADS
ASSOCIATED
5.
INSTRUMENT TRANSFORMERS
a)
b)
c)
AE
GEC
KAPPA
6.
I/P CONVERTORS
a)
b)
c)
ABB
ROSEMOUNT
BELLS
7.
LEVEL GAUGES
a)
b)
LEVCON INSTRUMENTS PVT LTD

V. AUTOMAT
8.
OXYGEN ANALYSERS
a)
b)
c)
ROSEMOUNT
Yokogawa
ABB
9.
POWER CYLINDERS
a)
b)
c)
d)
#
10.
FISHER
INSTRUMENTATION LTD
KELTRON
BELLS
a)
b)
c)
d)
e)
ABB
ROSEMOUNT
TATA HONEY WELL
FUJI
YBL
11.
PRESSURE GAUGES
#
#
c)
#
a)MASS PRECESSION
b)WARRE
H. GURU
d)WIKA
PRESSURE & DP TRANSMITTER
- 64 -
12.
a)
b)
14.
PRESSURE SWTICH & TEMPERATURE SWITCHES

INDFOSS
SWITZER
13.
RTD AND THERMO COUPLES
a)
b)
c)
d)
e)
f)
GENERAL INSTRUMENTS
PYROELECTRIC
DETRIV
PYROTECH
NUTECH
TEMPSONS
SOLENOID VALVES
a)
b)
c)
d)
15.
ASCO
ROTEX
HERION
NUCON
TEMPERATURE GAUGES
a)
b)
c)
d)
e)
WAREE
MASS PRECESSION
GIC
PYROELECTRIC
H. GURU
16.
ALARM ANNUCIATORS
a)
b)
17.
MASSIBUS
PROCON
PLC
a)
b)
c)
d)
18.
ALLEN BRADELY
SIEMENS
TATA HONEYWELL
ABB
REMOTE PANEL MOUNTED INDICATORS
a)
b)
BELLS CONTROLS LIMITED

YOKOGAWA
- 65 -
19.
SINGLE LOOP CONTROLLERS

a)
b)
c)
d)
BELLS CONTROLS
SIEMENS LTD
TATA HONEYWELL LTD
YOKOGA BLUESTAR LTD
20.
SWAS
a)
b)
c)
d)
HACK ANALYSER
FORBES MARSHAL
FISHER ROSEMOMENT
ABB
- 66 -

Boiler Annex

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Boiler Annex

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Boiler Annex

Uploaded by

Copyright:

Available Formats

ANNEXURE- I

TECHNICAL SPECIFICATIONS, SCOPE, PERFORMANCE PARAMETERS,

1. SCOPE AND EXTENT OF SERVICES, TECHNICAL SPECIFICATIONS AND

Mixture of condensate and DM water

Temperature at inlet of deaerator

2. DESIGN CRITERIA OF BOILER

Firing Capability of Boiler on selected Fuels

As highlighted above, PURCHASER desires to burn Imported Coal, , the

Fuel shall be fed as underfeed during non-monsoon period. Supplier shall

Typical Characteristics of Fuels

For the performance evaluation the GCV shall be 6300 Kcal/Kg.

ERECTION AND COMMISSIONING ASISTANCE BY THE VENDOR

Boiler pressure parts consisting of

Protection shields for first row of economizer top/bottom banks shall be

Mountings and fittings

Fluidized bed combustion system of underfeeding systems

Coal bunker of 24 hrs storage capacity hopper with 2 mm SS lining for

Rod gate damper below all bunkers

Solid fuel firing equipment

Feed Chutes at inlet of Fuel feeders

Fuel Feeder discharge chutes

Dedicated VFDs for Fuel Feeders

Start-up fuel system

Fuel oil tank of Suitable Capacity

Surge hoppers below fuel bunkers

Provision for under bed firing of the Bio-Gas

Water cooled bed ash coolers

Electro Static Precipitator (ESP) , EMIGI Rapper type

ESP inlet/outlet expansion bellows

Ash door assemblies.

Air and flue gas fans and draught system

Two (2) Forced Draught (FD) fans (2 x 60%)

Two (2) Induced Draught (ID) fans (2 x 60%)

Two primary air fans (2 x 125%)

Motorized Valve as against manual valve at each feed pump discharge

All Blowdown second valve should be lever operated

Pneumatically operated bypass valve for FCV as against Motorized bypass

2 nos Bi-colour Multi-port direct water level gauges & 1 No hydrastep

Hydraulic type HP dosing pump and LP dosing pump

Silencer for FD Fan suction

Boiler MCC (Considering 2 x 60 %ID, FD fans, 2 x 125 % PA Fan, 2x 120 %

Draught gauges for Air Box compartments with panel

Flow switches in sealing water line of Feed pumps

Proximity switches for Control Valves, RPC & SOPC

Additional 1 no Furnace Pressure Transmitter

Level transmitter instead of level switch in Deaerator

Additional 1 no Drum Pressure Transmitter

SS316 of material for all impulse piping

Flame proof cable glands instead of Industrial area Cable Glands.

ESP hopper Heaters

Complete Structure, GI Grating, Platform, railing, tie beams, supports, Ash

Air & Flue Gas Ducting

All Dampers & expansion bellows

PA/SA fan suction

From PA/SA fan discharge up to air heater inlet

From Air heater outlet up to wind box

From furnace outlet up to economiser inlet

From economiser outlet to air heater