Understanding in Situ Combustion: Schlumberger: Heavy Oil

Schlumberger: Heavy oil
Page 01 of 02
Understanding
in situ combustion
In situ combustion (ISC) involves the injection of air, enriched-air,
or oxygen to enable combustion of oil within the reservoir
formation, creating chemical reactions and the release of CO2.
Heat ahead of the combustion front reduces viscosity and some
in situ distillation (upgrading) occurs. CO2 created during
combustion can also assist by increasing pressure and mixing
with the oil, further reducing viscosity and aiding flow.
PAUL NACCACHE
AND AUBREY
OCALLAGHAN,
SCHLUMBERGER.
OCTOBER 2007
he combustion and production zone between

injection and production well is typically tens
of feet wide. The combustion front is at around
8001000 degF (430540 degC). Sand screens and
perforated pipe can handle these temperatures.
The completions jewelry (e.g., packers) are kept
in the vertical section, where the produced oil
is cooler, typically around 300 degF (150 degC).
The primary limitation of the system is that the
combustion front is hard to control. However, ISC
has several benefits relative to steam injection
e.g., steam assisted gravity drainage (SAGD)
and cyclic steam stimulation (CSS).
Steam injection
RIGHT: WellWatcher
BriteBlue fiber
installation in a
heavy-oil well.
Engineers pump
the fiber through a
conduit inside a coiled
tubing string (inset)
that is hung from the
surface across the
producing interval.
Oil rec
overy
Steam injection requires treatment of water and

energy (usually gas) to heat the water, both of which
incur significant cost. ISC avoids these heat-related
costs, requiring only compressors for the injected
air. It should, however, be noted that ISC is not
freethe compressors are very powerful and quite
expensive. ISC requires very large volumes of air,
although not very high pressures, as these might
damage the formation.
Steam generation produces CO2 at the surface,
representing a significant environmental impact,
and heat is lost during transport to the formation.
ISC produces CO2 downhole, some of which may
Schlumberger: Heavy oil
subsequently be produced to surface, but probably

less than would be created during steam generation.
Steam injection systems can produce oil
economically and operators understand the
dynamics of these systems. By contrast, there is a
lack of confidence in ISC systems, despite the fact
that they have the potential to deliver significantly
higher recovery rates. In addition, until recently,
software tools and computer power were inadequate
to handle the complexities of modeling ISC.
ISC success stories
ABOVE: Fiber optics for

installation in a heavy
oil well, Canada
ISC success stories are limited. Although used in

the US during the 1950s and 1960s and in Venezuela
during the 1970s, ISC has often not been economical
due to low oil prices, so there is little worldwide
experience. Notable exceptions include Romania
and India. ISC in the Romanian Supalcu de Barcau
reservoir began in 1964, since then it has maintained
a production and a recovery factor of 56%. This and
several other successful thermal recovery projects
were celebrated at the SPE conference in Bucharest,
150 years of the Romanian Petroleum Industry,
in October 2007. In India, ONGC implemented ISC
in its Balol and Santhal heavy oil fields in 1997,
where recovery factors using conventional methods
had fallen to 615%. ISC increased recovery to 39
45%, producing an additional 8400 bbl/d. ONGC has
developed a special ignition technique for the project
to overcome the challenges of high pressures in wells
over 3,300 ft (1,000 m). Several new ISC pilot tests
are being performed in Canada and elsewhere and,
if successful, these could be the catalyst for a rapid
expansion of ISC usage worldwide. The technique
may not only be applicable for heavy oil. It has
also been considered for depleted conventional
oil reservoirs.
ISC requirements
ISC requirements include high permeability (e.g.,
35 Darcies), which is common in the shallow
depths in which heavy oil bearing formations are
usually found. It is most suitable for homogeneous
sandstones. Formation thickness is a key factor
determining well geometry and production strategy,
which must consider gravity effects. The high
well density required for ISC and other thermal
processes means that it is usually only economical
for shallow onshore reservoirs. Effective control
of air injection rates requires good up-front
experiments plus modeling and simulation based
on actual production rates. It is also important
to avoid breakthrough of air/oxygen from behind
the combustion front.
Page 02 of 02
The ECLIPSE Thermal simulator models

the burning and break-up of the hydrocarbon
components of the original oil in place (ooip) and
the chemical reactions that occur at or near the
combustion front during the ISC process. Coke is
considered as an intermediate component which
will burn so long as the temperature remains high
enough. The complex effects that happen ahead of
the combustion front are also accurately modeled.
Observations in laboratory combustion tubes
indicate very clean rock behind the combustion
front, with the clay minerals leached out, which
could lead to geomechanical problems. Literature
has mentioned the production of heavy metals from
the clay minerals mixing with the oilanother
consideration that should be tested in any pilot
study.
The key to the success of ISC is the will to do it.
A lot of reasons can be found by someone wanting
to take a more conventional approach. ISC can
pay dividends, although it needs comprehensive
planning, laboratory experiments, physical and
software modeling and simulation. An international
oil company (IOC) will generally own production
licenses for a finite duration so will need a fast
return on investment (ROI). By comparison, a
national oil company (NOC) may be more attracted
to the improved long-term recovery rates offered by
ISC, despite the up-front investment required for
studies. For both IOCs and NOCs, partnering with
companies that can provide experience, facilities
and technology will help to maximize returns.
Leveraging technology
Schlumberger has a wide range of technologies
applicable to heavy oil, such as specialist
proprietary completions and Sensa fiber optic
continuous well temperature monitoring systems.
It has a global support infrastructure and is
rapidly building its heavy oil knowledge base.
The Schlumberger DBR Technology Center in
Edmonton, Alberta, houses research and product
development activities focused on phase behavior,
flow assurance, enhanced oil recovery and heavy
oil production. This is part of a global network of
research, engineering and development facilities.
Heavy oil prices are increasing and the software
and hardware required to effectively model the
complexities of heavy oil thermal production have
only recently become available. In the future,
different production methods will find their own
niche, and among these, growing experience and
confidence will help to realize the benefits of ISC. n
WWW.SLB.COM/HEAVYOIL
* Mark of Schlumberger
Copyright 2011 Schlumberger Technology Corporation. All rights reserved.

Understanding in Situ Combustion: Schlumberger: Heavy Oil

Uploaded by

Copyright:

Available Formats

Understanding in Situ Combustion: Schlumberger: Heavy Oil

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Understanding in Situ Combustion: Schlumberger: Heavy Oil

Uploaded by

Copyright:

Available Formats

Schlumberger: Heavy oil

he combustion and production zone between

Steam injection requires treatment of water and

Schlumberger: Heavy oil

subsequently be produced to surface, but probably

ISC success stories

ABOVE: Fiber optics for

ISC success stories are limited. Although used in

The ECLIPSE Thermal simulator models

You might also like