International

OPEN

Journal

ACCESS

Of Modern Engineering Research (IJMER)

BER Estimation for Laser Based Underwater Communication

Preeti Kumari1, Anjesh Kumar2
1

(Amity University, Gurgaon)

(Scientist, DRDO, New Delhi)

Abstract: Apart from land and air, sea has also become very important from defense strategic point of
view and is required to be integrated with network centric communication. In future it may play a very
important role in network centric warfare. Free space laser communications provide wide bandwidth
and high security capabilities to unmanned aircraft systems in order to successfully accomplish
intelligence, surveillance, target acquisition, and reconnaissance missions[l] Laser based
communication is emerging as a most promising solution for underwater communication. Most of laser
cannot penetrate through the sea due to be absorbed by the sea, but the blue-green laser (the
wavelength is about 470 ~ 570nm) has the minimum energy fading in the sea, whose fading rate is
about 0.155~0.5dB/m, this feature of blue-green laser in the sea is said the window effect[2]. Longrange links use directed laser beams to transmit data, and can be used for building-to-building, groundto-aircraft, or ground-to-satellite communication [3]. Laser communication throws quite different
challenges in water in respect to air. Laser attenuation in water is key bottleneck for underwater
communication as attenuation in water is roughly 1000 times as in air. This exponential variation plays
a very important role in determining the type of laser (CW or Q switched laser) and place a restriction
on the use of CW laser for longer distance because of impractical sizes. Turbulences and variation in
salt concentration in different part of a sea and in different seas imposes a dynamic challenge for
underwater laser communication. Issues at sea-air interface for aerial platform to underwater
communication also plays crucial role for establishing an uninterrupted communication link. All these
issues throttle the effective baud rate of transmission.

I. Introduction
Transmission of data at lower bit error rate (BER) is foremost characteristic of a communication system. It is a
very important parameter to be considered while modeling a communication system and specially
communication channel as sources of error at transmitting and receiving end can be modeled and optimized
more deterministically. ON-OFF Key (OOK) is the most common and simple (Implementation point of view)
modulation technique for CW laser beam. It is perfect solution for laser communication in air. In water, laser
attenuation is roughly 1000 times with respect to air so power requirement for underwater communication is
huge and vary exponentially . Size of CW laser imposes a practical constraint for higher power. Q switched
pulse laser is a ideal solution for high peak power requirement but imposes a constraint on modulation
technique.. Other possible modulation technique pulse width modulation (PWM) varies the energy of the Q
switched pulses and hence the overall communication path length degrades. In this paper we have calculated the
bit error rates for different sources of error in the water channel for both OOK and PPM.
BER calculation: Attenuation of laser beam in water degrades its intensity drastically and it degrades signal
amplitude at the detector output. Decision device will occasionally make error and consider symbol 1 as symbol
0. To determine the average probability of error, we first consider the two possible kind of error separately.
Assume that symbol 0 was transmitted, corresponding to a level of 0 volts. The output signal y(t) then consists
of noise alone, as shown by
Y(t) = n(t),
symbol 0 was sent
When symbol 0 is transmitted, the random variable yk is Gaussian-distributed with zero mean and variance 2
where yk denote the sample value obtained by observing the sample function y(t) at time t=t k and Yk denote the
corresponding random variable Hence, the conditional probability density function of y k given that symbol 0
was transmitted, equals

| IJMER | ISSN: 22496645 |

www.ijmer.com

| Vol. 4 | Iss. 12 | Dec. 2014 | 62 |

BER Estimation for Laser Based Under Water Communication

Let

denote the conditional probability of error, given that symbol 0 was transmitted. This probability is

defined by the area under the

curve, from A/2 to

, which can be expressed as:

The conditional probability density function of yk given that symbol 1 was transmitted, can be expressed as

Let

denote the conditional probability of error, given that symbol 1 was transmitted. This probability is

defined by the area under the

curve, from -

to A/2. Assuming equally probable symbols and

setting threshold midway between 0 and A, implies

=
.To determine the average probability of error in
the receiver, we note that the two possible kinds of error considered above are mutually exclusive events in that
if the receiver, at a particular sampling instant, chooses symbol I, then symbol 0 is excluded from appearing, and
vice versa. Furthermore,
and
are conditional probabilities with
assuming that a 0 was transmitted
and

assuming that a 1 was transmitted. Thus, assuming that the a priori probability of transmitting a 0 is

and the a priori probability of transmitting a 1 is

receiver is given by
Since

and we have assumed that

, we find that the average probability of error

in the

, we obtain

Which is given as:

Where is the signal to noise ratio.

The above calculation is for the case of on-off keying. Now we analyze the probability of error for a Pulse
Position Modulation (PPM) system. The PPM generally is applied to higher data rate in the underwater laser
communication. The PPM adopts optical pulse as the carrier which is controlled by the modulated signal. The
pulse position is varied with the modulated signal, and the message is transmitted via this position variation. The
efficiency of Pulse position modulation is higher than others modulations, especially in the underwater laser
communication system and it are most optimized. k-PPM decreases the average power requirement at the cost of
large bandwidth[4]. In terms of power efficiency if the k is greater than 2, PPM modulation exhibits a higher
efficiency than OOK does. An increase in k causes an increase in the bandwidth requirement. The average
number of bit errors per k-bit symbol is:

Where Pb is the average number of bit errors per k bit symbol and Pm is the bit error rate for a PPM system.

II. Lab setup for BER analysis

Transmitter: 200mW frequency double ND-YAG green laser operating at 532nm
Water channel: Water tank of path length 10 m
Data transfer rate: 10 Kbps
Detector: Silicon PIN photodiode
Mode: Duplex(full/half)/Chat mode
File type: Text file and Binary file
To estimate the BER, four sources of error are considered in the above setup as follow:
1.
Effect of channel attenuation on BER
2.
Effect of channel turbulence on BER
3.
Effect of ambient noise on BER
4.
Effect of laser ON-OFF stabilization rate on BER
| IJMER | ISSN: 22496645 |

www.ijmer.com

| Vol. 4 | Iss. 12 | Dec. 2014 | 63 |

BER Estimation for Laser Based Under Water Communication

1. Effect of channel attenuation on BER: Channel attenuation plays very crucial role in determining the BER
of a laser based communication system. Attenuation of laser beam propagation varies exponentially. Keeping
other factors constant (K), Attenuation () is the only variable. Laser propagation equation can be expressed as
Pr =Pt.e x
Where Pr is received power, Pt is transmitted power and x is the path length. Attenuation is most important
factor for deciding the power requirement of a communication channel. Attenuation factor of water is 1000
times of the air implies huge laser power requirement for underwater communication. Unit of attenuation
constant of beam of light is m-1 and used for finding laser attenuation underwater. It is not dependent on
wavelength and is approximately equal to 0.02 m-1 in clear water [5]. To analyze the effect of in the above
setup, attenuation of water is varied by adding NaCl in various concentrations and keeping other sources of
errors inactive. Transmitted laser power is kept constant and intensity modulated by a bit pattern generator.
Received power and bit pattern generated at the detector are compared with transmitted laser beam to analyze
the attenuation factor and BER. Results are present in the table below:
Types of water
RO water
Tap water
Salt water1
Salt water2

OOK
Av. BER(per 1Mb)
<1
< 1.5
< 1.5-2.0
< 2.5

PPM
<0.5
<0.75
<1
<1.5

2. Effect of intrachannel turbulence on BER: Sea waves may contribute to BER. Disturbance at sea surface
plays very crucial role in aerial platform to underwater communication. Waves at sea surface changes the
incident angle of incoming aerial laser beam dynamically. This effect leads to the beam dancing at receiver.
Maximum deviation of beam from normal may be 10.6(paper reference). In present experiment only intrawater disturbances are simulated using water churning motor placed at interval of 1.5m.Without churning and
with churning (RPM) average BER remains less 1 bit/Mb.
Turbulence
No churn
With churn

OOK
Av. BER(per 1Mb)
<1
< 1

PPM
<0.5
<0.5

3. Effect of ambient light on BER: Ambient light at the detector may lead to the receiver decision error.
Probability of discrimination between 1 and 0 decreases with increase in ambient light level. Ambient light
effect may be diminished by using very sharp laser line filters but fabrication of very narrow laser line width
(nm) filter is a great challenge worldwide Receiver should be very robust to handle the effect of ambient noise.
In the above setup BER is calculated under different light condition and keeping other error sources inactive.
Results are presented in the table below:

Light intensity
No light
100W bulb
| IJMER | ISSN: 22496645 |

OOK
Av. BER(per 1Mb)
<1
1-2
www.ijmer.com

PPM
<0.5
0.5-1
| Vol. 4 | Iss. 12 | Dec. 2014 | 64 |

BER Estimation for Laser Based Under Water Communication

4. Effect of laser ON-OFF stabilization rate on BER: Here we have used Nd-Yag laser rated 30 KHz TTL
modulation. it was observed that up to 10 KHz the laser works smoothly but after 10 KHz it starts missing
pulses. Due to these missed pulses there is an increase in the bit error rate.

frequency
10 KHz<
10KHz to 15 KHz
>15 KHz

OOK
Av. BER(per 1Mb)
<1
< 2.5
< 3.0-4.0

PPM
<0.5
<1
<1.5-2

III. Conclusion
As the salt content of water increases the bit error rate increases. Churning of water has no considerable
effect on the bit error rate. As the frequency of the laser is increased beyond 10 kHz the bit error rate increases
significantly. When the source of ambient light is brought very near to the receiver the BER increases drastically
and all the information content is lost. PPM modulation technique offers less BER as compared to OOK and
provides an improved overall performance.

REFERENCES
[1]
[2]

[3]
[4]

[5]

S. Luryi, M. Gouzman, Feasibility of an optical frequency modulation system for free-space optical
communications. International Journal of High Speed Electronic System, Volume 16, Issue 2, pp 559566. 2006.
Ziad T. Al Dahan , Samar Y. Al Dabagh and Asmahan Assad. Design and Implementation of Under Water Optical
Communication System, International Journal of Application or Innovation in Engineering & Management
(IJAIEM), Volume 2, Issue 6, June 2013.
X. Zhu, and J. M. Kahn, Free-space optical communication through atmospheric turbulence channels, IEEE Trans.
on Commun. 50, pp1293-1300. 2002.
Viorel Manea, Radu Dragomir, Sorin Puscoci. OOK and PPM modulations effects on bit error rate in terrestrial
laser transmissions, Institutul Naional de Studii i Cercetri pentru Comunicaii I.N.S.C.C, Telecomunicaii Anul
LIV volume 2, pp 56-58, 2011.
Yagimli Design of Laser Based Underwater Communication System. Journal of Naval Science and Engineering,
Volume 7, Issue 2, pp 1-10. 2011.

| IJMER | ISSN: 22496645 |

www.ijmer.com

| Vol. 4 | Iss. 12 | Dec. 2014 | 65 |