HIGHWAY DESIGN MANUAL

830-1
March 7, 2014

CHAPTER 830
TRANSPORTATION FACILITY
DRAINAGE

This section involves the hydraulic design

fundamentals necessary for properly sizing and
locating standard highway drainage features such
as:

Asphalt dikes and gutters.

Concrete curbs and gutters.

Index 831.1 - Basic Concepts

Median drains.

Roadway drainage involves the collection,

conveyance, removal, and disposal of surface
water runoff from the traveled way, shoulders,
sidewalks, and adjoining areas defined in Index
62.1(7) as comprising the roadway. Roadway
drainage is also concerned with the handling of
water from the following additional sources:

Roadside ditches

Overside drains.

Drop inlets.

Storm drains.

Topic 831 - General

Surface water from outside the right of way

and not confined to channels that would reach
the traveled way if not intercepted.

Crossroads or streets.

Irrigation of landscaped areas.

The design of roadway drainage systems often

involves consideration of the problems associated
with inadequate drainage of the adjacent or
surrounding area.
Cooperative drainage
improvement projects with the responsible local
agency may offer the best overall solution.
Cooperative agreements are more fully discussed
under Index 803.2
Some of the major considerations of good
roadway drainage design are:

Facility user safety.

Convenience to
pedestrian traffic.

Aesthetics.

Flooding of the transportation facility and

adjacent property.

Subgrade infiltration.

Potential erosion, pollution

environmental concerns.

Economy of construction.

Economy of maintenance.

vehicular,

bicycle

and

and

other

Removal of storm water from highway pavement

surfaces and median areas is more fully discussed
in FHWA Hydraulic Engineering Circular No. 22,
"Urban Drainage Design Manual". HEC 22
includes discussion of the effects of roadway
geometry on pavement drainage; the philosophy of
design storm frequency and design spread
selection; storm runoff estimating methods;
pavement and bridge deck inlets; and flow in
gutters. Charts and procedures are provided for
the hydraulic analysis and design of roadway
drainage features.

831.2 Highway Grade Line

In flat terrain, roadway drainage considerations
often control the longitudinal grade line of the
highway. A grade line that assures the desirable
goal of keeping the traveled way free of flooding
can usually be established for new freeway
projects and rural conventional highways.
For multilane urban highways with nearly
continuous dike or curb along the shoulder or
parking area, it is seldom practical to design the
highway with a gutter section which will contain
all of the runoff even from frequent rains. For this
reason the gutter and shoulder combination, and
often partial or full width of the traveled way, are
used to convey the runoff to inlets.

831.3 Design Storm and Water Spread

Before the hydraulic adequacy of roadway
drainage facilities can be analyzed, the quantity of
water (design Q) that the facility may reasonably
be expected to convey must be estimated. The
most important, and often the most difficult phase

830-2

HIGHWAY DESIGN MANUAL

March 7, 2014

of this task is the selection of an appropriate

design storm frequency for the specific project,
location or site under consideration. In order for a
design frequency to be meaningful criteria for
roadway drainage design, it must be tied to an
acceptable tolerance of flooding. Design water
spread, encroachment upon the roadbed or
adjacent property, is the tolerance of flooding
directly related to roadway drainage design.
Allowing too little spread is uneconomical in
design and too much spread may result in unsafe
driving conditions.
To optimize economy in roadway drainage, the
allowable water spread should vary, depending on
the type of project being designed. Because of the
effect of splash and spray on motorist visibility
and vehicle control, high volume roads with high
speed traffic cannot tolerate as much water spread
as urban streets. Likewise, the allowable water
spread should be minimized on urban streets
where a large number of pedestrians use adjacent
sidewalks
and
pedestrian
crosswalks.
Consideration should be given to the element of
motorist surprise when encountering intermittent
puddles rather than a continuous encroachment of
water on the driving lane. Eccentric forces are
exerted on a vehicle when one side encounters
water in the lane and the other side does not.
The probability of exceedance of the design storm
and the acceptable tolerance to flooding depends
on the importance of the highway and risks
involved. Selection of the design storm and water
spread parameters on rehabilitation and
reconstruction are generally controlled by existing
constraints.
In addition to the major roadway drainage
considerations previously listed, the following
more specific factors are to be considered in
establishing the project design storm:

Highway type

Traffic volume

Design speed

Local standards

The following geometric and design features of

the highway directly affect establishment of the
project design water spread:
Cross slope

Longitudinal slope

Number of lanes

Width of shoulders

Height of curb and dike

Parking lanes

Bus/Transit pullouts and loading areas

Desirable limits for water spread with respect to

design storm probability of exceedance are given
in Table 831.3. The parameters shown are
considered minimum roadway drainage design
standards for new freeway construction and for all
State highways with depressed sections which
require pumping. Local conditions may justify
less stringent criteria than the table parameters for
conventional highways. Exceptions should be
documented by memo to the project file.
It is often advantageous, to both the State and the
local agency, for highway drainage and street
drainage to be compatible. This is particularly
true in urban areas and rapidly developing
suburban areas where a conventional highway is,
or will become, part of the street network. Street
drainage criteria adopted by a local agency are
generally based on the hydrologic events peculiar
to a geographical area. Local drainage standards
that satisfy the needs of the community, usually
provide reasonable traffic safety and flood risk
considerations commensurate with those normally
expected for conventional highways in urban
areas.

831.4 Other Considerations

(1) Sheet Flow. Concentrations of sheet flow
across roadways are to be avoided. As a
general rule, no more than 0.10 cubic feet per
second should be allowed to concentrate and
flow across a roadway. Particular attention
should be given to reversal points of
superelevation where shoulder and gutter
slopes may direct flows across the roadway
and gore areas.
(2) Stage Construction. All permanent features of
roadway drainage systems should be designed
and constructed for the ultimate highway
facility.

HIGHWAY DESIGN MANUAL

830-3
May 7, 2012

Table 831.3
Desirable Roadway Drainage Guidelines
DESIGN STORM

DESIGN WATER SPREAD

4%
(25 yrs)

10%
(10 yrs)

Shldr or
Parking Lane

1/2 Outer
Lane

Local
Standard

--

--

--

--

--

--

--

--

--

High volume, multilane

Speeds over 45 mph.

--

--

--

High volume, multilane

Speeds 45 mph and under.

--

--

--

Low volume, rural

Speeds over 45 mph.

--

--

--

Urban
Speeds 45 mph and under.

--

--

--

HIGHWAY
Type/Category/Feature
FREEWAYS
Through traffic lanes, branch
connections, and other major ramp
connections.
Minor ramps.
Frontage roads.
CONVENTIONAL HIGHWAYS

ALL STATE HIGHWAYS

Depressed Sections That Require Pumping:
Use a 2% (50 yrs) design storm for freeways and conventional State highways. Design water spread at
depressed sections should not exceed that of adjacent roadway sections. A 4% (25 yr) design storm may be
used on local streets or road undercrossings that require pumping.

830-4

HIGHWAY DESIGN MANUAL

March 7, 2014

(3) Landscaping.
Runoff from existing or
proposed landscaping, including excess
irrigation water runoff, must be considered.
(4) Groundwater.
Groundwater is subsurface
water within a permeable strata. Depending
upon recharge and withdrawal rates the level of
the groundwater table can fluctuate greatly,
over a period of a few months or over periods
of many years. Consideration should be given
to recent history (several years of abnormally
wet or dry conditions) as well as the possibility
of revised practices by local water districts
(either increased pumping or increased
recharge).
Pipes located in areas where contact with
groundwater within their design life is likely
should have watertight joints. If groundwater
contact is likely and the surrounding soils are
highly erodible (fine grained sand, silty sand
and sandy silt/silt of limited cohesion)
consideration should be given to wrapping the
pipe joint with filter fabric. The fabric should
cover a length of 4 feet along the pipe, centered
on the joint. Groundwater at or above the
drainage system elevation will lead to
infiltration. Where this is undesirable, either
joint systems capable of resisting the
hydrostatic pressure, or dewatering measures,
should be incorporated into the design. The
design of groundwater control measures must
be coordinated with Geotechnical Services in
the Division of Engineering Services.
(5) Hydroplaning. Hydroplaning is the separation
of the tire from the road surface by a thin layer
of liquid (usually water) on the pavement. The
liquid separates the tire from the pavement
because of viscosity (viscous hydroplaning),
dynamic lift (dynamic hydroplaning), or a
combination of the two. Since water offers
little shear resistance, the tire loses its tractive
ability and the driver has a loss of control of
the vehicle. At locations where there is a
potential for hydroplaning, a careful review of
the wet weather accident rates should be made
using information obtained from the District
Traffic Branch. Typical situations that should
be evaluated for hydroplaning potential are:
*

Where three (3) lanes or more are sloped in

the same direction (see Topic 833).

Where the longitudinal grade and or cross

slope are less than minimum (Refer to
Index 204.3 for minimum grade and
Indexes 301.2 and 302.2 for cross slope).

Where there are poor pavement conditions

(rutting,
depressions,
inadequate
roughness).

Where water is allowed to concentrate

prior to being directed across the travel
lanes (see Index 831.4(1)).

Where re-striping projects will reduce

shoulder widths where dike, curb or
concrete barrier are present.

These situations may also be present on median

widening projects or projects involving
pavement rehabilitation and or lane addition on
multi-lane highways or freeways.
Speed and tire pressure appear to be a
significant factors in the occurrence of
hydroplaning, therefore, it is considered to be
the drivers responsibility to exercise prudence
and caution when driving during wet
conditions (California Basic Speed Law).
Designers do not have control over all of the
factors involved in hydroplaning. However,
remedial measures may be included in
development of a project to reduce
hydroplaning potential.
The following is
provided as guidance for the designer as
practical measures to consider:
(1) Pavement Sheet Flow

Maximize transverse slope (see Topic

833)

Maximize pavement roughness

Use of graded
pavements)

course

(porous

(2) Gutter Flow

Limit water spread to Table 831.3

Maximize interception of gutter flow

above superelevation transitions (see
Index 837.3)

(3) Sag Areas

HIGHWAY DESIGN MANUAL

830-5
March 7, 2014

Limit pond duration and depth (see

Topic 833)

(4) Overtopping

Avoid overtopping at cross culverts

using appropriate freeboard and/or
headwater elevation (see Topic 821)

Where
suitable
measures
cannot
be
implemented to address conditions such as
those identified above, or an identified existing
problem area, coordination should be made
with the Safety Review Committee per Index
110.7.

831.5 Computer Programs

There are many computer programs available to aid
highway design engineers with estimating runoff
and ensuing hydraulic design and analysis of
roadway drainage facilities.
Refer to Table 808.1 for guidance on selecting
appropriate software programs for specific analysis
needs.
Familiarity with the fundamentals of hydraulics and
traditional methods of solution are necessary to
assure that the results obtained are reasonable.
There is a tendency for inexperienced engineers to
accept computer output as valid without verifying
the reasonableness of input and output data.

Topic 832 - Hydrology

832.1 Introduction
The philosophy and principles of hydrology are
discussed in Chapter 810. Additional information
on methods of estimating storm runoff may be
found in FHWA's HEC 22.

832.2 Rational Method

With few exceptions, runoff estimates for roadway
drainage design are made by using Rational
Methods described under Index 819.2(1). In order
to make use of these methods, information on the
intensity, duration, and frequency of rainfall for the
locality of the project must be established. Refer to
Index 815.3(3) for further information on
precipitation intensity-duration-frequency (IDF)
curves that have been developed for many locations
in California.

832.3 Time of Concentration

Refer to Index 816.6 for information on time of
concentration.

Topic 833 - Roadway Cross

Sections
833.1 Introduction
The geometric cross section of the roadway affects
drainage features and hydraulic considerations.
Cross slope and width of pavement and shoulders
as well as other roadway geometry affect the rate of
runoff, width of tolerable spread, and hydraulic
design considerations.
The cross section of
drainage features such as, depressed medians, curbs
and gutters, dikes, and side ditches is often
controlled by an existing roadway geometric cross
section or the one selected for new highway
construction.

833.2 Grade, Cross Slope and

Superelevation
The longitudinal slope or grade is governed by the
highway grade line as discussed under Index 831.2.
Refer to Index 204.3 for minimum grade and
Indexes 301.2 and 302.2 for cross slope. Where
three (3) lanes or more are sloped in the same
direction, it is desirable to counter the resulting
increase in flow depth by increasing the cross slope
of the outermost lanes. The two (2) lanes adjacent
to the crown line should be pitched at the normal
slope, and successive lane pairs, or portions thereof
outward, should be increased by about 0.5 to
1 percent. The maximum pavement cross slope
should be limited to 4 percent.
However,
exceptions to the design criteria for cross slope in
Index 302.2 must be formally approved in
accordance with the requirements Index 82.2,
"Approvals for Nonstandard Design." For projects
where lanes will be added on the inside of divided
highways, or when widening an existing crowned
2-lane highway to a 4-lane divided highway,
consideration should be given to the use of a tent
section in order to minimize the number of lanes
sloping in the same direction. Refer to Index
301.2. Consideration should be given to increasing
cross slopes in sag vertical curves, crest vertical
curves, and in sections of flat longitudinal grades.
Superelevation is discussed in Topic 202. Refer to
Index 831.4 for Hydroplaning considerations.

830-6

HIGHWAY DESIGN MANUAL

March 7, 2014

Topic 834 - Roadside Drainage

834.1 General
Median drainage, ditches and gutters, and overside
drains are some of the major roadside drainage
facilities.

834.2 Median Drainage

(1) Drainage Across the Median. When it is
necessary for sheet flow to cross flush medians,
it should be intercepted by the use of slotted
drains or other suitable alternative facilities.
See Standard Plan D98-B for slotted drain
details.
Where floodwaters are allowed to cross
medians, designers must consider the impacts
of railings, barrier or other obstructions to both
the depth and spread of flow. Designers should
consult their district hydraulic unit for
assistance.
(2) Grade and Cross Slope. The longitudinal slope
or grade for median drainage is governed by
the highway grade line as discussed under
Index 831.2.
Refer to Index 204.3 for
minimum grade and Indexes 305.2 and
405.5(4) for standards governing allowable
cross slope of medians.
Existing conditions control median grades and
attainable cross slope on rehabilitation projects.
The flattest desirable grade for earth medians is
0.25 percent and 0.12 percent for paved gutters
in the median.
(3) Erosion. When velocities are excessive for soil
conditions, provisions for erosion control
should be provided. See Table 865.2 for
recommended permissible velocities for
unlined channels.
Economics and aesthetics are to be taken into
consideration in the selection of median
erosion control measures. Under the less
severe conditions, ground covers of natural or
synthetic materials which render the soil
surface stable against accelerated erosion are
adequate. Under the more severe conditions,
asphalt or concrete ditch paving may be
required.
Whenever median ditch paving is necessary,
consideration should be given to the use of

cement or lime treatment of the soil.

The
width treated will depend on the capacity
needed to handle the drainage. A depth of
6 inches is generally satisfactory. The amount
of cement or lime to be used should be based
on laboratory tests of the in-place material to
be tested, and normally varies from 6 percent to
10 percent. If a clear or translucent curing
compound is used, the completed area is
unobtrusive and aesthetically pleasing.
Asphalt concrete ditch paving and soil cement
treatments cured with an application of liquid
asphalt are highly visible and tend to become
unsightly from streaks of eroded material.
Cobbles, though effective for erosion control,
are not satisfactory in a recovery area for out of
control vehicles. See Topic 872 for further
discussion on erosion protection and additional
types of ditch linings.
Erosion control
references are given under Index 871.3.
(4) Economy in Design. Economy in median
drainage can be achieved by locating inlets to
utilize available nearby culverts or the collector
system of a roadway drainage installation. The
inlet capacity can be increased by placing it in
a local depression. Use of slotted pipe at sag
points where a local depression might be
necessary may be an alternative solution to a
grate catch basin.

834.3 Ditches and Gutters

(1) Grade. The flattest grade recommended for
design is 0.25 percent for earth ditches and
0.12 percent for paved ditches.
(2) Slope Ditches. Slope ditches, sometimes called
surface, brow, interception, or slope protection
ditches, should be provided at the tops of cuts
where it is necessary to intercept drainage from
natural slopes inclined toward the highway.
When the grade of a slope ditch is steep enough
that erosion would occur, the ditch should be
paved. Refer to Table 865.2 for permissible
velocities for unlined channels in various types
of soil. When the ditch grade exceeds a 4:1
slope, a downdrain is advisable. Slope ditches
may not be necessary where side slopes in
favorable soils are flatter than 2:1 or where
positive erosion control measures are to be
instituted during construction.

HIGHWAY DESIGN MANUAL

830-7
March 7, 2014

(3) Side Gutters. These are triangular gutters

adjoining the shoulder as shown in Figures
307.2 and 307.5. The main purpose of the
3 feet wide side gutter is to prevent runoff from
the cut slopes on the high side of
superelevation from flowing across the
roadbeds. The use of side gutters in tangent
alignment should be avoided where possible.
Local drainage conditions, such as in snow
areas, may require their use on either tangent or
curved alignment in cut sections. In snow
areas it may be necessary to increase the width
of side gutters from 3 feet to 6 feet. The slope
from the edge of the shoulder to the bottom of
the gutter should be no steeper than 6:1. The
structural section for paved side gutters should
be adequate to support maintenance equipment
loads.
(4) Dikes. Dikes placed adjoining the shoulder, as
shown in Figures 307.2, 307.4, and 307.5,
provide a paved triangular gutter within the
shoulder area. For conditions governing their
use, see Index 303.3.
(5) Chart Solutions.
Charts for solutions to
triangular channel flow problems are contained
in FHWA Hydraulic Engineering Circular No.
22, "Urban Drainage Design Manual".

834.4 Overside Drains

The purpose of overside drains, sometimes called
slope drains, is to protect slopes against erosion.
They convey down the slope drainage which is
collected from the roadbed, the tops of cuts, or
from benches in cut or fill slopes. They may be
pipes, flumes or paved spillways.
(1) Spacing and Location.
The spacing and
location of overside drains depend on the
configuration of the ground, the highway
profile, the quantity of flow and the limitations
on flooding stated in Table 831.3. When
possible, overside drains should be positioned
at the lower end of cut sections. Diversion
from one watershed to another should be
avoided. If diversion becomes necessary, care
should be used in the manner in which this
diverted water is disposed.
Overside drains which would be conspicuous
or placed in landscaped areas should be
concealed by burial or other means.

(2) Type and Requirement. Following are details

of various types of overside drains and
requirements for their use:
(a) Pipe Downdrains. Metal and plastic pipes
are adaptable to any slope. They should be
used where side slopes are 4:1 or steeper.
Long pipe downdrains should be anchored.
The minimum pipe diameter is 8 inches but
large flows, debris, or long pipe
installations may dictate a larger diameter.
Watertight joints are necessary to prevent
leakage which causes slope erosion.
Economy in long, high capacity
downdrains is achieved by using a pipe
taper in the initial reach. Pipe tapers
should insure improved flow characteristics
and permit use of a smaller diameter pipe
below the taper. See Standard Plan D87-A
for details.
(b) Flume Downdrains. These are rectangular
corrugated metal flumes with a tapered
entrance. See the Standard Plan D87-D for
details. They are best adapted to slopes
that are 2:1 or flatter but if used on 1.5:1
slopes, lengths over 60 feet are not
recommended.
Abrupt changes in
alignment or grade should be avoided.
Flume downdrains should be depressed so
that the top of the flume is flush with the
fill slope.
(c) Paved Spillways.
Permanent paved
spillways should only be used when the
side slopes are flatter than 4:1. On steeper
slopes a more positive type of overside
drain such as a pipe downdrain should be
used.
Temporary paved spillways are effective in
preserving raw fill slopes that are 6:1 or
flatter in friable soils during the period
when protective growth is being
established. Paved spillways should be
spaced so that a dike 2 inches high placed
at the outer edge of the paved shoulder will
effectively confine drainage between
spillways. When it is necessary to place a
spillway on curved alignment, attention
must be given to possible overtopping at
the bends.
See Index 868.2(3) for

830-8

HIGHWAY DESIGN MANUAL

March 7, 2014

discussion of superelevation of the water

surface.
(3) Entrance Standards. Entrance tapers for pipes
and flume downdrains are detailed on the
Standard Plans. Pipe entrance tapers should be
depressed at least 6 inches.
The local depressions called "paved gutter
flares" on the Standard Plans are to be used at
all entrance tapers. See Standard Plans D87-A
and D87-D for details and Index 837.5 for
further discussion on local depressions.
In areas where local depressions would
decrease safety the use of flush grate inlets or
short sections of slotted drain for entrance
structures may be necessary.
(4) Outlet Treatment. Where excessive erosion at
an overside drain outlet is anticipated, a simple
energy dissipator should be employed.
Preference should be given to inexpensive
expedients such as an apron of broken concrete
or rock, a short section of pipe placed with its
axis vertical with the lowermost 6 inches filled
with coarse gravel or rock, or a horizontal tee
section which is usually adequate for
downdrain discharges.
(5) Anchorage. For slopes flatter than 3:1 overside
drains do not need to be anchored. For slopes
3:1 or steeper overside drains should be
anchored with 6 foot pipe stakes as shown on
the Standard Plans to prevent undue strain on
the entrance taper or pipe ends. For drains over
150 feet long, and where the slope is steeper
than 2:1, cable anchorage should be considered
as shown on the Standard Plans. Where the
cable would be buried and in contact with soil,
a solid galvanized rod should be used the
buried portion and a cable, attached to the rod,
used for the exposed portion. Beyond the
buried portion, a slip joint must be provided
when the installation exceeds 60 feet in length.
Regard-less of pipe length or steepness of
slope, where there is a potential for hillside
movement cable anchorage should be
considered.
When cable anchorage is used as shown on the
Standard Plans, the maximum allowable
downdrain lengths shall be 200 feet for a slope
of 1.5:1 and 250 feet for a slope of 2:1. For

pipe diameters greater than 24 inches, or

downdrains to be placed on slopes steeper than
1.5:1, special designs are required. Where there
is an abrupt change in direction of flow, such
as at the elbow or a tee section downstream of
the end of the cable anchorage system,
specially designed thrust blocks should be
considered.
(6) Drainage on Benches. Drainage from benches
in cut and fill slopes should be removed at
intervals ranging from 300 feet to 500 feet.
(7) Selection of Types. Pipe and flume downdrains
may consist of either corrugated steel,
corrugated aluminum, or any other approved
material that meets the minimum design
service life required under Chapter 850. Refer
to Index 855.2 for additional discussion on
limitations of abrasive resistance of aluminum
pipe culverts.

Topic 835 - Dikes and Berms

835.1 General
Dikes and berms are to be used only as necessary to
confine drainage and protect side slopes susceptible
to erosion.

835.2 Earth Berms

(Text Later)

835.3 Dikes
Details of dikes are shown on Standard Plan A87.
See Topic 303 for a detailed discussion on the
types and placement considerations for dikes.

Topic 836 - Curbs and Gutters

836.1 General
The primary reason for constructing curbs and
gutters may be for delineation or pedestrian traffic
rather than for drainage considerations. Refer to
Topic 303 for further discussion and Standard Plan
A87 for details on concrete curbs and gutters.
Whatever the justification for constructing curbs
and gutters, they will usually have an effect on
surface water runoff and result in becoming a
roadway drainage design consideration.

HIGHWAY DESIGN MANUAL

830-9
March 7, 2014

836.2 Gutter Design

(1) Capacity. Gutters and drainage facilities are to
be designed to keep flooding within the limits
given in Table 831.3. Easy solutions to gutter
flow problems can be obtained by using the
charts contained in FHWA Hydraulic
Engineering Circular No. 22, "Urban Drainage
Design Manual" which applies to triangular
channels and other shapes illustrated in the
charts. Parked cars reduce gutter capacity and
also can cause water to shoot over the curb.
The downstream ends of driveway ramps can
also cause water to flow over the curb. As a
rule of thumb, gutter capacity should be
determined on a depth equal to 0.5 the curb
height for grades up to 10 percent and 0.4 the
curb height for grades over 10 percent in
locations where parking is allowed or where
driveways are constructed.
(2) Grade and Cross Slope. The longitudinal
grade of curbs and gutters is controlled by the
highway grade line as discussed under Index
831.2.
The cross slope of standard gutters is typically
8.33 percent toward the curb. Pavement slopes
on superelevated roadways extend the full
width of the gutter, except that gutter slopes on
the low side should be not less than
8.33 percent. Because they cut down gutter
capacity and severely reduce inlet efficiency,
cross slopes flatter than 8.33 percent should be
avoided, except where gutters are adjacent to
curb ramps where ADA requirements limit the
slope to a maximum of 5 percent.
(3) Curbed Intersections. If pedestrian traffic is a
ruling factor, intersection drainage presents the
following alternatives to be weighed as to
effectiveness and economy.
(a) Intercept the whole flow upstream of the
crosswalk.
(b) Intercept a part of the water and allow the
overflow to cross the intersection. The
width of flow should be controlled so that
pedestrian traffic is not unduly hampered.
(c) If flow is small, pass the entire flow across
the intersecting street in a valley gutter.

(4) Valley Gutters. Valley gutters across the

traveled way of the highway should not be
used. Valley gutters may be used across
intersecting streets and driveways, however, at
intersections with high traffic volumes on all
approaches, it is desirable to intercept all gutter
flow upstream of the intersection and avoid the
use of valley gutters. Valley gutters are also
undesirable along streets where speeds are
relatively high.
In locations of frequent
intermittent low flows, the use of valley gutters
with slotted drains should be considered. In
general, the total width of gutters should not
exceed 6 feet and cross slopes should not
exceed 3 percent. Two percent is suggested
where more than nominal speeds are involved.

Topic 837 - Inlet Design

837.1 General
The basic features of standard storm drain inlets are
shown in Figure 837.1. Full details appear on
Standard Plan D72 through D75, D98-A and D98B. The variety of standard designs available is
considered sufficient to any drainage situation;
hence, the use of nonstandard inlets should be rare.

837.2 Inlet Types

From an operating standpoint, there are five main
groups of inlets; these are:
(1) Curb-Opening. Curb opening inlets have an
opening parallel to the direction of flow in the
gutter. This inlet group is adapted to curb and
gutter installations. The curb opening is most
effective with flows carrying floating debris.
As the gutter grade steepens, their interception
capacity decreases. Hence, they are commonly
used on grades flatter than 3 percent.
When curb opening inlets are used on urban
highways other than fenced freeways, a
3/4 inch plain round protection bar is placed
horizontally across any curb or wall opening
whose height is 7 inches or more. The
unsupported length of bar should not exceed
7 feet. Use of the protection bar on streets or
roads under other jurisdiction is to be governed
by the desires of the responsible authorities.

830-10

HIGHWAY DESIGN MANUAL

March 7, 2014

The Type OS and OL inlets are only used with

Type A or B curbs. A checkered steel plate
cover is provided for maintenance access.
The Type OS inlet has a curb opening 3.5 feet
long. Since a fast flow tends to overshoot such
a short opening, it should be used with caution
on grades above 3 percent.
The Type OL inlet is a high capacity unit in
which the length of curb opening ranges from
7 feet to 21 feet.
(2) Grate. Grate inlets provide a grate opening in
the gutter or waterway. As a class, grate inlets
perform satisfactorily over a wide range of
gutter grades. Their main disadvantage is that
they are easily clogged by floating trash and
should not be used without a curb opening
where total interception of flow is required.
They merit preference over the curb opening
type on grades of 3 percent or more. Gutter
depressions, discussed under Index 837.5,
increase the capacity of grate inlets. Grate
inlets may also be used at locations where a
gutter depression is not desirable. See the
Standard Plans for grate details.
Locate grate inlets away from areas where
bicycles or pedestrians are anticipated
whenever possible. Grate designs that are
allowed where bicycle and pedestrian traffic
occurs have smaller openings and are more
easily clogged by trash and debris and are less
efficient at intercepting flow. Additional
measures may be necessary to mitigate the
increased potential for clogging.
The grate types depicted on Standard Plan
D77B must be used if bicycle traffic can be
expected. Many highways do not prohibit
bicycle traffic, but have inlets where bicycle
traffic would not be expected to occur (e.g.,
freeway median). In such instances, the
designer may consider use of grates from
Standard Plan D77A. The table of final pay
weights on Standard Plan D77B indicates the
acceptable grate types to be used for each listed
type of inlet.
If grate inlets must be placed within a
pedestrian path of travel, the grate must be
compliant with the Americans with Disabilities
Act (ADA) regulations which limit the

maximum opening in the direction of

pedestrian travel to no more than 0.5 inch.
Presently, the only standard grating which
meets such restrictive spacing criterion is the
slotted corrugated steel pipe with heel guard, as
shown in the Standard Plans. Because small
openings have an increased potential for
clogging, a minimum clogging factor of
50 percent should be assumed; however, that
factor should be increased in areas prone to
significant debris. Other options which may be
considered are grated line drains with specialty
grates (see the Standard Plans for grated line
drain details, and refer to manufacturers
catalogs for special application grates) or
specially designed grates for standard inlets.
The use of specially designed grates is a
nonstandard design that must be approved by
the Office of State Highway Drainage Design
prior to submittal of PS&E.
(3) Combination. Combination inlets provide both
a curb opening and a grate. These are high
capacity inlets which make use of the
advantages offered by both kinds of openings.
(a) Type GO and GDO. These types of inlets
have a curb opening directly opposite the
grate. The GDO inlet has two grates
placed side by side and is designed for
intercepting a wide flow. A typical use of
these inlets would be in a sag location
either in a curb and gutter installation or
within a shoulder fringed by a dike. When
used as the surface inlet for a pumping
installation, the trash rack shown on the
Standard Plan D74B is provided.
(b) Type GOL. This is called a sweeper inlet
because the curb opening precedes the
grate. It is particularly useful as a trash
interceptor during the initial phases of a
storm. When used in a grade sag, the
sweeper inlet can be modified by providing
a curb opening on both sides of the grate.
(4) Pipe.
Pipe drop inlets are made of a
commercial pipe section of concrete or
corrugated metal. As a class, they develop a
high capacity and are generally the most
economical type. This type of inlet is intended
for uses outside the roadbed at locations that

HIGHWAY DESIGN MANUAL

830-11
March 7, 2014

will not be subjected to normal highway wheel

loads.
Two kinds of inlets are provided; a wall
opening and a grate top. The wall opening
inlet should only be used at protected locations
where it is unlikely to be hit by an out of
control vehicle.
(a) Wall Opening Intake. This opening is
placed normal to the direction of surface
flow.
It develops a high capacity
unaffected by the grade of the approach
waterway. The inlet capacity is increased
by depressing the opening; also by
providing additional openings oriented to
intercept flows from different directions.
When used as the surface intake to a
pumping installation, a trash rack across
the opening is required. See Standard
Plans for pipe inlet details. Because this
type of inlet projects above grade, its use
should be avoided in areas subject to traffic
leaving the roadway.
(b) Grate Intake. The grate intake intercepts
water from any direction. For maximum
efficiency, however, the grate bars must be
in the direction of greatest surface flow.
Being round, it is most effective for flows
that are deepest at the center, as in a valley
median.
(5) Slotted Drains. This type of inlet is made of
corrugated metal or polyethylene pipe with a
continuous slot on top. This type of inlet can be
used in flush, all paved medians with
superelevated sections to prevent sheet flow
from crossing the centerline of the highway.
Short sections of slotted drain may be used as
an alternate solution to a grate catch basin in
the median or edge of shoulder.
Drop inlets or other type of cleanout should be
provided at intervals of about 100 feet.
(6) Grated Line Drains. This type of inlet is made
of monolithic polymer concrete with a ductile
iron frame and grate on top. This type of inlet
can be used as an alternative at the locations
described under slotted drains, preferably in
shoulder areas away from traffic loading.
However, additional locations may include
localized flat areas of pavement at private and

public intersections, superelevation transitions,

along shoulders where widening causes a
decrease to allowable water spread, tollbooth
approaches, ramp termini, parking lots and on
the high side of superelevation in snow and ice
country to minimize black ice and sheet flow
from snow melt. Removable grates should not
be placed where subject to traffic.
Short sections of grated line drain may be used
in conjunction with an existing drainage inlet
as a supplement in sag locations. However,
based on the depth of the water, the flow
condition will be either weir or orifice. The
transition between weir and orifice occurs at
approximately 7 inches depth of flow. The
HEC-22 method of design for slotted pipe is
recommended as the basis for grated line drain
design. It should be noted that this is inlet
interception/capacity design, not the carrying
capacity of the product as a conduit.
Furthermore, the grated line drain has a smaller
cross sectional area than slotted pipe, and
therefore typically less carrying capacity.
Grated line drains are recommended as an
alternative to slotted pipe at locations
susceptible to pipe clogging from sediments
and debris. Self-cleaning velocities can usually
be generated from their smooth interior surface,
or if necessary by specifying the optional presloped sections.
Grated line drains may also be useful where
there is a potential for utility conflicts with
slotted drains, which are generally installed at a
greater depth.
At locations where clean out access is needed,
removable grates can be specified. In areas
with pedestrian traffic, special grates which
meet the Americans with Disabilities Act
(ADA) requirements are mandatory. This type
of grate is susceptible to clogging, therefore
removable grates are recommended at these
locations, and they should only be specified
when placement directly within the pedestrian
path of travel is unavoidable.
(7) Scuppers. This type of inlet consists of a low,
rectangular slot cut through the base of a
barrier. Similar to, but smaller than curb
opening inlets (See Index 837.2(1)), scuppers

830-12

HIGHWAY DESIGN MANUAL

May 7, 2012

Figure 837.1
Storm Drain Inlet Types

HIGHWAY DESIGN MANUAL

830-13
September 1, 2006

Figure 837.1
Storm Drain Inlet Types (Cont.)

830-14

HIGHWAY DESIGN MANUAL

March 7, 2014

are prone to clogging by sediment and debris

and require enhanced maintenance attention.
Scupper interception efficiency decreases with
increased longitudinal gradient and scupper
design is not typically compatible with
construction of an inlet depression. Scuppers
are typically considered only when other inlet
options are infeasible.

837.3 Location and Spacing

(1) Governing Factors. The location and spacing
of inlets depend mainly on these factors:

At depressed grade lines under structures, care

must be taken to avoid bridge pier footings.
See Index 204.6.

(a) The amount of runoff,

(b) The longitudinal grade and cross slope,
(c) The
location
and
geometrics
of
interchanges and at-grade intersections,
(d) Tolerable water spread, see Table 831.3,
(e) The inlet capacity,
(f) Accessibility
inspection,

for

maintenance

In urban areas, the volume and movements of

vehicles, bicyclists, and pedestrians constitute
an important control. For street or road
crossings, the usual inlet location is at the
intersection at the upstream end of the curb or
pavement return and clear of the pedestrian
crosswalk. Where the gutter flow is small and
vehicular, bicycle, and pedestrian traffic are not
important considerations, the flow may be
carried across the intersection in a valley gutter
and intercepted by an inlet placed downstream.
See Index 836.2(4).

and

(g) Volume and movements of motor vehicles,

bicycles and pedestrians,
(h) Amount of debris, and
(i) The locations of public transit stops.
(2) Location. There are no ready rules by which
the spacing of inlets can be fixed; the most
effective and economical installation should be
the aim.
The following are locations where an inlet is
nearly always required:

Sag points

Points of superelevation reversal

Upstream of ramp gores

Upstream and downstream of bridges

bridge drainage design procedure
assumes no flow onto bridge from
approach roadway, and flow off bridge
to be handled by the district.

Intersections

Upstream of pedestrian crosswalks

Upstream of curbed median openings

Safety of location for maintenance purposes is

an important consideration. Wall opening
inlets should not be placed where they present
an obstacle to maintenance equipment and to
vehicles that leave the traveled way. Grate top
inlets should be installed in such locations.
Placement of inlets within the traveled way is
discouraged. Inlets should typically be
relocated when roadways are widened or
realigned. Any proposal to leave an existing or
construct a new inlet within the traveled way
should be discussed with District Maintenance
to verify that future access is feasible.
(3) Spacing. Arbitrary spacing of inlets should be
avoided. The distance between inlets should be
determined by a rational analysis of the factors
mentioned above. Detailed procedures for
determining inlet spacing are given in FHWA
Hydraulic Engineering Circular No. 22, "Urban
Drainage Design Manual". In a valley median,
the designer should consider the effect of inlet
spacing on flow velocities where the soil is
susceptible to erosion. To economize on
disposal facilities, inlets are often located at
culverts or near roadway drainage conduits.
(4) Inlets in Series. Where conditions dictate the
need for a series of inlets, the recommended
minimum spacing should be approximately
20 feet to allow the bypass flow to return to the
curb face.

HIGHWAY DESIGN MANUAL

830-15
March 7, 2014

837.4 Hydraulic Design

(1) Factors Governing Inlet Capacity.
capacity is a variable which depends on:

Inlet

(a) The size and geometry of the intake

opening,
(b) The velocity and depth of flow and the
gutter cross slope just upstream from the
intake, and
(c) The amount of depression of the intake
opening below the flow line of the
waterway.
(2) General Notes.
(a) Effect of Grade Profile. The grade profile
affects both the inlet location and its
capacity. The gutter grade line exerts such
an influence that it often dictates the choice
of inlet types as well as the gutter treatment
opposite the opening. See Index 831.2.
Sag vertical curves produce a flattening
grade line which increases the width of
flow at the bottom. To reduce ponding and
possible sedimentation problems, the
following measures should be considered:

Reduce the length of vertical curve.

Use a multiple installation consisting

of one inlet at the low point and one or
more inlets upstream on each side.
Refer to HEC 22 for further discussion
and design procedures for locating
multiple inlets.
Short sections of slotted or grated line
drains on either side of the low point
may be used to supplement drop inlets.

(b) Cross Slope for Curbed Gutters. Make the

cross slope as steep as possible within
limits stated under Index 836.2(2). This
concentrates the flow against the curb and
greatly increases inlet capacity.
(c) Local Depressions. Use the maximum
depression consistent with site conditions;
for further details see Index 837.5.
(d) Trash. The curb-opening type inlet, when
the first in a series of grate inlets, may
intercept trash and improve grate

efficiency. In a grade sag, one trash

interceptor should be used on each side of
the sump.
(e) Design Water Surface Within the Inlet.
The crown of the outlet pipe should be low
enough to allow for pipe entrance losses
plus a freeboard of 0.75 feet between the
design water surface and the opening at the
gutter intake.
This allows sufficient
margin for turbulence losses, and the
effects of floating trash.
(f) Inlet Floor.
The inlet floor should
generally have a substantial slope toward
the outlet. In a shallow drain system where
conservation of head is essential, or any
system where the preservation of a
nonsilting velocity is necessary, the half
round floor shown on the Standard Plan
D74C should be used when a pipe
continues through the inlet.
(g) Partial Interception. Economies may be
achieved by designing inlets for partial
interception with the last one or two inlets
in series intercepting the remaining flow.
See Hydraulic Engineering Circular No.
22.
(3) Curb-Opening Inlets.
Gutter depressions
should be used with curb-opening inlets. The
standard gutter depressions for curb-opening
inlets, shown on Standard Plan D78 are
0.1 foot and 0.25 foot deep.
Curb-opening inlets are most economical and
effective if designed and spaced to intercept
only 85 to 90 percent of the flow. This
provides for an increased flow depth at the curb
face.
Figure 4-11, "Comparison of Inlet Interception
Capacity, Slope Variable", and Figure 4-12,
"Comparison of Inlet Interception Capacity,
Flow Rate Variable" of Hydraulic Engineering
Circular No. 22 can be used to obtain
interception capacities for various longitudinal
grades, cross slopes, and gutter depressions.
Charts for determining interception capacities
under sump conditions are also available in
HEC No. 22.

830-16

HIGHWAY DESIGN MANUAL

March 7, 2014

(4) Grate Inlets. The grate inlet interception

capacity is equal to the sum of the frontal flow
(flow over the grate) interception and the side
flow interception.
The frontal flow
interception will constitute the major portion of
the grate interception. In general, grate inlets
will intercept all of the frontal flow until a
velocity is reached at which water begins to
splash over the grate. Charts provided in HEC
22 can be used to compute grate interception
capacities for the various grates contained
therein. Grate depressions will greatly increase
inlet capacity.
The HEC 22 charts neglect the effects of debris
and clogging on inlet capacity. In some
localities inlet clogging from debris is
extensive, while in other locations clogging is
negligible. Local experience should dictate the
magnitude of the clogging factor, if any, to be
applied. In the absence of local experience,
design clogging factors of 33 percent for
freeways and 50 percent for city streets may be
assumed.
Grate type inlets are most economical and
effective if designed and spaced to intercept
only 75 to 80 percent of the gutter flow.
(5) Combination Inlets.
(a) Type GO and GDO Inlet. For design
purposes, only the capacity of the grates
need be considered. The auxiliary curb
opening, under normal conditions, offers
little or no increase in capacity; but does
act as a relief opening should the grate
become clogged. Since the grates of Type
GDO are side by side, the inlet capacity is
the combined capacity of the two grates.
(b) Type GOL Inlet. The interception capacity
of this inlet, a curb-opening upstream of a
grate, is equal to the sum of the capacities
for the two inlets except that the frontal
flow and thus interception capacity of the
grate is reduced by interception at the curb
opening.
(6) Pipe Drop Inlets.
(a) Wall Opening Intake. The standard intake
opening 2 feet wide and 8 inches to
12 inches deep provides a capacity of

approximately 6.0 CFS when the water

surface is 1 foot higher than the lip of the
opening. Where the flow is from more
than one direction, two or more standard
openings may be provided.
Higher
capacity openings larger than standard may
be provided but are of a special design.
(b) Grate Intake. The choice between inlets
with a round grate (Types GCP and GMP)
and those with a rectangular grate (Type
G1) hinges largely on hydraulic efficiency.
In a waterway where the greatest depth of
flow is at the center, both grates are equally
effective. In a waterway where the cross
slope concentrates the flow on one side of
the grate, the rectangular shape is
preferred.
For rectangular grates, the
charts contained in HEC 22 can be used to
compute flow intercept. Round grates
(Type 36R) with 0.5 foot of depression
develop a capacity of 12 CFS to 15 CFS.

837.5 Local Depressions

(1) Purpose. A local depression is a paved hollow
in the waterway shaped to concentrate and
direct the flow into the intake opening and
increases the capacity of the inlet. In a gutter
bordered by a curb, it is called a gutter
depression.
(2) Requirements. Local depressions generally
consist of a paved apron or transition of a shape
which serves the purpose. Local depressions
should meet the following requirements:
(a) Valley Medians. In medians on a grade,
the depression should extend a minimum of
10 feet upstream, 6 feet downstream and
6 feet laterally, measured from the edge of
the opening. In a grade sag, the depression
should extend a minimum of 10 feet on all
sides.
No median local depression,
however should be allowed to encroach on
the shoulder area.
The normal depth of depression is 4 inches.
(b) Paved Gutter Flares. The local depression
which adjoins the outer edge of shoulder at
the entrance to overside downdrains and
spillways is labeled "paved gutter flare" on
Standard Plans D87-A and D87-D. The

HIGHWAY DESIGN MANUAL

830-17
March 7, 2014

flow line approaching the inlet is depressed

to increase capacity and minimize water
spread on the roadbed. Within a flare
length of 10 feet the gutter flow line is
depressed a minimum of 6 inches at the
inlet. Recommended flare lengths for
various gutter flow line depression depths
are given on the Standard Plans. When
conditions warrant, these flare lengths may
be exceeded.

(3) General Notes on Design. Except for traffic

safety reasons, a local depression is to be
provided at every inlet even though the
waterway is unpaved. Where the size of intake
opening is a question, a depression of
maximum depth should be considered before
deciding on a larger opening. For traffic
reasons, the gutter depression should be
omitted in driveways and median curb and
gutter installations.

Traffic safety should not be compromised

for hydraulic efficiency. Any change in the
shape of the paved gutter flare that will
result in a depression within the shoulder
area should not be made. The Type 2
entrance taper and paved gutter flare is
intended for use on divided highways
where gutter grades exceed 2 percent and
flow is in the opposite direction of traffic.

It is permissible to omit gutter depressions at

sump inlets where the width of flow does not
exceed design water spread.

(c) Roadside Gutter and Ditch Locations.

Regardless of type of intake, the opening of
a drop inlet in a roadside gutter or ditch
should be depressed from 4 inches to
6 inches below the flow line of the
waterway with 10 feet of paved transition
upstream.
(d) Curb and Gutter Depressions. This type of
depression is carefully proportioned in
length, width, depth, and shape. To best
preserve the design shape, construction
normally is of concrete.
Further
requirements for curb and gutter
depressions are:

Length - As shown on Standard Plan

D78.

Width - Normally 4 feet, but for wide

flows or a series of closely spaced
inlets, 6 feet is authorized.

Depth - Where traffic considerations

govern, the depth commonly used is
0.1 foot.
Use the maximum of
0.25 foot wherever feasible at locations
where the resulting curb height would
not be objectionable.

(e) Type of Pavement. Local depressions

outside the roadbed are usually surfaced
with asphalt concrete 0.15 foot thick.

Topic 838 - Storm Drains

838.1 General
The total drainage system which conveys runoff
from roadway areas to a positive outlet including
gutters, ditches, inlet structures, and pipe is
generally referred to as a storm drain system. In
urban areas a highway storm drain often augments
an existing or proposed local drainage plan and
should be compatible with the local storm drain
system.
This section covers the hydraulic design of the pipe
or enclosed conduit portion of a storm drain
system.

838.2 Design Criteria

To adequately estimate design storm discharges for
a storm drain system in urban areas involving street
flooding it may be necessary to route flows by
using hydrograph methods.
Hydrographs are
discussed under Index 816.5 and further
information on hydrograph methods may be found
in Chapters 6 and 7 of HDS No.2, Highway
Hydrology.

838.3 Hydraulic Design

Closed conduits should be designed for the full
flow condition. They may be allowed to operate
under pressure, provided the hydraulic gradient is
0.75 foot or more below the intake lip of any inlet
that may be affected. The energy gradient should
not rise above the lip of the intake. Allowances
should be made for energy losses at bends,
junctions and transitions.

830-18

HIGHWAY DESIGN MANUAL

March 7, 2014

To determine the lowest outlet elevation for

drainage systems which discharge into leveed
channels or bodies of water affected by tides,
consideration should be given to the possibilities of
backwater. The effect of storm surges (e.g., winds
and floods) should be considered in addition to the
predicted tide elevation.

Table 838.4
Minimum Pipe Diameter for
Storm Drain Systems
Type of Drain

Minimum
Diameter (in)

Trunk Drain

18

Trunk Laterals

15(1)

Inlet Laterals

15(1)

Normally, special studies will be required to

determine the minimum discharge elevation
consistent with the design discharge of the facility.

838.4 Standards
(1) Location and Alignment. Longitudinal storm
drains are not to be placed under the traveled
way of highways. Depending upon local
agency criteria, storm drains under the traveled
way of other streets and roads may be
acceptable. A manhole or specially designed
junction structure is usually provided at
changes in direction or grade and at locations
where two or more storm drains are joined.
Refer to Index 838.5 for further discussion on
manholes and junction structures.
(2) Pipe Diameter. The minimum pipe diameter to
be used is given in Table 838.4.
(3) Slope. The minimum longitudinal slope should
be such that when flowing half full, a self
cleaning velocity of 3 feet per second is
attained.
(4) Physical Properties.
In general, the
considerations which govern the selection of
culvert type apply to storm drain conduits.
Alternative types of materials, overfill tables
and other physical factors to be considered in
selecting storm drain conduit are discussed
under Chapter 850.
(5) Storage. In developing the most economical
installation, the designer should not overlook
economies obtainable through the use of
pipeline storage and, within allowable limits,
the ponding of water in gutters, medians and
interchange areas. Inlet capacity and spacing
largely control surface storage in gutters and
medians; inlet capacity governs in sump areas.

NOTE:
(1) 18 minimum if wholly or partly under the
roadbed.
Specific subjects for special consideration are:
*

Bedding and Backfill.

Bedding and
backfill consideration are discussed under
Index 829.2. Maximum height of cover
tables are included in Chapter 850 and
minimum thickness of cover is given in
Table 856.5.

Roughness Factor. The roughness factor,

Manning's n value, generally assumes
greater importance for storm drain design
than it does for culverts.
Suggested
Manning's n values for various types of
pipe materials are given in Table 852.1.

(6) Floating Trash.

Except at pumping
installations, every effort should be made to
carry all floating trash through the storm drain
system. Curb and wall opening inlets are well
suited for this purpose. In special cases where
it is necessary to exclude trash, as in pumping
installations, a standard trash rack must be
provided across all curb and wall openings of
tributary inlets. See the Standard Plans for
details.
(7) Median Flow. In estimating the quantity of
flow in the median, consideration should be
given to the effects of trash, weeds, and
plantings.

HIGHWAY DESIGN MANUAL

830-19
March 7, 2014

838.5 Appurtenant Structures

(1) Manholes.
(a) General Notes. The purpose of a manhole
is to provide access to a storm drain for
inspection and maintenance. Manholes are
usually constructed out of cast in place
concrete, pre-cast concrete, or corrugated
metal pipe. They are usually circular and
approximately three or four feet in
diameter to facilitate the movement of
maintenance personnel.
There is no Caltrans Standard Plan for
manholes. Relocation and reconstruction
of existing storm drain facilities, owned by
a city or county agency, is often necessary.
Generally the local agency has adopted
manhole design standard for use on their
facilities. Use of the manhole design
preferred by the responsible authority or
owner is appropriate.
Commercial precast manhole shafts are
effective and usually more economical than
cast in place shafts. Brick or block may
also be used, but only upon request and
justification from the local agency or
owner.
(b) Location. Following are common locations
for manholes:

Where two or more drains join,

At locations and spacing

facilitate maintenance,

Where the drain changes in size,

At sharp curves or angle points in

excess of 10 degrees,

Points where an abrupt flattening of the

grade occurs, and

On the smaller drains, at

downstream end of a sharp curve.

which

the

Manholes are not required if the conduit is

large enough to accommodate a man,
unless spacing criteria govern. Manholes
should not be placed within the traveled
way. Exceptions are frontage roads and
city streets, but intersection locations
should be avoided.

(c) Spacing. In general, the larger the storm

drain, the greater the manhole spacing. For
pipe diameter of 48 inches or more, or
other shapes of equal cross sectional area,
the manhole spacing ranges from 700 feet
to 1200 feet. For diameters of less than
48 inches, the spacing may vary from
300 feet to 700 feet. In the case of small
drains where self-cleaning velocities are
unobtainable, the 300 feet spacing should
be used. With self-cleaning velocities and
alignments without sharp curves, the
distance between manholes should be in
the upper range of the above limits.
(d) Access Shaft.
For drains less than
48 inches in diameter, the access shaft is to
be centered over the drain. When the drain
diameter exceeds the shaft diameter, the
shaft should be offset and made tangent to
one side of the pipe for better location of
the manhole steps. For drains 48 inches or
more in diameter, where laterals enter from
both sides of the manhole, the offset should
be toward the side of the smaller lateral.
See Standard Plan D93A for riser
connection details.
(e) Arrangement of Laterals.
To avoid
unnecessary head losses, the flow from
laterals which discharge opposite each
other should converge at an angle in the
direction of flow. If conservation of head
is critical, a training wall should be
provided.
(2) Junction Structures. A junction structure is an
underground chamber used to join two or more
conduits, but does not provide direct access
from the surface. It is designed to prevent
turbulence in the flow by providing a smooth
transition. This type of structure is usually
needed only where the trunk drain is 42 inches
or more in diameter. A standard detail sheet of
a junction structure is available for pipes
ranging from 42 inches to 84 inches in
diameter at the following Office Engineer web
site
address:
http://www.dot.ca.gov/hq/esc/structures_cadd/XS_s
heets/Metric/dgn/. The XS sheet reference is XS

4-26. Where required by spacing criteria, a

manhole should be used.

830-20

HIGHWAY DESIGN MANUAL

March 7, 2014

(3) Flap Gates.

When necessary, backflow
protection should be provided in the form of
flap gates.
These gates offer negligible
resistance to the release of water from the
system and their effect upon the hydraulics of
the system may be neglected.
If the outlet is subject to floating debris, a
shelter should be provided to prevent the debris
from clogging the flap gate. Where the failure
of a flap gate to close would cause serious
damage, a manually controlled gate in series
should be considered for emergencies.

Topic 839 - Pumping Stations

839.1 General
Drainage disposal by pumping should be avoided
where gravity drainage is reasonable. Because
pumping installations have high initial cost,
maintenance expense, power costs, and the
possibility of failure during a storm, large
expenditures can be justified for gravity drainage.
In some cases, this can be accomplished with long
runs of pipe or continuing the depressed grade to a
natural low area.
Whenever possible, drainage originating outside
the depressed areas should be excluded. District
and Division of Structures cooperation is essential
in the design of pumping stations, tributary storm
drains, and outfall facilities. This is particularly
true of submerged outlets, outlets operating under
pressure, and outlets of unusual length.

839.2 Pump Type

Horizontal pumps in a dry location are generally
specified for ease of access, safety, and
standardization of replacement parts.
Only in special cases is stand-by power for
pumping plants a viable consideration.
All
proposals for stand-by power are to be reviewed by
and coordinated with the Division of Structures.

839.3 Design Responsibilities

When a pumping station is required, responsibility
for design between the District and the Division of
Structures is as follows:
(1) Districts. The District designs the collector
and the outfall facilities leading from the

chamber into which the pumps discharge. This

applies to outfalls operating under gravity and
with a free outlet. Refer to Topic 838.
Details of pumping stations supportive
information to be submitted by the District to
the Division of Structures is covered under
Index 805.8 and Chapter 3-3.1(4) of the
Drafting and Plans Manual.
(2) Division of Structures.
The Division of
Structures will prepare the design and contract
plans for the pumping station, the storage box
and appurtenant equipment, considering the
data and recommendations submitted by the
District.
The Division of Structures will furnish the
District a preliminary plan based on data
previously submitted by the District. It will
show the work to be covered by the Division of
Structures plans, including a specific location
for the pumping plant and storage box, the
average and maximum pumping rates and the
power required.

839.4 Trash and Debris Considerations

Storm drain systems leading to pumping plants are
to be designed to limit the inflow of trash and
debris, as these may cause damage to the pump
impellers and create a maintenance removal
nuisance. Standard grate designs are effective at
ensuring that trash and debris are screened out of
the inflow, but where side opening or curb opening
inlets are constructed, trash racks must be added to
the inlet design. The only Standard Plan detail for
curb opening designs is shown on Standard Plan
D74B and is used in conjunction with Type GDO
inlets. On those occasions where pipe risers with
side opening inlets are part of the system, refer to
Standard Plan D93C for appropriate trash rack
design details.

839.5 Maintenance Consideration

Access to the pumping plant location for both
maintenance personnel and maintenance vehicles is
generally provided by way of paved access road or
city street. One parking space minimum is to be
provided in the vicinity of the pumping plant. An
area light is generally provided when it is
determined that neither the highway lighting nor
the street lighting is adequate. Access to the

HIGHWAY DESIGN MANUAL

830-21
March 7, 2014

pumping plant for maintenance from the top of the

cut slope generally consists of a stairway located
adjacent to the pumping plant. The stairway
generally extends from the top of cut slope to the
toe of cut slope. Access to the pump control room
should be through a vertical doorway with the
bottom above flood level, and never through a
hatch.

839.6 Groundwater Considerations

As the lowest point in the storm drain system,
pumping plants are particularly susceptible to
problems associated with rises in groundwater
tables. Where the foundation of pump houses or
associated storage boxes are at an elevation where
they would be subjected to existing or future
groundwater tables, sealing around the base of the
foundation is necessary. The use of bentonite or
other impervious material is typically sufficient in
keeping groundwater from welling up through the
relatively pervious structure backfill.
Sealing requirements will typically be specified by
the Division of Structures during the pump plant
design. However, the district should provide any
information relative to historical groundwater
levels or fluctuations which would be of
importance, or known plans by local or regional
water districts to modify recharge patterns in a
manner that could impact the design.