DIOTEC ELECTRONICS CORPORATION

PRODUCT GUIDE

TRUE VOID FREE

VACUUM DIE SOLDERING

SOFT GLASS DIODES

HIGH VOLTAGE

ULTRA FAST RECOVERY

DISH
DIODES

TVS
PRESS
FIT

WEB SITE: www.diotec-usa.com

E-MAIL: [email protected]

DIOTEC ELECTRONICS CORP.

THE RECTIFIER SPECIALISTS

THE ONLY QUALITY

DIODES AND RECTIFIERS
AT COMPETITIVE PRICES

18020 HOBART BLVD, UNIT B GARDENA, CALIFORNIA 90248 USA

TEL: 310 - 767 - 1052 FAX: 310 - 767 - 7958
EMAIL: [email protected] WEB SITE: www.diotec-usa.com

DIOTEC ELECTRONICS CORPORATION

18020 HOBART BLVD.
GARDENA, CA 90248 USA
PH: 310-767-1052 FX: 310-767-7958 E-MAIL: [email protected]

WEB SITE: www.diotec-usa.com

EVER WONDER WHY SOME DIODES DIE PREMATURELY

.. WITHOUT OBVIOUS CAUSE
Most Likely It's The Invisible Killer .. DIE ATTACH SOLDER VOIDS
This invisible problem is much, much, more serious, and a lot more common than you might think. In the photographs below,
diodes produced by a prestigious multinational semiconductor manufacturer were examined for die solder quality. These
diodes were provided by one of our potential customers who have experienced serious quality problems and premature
failures.
This set of photos illustrates a very common situation when a diode is pried open

LARGE VOID AREA REVEALED IN

THE SOLDER LAYER

SECTION B
SECTION A
NUMEROUS SOLDER VOIDS CAN CLEARLY BE SEEN IN THESE CLOSE
UPS. These Voids 1) Greatly Weaken The Diode's Mechanical Integrity, 2)
Increase The Forward Voltage Drop, and 3) Severely Restrict The Dissipation of
Heat From The Die. Restricted Heat Dissipation causes the Diode to Operate at
Elevated Temperatures Which Could Lower Its Current Handling and/or Cause
Premature Failure.

This set of photographs illustrates another common, but much more serious, situation. Here the diode is pried open and
separates completely at the die solder layer

ONLY SOLDER IN SECTION B

CHIP IS INTACT IN SECTION A
SOLDER COVERS ~ 50% OF DIE

SECTION B - ONLY SOLDER

SECTION A- DIE SIDE
The Solder Either Failed to Wet And, Hence, Bond to The Die's Surface (Surface
Outlined in Red on Section B) or is riddled with voids. As a Result, This Diode
Has Absolutely No Mechanical Strength And May Fail On Impact if dropped or
Struck. Additionally, The Thermal Resistance of This Diode is so High that
Thermal Runaway is a Certainty.

See The DIOTEC Difference - VOID FREE DIE SOLDERING.

Copyright 2001 DIOTEC Electronics Corporation. All rights reserved

DIOTEC ELECTRONICS CORPORATION

This is the DIOTEC difference.

BREAKS AT SILICON DIE

NO VISIBLE VOIDS.

SECTION A
SECTION B
Superior Soldering Results in SUPERIOR MECHANICAL STRENGTH, SUPERB
HEAT DISSIPATION, and LOWER FORWARD VOLTAGE DROP

DIOTEC utilizes an advanced, computer controlled, vacuum die soldering process, which enables silicon chips to be soldered
to metal with exceptional consistency and void free quality. Thus, DIOTEC diodes and bridge rectifiers have
unmatched heat dissipation, cooler junction temperatures, lower leakage currents, and reduced thermal stress. Additionally,
the high quality die attachment allows the diodes survive mechanical shock without bond failure, another common problem
with most offshore "cheap" diodes.

SHOULD YOU WANT:

Want to discuss this topic further?

A free analysis similar to that shown here to determine the
quality of the diodes you are now using? We'll tell it like we see it
and return your items with the pictures so you can see for
yourself.
Wish to put us to the test in your environment? Request product
samples
Please don't hesitate to contact:
JOE LIN or DEAN LIGOCKI
PH: 310-767-1052
FX: 310-767-7958
[email protected]
[email protected]

DIOTEC ELECTRONICS CORPORATION

THE ONLY HIGH QUALITY DIODES & RECTIFIERS AT COMPETITIVE PRICES

Copyright 2001 DIOTEC Electronics Corporation. All rights reserved

DIOTEC ELECTRONICS CORP.

18020 Hobart Blvd., Unit B
Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

DIOTEC Electronics Corp. is a major manufacturer of power diodes and rectifiers, with facilities and representatives
worldwide. Principle engineering, sales, technical, and administrative personnel are located at DIOTEC's headquarters
in Gardena, California, 20 miles south of the Los Angeles International airport. Major laboratory, test, and manufacturing
facilities are located in Penang, Malaysia, and Carson, California USA.
DIOTEC was established to fill a severe industry need for a reliable and dependable manufacturer who:
Could offer comprehensive, high quality diode/rectifier product lines at very competitive prices
Is capable, flexible, and willing to provide prompt technical and professional assistance to its customers
Has an adequate inventory near its customers to support their production requirements at all times.
In its 15 year history, DIOTEC and its affiliate company have grown from a star-up company to one with over $12 million
in worldwide sales. Initially, DIOTEC's product line was limited to general purpose axial lead silicon diodes. Today,
DIOTEC offers Schottky Barrier diodes, Super Efficient and Ultra-Fast Recovery diodes, a significantly expanded line of
General Purpose and Fast Recovery diodes, and the most comprehensive line of Full Wave Bridge Rectifiers.
DIOTEC provides its customers with diodes and rectifiers of superior quality at competitive prices. This superior quality
results from using advanced, computer controlled, vacuum die soldering process which enables silicon chips to be
soldered to metal with exceptional consistency and void free quality. Thus, DIOTEC diodes and bridge rectifiers have
unmatched heat dissipation, cooler junction temperature, lower leakage currents, and reduced thermal stress.
Additionally, the high quality die attachment allows the diodes to survive mechanical shock without bond failure, another
common problem with most offshore "cheap" diodes.
DIOTEC has also introduced the industry's only "Soft Glass Diode". These diodes exhibit unmatched mechanical and
thermal resistance properties. Additional information on "Soft Glass may be found in Appendix IX.
DIOTEC has 7 main product lines:
Automotive Diodes (TVS & Standard - 12 to 75 amp)
Full Wave Bridge Rectifiers (1 to 50 amp, 50 - 1000 Volt)
Super Efficient and Ultra-Fast Recovery Diodes Fast Recovery Diodes
Schottky Barrier Rectifiers
Fast Recovery Full Wave Bridge Rectifiers
General Purpose Diodes
High Voltage Diodes
VISIT US ON THE WEB for the latest product and specification updates
DIOTEC's web site is located at:

www.diotec-usa.com

Our general e-mail address is:

[email protected]

Take some time every once in a while to visit our web site. Our product lines/specifications are continually being
reviewed and updated based on customer requirements, product design improvements, and quality testing. When
considering one of our products for a specific application, always check the web site to ensure you have the latest
specifications.
When USING THIS CATALOG, please keep in mind that every effort has been made to ensure that the information
contained here is current, accurate, and of the necessary detail to support the component or design engineer. It is
recognized that a standard product can not satisfy every application requirement. If your requirements fall in this
category, do not hesitate to call, fax or e-mail our technical staff. We are here to help you!
iii

DIOTEC ELECTRONICS CORP.

18020 Hobart Blvd., Unit B
Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

DIOTEC is dedicated to furnishing the highest quality products at the most competitive cost. Thus, product changes to
improve reliability, function, and design may be made without notice. The information in this data book has been
carefully reviewed and is believed to be accurate. However, no responsibility is assumed for inaccuracies. Before
committing to a design, it is recommended that the designer request product samples (See Appendix IX) to validate the
operational characteristics and performance in the actual application.
DIOTEC does not imply any warranty, or assume any liability from the application or use of any product or circuit
described in this catalog. DIOTEC does not recommend the use of its products in applications where a
failure/malfunction of the product may directly threaten life or injury. The user of DIOTEC's products in life support
application assumes all risks of such use and indemnifies DIOTEC against all damages.
Following this introduction and table of contents, selector guides are provided for DIOTEC's Schottky Rectifiers, Super
Efficient/Ultra Fast Diode, Bridge Rectifier, General Purpose Diode, and Fast Recovery Diode product lines. Industry
cross-references are provided in the appendices to assist in the selection of the proper DIOTEC product for your
application.

iv

GENERAL
EVER WONDER WHY ...
INTRODUCTION
CONTENTS
SCHOTTKY RECTIFIER QUICK SELECTION GUIDE
SUPER EFFICIENT and ULTRA FAST RECOVERY DIODE QUICK SELECTION GUIDE
FULL WAVE BRIDGE RECTIFIER QUICK SELECTION GUIDE .
FAST RECOVERY BRIDGE RECTIFIER SELECTION GUIDE
GENERAL PURPOSE DIODE QUICK SELECTION GUIDE .
FAST RECOVERY DIODE QUICK SELECTION GUIDE

3-4
5-6
7
8
9
10-11
12
13
14

SCHOTTKY RECTIFIERS
Single Chip (1 to 30 Amp) .. 15-33 (Section A)
Center-Tap Dual Chip (12 to 60 Amp) . 34-46 (Section B)

SUPER EFFICIENT and ULTRA FAST RECOVERY DIODES

Single Chip (1 to 15 Amp) .. 47-73 (Section C)
Center-Tap Dual Chip (6 to 30 Amp) 74-84 (Section D)

FULL WAVE BRIDGE RECTIFIERS . 85-138 (Section E & F)

FAST RECOVERY FULL WAVE BRIDGE RECTIFIERS . 139-148 (Section G)
GENERAL PURPOSE and FAST RECOVERY DIODES . 149-184 (Section H)
HIGH VOLTAGE DIODES 185-189 (Section I)
AUTOMOTIVE DIODES
Transient Voltage Suppressors 190-202 (Section J)
Standard Diodes .. 203-217 (Section K)

APPENDICES
Appendix I
Appendix II
Appendix III
Appendix IV
Appendix V
Appendix VI
Appendix VII
Appendix VIII
Appendix IX

Packaging Information
Schottky Barrier Rectifier Cross Reference .
Super Efficient And Ultra Fast Recovery Diode Cross Reference .
Standard And Fast Recovery Bridge Rectifier Cross Reference ..
General Purpose And Fast Recovery Diode Cross Reference ..
Acronyms And Abbreviations .
Alpha-Numeric Product List .
Sample Request Form
Soft Glass ..

219
220
221-222
223-225
226-227
228
229
230-231
232

v
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

SCHOTTKY RECTIFIER QUICK SELECTION GUIDE - SEE SECTIONS A and B

DIOTEC Schottky Barrier Rectifiers feature a metal semiconductor junction with guard ring, epitaxial construction, low forward
voltage drop, high current capability, and molded plastic material with an U/L 94V-O flammability rating. These products are ideal
for use in low voltage, high frequency power supplies, as very fast clamping diodes, free wheeling, and polarity protection
applications. These devices feature switching times of less than 10nS and are offered in current ranges up to 60 Amperes and
reverse voltages to 100 volts.
IO , AVERAGE RECTIFIED FORWARD CURRENT (AMPERES)
1

DO-41

DO-27

12

16

Dual Diode*

1N5817

30

1N5818

40

1N5819

SK102

1N5820

SK302

SK502

SK304

SK504

Dual Diode*

Dual Diode*

1N5821
SK104

1N5822

40

60

TO-220AC TO-220AC TO-220AB TO-247AC TO-220AB TO-247AB TO-247AC TO-247AB TO-247AB TO-247AB
TO-3P
TO-3P
TO-3P
TO-3P
TO-3P
TO-3P
(FullyInsulated)
(FullyInsulated)
(FullyInsulated) (FullyInsulated)

DO-27

VRRM
20

30

24

50

Dual Diode*

Dual Diode*

Dual Diode*

30SK30

SK6030C

6SK40

12SK40

SK1240C

16SK40

SK1640C SK2440C

30SK40

SK3040C SK4040C SK6040C

6SK50

12SK50

SK1250C

16SK50

SK1650C SK2450C

30SK50

SK3050C SK4050C SK6050C

60

SK106

SK306

SK506

6SK60

12SK60

SK1260C

16SK60

SK1660C SK2460C

30SK60

SK3060C SK4060C SK6060C

70

SK107

SK307

SK507

6SK70

12SK70

SK1270C

16SK70

SK1670C SK2470C

30SK70

SK3070C SK4070C SK6070C

80

SK108

100

SK110

SK310

SK510

6SK100

12SK100 SK12100C 16SK100 SK16100C SK24100C

IFSM
(Amps)**

25

40

80

120

150

TL @ Rated IO*
(oC)

90

90

90

90

90

TJ (Max)
(oC)

125

150

125

150

VFM @ IFM = IO
o
( TX = 25 C)***

0.6

0.8

0.525

0.8

TC @ Rated IO*
(oC)

120

180

120

SK30100C SK40100C

240

160

200

600

300

350

600

100

110

100

100

90

85

90

100

100

150

150

150

150

150

150

150

150

150

0.85

0.85

0.85

0.85

0.85

0.7

0.85

0.92

0.65

* I O IS TOTAL DEVICE OUTPUT

** REPRESENTS THEMAX.FORALLPRODUCTSLISTED
SOMEINDIVUAL DEVICESMAY EXHIBITALOWERI FSM . DETAILEDDATA SHEETS ARE AVAILABLE UPONREQUEST.
*** TX = TL FORDO-41/27PACKAGEDPRODUCTS; TX = TC FOR TO-220/247 PACKAGED PRODUCTS.

PART NUMBERING SYSTEM

(1) AXIAL LEAD PRODUCTS (SEE SECTION A)
Example: SK102 (1 Amp, 20 Volt, Axial Lead Schottky)

SK A VV
Blocking Voltage Reference (20 - 100 Volts) - 2 Digits. Examples: 02 = 20 Volts; 10 = 100 Volts
Current Reference (Average Forward Rectifed Current) - 1 Digit.
Schottky Diode Designator

(2) TWO (2) PIN TO-22OAC AND TO-247AC PACKAGED PRODUCTS (SEE SECTION A)
Examples: 6SK60 (6 Amp, 60 Volt, 2- Pin TO Packaged Schottky Diode)
12SK100 (12 Amp, 100 Volt, 2-Pin TO Packaged Schottky Diode)

A(A) SK VV(V)
Blocking Voltage Reference (30 - 100 Volts) - 2 or (3) Digits.
Schottky Diode Designator
Current Reference (Average Forward Rectifed Current) - 1 or (2) Digits. Range: 6 - 30 Amps

(3) THREE ( 3) PIN TO-22OAB AND TO-247AB PACKAGED PRODUCTS (SEE SECTION B)
Example: SK1250C (12 Amp, 50 Volt, 3-Pin TO Packaged Schottky Diode)

SK AA VV C
Dual Diode Common Point Designator (C=Common Cathode; A=Common Anode)
Blocking Voltage Reference (30 - 100 Volts) - 2 Digits.
Current Reference (Average Forward Rectifed Current) - 2 Digits. Range 12 - 60 Amps.
Schottky Diode Designator.

vi
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

SUPER EFFICIENT/ULTRAFAST RECOVERY RECTIFIER

QUICK SELECTION GUIDE - SEE SECTIONS C and D
These products complement DIOTEC's Schottky product line by providing switching times in the 30 to 90 nS range. All TO-220/247
devices are supplied with the cathodes connected to the "backside" metal heatsink. Reverse polarity devices (i.e., common anode)
may be available upon special request. Switching power supplies operating from 20 kHz to 250 kHz, inverters, and freewheeling
diodes are excellent applications for these devices.
IO, AVERAGE RECTIFIED FORWARD CURRENT (AMPERES)
1

DO-41

10

12

15

16

30

DO-27
G-6A

TO-220AC TO-220AB TO-220AC TO-220AC

DualDiode*

TO-220AB
Dual Diode*

TO-220AC TO-220AC TO-220AB TO-220AB TO-247AB

TO-3P
DualDiode*
DualDiode*

Dual Diode*

SOFT GLASS DIODES

VRRM

SOFT GLASS DIODES

Fully
Insulated

50

UFR100

SPR30

UFR300

UFR400

100

UFR101

SPR11

SPR21

SPR31

UFR301

UFR401

SPR51

200

UFR102

SPR12

SPR22

SPR32

UFR302

UFR402

300

UFR103

SPR13

SPR23

SPR33

UFR303

UFR403

400

UFR104

SPR14

SPR24

SPR34

UFR304

UFR404

500

UFR105

UFR305

UFR405

600

UFR106

SPR26

UFR306

UFR406

UFR606

SPR28

UFR308

UFR408

UFR608

UFR310

UFR410

150

150

800

UFR108

1000

UFR110

IFSM
(Amps)**

35

40

50,70

75

Fully
Insulated

Fully
Insulated

NonInsulated

Fully
Insulated

Fully
Insulated

UFR600

NonInsulated

Fully
Insulated

NonInsulated

Fully
Insulated

SPR150

UFR601

6SPR01 SPR601C 8SPR01

SPR81

SPR1001C 12SPR01 SPR151 SPR1601C SPR161C UFR3001C

SPR52

UFR602

6SPR02 SPR602C 8SPR02

SPR82

SPR1002C 12SPR02 SPR152 SPR1602C SPR162C UFR3002C

SPR53

UFR603

6SPR03 SPR603C 8SPR03

SPR83

SPR1003C 12SPR03 SPR153 SPR1603C SPR163C UFR3003C

SPR54

UFR604

6SPR04 SPR604C 8SPR04

SPR84

SPR1004C 12SPR04 SPR154 SPR1604C SPR164C UFR3004C

UFR605

6SPR05 SPR605C 8SPR05

SPR85

SPR1005C 12SPR05 SPR155 SPR1605C SPR165C UFR3005C

150

SPR86

300

TC @ Rated IO
(o C)

SPR156

SPR166C

80

60

120

125

100

120

250

150

200

250

100

120

110

110

120

110

110

100

100

100

TA @ Rated IO
(oC)**

55

55

55

55

55

80,40,
35

55

55

TJ (Max)
(oC)

150

150

150

150

150

150

150

150

150

150

150

150

150

150

150

150

150

150

TRR
(nS)**

50,75

35

35,50,
75

35

50,75

50,75

50

60,75,
90

50,75

30

35,45

35,45

35,45

35,45

35,50

35,45

35,50

50,60

* I O IS TOTAL DEVICE OUTPUT

** TWO OR MOREENTRIES INDICATES A DIFFERENCE IN PARAMETER VALUES AMONG THE SPECIFIC PRODUCTS IN THE SERIES LISTED.

PART NUMBERING SYSTEM

AXIAL LEAD PRODUCTS (SEE SECTION C)
(a) Example: SPR21 (2 Amp, 100 Volt Axial Lead Super Efficient Rectifier)

(b) Example: UFR302 (3 Amp, 200 Volt, Axial Lead, Ultrafast Rectifier)

SPR/UFR A V

UFR A VV
Blocking Voltage Reference (50 - 800 Volts) - 1 Digit
Examples: 1 = 100 Volts; 8 = 800 Volts
Current Reference (Ave. Forward Rectified Current) - 1 Digit.

Blocking Voltage Reference (50 - 1000 Volts) - 2 Digits.

Examples: 00 = 50 Volts; 10 = 1000 Volts
Current Reference (Ave. Forward Rectified Current) - 1 Digit.
Ultrafast Rectifier Designator.

Rectifier Type Designator

SPR = Super Efficient Rectifier/UFR = Ultrafast Rectifier.

TWO (2) PIN TO-22OAC PACKAGED PRODUCTS (SEE SECTION C)

a) Example: 12SPR01 (12 Amp, 100 Volt, 2- Pin, FULLY INSULATED, Super Efficient Rectifier)

(b) Example: SPR85 (8 Amp, 500 Volt, 2-Pin, NON-INSULATED, Super Efficient Rectifier)

SPR A(A) V

A(A) SPR VV
Blocking Voltage Reference (100 - 500 Volts) - 2 Digits.
Examples: 01 = 100 Volts, 05 = 500 Volts

Blocking Voltage Reference (50 - 600 Volts) - 1 Digit.

Examples: 0 = 50 Volts; 6 = 600 Volts.
Current Reference (Average Forward Rectified Current)
1 or 2 Digits - Range: 8 to 15 Amps.
Super Efficient Rectifier Designator.

Super Efficent Rectifier Designator

Current Reference (Average Forward Rectified Current) - 1 or (2) Digits.
Range: 8 - 12 Amps

THREE (3) PIN TO-22OAB AND TO-247AB PACKAGED PRODUCTS (SEE SECTION D)
(a) Example: SPR605C (6 Amp, 500 Volt, 3-Pin FULLY INSULATED Super Efficient Rectifier)

(b) Example: SPR163C (16 Amp, 300 Volt, 3-Pin NON- INSULATED Super Efficient Rectifier)

SPR/UFR A(A) 0 V C

SPR AA V C
Dual Diode Common Designator (C=Common Cathode; A=Common Anode)
Blocking Voltage Reference (100 - 600 Volts) - 1 Digit.
Key to Denote Fully Insulated Rectifier

Dual Diode Common Designator

(C=Common Cathode; A=Common Anode)
Blocking Voltage Reference (100 - 600 Volts) - 1 Digit.
Current Reference (Average Forward Rectified Current)
2 Digits. Range 15 - 16 Amps
Super Efficient Rectifier Designator

Current Reference (Average Forward Rectified Current) - 1 or 2 Digits.

Range 6 - 30 Amps.
Rectifier Type Designator: SPR=Super Efficient Rectifier/UFR=Ultrafast Rectifier.

vii
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

SILICON BRIDGE RECTIFIER QUICK SELECTION GUIDE - SEE SECTION E

DIOTEC offers a complete line of single phase full wave bridge rectifiers. A wide variety of package designs allows these bridges to
be used in virtually any application. Forward current outputs range from 1 to 50 Amps with reverse voltages from 50 to 1000 Volts.
IO, AVERAGE RECTIFIED FORWARD CURRENT (AMPERES) - Note 1
1.5

1
DT

+
S1NB
60 46

DI104

3
DT
SB200

4
DT
SB404L

DIOTEC
KBLO8

AC

10

SB506
712
_

AC

VRRM
50

DI100

S1NB05

WB100

WB150

WB200

SB200

DB300

SB400L

KBL00

SB401L

KBL01

SBU4B

SB402L

KBL02

SBU4D

100

DI101

S1NB10

WB101

WB151

WB201

SB201

DB301

200

DI102

S1NB20

WB102

WB152

WB202

SB202

DB302

SBU4A

SB500

SBU6A

DB600

HBU600

SBU8A

DB800

DB1000

SB501

SBU6B

DB601

HBU601

SBU8B

DB801

DB1001

SB502

SBU6D

DB602

HBU602

SBU8D

DB802

DB1002

DB804
ADB804

DB1004
ADB1004

SBU4G

SB504

DB604 HBU604
SBU6G ADB604 AHBU604 SBU8G

400

DI104

S1NB40

WB104

WB154

WB204

SB204

DB304
SB404L
ADB304 ASB404L KBL04

600

DI106

S1NB60

WB106

WB156

WB206

SB206

DB306 SB406L
ADB306 ASB406L KBL06

SBU4J

SB506

DB606 HBU606
SBU6J ADB606 AHBU606 SBU8J

DB806
ADB806

DB1006
ADB1006

800

DI108

S1NB80

WB108

WB158

WB208

SB208

DB308
SB408L KBL08
ADB308 ASB408L

SBU4K

SB508

SBU6K

DB608 HBU608 SBU8K

ADB606 AHBU606

DB808
ADB806

DB1008
ADB1006

1000

DI110

S1NB100

WB110

WB1510

WB210

SB210

DB310

SB410L

KBL10

SBU4M

SB510

SBU6M

DB610

HBU610

SBU8M

DB810

DB1010

Typ. RJA

40

40

40

35

35

30

12

19.0

19.0

19.0

17.0

16.0

16.0

16.0

16

12

12

Typ. RJL

15

15

15

15

15

11

3.4

3.4

3.4

3.3

3.1
5.7

5.7

100
65

55

100
40

50
40

50
40

100
65

100
50

100
50

Typ. RJC

TC @ Rated IO (oC)
TA @ Rated IO (oC)
(Note 2)

40

40

50

25

25

55

60
25

50

100
65

Max. VF

1.10

1.05

1.00

1.00

1.00

1.05

0.95

0.95

0.95

0.95

1.00

0.95

0.95

0.95

0.95

0.95

0.95

0.90

0.90

0.90

0.90

0.95

0.90

0.90

0.90

0.90

0.90

0.90

150

150

150

150

150

150

150

150

150

150

150

Note 3
Note 4

Note 3
Note 4

Note 3
Note 4

Note 3
Note 4

Typ. VF
TJ (Max)
(oC)

150

150

150

150

150

150

Avalanche Voltages

V(BR)Min
V(BR)Max

Note 3
Note 4

NOTES: (1) IO is Total Bridge Output

(2) Tc - With BridgeMountedonanAluminum Plate; TA - With Bridge Mounted on PC Board (See DataSheets For Details)
(3) V (BR)MIN =450 Volts For All 400 Volt ControlledAvalanche Bridges (i.e., Those Bridges WithaPartNumberBeginningWithThe Letter "A")
(3) V (BR)MIN = 650 VoltsFor All 600 Volt Controlled Avalanche Bridges
(3) V (BR)MIN = 850 VoltsFor All 800 Volt Controlled Avalanche Bridges
(4) V (BR)MAX=900 Volts For All400VoltControlled Avalanche Bridges
1100 Volts For All600VoltControlled Avalanche Bridges
1300 Volts For All800VoltControlled Avalanche Bridges
BODY ID

PART NUMBERING SYSTEM

1 TO 10 AMP BRIDGES
(a) Example: DB600 or HBU606 (6 Amp, 50 Volt, or 6 Amp, 600 Volt in Rectangular or Special Package)

DB
DI
HBU
SB
S1NB
SBU
SDB
SDI
WB

DEFINITION

Retangular Package, Small Vertical Elevation

DualIn-Line 4 Pin Package
Special Package,IdealForMotor Applications
Vertical or Side-Looking Package
DualIn-Line 4 Pin Package
Side-Looking Package w/Center Mounting Hole
Side Looking DB Package
DualIn-Line 4 Pin Package
Cylindrical Package

(A) BB(B) C(C) VV

Blocking Voltage Reference (50 - 1000 Volts) - 2 Digits, e.g., 00 = 50 Volts; 02 = 200 Volts, 10 = 1000 Volts.
Current Reference (Average Forward Rectifed Current For Total Bridge) - 1 or 2 Digits.
Body Type Designator. Two or 3 Letters - See Table at Right.
The Letter "A" Before the Body Designators SB, DB, or HBU Indicates Bridge is Part of the "Avalanche" Series
Note: The SB400/ASB400 Series Part Numbers Incorporate a Suffix Letter (L) to Indicate the "+" Output of the Rectifier is on The Longest Lead.
The New Bridge Series, S1NBVV(V), Incorporates the 1 Amp Current Reference in the Body Designator and Uses the Final 2 or 3 Digits as a Voltage
Reference, i.e., 05 = 50 Volts, 10 = 100 Volts, 100 = 1000 Volts
(b) Example: SBU6A (6 Amp, 50 Bridge Rectifier, Side Looking Package)

SBU C L
Blocking Voltage Reference (50 - 1000 Volts) - 1 Letter. A, B, D, G, J, K, M = 50, 100, 200, 400, 600, 800, 1000 Volts, Respectively.
Current Reference (Average Forward Rectifed Current) - 1 Digit, Range 4-8 Amps.
Side Looking Package With Mounting Hole

15 - 50 AMP BRIDGES
Example: DB3504 or ADB3504P (35 Amp, 400 Volt Bridges. The Second Bridge is One of The "Avalanche" Series and Provided in a Plastic Package, i.e., With Integrally Molded Heat Sink)

(A) (S)DB AA VV (P)/ (W) or (T)

Suffix Indicating Wire (W) or Fast-on Terminals (T)
When Present, Indicates Plastic Package With The Heat Sink Integrated into The Bridge Encapsulation (See Figure 2 on Facing Page)
Blocking Voltage Reference (50 - 1000 Volts) - 2 Digits, e.g., 00 = 50 Volts, 05 = 500 Volts, 10 = 1000 Volts
Current Reference (Average Forward Rectifed Current) - 2 Digits, Range: 15 - 50 Amps
Body Type Designator. Rectangular (DB) Body Used in These Products. When "S" is Present, Indicates Side-Looking (In-Line) Package
The Letter "A" Before the Body Designator, DB, Indicates Bridge is Part of the "Avalanche" Series

viii
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

SILICON BRIDGE RECTIFIER QUICK SELECTION GUIDE (Continued)

SEE SECTION E
DIOTEC's 15, 25, and 35 Amp Bridges are offered with an electrically isolated metal case or epoxy case with integral heatsink,
Figures 1 and 2, respectively. The metal or epoxy case, in turn, can be obtained with Fast-On Terminals or Wire Leads. DIOTEC
offers 40 and 50 Amp in-line bridges also. These in-line bridges are only available in the epoxy case with wire leads. The 50 Amp
bridge is also available in the epoxy case with Fast-On Terminals or Wire Leads.
IO, AVERAGE RECTIFIED FORWARD CURRENT (AMPERES)
35

25

15

40

50

SEE FIG 1

SEE FIG 2

SEE FIG 1

SEE FIG 2

SEE FIG 1

SEE FIG 2

SEE FIG 3

SEE FIG 3

SEE FIG 2

BELOW

BELOW

BELOW

BELOW

BELOW

BELOW

BELOW

BELOW

BELOW

VRRM
50

DB1500

DB1500P

DB2500

DB2500P

DB3500

DB3500P

SDB4000

SDB5000

DB5000P

100

DB1501

DB1501P

DB2501

DB2501P

DB3501

DB3501P

SDB4001

SDB5001

DB5001P

200

DB1502

DB1502P

DB2502

DB2502P

DB3502

DB3502P

SDB4002

SDB5002

DB5002P

400

ADB1504

DB1504

ADB1504P DB1504P

ADB2504

DB2504

ADB2504P DB2504P

ADB3504

DB3504

ADB3504P

DB3504P

SDB4004

SDB5004

ADB5004P DB5004P

600

ADB1506

DB1506

ADB1506P DB1506P

ADB2506

DB2506

ADB2506P DB2506P

ADB3506

DB3506

ADB3506P

DB3506P

SDB4006

SDB5006

ADB5006P DB5006P

800

ADB1508

DB1508

ADB1508P DB1508P

ADB2508

DB2508

ADB2508P DB2508P

ADB3508

DB3508

ADB3508P

DB3508P

SDB4008

SDB5008

ADB5008P DB5008P

DB1510

DB1510P

DB2510

DB2510P

DB3510P

SDB4010

SDB5010

DB5010P

1000

RJC

DB3510

1.8

1.4

1.6

1.2

1.6

1.2

1.1

1.1

1.1

(oC)

50

50

50

50

50

50

55

55

55

Max. VF

1.03

1.03

1.03

1.03

1.03

1.03
SEENOTE (8)

SEENOTE (8)

SEE NOTE (8)

175

175

175

TC @ Rated IO

Typ. VF
TJ (Max)

150

(oC)

150

150

150

150

150

Avalanche Voltages

V(BR)Min
V(BR)Max

Notes:

Note 6
Note 7

Note 3
Note 4

Note 6
Note 7

Note 6
Note 7

Note 6
Note 7

Note 6
Note 7

Note 6
Note 7

(5) V(BR)MIN = 450 Volts For All 400 Volt Controlled Avalanche Bridges (i.e. Those Bridges With a Part Number Starting With The Letter "A")
(
650 Volts For All 600 Volt Controlled Avalanche Bridges, and
(
850 Volts For All 800 Volt Controlled Avalanche Bridges.
(7) V(BR)MAX = 900 Volts For All 400 Volt Controlled Avalanche Bridges,
1100 Volts For All 600 Volt Controlled Avalanche Bridges, and
1300 Volts For All 800 Volt Controlled Avalanche Bridges.
(8) Max. VF = 0.96 (VR = 100 to 600 Volts); 1.00 (VR = 800 to 1000 Volts)
(8) Typ. VF = 0.93 (VR = 100 to 600 Volts); 0.97 (VR = 800 to 1000 Volts)

FAST-ON TERMINALS

WIRE LEADS

FIGURE 2. EPOXY CASE WITH INTEGRALLY

MOLDED HEAT SINK
FAST-ON TERMINALS

WIRE LEADS

FIGURE 1. ELECTRICALLY ISOLATED METAL CASE

FIGURE3. IN-LINE CONFIGURATION. EPOXY

CASE WITH INTEGRALLY MOLDED
HEAT SINK
x
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

FAST RECOVERY BRIDGE RECTIFIER QUICK SELECTION GUIDE

SEE SECTION G
DIOTEC's Fast Recovery Bridge Rectifiers provide switching times ranging from 200nS to 500nS, some of the fastest in the industry!
These bridges are available with current ratings up 35 Amps at 1000 Volts. Switching times at these ratings are a maximum of 500nS!
Contact DIOTEC with your special requirements.
IO, AVERAGE RECTIFIED FORWARD CURRENT (AMPERES)
1.5

1
DT

DT
FSB200

FDI104

35

25

DT
FDB306

AC

SEE

SEE

SEE

SEE

FIGURE 1

FIGURE 2

FIGURE 1

FIGURE 2

RIGHT

RIGHT

RIGHT

RIGHT

VRRM
50

FDI100

FWB150

FSB200

FDB300

FDB600 FDB2500 FDB2500P FDB3500 FDB3500P

100

FDI101

FWB151

FSB201

FDB301

FDB601 FDB2501 FDB2501P FDB3501 FDB3501P

200

FDI102

FWB152

FSB202

FDB302

FDB602 FDB2502 FDB2502P FDB3502 FDB3502P

400

FDI104

FWB154

FSB204

FDB304

FDB604 FDB2504 FDB2504P FDB3504 FDB3504P

600

FDI106

FWB156

FSB206

FDB306

FDB606 FDB2506 FDB2506P FDB3506 FDB3506P

800

FDI108

FWB158

FSB208

FDB308

FDB608 FDB2508 FDB2508P FDB3508 FDB3508P

1000

FDI110

FWB150

FSB210

FDB310

FDB610 FDB2510 FDB2510P FDB3510 FDB3510P

35

30

FAST-ON TERMINALS

Typ. RJA
Typ. RJC

40

55

TC @ Rated IO ( C)
o

5.7

1.6

1.2

1.6

1.2

50

50

55

55

55

55

TA @ Rated IO ( C)

40

Max. VF

1.3

1.3

1.3

1.3

1.3

1.3

1.3

1.3

1.3

TJ (Max) (oC)

150

150

150

150

150

150

150

150

150

TRR
(nS)

WIRE LEADS

FIGURE 1. ELECTRICALLY ISOLATED

METAL CASE

55

TRR = 200nS: 0 < VRRM < 300;

TRR = 300nS: 300 < VRRM < 700;
TRR = 500nS: 700 < VRRM <1100

FAST-ON TERMINALS

WIRE LEADS

FIGURE 2. EPOXY CASE WITH INTEGRALLY

MOLDED HEAT SINK

PART NUMBERING SYSTEM

Example: FDI106 or FDB2506 (1 Amp, 600 Volt, or 25 Amp, 600 Volt Fast Recovery Bridge Rectifier. The First Product is Housed in a Dual In-Line Package; The Second in a Rectangular Package)

F BB C(C) VV
Blocking Voltage Reference (50 - 1000 Volts) - 2 Digits, e.g., 00 = 50 Volts; 02 = 200 Volts, 10 = 1000 Volts.
Current Reference (Average Forward Rectifed Current For Total Bridge) - 1 or 2 Digits. Range: 1 to 35 Amps.
Body Type Designator. Two Letters - See Table Below.
The Letter "F" Before the Body Designators DI, WB, SB, or DB Indicates This Product is a Fast Recovery Bridge Rectifer

BODY ID

DEFINITION

DB
DI
WB

Retangular Package, Small Vertical Elevation

Dual In-Line 4 Pin Package
Cylindercal Package

DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

xi

GENERAL PURPOSE SILICON DIODE QUICK SELECTION GUIDE

SEE SECTION H
DIOTEC's offers a number of axial lead, low cost, general purpose diodes which will satisfy a wide range of applications. A number
these diodes are available as DIOTEC's SOFT GLASS DIODES (SOFT GLASS DIODE is a DIOTEC Registered Trademark). These
SOFT GLASS DIODES provide the highest degree of operational reliability, efficiency, and high temperature/mechanical stress
reliability. More information on SOFT GLASS DIODES may be found in Appendix X.
IO, AVERAGE RECTIFIED FORWARD CURRENT (AMPERES)

VRRM

1.5

DO-41

DO-15

DO-41

SOFT
GLASS
DIODES

SOFT GLASS DIODES

DO-27

DO-27

SOFT GLASS DIODES

50

1N4001

1N4001G

GP100

S1A

1N5391

GP200

IN5400

1N5400G

GP400

GP600

100

1N4002

1N4002G

GP101

S1B

1N5392

GP201

IN5400

1N5400G

GP401

GP601

200

1N4003

1N4003G

GP102

S1D

1N5393

GP202

IN5400

1N5400G

GP402

GP602

400

1N4004

1N4004G

GP104

S1G

1N5395

GP204

IN5400

1N5400G

GP404

GP604

600

1N4005

1N4005G

GP106

S1J

1N5397

GP206

IN5400

1N5400G

GP406

GP606

800

1N4006

1N4006G

GP108

S1K

1N5398

GP208

IN5400

1N5400G

GP408

GP608

1000

1N4007

1N4007G

GP110

S1M

1N5399

GP210

IN5400

1N5400G

GP410

GP610

IFSM
(Amps)

50

50

50

30

60

70

200

200

200

400

TA @ Rated IO
(oC)

75

75

75

75

50

75

75

75

75

TJ (Max)
(oC)

175

175

175

175

175

175

175

100
Note 1

175

175

150

O
NOTES: (1) Temperature Rating: TL=100 C

PART NUMBERING SYSTEM

Example: GP102 (1 Amp, 200 Volt, Axial Lead General Purpose SOFT GLASS DIODE (SOFT GLASS DIODE is a DIOTEC Electronics Registered Trademark)

GP

A VV
Blocking Voltage Reference (50 - 1000 Volts) - 2 Digits. Examples: 02 = 200 Volts; 10 = 1000 Volts
Current Reference (Average Forward Rectified Current) - 1 Digit.
Soft Glass, General Purpose Diode Designator (See Note)

NOTE: The Single Exception to This System is The GP600 Series of Diodes. These diodes are
ARE NOT SOFT GLASS DIODES.

1N4000, 1N5391, 1N5400 - JEDEC Type Designation

1N4000G, 1N5400G - DIOTEC SOFT GLASS Equivalent of the JEDEC Type Designated Diode

DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

xi

FAST RECOVERY SILICON DIODE QUICK SELECTION GUIDE

SEE SECTION H
DIOTEC's Fast Recovery Diodes exhibit switching times in the range of 4 to 500nS. Additionally, many of these products are
SOFT GLASS DIODES (SOFT GLASS DIODE is a DIOTEC Registered Trademark). These SOFT GLASS DIODES provide the highest
degree of operational efficiency and high temperature/mechanical stress reliability. More information on SOFT GLASS DIODES may
be found in Appendix X.
IO, AVERAGE RECTIFIED FORWARD CURRENT (AMPERES)
0.15

DO-27

G-6A

TO-220AC

DO-41
DO-35

DO-41

VRRM

SOFT
GLASS
DIODES

SOFT GLASS DIODES

50

1N4933

RP100

RGP100

RGP200

RP300

RGP300

RP600

RGP800

1N4934

RP101

RGP101

RGP201

RP301

RGP301

RP601

RGP801

200

1N4935

RP102

RGP102

RGP202

RP302

RGP302

RP602

RGP802

400

1N4936

RP104

RGP104

RGP204

RP304

RGP304

RP604

RGP804

600

1N4937

RP106

RGP106

RGP206

RP306

RGP306

RP606

RGP806

800

RP108

RGP108

RGP208

RP308

RGP308

RP608

1000

RP110

RGP110

RGP210

RP310

RGP310

RP610

30

50

60

200

200

300

100

IFSM
(Amps)

1N4148
(Note 1)

Note 2

30

T C @ Rated IO
(oC)

150
110

TA @ Rated IO
(oC)

75

75

75

75

75

55

55

60

TJ (Max)
(oC)

175

175

175

175

175

175

175

175

T RR (nS)

200

TRR = 150nS: 0 < VRRM < 500;

TRR = 250nS: 500 < VRRM < 700;
TRR = 500nS: 700 < VRRM <1100 (Note 3)

150
Note 4

NOTES: ( 1 ) VRRM =75VOLTS

(2)ULTRA FAST SWITCHING DIODE: @ PULSE WIDTH OF 1 S e c , I FSM = 1 Amp; @ PULSE WIDTH OF 1 Sec, IFSM = 4 Amps
(3)300nSAVAILABLE, CONSULT FACTORY
(4)FOR 0< VRRM <300, T RR = 150 n S ; 3 0 0 < VRRM <500, T RR =200 nS; 500< VRRM <650 TRR = 250 n S

PART NUMBERING SYSTEM

Example: RP102 or RGP102 (1 Amp, 200 Volt, Axial Lead Fast Recovery Diode; The Second Product (RGP102) is a SOFT GLASS DIODE

R(G)P A VV
Blocking Voltage Reference (50 - 1000 Volts) - 2 Digits. Examples: 02 = 200 Volts; 10 = 1000 Volts
Current Reference (Average Forward Rectified Current) - 1 Digit.
Fast Recovery Diode Designator; With the "G" Present, Indicates That This Product is a SOFT GLASS DIODE
NOTE: The Single Exception to This System is The RGP800 Series of Fast Recovery Diodes. These diodes are provided in a TO-220AC Package.
Additionally, These Products ARE NOT SOFT GLASS DIODES.

1N4148, 1N4933 - JEDEC Type Designation

xii
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

SECTION A
SINGLE DIODE
SCHOTTKY
RECTIFIERS

AXIAL LEAD DO-41 AND DO-27 PACKAGES

1 TO 5 AMPERES
20 TO 100 VOLTS
DO - 41

DO - 27

2 PIN TO-220AC AND TO-247AC PACKAGES

DT OJ
6SK40

6 TO 30 AMPERES

DT 7G
15SK50

30 TO 100 VOLTS
TO - 220AC
TO - 247AC

DIOTEC ELECTRONICS CORP.

- 18020 Hobart Blvd., Unit B - Gardena, CA 90248 U.S.A. - PH: 310-767-1052 - FX: 310-767-7958

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDA-101-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-41 PACKAGE

Metal semiconductor junction with guard ring

SERIES 1N5817 - 1N5819

DO - 41

Epitaxial Construction

LL

Low forward voltage drop

BD (Dia)

High current capacity

BL

For use in low voltage, high frequency inverters, free wheeling,

and polarity protection applications

Color Band
Denotes
Cathode

MECHANICAL DATA
LL
Case: JEDEC DO-41, molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym

Polarity: Color band denotes cathode

BD

Weight: 0.012 Ounces (0.34 Grams)

LL
LD

4.1

0.205

5.2

0.103

2.6

0.107

2.7

1.00
0.028

25.4
0.71

0.034

0.86

0.160

BL
Mounting Position: Any

Maximum
In
mm

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

1N5817

1N5818

1N5819

30

40

Maximum DC Blocking Voltage

VRM

20

Maximum RMS Voltage

VRMS

14

21

28

Maximum Peak Recurrent Reverse Voltage

VRRM

20

30

40

Average Forward Rectified Current @ TL = 90 oC (TL measured on

cathode lead, 1/32 in. from case)

IO

IFSM

25

AMPS

Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 1 Amp DC

VFM

0.45

0.55

0.6

Maximum Forward Voltage at 3 Amps DC

VFM

0.75

0.875

0.9

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage (Note 1)
Typical Thermal Resistance, Junction to Ambient

@ TL = 25oC
o
@ TL = 100 C

1
10

mA

RJA

80

C/W
pF

CJ

110

Junction Operating Temperature Range

TJ

-65 to +125

TSTG

-65 to +150

NOTES: (1) Lead temperature reference is cathode lead 1/32 in from case.
(2) Measured at 1MHz & applied reverse voltage of 4 volts

VOLTS

IRM

Typical Junction Capacitance (Note 2)

Storage Temperature Range

VOLTS

C
4.97fsbda101

A1

Data Sheet No. SBDA-101-2B

DIOTEC ELECTRONICS, INC.

18020 Hobart Blvd., Unit B
Gardena, CA 90248 U.S.A
Tel.: (310) 767-1604 Fax: (310) 767-7958

1 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES 1N5817 - 1N5819
25

20

15

10

NOTE 1

NOTE 2
5

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
20.0

10.0

1N5817

10
1N5818

TJ = 125 oC

1.0

1.0

TJ = 75 oC

NOTE 3
0.1

1N5819

TJ = 25 oC

0.10
.01

Instantaneous Forward Voltage (Volts)

0.8

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

1.2

1.4

1.6

1.8

2.0

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

400

NOTES
100

(1) Single Phase, Half Wave, 60 Hz, Resistive or Inductive

Load, 0.375" (9mm) Lead Length
(2) JEDEC Method, 8.3 mSec. Single Half Sine Wave

TJ = 25 oC

(3) TJ = 25 C, Pulse Width = 300 Sec, 1.0% Duty Cycle

o

10
0.1

10

50

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

A2

4.97bsbda101

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDA-102-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-41 PACKAGE

Metal semiconductor junction with guard ring

SERIES SK102 - SK110

DO - 41

Epitaxial Construction

LL
Low forward voltage drop

BD (Dia)

High current capacity

BL

For use in low voltage, high frequency inverters, free wheeling,

and polarity protection applications

Color Band
Denotes
Cathode

MECHANICAL DATA
LL
Case: JEDEC DO-41, molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Sym
Polarity: Color band denotes cathode

Minimum
In
mm

Maximum
In
mm

BL

0.160

4.1

0.205

5.2

Mounting Position: Any

BD

0.103

2.6

0.107

2.7

Weight: 0.012 Ounces (0.34 Grams)

LL
LD

1.00
0.028

25.4
0.71

0.034

0.86

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

SK102 SK104 SK106 SK107

UNITS
SK108 SK110

Maximum DC Blocking Voltage

VRM

20

40

60

70

80

100

Maximum RMS Voltage

VRMS

14

28

42

49

56

70

Maximum Peak Recurrent Reverse Voltage

VRRM

20

40

60

70

80

100

Average Forward Rectified Current @ TL = 90 o C (TL measured on

cathode lead, 1/32 in. from case)
Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 1 Amp DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage (Note 1)
Typical Thermal Resistance, Junction to Ambient

IO

IFSM

40

AMPS

VFM
o

@ TL = 25 C
@ TL = 100oC

IRM

0.5

0.7
0.5
10

RJA

Typical Junction Capacitance (Note 2)

CJ

Junction Operating Temperature Range

TJ

Storage Temperature Range

VOLTS

0.8

VOLTS

0.1
5

mA

15

C/W
pF

110
-65 to +125

-65 to +150
C

TSTG

-65 to +150

NOTES: (1) Lead temperature reference is cathode lead 1/32 in from case.
(2) Measured at 1MHz & applied reverse voltage of 4 volts

A3

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDA-102-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SK102 - SK107 and SERIES SK108 - SK110
50

40

(2)
30
(1) SK102-107
(2) SK108-110

20

NOTE 2

NOTE 1
10
(1)

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

5.0

10

1.0

TJ = 125 oC

1.0
(1)

0.1

NOTE 3

0.1

TJ = 75 oC

(1) SK102-107
(2) SK108-110
0.01
TJ = 25 oC

0.01
0.9

NOTE 5

Instantaneous Forward Voltage (Volts)

0.001
20

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

40

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

NOTES

400
(1)

NOTE 4

(1) Single Phase, Half Wave, 60 Hz, Resistive or Inductive

Load, 0.375" (9mm) Lead Length

100

(2) JEDEC Method, 8.3 mSec. Single Half Sine Wave, Tc = 95 o C

(3) TJ = 25 C, Pulse Width = 300 Sec, 2.0% Duty Cycle
o

(1) SK102-107

(4) TJ = 25 oC, f = 1MHz, VSIG = 50 mV P-P

(2)

(2) SK108-110

(5) Legend for Figure 4, Typical Reverse Characteristics:

10
0.1

10

50

SK102-107

Reverse Voltage, (Volts)

SK108-110
FIGURE 5. TYPICAL JUNCTION CAPACITANCE

A4

4.97bsbda102

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDA-301- 1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-27 PACKAGE

Metal semiconductor junction with guard ring

SERIES 1N5820 - 1N5822

DO-27

Epitaxial Construction

LL

Low forward voltage drop

BD (Dia)

High current capacity

BL

For use in low voltage, high frequency inverters, free wheeling,

and polarity protection applications

Color Band
Denotes
Cathode

MECHANICAL DATA
LL
Case: JEDEC DO-27, molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym
Polarity: Color band denotes cathode

BL
BD

Mounting Position: Any

1.00
0.048

LL
LD

Weight: 0.04 Ounces (1.12 Grams)

25.4
1.2

Maximum
In
mm
9.28
0.365
0.205

5.2

0.052

1.3

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

UNITS

1N5820

1N5821

1N5822

Maximum DC Blocking Voltage

VRM

20

30

40

Maximum RMS Voltage

VRMS

14

21

28

VRRM

20

30

40

Series Number

Maximum Peak Recurrent Reverse Voltage

VOLTS

Average Forward Rectified Current @ TL = 90 C (TL measured on

cathode lead, 1/32 in, from case)

IO

IFSM

80

AMPS

Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 3 Amps DC

VFM

0.475

0.5

0.525

Maximum Forward Voltage at 9.4 Amps DC

VFM

0.85

0.9

0.95

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage (Note 1)
Typical Thermal Resistance, Junction to Ambient
Typical Junction Capacitance (Note 2)
Junction Operating Temperature Range
Storage Temperature Range

@ TA = 25 C
@ TA = 100oC

VOLTS

2
20

mA

RJA

28

C/W

CJ

110

pF

TJ

-65 to +125

TSTG

-65 to +150

IRM

C
4.97fsbd301

NOTES: (1) Measured at pulse width 300 Sec & 2.0% duty cycle.
(2) Measured at 1MHz & applied reverse voltage of 4 volts.

A5

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDA-301-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

3 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES 1N5820 - 1N5822
100

80

60
TL = 75 oC
40

NOTE 1

NOTE 2
20

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10

20
TJ = 100 oC

10
1.0
1N5821
1N5820
0.1

1.0

TJ = 75 oC

NOTE 3

NOTE 3
0.01

1N5822

TJ = 25 oC

0.1

0.9
0.001
20

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

40

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

1000

NOTES
(1) Single Phase, Half Wave, 60 Hz, Resistive or Inductive
Load, 0.375" (9mm) Lead Length

100

(2) JEDEC Method, 8.3 mSec. Single Half Sine Wave

(3) TJ = 25 C, Pulse Width = 300 Sec, 2.0% Duty Cycle
o

TJ = 25 oC

10
0.1

10

50

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

A6

4.97bsbda301

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDA-302-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-27 PACKAGE

Metal semiconductor junction with guard ring

SERIES SK302 - SK310

DO-27

Epitaxial Construction

LL
Low forward voltage drop

BD (Dia)

High current capacity

BL
For use in low voltage, high frequency inverters, free wheeling,
and polarity protection applications

Color Band
Denotes
Cathode

MECHANICAL DATA
LL
Case: JEDEC DO-27 molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Solderability: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym
Polarity: Color band denotes cathode

Maximum
In
mm

BL

0.365

9.28

Mounting Position: Any

BD

0.205

5.2

Weight: 0.04 Ounces (1.12 Grams)

LL
LD

0.052

1.3

25.4
1.2

1.00
0.048

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

SK302

SK304

SK306

SK307

SK310

60

70

100

42

56

70

70

100

Maximum DC Blocking Voltage

VRM

20

40

Maximum RMS Voltage

VRMS

14

28

Maximum Peak Recurrent Reverse Voltage

VRRM

20

40

60

Average Forward Rectified Current @ TL = 90 o C (TL measured on

cathode lead, 1/32 in. from case))

Typical Thermal Resistance, Junction to Ambient

AMPS
IFSM
VFM
o

@ TL= 25 C
@ TL = 100 oC

120

100

0.5

0.7

0.8

VOLTS

IRM

0.5
20

mA

RJA

20

C/W

Typical Junction Capacitance (Note 2)

CJ

Junction Operating Temperature Range

TJ

Storage Temperature Range

VOLTS

IO

Peak Forward Surge Current ( 8.3mS single half sine wave

superimposed on rated load)
Maximum Forward Voltage at 3 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage (Note 1)

UNITS

TSTG

pF

250
-65 to +125
-65 to +150

-65 to +150
C
4.97fsbda302

NOTES: (1) Lead temperature reference is cathode lead 1/32 in from case.
(2) Measured at 1MHz & applied reverse voltage of 4 volts

A7

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDA-302-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

3 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SK302 - SK310
180

150

(2)

(1) SK302-304

120

(2) SK306-310

(1)

(2)

90
(1) SK302-304

NOTE 1
60

(2) SK306-310

(1)

NOTE 2
30
1

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10.0

NOTE 4

50
TJ = 125 oC
(1)

1.0

10

(2)
(3)

0.1
TJ = 75 oC

NOTE 3
1.0
(1) SK302-304
(2) SK306
(3) SK307-310

0.01

TJ = 25 oC

0.1
0.85

0.001
20

Instantaneous Forward Voltage (Volts)

40

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

NOTES
(1) Single Phase, Half Wave, 60 Hz, Resistive or Inductive
Load, 0.375" (9mm) Lead Length
(2) JEDEC Method, 8.3 mSec. Single Half Sine Wave, Tc = 95 oC
(3) TJ = 25 C, Pulse Width = 300 Sec, 2.0% Duty Cycle
o

(4) Legend for Figure 4, Typical Reverse Characteristics:

SK302-306
SK307-310

A8

4.97bsbda302

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDA-501-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-27 PACKAGE

Metal semiconductor junction with guard ring

SERIES SK502 - SK510

DO-27

Epitaxial Construction

LL
Low forward voltage drop

BD (Dia)

High current capacity

BL
For use in low voltage, high frequency inverters, free wheeling,
and polarity protection applications

Color Band
Denotes
Cathode

MECHANICAL DATA
LL
Case: JEDEC DO-27, molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Solderability: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym
Polarity: Color band denotes cathode

Maximum
In
mm
9.28
0.365

BL
Mounting Position: Any

BD

Weight: 0.04 Ounces (1.12 Grams)

LL
LD

1.00
0.048

25.4
1.2

0.205

5.2

0.052

1.3

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

SK502

SK504

SK506

SK507

SK510

Maximum DC Blocking Voltage

VRM

20

40

60

70

100

Maximum RMS Voltage

VRMS

14

28

42

56

70

Maximum Peak Recurrent Reverse Voltage

VRRM

20

40

60

70

100

Average Forward Rectified Current @ TL = 90 o C (TL measured on

cathode lead, 1/32 in. from case)
Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 5 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage (Note 1)

IO

AMPS
IFSM

150

VFM

0.55

IRM

0.5
50

@ TA = 25 C
o
@ TA = 100 C

VOLTS

120
0.70

0.85
0.5
25

VOLTS
mA

RJA

15

C/W

Typical Junction Capacitance (Note 2)

CJ

250

pF

Junction Operating Temperature Range

TJ

Typical Thermal Resistance, Junction to Ambient

Storage Temperature Range

NOTES: (1) Measured at pulse width 300 Sec and 2% duty cycle.
(2) Measured at 1MHz and an applied reverse voltage of 4 volts.

TSTG

-65 to +125
-65 to +150

-65 to +150
C
4.97fsbda501

A9

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDA-501-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

5 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SK502 - SK510
180

150
(2)
(1) SK502-504

120

(2) SK506-510

(1)

(2)

90
(1) SK502-504

NOTE 1

(2) SK506-510

60
(1)

NOTE 2
30

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

50
10.0
(1)

10

TJ = 125 oC

(2)
(3)

1.0

NOTE 3

0.1

1.0

TJ = 75 oC
(1) SK502-504
(2) SK506-503
(3) SK510

TJ = 25 oC

0.01

NOTE 4

0.1
0.85

0.001
20

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

40

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

NOTES
(1) Single Phase, Half Wave, 60 Hz, Resistive or Inductive
Load, 0.375" (9mm) Lead Length
(2) JEDEC Method, 8.3 mSec. Single Half Sine Wave, Tc = 95 oC
(3) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle
(4) Legend for Figure 4, Typical Reverse Characteristics:
SK502-504
SK506-510

A10

4.97bsbda501

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDR-601-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
TO-220AC PACKAGE

Low switching noise

FULLY INSULATED PACKAGE

Low forward voltage drop

A
A1

DT OJ
6SK40

Low thermal resistance

D4
D1

High switching capability

DT OJ

High surge capability

6SK40

B4

High reliability

B3

D2

MECHANICAL DATA

D3
3

Case: TO-220 molded plastic (Fully Insulated)

(U/L Flammability Rating 94V-0)
Sym

Terminals: Rectangular pins w/ standoff

Solderability: Per MIL-STD 202 Method 208 guaranteed

Polarity: Diode depicted on product

Mounting Position: Any

Weight: 0.06 Ounces (1.7 Grams)

Minimum
in
mm

Maximum
in
mm
0.187 4.75

B1

B2

A2

B1

A
A1 0.121* 4.75*
A2 0.14*
3.56*
B 0.035 0.9
0.043 1.1
2.3
0.102 2.6
B1 0.09
B2 0.025* 0.64*
B3 0.050* 1.27*
0.04
B4
1.0
C
0.413 10.5
0.61 15.5
D 0.59 15.0
D1 0.262* 6.6*
0.16
4.0
D2
D3 0.54 13.7
0.60 15.2
D4 0.108* 2.75*
P 0.126* 3.2*
* These dimensions are "Typicals".

ITO - 220AC

SERIES 6SK40 - 6SK100

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

Series Number
Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM
o

Average Forward Rectified Current @ TC =100 C

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 6 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

RATINGS

SYMBOL

@ TJ = 25 oC
@ TJ = 100 oC

Typical Thermal Resistance, Junction to Case (on heat sink)

6SK40

6SK50

6SK60

6SK70

6SK100

40

50

60

70

100

IO

IFSM

120

VFM
IRM
RJC

UNITS

0.55

AMPS
0.65

0.5
50

0.85
0.1
25

VOLTS

VOLTS
mA
C/W

A11

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDR-601-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

6 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES 6SK40 - 6SK100
200

160

120

80

40

0
o

10

Case Temperature, C

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
(1) 6SK40-50
(2) 6SK60-70
(3) 6SK100

10
TJ = 125 oC
(1)

(2)

1.0

10

0.1

TJ = 75 oC

(3)

1.0

TJ = 25 oC

NOTE 1

0.01

.001

0.1

Instantaneous Forward Voltage (Volts)

20

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

4000

NOTE 2

NOTES

1000

(1) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

(2) TJ = 25 oC, f = 1 MHz, VSIG = 50 mV P-P
TJ = 25 oC

100
0.1

10

50

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

A12

4.97bsbdr601

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDR-1201-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
TO-220AC PACKAGE

Low switching noise

FULLY INSULATED PACKAGE

Low forward voltage drop

A
A1

DT OJ
12SK40

Low thermal resistance

D4
D1

High switching capability

DT 6J

High surge capability

2

12SK40

B4

High reliability

B3

D2

MECHANICAL DATA
3
Case: TO-220 molded plastic (Fully Insulated)
(U/L Flammability Rating 94V-0)

Sym

Terminals: Rectangular pins w/ standoff

Solderability: Per MIL-STD 202 Method 208 guaranteed

Polarity: Diode depicted on product

Mounting Position: Any

Weight: 0.06 Ounces (1.7 Grams)

A
A1
A2
B
B1
B2
B3
B4
C
D
D1
D2
D3
D4

D3

Minimum
mm
in

Maximum
mm
in
0.187 4.75

B1

0.121*
0.14*
0.035
0.09
0.025*
0.050*

4.75*
3.56*
0.9
0.043 1.1
2.3
0.102 2.6
0.64*
1.27*
0.04
1.0
0.413 10.5
0.59 15.0
0.61 15.5
0.262* 6.6*
0.16
4.0
0.54 13.7
0.60 15.2
0.108* 2.75*
P 0.126* 3.2*
* These dimensions are "Typicals".

B
B1

B2
A2

ITO - 220AC
SERIES 12SK40 - 12SK100

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

Series Number
Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

12SK40

12SK50

12SK60

40

50

60

UNITS
12SK70 12SK100

70

100

VOLTS

VRRM
o

Average Forward Rectified Current @ TC = 100 C

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 12 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

RATINGS

SYMBOL

@ TJ = 25 oC
@ TJ = 100 oC

Typical Thermal Resistance, Junction to Case (on heat sink)

IO

12

IFSM

180

VFM
IRM
RJC

0.58

AMPS
0.68

0.5
50

0.85
0.1
25

VOLTS
mA
C/W

A13

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDR-1201-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

12 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES 12SK40 - 12SK100
200

160

120

80

40

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
(1) 12SK40-50
(2) 12SK60-70
(3) 12SK100

10
TJ = 125 oC
(1)

(2)
1.0

10

TJ = 75 oC
0.1
(3)

1.0

TJ = 25 oC

NOTE 1

0.01

.001

0.1

20

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

4000

TJ = 25 oC

NOTES

1000

(1) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

100
0.1

10

50

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

A14

4.97bsbdr120

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDR-1601-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE TO-247AC

(TO-3PAC) PACKAGE

Low switching noise

A
Low forward voltage drop

A2

Low thermal resistance

C
D1

DT 7G
16SK50

RO

High switching capability

D
P

DT 7G
16SK50

High surge capability

High reliability

L1

L2

MECHANICAL DATA

Case: TO-247 (TO-3P) molded plastic (U/L Flammability

Rating 94V-0)

Solderability: Per MIL-STD 202 Method 208 guaranteed

Polarity: Diode depicted on product

Mounting Position: Any

Weight: 0.19 Ounces (5.5 Grams)

B2*

A1
Maximum
mm
in
A
0.205
5.2
A1
0.102
2.6
A2
0.085
2.16
B
0.055
1.4
0.032
0.81
B1
B2
0.094
2.39
B3
0.126
3.2
0.215
5.46
B4
C 0.602 15.29 0.625 15.88
D 0.776 19.7 0.799 20.3
5.69
D1 0.209 5.31 0.224
L 0.559 14.2 0.582 14.8
L1 0.146 3.71 0.189
4.8
0.063
1.6
L2
5.7
RO 0.209
5.3 0.224
3.3 0.145
3.7
P 0.13

Sym

Terminals: Rectangular pins w/ standoff

B1

Minimum
mm
in
0.19
4.82
0.087 2.21
0.075 1.9
0.045 1.14
0.022 0.56
0.079 2.01
0.116 2.95

B3
B4

B4

* Applies to Pins 1 and 3

TO-247AC (TO - 3PAC)

SERIES 16SK40 - 16SK100

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

Series Number
Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM

Average Forward Rectified Current @ TC = 100 oC

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 16 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

RATINGS

SYMBOL

@ TJ = 25 oC
@ TJ = 100 oC

Typical Thermal Resistance, Junction to Case (on heat sink)

16SK40

16SK50

16SK60

40

50

60

IO

16

IFSM

240

VFM
IRM
RJC

0.55

UNITS
16SK70 16SK100

70

100

AMPS
0.65

1
50

0.85
0.5
25

VOLTS

VOLTS
mA
C/W

A15

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDR-1601-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

16 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES 16SK40 - 16SK100
250

200

150

100

50

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
(1) 16SK40-50
(2) 16SK60-70
(3) 16SK100

10
TJ = 125 oC
(2)

(1)

1.0

10

TJ = 75 oC
0.1
(3)

1.0

TJ = 25 oC

NOTE 1

0.01

.001

0.1

20

Instantaneous Forward Voltage (Volts)

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

4000

NOTES

1000

(1) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

TJ = 25 oC

100
0.1

10

50

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

A16

4.97bsbdr160

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDR-3001-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE TO-247AC

(TO-3PAC) PACKAGE

Low switching noise

A
A2

Low forward voltage drop

Low thermal resistance

C
D1

DT 7G
30SK50

RO

High switching capability

DT 7G
30SK50

High surge capability

High reliability

L1

L2

MECHANICAL DATA

Case: TO-247 (TO-3P) molded plastic (U/L Flammability

Rating 94V-0)

B1

Maximum
mm
in
0.205
5.2
A
A1
0.102
2.6
A2
0.085
2.16
B
0.055
1.4
B1
0.032
0.81
B2
0.094
2.39
B3
0.126
3.2
0.215
5.46
B4
C 0.602 15.29 0.625 15.88
D 0.776 19.7 0.799 20.3
5.69
D1 0.209 5.31 0.224
L 0.559 14.2 0.582 14.8
4.8
L1 0.146 3.71 0.189
0.063
1.6
L2
5.7
RO 0.209
5.3 0.224
3.7
3.3 0.145
P 0.13

Sym

Terminals: Rectangular pins w/ standoff

Solderability: Per MIL-STD 202 Method 208 guaranteed

Polarity: Diode depicted on product

Mounting Position: Any

Weight: 0.20 Ounces (5.5 Grams)

B2*

A1

Minimum
mm
in
0.19
4.82
0.087 2.21
0.075 1.9
0.045 1.14
0.022 0.56
0.079 2.01
0.116 2.95

B3
B4

B4

* Applies to Pins 1 and 3

TO-247AC (TO-3PAC)
SERIES 30SK40 - 30SK70

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

Series Number
Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM
o

Average Forward Rectified Current @ TC = 100 C

30SK40

30SK50

30SK60

30SK70

30

40

50

60

70

Typical Thermal Resistance, Junction to Case (on heat sink)

VOLTS

30

IFSM

600

VFM

0.55

@ TJ = 25 C
@ TJ = 100 oC

UNITS

30SK30

IO

Peak Forward Surge Current ( 8.3mS single half sine wave

superimposed on rated load)
Maximum Forward Voltage at 30 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

RATINGS

SYMBOL

AMPS

450
0.65

0.85

VOLTS

IRM

1
100

mA

RJC

1.3

C/W

A17

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDR-3001-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

30 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES 30SK40 - 30SK70
600
(1)

(1) 30SK30-50
(2) 30SK60-70

500
(2)
400

300

200

100

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
(1) 30SK30-50
(2) 30SK60
(3) 30SK70

10
TJ = 125 oC
(2)

10

(1)

1.0

0.1

TJ = 75 oC

(3)

1.0

TJ = 25 oC

NOTE 1

0.01

NOTE 2
.001

0.1

20

Instantaneous Forward Voltage (Volts)

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

4000

NOTES

1000

(1) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

(2) TJ = 25 oC, f = 1.0 MHz, VSIG = 50 mV P-P

100
0.1

10

50

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

A18

4.97bsbdr300

SECTION B
DUAL DIODE
SCHOTTKY
RECTIFIERS

DT 4F
SK1240C

DT 5G
SK4060C

3 PIN TO-220AB AND TO-247AB PACKAGES

12 TO 60 AMPERES
TO - 220AB

30 TO 100 VOLTS

DIOTEC ELECTRONICS CORP.

TO - 247AB

- 18020 Hobart Blvd., Unit B - Gardena, CA 90248 U.S.A. - PH: 310-767-1052 - FX: 310-767-7958

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDT-1200-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
TO-22OAB PACKAGE

Low switching noise

FULLY INSULATED PACKAGE

A

Low forward voltage drop

DT 4F
SK1240C

Low thermal resistance

A1

D4
D1

High switching capability

High surge capability

DT 4F
SK1240C

High reliability

B3

MECHANICAL DATA
3

D2
D3

Case: TO-220 molded plastic (Fully Insulated)

(U/L Flammability Rating 94V-0)
Sym

Terminals: Rectangular pins w/ standoff

Solderability: Per MIL-STD 202 Method 208 guaranteed
Polarity: Diode depicted on product
Mounting Position: Any
Weight: 0.06 Ounces (1.75 Grams)

A
A1
A2
B
B1
B2
B3
C
D
D1
D2
D3
D4

Minimum
mm
in

B1

Maximum
mm
in
0.187 4.75

B2

A2

B1

0.055*
0.14*
0.035
0.09
0.028*
0.051*

1.4*
3.56*
0.9
0.043 1.1
0.102 2.6
2.3
0.66*
1.3*
0.410 10.4
0.59 15.0
0.61 15.5
0.25*
6.4*
0.16
4.0
0.53 13.5
0.57 14.8
0.108* 2.75*
P 0.141* 3.58*
* These dimensions are "Typicals".

ITO-220AB
SERIES SK1240C - SK12100C

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

Series Number
Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM

Average Forward Rectified Current @ TC = 100 oC

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage Drop (per diode) at 6 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

RATINGS

SYMBOL

@ TJ = 25 oC
@ TJ = 100 oC

Typical Thermal Resistance, Junction to Case (on heat sink)

SK
1240C

SK
1250C

SK
1260C

SK
1270C

12100C

40

50

60

70

100

IO

12

IFSM

120

VFM
IRM
RJC

UNITS

0.55

SK

AMPS
0.65

0.5
50

0.85
0.2
10

2.5

VOLTS

VOLTS
mA
C/W

B1

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDT-1200-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

12 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SK1240C - SK12100C
150

120

90

60

NOTE 1
30

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
(1) SK1240C-1250C
(2) SK1260C-1270C
(3) SK12100C

100

(2)

(1)

10

10

TC = 100 oC
TC = 75 oC
1.0
(3)

1.0

NOTE 2

0.1

TC = 25 oC
0.01

0.1

20

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

4000

NOTES
1000

(1) JEDEC Method, 8.3 mSec. Single Half Sine Wave

NOTE 3

(2) TJ = 25 C, Pulse Width = 300 Sec, 2.0% Duty Cycle

o

(3) TC =25 o C, f = 1.0 MHz, VSIG = 50 mV P-P

100
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

B2

4.97bsbdt12

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDT-1600-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
TO-220AB PACKAGE

Low switching noise

FULLY INSULATED PACKAGE

A

Low forward voltage drop

DT 1A
SK1640C

Low thermal resistance

A1

D4
D1

High switching capability

High surge capability

DT 1A
SK1640C

High reliability
2
B3

MECHANICAL DATA

D2
D3

Case: TO-220 molded plastic (Fully Insulated)

(U/L Flammability Rating 94V-0)

1
B1

Terminals: Rectangular pins w/ standoff

Sym
A
A1
A2
B
B1
B2
B3
C
D
D1
D2
D3
D4

Minimum
mm
in

Polarity: Diode depicted on product

Mounting Position: Any
Weight: 0.06 Ounces (1.75 Grams)

A2

B1

1.4*
3.56*
0.9
0.043 1.1
2.3
0.102 2.6
0.66*
1.3*
0.410 10.4
0.59 15.0
0.61 15.5
0.25*
6.4*
0.16
4.0
0.53 13.5
0.57 14.8
0.108* 2.75*
P 0.141* 3.58*
* These dimensions are "Typicals".

Solderability: Per MIL-STD 202 Method 208 guaranteed

B2

Maximum
mm
in
0.187 4.75

0.055*
0.14*
0.035
0.09
0.028*
0.051*

ITO-220AB
SERIES SK1640C - SK16100C

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

Series Number
Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM

Average Forward Rectified Current @ TC = 110 oC

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage Drop (per diode) at 8 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

RATINGS

SYMBOL

Typical Thermal Resistance, Junction to Case (on heat sink)

SK
1650C

SK
1660C

SK
1670C

16100C

40

50

60

70

100

16

IFSM

160

VFM

@ TJ = 25 C
o
@ TJ = 125 C

SK
1640C

IO

IRM
RJC

UNITS

0.55

SK

AMPS
0.65

0.5
50

0.85
0.2
10

1.5

VOLTS

VOLTS
mA
C/W

B3

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDT-1600-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

16 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SK1640C - SK16100C
200

160

120

80

NOTE 1
40

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
(1) SK1640C-1650C
(2) SK1660C-1670C
(3) SK16100C

100

(1)

(2)
10

10

TC = 100 oC
TC = 75 oC
1.0
(3)

1.0

NOTE 2

0.1

TC = 25 oC
0.01

0.1

20

Instantaneous Forward Voltage (Volts)

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

4000

NOTES
1000

(1) JEDEC Method, 8.3 mSec. Single Half Sine Wave

NOTE 3

(2) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

(3) TC =25 oC, f = 1.0 MHz, VSIG = 50 mV P-P

100
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

B4

4.97bsbdt16

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDT-2400-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF TO-247AB

(TO-3PAB) PACKAGE

Low switching noise

A
C

A2

Low forward voltage drop

Low thermal resistance

D1

DT 5G
SK2460C

RO

High switching capability

DT 5G
SK2460C

High surge capability

High reliability

L1
2
L

MECHANICAL DATA
B1
1

Case: TO-247 (TO-3P) molded plastic (U/L Flammability

Rating 94V-0)

Maximum
mm
in
A
0.205
5.2
0.102
2.6
A1
0.085
2.16
A2
0.055
B
1.4
0.032
0.81
B1
0.094
2.39
B2
B3
0.126
3.2
0.215
5.46
B4
C 0.602 15.29 0.625 15.88
D 0.776 19.7 0.799 20.3
5.69
D1 0.209 5.31 0.224
L 0.559 14.2 0.582 14.8
4.8
L1 0.146 3.71 0.189
RO 0.209
5.3 0.224
5.7
P 0.13
3.3 0.145
3.7

Sym

Terminals: Rectangular pins w/ standoff

Solderability: Per MIL-STD 202 Method 208 guaranteed
Polarity: Diode depicted on product
Mounting Position: Any
Weight: 0.20 Ounces (5.5 Grams)

B2*

A1

Minimum
mm
in
0.19
4.82
0.087 2.21
0.075 1.9
0.045 1.14
0.022 0.56
0.079 2.01
0.116 2.95

B3
B4

B4

*Applies to Pins 1 and 3

TO-247AB (TO-3PAB)
SERIES SK2440C - SK24100C

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

Series Number
Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM

Average Forward Rectified Current @ TC = 100 oC

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage Drop (per diode) at 12 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

RATINGS

SYMBOL

Typical Thermal Resistance, Junction to Case (on heat sink)

SK
2450C

SK
2460C

SK
2470C

24100C

40

50

60

70

100

24

IFSM

200

VFM

@ TJ = 25 C
@ TJ = 125 oC

SK
2440C

IO

IRM
RJC

UNITS

0.55

1.5

VOLTS

AMPS
0.65

0.5
100

SK

0.85

VOLTS

0.2
15

mA
C/W

B5

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDT-2400-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

24 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SK2440C - SK24100C
200

160

120

80

NOTE 1
40

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
(1) SK1640C-1650C
(2) SK1660C-1670C
(3) SK16100C

100

(1)

(2)
10

10

TC = 100 oC
TC = 75 oC
1.0
(3)

1.0

NOTE 2

0.1

TC = 25 oC
0.01

0.1

20

Instantaneous Forward Voltage (Volts)

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

4000

NOTES
1000

(1) JEDEC Method, 8.3 mSec. Single Half Sine Wave

NOTE 3

(2) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

(3) TC =25 oC, f = 1.0 MHz, VSIG = 50 mV P-P

100
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

B6

4.97bsbdt24

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDT-3000-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF TO-247AB

(TO-3PAB) PACKAGE

Low switching noise

A
C

A2

Low forward voltage drop

D1

DT 5G
SK3060C

Low thermal resistance

RO

High switching capability

DT 5G
SK3060C

High surge capability

High reliability

L1

2
L

MECHANICAL DATA
B1
3

Case: TO-247 (TO-3P) molded plastic (U/L Flammability

Rating 94V-0)

Maximum
mm
in
0.205
5.2
A
A1
0.102
2.6
A2
0.085
2.16
B
0.055
1.4
B1
0.032
0.81
B2
0.094
2.39
B3
0.126
3.2
0.215
5.46
B4
C 0.602 15.29 0.625 15.88
D 0.776 19.7 0.799 20.3
5.69
D1 0.209 5.31 0.224
L 0.559 14.2 0.582 14.8
4.8
L1 0.146 3.71 0.189
RO 0.209
5.3 0.224
5.7
3.3 0.145
3.7
P 0.13

Sym

Terminals: Rectangular pins w/ standoff

Solderability: Per MIL-STD 202 Method 208 guaranteed
Polarity: Diode depicted on product
Mounting Position: Any
Weight: 0.20 Ounces (5.5 Grams)

B2*

A1

Minimum
mm
in
0.19
4.82
0.087 2.21
0.075 1.9
0.045 1.14
0.022 0.56
0.079 2.01
0.116 2.95

B3
B4

B4

*Applies to Pins 1 and 3

TO-247AB (TO-3PAB)
SERIES SK3040C - SK30100C

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

Series Number
Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

UNITS

SK
3040C

SK
3050C

SK
3060C

SK
3070C

30100C

SK

40

50

60

70

100

VOLTS

VRRM
o

Average Forward Rectified Current @ TC = 90 C)

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage Drop (per diode) at 15 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

RATINGS

SYMBOL

30

IFSM

200

VFM
o

@ TJ = 25 C
@ TJ = 125 oC

Typical Thermal Resistance, Junction to Case (on heat sink)

IO

IRM
RJC

AMPS
0.57

0.65
0.5
100
1.2

0.85

VOLTS

0.2
15

mA
C/W

B7

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDT-3000-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

30 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SK3040C - SK30100C SERIES
300

240

180

120

JEDEC Method, 8.3 mSec.

Single Half Sine Wave

60

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
100
TJ = 125 oC

TJ = 150 oC
TJ = 125 oC
10

10

1.0

TJ = 25 oC

TJ = 75 oC

1.0
0.1

TJ = 25 oC
0.01

0.1

20

Instantaneous Forward Voltage (Volts)

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

4000

1000

100
0.1

10

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

B8

100

Average Forward Current, Amperes

FIGURE 6. FORWARD POWER DISSIPATION

4.97bsbdt30

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDT-4000-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF TO-247AB

(TO-3PAB) PACKAGE

Low switching noise

A
C

A2

Low forward voltage drop

D1

DT 5G
SK4060C

Low thermal resistance

RO

High switching capability

DT 5G
SK4060C

High surge capability

High reliability

L1

2
L

MECHANICAL DATA
B1
3
Case: TO-247 (TO-3P) molded plastic (U/L Flammability
Rating 94V-0)

Maximum
mm
in
0.205
5.2
A
A1
0.102
2.6
A2
0.085
2.16
B
0.055
1.4
B1
0.032
0.81
B2
0.094
2.39
B3
0.126
3.2
0.215
5.46
B4
C 0.602 15.29 0.625 15.88
D 0.776 19.7 0.799 20.3
5.69
D1 0.209 5.31 0.224
L 0.559 14.2 0.582 14.8
4.8
L1 0.146 3.71 0.189
RO 0.209
5.3 0.224
5.7
3.3 0.145
3.7
P 0.13

Sym

Terminals: Rectangular pins w/ standoff

Solderability: Per MIL-STD 202 Method 208 guaranteed
Polarity: Diode depicted on product
Mounting Position: Any
Weight: 0.20 Ounces (5.5 Grams)

B2*

A1

Minimum
mm
in
0.19
4.82
0.087 2.21
0.075 1.9
0.045 1.14
0.022 0.56
0.079 2.01
0.116 2.95

B3
B4

B4

*Applies to Pins 1 and 3

TO-247AB (TO-3PAB)
SERIES SK4040C - SK40100C

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

Series Number
Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

UNITS

SK
4040C

SK
4050C

SK
4060C

SK
4070C

40100C

SK

40

50

60

70

100

VOLTS

VRRM
o

Average Forward Rectified Current @ TC = 85 C)

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage Drop (per diode) at 20 Amps
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

RATINGS

SYMBOL

40

IFSM

200

VFM
o

@ TJ = 25 C
@ TJ = 125 oC

Typical Thermal Resistance, Junction to Case (on heat sink)

IO

IRM
RJC

AMPS
0.6

0.7
2.0
100
1.2

0.92

VOLTS

2.0
50

mA
C/W

B9

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDT-4000-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

40 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SK4040C - SK40100C SERIES
300

240

180

120

JEDEC Method, 8.3 mSec.

Single Half Sine Wave

60

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
100
TJ = 125 oC

TJ = 150 oC
TJ = 125 oC
10

10

1.0

TJ = 25 oC

TJ = 75 oC

1.0
0.1

TJ = 25 oC
0.01

0.1

20

Instantaneous Forward Voltage (Volts)

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

4000

1000

100
0.1

10

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

B10

100

Average Forward Current, Amperes

FIGURE 6. FORWARD POWER DISSIPATION

4.97bsbdt40

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDT-6000-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF TO-247AB

(TO-3PAB) PACKAGE

Low switching noise

A
C

A2

Low forward voltage drop

Low thermal resistance

D1

DT 5G
SK6060C

RO

High switching capability

DT 5G
SK6060C

High surge capability

High reliability

L1

2
L

MECHANICAL DATA
B1
Case: TO-247 (TO-3P) molded plastic (U/L Flammability
Rating 94V-0)

Maximum
mm
in
0.205
5.2
A
0.102
A1
2.6
0.085
A2
2.16
0.055
B
1.4
0.032
B1
0.81
0.094
B2
2.39
B3
0.126
3.2
0.215
5.46
B4
C 0.602 15.29 0.625 15.88
D 0.776 19.7 0.799 20.3
5.69
D1 0.209 5.31 0.224
L 0.559 14.2 0.582 14.8
4.8
L1 0.146 3.71 0.189
RO 0.209
5.3 0.224
5.7
3.3 0.145
3.7
P 0.13

Sym

Terminals: Rectangular pins w/ standoff

Solderability: Per MIL-STD 202 Method 208 guaranteed
Polarity: Diode depicted on product
Mounting Position: Any
Weight: 0.20 Ounces (5.5 Grams)

B2*

A1

Minimum
mm
in
0.19
4.82
0.087 2.21
0.075 1.9
0.045 1.14
0.022 0.56
0.079 2.01
0.116 2.95

B3
B4

B4

*Applies to Pins 1 and 3

TO-247AB (TO-3PAB)
SERIES SK6030C - SK6070C

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

Series Number
Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM

Average Forward Rectified Output Current @ TC = 90 oC

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage Drop (per diode) at 30 Amps
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

RATINGS

SYMBOL

Typical Thermal Resistance, Junction to Case (on heat sink)

SK
6030C

SK
6040C

SK
6050C

SK
6060C

SK
6070C

30

40

50

60

70

IO

60

IFSM

600

VFM
o

@ TJ = 25 C
@ TJ = 125 oC

IRM
RJC

UNITS

0.55

AMPS
0.65

5.0
200
1.1

VOLTS

VOLTS
mA
C/W

B11

DIOTEC ELECTRONICS CORP.

Data Sheet No. SBDT-6000-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

60 AMP SCHOTTKY BARRIER RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SK6030C - SK6070C SERIES
750

600
(1)
450
(2)

300
(1) SK6030C - 6050C
(2) SK6060C - 6070C
150

0
1

Case Temperature, oC
FIGURE 1. FORWARD CURRENT DERATING CURVE

JEDEC Method, 8.3 mSec.

Single Half Sine Wave

10

100

Number of Cycles at 60 Hz

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

1000

TJ = 150 oC
100
TJ = 125 oC

100
TJ = 125 oC
10

10

1.0

TJ = 25 oC

TJ = 75 oC

TJ = 25 oC

0.1
20

SK6030C - SK6050C

60

80

100

120

140

1.0

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

100
TJ = 125 oC
7000

10

TJ = 25 oC

SK6060C - SK6070C

1.0

Instantaneous Forward Voltage (Volts)

1000
700

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

0.5

10

60

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

B12

4.97bsbdt60

SECTION C
SUPER EFFICIENT and
ULTRA FAST RECOVERY
DIODES
Single Diode Products

AXIAL LEAD DO-41, DO-27, AND G-6A PACKAGES

1 TO 6 AMPERES
50 TO 1000 VOLTS
DO - 41

DO - 27

G-6A

2 PIN TO-220AC PACKAGE

DT 5B
8SPR05

6 TO 15 AMPERES
50 TO 600 VOLTS
TO - 220AC

DIOTEC ELECTRONICS CORP.

- 18020 Hobart Blvd., Unit B - Gardena, CA 90248 U.S.A. - PH: 310-767-1052 - FX: 310-767-7958

DIOTEC ELECTRONICS CORP

Data Sheet No. SESA-100-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-41 PACKAGE

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

SERIES SPR11 - SPR14

DO - 41

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

LOW SWITCHING NOISE

LOW THERMAL RESISTANCE
BL

HIGH SWITCHING CAPABILITY

Color Band
Denotes
Cathode

LOW FORWARD VOLTAGE DROP

MECHANICAL DATA

LL
Case: JEDEC DO-41 molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Solderability: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym
Polarity: Color band denotes cathode

Maximum
In
mm

BL

0.160

4.1

0.205

5.2

Mounting Position: Any

BD

0.103

2.6

0.107

2.7

Weight: 0.013 Ounces (0.35 Grams)

LL
LD

1.00
0.028

25.4
0.71

0.034

0.86

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

SPR11

SPR12

SPR13

SPR14

Maximum DC Blocking Voltage

VRM

100

200

300

400

Maximum RMS Voltage

VRMS

70

140

210

280

VRRM

100

200

300

400

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ TA = 55 C

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 1 Amp DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Ambient
Typical Junction Capacitance (Note 1)
Junction Operating and Storage Temperature Range
NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

IFSM

30

VFM
o

@ TC = 25 C
o
@ TC = 100 C

Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)

IO

0.95

VOLTS

AMPS
1.25

VOLTS

IRM

2.0
50

RJA

50

C/W

CJ

50

pF

TRR

35

nSec

TJ, TSTG

-65 to +150

C
4.97fsesa1

C1

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-100-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1 AMP SUPER EFFICIENT RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SPR11 - SPR14
30

Resistive and Inductive Loads

24

18

NOTE 1
12

NOTE 2
6

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10
100

TJ = 150 oC

1.0

10

TJ = 100 oC
1.0

0.1

0.1

TJ = 25 oC

0.01
0.01
20

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

0.001

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

Instantaneous Forward Voltage (Volts)
FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

NOTES

70

(1) Single Phase, Half Wave, 60 Hz; Lead Length = 0.375" (9.5mm)
60

NOTE 4

(2) JEDEC Method, 8.3 mSec. Single Half Sine Wave

(3) TJ = 25 oC, Pulse Width = 300 Sec, 1.0% Duty Cycle

50

(4) TJ =25 C, f = 1.0 MHz, 2% Duty Cycle.

40
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

C2

4.97bsesa1

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-101-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-41 PACKAGE

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

SERIES UFR100 - UFR110

DO - 41

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

LOW SWITCHING NOISE

LOW THERMAL RESISTANCE
BL

HIGH SWITCHING CAPABILITY

Color Band
Denotes
Cathode

LOW FORWARD VOLTAGE DROP

MECHANICAL DATA

LL
Case: JEDEC DO-41 molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads
LD (Dia)
Solderability: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym

Polarity: Color band denotes cathode

Mounting Position: Any
Weight: 0.013 Ounces (0.35 Grams)

Maximum
In
mm

BL

0.160

4.1

0.205

5.2

BD

0.103

2.6

0.107

2.7

LL
LD

1.00
0.028

25.4
0.71

0.034

0.86

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

SYMBOL

RATINGS

Maximum DC Blocking Voltage

VRM

UFR UFR UFR UFR UFR UFR UFR UFR UFR

100 101 102 103 104 105 106 108 110
50 100 200 300 400 500 600 800 1000

Maximum RMS Voltage

VRMS

35

70 140 210 280 350

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100 200 300 400 500

Series Number

Average Forward Rectified Current @ TA = 55 oC

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)

Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)

NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

IFSM

35
1.25

420 560

700 VOLTS

600 800 1000

AMPS
1.7

@ TC = 25 C
o
@ TC = 125 C

Typical Junction Capacitance (Note 1)

Junction Operating and Storage Temperature Range

VFM

Maximum Forward Voltage at 1 Amp DC

Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Ambient

IO

UNITS

VOLTS

IRM

2.0
50

RJA

50

C/W

CJ

15

pF

TRR
TJ, TSTG

50
-65 to +150

75

nSec
C
3.01 ufr100

C3

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-101-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1 AMP ULTRAFAST RECOVERY DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES UFR100 - UFR110
30

Resistive and Inductive Loads

24

18

NOTE 1
12

NOTE 2
6

Case Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10
100
TJ = 150 oC

UFR100-104

1.0

10

TJ = 100 oC
UFR106-110

1.0

0.1

0.1

TJ = 25 oC

0.01
0.01
20

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

0.001

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

Instantaneous Forward Voltage (Volts)
FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

100

NOTES
(1) Single Phase, Half Wave, 60 Hz; Lead Length = 0.375" (9.5mm)
UFR106-110

(2) JEDEC Method, 8.3 mSec. Single Half Sine Wave

UFR100-104

(3) TJ = 25 oC, Pulse Width = 300 Sec, 1.0% Duty Cycle

10

NOTE 4

(4) TJ =25 C, f = 1.0 MHz, 2% Duty Cycle.

6
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

C4

4.97bsesa1a

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-200-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-41 PACKAGE

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

SERIES:

SPR21 - SPR23
UFR24 - UFR28

DO - 41

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

LOW SWITCHING NOISE

LOW THERMAL RESISTANCE
BL

HIGH SWITCHING CAPABILITY

Color Band
Denotes
Cathode

LOW FORWARD VOLTAGE DROP

MECHANICAL DATA

LL
Case: JEDEC DO-41 molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Solderability: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym

Polarity: Color band denotes cathode

Maximum
In
mm

BL

0.160

4.1

0.205

5.2

Mounting Position: Any

BD

0.103

2.6

0.107

2.7

Weight: 0.013 Ounces (0.35 Grams)

LL
LD

1.00
0.028

25.4
0.71

0.034

0.86

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

SPR21 SPR22 SPR23 UFR24 UFR26 UFR28

Maximum DC Blocking Voltage

VRM

100

200

300

400

600

800

Maximum RMS Voltage

VRMS

70

140

210

280

420

560

VRRM

100

200

300

400

600

800

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ TA = 55 C

IO

Peak Forward Surge Current ( 8.3mS single half sine wave

superimposed on rated load)
Maximum Forward Voltage at 2 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Ambient
Typical Junction Capacitance (Note 1)
Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)
Junction Operating and Storage Temperature Range
NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

IFSM

50

VFM

1.0

@ TC = 25 C
o
@ TC = 100 C

VOLTS

AMPS

70
1.5

VOLTS

IRM

2.0
50

RJA

40

C/W

CJ

60

pF

TRR
TJ, TSTG

35

50
-65 to +150

75

nSec
C
4.97fsesa2

C5

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-200-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

2 AMP SUPER EFFICIENT RECTIFIERS/ULTRAFAST RECOVERY DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES SPR21 - SPR23 and SERIES UFR24 - UFR28
100

Resistive and Inductive Loads

80

60

NOTE 1
40

UFR24-28
SPR21-23

20

NOTE 2
0

Ambient Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10
100

SPR21-23

TJ = 150 oC

1.0

10
TJ = 100 oC
1.0

0.1

UFR24-28

0.1
TJ = 25 oC

0.01
0.01
0

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

0.001

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

Instantaneous Forward Voltage (Volts)
FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

150

120

NOTES
(1) Single Phase, Half Wave, 60 Hz; Lead Length = 0.375" (9.5mm)

90

NOTE 4

(2) JEDEC Method, 8.3 mSec. Single Half Sine Wave;

60

(3) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

30

(4) TJ =25 C, f = 1.0 MHz,

0
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

C6

4.97bsesa2

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-300-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-27 PACKAGE

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

SERIES SPR30 - SPR34

DO - 27

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

LOW SWITCHING NOISE

LOW THERMAL RESISTANCE
BL

HIGH SWITCHING CAPABILITY

Color Band
Denotes
Cathode

LOW FORWARD VOLTAGE DROP

MECHANICAL DATA

LL
Case: JEDEC DO-27 molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Solderability: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym
Polarity: Color band denotes cathode

Maximum
In
mm
9.28
0.365

BL

Mounting Position: Any

BD

Weight: 0.04 Ounces (1.12 Grams)

LL
LD

1.00
0.048

25.4
1.2

0.205

5.2

0.052

1.3

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

SPR30

SPR31

SPR32

UNITS
SPR33

SPR34

Maximum DC Blocking Voltage

VRM

50

100

200

300

400

Maximum RMS Voltage

VRMS

35

70

140

210

280

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

300

400

Average Forward Rectified Current @ TA = 55 oC

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 3 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Ambient

Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)

Junction Operating and Storage Temperature Range
NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

IFSM

75

VFM
o

@ TC = 25 C
o
@ TC = 100 C

Typical Junction Capacitance (Note 1)

IO

1.0

VOLTS

AMPS
1.25

VOLTS

IRM

5.0
50

RJA

20

C/W

CJ

100

pF

TRR

35

nSec

TJ, TSTG

-65 to +150

C
4.97fsesa3

C7

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-300-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

3 AMP SUPER EFFICIENT RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SPR30 - SPR34
150

Resistive and Inductive Loads

125

100

NOTE 1

75

NOTE 2
50

Ambient Temperature, C

25
10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
100
100
TJ = 175 oC

TJ = 150 oC

10

10
TJ = 100 oC
1.0

1.0

TJ = 25 oC

0.1

0.1
0.01
20

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

0.01

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

Instantaneous Forward Voltage (Volts)
FIGURE 3. TYPICAL FORWARD CHARACTERISTICS
250

200

NOTES
(1) Single Phase, Half Wave, 60 Hz; Lead Length = 0.375" (9.5mm)

150

NOTE 4

(2) JEDEC Method, 8.3 mSec. Single Half Sine Wave; TA =55 oC

100

(3) TJ = 25 oC, Pulse Width = 300 Sec, 1.0% Duty Cycle

50

(4) TJ =25 oC, f = 1.0 MHz, VSIG = 50 mV P-P

0
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

C8

4.97bsesa3

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-301-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-27 PACKAGE

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

SERIES UFR300 - UFR310

DO - 27

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

LOW SWITCHING NOISE

LOW THERMAL RESISTANCE
BL

HIGH SWITCHING CAPABILITY

Color Band
Denotes
Cathode

LOW FORWARD VOLTAGE DROP

MECHANICAL DATA

LL
Case: JEDEC DO-27 molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Solderability: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym
Polarity: Color band denotes cathode

BL
Mounting Position: Any

BD

Weight: 0.04 Ounces (1.12 Grams)

LL
LD

1.00
0.048

25.4
1.2

Maximum
In
mm
9.28
0.365
0.205

5.2

0.052

1.3

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

SYMBOL

RATINGS

Maximum DC Blocking Voltage

VRM

UFR UFR UFR UFR UFR UFR UFR UFR UFR

300 301 302 303 304 305 306 308 310
50 100 200 300 400 500 600 800 1000

Maximum RMS Voltage

VRMS

35

70 140 210 280 350

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100 200 300 400 500

Series Number

Average Forward Rectified Current @ TA = 55 oC

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 3 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Lead

IO

IFSM

160

VFM

1.25

@ TC = 25 C
o
@ TC = 125 C

UNITS

420 560

700 VOLTS

600 800 1000

AMPS
1.7

VOLTS

IRM

5
50

RJA

20

C/W

Typical Junction Capacitance (Note 1)

CJ

45

pF

Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)

TRR

Junction Operating and Storage Temperature Range

NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

TJ, TSTG

75

50
-65 to +150

nSec
C
3.01 ufr300

C9

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-301-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

3 AMP ULTRAFAST RECOVERY DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES UFR300 - UFR310
175

Resistive and Inductive Loads

160
150

125

NOTE 1
100

75

50

Ambient Temperature, oC

25
10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
100
100

TJ = 150 oC

10

10

UFR300-304

TJ = 100 oC

1.0

TJ = 25 oC

1.0

0.1
UFR305-310

0.1
0.01
0

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

0.01

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

Instantaneous Forward Voltage (Volts)
FIGURE 3. TYPICAL FORWARD CHARACTERISTICS
200

160

NOTES
(1) Single Phase, Half Wave, 60 Hz; Lead Length = 0.375" (9.5mm)

120
UFR306-310

(2) JEDEC Method, 8.3 mSec. Single Half Sine Wave;

80
UFR300-305

(3) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

40

0
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

C10

4.97bsesa3a

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-401-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-27 PACKAGE

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

SERIES UFR400 - UFR410

DO - 27

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

LOW SWITCHING NOISE

LOW THERMAL RESISTANCE
BL

HIGH SWITCHING CAPABILITY

Color Band
Denotes
Cathode

LOW FORWARD VOLTAGE DROP

MECHANICAL DATA

LL
Case: JEDEC DO-27 molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads
LD (Dia)
Solderability: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym
Polarity: Color band denotes cathode

BL
Mounting Position: Any

BD

Weight: 0.04 Ounces (1.12 Grams)

LL
LD

1.00
0.048

25.4
1.2

Maximum
In
mm
9.28
0.365
0.205

5.2

0.052

1.3

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

UFR UFR UFR UFR UFR UFR UFR UFR UFR

400 401 402 403 404 406 408 409 410

Series Number
Maximum DC Blocking Voltage

VRM

50

Maximum RMS Voltage

VRMS

35

70

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100 200 300 400 600

Average Forward Rectified Current @ TA = (as shown)

IO

Peak Forward Surge Current ( 8.3mS single half sine wave

superimposed on rated load)
3-Amps DC
Maximum Forward Voltage at:
4-Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance:

UNITS

Maximum Reverse Recovery Time (IF=0.5A, I R=1A, I RR=0.25A)

Junction Operating and Storage Temperature Range
NOTES: (1) Measured at 1MHz and an applied reverse voltage of 4 volts.

140 210 280 420

4
@TA=80oC

IFSM

IRM
RJL
RJA

1.70
1.85
10
50
7.5
18.0

CJ

TJ, TSTG

560 630

700

VOLTS

800 900 1000

4 o
@TA=55 C

1.20
1.25
5
50

VFM

TRR

800 900 1000

AMPS

200

@ TJ = 25 C
@ TJ = 125 oC
Junction to Lead
Junction to Air

Typical Junction Capacitance (Note 1)

100 200 300 400 600

60
-65 to +175

A
C/W
pF

45
50

VOLTS

75

nSec
C
3.01 ufr400

C11

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-401-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

4 AMP ULTRAFAST RECOVERY DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES UFR400 - UFR410

250

Resistive and Inductive Loads

200
UFR400-404
150

100

UFR406-410

50

NOTE 1

NOTE 2
0
1

10

100

Ambient Temperature, C

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100

500
(2)
TJ = 175 oC

(1) UFR400-404
(2) UFR406-410

100
(1)
TJ = 175 oC

10
10
(2)
(1)

1.0
1.0
(2)
TJ = 25 oC
0.1

0.1

(1)
TJ = 25 oC
(1) UFR400-404
(2) UFR406-410

0.01

0.01

0.005
0

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

100

NOTES
(1) Lead Length = 0.375" (9.5mm)
(2)

(2) JEDEC Method, 8.3 mSec. Single Half Sine Wave

(1)
10

(3) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

(4) These Curves Are Typical For The Highest Voltage Diode
in The Voltage Grouping.

(1) UFR400-404
(2) UFR406-410

10

20

30

40

50

Reverse Voltage, (Volts)

C12

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

3.01 ufr400

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-500-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

ACTUAL SIZE OF
DO-27 PACKAGE

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

SERIES SPR51 - SPR54

DO - 27

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

LOW SWITCHING NOISE

LOW THERMAL RESISTANCE
HIGH SWITCHING CAPABILITY

BL
Color Band
Denotes
Cathode

LOW FORWARD VOLTAGE DROP

MECHANICAL DATA

LL
Case: JEDEC DO-27 molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads
LD (Dia)
Solderability: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym
Polarity: Color band denotes cathode

BL
Mounting Position: Any

BD

Weight: 0.04 Ounces (1.12 Grams)

LL
LD

1.00
0.048

25.4
1.2

Maximum
In
mm
9.28
0.365
0.205

5.2

0.052

1.3

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

SPR51

SPR52

SPR53

SPR54

Maximum DC Blocking Voltage

VRM

100

200

300

400

Maximum RMS Voltage

VRMS

70

140

210

280

Maximum Peak Recurrent Reverse Voltage

VRRM

100

200

300

400

Average Forward Rectified Current @ TA = 55 o C

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 5 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Ambient
Typical Junction Capacitance (Note 1)
Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)
Junction Operating and Storage Temperature Range
NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

IO

IFSM

150

VFM

1.25

VOLTS

IRM

5
50

RJA

20

C/W

CJ

75

pF

TRR

50

nSec

TJ, TSTG

-65 to +150

@ TC = 25 C
o
@ TC = 100 C

VOLTS

AMPS

4.97fsesa5

C13

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-500-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

5 AMP SUPER EFFICIENT RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SPR51 - SPR54
150

Resistive and Inductive Loads

120

SPR51-53

90

NOTE 1
SPR54

60

30

NOTE 2
o

Ambient Temperature, C

10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
100
SPR51-53

TJ = 150 oC

10

10
TJ = 100 oC

SPR54

1.0

1.0

TJ = 25 oC
0.1

0.1
0.01
0

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

0.01

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

Instantaneous Forward Voltage (Volts)
FIGURE 3. TYPICAL FORWARD CHARACTERISTICS
300

250

NOTES

200

(1) Single Phase, Half Wave, 60 Hz; Lead Length = 0.375" (9.5mm)
(2) JEDEC Method, 8.3 mSec. Single Half Sine Wave; TL = 55 o C

150

(3) TJ = 25 oC, Pulse Width = 300 Sec, 1.0% Duty Cycle

100

(4) TJ = 25 oC, f = 1 MHz, VSIG = 50 mV P-P

50
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

C14

4.97bsesa5

DIOTEC ELECTRONICS CORP

Data Sheet No. SESA-600-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
Low switching noise

ACTUAL SIZE OF
UFR600 PACKAGE

SERIES UFR600 - UFR608

Low forward voltage drop

Low thermal resistance

LL
BD (Dia)

High switching capability

High surge capability

BL

Color Band
Denotes
Cathode

High reliability

MECHANICAL DATA
LL
Case: Molded epoxy (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Solderability: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym

Polarity: Color band denotes cathode

BL
Mounting Position: Any

BD

Weight: 0.07 Ounces (2.1 Grams)

LL
LD

Maximum
In
mm

8.6

0.360

9.1

0.340

8.6

0.360

9.1

1.00
0.048

25.4
1.2

0.052

1.3

0.340

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Maximum DC Blocking Voltage

VRM

50

100

UFR
602
200

600

800

Maximum RMS Voltage

VRMS

35

70

140

210

280

420

560

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

300

400

600

800

Series Number

Average Forward Rectified Current @ TA = 55 oC

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 6 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Case

Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)

Junction Operating and Storage Temperature Range
NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

UFR
601

UFR
603
300

UFR
604
400

UFR
606

UFR
608

IO

IFSM

300

VFM

VOLTS

AMPS

1.25

@ TC = 25 C
o
@ TC = 100 C

Typical Junction Capacitance (Note 1)

UFR
600

UNITS

1.4

VOLTS

IRM

10
200

RJC

10

C/W

CJ

100

pF

TRR
TJ, TSTG

60

75
-65 to +150

90

nSec
C
01.00 fsesa6

C15

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-600-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

6 AMP ULTRAFAST RECOVERY DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES UFR600 - UFR608
150

Resistive and Inductive Loads

120

NOTE 1
90
Ground Plane
PC Board With
1" x 1" Copper
Surface Area

60

Standard PC Board
Mounting
(Recommended Method)

30

NOTE 2
o

Ambient Temperature, C

10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
100
TJ = 150 oC

10

10
TJ = 100 oC

1.0

1.0

TJ = 25 oC
0.1

0.1
0.01
0.6

1.0

1.2

1.4

1.6

1.8

Percent of Rated Peak Reverse Voltage

0.01

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

Instantaneous Forward Voltage (Volts)
FIGURE 3. TYPICAL FORWARD CHARACTERISTICS
250

200

NOTES
(1) Single Phase, Half Wave, 60 Hz

150

(2) JEDEC Method, 8.3 mSec. Single Half Sine Wave;

100

(3) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

50

(4) TJ = 25 C, f = 1 MHz, VSIG = 50 mV P-P

0
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

C16

4.97bsesa6

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-601-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
TO-220AC PACKAGE

Glass Passivated for high reliability/temperature performance

FULLY INSULATED PACKAGE

Low switching noise

Low forward voltage drop

DT 8G
6SPR03

A1

D4
D1

Low thermal resistance

DT 8G
High switching capability

6SPR03

B4

High surge capability

B3
3

MECHANICAL DATA

A
A1
A2
B
B1
B2
B3
B4
C
D
D1
D2
D3
D4

D3

Minimum
mm
in

Sym

Case: TO-220 molded plastic (Fully Insulated)

(U/L Flammability Rating 94V-0)

Maximum
in
mm
0.187 4.75

B1

4.75*
3.56*
0.043 1.1
0.9
0.102 2.6
2.3
0.64*
1.27*
0.04
1.0
0.413 10.5
0.61 15.5
0.59 15.0
0.262* 6.6*
0.16
4.0
0.54 13.7
0.60 15.2
0.108* 2.75*
P 0.126* 3.2*
* These dimensions are "Typicals".

Terminals: Rectangular pins w/ standoff

Solderability: Per MIL-STD 202 Method 208 guaranteed
Polarity: Diode depicted on product
Mounting Position: Any
Weight: 0.06 Ounces (1.7 Grams)

D2

B
B1

0.121*
0.14*
0.035
0.09
0.025*
0.050*

B2
A2

ITO - 220AC
SERIES 6SPR01 - 6SPR05

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL
6SPR01 6SPR02

Series Number

UNITS

6SPR03

6SPR04

6SPR05

Maximum DC Blocking Voltage

VRM

100

200

300

400

500

Maximum RMS Voltage

VRMS

70

140

210

280

350

VRRM

100

200

300

400

500

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ Tc = 100 C

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 6 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Case

IFSM

80

VFM

@ TC = 25 C
o
@ TC = 100 C

Maximum Reverse Recovery Time (IF=6.0A, di/dt=50A/S,TJ=25 C)

o

NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

1.05

Typical Junction Capacitance (Note 1)

Junction Operating and Storage Temperature Range

IO

VOLTS

AMPS
1.3

VOLTS

IRM

10
500

RJC

C/W

CJ

65

pF

TRR
TJ, TSTG

45

35
-65 to +150

nSec
C
4.97fsesa6a

C17

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-601-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

6 AMP SUPER EFFICIENT RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES 6SPR01 - 6SPR05
100

Resistive and Inductive Loads

80

60

40

NOTE 1
20

Case Temperature, oC

10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

1000

100

TC = 100 oC
100

10

6SPR01-02

10

1.0
1.0

6SPR03-05

TC = 25 oC

0.1

0.1

20

Instantaneous Forward Voltage (Volts)

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

100

80

NOTES

60

(1) JEDEC Method, 8.3 mSec. Single Half Sine Wave

40

(2) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

(3) TC = 25 o C, f = 1 MHz, VSIG = 50 mV P-P

20

0
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

C18

4.97bsesa6a

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-801-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1054 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
TO-220AC PACKAGE

Glass Passivated for high reliability/temperature performance

FULLY INSULATED PACKAGE

Low switching noise

Low forward voltage drop

DT 5B
8SPR05

A1

D4
D1

Low thermal resistance

High switching capability

DT 5B
8SPR05

B4

High surge capability

B3
3

MECHANICAL DATA

A
A1
A2
B
B1
B2
B3
B4
C
D
D1
D2
D3
D4

D3

Minimum
mm
in

Sym

Case: TO-220 molded plastic (Fully Insulated)

(U/L Flammability Rating 94V-0)

Maximum
in
mm
0.187 4.75

B1

4.75*
3.56*
0.043 1.1
0.9
0.102 2.6
2.3
0.64*
1.27*
0.04
1.0
0.413 10.5
0.61 15.5
0.59 15.0
0.262* 6.6*
0.16
4.0
0.54 13.7
0.60 15.2
0.108* 2.75*
P 0.126* 3.2*
* These dimensions are "Typicals".

Terminals: Rectangular pins w/ standoff

Solderability: Per MIL-STD 202 Method 208 guaranteed
Polarity: Diode depicted on product
Mounting Position: Any
Weight: 0.06 Ounces (1.7 Grams)

D2

B
B1

0.121*
0.14*
0.035
0.09
0.025*
0.050*

B2
A2

ITO - 220AC
SERIES 8SPR01 - 8SPR05

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL
8SPR01 8SPR02

Series Number

UNITS

8SPR03

8SPR04

8SPR05

Maximum DC Blocking Voltage

VRM

100

200

300

400

500

Maximum RMS Voltage

VRMS

70

140

210

280

350

VRRM

100

200

300

400

500

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ Tc = 110 C

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 8 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Case

IFSM

120

VFM

@ TC = 25 C
o
@ TC = 100 C

Maximum Reverse Recovery Time (IF=8.0A, di/dt=50A/S, TJ=25 C)

o

NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

1.0

Typical Junction Capacitance (Note )

Junction Operating and Storage Temperature Range

IO

VOLTS

AMPS
1.2

VOLTS

RJC

10
500
1.5

C/W

CJ

45

pF

IRM

TRR
TJ, TSTG

45

35
-65 to +150

nSec
C
4.97fsesa8

C19

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-801-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

8 AMP SUPER EFFICIENT RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES 8SPR01 - 8SPR05
125

Resistive and Inductive Loads

100

75

50

NOTE 1
25

Case Temperature, oC

10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

1000

100

TC = 100 oC
100

8SPR01-02

10

10

1.0
1.0

TC = 25 oC

8SPR03-05

0.1

0.1

20

Instantaneous Forward Voltage (Volts)

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

60

50

NOTES

40

(1) JEDEC Method, 8.3 mSec. Single Half Sine Wave

30

(2) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

(3) TC = 25 o C, f = 1 MHz, VSIG = 50 mV P-P

20

0
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

C20

4.97bsesa8

DIOTEC ELECTRONICS C0RP.

Data Sheet No. SESA-802-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-11052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
TO-220AC PACKAGE

Glass Passivated for high reliability/temperature performance

NON - INSULATED
PACKAGE

Low switching noise

Low forward voltage drop

DT 4O
SPR84

A
A1

D4
D1

Low thermal resistance

High switching capability

DT 4O
SPR84

B4

High surge capability

B3
3

MECHANICAL DATA

A
A1
A2
B
B1
B2
B3
B4
C
D
D1
D2
D3
D4

D3

Minimum
mm
in

Sym

Case: TO-220 molded plastic (U/L Flammability Rating 94V-0)

Maximum
in
mm
0.187 4.75

B1

4.75*
3.56*
0.043 1.1
0.9
0.102 2.6
2.3
0.64*
1.27*
0.04
1.0
0.413 10.5
0.61 15.5
0.59 15.0
0.262* 6.6*
0.16
4.0
0.54 13.7
0.60 15.2
0.108* 2.75*
P 0.126* 3.2*
* These dimensions are "Typicals".

Terminals: Rectangular pins w/ standoff

Solderability: Per MIL-STD 202 Method 208 guaranteed
Polarity: Diode depicted on product
Mounting Position: Any
Weight: 0.08 Ounces (2.2 Grams)

D2

B
B1

0.121*
0.14*
0.035
0.09
0.025*
0.050*

B2
A2

TO - 220AC
SERIES SPR81 - SPR86

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

UNITS

SPR81 SPR82 SPR83 SPR84 SPR85 SPR86

Series Number
Maximum DC Blocking Voltage

VRM

100

200

300

400

500

600

Maximum RMS Voltage

VRMS

70

140

210

280

350

420

VRRM

100

200

300

400

500

600

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ Tc = 110 C

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 8 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Case

Maximum Reverse Recovery Time (IF=0.5A, IR=1.0A, IRR=0.25A)

Junction Operating and Storage Temperature Range
NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

IFSM

125

VFM

1.0

@ TC = 25 C
o
@ TC = 100 C

Typical Junction Capacitance (Note 1)

IO

VOLTS

AMPS
1.2

VOLTS

IRM

10
500

RJC

C/W

CJ

65

pF

TRR
TJ, TSTG

45

35
-65 to +150

nSec
C
4.97fsesa8a

C21

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-802-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

8 AMP SUPER EFFICIENT RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SPR81 - SPR86
150

Resistive and Inductive Loads

120

90

60

NOTE 1
30

Case Temperature, oC

10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

1000

100

TC = 100 oC
100

SPR81-83

10

10

1.0
1.0

TC = 25 oC

SPR84-86

0.1

0.1

Instantaneous Forward Voltage (Volts)

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

80

70

NOTES

60

(1) JEDEC Method, 8.3 mSec. Single Half Sine Wave

50

(2) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

(3) TC = 25 o C, f = 1 MHz, VSIG = 50 mV P-P

40

30
1

10

100

1000

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

C22

4.97bsesa8a

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-1201-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
TO-220AC PACKAGE

Glass Passivated for high reliability/temperature performance

FULLY INSULATED PACKAGE

Low switching noise

Low forward voltage drop

DT 4A
12SPRO4

A
A1

D4
D1

Low thermal resistance

High switching capability

DT 4A
12SPRO4

B4

High surge capability

B3
3

MECHANICAL DATA

A
A1
A2
B
B1
B2
B3
B4
C
D
D1
D2
D3
D4

D3

Minimum
mm
in

Sym

Case: TO-220 molded plastic (Full Insulated)

(U/L Flammability Rating 94V-0)

Maximum
in
mm
0.187 4.75

B1

4.75*
3.56*
0.043 1.1
0.9
0.102 2.6
2.3
0.64*
1.27*
0.04
1.0
0.413 10.5
0.61 15.5
0.59 15.0
0.262* 6.6*
0.16
4.0
0.54 13.7
0.60 15.2
0.108* 2.75*
P 0.126* 3.2*
* These dimensions are "Typicals".

Terminals: Rectangular pins w/ standoff

Solderability: Per MIL-STD 202 Method 208 guaranteed
Polarity: Diode depicted on product
Mounting Position: Any
Weight: 0.06 Ounces (1.7 Grams)

D2

B
B1

0.121*
0.14*
0.035
0.09
0.025*
0.050*

B2
A2

ITO - 220AC
SERIES 12SPR01 - 12SPR05

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

UNITS

12SPR01 12SPR02 12SPR03 12SPR04 12SPR05

Series Number
Maximum DC Blocking Voltage

VRM

100

200

300

400

500

Maximum RMS Voltage

VRMS

70

140

210

280

350

Maximum Peak Recurrent Reverse Voltage

VRRM

100

200

300

400

500

Average Forward Rectified Current @ Tc = 110 oC

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 12 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Case

IFSM

120

VFM

@ TC = 25 C
o
@ TC = 100 C

Maximum Reverse Recovery Time (IF=8.0A, di/dt=50A/S,TJ=25 C)

o

NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

12

1.05

Typical Junction Capacitance (Note 1)

Junction Operating and Storage Temperature Range

IO

VOLTS

AMPS
1.20

VOLTS

IRM

10
500

RJC

1.5

C/W

CJ

45

pF

TRR
TJ, TSTG

45

35
-65 to +150

nSec
C
4.97fsesa12

C23

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-1201-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

12 AMP SUPER EFFICIENT RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES 12SPR001 - 12SPR05
150

Resistive and Inductive Loads

120

90

60

NOTE 1
30

Case Temperature, oC

10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

1000

100

TC = 100 oC
100

12SPR01-03

10

10

1.0
1.0

TC = 25 oC

12SPR04-05

0.1

0.1

Instantaneous Forward Voltage (Volts)

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

80

70

NOTES

60

(1) JEDEC Method, 8.3 mSec. Single Half Sine Wave

50

(2) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

(3) TC = 25 o C, f = 1 MHz, VSIG = 50 mV P-P

40

30
1

10

100

1000

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

C24

4.97bsesa12

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-1502-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
Glass Passivated for high reliability/temperature performance

ACTUAL SIZE OF
TO-220AC PACKAGE

NON - INSULATED
PACKAGE

Low switching noise

Low forward voltage drop

DT 7D
SPR155

A
A1

D4
D1

Low thermal resistance

DT 7D
SPR155

High switching capability

B4

High surge capability

B3
3

MECHANICAL DATA

A
A1
A2
B
B1
B2
B3
B4
C
D
D1
D2
D3
D4

D3

Minimum
mm
in

Sym

Case: TO-220 molded plastic (U/L Flammability Rating 94V-0)

Maximum
in
mm
0.187 4.75

B1

4.75*
3.56*
0.043 1.1
0.9
0.102 2.6
2.3
0.64*
1.27*
0.04
1.0
0.413 10.5
0.61 15.5
0.59 15.0
0.262* 6.6*
0.16
4.0
0.54 13.7
0.60 15.2
0.108* 2.75*
P 0.126* 3.2*
* These dimensions are "Typicals".

Terminals: Rectangular pins w/ standoff

Solderability: Per MIL-STD 202 Method 208 guaranteed
Polarity: Diode depicted on product
Mounting Position: Any
Weight: 0.08 Ounces (2.2 Grams)

D2

B2

B
B1

0.121*
0.14*
0.035
0.09
0.025*
0.050*

A2

TO - 220AC
SERIES SPR150 - SPR156

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

SPR
150

SPR
151

SPR
152

SPR
153

SPR
154

SPR
155

SPR
156

Maximum DC Blocking Voltage

VRM

50

100

200

300

400

500

600

Maximum RMS Voltage

VRMS

35

70

140

210

280

350

420

VRRM

50

100

200

300

400

500

600

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ Tc = 110 C

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 15 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Case

Maximum Reverse Recovery Time (IF=0.5A, IR=1.0A, IRR=0.25A)

Junction Operating and Storage Temperature Range
NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

15

IFSM

250

VFM

0.95

AMPS

1.25

@ TC = 25 C
o
@ TC = 100 C

Typical Junction Capacitance (Note 1)

IO

VOLTS

1.5

VOLTS

IRM

10
500

RJC

1.5

C/W

CJ

65

pF

TRR
TJ, TSTG

50

35
-65 to +150

nSec
C
4.97fsesa15

C25

DIOTEC ELECTRONICS CORP.

Data Sheet No. SESA-1502-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

15 AMP SUPER EFFICIENT RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SPR150 - SPR156
250

Resistive and Inductive Loads

200

150

100

NOTE 1
50

Case Temperature, oC

10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

1000

100

TC = 100 oC
100

SPR150-152

10

10

1.0
TC = 25 oC

1.0
SPR153-156

0.1

0.1

Instantaneous Forward Voltage (Volts)

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

80

70

NOTES

60

(1) JEDEC Method, 8.3 mSec. Single Half Sine Wave

50

(2) TJ = 25 oC, Pulse Width = 300 Sec, 1.0% Duty Cycle

(3) TC = 25 o C, f = 1 MHz, VSIG = 50 mV P-P

40

30
1

10

100

1000

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

C26

4.97bsesa15

SECTION D
SUPER EFFICIENT and
ULTRA FAST RECOVERY
RECTIFIERS
Dual Diode Products

DT 1A
SPR1002C

DT 7D
UFR3002C

3 PIN TO-220AB AND TO-247AB PACKAGES

6 TO 30 AMPERES
TO - 220AB

100 TO 600 VOLTS

DIOTEC ELECTRONICS CORP.

TO - 247AB

- 18020 Hobart Blvd., Unit B - Gardena, CA 90248 U.S.A. - PH: 310-767-1052 - FX: 310-767-7958

DIOTEC ELECTRONICS CORP.

Data Sheet No. SEDR-600-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
TO-220AB PACKAGE

Glass Passivated for high reliability/temperature performance

FULLY INSULATED PACKAGE

Low switching noise

Low forward voltage drop

DT 1A
SPR603C

A1

D4

Low thermal resistance

D1

High switching capability

DT 1A
SPR603C

2
High surge capability

MECHANICAL DATA

D2

B3
3

Case: TO-220 molded plastic (Fully Insulated)

(U/L Flammability Rating 94V-0)

Sym
A
A1
A2
B
B1
B2
B3
C
D
D1
D2
D3
D4

Terminals: Rectangular pins w/ standoff

Minimum
mm
in

D3

Maximum
mm
in
0.187 4.75

1.4*
3.56*
0.9
0.043 1.1
0.102 2.6
2.3
0.66*
1.3*
0.410 10.4
0.59 15.0
0.61 15.5
0.25*
6.4*
0.16
4.0
0.53 13.5
0.57 14.8
0.108* 2.75*
P 0.141* 3.58*
* These dimensions are "Typicals".

Solderability: Per MIL-STD 202 Method 208 guaranteed

Polarity: Diodes depicted on product
Mounting Position: Any
Weight: 0.06 Ounces (1.75 Grams)

0.055*
0.14*
0.035
0.09
0.028*
0.051*

B1

B2

A2

B1

ITO - 220AB
SERIES SPR601C - SPR605C

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

SPR
601C

SPR
602C

SPR
603C

SPR
604C

SPR
605C

Maximum DC Blocking Voltage

VRM

100

200

300

400

500

Maximum RMS Voltage

VRMS

70

140

210

280

350

VRRM

100

200

300

400

500

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ Tc = 120 C

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage (per diode) at 3 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Case

IFSM

60

VFM

@ TC = 25 C
o
@ TC = 100 C

Maximum Reverse Recovery Time (IF=3.0A, di/dt=50A/S,TJ=25 C)

o

NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

Typical Junction Capacitance (Note 1)

Junction Operating and Storage Temperature Range

IO

1.0

VOLTS

AMPS
1.25

VOLTS

IRM

10
500

RJC

C/W

CJ

65

pF

TRR

30

nSec

TJ, TSTG

-65 to +150

C
4.97fsedr6

D1

DIOTEC ELECTRONICS CORP.

Data Sheet No. SEDR-600-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

6 AMP SUPER EFFICIENT RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SPR601C - SPR605C
75

Resistive and Inductive Loads

60

45

30

NOTE 1
15

0
1

Case Temperature, oC

10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10

100

TC = 100 oC
1.0

SPR601C-602C

10

0.1

1.0
0.01

TC = 25 oC

SPR603C-605C
0.001

0.1

Instantaneous Forward Voltage (Volts)

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

80

70

NOTES

60

(1) JEDEC Method, 8.3 mSec. Single Half Sine Wave

50

(2) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

(3) TC = 25 o C

40

30
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

D2

4.97bsedr6

DIOTEC ELECTRONICS CORP

Data Sheet No. SEDR-1000-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
TO-220AB PACKAGE

Glass Passivated for high reliability/temperature performance

FULLY INSULATED PACKAGE

Low switching noise

Low forward voltage drop

DT 1A
SPR1002C

A1

D4

Low thermal resistance

D1

High switching capability

DT 1A
SPR1002C

2
High surge capability

MECHANICAL DATA

D2

B3
3

Case: TO-220 molded plastic (Fully Insulated)

(U/L Flammability Rating 94V-0)

Sym
A
A1
A2
B
B1
B2
B3
C
D
D1
D2
D3
D4

Terminals: Rectangular pins w/ standoff

Minimum
mm
in

D3

Maximum
mm
in
0.187 4.75

1.4*
3.56*
0.9
0.043 1.1
0.102 2.6
2.3
0.66*
1.3*
0.410 10.4
0.59 15.0
0.61 15.5
0.25*
6.4*
0.16
4.0
0.53 13.5
0.57 14.8
0.108* 2.75*
P 0.141* 3.58*
* These dimensions are "Typicals".

Solderability: Per MIL-STD 202 Method 208 guaranteed

Polarity: Diodes depicted on product
Mounting Position: Any
Weight: 0.06 Ounces (1.75 Grams)

0.055*
0.14*
0.035
0.09
0.028*
0.051*

B1

B2
A2

B1

ITO - 220AB
SERIES SPR1001C - SPR1005C

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

SPR
1001C

SPR
1002C

SPR
1003C

SPR
1004C

SPR
1005C

Maximum DC Blocking Voltage

VRM

100

200

300

400

500

Maximum RMS Voltage

VRMS

70

140

210

280

350

VRRM

100

200

300

400

500

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ Tc = 120 C

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage (per diode) at 5 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Case

IFSM

100

VFM

@ TC = 25 C
o
@ TC = 100 C

Maximum Reverse Recovery Time (IF=5.0A, di/dt=50A/S,TJ=25 C)

o

NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

10

1.0

Typical Junction Capacitance (Note 1)

Junction Operating and Storage Temperature Range

IO

VOLTS

AMPS
1.25

VOLTS

IRM

10
500

RJC

C/W

CJ

65

pF

TRR
TJ, TSTG

45

35
-65 to +150

nSec
C
4.97fsedr10

D3

DIOTEC ELECTRONICS CORP.

Data Sheet No. SEDR-1000-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

10 AMP SUPER EFFICIENT RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SPR1001C - SPR1005C
100

80

60

Resistive and Inductive Loads

40

NOTE 1
20

0
10

100

Case Temperature, C

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10

100

TC = 100 oC
1.0

SPR1001C-1002C

10

0.1

1.0
0.01

TC = 25 oC

SPR1003C-1005C
0.001

0.1

Instantaneous Forward Voltage (Volts)

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

80

70

NOTES

60

(1) JEDEC Method, 8.3 mSec. Single Half Sine Wave

50

(2) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

(3) TJ = 25 oC

40

30
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

D4

4.97bsedr10

DIOTEC ELECTRONICS CORP.

Data Sheet No. SEDR-1600-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
TO-220AB PACKAGE

Glass Passivated for high reliability/temperature performance

FULLY INSULATED PACKAGE

Low switching noise

A
Low forward voltage drop

DT 1A
SPR1604C

Low thermal resistance

A1

D4
D1

High switching capability

D

DT 1A
SPR1604C

High surge capability

MECHANICAL DATA
B3
3

Case: TO-220 molded plastic- Fully Insulated

(U/L Flammability Rating 94V-0)

Minimum
mm
in

Sym
A
A1
A2
B
B1
B2
B3
C
D
D1
D2
D3
D4

Terminals: Rectangular pins w/ standoff

D3

Maximum
mm
in
0.187 4.75

1.4*
3.56*
0.9
0.043 1.1
2.3
0.102 2.6
0.66*
1.3*
0.410 10.4
0.61 15.5
0.59 15.0
6.4*
0.25*
0.16
4.0
0.53 13.5
0.57 14.8
0.108* 2.75*
P 0.141* 3.58*
* These dimensions are "Typicals".

Solderability: Per MIL-STD 202 Method 208 guaranteed

Polarity: Diodes depicted on product
Mounting Position: Any
Weight: 0.08 Ounces (2.2 Grams)

D2

0.055*
0.14*
0.035
0.09
0.028*
0.051*

B1

B2

A2

B1

TO - 220AB
SERIES SPR1601C - SPR1605C

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

SPR
1601C

SPR
1602C

SPR
1603C

SPR
1604C

SPR
1605C

Maximum DC Blocking Voltage

VRM

100

200

300

400

500

Maximum RMS Voltage

VRMS

70

140

210

280

350

VRRM

100

200

300

400

500

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ Tc = 100 C

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage (per diode) at 8 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Case

IFSM

150

VFM

@ TC = 25 C
@ TC = 100 o C

Maximum Reverse Recovery Time (IF=8.0A, di/dt=50A/S,TJ=25oC)

NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

16

1.0

Typical Junction Capacitance (Note 1)

Junction Operating and Storage Temperature Range

IO

VOLTS

AMPS
1.2

VOLTS

IRM

10
500

RJC

C/W

CJ
TRR
TJ, TSTG

pF

65
35

45
-65 to +150

nSec
C
7.99SPR1601C

D5

DIOTEC ELECTRONICS CORP.

Data Sheet No. SEDR-1600C-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

16 AMP SUPER EFFICIENT RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SPR1601C - SPR1605C
150

120

90

60

Resistive and Inductive Loads

NOTE 1
30

0
10

100

Case Temperature, C

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100

10

10

TC = 100 oC

1.0

SPR1601C-1602C

0.1

1.0
0.01

TC = 25 oC

SPR1603C-1605C

0.1
0.001
0

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

80

70

NOTES

60

(1) JEDEC Method, 8.3 mSec. Single Half Sine Wave

50

(2) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

(3) TJ = 25 oC

40

30
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

D6

3.00Bsedr1600c

DIOTEC ELECTRONICS CORP.

Data Sheet No. SEDR-160C-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
TO-220AB PACKAGE

Glass Passivated for high reliability/temperature performance

NON - INSULATED
PACKAGE

Low switching noise

A
Low forward voltage drop

DT 7D
SPR162C

Low thermal resistance

A1

D4
D1

High switching capability

D

DT 7D
SPR162C

High surge capability

MECHANICAL DATA
B3
3

D2

Case: TO-220 molded plastic (U/L Flammability Rating 94V-0)

Minimum
mm
in

Sym

Terminals: Rectangular pins w/ standoff

A
A1
A2
B
B1
B2
B3
C
D
D1
D2
D3
D4

1.4*
3.56*
0.9
0.043 1.1
2.3
0.102 2.6
0.66*
1.3*
0.410 10.4
0.61 15.5
0.59 15.0
6.4*
0.25*
0.16
4.0
0.53 13.5
0.57 14.8
0.108* 2.75*
P 0.141* 3.58*
* These dimensions are "Typicals".

Solderability: Per MIL-STD 202 Method 208 guaranteed

Polarity: Diodes depicted on product
Mounting Position: Any
Weight: 0.08 Ounces (2.2 Grams)

D3

Maximum
mm
in
0.187 4.75

0.055*
0.14*
0.035
0.09
0.028*
0.051*

B1

B2

A2

B1

TO - 220AB
SERIES SPR161C - SPR166C

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

SPR
161C

SPR
162C

SPR
163C

SPR
164C

SPR
165C

SPR
166C

Maximum DC Blocking Voltage

VRM

100

200

300

400

500

600

Maximum RMS Voltage

VRMS

70

140

210

280

350

420

VRRM

100

200

300

400

500

600

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ Tc = 100 C

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 8 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Case

Maximum Reverse Recovery Time (IF=0.5A, IR=1.0A, IRR=0.25A)

Junction Operating and Storage Temperature Range
NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

16

IFSM

200

VFM

0.975

@ TC = 25 C
o
@ TC = 100 C

Typical Junction Capacitance (Note 1)

IO

VOLTS

AMPS

1.3

1.5

VOLTS

IRM

10
500

RJC

C/W

CJ

65

pF

TRR
TJ, TSTG

50

35
-65 to +150

nSec
C
4.97fsedr16c

D7

DIOTEC ELECTRONICS CORP.

Data Sheet No. SEDR-160C-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

16 AMP SUPER EFFICIENT RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SPR161C - SPR166C
250

200

150

100

Resistive and Inductive Loads

NOTE 1
50

0
10

100

Case Temperature, C

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100

100

TC = 100 oC

10

10

SPR161C-163C

1.0

1.0
0.1

TC = 25 oC

SPR164C-166C

0.1
0.01
0

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

80

70

NOTES

60

(1) JEDEC Method, 8.3 mSec. Single Half Sine Wave

50

(2) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

(3) TJ = 25 oC

40

30
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

D8

4.97bsedr16C

DIOTEC ELECTRONICS CORP

Data Sheet No. SEDR-3000-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF TO-247AB

(TO-3PAB) PACKAGE

Glass Passivated for high reliability/temperature performance

A2

Low switching noise

D1
RO

Low forward voltage drop

DT 7D
UFR3002C

DT 7D
UFR3002C

Low thermal resistance

High switching capability

L1
2

High surge capability

MECHANICAL DATA

B1
1 2

Case: TO-247(TO-3P) molded plastic

(U/L Flammability Rating 94V-0)

Minimum
mm
in
0.19
4.82
0.087 2.21
0.075 1.9
0.045 1.14
0.022 0.56
0.079 2.01
0.116 2.95

Maximum
Sym
mm
in
A
0.205
5.2
0.102
2.6
A1
0.085
2.16
A2
0.055
B
1.4
0.032
0.81
B1
0.094
2.39
B2
B3
0.126
3.2
0.215
5.46
B4
C 0.602 15.29 0.625 15.88
D 0.776 19.7 0.799 20.3
5.69
D1 0.209 5.31 0.224
L 0.559 14.2 0.582 14.8
4.8
L1 0.146 3.71 0.189
RO 0.209
5.3 0.224
5.7
P 0.13
3.3 0.145
3.7

Terminals: Rectangular pins w/ standoff

Solderability: Per MIL-STD 202 Method 208 guaranteed
Polarity: Diodes depicted on product
Mounting Position: Any
Weight: 0.2 Ounces (5.55 Grams)

B2*

A1

B3
B4

B4

*Applies to Pins 1 and 3

TO-247AB (TO-3PAB)
SERIES UFR3001C - UFR3005C

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

UFR
3001C

UFR
3002C

UFR
3003C

UFR
3004C

UFR
3005C

Maximum DC Blocking Voltage

VRM

100

200

300

400

500

Maximum RMS Voltage

VRMS

70

140

210

280

350

VRRM

100

200

300

400

500

Maximum Peak Recurrent Reverse Voltage

o

IO

Average Forward Rectified Current @ Tc = 100 C

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage (per diode) at 15 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Case
Typical Junction Capacitance (Note 1)
Maximum Reverse Recovery Time (IF=15.0A, di/dt=50A/S,TJ=25 C)
o

Junction Operating and Storage Temperature Range

NOTES: (1) Measured at 1 MHz and an applied reverse voltage of 4 volts.

30

IFSM

250

200

VFM

1.0

1.25

@ TC = 25 C
o
@ TC = 100 C

VOLTS

AMPS
VOLTS

IRM

10
500

RJC

C/W

CJ

150

pF

TRR
TJ, TSTG

60

50
-65 to +150

nSec
C
4.97fsedr10

D9

DIOTEC ELECTRONICS CORP.

Data Sheet No. SEDR-3000-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

30 AMP ULTRAFAST RECOVERY DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES UFR3001C - UFR3005C
250

200

150

100

NOTE 1

Resistive and Inductive Loads

50

0
10

100

Case Temperature, C

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10

100

TC = 100 oC

1.0

UFR3001C-3002C

10

0.1

1.0

TC = 25 oC
0.01

UFR3003C-3005C
0.001

0.1

20

Instantaneous Forward Voltage (Volts)

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

300

240

NOTES

180

(1) JEDEC Method, 8.3 mSec. Single Half Sine Wave

120

(2) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

(3) TC = 25 o C, f = 1 MHz, VSIG = 50 mV P-P

60

0
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

D10

4.97bsedr30

SECTION E
STANDARD RECOVERY
FULL WAVE BRIDGE
RECTIFIERS

DUAL IN-LINE PACKAGE

DT

+
S1NB
60 46

FDI104

1 AMPERE
50 to 1000 VOLTS

CYLINDRICAL PACKAGE
1 to 2 AMPERES
50 to 1000 VOLTS

VERTICAL, SIDE LOOKING, PACKAGE

DT
SB200

DT
SB404L

DIOTEC
KBLO8
_

AC

SB506
712
AC

2 to 50 AMPERES
50 to 1000 VOLTS

RECTANGULAR HORIZONTAL PACKAGE

DT
FDB306

3 to 10 AMPERES
50 to 1000 VOLTS

RECTANGULAR HORIZONTAL PACKAGES

15 to 50 AMPERES
50 to 1000 VOLTS

DIOTEC ELECTRONICS CORP. - 18020 Hobart Blvd., Unit B - Gardena, CA 90248 U.S.A. - PH: 310-767-1052 - FX: 310-767-7958

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDI-100-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
THE DI PACKAGE

PRV Ratings from 50 to 1000 Volts

DT

Surge overload rating to 50 Amps peak

SERIES DI100 - DI110

_

DI104

DT

A1

DI104
Reliable low cost molded plastic construction

Ideal for printed circuit board applications

UL RECOGNIZED - FILE #E124962

D
L1

MECHANICAL DATA

L
B
B1

Case: Molded plastic, U/L Flammability Rating 94V-0

Terminals: Rectangular pins

Sym
_

A
A1
B
B1
B2
C
D
L
L1

Soldering: Per MIL-STD 202 Method 208 guaranteed

Polarity: Marked on case

Mounting Position: Any

Weight: 0.05 Ounces (1.3 Grams)

B2
Minimum
mm
in
0.290
7.4
0.245
6.2
0.41
0.016
0.195
5.0
0.300
7.6
9.3
0.355
3.2
0.125
3.9
0.155
0.060* 1.5*

Maximum
mm
in
7.9
0.310
6.5
0.255
0.51
0.020
0.205
5.2
8.9
0.350
9.3
0.365
3.4
0.135
0.165
4.3

* This dimension is "Typical".

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

DI100 DI101 DI102 DI104 DI106 DI108 DI110

Maximum DC Blocking Voltage

VRM

50

100

200

400

600

800

1000

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Average Forward Rectified Current @ TA = 40o C

IO

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method).

IFSM

50

Maximum Forward Voltage (Per Diode) at 1 Amp DC

VFM

@ TA = 25o C
Maximum Average DC Reverse Current
@ TA = 100o C
At Rated DC Blocking Voltage
Junction to Ambient (Note 1)
Typical Thermal Resistance
Junction to Lead (Note 1)
Operating and Storage Temperature Range
NOTES: (1) Bridge mounted on PC Board with 0.5" sq. (13 mm sq.) copper pads

VOLTS

AMPS

1.1

VOLTS
A
mA

RJA
RJL

5.0
0.5
40
15

C/W

TJ, TSTG

-55 to +150

IRM

3.01 01di

E1

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDI-100-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1 AMP MINIATURE BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES DI100 - DI110
50

60Hz
Resistive or Inductive Loads

40

30

NOTE 2
NOTE 1

20

10

10

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

Ambient Temperature, o C
FIGURE 1. FORWARD CURRENT DERATING CURVE

100
10

TA = 125 oC

10

1.0

NOTE 3
1.0

0.1

0.1
TJ = 25 oC

.01

0.01

20

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

100

NOTES
(1) Mounted on PC Board With 0.5" Sq. (13 mm Sq,) Copper Pads
And Bridge Lead Length of 0.06" (1.5 mm)
NOTE 4

(2) TJ = 150 oC
(3) TJ = 25o C; Pulse Width = 300 Sec, 1% Duty Cycle

10

(4) TJ = 25o C; f = 1 MHz; Vsig = 50mVp-p

5
1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

E2

3.01 01di

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDI-101-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
Glass Passivated for high reliability/temperature performance

SERIES S1NB05 - S1NB100

ACTUAL SIZE OF
MDI PACKAGE
+
S1NB
60 46

MILLIMETERS

SYM

PRV Ratings from 50 to 1000 Volts

Surge overload rating to 30 Amps peak

Reliable low cost molded plastic construction

Ideal for printed circuit board applications

MIN

MAX

MIN

MAX

6.25

6.767

0.246

0.266

0.43

0.69

0.017

0.027

BI

0.127

0.381

0.005

0.015

B2
C
D

4.75

5.26

0.187

0.207

6.55
2.27

7.06
2.8

0.258
0.09

0.278
0.11

D1
D2

2.9

0.116

0.146
0.136

S1NB
60 46

MECHANICAL DATA

INCHES

3.7
3.45

0.8*

15 Max

0.032*

15 Max
* Chamfer - Typical

Case: Molded plastic, U/L Flammability Rating 94V-0

Terminals: Rectangular pins

A
Soldering: Per MIL-STD 202 Method 208 guaranteed

D1
Polarity: Marked on case
D2

Mounting Position: Any

B1

B2

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

SYMBOL

RATINGS

Maximum DC Blocking Voltage

VRM

S1NB S1NB S1NB S1NB S1NB S1NB S1NB

05
10
20
40
60
80
100
50
100
200
400
600
800
1000

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Series Number

Average Forward Rectified Current @ TA = 40o C

UNITS

VOLTS

IO

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method).

IFSM

50

Maximum Forward Voltage (Per Diode) at 1 Amp DC

VFM

1.05

VOLTS
A
mA

R JA
RJL

5.0
0.5
40
15

C/W

TJ, TSTG

-55 to +150

o
Maximum Average DC Reverse Current
@ TA = 25 C
At Rated DC Blocking Voltage
@ TA = 125o C
Junction to Ambient (Note 1)
Typical Thermal Resistance
Junction to Lead (Note 1)

Operating and Storage Temperature Range

NOTES: (1) Bridge mounted on PC Board with 0.5" sq. (13mm sq.) copper pads

IRM

AMPS

3.0101s1nb

E3

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDI-101-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1 AMP MINIATURE BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES S1NB05 - S1NB100

60

60Hz Resistive or Inductive Loads

50

40

NOTE 1
30

20

NOTE 2

10

0
10

100

Ambient Temperature, C

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10
100

TA = 125 oC

1.0

NOTE 3

10

1.0

0.1

0.1
TJ = 25 oC

0.01

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

.01
20

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

100

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

NOTE 4

NOTES
(1) Mounted on PC Board With 0.5" Sq. (13 mm Sq.) Solder Pads
(2) TJ = 150o C

10

(3) TJ = 25 C; Pulse Width = 300 Sec, 1% Duty Cycle

o

5
1

10

100

(4) TJ = 25o C; f = 1 MHz; Vsig = 50mVp-p

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

E4

3.1 01s1nb

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRWB-100-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
WB PACKAGE

PRV Ratings from 50 to 1000 Volts

SERIES WB100 - WB110

A
Surge overload rating to 50 Amps peak
D

Reliable low cost molded plastic construction

Ideal for printed circuit board applications

L
One (1)
Lead
(+)

UL RECOGNIZED - FILE #E141956

L1
Three (3)
Leads

MECHANICAL DATA

Case: Molded plastic, U/L Flammability Rating 94V-0

B1
B1

Terminals: Round silver plated pins

+
AC

AC

Soldering: Per MIL-STD 202 Method 208 guaranteed

MILLIMETERS
SYM

Polarity: Marked on case

Mounting Position: Any

Weight: 0.05 Ounces (1.3 Grams)

INCHES

MIN

MAX

MIN

MAX

8.6

8.89

0.340

0.350

0.76

0.81

0.030

0.032

B1

4.6

5.6

0.180

0.220

D
L

5.1
30.5

5.6
n/a

0.200
1.20

0.220
n/a

L1

25.4

n/a

1.0

n/a

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

WB
100
50

UNITS

WB
101
100

WB
102
200

WB
104
400

WB
106
600

WB
108
800

WB
110
1000

Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Average Forward Rectified Current @ TA = 50o C

VOLTS

IO

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 125o C

IFSM

50

Maximum Forward Voltage (Per Diode) at 1 Amp DC

VFM

1.0

VOLTS

IRM

10 (Typical < 0.1A)

R JA
RJL

40
15

C/W

TJ ,TSTG

-40 to +125 (Junction), -40 to +150 (Storage)

Maximum Average DC Reverse Current

o
@ TA = 25 C
At Rated DC Blocking Voltage
Junction to Ambient (Note 1)
Typical Thermal Resistance
Junction to Lead (Note 1)
Operating and Storage Temperature Range

NOTES: (1) Bridge mounted on PC Board with 0.2" sq. (5.5mm sq.) copper pads and lead length of 0.375" (9.5mm).

AMPS

3.0101wb

E5

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRWB-100-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES WB100 - WB110
50

60 Hz Resistive or Inductive Loads

40

30

NOTE 1

20

NOTE 2
10

0
10

100

Ambient Temperature, C

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

20
10

10

TA = 100 oC
1.0

1.0

NOTE 3

0.1

TA = 25 oC

0.1

0.01
20

60

80

100

120

140

0.01

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

NOTES
100

(1) Bridge Mounted on PC Board With 0.2" Sq. (5.5mm Sq.)

Cooper Pads and Bridge Lead Length of 0.375" (9.5mm)
NOTE 4
(2) TJ = 125o C
(3) TJ = 25o C; Pulse Width = 300 Sec, 1% Duty Cycle
o

(4) TJ = 25 C; f = 1 MHz; VSIG = 50mVP-P

10
5
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

E6

3.01 01wb

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRWB-150-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
WB PACKAGE

PRV Ratings from 50 to 1000 Volts

SERIES WB150 - WB1510

Surge overload rating to 50 Amps peak

Reliable low cost molded plastic construction

Ideal for printed circuit board applications

L
One (1)
Lead
(+)

UL RECOGNIZED - FILE #E141956

L1
Three (3)
Leads

MECHANICAL DATA
B
Case: Molded plastic, U/L Flammability Rating 94V-0

B1

Terminals: Round silver plated pins

B1

+
AC

+
AC

Soldering: Per MIL-STD 202 Method 208 guaranteed

MILLIMETERS

Polarity: Marked on case

SYM

Mounting Position: Any

Weight: 0.05 Ounces (1.3 Grams)

INCHES

MIN

MAX

MIN

MAX

8.6

8.89

0.340

0.350

0.76

0.81

0.030

0.032

B1

4.6

5.6

0.180

0.220

D
L

5.1
30.5

5.6
n/a

0.200
1.20

0.220
n/a

L1

25.4

n/a

1.0

n/a

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

WB
150
50

UNITS

WB
151
100

WB
152
200

WB
154
400

WB
156
600

WB
158
800

WB
1510
1000

Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Average Forward Rectified Current @ TA = 25o C

Peak Forward Surge Current. Single 60Hz Half-Sine Wave
Superimposed on Rated Load (JEDEC Method). TJ = 125o C
Maximum Forward Voltage (Per Diode) at 1 Amp DC
Maximum Average DC Reverse Current
@ TA = 25o C
At Rated DC Blocking Voltage
Junction to Ambient (Note 1)
Typical Thermal Resistance
Junction to Lead (Note 1)
Operating and Storage Temperature Range

VOLTS

IO

1.5

IFSM

50

VFM

1.0

VOLTS

IRM

10 (Typical < 0.1A)

RJA
RJL
TJ ,TSTG

35
15

C/W

-40 to +125 (Junction), -40 to +150 (Storage)

NOTES: (1) Bridge mounted on PC Board with 0.2" sq. (5.5 mm sq.) copper pads and lead length of 0.375" (9.5 mm).

AMPS

3.011_5wb

E7

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRWB-150-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1.5 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES WB150 - WB1510

50

60Hz
Resistive or Inductive Loads

40

30

20

NOTE 2
NOTE 1

10

0
10

100

Ambient Temperature, o C

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

20
10
100

10

1.0

TA = 100o C

NOTE 2
1.0

0.1
0.1
TA = 25o C

.01
20

60

80

100

120

140

0.01

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

100

NOTES
(1) Bridge Mounted on PC Board With 0.2" Sq. (5.5mm Sq.)
Copper Pads And Bridge Lead Length of 0.375" (9.5mm)

NOTE 4

(2) TJ = 125o C
(3) TJ = 25o C; Pulse Width = 300 Sec, 1% Duty Cycle

10

(4) TJ = 25o C; f = 1 MHz; Vsig = 50mVp-p

5
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

E8

3.11_5wb

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRWB-200-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
WB PACKAGE

PRV Ratings from 50 to 1000 Volts

SERIES WB200 - WB210

Surge overload rating to 60 Amps peak

Reliable low cost molded plastic construction

Ideal for printed circuit board applications

L
One (1)
Lead
(+)

UL RECOGNIZED - FILE #E141956

L1
Three (3)
Leads

MECHANICAL DATA

B
B1

Case: Molded plastic, U/L Flammability Rating 94V-0

B1

Terminals: Round silver plated pins

+
AC

Soldering: Per MIL-STD 202 Method 208 guaranteed

AC

MILLIMETERS
SYM

MIN

MAX

MIN

MAX

8.6

8.89

0.340

0.350

Polarity: Marked on case

Mounting Position: Any

Weight: 0.05 Ounces (1.3 Grams)

INCHES

0.76

0.81

0.030

0.032

B1

4.6

5.6

0.180

0.220

D
L

5.1
30.5

5.6
n/a

0.200
1.20

0.220
n/a

L1

25.4

n/a

1.0

n/a

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

UNITS

Maximum DC Blocking Voltage

VRM

WB
200
50

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Series Number

Average Forward Rectified Current @ TA = 25o C

Peak Forward Surge Current. Single 60Hz Half-Sine Wave
Superimposed on Rated Load (JEDEC Method). TJ = 150O C
Maximum Forward Voltage (Per Diode) at 2 Amp DC

WB
202
200

WB
204
400

WB
206
600

WB
208
800

WB
210
1000

IO

IFSM

60

VFM
o

@ TA = 25 C
Maximum Average DC Reverse Current
@ TA = 100o C
At Rated DC Blocking Voltage
Junction to Ambient (Note 1)
Typical Thermal Resistance
Junction to Lead (Note 1)
Operating and Storage Temperature Range

WB
201
100

IRM
R JA
RJL
TJ ,TSTG

NOTES: (1) Bridge mounted on PC Board with 0.2" sq. (5.5mm sq.) copper pads and lead length of 0.375" (9.5 mm).

VOLTS

AMPS

1.0

VOLTS

10 (Typical < 0.1A)

1
40
15
-55 to +150

A
mA
C/W
C
3.01 0 2 w b

E9

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRWB-200-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

2 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES WB200 - WB210
60

50

60Hz
Resistive or Inductive Loads

40

NOTE 1

30

20

NOTE 2
10

Ambient Temperature, o C

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

20
10

100
TJ = 125 oC

10

1.0

TJ = 100 oC

NOTE 3
1.0

0.1
0.1
TJ = 25 oC
.01
20

60

80

100

120

140

0.01

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

NOTES

100

(1) Bridge Mounted on PC Board With 0.22" Sq. (5.5mm Sq.)

Copper Pads And Bridge Lead Length of 0.375" (9.5mm)

NOTE 4

(2) TJ = 150o C
(3) TJ = 25o C; Pulse Width = 300 Sec, 1% Duty Cycle
10

(4) TJ = 25o C; f = 1 MHz; Vsig = 50mVp-p

5
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

E10

3.01 02wb

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRSB-200-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
SB2 PACKAGE

PRV Ratings from 50 to 1000 Volts

Surge overload rating to 60 Amps peak

SERIES SB200 - SB210

C

DIOTEC 009
SB208

D1

Reliable low cost molded plastic construction

DIOTEC 009
SB208

Ideal for printed circuit board applications

L

UL RECOGNIZED - FILE #E124962

B1

MECHANICAL DATA

A1

Case: Molded plastic, U/L Flammability Rating 94V-0

Terminals: Round silver plated pins

MILLIMETERS

Soldering: Per MIL-STD 202 Method 208 guaranteed

SYM

MAX

MIN

MAX

5.99

7.01

0.236

0.276

A1

2.99

3.51

0.118

0.138

0.71

0.89

0.028

0.035

Mounting Position: Any

B1
C
D

3.55
16.0
14.0

4.00
18.0
15.0

0.140
0.63
0.55

0.160
0.71
0.59

Weight: 0.1 Ounces (2.8 Grams)

D1
L

13.2
12.7

13.7
n/a

0.52
0.50

0.54
n/a

Polarity: Marked on case

MIN

INCHES

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

SB
200
50

UNITS

SB
201
100

SB
202
200

SB
204
400

SB
206
600

SB
208
800

SB
210
1000

Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Average Forward Rectified Current @ TA = 55O C

VOLTS

IO

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 150O C

IFSM

60

Maximum Forward Voltage (Per Diode) at 1 Amp DC

VFM

1.05

VOLTS
A

RJA
RJL

10
500
30
11

C/W

TJ ,TSTG

-55 to +150

@ TA = 25o C
Maximum Average DC Reverse Current
@ TA = 125o C
At Rated DC Blocking Voltage
Junction to Ambient (Note 1)
Typical Thermal Resistance.
Junction to Lead (Note 1)
Operating and Storage Temperature Range
NOTES: (1) Bridge mounted on PC Board with 0.47" sq.(12mm sq.) copper pads.

IRM

AMPS

3.01 02sb

E11

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRSB-200-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

2 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SB200 - SB210 SERIES
60

60Hz Resistive and Inductive Loads

50

40

NOTE 1

NOTE 2

30

20

10
1

10

Ambient Temperature, o C

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100

20

TJ = 125o C

10

TJ = 100o C

10

NOTE 3
1.0
1.0

0.1
0.1

TA = 25o C

0.01

.01

Instantaneous Forward Voltage (Volts)

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

NOTES

100

(1) Bridge Mounted on PC Board With 0.47" Sq. (12mm Sq.)

Copper Pads

NOTE 4

(2) TJ = 150o C
(3) TJ = 25 C; Pulse Width = 300 Sec, 1% Duty Cycle
o

10

(4) TJ = 25o C; f = 1 MHz; VSIG = 50mVP-P

5
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

E12

3.01 02sb

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-300-1C

ABDB-300-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
PRV Ratings from 50 to 1000 Volts

ACTUAL SIZE

SERIES DB300-DB310 and ADB304-ADB308

DT
DB306

High surge overload rating of 60 Amps peak

Reliable low cost molded plastic construction

BH

Ideal for printed circuit board applications

LL

UL RECOGNIZED - FILE #E124962

_

MECHANICAL DATA

LD

Case: Molded plastic, U/L Flammability Rating 94V-0

D1

Terminals: Round silver plated copper pins

MILLIMETERS

Soldering: Per MIL-STD 202 Method 208 guaranteed (NOTE 1)

Polarity: Marked on top of case; positive lead at beveled corner
Mounting Position: Any. Thru hole provided for #6 screw (NOTE 2)
Weight: 0.13 Ounces (3.6 Grams)

SYM

INCHES

MIN

MAX

MIN

MAX

D1

BL

14.7

15.7

0.58

0.62

BH

4.8

5.3

0.19

0.21

D1

10.3

11.3

0.405

0.445

LL
LD

19.0
0.7

n/a
0.9

0.75
0.028

n/a
0.035

BL
_

BL

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified. Single phase, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.

RATINGS

PARAMETER (TEST CONDITIONS)

SYMBOL

Series Number
Maximum DC Blocking Voltage

VRM

Working Peak Reverse Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

VRRM

RMS Reverse Voltage

VR (RMS)

Power Dissipation in V(BR) Region for 100 S Square Wave

CONTROLLED
AVALANCHE
ADB ADB ADB DB
304 306 308 300

DB DB
301 302

DB
304

DB
306

DB DB
308 310

400

100

400

600

800 1000

600 800

50

200

VOLTS
280

420 560

35

70

140

280

PRM

300

n/a

Continuous Power Dissipation in V(BR) Region

@ THS=80 oC (Heat Sink Temp)

PR

n/a

Thermal Energy (Rating for Fusing) t < 8.3mSec

I 2t

15

IFSM

60

IO

3
2

Junction Operating and Storage Temperature Range

TJ, TSTG

-55 to +150

Minimum Avalanche Voltage

V(BR) Min

450

Maximum Avalanche Voltage

V(BR) Max

900 1100 1300

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). Tc = 60O C
@ TC = 60o C (Note 2)
Average Forward Rectified Current
@ TA = 25o C (Note 3)

Maximum Forward Voltage (Per Diode) at 1.5 Amps DC

VFM

Typical Junction Capacitance (Note 4)

Maximum Reverse Current at Rated VRM

@ TA = 25o C
@TA = 125o C

Minimum Insulation Breakdown Voltage (Circuit to Case)

Typical Thermal Resistance

Junction to Ambient (Note 2)

Junction to Case (Note 2)

UNITS

NON-CONTROLLED
AVALANCHE

420

560

700

WATTS

650

850

AMPS2
SEC
AMPS

C
n/a
n/a

VOLTS

0.95 (Typical < 0.9)

CJ

21

pF

IRM

5 (Typical < 0.1A)

500

VISO

2500

VOLTS

RJA
RJC

NOTES: (1) Bolt bridge on heat sink with #6 screw, using silicon thermal compound between bridge and mounting surface for maximum heat transfer.
(2) Bridge mounted on 4.0" sq. x 0.11" thick (10.5cm sq. x 0.3cm) aluminum plate
(3) Bridge mounted on PC Board with 0.5" sq. (12mm sq.) copper pads and bridge lead length of 0.375" (9.5mm)
(4) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts

C/W
3.01 03db

E13

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-300-2C

ABDB-300-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

3 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES DB300 - DB310 and SERIES ADB304 - ADB308
60

60Hz
Resistive and Inductive Loads

50

Case, Tc

40

NOTE 1
30

NOTE 2

Ambient, TA

20

10
1

10

100

Temperature, oC

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

50
o

10

TJ = 125 C
10

NOTE 3

1.0

1.0

0.1

0.1

.01

TJ = 25 oC

20

60

80

100

120

140

0.01

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

100

NOTES
NOTE 4

(1) Case Temperature, TC, With Bridge Mounted on 4" Sq. x 0.11" Thick
(10.5cm Sq. x 0.3cm) Aluminum Plate
Ambient Temperature, TA, With Bridge Mounted on PC Board With
0.5" Sq. (12mm Sq.) Pads and Lead Length of 0.375" (9.5mm)

10

(2) TC = 60o C
5
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

E14

(3) TJ = 25o C; Pulse Width = 300Sec; 1% Duty Cycle

(4) TJ = 25o C; f = 1 MHz; Vsig = 50mVp-p

4.97bbrwb200

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRSB-400-1C

ABSB-400-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
SB4 PACKAGE

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

SERIES:

SB400L - SB410L
ASB404L - ASB408L

DT
SB404L
C

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

DT
SB404L

SURGE OVERLOAD RATING TO 200 AMPS PEAK

D

D1

UL RECOGNIZED - FILE #E124962

MECHANICAL DATA
_

L1

Case: Molded plastic, U/L Flammability Rating 94V-0

L
B

Terminals: Round silver plated copper pins

MILLIMETERS

SYM

Soldering: Per MIL-STD 202 Method 208 guaranteed (NOTE 1)

Polarity: Marked on case
Mounting Position: Any.

INCHES

MIN

MAX

MIN

MAX

A
A1

6.4
2.06

6.65
2.18

0.252
0.061

0.262
0.065

B
B1
C
D

1.22
4.57

1.32
5.59

0.048
0.180

0.052
0.220

19.1
15.62

19.3
15.88

0.750
0.615

0.760
0.625

D1

14.38*

n/a

0.566*

n/a

27.94
n/a
1.2
25.4
n/a
1.0
L1
* This measurement is "Typical"

n/a
n/a

Weight: 0.2 Ounces (5.6 Grams)

B1
A1
A

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

CONTROLLED
AVALANCHE

UNITS

NON-CONTROLLED
AVALANCHE

ASB ASB ASB SB SB SB SB SB SB SB

404L 406L 408L 400L 401L 402L 404L 406L 408L 410L

Series Number
Maximum DC Blocking Voltage

VRM

Working Peak Reverse Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

VRRM

RMS Reverse Voltage

VR (RMS)

400

600 800

50

100

200

400

600

800 1000

VOLTS
280

420 560

35

70

140

280

420

560

700
2

Thermal Energy (Rating for Fusing)

Peak Forward Surge Current. Single 60Hz Half-Sine Wave
Superimposed on Rated Load (JEDEC Method) TJ = 150O C
Average Forward Rectified Current @ TA = 50O C

It

93

IFSM

200

IO

4
-55 to +150

AMPS
SEC

AMPS

Junction Operating and Storage Temperature Range

TJ, TSTG

Minimum Avalanche Voltage

V(BR) MIN

450

850

n/a

Maximum Avalanche Voltage

V(BR) MAX

900 1100 1300

n/a

Maximum Forward Voltage (Per Diode) at 4 Amps DC

@ TA = 25o C
Maximum Reverse Current at Rated VRM
@TA = 125o C
Minimum Insulation Breakdown Voltage (Circuit to Case)
Junction to Ambient (Note 1)
Junction to Lead (Note 2)

Typical Thermal Resistance

650

VOLTS

VFM

0.95 (Typical < 0.90)

IRM

5
1

A
mA

VISO

2500

VOLTS

RJA
RJL

19.0
2.4

C/W
3.01 04sbl

NOTES: (1) Bridge mounted on 3.0" sq. x 0.11" thick (7.5cm sq. x 0.3cm) aluminum plate.
(2) Bridge mounted on PC Board with 0.5" sq. (12mm sq.) copper pads and a lead length of 0.375" (9.5mm).

E15

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRSB-400-2C

ABSB-400-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

4 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SB400L - SB410L and SERIES ASB404L - ASB408L
200

NOTE 1
175

150

125

100

60Hz
Resistive or Inductive Loads

75

NOTE 2
50
1

Ambient Temperature, o C

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
10

TJ = 100o C

10

1.0

NOTE 3
0.1

1.0
TJ = 25o C

0.01

0.1

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

NOTES

250

(1) Bridge Mounted on 3.0" Sq. x 0.11" Thick (7.5cm Sq. x 015cm)
Aluminum Plate

200

NOTE 4
150

(2) TJ = 150o C

100

(3) TJ = 25o C; Pulse Width = 300Sec; 1%Duty Cycle

50

(4) TJ = 25o C; f = 1 MHz; Vsig = 50mVp-p

0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

E16

3.1 04sbl

DIOTEC ELECTRONICS CORP.

Data Sheet No. BKBL-400-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
KBL PACKAGE

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

SERIES KBL00 - KBL10

C

DIOTEC
KBLO8

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

DIOTEC
D

KBLO8

SURGE OVERLOAD RATING TO 200 AMPS PEAK

IDEAL FOR PRINTED CIRCUIT BOARD APPLICATIONS

UL RECOGNIZED - FILE #E141956

MECHANICAL DATA

L1

Case: Molded plastic, U/L Flammability Rating 94V-0

Terminals: Round silver plated pins

_

MILLIMETERS

Soldering: Per MIL-STD 202 Method 208 guaranteed

Polarity: Marked on case

Mounting Position: Any

Weight: 0.2 Ounces (5.6 Grams)

SYM

MIN

INCHES

MAX

MIN

MAX

6.22

6.48

0.245

0.255

A1

2.05

2.18

0.081

0.085

B1

A1

1.22

1.32

0.048

0.052

B1
C
D
L

4.57
18.90
12.1
27.94

5.59
19.10
12.7
n/a

0.180
0.620
0.470
1.10

0.220
0.630
0.500
n/a

L1

25.4

n/a

1.00

n/a

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

UNITS

Maximum DC Blocking Voltage

VRM

KBL
00
50

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

VRRM

50

100

200

400

600

800

1000

Series Number

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ TA = 65 C

KBL
01
100

KBL
02
200

KBL
04
400

KBL
06
600

KBL
08
800

KBL
10
1000
VOLTS

IO

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 150o C

IFSM

200

Maximum Forward Voltage (Per Diode) at 4 Amps DC

VFM

0.95 (Typical < 0.90)

VOLTS

IRM

5
1

A
mA

RJA
RJL

19.0
2.4

C/W

TJ ,TSTG

-55 to +150

@ TA = 25o C
Maximum Average DC Reverse Current
@ TA = 100o C
At Rated DC Blocking Voltage
Junction to Ambient (Note 1)
Typical Thermal Resistance
Junction to Lead (Note 2)
Operating and Storage Temperature Range

NOTES: (1) Bridge mounted on 3.0" sq. x 0.11" thick (7.5cm sq. x 0.3cm) aluminum plate.
(2) Bridge mounted on PC Board with 0.5" sq. (12mm sq.) copper pads and a lead length of 0.375" (9.5mm).

AMPS

3.0104kbl

E17

DIOTEC ELECTRONICS CORP.

Data Sheet No. BKBL-400-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

4 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES KBL00 - KBL10

200

NOTE 1

175

150

125

100

60Hz
Resistive or Inductive Loads

75

NOTE 2
50

Ambient Temperature, o C

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
10

TJ = 100o C

10

1.0

NOTE 3
0.1

1.0

TJ = 25o C

0.01

0.1

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

NOTES

250

(1) Bridge Mounted on 3.0" Sq. x 0.11" Thick (7.5cm Sq. x 0.15cm)
Aluminum Plate

NOTE 3

200
150

(2) TJ = 150O C

100

(3) TJ = 25o C; Pulse Width = 300Sec; 1%Duty Cycle

(4) TJ = 25o C; f = 1 MHz; Vsig = 50mVp-p

50

0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

E18

3.01 04kbl

DIOTEC ELECTRONICS CORP.

Data Sheet No. BSBU-400-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

C1
C2

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

D3

D2
_

SURGE OVERLOAD RATING TO 200 AMPS PEAK

D
D1

A1

IDEAL FOR PRINTED CIRCUIT BOARD APPLICATIONS

L

UL RECOGNIZED - FILE #E124962

L1

MECHANICAL DATA

B1
B

Case: Molded plastic, U/L Flammability Rating 94V-0

SYM

Terminals: Round silver plated pins

Soldering: Per MIL-STD 202 Method 208 guaranteed

Polarity: Marked on case

Mounting Position: Any. Max. mounting torque = 5 in lb

Weight: 0.3 Ounces (8 Grams)

MILLIMETERS

INCHES

MIN

MAX

MIN

MAX

A
A1

6.6

0.260

0.280

4.7

7.1
5.2

0.185

0.205

1.22

1.32

0.048

0.052

B1

4.57

5.59

0.180

0.220

22.70

23.24

0.895

0.915

0.165

C1

4.2

C2

3.6

4.7
4.1

0.140

0.185
0.160

D
D1
D2

n/a
10.3
1.7

19.3
11.3
2.2

n/a
0.405
0.065

0.760
0.455
0.085

D3
L

16.5
25.4

17.8
n/a

0.660
1.0

0.700
n/a

6.8

0.180

0.260

L1

4.57

SERIES SBU4A - SBU4M

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified. Single phase, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

SYMBOL

Series Number

RATINGS

UNITS

SBU
4A

SBU
4B

SBU
4D

SBU
4G

SBU
4J

SBU
4K

SBU
4M

50

100

200

400

600

800

1000

Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

TC = 100o C (Note 1)
TA = 30o C (Note 2)
Peak Forward Surge Current. Single 60Hz Half-Sine Wave
Superimposed on Rated Load (JEDEC Method). TJ = 150O C
Average Forward Rectified Current

Maximum Forward Voltage (Per Diode) at 4 Amps DC

@ TA = 25o C
Maximum Average DC Reverse Current
@ TA = 100o C
At Rated DC Blocking Voltage
Junction to Ambient (Note 2)
Typical Thermal Resistance
Junction to Lead (Note 1)
Operating and Storage Temperature Range

IO

4
4

IFSM

200

VFM

0.95 (Typical < 0.90)

IRM
RJA
RJL
TJ ,TSTG

5 (Typical < 0.1A)

100
19.0
2.4
-55 to +150

VOLTS

AMPS
VOLTS
A
C/W
C
3.01 04sbu

NOTES: (1) Bridge mounted on 2.0" x 1.6" x 0.3" thick (5cm x 4cm x 0.8cm) aluminum plate
(2) Bridge mounted on PC Board with 0.5" sq. (12mm sq.) copper pads and bridge lead length of 0.375" (9.5mm)
(3) Bolt bridge on heat sink with #6 screw, using silicon thermal compound between bridge and mounting surface for maximum heat transfer.

E19

DIOTEC ELECTRONICS CORP.

Data Sheet No. BSBU-400-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

4 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SBU4A - SBU4M
250

NOTE 1
200

Case, TC
150

Ambient, TA
100

NOTE 2

60 Hz

50

Resistive or Inductive Loads

0

Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

50

100

10

TJ = 100 oC

10

1.0

NOTE 3

1.0
0.1

TJ = 25 oC
0.1

0.01
0

Instantaneous Forward Voltage (Volts)

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

NOTES
125

(1) Case Temperature, TC, With Bridge Mounted on

2.0" x 1.6" x 0.3" Thick (5cm x 4cm x 0.8cm) Aluminum Plate

100
Note 4

Ambient Temperature, TA, With Bridge Mounted on

PC Board With 0.5" Sq. (12mm Sq.) Pads and
Bridge Lead Length of 0.375" (9.5mm)

75
50

(2) TJ = 150o C

25

(3) TJ = 25o C; Pulse Width = 300Sec; 1% Duty Cycle

0.1

10

100

(4) TJ = 25o C; f = 1 MHz; Vsig = 50mVp-p

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

E20

3.01 04sbu

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRSB-500-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

SB5 PACKAGE SHOWN ACTUAL SIZE

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

C
A

C1

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

SB506
712
_
AC

D1

SURGE OVERLOAD RATING TO 200 AMPS PEAK

IDEAL FOR PRINTED CIRCUIT BOARD APPLICATIONS

RELIABLE LOW-COST MOLDED PLASTIC CONSTRUCTION

MECHANICAL DATA
B2

B1

B1

B
A1

Case: Molded plastic, U/L Flammability Rating 94V-0

INCHES
SYM

Terminals: Round silver plated pins

Soldering: Per MIL-STD 202 Method 208 guaranteed

Polarity: Marked on case

Mounting Position: Any

Weight: 0.38 Ounces (10.6 Grams)

TYP

MAX

TYP

6.4

0.250

A1

2.06

0.070

1.27

0.05

B1

7.6

0.300

B2
C

10.2
39.9

0.400
1.570

C1

4.8

0.188

21.7

0.855

D1
L

25.4*

21.0

MAX

0.820
1.0*

SERIES SB500 - SB510

* This measurement is a "Minimum"

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

SB
500
50

UNITS

SB
501
100

SB
502
200

SB
504
400

SB
506
600

SB
508
800

SB
510
1000

Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Average Forward Rectified Current @ TA = 55 C

VOLTS

IO

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 150O C

IFSM

200

Maximum Forward Voltage (Per Diode) at 5 Amps DC

VFM

1.0 (Typical < 0.95)

VOLTS

IRM

5
0.5

A
mA

RJA
RJL

17
3.3

C/W

TJ, TSTG

-55 to +150

@ TA = 25o C
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
@ TA = 100o C
Junction to Ambient (Note 1)
Typical Thermal Resistance
Junction to Lead (Note 1)
Junction Operating Temperature Range
NOTES: (1) Unit mounted on 3.0" sq. x 0.11" (7.5cm sq. x 0.3cm) aluminum plate

AMPS

3.01 05sb

E21

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRSB-500-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

5 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SB500 - SB510

250

60Hz Resistive or Inductive Loads

200

NOTE 1
150

100

NOTE 2
50

10

100

Number of Cycles at 60 Hz

Ambient Temperature, C

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

FIGURE 1. FORWARD CURRENT DERATING CURVE

10

100

10
1.0

1.0

NOTE 2

0.1

0.1

TJ = 25o C

0.01

.01 0

Instantaneous Forward Voltage (Volts)

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

NOTES

(1) Bridge Mounted on 3.0" sq. x 0.11" (7.5cm sq. x 0.3cm) Aluminum Plate
(2) TJ = 150o C
o
(3) TJ = 25 C; Pulse Width = 300 Sec; 1% Duty Cycle

E22

3.01 05sb

DIOTEC ELECTRONICS CORP.

Data Sheet No. BSBU-600-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

SBU PACKAGE SHOWN ACTUAL SIZE

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

C1
C2

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

D3

SURGE OVERLOAD RATING TO 250 AMPS PEAK

D2
_

D
D1

IDEAL FOR PRINTED CIRCUIT BOARD APPLICATIONS

A1

THRU-HOLE FOR EASY HEAT SINK MOUNTING

UL RECOGNIZED - FILE #E124962

MECHANICAL DATA

L1

B1
B

Case: Molded plastic, U/L Flammability Rating 94V-0

Terminals: Round silver plated pins

SYM

MILLIMETERS

INCHES

MIN

MAX

MIN

MAX

A
A1

6.6

0.260

0.280

4.7

7.1
5.2

0.185

0.205

1.22

1.32

0.048

0.052
0.220

5.59

0.180

22.7

23.24

0.895

0.915

C1

4.2

4.7

0.165

Polarity: Marked on case

C2

3.6

4.1

0.140

0.185
0.160

Mounting Position: Any. Max. mounting torque = 5 in lb

D
D1
D2

n/a
10.3
1.7

19.3
11.3
2.2

n/a
0.405
0.065

0.760
0.455
0.085

D3
L

16.5
25.4

17.8
n/a

0.660
1.0

0.700
n/a

6.8

0.180

0.260

Soldering: Per MIL-STD 202 Method 208 guaranteed

Weight: 0.3 Ounces (8 Grams)

B1

L1

4.57

4.57

SERIES SBU6A - SBU6M

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified. Single phase, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

SBU
6A

SBU
6B

SBU
6D

SBU
6G

SBU
6J

SBU
6K

SBU
6M

50

100

200

400

600

800

1000

Maximum DC Blocking Voltage

VRM

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

TC = 100o C (Notes 1, 3)
o
TA = 40 C (Note 2)
Peak Forward Surge Current. Single 60Hz Half-Sine Wave
O
Superimposed on Rated Load (JEDEC Method). TJ = 150 C

Average Forward Rectified Current

Maximum Forward Voltage (Per Diode) at 6 Amps DC

@ TA = 25o C
Maximum Average DC Reverse Current
@ TA = 100o C
At Rated DC Blocking Voltage
Junction to Ambient (Note 2)
Typical Thermal Resistance
Junction to Case (Note 3)
Operating and Storage Temperature Range

VOLTS

IO

6
6

IFSM

250

VFM

0.95 (Typical < 0.90)

VOLTS

5 (Typical < 0.5A)

1
16.0
3.1
-55 to +150

A
mA

IRM
RJA
RJC
TJ ,TSTG

NOTES: (1) Bridge mounted on 2.6" x 1.4" x 0.06" thick (6.5cm x 3.5cm x 0.15cm) aluminum plate
(2) Bridge mounted on PC Board with 0.5" sq. (12mm sq.) copper pads and bridge lead length of 0.375" (9.5mm)
(3) Bolt bridge on heat sink with #6 screw, using silicon thermal compound between bridge and mounting surface for maximum heat transfer.

AMPS

C/W
C
3.01 06sbu

E23

DIOTEC ELECTRONICS CORP.

Data Sheet No. BSBU-600-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

6 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SBU6A - SBU6M
250

NOTE 1
200

60Hz
Resistive or Inductive Loads

150

Case, TC
100

Ambient, TA

50

NOTE 2
0

Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100

50

10

TJ = 100 oC

10

1.0

NOTE 3

1.0
0.1

TJ = 25 oC
0.1
0.01
0

Instantaneous Forward Voltage (Volts)

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

400

NOTES

Note 4

(1) Case Temperature, TC, With Bridge Mounted on

2.6" x 1.4" x 0.06" Thick (6.5cm x 3.5cm x 0.15cm)
Aluminum Plate

100

Ambient Temperature, TA, With Bridge Mounted on

PC Board With 0.5" Sq. (12mm Sq.) Pads and
Bridge Lead Length of 0.375" (9.5mm)
(2) TJ = 150o C
10
1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

E24

(3) TJ = 25o C; Pulse Width = 300Sec; 1% Duty Cycle

(4) TJ = 25o C; f = 1 MHz; Vsig = 50mVp-p

3.0106sbu

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-600-1C

ABDB-600-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

ACTUAL SIZE

SERIES DB600 - DB610 and ADB604 - ADB608

DT
DB602

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

BH

SURGE OVERLOAD RATING TO 250 AMPS PEAK

AC

LL

UL RECOGNIZED - FILE #E124962

AC

MECHANICAL DATA

LD

Case: Molded plastic, U/L Flammability Rating 94V-0

D1

Terminals: Round silver plated copper pins

MILLIMETERS
SYM

Soldering: Per MIL-STD 202 Method 208 guaranteed

Polarity: Marked on side of case; positive lead at beleveled corner
Mounting Position: Any. Through hole provided for #6 screw
Weight: 0.13 Ounces (3.6 Grams)

INCHES

MIN

MAX

MIN

MAX

D1

BL

14.7

15.7

0.58

0.62

BH

5.8

6.9

0.23

0.27

D1

10.3

11.3

0.405

0.445

LL
LD

19.0
1.0

n/a
1.1

0.75
0.039

n/a
0.042

BL
_

BL

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified. Single phase, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.

RATINGS

PARAMETER (TEST CONDITIONS)

SYMBOL

Series Number
Maximum DC Blocking Voltage

VRM

Working Peak Reverse Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

VRRM

RMS Reverse Voltage

VR (RMS)

Power Dissipation in V(BR) Region for 100 S Square Wave

CONTROLLED
AVALANCHE
ADB ADB ADB DB
604 606 608 600

DB DB
601 602

DB
604

DB
606

DB DB
608 610

400

600 800

50

100

200

400

600

800 1000

280

420 560

35

70

140

280

420

560

PRM

400

n/a

Continuous Power Dissipation in V(BR) Region

@ THS=80 oC (Heat Sink Temp)

PR

n/a

Thermal Energy (Rating for Fusing) t < 8.3 mSec

I 2t

127

IFSM

250

IO

6
3

Junction Operating and Storage Temperature Range

TJ, TSTG

-55 to +150

Minimum Avalanche Voltage

V(BR) Min

450

Maximum Avalanche Voltage

V(BR) Max

900 1100 1300

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 150O C
@ TC = 50 C (Notes 1, 2)
@ TA = 40o C (Note 3)

Maximum Forward Voltage (Per Diode) at 3 Amps DC

@ TA = 25o C
Maximum Reverse Current at Rated V RM
@TA = 100o C
Minimum Insulation Breakdown Voltage (Circuit to Case)
Junction to Ambient (Note 3)
Junction to Case (Note 2)

Typical Thermal Resistance

NOTES: (1)
(2)
(3)
(4)

650

VFM
CJ

Typical Junction Capacitance (Note 4)

VOLTS

700

WATTS

Average Forward Rectified Current

UNITS

NON-CONTROLLED
AVALANCHE

850

AMPS2
SEC
AMPS

C
n/a

VOLTS

n/a
0.95 (Typical < 0.90)

186

90

186

90

IRM

5 (Typical < 0.5 A)

0.5

A
mA

VISO

2000

VOLTS

RJA
RJC

16.0
5.7

Bolt bridge on heat sink with #6 screw, using silicon thermal compound between bridge and mounting surface for maximum heat transfer.
Bridge mounted on 4.0" sq. x 0.11" thick (10.5cm sq. x 0.3cm) aluminum plate
Bridge mounted on PC Board with 0.5" sq. (12mm sq.) copper pads and bridge lead length of 0.375" (9.5mm)
Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts

C/W
3.01 06db

E25

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-600-2C

ABDB-600-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

6 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES DB600 - DB610 and SERIES ADB604 - ADB608
275
250

60Hz
Resistive or Inductive Loads

225
200

Case, Tc

175

NOTE 1

150
125
100

NOTE 2

Ambient, TA
75
50
25

10

100

Number of Cycles at 60 Hz

Temperature, oC
FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100

100

TJ = 125o C
100
10

TJ = 100o C
10

1.0

NOTE 3

1.0

0.1

TJ = 25o C

0.1

0.01

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS PER DIODE

1000

NOTES
(1) Case Temperature, TC, With Bridge Mounted on 4"Sq. x 0.11" Thick
(10.5cm Sq. x 0.3cm) Aluminum Plate

NOTE 4

Ambient Temperature, TA, With Bridge Mounted on PC Board With

0.5" Sq. (12mm Sq.) Pads and Lead Length of, 0.375" (9.5mm)

100

(2) TJ = 150o C
(3) TJ = 25o C; Pulse Width = 300Sec; 1% Duty Cycle

50 - 400V
600 - 1000V

(4) TJ = 25 C; f = 1 MHz; Vsig = 50mVp-p

10
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE
3.01 06db

E26

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRHB-600-1C

ABHB-600-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

0.90 (22.86)

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

0.04 (1.02)

DIMENSIONS SHOWN IN
INCHES (MILLIMETERS)

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE
Unique structure - DC leads on one side, AC leads on

0.50
(12.7)

0.04 (1.02)

0.250 +/- 0.010

(6.35 +/- 0.254)

the opposite side

DC LEADS

Ideal for DC motor related applications

0.50
(12.7)

0.69
(17.53)

UL RECOGNIZED - FILE #E141956

0.50
(12.7)

MECHANICAL DATA
0.25
(6.35)

0.43 Max
(10.9)

Case: Molded plastic, U/L Flammability Rating 94V-0

AC LEADS

Terminals: Round silver plated copper pins/faston connectors

AC
FASTON
TERMINALS

0.11
(2.79)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Polarity: Marked on case
Mounting Position: Any.
Weight: 0.13 Ounces (3.6 Grams)

EPOXY FILLED
CAVITY

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratingsat25Cambienttemperature unlessotherwisespecified.
Single phase, half wave,60Hz, resistive or inductive load.
Forcapacitive loads, derate currentby20%.

RATINGS

PARAMETER (TEST CONDITIONS)

SYMBOL

CONTROLLED
AVALANCHE

AHBU AHBU AHBU HBU HBU HBU HBU

604
606 608 600 601 602 604

Series Number
Maximum DC Blocking Voltage

VRM

Working Peak Reverse Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

HBU
606

HBU HBU
608 610

400

600 800

50

100

200

400

600

800 1000 VOLTS

280

420 560

35

70

140

280

420

560

VRRM

RMS Reverse Voltage

VR (RMS)

Power Dissipation in V(BR) Region for 100 S Square Wave

PRM

400

n/a

Continuous Power Dissipation in V(BR) Region

@ THS=80 oC (Heat Sink Temp)

PR

n/a

Thermal Energy (Rating for Fusing)

I 2t

127

IFSM

250

IO

6
3
-55 to +150

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 150O C
@ TC = 50 C
@ TA = 40o C

Average Forward Rectified Current

AMPS2
SEC
AMPS

Junction Operating and Storage Temperature Range

TJ, TSTG

Minimum Avalanche Voltage

V(BR) Min

450

850

n/a

Maximum Avalanche Voltage

V(BR) Max

900 1100 1300

n/a

Maximum Forward Voltage (Per Diode) at 6 Amps DC

@ TA = 25o C
Maximum Reverse Current at Rated V RM
@TA = 100o C
Minimum Insulation Breakdown Voltage (Circuit to Case)
Junction to Ambient
Junction to Case

700

WATTS

Typical Thermal Resistance (on Heat Sink)

UNITS

NON-CONTROLLED
AVALANCHE

650

VOLTS

VFM

0.95 (Typical < 0.90)

IRM

5
1

A
mA

VISO

2000

VOLTS

RJA
RJC

16.0
5.7

C/W
3.01 06hbu

E27

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRHB-600-2C

ABHB-600-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

6 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES HBU600 - HBU610 and SERIES AHBU604 - AHBU608

60Hz Resistive or Inductive Loads

275
250
225
200

Case
NOTE 1

175
150
125

Ambient

100

NOTE 2

75
50
25

10

Temperature, C
FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
500

TJ = 125o C
100
10

TJ = 100o C

10

1.0

NOTE 3
1.0

TJ = 25 oC

0.1
0.1

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS PER DIODE
0.01

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE
NOTES
(1) Ambient = Ambient temperature, TA. P.C. Board mounting with 0.375" (9.5 mm) Lead lengths
Case = Case Temperature, TC. Mounted on aluminum plate 5.5" x 6.0" x 0.11" thick (14cm x 15cm x 0.3 cm)
(2) TJ = 150o C
(3) TJ = 25o C; Pulse Width = 300 Sec; 1% Duty Cycle

E28

3.01 06hbu

DIOTEC ELECTRONICS CORP.

Data Sheet No. BSBU-800-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

C1
C2

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

D3

D2
_

D
D1

SURGE OVERLOAD RATING TO 300 AMPS PEAK

A1

THRU-HOLE FOR EASY HEAT SINK MOUNTING

L

UL RECOGNIZED - FILE #E124962

MECHANICAL DATA

L1

B1
B

Case: Molded plastic, U/L Flammability Rating 94V-0

SYM

Terminals: Round silver plated pins

MILLIMETERS

INCHES

MIN

MAX

MIN

MAX

6.6

0.260

0.280

A1

4.7

7.1
5.2

0.185

0.205

1.22

1.32

0.048

0.052
0.220

B1

5.59

0.180

22.7

23.24

0.895

0.915

4.2
3.6

4.7
4.1

0.165

Polarity: Marked on case

C1
C2

0.140

0.185
0.160

Mounting Position: Any. Max. mounting torque = 5 in lb

D
D1
D2

n/a
10.3
1.7

19.3
11.3
2.2

n/a
0.405
0.065

0.760
0.455
0.085

D3
L

16.5
25.4

17.8
n/a

0.660
1.0

0.700
n/a

6.8

0.180

0.260

Soldering: Per MIL-STD 202 Method 208 guaranteed

Weight: 0.3 Ounces (8 Grams)

L1

4.57

4.57

SERIES SBU8A - SBU8M

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified. Single phase, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

SBU
8A

SBU
8B

SBU
8D

SBU
8G

SBU
8J

SBU
8K

SBU
8M

Maximum DC Blocking Voltage

VRM

50

100

200

400

600

800

1000

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

VRRM

50

100

200

400

600

800

1000

Maximum Peak Recurrent Reverse Voltage

Average Forward Rectified Current

IO

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 150O C

IFSM

300

Maximum Forward Voltage (Per Diode) at 8 Amps DC

VFM

TC = 100 C (Notes 1, 3)

@ TA = 25o C
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
@ TA = 125o C
Junction to Ambient (Note 2)
Typical Thermal Resistance
Junction to Case (Note 1)
Operating and Storage Temperature Range

VOLTS

AMPS

IRM
RJA
RJC
TJ ,TSTG

0.95 (Typ. 0.90)

VOLTS
A
mA

5 (Typical < 0.5mA)

0.5
16
3

C/W

-55 to +150

NOTES: (1) Bridge mounted on 3.2" sq. x 0.12" thick (8.2cm sq. x 0.3cm) aluminum plate
(2) Bridge mounted on PC Board with 0.5" sq. (12mm sq.) copper pads and bridge lead length of 0.375" (9.5mm)
(3) Bolt bridge on heat sink with #6 screw, using silicon thermal compound between bridge and mounting surface for maximum heat transfer.

3.01 08sbu

E29

DIOTEC ELECTRONICS CORP.

Data Sheet No. BSBU-800-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

8 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SBU8A - SBU8M
300

NOTE 1
250

200

60Hz
150

NOTE 2
100

50

Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100
50

10

10

NOTE 3

TJ = 100o C
1.0

1.0

0.1

TJ = 25o C

0.1

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

0.01
0

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

400

NOTE 4
100

NOTES
(1) Case Temperature, TC, With Bridge Mounted on
3.2" Sq. x 0.12" Thick (8.2cm Sq. x 0.3cm)
Aluminum Plate
(2) TJ = 150o C
10
1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

E30

(3) TJ = 25o C; Pulse Width = 300Sec; 1% Duty Cycle

(4) TJ = 25o C; f = 1 MHz; Vsig = 50mVp-p

3.1 08sbu

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-800-1C

ABDB-800-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

ACTUAL SIZE
DT
DB804

SERIES DB800-DB810 and ADB804-ADB808

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

BH
AC

SURGE OVERLOAD RATING TO 300 AMPS PEAK

AC

UL RECOGNIZED - FILE #E124962

LL
_

MECHANICAL DATA

LD

Case: Molded plastic, U/L Flammability Rating 94V-0

D1

Terminals: Round silver plated copper pins

+
Soldering: Per MIL-STD 202 Method 208 guaranteed
D1

BL

Polarity: Marked on side of case; positive lead at beleveled corner

_
Mounting Position: Any. Through hole provided for #6 screw
Weight: 0.18 Ounces (5.4 Grams)

BL

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratingsat25Cambienttemperature unlessotherwisespecified.
Single phase, half wave,60Hz, resistive or inductive load.
Forcapacitive loads, derate currentby20%.

RATINGS

PARAMETER (TEST CONDITIONS)

SYMBOL

Series Number
Maximum DC Blocking Voltage

VRM

Working Peak Reverse Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

VRRM

RMS Reverse Voltage

VR (RMS)

CONTROLLED
AVALANCHE
ADB ADB ADB DB
804 806 808 800

DB DB DB
801 802 804

DB
806

DB DB
808 810

400

600 800

50

100

200

400

600

800 1000 VOLTS

280

420 560

35

70

140

280

420

560

Power Dissipation in V(BR) Region for 100 S Square Wave

PRM

400

n/a

Continuous Power Dissipation in V(BR) Region

@ THS=80o C (Heat Sink Temp)

PR

n/a

Thermal Energy (Rating for Fusing)

I2t

64

IFSM

300

IO

10
8

TJ, TSTG

-55 to +150

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 150O C
@ TC = 50o C (Note 1)
Average Forward Rectified Current
@TA = 50o C (Note 2)
Junction Operating and Storage Temperature Range

AMPS2
SEC
AMPS

V(BR) Min

450

850

n/a

Maximum Avalanche Voltage

V(BR) Max

900 1100 1300

n/a

Maximum Reverse Current at Rated V RM

@ TA = 25o C
@TA = 100o C

Minimum Insulation Breakdown Voltage (Circuit to Case)

Typical Thermal Resistance

Junction to Ambient (Note 2)

Junction to Case (Note 1)

700

WATTS

Minimum Avalanche Voltage

Maximum Forward Voltage (Per Diode) at 4 Amps DC

UNITS

NON-CONTROLLED
AVALANCHE

650

VFM

0.95 (Typ. 0.90)

IRM

5
1

VISO

2000

RJA
RJC

12
5

NOTES: (1) Bridge mounted on 4.9" x 4.3" x 0.11" thick (12.4cm x 10.8cm x 0.3cm) aluminum plate
(2) Bridge mounted on PC Board with 0.5" sq. (12mm sq.) copper pads and bridge lead length of 0.375" (9.5mm)
(3) Bolt bridge on heat sink, using silicon thermal compound between bridge and mounting surface, for maximum heat transfer.

VOLTS
A
mA
VOLTS
o

C/W
3.01 08db

E31

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-800-2C

ABDB-800-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

8 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES DB800 - DB810 and SERIES ADB804 - ADB808
300

60Hz Resistive or Inductive Loads

250

NOTE 1

200

Case

150

Ambient

NOTE 2
100

50

10

100

Number of Cycles at 60 Hz

Temperature, oC
FIGURE 1. FORWARD CURRENT DERATING CURVE

100

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

50

10
10

TJ = 100o C

1.0

1.0

NOTE 3
0.1

0.1

TJ = 25o C

0.01

0.01

20

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

400

NOTE 4

NOTES
(1) Case Temperature, TC, With Bridge Mounted on
4.9" x 4.3" x 0.11" Thick (12.4cm x 10.8cm x 0.3cm)
Aluminum Plate

100

Ambient Temperature, TA, With Bridge Mounted on

PC Board With 0.5" Sq. (12mm Sq.) Copper Pads
And Bridge Lead Length of 0.375" (9.5mm)
(2) TJ = 150o C

10
1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

(3) TJ = 25 C; Pulse Width = 300Sec; 1% Duty Cycle

o

(4) TJ = 25o C; f = 1 MHz; Vsig = 50mVp-p

3.01 08db

E32

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-1000-1C

ABDB-1000-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

ACTUAL SIZE
DT
DB1004

SERIES DB1000-DB1010 and ADB1004-ADB1008

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

BH
AC

SURGE OVERLOAD RATING TO 300 AMPS PEAK

AC

UL RECOGNIZED - FILE #E124962

LL
_

MECHANICAL DATA

LD

Case: Molded plastic, U/L Flammability Rating 94V-0

D1

Terminals: Round silver plated copper pins

+
Soldering: Per MIL-STD 202 Method 208 guaranteed
D1

BL

Polarity: Marked on side of case; positive lead at beleveled corner

_
Mounting Position: Any. Through hole provided for #6 screw
Weight: 0.18 Ounces (5.4 Grams)

BL

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratingsat25Cambienttemperature unlessotherwisespecified.
Single phase, half wave,60Hz, resistive or inductive load.
Forcapacitive loads, derate currentby20%.

RATINGS

PARAMETER (TEST CONDITIONS)

SYMBOL

CONTROLLED
AVALANCHE

ADB ADB ADB DB DB DB DB DB DB DB

1004 1006 1008 1000 1001 1002 1004 1006 1008 1010

Series Number
Maximum DC Blocking Voltage

VRM

Working Peak Reverse Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

VRRM

RMS Reverse Voltage

VR (RMS)

400

600 800

50

100

200

400

600

800 1000 VOLTS

280

420 560

35

70

140

280

420

560

Power Dissipation in V(BR) Region for 100 S Square Wave

PRM

500

n/a

Continuous Power Dissipation in V(BR) Region

@ THS=80o C (Heat Sink Temp)

PR

n/a

Thermal Energy (Rating for Fusing)

I2t

64

IFSM

300

IO

10
8

TJ, TSTG

-55 to +150

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 150O C
@ TC = 50 C (Notes 1, 3)
@ TA = 50o C (Note 2)
Junction Operating and Storage Temperature Range

AMPS2
SEC
AMPS

Minimum Avalanche Voltage

V(BR) Min

450

850

n/a

Maximum Avalanche Voltage

V(BR) Max

900 1100 1300

n/a

Maximum Forward Voltage (Per Diode) at 5 Amps DC

Maximum Reverse Current at Rated V RM

@ TA = 25o C
@TA = 100o C

Minimum Insulation Breakdown Voltage (Circuit to Case)

Junction to Ambient (Note 2)
Junction to Case (Note 1)

700

WATTS

Average Forward Rectified Current

Typical Thermal Resistance

UNITS

NON-CONTROLLED
AVALANCHE

650

VFM

0.95 (Typ. 0.90)

IRM

5 (Typical < 0.5A)

0.5

VISO

2000

RJA
RJC

12
5

VOLTS
A
mA
VOLTS
o

C/W
3.01 10db

NOTES: (1) Bridge mounted on 5.1" x 4.3" x 0.11" thick (12.9cm x 10.8cm x 0.3cm) aluminum plate
(2) Bridge mounted on PC Board with 0.5" sq. (12mm sq.) copper pads and bridge lead length of 0.375" (9.5mm)
(3) Bolt bridge on heat sink with #6 screw, using silicon thermal compound between bridge and mounting surface for maximum heat transfer.

E33

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-1000-2C

ABDB-1000-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

10 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES DB1000 - DB1010 and SERIES ADB1004 - ADB1008
Resistive and Inductive Loads

300

250

Case

200

Ambient

150

NOTE 1
100

50
1

10

100

Number of Cycles at 60 Hz

Temperature, oC
FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

50

100

10
10

TJ = 100o C
1.0

1.0

NOTE 3
0.1

TJ = 25o C

0.1

0.01

0.01

20

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

40

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

400

NOTES

NOTE 4

(1) Case Temperature, TC, With Bridge Mounted on

5.1" x 4.3" x 0.11" Thick (12.9cm x 10.8cm x 0.3cm)
Aluminum Plate

100

Ambient Temperature, TA, With Bridge Mounted on

PC Board With 0.5" Sq. (12mm Sq.) Copper Pads
And Bridge Lead Length of 0.375" (9.5mm)
(2) TJ = 150o C
10
10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

E34

(3) TJ = 25 C; Pulse Width = 300Sec; 1% Duty Cycle

o

(4) TJ = 25o C; f = 1 MHz; Vsig = 50mVp-p

3.01 10db

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-1500-1C

ADBD-1500-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

SERIES: DB1500 - DB1510 and ADB1504 - ADB1508

Metal Case (Top & Sides)
Electrically Isolated

BH

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

BH

AC

LT

AC

ELECTRICALLY ISOLATED METAL CASE FOR

MAXIMUM HEAT DISSIPATION

LL
_

HOLE FOR
#8 SCREW

D1

UL RECOGNIZED - FILE #E141956

MECHANICAL DATA

LD

AC

D1

AC

D3

AC

AC

BL D1

BL

D2

Case: Metal (Potting epoxy carries U/L flammability Rating 94V-0)

D2

Terminals: Round silver plated copper pins or fast-on terminals

D1
BL

BL

Soldering: Per MIL-STD 202 Method 208 guaranteed (Note 1)

Polarity: Marked on side of case
Mounting Position: Any. Through hole for #8 screw.
Max. mounting torque = 20 in-lb.
Weight: Fast-on Terminals - 1.1 Ounces (31.6 Grams)
Wire Leads - 0.95 Ounce (28.5 Grams)
Suffix "T" indicates FAST-ON TERMINALS

Suffix "W" indicates WIRE LEADS

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.

RATINGS

PARAMETER (TEST CONDITIONS)

SYMBOL

CONTROLLED
AVALANCHE

UNITS

NON-CONTROLLED
AVALANCHE

ADB ADB ADB DB DB DB DB DB DB DB

1504 1506 1508 1500 1501 1502 1504 1506 1508 1510

Series Number
Maximum DC Blocking Voltage

VRM

Working Peak Reverse Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

VRRM

RMS Reverse Voltage

VR (RMS)

400

600 800

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 150O C.
o

Average Forward Rectified Current @ TC = 50 C.

100

200

400

280

420 560

35

70

140

It

375

IFSM

300

IO

15
-55 to +150

280

TJ, TSTG
V(BR) Min

450

850

n/a

Maximum Avalanche Voltage

V(BR) Max

900 1100 1300

n/a

560

700

VOLTS

VFM

1.03

IRM

1
10

VISO

2000

VOLTS

RJC

1.8

Typical Thermal Resistance, Junction to Case

650

420

AMPS

Junction Operating and Storage Temperature Range

@ TA = 25 C
Maximum Reverse Current at Rated VRM
@TA = 125o C
Minimum Insulation Breakdown Voltage (Circuit to Case)

800 1000

AMPS2
SEC

Mimimum Avalanche Voltage

Maximum Forward Voltage (Per Diode) at 7.5 Amps DC

600

VOLTS

Rating for Fusing (Non Repetitive; 1mS < t < 8.3mS)

50

C/W
3.0115dbm

E35

Data Sheet No. BRDB-1500-2C

ABDB-1500-2C

DIOTEC ELECTRONICS CORP.

18020 Hobart Blvd., Unit B
Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

15 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES DB1500 - DB1510 and SERIES ADB1504 - ADB1508

60Hz
Resistive or Inductive Loads

400

TJ = 150o C

300

200

Bridge Mounted on 5 x 4 x 3" Thick

(12.7 x 10.2 x 7.6cm) Finned Al. Plate

100

60

10

Number of Cycles at 60 Hz

Case Temperature, oC
FIGURE 1. FORWARD CURRENT DERATING CURVE

1000

100

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10

100

TJ = 125O C
1.0

10

1.0

TJ = 25o C
Pulse Width = 300Sec
1%Duty Cycle

0.1

0.1

TJ = 25O C

.01
0

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

E36

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

4.97bbrdb15p

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-1500P-1C

ADBD-1500P-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

SERIES: DB1500P - DB1510P and ADB1504P - ADB1508P

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Suffix "P" indicates molded PLASTIC with integrally mounted Heat Sink

Heat Sink
BH

BH

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE
Molded
Body

INTEGRALLY MOLDED HEAT SINK PROVIDES VERY

LOW THERMAL RESISTANCE FOR MAXIMUM HEAT
DISSIPATION

LT

TopView of
HeatSink

HOLE FOR
#8 SCREW

D1

Molded
Body

LL

HOLE FOR
#8SCREW

LD

UL RECOGNIZED - FILE #E141956

AC

AC

D1

D3 BL

Case: Molded plastic, U/L Flammability Rating 94V-0

AC

BL D1

AC

AC

AC

D2
BL

Terminals: Round silver plated copper pins or fast-on terminals

D2

MECHANICAL DATA

D1
BL

Soldering: Per MIL-STD 202 Method 208 guaranteed (Note 1)

Polarity: Marked on side of case
Mounting Position: Any. Through hole for #8 screw.
Max. mounting torque = 20 in-lb.
Weight: Fast-on Terminals - 0.7 Ounces (20.0 Grams)
Wire Leads - 0.55 Ounce (16.0 Grams)
Suffix "T" indicates FAST-ON TERMINALS

Suffix "W" indicates WIRE LEADS

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.

RATINGS

PARAMETER (TEST CONDITIONS)

SYMBOL

CONTROLLED
AVALANCHE

UNITS

NON-CONTROLLED
AVALANCHE

ADB ADB ADB DB

DB DB DB
DB
DB
DB
1504P 1506P 1508P 1500P 1501P 1502P 1504P 1506P 1508P 1510P

Series Number
Maximum DC Blocking Voltage

VRM

Working Peak Reverse Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

VRRM

RMS Reverse Voltage

VR (RMS)

Rating for Fusing (Non Repetitive; 1mS < t < 8.3mS)

400

600 800

Average Forward Rectified Current @ TC = 50 C

100

200

400

280

420 560

35

70

140

It

375

IFSM

300

IO

15
-55 to +150

280

TJ, TSTG
V(BR) Min

450

850

n/a

Maximum Avalanche Voltage

V(BR) Max

900 1100 1300

n/a

560

700

VOLTS

VFM

1.03

IRM

1
10

VISO

2500

VOLTS

RJC

1.4

Typical Thermal Resistance, Junction to Case

650

420

AMPS

Junction Operating and Storage Temperature Range

@ TA = 25 C
Maximum Reverse Current at Rated VRM
@TA = 125o C
Minimum Insulation Breakdown Voltage (Circuit to Case)

800 1000

AMPS2
SEC

Mimimum Avalanche Voltage

Maximum Forward Voltage (Per Diode) at 7.5 Amps DC

600

VOLTS

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 150O C

50

C/W
3.0115dbp

E37

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-1500P-2B

ABDB-1500P-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

15 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES DB1500P - DB1510P and SERIES ADB1504P - ADB1508P

60Hz
Resistive and Inductive Loads

400

TJ = 150o C
300

200

Bridge Mounted on 5 x 4 x 3" Thick

(12.7 x 10.2 x 7.6cm) Finned Al. Plate

100

60

10

Case Temperature, C
FIGURE 1. FORWARD CURRENT DERATING CURVE

1000

100

Number of Cycles at 60 Hz

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10

100

TJ = 125O C
1.0

10

1.0

TJ = 25o C
Pulse Width = 300Sec
1%Duty Cycle

0.1

0.1

TJ = 25O C

.01
0

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

E38

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

3.01 15dbp

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-2500-1C

ADBD-2500-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

SERIES: DB2500 - DB2510 and ADB2504 - ADB2508

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Metal Case (Top & Sides)

Electrically Isolated

BH

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

BH

LT
LL

ELECTRICALLY ISOLATED METAL CASE FOR

MAXIMUM HEAT DISSIPATION

HOLE FOR
#8 SCREW

D1

UL RECOGNIZED - FILE #E141956

MECHANICAL DATA

LD

AC

D1

AC

BL D1

D3 BL

AC

AC

Case: Metal (Potting epoxy carries U/L flammability Rating 94V-0)

D2

AC

D2

Terminals: Round silver plated copper pins or fast-on terminals

D1
BL

AC

BL

Soldering: Per MIL-STD 202 Method 208 guaranteed (Note 1)

Polarity: Marked on side of case
Mounting Position: Any. Through hole for #8 screw.
Max. mounting torque = 20 in-lb.
Weight: Fast-on Terminals - 1.1 Ounces (31.6 Grams)
Wire Leads - 0.95 Ounce (28.5 Grams)
Suffix "T" indicates FAST-ON TERMINALS

Suffix "W" indicates WIRE LEADS

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.

RATINGS

PARAMETER (TEST CONDITIONS)

SYMBOL

CONTROLLED
AVALANCHE

UNITS

NON-CONTROLLED
AVALANCHE

ADB ADB ADB DB DB DB DB DB DB DB

2504 2506 2508 2500 2501 2502 2504 2506 2508 2510

Series Number
Maximum DC Blocking Voltage

VRM

Working Peak Reverse Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

VRRM

RMS Reverse Voltage

VR (RMS)

Rating for Fusing (Non Repetitive; 1mS < t < 8.3mS)

400

600 800

Average Forward Rectified Current @ Tc = 50 C

100

200

400

280

420 560

35

70

140

It

375

IFSM

300

IO

25
-55 to +150

280

TJ, TSTG
V(BR) Min

450

850

n/a

Maximum Avalanche Voltage

V(BR) Max

900 1100 1300

n/a

560

700

VOLTS

VFM

1.03

IRM

1
10

VISO

2000

VOLTS

RJC

1.6

Typical Thermal Resistance, Junction to Case

650

420

AMPS

Junction Operating and Storage Temperature Range

@ TA = 25 C
Maximum Reverse Current at Rated VRM
@TA = 125o C
Minimum Insulation Breakdown Voltage (Circuit to Case)

800 1000

AMPS2
SEC

Mimimum Avalanche Voltage

Maximum Forward Voltage (Per Diode) at 12.5 Amps DC

600

VOLTS

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 150O C

50

C/W
3.0125dbm

E39

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-2500-2B

ABDB-2500-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

25 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES DB2500 - DB2510 and SERIES ADB2504 - ADB2508

400

TJ = 150o C

300

60Hz Resistive or
Inductive Loads

200

100

Bridge Mounted on 5 x 6 x 4.9" Thick

(12.7 x 15.2 x 12.4cm) Finned Al. Plate
60

10

Number of Cycles at 60 Hz

Case Temperature, oC
FIGURE 1. FORWARD CURRENT DERATING CURVE

1000

100

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10

100

TJ = 125O C
1.0

10

1.0

TJ = 25o C
Pulse Width = 300Sec
1%Duty Cycle

0.1

0.1

TJ = 25O C

.01
0

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

E40

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

3.01 25dbm

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-2500P-1C

ADBD-2500P-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

SERIES: DB2500P - DB2510P and ADB2504P - ADB2508P

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Suffix "P" indicates molded PLASTIC with integrally mounted Heat Sink

Heat Sink
BH

BH

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

LT

Molded
Body

INTEGRALLY MOLDED HEAT SINK PROVIDES VERY

LOW THERMAL RESISTANCE FOR MAXIMUM HEAT
DISSIPATION

LL

TopView of
HeatSink

HOLE FOR
#8 SCREW

D1

Molded
Body

HOLE FOR
#8SCREW

LD

UL RECOGNIZED - FILE #E141956

AC

+
D1

AC

AC

BL D1

AC

AC

Case: Molded plastic, U/L Flammability Rating 94V-0

AC

D3 BL

MECHANICAL DATA

D2
BL

Terminals: Round silver plated copper pins or fast-on terminals

D2

D1
BL

Soldering: Per MIL-STD 202 Method 208 guaranteed (Note 1)

Polarity: Marked on side of case
Mounting Position: Any. Through hole for #8 screw.
Max. mounting torque = 20 in-lb.
Weight: Fast-on Terminals - 0.7 Ounces (20.0 Grams)
Wire Leads - 0.55 Ounce (16.0 Grams)
Suffix "T" indicates FAST-ON TERMINALS

Suffix "W" indicates WIRE LEADS

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.

RATINGS

PARAMETER (TEST CONDITIONS)

SYMBOL

CONTROLLED
AVALANCHE

UNITS

NON-CONTROLLED
AVALANCHE

ADB ADB ADB DB

DB
DB
DB
DB
DB
DB
2504P 2506P 2508P 2500P 2501P 2502P 2504P 2506P 2508P 2510P

Series Number
Maximum DC Blocking Voltage

VRM

Working Peak Reverse Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

VRRM

RMS Reverse Voltage

VR (RMS)

Rating for Fusing (Non Repetitive; 1mS < t < 8.3mS)

400

600 800

Average Forward Rectified Current @ TC = 50 C

100

200

400

600

800 1000

VOLTS
280

420 560

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 150O C

50

35

70

140

It

373

IFSM

300

IO

25
-55 to +150

280

560

700

AMPS2
SEC
AMPS

Junction Operating and Storage Temperature Range

TJ, TSTG

Mimimum Avalanche Voltage

V(BR) Min

450

850

n/a

Maximum Avalanche Voltage

V(BR) Max

900 1100 1300

n/a

650

420

VOLTS

VFM

1.03

IRM

1
10

Minimum Insulation Breakdown Voltage (Circuit to Case)

VISO

2500

VOLTS

Typical Thermal Resistance, Junction to Case

RJC

1.2

Maximum Forward Voltage (Per Diode) at 12.5 Amps DC

o

Maximum Reverse Current at Rated VRM

@ TA = 25 C
@TA = 125o C

C/W
3.0125dbp

E41

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-2500P-2C

ABDB-2500P-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

25 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES DB2500P - DB2510P and SERIES ADB2504P - ADB2508P

400

60Hz Resistive or Inductive Loads

TJ = 150o C
300

200

100

Bridge Mounted on 5 x 6 x 4.9" Thick

(12.7 x 15.2 x 12.4cm) Finned Al. Plate
60

10

Case Temperature, C
FIGURE 1. FORWARD CURRENT DERATING CURVE

1000

100

Number of Cycles at 60 Hz

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10

100

TJ = 125O C
1.0

10

1.0

TJ = 25o C
Pulse Width = 300Sec
1%Duty Cycle

0.1

0.1

TJ = 25O C

.01
0

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

E42

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

3.01 25db

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-3500-1C

ADBD-3500-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

SERIES: DB3500 - DB3510 and ADB3504 - ADB3508

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Metal Case (Top & Sides)

Electrically Isolated

BH

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

BH

LT
LL

ELECTRICALLY ISOLATED METAL CASE FOR

MAXIMUM HEAT DISSIPATION

HOLE FOR
#8 SCREW

D1

UL RECOGNIZED - FILE #E141956

MECHANICAL DATA

LD

AC

D1

AC

D3

AC

BL D1

BL

Case: Metal (Potting epoxy carries U/L flammability Rating 94V-0)

AC

D2

AC

D2

Terminals: Round silver plated copper pins or fast-on terminals

AC

BL

D1
BL

Soldering: Per MIL-STD 202 Method 208 guaranteed (Note 1)

Polarity: Marked on side of case
Mounting Position: Any. Through hole for #8 screw.
Max. mounting torque = 20 in-lb.
Weight: Fast-on Terminals - 1.1 Ounces (31.6 Grams)
Wire Leads - 0.95 Ounce (28.5 Grams)
Suffix "T" indicates FAST-ON TERMINALS

Suffix "W" indicates WIRE LEADS

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.

RATINGS

PARAMETER (TEST CONDITIONS)

SYMBOL

CONTROLLED
AVALANCHE

UNITS

NON-CONTROLLED
AVALANCHE

ADB ADB ADB DB DB DB DB DB DB DB

3504 3506 3508 3500 3501 3502 3504 3506 3508 3510

Series Number
Maximum DC Blocking Voltage

VRM

Working Peak Reverse Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

VRRM

RMS Reverse Voltage

VR (RMS)

Rating for Fusing (Non Repetitive; 1mS < t < 8.3mS)

400

600 800

Average Forward Rectified Current @ TC = 50 C

100

200

400

600

800 1000

VOLTS
280

420 560

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 150O C

50

35

70

140

It

664

IFSM

400

IO

35
-55 to +150

280

560

700

AMPS2
SEC
AMPS

Junction Operating and Storage Temperature Range

TJ, TSTG

Mimimum Avalanche Voltage

V(BR) Min

450

850

n/a

Maximum Avalanche Voltage

V(BR) Max

900 1100 1300

n/a

650

420

VOLTS

VFM

1.03

IRM

1
10

Minimum Insulation Breakdown Voltage (Circuit to Case)

VISO

2000

VOLTS

Typical Thermal Resistance, Junction to Case

RJC

1.6

Maximum Forward Voltage (Per Diode) at 17.5 Amps DC

o

Maximum Reverse Current at Rated VRM

@ TA = 25 C
@TA = 125o C

C/W
3.0135dbm

E43

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-3500-2C

ABDB-3500-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

35 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES DB3500 - DB3510 and SERIES ADB3504 - ADB3508

60Hz Resistive or Inductive Loads

400

300

Bridge Mounted on 9 x 3 x 4.6" Thick

(22.9 x 7.6 x 11.7cm) Finned Al. Plate
200

TJ = 150o C

100

60

10

Number of Cycles at 60 Hz

Case Temperature, o C
FIGURE 1. FORWARD CURRENT DERATING CURVE

100

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10
1000

TJ = 125O C

100

1.0

10

0.1

1.0

TJ = 25o C
Pulse Width = 300Sec
1%Duty Cycle

TJ = 25 C

.01

0.1

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

Instantaneous
Forward
Voltage (Volts)
FIGURE 3. TYPICAL
FORWARD
CHARACTERISTIC
PER DIODE

E44

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

3.01 35dbm

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-3500P-1C

ADBD-3500P-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

SERIES: DB3500P - DB3510P and ADB3504P - ADB3508P

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Suffix "P" indicates molded PLASTIC with integrally mounted Heat Sink

Heat Sink
BH

BH

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

LT

Molded
Body

INTEGRALLY MOLDED HEAT SINK PROVIDES VERY

LOW THERMAL RESISTANCE FOR MAXIMUM HEAT
DISSIPATION

TopView of
HeatSink

HOLE FOR
#8 SCREW

D1

Molded
Body

LL

HOLE FOR
#8SCREW

LD

UL RECOGNIZED - FILE #E141956

AC

+
D1

AC

AC

BL D1

AC

AC

Case: Molded plastic, U/L Flammability Rating 94V-0

AC

D3 BL

D2
BL

Terminals: Round silver plated copper pins or fast-on terminals

D2

MECHANICAL DATA

D1
BL

Soldering: Per MIL-STD 202 Method 208 guaranteed

Polarity: Marked on side of case
Mounting Position: Any. Through hole for #8 screw.
Max. mounting torque = 20 in-lb.
Weight: Fast-on Terminals - 0.7 Ounces (20.0 Grams)
Wire Leads - 0.55 Ounces (16.0 Grams)
Suffix "T" indicates FAST-ON TERMINALS

Suffix "W" indicates WIRE LEADS

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.

RATINGS

PARAMETER (TEST CONDITIONS)

SYMBOL

CONTROLLED
AVALANCHE

UNITS

NON-CONTROLLED
AVALANCHE

ADB ADB ADB DB

DB DB DB
DB
DB
DB
3504P 3506P 3508P 3500P 3501P 3502P 3504P 3506P 3508P 3510P

Series Number
Maximum DC Blocking Voltage

VRM

Working Peak Reverse Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

VRRM

RMS Reverse Voltage

VR (RMS)

Rating for Fusing (Non Repetitive; 1mS < t < 8.3mS)

400

600 800

Average Forward Rectified Current @ TC = 50 C

100

200

400

280

420 560

35

70

140

It

664

IFSM

400

IO

35
-55 to +150

280

TJ, TSTG
V(BR) Min

450

850

n/a

Maximum Avalanche Voltage

V(BR) Max

900 1100 1300

n/a

560

700

VOLTS

VFM

1.03

IRM

1
10

VISO

2500

VOLTS

RJC

1.2

Typical Thermal Resistance, Junction to Case

650

420

AMPS

Junction Operating and Storage Temperature Range

@ TA = 25 C
Maximum Reverse Current at Rated VRM
@TA = 125o C
Minimum Insulation Breakdown Voltage (Circuit to Case)

800 1000

AMPS2
SEC

Mimimum Avalanche Voltage

Maximum Forward Voltage (Per Diode) at 17.5 Amps DC

600

VOLTS

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 150O C

50

C/W
3.0135dbp

E45

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-3500P-2C

ABDB-3500P-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

35 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES DB3500P - DB3510P and SERIES ADB3504P - ADB3508P

60Hz Resistive or Inductive Loads

400

300

Bridge Mounted on 9 x 3 x 4.6" Thick

(22.9 x 7.6 x 11.7cm) Finned Al. Plate
200

TJ = 150o C

100

60

10

Case Temperature, C
FIGURE 1. FORWARD CURRENT DERATING CURVE

1000

100

Number of Cycles at 60 Hz

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10

100

TJ = 125O C
1.0

10

1.0

TJ = 25o C
Pulse Width = 300Sec
1%Duty Cycle

0.1

0.1

TJ = 25O C

.01
0

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

E46

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

3.01 35dbp

DIOTEC ELECTRONICS CORP.

Data Sheet No. BSDB-4000-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)
BUILT-IN STRESS RELIEF MECHANISM FOR
SUPERIOR RELIABILITY AND PERFORMANCE

SDB PACKAGE SHOWN ACTUAL SIZE

0.205 (5.2) Dia Through

Hole for #8 Screw

BW

BL

INTEGRALLY MOLDED HEAT SINK PROVIDES VERY

LOW THERMAL RESISTANCE FOR MAXIMUM HEAT
TRANSFER

BL
-

SPACE SAVING IN-LINE DESIGN FOR PRINTED

CIRCUIT BOARD APPLICATIONS
HEAT
SINK

UL RECOGNIZED - FILE #E124962

AC

LM LL

MECHANICAL DATA

LS LS LS

LD
LO

Case: Molded plastic, U/L Flammability Rating 94V-0

MILLIMETERS

Terminals: Round silver plated pins

SYM
BL

Soldering: Per MIL-STD 202 Method 208 guaranteed

BW

Polarity: Marked on case

LD
LL

Mounting Position: Any. Bolt down on heatsink

Maximum mounting torque = 20 in. lb.

LM
LO
LS

Weight: 0.6 Ounces (17 Grams)

INCHES

MIN

MAX

MIN

MAX

28.4

28.7

1.12
n/a

0.405

10.3
n/a
1.27 Typ
15.9

1.13

0.050 Typ
0.625
n/a

n/a

19.0
n/a
3.175 Nom
5.08 Typ

0.750

n/a

0.125 Nom
0.200 Typ

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Maximum DC Blocking Voltage

VRM

SDB
4000
50

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Series Number

Average Forward Rectified Current @ TC = 55 oC

Peak Forward Surge Current. Single 60Hz Half-Sine Wave
O
Superimposed on Rated Load (JEDEC Method). TJ = 175 C
Forward Voltage (Per Diode) at 20 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

Max.
Typ.
@ TA = 25o C
@ TA = 125o C

SDB
4001
100

UNITS

SDB
4002
200

SDB
4004
400

SDB
4006
600

SDB
4008
800

IO

40

IFSM

500

VFM

0.96
0.93

SDB
4010
1000
VOLTS

AMPS
1.00
0.97

VOLTS

IRM

2
20

Minimum Insulation Breakdown Voltage (Circuit to Case)

VISO

2500

VOLTS

Typical Thermal Resistance, Junction to Case

RJC

1.1

C/W

TJ, TSTG

-55 to +175

Junction Operating and Storage Temperature Range

3.01 40sdb

E47

DIOTEC ELECTRONICS CORP.

Data Sheet No. BSDB-4000-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

40 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SDB4000-4010 SERIES

1000

Bridge Mounted on 8.4" x 4" x 4.6" Thick

(221.3cm x 10.2cm x 11.7cm) Finned Al. Plate

TJ = 175o C

60Hz Resistive
or
Inductive Loads
100

Case Temperature, C
FIGURE 1. FORWARD CURRENT DERATING CURVE

1000

60
1

10

100

Number of Cycles at 60 Hz

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10

SDB4000-SDB4006

100
O

TJ = 125 C
1.0

SDB4008-SDB4010
10

0.1

1.0

TJ = 25 oC
Pulse Width = 300 S
1% Duty Cycle

0.1

TJ = 25O C

.01
0

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

E48

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

3.01 40sdb

DIOTEC ELECTRONICS CORP.

Data Sheet No. BSDB-5000-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)
BUILT-IN STRESS RELIEF MECHANISM FOR
SUPERIOR RELIABILITY AND PERFORMANCE

SDB PACKAGE SHOWN ACTUAL SIZE

0.205 (5.2) Dia Through

Hole for #8 Screw

BW

BL

INTEGRALLY MOLDED HEAT SINK PROVIDES VERY

LOW THERMAL RESISTANCE FOR MAXIMUM HEAT
TRANSFER

BL
-

SPACE SAVING IN-LINE DESIGN FOR PRINTED

CIRCUIT BOARD APPLICATIONS
HEAT
SINK

UL RECOGNIZED - FILE #E124962

AC

LM LL

MECHANICAL DATA

LS LS LS

LD
LO

Case: Molded plastic, U/L Flammability Rating 94V-0

MILLIMETERS

Terminals: Round silver plated pins

SYM
BL

Soldering: Per MIL-STD 202 Method 208 guaranteed

BW

Polarity: Marked on case

LD
LL

Mounting Position: Any. Bolt down on heatsink

Maximum mounting torque = 20 in. lb.

LM
LO
LS

Weight: 0.6 Ounces (17 Grams)

INCHES

MIN

MAX

MIN

MAX

28.4

28.7

1.12
n/a

0.405

10.3
n/a
1.27 Typ
15.9

1.13

0.050 Typ
0.625
n/a

n/a

19.0
n/a
3.175 Nom
5.08 Typ

0.750

n/a

0.125 Nom
0.200 Typ

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Maximum DC Blocking Voltage

VRM

SDB
5000
50

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Series Number

Average Forward Rectified Current @ TC = 55o C

Peak Forward Surge Current. Single 60Hz Half-Sine Wave
O
Superimposed on Rated Load (JEDEC Method). TJ = 175 C
Forward Voltage (Per Diode) at 20 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

Max.
Typ.
@ TA = 25o C
@ TA = 125o C

SDB
5001
100

UNITS

SDB
5002
200

SDB
5004
400

SDB
5006
600

SDB
5008
800

IO

50

IFSM

600

VFM

0.96
0.93

SDB
5010
1000
VOLTS

AMPS
1.00
0.97

VOLTS

IRM

2
20

MinimumInsulation Breakdown Voltage (Circuit to Case)

VISO

2500

VOLTS

Typical Thermal Resistance, Junction to Case

RJC

1.10

C/W

TJ, TSTG

-55 to +175

Junction Operating and Storage Temperature Range

3.0150sdb

E49

DIOTEC ELECTRONICS CORP.

Data Sheet No. BSDB-5000-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

50 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES SDB5000 - SDB5010

700

Resistive and Inductive Loads

600
500
400

300

200

TJ = 175o C
100

10

Case Temperature, C
FIGURE 1. FORWARD CURRENT DERATING CURVE

1000

100

Number of Cycles at 60 Hz

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10

SDB5000-SDB5006

100
O

TJ = 125 C
1.0

SDB5008-SDB5010
10

0.1

TJ = 25O C

1.0

TJ = 25 oC
Pulse Width = 300 S
1% Duty Cycle
0.1

.01
0

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

E50

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

3.0150sdb

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-5000P-1B

ADBD-5000P-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

SERIES: DB5000P - DB5010P and ADB5004P - ADB5008P

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Suffix "P" indicates molded PLASTIC with integrally mounted Heat Sink

Heat Sink
BH

BH

BUILT-IN STRESS RELIEF MECHANISM FOR

SUPERIOR RELIABILITY AND PERFORMANCE

LT

Molded
Body

INTEGRALLY MOLDED HEAT SINK PROVIDES VERY

LOW THERMAL RESISTANCE FOR MAXIMUM HEAT
DISSIPATION

TopView of
HeatSink

HOLE FOR
#8 SCREW

D1

Molded
Body

LL

HOLE FOR
#8SCREW

LD

UL RECOGNIZED - FILE #E141956

AC

AC

D1

D3 BL

Case: Molded plastic, U/L Flammability Rating 94V-0

BL D1

AC

AC

AC

D2
BL

Terminals: Round silver plated copper pins or fast-on terminals

D2

AC

MECHANICAL DATA

D1
BL

Soldering: Per MIL-STD 202 Method 208 guaranteed

Polarity: Marked on side of case
Mounting Position: Any. Through hole for #8 screw.
Max. mounting torque = 20 in-lb.
Weight: Fast-on Terminals - 0.7 Ounces (20.0 Grams)
Wire Leads - 0.55 Ounce (16.0 Grams)
Suffix "T" indicates FAST-ON TERMINALS

Suffix "W" indicates WIRE LEADS

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.

RATINGS

PARAMETER (TEST CONDITIONS)

SYMBOL

CONTROLLED
AVALANCHE

UNITS

NON-CONTROLLED
AVALANCHE

ADB ADB ADB DB

DB DB DB
DB
DB
DB
5004P 5006P 5008P 5000P 5001P 5002P 5004P 5006P 5008P 5010P

Series Number
Maximum DC Blocking Voltage

VRM

Working Peak Reverse Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

VRRM

RMS Reverse Voltage

VR (RMS)

Rating for Fusing (Non-repetitive; 1mS < t < 8.3mS

400

600 800

Average Forward Rectified Current @ TC = 55 C

280

420 560

70

140

600

IO

50
-55 to +175

TJ, TSTG
450

Maximum Avalanche Voltage

V(BR) Max

900 1100 1300

VFM

400

600

800 1000

650

0.96
0.93

850

280

420

560

700

AMPS2
SEC

IFSM

V(BR) Min

@ TA = 25 C
@TA = 125o C

35

1000

Junction Operating and Storage Temperature Range

Forward Voltage Drop (Per Diode) at 20 Amps DC

200

It

Mimimum Avalanche Voltage

Max.
Typ.

100

VOLTS

Peak Forward Surge Current. Single 60Hz Half-Sine Wave

Superimposed on Rated Load (JEDEC Method). TJ = 175O C

50

AMPS
C
n/a

VOLTS

n/a

1.00
0.97

0.96
0.93

1.00
0.97

IRM

2
20

Minimum Insulation Breakdown Voltage (Circuit to Case)

VISO

2500

VOLTS

Typical Thermal Resistance, Junction to Case

RJC

1.10

Maximum Reverse Current at Rated VRM

C/W
3.01 50bdp

E51

DIOTEC ELECTRONICS CORP.

Data Sheet No. BRDB-5000P-2A

ABDB-5000P-2A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

50 AMP SILICON BRIDGE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES DB5000P - DB5010P and SERIES ADB5004P - ADB5008P

700

60Hz Resistive or Inductive Loads

600

TJ = 175o C

500
400

300

200

100

10

Case Temperature, C
FIGURE 1. FORWARD CURRENT DERATING CURVE

1000

100

Number of Cycles at 60 Hz

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10

ADB5004P-ADB5006P
DB5000P-DB5006P

100
O

TJ = 125 C
1.0

ADB5008P
DB5008P-DB5010P
10

0.1

1.0

TJ = 25 oC
Pulse Width = 300 S
1% Duty Cycle

0.1

TJ = 25O C

.01
0

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

E52

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

9.98bbrdb50p

SECTION F
RESERVED

DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

SECTION G
FAST RECOVERY
FULL WAVE
BRIDGE RECTIFIERS

DUAL IN-LINE PACKAGE

DT

FDI104

1 AMPERE
50 to 1000 VOLTS

CYLINDRICAL PACKAGE
1.5 AMPERES
50 to 1000 VOLTS

VERTICAL, SIDE LOOKING, PACKAGE

DT
FSB200
AC

2 AMPERES
50 to 1000 VOLTS

RECTANGULAR HORIZONTAL PACKAGE

DT
FDB306

3 to 6 AMPERES
50 to 1000 VOLTS

RECTANGULAR HORIZONTAL PACKAGES

25 to 35 AMPERES
50 to 1000 VOLTS

DIOTEC ELECTRONICS CORP. - 18020 Hobart Blvd., Unit B - Gardena, CA 90248 U.S.A. - PH: 310-767-1052 - FX: 310-767-7958

DIOTEC ELECTRONICS CORP.

Data Sheet No. FRDI-100-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
THE FDI PACKAGE

PRV Ratings from 50 to 1000 Volts

SERIES FDI100 - FDI110

_

Surge overload rating to 50 Amps peak

DT

DT

FDI104

A1

FDI104

Reliable low cost molded plastic construction

Ideal for printed circuit board applications

C
Fast switching for high efficiency

UL RECOGNIZED - FILE #E124962

L1
L

MECHANICAL DATA

B
B1

B2

Case: Molded plastic, U/L Flammability Rating 94V-0

Sym
Terminals: Rectangular pins
_

Soldering: Per MIL-STD 202 Method 208 guaranteed

A
A1
B
B1
B2
C
D
L
L1

Polarity: Marked on case

Mounting Position: Any

Weight: 0.05 Ounces (1.3 Grams)

Minimum
mm
in
0.290
7.4
0.245
6.2
0.41
0.016
0.195
5.0
0.300
7.6
9.3
0.355
0.125
3.2
3.9
0.155
0.060* 1.5*

Maximum
mm
in
8.9
0.310
6.5
0.255
0.51
0.020
0.205
5.2
8.9
0.350
9.3
0.365
3.4
0.135
0.165
4.3

* This dimension is "Typical".

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

UNITS

Maximum DC Blocking Voltage

VRM

FDI
100
50

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

VRRM

50

100

200

400

600

800

1000

Series Number

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ TA = 40 C

Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 1 Amp DC
@ TA = 25 C
@ TA = 100 oC

Maximum Reverse Recovery Time (Note 1)

@ TJ = 25 C

Maximum Thermal Resistance, Junction to Ambient (Note 2)

FDI
102
200

FDI
104
400

FDI
106
600

FDI
108
800

FDI
110
1000

VOLTS

IO

IFSM

50

VFM

1.3

VOLTS

IRM

10
1

A
mA

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage

Junction Operating and StorageTemperature Range

FDI
101
100

TRR

200

AMPS

300

500

nS

RJA

40

C/W

TJ, TSTG

-55 to +150

NOTES: (1)TJ=25 C, IF=0.5A, IR=1A, IRR=0.25A

(2)Thermal resistance from junction to ambient with bridge mounted on PC Board with 0.5" sq. (13mm sq.) copper pads

3.0101fdi

G1

DIOTEC ELECTRONICS CORP.

Data Sheet No. FRWB-150-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
WB PACKAGE

PRV Ratings from 50 to 1000 Volts

SERIES FWB150 - FWB1510

Surge overload rating to 45 Amps peak

Reliable low cost molded plastic construction

D

Ideal for printed circuit board applications

L
One (1)
Lead
(+)

Fast switching for high efficiency

UL RECOGNIZED - FILE #E141956

L1
Three (3)
Leads

MECHANICAL DATA
Case: Molded plastic, U/L Flammability Rating 94V-0

B1

Terminals: Round silver plated pins

MILLIMETERS
SYM

Soldering: Per MIL-STD 202 Method 208 guaranteed

Mounting Position: Any

Weight: 0.05 Ounces (1.3 Grams)

+
AC

INCHES

MIN

MAX

MIN

MAX

8.6
0.76

8.89
0.81

0.340
0.030

0.350
0.032

B1

4.6

5.6

0.180

0.220

D
L
L1

5.1
30.5
25.4

5.6
n/a
n/a

0.200
1.20
1.0

0.220
n/a
n/a

A
B

Polarity: Marked on case

B1

AC
-

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

UNITS

Maximum DC Blocking Voltage

VRM

FWB
150
50

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Series Number

Average Forward Rectified Current @ TC = 55 C

Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage (Per Diode) at 1 Amp DC
Maximum Average DC Reverse Current at Rated
DC Blocking Voltage (Per Bridge Element)

Thermal Energy (Rating for Fusing, t < 8.3 mS)

Typical Thermal Resistance, Junction to Ambient (Note 2)
Junction Operating and Storage Temperature Range
o

FWB
152
200

FWB
154
400

FWB
156
600

FWB
158
800

FWB
1510
1000
VOLTS

IO

1.5

IFSM

45

VFM

1.3

VOLTS

IRM

10
1

A
mA

@ TA = 25 C
@ TA = 100 o C

Maximum Reverse Recovery Time (Note 1)

FWB
151
100

TRR

200

AMPS

300

500

nS

6.6

AMPS2
SEC

RJA

40

C/W

TJ, TSTG

-55 to +150

I2t

NOTES: (1) TJ=25 C, IF=0.5A, IR=1A, IRR=0.25A

(2) Mounted on PC Board with 0.2" sq. (5.5mm sq.) copper pads and lead length of 0.375" (9.5mm)

3.011-5wb

G3

DIOTEC ELECTRONICS CORP.

Data Sheet No. BFSB-200-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

SERIES FSB200 - FSB210

ACTUAL SIZE OF
SB2 PACKAGE

PRV Ratings from 50 to 1000 Volts

Surge overload rating to 50 Amps peak

C
DIOTEC 009
FSB208

Reliable low cost molded plastic construction

D1

DIOTEC 009
FSB208

Ideal for printed circuit board applications

Fast switching for high efficiency
L

UL RECOGNIZED - FILE #E124962

B1

MECHANICAL DATA

A1
A

Case: Molded plastic, U/L Flammability Rating 94V-0

Terminals: Rectangular pins

MILLIMETERS
SYM

Soldering: Per MIL-STD 202 Method 208 guaranteed

MAX

MIN

MAX

5.99

7.01

0.236

0.276

A1

2.99

3.51

0.118

0.138

0.71

0.89

0.028

0.035

Mounting Position: Any

B1
C
D

3.55
16.0
14.0

4.00
18.0
15.0

0.140
0.63
0.55

0.160
0.71
0.59

Weight: 0.1 Ounces (2.8 Grams)

D1
L

13.2
12.7

13.7
n/a

0.52
0.50

0.54
n/a

Polarity: Marked on case

MIN

INCHES

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

UNITS

Maximum DC Blocking Voltage

VRM

FSB
200
50

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

VRRM

50

100

200

400

600

800

1000

Series Number

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ TA = 55 C

Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 1 Amp DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Maximum Reverse Recovery Time (Note 1)

FSB
202
200

FSB
204
400

FSB
206
600

FSB
208
800

FSB
210
1000

IO

IFSM

50

@ TJ = 25 C

Maximum Thermal Resistance, Junction to Ambient (Note 2)

NOTES: (1) TJ = 25 C, IF = 0.5A, IR = 1A, IRR = 0.25A

(2) Bridge mounted on PC Board with 0.47" sq. (12mm sq.) copper pads

VOLTS

AMPS

VFM

VOLTS

IRM

10
500

@ TA = 25 C
@ TA = 125 oC

Junction Operating and Storage Temperature Range

o

FSB
201
100

TRR

200

300

500

nS

RJA

30

C/W

TJ, TSTG

-55 to +150

C
3.0102fsb

G5

DIOTEC ELECTRONICS CORP.

Data Sheet No. FRDB-300-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
FDB PACKAGE

PRV Ratings from 50 to 1000 Volts

SERIES FDB300 - FDB310

DT
FDB306

Surge overload rating to 50 Amps peak

BH

Reliable low cost molded plastic construction

Ideal for printed circuit board applications

LL
Fast switching for high efficiency
LD

UL RECOGNIZED - FILE #E124962

D1

MECHANICAL DATA
AC

Case: Molded plastic, U/L Flammability Rating 94V-0

AC

D1
_

Terminals: Round silver plated copper pins

BL

Soldering: Per MIL-STD 202 Method 208 guaranteed

BL
Polarity: Marked on side of case; positive lead at beveled corner
Mounting Position: Any. Through hole provided for #6 screw
Weight: 0.11 Ounces (3.36 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

UNITS

Maximum DC Blocking Voltage

VRM

FDB
300
50

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Series Number

Average Forward Rectified Current @ TC = 50 C

Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage (Per Diode) at 1.5 Amps DC
Maximum Average DC Reverse Current at Rated
DC Blocking Voltage

Thermal Energy (Rating for Fusing, t < 8.3 mS)

Maximum Thermal Resistance, Junction to Case (Note 2)
Junction Operating and Storage Temperature Range
o

NOTES: (1) TJ=25 C, IF=0.5A, IR=1A, IRR=0.25A

(2) Bridge mounted on 4.0" sq. x 0.11" thick (10.5cm sq. x 0.3cm) aluminum plate

FDB
302
200

FDB
304
400

FDB
306
600

FDB
308
800

FDB
310
1000
VOLTS

IO

IFSM

50

VFM

1.3

VOLTS

IRM

10
1

A
mA

@ TA = 25 C
@ TA = 100 o C

Maximum Reverse Recovery Time (Note 1)

FDB
301
100

TRR

200

AMPS

300

500

nS

10

AMPS2
SEC

RJC

2.5

C/W

TJ, TSTG

-55 to +150

I2t

3.0103fdb

G7

DIOTEC ELECTRONICS CORP.

Data Sheet No. FRDB-600-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
FDB PACKAGE

PRV Ratings from 50 to 1000 Volts

SERIES FDB600 - FDB610

DT
FDB606

Surge overload rating to 90 Amps peak

Reliable low cost molded plastic construction

BH

Ideal for printed circuit board applications

LL

Fast switching for high efficiency

LD

UL RECOGNIZED - FILE #E124962

MECHANICAL DATA

D1

AC

Case: Molded plastic, U/L Flammability Rating 94V-0

AC

+
_

Terminals: Round silver plated copper pins

D1

BL
_

Soldering: Per MIL-STD 202 Method 208 guaranteed

BL

Polarity: Marked on side of case; positive lead at bevelled corner

Mounting Position: Any. Through hole provided for #6 screw
Weight: 0.11 Ounces (3.36 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Maximum DC Blocking Voltage

VRM

FDB
600
50

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Series Number

Average Forward Rectified Current @ TC = 50 oC

Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage (Per bridge Element) at 3 Amps DC
Maximum Average DC Reverse Current At Rated
DC Blocking Voltage (Per Bridge Element-Note 2)

Thermal Energy (Rating for Fusing, t < 8.3 mS)

Typical Thermal Resistance, Junction to Case (Note 2)
Junction Operating and Storage Temperature Range
o

NOTES: (1) TJ=25 C, IF=0.5A, IR=1A, IRR=0.25A

(2) Bridge mounted on 4.0" sq. x 0.11" thick (10.5cm sq. x 0.3cm) aluminum plate

FDB
602
200

FDB
604
400

FDB
606
600

FDB
608
800

FDB
610
1000
VOLTS

IO

IFSM

90

VFM

1.3

VOLTS

IRM

10
1

A
mA

@ TA = 25 C
@ TA = 100 o C

Maximum Reverse Recovery Time (Note 1)

FDB
601
100

UNITS

TRR

200

AMPS

300

500

nS

60

AMPS2
SEC

RJC

C/W

TJ, TSTG

-55 to +150

I2t

3.0106fdb

G9

DIOTEC ELECTRONICS CORP.

Data Sheet No. FRDB-2500-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

SERIES FDB2500 - FDB2510

PRV Ratings from 50 to 1000 Volts

Surge overload rating to 300 Amps peak

BH

AC

BH

AC

Reliable low cost molded plastic construction

LT

LL

Ideal for printed circuit board applications

HOLE FOR
#8 SCREW

D1

Fast switching for high efficiency

+

LD

AC

UL RECOGNIZED - FILE #E141956

AC

D1

AC

MECHANICAL DATA

D3

BL D1

BL

D2

Case: Metal (Potting epoxy carries U/L Flammability Rating 94V-0)

D2

AC

D1
BL

BL

Terminals: Round silver plated copper pins or fast-on terminals

Soldering: Per MIL-STD 202 Method 208 guaranteed
Polarity: Marked on side of case
Mounting Position: Any. Through hole for #8 screw.
Max. mounting torque = 20 in-lb.

Suffix "T" indicates FAST-ON TERMINALS

Weight: Fast-on Terminals - 1.1 Ounces (31.6 Grams)

Wire Leads - 0.95 Ounces (28.5 Grams)

Suffix "W" indicates WIRE LEADS

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Maximum DC Blocking Voltage

VRM

FDB
2500
50

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Series Number

Average Forward Rectified Current @ TC = 55 C

Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage (Per Bridge Elemnt) at 12.5 Amps DC
Maximum Average DC Reverse Current at Rated
DC Blocking Voltage (Per Bridge Element-Note 2)

Thermal Energy (Rating for Fusing, t < 8.3 mS)

Typical Thermal Resistance, Junction to Case (Note 2)
Junction Operating and StorageTemperature Range
o

FDB
2502
200

FDB
2504
400

FDB
2506
600

FDB
2508
800

FDB
2510
1000
VOLTS

IO

25

IFSM

300

VFM

1.3

VOLTS

IRM

10
1

A
mA

@ TA = 25 C
@ TA = 100 o C

Maximum Reverse Recovery Time (Note 1)

FDB
2501
100

UNITS

TRR

200

AMPS

300

500

nS

373

AMPS2
SEC

RJC

1.6

C/W

TJ, TSTG

-55 to +150

I2t

NOTES: (1) TJ=25 C, IF=0.5A, IR=1A, IRR=0.25A

(2) Bridge mounted on an 5" x 6" x 4.9" thick (12.7cm x 15.2cm x 12.4cm) finned aluminum plate

3.0125fdbm

G11

DIOTEC ELECTRONICS CORP.

Data Sheet No. FRDB-2500P-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

SERIES FDB2500P - FDB2510P

PRV Ratings from 50 to 1000 Volts

Suffix "P" indicates molded PLASTIC with intergrally mounted Heat Sink

Surge overload rating to 300 Amps peak

Heat Sink
BH

BH

Reliable low cost molded plastic construction

LT

Ideal for printed circuit board applications

Fast switching for high efficiency

LL

Top View of
HeatSink

HOLE FOR
#8 SCREW

D1

UL RECOGNIZED - FILE #E141956

HOLE FOR
#8 SCREW

LD

AC

D1

MECHANICAL DATA

D3 BL

BL D1

AC

D2
_

Case: Molded plastic, U/L Flammability Rating 94V-0

D2

D1
BL

BL

Terminals: Round silver plated copper pins or fast-on terminals

Soldering: Per MIL-STD 202 Method 208 guaranteed
Polarity: Marked on side of case
Mounting Position: Any. Through hole for #8 screw.
Max. mounting torque = 20 in-lb.
Weight: Fast-on Terminals - 0.7 Ounces (20.0 Grams)
Wire Leads - 0.55 Ounces (16.0 Grams)

Suffix "T" indicates FAST-ON TERMINALS

Suffix "W" indicates WIRE LEADS

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

SYMBOL

RATINGS

Maximum DC Blocking Voltage

VRM

FDB FDB FDB FDB FDB FDB FDB

2500P 2501P 2502P 2504P 2506P 2508P 2510P
50
100
200
400
600
800
1000

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

VRRM

50

100

200

400

600

800

1000

Series Number

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ TC = 55 C

Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage (Per Bridge Element) at 12.5 Amps DC
Maximum Average DC Reverse Current at Rated
DC Blocking Voltage (Per bridge Element-Note 2)
Maximum Reverse Recovery Time (Note 1)
Thermal Energy (Rating for Fusing, t < 8.3 mS)
Typical Thermal Resistance, Junction to Case (Note 2)
Junction Operating and Storge Temperature Range
o

VOLTS

IO

25

IFSM

300

VFM

1.3

VOLTS

IRM

10
1

A
mA

@ TA = 25 C
@ TA = 100 o C

UNITS

TRR

200

AMPS

300

500

nS

373

AMPS2
SEC

RJC

1.2

C/W

TJ, TSTG

-55 to +150

It

NOTES: (1) TJ=25 C, IF=0.5A, IR=1A, IRR=0.25A

(2) Bridge mounted on an 5" x 6" x 4.9" thick (12.7cm x 15.2cm x 12.4cm) finned aluminum plate

3.0125dbp

G13

DIOTEC ELECTRONICS CORP.

Data Sheet No. FRDB-3500-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

SERIES FDB3500 - FDB3510

PRV Ratings from 50 to 1000 Volts

Surge overload rating to 400 Amps peak

AC

BH

BH

AC

Reliable low cost molded plastic construction

LT

LL

Ideal for printed circuit board applications

HOLE FOR
#8 SCREW

D1

Fast switching for high efficiency

+

LD

AC

UL RECOGNIZED - FILE #E124962

AC

D1

AC

MECHANICAL DATA

D3

BL D1

BL

D2

Case: Metal (Potting epoxy carries U/L Flammability Rating 94V-0)

D2

AC

D1
BL

BL

Terminals: Round silver plated copper pins or fast-on terminals

Soldering: Per MIL-STD 202 Method 208 guaranteed
Polarity: Marked on side of case
Mounting Position: Any. Through hole for #8 screw.
Max. mounting torque = 20 in-lb.

Suffix "T" indicates FAST-ON TERMINALS

Weight: Fast-on Terminals - 1.1 Ounces (31.6 Grams)

Wire Leads - 0.95 Ounces (28.5 Grams)

Suffix "W" indicates WIRE LEADS

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Maximum DC Blocking Voltage

VRM

FDB
3500
50

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Series Number

Average Forward Rectified Current @ TC = 55 C

Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage (Per Bridge Element) at 17.5 Amps DC
Maximum Average DC Reverse Current at Rated
DC Blocking Voltage (Per Bridge Element-Note 2)

Thermal Energy (Rating for Fusing, t < 8.3 mS)

Typical Thermal Resistance, Junction to Case (Note 2)
Junction Operating and Staorage Temperature Range
o

FDB
3502
200

FDB
3504
400

FDB
3506
600

FDB
3508
800

FDB
3510
1000
VOLTS

IO

35

IFSM

400

VFM

1.3

VOLTS

IRM

10
1

A
mA

@ TA = 25 C
@ TA = 100 o C

Maximum Reverse Recovery Time (Note 1)

FDB
3501
100

UNITS

TRR

200

AMPS

300

500

nS

664

AMPS2
SEC

RJC

1.6

C/W

TJ, TSTG

-55 to +150

I2t

NOTES: (1) TJ=25 C, IF=0.5A, IR=1A, IRR=0.25A

(2) Bridge mounted on an 9" x 3" x 4.6" thick (22.9cm x 7.6cm x 11.7cm) finned aluminum plate

3.0135fdbm

G15

DIOTEC ELECTRONICS CORP.

Data Sheet No. FRDB-3500P-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

SERIES FDB3500P - FDB3510P

PRV Ratings from 50 to 1000 Volts

Suffix "P" indicates molded PLASTIC with intergrally mounted Heat Sink

Surge overload rating to 400 Amps peak

Heat Sink
BH

BH

Reliable low cost molded plastic construction

LT

Ideal for printed circuit board applications

Fast switching for high efficiency

LL

Top View of
HeatSink

HOLE FOR
#8 SCREW

D1

UL RECOGNIZED - FILE #E141956

HOLE FOR
#8 SCREW

LD

AC

D1

MECHANICAL DATA

D3 BL

BL D1

AC

D2
_

Case: Molded plastic, U/L Flammability Rating 94V-0

D2

D1
BL

BL

Terminals: Round silver plated copper pins or fast-on terminals

Soldering: Per MIL-STD 202 Method 208 guaranteed
Polarity: Marked on side of case
Mounting Position: Any. Through hole for #8 screw.
Max. mounting torque = 20 in-lb.
Weight: Fast-on Terminals - 0.7 Ounces (20.0 Grams)
Wire Leads - 0.55 Ounces (16.0 Grams)

Suffix "T" indicates FAST-ON TERMINALS

Suffix "W" indicates WIRE LEADS

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

SYMBOL

RATINGS

Maximum DC Blocking Voltage

VRM

FDB FDB FDB FDB FDB FDB FDB

3500P 3501P 3502P 3504P 3506P 3508P 3510P
50
100
200
400
600
800
1000

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

VRRM

50

100

200

400

600

800

1000

Series Number

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ TC = 55 C

Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage, Per Diode, at 17.5 Amps DC
Maximum Average DC Reverse Current at Rated
DC Blocking Voltage Per Diode (Note 2)
Maximum Reverse Recovery Time (Note 1)
Thermal Energy (Rating for Fusing, t < 8.3 mS)
Typical Thermal Resistance, Junction to Case (Note 2)
Operating and Storge Temperature Range
o

VOLTS

IO

35

IFSM

400

VFM

1.3

VOLTS

IRM

10
1

A
mA

@ TA = 25 C
@ TA = 100 o C

UNITS

TRR

200

AMPS

300

500

nS

664

AMPS2
SEC

RJC

1.2

C/W

TJ, TSTG

-55 to +150

It

NOTES: (1) TJ=25 C, IF=0.5A, IR=1A, IRR=0.25A

(2) Bridge mounted on an 9" x 3" x 4.6" thick (22.9cm x 7.6cm x 11.7cm) finned aluminum plate

3.0135fdbp

G17

SECTION H
GENERAL PURPOSE
AND
FAST RECOVERY DIODES

GENERAL PURPOSE DIODES

1-6 AMPERES
50 to 1000 VOLTS

DO - 41

DO - 27

ULTRA FAST SWITCHING DIODES

0.150 AMPERES
75 VOLTS
DO - 35

FAST RECOVERY SILICON DIODES

1-8 AMPERES
50 to 1000 VOLTS
DO - 41

DO - 27

G-6A

TO-220AC

DIOTEC ELECTRONICS CORP. - 18020 Hobart Blvd., Unit B - Gardena, CA 90248 U.S.A. - PH: 310-767-1052 - FX: 310-767-7958

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPDP-101-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-41 PACKAGE

Low cost

SERIES 1N4001 - 1N4007

DO - 41

Low leakage

LL

Low forward voltage drop

BD (Dia)

High current capacity

BL

Easily cleaned with freon, alcohol, chlorothene and similar

solvents

Color Band
Denotes
Cathode

MECHANICAL DATA
LL
Case: JEDEC DO-41, molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym

Polarity: Color band denotes cathode

BL
Mounting Position: Any

BD

Weight: 0.012 Ounces (0.34 Grams)

LL
LD

Maximum
In
mm

4.1

0.205

5.2

0.103

2.6

0.107

2.7

1.00
0.028

25.4
0.71

0.034

0.86

0.160

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

1N4001 1N4002 1N4003 1N4004 1N4005 1N4006 1N4007

Maximum DC Blocking Voltage

VRM

50

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM

Average Forward Rectified Current @ TA = 75 oC

(Lead length = 0.375 in. (9.5 mm))
Peak Forward Surge Current (8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 1 Amp DC
Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1)
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

@ TA = 25oC
o
@ TA = 100 C

Typical Thermal Resistance, Junction to Ambient (Note 1)

Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range
NOTES: (1) Lead length = 0.375 in. (9.5 mm)
(2) Measured at 1MHz & applied reverse voltage of 4 volts

UNITS

1000

100

200

400

600

800

35

70

140

280

420

560

700

50

100

200

400

600

800

1000

IO

IFSM

50

VFM

IRM(AV)

30

IRM

5
50

RJA

30

VOLTS

AMPS

VOLTS
A
C/W

CJ

26

pF

TJ, TSTG

-65 to +175

C
4.97fgpdp101

H1

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPDP-101-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1 AMP GENERAL PURPOSE SILICON DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES 1N4001 - 1N4007
50

40

30
Single Phase, Half wave, 60 Hz
Resistive and Inductive Loads
Lead Length = 0.375" (9.5 mm)

20
JEDEC Method
8.3 mS Half Sine Wave

10

Ambient Temperature, o C

0
10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
10

10

TJ = 100 oC

1.0

1.0

0.1

0.1

TJ = 25 oC

TJ = 25 oC
Pulse Width = 300 S
1% Duty Cycle

.01

20

0.01

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

100

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

1000
o

TJ = 25 C

T J = 25 oC

10

100

TJ = 25 oC
Non-repetitive Square Pulse
di/dt =200 S
0.1
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

H2

10
0.01

0.1

1.0

10

Pulse Duration (Milliseconds)

FIGURE 6. PEAK FORWARD SURGE CURRENT

4.97bgpdp101

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPPD-100-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

ACTUAL SIZE OF
DO-41 PACKAGE

SERIES 1N4001G - 1N4007G

DO - 41

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES

LOW FORWARD VOLTAGE DROP

BL
Color Band
Denotes
Cathode

1A at TA = 75 oC WITH NO THERMAL RUNAWAY

MECHANICAL DATA

LL
Case: JEDEC DO-41, molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym

Polarity: Color band denotes cathode

BD

Weight: 0.012 Ounces (0.34 Grams)

LL
LD

4.1

0.205

5.2

0.103

2.6

0.107

2.7

1.00
0.028

25.4
0.71

0.034

0.86

0.160

BL
Mounting Position: Any

Maximum
In
mm

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

1N
1N
1N
1N
1N
1N
1N
4001G 4002G 4003G 4004G 4005G 4006G 4007G

Series Number
Maximum DC Blocking Voltage

VRM

50

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM

Average Forward Rectified Current @ TA = 75 oC

(Lead length = 0.375 in. (9.5 mm))
Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 1 Amp DC
Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1)
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

@ TA = 25oC
o
@ TA = 100 C

Typical Thermal Resistance, Junction to Ambient (Note 1)

Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range
NOTES: (1) Lead length = 0.375 in. (9.5 mm)
(2) Measured at 1MHz & applied reverse voltage of 4 volts

UNITS

1000

100

200

400

600

800

35

70

140

280

420

560

700

50

100

200

400

600

800

1000

IO

IFSM

50

VFM

IRM(AV)

10

IRM

1
20

RJA

30

VOLTS

AMPS

VOLTS
A
C/W

CJ

10

pF

TJ, TSTG

-65 to +175

C
4.97fgppd100

H3

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPPD-100-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1 AMP SOFT GLASS PASSIVATED SILICON DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES 1N4001G - 1N4007G
50

40

30
Single Phase, Half wave, 60 Hz
Resistive and Inductive Loads
Lead Length = 0.375" (9.5 mm)

20
JEDEC Method
8.3 mS Half Sine Wave

10

Ambient Temperature, o C

0
1

FIGURE 1. FORWARD CURRENT DERATING CURVE

10

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
10
10
TJ = 100 oC

1.0

1.0

0.1
TJ = 25 oC

0.1
TJ = 25 oC
Pulse Width = 300 S
1% Duty Cycle
.01

20

0.01

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

100

1000
o

TJ = 25 C

T J = 25 oC

10

100

TJ = 25 oC
Non-repetitive Square Pulse
di/dt =200 S
0.1
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

H4

10
0.01

0.1

1.0

10

Pulse Duration (Milliseconds)

FIGURE 6. PEAK FORWARD SURGE CURRENT

4.97bgppd100

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPDG-101-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

ACTUAL SIZE OF
DO-41 PACKAGE

SERIES GP100 - GP110

DO - 41

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES

LOW FORWARD VOLTAGE DROP

BL
Color Band
Denotes
Cathode

1A at TA = 75 oC WITH NO THERMAL RUNAWAY

MECHANICAL DATA

LL
Case: JEDEC DO-41, molded silica glass
(U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym

Polarity: Color band denotes cathode

BD

Weight: 0.012 Ounces (0.34 Grams)

LL
LD

4.1

0.205

5.2

0.103

2.6

0.107

2.7

1.00
0.028

25.4
0.71

0.034

0.86

0.160

BL
Mounting Position: Any

Maximum
In
mm

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

GP100 GP101 GP102 GP104 GP106 GP108 GP110

Series Number
Maximum DC Blocking Voltage

VRM

50

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM

Average Forward Rectified Current @ TA = 75 oC,

Lead length = 0.375 in. (9.5 mm)
Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 1 Amp DC
Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1)
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

@ TA = 25oC
o
@ TA = 125 C

Typical Thermal Resistance, Junction to Ambient (Note 1)

Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range
NOTES: (1) Lead length = 0.375 in. (9.5 mm)
(2) Measured at 1MHz & applied reverse voltage of 4 volts

UNITS

1000

100

200

400

600

800

35

70

140

280

420

560

700

50

100

200

400

600

800

1000

IO

IFSM

50

VFM

VOLTS

AMPS

IRM(AV)

IRM

0.5
30.0

RJA

30

VOLTS
A
C/W

CJ

10

pF

TJ, TSTG

-65 to +175

C
4.97fgpdg101

H5

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPDG-101-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1 AMP HIGH RELIABILITY SILICON DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES GP100 - GP110
50

40

30
Single Phase, Half wave, 60 Hz
Resistive and Inductive Loads
Lead Length = 0.375" (9.5 mm)

20
JEDEC Method
8.3 mS Half Sine Wave

10

Ambient Temperature, o C

0
10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
10
10

TJ = 100 oC

1.0

1.0

0.1
TJ = 25 oC

0.1
TJ = 25 oC
Pulse Width = 300 S
1% Duty Cycle
.01

20

60

80

100

120

140

0.01

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

100

1000
o

TJ = 25 C

T J = 25 oC

10

100

TJ = 25 oC
Non-repetitive Square Pulse
di/dt =200 S
0.1
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

H6

10
0.01

0.1

1.0

10

Pulse Duration (Milliseconds)

FIGURE 6. PEAK FORWARD SURGE CURRENT

4.97bgpdg101

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPSM-100-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
Low profile package - designed for surface mount applications

SERIES S1A - S1M

Built-in strain relief, ideal for automated placement

Glass passivated chip junction

0.115 (2.93)
0.109 (2.77)

0.083 (2.10)
0.068 (1.72)

High temperature soldering: 250 C/10 seconds at terminals

0.182 (4.63)
0.176 (4.48)

MECHANICAL DATA

Case: Molded epoxy, U/L Flammability Rating 94V-0

Terminals: Solder plated

0.112 (3.10)
0.118 (2.85)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Polarity: Color band identifies cathode terminal

0.055 (1.40)
0.039 (1.00)

0.018 (0.45) Max.

Weight: 0.004 Ounces (0.115 Grams)

0.226 (5.74)
0.218 (5.48)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number
Maximum Recurrent Peak Reverse Voltage

VRRM

Maximum RMS Voltage

UNITS

S1A

S1B

S1D

S1G

S1J

S1K

S1M

50

100

200

400

600

800

1000

VRMS

35

70

140

280

420

560

700

Maximum DC Blocking Voltage

VDC

50

100

200

400

600

800

1000

Maximum Average Forward Rectified Current @ TL = 110 oC

I(AV)

1.0

Peak Forward Surge Current (8.3mS single half sine wave

superimposed on rated load- JEDEC Method) TL = 110 OC

IFSM

40.0

VFM

1.10

VOLTS

IRM

1.0
50.0

TRR

1.8

CJ

12.0

pF

RJL
R JA
TJ ,TSTG

27.0
75.0
-55 to +150

Maximum Instantaneous Forward Voltage at 1.0 Amp DC

Maximum DC Reverse Current At Rated DC
Blocking Voltage
Typical Reverse Recovery Time (Note 1)
Typical Junction Capacitance (Note 2)
Typical Thermal Resistance (Note 3)
Operating and Storage Temperature Range

@ TA = 25 C
@ TA = 125 oC

VOLTS

AMPS

C/W
C
3.0101s1a

NOTES: (1) Reverse Recovery Test Conditions: I F= 0.5A, I R = 1.0A, I RR = 0.25A

(2) Measured at 1.0 MHz and Applied Reverse Voltage of 4.0 Volts
(3) Thermal Resistance From Junction to Ambient and Junction to Lead Mounted on 0.2" x 0.2" ( 5.0mm x 5.0mm) Copper Pad A reas

H7

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPSM-100-2A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1 AMP SURFACE MOUNT RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES S1A - S1M
100

10

TL = 110 OC
8.3mS Single Half Sine Wave
(JEDEC Method)

0.2" x 0.2" (5.0mm x 5.0mm)

Thick Copper Pad Areas)

Lead Temperature, oC

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT

100

100

10
10

1.0
1.0

0.1

0.1
0.01

Pulse Width = 300 S

1% Duty Cycle

0.001

0.01

Instantaneous Forward Voltage, VF (Volts)

FIGURE 3. TYPICAL INSTANTANEOUS FORWARD CHARACTERISTIC

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage, %

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

TJ = 25 OC
f = 1.0 MHz
Vsig = 50 mVP-P

Reverse Voltage, VR (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

H8

Units Mounted on
0.20" x 0.20" (5.0mm x 5.0mm)
Copper Pad Areas;
0.0005" (0.013mm) Thick

Pulse Duration, t (Sec)

FIGURE 6. TRANSIENT THERMAL IMPEDANCE

3.0101s1a

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPDP-151-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-15 PACKAGE

Low cost

SERIES 1N5391 - 1N5399

DO - 15

Low leakage

LL

Low forward voltage drop

BD (Dia)

High current capacity

BL

Easily cleaned with freon, alcohol, chlorothene and similar

solvents

Color Band
Denotes
Cathode

MECHANICAL DATA
LL
Case: JEDEC DO-15 molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym

Polarity: Color band denotes cathode

BL
Mounting Position: Any

BD

Weight: 0.01 Ounces (0.4 Grams)

LL
LD

Maximum
In
mm

6.01

0.255

6.48

0.130

3.3

0.140

3.6

1.00
0.028

25.4
0.71

0.034

0.86

0.240

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

1N5391 1N5392 1N5393 1N5395 1N5397 1N5398 1N5399

Maximum DC Blocking Voltage

VRM

50

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM

Average Forward Rectified Current @ TA = 75 oC,

Lead length = 0.375 in. (9.5 mm)
Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 1.5 Amps DC
Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1)
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

@ TA = 25oC
o
@ TA = 100 C

Typical Thermal Resistance, Junction to Ambient (Note 1)

Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range
NOTES: (1) Lead length = 0.375 in. (9.5 mm)
(2) Measured at 1MHz & applied reverse voltage of 4 volts

UNITS

1000

100

200

400

600

800

35

70

140

280

420

560

700

50

100

200

400

600

800

1000

IO

1.5

IFSM

60

VFM

IRM(AV)

30

IRM

5
50

RJA

50

VOLTS

AMPS

VOLTS
A
C/W

CJ

30

pF

TJ, TSTG

-65 to +175

C
4.97fgpdp151

H9

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPDP-151-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1.5 AMP GENERAL PURPOSE SILICON DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES 1N5391 - 1N5399
75

60

45

30

15

Ambient Temperature, o C

0
10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10
10

TJ = 100 oC

1.0

1.0

0.1

0.1
TJ = 25 oC

.01

0.01

Instantaneous Forward Voltage (Volts)

20

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

100
TJ = 25 oC

10

0.1
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

H10

4.97bgpdp151

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPPD-200-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

ACTUAL SIZE OF
DO-41 PACKAGE

SERIES GP200 - GP210

DO - 41

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES

LOW FORWARD VOLTAGE DROP

BL
Color Band
Denotes
Cathode

1A at TA = 75 oC WITH NO THERMAL RUNAWAY

MECHANICAL DATA

LL
Case: JEDEC DO-41 molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Polarity: Color band denotes cathode

Minimum
In
mm

Sym

0.160

BL

Mounting Position: Any

Weight: 0.01 Ounces (0.4 Grams)

Maximum
In
mm

4.1

0.205

5.2

BD

0.103

2.6

0.107

2.7

LL
LD

1.00
0.028

25.4
0.71

0.034

0.86

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

UNITS

GP200 GP201 GP202 GP204 GP206 GP208 GP210

Series Number
Maximum DC Blocking Voltage

VRM

50

100

200

400

600

800

1000

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Average Forward Rectified Current @ TA = 75 oC,

Lead length = 0.375 in. (9.5 mm)
Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)

IO

IFSM

70

Maximum Forward Voltage at 2 Amps DC

VFM

1.1

Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)

TRR

30

IRM

5
50

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage
Typical Junction Capacitance (Note 1)
Operating and Storage Temperature Range
NOTES: (1) Measured at 1MHz & applied reverse voltage of 4 volts
(2) 300 nS available - consult factory

@ TA = 25oC
@ TA = 100oC

VOLTS

AMPS

VOLTS
A

CJ

40

pF

TJ, TSTG

-65 to +175

C
4.97 fgppd200

H11

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPPD-200-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

2 AMP SOFT GLASS PASSIVATED SILICON DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES GP200 - GP210
100

80

60

40

20

Ambient Temperature, o C

0
10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

10

10

TJ = 100 oC

1.0

1.0

0.1

0.1

TJ = 25 oC

.01

0.01

Instantaneous Forward Voltage (Volts)

20

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

100
TJ = 25 oC

10

0.1
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

H12

4.97bgpdp2

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPDP-301-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-27 PACKAGE

Low cost

SERIES 1N5400 - IN5408

DO - 27

Low leakage

LL

Low forward voltage drop

BD (Dia)

High current capacity

BL

Easily cleaned with freon, alcohol, chlorothene and similar

solvents

Color Band
Denotes
Cathode

MECHANICAL DATA
LL
Case: JEDEC DO-27 molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Sym
Polarity: Color band denotes cathode

Minimum
In
mm

Maximum
In
mm

BL

0.365

9.28

Mounting Position: Any

BD

0.205

5.2

Weight: 0.02 Ounces (0.7 Grams)

LL
LD

0.052

1.3

1.00
0.048

25.4
1.2

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

1N5400 1N5401 1N5402 1N5404 1N5406 1N5407 1N5408

Maximum DC Blocking Voltage

VRM

50

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM

Average Forward Rectified Current @ TA = 75 oC

Lead length = 0.375 in. (9.5 mm)
Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 3 Amps DC
Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1)
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

@ TA = 25oC
o
@ TA = 100 C

Typical Thermal Resistance, Junction to Ambient (Note 1)

Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range
NOTES: (1) Lead length = 0.375 in. (9.5 mm)
(2) Measured at 1MHz & applied reverse voltage of 4 volts

UNITS

1000

100

200

400

600

800

35

70

140

280

420

560

700

50

100

200

400

600

800

1000

IO

IFSM

200

VFM

IRM(AV)

30

IRM

5
50

RJA

18

VOLTS

AMPS

VOLTS
A
C/W

CJ

70

pF

TJ, TSTG

-65 to +175

C
4.97fgpdp301

H13

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPDP-301-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

3 AMP GENERAL PURPOSE SILICON DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES 1N5400 - 1N5408

RESISTIVE OR INDUCTIVE LOADS

1000

Maximum Non-repetitive

100
o

TJ = 25 C

NOTE 1
Maximum Repetitive

10
1

10

Ambient Temperature, C

100

Number of Cycles at 60Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. FORWARD SURGE CURRENT

100
10

10
1.0

1.0
0.1
TJ = 25 oC

0.1
.01

20

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

0.01

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

100
TJ = 25 oC

NOTES
(1) Single Phase, Half Wave, 60 Hz; Lead Length = 0.375" (9.5mm)
(2) TJ = 25 oC, Pulse Width = 300 Sec, 1.0% Duty Cycle

10

0.1
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

H14

4.97bgpdp301

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPPD-300-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

ACTUAL SIZE OF
DO-27 PACKAGE

SERIES 1N5400G - IN5408G

DO - 27

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES

LOW FORWARD VOLTAGE DROP

BL
Color Band
Denotes
Cathode

3A at TA = 75 oC WITH NO THERMAL RUNAWAY

MECHANICAL DATA

LL
Case: JEDEC DO-27 molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym
Polarity: Color band denotes cathode

Maximum
In
mm

BL

0.365

9.28

Mounting Position: Any

BD

0.205

5.2

Weight: 0.02 Ounces (0.7 Grams)

LL
LD

0.052

1.3

1.00
0.048

25.4
1.2

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

1N
1N
1N
1N
1N
1N
1N
5400G 5401G 5402G 5404G 5406G 5407G 5408G

Series Number
Maximum DC Blocking Voltage

VRM

50

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM

Average Forward Rectified Current @ TA = 75 oC

(Lead length = 0.375 in. (9.5 mm))
Peak Forward Surge Current (8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 3 Amps DC
Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1)
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

@ TA = 25oC
o
@ TA = 100 C

Typical Thermal Resistance, Junction to Ambient (Note 1)

Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range
NOTES: (1) Lead length = 0.375 in. (9.5 mm)
(2) Measured at 1MHz & applied reverse voltage of 4 volts

UNITS

1000

100

200

400

600

800

35

70

140

280

420

560

700

50

100

200

400

600

800

1000

IO

IFSM

200

VFM

IRM(AV)

20

IRM

2
50

RJA

18

VOLTS

AMPS

VOLTS
A
C/W

CJ

70

pF

TJ, TSTG

-65 to +175

C
4.97fgppd300

H15

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPPD-300-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

3 AMP SOFT GLASS PASSIVATED SILICON DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES 1N5400G - 1N5408G

RESISTIVE OR INDUCTIVE LOADS

1000

Maximum Non-repetitive

100
o

TJ = 25 C

NOTE 1
Maximum Repetitive

10
1

10

100

Ambient Temperature, C

Number of Cycles at 60Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. FORWARD SURGE CURRENT

100
10

10
1.0

1.0
0.1
TJ = 25 oC

0.1
.01

20

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

0.01

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

100
TJ = 25 oC

NOTES
(1) Single Phase, Half Wave, 60 Hz; Lead Length = 0.375" (9.5mm)
(2) TJ = 25 oC, Pulse Width = 300 Sec, 1.0% Duty Cycle

10

0.1
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

H16

4.97bgppd300

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPPD-400-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

ACTUAL SIZE OF
DO-27 PACKAGE

SERIES GP400 - GP410

DO - 27

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES

LOW FORWARD VOLTAGE DROP

BL
Color Band
Denotes
Cathode

4A at TA = 75 oC WITH NO THERMAL RUNAWAY

MECHANICAL DATA

LL
Case: JEDEC DO-27 molded silica glass
(U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym
Polarity: Color band denotes cathode

Maximum
In
mm

BL

0.365

9.28

Mounting Position: Any

BD

0.205

5.2

Weight: 0.02 Ounces (0.7 Grams)

LL
LD

0.052

1.3

1.00
0.048

25.4
1.2

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

GP400 GP401 GP402 GP404 GP406 GP408 GP410

Series Number
Maximum DC Blocking Voltage

VRM

50

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM

Average Forward Rectified Current @ TA = 75 oC,

Lead length = 0.375 in. (9.5 mm)
Peak Forward Surge Current (8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 4 Amps DC
Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1)
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

@ TA = 25oC
o
@ TA = 100 C

Typical Thermal Resistance, Junction to Ambient (Note 1)

Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range
NOTES: (1) Lead length = 0.375 in. (9.5 mm)
(2) Measured at 1MHz & applied reverse voltage of 4 volts

UNITS

1000

100

200

400

600

800

35

70

140

280

420

560

700

50

100

200

400

600

800

1000

IO

IFSM

200

VFM

IRM(AV)

20

IRM

2
50

RJA

18

VOLTS

AMPS

VOLTS
A
C/W

CJ

70

pF

TJ, TSTG

-65 to +175

C
4.97fgppd400

H17

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPPD-400-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

4 AMP HIGH RELIABILITY SOFT GLASS PASSIVATED SILICON DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES GP400 - GP410

RESISTIVE OR INDUCTIVE LOADS

1000

Maximum Non-repetitive

100
o

TJ = 25 C

NOTE 1
Maximum Repetitive

10
1

10

100

Number of Cycles at 60Hz

Ambient Temperature, C
FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. FORWARD SURGE CURRENT

100
10

10
1.0

1.0
0.1
o

TJ = 25 C

0.1
.01

20

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

0.01

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

100
TJ = 25 oC

NOTES
(1) Single Phase, Half Wave, 60 Hz; Lead Length = 0.375" (9.5mm)
(2) TJ = 25 oC, Pulse Width = 300 Sec, 1.0% Duty Cycle

10

0.1
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

H18

4.97bgpdp400

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPDP-601-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
GP600 PACKAGE

Low cost

SERIES GP600 - GP610

Low leakage

LL

Low forward voltage drop

BD (Dia)

High current capacity

BL

Color Band
Denotes
Cathode

Easily cleaned with freon, alcohol, chlorothene and similar

solvents

MECHANICAL DATA

LL

Case: Molded epoxy (U/L Flammability Rating 94V-0)

LD (Dia)

Terminals: Plated axial leads

Soldering: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym
Polarity: Color band denotes cathode

Maximum
In
mm

8.6

0.360

9.1

0.340

8.6

0.360

9.1

1.00
0.048

25.4
1.2

0.052

1.3

BL

0.340

Mounting Position: Any

BD

Weight: 0.07 Ounces (2.1 Grams)

LL
LD

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

GP600 GP601 GP602 GP604 GP606 GP608 GP610

Maximum DC Blocking Voltage

VRM

50

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM

Average Forward Rectified Current @ TA = 60 oC,

Lead length = 0.375 in. (9.5 mm)
Peak Forward Surge Current (8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 6 Amps DC
Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1)
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

@ TA = 25oC
o
@ TA = 100 C

Typical Thermal Resistance, Junction to Ambient (Note 1)

Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range
NOTES: (1) Lead length = 0.375 in. (9.5 mm)
(2) Measured at 1MHz & applied reverse voltage of 4 volts

UNITS

1000

100

200

400

600

800

35

70

140

280

420

560

700

50

100

200

400

600

800

1000

IO

IFSM

400

VFM

IRM(AV)

25

IRM

10
100

RJA

10

VOLTS

AMPS

VOLTS
A
C/W

CJ

100

pF

TJ, TSTG

-65 to +175

C
01.00 fgpdp601

H19

DIOTEC ELECTRONICS CORP.

Data Sheet No. GPDP-601-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

6 AMP GENERAL PURPOSE SILICON DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES GP600 - GP610
500
RESISTIVE OR INDUCTIVE LOADS
400

300
Standard PC Board Mounting
(Recommended Method)
200
Ground Plane
PC Board With
1" x 1" Copper
Surface Area

TJ = 25 oC
100

NOTE 1

Ambient Temperature, o C

10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

1000
100

100
10
TJ = 100 oC

10

1.0

0.1

1.0

TJ = 25 oC

0.01
20

60

80

100

120

140

0.1

Percent of Rated Peak Reverse Voltage

Instantaneous Forward Voltage (Volts)
FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

20

15

NOTES
(1) Single Phase, Half Wave, 60 Hz

10

(2) TJ = 25 oC, Pulse Width = 300 Sec, 1.0% Duty Cycle

L

5
Both Leads of Equal Length, L
0

0.5

1.0

Lead Length toHeat Sink, L (Inches)

FIGURE 5. TYPICAL THERMAL RESISTANCE

H20

4.97bgpdp601

DIOTEC ELECTRONICS CORP.

Data Sheet No. UFSD-101-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

1N4148

ACTUAL SIZE OF
DO-35 PACKAGE

Hermetically sealed glass package

DO-35

Low cost
Super fast recovery time

LL
BD (Dia)

Low leakage
Low forward voltage drop
BL
Color Band
Denotes
Cathode

High current capability

MECHANICAL DATA
LL
Case: JEDEC DO-35 molded glass (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym
Polarity: Color band denotes cathode

Maximum
In
mm

3.6

0.150

3.81

0.07

1.78

0.072

1.83

1.00
0.02

25.4
0.52

0.03

0.8

BL

0.142

Mounting Position: Any

BD

Weight: 0.005 Ounces (0.14 Grams)

LL
LD

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

SYMBOL

Series Number

UNITS

1N4148

Breakdown Voltage at IR = 5 A
Breakdown Voltage at IR = 100 A
Maximum Peak Recurrent Reverse Voltage
Average Forward Rectified Current @ TA = 50 oC,
Lead length = 0.375 in. (9.5 mm)
Pulse Width = 1 Sec
Peak Forward Surge Current
Pulse Width = 1 Sec
Maximum Forward Voltage at 10 mA DC
Maximum Power Dissipation
Maximum Average DC Reverse Current

RATINGS

@ VR = 20V, TA = 25oC
@ VR = 75V, TA = 150oC

Maximum Reverse Recovery Time (Note 1)

Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range
NOTES: (1) Measured at IR = 10 mA, VR = 6V, RL = 100; recover to 1 mA
(2) Measured at 1MHz & applied reverse voltage of 0 volts DC

VB

75

VB

100

VRRM

75

IO

150

mA

IFSM

1
4

AMPS

VFM

VOLTS

PFM

500

mW

IRM

25
5

nA
A

TRR

nS

CJ

pF

TJ, TSTG

-65 to +175

VOLTS

C
4.97fufsd101

H21

DIOTEC ELECTRONICS CORP.

Data Sheet No. UFSD-100-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1N4148 MINIATURE ULTRA FAST SWITCHING DIODE

RATING & CHARACTERISTIC CURVES FOR THE 1N4148

Reverse Voltage, Volts

FIGURE 2. TYPICAL JUNCTION CAPACITANCE

Case Temperature, oC
FIGURE 1. FORWARD CURRENT DERATING CURVE

100

1.0
10

0.1
TJ = 25 oC

1.0

(1) TA = 175 C
(2) TA = 125 oC
(3) TA = 75 oC
1

0.1

0.01

(4) TA = 50 oC
(5) TA = 25 oC
.001

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS
0.01

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE

H22

4.97bufsd100

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSDP-101-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-41 PACKAGE

Low cost

SERIES 1N4933 - 1N4937

DO - 41

Low leakage

LL
Low forward voltage drop

BD (Dia)

High current capacity

BL

Fast switching for high efficiency

Color Band
Denotes
Cathode

MECHANICAL DATA
LL
Case: JEDEC DO-41, molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Sym

Polarity: Color band denotes cathode

BL
Mounting Position: Any

BD

Weight: 0.012 Ounces (0.34 Grams)

LL
LD

Minimum
In
mm

Maximum
In
mm

4.1

0.205

5.2

0.103

2.6

0.107

2.7

1.00
0.028

25.4
0.71

0.034

0.86

0.160

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

1N4933

1N4934

1N4935

1N4936

1N4937

100

200

400

600

Maximum DC Blocking Voltage

VRM

50

Maximum RMS Voltage

VRMS

35

70

140

280

420

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

Average Forward Rectified Current @ TA = 75 oC,

Lead length = 0.375 in. (9.5 mm)
Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 1 Amp DC
Maximum Reverse Recovery Time (IF=1A, VR=30V - See Fig. 5)
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

@ TA = 25oC
o
@ TA = 100 C

Typical Thermal Resistance, Junction to Ambient (Note 1)

Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range

VOLTS

IO

IFSM

30

VFM

1.2

VOLTS

TRR

200

nS

IRM

5
100

RJA

41

C/W

AMPS

CJ

15

pF

TJ, TSTG

-65 to +175

NOTES: (1) Thermal resistance from junction to ambient with diode mounted on PC Board and lead lengths = 0.375 in. (9.5 mm)
(2) Measured at 1MHz & applied reverse voltage of 4 volts

4.97ffsdp1

H23

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSDP-101-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1 AMP FAST RECOVERY SILICON DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES 1N4933 - 1N4937
50

40
JEDEC Method
8.3 mS Half Sine Wave
TJ = 150 oC

30

Single Phase, Half wave, 60 Hz

Resistive and Inductive Loads

20

10

Ambient Temperature, oC

10

100

Number of Cycles at 60 Hz

FIGURE 1. FORWARD CURRENT DERATING CURVE

FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100

10

T J = 25 oC

1.0

f = 1 MHz

10

0.1
TJ = 25 oC
Pulse Width = 300 S

0.1
0.1

0.01

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE
50
noninductive

10

Reverse Voltage, (Volts)

FIGURE 4. TYPICAL JUNCTION CAPACITANCE PER DIODE

10
noninductive

TRR
0.5

D.U.T.

(+)

(-)

25 VDC
(APPROX)

0.0

PULSE
GENERATOR
(Note 2)

(-)
1
noninductive

(+)

-0.5

OSCILLOSCOPE
(Note 1)

-1.0
NOTES:
(1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF
(2) Rise time = 10nS max., source impedance = 50 ohms

H24

Set time base

for 10nS/cm

1
cm

FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC

4.97bfsdp101

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSDP-103-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-41 PACKAGE

Low cost

SERIES RP100 - RP110

DO - 41

Low leakage

LL
Low forward voltage drop

BD (Dia)

High current capacity

BL
Fast switching for high efficiency

Color Band
Denotes
Cathode

MECHANICAL DATA
LL
Case: JEDEC DO-41, molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym

Polarity: Color band denotes cathode

BL
Mounting Position: Any

BD

Weight: 0.012 Ounces (0.34 Grams)

LL
LD

Maximum
In
mm

4.1

0.205

5.2

0.103

2.6

0.107

2.7

1.00
0.028

25.4
0.71

0.034

0.86

0.160

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

RP100 RP101 RP102 RP104 RP106 RP108 RP110

Maximum DC Blocking Voltage

VRM

50

Maximum RMS Voltage

VRMS

Maximum Peak Recurrent Reverse Voltage

VRRM

Average Forward Rectified Current @ TA = 75 oC

(Lead length = 0.375 in. (9.5 mm))
Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 1 Amp DC
Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

@ TA = 25oC
o
@ TA = 100 C

Typical Thermal Resistance, Junction to Ambient (Note 1)

Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range

UNITS

1000

100

200

400

600

800

35

70

140

280

420

560

700

50

100

200

400

600

800

1000

IO

IFSM

30

VFM

1.3

VOLTS

AMPS

TRR

150

VOLTS
250

500 ( Note 3)

nS

IRM

5
50

RJA

50

C/W

CJ

15

pF

TJ, TSTG

-65 to +175

NOTES: (1) Thermal resistance junction to ambient with diode mounted on PC Board and lead lengths = 0.375 in. (9.5 mm)
(2) Measured at 1MHz & applied reverse voltage of 4 volts
(3) 300nS available - consult factory

4.97ffsdp1a

H25

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSDP-103-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1 AMP FAST RECOVERY SILICON DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES RP100 - RP110
50

40
JEDEC Method
8.3 mS Half Sine Wave
TJ = 150 oC

30

Single Phase, Half wave, 60 Hz

Resistive and Inductive Loads

20

10

Ambient Temperature, oC

10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
100

10

T J = 25 oC

1.0

f = 1 MHz

10

0.1
TJ = 25 oC
Pulse Width = 300 S
1% Duty Cycle

0.1
0.1

0.01

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC
50
noninductive

10

Reverse Voltage, (Volts)

FIGURE 4. TYPICAL JUNCTION CAPACITANCE

10
noninductive

TRR
0.5

D.U.T.

(+)

(-)

25 VDC
(APPROX)

0.0

PULSE
GENERATOR
(Note 2)

(-)
1
noninductive

(+)

-0.5

OSCILLOSCOPE
(Note 1)

-1.0
NOTES:
(1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF
(2) Rise time = 10nS max., source impedance = 50 ohms

Set time base

for 10nS/cm

1
cm

FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC

H26

4.97bfsdp103

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSPD-100-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

ACTUAL SIZE OF
DO-41 PACKAGE

SERIES RGP100 - RGP110

DO - 41

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES

LOW FORWARD VOLTAGE DROP

BL
Color Band
Denotes
Cathode

1A at TA = 75 oC WITH NO THERMAL RUNAWAY

MECHANICAL DATA

LL
Case: JEDEC DO-41, molded silica glass
(U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202E Method 208 guaranteed

Minimum
In
mm

Sym

Polarity: Color band denotes cathode

BD

Weight: 0.012 Ounces (0.34 Grams)

LL
LD

4.1

0.205

5.2

0.103

2.6

0.107

2.7

1.00
0.028

25.4
0.71

0.034

0.86

0.160

BL
Mounting Position: Any

Maximum
In
mm

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

RGP
100

RGP
101

RGP
102

RGP
104

RGP
106

RGP
108

RGP
110

100

200

400

600

800

1000

Maximum DC Blocking Voltage

VRM

50

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Average Forward Rectified Current @ TA = 75 oC,

Lead length = 0.375 in. (9.5 mm)
Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 1 Amp DC
Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage

@ TA = 25oC
o
@ TA = 100 C

Typical Thermal Resistance, Junction to Ambient (Note 1)

Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range
NOTES: (1) Lead length = 0.375 in. (9.5 mm)
(2) Measured at 1MHz & applied reverse voltage of 4 volts
(3) 300nS avaiable - consult factory

IO

IFSM

50

VFM

1.2

VOLTS

AMPS

TRR

150

VOLTS
250

500 (Note 3)

nS

IRM

0.5
25

RJA

55

C/W

CJ

15

pF

TJ, TSTG

-65 to +175

C
4.97ffspd100

H27

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSPD-100-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

1 AMP HIGH RELIABILITY FAST RECOVERY DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES RGP100 - RGP110
50
JEDEC Method
8.3 mS Half Sine Wave
TJ = 175 oC
40

30

Single Phase, Half wave, 60 Hz

Resistive and Inductive Loads
Lead Length = 0.375" (9.5 mm)

20

10

Ambient Temperature, oC

0
10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
100

10

Pulse Width = 300 S

1% Duty Cycle

TJ =150 oC

TJ = 25 oC
f = 1 MHz
VSIG = 50 mV P-P

1.0

10

0.1
TJ =25 oC

0.1
0.1

0.01

Instantaneous Forward Voltage (Volts)

10

FIGURE 4. TYPICAL JUNCTION CAPACITANCE

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC

50
noninductive

Reverse Voltage, (Volts)

10
noninductive

TRR
0.5

D.U.T.

(+)

(-)

25 VDC
(APPROX)

0.0

PULSE
GENERATOR
(Note 2)

(-)
1
noninductive

(+)

-0.5

OSCILLOSCOPE
(Note 1)

-1.0
NOTES:
(1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF
(2) Rise time = 10nS max., source impedance = 50 ohms

Set time base

for 10nS/cm

1
cm

FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC

H28

4.97bfspd100

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSPD-200-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

ACTUAL SIZE OF
DO-41 PACKAGE

SERIES RGP200 - RGP210

DO - 41

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES

LOW FORWARD VOLTAGE DROP

BL
Color Band
Denotes
Cathode

2A at TA = 75 oC WITH NO THERMAL RUNAWAY

MECHANICAL DATA

LL
Case: JEDEC DO-41 molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Polarity: Color band denotes cathode

Minimum
In
mm

Sym

0.160

BL

Mounting Position: Any

Weight: 0.01 Ounces (0.4 Grams)

Maximum
In
mm

4.1

0.205

5.2

BD

0.103

2.6

0.107

2.7

LL
LD

1.00
0.028

25.4
0.71

0.034

0.86

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

RGP
200

RGP
201

RGP
202

RGP
204

RGP
206

RGP
208

RGP
210

Maximum DC Blocking Voltage

VRM

50

100

200

400

600

800

1000

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Average Forward Rectified Current @ TA = 75 oC,

Lead length = 0.375 in. (9.5 mm)
Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)

IO

IFSM

60

AMPS

Maximum Forward Voltage at 2 Amps DC

VFM

Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)

TRR

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage
Typical Junction Capacitance (Note 1)
Operating and Storage Temperature Range
NOTES: (1) Measured at 1MHz & applied reverse voltage of 4 volts
(2) 300 nS available - consult factory

@ TA = 25oC
@ TA = 100oC

VOLTS

IRM

VOLTS

1.3
150

250
1.0
100

500 (Note 2)

nS
A

CJ

15

pF

TJ, TSTG

-65 to +175

C
4.97ffspd200

H29

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSPD-200-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

2 AMP FAST RECOVERY SILICON DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES RGP200 - RGP210
50

40

30

Single Phase, Half wave, 60 Hz

Resistive and Inductive Loads
Lead Length = 0.375" (9.5 mm)

20

JEDEC Method
8.3 mS Single
Half Sine Wave

10

Ambient Temperature, oC

10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

20

100

10

TJ = 25 oC
f = 1 MHz
VSIG = 50 mV P-P

1.0

10

0.1
TJ = 25 oC
Pulse Width = 300 S
1% Duty Cycle

0.1
0.1

0.01

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC
50
noninductive

10

Reverse Voltage, (Volts)

FIGURE 4. TYPICAL JUNCTION CAPACITANCE

10
noninductive

TRR
0.5

D.U.T.

(+)

(-)

25 VDC
(APPROX)

0.0

PULSE
GENERATOR
(Note 2)

(-)
1
noninductive

(+)

-0.5

OSCILLOSCOPE
(Note 1)

-1.0
NOTES:
(1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF
(2) Rise time = 10nS max., source impedance = 50 ohms

Set time base

for 10nS/cm

1
cm

FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC

H30

4.97bfspd200

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSDP-301-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-27 PACKAGE

Low cost

SERIES RP300 - RP310

DO - 27

Low leakage

LL
Low forward voltage drop

BD (Dia)

High current capacity

BL
Fast switching for high efficiency

Color Band
Denotes
Cathode

MECHANICAL DATA
LL
Case: JEDEC DO-27 molded plastic (U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Sym
Polarity: Color band denotes cathode
Mounting Position: Any

Maximum
In
mm

BL

0.365

9.28

BD

0.205

5.2

0.052

1.3

LL
LD

Weight: 0.02 Ounces (0.7 Grams)

Minimum
In
mm

1.00
0.048

25.4
1.2

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

RP300 RP301 RP302 RP304 RP306 RP308 RP310

Maximum DC Blocking Voltage

VRM

50

100

200

400

600

800

1000

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Average Forward Rectified Current @ TA = 55 oC,

Lead length = 0.375 in. (9.5 mm)
Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)

IO

IFSM

200

AMPS

Maximum Forward Voltage at 3 Amps DC

VFM

Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)

TRR

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage
Typical Junction Capacitance (Note 1)
Operating and Storage Temperature Range
at =1MHz
applied
reverse voltage of 4 volts
NOTES: (1) Measured
Lead length
0.375&in.
(9.5 mm)
(2) 300
nS avaiable
- consult
withreverse
factoryvoltage of 4 volts
Measured
at 1MHz
& applied

@ TA = 25oC
@ TA = 100oC

VOLTS

IRM

VOLTS

1.3
150

250
10
150

500 (Note 2)

nS
A

CJ

60

pF

TJ, TSTG

-65 to +175

C
4.97ffsdp301

H31

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSDP-301-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

3 AMP FAST RECOVERY SILICON DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES RP300 - RP310
500

JEDEC Method
8.3 mS Single
Half Sine Wave
TJ = 55 oC
100
Single Phase, Half wave, 60 Hz
Resistive and Inductive Loads
Lead Length = 0.375" (9.5 mm)

Ambient Temperature, oC

10
10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
100

10

TJ = 25 oC

1.0

f = 1 MHz
10

0.1
TJ = 25 oC
Pulse Width = 300 S
1% Duty Cycle

0.1
0.1

0.01

Instantaneous Forward Voltage (Volts)

10

FIGURE 4. TYPICAL JUNCTION CAPACITANCE

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC

50
noninductive

Reverse Voltage, (Volts)

10
noninductive

TRR
0.5

D.U.T.

(+)

(-)

25 VDC
(APPROX)

0.0

PULSE
GENERATOR
(Note 2)

(-)
1
noninductive

(+)

-0.5

OSCILLOSCOPE
(Note 1)

-1.0
NOTES:
(1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF
(2) Rise time = 10nS max., source impedance = 50 ohms

Set time base

for 10nS/cm

1
cm

FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC

H32

4.97bfsdp301

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSPD-300-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

ACTUAL SIZE OF
DO-27 PACKAGE

SERIES RGP300 - RGP310

DO - 27

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES

LOW FORWARD VOLTAGE DROP

BL
Color Band
Denotes
Cathode

3A at TA = 55 oC WITH NO THERMAL RUNAWAY

MECHANICAL DATA

LL
Case: JEDEC DO-27 molded silica glass
(U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym
Polarity: Color band denotes cathode
Mounting Position: Any

BL

0.365

9.28

BD

0.205

5.2

0.052

1.3

1.00
0.048

LL
LD

Weight: 0.02 Ounces (0.7 Grams)

Maximum
In
mm

25.4
1.2

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

RGP
300

RGP
301

RGP
302

RGP
304

RGP
306

RGP
308

RGP
310

Maximum DC Blocking Voltage

VRM

50

100

200

400

600

800

1000

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Average Forward Rectified Current @ TA = 55 oC,

Lead length = 0.375 in. (9.5 mm)
Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)

IO

IFSM

200

AMPS

Maximum Forward Voltage at 3 Amps DC

VFM

Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)

TRR

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage
Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range
NOTES: (1) Lead length = 0.375 in. (9.5 mm)
(2) Measured at 1MHz & applied reverse voltage of 4 volts
(3) 300 nS avaiable - consult with factory

@ TA = 25oC
@ TA = 100oC

VOLTS

IRM

VOLTS

1.2
150

250
2
100

500 (Note 3)

nS
A

CJ

40

pF

TJ, TSTG

-65 to +175

C
4.97ffspd300

H33

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSPD-300--2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

3 AMP HIGH RELIABILITY FAST RECOVERY DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES RGP300 - RGP310
500

JEDEC Method
8.3 mS Single
Half Sine Wave
TJ = 55 oC
100
Single Phase, Half wave, 60 Hz
Resistive and Inductive Loads
Lead Length = 0.375" (9.5 mm)

Ambient Temperature, oC

10
10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
100

10

TJ = 25 oC

1.0

10

0.1
TJ = 25 oC
Pulse Width = 300 S
1% Duty Cycle

0.1
0.1

0.01

Instantaneous Forward Voltage (Volts)

10

FIGURE 4. TYPICAL JUNCTION CAPACITANCE

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC

50
noninductive

Reverse Voltage, (Volts)

10
noninductive

TRR
0.5

D.U.T.

(+)

(-)

25 VDC
(APPROX)

0.0

PULSE
GENERATOR
(Note 2)

(-)
1
noninductive

(+)

-0.5

OSCILLOSCOPE
(Note 1)

-1.0
NOTES:
(1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF
(2) Rise time = 10nS max., source impedance = 50 ohms

Set time base

for 10nS/cm

1
cm

FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC

H34

4.97bfspd300

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSDP-601-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
RP600 PACKAGE

Low cost

SERIES RP600 - RP610

Low leakage

LL
Low forward voltage drop

BD (Dia)

High current capacity

BL

Color Band
Denotes
Cathode

Fast switching for high efficiency

MECHANICAL DATA

LL

Case: Molded epoxy (U/L Flammability Rating 94V-0)

LD (Dia)

Terminals: Plated axial leads

Soldering: Per MIL-STD 202 Method 208 guaranteed

Minimum
In
mm

Sym
Polarity: Color band denotes cathode

BL

0.340

Maximum
In
mm

8.6

0.360

9.1

Mounting Position: Any

BD

0.340

8.6

0.360

9.1

Weight: 0.07 Ounces (2.1 Grams)

LL
LD

1.00
0.048

25.4
1.2

0.052

1.3

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

RP600 RP601 RP602 RP604 RP606 RP608 RP610

Maximum DC Blocking Voltage

VRM

50

100

200

400

600

800

1000

Maximum RMS Voltage

VRMS

35

70

140

280

420

560

700

Maximum Peak Recurrent Reverse Voltage

VRRM

50

100

200

400

600

800

1000

Average Forward Rectified Current @ TA = 60 oC,

Lead length = 0.375 in. (9.5 mm)
Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)

IO

IFSM

300

AMPS

Maximum Forward Voltage at 6 Amps DC

VFM

Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)

TRR

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage
Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range
NOTES: (1) Lead length = 0.375 in. (9.5 mm)
(2) Measured at 1MHz & applied reverse voltage of 4 volts
(3) 300 nS avaiable - consult with factory

@ TA = 25oC
@ TA = 100oC

VOLTS

IRM

VOLTS

1.3
150

250
10
200

500 (Note 3)

nS
A

CJ

100

pF

TJ, TSTG

-65 to +175

C
01.00ffsdp601

H35

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSDP-601-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

6 AMP FAST RECOVERY DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES RP600 - RP610
500

400

JEDEC Method
8.3 mS Single
Half Sine Wave

300
Single Phase, Half wave, 60 Hz
Resistive and Inductive Loads
Lead Length = 0.375" (9.5 mm)

TJ = 25 oC
200

100
TJ = 150 oC

Ambient Temperature, oC

0
10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

1000
1000

100
TJ = 25 oC
f = 1 MHz

10

100

1.0

10

0.1

0.1

Instantaneous Forward Voltage (Volts)

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS
50
noninductive

10

Reverse Voltage, (Volts)

FIGURE 4. TYPICAL JUNCTION CAPACITANCE

10
noninductive

TRR
0.5

D.U.T.

(+)

(-)

25 VDC
(APPROX)

0.0

PULSE
GENERATOR
(Note 2)

(-)
1
noninductive

(+)

-0.5

OSCILLOSCOPE
(Note 1)

-1.0
NOTES:
(1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF
(2) Rise time = 10nS max., source impedance = 50 ohms

Set time base

for 10nS/cm

1
cm

FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC

H36

4.97bfsdp601

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSDG-800-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
Glass Passivated for high reliability/temperature performance

ACTUAL SIZE OF
TO-220AC PACKAGE

SERIES RGP800 - RGP806

Low switching noise

P

Low forward voltage drop

A
A1

D4

Low thermal resistance

D1

High surge current capability

Fast switching for high efficiency

B4

Low leakage
B3
3

MECHANICAL DATA

Case: TO-220 molded plastic (U/L Flammability Rating 94V-0)

Terminals: Plated rectangular pins
Solderability: Per MIL-STD 202 Method 208 guaranteed
Polarity: Marked on case
Mounting Position: Any
Weight: 0.07 Ounces (2.05 Grams)

A
A1
A2
B
B1
B2
B3
B4
C
D
D1
D2
D3
D4

D3

Minimum
mm
in

Sym

D2

Maximum
in
mm
0.187 4.75

B1

0.121*
0.14*
0.035
0.09
0.025*
0.050*

4.75*
3.56*
0.043 1.1
0.9
0.102 2.6
2.3
0.64*
1.27*
0.04
1.0
0.413 10.5
0.61 15.5
0.59 15.0
0.262* 6.6*
0.16
4.0
0.54 13.7
0.60 15.2
0.108* 2.75*
P 0.126* 3.2*
* These dimensions are "Typicals".

B2

B
B1

A2

TO - 220AC

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

UNITS

RGP800 RGP801 RGP802 RGP804

Series Number

RGP806

Maximum DC Blocking Voltage

VRM

50

100

200

400

600

Maximum RMS Voltage

VRMS

35

70

140

280

420

VRRM

50

100

200

400

600

Maximum Peak Recurrent Reverse Voltage

o

Average Forward Rectified Current @ Tc = 110 C

Peak Forward Surge Current ( 8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 8 Amps DC
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Thermal Resistance, Junction to Case

@ TC = 25 oC
@ TC = 100 oC

Typical Junction Capacitance (Note 1)

Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)
Junction Operating and Storage Temperature Range
NOTES: (1) Measured at 1MHz and an applied reverse voltage of 4 volts.

VOLTS

IO

IFSM

150

VFM

1.3

VOLTS
A

RJC

10
250
3

C/W

CJ

55

pF

IRM

TRR
TJ, TSTG

150

AMPS

200
-50 to +150

250

nSec
C
4.97ffsdg800

H37

DIOTEC ELECTRONICS CORP.

Data Sheet No. FSDG-800-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

8 AMP FAST RECOVERY DIODES

RATING & CHARACTERISTIC CURVES FOR SERIES RGP800 - RGP806
500
Resistive and Inductive Loads

400

Case

300

200
Ambient

NOTE 1
100

Temperature, oC

0
10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT

100

100

10

TC = 100 oC

10

1.0

TC = 75 oC

1.0

0.1

TC = 25 oC

0.01

0.1
0

Instantaneous Forward Voltage (Volts)

20

40

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 3. TYPICAL FORWARD CHARACTERISTICS

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

120
100

NOTES

80

(1) JEDEC Method, 8.3 mSec. Single Half Sine Wave, TJ = 150 oC

60

(2) TJ = 25 oC, Pulse Width = 300 Sec, 2.0% Duty Cycle

40

(3) TJ = 25 oC, f = 1 MHz

20

0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE

H38

4.97bfsdg800

SECTION I
HIGH
VOLTAGE
DIODES

STANDARD AND FAST RECOVERY

DO-41 PACKAGE
200 to 500 MILLIAMPERES
1200 to 5000 VOLTS
DO - 41

DIOTEC ELECTRONICS CORP.

- 18020 Hobart Blvd., Unit B - Gardena, CA 90248 U.S.A. - PH: 310-767-1052 - FX: 310-767-7958

DIOTEC ELECTRONICS CORP.

Data Sheet No. HVGP-1000-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-41 PACKAGE

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

SERIES GP1120 - GP1500

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES

LOW FORWARD VOLTAGE DROP

BL
Color Band
Denotes
Cathode

HIGH CURRENT CAPABILITY

MECHANICAL DATA

LL
DO-41

Case: JEDEC DO-41 molded plastic

(U/L Flammability Rating 94V-0)

LD (Dia)

Terminals: Plated axial leads

Soldering: Per MIL-STD 202 Method 208 guaranteed
Polarity: Color band denotes cathode

Minimum
In
mm
0.160
4.1

Maximum
In
mm
5.2
0.205

BD

0.103

2.6

0.107

2.7

LL
LD

1.00
0.028

25.4
0.71

0.034

0.86

Sym

Mounting Position: Any

BL

Weight: DO-41 - 0.012 Ounces (0.34 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

GP
1150

GP
1180

GP
1200

GP
1250

GP
1300

GP
1400

GP
1500

GP
1600

Maximum DC Blocking Voltage

VRM

1500

1800

2000

2500

3000

4000

5000

6000

Maximum RMS Voltage

VRMS

1050

1260

1400

1750

2100

2800

3500

4200

Maximum Peak Recurrent Reverse Voltage

VRRM

1500

1800

2000

2500

3000

4000

5000

6000

Average Forward Rectified Current @ TA = 50 oC,

Lead length = 0.375 in. (9.5 mm)
Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at Rated Forward Current
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Typical Junction Capacitance (Note 1)
Operating and Storage Temperature Range
NOTES: (1) Measured at 1MHz & applied reverse voltage of 4 volts

@ TA = 25 C

VOLTS

IO

1000

500

200

mA

IFSM

35

25

15

AMPS

VFM

1.5

3.0

IRM

1.0

4.5

6.0

VOLTS
A

CJ

12

pF

TJ, TSTG

-65 to +150

C
2.01gp1120

I1

DIOTEC ELECTRONICS CORP.

Data Sheet No. HVGP-1000-2B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

HIGH VOLTAGE DIODE RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES GP1150 - GP1600
50
GP1150-1200
Single Phase, Half wave, 60 Hz
Resistive and Inductive Loads
Lead Length = 0.375" (9.5 mm)

40
JEDEC Method
8.3 mS Half Sine Wave
30

GP1250-1400
20
GP1500-1600
10

Ambient Temperature, oC

0
10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
100

1000

TJ = 100 oC
GP1250-1400
10

100

1.0
TJ = 25 oC

TJ = 25 oC
Non-repetitive Square Pulse
10
0.01

0.1

1.0

10

Pulse Duration (Milliseconds)

0.1

FIGURE 6. PEAK FORWARD SURGE CURRENT

20

60

80

100

120

140

Percent of Rated Peak Reverse Voltage

FIGURE 4. TYPICAL REVERSE CHARACTERISTICS

100
TJ = 25 oC

10

0.1
0.1

10

100

Reverse Voltage, (Volts)

FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE

I2

4.97bhvgp100

DIOTEC ELECTRONICS CORP.

Data Sheet No. HVRP-1000-1C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

ACTUAL SIZE OF
DO-41 PACKAGE

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

SERIES RP1120 - RP1500

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

LL
BD (Dia)

EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES

LOW FORWARD VOLTAGE DROP

BL
Color Band
Denotes
Cathode

HIGH CURRENT CAPABILITY

MECHANICAL DATA

LL
DO-41

Case: JEDEC DO-41 molded plastic

(U/L Flammability Rating 94V-0)
Terminals: Plated axial leads

LD (Dia)

Soldering: Per MIL-STD 202 Method 208 guaranteed

Polarity: Color band denotes cathode

Minimum
In
mm

BL

0.160

4.1

Maximum
In
mm
5.2
0.205

BD

0.103

2.6

0.107

2.7

LL
LD

1.00
0.028

25.4
0.71

0.034

0.86

Sym

Mounting Position: Any

Weight: DO-41 - 0.012 Ounces (0.34 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

RGP
1120

RGP
1150

RGP
1180

RGP
1200

RGP
1250

RGP
1300

RGP
1400

RGP
1500

Maximum DC Blocking Voltage

VRM

1200

1500

1800

2000 2500

3000

4000

5000

Maximum RMS Voltage

VRMS

840

1050

1260

1400 1750

2100

2800

3500

Maximum Peak Recurrent Reverse Voltage

VRRM

1200

1500

1800

2000 2500

3000

4000

5000

Average Forward Rectified Current @ TA = 50 oC

(Lead length = 0.375 in. (9.5 mm))

VOLTS

IO

800

400

200

mA

Peak Forward Surge Current (8.3 mSec single half sine wave
superimposed on rated load)

IFSM

30

20

10

AMPS

Maximum Forward Voltage at Rated Forward Current

VFM

2.5

4.5

6.5

VOLTS

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage

@ TA = 25 C

Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A)

Operating and Storage Temperature Range

IRM

1.0

TRR

500

nS

TJ, TSTG

-65 to +125

-65 to +150

C
2.01rgp1120

I3

DIOTEC ELECTRONICS CORP.

Data Sheet No. HVRP-1000-2C

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

HIGH VOLTAGE FAST RECOVERY RECTIFIERS

RATING & CHARACTERISTIC CURVES FOR SERIES RGP1120 - RGP1500
50

Single Phase, Half wave, 60 Hz

Resistive and Inductive Loads
Lead Length = 0.375" (9.5 mm)

RGP1120-1180

40
JEDEC Method
8.3 mS Half Sine Wave
30

RGP1200-1300
20
RGP1400-1500
10

Ambient Temperature, oC

0
10

FIGURE 1. FORWARD CURRENT DERATING CURVE

100

Number of Cycles at 60 Hz
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
100

10
o

TJ = 25 C
Pulse Width = 300 S
1% Duty Cycle

1.0

10

0.1

0.1
0.1

0.01

Instantaneous Forward Voltage (Volts)

10

FIGURE 4. TYPICAL JUNCTION CAPACITANCE

FIGURE 3. TYPICAL FORWARD CHARACTERISTIC

50
noninductive

Reverse Voltage, (Volts)

10
noninductive

TRR
0.5

D.U.T.

(+)

(-)

25 VDC
(APPROX)

0.0

PULSE
GENERATOR
(Note 2)

(-)
1
noninductive

(+)

-0.5

OSCILLOSCOPE
(Note 1)

-1.0
NOTES:
(1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF
(2) Rise time = 10nS max., source impedance = 50 ohms

Set time base

for 10nS/cm

1
cm

FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC

I4

4.97bhvrp100

AUTOMOTIVE DIODES

Transient Voltage
Suppressors
(Section J)

PRESS FIT

MOLDED PRODUCTS

DIODE CELLS

AXIAL LEAD

Standard Diodes
(Section K)

MOLDED PRODUCTS

DIODE CELLS

DIOTEC ELECTRONICS CORP. - 18020 Hobart Blvd., Unit B - Gardena, CA 90248 U.S.A. - PH: 310-767-1052 - FX: 310-767-7958

SECTION J
AUTOMOTIVE DIODES
TRANSIENT VOLTAGE
SUPPRESSORS

PRESS FIT

MOLDED PRODUCTS

DIODE CELLS

AXIAL LEAD

DIOTEC ELECTRONICS CORP. - 18020 Hobart Blvd., Unit B - Gardena, CA 90248 U.S.A. - PH: 310-767-1052 - FX: 310-767-7958

DIOTEC ELECTRONICS CORP

Data Sheet No. TPFD-3501-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE
VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM
MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

_ 0.002
0.050 +

Large die for high power capability

_ 0.005 x 45O
0.016 +

Very low forward voltage drop

_ 0.005
0.184 +

Increased capacity by parallel operation

Protects expensive automotive electronics and
mobile equipment

+ 0.020
1.150 _
_ 0.007
0.354 +
0.160 + 0.013

Color Coded
Polarity Mark
& Part No.

MECHANICAL DATA
Case: Nickel plated copper

0.032 + 0.007

0.502 + 0.004

Finish: All external surfaces are corrosion resistant

and the contact areas are readily solderable
Soldering Temperature: 250 oC maximum
Mounting Position: Any. Maximum force used for diode
insertion to be 12 KN

ALL DIMENSIONS IN INCHES

Polarity: Color coded polarity mark and part number

on cap base (ANODE on LEAD: Part No.=TVS3527PFA)
(CATHODE on LEAD; Part No.=TVS3527PFC)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

TVS3527PFC

TVS3527PFA

23

23

Maximum Recurrent Peak Reverse Voltage

VRRM

Working Peak Reverse Voltage

VRWM

Maximum DC Blocking Voltage

VDC

Breakdown Voltage (IR = 100 mA dc, Tc = 25 oC)

V(BR)

24 Min / 32 Max

24 Min / 32 Max

IO

35

35

IFSM

600

600

IRSM

110

110

1.05
1.00
200

1.05
1.00

VOLTS

200

nA

0.8

0.8

C/W

Average Forward Rectified Current

Non-repetitive Peak Forward Surge Current
(Half wave, single phase, 60 Hz sine applied to rated load)
Repetitive Peak Reverse Surge Current (Time Constant = 10 mSec
Duty Cycle < 1.0%, Tc = 25 oC)
Instantaneous Forward Voltage
Maximum
(IF = 100A@ 300 Secpulse, TC = 25oC)
Typical
O

Maximum DC Reverse Current (V R = 20V DC, Tc = 25 C)

Maximum Thermal Resistance, Junction to Case (Note 1)
Junction Operating & Storage Temperature Range
Notes: 1) Single Side Cooled

VF
IR
RJC
TJ,TSTG

-65 to +175

-65 to +175

VOLTS

AMPS

C
3.01tvs3527pf

J1

DIOTEC ELECTRONICS CORP

Data Sheet No. TPFD-6001-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE
VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM
MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

_ 0.002
0.050 +

Large die for high power capability

_ 0.005 x 45O
0.016 +

Very low forward voltage drop

_ 0.005
0.184 +

Increased capacity by parallel operation

Protects expensive automotive electronics and
mobile equipment

+ 0.020
1.150 _
_ 0.007
0.354 +
0.160 + 0.013

Color Coded
Polarity Mark
& Part No.

MECHANICAL DATA
Case: Nickel plated copper

0.032 + 0.007

0.502 + 0.004

Finish: All external surfaces are corrosion resistant

and the contact areas are readily solderable
Soldering Temperature: 250 oC maximum
Mounting Position: Any. Maximum force used for diode
insertion to be 12 KN

ALL DIMENSIONS IN INCHES

Polarity: Color coded polarity mark and part number

on cap base (ANODE on LEAD: Part No.=TVS6027PFA)
(CATHODE on LEAD; Part No.=TVS6027PFC)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number

UNITS

TVS6027PFC

TVS6027PFA

23

23

Maximum Recurrent Peak Reverse Voltage

VRRM

Working Peak Reverse Voltage

VRWM

Maximum DC Blocking Voltage

VDC

Breakdown Voltage (IR = 100 mA dc, Tc = 25 oC)

V(BR)

24 Min / 32 Max

24 Min / 32 Max

IO

60

60

IFSM

800

800

IRSM

140

140

1.05
1.00
200

1.05
1.00

VOLTS

200

nA

0.8

0.8

C/W

Average Forward Rectified Current

Non-repetitive Peak Forward Surge Current
(Half wave, single phase, 60 Hz sine applied to rated load)
Repetitive Peak Reverse Surge Current (Time Constant = 10 mSec
Duty Cycle < 1.0%, Tc = 25 oC)
Instantaneous Forward Voltage
Maximum
(IF = 100A@ 300 Secpulse, TC = 25oC)
Typical
O

Maximum DC Reverse Current (V R = 20V DC, Tc = 25 C)

Maximum Thermal Resistance, Junction to Case (Note 1)
Junction Operating & Storage Temperature Range
Notes: 1) Single Side Cooled

VF
IR
RJC
TJ,TSTG

-65 to +175

-65 to +175

VOLTS

AMPS

C
3.01tvs6027pf

J3

DIOTEC ELECTRONICS CORP

Data Sheet No. TSBD-3500-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.180" x 0.180"
Square

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION

Color Ring
Denotes Cathode

D
Large die for high power capability

Very low forward voltage drop

Increased capacity by parallel operation

Protects expensive automotive electronics and
mobile equipment

MECHANICAL DATA
Case: Transfer molded plastic
MILLIMETERS

Finish: All external surfaces are silver plated for corrosion

resistance superior solderability

DIM

Soldering Temperature: 250 oC maximum

Mounting Position: Any
Polarity: Color band denotes cathode

INCHES

MIN

MAX

MIN

MAX

9.78

10.29

0.385

0.405

6.05

6.20

0.238

0.244

5.54

5.60

0.218

0.220

4.19

4.45

0.165

0.175

5 NOM

5 NOM

Weight: 0.6 Ounces (1.8 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz resistive or inductive load.

PARAMETER (TEST CONDITIONS)

SYMBOL

RATINGS

UNITS

TVS3527

Series Number
Maximum Recurrent Peak Reverse Voltage

VRRM

Working Peak Reverse Voltage

VRWM

Maximum DC Blocking Voltage

VDC

Breakdown Voltage (IR = 100 mA dc, Tc = 25 oC)

V(BR)

24 Min / 32 Max

IO

35

IFSM

600

IRSM

110

VF

1.05
1.00

VOLTS

IR

200

nA

0.8

C/W

Average Forward Rectified Current

Non-repetitive Peak Forward Surge Current
(Half wave, single phase, 60 Hz sine applied to rated load)
Repetitive Peak Reverse Surge Current (Time Constant = 10 mSec
Duty Cycle < 1.0%, Tc = 25 oC)
Instantaneous Forward Voltage
Maximum
(IF = 100A @ 300 Sec pulse, TC = 25oC)
Typical
O

Maximum DC Reverse Current (VR = 20V DC, Tc = 25 C)

Maximum Thermal Resistance, Junction to Case (Note 1)
Junction Operating & Storage Temperature Range
Notes: 1) Single Side Cooled

RJC
TJ,TSTG

23

-65 to +175

VOLTS

AMPS

C
3.01 tvs35

J5

DIOTEC ELECTRONICS CORP

Data Sheet No. TSBD-3500S-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.180" x 0.180"
Square

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION

Color Ring
Denotes Cathode

D
Large die for high power capability

Very low forward voltage drop

Increased capacity by parallel operation

Protects expensive automotive electronics and
mobile equipment

MECHANICAL DATA
Case: Transfer molded plastic
MILLIMETERS

Finish: All external surfaces are silver plated for corrosion

resistance superior solderability

DIM

Soldering Temperature: 250 oC maximum

Mounting Position: Any
Polarity: Color band denotes cathode

INCHES

MIN

MAX

MIN

MAX

8.43

8.69

0.332

0.342

5.94

6.25

0.234

0.246

5.46

5.71

0.215

0.225

4.19

4.45

0.165

0.175

5 NOM

5 NOM

Weight: 0.6 Ounces (1.8 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz resistive or inductive load.

PARAMETER (TEST CONDITIONS)

SYMBOL

RATINGS

UNITS

TVS3527S

Series Number
Maximum Recurrent Peak Reverse Voltage

VRRM

Working Peak Reverse Voltage

VRWM

Maximum DC Blocking Voltage

VDC

Breakdown Voltage (IR = 100 mA dc, Tc = 25 oC)

V(BR)

24 Min / 32 Max

IO

35

IFSM

600

IRSM

110

VF

1.05
1.00

VOLTS

IR

200

nA

0.8

C/W

Average Forward Rectified Current

Non-repetitive Peak Forward Surge Current
(Half wave, single phase, 60 Hz sine applied to rated load)
Repetitive Peak Reverse Surge Current (Time Constant = 10 mSec
Duty Cycle < 1.0%, Tc = 25 oC)
Instantaneous Forward Voltage
Maximum
(IF = 100A @ 300 Sec pulse, TC = 25oC)
Typical
O

Maximum DC Reverse Current (VR = 20V DC, Tc = 25 C)

Maximum Thermal Resistance, Junction to Case (Note 1)
Junction Operating & Storage Temperature Range
Notes: 1) Single Side Cooled

RJC
TJ,TSTG

23

-65 to +175

VOLTS

AMPS

C
3.01tvs35s

J7

Data Sheet No. TSBD-3500D-1B

DIOTEC ELECTRONICS CORP

18020 Hobart Blvd., Unit B
Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES

Die Size:
0.180" x 0.180"
Square

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
R

D
A

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Soft Glass
Passivation
G

Large die for high power capability

Silicon Die

Silver Plated
Copper Slugs

Very low forward voltage drop

Built-in stress relief mechanism for die protection

Silver plated substrates for corrosion resistance and

superior soldeability

MILLIMETERS
DIM

INCHES

MIN

MAX

MIN

MAX

Soldering temperature: 250 oC maximum

5.33

5.46

0.210

0.215

2.03

2.16

0.080

0.085

Protects expensive automotive electronics and mobile

equipment

4.70

4.83

0.185

0.190

F
G

0.64
0.96

0.76
1.09

0.025
0.038

0.030
0.043

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

SYMBOL

UNITS

TVS3527D

Series Number
Maximum Recurrent Peak Reverse Voltage

VRRM

Working Peak Reverse Voltage

VRWM

Maximum DC Blocking Voltage

23
VOLTS

VDC
o

Breakdown Voltage (IR = 100 mA dc, Tc = 25 C)

Average Rectified Forward Current (Single phase, Resistive load,
60 Hz)
Non-repetitive Peak Forward Surge Current
(Half wave, Single phase, 60 Hz sine applied to rated load)
Repetitive Peak Reverse Surge Current (Time constant = 10 mSec
Duty cycle < 1.0%, Tc = 25 o C)
Instantaneous Forward Voltage
Maximum
Typical
(IF = 80A @300 Sec pulse, TC = 25oC)
O

Maximum DC Reverse Current (VR = 20V DC, Tc = 25 C)

Maximum Thermal Resistance, Junction to Lead (Note 1)
Junction Operating & Storage Temperature Range
Notes: 1) Single Side Cooled

RATINGS

V(BR)

24 Min / 32 Max

IO

35

IFSM

500

IRSM

110

VF

1.05
1.00

VOLTS

IR

200

nA

RJC

0.8

C/W

TJ,TSTG

-65 to +175

AMPS

3.01 tvs35d

J9

DIOTEC ELECTRONICS CORP

Data Sheet No. TSBD-5000-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.216" Flat to Flat
Hex

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION

Color Ring
Denotes Cathode

INDUSTRYS LARGEST DIE FOR HIGHEST

POWER CAPABILITY

A
M

Very low forward voltage drop

Increased capacity by parallel operation
Protects expensive automotive electronics and
mobile equipment

MECHANICAL DATA
Case: Transfer molded plastic
MILLIMETERS

Finish: All external surfaces are silver plated for corrosion

resistance superior solderability

DIM

Soldering Temperature: 250 oC maximum

Mounting Position: Any
Polarity: Color band denotes cathode

INCHES

MIN

MAX

MIN

MAX

9.78

10.29

0.385

0.405

6.05

6.20

0.238

0.244

5.54

5.60

0.218

0.220

4.19

4.45

0.165

0.175

5 NOM

5 NOM

Weight: 0.6 Ounces (1.8 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz resistive or inductive load.

PARAMETER (TEST CONDITIONS)

SYMBOL

RATINGS
TVS5027

Series Number
Maximum Recurrent Peak Reverse Voltage

VRRM

Working Peak Reverse Voltage

VRWM

Maximum DC Blocking Voltage

VDC

Breakdown Voltage (IR = 100 mA dc, Tc = 25 oC)

V(BR)

24 Min / 32 Max

IO

50

IFSM

800

IRSM

140

Average Forward Rectified Current

Non-repetitive Peak Forward Surge Current
(Half wave, single phase, 60 Hz sine applied to rated load)
Repetitive Peak Reverse Surge Current (Time Constant = 10 mSec
Duty Cycle < 1.0%, Tc = 25 oC)
Instantaneous Forward Voltage
Maximum
(IF = 100A@ 300 Secpulse, TC = 25o C)
Typical
O

Maximum DC Reverse Current (VR = 20V DC, Tc = 25 C)

Maximum Thermal Resistance, Junction to Case (Note 1)
Junction Operating & Storage Temperature Range
Notes: 1) Single Side Cooled

UNITS

VF
IR
RJC
TJ,TSTG

23

1.05
1.00
200
0.8
-65 to +175

VOLTS

AMPS

VOLTS
nA
C/W
C
1.99ftsbd050

J11

DIOTEC ELECTRONICS CORP

Data Sheet No. TSBD-5000S-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.216" Flat to Flat
Hex

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION

Color Ring
Denotes Cathode

INDUSTRYS LARGEST DIE FOR HIGHEST

POWER CAPABILITY

A
M

Very low forward voltage drop

Increased capacity by parallel operation
Protects expensive automotive electronics and
mobile equipment

MECHANICAL DATA
Case: Transfer molded plastic
MILLIMETERS

Finish: All external surfaces are silver plated for corrosion

resistance superior solderability

DIM

Soldering Temperature: 250 oC maximum

Mounting Position: Any
Polarity: Color band denotes cathode

INCHES

MIN

MAX

MIN

MAX

8.43

8.69

0.332

0.342

5.94

6.25

0.234

0.246

5.46

5.71

0.215

0.225

4.19

4.45

0.165

0.175

5 NOM

5 NOM

Weight: 0.6 Ounces (1.8 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz resistive or inductive load.

PARAMETER (TEST CONDITIONS)

SYMBOL

RATINGS

UNITS

TVS5027S

Series Number
Maximum Recurrent Peak Reverse Voltage

VRRM

Working Peak Reverse Voltage

VRWM

Maximum DC Blocking Voltage

VDC

Breakdown Voltage (IR = 100 mA dc, Tc = 25 oC)

V(BR)

24 Min / 32 Max

IO

50

IFSM

800

IRSM

140

VF

1.05
1.00

VOLTS

IR

200

nA

RJC

0.8

C/W

TJ,TSTG

-65 to +175

Average Forward Rectified Current

Non-repetitive Peak Forward Surge Current
(Half wave, single phase, 60 Hz sine applied to rated load)
Repetitive Peak Reverse Surge Current (Time Constant = 10 mSec
Duty Cycle < 1.0%, Tc = 25 oC)
Instantaneous Forward Voltage
Maximum
Typical
(IF = 100A@ 300 Secpulse, TC = 25oC)
O

Maximum DC Reverse Current (VR = 20V DC, Tc = 25 C)

Maximum Thermal Resistance, Junction to Case (Note 1)
Junction Operating & Storage Temperature Range
Notes: 1) Single Side Cooled

23

VOLTS

AMPS

1.99ftsbd050

J13

DIOTEC ELECTRONICS CORP

Data Sheet No. TVSP6-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

ACTUAL SIZE OF
DO-41 PACKAGE

SERIES P6KE6.8 - P6KE400CA

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
600 Watt peak power capability on 10/1000 S waveform
DO - 41
Excellent clamping capability

LL

Repetition rate (Duty Cycle): 0.01%

BD (Dia)

Low incremental surge resistance

Fast response time (0 to BV Volts)
BL

Unidirectional - typically less than 1pS

Color Band
Denotes
Cathode

Bidirectional - typically less then 5nS

Typical Reverse Leakage (ID) less than 1A above 10 Volts

LL

MECHANICAL DATA
LD (Dia)

Case: JEDEC DO-41 molded epoxy (UL Flammability Rating 94V-O)

Terminals: Plated Axial Leads

Minimum
In
mm

Sym
Soldering: Per MIL-STD 202 Method 208 guaranteed

0.160

4.1

0.205

5.2

BD

0.103

2.6

0.107

2.7

LL
LD

1.00
0.028

25.4
0.71

0.034

0.86

BL

Mounting Position: Any

Polarity: Color band denotes cathode
Weight: 0.012 Ounces (0.34 Grams)

Maximum
In
mm

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified. Resistive or inductive load.

PARAMETER (TEST CONDITIONS)

Peak Pulse Power Dissipation on 10/1000S Waveform (Note 1, Fig 1)
Peak Pulse Current on 10/1000mS Waveform (Note 1, Fig 1)
Steady State Power Dissipation at TL= 75 OC With Lead Length =0.375" (9.5mm) (Note 2)
Peak Forward Surge Current (8.3mS Single Half Sine Wave Superimposed
on Rated Load - JEDEC Method) Unidirectional Only. (Note 2)
Maximum Instantaneous Forward Voltage at 50A; Unidirectional Only (Note 2)
Junction Operating & Storage Temperature Range

SYMBOL

RATINGS

UNITS

PPPM

Minimum 600

WATTS

IPPM

See Table 1

AMPS

PM(AV)

5.0

WATTS

IFSM

100

AMPS

VF

3.5

VOLTS

TJ,TSTG

-65 to +175

C/W

Notes:
o
1) Non-Repetitive Current Pulse Per Fig. 3 and Derated Above TA=25 C Per Fig 2.
2) Mounted on Copper Leaf Area of 1.58 in2 (40mm2) Per Fig 5.
3) 8.3mS Single Half Sine Wave or Equivalent Square Wave. Duty Cycle =4 Pulses Per Minute Maximum.

J15

DIOTEC ELECTRONICS CORP.

Data Sheet No. TVSP6-2A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

600 WATT TRANSIENT VOLTAGE SUPPRESSORS

RATINGS AND CHARACTERISTIC CURVES FOR SERIES P6KE6.8 - P6KE400CA
100
Non-Reptitive Pulse
Waveform Shown in
Figure 3
TA=25 OC
10

1.0

0.1
0.1

1.0S

10S

100S

1.0mS

10mS

Ambient Temperature, TA ( oC)

FIGURE 2. PULSE DERATING CURVE

Pulse Width, td (Sec)

FIGURE 1. PEAK PULSE POWER RATING CURVE
6000

TJ = 25 OC
t=10S

TA=25 OC
Pulse Width (td) is defined
as the point where the
peak current decays to
50% of IPPM

Measured at
Zero Bias
1000
Measured at
Standoff
Voltage (VWM)

100

-kt
TJ=25 OC
f=1.0 Mhz
VSIG=50mVP-P

Time, t (mS)
FIGURE 3. PULSE WAVEFORM

10
1.0

10

100

200

Breakdown Voltage (VBR), Volts

FIGURE 4. TYPICAL JUNCTION CAPACITANCE-UNIDIRECTIONAL

200
8.3mS Single Half Sine Wave
JEDEC METHOD

100

40mmx40mmx1mm
CopperHeatSinks
(1.58"x1.58"x0.40")

10
1

Lead Temperature, TL ( oC)

FIGURE 5. STEADY STATE POWER DERATING CURVE

J16

100

Number of Cycles at 60Hz

FIGURE 6. MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT - UNIDIRECTIONAL

4.97bgppd300

DIOTEC ELECTRONICS CORP.

Data Sheet No. TVSP6-3A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

600 WATT TRANSIENT VOLTAGE SUPPRESSORS

RATINGS AND CHARACTERISTIC CURVES FOR SERIES P6KE6.8 - P6KE400CA
FOR BIDIRECTIONAL APPLICATIONS: USE "C" OR "CA" FOR TYPES P6KE6.8-PKE440.

FOR EXAMPLE: P6KE6.8C OR P6KE400CA.

ELECTRICAL CHARACTERISTICS APPLY IN BOTH DIRECTIONS.

BREAKDOWN VOLTAGE (VBR)

(NOTE 1)
PART
NO.

*P6KE6.8
*P6KE6.8A
*P6KE7.5
*P6KE7.5A
*P6KE8.2
*P6KE8.2A
*P6KE9.1
*P6KE9.1A
*P6KE10
*P6KE10A
*P6KE11
*P6KE11A
*P6KE12
*P6KE12A
*P6KE13
*P6KE13A
*P6KE15
*P6KE15A
*P6KE16
*P6KE16A
*P6KE18
*P6KE18A
*P6KE20
*P6KE20A
*P6KE22
*P6KE22A
*P6KE24
*P6KE24A
*P6KE27
*P6KE27A
*P6KE30
*P6KE30A
*P6KE33
*P6KE33A
*P6KE36
*P6KE36A
*P6KE39
*P6KE39A
*P6KE43
*P6KE43A
*P6KE47
*P6KE47A

VOLTS
MIN

MAX

@ IT
(mA)

6.12
6.45
6.75
7.13
7.38
7.79
8.19
8.65
9.00
9.50
9.90
10.5
10.8
11.4
11.7
12.4
13.5
14.3
14.4
15.2
16.2
17.1
18.0
19.0
19.8
20.9
21.6
22.8
24.3
25.7
27.0
28.5
29.7
31.4
32.4
34.2
35.1
37.1
38.7
40.9
42.3
44.7

7.48
7.14
8.25
7.88
9.02
8.61
10.0
9.55
11.0
10.5
12.1
11.6
9.40
13.2
12.6
14.3
13.7
16.5
15.8
17.6
16.8
19.8
18.9
22.0
21.0
24.2
23.1
26.4
25.2
29.7
28.4
33.0
31.5
36.3
34.7
39.6
37.8
42.9
41.0
47.3
45.2
51.7
49.4

10
10
10
10
10
10
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0

VWM
(VOLTS)

MAX. ID
@ VWM
(A)
(Note 3)

5.50
5.80
6.05
6.40
6.63
7.02
7.37
7.78
8.10
8.55
8.92
9.40
9.72
10.2
10.5
11.1
12.1
12.8
12.9
13.6
14.5
15.3
16.2
17.1
17.8
18.8
19.4
20.5
21.8
23.1
24.3
25.6
26.8
28.2
29.1
30.8
31.6
33.3
34.8
36.8
38.1
40.2

1000
1000
500
500
200
200
50
50
10
10
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0

MAX. IPPM
(AMPS)
(Note 2)

VC
@ IPPM
(VOLTS)

MAX.
TEMPERATURE
COEFFICIENT
OF V(BR)
(% O C)

56
57
51
53
48
50
44
45
40
41
37
38
35
36
32
33
27
28
26
27
23
24
21
22
19
20
17
18
15
16
14
14.4
12.6
13.2
11.6
12.0
12
10.6
11.2
9.6
10.1
8.9
9.3

10.8
10.5
11.7
11.3
12.5
12.1
13.8
13.4
15.0
14.5
16.2
15.6
17.3
16.7
19.0
18.2
22.0
21.2
23.5
22.5
26.5
25.2
29.1
27.7
31.9
30.6
34.7
33.2
39.1
37.5
43.5
41.4
47.7
45.7
52.0
49.9
56.4
53.9
61.9
59.3
67.8
64.8

0.057
0.057
0.061
0.061
0.065
0.065
0.068
0.068
0.073
0.073
0.075
0.075
0.078
0.078
0.061
0.081
0.084
0.084
0.086
0.086
0.088
0.088
0.090
0.090
0.092
0.092
0.094
0.094
0.096
0.096
0.097
0.097
0.098
0.098
0.099
0.099
0.100
0.100
0.101
0.101
0.101
0.101

Table Symbols:
1. V(BR) measured after IT applied for 300S, IT=square wave pulse or equivalent
2. Surge current waveform per Figure 3 and derate per Figure 2.
3. For Bidirectional types with VR of 10 Volts and less, the IP limit is doubled
4. All Terms and Symbols are consistant with ANSI/IEEE C62.35

ID - Reverse Leakage Current

IPPM - Maximum Peak Pulse Current
IT - Test Current (To Determine VBR)
mA - Milliamperes
Max. - Maximum
Min - Minimum

V(BR) - Breakdown Voltage

VC - Clamping Voltage
VWM - Reverse Standoff Voltage
% - Per Cent
o
C - Degrees Celsius

J17

DIOTEC ELECTRONICS CORP.

Data Sheet No. TVSP6-4A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

600 WATT TRANSIENT VOLTAGE SUPPRESSORS

RATINGS AND CHARACTERISTIC CURVES FOR SERIES P6KE6.8 - P6KE400CA
FOR BIDIRECTIONAL APPLICATIONS: USE "C" OR "CA" FOR TYPES P6KE6.8-PKE440.

FOR EXAMPLE: P6KE6.8C OR P6KE400CA.

ELECTRICAL CHARACTERISTICS APPLY IN BOTH DIRECTIONS.

BREAKDOWN VOLTAGE (VBR)

(NOTE 1)
PART
NO.

P6KE51
P6KE51A
P6KE56
P6KE56A
P6KE62
P6KE62A
P6KE68
P6KE68A
P6KE75
P6KE75A
P6KE82
P6KE82A
P6KE91
P6KE91A
P6KE100
P6KE100A
P6KE110
P6KE110A
P6KE120
P6KE120A
P6KE130
P6KE130A
P6KE150
P6KE150A
P6KE160
P6KE160A
P6KE170
P6KE170A
P6KE180
P6KE180A
P6KE200
P6KE200A
P6KE220
P6KE220A
P6KE250
P6KE250A
P6KE300
P6KE300A
P6KE350
P6KE350A
P6KE400
P6KE400A
P6KE440
P6KE440A

VOLTS
MIN

MAX

@ IT
(mA)

45.9
48.5
50.4
53.2
55.8
58.9
61.2
64.6
67.5
71.3
73.8
77.9
81.90
81.9
86.50
86.5
90.00
90.0
95.00
95.0
99.00
99.0
105
108
114
117
124
135
143
144
152
153
162
162
171
180
190
198
209
225
237
270
285
315
332
360
380
396
418

56.1
53.6
61.6
58.8
68.2
65.1
74.8
71.4
82.5
78.8
90.2
86.1
100
95.5
110
105
121
116
132
126
143
137
165
158
176
168
187
179
198
189
220
210
242
231
275
263
330
315
385
368
440
420
484
462

1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0

VWM
(VOLTS)

MAX. ID
@ VWM
(A)
(Note 3)

41.3
43.6
45.4
47.8
50.2
53.0
55.1
58.1
60.7
64.1
66.4
70.1
79.7
73.7
77.8
81.0
85.5
89.2
94.0
97.2
102
105
111
121
128
130
136
138
145
146
154
162
171
175
185
202
214
243
256
284
300
324
342
356
376

5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0

MAX. IPPM
(AMPS)
(Note 2)

8.2
8.6
7.4
7.8
6.8
7.1
6.1
6.5
5.5
5.8
5.1
5.3
4.5
4.8
4.2
4.4
3.8
4.0
3.5
3.6
3.2
3.3
2.8
2.9
2.6
2.7
2.5
2.6
2.3
2.4
2.1
2.2
1.75
1.83
1.67
1.75
1.40
1.45
1.20
1.25
1.05
1.10
0.95
1.00

VC
@ IPPM
(VOLTS)

MAX.
TEMPERATURE
COEFFICIENT
OF V(BR)
(% OC)

73.5
70.1
80.5
77.0
89.0
85.0
98.0
92.0
108
103
118
113
131
125
144
137
158
152
173
165
187
179
215
207
230
219
244
234
258
246
287
274
344
328
360
344
430
414
504
482
574
548
631
602

0.102
0.102
0.103
0.103
0.104
0.104
0.104
0.104
0.105
0.105
0.105
0.105
0.106
0.106
0.106
0.106
0.107
0.107
0.107
0.107
0.107
0.107
0.108
0.108
0.108
0.108
0.108
0.108
0.108
0.108
0.108
0.108
0.108
0.108
0.110
0.110
0.110
0.110
0.110
0.110
0.110
0.110
0.110
0.110
Table Symbols:

1. V(BR) measured after IT applied for 300S, IT=square wave pulse or equivalent
2. Surge current waveform per Figure 3 and derate per Figure 2.
3. For Bidirectional types with VR of 10 Volts and less, the IP limit is doubled
4. All Terms and Symbols are consistant with ANSI/IEEE C62.35

J18

ID - Reverse Leakage Current

IPPM - Maximum Peak Pulse Current
IT - Test Current (To Determine VBR)
mA - Milliamperes
Max. - Maximum
Min - Minimum

V(BR) - Breakdown Voltage

VC - Clamping Voltage
VWM - Reverse Standoff Voltage
% - Per Cent
o
C - Degrees Celsius

SECTION K
AUTOMOTIVE DIODES
STANDARD DIODES

MOLDED PRODUCTS

DIODE CELLS

DIOTEC ELECTRONICS CORP.

- 18020 Hobart Blvd., Unit B - Gardena, CA 90248 U.S.A. - PH: 310-767-1052 - FX: 310-767-7958

DIOTEC ELECTRONICS CORP.

Data Sheet No. BUDI-1200D-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

Die Size:
0.120"
Round

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

D
A

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Soft Glass
Passivation
G

Large die for high power capability

B
Silver Plated
Copper Slugs

Very low forward voltage drop

Silicon Die

Built-in stress relief mechanism for die protection

MILLIMETERS

Silver plated substrates for easy soldering or installation

DIM

MIN

MAX

MIN

MAX

3.86

4.06

0.152

0.160

1.98

2.18

0.078

0.086

3.07

3.28

0.121

0.129

Soldering temperature: 250 C maximum

Protects expensive automotive electronics and mobile

equipment

INCHES

F
G

0.76 Typ
1.02 Typ

0.030 Typ
0.040 Typ

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

Maximum Recurrent Peak Reverse Voltage

VRRM

Working Peak Reverse Voltage

VRWM

Maximum DC Blocking Voltage

VDC

Non-repetitive Peak Reverse Voltage

(Half wave, Single phase, 60Hz peak)

VRSM

Average Rectified Forward Current (Single phase, Resistive load,

60Hz)
Non-repetitive Peak Forward Surge Current
(Half wave, Single phase, 60Hz sine applied to rated load)

Maximum DC Reverse Current

At Rated DC Blocking Voltage
Operating & Storage Temperature Range

UNITS

BAR BAR BAR BAR BAR BAR BAR

1200D 1201D 1202D 1204D 1206D 1208D 1210D

Series Number

Maximum Instantaneous Forward Voltage

RATINGS

SYMBOL

50

100

200

400

600

800

1000
VOLTS

60

120

240

480

Io

12

IFSM

250

720

960

1200

AMPS
0.90
1.05

0.95
1.10

@ IF = 3 Amps
@ IF = 12 Amps

VF

@ Tc = 25 oC

IR

0.5

TJ,TSTG

-65 to +175

VOLTS

BAR12d

K1

DIOTEC ELECTRONICS CORP.

Data Sheet No. BUDI-2500D-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.180"
Round
D
A

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Soft Glass
Passivation
G

Large die for high power capability

B
Silver Plated
Copper Slugs

Very low forward voltage drop

Silicon Die

Built-in stress relief mechanism for die protection

MILLIMETERS

Silver plated substrates for easy soldering or installation

DIM

MIN

MAX

MIN

MAX

5.36

5.56

0.211

0.219

1.98

2.18

0.078

0.086

4.72

4.93

0.186

0.194

Soldering temperature: 250 C maximum

Protects expensive automotive electronics and mobile

equipment

INCHES

F
G

0.76 Typ
1.02 Typ

0.030 Typ
0.040 Typ

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

Maximum Recurrent Peak Reverse Voltage

VRRM

Working Peak Reverse Voltage

VRWM

Maximum DC Blocking Voltage

VDC

Non-repetitive Peak Reverse Voltage

(Half wave, Single phase, 60Hz peak)

VRSM

Average Rectified Forward Current (Single phase, Resistive load,

60Hz)
Non-repetitive Peak Forward Surge Current
(Half wave, Single phase, 60Hz sine applied to rated load)

Maximum DC Reverse Current

At Rated DC Blocking Voltage
Operating & Storage Temperature Range

UNITS

BAR BAR BAR BAR BAR BAR BAR

2500D 2501D 2502D 2504D 2506D 2508D 2510D

Series Number

Maximum Instantaneous Forward Voltage

RATINGS

SYMBOL

50

100

200

400

600

800

1000
VOLTS

60

120

240

480

Io

25

IFSM

500

720

960

1200

AMPS
0.85
1.05

0.90
1.10

@ IF = 6 Amps
@ IF = 25 Amps

VF

@ Tc = 25 oC

IR

0.5

TJ,TSTG

-65 to +175

VOLTS

BAR25d

K3

DIOTEC ELECTRONICS CORP

Data Sheet No. BUDI-3500-1B

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Color Ring
Denotes Cathode

Die Size:
0.165" x 0.165"
Square

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Compact molded design

A
o

High surge current, 600 A @ TJ = 175 C

Low cost
Peak performance at elevated temperatures: 35 A
o
@ TJ = 175 C

MECHANICAL DATA
Case: Transfer molded plastic
MILLIMETERS

Finish: All external surfaces are silver plated for corrosion

resistance and superior solderability

DIM

Soldering Temperature: 250 oC maximum

Mounting Position: Any
Polarity: Color band denotes cathode

INCHES

MIN

MAX

MIN

MAX

9.78

10.29

0.385

0.405

5.97

6.35

0.235

0.250

5.46

5.71

0.215

0.225

4.19

4.45

0.165

0.175

5 NOM

5 NOM

Weight: 0.6 Ounces (1.8 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number
Maximum DC Blocking Voltage

VRRM

Maximum RMS Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

BAR
3500

BAR
3501

BAR
3502

BAR
3504

BAR
3506

BAR
3508

BAR
3510

50

100

200

400

600

800

1000

60

120

240

480

720

960

1200

VDC

Non-repetitive Peak Reverse Voltage (Half wave, single phase,

60 Hz peak)
Average Forward Rectified Current @ TC =150 oC

VRSM
IO

35

Peak Forward Surge Current (8.3mS single half sine wave

superimposed on rated load)

IFSM

600

Repetitive Peak Reverse Surge Current (Half wave, single phase,

60 Hz applied to rated load)

IRSM

110

Maximum Forward Voltage Drop at 35 Amp DC

VFM

1.1 (Typical 0.95)

1
50

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage

@ TA = 25 o C
@ TA = 100 oC

Maximum Thermal Resistance, Junction to Case (Note 1)

Junction Operating and Storage Temperature Range
Notes: 1) Single Side Cooled

UNITS

IRM

VOLTS

AMPS

1.2

VOLTS
A

RJC

0.9

C/W

TJ ,TSTG

-65 to +175

C
BAR35

K5

DIOTEC ELECTRONICS CORP

Data Sheet No. BUDI-3500S-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.165" x 0.165"
Square

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Color Ring
Denotes Cathode

D
A

Compact molded design

o

High surge current, 600 A @ TJ = 175 C

Low cost
Peak performance at elevated temperatures: 35 A
o
@ TJ = 175 C

MECHANICAL DATA
Case: Transfer molded plastic
MILLIMETERS

Finish: All external surfaces are corrosion resistant

and the contact areas are readily solderable

DIM

Soldering Temperature: 250 oC maximum

Mounting Position: Any
Polarity: Color band denotes cathode

INCHES

MIN

MAX

MIN

MAX

8.43

8.69

0.332

0.342

5.94

6.25

0.234

0.246

5.46

5.71

0.215

0.225

4.19

4.45

0.165

0.175

5 NOM

5 NOM

Weight: 0.6 Ounces (1.8 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

BAR BAR BAR BAR BAR BAR BAR

3500S 3501S 3502S 3504S 3506S 3508S 3510S

Series Number
Maximum DC Blocking Voltage

VRRM

Maximum RMS Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

50

100

200

400

600

800

1000

60

120

240

480

720

960

1200

VDC

Non-repetitive Peak Reverse Voltage (Half wave, single phase,

60 Hz peak)
Average Forward Rectified Current @ TC=150 oC

VRSM
IO

35

Peak Forward Surge Current (8.3mS single half sine wave

superimposed on rated load)

IFSM

600

Repetitive Peak Reverse Surge Current (Half wave, single phase,

60 Hz applied to rated load)

IRSM

110

Maximum Forward Voltage Drop at 35 Amp DC

VFM

1.1 (Typical 0.95)

1
50

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage

@ TA = 25 o C
@ TA = 100 oC

Maximum Thermal Resistance, Junction to Case (Note 1)

Junction Operating and Storage Temperature Range
Notes: 1) Single Side Cooled

UNITS

IRM

VOLTS

AMPS

1.2

VOLTS
A

RJC

0.9

C/W

TJ ,TSTG

-65 to +175

C
BAR35s

K7

DIOTEC ELECTRONICS CORP.

Data Sheet No. BUDI-3500D-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.165" x 0.165"
Square

D
A

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Soft Glass
Passivation
G

Large die for high power capability

B
Silver Plated
Copper Slugs

Very low forward voltage drop

Silicon Die

Built-in stress relief mechanism for die protection

MILLIMETERS

Silver plated substrates for easy soldering or installation

DIM
A

Soldering temperature: 250 C maximum

Protects expensive automotive electronics and mobile

equipment

INCHES

MIN

MAX

MIN

MAX

5.33

5.46

0.210

0.215

2.03

2.16

0.080

0.085

4.70

4.83

0.185

0.190

F
G

0.64
0.96

0.76
1.09

0.025
0.038

0.030
0.043

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

Maximum Recurrent Peak Reverse Voltage

VRRM

Working Peak Reverse Voltage

VRWM

Maximum DC Blocking Voltage

VDC

Average Rectified Forward Current (Single phase, Resistive load,

60Hz)
Non-repetitive Peak Forward Surge Current
(Half wave, Single phase, 60Hz sine applied to rated load)
Repetitive Peak Reverse Surge Current (Time constant = 10 mSec,
Duty cycle < 1.0%, Tc = 25 oC)
Maximum Instantaneous Forward Voltage
(IF = 80A @300 Sec pulse, Tc = 25o C)
Maximum DC Reverse Current
@ Tc = 25 oC
At Rated DC Blocking Voltage
@ Tc = 100 oC
Maximum Thermal Resistance, Junction to Lead (Note 1)
Operating & Storage Temperature Range
Notes: 1) Single Side Cooled

UNITS

BAR BAR BAR BAR BAR BAR BAR

3500D 3501D 3502D 3504D 3506D 3508D 3510D

Series Number

Non-repetitive Peak Reverse Voltage

(Half wave, Single phase, 60Hz peak)

RATINGS

SYMBOL

VRSM

50

100

200

400

600

800

1000
VOLTS

60

120

240

480

Io

35

IFSM

600

IRSM

110

720

960

1200

AMPS

VF

1.1 (1.05 Typical)

IR

0.5
50

RJC

0.9

C/W

TJ,TSTG

-65 to +175

1.2

VOLTS

C
BAR35d

K9

DIOTEC ELECTRONICS CORP

Data Sheet No. BUDI-5000-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.180" x 0.180"
Square

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Color Ring
Denotes Cathode

Compact molded design

A
o

High surge current, 720 A @ TJ = 175 C

Low cost
Peak performance at elevated temperatures: 50 A
o
@ TJ = 175 C

MECHANICAL DATA
Case: Transfer molded plastic
MILLIMETERS

Finish: All external surfaces are corrosion resistant

and the contact areas are readily solderable

DIM

Soldering Temperature: 250 oC maximum

Mounting Position: Any
Polarity: Color band denotes cathode

INCHES

MIN

MAX

MIN

MAX

9.78

10.29

0.385

0.405

6.05

6.20

0.238

0.244

5.54

6.60

0.218

0.220

4.19

4.45

0.165

0.175

5 NOM

5 NOM

Weight: 0.6 Ounces (1.8 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number
Maximum DC Blocking Voltage

VRRM

Maximum RMS Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

UNITS

BAR
5000

BAR
5001

BAR
5002

BAR
5004

BAR
5006

BAR
5008

BAR
5010

50

100

200

400

600

800

1000

60

120

240

480

720

960

1200

VDC

Non-repetitive Peak Reverse Voltage (Half wave, single phase,

60 Hz peak)
Average Forward Rectified Current @ TC=125 oC

VRSM

VOLTS

IO

50

Peak Forward Surge Current (8.3mS single half sine wave

superimposed on rated load)

IFSM

720

Repetitive Peak Reverse Surge Current (Half wave, single phase,

60 Hz applied to rated load)

IRSM

120

Maximum Forward Voltage Drop at 50 Amp DC

VFM

1.1 (Typical 0.95)

IRM

1
50

RJC

0.8

C/W

TJ ,TSTG

-65 to +175

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage

@ TA = 25 o C
@ TA = 100 oC

Maximum Thermal Resistance, Junction to Case (Note 1)

Junction Operating and Storage Temperature Range
Notes: 1) Single Side Cooled

AMPS

1.2

VOLTS

BAR50

K11

DIOTEC ELECTRONICS CORP

Data Sheet No. BUDI-5000S-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.180" x 0.180"
Square

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Color Ring
Denotes Cathode

D
A

Compact molded design

o

High surge current, 720 A @ TJ = 175 C

Low cost
Peak performance at elevated temperatures: 50 A
o
@ TJ = 175 C

MECHANICAL DATA
Case: Transfer molded plastic
MILLIMETERS

Finish: All external surfaces are corrosion resistant

and the contact areas are readily solderable

DIM

Soldering Temperature: 250 oC maximum

Mounting Position: Any
Polarity: Color band denotes cathode

INCHES

MIN

MAX

MIN

MAX

8.43

8.69

0.332

0.342

5.94

6.25

0.234

0.246

5.46

5.71

0.215

0.225

4.19

4.45

0.165

0.175

5 NOM

5 NOM

Weight: 0.6 Ounces (1.8 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

BAR BAR BAR BAR BAR BAR BAR

5000S 5001S 5002S 5004S 5006S 5008S 5010S

Series Number
Maximum DC Blocking Voltage

VRRM

Maximum RMS Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

50

100

200

400

600

800

1000

60

120

240

480

720

960

1200

VDC

Non-repetitive Peak Reverse Voltage (Half wave, single phase,

60 Hz peak)
Average Forward Rectified Current @ TC=125 oC

VRSM
IO

50

Peak Forward Surge Current (8.3mS single half sine wave

superimposed on rated load)

IFSM

720

Repetitive Peak Reverse Surge Current (Half wave, single phase,

60 Hz applied to rated load)

IRSM

120

Maximum Forward Voltage Drop at 100 Amp DC

VFM

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage

@ TA = 25 o C
@ TA = 100 oC

Maximum Thermal Resistance, Junction to Case (Note 1)

Junction Operating and Storage Temperature Range
Notes: 1) Single Side Cooled

UNITS

1.1 (Typical 1.05)

VOLTS

AMPS

1.2

VOLTS

1
50

RJC

0.8

C/W

TJ ,TSTG

-65 to +175

IRM

BAR50s

K13

DIOTEC ELECTRONICS CORP

Data Sheet No. BUDI-5000D-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.180" x 0.180"
Square

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

D
A
R

Soft Glass
Passivation
G

Large die for high power capability

B
Silver Plated
Copper Slugs

Very low forward voltage drop

Silicon Die

Built-in stress relief mechanism for die protection

MILLIMETERS

Silver plated substrates for easy soldering or installation

DIM

Soldering temperature: 250 oC maximum

Protects expensive automotive electronics and mobile

equipment

INCHES

MIN

MAX

MIN

MAX

7.25

7.35

0.285

0.290

2.05

2.15

0.080

0.085

6.50

6.60

0.256

0.260

0.72

0.82

0.028

0.032

0.96

1.07

0.038

0.042

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

Maximum DC Blocking Voltage

VRRM

Maximum RMS Voltage

VRWM

Non-repetitive Peak Reverse Voltage (Half wave, single phase,

60 Hz peak)
Average Forward Rectified Current @ TC=125 oC
Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Repetitive Peak Reverse Surge Current (Half wave, single phase,
60 Hz applied to rated load)
Maximum Instantaneous Forward Voltage Drop
(IF=100A @300 Sec Pulse, TC=25 OC)
@ TA = 25 o C
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
@ TA = 125 oC
Maximum Thermal Resistance, Junction to Case (Note 1)
Junction Operating and Storage Temperature Range
Notes: 1) Single Side Cooled

UNITS

BAR BAR BAR BAR BAR BAR BAR

5000D 5001D 5002D 5004D 5006D 5008D 5010D

Series Number

Maximum Peak Recurrent Reverse Voltage

RATINGS

SYMBOL

50

100

200

400

600

800

1000

60

120

240

480

720

960

1200

VDC
VRSM
IO

50

IFSM

720

IRSM

120

VOLTS

AMPS

1.2

VOLTS

VFM

1.1 (1.05 Typical)

IRM

2
50

RJC

0.8

C/W

TJ ,TSTG

-65 to +175

C
BAR59d

K15

DIOTEC ELECTRONICS CORP

Data Sheet No. BUDI-6000-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.216" Flat to Flat
Hex

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Color Ring
Denotes Cathode

Compact molded design

A
o

High surge current, 800 A @ TJ = 175 C

Low cost
Peak performance at elevated temperatures: 60 A
o
@ TJ = 150 C

MECHANICAL DATA
Case: Transfer molded plastic
MILLIMETERS

Finish: All external surfaces are corrosion resistant

and the contact areas are readily solderable

DIM

Soldering Temperature: 250 oC maximum

Mounting Position: Any
Polarity: Color band denotes cathode

MIN

INCHES

9.78

MAX
10.29

0.385

0.405

6.05

6.20

0.238

0.244

5.54

6.60

0.218

0.220

4.19

4.45

0.165

0.175

MIN

MAX

5 NOM

5 NOM

Weight: 0.6 Ounces (1.8 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

Series Number
Maximum DC Blocking Voltage

VRRM

Maximum RMS Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

Non-repetitive Peak Reverse Voltage (Half wave, single phase,
60 Hz peak)
Average Forward Rectified Current @ TC=125 oC
Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Repetitive Peak Reverse Surge Current (Half wave, single phase,
60 Hz applied to rated load)
Maximum Instantaneous Forward Voltage Drop
(IF=100A @300 Sec Pulse, TC=25 OC)
@ TA = 25 o C
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
@ TA = 125 oC
Maximum Thermal Resistance, Junction to Case (Note 1)
Junction Operating and Storage Temperature Range
Notes: 1) Single Side Cooled

RATINGS

SYMBOL

UNITS

BAR
6000

BAR
6001

BAR
6002

BAR
6004

BAR
6006

BAR
6008

BAR
6010

50

100

200

400

600

800

1000

60

120

240

480

720

960

1200

VDC
VRSM

VOLTS

IO

60

IFSM

800

IRSM

140

VFM

1.06 (1.03 Typical)

IRM

1
50

RJC

0.8

C/W

TJ ,TSTG

-65 to +175

AMPS

1.10

VOLTS

BAR60

K17

DIOTEC ELECTRONICS CORP

Data Sheet No. BUDI-6000-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.216" Flat to Flat
Hex

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Color Ring
Denotes Cathode

Compact molded design

High surge current, 800 A @ TJ = 175 C

Low cost
Peak performance at elevated temperatures: 60 A
o
@ TJ = 150 C

MECHANICAL DATA
Case: Transfer molded plastic
MILLIMETERS

Finish: All external surfaces are corrosion resistant

and the contact areas are readily solderable

DIM

Soldering Temperature: 250 C maximum

Mounting Position: Any
Polarity: Color band denotes cathode

INCHES

MIN

MAX

MIN

MAX

8.43

8.69

0.332

0.342

5.94

6.25

0.234

0.246

5.46

5.71

0.215

0.225

4.19

4.45

0.165

0.175

5 NOM

5 NOM

Weight: 0.6 Ounces (1.8 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

Maximum DC Blocking Voltage

VRRM

Maximum RMS Voltage

VRWM

Non-repetitive Peak Reverse Voltage (Half wave, single phase,

60 Hz peak)
Average Forward Rectified Current @ TC=125 oC
Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Repetitive Peak Reverse Surge Current (Half wave, single phase,
60 Hz applied to rated load)
Maximum Instantaneous Forward Voltage Drop
(IF=100A @300 Sec Pulse, TC=25 OC)
@ TA = 25 o C
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
@ TA = 125 oC
Maximum Thermal Resistance, Junction to Case (Note 1)
Junction Operating and Storage Temperature Range
Notes: 1) Single Side Cooled

UNITS

BAR BAR BAR BAR BAR BAR BAR

6000S 6001S 6002S 6004S 6006S 6008S 6010S

Series Number

Maximum Peak Recurrent Reverse Voltage

RATINGS

SYMBOL

50

100

200

400

600

800

1000

60

120

240

480

720

960

1200

VDC
VRSM

VOLTS

IO

60

IFSM

800

IRSM

140

VFM

1.06 (1.03 Typical)

IRM

1
50

RJC

0.8

C/W

TJ ,TSTG

-65 to +175

AMPS

1.10

VOLTS

BAR60s

K19

DIOTEC ELECTRONICS CORP

Data Sheet No. BUDI-6000-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.216" Flat to Flat
Hex

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Color Ring
Denotes Cathode

Compact molded design

High surge current, 800 A @ TJ = 175 C

Low cost
Peak performance at elevated temperatures: 60 A
o
@ TJ = 150 C

MECHANICAL DATA
Case: Transfer molded plastic
MILLIMETERS

Finish: All external surfaces are corrosion resistant

and the contact areas are readily solderable

DIM

Soldering Temperature: 250 C maximum

Mounting Position: Any
Polarity: Color band denotes cathode

INCHES

MIN

MAX

MIN

MAX

8.43

8.69

0.332

0.342

5.94

6.25

0.234

0.246

5.46

5.71

0.215

0.225

4.19

4.45

0.165

0.175

5 NOM

5 NOM

Weight: 0.6 Ounces (1.8 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

Maximum DC Blocking Voltage

VRRM

Maximum RMS Voltage

VRWM

Non-repetitive Peak Reverse Voltage (Half wave, single phase,

60 Hz peak)
Average Forward Rectified Current @ TC=125 oC
Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Repetitive Peak Reverse Surge Current (Half wave, single phase,
60 Hz applied to rated load)
Maximum Instantaneous Forward Voltage Drop
(IF=100A @300 Sec Pulse, TC=25 OC)
@ TA = 25 o C
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
@ TA = 125 oC
Maximum Thermal Resistance, Junction to Case (Note 1)
Junction Operating and Storage Temperature Range
Notes: 1) Single Side Cooled

UNITS

BAR BAR BAR BAR BAR BAR BAR

6000S 6001S 6002S 6004S 6006S 6008S 6010S

Series Number

Maximum Peak Recurrent Reverse Voltage

RATINGS

SYMBOL

50

100

200

400

600

800

1000

60

120

240

480

720

960

1200

VDC
VRSM

VOLTS

IO

60

IFSM

800

IRSM

140

VFM

1.06 (1.03 Typical)

IRM

1
50

RJC

0.8

C/W

TJ ,TSTG

-65 to +175

AMPS

1.10

VOLTS

BAR60s

K19

DIOTEC ELECTRONICS CORP

Data Sheet No. BUDI-7500-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.250" Diameter
Round

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Color Ring
Denotes Cathode

Compact molded design

A
o

High surge current, 800 A @ TJ = 175 C

Low cost
Peak performance at elevated temperatures: 75 A
o
@ TJ = 150 C

MECHANICAL DATA
Case: Transfer molded plastic
MILLIMETERS

Finish: All external surfaces are corrosion resistant

and the contact areas are readily solderable

DIM

Soldering Temperature: 250 oC maximum

Mounting Position: Any
Polarity: Color band denotes cathode

INCHES

MIN

MAX

MIN

MAX

9.78

10.29

0.385

0.405

6.05

6.20

0.238

0.244

5.54

6.60

0.218

0.220

4.19

4.45

0.165

0.175

5 NOM

5 NOM

Weight: 0.6 Ounces (1.8 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

Series Number
Maximum DC Blocking Voltage

VRRM

Maximum RMS Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

UNITS

BAR
7500

BAR
7501

BAR
7502

BAR
7504

BAR
7506

BAR
7508

BAR
7510

50

100

200

400

600

800

1000

60

120

240

480

720

960

1200

VDC

Non-repetitive Peak Reverse Voltage (Half wave, single phase,

60 Hz peak)
Average Forward Rectified Current @ TC=150 oC

VRSM

VOLTS

IO

75

Peak Forward Surge Current (8.3mS single half sine wave

superimposed on rated load)

IFSM

800

Repetitive Peak Reverse Surge Current (Half wave, single phase,

60 Hz applied to rated load)

IRSM

140

Maximum Forward Voltage Drop at 100 Amp DC

VFM

1.05 (Typical <1.0)

IRM

1
50

RJC

0.8

C/W

TJ ,TSTG

-65 to +175

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage

@ TA = 25 o C
@ TA = 100 oC

Maximum Thermal Resistance, Junction to Case (Note 1)

Junction Operating and Storage Temperature Range
Notes: 1) Single Side Cooled

AMPS

1.1

VOLTS

BAR75

K23

DIOTEC ELECTRONICS CORP

Data Sheet No. BUDI-7500S-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.250" Diameter
Round

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

Color Ring
Denotes Cathode

D
A

Compact molded design

o

High surge current, 800 A @ TJ = 175 C

Low cost
Peak performance at elevated temperatures: 75 A
o
@ TJ = 150 C

MECHANICAL DATA
Case: Transfer molded plastic
MILLIMETERS

Finish: All external surfaces are corrosion resistant

and the contact areas are readily solderable

DIM

Soldering Temperature: 250 oC maximum

Mounting Position: Any
Polarity: Color band denotes cathode

INCHES

MIN

MAX

MIN

MAX

8.43

8.69

0.332

0.342

5.94

6.25

0.234

0.246

5.46

5.71

0.215

0.225

4.19

4.45

0.165

0.175

5 NOM

5 NOM

Weight: 0.6 Ounces (1.8 Grams)

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

RATINGS

SYMBOL

UNITS

BAR BAR BAR BAR BAR BAR BAR

7500S 7501S 7502S 7504S 7506S 7508S 7510S

Series Number
Maximum DC Blocking Voltage

VRRM

Maximum RMS Voltage

VRWM

Maximum Peak Recurrent Reverse Voltage

50

100

200

400

600

800

1000

60

120

240

480

720

960

1200

VDC

Non-repetitive Peak Reverse Voltage (Half wave, single phase,

60 Hz peak)
Average Forward Rectified Current @ TC=150 oC

VRSM

VOLTS

IO

75

Peak Forward Surge Current (8.3mS single half sine wave

superimposed on rated load)

IFSM

800

Repetitive Peak Reverse Surge Current (Half wave, single phase,

60 Hz applied to rated load)

IRSM

140

Maximum Forward Voltage Drop at 100 Amp DC

VFM

1.05 (Typical < 1.0)

IRM

1
50

RJC

0.8

C/W

TJ ,TSTG

-65 to +175

Maximum Average DC Reverse Current

At Rated DC Blocking Voltage

@ TA = 25 o C
@ TA = 100 oC

Maximum Thermal Resistance, Junction to Case (Note 1)

Junction Operating and Storage Temperature Range
Notes: 1) Single Side Cooled

AMPS

1.1

VOLTS

BAR75s

K25

DIOTEC ELECTRONICS CORP

Data Sheet No. BUDI-7500D-1A

18020 Hobart Blvd., Unit B

Gardena, CA 90248 U.S.A
Tel.: (310) 767-1052 Fax: (310) 767-7958

MECHANICAL SPECIFICATION

FEATURES
R

PROPRIETARY SOFT GLASS JUNCTION

PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE

Die Size:
0.250" Diameter
Round die

VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM

MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)

D
A
R

Soft Glass
Passivation
G

Large die for high power capability

B
Silver Plated
Copper Slugs

Very low forward voltage drop

Silicon Die

Built-in stress relief mechanism for die protection

MILLIMETERS

Silver plated substrates for easy soldering or installation

DIM

Soldering temperature: 250 oC maximum

Protects expensive automotive electronics and mobile

equipment

INCHES

MIN

MAX

MIN

MAX

7.25

7.35

0.285

0.290

2.05

2.15

0.080

0.085

6.50

6.60

0.256

0.260

0.72

0.82

0.028

0.032

0.96

1.07

0.038

0.042

MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS

Ratings at 25 C ambient temperature unless otherwise specified.

PARAMETER (TEST CONDITIONS)

Maximum DC Blocking Voltage

VRRM

Maximum RMS Voltage

VRWM

Non-repetitive Peak Reverse Voltage (Half wave, single phase,

60 Hz peak)
Average Forward Rectified Current @ TC=125 oC
Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Repetitive Peak Reverse Surge Current (Half wave, single phase,
60 Hz applied to rated load)
Maximum Instantaneous Forward Voltage Drop
(IF=100A @300 Sec Pulse, TC=25 OC)
@ TA = 25 o C
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
@ TA = 125 oC
Maximum Thermal Resistance, Junction to Case (Note 1)
Junction Operating and Storage Temperature Range
Notes: 1) Single Side Cooled

UNITS

BAR BAR BAR BAR BAR BAR BAR

7500D 7501D 7502D 7504D 7506D 7508D 7510D

Series Number

Maximum Peak Recurrent Reverse Voltage

RATINGS

SYMBOL

50

100

200

400

600

800

1000

60

120

240

480

720

960

1200

VDC
VRSM

VOLTS

IO

75

IFSM

800

IRSM

140

VFM

1.05 (1.00 Typical)

IRM

2
50

RJC

0.8

C/W

TJ ,TSTG

-65 to +175

AMPS

1.10

VOLTS

BAR75d

K27

APPENDICES

PACKAGING INFORMATION
CROSS REFERENCES
ACRONYMS, ABBREVIATIONS, AND SYMBOLS
ALPHA-NUMERIC PRODUCT INDEX
SAMPLE REQUEST FORM
SOFT GLASS DIODE

DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

TAPE AND REEL PACKAGING (AXIAL LEAD DIODES)

DIODE
PACKAGE
DO-41/DT-41
DO-15/DT-15
DO-27/DT-27
G-6

COMPONENT
SPACING
FIG 1. "A"
Inches (mm)
0.200 ( 5)
0.200 ( 5)
0.395 (10)
0.395 (10)

TAPE
SPACING
FIG 1. "B"
Inches (mm)
0.395 (10)
0.395 (10)
0.395 (10)
0.395 (10)

REEL
DIAMETER
FIG 2. "C"
Inches (mm)
12.82 (326)
12.82 (326)
12.82 (326)
12.82 (326)

QUANITY
PER REEL

PER CARTON

5,000
3,500
1,250
600

20,000
14,000
5,000
2,400

0.25" (6.35mm)

CARTON
DIMENSIONS
Inches (mm)

14 x 14 x 14 (355 x 355 x 355)

CARTON
GROSS
WEIGHT
Lbs (Kgs
22.0 (10.5)
19.0 ( 8.5)
21.0 ( 9.4)
16.5 ( 7.5)

2.75" (70mm)

0.625" (16mm)
Dia.
A

3.25" (82.6mm)

B
C
FIGURE 1

FIGURE 2

FIGURE 3

BULK PACKAGING
AXIAL LEAD DIODES
PACKAGE
DO-41/DT-41
DO-15/DT-15
DO-27/DT-27
G-6

BOX SIZE
Inches
7.88 x 3.31 x.0.94
7.88 x 3.31 x.0.94
12.00 x 3.00 x.1.56
12.00 x 3.00 x.1.56

CARTON SIZE
Inches
17.25 x 8.75 x.10.00
17.25 x 8.75 x.10.00
16.50 x 12.25 x.11.25
16.50 x 12.25 x.11.25

PER BOX
1,000
1,500
500
400

QUANTITY
PER CARTON
40,000
40,000
15,000
12,000

GROSS WEIGHT, Lbs (Kgs)

PER BOX
PER CARTON
0.825 (0.37)
43.0 (19.5)
1.030 (0.48)
43.0 (19.5)
1.438 (0.65)
44.0 (20.0)
1.500 (0.68)
44.0 (20.0)

BRIDGE RECTIFIERS
WB
SB2
KBL
SB4
SB5
SBU6
DB6
DB8
DB25/T
DB25/W
DB25P/T
DB25P/W
SDB

12.00 x 4.25 x.3.75

8.50 x 8.50 x.2.12
12.50 x 6.50 x.0.50
12.50 x 6.50 x.0.50
9.50 x 5.50 x.2.50
12.50 x 6.50 x.0.50
7.62 x 7.62 x.1.56
9.00 x 9.00 x.1.90
7.62 x 7.62 x.1.56
7.62 x 7.62 x.1.56
7.62 x 7.62 x.1.56
7.62 x 7.62 x.1.56
7.62 x 7.62 x.1.56

20.0 x 10.0 x.10.0

17.0 x 9.0 x.10.0
13.5 x 13.5 x. 8.0
13.5 x 13.5 x. 8.0
17.0 x 9.0 x.10.0
13.5 x 13.5 x. 8.0
13.5 x 13.5 x.14.0
17.0 x 9.0 x.10.0
17.0 x 9.0 x.10.0
17.0 x 9.0 x.10.0
17.0 x 9.0 x.10.0
17.0 x 9.0 x.10.0
17.0 x 9.0 x.10.0

1,000
400
50 (Tray)
54 (Tray)
100
50 (Tray)
200
50
50
50
50
50
72

10,000
4,000
2,000
2,160
1,000
2,000
2,000
500
500
500
500
500
720

2.50 (1.14)
2.80 (1.40)
5.12 (2.35)
2.87 (1.30)
3.00 (1.36)
2.87 (1.30)
2.96 (1.48)
2.10 (0.96)
4.00 (1.82)
4.00 (1.82)
2.70 (1.23)
2.50 (1.14)
3.90 (1.77)

25.0 (11.4)
28.0 (15.0)
39.6 (18.0)
39.6 (18.0)
30.0 (13.6)
39.6 (18.0)
29.6 (14.8)
21.0 ( 9.6)
40.0 (18.2)
40.0 (18.2)
27.0 (12.3)
25.0 (11.4)
39.0 (17.7)

ANTI-STATIC TUBE PACKAGING

PACKAGE
DI (BRIDGE)
SINB (BRIDGE)
TO-220AB
TO-220AC
TO-247 AB
TO-247 AC

BOX SIZE
Length - Inches
19.2
19.2
20.5
20.5
16.0
16.0

CARTON SIZE
Inches
24 x 6 x 6
24 x 6 x 6
24 x 6 x 6
24 x 6 x 6
24 x 6 x 6
24 x 6 x 6

QUANTITY
PER TUBE
PER CARTON
50
2,500
50
2,500
50
2,500
50
2,500
25
1,250
25
1,250

GROSS WEIGHT, Lbs (Kgs)

PER TUBE
PER CARTON
0.28 (0.13)
14.1 (6.4)
0.28 (0.13)
14.1 (6.4)
0.28 (0.13)
14.1 (6.4)
0.28 (0.13)
14.1 (6.4)
0.41 (0.19)
20.5 (9.5)
0.41 (0.19)
20.5 (9.5)

VIII-1
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

SUGGESTED
DIOTEC
PAGE
REPLACEMENT NO.
PART NO.
1N5817
1N5817
A1
1N5818
1N5818
A1
1N5819
1N5819
A1
1N5820
1N5820
A5
1N5821
1N5821
A5
1N5822
1N5822
A5
1N5823
SK502
A9
1N5824
SK504
A9
1N5825
SK504
A9
MBR1035
12SK40
A13
MBR1045
12SK50
A13
MBR1050
12SK50
A13
MBR1060
12SK60
A13
MBR1090
12SK100
A13
MBR10100
12SK100
A13
MBR150
SK106
A3
MBR1535CT SK1640C
B3
MBR1540CT SK1640C
B3
MBR1545CT SK1650C
B3
MBR1550CT SK1650C
B3
MBR1560CT SK1660C
B3
MBR160
SK106
A3
MBR1635
12SK40
A13
MBR1645
12SK40
A13
MBR1650
12SK50
A13
MBR1660
12SK60
A13
MBR2035CT SK1640C
B3
MBR2045CT SK1650C
B3
MBR2050CT SK1650C
B3
MBR2060CT SK1660C
B3
MBR2090CT SK16100C
B3
MBR20100CT SK16100C
B3
MBR2535CT SK2440C
B5
MBR2545CT SK2450C
B5
MBR2550CT SK2450C
B5
MBR2560CT SK2460C
B5
MBR3035PT SK3040C
B7
MBR3045PT SK3050C
B7
MBR3050PT SK3050C
B7
MBR3060PT SK3060C
B7
MBR320
SK302
A7
MBR330
SK304
A7
MBR340
SK304
A7
MBR350
SK306
A7
MBR360
SK306
A7
MBR4035PT SK4040C
B7
MBR4045PT SK4050C
B7
MBR4050PT SK4050C
B7
MBR4060PT SK4060C
B7
MBR735
12SK40
A13
MBR745
12SK50
A13
MBR750
12SK50
A13
MBR760
12SK60
A13
MBRF1035
12SK40
A13
MBRF1045
12SK50
A13
MBRF1050
12SK50
A13
MBRF1060
12SK60
A13
MBR2050CT SK1650C
B3
MBR2060CT SK1660C
B3
NST520
6SK40
A11
NST530
6SK40
A11
INDUSTRY
PART NO.

SUGGESTED
INDUSTRY
DIOTEC
PAGE
PART NO. REPLACEMENT NO.
PART NO.
NST545
6SK50
A11
NST1020
12SK40
A13
NST1030
12SK40
A13
NST1045
12SK50
A13
NST1625
16SK40
A15
NST1635
16SK40
A15
NST1645
16SK50
A15
NST2025
16SK50
A15
NST2035
16SK50
A15
NST2045
16SK50
A15
NST2525
SK2440C
B5
NST2535
SK2440C
B5
NST3020
SK1640C
B3
NST3030
SK1640C
B3
NST3045
SK1650C
B3
SB020
SK102
A3
SB030
SK104
A3
SB040
SK104
A3
SB120
SK102
A3
SB130
SK104
A3
SB140
SK104
A3
SB150
SK106
A3
SB160
SK106
A3
SB170
SK108
A3
SB180
SK108
A3
SB190
SK110
A3
SB1100
SK110
A3
SB320
SK302
A7
SB330
SK304
A7
SB340
SK304
A7
SB350
SK306
A7
SB360
SK306
A7
SB380
SK310
A7
SB3100
SK310
A7
SB520
SK502
A9
SB530
SK504
A9
SB540
SK504
A9
SB550
SK506
A9
SB560
SK506
A9
SB590
SK510
A9
SB5100
SK510
A9
SBL1030CT SK1240C
B1
SBL1040CT SK1240C
B1
SBL1630CT SK1640C
B3
SBL1640CT SK1640C
B3
SBL530
6SK40
A11
SBL530CT SK1240C
B1
SBL540
6SK40
A11
SBL540CT SK1240C
B1
SBLF1030 12SK40
A13
SBLF1040 12SK40
A13
SBLF1630CTSK1640C
B3
SBLF1640CTSK1640C
B3
SD241P
SK3050C
B7
SD115
SK102
A3
SD120
SK104
A3
SD130
SK104
A3
SD140
SK106
A3
SD150
SK106
A3
SD160
SK108
A3
SD170
SK108
A3

SUGGESTED
INDUSTRY
DIOTEC
PAGE
PART NO. REPLACEMENT NO.
PART NO.
SD180
SK108
A3
SD315
SK302
A7
SD320
SK302
A7
SD330
SK304
A7
SD340
SK304
A7
SD350
SK306
A7
SD360
SK306
A7
SD380
SK310
A7
SD520
SK502
A9
SD530
SK504
A9
SD540
SK504
A9
SDS1620L 16SK40
A15
SDS1630L 16SK40
A15
SDS1640L 16SK40
A15
SDS1645L 16SK50
A15
SR102
SK102
A3
SR103
SK104
A3
SR104
SK104
A3
SR105
SK106
A3
SR106
SK106
A3
SR302
SK302
A7
SR303
SK304
A7
SR304
SK304
A7
SR305
SK306
A7
SR306
SK306
A7
SR502
SK502
A9
SR503
SK504
A9
SR504
SK504
A9
SR505
SK506
A9
SR506
SK506
A9
SR802
12SK40
A13
SR803
12SK40
A13
SR804
12SK40
A13
SR805
12SK50
A13
SR806
12SK60
A13
SR1002
12SK40
A13
SR1003
12SK40
A13
SR1004
12SK40
A13
SR1005
12SK50
A13
SR1006
12SK60
A13
SR1602
SK1640C
B3
SR1603
SK1640C
B3
SR1604
SK1640C
B3
SR1605
SK1650C
B3
SR1606
SK1660C
B3
SR2020
SK2440C
B5
SR2030
SK2440C
B5
SR2045
SK2450C
B5
SR3030
SK3040C
B7
SR3040
SK3040C
B7
SR3045
SK3050C
B7
SR3050
SK3050C
B7
SR3060
SK3060C
B7
SR4020
SK4040C
B9
SR4030
SK4040C
B9
SR4040
SK4040C
B9
SR4050
SK4040C
B9
SR5020
SK4040C
B9
SR5030
SK4040C
B9
SR5040
SK4040C
B9
SR5050
SK4050C
B9

SUGGESTED
INDUSTRY
DIOTEC
PAGE
PART NO. REPLACEMENT NO.
PART NO.
USD320C SK3040C
B9
USD335C SK3040C
B9
USD345C SK3050C
B9
USD620
6SK40
A11
USD620C SK1240C
B1
USD635
6SK40
A11
USD635C SK1240C
B1
USD640
6SK40
A11
USD640C SK1240C
B1
USD645
6SK50
A11
USD645C SK1250C
B1
USD720
12SK40
A13
USD720C SK1640C
B3
USD735
12SK40
A13
USD735C SK1640C
B3
USD740
12SK40
A13
USD740C SK1640C
B3
USD745
12SK50
A13
USD745C SK1650C
B3
USD820
12SK40
A13
USD830
12SK40
A13
USD835
12SK40
A13
USD840
12SK40
A13
USD845
12SK50
A13
USD920
16SK40
A15
USD935
16SK40
A15
USD940
16SK40
A15
USD945
16SK50
A15
VSK1020
12SK40
A13
VSK1035
12SK40
A13
VSK1045
12SK50
A13
VSK12
SK1240C
B1
VSK13
SK1240C
B1
VSK14
SK1240C
B1
VSK120
SK102
A3
VSK130
SK104
A3
VSK140
SK104
A3
VSK2020
SK1640C
B3
VSK2035
SK1640C
B3
VSK2045
SK1650C
B3
VSK2420
SK2440C
B5
VSK2435
SK2440C
B5
VSK2445
SK2450C
B5
VSK320
SK302
A7
VSK330
SK304
A7
VSK340
SK304
A7
VSK520
SK502
A9
VSK530
SK504
A9
VSK540
SK504
A9
VSK62
6SK40
A11
VSK63
6SK40
A11
VSK64
6SK40
A11
VSK920
16SK40
A15
VSK935
16SK40
A15
VSK945
16SK50
A15

II-1
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

DIODE CROSS REFERENCE

SUGGESTED
DIOTEC
PAGE
REPLACEMENT NO.
PART NO.
BYT01-200
SPR12
C1
BYT01-300
SPR13
C1
BYT01-400
UFR104
C3
BYT03-200
SPR32
C7
BYT03-300
SPR33
C7
BYT03-400
SPR34
C7
BYT08P-200A SPR82
C21
BYT08P-300A SPR83
C21
BYT08P-400A SPR84
C21
BYT08PI-200 8SPR02
C19
BYT08PI-300 8SPR03
C19
BYT08PI-400 8SPR04
C19
BYT12P-600A SPR156
C25
BYT30P-200
CALL
BYT30P-300
CALL
BYT30P-400
CALL
BYV27-100
SPR21
C5
BYV27-150
SPR22
C5
BYV27-200
SPR22
C5
BYV27-50
SPR21
C5
BYV28-100
SPR51
C13
BYV28-150
SPR52
C13
BYW100-100 SPR21
C5
BYW100-150 SPR22
C5
BYW100-200 SPR22
C5
BYW100-50
SPR21
C5
BYW29-100
SPR81
C21
BYW29-100A SPR81
C21
BYW29-150
SPR82
C21
BYW29-150A SPR82
C21
BYW29-200
SPR82
C21
BYW29-200A SPR82
C21
BYW29-50
SPR81
C21
BYW29-50A
SPR81
C21
BYW51-50A
SPR161C
D7
BYW51-100A SPR161C
D7
BYW51-150A SPR162C
D7
BYW51-200A SPR162C
D7
BYW77P-50
CALL
BYW77P-100 CALL
BYW77P-150 CALL
BYW77P-200 CALL
BYW80-50A
8SPR01
C19
BYW80-100A 8SPR01
C19
BYW80-150A 8SPR02
C19
BYW80-200A 8SPR02
C19
BYW81P-50A SPR150
C25
BYW81P-100A SPR151
C25
BYW81P-150A SPR152
C25
BYW81P-200A SPR152
C25
BYW98-50
SPR31
C7
BYW98-100
SPR31
C7
BYW98-150
SPR32
C7
BYW98-200
SPR32
C7
BYW99P-50
UFR3001C
D9
BYW99P-100 UFR3001C
D9
BYW99P-150 UFR3002C
D9
BYW99P-200 UFR3002C
D9
EGP10A
UFR101
C3
EGP10B
UFR102
C3
EGP10C
UFR102
C3
INDUSTRY
PART NO.

SUGGESTED
INDUSTRY
DIOTEC
PART NO. REPLACEMENT
PART NO.
EGP10D
UFR102
EGP10F
UFR103
EGP10G
UFR104
EGP10J
UFR106
EGP10K
UFR108
EGP10M
UFR110
EGP20A
SPR21
EGP20B
SPR21
EGP20C
SPR22
EGP20D
SPR22
EGP20F
SPR23
EGP20G
UFR24
EGP20J
UFR26
EGP20K
UFR28
EGP30A
SPR31
EGP30B
SPR31
EGP30C
SPR32
EGP30D
SPR32
EGP30F
SPR33
EGP30G
SPR34
EGP30J
UFR306
EGP30K
UFR308
EGP50A
SPR51
EGP50B
SPR51
EGP50C
SPR52
EGP50D
SPR52
EGP50F
SPR53
EGP50G
SPR54
ER1001
UFR100
ER1002
UFR101
ER1003
UFR102
ER1004
UFR104
ER1005
UFR106
ER1006
UFR108
FE1A
SPR11
FE1B
SPR11
FE1C
SPR12
FE1D
SPR12
FE2A
SPR21
FE2B
SPR21
FE2C
SPR22
FE2D
SPR22
FE3A
SPR31
FE3B
SPR31
FE3C
SPR32
FE3D
SPR32
FE5A
SPR51
FE5B
SPR51
FE5C
SPR52
FE5D
SPR52
FE6A
SPR51
FE6B
SPR51
FE6C
SPR52
FE6D
SPR52
FEP16AT
SPR161C
FEP16BT
SPR161C
FEP16CT
SPR162C
FEP16DT
SPR162C
FEP16FT
SPR163C
FEP16GT SPR164C
FEP16JT
SPR166C

PAGE
NO.
C3
C3
C3
C3
C3
C3
C5
C5
C5
C5
C5
C5
C5
C5
C7
C7
C7
C7
C7
C7
C9
C9
C13
C13
C13
C13
C13
C13
C3
C3
C3
C3
C3
C3
C1
C1
C1
C1
C5
C5
C5
C5
C7
C7
C7
C7
C13
C13
C13
C13
C13
C13
C13
C13
D7
D7
D7
D7
D7
D7
D7

SUGGESTED
INDUSTRY
DIOTEC
PART NO. REPLACEMENT
PART NO.
FEP16HT
SPR165C
FEPF16AT SPR1601C
FEPF16BT SPR1601C
FEPF16CT SPR1602C
FEPF16DT SPR1602C
FEPF16FT SPR1603C
FEPF16GT SPR1604C
FEPF16HT SPR1605C
FEP30AP
UFR3001C
FEP30BP
UFR3001C
FEP30CP
UFR3002C
FEP30DP
UFR3002C
FEP30FP
UFR3003C
FEP30GP UFR3004C
FEP30HP
UFR3005C
FES16AT
SPR150
FES16BT
SPR151
FES16CT
SPR152
FES16DT
SPR152
FES16FT
SPR153
FES16GT SPR154
FES16HT
SPR155
FES16JT
SPR156
FES8AT
SPR80
FES8BT
SPR81
FES8CT
SPR82
FES8DT
SPR82
FES8FT
SPR83
FES8GT
SPR84
FES8HT
SPR85
FES8JT
SPR86
FESF8AT
8SPR01
FESF8BT
8SPR01
FESF8CT 8SPR02
FESF8DT 8SPR02
FESF8FT
8SPR03
FESF8GT 8SPR04
FESF8HT 8SPR05
GI1001
SPR11
GI1002
SPR11
GI1003
SPR12
GI1004
SPR12
GI1101
SPR21
GI1102
SPR21
GI1103
SPR22
GI1104
SPR22
GI1301
SPR51
GI1302
SPR51
GI1303
SPR52
GI1304
SPR52
GI1401
SPR80
GI1402
SPR81
GI1403
SPR82
GI1404
SPR82
GI2401
SPR1601C
GI2402
SPR1601C
GI2403
SPR1602C
GI2404
SPR1602C
HER101
UFR100
HER102
UFR101
HER103
UFR102

PAGE
NO.
D7
D5
D5
D5
D5
D5
D5
D5
D9
D9
D9
D9
D9
D9
D9
C25
C25
C25
C25
C25
C25
C25
C25
C21
C21
C21
C21
C21
C21
C21
C21
C19
C19
C19
C19
C19
C19
C19
C1
C1
C1
C1
C5
C5
C5
C5
C13
C13
C13
C13
C21
C21
C21
C21
D5
D5
D5
D5
C3
C3
C3

SUGGESTED
INDUSTRY
DIOTEC
PART NO. REPLACEMENT
PART NO.
HER104
UFR103
HER105
UFR104
HER106
UFR106
HER151
SPR21
HER152
SPR21
HER153
SPR22
HER154
SPR23
HER155
UFR24
HER156
UFR26
HER301
UFR300
HER302
UFR301
HER303
UFR302
HER304
UFR303
HER305
UFR304
HER601
UFR600
HER602
UFR601
HER603
UFR602
HER604
UFR603
HER605
UFR604
HER801
SPR81
HER802
SPR81
HER803
SPR82
HER804
SPR83
HER805
SPR84
HER806
SPR85
HER1601
SPR161C
HER1602
SPR161C
HER1603
SPR162C
HER1604
SPR163C
HER1605
SPR164C
HER3001
UFR3001C
HER3002
UFR3001C
HER3003
UFR3002C
HER3004
UFR3003C
HER3005
UFR3004C
HER3006
UFR3005C
MUR105
SPR11
MUR110
SPR11
MUR115
SPR12
MUR120
SPR12
MUR130
SPR13
MUR140
UFR104
MUR150
UFR106
MUR160
UFR106
MUR170
UFR108
MUR180
UFR108
MUR405
SPR51
MUR410
SPR51
MUR415
SPR52
MUR420
SPR52
MUR430
SPR53
MUR440
SPR54
MUR605CT SPR601C
MUR610CT SPR601C
MUR615CT SPR602C
MUR620CT SPR602C
MUR805
SPR81
MUR810
SPR81
MUR815
SPR82
MUR820
SPR82
MUR830
SPR83

III-1
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

DIODE CROSS REFERENCE (Cont'd)

INDUSTRY
PART NO.
MUR840
MUR850
MUR860
MUR1505
MUR1510
MUR1515
MUR1520
MUR1530
MUR1540
MUR1550
MUR1560
MUR1605CT
MUR1610CT
MUR1615CT
MUR1620CT
MUR1630CT
MUR1640CT
MUR1650CT
MUR3005PT
MUR3010PT
MUR3015PT
MUR3020PT
MUR3030PT
MUR3040PT
R710XPT
R711XPT
R712XPT
R714XPT
SDF10U40DN
SDF15U20DN
SDF15U40DN
SDF20U20DN
SDF20U40DN
SDF30U20DN
SDF30U60DN
SDP04U40DN
SDP05U60DN
SDP06U20DN
SDP06U40DN
SDP10U20DN
SDP10U60DN
SDP15U20DN
SDS04U40S
SDS05U60S
SDS06U20DN
SDS06U20S
SDS06U40S
SDS10U20DN
SDS10U20S
SDS10U40S
SDS10U60S
SDS16U20DN
SET801
SET802
SET803
SET804
SET5401
SET5402
SET5403
SET5404
SF11

SUGGESTED
DIOTEC
REPLACEMENT
PART NO.
SPR84
SPR85
SPR86
SPR150
SPR151
SPR152
SPR152
SPR153
SPR154
SPR155
SPR156
SPR1601C
SPR1601C
SPR1602C
SPR1602C
SPR1603C
SPR1604C
SPR1605C
UFR3001C
UFR3001C
UFR3002C
UFR3002C
UFR3003C
UFR3004C
UFR3001C
UFR3001C
UFR3002C
UFR3004C
UFR3004C
UFR3002C
UFR3004C
UFR3002C
UFR3004C
UFR3002C
UFR3004C
SPR84
SPR86
SPR82
SPR84
SPR152
SPR156
SPR152
6SPR04
6SPR06
SPR602C
6SPR02
6SPR04
SPR1002C
12SPR02
12SPR04
12SPR06
SPR1602C
SPR81
SPR81
SPR82
SPR82
SPR161C
SPR161C
SPR162C
SPR162C
SPR11

PAGE
NO.
C21
C21
C21
C25
C25
C25
C25
C25
C25
C25
C25
D5
D5
D5
D5
D5
D5
D5
D9
D9
D9
D9
D9
D9
D9
D9
D9
D9
D9
D9
D9
D9
D9
D9
D9
C21
C21
C21
C21
C25
C25
C25
C17
C17
D1
C17
C17
D3
C23
C23
C23
D5
C21
C21
C21
C21
D7
D7
D7
D7
C17

INDUSTRY
PART NO.
SF12
SF13
SF14
SF21
SF22
SF23
SF24
SF31
SF32
SF33
SF34
SF51
SF52
SF53
SF54
SF81
SF82
SF83
SF84
SF161
SF162
SF163
SF164
SF301
SF302
SF303
SF304
SF1401
SF1402
SF1403
SF1404
SF2001
SF2002
SF2003
SF2004
SF2401
SF2402
SF2403
SF2404
TG24
TG26
TG28
TG284
TG286
TG288
TG4
TG6
TG8
TG84
TG86
UF4001
UF4002
UF4003
UF4004
UF4005
UF4006
UF4007
UF5400
UF5401
UF5402
UF5404

SUGGESTED
DIOTEC
REPLACEMENT
PART NO.
SPR11
SPR12
SPR12
SPR21
SPR21
SPR22
SPR22
SPR31
SPR31
SPR32
SPR32
SPR51
SPR51
SPR52
SPR52
SPR81
SPR81
SPR82
SPR82
SPR161C
SPR161C
SPR162C
SPR162C
UFR3001C
UFR3001C
UFR3002C
UFR3002C
SPR81
SPR81
SPR82
SPR82
SPR150
SPR151
SPR152
SPR152
SPR161C
SPR161C
SPR162C
SPR162C
UFR24
UFR26
UFR28
UFR24
UFR24
UFR24
UFR104
UFR106
UFR108
SPR84
SPR86
UFR100
UFR101
UFR102
UFR104
UFR106
UFR108
UFR110
UFR300
UFR301
UFR302
UFR304

PAGE
NO.
C1
C1
C1
C5
C5
C5
C5
C7
C7
C7
C7
C13
C13
C13
C13
C21
C21
C21
C21
D7
D7
D7
D7
D9
D9
D9
D9
C21
C21
C21
C21
C25
C25
C25
C25
D7
D7
D7
D7
C5
C5
C5
C5
C5
C5
C3
C3
C3
C21
C21
C3
C3
C3
C3
C3
C3
C3
C9
C9
C9
C9

INDUSTRY
PART NO.
UF5406
UF5407
UF5408
UF600A
UF600B
UF600D
UF600G
UF600J
UF600K
UF600M
VHE1401
VHE1402
VHE1403
VHE1404
VHE205
VHE210
VHE215
VHE220
VHE2401
VHE2402
VHE2403
VHE2404
VHE605
VHE610
VHE615
VHE620

SUGGESTED
DIOTEC
REPLACEMENT
PART NO.
UFR306
UFR308
UFR310
UFR600
UFR601
UFR602
UFR604
UFR606
UFR608
UFR610
12SPR01
12SPR01
12SPR02
12SPR02
SPR21
SPR21
SPR22
SPR22
SPR161C
SPR161C
SPR162C
SPR162C
SPR51
SPR51
SPR52
SPR52

PAGE
NO.
C9
C9
C9
C15
C15
C15
C15
C15
C15
C15
C23
C23
C23
C23
C5
C5
C5
C5
D7
D7
D7
D7
C13
C13
C13
C13

III-2
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

BRIDGE RECTIFIER CROSS REFERENCE

SUGGESTED
DIOTEC
PAGE
REPLACEMENT NO.
PART NO.
2KBP005
SB200
E11
2KBP005M
SB200
E11
2KBP01
SB201
E11
2KBP01M
SB201
E11
2KBP02
SB202
E11
2KBP02M
SB202
E11
2KBP04
SB204
E11
2KBP04M
SB204
E11
2KBP06
SB206
E11
2KBP06M
SB206
E11
2KBP08
SB208
E11
2KBPO8M
SB208
E11
2KBP10
SB210
E11
2KBP10M
SB210
E11
2W005
WB200
E9
2W01
WB201
E9
2W02
WB202
E9
2W04
WB204
E9
2W06
WB206
E9
2W08
WB208
E9
2W10
WB210
E9
3N246
SB200
E11
3N247
SB201
E11
3N248
SB202
E11
3N249
SB204
E11
3N250
SB206
E11
3N251
SB208
E11
3N252
SB210
E11
3N253
SB200
E11
3N254
SB201
E11
3N255
SB202
E11
3N256
SB204
E11
3N257
SB206
E11
3N258
SB208
E11
3N259
SB210
E11
APBPC303
ADB304
E13
APBPC304
ADB304
E13
APBPC305
ADB306
E13
APBPC306
ADB308
E13
APBPC603
ADB604
E25
APBPC604
ADB604
E25
APBPC605
ADB606
E25
APBPC606
ADB606
E25
APBPC1502
ADB1504P
E37
APBPC1504
ADB1504P
E37
APBPC1506
ADB1506P
E37
APBPC1508
ADB1508P
E37
APBPC2502
ADB2504P
E41
APBPC2504
ADB2504P
E41
APBPC2506
ADB2506P
E41
APBPC2508
ADB2508P
E41
APBPC3502
ADB3504P
E45
APBPC3504
ADB3504P
E45
APBPC3506
ADB3506P
E45
APBPC3508
ADB3508P
E45
B125C1000M
WB154
E7
B125C1500M
WB154
E7
B125C3700/200 SB504
E21
B125C5000/3000 SB504
E21
B125C800M
WB154
E7
B125C800DM
DI104
E1
B250C1000M
WB156
E7
B250C1500M
WB156
E7
INDUSTRY
PART NO.

INDUSTRY
PART NO.
B250C3700/2200
B250C5000/3300
B250C800M
B250C800DM
B380C1000M
B380C1500M
B380C3700/2200
B380C5000/3300
B380C800M
B380C800DM
B40C1000M
B40C1500DM
B40C3700/2200
B40C5000/3000
B40C800M
B40C800DM
B80C1000M
B80C1500M
B80C3700/2200
80C5000/3000
B80C800M
B80C800DM
BR1505
BR151
BR1510
BR152
BR154
BR156
BR158
BR2505
BR252
BR254
BR256
BR258
BR3505
BR351
BR3510
BR352
BR354
BR356
BR358
BR605
BR61
BR610
BR62
BR64
BR66
BR68
BR805
BR805D
BR81D
BR81DF
BR81OD
BR81ODF
BR82D
BR82DF
BR84D
BR84DF
BR86D
BR86DF
BR88D
BR88DF
BR84D

SUGGESTED
DIOTEC
PAGE
REPLACEMENT NO.
PART NO.
SB506
E21
SB506
E21
WB156
E7
DI106
E11
WB151
E7
WB151
E7
SB510
E21
SB510
E21
WB151
E7
DI110
E11
WB151
E7
WB151
E7
SB501
E21
SB501
E21
WB151
E7
WB151
E7
WB152
E7
WB152
E7
SB502
E21
SB502
E21
WB152
E7
DI102
E11
DB1500P
E37
DB1501P
E37
DB1510P
E37
DB1502P
E37
DB1504P
E37
DB1506P
E37
DB1508P
E37
DB2500P
E41
DB2502P
E41
DB2504P
E41
DB2506P
E41
DB2508P
E41
DB3500P
E45
DB3501P
E45
DB3510P
E45
DB3502P
E45
DB3504P
E45
DB3506P
E45
DB3508P
E45
DB600
E25
DB601
E25
DB610
E25
DB602
E25
DB604
E25
DB606
E25
DB608
E25
SB200
E11
FSB200
G5
SB201
E11
FSB210
G5
SB210
E11
FSB201
G5
SB202
E11
FSB202
G5
SB204
E11
FSB204
G5
SB206
E11
FSB206
G5
SB208
E11
FSB208
G5
SB204
E11

SUGGESTED
INDUSTRY
DIOTEC
PAGE
PART NO. REPLACEMENT NO.
PART NO.
BR84DF
FSB204
G5
BR86D
SB206
E11
BR86DF
FSB206
G5
BR88D
SB208
E11
BR88DF
FSB208
G5
DB101
DI100
E1
DB102
DI101
E1
DB103
DI102
E1
DB104
DI104
E1
DB105
DI106
E1
DF04
DI104
E1
DF06
DI106
E1
DF08
DI108
E1
DF10
DI110
E1
GBPC1005 DB300
E13
GBPC101 DB301
E13
GBPC102 DB302
E13
GBPC104 DB304
E13
GBPC106 DB306
E13
GBPC108 DB308
E13
GBPC110 DB310
E13
GBPC6005 DB600
E25
GBPC601 DB601
E25
GBPC602 DB602
E25
GBPC604 DB604
E25
GBPC606 DB606
E25
GBPC608 DB608
E25
GBPC610 DB610
E25
GBPC12005 DB1500P
E37
GBPC1201 DB1501P
E37
GBPC1202 DB1502P
E37
GBPC1204 DB1504P
E37
GBPC1206 DB1506P
E37
GBPC1208 DB1508P
E37
GBPC1210 DB1510P
E37
GBPC15005 DB1500P
E37
GBPC1501 DB1501P
E37
GBPC1502 DB1502P
E37
GBPC1504 DB1504P
E37
GBPC1506 DB1506P
E37
GBPC1508 DB1508P
E37
GBPC1510 DB1510P
E37
GBPC25005 DB2500P
E41
GBPC2501 DB2501P
E41
GBPC2502 DB2502P
E41
GBPC2504 DB2504P
E41
GBPC2506 DB2506P
E41
GBPC2508 DB2508P
E41
GBPC2510 DB2510P
E41
GBPC35005 DB3500P
E45
GBPC3501 DB3501P
E45
GBPC3502 DB3502P
E45
GBPC3504 DB3504P
E45
GBPC3506 DB3506P
E45
GBPC3508 DB3508P
E45
GBPC3510 DB3510P
E45
GBU4A
SBU4A
E19
GBU4B
SBU4B
E19
GBU4D
SBU4D
E19
GBU4G
SBU4G
E19
GBU4J
SBU4J
E19
GBU4K
SBU4K
E19
GBU4M
SBU4M
E19

SUGGESTED
INDUSTRY
DIOTEC
PAGE
PART NO. REPLACEMENT NO.
PART NO.
GBU6A
SBU6A
E23
GBU6D
SBU6D
E23
GBU6G
SBU6G
E23
GBU6J
SBU6J
E23
GBU6K
SBU6K
E23
GBU6M
SBU6M
E23
GBU8A
SBU8A
E23
GBU8B
SBU8B
E29
GBU8D
SBU8D
E29
GBU8G
SBU8G
E29
GBU8J
SBU8J
E29
GBU8K
SBU8K
E29
GBU8M
SBU8M
E29
KBL005
SB400L
E15
KBL01
SB401L
E15
KBL02
SB402L
E15
KBL04
SB404L
E15
KBL06
SB406L
E15
KBL08
SB408L
E15
KBL10
SB410L
E15
KBP005M SB200
E11
KBP01M
SB201
E11
KBP02M
SB202
E11
KBP04M
SB204
E11
KBP06M
SB206
E11
KBP08M
SB208
E11
KBP10M
SB210
E11
KBPC10-OO5DB1500P
E37
KBPC10-O1 DB1501P
E37
KBPC10-O2 DB1502P
E37
KBPC10-O4 DB1504P
E37
KBPC10-O6 DB1506P
E37
KBPC10-O8 DB1508P
E37
KBPC10-10 DB1510P
E37
KBPC25005 DB2500P
E41
KBPC2501 DB2501P
E41
KBPC2502 DB2502P
E41
KBPC2504 DB2504P
E41
KBPC2506 DB2506P
E41
KBPC2508 DB2508P
E41
KBPC2510 DB2510P
E41
KBPC35005 DB3500P
E45
KBPC3501 DB3501P
E45
KBPC3502 DB3502P
E45
KBPC3504 DB3504P
E45
KBPC3506 DB3506P
E45
KBPC3508 DB3508P
E45
KBPC3510 DB3510P
E45
KBPC6005 DB600
E25
KBPC601 DB601
E25
KBPC602 DB602
E25
KBPC604 DB604
E25
KBPC606 DB606
E25
KBPC608 DB608
E25
KBPC610 DB610
E25
KBPC8005 DB800
E31
KBPC801 DB801
E31
KBPC802 DB802
E31
KBPC804 DB804
E31
KBPC806 DB806
E31
KBPC808 DB808
E31
KBPC810 DB810
E31
KBU4A
SBU4A
E19

IV-1
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

BRIDGE RECTIFIER CROSS REFERENCE

INDUSTRY
PART NO.
KBU4B
KBU4D
KBU4G
KBU4J
KBU4K
KBU4M
KBU6A
KBU6B
KBU6D
KBU6G
KBU6J
KBU6K
KBU6M
KBU8A
KBU8B
KBU8D
KBU8G
KBU8J
KBU8K
KBU8M
MB1005
MB101
MB102
MB104
MB106
MB108
MB1505
MB151
MB152
MB154
MB156
MB158
MB2505
MB251
MB252
MB254
MB256
MB258
MB3505
MB351
MB352
MB354
MB356
MB358
MB805
MB81
MB82
MB84
MB86
MB88
MDA100A
MDA101A
MDA102A
MDA104A
MDA106A
MDA108A
MDA110A
MDA200
MDA201
MDA202
MDA204
MDA206
MDA208

SUGGESTED
DIOTEC
PAGE
REPLACEMENT NO.
PART NO.
SBU4B
E19
SBU4D
E19
SBU4G
E19
SBU4J
E19
SBU4K
E19
SBU4M
E19
SBU6A
E23
SBU6B
E23
SBU6D
E23
SBU6G
E23
SBU6J
E23
SBU6K
E23
SBU6M
E23
SBU8A
E29
SBU8B
E29
SBU8D
E29
SBU8G
E29
SBU8J
E29
SBU8K
E29
SBU8M
E29
DB1000
E33
DB1001
E33
DB1002
E33
DB1004
E33
DB1006
E33
DB1008
E33
DB1500P
E37
DB1501P
E37
DB1502P
E37
DB1504P
E37
DB1506P
E37
DB1508P
E37
DB2500P
E41
DB2501P
E41
DB2502P
E41
DB2504P
E41
DB2506P
E41
DB2508P
E41
DB3500P
E45
DB3501P
E45
DB3502P
E45
DB3504P
E45
DB3506P
E45
DB3508P
E45
DB1000
E33
DB1001
E33
DB1002
E33
DB1004
E33
DB1006
E33
DB1008
E33
SB200
E11
SB201
E11
SB202
E11
SB204
E11
SB206
E11
SB208
E11
SB210
E11
SB200
E11
SB201
E11
SB202
E11
SB202
E11
SB206
E11
SB208
E11

SUGGESTED
INDUSTRY
DIOTEC
PAGE
PART NO. REPLACEMENT NO.
PART NO.
MDA210
SB210
E11
MDA2500 DB3500P
E45
MDA2501 DB3501P
E45
MDA2502 DB3502P
E45
MDA2504 DB3504P
E45
MDA2506 DB3506P
E45
MDA3500 DB3500P
E45
MDA3501 DB3501P
E45
MDA3502 DB3502P
E45
MDA3504 DB3504P
E45
MDA3506 DB3506P
E45
MDA3508 DB3508P
E45
MDA3510 DB3510P
E45
MDA970A1 SB400L
E15
MDA970A2 SB401L
E15
MDA970A3 SB402L
E15
MDA970A5 SB404L
E15
MDA970A6 SB406L
E15
MP1005
DB1000
E33
MP101
DB1001
E33
MP1010
DB1010
E33
MP102
DB1002
E33
MP104
DB1004
E33
MP106
DB1006
E33
MP108
DB1008
E33
MP605
DB600
E25
MP61
DB601
E25
MP610
DB610
E25
MP62
DB602
E25
MP64
DB604
E25
MP66
DB606
E25
MP68
DB608
E25
MP805
DB1000
E33
MP81
DB1001
E33
MP810
DB1010
E33
MP82
DB1002
E33
MP84
DB1004
E33
MP86
DB1006
E33
MP88
DB1008
E33
PB305
DB300
E13
PB305F
FDB300
G7
PB31
DB301
E13
PB31F
FDB301
G7
PB310
DB310
E13
PB310F
FDB310
G7
PB32
DB302
E13
PB32F
FDB302
G7
PB34
DB304
E13
PB34F
FDB304
G7
PB36
DB306
E13
PB36F
FDB306
G7
PB38
DB308
E13
PB38F
FDB308
G7
PB605
DB600
E25
PB605F
FDB600
G9
PB61`
DB601
E25
PB61F
FDB601
G9
PB610
DB610
E25
PB610F
FDB610
G9
PB62
DB602
E25
PB62F
FDB602
G9
PB64
DB604
E25
PB64F
FDB604
G9

SUGGESTED
INDUSTRY
DIOTEC
PAGE
PART NO. REPLACEMENT NO.
PART NO.
PB66
DB606
E25
PB66F
FDB606
G9
PB68
DB608
E25
PB68F
FDB608
G9
PBDF101
DI100
E1
PBDF102
DI101
E1
PBDF103
DI102
E1
PBDF104
DI104
E1
PBDF105
DI106
E1
PBDF106
DI108
E1
PBDF107
DI110
E1
PBL301
SB400L
E15
PBL302
SB401L
E15
PBL303
SB402L
E15
PBL304
SB404L
E15
PBL305
SB406L
E15
PBL306
SB408L
E15
PBL307
SB410L
E15
PBL401
SB400L
E15
PBL402
SB401L
E15
PBL403
SB402L
E15
PBL404
SB404L
E15
PBL405
SB406L
E15
PBL406
SB408L
E15
PBL407
SB410L
E15
PBM101
WB150
E7
PBM102
WB151
E7
PBM103
WB152
E7
PBM104
WB154
E7
PBM105
WB156
E7
PBM106
WB108
E7
PBM107
WB1510
E7
PBM151
WB150
E7
PBM152
WB151
E7
PBM153
WB152
E7
PBM154
WB154
E7
PBM155
WB156
E7
PBM156
WB158
E7
PBM156
WB1510
E7
PBM201
WB200
E5
PBM202
WB201
E5
PBM203
WB202
E5
PBM204
WB204
E5
PBM205
WB206
E5
PBM206
WB208
E5
PBM207
WB210
E5
PBP151
SB200
E11
PBP152
SB201
E11
PBP153
SB202
E11
PBP154
SB204
E11
PBP155
SB206
E11
PBP156
SB208
E11
PBP157
SB210
E11
PBP201
SB200
E11
PBP202
SB201
E11
PBP203
SB202
E11
PBP204
SB204
E11
PBP205
SB206
E11
PBP206
SB208
E11
PBP207
SB210
E11
PBPC1001 DB1000
E33
PBPC1002 DB1001
E33
PBPC1003 DB1002
E33

SUGGESTED
DIOTEC
PAGE
REPLACEMENT NO.
PART NO.
PBPC1004
DB1004
E33
PBPC1005
DB1006
E33
PBPC1006
DB1008
E33
PBPC1007
DB1010
E33
PBPC301
DB300
E13
PBPC302
DB302
E13
PBPC303
DB304
E13
PBPC304
DB304
E13
PBPC305
DB306
E13
PBPC306
DB308
E13
PBPC307
DB310
E13
PBPC601
DB600
E25
PBPC602
DB601
E25
PBPC603
DB602
E25
PBPC604
DB604
E25
PBPC605
DB606
E25
PBPC606
DB608
E25
PBPC607
DB610
E25
PBPC801
DB800
E31
PBPC802
DB801
E31
PBPC803
DB802
E31
PBPC804
DB804
E31
PBPC805
DB806
E31
PBPC806
DB808
E31
PBPC807
DB810
E31
PBU1001
SBU8A
E29
PBU1002
SBU8B
E29
PBU1003
SBU8D
E29
PBU1004
SBU8G
E29
PBU1005
SBU8J
E29
PBU1006
SBU8K
E29
PBU1007
SBU8M
E29
PBU401
SBU4A
E19
PBU402
SBU4B
E19
PBU403
SBU4D
E19
PBU404
SBU4G
E19
PBU405
SBU4J
E19
PBU406
SBU4K
E19
PBU407
SBU4M
E19
PBU601
SBU6A
E23
PBU602
SBU6B
E23
PBU603
SBU6D
E23
PBU604
SBU6G
E23
PBU605
SBU6J
E23
PBU606
SBU6K
E23
PBU607
SBU6M
E23
PBU801
SBU8A
E29
PBU802
SBU8B
E29
PBU803
SBU8D
E29
PBU804
SBU8G
E29
PBU805
SBU8J
E29
PBU806
SBU8K
E29
PBU807
SBU8M
E29
RDF005M
FDI100
G1
RDF01M
FDI101
G1
RDF02M
FDI102
G1
RDF04M
FDI104
G1
RDF06M
FDI106
G1
RDF08M
FDI108
G1
RKBPC15005 FDB2500P
E41
RKBPC1501 FDB2501P
E41
RKBPC1502 FDB2502P
E41
RKBPC1504 FDB2504P
E41
INDUSTRY
PART NO.

IV-1
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

BRIDGE RECTIFIER CROSS REFERENCE

SUGGESTED
DIOTEC
REPLACEMENT
PART NO.
RKBPC1506 FDB2506P
RKBPC1508 FDB2508P
RKBPC1510 FDB2510P
RKBPC25005 FDB2500P
RKBPC2501 FDB2501P
RKBPC2502 FDB2502P
RKBPC2504 FDB2504P
RKBPC2506 FDB2506P
RKBPC2508 FDB2508P
RKBPC2510 FDB2510P
RKBPC35005 FDB3500
RKBPC3501 FDB3501
RKBPC3502 FDB3502
RKBPC3504 FDB3504
RKBPC3506 FDB3506
RKBPC3508 FDB3508
RPBDF101
FDI100
RPBDF102
FDI101
RPBDF103
FDI102
RPBDF104
FDI104
RPBDF105
FDI106
RPBDF106
FDI108
RPBDF107
FDI104
RPBPC301
FDB300
RPBPC302
FDB301
RPBPC303
FDB302
RPBPC304
FDB304
RPBPC305
FDB306
RPBPC306
FDB308
RPBPC307
FDB310
RPBPC601
FDB600
RPBPC602
FDB601
RPBPC603
FDB602
RPBPC604
FDB604
RPBPC605
FDB606
RPBPC606
FDB608
RPBPC607
FDB610
RS101
SB200
RS102
SB201
RS103
SB202
RS104
SB204
RS105
SB206
RS106
SB208
RS107
SB210
RS201
SB200
RS202
SB201
RS203
SB202
RS204
SB204
RS205
SB206
RS206
SB208
RS207
SB210
RS401S
SB400L
RS402S
SB401L
RS403S
SB402L
RS404S
SB404L
RS405S
SB406L
RS406S
SB408L
RS407S
SB410L
RS401L
SB400L
RS402L
SB401L
RS403L
SB402L
RS404L
SB404L
RS405L
SB406L
INDUSTRY
PART NO.

PAGE
NO.
G15
G15
G15
G15
G15
G15
G15
G15
G15
G15
G13
G13
G13
G13
G13
G13
G1
G1
G1
G1
G1
G1
G1
G7
G7
G7
G7
G7
G7
G7
G9
G9
G9
G9
G9
G9
G9
E11
E11
E11
E11
E11
E11
E11
E11
E11
E11
E11
E11
E11
E11
E15
E15
E15
E15
E15
E15
E15
E15
E15
E15
E15
E15

SUGGESTED
INDUSTRY
DIOTEC
PART NO. REPLACEMENT
PART NO.
RS406L
SB408L
RS407L
SB410L
RS601
SBU6A
RS602
SBU6B
RS603
SBU6D
RS604
SBU6G
RS605
SBU6J
RS606
SBU6K
RS607
SBU6M
SCB15005 DB1500P
SCB1501
DB1501P
SCB1502
DB1502P
SCB1504
DB1504P
SCB1506
DB1506P
SCB1508
DB1508P
SCB1510
DB1510P
SCB25005 DB2500P
SCB2501
DB2501P
SCB2502
DB2502P
SCB2504
DB2504P
SCB2506
DB2506P
SCB2508
DB2508P
SCB2510
DB2510P
SCB35005 DB3500P
SCB3501
DB3501P
SCB3502
DB3502P
SCB3504
DB3504P
SCB3506
DB3506P
SCB3508
DB3508P
SCB3510
DB35010P
VE08
WB150
VE08X
FWB150
VE108
WB1510
VE18
WB151
VE18X
FWB151
VE28
WB152
VE28X
FWB152
VE48
WB154
VE48X
FWB154
VE68
WB156
VE68X
FWB156
VE88
WB158
VH048
DB600
VH048X
FDB600
VH1048
DB610
VH1048X
FDB610
VH148
DB601
VH148X
FDB601
VH247
ADB604
VH248
DB602
VH248X
FDB602
VH447
ADB604
VH448
DB604
VH448X
FDB604
VH647
ADB606
VH648
DB606
VH648X
FDB606
VH847
ADB608
VH848
DB608
VJ048
DB1000
VJ048X
Call DIOTEC
VJ1048
DB1010
VJ148
DB1001

PAGE
NO.
E15
E15
E23
E23
E23
E23
E23
E23
E23
E37
E37
E37
E37
E37
E37
E37
E41
E41
E41
E41
E41
E41
E41
E45
E45
E45
E45
E45
E45
E45
E7
G3
E7
E7
G3
E7
G3
E7
G3
E7
G3
E7
E25
G9
E25
G9
E25
G9
E25
E25
G9
E25
E25
G9
E25
E25
G9
E25
E25
E33
E33
E33

SUGGESTED
INDUSTRY
DIOTEC
PART NO. REPLACEMENT
PART NO.
VJ148X
Call DIOTEC
VJ247
ADB1004
VJ248
DB1002
VJ248X
Call DIOTEC
VJ447
ADB1004
VJ448
DB1004
VJ647
ADB1006
VJ648
DB1006
VJ847
ADB1008
VJ848
DB1008
VK048
DB3500P
VK048X
FDB3500P
VK1048
DB3510P
VK148
DB3501P
VK148X
FDB3501P
VK247
ADB3504P
VK248
DB3502P
VK248X
FDB3502P
VK447
ADB3504P
VK448
DB3504P
VK448X
FDB3504P
VK647
ADB3506P
VK648
DB3506P
VK648X
FDB3506P
VK848
DB3508P
VL048
DB1500P
VL1048
DB1510P
VL148
DB1501P
VL247
ADB1504P
VL248
DB1502P
VL447
ADB1504P
VL448
DB1504P
VL647
ADB1506P
VL648
DB1506P
VL848
DB1508P
VM08
DI100
VM08X
FDI100
VM108
DI110
VM18
DI101
VM18X
FDI101
VM28
DI102
VM28X
FDI102
VM48
DI104
VM48X
FDI104
VM68
DI106
VM68X
FDI106
VM88
DI108
VS048
DB300
VS048X
FDB300
VS1048
DB310
VS148
DB301
VS148X
FDB301
VS247
ADB304
VS248
DB302
VS248X
FDB302
VS447
ADB304
VS448
DB304
VS448X
FDB304
VS647
ADB306
VS648
DB306
VS648X
FDB306
VS847
ADB308
VS848
DB308

PAGE
NO.

E33
E33
E33
E33
E33
E33
E33
E33
E45
G17
E45
E45
G17
E45
E45
G17
E45
E45
G17
E45
E45
G17
E45
E37
E37
E37
E37
E37
E37
E37
E37
E37
E37
E1
G1
E1
E1
G1
E1
G1
E1
G1
E1
G1
E1
E13
G7
E13
E13
G7
E13
E13
G7
E13
E13
G7
E13
E13
G7
E13
E13

SUGGESTED
INDUSTRY
DIOTEC
PART NO. REPLACEMENT
PART NO.
W005M
WB150
W01M
WB151
W02M
WB152
W04M
WB154
W06M
WB156
W08M
WB158
W10M
WB1510
W10M
WB1510

PAGE
NO.
E7
E7
E7
E7
E7
E7
E7
E7

IV-1
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

SILICON DIODE CROSS REFERENCE

SUGGESTED
INDUSTRY
DIOTEC
PAGE
PART NO. REPLACEMENT NO.
PART NO.
1N4001
1N4001
H1
1N4001GP 1N4001G
H3
1N4002
1N4002
H1
1N4002GP 1N4002G
H3
1N4003
1N4003
H1
1N4003GP 1N4003G
H3
1N4004
1N4004
H1
1N4004GP 1N4004G
H3
1N4005
1N4005
H1
1N4005GP 1N4005G
H3
1N4006
1N4006
H1
1N4006GP 1N4006G
H3
1N4007
1N4007
H1
1N4007GP 1N4007G
H3
1N4933
1N4933
H21
1N4933GP RGP100
H25
1N4934
1N4934
H21
1N4934GP RGP101
H25
1N4935
1N4935
H21
1N4935GP RGP102
H25
1N4936
1N4936
H21
1N4936GP RGP104
H25
1N4937
1N4937
H21
1N4937GP RGP106
H25
1N4942
RGP102
H25
1N4942GP RGP102
H25
1N4944
RGP104
H25
1N4944GP RGP104
H25
1N4946
RGP106
H25
1N4946GP RGP106
H25
1N4947
RGP108
H25
1N4947GP RGP108
H25
1N4948
RGP110
H25
1N4948GP RGP110
H25
1N5059(GP) RGP102
H25
1N5060(GP) RGP104
H25
1N5061(GP) RGP106
H25
1N5062(GP) RGP108
H25
1N5391
1N5391
H7
1N5391GP 1N5391
H7
1N5392
1N5392
H7
1N5392GP 1N5392
H7
1N5393
1N5393
H7
1N5393GP 1N5393
H7
1N5394
1N5395
H7
1N5394GP 1N5395
H7
1N5395
1N5395
H7
1N5395GP 1N5395
H7
1N5396
1N5397
H7
1N5396GP 1N5397
H7
1N5397
1N5397
H7
1N5397GP 1N5397
H7
1N5398
1N5398
H7
1N5398GP 1N5398
H7
1N5399
1N5399
H7
1N5399GP 1N5399
H7
1N5400
1N5400
H11
1N5401
1N5401
H11
1N5402
1N5402
H11
1N5403
1N5404
H11
1N5404
1N5404
H11
1N5405
1N5406
H11
1N5406
1N5406
H11

INDUSTRY
PART NO.
1N5615(GP)
1N5616(GP)
1N5617(GP)
1N5618(GP)
1N5619(GP)
1N5620(GP)
1N5621(GP)
1N5622(GP)
1N5623(GP)
1N5624(GP)
1N5625(GP)
1N5626(GP)
1N5627(GP)
6A05
6A05G
6A1
6A1G
6A2
6A2G
6A4
6A4G
6A6
6A6G
6A8
6A10
BY214-50
BY214-100
BY214-200
BY214-400
BY214-600
BY218-100
BY218-200
BY218-400
BY218-600
BY233-200A
BY233-400A
BY233-600A
BY251
BY252
BY253
BY254
BY254S
BY255
BY296
BY297
BY296
BY298
BY299
BY396
BY397
BY398
BY399
BYT13-600
BYT13-800
BYT71-100A
BYT71-400A
BYT71-600A
BYW32
BYW33
BYW34
BYW35
BYW36
BYW72

SUGGESTED
DIOTEC
PAGE
REPLACEMENT NO.
PART NO.
RGP102
H25
RGP104
H25
RGP104
H25
RGP106
H25
RGP106
H25
RGP108
H25
RGP108
H25
RGP110
H25
RGP110
H25
RGP302
H31
RGP304
H31
RGP306
H31
RGP308
H31
GP600
H17
GP600
H17
GP601
H17
GP601
H17
GP602
H17
GP602
H17
GP604
H17
GP604
H17
GP606
H17
GP606
H17
GP608
H17
GP610
H17
GP600
H17
GP601
H17
GP602
H17
GP604
H17
GP606
H17
RGP301
H31
RGP302
H31
RGP304
H31
RGP306
H31
RGP802
H35
RGP804
H35
RGP806
H35
GP402
H15
GP404
H15
GP406
H15
GP408
H15
GP410
H15
GP410
H15
RGP301
H31
RGP302
H31
RGP304
H31
RGP306
H31
RGP308
H31
RGP301
H31
RGP302
H31
RGP304
H31
RGP308
H31
RGP306
H31
RGP308
H31
RGP801
H35
RGP804
H35
RGP806
H35
RGP202
H27
RGP204
H27
RGP204
H27
RGP206
H27
RGP206
H27
RGP302
H31

INDUSTRY
PART NO.
BYW73
BYW74
BYW75
BYW76
DI750
DI751
DI752
DI754
DIF810
DIF811
DIF812
DIF814
DIF816
DIF817
DIF818
DIF910
DIF911
DIF912
DIF914
DIF916
DIF917
DIF918
DIR500
DIR501
DIR502
DIR504
DIR506
DIR508
DIR510
ESM765-100A
ESM765-200A
ESM765-400A
ESM765-600A
FR101
FR101G
FR102
FR102G
FR103
FR103G
FR104
FR104G
FR105
FR105G
FR106
FR107
FR151
FR151G
FR152
FR152G
FR153
FR153G
FR154
FR154G
FR155
FR155G
FR156
FR157
FR201
FR201G
FR202
FR202G
FR203
FR203G

SUGGESTED
DIOTEC
PAGE
REPLACEMENT NO.
PART NO.
RGP304
H31
RGP304
H31
RGP306
H31
RGP306
H31
GP600
H17
GP601
H17
GP602
H17
GP604
H17
RP100
H23
RP101
H23
RP102
H23
RP104
H23
RP106
H23
RP108
H23
RP110
H23
RGP300
H31
RGP301
H31
RGP302
H31
RGP304
H31
RGP306
H31
RGP308
H31
RGP310
H31
GP400
H15
GP401
H15
GP402
H15
GP404
H15
GP406
H15
GP408
H15
GP410
H15
RGP801
H35
RGP802
H35
RGP804
H35
RGP806
H35
RP100
H23
RGP100
H25
RP101
H23
RGP101
H25
RP102
H23
RGP102
H25
RP104
H23
RGP104
H25
RP106
H23
RGP106
H25
RP108
H23
RP110
H25
RGP200
H27
RGP200
H27
RGP201
H27
RGP201
H27
RGP202
H27
RGP202
H27
RGP204
H27
RGP204
H27
RGP206
H27
RGP206
H27
RGP206
H27
RGP208
H27
RGP200
H27
RGP200
H27
RGP201
H27
RGP201
H27
RGP202
H27
RGP202
H27

SUGGESTED
INDUSTRY
DIOTEC
PAGE
PART NO. REPLACEMENT NO.
PART NO.
FR204
RGP204
H27
FR204G
RGP204
H27
FR205
RGP206
H27
FR205G
RGP206
H27
FR206
RGP208
H27
FR207
RGP210
H27
FR301
RP300
H29
FR301G
RGP300
H31
FR302
RP301
H29
FR302G
RP301
H31
FR303
RP302
H29
FR303G
RGP302
H31
FR304
RP304
H29
FR304G
RGP304
H31
FR305
RP306
H29
FR305G
RGP306
H31
FR306
RP308
H29
FR307
RGP308
H31
FR501
RP600
H33
FR502
RP601
H33
FR503
RP602
H33
FR504
RP604
H33
FR505
RP606
H33
FR506
RP608
H33
FR507
RP601
H33
FR601
RP600
H33
FR601G
RP600
H33
FR602
RP601
H33
FR602G
RP601
H33
FR603
RP602
H33
FR603G
RP602
H33
FR604
RP604
H33
FR604G
RP604
H33
FR605
RP606
H33
FR605G
RP606
H33
FR606
RP608
H33
FR607
RP610
H33
FR801
RGP800
H35
FR802
RGP801
H35
FR803
RGP802
H35
FR804
RGP804
H35
FR805
RGP806
H35
GI750
GP600
H17
GI751
GP601
H17
GI752
GP602
H17
GI754
GP604
H17
GI756
GP606
H17
GI758
GP608
H17
GI810
RGP200
H27
GI811
RGP201
H27
GI812
RGP202
H27
GI814
RGP204
H27
GI816
RGP206
H27
GI817
RGP208
H27
GI818
RGP210
H27
GI820
RP600
H33
GI821
RP601
H33
GI822
RP602
H33
GI824
RP604
H33
GI826
RP606
H33
GP10A
GP100
H5
GP10B
GP101
H5
GP10D
GP102
H5

V-1
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

SILICON DIODE CROSS REFERENCE (Cont'd)

INDUSTRY
PART NO.
GP10G
GP10J
GP10K
GP10M
GP15A
GP15B
GP15D
GP15G
GP15J
GP15K
GP15M
GP20A
GP20B
GP20D
GP20G
GP20J
GP20K
GP20M
GP30A
GP30B
GP30D
GP30G
GP30J
GP30K
GP30M
JO5
JO5G
J1
J1G
J2
J2G
J4
J4G
J6
J6G
J8
J10
MR500
MR501
MR502
MR504
MR506
MR508
MR510
MR750
MR751
MR752
MR754
MR756
MR758
MR760
P300A
P300B
P300D
P300G
P300J
P300K
P300M
P511
P513
P600A
P600B
P600D

SUGGESTED
DIOTEC
PAGE
REPLACEMENT NO.
PART NO.
GP104
H5
GP106
H5
GP108
H5
GP110
H5
GP200
H9
GP201
H9
GP202
H9
GP204
H9
GP206
H9
GP208
H9
GP210
H9
GP200
H9
GP201
H9
GP202
H9
GP204
H9
GP206
H9
GP208
H9
GP210
H9
GP400
H15
GP401
H15
GP402
H15
GP404
H15
GP406
H15
GP408
H15
GP410
H15
GP200
H9
RGP200
H27
GP201
H9
RGP201
H27
GP202
H9
RGP202
H27
GP204
H9
RGP204
H27
GP206
H9
RGP206
H27
GP208
H9
GP210
H9
GP400
H15
GP401
H15
GP402
H15
GP404
H15
GP406
H15
GP408
H15
GP410
H15
GP400
H15
GP600
H17
GP601
H17
GP602
H17
GP604
H17
GP608
H17
GP610
H17
GP400
H15
GP401
H15
GP402
H15
GP404
H15
GP406
H15
GP408
H15
GP410
H15
RGP1150
I3
RGP1180
I3
GP600
H17
GP601
H17
GP602
H17

SUGGESTED
INDUSTRY
DIOTEC
PAGE
PART NO. REPLACEMENT NO.
PART NO.
P600G
GP604
H17
P600J
GP606
H17
P600K
GP608
H17
P600M
GP610
H17
PF4HZ
GP404
H15
PF6HZ
GP406
H15
PF8HZ
GP408
H15
PFR850
RP300
H29
PFR851
RP301
H29
PFR852
RP302
H29
PFR854
RP304
H29
PFR856
RP306
H29
PL4HZ
1N4004G
H33
PL6HZ
1N4006G
H33
PL8HZ
1N4008G
H33
PLR810
RGP200
H27
PLR811
RGP201
H27
PLR812
RGP202
H27
PLR813
RGP204
H27
PLR814
RGP204
H27
PLR816
RGP206
H27
PLR817
RGP208
H27
PLR818
RGP210
H27
PR1001
RP100
H23
PR1002
RP101
H23
PR1003
RP102
H23
PR1004
RP104
H23
PR1005
RP106
H23
PR1006
RP108
H23
PR1007
RP110
H23
PR121
GP1120
I1
PR141
RGP1150
H27
PR1501
RGP200
H27
PR1502
RGP201
H27
PR1503
RGP202
H27
PR1504
RGP204
H27
PR1505
RGP206
H27
PR1506
RGP206
H27
PR1507
RGP208
H27
PR3001
RP300
H29
PR3002
RP301
H29
PR3003
RP302
H29
PR3004
RP304
H29
PR3005
RP306
H29
PR3006
RP308
H29
PR3007
RP308
H29
PR6001
RP600
H33
PR6002
RP601
H33
PR6003
RP602
H33
PR6004
RP604
H33
PR6005
RP606
H33
PR6006
RP608
H33
PR6007
RP610
H33
PX4A01
GP400
H15
PX4A02
GP401
H15
PX4A03
GP402
H15
PX4A04
GP404
H15
PX4A05
GP406
H15
PX4A06
GP408
H15
PX4A07
GP410
H15
PX6A01
RP600
H17
PX6A02
GP601
H17
PX6A03
GP602
H17

SUGGESTED
INDUSTRY
DIOTEC
PAGE
PART NO. REPLACEMENT NO.
PART NO.
PX6A04
GP604
H17
PX6A05
GP606
H17
PX6A06
GP608
H17
PX6A07
GP610
H17
PY124
RGP202
H27
PY125
GP204
H9
PY126
GP206
H9
PY55-350 RGP204
H27
PY55-600 RGP206
H27
RG4A
RGP300
H31
RG4B
RGP301
H31
RG4D
RGP302
H31
RG4G
RGP304
H31
RG4J
RGP306
H31
RG4K
RGP308
H31
RG4M
RGP310
H31
RGP10A
RGP100
H25
RGP10B
RGP101
H25
RGP10D
RGP102
H25
RGP10G
RGP104
H25
RGP10J
RGP106
H25
RGP10K
RGP108
H25
RGP10M
RGP110
H25
RGP15A
RGP200
H27
RGP15B
RGP201
H27
RGP15D
RGP202
H27
RG1A
RGP100
H25
RG1B
RGP101
H25
RG1D
RGP102
H25
RG1G
RGP104
H25
RG1J
RGP106
H25
RG1K
RGP108
H25
RG1M
RGP110
H25
RG2A
RGP200
H27
RG2B
RGP201
H27
RG2D
RGP202
H27
RG2G
RGP204
H27
RG2J
RGP206
H27
RG2K
RGP208
H27
RG2M
RGP210
H27
RG3A
RGP300
H31
RG3B
RGP301
H31
RG3D
RGP302
H31
RG3G
RGP304
H31
RG3J
RGP306
H31
RG3K
RGP308
H31
RG3M
RGP310
H31
RGP15G
RGP204
H27
RGP15J
RGP206
H27
RGP15K
RGP208
H27
RGP15M
RGP210
H27
RGP20A
RGP200
H27
RGP20B
RGP201
H27
RGP20D
RGP202
H27
RGP20G
RGP204
H27
RGP20J
RGP206
H27
RGP20K
RGP208
H27
RGP20M
RGP210
H27
RGP25A
RGP300
H31
RGP25B
RGP301
H31
RGP25D
RGP302
H31
RGP25G
RGP304
H31
RGP25J
RGP306
H31

SUGGESTED
INDUSTRY
DIOTEC
PAGE
PART NO. REPLACEMENT
NO.
PART NO.
RGP25K
RGP308
H31
RGP25M
RGP310
H31
RGP30A
RGP300
H31
RGP30B
RGP301
H31
RGP30D
RGP302
H31
RGP30G
RGP304
H31
RGP30J
RGP306
H31
RGP30K
RGP308
H31
RGP30M
RGP310
H31
RL201
GP200
H9
RL201G
GP200
H9
RL202
GP201
H9
RL202G
GP201
H9
RL203
GP202
H9
RL203G
GP202
H9
RL204
GP204
H9
RL204G
GP204
H9
RL205
GP206
H9
RL205G
GP206
H9
RL206
GP208
H9
RL207
GP210
H9
RS8AT
RGP800
H35
RS8BT
RGP801
H35
RS8DT
RGP802
H35
RS8GT
RGP804
H35
RS8JT
RGP806
H35
V322
GP402
H15
V324
GP404
H15
V326
GP406
H15
V328
GP408
H15
V330
GP400
H15
V330X
RGP300
H31
V331
GP401
H15
V331X
RGP301
H31
V332
GP402
H15
V332X
RGP302
H31
V334
GP404
H15
V334X
RGP304
H31
V336
GP406
H15
V336X
RGP306
H31
V342
GP404
H15
V344
GP404
H15
V346
GP406
H15
V348
GP408
H15
V350
GP400
H15
V350X
RGP300
H31
V351
GP401
H15
V351X
RGP301
H31
V3510
GP410
H15
V352
GP402
H15
V352X
RGP302
H31
V354
GP404
H15
V354X
RGP304
H31
V356
GP406
H15
V356X
RGP306
H31
V358
GP408
H15

V-2
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

C ... Degrees Centigrade

C/W .. Degrees Centigrade per Watt
.................................................... Ohms
A .. Microamperes
S or Sec . Microseconds
A Amperes
AC . Alternating Current
CJ.... Junction Capacitance
cm... Centimeter
DIA. Diameter
DC.. Direct Current
DUT Diode Under Test
EIA . Electronic Industries Alliance
Hz Hertz
IF.. Forward Current
IFSM . Peak Forward Surge Current
In-lb ... Inch - Pounds
IO Average Forward Rectified Current
IR DC Reverse Current
IRM . Maximum DC Reverse Current at Rated Blocking Voltage
IRR .. Repetitive Reverse Current
IRSM Maximum Non-Repetitive Surge Current
2
I t ... Thermal Energy (Rating For Fusing)
JEDEC ... Joint Electron Device Engineering Council (of The EIA)
Kgs . Kilograms
MHz ... MegaHertz
mm . Millimeters
mS .. Millisecond
nS ... Nanosecond
pF ... Picofarad
PR ... Continuous Power Dissipation in The V (BR) Region
PRM . Maximum Power Dissipation in The V(BR) Region
RMS ... Root Mean Square
RCF . Thermal Resistance - Case to Fin
RJA . Thermal Resistance - Junction to Ambient
RJC . Thermal Resistance - Junction to Case
RJL . Thermal Resistance - Junction to Lead
TA Ambient Temperature
TC Case Temperature
TJ . Junction Temperature
TL Lead Temperature
TRR .. Reverse Recovery Time
TSTG . Storage Temperature
U/L or UL ... Underwriters Laboratories
V(BR) Breakdown (Avalanche) Voltage
V(BR)Max Breakdown (Avalanche) Voltage
V(BR)Min Breakdown (Avalanche) Voltage
VDC . D. C. Voltage
VFM . Maximum Forward Voltage Drop
VISO . Minimum Insulation Breakdown Voltage
VR ... Reverse Voltage
VRM . Maximum Reverse (Blocking) Voltage
VRSM Maximum Non-Recurrent Reverse Voltage
VRRM Maximum Recurrent Reverse Voltage
VR(RMS) . RMS Reverse Voltage
VRSM RMS Reverse Voltage
VRWM Working Peak Reverse Voltage
O

VI-1
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

PART NUMBER
Numbered
1N4001-1N4007
1N4001G-1N4007G
1N4148
1N4933-1N4937
1N5391-1N5399
1N5400-1N5408
1N5400G-1N5408G
1N5817-1N5819
1N5820-1N5822
6SK40-6SK100
6SPR01-6SPR05
8SPR01-8SPR05
12SPR01-12SPR05
12SK40-12SK100
16SK40-16SK100
30SK30-30SK70
A.
ADB304-ADB308
ADB604-ADB608
ADB804-ADB808
ADB1004-ADB1008
ADB1504-ADB1508
ADB1504P-ADB1508P
ADB2504-ADB2508
ADB2504P-ADB2508P
ADB3504-ADB3508
ADB3504P-ADB3508P
ADB5004P-ADB5008P
AHBU604-AHBU608
ASB404L-ASB408L
B.
BAR1200D-BAR1210D
BAR2500D-BAR2510D
BAR3500-BAR3510
BAR3500D-BAR3510D
BAR3500S-BAR3510S
BAR5000-BAR5010
BAR5000D-BAR5010D
BAR5000S-BAR5010S
BAR6000-BAR6010
BAR6000D-BAR6010D
BAR6000S-BAR6010S
BAR7500-BAR7510
BAR7500D-BAR7510D
BAR7500S-BAR7510S
D.
DB300-DB310

PAGE
H1
H3
H19
H21
H7
H11
H13
A1
A5
A11
C17
C19
C23
A13
A15
A17
E13
E25
E31
E33
E35
E37
E39
E41
E43
E45
E51
E27
E15
K1
K3
K5
K9
K7
K11
K15
K13
K17
K21
K19
K23
K27
K25
E13

PART NUMBER
D. (Cont'd)
DB600-DB610
DB800-DB810
DB1000-DB1010
DB1500-DB1510
DB1500P-DB1510P
DB2500-DB2510
DB2500P-DB2510P
DB3500-DB3510
DB3500P-DB3510P
DB5000P-DB5010P
DI100-DI110
F.
FDB300-FDB310
FDB600-FDB610
FDB2500-FDB2510
FDB2500P-FDB2510P
FDB3500-FDB3510
FDB3500P-FDB3510P
FDI100-FDI110
FSB200-FSB210
FWB150-FWB1510
G.
GP100-GP110
GP200-GP210
GP400-GP410
GP600-GP610
GP1120-GP1500
H.
HBU600-HBU610
K.
KBL00-KBL10
P.
P6KE6.8-P6KE400CA
R.
RGP100-RGP110
RGP200-RGP210
RGP300-RGP310
RGP800-RGP806
RGP1120-RGP1500
RP100-RP110
RP300-RP310
RP600-RP610
S.
S1A-S1M
S1NB05-S1NB100
SB200-SB210
SB400L-SB410L

PAGE
E25
E31
E33
E35
E37
E39
E41
E43
E45
E51
E1
G7
G9
G11
G15
G13
G17
G1
G5
G3
H5
H9
H15
H17
I1
E27
E17
J19
H25
H27
H31
H35
I3
H23
H29
H33
H7
E3
E11
E15

PART NUMBER
S. (Cont'd)
SB500-SB510
SBU4A-SBU4M
SBU6A-SBU6M
SBU8A-SBU8M
SDB4000-SDB4010
SDB5000-SDB5010
SK102-SK110
SK302-SK310
SK502-SK510
SK1240C-SK12100C
SK1640C-SK16100C
SK2440C-SK24100C
SK3040C-SK30100C
SK4040C-SK40100C
SK6030C-SK6070C
SPR11-SPR14
SPR21-SPR23
SPR30-SPR34
SPR51-SPR54
SPR81-SPR86
SPR150-SPR156
SPR161C-SPR166C
SPR601C-SPR605C
SPR1001C-SPR1005C
SPR1601C-SPR1605C
T.
TVS3527
TVS3527D
TVS3527S
TVS5027
TVS5027S
TVS3527PFA
TVS3527PFC
TVS5027PFA
TVS5027PFC
U.
UFR24-UFR28
UFR100-UFR110
UFR300-UFR310
UFR400-UFR410
UFR600-UFR608
UFR3001C-UFR3005C
W.
WB100-WB110
WB150-WB1510
WB200-WB210

PAGE
E21
E19
E23
E29
E47
E49
A3
A7
A9
B1
B3
B5
B7
B9
B11
C1
C5
C7
C13
C21
C25
D7
D1
D3
D5
J1
J5
J3
J11
J13
J7
J9
J15
J17
C5
C3
C7
C11
C15
D9
E5
E7
E9

VII-1
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

THE SAMPLE REQUEST FORM IS ON THE REVERSE SIDE OF THIS PAGE

VIII-1
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

DIOTEC ELECTRONICS CORPORATION

SAMPLE REQUEST FORM

TO EXPEDITE YOUR REQUEST FOR PRODUCT SAMPLES, PLEASE FILL OUT THIS FORM
AND FAX IT TO US AT:

310-767-7958
NOTE: DIOTEC ELECTRONICS CORP. IS A LEADING MANUFACTURER OF HIGH QUALITY,
HIGH RELIABILTY POWER DIODES AND RECTIFIERS. WE SERVE THE OEM COMMUNITY.
RETAIL REQUESTS SHOULD BE DIRECTED TO NTE ELECTRONICS (WWW.NTEINC.COM)
OR DIGI-KEY (WWW.DIGIKEY.COM).
COMPANY :
ENGINEERING CONTACT:
CONTACT PHONE NUMBER:
CONTACT FAX NUMBER:
ADDRESS:
CITY
STATE
DIOTEC PART NUMBER(S):
NUMBER OF SAMPLES:
ESTIMATED ANNUAL USAGE:
TARGET PRICE:
APPLICATION:
NEW PRODUCT?
REDESIGN?
NEED ALTERNATE SUPPLIER?
CURRENT SUPPLIER:
CURRENT PART NUMBER
CURRENT PRICE:
COMMENTS:

TM

Combining a unique passivation material and void free vacuum die soldering, the SOFT GLASS DIODE
offers outstanding reliability under the harshest of operating conditions. The SOFT GLASS
passivation material uniquely provides the diode with unmatched protect against the negative
effects of aging, thermal/mechanical stress, and moisture. The features which clearly separate this
material from the industry's standard glass or rubber passivation are shown in the table below.

STRUCTURE

SOFT GLASS

RUBBER

BOND ENERGY

Similar to Standard Glass

For Low/High
Temperature Stability

Weak

TEMPERATURE RANGE

-100 to +250O C

MECHANICAL INTEGRITY

Relieves Thermal &

Mechanical Stresses

Rigid at Low Temperatures

Ages Quickly at
High Temperatures

STANDARD GLASS

Rigid And Brittle

Unlike the silicon rubber used in most low cost diodes, DIOTEC's SOFT GLASS is mostly inorganic.
Similar to glass, the basic structure of SOFT GLASS consists of repeating Silicon-Oxygen (Si-O) segments
The greater bond energy, and hence stability, of the Si-O linkages, as opposed to that of a Carbon-Carbon
(C-C) bond, enables SOFT GLASS to retain its high resiliency at temperatures as low as -100O C and is
remarkably stable (mechanically and electrically) at continuous temperatures as high as 250O C.
When compared to glass, which is rigid and brittle, SOFT GLASS is flexible within the diode's operational
temperature range. Therefore, it releases internal stresses caused by differences in the thermal
expansion coefficients of the different materials used to construct a diode. As a result, SOFT GLASS
protects diodes from the negative effects of aging, thermal/mechanicalstresses, and moisture.
DIOTEC's SOFT GLASS DIODES are identified in the Super Efficient/Ultrafast Diode, General Purpose
Diode, and Fast Recovery Diode Quick Selection Guides and applicable data sheets.
If you wish to try one or more of these diodes in your application, fill out the form in Appendix VIII or
simply give us a call. Our phone number is at the bottom of the page.

IX-1
DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected]

web site: www.diotec-usa.com e-mail: [email protected]

DIOTEC is thriving while its competitors, big

and small are dropping out!!
The reasons??

Very simple:

(A) DIOTEC offers a very comprehensive line of diodes

and rectifiers with excellent qualities.
(B) DIOTEC offers the Best Services in the business:
(1) Same Day Price Quotation (*)
(2) Samples delivered within three days (*)
(3) Orders delivered from stock (*)
(C) DIOTEC is able and more willing to go the extra distance
to assist you with your special requirements
(D) DIOTEC offers the most competitive prices. Unlike its major
competitors, DIOTEC runs the tightest ship and therefore has
the lowest overhead in this business. This allows DIOTEC to
keep its costs down and pass the savings on to its valued
customers.

So discuss your diode and rectifier needs with

DIOTEC now. Our knowledgeable sales and
technical staffs are ready to help you.

THE ONLY QUALITY RECTIFIERS AND DIODES

AT COMPETITIVE PRICES
(*) Except Specialty items