Edited by Foxit PDF Editor

Copyright (c) by Foxit Software Comp

For Evaluation Only.

COMPUTHERM Q7

Programmable digital room thermostat

NEW

software!

Operating Instructions

GENERAL DESCRIPTION OF THE THERMOSTAT

The COMPUTHERM Q7 type switched-mode room thermostat
is suitable to regulate the overwhelming majority of boilers and air
conditioners available
in Hungary. It can
easily be connected
to any gas boiler or
air conditioning device
that has a double wire
connector for a room
thermostat, regardless
of whether it has a 24V
230V AC
or 230V control circuit.
50-60 Hz
2

The device can be programmed according to customer-specific

requirements so that the heating/cooling system heats/cools your
residence or office to the required temperature at the dates and
times specified by you, to reduce energy costs while maintaining
comfort. Separate temperature programs can be prepared for each
day of the week. For each day, beside 1 fixed switching time, 6
adjustable switching times can be set and a different temperature
can be assigned to all 7 switching times.
The switching sensitivity of the thermostat can be set to
0.1C, 0.2C (default setting) or 0.3C. This figure means the
temperature difference between the adjusted value and the actual
temperature measured during the switching process. In case of the
0.2C switching sensitivity and heating mode for example, if the
set temperature is 20C, then the device switches the boiler on at
19.8C or below, and switches it off at 20.2C or above. Please refer
3

to Section 3.4 for the modification of the factory default switching

sensitivity of 0.2C.
The thermostat is equipped with a pump protection function,
which, to prevent the pump from sticking, switches on the boiler for
a one minute period at 12:00 p.m. every day if the pump has not
been switched on in a programmed manner for more than 24 hours
(e.g. outside the heating season). See the activation of the pump
protection function in Section 3.5.

The information shown on the liquid crystal

display of the thermostat includes the following:
Temperature modification
until the next manual
interference

The days of the week

Time

Set temperature
Manual control indicator

Programme number
Timed manual control
indication

Current temperature
of the room

Low battery voltage

Sign of heating/cooling

1. LOCATION OF THE DEVICE

It is reasonable to locate it in a room used regularly or for many hours
per day so that it is in the direction of natural ventilation in the room but
protected from drought or extreme heat (e.g. direct sunlight, refrigerator,
chimney, etc). Its optimal location is 1.5 m above floor level.
IMPORTANT WARNING! If the radiator valves in your flat
are equipped with a thermostatic head, adjust it to maximum
temperature or replace the thermostatic head of the radiator valve
with a manual control knob in the room where the room thermostat
is to be located, otherwise the thermostatic head may disturb the
temperature control of the flat.

2. INSTALLATION OF THE THERMOSTAT

Pressing the lock on the upper
side of the housing of the
thermostat, remove the back
cover of the thermostat as
shown in the figure.
With the help of the screws
provided and some tools fasten
the rear panel of the device to
the wall.
Using a small screwdriver,
remove the cover of the
terminal block from the inner
side of the rear panel. The
thermostat controls the boiler or

Vertical angle:
30 - 45

Latch

air conditioner through a potential-free alternating relay that has the

following connection points: No. 1 (NO); No. 2 (COM) and No. 3
(NC). These connection points are located under an inner cover on
the inner side of the rear panel.
Connect the two connection points of the heating or cooling
equipment to be controlled to terminals No. 1 (NO) and No. 2
(COM), i.e. to the normally open terminals of the relay.
If you would like to operate an old boiler or any other device that
has no connection points for thermostats, then the No. 1 (NO)
and No. 2 (COM) connection points of the thermostat should be
connected to the mains cable of the device, similarly as a switch
would be connected.
To prevent electric shock, replace the inner cover removed for
the connection of wires after the assembling process has been
completed.
8

Attention! Always consider the loadability of the thermostat

and follow the manufacturers instructions of the heating or cooling
equipment. The device must be installed and connected by a qualified
professional. The voltage appearing at terminals No. 1 and No. 2
depends only on the system being controlled, therefore the dimensions
of the wire are determined by the type of the device to be controlled.
The length of the wire is of no significance.

3. PUTTING THE THERMOSTAT INTO OPERATION,

BASIC SETTINGS

3.1 Inserting batteries

The battery compartment is in the inner side of the front panel
of the housing. Insert 2 AA alkaline batteries (LR6 type) in
accordance with the diagram in the battery compartment. After
the batteries have been inserted, the display flashes the day,
time and program number as well as the adjusted and measured
temperatures. (If this information fails to appear on the display,
press the RESET button with a wooden or plastic stick. To press
the button, do not use any electrically conductive materials, e.g.
graphite pencil.) After the batteries have been inserted, snap
the front panel of the device into the rear panel and press the
SET button. After the SET button is pressed, the display stops
10

flashing, the thermostat goes to the main screen and the setting
process can be started.
3.2 Setting the current day and time
Press the SET button to go to the main screen, then press the
DAY button. At this time only the serial number of the day will flash
on the display of the thermostat and the hour and minute values can
be seen.
Using the large
and
buttons on the front panel of the device,
set the serial number of the current day (Monday 1; Tuesday 2;
Wednesday 3, etc.). Press the DAY button again. At this time
the number indicating the day stops flashing and becomes visible
continuously while the numbers indicating the hour will flash on the
display. Using the large
and
buttons on the front panel of the
device, set the hour value of the current time. Press the DAY button
11

again. At this time the numbers that indicate the hour stop flashing
and become visible continuously, while the numbers indicating the
minute will begin flashing. Using the large
and
buttons on the
front panel of the device, set the minute value of the current time.
When you wish to continue modifying the settings, please press the
DAY button again. If you wish to finish settings, confirm them by
pressing the SET button. At this point adjusted data are recorded
and the device goes back to the main screen (if no buttons are pressed
for at least 15 seconds, the settings are automatically confirmed and the
device goes back to the main screen).
3.3 Switching between the heating and cooling mode
There is a possibility to easily switch between the heating and cooling
mode of the thermostat. The output terminals No. 1 and No. 2 of the
thermostat are closed below the set temperature in heating mode, and
12

they are closed above the set temperature in cooling mode (taking
the switching sensitivity into account). The closed state of the output
terminals No. 1 and No. 2 are indicated by the
icon in the bottom
left corner of the display in case of both modes.
To switch between the two modes, first press the SET button to go
to the main screen. Then press the SET button again and hold it
down and press the COPY button, too. After this, the notice HE AT
or
appears in place of the time characters, according to the
selected mode. Following this, switch between the modes using
the large
and
buttons, then confirm it by pressing the SET
button (if no buttons are pressed for at least 15 seconds, the setting is
automatically confirmed). After this confirmation, the device goes back
to the main screen.

13

3.4 Setting the switching sensitivity (accuracy)

The switching sensitivity means the temperature difference between
the adjusted value and the actual temperature measured during the
switching process. A smaller switching sensitivity results in steadier
room temperature and therefore in higher comfort. The heat loss of
the room (building) does not depend on the switching sensitivity.
If higher comfort is needed, the switching sensitivity should be
set so that it provides a steadier room temperature. On the other
hand, please also take into account that the boiler should not switch
on and off multiple times in an hours time except at low outside
temperatures (e.g. -10C), since the frequent on and off switches
of the boiler reduce its efficiency and hence increases the gas
consumption. We recommend using the 0.1C switching sensitivity
for heating systems with high thermal inertia (e.g. underfloor
heating), the 0.2C (factory default setting) and 0.3C switching
14

sensitivity for heating systems with low thermal inertia (e.g. flat
panel radiators).
To change the switching sensitivity, first press the SET button to go
to the main screen. Then press the DAY and COPY buttons one
after the other. Following this, select the desired switching sensitivity
using the large
and
buttons. The notices S:1 , S:2 and S:3
indicate 0.1C, 0.2C and 0.3C, respectively. Finally, confirm
the setting by pressing the SET button (if no buttons are pressed
for at least 15 seconds, the setting is automatically confirmed). After
this confirmation, the device goes back to the main screen.
3.5 Activation of the pump protection function
Under the factory default settings, the pump protection function is
inactive. In order to activate or deactivate it, first press the SET
15

button to go to the main screen. Then press the DAY and PROG
buttons one after the other. Following this, activate or deactivate this
function using the large
and
buttons. The notices HP:ON and
HP:OF indicate activated and deactivated state, respectively. Finally,
confirm the setting by pressing the SET button (if no buttons are
pressed for at least 15 seconds, the setting is automatically confirmed).
After this confirmation, the device goes back to the main screen.
To prevent the pump from sticking, the activated pump protection
function switches on the boiler for a one minute period at 12:00 p.m.
every day outside the heating season. (The pump protection function
can accomplish its task only if the boiler is in working order in the
summer, too. It is reasonable to set a low temperature level, e.g.
+10C, on the thermostat for this period, to prevent the boiler from
unnecessary start-ups when the weather turns cold temporarily).
16

3.6 Calibrating the thermometer of the thermostat

There is a possibility to calibrate the thermometer of the thermostat
(to correct the measured temperature). In order to do this, first press
the SET button to go to the main screen. Then press the DAY

and HOLD buttons one after the other. After this, the notice
appears in place of the time characters, and the correction value
appears in place of the measured temperature (0.0C by default).
Following this, set the desired correction value using the large
and
buttons between -3.0C and +3.0C, in 0.1C increments.
Finally, confirm the setting by pressing the SET button (if no buttons
are pressed for at least 15 seconds, the setting is automatically
confirmed). After this confirmation, the device goes back to the main
screen. The correction of the measured temperature takes effect a
couple of seconds after the confirmation.
17

4. PROGRAMMING THE THERMOSTAT

4.1 A brief introduction to programming
Programming means the setting of switching times and selection
of accompanying temperature levels. The device can be
programmed for a one-week period. Its operation is automatic,
and it will cyclically repeat the programs that have been keyed in.
For each day, beside 1 fixed switching time, 6 adjustable switching
times can be set. For all switching times a different temperature
can be assigned between 5 and 35C, in 0.5C increments. The
temperature set for a given switch will remain valid until the start
time of the next switch. Accordingly, the thermostat will keep
the temperature set for switching time P0 until switching time P1
is reached. After switching time P1 the temperature selected to
switch P1 will be valid until the time of the next switch (P2).
18

 The start time of switch P 0 is 00:00 , which cannot be

changed, only its temperature can be adjusted. So under
the factory default settings, the thermostat performs only
one switch ( P 0 ) every day, which is in effect from 00:00 until
00:00 the next day.
Note: Setting just one switch for a day (factory default setting) is
reasonable only if a constant temperature is needed all day. (For
example, if for every weekday a constant 16C, and for every
weekend a constant 22C is needed.) Otherwise, from both a
comfort and an energy-efficiency point of view, it is recommended
to activate more than one switch for each day. Furthermore, it
is advised that a comfort temperature is used only those times,
when the room or building is in use, since every 1C decrease
of temperature saves approximately 6% energy during a heating
season. As opposed to common belief, keeping a flat warm
19

requires more energy than heating it up. (When using a stove,

more gas is needed to keep a pan of water boiling than to just
keep it warm.)
The P1 - P6 switches are deactivated by factory default (their start
time is --:--), but they can be activated at need. Their start time
can be freely set between 00:10 and 23:50 at 10-minute intervals
given the constraint, that their start time should be in increasing
order and a difference of at least 10 minutes should be between
them. This minimum 10-minute difference is going to be preserved
even if a previously activated switch is modified, in order to avoid
co-occurring or overlapping switches. In such a case, the device
automatically increases the start time of the affected switches until
a difference of at least 10 minutes between them is reached. If the
start time of a switch would be later than 23:50 because of this
automatic modification, then that switch is deactivated instead.
20

 In order to enter the programming mode, press the SET button

and hold it down and press the PROG button, too. During the
programming the values being adjusted are flashing on the display.
The modification of these values can always be done using the
large
and
buttons. The confirmation of a value is always
done by pressing the PROG button, after which the next value
can be adjusted. The program can be saved by pressing the SET
button. A more detailed description of the programming steps can
be found in Section 4.3.
If there are days, for which the same program is needed, than it is
sufficient to create that program only once, since it can be easily
copied to another day using the COPY button as described in
Section 4.4. If the same program is needed for every day, then
there is also a possibility to create the program of all the days
together (by selecting 1 2 3 4 5 6 7 together during the selection
21

of days). But be aware: if the program of all the days are created
together, than their program can only be modified together.
Therefore, if a different program is needed for at least one day,
then the program of the days should be created separately, and the
repeated programs should be copied using the COPY button.
A separate program can be created for the heating and cooling
mode, and these programs are preserved when switching between
the modes. Therefore, if the thermostat is used for both heating and
cooling, then there is no need to modify the program of the thermostat
every time a switch between these modes is performed.
4.2 Recommendations for creating a heating program
The average comfort needs of a person can usually be satisfied by
a temperature of 19-21C during the night, and a temperature of 2223C during the day. During that time of the day, when the family is
22

at work or school, only a lower temperature is needed. As heating

up and cooling down usually takes a long time, it is reasonable to
set the start time of the switches 0.5-1 hour before the desired time
of the modified temperature. The programmability of the thermostat
provides a perfect solution for this.
For an average working family, a program similar to the one below
is recommended:
P0

00:00

P1

05:30

P2

07:00

P3

15:00

P4

22:00
23

20 C
22 C
18 C
22 C
20 C

Temperature

Time
00:00
20 C

5:30 7:00
22 C 18 C

15:00
22 C

24

22:00
20 C

4.3 Programming steps

a. Press the SET button to go to the main screen.
b. Press the SET button again and hold it down and press
the PROG button, too. At this point the device gets into
programming mode and the numbers indicating the days of the
week (1 2 3 4 5 6 7) are flashing on the display.
c. Select the day to be programmed using the large
and
buttons on the front panel of the device (1 indicating Monday, 2
indicating Tuesday etc.). If you wish to create the same program
for each day of the week, it is reasonable to choose all days of
the week simultaneously (by selecting 1 2 3 4 5 6 7 together),
this way there is no need to perform separate programming of
the days. After selecting the desired day(s), press the PROG
button.
25

d. At this point the temperature of switch P0 should be set,

which is indicated on the display of the device by flashing the
temperature value to be set (20 C by default). Set the desired
and
buttons, then press the
temperature using the large
PROG button.
e. Then, the start time of switch P1 should be adjusted, which is
indicated on the display of the device by flashing the time value
to be adjusted (--:-- by default). Set the desired time using the
and
buttons, then press the PROG button.
large
f. Following this, the temperature of switch P1 should be set,
which is indicated on the display of the device by flashing
the temperature value to be set (20 C by default). Set this
and
buttons,
temperature level of switch P1 using the large
then press the PROG button.
26

g. The next step in programming is the adjustment of the start

time of switch P2, which is indicated on the display of the
device by flashing the time value to be adjusted (--:-- by
default). The adjustment process of switches P2-P6 can be
done (the same way as switch P1 is adjusted) by repeating the
e-f steps.
If you do not want to activate any more switches for the selected
day(s), then press the PROG button without changing the
start time of the next switch from the default --:--. This way the
programming of the selected day(s) is finished, the thermostat
offers another day to be programmed and the programming
can be continued from step c.
If all the switches (P0-P6) are activated for the selected
day(s), then after setting the temperature value of P6, the
programming of the selected day(s) is finished, the thermostat
27

offers another day to be programmed and the programming

can be continued from step c.
h. The adjusted program can be saved by pressing the SET
button. After approximately 1 minute, the adjusted program is
automatically saved. Afterwards, the device goes back to the
main screen.
If you wish to copy the program of the day(s) selected in step c to other
days, you can easily do so using the COPY button as described in
Section 4.4.
4.4 Using the COPY function (Copying the program of a day to
other days)
First, press the SET button to go to the main screen. Then
press the COPY button for approximately 3 seconds to activate
28

the COPY function. The notice COPY appearing in place of

the time characters and the flashing serial number 1 indicating
Monday shows that conditions are ready for copying a program.
Select the day whose program you wish to copy to another day or
other days using the large
and
buttons on the front panel
of the device.
Press the COPY button to copy the program of the selected day.
After this, the flashing of the number indicating the day that has
been copied stops and it will be visible continuously hereafter.
Select the day to which you wish to copy the program of the day
copied beforehand using the large
and
buttons. The number
of the active day is flashing during this selection process.

29

 After selecting the number that indicates the day to which you wish
to copy the program, press the COPY button to copy the program.
Hereafter, the number indicating the day to which the program was
copied will be visible continuously. Following this, you can select
further days using the large
and
buttons and copy the
program to those days too by pressing the COPY button.
Finally, press the SET button to save the modifications (if no
buttons are pressed for at least 15 seconds, the modifications will
be automatically saved). Afterwards, the device goes back to the
main screen. If required, the program of further days can be freely
copied by repeating the above steps.
Attention! The COPY function is only available, if the days of the
week were programmed separately!
30

4.5 Modifying the program

The previously set program can be modified any time by repeating
the steps of programming.
The number of activated switches can be increased at will as
described in Section 4.3.
A previously activated switch can be deactivated by setting its
start time to --:-- using the large
and
buttons (or by
pressing the DAY button once), and then pressing the PROG
button. After this, if the deactivated switch was an intermediate
one, then the serial numbers of the remaining switches will be
updated.
If you wish to finish modifying the program of the selected day,
then press the PROG button and hold it down for at least 3
31

seconds. After this, the modification can be continued by selecting

another day. When finished with all the modifications, press the
SET button to save them. After approximately 1 minute, they are
automatically saved. Afterwards, the device goes back to the main
screen.
If a completely different program is needed, then press the RESET
button to reset the device (it deletes both the program and the
basic settings). To press the button, do not use any electrically
conductive materials, e.g. graphite pencil. Following this, adjust
the basic settings of the thermostat again and create the new
program, as described in Sections 3 and 4.

32

4.6 Program inspection

First, press the SET button to go to the main screen, then press
the PROG button. At this point, the serial number indicating the
day(s), the symbol of switch P0 and the time and temperature level
set for switch P0 of the selected day(s) will appear on the display
(none of the values is flashing).
Repeatedly press the PROG button to check the values of switch
and
buttons to change the day(s).
P2 , P3 , etc. Use the large
If all the days were programmed together (1 2 3 4 5 6 7), then their
common program can only be viewed together.
After checking the program, press the SET button to go back to
the main screen (if no buttons are pressed for at least 15 seconds,
the thermostat will automatically go back to the main screen).
33

5. TEMPORARY MODIFICATION OF THE TEMPERATURE

CORRESPONDING TO THE PROGRAM
If you wish to operate your device in a way that differs temporarily
from the program that has been set (e.g. on bank holidays or the
winter holidays), you can choose among the options described in
Sections 5.1-5.4.
To simplify manual temperature modifications, with factory default
settings temperatures of 18 C and 22 C are assigned to the large
and
buttons, respectively. When modifying the temperature
manually, pressing the
or
button once, the temperature will
immediately jump to the factory value of the button. For example,
if the current switch P3 ensures a temperature of 19C, it can
be modified to a standard temperature that ensures 22C when
needed by pressing the
button only once, without having to
34

press the
button several times in increments of 0.5C. Following
this, using the large
and
buttons, the temperature can be
further modified in increments of 0.5C, in accordance with current
requirements.
The economy and comfort temperature values assigned to
buttons
and
can be modified as follows:
To set the economy temperature, press the SET button and
button, too. Following this, with
keep it depressed and press the
and
buttons, set the economy temperature
the help of the
selected by you. After the temperature has been set, press the
SET button to save the modification (after approximately 15
seconds, it is automatically saved). Afterwards, the device goes
back to the main screen.
35

 To set the comfort temperature, press the SET button and keep
button, too. Following this, with
it depressed and press the
and
buttons, set the comfort temperature
the help of the
selected by you. After the temperature has been set, press the
SET button to save the modification (after approximately 15
seconds, it is automatically saved). Afterwards, the device goes
back to the main screen.
5.1 Temperature modification until the next program switch
and
buttons on
Set the required temperature using the large
the front panel of the device. At this time, the
icon appears on
the display, indicating that the thermostat is operated with manual
control. The device will control the boiler according to the set value
until the time of the next switch specified in the program is reached.
36

During this temporary modification, the segments indicating the

time on the display alternately show the exact time and the time
remaining in manual control (e.g. 1H:02, that is, 1 hour and 2
minutes). After this time has elapsed, the
icon disappears and
the device resumes the program that has been set. If you wish
to return to the set program before the time of the next switch is
reached, please press the SET button.
5.2 Temperature modification for 1-9 hours (party program)
and
buttons on
Set the required temperature using the large
the front panel of the device, and then press the DAY button. At
icon appears on the display, along with number
this time, the
1 in place of the switch number, which indicates the duration of
modification in hours. Adjust this time to the desired length (between
and
buttons. The party program will
1 and 9) using the large
37

start approximately 10 seconds after the adjustment. Following this,

the device will keep the modified temperature for the given period
of time. The adjusted temperature can be freely changed during the
party program without exiting it.
During this temporary modification, the segments indicating the time
on the display alternately show the exact time and the time remaining
in manual control (e.g. 3H:02, that is, 3 hours and 2 minutes).
icon disappears and the device
After this time has elapsed, the
resumes the program that has been set. If you wish to return to the
set program before the time set for temperature modification has
expired, please press the SET button.
5.3 Temperature modification for 1-99 days (holiday program)
and
buttons on
Set the required temperature using the large
the front panel of the device, and then press the HOLD button
38

and hold it down for at least 2 seconds. At this time, the

icon
appears on the display, along with the :01 notice in place of the
time characters, which indicates the duration of modification in days.
Adjust this time to the desired length (between 1 and 99) using
and
buttons (1 day means 24 hours). The holiday
the large
program will start approximately 10 seconds after the adjustment.
Following this, the device will keep the modified temperature for
the given period of time. The adjusted temperature can be freely
changed during the holiday program without exiting it.
During this temporary modification, the segments indicating the
time on the display alternately show the exact time and the days
remaining in manual control (e.g. :03, that is, 3 days). After
icon disappears and the device
this time has elapsed, the
resumes the program that has been set. If you wish to return to the
P

39

set program before the time set for temperature modification has
expired, please press the SET button.
5.4 Temperature modification until the next manual interference
and
buttons on
Set the required temperature using the large
the front panel of the device. At this time, the
icon appears on
the display, indicating that the thermostat is operated with manual
control. Then, press the HOLD button briefly, after which the
icon appears and the
icon disappears. The device will then
control the boiler according to the set value until the next manual
interference. During this time, the thermostat acts exactly the same
way as a non-programmable thermostat. The adjusted temperature
can be freely changed during this temporary modification without
exiting it.
40

If you wish to return to the set program, please press the SET
button.
6. TURNING ON THE BACKGROUND LIGHT
When you press the LIGHT button, the background light of the
display will turn on for 15 seconds. When you press another button
while the display is illuminated, the background light will turn off
only after 15 seconds have elapsed since the last button had been
pushed.
7. LOCKING THE CONTROL BUTTONS
The thermostat enables you to lock its control buttons. With this
function, you can prevent unauthorised modification of the program
41

or the set temperature. To activate the lock, first press the SET
and
buttons
button to go to the main screen, then press the
together and hold them down for at least 5 seconds. After the control
buttons have successfully been locked, the notice
appears in
place of the time characters for a couple of seconds. Until the control
buttons are locked, their normal function do not work; if any button
is pressed, then only the notice
appears and nothing else
happens. To unlock press the
and
buttons together and hold
them down for at least 5 seconds. After unlocking the buttons, the
notice
appears in place of the time characters for a couple of
seconds, whereupon all the buttons can be used normally again.

42

8. CHANGING THE BATTERY

The average lifetime of the batteries is 1 year, but frequent use
of the background light may shorten this time considerably. If the
icon indicating low battery voltage appears on the display, the
batteries should be replaced (see Section 3.1). The exact time
should be set again after the batteries have been replaced, but
the device saves the program that has been loaded even without
batteries therefore there is no need to reprogram the device.

43

9. RESETTING THE THERMOSTAT TO ITS FACTORY

DEFAULT SETTINGS

By pressing the RESET button, the thermostat can be reset to its

factory default settings. This results in deleting the day, exact time,
basic settings and the set program. To press the RESET button,
do not use any electrically conductive materials, e.g. graphite
pencil. After resetting the device, adjust the basic settings of the
thermostat again and create the new program, as described in
Sections 3 and 4.

44

TECHNICAL DATA
switchable voltage:
switchable current:
temperature measurement range:
adjustable temperature range:
temperature measurement accuracy:
temperature calibration range:
selectable switching sensitivity:
storage temperature:
battery voltage:
power consumption:
battery lifetime:
dimensions:
weight:
temperature sensor type:
45

24V AC/DC to 250V AC, 50Hz

8A (2A inductive load)
5 to 35C (in 0.1C increments)
5 to 35C (in 0.5C increments)
0.5C
3C (in 0.1C increments)
0.1C; 0.2C; 0.3C
-10C to +40C
2 x 1.5V alkaline batteries (LR6 type; AA size)
1.3mW
approx. 1 year
130 x 80 x 35mm
154g
NTC 10k 1% at 25C

A brief description of programming

Setting the date and time: press the DAY button, then adjust values using the
and
buttons.
DAY,
Programming: press and hold down the SET button, while pressing the PROG
and
buttons; use the
button too, then adjust values with the PROG,
COPY button to copy repeated programmes.
Program inspection: using the PROG,

and

buttons.

Temporary modification of the temperature set in the program:

until the next switch in the program: set the temperature using the
and
buttons.
and
for a period of 1 to 9 hours: set the temperature using the
buttons, then press the DAY button, and finally set the duration using the
and
buttons.
and
for a period of 1 to 99 days: set the temperature using the
buttons, then press the HOLD button and hold it down for 2 seconds, and
and
buttons.
finally set the duration using the
and
buttons,
until the next interference: set the temperature using the
then press the HOLD button briefly.