This manual was developed by representative members of the

Architectural Metal Products Division (AMP) of the National Association

of Architectural Metal Manufacturers (NAAMM) to provide their opinion
and guidance on the design and specification of fixed metal stairs. This
manual contains advisory information only and is published as a public
service by NAAMM and its AMP Division. NAAMM AND ITS AMP
DIVISION DISCLAIMS ALL LIABILITY OF ANY KIND FOR THE USE,
APPLICATION OR ADAPTATION OF MATERIAL PUBLISHED IN THIS
MANUAL.

Library of Congress Catalog Card Number: 82-80128

Copyright 1959,1971, 1974,1982,1992
National Association of Architectural Metal Manufacturers
All Rights Reserved

METAL STAIRS MANUAL

FIFTH EDITION

Publishedanddistributedbythe

NATIONAL ASSOCIATION OF ARCHITECTURAL METAL MANUFACTURERS

600 SOUTH FEDERAL STREET .......................................................................................... CHICAGO, ILLINOIS 60605

C0NTENTS
GENERAL INFORMATION .......................................... Section 1
Introduction
Advantages of Metal Stairs
Classification of Stairs
Design Factors Affecting Stair Costs
INSTALLATIONS REPRESENTATIVE
OF STAIRS MEETING NAAMM
MINIMUM STANDARDS ............................................. Section 2
Photographs and Details:
Straight, Circular, Spiral, Winder,
Alternating Tread Stairs and Ship's Ladders
INSTALLATIONS REPRESENTATIVE
OF CUSTOM DESIGNED STAIRS .............................. Section 3
Photographs and Details:
Straight, Curved and Circular Stairs
CONSTRUCTION DETAILS ........................................ Section 4
Stair Dimensions
Stringers, Treads and Risers, Nosings, Platforms
Soffits, Newels and Railings, Handrails
Handrail Brackets, Fastenings and Terminals
STRUCTURAL DESIGN AND DATA ........................... Section 5
Design Examples:
Stair Framing and Railings
Engineering Data:
Load-Deflection Tables for
Stringers, Risers, Treads and Platforms
Properties of Stair Railing Sections
RECOMMENDED VOLUNTARY
STANDARDS AND GUIDE
SPECIFICATIONS ........................................................ Section 6
GLOSSARY OF TERMS .............................................. Section 7

FOREWORD
The first edition of the NAAMM Metal Stairs Manual was published in 1959 and proved to be one of the most widely used of all NAAMM
publications. The second edition, published in 1971, contained much more data than the first edition, while the 1974 edition had only a few
minor revisions.
The 1982 fourth edition underwent extensive revisions. The section on representative installations was divided into two sections, one of which
illustrated stairs meeting NAAMM minimum standards; while the other illustrated custom designed stairs with special aesthetic effects. Also
added was a new section containing recommended voluntary minimum standards for fixed metal stairs and guide specifications for the
architect.
This 1992 edition of the NAAMM Metal Stairs Manual, like its predecessors, should be extremely helpful to architects, engineers and
manufacturers. New design examples include an aluminum stairway and a ship's ladder. Photographs of several outstanding architectural
designs have been added, and the section on construction details has been updated and expanded.

ACKNOWLEDGEMENTS
The committee responsible for the preparation of this revision of the NAAMM Metal Stairs Manual thanks all members of the Association who
have assisted with this work.
NAAMM recognizes the American Institute of Steel Construction for the use of the table of steel channel properties and the Aluminum
Association for the use of the table of aluminum channel properties.
The editor of the fifth edition was Jack Roehm, a past president of NAAMM, who retired as Technical Director in 1991. All members of the
Association appreciate his input to this document as well as his years of service to NAAMM.

S E C T IO N 1

GENERAL INFORMATION
C0NTENTS
Introduction ............................................................................................1-2
Advantages of Metal Stairs ....................................................................1-3
Classification of Stairs ............................................................................1-5
Design Factors Affecting Stair Costs ......................................................1-8

INTRODUCTION
Since prehistoric times, the stairway has provided the only means of moving, under one's own power, from one level to another
in a building, within optimal limits of space, effort and safety. Even in buildings having elevators or ramps, stairs, too, are
provided as a safeguard to the occupants in times of emergency. They are an essential building element, taken for granted in
any multi-storied building. But stairs don't just happen; to best serve their purpose they must be correctly designed and
properly built.
For centuries stairs have been made of stone masonry and wood. Metal stairs, by comparison, are a relatively new
development. We're not sure when they first appeared, but quite likely the metal first used was wrought iron. By the time cast
iron came into use for building facades, in the 1830's, its use for stair construction had probably also been explored, and
perhaps was already well developed. Cast iron stairs became increasingly commonplace with various improvements and
added embellishments from time to time, during the next hundred years, in many public and commercial buildings. With their
paneled newels and their moulded and ornamented stringers, these heavy cast iron stairs are still in use in many of our older
structures. As late as the early 1930's they were still being specified by the Treasury Department in its new post office
buildings, and during those depression years, as many will recall, government building constituted a large share of our
construction activity. Many of today's metal stair manufacturers began their operations during this cast iron era. But gradually
this heavy cast iron, with its inflexibilities and its high production labor costs, gave way to much lighter, more efficient and less
expensive steel as a more-logical material for stair construction, and by the 1920's many stairs were being built of steel.
During the past 70 years the techniques of steel stair construction have, in turn, undergone many changes, steadily improving
and taking full advantage of technical developments as they have occurred. Rolled sections are now made of stronger steel;
improved sheet material and modern forming methods have increased the use of cold formed section; and welding has
replaced bolted connections in many cases. With the availability of suitable copper alloys and the growing use of aluminum
and stainless steel in building construction, the use of non-ferrous metals has greatly increased the scope and the design
potentials of metal stair construction.
As everyone knows, there are many kinds of stairs, serving a wide range of purposes. They may be purely functional or
utilitarian, built at minimal cost, or they may be highly decorative architectural features, using the most expensive materials.
Most stairs, of course, are of a quality that lies somewhere between these two extremes. But the design potentials of metal
stair construction are limited only by the architect's ingenuity.
It is the purpose of this Manual to provide architects with comprehensive up-to-date information on the design and construction
of metal stairs of all types. Section 2 illustrates with photographs and principal details, installations representative of metal
stairs which meet NAAMM minimum standards. Section 3 illustrates with photographs and principal details installations
representative of metal stairs custom designed to achieve esthetic effects as well as to serve the functional needs of the
building. Section 4 provides information on construction details and contains details of all parts of typical construction. Section
5 provides examples illustrating the structural design of stairs and railings as well as engineering data on stair components.
Section 6 presents recommended voluntary minimum standards for fixed metal stairs and guide specifications for the
architect. Section 7 is a glossary in which will be found the definitions of terms commonly used in stair work.
The stair designs shown, as well as their accompanying details, are intended only as suggestions - examples of what may be
done with metal stair construction. Generally speaking, the architect should be concerned, in his drawings, with conceptual and
structural designs and the provision of sufficient details to clearly explain the materials to be used and the esthetic effect
desired. If he provides complete details of all structural parts and their connections, such details must meet not only the load
requirements but also their dimensional requirements and tolerances as specified in the governing codes and as may be
specified for special conditions which may exist for certain installations. Special conditions may include government
requirements for occupational safety or for physically handicapped persons. Detailing is often left to the fabricator, and will be
shown on the shop drawings which he submits for the architect's approval. Although metal stairs of all types are essentially
custom designed, each stair manufacturer has his own preferred and proven methods of fabricating typical repetitive parts,
especially on the more common types of stair. What may be the best detail or connection method in the opinion of one
manufacturer is not necessarily consistent with the practices of another. And when the archi

tect is contemplating the use of special design features, he should contact one or more fabricators early in the
design stage to avail himself of any suggestions which may result in better or more economical design. However,
the architect or engineer responsible for the design must verify that details, connections, materials, etc., proposed
by the manufacturer are structurally adequate and meet all of the requirements of the specifications.
ADVANTAGES OF METAL STAIRS
In designing most types of buildings, the architect has a choice of several materials for use in stair construction.
Except in wood frame structures, he frequently chooses metal, because metal stairs offer certain advantages
over those built with other materials. Among the more important of these advantages are the following:
Design Versatility
Metal is one of the most versatile building materials. It can be formed in many different ways, accepts an infinite
variety of finishes, can provide almost any esthetic effect desired, and is compatible in appearance with all other
architectural materials. Metal is appropriate for stairs of all kinds, from the purely functional service types to the
most elaborate architectural types. It serves equally well for a simple straight-run stair or for the most complex
and graceful curved stair. Whatever the architect's design calls for, it can be faithfully reproduced in metal, with a
virtually unlimited latitude in the design of all major elements.
High Strength-to-Mass and Strength-to-Weight Ratios
Although the density of metal is higher than that of other stair materials, its strength is greater by a much larger
ratio. Hence the sectional areas of metal stair members are much smaller than those needed if other materials
are used. This high strength-to-mass ratio of metal is a valuable asset in situations where headroom or floor
space is Iimited, because the structural members are of minimal size. In high-rise buildings especially, the saving
of weight provided by metal stairs because of the high strength-to-weight ratio may also be an important
consideration inasmuch as it reduces the amount of foundation work and framing required.
Accurate Dimensional and Quality Control
The safety of the user is always of paramount concern in any type of stair, and to a large degree safety depends
upon the uniformity of riser and tread dimensions and the construction of railings. Metal stairs are shop fabricated
under careful supervision, using the most modern tools and equipment. Their dimensions are carefully controlled,
in accordance with the architect's design, and are held with in close tolerances to provide true and uniform lines
and faithful reproduction of design. This degree of accuracy cannot be economically achieved by the field
construction methods used in building stairs of other materials.
Integral Railing Construction
One of the most important attributes of metal stair construction is the dependable stability of its railings. With
other types of stair construction, field measurements are usually required, separate railing shop drawings must be
made, and after fabrication the railing is delivered and installed as a separate entity. In the meantime temporary
railings are often required. This is not the case with metal stairs. Railings are accurately fitted to metal stairs in the
shop and, whenever feasible, are firmly secured in place and the stair is delivered as a complete unit. The more
elaborate types of railing are also shop fitted, but may be shipped separately to be installed in the field as an
integral part of the stair. Thus metal stairs offer the advantage of unified construction under a single responsibility,
as opposed to the more complex and costly process of dealing with, and correlating the work of several different
trades.

Early Availability
Because metal stairs are completely fabricated offsite, their manufacture is independent of construction progress
at a building site. They are ready for installation whenever they are needed and building construction permits, and
may be installed complete with railings as required. After installation the stair may be used immediately by
workmen, eliminating the cost and safety hazards of temporary ladders, stairs and railings. Additional safety is
realized because the toe plate forms a curbing at all open ends and open back edges of treads and prevents
small tools and miscellaneous items from rolling off and causing possible injury to workmen below.
Metal stairs of the types commonly used in multistoried buildings may also be pre-assembled in the shop and
delivered to the building site as prefabricated units. Such units may then be installed and ready for use even
before the surrounding building frame is erected, providing even greater economies of time and cost.
Rapid Installation
Regardless of what type a metal stair may be, its installation usually requires much less time than that required
for stairs of other materials. Under normal circumstances installation is simply a process of assembling prefitted
parts wholly fabricated in the shop, and a minimum of field labor is required.
Economy
A true comparison of costs must take into account not only the price of the product in question, but also all of the
costs affected by, or resulting from, the use of this product. Not only are metal stairs, per se, highly competitive in
cost with stairs of other materials, but their use results in contingent economies which are often substantial. Metal
stairs, though custom built, are usually constructed of sections that are readily available from stock or local
warehouse. In most cases a minimum of detailing by the architect is required.
This results in a saving of time and cost to both architect and client. Because of the early availability and rapid
installation of metal stairs, the cost of temporary stairs and railings in the building during construction is
eliminated. And the time required for supervising, correlating and expediting the stair construction work is reduced
by having the stair and railing both installed under a single responsibility.
Salvage Value
In some situations the salvage value of stairs may be a consideration. Metal stairs of the more common types can
be dismantled, moved to another location and re-installed when building alterations are required. And finally,
when they have served their purpose, and the building is demolished, metal stairs have scrap value.

CLASSIFICATION OF STAIRS
With its 1971 Edition of the Metal Stairs Manual, NAAMM published for the first time a system of classifying stairs.
It was believed that a logical classification system would reduce the confusion which existed in the terms used to
refer to the different types of stairs and would be helpful to architects, engineers, manufacturers and all
concerned. In the intervening years this has proven to be the case. It was published again, unchanged, in the
1982 (Fourth) Edition of the Manual. The NAAMM system has been accepted by the stair industry.
Under the NAAMM system, metal stairs are classified according to both Type and Class. The Type designation
identifies the physical configuration or geometry of the stair, while the Class designation refers to its construction
characteristics - the degree of refinement of fabrication and finish - and to the general nature of its usage.
Obviously, the Type designations are applicable to stairs made by any material, but the various Classes, as here
described, apply more particularly to metal stairs.
Types of Stairs
The four types of stairs classified in the system described in the two previous editions of the NAAMM Metal Stairs
Manual are Straight Stairs, Circular Stairs, Curved Stairs and Spiral Stairs. Description of two other types of
stairs, Winder Stairs and Alternating Tread Stairs, have been added to this fifth edition of the Manual. One type of
ladder, namely Ship's Ladder has also been added. The representative installations shown in Sections 2 and 3 of
the Manual illustrate these items. This listing of types is not necessarily allinclusive but it represents the great
majority of stairs. It is not uncommon to find two or more types, represented in the same stair, and in rare cases
there may be found a stair which properly falls in none of these type categories.
The Workmen's Compensation Bureau has made the following recommendations for pitch of ramps, stairs and
ladders:
Ramps: Pitch ranges from 0 to 20.
Preferred maximum pitch: 15.
Stairs: Pitch ranges from 20 to 50.
Preferred maximum pitch: 35.
Ladders: Pitch ranges from 50 to 90.
Preferred maximum pitch: 75.
Pitches close to the maximum angles should be avoided wherever possible as they
are uncomfortable and could be unsafe.
Straight Stairs are by far the most common type, representing the bulk of the stair
market. Though the term "straight" is self-explanatory, for purposes of classification a
straight stair is defined as one in which the stringers are straight members. Straight
stairs, unlike stairs of the other three types, may be arranged in several different
ways:
a) Straight run: either a single flight extending between floors, as shown in "A" at the
right, or a series of two or more flights in the same line, with intermediate platforms
between them, as shown in "B".
b) Parallel: successive flights which parallel each other and are separated only by
one or more intermediate platforms, as shown in "C".
c) Angled: successive flights placed at an angle of other than 1800 to each other
(often 900), with an intermediate platform between them as shown in "D" or "E". The
type shown in "D" at the right is often referred to as a "trussed" stair.

d) Scissor: a pair of straight run flights paralleling each other in plan and running in opposite directions on
opposite sides of a dividing wall, as shown in "F".
Circular Stairs are stairs which, in plan view, have an open circular form, with a single center of curvature. They
may or may not have intermediate platforms between floors.
Curved Stairs are stairs which, in plan view, have two or more centers of curvature, being oval, elliptical or some
other compound curved form. They also may or may not have one or more intermediate platforms between floors.
Spiral Stairs are stairs with a closed circular form, having uniform sector shaped treads and a supporting center
column.
Winder Stairs in plan view are parallel or angled. However, unlike straight stairs, no platforms are used where
the 1800 angle occurs for the successive flights of parallel stairs, nor are platforms used for successive flights
placed at angles other than 1800 (often 900). Instead, the stairs continue to rise through the angled areas with
sector shaped treads having the same riser heights as the straight part of the stair.
Alternating Tread Stairs are an exception to the upper pitch limitation for stairs. In this type of stair the treads
are alternately mounted on the left and right side of a center stringer. Because of this tread construction and the
use of handrails on each side, these stairs permit safe descent facing outward from the stair. Generally, pitch
angles used in these stairs will range from 56 to 68.
Ship's Ladders generally have pitch angles ranging from 59 to 75. They require flat treads and handrails on at
least one side, depending on stair width.
Pre-assembled and Pre-erected Stairs are stairs whose components are assembled in the plant to make up
units of varying sizes and degrees of complexity. These may be platform units, flight units, combination platform
and flight units, or larger units comprising the complete floor-to-floor story-height stair. Pre-assembled stairs may
be of the architectural class, but pre-assembly methods are commonly applied to stairs of the commercial and
service classes because of the repetitive use of identical units. Pre-assembled units for multi-storied buildings
may be designed to be self-supporting so that they may be pre-erected on the building site. Such units can be
stacked one upon the other and field-connected to form stair towers. Stair towers can be erected and ready to
use prior to erection of the surrounding building structure. The use of preassembled units and pre-erected stair
systems usually effects considerable savings and expedites the construction of buildings.
Classes of Stairs
The Class designation of stairs, is a key to the type of construction, the quality of materials, details and finish and,
in most cases, the relative cost. As stairs of all classes are built to meet the same standards of performance in
respect to load carrying capacity and safety, these class distinctions do not represent differences in functional
value, but in character and appearance. It is important to recognize that where function is the prime concern,
and esthetics are of minor importance, significant economies can be achieved by specifying one of the less
expensive classes. Detailed information on this matter of potential economies in design is provided in the fourth
part of this section of the Manual.
The following descriptions indicate the general construction characteristics of each class, but it should be
recognized that because each manufacturer has his own preferred methods of fabrication, the details of
construction vary somewhat throughout the industry. The four classes of stairs, listed in the order of increasing
cost (as a general rule), are described as follows:
Industrial Class: Stairs of this class are purely functional in character and consequently they are generally the
most economical. They are designed for either interior or exterior use in industrial buildings such as factories and
ware

houses, or as fire escapes or emergency exitways. They do not include stairs which are integral parts of industrial
equipment.
Industrial class stairs are similar in nature to any light steel construction. Hex head bolts are used for most
connections, and welds, where used, are not ground. Stringers may be either flat plate or open channels; treads
and platforms are usually made of grating or formed of floor plate, and risers are usually open, though in some
cases filled pan type treads and steel risers may be used. Railings are usually of either pipe, tubing, or steel bar
construction.
When used for exterior fire escapes the details of construction are similar, except that treads and platforms are of
open design, usually grating or perforated floor plate. Also, the dimensions, methods of support and other details
are usually dictated by governing code regulations.
Service Class: This class of stairs serves chiefly functional purposes, but is not unattractive in appearance.
Service stairs are usually located in enclosed stairwells and provide a secondary or emergency means of travel
between floors. In multi-storied buildings they are commonly used as egress stairs. They may serve employees,
tenants, or the public, and are generally used where economy is a consideration.
Stringers of service stairs are generally the same types as those used on stairs of the industrial class. Treads
may be one of several standard types, either filled or formed of floor or tread plate, and risers are either exposed
steel or open construction. Railings are typically of pipe construction or a simple bar type with tubular newels, and
soffits are usually left exposed. Connections on the under side of the stairs are made with hex head bolts, and
only those welds in the travel area are smooth.
Commercial Class: Stairs of this class are usually for public use and are of more attractive design than those of
the service class. They may be placed in open locations or may be located in closed stairwells, in public,
institutional or commercial buildings.
Stringers for this class of stairs are usually exposed open channel or plate sections. Treads may be any of a
number of standard types, and risers are usually exposed steel. Railings vary from ornamental bar or tube
construction with metal handrails to simple pipe construction, and soffits may or may not be covered. Exposed
bolted connections. in areas where appearance is critical are made with countersunk flat or oval head bolts;
otherwise hex head bolts are used. Welds in conspicuous locations are smooth, and all joints are closely fitted.
Architectural Class: This classification applies to any of the more elaborate, and usually more expensive stairs;
those which are designed to be architectural features in a building. They may be wholly custom designed or may
represent a combination of standard parts with specially designed elements such as stringers, railings, treads or
platforms. Usually this class of stair has a comparatively low pitch, with relatively low risers and correspondingly
wider treads. Architectural metal stairs may be located either in the open or in enclosed stairwells in public,
institutional, commercial or monumental buildings.
The materials, fabrication details and finishes used in architectural class stairs vary widely, as dictated by the
architect's design and specifications. As a general rule, construction joints are made as inconspicuous as
possible, exposed welds are smooth and soffits are covered with some surfacing material. Stringers may be
special sections exposed, or may be structural members enclosed in other materials. Railings are of an
ornamental type and, like the treads and risers, may be of any construction desired.
General Requirements, All Classes of Stairs
All fixed metal stairs, regardless of class, are of fire resistant construction and are designed and constructed to
carry a minimum live load of 100 pounds per square foot of projected plan area or an alternative concentrated
load of 300 pounds applied at the center of any tread span. Railings and handrails are designed and constructed
to withstand a minimum force of 200 pounds applied vertically downward and horizontally in a perpendicular
direction at any point on the top rail. Complete suggested requirements for alI classes of stairs can be found in
the Recommended Voluntary Minimum Standards for Fixed Metal Stairs in Section 6 of the Manual.

Use of the Classification System

When using the system, both the Type and Class of stair should be stated. A stair design may readily be
identified as, for example, a "straight parallel stair, commercial class", a "curved stair, architectural class", or a
"spiral stair, service class". It should be recognized that some types of stair are necessarily made in only one or
two classes of construction. Generally, the classes normally applicable to each type are as follows:
Straight stairs - all classes
Circular stairs - usually architectural class but may be commercial, service or industrial class
Curved stairs - architectural class only (always specially designed)
Spiral stairs - usually service or industrial class, but may be commercial or architectural class.
Winder stairs - all classes
Alternating tread stairs - industrial class
Ship's ladder - industrial class
Pre-assembled and pre-erected stairs - all classes
DESIGN FACTORS AFFECTING STAIR COSTS
This Manual is intended not only to stimulate the designer's imagination but also to encourage the appropriate
and efficient use of materials and labor in stair construction. The interests of all concerned are best served when
the stair is so designed and specified as to properly fulfill its intended purpose, yet provide maximum value
received per dollar of cost. The following suggestions are offered as ways of avoiding unnecessary costs without
sacrificing essential values. They deserve careful consideration, especially in the design of commercial and
service class stairs in multi-storied buildings.
1. Stair Flight Construction
Especially on flights of relatively short run or narrow width, the load carried by the stringers should be checked to
see that stringers are not oversized. On many stairs a 10" channel weighing 6.5 lb./ft. may be adequate, in place
of one weighing 8.4 lb./ft.
The use of plate stringers may sometimes effect savings, but in evaluating this possibility, the method of providing
rail connections must be considered. Open channel stringers are generally cheaper than boxed stringers, and, for
obvious reasons, straight stringers cost much less than curved stringers.
The welding of treads and risers directly to stringers (unit construction) will eliminate the need for carrier angles or
bars and will sometimes reduce costs, but such construction should be used only when practically feasible. As
welds are made on the upper side of a pan type tread, they are covered by the tread fill. The use of floor plate or
tread plate for treads and risers usually results in maximum economy, as the need for tread fill is eliminated.
2. Platform Construction
The provision of a base or curb around platforms by exposing the upper part of the stringers above the platform
floor increases costs. A structural

frame with platform pan construction and fill on top of it is less expensive and often provides a satisfactory
construction. Still further economy can be achieved by the use of a floor or tread plate platform, rather than pan
construction and fill, where this type of construction is acceptable.
3. Railings
An economical type of rail for a stair is a steel pipe or tube rail connected at the ends by standard terminal
castings to a square or rectangular tube newel. This construction provides rigid support at both ends of a flight,
yet permits minor installation adjustments, where necessary, at floors and platforms.
The use of square or rectangular tube for the railing, in place of pipe, provides an alternative at slightly higher
cost.
The use of continuous rails without interruption by newel posts or other obstructions, along the fIight of the stairs
and at floors and platforms between flights, as presently required by codes for most types of construction,
increases the cost. However, it does improve the safety of stairs and facilitates their use by persons with certain
physical handicaps.
Often, on relatively short flights, the need for intermediate posts on pipe rails can be eliminated by substituting a
larger size pipe. This also reduces cost.
4. Connections and Finishing Work
The use of hex head bolts in place of flat or oval head bolts eliminates the necessity of countersinking and speeds
stair assembly. Where appearance is not critical, welding neatly done but not ground smooth, provides maximum
rigidity at minimum cost. The use of flat or oval head bolts, the grinding of welds and the complete removal of all
sharp edges and burrs only on the travel surface and wherever they may be a hazard to stair users will result in
some savings.
5. Expediting Installation
Metal stairs can usually be installed earlier in a steel framed structure than in one having a concrete frame.
Because the erection tolerances in the steel framing around the stairwell are minimal, the stairs can be detailed,
shop drawings can be prepared and approved and the stairs can be fabricated before the building frame is
erected. In conventional practice the metal stairs can then be installed as soon as the frame is in place. Or, if
some of the larger pre-assembled units are used, the stairs may be installed in place, completely self-supporting,
before erection of the building frame. In any case, delays to subsequent construction are eliminated and overall
construction costs are minimized.
If the building has a concrete frame, the stair fabricator can supply the contractor with the necessary detail
drawings showing critical dimensions to be maintained, and if maintenance of these dimensions is guaranteed, he
can proceed with fabrication so that the stairs can be installed as soon as forms are removed and the stairwell is
cleared. Because of the probability of greater dimensional variations in a concrete frame than in a steel frame,
consideration should be given to using tube newel railing construction which permits installation adjustments.
When stairs cannot be installed until walls are in place, the contractor should locate and set all anchors and
anchor bolts, provide recesses and pockets in floors and walls, and fill in such recesses and pockets after the
stairs are installed, all in accordance with the approved shop drawings. Of course it's his responsibility, too, to see
that stairwells are cleared of all debris and interference before the installation begins.
When considered individually, these potential ways of reducing stair costs may not seem very significant, and the
savings on a small job may not be very large. But collectively, and especially when applied to installations in
multi-storied buildings, they can result in substantial economies.

SECTION 2
INSTALLATIONS REPRESENTATIVE OF STAIRS MEETING NAAMM MINIMUM STANDARDS
Photographs and principal details of a number of stairs, typical of those made by NAAMM member companies,
are presented in this section of the Manual. Examples of all of the common types and classes of stairs are
included. These types of stairs are readily available. They are fabricated from standard components and
materials and installed in accordance with the practices developed by the metal stair industry over many years.
These stairs meet minimum standards recommended by NAAMM. However, because the design of stairs is
controlled by building codes, the designer is advised that, should designs similar to any of those illustrated be
considered for use, certain modifications may be necessary to conform to governing code requirements.
NOTE: In each case the descriptions given apply only to the stair shown.
CONTENTS
Straight Stair: Parallel, Wire Mesh Panels 2-2
Parallel, Industrial 2-3
Parallel 2-4, 2-5
Straight Run, Industrial 2-6
Angled 2-7
Scissor 2-8
Parallel, Split-landing, Pre-assembled .... 2-9
Parallel, Pre-erected, Stacked 2-10
Circular Stair: Industrial 2-6
Spiral Stair: ........................... 2-11, 2-12, 2-13
Winder Stair: ................................... 2-13
Alternating Tread Stair: 2-14
Ship's Ladder: .................................... 2-15

DESCRIPTION
Stringers - Steel channels.
Treads and Risers - Sheet and steel.
Railing - Steel pipe mounted on stringers with
framed woven wire panel attached by welding at
all posts and rails.
Finish - Painted.

DESCRIPTION
Stringers - Structural steel channels.
Treads - Steel pans, concrete filled.
Platforms - Steel sheet deck, concrete
filled.
Railing - Steel pipe, welded to posts.
Finish - Steel painted.

DESCRIPTION
Stringers - Structural steel channels.
Treads - Formed steel sheet, concrete
filled.
Risers - Formed steel sheet, exposed.
Platforms - Steel sheet deck, concrete
filled; flight headers and platform
headers structural channels; both
suspended on hanger rods.
Railing - Steel pipe, welded.
Finish - Steel painted.

DESCRIPTION
Stringers - Structural steel
channels.
Treads Steel floor plate.
Risers Steel sheet.
Platforms - Steel floor plate; flight
headers structural steel channels;
intermediate, supports steel bars at
id-point, steel bars at plate edge.
Supported by hanger rods.
Newels - Square steel tubing,
welded to face stringers at
platforms.
Railing - Steel pipe welded to
newels.
Wall Handrail - Steel pipe, malleable
iron brackets.
Finish - Steel painted.
NOTE: Check governing code for rail spacing requirements.

DESCRIPTION
Stringers - Structural steel channels.
Treads - Floor plate formed with nosing and
back edge stiffener.
Railing - Steel pipe, welded, connected to
stringer by U-bolts.
Finish - Steel painted.

DESCRIPTION
Stringers - Structural steel channels
welded or bolted to newels.
Treads - Formed steel sheet,
concrete filled.
Risers - Steel sheet exposed.
Platform - Steel sheel with ribs,
concrete filled. Structural steel
channel flight headers continuously
welded to face stringers and bolted
to wall stringers.
Newels - Square steel tubing, capped
both ends.
Railing - Steel pipe handrail. Square
steel bar balusters welded to top and
bottom steel channels, or parallel
steel pipes welded to newels.
Wall Handrail - Steel pipe on
malleable iron brackets.
Finish - Steel painted.
NOTE: For steel bar baluster guardrails side-mounted handrails are recommended.

DESCRIPTION
Stringers - Structural steel channels.
Treads Steel sheet. Concrete filled.
Risers Steel sheet exposed.
Wall Handrail - Steel pipe on brackets, both sides of each flight.
Finish - Steel painted.

DESCRIPTION
Stringers - Structural steel channels.
Treads and Risers - Formed steel
sheet. Treads concrete filled. Risers
exposed. May be open risers with floor
plate or grating.
Landing - Steel sheet pans with welded
angle stiffeners. Pans concrete filled.
Newels -Square steel tubing.
Railing - Square steel tubing. May be
continuous around newel.

DESCRIPTION
Stair Stringers - (A) Structural steel channels.
Treads and Risers - (B) Formed steel sheet,
concrete filled.
Headers - (C) Structural steel channels.
Platform Support - (D) Structural steel I-beam.
Newel - (E) Square steel tubing.
Metal Deck - (F) Ribbed steel sheet.
Temporary Bracing - (G) Steel angles.
Temporary Bracing - (H) Steel pipe.
Railing - (1) Balusters welded to flat bar, top
and bottom. Steel pipe railings.
Finish - Steel painted.

CONSTRUCTION: Material may be steel, stainless steel, cast

iron or aluminum. Treads are supported in cantilever fashion by
the column, each consecutive tread being rotated at a
predetermined 'angle. The platform attaches to the column and
is fastened to the floor structure to hold the column secure. The
spiral railing is supported by balusters attached to the other ends
of the treads.
TREAD DESIGNS: Fabricators provide several standard types
and designs of treads and platforms. These include open riser,
closed riser and cantilever types, with surface of checkered
plate, abrasive plate, steel grating or plain surface to receive
wood, resilient flooring, carpet or other covering. Pan type treads
to receive concrete or terrazzo fill are also available.
STAIR HEIGHT: Spiral stairs are adaptable to any height, the
height being equal to the distance from finished floor to finished
floor.
HEADROOM: NAAMM recommends 78" minimum. However,
building codes generally dictate headroom requirements, some
codes requiring 80" minimum clearance. Minimum riser
dimensions given are based on this requirement .
CAUTION: Depth of landing must be considered to determine
the minimum headroom dimension.

SPIRAL STAIRS are used either indoors or

outdoors, conserve valuable floor or ground
space and provide the most vertical ascent of
any stair. They are of rugged self-supporting
construction,
graceful
in
design
and
architecturally attractive in appearance.

NOTES: Governing codes should be consulted by the architect to see that stairs conform to requirements.
Consult manufacturers' catalog for details, and specifications.

STAIR DIAMETER: Spiral stairs are available in various diameters from 36 to

8'0", normally in 6" increments. A 4'0" diameter is considered minimum for general
access purposes; a 5'0" diameter provides a comfortable general purpose stair.
Larger diameters are used chiefly for architectural effect. NOTE that the diameter
of the finished well opening should be at least 2" greater than the stair diameter,
to provide hand clearance.

HAND OF STAIRS: Left-hand

stairs - User ascends in clockwise
direction, with handrail at his left.
Right-hand stairs - user ascends in
counter clockwise direction, with
handrail at his right.

SPECIFICATIONS REQUIRED FOR PRICING AND MANUFACTURE:

1.Stair diameter and height from each finished floor to finished floor level.
2.Type of stair and tread surface or tread design.
3.Simple sketch showing all starting and landing positions, adjacent walls or partitions, if any, and size of well opening.
4. Type of metal.
5.Type of platform and well railing required.
6.Detail of any special design or requirement.

A stair is called a winder stair when the direction of a

straight flight of stairs is changed by substituting fixed
treads for a landing. The line of travel is close to the
rail and the turn is made at the narrow width of the
treads, breaking the walk pattern.

In a spiral stair the line of travel is at the outer or widest part of the tread. The walk pattern is also toward the spiral
rail. At no time is the line of travel near the center pole or the inside of the tread. the hand is always on the rail
whether ascending or descending.

DESCRIPTION
Steel Stairs 56 or 68 angle.
Available in carbon steel or stainless steel.
Construction All welded with bolt-on
handrails.
Finish Stainless steel, natural. Carbon
steel, primer or optional safety yellow paint,
also available with hot dipped galvanized
coating.
Aluminum Stairs 68 angle.
Construction All welded.
Finish Natural.

DESCRIPTION
Stringers Structural channels, aluminum or steel.
Treads Rectangular bar grating. Aluminum grating bolted
to aluminum stringer. Steel grating bolted or welded to steel
stringer. Corrugated or abrasive nosing for aluminum
grating. Checkered plate or abrasive nosing for steel.
Risers Open.
Railing Pipe. Posts welded to railing. Aluminum posts
bolted to aluminum stringer. Steel posts bolted or welded to
steel stringer.
Fasteners Stainless steel for aluminum. Steel for steel.
Finish Aluminum, mill finish or anodized. Steel galvanized
and/or painted.

SECTION 3
INSTALLATIONS
REPRESENTATIVE OF
CUSTOM DESIGNED STAIRS
Section 2 presents the more standardized type of metal stair construction. This section presents stairs which
were custom designed to achieve aesthetic effects as well as serve functional needs of the building. Photographs
and details shown in this section of the Manual are mostly of stairs made by NAAMM members.
As in the case of Section 2, the designer is advised that, should designs similar to any of those illustrated in this
section be considered for use, certain modifications may be necessary to conform to governing code
requirements.
NOTE: In each case the descriptions given apply only to the stair shown.
C0NTENTS
Straight Stair: Three Flights 3-2
Parallel, Glass Balusters 3-3
Parallel 3-4,3-6
Angled 3-7
Angled, Glass Balusters 3-8
Circular Stair: ................... 3-10, 3-11, 3-12, 3-14, 3-16
Curved Stair: Angled 3-17

DESCRIPTION
Stringers Steel I-beams.
Treads Steel pans, reinforced, filled with
concrete. Open risers.
Railing Steel pipe with brass tubing top rail
and handrail. Infill framed expanded aluminum,
attached to steel posts and rails.
Finish Painted steel. Natural brass.

DESCRIPTION
Stringers Steel channels covered with formed stainless
steel.
Treads and Risers Z profile sheet steel formed to provide
integral pan type tread and riser units. Supported on bent bar
shelf and back-up welded to stringers. Filled with concrete and
covered with carpeting.
Landing Stiffened sheet steel pans, reinforced concrete
filled, supported by structural channels.
Railing Tempered glass panels supported in aluminum
shoe moldings on resilient plastic setting blocks, two per
panel, located at quarter points. Shoe moldings fastened to top
of stringers with cap screws. Stainless steel circular cap
railing.
Finish All stainless steel #4 bright polish finish.

DESCRIPTION
Stringers Steel hollow rectangular shape.
Treads and Risers Integral pan tread and riser,
formed steel, concrete filled.
Platforms Steel pan, concrete filled.
Railing and Posts Steel pipe, welded
connections.
Finish Steel painted.

DESCRIPTION
Stringers Box construction, two structural steel
channels boxed by steel plate.
Treads Formed steel plate, concrete filled.
Landing Formed steel plate, reinforced, concrete
filled, supported by box stringers, bearing in masonry.
Railing Square steel bars welded to treads and
top channel, and connected to rectangular steel
tubing.
Finish Steel painted.

DESCRIPTION
Stringers - Steel tube.
Treads Formed steel plate, concrete filled; vinyl
surface.
Platforms - Formed steel plate, concrete filled; vinyl
surface. Steel tube supports, bearing on masonry or
supported by steel hanger rods.
Railing Balusters steel bars, welded to treads and
platforms; top channel capped by handrail.
Finish Steel painted.

DESCRIPTION
Top Rails, Base Rails and Posts Extruded aluminum, welded connections.
Infill Panels 1/4" tempered glass supported between top and base rails.
Stringers Steel box beam covered with sheet rock.
Stairs Poured-in-place concrete.
Aluminum Finish Paint.

DESCRIPTION
Stringer Welded steel plate.
Treads Formed steel plate. Tapered center beams
welded to tread plate and anchor plates. Anchor plates
bolted to stringer. Plywood fillers in ends of treads.
Oak end trim attached. Treads carpeted.
Railing Round steel bar balusters welded to treads
and attached to wood handrail at top.
Finish Steel painted.

DESCRIPTION
Stringers Steel plate.
Treads and Risers Steel sheet sub-treads and
risers supporting wood treads and risers. Covered
with carpeting.
Railing Malleable iron ornamental balusters
fastened to stringers through stringer cap. Steel
handrail mounted on steel channel.
Finish Metal painted. Plaster soffits and fascia.

DESCRIPTION
Stringers Steel plate welded to form box,
covered with brushed finish bronze.
Treads Formed steel pans filled with
concrete covered by marble.
Risers Formed steel covered by marble.
Fasteners A325 bolts.
Railing Polished bronze rod balusters.
Polished bronze tube handrails. Polished
cast bronze rail end cap.
Reveal Bronze sheet.

DESCRIPTION
Stringers Structural steel channels.
Treads and Risers Formed steel
sheet welded to stringer covered with
marble.
Railing Steel bar balusters. Bronze
tube handrails.
Wall Handrail Bronze cap on
sculpture painted A36 steel.
Baluster Sculpture painted A36
steel.

DESCRIPTION
Stringers Welded steel plate box stringers.
Treads Formed steel plate, field welded to angles on
stringers, concrete filled and covered with tile.
Railing Square steel bar balusters welded to
stringerers. Steel tubing handrail.
Finish Steel painted.

DESCRIPTION
Stringers Structural steel channel and plate welded
together after bending to form box section.
Treads and Risers Reinforced precast terrazo with
two setting plates per tread. Riser plates continuously
welded to stringers. Setting plates in tread field welded
to riser plates.
Railing Aluminum balusters attached to post anchors
cast in treads. Aluminum handrails.
Finish Steel painted. Aluminum anodized.

SECTION 4
CONSTRUCTION DETAILS
The drawings contained in this section illustrate the most commonly used and recommended details of metal stair
construction. Because of the unlimited design variations possible, particularly in the architectural class, this is
necessarily only a representative collection of such details.
The intent is to illustrate a variety of good construction practices, not a catalog of available designs. As some of
the items shown may not be available from all stair manufacturers, it is recommended that before finalizing the
specifications a NAAMM member company be consulted.
C0NTENTS
Stair Dimensions 4-2 and 4-3
Stringer Sections 4-4
Tread Sections 4-5
Tread and Riser Supports 4-6
Abrasive Nosings and Treads 4-7
Platform Construction 4-84-11
Platform Intermediate Supports 4-12
Stair Soffits 4-13
Newels, Railing Posts, Flanges, and Railings 4-134-17
Glass Railing Components 4-18 and 4-19
Handrail Sections 4-20 and 4-21
Wall Handrail Brackets 4-22
Wall Handrail Bracket FasteningsGeneral Information 4-23
Wall Handrail Terminals 4-24

REFER TO GOVERNING CODES TO ESTABLISH DIMENSIONS

Height of riser and tread run vary according to governing codes. A
tread of 10" and a rise of 7" to PA" are considered average. Stair
treads for more comfortable runs are often 101/2" to 11" with risers
less than 711. Treads and risers should be so proportioned that the
sum of two risers and one tread run is not less than 24" or more than
26".
In establishing stairwell dimensions, tread run is always face to
face of riser.

Minimum code requirements are usually measured from finished wall to finished
wall. When establishing rough stair well dimensions, allowance should be made
for thickness of any finish materials to be applied to the rough walls.

CONSTRUCTION NOTES:
Where masonry walls are finished with glazed brick, tile, marble or
other facing material, the stair should be erected before the finished
wall material is installed to permit a proper fit between it and the
all stringer Alternatively the wall stringer may be set out from the wall
to provide clearance, this construction requiring supporting brackets or
extension of wall stringers into the wall.
Steel plate stair stringers should be of sufficient width to receive the
end of tread and riser, and in thicknesses as determined by the load
and the design. Steel MC stringers are rolled in 10" and 12"' depth. For
average installation 10" channels are recommended. 12" channels are
used where required by the design and the load.
Box type stringers may be constructed with rectangular tube steel. For
load tables of steel stringer sections refer to Pages 5-11 and 5-12.
For details of metal stair soffits refer to Pages 4-12 and 4-13.
For sections of treads and risers, refer to pages 4-5 through 4-7.

CONSTRUCTION NOTES:
Sections shown on this page indicate the many different types of treads used for service type stairs, including pan type
sub-tread and riser construction.
Treads can be supported by direct bolting or welding to stringers, or bolting or welding to support members. The tread
width should always be greater than the tread run.
Refer to National Association of Architectural Metal Manufacturers' Metal Bar Grating Manual and to manufacturers'
current literature for more detailed information.
Refer to Page 4-7 for details of safety nosings.

CONSTRUCTION NOTES:
The tread and riser pan can be either welded or bolted to the supporting
ember. This is usually governed by the preference of the fabricator or the erector.
Treads made from grating or other pre-fabricated materials are usually furnished with end plates or angles standard with
the manufacturer. These can be either welded or bolted to the stringers.
The concealed direct welding of the pan tread to the stringer as shown in Figure 18 results in a clean soffit appearance.
This method is most efficiently used in "unit" or "pre-assembled" stairs where a complete stair flight is welded together in
the fabricator's shop and delivered to the site in one piece.

CONSTRUCTION NOTES:
With reference to Figures 21, 22, 23 and 24 extreme care should be used to be sure the fill is
fluid enough to flow completely around these anchors to insure a good bond of t he anchors,
but not so wet that shrinkage will occur.
Consult nosing manufacturers' current data for limitations of length, width, thickness and other
features such as colors, anchors, variations in design, etc.
The inside corner of cast nosings must be clean and square to fit a formed nosing properly.
Cast abrasive treads, Figures 25, 26 and 27 and also cast abrasive platforms are cast from
patterns that are standard with each manufacturer. Consult manufacturers' current literature
and engineering data for limitations of loading, length, width, thickness and other features.

Details for indicated sections are shown on this and the fol owing
two pages.
Platform construction methods shown are typical for many uses of
metal stairs. The details shown are often interchangeable, and
scan be modified in other ways to fit various conditions .
Supports for stair platforms are usually concealed in the walls
which surround the stairs, and can either be the walls themselves
when loadbearing, or may be struts to the floor below, or hangers
from the floor above.
Stair winders are usually built as part of the stair platform. A newel
post with sufficiently large base should be provided to receive the
ends of the treads and risers. Local laws or ordinances should be
checked for regulations covering this type of construction.
Reinforcing steel should be calculated for unusually large
platforms. For sizes indicated here, the concrete fills shown have
proven adequate as to allowable deflection and prevention of
cracking.

CONSTRUCTION NOTES: Gypsum Board or Plaster Soffit 11/4 " x 11/4 " x 1/8" steel angle clips welded to stringers
approximately 12" o.c. to support furring channels, gypsum
board or metal lath and plaster provided by others.

Center Railings are recommended for

wide stairs. They may be a single pipe or
tubing railing or they may be designed
with double rails and panels of interesting
design.
Note: A number of codes require that
railings have a leveI extension beyond
the nosings at the floors as indicated in
Fig. 78 by dashed lines. This applies to
both wall and center railings.

EXTRUDED ALUMINUM AND BRONZE HANDRAIL SECTIONS TYPICAL OF SEVERAL MANUFACTURERS

Most of these sections can be mounted on channels or flats, secured by screws from below. Some are designed for mounting on handrail
brackets. The use of channels instead of solid bars often simplifies the attachment of baluster and ornaments. The channels may be of the
same or a different metal.

On projects requiring the development of original designs, the cost of special dies is not excessive when spread over a sufficient quantity. For
moderate quantities, cost may be kept at a minimum by the use of available sections. Consult manufacturers' catalogs for exact contours,
sizes and availability of specific sections.
All sections have limitation, in forming curves without distortion. Solid sections should be selected when curving is required. Stock corner
bends are available for many handrail sections.
ROLLED STEEL HANDRAIL SECTIONS TYPICAL OF SEVERAL MANUFACTURERS
Most of these sections can be mounted on channels or flats, secured by screws or welding from below. Sometimes they are welded directly to
the baluster (see Fig. 94) or attached to handrail brackets (see Fig. 85). The use of channels often simplifies the attachment of balusters and
ornaments.

Extremely high tooling cost prohibits the use of special hot rolled steel sections even on large projects. The choice is limited to available stock
sizes. Consult manufacturers' catalogs for exact contours, sizes and availability.

GENERAL INFORMATION
Functional and decorative plastic handrail mouldings of polyvinyl chloride plastics
are available in a variety of sizes and profiles, several of which are illustrated
above. Consult suppliers current literature for variations in details and features.
Plastic handrail mouldings are not structural and require bar, tube, or channel
members to support vertical and horizontal loads.
Plastic handrail mouldings are produced in a range of colors from subdued to
bright, to suit either formal or informal design situations. The color is integral with
the plastic, which is highly resistant to wear, weathering, and corrosion.
The thermoplastic material becomes pliable when heated (not over 165F), at
which time it can be fitted over the support member and conforms to vertical,
horizontal or combined vertical and horizontal curves within certain limitations.
Lateral bends should have a minimum centerline radius of not less than 2 times
the width of the plastic section or 2 1/2 to 3 times the width of the support section,
whichever is greater. Mitered corners should be used if sharper turns are
required.
Combined vertical and horizontal turns can be formed by twisting the moulding.
The material can be joined by thermal welding, and end caps can be shaped
using a knife, file or abrasives.
The use of a cleaning -solution for removing grease and foreign material is reco
mended after which a solvent is used for polishing or removing abrasive
scratches. Normal cleaning requires only soap and water.

WALL HANDRAIL BRACKETS GENERAL INFORMATION

Wall rail brackets and handrail sections should be selected according to the strength and rigidity desired. In general, lighter sections require
closer bracket spacing. Hard usage, as in factories and schools, requires substantial sections, closer bracket spacing, sturdy brackets and
secure wall fastenings.
Fastenings as shown on this and the opposite page are typical, variations being dependent upon wall construction. Since new wall
construction methods are developed from time to time, current manufacturers' literature for handrail brackets and anchoring devices should be
consulted.
Bracket Spacing:
Spacing of brackets is recommended to be from three to six feet.
For Wood Frame Construction:
Brackets are usually fastened to wood construction by means of wood screws, with flat, round and oval heads. They may also be fastened by
lag bolts using one bolt per bracket. Wood backing should be suitable for uniform spacing.
For Solid Masonry Construction:
Brackets are usually fastened to masonry construction by through bolts or by expansion bolts of various types. It is preferable to use brackets
designed for one bolt, as bolts set too close will crack the masonry and become loose. They also may be fastened by wood screws or lag bolts
into lead anchors.
For Hollow Tile or Block Construction:
Brackets can be fastened to hollow tile construction by toggle bolts or through bolts. If through bolts are not practical, a proper anchorage can
be selected for each bracket at the job site when the anchorage hole is drilled.
For Lath and Plaster, and Dry Wall Construction:
Brackets are usually fastened to lath and plaster and wall board walls by screw anchors into wood or metal backing. Adequate back-up
support for anchoring handrail brackets must be in place before plaster or dry wall is installed.
For Walls Faced with Marble or Other Paneling:
Where wall facings are not sufficiently rigid for securing brackets, bolts should be anchored into the backing before the facing is placed, which
must be drilled for the bracket bolt.

SECTION 5
STRUCTURAL DESIGN
AND DATA
C0NTENTS
Introduction 5-2
ENGINEERING DATA
Mechanical Properties 5-3
Symbols and Formulas 5-4
Treads and Risers, Load Deflection Tables ... 5-5,5-11 and 5-12
Sheet Properties and Load Tables 5-5
Floor Plate and Tread Plate: Types 5-6
Load Deflection Table 5-7
Platform Constructions, Load-Deflection Tables 5-8 and 5-9
Stringers, Load-Deflection Table 5-10 and 5-11
Hanger Supports, Details and Load Tables 5-12
Strut Supports, Details and Load Tables 5-13
Channels, Section Properties 5-14
Properties of Railing Sections: Round Pipe 5-29
Square and Rectangular Tubing 5-29 thru 5-32
Channels, Extruded and Hot Rolled 5-32
Flats, Squares and Rounds 5-33
STRUCTURAL DESIGN EXAMPLES
Steel Stair Framing 5-15 thru 5-17
Connections 5-18 and 5-19
Aluminum Stair Framing 5-20
Ship's Ladder 5-22
Railings 5-23 thru 5-28

INTRODUCTION
In this section, examples are presented as guides in the structural design of stairs and railings. Several of these
examples illustrate the design of stair framing members; others illustrate the design of their connections. Typical
stair railing designs are provided also.
The first part of this section contains tables listing the load capacities, and deflections under loading, of principal
stair members and parts. Tables listing the structural properties of many of the pipe, tube, bar, and rod sections
commonly used in stair railing construction are found at the end of the section.
Although design tables may have been developed for the particular grade of material indicated, they may be used
for other grades and stress levels by multiplying tabular values by appropriate ratios in most cases.
NAAMM recommends that fixed metal stairs be designed and constructed to support a minimum live load of 100
pounds per square foot of projected plan area. Also, an individual tread should be able to support a concentrated
load of 300 pounds applied at its midspan with no other live load applied.
While limitations on allowable deflections may not be imposed, deflection under loading is an important
consideration in establishing a psychological sense of structural integrity.
The American Iron & Steel Institute and ASTM are discouraging the use of gage numbers to define sheet steel
thicknesses. The gage numbering system, based on an outdated system for specifying sheet steel, was
developed originally when rolling mills could not hold to close tolerances. With improved technology mills are
producing sheet steel for specific customer requirements to either minimum or nominal thickness. Current
industry practice is to order and supply sheet steel by decimal thicknesses, not gage numbers. Consequently, in
this 5th Edition of the Metal Stairs Manual, nominal sheet steel thicknesses have been shown in Tables, and gage
numbers have been shown in parentheses for convenience in making the transition.
Although Load and Resistance Factor Design (LRFD) is being used in addition to Allowable Stress Design (ASD)
by many engineers, the illustrative design examples in this manual follow the ASD procedure. However, Table 5.1
does not provide design stresses as in past editions. Instead, both yield and tensile stresses are given so that the
designer must apply either a safety factor if using ASD or a load factor if using LRFD.

LOAD AND DEFLECTION TABLES FOR TREADS AND RISERS The tables of engineering data and the sample calcula- stair stringers. (See
page 4-6) The industry unit for tread tions given in this section should be valuable aids to the length is 22 inches and the unit for half tread
length is designer of metal stairs. Uniform loads and deflections 12 inches. The spans used in the load and deflection for typical treads, risers
and subtreads are given on this tables are multiples of the unit tread length and multipage and on pages 5-7, 5-10 and 5-11. The formulas for
ples of the unit tread length plus half unit length. As a uniformly distributed loading on simply supported matter of convenience to the designer
the moment of inbeams are used to calculate the values given in the ertia and section modulus are given for each design tables. Simply
supported beams have unrestrained covered by the tables. This will facilitate the calculation ends. This means that the values are
conservative of loads and deflections for spans other than those because tread ends are restrained when attached to the shown.

FLOOR PLATES
Floor plates having raised platforms are available from several mills, each
offering their own style of surface projections and in a variety of widths,
thicknesses, and lengths. A maximum width of 96 in. and a maximum
thickness of 1 in. are available, but availability of matching widths,
thicknesses, and lengths should be checked with the producer. Floor plates
are generally not specified to chemical composition limits or mechanical
property requirements; a commercial grade of carbon steel is furnished.
However, when strength or corrosion resistance is a consideration, raised
pattern floor plates are procurable in any of the regular steel specifications.
As in the case of plain plates, the individual manufacturers should be
consulted for precise information. The nominal or ordered thickness is that of
the flat plate, exclusive of the height of raised pattern. The usual weights are
as follows:

Dimensions: Steel Floor Plate is produced in several designs

and in thicknesses of 16, 14 and 12 gage, 1/8", 3/16", 1/4119
5/16", 3/8", and 1/2", in widths to 72" and lengths to 30'-0".
Aluminum Tread Plate is produced in thicknesses of 0.10",
1/8", 3/16", and 1/2", in widths to 60" and lengths to 16'-0".
Thickness is measured through the body of the plate, not
including the raised portion.
Steel Floor Plate and Aluminum Tread Plate are used in stair
construction for treads and platforms.
Surface: Steel Figs. A to C, and Aluminum, Fig. E, have
regular mill finish.
Abrasive Plate, Fig. D, is produced in both steel and
aluminum with the abrasive material rolled into the surface.
Availability: Steel Floor Plate and Aluminum Tread Plate are usually available in warehouse stocks.
Floor Plate is the trade designation for steel. Tread Plate is the trade designation for aluminum. Other non-ferrous metals and stainless steel
may be rolled for special requirements when the quantities are sufficient for mill tonnage. Refer to manufacturers' data.

LOAD AND DEFLECTION TABLES - FLOOR AND TREAD PLATE

Tables 5.8-5.11 show allowable load (w) in pounds per square foot and
deflection (A) in inches. Weight of plate included.
Where stepped line is shown, loads above and to the right of this line
cause deflections exceeding 1/100 of the span.

LOAD TABLES FOR PLATFORM SUPPORTS (Pages 5-8 and 5-9)

These tables list the total allowable uniform load in kips sheet when counted as part of the section. for the sections shown. Total load
deflection is limited to equire spacing o s ruc ura sections can e e er1/360 of the span. Greater deflection may be permissible mined by
reference to Table 5.19. if soffit is not plastered. The calculations are based on the following assump- Design stresses used: tions: When
sheet is included as part of section, 20,000 psi* a) The spans are simply supported. When sheet is not included as part of section, b) Where
the sheet is counted in the section, the effec- 22,000 psi on non-compact sections (channels, tive width used is 12" when acting in tension (at
the angles, tees). (A36) bottom) and 16 times the thickness on each project- 24,000 psi on compact sections (I beams) (A36) ing side when
acting in compression (at the top). -------------------------------------------------------------------------------------------------c) The values of moment of inertia
(1), section modulus A570 Gr33 or A611 GrC. If Grades 36, 40 or D are used, (S) and computed deflection include the effect of the Tabular
values may be increased by 10%.

GENERAL NOTES
Allowable loads and deflections listed in
tables are based on fiber stresses at column
headings and apply to laterally braced
members. Stringers are considered to be
laterally braced by attached treads and risers.
W =, 2FS/3L
For stresses other than those listed, loads will
be proportionately smaller or larger.
Loads below heavy lines will cause deflect
ions exceeding 1/360 of span. Deflections for
loads less than those listed will be
proportionately less; see example at lower
right of facing page.
Weight of material is not included.

DESIGN OF RAILINGS
Due to the greater consciousness of safety requirements and the increasing provision in many codes of load limits on railings, architects and
engineers require detailed information concerning their loading criteria and structural design. They may be designed either to meet a particular
building code regulation or to meet the requirements of a specific installation.
In the structural design of a railing it is essential to know:
1. The structural loading criteria as established by governing regulations;
2. The mechanical properties and allowable design stresses of handrail metals;
3. The properties of the sections to be used;
4. Formulas for engineering design in terms of loading, stress and deflection relationships, and
5. Proper method of attachment and soundness of supporting structure.
Each of these considerations will be discussed in some detail in the following paragraphs.
Structural Loading Criteria
In its Voluntary Minimum Standards for Fixed Metal Stairs NAAMM recommends that railings and handrails be capable of withstanding a
minimum force of 200 pounds applied in any direction at any point on the top rail. This recommendation is based on a requirement originally
established by the Occupational Safety and Health Administration of the Department of Labor. Other codes, including the Life Safety Code of
NFPA have adopted this requirement. Some building codes may exceed this requirement. When such is the case the governing code will take
precedence.
Uniform load requirements for railings may also be found in some codes. These may call for resistance to a uniform horizontal and vertical
load of from 20 pounds to 50 pounds per lineal foot. In some instances the requirement is that the horizontal and vertical loads be acting
simultaneously. A few codes specify a vertical loading of 100 pounds per lineal foot.
For guard rails there is an NFPA Life Safety Code requirement that intermediate rails, balusters, and panel fillers be designed to resist a
uniform load of not less than 25 pounds per square foot of the gross area of the guard of which they are a part. This load, however, need not
be additive to the uniform horizontal load on the railing, mentioned in the preceding paragraph, in designing the main supporting members of
the guard.
Codes do not impose a limitation on the amount of deflection which may be allowed. However, deflection under loading is an important
consideration in establishing a psychological sense of structural integrity.
Mechanical Properties of Metals
Mechanical properties of the metals and alloys used in railings, as established by their producers, are listed on page 5-3.
Because the nonferrous metals are highly ductile, their yield strengths are defined by the maximum unit stress developed in producing a
specified permanent set. The magnitude of permanent set specified varies from 0.1% to 0.5% of the gage length of the tensile test specimen
and depends on the standard adopted for each metal by the appropriate authority. Due to the uncertainties in alloy composition, most
engineers prefer to use guaranteed minimum yield strengths rather than typical yield strengths.
A factor of safety must be applied, to take into account uncertainties in loading, methods of 'calculating stresses, and the variable properties of
materials. For structural metals in buildings, a factor of 1.65 applied to minimum yield strength or 1.95 applied to ultimate strength is generally
accepted as a minimum. In the following examples allowable stresses have been calculated by dividing minimum guaranteed yield strengths
by 1.65. For round tube and pipe the allowable stress is increased by a shape factor.
Properties of Sections
Properties of some of the sections commonly used for railing construction are contained in the tables on pages 5-29 through 5-33. Properties
of other sections can be found in the catalogs of their producers and in the AISC Manual of Steel Construction.
Formulas for Engineering Design
The determination of bending moments and stresses in the structural members of railings follows conventional engineering design procedures.
Stresses are calculated from bending moments and section properties using the flexure formula:
M X C M f = I = S (see footnote)
Railing posts act as columns in resisting vertical loading, and as vertical cantilever beams in resisting horizontal thrust applied to the tiop rail.
Bending moment produced by horizontal loading normally controls design, and stresses are calculated by the formula:
f = M_ = w11 2 x / x h for uniform loading S S
M = P X h f = S S for concentrated loading
See page 5-4 for explanation of symbols used.

These formulas apply to straight-run railings with uniform post spacing.

Although lateral bracing significantly reduces bending moment in posts, the
concern here is only with the basic, statically determinate condition. The
assumption that this condition exists will provide conservative design values
in all situations.
Bending stresses in welded pipe railing posts are determined in the same
way as for mechanically connected systems. When pipe or tubing is used,
the post strength may be increased by inserting a reinforcement in the tube
post.
In most railings the connections between posts and rails may be assumed
to be free to pivot. The distribution of loads over two or more spans
decreases the bending moment in rail members, and stresses for various
span conditions are calculated by varying the bending moment constant K,
as follows:
For uniform vertical or horizontal loading:
f W/12 x /2 K = 8 for one or two spans
S x K K = 9.5 for three or more spans
For concentrated loads applied at mid-span:
f P X K = 4 for one span
S x K K = 5 for two or more spans
NOTE: Values of K reflect the relative maximum bending moment developed under the different loading and span conditions
Joints between posts and horizontal members in welded railings approach complete rigidity. Joint rigidity causes bending moments to be
distributed among members and often results in structures which are statically indeterminate. Because the difficulty of accurately determining
stresses in structurally indeterminate conditions may not be justified in terms of useful design data, many designers prefer to simplify the
design process on the safe side by assuming pinned joint conditions even when joints are welded.
An important consideration in welded aluminum railings is the effect of welding heat on the structural properties of aluminum. For example,
extruded pipe of aluminum alloy 6063-T52 has an allowable design stress of 11,500 psi, but within 1 " of a weld this allowable stress must be
reduced to 8,000 psi. Since maximum bending moment in continuous horizontal members generally occurs at points of support, the reduced
design stress will often control design.
Quality of workmanship in welded joints is also a very important factor in determining the strength of railing installations. Careful preparation,
including accurate notching and fitting of pieces to be welded, helps achieve both structural soundness and satisfactory appearance. Special
care should be taken to provide sound welds where subsequent grinding will remove weld material. Thin welds can produce stress
concentrations which are subject to cracking.
Deflection Considerations
Despite an absence of deflection criteria for handrails, deflection behavior under load should be considered by the designer. Even though
installations meet strength requirements, excessive deflection under load can produce a feeling of structural inadequacy on the part of those
who are using the stairs and depending on the railing for their safety.
Lateral deflection of posts under horizontal, perpendicularly applied loads are calculated by the formulas:
w112 x / x h3
3 . E i orm oa on rai ing span
P x h3 for concentrated load at top of
3 x E x I post
Vertical deflection of horizontal railing under vertically applied loads are calculated by the formulas:
5 x w112 X /4 for uniform load
384 x E x I
P X /3 or concentrated load at center
48 x E x I of span
Load Distribution
The formula for concentrated post loading (page 5-23) applies to straight-run railings with uniform post spacing. For installations where the
railing is laterally braced by a change in direction of attachment to other structure, bending moment in posts may be significantly reduced.
Similarly, in a railing system where balusters or posts are mounted securely into the floor or stair slab, the load applied to the rail at a post is
distributed to other posts on either side of the post under stress, reducing the load applied to that post. This reduction is dependent on the
stiffness of the rail relative to the stiffness of the post and a load proportion factor which is found from the graph on page 5-25.

Round pipe is used for many architectural products, including stair railings, as well as for structural purposes.
Dimensions and Weights: Pipe is produced in a variety of sizes and "schedules," of which those more commonly used in stair work are listed
in the table above. Standard weight steel pipe is measured by I.P.S. (iron pipe size), which is the nominal inside diameter. When weight is not
specified for steel, brass and aluminum pipe, standard weight is assumed to be implied.
Stainless steel pipe is produced in the same four schedules or weights. For Schedule 5 pipe the nominal wall thickness is .065" for 1" to 2"
diameters and .083" for 2 1/2" to 4" diameters; for Schedule 10 pipe the nominal wall thickness is .109" for 1" to 2" diameters and .120" for 2
1/2" to 4" diameters. If wall thickness is not specified, Schedule 5 pipe is normally supplied.
Finishes: The usual paint coatings may be applied to steel pipe. Brass pipe usually is given a chemical or polished
finish, aluminum pipe may have a mill finish or be polished or anodized, and stainless steel pipe may be polished or buffed as required. For
general information on finishes the NAAMM Metal Finishes Manual should be consulted.
Round Tubing is also available in steel, stainless steel, aluminum, bronze and other metals. It differs from pipe in that it may have thinner or
thicker walls and is measured by a different system, stating the outside diameter in inches and the wall thickness in decimal inches. Size
designations may differ somewhat with the metal used.
Steel tubing has a mill finish similar to that of cold drawn steel, and the usual paint coatings may be applied. Finishes for tubing or other metals
are similar to those used on pipe made of these metals.
Availability: Both round pipe and round tubing, in the sizes commonly used in stair work, are usually stocked by warehouses. Manufacturers'
catalogs should be consulted for currently available sizes.

Square and Rectangular Tubing is available in the various metals as shown in the accompanying tables. Steel and stainless steel tubing is
usually formed from cold rolled sheet, while the nonferrous tubing is an extruded product. This tubing is used for stair railings and newels, as
well as for many other architectural products.
Steel tubing is also made in a structural grade, by a hot rolling process. This structural steel tubing is often used for newels in stair work, and
for structural members of all kinds in building construction.
Dimensions: Tubing is generally measured by the outside dimensions in inches and wall thickness in decimal inches, though the system of
measurement may vary somewhat with different metals. The sizes most commonly used in stair work are listed in the accompanying tables,
but many other sizes are also available.
Corners: Steel and stainless steel tubing has slightly rounded corners, the radius of which approximates the wall
thickness. Aluminum' and bronze tubing normally has square corners.
Finishes: The mechanically welded steel and stainless steel tubing has a clean bright surface which, in the case of steel may be painted, and
in the case of stainless steel is usually polished. The nonferrous extruded tubing also is usually given a polished or buffed finish, and
aluminum tubing is often anodized. For general information on finishes, the NAAMM Metal Finishes Manual should be consulted.
Structural steel tubing, being a hot rolled product, has a somewhat rougher surface, similar to that of mild steel, which may be scaly or
sometimes have a light surface rust. This type of tubing is normally painted.
Availability: Most of the sizes shown in the tables, as well as many other sizes, are commonly available in warehouse stocks. Manufacturers'
catalogs should be consulted for currently available sizes.

SECTION 6

RECOMMENDED
VOLUNTARY STANDARDS
AND GUIDE SPECIFICATIONS

RECOMMENDED VOLUNTARY MINIMUM STANDARDS

FOR FIXED METAL STAIRS
The recommendations in this section are based on the accumulated experience of many years by the
manufacturers of metal stairs. They may not, however, conform to the building codes which govern design
requirements for different areas of the country. The designer must, therefore, check governing code requirements
and make certain that his design meets these requirements.
1. SCOPE
This standard defines the various classes of fixed metal stairs and their functions; sets forth minimum
requirements for construction, proportions and dimensions of interior and exterior fixed metal stairs of all classes;
applies to spiral stairs but not to other types of curved stairs.
2. PURPOSE
The purpose of this standard is to establish the minimum requirements for the design and construction of safe
fixed metal stairs.
3. CLASSES OF FIXED METAL STAIRS AND THEIR FUNCTIONS
3.1 Industrial
Industrial metal stairs are purely functional in character and are generally the most economical. They are
designed for either interior or exterior use in or on industrial structures, or as fire escapes or emergency exitways,
primarily for use by employees. They do not include stairs which are an integral part of industrial equipment.
3.2 Service
Service metal stairs served chiefly functional purposes, are usually located in enclosed stairwells to provide a
secondary or emergency means of travel between different floors or levels, and in multi-storied buildings
commonly serve as fire stairs. They may serve either employees, tenants, or the public, and are generally used
where economy is a consideration.
3.3 Commercial
Commercial metal stairs are generally intended to serve the public. They may be located either in the open or in
enclosed stairwells in public, institutional or commercial buildings and are used where appearance and finish are
important considerations.
3.4 Architectural
Architectural metal stairs are of more elaborate design and often serve as an architectural feature. They may be
wholly custom designed or may represent a combination of standard parts and specially designed elements. They
may be located either in the open or in enclosed stairwells in public, institutional, commercial or monumental
buildings.

4. CONSTRUCTION
4.1 General Requirements, All Classes of Stairs
4.1.1 Fixed metal stairs shall be of fire resistive construction and shall be designed and constructed to carry a
minimum uniform live load of 100 pounds per square foot of projected plan area or an alternative minimum
concentrated load of 300 pounds applied at the center of any tread span.
4.1.2 Minimum Loads for Railings, Handrails and Infill Areas
4.1.2.1 Railings and handrails for structures shall be capable of withstanding a minimum concentrated load of 200
pounds applied vertically downward and horizontally at any point on the top rail. Vertical and horizontal loads shall
not be applied concurrently.
4.1.2.2 Railings and handrails for structures other than one- and two-family dwellings shall be capable of
withstanding a minimum uniform load of 50 pounds per foot applied vertically downward and horizontally at the
top rail. Vertical and horizontal loads shall not be applied concurrently.
4.1.2.3 Railings and handrails for one- and two-family dwellings shall have the same requirements as 4.1.2.2
except the minimum uniform load shall be 20 pounds per foot instead of 50 pounds per foot.
4.1.2.4 Concentrated and uniform loads shall not be applied concurrently.
4.1.2.5 Infill areas shall withstand a 50 pound horizontal load distributed over a one square foot area, round or
square, within the infill area. This load shall not be applied concurrently with other loads.
4.1.3 Continuous metal railings shall be provided at all open edges of every flight, platform and floor. Handrails
between flights of stairs shall be continuous around newel posts. Where handrails are not continuous at the top or
bottom of a flight they shall extend at least 12 inches beyond the top riser and at least 12 inches plus the depth of
one tread beyond the bottom riser. At the top the extended handrail shall be parallel to the walking surface. At the
bottom the extended handrail shall continue to slope for the depth of one tread with the remainder parallel to the
walking surface. Tread depth is measured horizontally between the vertical planes of the foremost projection of
adjacent treads and at a right angle to the tread's leading edge, which includes the nosing.
4.1.4 Stairs having an egress width of less than 44 inches shall have not less than one handrail for each flight.
Stairs having an egress width of 44 inches but less than 88 inches shall have a handrail on each side of every
flight, and those having an egress width of 88 inches or more shall have, in addition to handrails on each side, a
center handrail in each flight. For spiral stairs handrails are required on both sides when egress width exceeds 48
inches.
4.1.5 Handrails shall be constructed so as not to cause loss of hand grip and their ends shall be returned to walls
or terminated in newel posts or safety terminals.
4.1.6 Wherever required, stairs shall have a toe plate forming a curbing at all open edges of platforms and at all
open ends and open back edges of treads.
4.1.7 All joints shall be neatly fitted, sharp edges shall be broken, all welding on exposed travel surfaces shall be
smooth, and all mechanical connections in the travel area shall employ countersunk fasteners.
4.1.8 There shall be no projections, obstructions or rough surfaces that are hazardous to stair users in the area of
travel.
4.2 Additional Requirements for the Various Classes of Stairs
4.2.1 Industrial Class Stairs
Treads of less than 9 inches in width shall have open risers. With treads of greater width, risers may be either
open or solid.
Toe plates shall be provided in the manner prescribed in 4.1.6.

4.2.2 Service Class Stairs Interior service stairs shall have solid risers. Toe plates shall be provided in the manner
prescribed in 4.1.6.
4.2.3 Commercial Class Stairs Risers may be either open or solid. All conspicuous welds shall be smooth and
flush.
4.2.4 Architectural Class Stairs Risers may be either open or solid.
All joints shall be as inconspicuous as possible, whether welded or made with mechanical connections.
5. PROPORTIONS AND DIMENSIONS
5.1 General Requirements, All Classes of Stairs
5.1.1 Within any one flight, there shall be no variation exceeding 3/16" in the width of adjacent treads or in the
height of adjacent risers. The tolerance between the largest and smallest treads or the largest and smallest risers
shall not exceed 3/8".
5.1.2 Treads and risers shall be so proportioned that the sum of two risers and one tread run shall be not less
than 24 inches nor more than 26 inches. This does not apply to spiral stairs, the requirements for which are given
in 5.2.5.
5.1.3 The length and egress width of intermediate platforms shall be not less than the egress width of the stair in
which they occur.
5.1.4 No flight shall have a rise of more than 12 feet. Spiral stairs and alternating tread stairs are excluded from
this requirement.
5.1.5 Handrails shall be located so that the upper surfaces of the top rails are not more than 38 inches nor less
than 34 inches above the surfaces of the treads measured vertically from the forward edges of the treads or
nosings. The upper surfaces of guard rails shall not be less than 42 inches above any platform, floor or ramp.
They shall have a clearance of not less than 1112 inches from any other object.
5.1.6 Wall handrails shall be located so that their upper surfaces are not more than 38 inches nor less than 34
inches above the forward edges of treads, shall have a finger clearance of not less than 11/2 inches from the
wall, and shall project no more than 31/2 inches into the required minimum egress width. See 5.2.5 for spiral stair
requirements.
5.1.7 Headroom shall be not less than 6'8".
5.2 Additional Requirements for the Various Classes of Stairs
5.2.1 Industrial Class Stairs
Riser height shall be not less than 61/2 inches or more than 81/2 inches and the tread, exclusive of nosing, shall
be not less than 8 inches or more than 11 inches. Riser and tread proportions shall be within the limits prescribed
in 5.1.2.
All treads shall have a slip resistant nosing which projects not less than 112 inch or more than 1 inch beyond
base of riser.
5.2.2 Service Class Stairs
Riser height shall not be less than 61/2 inches or more than 73/4 inches and treads, exclusive of nosing, shall be
not less than 9 inches or more than 11 inches. Riser and tread proportions shall be within the limits prescribed in
5.1.2.
All treads shall have a nosing which projects not less than 1/2 inch or more than 1 inch.

5.2.3 Commercial Class Stairs

Riser height shall be not less than 51/2 inches or more than 71/2 inches and treads, exclusive of nosing, shall be
not less than 10 inches or more than 141/2 inches. Riser and tread proportions shall be within the limits
prescribed in 5.1.2. All treads shall have a nosing which projects 1 inch.
5.2.4 Architectural Class Stairs
Riser height shall be not less than 51/2 inches or more than 71/2 inches and treads, exclusive of nosing, shall be
not less than 10 inches or more than 141/2 inches. Riser and tread proportions shall be within the limits
prescribed in 5.1.2.
All treads shall have a nosing which projects 1 inch.
5.2.5 Spiral Stairs
The requirements for riser height, tread width and width of stairs (not radius of tread) shall be as follows:
Riser Height 91/2 " maximum.
Tread Run 71/2 " minimum measured at 12" from the narrow edge.
Stair Width 26" minimum.
Stair width defines the clear walking area between the outer edge of the supporting column and the inner edge of
the handrail.
Balusters shall be spaced not more than 6" apart.
5.2.6 Alternating Tread Stairs
Handrails Shall be installed on both sides of stairs.
Tread Width 81/2 " minimum.
Tread Length (perpendicular to line of travel) 7" minimum.
Projected Tread 5" minimum.
Rise to Next Surface 91/2 " maximum.
When used as means of egress in buildings for space not exceeding 250 square feet with no more than five
occupants the following dimensions apply:
Tread Width 101/2" minimum. Tread Length (perpendicular to line of travel) 7" minimum.
Projected Tread 81/2 " minimum.
Rise to Next Surface 8" maximum.
The initial tread shall begin at the same elevation as the platform, landing or floor surface.
5.2.7 Winders
Riser Height 7" maximum.
Tread Width 9" minimum measured at 12" from the narrow edge with minimum tread width not less than 6".
6. VERTICAL BARRIERS
A rail or barrier shall be provided at each side of every stair.

7. EGRESS WIDTH
Stairs used to provide a primary means of egress shall be in width units of 22 inches. Such width shall be
measured between vertical barriers. No fraction of width units shall be considered except that 12 or more inches
in addition to one or more width units shall be counted as a half unit. Normal egress width shall be 44 inches or
two width units. Not all metal stairs are required to meet the width requirements of egress standards.

FOREWORD
Guide specifications are intended to be used as the basis for developing job specifications and must be edited to
fit specific job requirements. Inapplicable provisions should be deleted, appropriate information should be
provided in the blank spaces and provisions applicable to the job should be added as necessary. Notes to
specifiers are given in italics directly following the paragraphs to which they apply. Dates given with ASTM and
other standards were current at the time this manual was published. Specifier should use latest dates when
preparing job specifications.
SECTION 05510 STEEL STAIRS
PART I GENERAL
1.01 SCOPE OF WORK
Fabricate and install metal stair assemblies in accordance with the requirements set forth in this section.
1.02 ADDITIONAL WORK INCLUDED IN THIS SECTION
The following items are often specified in sections other than 05510. If they are to be part of the metal stair
contractor's work they must be specified here.
A. Reinforcing for wall rail brackets at dry wall partitions.
B. Framing for standpipes at platforms.
C. Framing around roof leaders.
D. Field measuring or weld plates, sleeves and insert locations.
E. Bonderizing of galvanizing materials.
F. Wood or glass for rails.
G. Wire mesh and rebar for treads and platforms.
H. Field measuring of new stair wells and verifying floor height.
I. Self furring lath for stair pans.
J. Continuous seal welding of fascia cover plates at boxed stringers.
K. Anchors or inserts for terrazzo or precast concrete.
L. Prime painting of galvanized materials.
The following items are not to be included in the metal stair contractor's work:
Temporary shoring or bracing
Demolition and removal of existing work
Clean up of existing construction prior to installation of stairs
Cutting, grouting and patching of tread fillers
Cleaning out of stair wells
Temporary wood filler for steel tread pans
Concrete supports for steel
Cutting; preparation of pockets; setting of plates, inserts, carpenter hardware or any other built-ins
Concrete fill for pans and platforms
Temporary lights and electricity
Temporary safety rails
Protection after erection

Wood trim for face stringers Rubber treads or carpets

Slip-resistant oxide for concrete fill Field painting
Final cleaning and protection of aluminum, stainless steel, bronze and glass
Light gauge metal framing attached to stair
Exact match of existing stair when extension required
1.03 RELATED WORK SPECIFIED IN OTHER SECTIONS
A. Section 03300 Cast-in-place Concrete: ltem(s)
B. Section 034 Precast Concrete: ltem(s)
C. Section 04200 Unit Masonry: Item(s)
D. Section 044 Stone: ltem(s)
E. Section 05120 Structural Steel: ltem(s)
F. Section 05 Nosings: ltem(s)
G. Section 05521 Pipe and Tube Railings: Item(s)
H. Section 05720 Ornamental Railings: ltem(s)
I. Section 05999 Miscellaneous Metals: Item(s)
J. Section 06431 Wood Stairs and Railings: Item(s)
K. Section 078 Roof Hatches and Smoke Vents: Item(s)
L. Section 092 Plaster: Item(s)
M. Section 09400 Terrazzo: Item(s)
N. Section 09650 Resilient Flooring: Item(s)
0. Section 09680 Carpeting: Item(s)
P. Section 09900 Painting: Item(s)
Q. Section 106 Partitions: Item(s)
For small projects, or at the option of the specifier, this work may be incorporated with other narrow scope
sections.
Structural framing and enclosures: Refer to ACI standards for concrete construction and AISC standards for steel
construction. (Items A, B, C, D, E, I & L)
Stair & railing support: Bearing and anchorage points shall be structurally adequate to support the stairs and rails.
Inserts, anchors, connectors, backup support and pockets to be installed by others shall be verified to be in
accordance with architect approved drawings prior to the start of erection. (Items A, B, C, D, E, I)
Tread materials: Specify method of support and coordination of shop drawings for anchorage. (Items B, D, I, J, M,
N, & 0)
Railings: Specify method of attachment and coordination of shop drawings. (Items G, H, I, J, L & P)
1.04 STRUCTURAL REQUIREMENTS
The structural adequacy of the metal stair design is the responsibility of the designer.
A. Metal stair assembly shall carry a minimum uniform live load of _______pounds per square foot of projected
plan area.

B. Metal stair assembly shall carry a minimum concentrated load of _________ pounds applied at the center of
any tread span.
Governing code shall be checked for load requirements. NAAMM recommends a 100 pound per square foot
minimum uniform live load or alternatively a 300 pound minimum concentrated load, not applied concurrently.
C. Railing assembly shall withstand a minimum concentrated load of ________ pounds applied vertically
downward or horizontally in any direction, but not simultaneously, at any point on the top rail.
Codes may vary in method of application and magnitude of load. Governing code should be checked for specific
requirements. NAAMM recommends 200 pounds minimum concentrated load applied in any direction at any point
on the top rail.
D. Railing assembly shall withstand a minimum uniform load of ________ pounds per foot applied (horizontally)
(and) (vertically downward), but not simultaneously, on the top rail.
Some codes have requirements for uniform loading on the top rails. Loads may be applied horizontally or
vertically or in both directions, but not simultaneously. Governing code should be checked for specific
requirements. Uniform loads are not to be applied concurrently with concentrated loads.
1.05 QUALITY ASSURANCE
A. Fabricator Qualifications
If special or unusual capabilities are required they should be set forth here.
B. Installer Qualifications
State as required in 1. 05 A. Or state specific qualifications required.
C. Regulatory Requirements
Determine code regulations that govern this work. Specify requirements and drawings that are necessary to meet
governing codes.
1.06 REFERENCES
A. Aluminum Association (AA)
1. Aluminum Standards and Data
2. Designation System for Aluminum Finishes
B. American Concrete Institute (ACI)
1. Recommended Practice for Concrete Formwork, ACI 347
C. American Institute of Steel Construction (AISC)
1. Manual of Steel Construction
D. Iron and Steel Society (ISS)
1. Steel Products Manual
a. Sheet Steel
b. Stainless and Heat Resisting Steels
E. American National Standards Institute (ANSI)
1. ANSI Z97.1-1984 Safety Performance Specifications and Methods of Test for Safety Glazing Material used in
Buildings.
2. Ansi/NAAMM MBG 531-88 Metal Bar Grating Manual 4th Edition.

F. American Society for Testing and Materials (ASTM)

1. A 29-90a Specification for Steel Bars, Carbon and Alloy, Hot-Wrought and Cold-Finished, General
Requirements for.
2. A 36-90 Specification for Structural Steel.
3. A 47-84(1989) Specification for Ferritic Malleable Iron Castings.
4. A 48-83(1990) Specification for Gray Iron Castings.
5. A 53-90a Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated Welded and Seamless.
6. A 123-89 Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products.
7. A 167-90 Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip.
8. A 269-90a Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service.
9. A 312-89a Specification for Seamless and Welded Austenitic Stainless Steel Pipes.
10. A366-85 Specification for Steel Sheet, Carbon, Cold-Rolled, Commercial Quality.
11. A 500-90 Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and
Shapes.
12. A 501-89 Specification for Hot-Formed Welded and Seamless Carbon Steel Structural Tubing.
13. A 525-90 Specification for General Requirements for Steel Sheet, Zinc-Coated (Galvanized) by the Hot-Dip
Process.
14. A 526-90 Specification for Steel Sheet Zinc-Coated (Galvanized) by the Hot-Dip Process, Commercial
Quality.
15. A 569-85 Specification for Steel, Carbon (0.15 Maximum Percent), Hot-Rolled Sheet and Strip, Commercial
Quality.
16. A 570-90 Specification for Steel, Sheet and Strip, Carbon, Hot-Rolled, Structural Quality.
17. A 575-89 Specification for Steel Bars, Carbon, Merchant Quality, M-Grades.
18. A 611-90 Specification for Steel, Sheet, Carbon, Cold-Rolled, Structural Quality.
19. A 635-90a Specification for Steel, Sheet and Strip, Heavy Thickness Coils, Carbon, Hot-Rolled.
20. B 43-88 Specification for Seamless Red Brass Pipe, Standard Sizes.
21. B 62-86 Specification for Composition Bronze or Ounce Metal Castings.
22. B 209-90 Specification for Aluminum and Aluminum-Alloy Sheet and Plate.
23. B 210-90 Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes.
24. B 221-90 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wires, Shapes, and Tubes.
25. B 241-90 Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube.
26. B 455-89 Specification for Copper-Zinc-Lead Alloy (Leaded Brass) Extruded Shapes.
27. B 584-90 Specification for Copper Alloy Sand Castings for General Applications.
28. E 527- Practice for Numbering Metals and Alloys (UNS).
G. American Welding Society (AWS)
1. Specifications for Welding Rods and Bare Electrodes.
H. Copper Development Association (CDA)
1. Standards Handbook, Wrought Copper and Copper Alloy Mill Products. Part 2 Alloy Data.
2. Standards Handbook, Cast Copper and Copper Alloy Products, Part 7 Alloy Data.
3. Copper, Brass and Bronze Design Handbook for Architectural Applications.

I. General Services Administration (GSA), Federal Specifications (FS)

1. FS-TT-P-641G(1) Primer Coating; Zinc Dust Oxide (for Galvanized Surfaces).
2. FS-TT-P-645A Primer, Paint, Zinc Chromate, Alkyd Type.
J. National Association of Architectural Metal Manufacturers (NAAMM)
1. Metal Finishes Manual
K. Steel Structures Painting Council (SSPC)
1. SSPC-SP2 Specification for Hand Tool Cleaning.
2. SSPC-SP3 Specification for Power Tool Cleaning.
1.07 SUBMITTALS
A. Make submittals in accordance with Section 013________.
If project specifications include a section in Division 1 establishing the general administration and procedural
requirements for submittal of Shop Drawings, Samples and Certificates for the project, include A, above, and
modify following paragraphs to avoid duplication.
B. Shop Drawings
1. Show sections and plans of stairs, dimensions and assembly of components.
a. Stringers
b. Treads
c. Nosings
d. Risers
e. Headers
f. Newels
g. Platforms
h. Struts, columns and hangers
i. Railings
j. Handrails
k. Brackets
l. Reinforcements
m. Anchors
n. Welded and bolted connections
If compliance with AWS standards for welding is specified, inspection of welds by a Certified Welding Inspector
shall be included as a separate item.
2. Comply with NAAMM minimum standards for construction, proportions and dimensions of fixed metal stairs.
Indicate NAAMM stair classification
Stair # ________, #________, #________, _______________________class stair
Stair # ________, #________, #________, _______________________class stair
Architectural drawings should indicate a stair designation for each stair on the job. To specify the desired
construction, degree of finish, proportions and dimensions state the class of stair opposite each stair designation.
3. Show all field connections.

4. Provide setting diagrams for installation of anchors, location of pockets, weld plates for attachment of stairs and
rails to structure, and blocking for attachment of wall rail.
5. Specify adequate back-up support for anchoring handrail bracket.
6. Indicate all required field measurements.
7. Submit one reproduceable sepia for approval.
OR
7. Submit _____________ copies for approval.
C. Samples
1. Submit duplicate samples of railing showing style and finish. One approved sample will be returned to
contractor.
This is only specified if appearance sample is required. Applies to pipe, tubing and extrusions but normally does
not apply to carbon steel.
2. Submit sample(s) of _____________________________________________________________
_____________________________________________________________________________
List specific components for which samples are required.
D. Certificates
1. Furnish manufacturer's certification that materials meet specification requirements.
OR
1. Furnish ___________________ by an engineer registered in the state where the project is located showing
that safety requirements are met.
(certification) and/or (calculations)
This requirement should be included only if called for by contract documents.
E. Substitutions
1. Any changes in specified material must meet requirements of the General Conditions "or equal" clause. (See
#_____________)
Indicate Section & Paragraph of the General Conditions that sets out "or equal" requirements.
2. Change materials in stair #____________ from__________ to____________. Changes in architectural details
to fabricator's standard procedures will be allowed when appearance and strength are not affected.
State any alternatives that affect the work and/or bid price of this section, such as a change in material or a
change to contractor's standard details.
1.08 DELIVERY, STORAGE AND HANDLING
A. Conform to requirements of Section 016_________.
If project specifications include a section in Division 1 establishing the general requirements for Delivery. Storage
and Handling of materials and equipment for the project, include A, above, and modify following paragraphs to
avoid duplication.
B. Deliver materials to the job site in good condition and properly protected against damage to finished surfaces.

C. Storage On Site
1. Store material in a location and in a manner to avoid damage. Stacking shall be done in a way which will
prevent bending.
2. Store aluminum, bronze and stainless steel components and materials in clean, dry location, away from
uncured concrete and masonry. Cover with waterproof paper, tarpaulin or polyethylene sheeting in a manner that
will permit circulation of air inside the covering.
D. Keep handling on-site to a minimum. Exercise particular care to avoid damage to finishes of materials.
For carbon steel delivery and erection reference should be made to the AISC Code of Standard Practice,
Sections 6 and 7.
PART 2 PRODUCTS
2.01 MATERIALS AND FINISHES
A. Carbon Steel
See page 5-3 for properties of steel.
1. Structural Plate ASTM
Insert the desired ASTM specification number. ASTM A 36 Structural Steel is the most widely used steel for
structural plate.
2. Structural Shapes and Bars ASTM
Insert the desired ASTM specification number. ASTM A 36 Structural Steel is the most widely used steel for
structural shapes and bars.
3. Miscellaneous Bar Shapes
Insert desired A ISI designation or A S TM specification number ASTM A 29 Steel Bars. AISI 1015 and 1020
Steel Bars. ASTM A 575 Merchant Quality Steel Bars. AISI M1020 Merchant Quality Steel Bars.
4. Structural Pipe ASTM
Insert desired ASTM specification number ASTM A 53 Black and Hot-Dipped, Zinc-Coated Welded and Seamless
Steel Pipe. Structural grade, untested pipe is accepted for structural and architectural applications.
5. Structural Tubing: ASTM
(round), (square), or (rectangular). Insert desired ASTM specification number ASTM A 500 Cold Formed Welded
and Seamless Structural Tubing in Rounds and Shapes. ASTM A 501 Hot Formed Welded and Seamless
Structural Tubing. Hot formed steel tubing is produced in rounds and shapes.

6. Sheet and Strip: ASTM

Insert desired ASTM specification number.
ASTM A 569 Commercial Quality Hot-Rolled Sheet and Strip.
ASTM A 635 Hot-Rolled Sheet and Strip, Heavy Thickness Coil.
ASTM A 570 Structural Quality Hot-Rolled Sheet and Strip.
Commercial quality hot-rolled and strip are generally used in metal stair construction. However, where structural
considerations are of primary importance structural quality should be specified.
ASTM A 366 Commercial Quality, Cold-Rolled Sheet.
ASTM A 611 Structural Cold-Rolled Sheet.
Cold-Rolled sheet is usually specified only when it is necessary to meet particular architectural finish
requirements.
7. Castings: ASTM
Insert desired ASTM specification number
ASTM A 47 Malleable Iron Castings (Grade 32510). ASTM A 48 Gray Iron Castings (Class 30).
Class 30 means 30,000 psi tensile strength. Grade 32510 means 32,500 psi yield strength and tensile strength of
50,000 psi. Although malleable iron is stronger than gray and would be preferable for some applications, some
items are available only in gray iron.
8. Finishes:
Refer to NAAMM Metal Finishes Manual for information on all finishes.
a. Surface Preparation. Remove loose scale, rust, grease, oil, moisture or other foreign materials to properly
prepare the surface for subsequent coating application.
1) Remove mill scale, rust and dirt following SSPC-SP2 for hand cleaning and SSPC-SP3 for power tool cleaning.
b. Galvanizing:
1) Products fabricated from shapes, plates, bars and strips shall be galvanized in accordance with ASTM A 123.
2) Sheet products shall be galvanized in accordance with ASTM A 525 and ASTM A 526.
3) Minimum coating weight oz/sq ft.
Coating Class G60 (Minimum Check Limit TripleSpot Test 0.60 oz/sq ft. weight on both sides of the sheet
combined) or heavier, is recommended for the use where exposures require durable protection. Refer to Table 1
of ASTM 525 for coating weights and tolerances.
c. Paint: Minimum one coat of rust-inhibitive primer , FS
(standard shop primer) (manufacturer's name and number) (Federal Specification number).
FS-TT-P-641 Zinc Dust-zinc Oxide Primer Coating (For Galvanized Surfaces).
FS-TT-P-645 Alkyd Type, Zinc Chromate, Paint Primer Other Specification. Select primer for drying time and
compatibility with finish coat. Primer must be lead free.

d. Touch-up for Galvanized Surfaces: Use paint primer meeting FS-TT-P-645.

B. Stainless Steel: Type
Specify AISI type 302, 304 or 316. 304 is generally the preferred type although 302 may often be used
interchangeably with it. See page 5-3 of this manual for properties of type 304. Where severe corrosion
conditions may be encountered 316 should be specified.
1. Sheet, Strip, Plate, and Flat Bar: ASTM______________
Insert the desired ASTM specification number. ASTM A 167 Stainless and Heat Resisting Chromium-Nickel Steel
for Plate, Sheet and Strip.
2. Pipe and Tubing: ASTM_______________
Insert the desired ASTM specification number ASTM A 269 Seamless and Welded Austenitic Stainless Steel
Tubing for General Service. ASTM A 312 Seamless and Welded Austenitic Stainless Steel Pipe.
3. Finish: AlSl No.___________________
Insert desired AISI number. (Refer to NAAMM Metal Finishes Manual, Finishes for Stainless Steel AMP 503 for
available finishes)
AISI No. 2D, dull mill finish is usually specified. When a general purpose polished finish is desired AISI No. 4 may
be specified. Some unique proprietary finishes are also available. These must be specified by manufacturer and
trade name.
C. Aluminum:
See page 5-3 of this manual for properties of aluminum alloys and The Aluminum Association's Aluminum
Standards and Data for more information.
1. Extruded Bar and Shapes: Alloy _________meeting ASTM B 221.
Insert desired Aluminum Association Alloy Designation 606176 or T62, 6063- T5 or T52, 6063-76.
2. Extruded Structural Shapes: Alloy 6061-T6 meeting ASTM B 221.
3. Extruded Tube and Pipe: Alloy __________meeting ASTM B 241.
Insert desired Aluminum Association Alloy Designation 6061-T6 or T62, 6063-T5, 6063-T6 or T62.
4. Drawn Tube and Pipe: Alloy __________meeting ASTM B 210.
Insert desired Aluminum Association Alloy Designation 6061-T6 or T62, 6063-T6 or T62, 6063-T832.
5. Tread Plate:
a. For platforms: Alloy 606176 meeting ASTM B 209.
Alloy 6061-T62 may be specified as an alternate.
b. For treads: Alloy 6061-T4 meeting ASTM B 209.

6. Finish:________________________
Specify The Aluminum Association Designation for mechanical, chemical, and anodic finishes. Architectural Class
I anodic finish is generally recommended. Where color anodizing is specified, allowable variation is limited
according to the cob or range of samples furnished by the finisher For applied organic coatings specify the type fo
coating and color required. (Refer to NAAMM Metal Finishes Manual Finishes for Aluminum AMP 501 for data on
anodic and organic finishes).
D. Copper Alloys:
See page 5-3 for properties of these alloys. Alloy designations for copper alloys are those of ASTM E 527
1. Copper Alloy No. C38500 (Architectural Bronze) 'Meeting ASTM B 455 for shapes.
Architectural Bronze Alloy C38500 is extruded in the form of bars, standard shapes and special shapes such as
handrail mouldings, square and rectangular tubing.
2. Copper Alloy No. C23000 (Red Brass, 85%) meeting ASTM B 43 for pipe.
Seamless brass pipe is usually supplied in Alloy C23000 which alloy provides a fair color match with Architectural
Bronze Alloy C38500.
3. Copper Alloy No. C28000 (Muntz Metal, 60%) for sheet.
Panels, sheets and trim are usually supplied in Alloy C28000. This alloy provides a fair color match with
Architectural Bronze Alloy C38500.
4. Copper Alloy No. C83600 meeting ASTM B 62 and B 584 for sand castings.
5. Finish: ________________________
(M32-Medium Satin) (M42-Fine Matte). These are the two mechanical finishes most commonly specified for
architectural bronze. Other mechanical finishes plus chemical and organic finishes are available. (Refer to
NAAMM Metal Finishes Manual Finishes for Copper Alloys AMP 502)
a. Apply a protective organic coating of clear lacquer approved by the Copper Development Association.
This paragraph should be included where protection of surface finish is believed necessary A general list of clear
organic coatings approved by the Copper Development Association is published in CDA's Copper, Brass and
Bronze Design Handbook for Architectural Applications.
E. Glass:Type , ________________________Thickness, ________________________Shall conform
to the safety requirements of ANSI Z97.1.
Accessories: _______________________________________________________________________
__________________________________________________________________________________
Insert glass type and thickness. List glazing accessories.
F. Welding Rods and Bare Electrodes. Select in accordance with American Welding Society specifications for the
metal alloys to be welded.

G. Fasteners: Match or be compatible with the metals being fastened.

2.02 FABRICATION
A. Components
1. Stringers:____________________________________________________________________
2. Headers: ____________________________________________________________________
3. Treads: ______________________________________________________________________
4. Nosings: _____________________________________________________________________
5. Risers: ______________________________________________________________________
6. Platforms: ____________________________________________________________________
7. Struts: _______________________________________________________________________
8. Columns: ____________________________________________________________________
9. Soffits: _______________________________________________________________________
10. Railings: ____________________________________________________________________
11. Handrails: ___________________________________________________________________
12. Newels: _____________________________________________________________________
13. Other Items: __________________________________________________________________
Where metal bar grating treads and platforms are to be used, they should be fabricated in accordance with the
requirements of ANSI/NAAMM MBG 531 Standard for Metal Bar Gratings.
It may not be necessary to specify material and finish requirements for all these components when a
manufacturer's standard stair is being specified. This information is needed where there are special requirements
and when custom designed stairs are called for.
Select materials and finishes to meet project requirements and indicate next to the component the appropriate
references to paragragh 2.01 Materials and Finishes. For example: Railings: Aluminum extruded shapes as
specified in 2.01.C.1 with finish as specified in 2.01.C.6.
This component list is supplied as a guide. The specifier may wish to add or subtract from the list for his particular
project. Where appropriate for a project components may be simply identified by a manufacturer's standard part
number.
B. Fabricate in compliance with shop drawings and commence fabrication only after these drawings have been
approved.
C. Remove all sharp or rough areas on exposed travel surfaces.
D. Provide protection against galvanic action between dissimilar metals.
PART 3 - EXECUTION
3.01 INSTALLATION
A. Field check and verify that structural framing, enclosures, weld plates, blocking, size and location of pockets
are as called for in approved shop drawings.
Report discrepancies to Architect and Contractor for corrective action by responsible parties.

B. Do not proceed with installation until stairwell is cleared.

C. Load, unload and handle material in a manner that will not strain, bend, deform or otherwise damage it.
D. Erect stairs square, plumb, straight, true to line and level, with neatly fitted joints and intersections. Installation
shall be secure and rigid.
E. Field welds in the area of travel shall be smooth.
F. Protect material from damage both before and during installation.
3.02 TOUCH-UP AND CLEAN-UP
A. Repair abraded galvanized finish by application of one coat of paint primer meeting FS-TT-P-645.
B. Touch-up field welds by application of one coat of primer as specified in 2.01.A.8.c.
C. Remove debris, containers and excess material resulting from work specified herein.

SECTION 7
GLOSSARY OF TERMS
Definitions of terms used in this Manual and other terms in common usage in the metal stair industry

GLOSSARY
ANGLED STAIR

CARRIER BAR

A stair in which successive flights are at an angle of other than

1800 to each other (often 900) with an intermediate platform
between them.
One of a series of closely spaced upright members which sup
port the handrail in a railing.
A railing which is composed of balusters capped by a handrail,
often serving as an architectural feature.
See Pitch.
A tread with one or both ends having a semi-circular shape in
plan; usually the first tread at the bottom of a flight.
A fitting used to close the end of a pipe or tubular rail or post,
or the top end of a tubular newel.
An angle connected to the inside face of a stringer to form a
supporting ledge for the end of a tread or riser.
A flat bar used in the same way as a carrier angle.

CHECKERED PLATE

See Floor Plate.

CIRCULAR STAIR

A stair which, in plan view, has an open circular form, with a

single center of curvature.
A flat metal bar connected in the field to the top and/or bottom
surface or edge of a wall stringer to close gaps between the
stringer and the wall.
A stair which, in plan view, has two or more centers of cur
vature, being oval, elliptical or some other compound curved
form.
A fitting used to close the bottom end of a tubular newel.
That curved portion of a handrail which forms a transition, in a
vertical plane, between a horizontal and an inclined section of
a handrail.
The exposed facing of the outer edge of a platform or floor;
usually similar in detail to the face stringer.
A cementitious material such as concrete or terrazzo, which is
placed over a metal substructure to provide the wearing sur
face of a tread or platform.
A permanently stationary series of three or more steps in one
or more flights, providing pedestrian access between different
floors or levels.
An uninterrupted series of steps.
See Header, Flight.
The vertical distance between the floor or platforms con
nected by a flight.
The horizontal distance between the faces of the first and last
risersinaflight.

BALUSTER
BALUSTRADE
BEVEL
BULLNOSE STEP
CAP
CARRIER ANGLE

CLOSURE BAR

CURVED STAIR

DROP
EASEMENT

FASCIA
FILL

FIXED METAL STAIR

FLIGHT
FLIGHT HEADER
FLIGHT RISE
FLIGHT RUN

FLOOR PLATE

GRAB RAIL (GRAB BAR)

GUARD-RAIL SYSTEM

GUSSET
HAND OF SPIRAL STAIR

HANDRAIL

HANDRAIL BRACKET

HANGER

HEADER, FLIGHT
HEADER, PLATFORM
HEADROOM

I.P.S.
KICK PLATE

LAMB'S TONGUE
LANDING
LATERAL SCROLL

A steel plate having a raised pattern to provide a non-slip

wearing surface; referred to as "tread plate" when made of
aluminum.
A short length of rail located for safety and convenience.
A railing system usually located for protection of building oc
cupants at or near the outer edge of a stair flight, ramp, land
ing, platform, balcony or accessible roof; at perimeter of any
opening or accessible surface, such as an opening for stair
way; or at a location where operating condition requires limita
tion of access to designated area, to guard against accidental
fall or injury. See Railing System.
A plate used to construct or reinforce an angular joint between
two or more members.
A term used to designate the direction of turn of a spiral stair.
Right-hand refers to a stair on which the user turns counter
clock-wise as he ascends.
Left-hand refers to a stair on which the user turns clockwise as
he ascends.
The member which is normally grasped by the hand for sup
port. This member may be part of the railing system or may be
mounted on the wall or other building element. It is often, but
not necessarily, the top member of the railing system. When
part of the stair-rail system it parallels the pitch of the stair
flight. See Wall Handrail.
A device attached to a wall or other surface to support a hand
rail.
A left-hand handrail bracket is one which is located on the
user's left as he ascends the stairs.
A right-hand handrail bracket is one which is located on the
user's right as he ascends the stairs.
A load-carrying tension member used to support a stair fram
ing member by suspension from the floor construction or other
support above.
A horizontal structural member at a floor or platform level, sup
porting the end(s) of one or more stringers.
A horizontal member supporting platform construction but
carrying no stringers.
The minimum vertical distance from the top surface of a tread
or platform to the ceiling, soffit or other overhead obstruction,
measured at the outer edge of the tread or platform.
Iron Pipe Size; a nominal inside diameter dimension of pipe.
A vertical plate forming a lip or low curb at the open edge of
platform or floor or at the back edge or open end of a tread on
an open riser stair.
An ornamental curved and tapered fitting terminating a hand
rail.
See Platform.
A fitting which curves in a horizontal plane, used to terminate
a handrail.

NEWEL
NOSING

PAN BRACKET
PAN TREAD
PARALLEL STAIR
PITCH
PITCH BLOCK
PITCH DIMENSION
PLATFORM

PLATFORM HEADER
PRE-ASSEMBLED STAIR
PRE-ERECTED STAIR

RAIL
RAILING SYSTEM

RAKE
RAKE DIMENSION
RISE
RISER

RISER, OPEN
RISER HEIGHT
RUN
SAFETY NOSING
SAFETY TREAD

A post member supporting the end of a railing or serving as a

common support for two railings.
That part of a tread or platform which projects as a square,
rounded or rounded and molded edge beyond the vertical face
of the riser below it.
See Carrier Angle or Carrier Bar.
See Tread, Pan Type.
A stair consisting of flights which parallel each other and are
separated by one or more intermediate platforms.
The angle of slope of a flight, measured either in degrees or by
the ratio of rise to run.
See Carrier Angle or Carrier Bar.
The distance between the bases of the top and bottom risers
in a flight, measured parallel to the pitch.
A horizontal surface having a dimension parallel to the string
er greater than a tread width, occurring in a stair at the end of a
flight or between flights, either at a floor level or between
floors. In the latter case it is sometimes referred to as an in
termediate platform or a landing.
See Header, Platform.
A stair whose components are assembled in the plant to make
up units of varying sizes and degrees of complexity.
A stair unit for multi-storied buildings designed to be self sup
porting. Such units can be stacked one upon the other and
field connected to form stair towers.
See Handrail.
A framework of vertical, horizontal or inclined members or
panels, or some combination of these, supporting a handrail
and located at the edge of a flight, platform or floor as a safety
barrier.
See Pitch.
See Pitch Dimension.
See Flight Rise.
The vertical or inclined face of a step, extending from the back
edge of one tread to the outer edge of the tread or lower edge
of the nosing next above it.
A term used to describe a stair having open spaces rather than
risers between treads.
The vertical distance between the top surfaces of two succes
sive treads.
See Flight Run and Tread Run.
A nosing having a slip resistant surface flush with the tread
surface.
A tread which has a slip resistant top surface.

SANITARY COVE

SCISSOR STAIR

SHIP'S LADDER

SIDE MOUNT

SOFFIT
SPIRAL STAIR
LIMITED ACCESS SPIRAL
STAIR
PRIMARY ACCESS
SPIRAL STAIR
STAIR
STAIR-RAIL SYSTEM
STAIRWAY
STAIRWELL
STEP
STEP RISE
STORY HEIGHT
STRAIGHT RUN STAIR

STRING
STRINGER

STRINGER, BOXED
STRINGER, CENTER
STRINGER, CLOSED
STRINGER, FACE

A small projection formed in the face of a metal riser along its

full length to provide an angled or curved transition between
the tread surface and the riser face to facilitate cleaning.
A straight stair which in plan view has two parallel flights be
tween floors but in which the stairs are at a 180 ang le to each
other.
A ship's ladder is named for its use as a stairway access be
tween decks of a ship. These ladders ascend at steep angles
of not less than 50 nor more than 77 with the deck, and cover
the angularity of ascent between that of conventional stairs
and straight ladders. They are not used for public stairways in
buildings.
A method of railing support in which the posts are anchored to
a vertical surface such as a fascia or stringer face. Also refer
red to as fascia bracket or fascia flange.
The under side of a stair, whether exposed construction or an
applied finish material.
A stair with a closed circular form, uniform sector shaped
treads and a supporting center column.
A spiral stair serving an occupant load of 10 or less and from
an area of 600 square feet or less.
A spiral stair serving an occupant load of 50 or less.
A flight or series of connected flights extending between two
or more floors within a given floor area or stairwell.
A railing system located along open side of stair or platform.
See Stair.
The vertical shaft space in a building occupied by a stair; also,
the open well space between a series of flights.
The combination of a riser and the tread immediately above it.
See Riser Height.
The vertical distance, in a building, between one finished floor
and the next.
A stair extending in a straight line between one floor and the
next, and consisting of one flight or a series of flights with one
or more intermediate platforms.
See Stringer, the preferred term.
An inclined structural member supporting a flight, or a struc
tural member having an inclined section with a horizontal sec
tion at one or both ends, supporting a flight and one or two
platforms.
A stringer having a hollow square or rectangular cross section.
A stringer located under a flight at its mid-width and support
ing the treads, or treads and risers, by cantilever action.
See Stringer, Boxed.
A stringer which supports, on one side, the ends of treads and
risers, and is exposed on the other side.

STRINGER, OPEN
STRINGER, PLATE
STRINGER, PLATFORM
STRINGER, TUBE
STRINGER, WALL
STRUT

SUB-PLATFORM
SUB-TREAD
TOE BOARD
TOE PLATE
TRANSFER RAIL
TRAVEL AREA
TREAD
TREAD ANGLE
TREAD BAR
TREAD, GRATING TYPE
TREAD, PAN TYPE
TREAD, PLATE TYPE
TREAD BRACKET
TREAD LENGTH
TREAD PLATE
TREAD RUN

TREAD WIDTH
VERTICAL BARRIER
VOLUTE
WALL CLIP OR FLANGE
WALL HANDRAIL

WINDER

A channel used as a stringer.

A flat plate used as a stringer.
A stringer, or that part of a stringer, which is used to support a
platform.
A stringer made from a metal tube section.
A stringer placed alongside a wall and usually carrying no rail
ing.
A structural member which resists axial compression loads.
Generally used to support a stair framing member by column
action.
The metal subfloor over which a fill is placed to provide a plat
form.
See Tread, Pan Type.
See Kick Plate.
See Kick Plate.
See Grab Rail.
That area with which a stair user might normally make physical
contact.
The horizontal member of a step.
See Carrier Angle.
See Carrier Bar.
A tread fabricated from metal grating.
A section formed from metal sheet to receive a fill and provide,
when filled, either a tread or a combination of plates.
A tread, or combination tread and riser, fabricated from metal
plate, floor plate, tread plate or a combination of plates.
See Carrier Angle or Carrier Bar.
The dimension of a tread measured perpendicular to the nor
mal line of travel on a stair.
A product similar to floor plate, but made of aluminum.
The horizontal distance between two consecutive risers, or, on
an open riser stair, the horizontal distance between nosings or
the outer edges of successive treads, all measured perpen
dicular to the front edges of the nosings or treads.
The tread run plus the projection of the nosing, if any.
A wall or railing adjacent or attached to the edge of a flight,
platform or floor, to prevent persons from falling.
A spiral or scroll-shaped fitting used to terminate a handrail.
A bracket used for anchoring.
A handrail attached to a wall adjacent to a stair and paralleling
the pitch of the flight; also used along walkways, ramps, and
corridors. Also referred to as a "wall rail."
A tread having less width at one end than at the other.